LD1117A Low drop fixed and adjustable positive voltage regulators Datasheet - production data • Available in ± 2% (at 25 °C) and 4% in full temperature range • High supply voltage rejection: – 80 dB typ. (at 25 °C) SOT-223 • Temperature range: 0 °C to 125 °C TO-220 Description The LD1117A is a low drop voltage regulator able to provide up to 1 A of output current, available also in adjustable versions (V = 1.25V). In REF DPAK fixed versions, the following output voltages are offered: 1.2 V, 1.8 V, and 3.3 V. The device is supplied in: SOT-223, DPAK and TO-220. Surface Features mounted packages optimize the thermal characteristics while offering a relevant space • Low dropout voltage: saving advantage. High efficiency is assured by – 1.15 V typ. @ I = 1 A, 25 °C an NPN pass transistor. Only a very common 10 OUT µF minimum capacitor is needed for stability. Chip • Very low quiescent current: trimming allows the regulator to reach a very tight – 5 mA typ. @ 25 °C output voltage tolerance, within ± 2% at 25 °C. • Output current up to 1 A • Fixed output voltage of: – 1.2 V, 1.8 V, 3.3 V • Adjustable version availability (V = 1.25 V) REF • Internal current and thermal limit • Only 10 µF for stability Table 1. Device summary Order codes Output voltage SOT-223 DPAK TO-220 LD1117AS12TR LD1117ADT12TR 1.2 V LD1117AS18TR LD1117ADT18TR 1.8 V LD1117AS33TR LD1117ADT33TR LD1117AV33 3.3 V LD1117ASTR LD1117ADT-TR Adjustable from 1.25 V July 2013 DocID7194 Rev 26 1/24 This is information on a product in full production. www.st.com

Contents LD1117A Contents 1 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Schematic application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7 LD1117A adjustable: application note . . . . . . . . . . . . . . . . . . . . . . . . . . 12 8 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 9 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 2/24 DocID7194 Rev 26

LD1117A Diagram 1 Diagram Figure 1. Block diagram DocID7194 Rev 26 3/24 24

Pin configuration LD1117A 2 Pin configuration Figure 2. Pin connections (top view) INPUT 3 VIN OUTPUT 2 VOUT 1 ADJ/GND 1 2 3 ADJ/GND TO-220 ADJ/GND VOUT VIN DPAK SOT-223 Note: The TAB is connected to the V . OUT 4/24 DocID7194 Rev 26

LD1117A Maximum ratings 3 Maximum ratings Table 2. Absolute maximum ratings Symbol Parameter Value Unit V DC input voltage 15 V IN P Power dissipation 12 W D T Storage temperature range -40 to +150 °C STG T Operating junction temperature range 0 to +125 °C OP Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. Beyond the above suggested max. power dissipation, a short-circuit may permanently damage the device. Table 3. Thermal data Symbol Parameter SOT-223 DPAK TO-220 Unit R Thermal resistance junction-case 15 8 5 °C/W thJC R Thermal resistance junction-ambient 110 100 50 °C/W thJA DocID7194 Rev 26 5/24 24

Schematic application LD1117A 4 Schematic application Figure 3. Application circuit (for fixed output voltages) A 6/24 DocID7194 Rev 26

LD1117A Electrical characteristics 5 Electrical characteristics Refer to the test circuits, T = 0 to 125 °C, C = 10 µF, C = 10 µF, R = 120 Ω between OUT- J O I GND, unless otherwise specified. Table 4. Electrical characteristics of LD1117A#12 Symbol Parameter Test conditions Min. Typ. Max. Unit V Output voltage V = 5.3 V, I = 10 mA, T = 25 °C 1.176 1.2 1.224 V O I O J V Output voltage I = 0 to 1 A, V = 2.75 to 10 V 1.152 1.2 1.248 V O O I ΔV Line regulation V = 2.75 to 8 V, I = 0 mA 1 6 mV O I O ΔV Load regulation V = 2.75 V, I = 0 to 1 A 1 10 mV O I O ΔV Temperature stability 0.5 % O ΔV Long term stability 1000 hrs, T = 125 °C 0.3 % O J V Operating input voltage I = 100 mA 10 V I O I Quiescent current V ≤ 8 V, I = 0 mA 5 10 mA d I O I Output current V - V = 5 V, T = 25 °C 1000 1200 mA O I O J eN Output noise voltage B = 10 Hz to 10 kHz, T = 25 °C 100 µV J I = 40 mA, f = 120 Hz SVR Supply voltage rejection O 60 80 dB V - V = 3 V, V = 1 V I O ripple PP I = 100 mA 1 1.10 O V Dropout voltage I = 500 mA 1.05 1.15 V D O I = 1 A 1.15 1.30 O ΔV Thermal regulation T = 25 °C, 30 ms pulse 0.08 0.2 %/W O(pwr) a Refer to the test circuits, T = 0 to 125 °C, C = 10 µF, C = 10 µF, unless otherwise J O I specified. Table 5. Electrical characteristics of LD1117A#18 Symbol Parameter Test conditions Min. Typ. Max. Unit V Output voltage V = 3.8 V, I = 10 mA, T = 25 °C 1.764 1.8 1.836 V O I O J V Output voltage I = 0 to 1 A, V = 3.3 to 8 V 1.728 1.872 V O O I ΔV Line regulation V = 3.3 to 8 V, I = 0 mA 1 6 mV O I O ΔV Load regulation V = 3.3 V, I = 0 to 1 A 1 10 mV O I O ΔV Temperature stability 0.5 % O ΔV Long term stability 1000 hrs, T = 125 °C 0.3 % O J V Operating input voltage I = 100 mA 10 V I O I Quiescent current V ≤ 8 V, I = 0 mA 5 10 mA d I O I Output current V - V = 5 V, T = 25 °C 1000 mA O I O J DocID7194 Rev 26 7/24 24

Electrical characteristics LD1117A Table 5. Electrical characteristics of LD1117A#18 (continued) Symbol Parameter Test conditions Min. Typ. Max. Unit eN Output noise voltage B = 10 Hz to 10 kHz, T = 25 °C 100 µV J I = 40 mA, f = 120 Hz SVR Supply voltage rejection O 60 80 dB V - V = 3 V, V = 1 V I O ripple PP I = 100 mA 1 1.10 O V Dropout voltage I = 500 mA 1.05 1.15 V D O I = 1 A 1.15 1.30 O ΔV Thermal regulation T = 25 °C, 30 ms pulse 0.08 0.2 %/W O(pwr) a Refer to the test circuits, T = 0 to 125 °C, C = 10 µF, C = 10 µF, unless otherwise J O I specified. Table 6. Electrical characteristics of LD1117A#33 Symbol Parameter Test conditions Min. Typ. Max. Unit V Output voltage V = 5.3 V, I = 10 mA, T = 25 °C 3.234 3.3 3.366 V O I O J V Output voltage I = 0 to 1 A, V = 4.75 to 10 V 3.168 3.432 V O O I ΔV Line regulation V = 4.75 to 8 V, I = 0 mA 1 6 mV O I O ΔV Load regulation V = 4.75 V, I = 0 to 1 A 1 10 mV O I O ΔV Temperature stability 0.5 % O ΔV Long term stability 1000 hrs, T = 125 °C 0.3 % O J V Operating input voltage I = 100 mA 10 V I O I Quiescent current V ≤ 10 V, I = 0 mA 5 10 mA d I O I Output current V - V = 5 V, T = 25 °C 1000 1200 mA O I O J eN Output noise voltage B =10 Hz to 10 kHz, T = 25 °C 100 µV J I = 40 mA, f = 120 Hz SVR Supply voltage rejection O 60 75 dB V - V = 3 V, V = 1 V I O ripple PP I = 100 mA 1 1.10 O V Dropout voltage I = 500 mA 1.05 1.15 V D O I = 1 A 1.15 1.30 O ΔV Thermal regulation T = 25 °C, 30 ms pulse 0.08 0.2 %/W O(pwr) a Refer to the test circuits, T = 0 to 125 °C, C = 10 µF, C = 10 µF, unless otherwise J O I specified. Table 7. Electrical characteristics of LD1117A (adjustable) Symbol Parameter Test conditions Min. Typ. Max. Unit V Reference voltage V = 5.3 V, I = 10 mA, T = 25 °C 1.225 1.25 1.275 V REF I O J V Reference voltage I = 10 mA to 1 A, V = 2.75 to 10 V 1.2 1.3 V REF O I ΔV Line regulation V = 2.75 to 8 V, I = 0 mA 1 6 mV O I O 8/24 DocID7194 Rev 26

LD1117A Electrical characteristics Table 7. Electrical characteristics of LD1117A (adjustable) (continued) Symbol Parameter Test conditions Min. Typ. Max. Unit ΔV Load regulation V = 2.75 V, I = 0 to 1 A 1 10 mV O I O ΔV Temperature stability 0.5 % O ΔV Long term stability 1000 hrs, T = 125 °C 0.3 % O J V Operating input voltage I = 100 mA 10 V I O I Adjustment pin current V ≤ 10 V 60 120 µA adj in Adjustment pin current ΔI V - V = 1.4 to 10 V, I = 10 mA to 1 A 1 5 µA adj change in O O I Minimum load current V = 10 V 2 5 mA O(min) in I Output current V - V = 5 V, T = 25 °C 1000 1200 mA O I O J eN Output noise voltage B =10 Hz to 10 kHz, T = 25 °C 100 µV J I = 40 mA, f = 120 Hz SVR Supply voltage rejection O 60 80 dB V - V = 3 V, V = 1 V I O ripple PP I = 100 mA 1 1.10 O V Dropout voltage I = 500 mA 1.05 1.15 V D O I = 1 A 1.15 1.30 O ΔV Thermal regulation T = 25 °C, 30 ms pulse 0.08 0.2 %/W O(pwr) a DocID7194 Rev 26 9/24 24

Typical application LD1117A 6 Typical application Figure 4. Negative supply LD1117A VOUT = - VOUT(NOM) Figure 5. Circuit for increasing output voltage LD1117A VOUT = VOUT(NOM) + (0 - 5V) Figure 6. Voltage regulator with reference LD1117A VOUT = VOUT(NOM) + Vz Vz 10/24 DocID7194 Rev 26

LD1117A Typical application Figure 7. Post-regulated dual supply VOUT1 LD1117A VOUT2 = VOUT(NOM) 0.5 A LD1117A VOUT3 = -VOUT(NOM) 0.5 A DocID7194 Rev 26 11/24 24

LD1117A adjustable: application note LD1117A 7 LD1117A adjustable: application note The LD1117A adjustable has a thermal stabilized 1.25 ± 0.012 V reference voltage between the OUT and ADJ pins. I is 60 µA typ. (120 µA max.) and ΔI is 1 µA typ. (5 µA max.). ADJ ADJ R is normally fixed to 120 Ω. From Figure6 the following is obtained: 1 V = V + R (I + I ) = V + R (I +V /R ) = V (1 + R / R ) + R x OUT REF 2 ADJ R1 REF 2 ADJ REF 1 REF 2 1 2 I . ADJ In normal applications the R value is in the range of a few kΩ, so the R x I product can 2 2 ADJ not be considered in the V calculation; the above expression then becomes: OUT V = V (1 + R / R ). OUT REF 2 1 In order to have a better load regulation it is important to realize a good Kelvin connection of R and R resistors. In particular, the R connection must be realized very close to the OUT 1 2 1 and ADJ pins, while the R ground connection must be placed as near as possible to the 2 negative load pin. Ripple rejection can be improved by introducing a 10 µF electrolytic capacitor placed in parallel to the R resistor (see Figure8). 2 Figure 8. Adjustable output voltage application LD1117A Figure 9. Adjustable output voltage application with improved ripple rejection LD1117A 12/24 DocID7194 Rev 26

LD1117A Package mechanical data 8 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Table 8. TO-220 SG (single gauge) mechanical data mm Dim. Min. Typ. Max. A 4.40 4.60 b 0.61 0.88 b1 1.14 1.70 c 0.48 0.70 D 15.25 15.75 E 10 10.40 e 2.40 2.70 e1 4.95 5.15 F 0.51 0.60 H1 6.20 6.60 J1 2.40 2.72 L 13 14 L1 3.50 3.93 L20 16.40 L30 28.90 ∅ P 3.75 3.85 Q 2.65 2.95 DocID7194 Rev 26 13/24 24

Package mechanical data LD1117A Figure 10. TO-220 SG (single gauge) drawing (cid:27)(cid:20)(cid:26)(cid:23)(cid:25)(cid:21)(cid:26)(cid:66)(cid:85)(cid:72)(cid:89)(cid:39) 14/24 DocID7194 Rev 26

LD1117A Package mechanical data Table 9. SOT-223 mechanical data mm Dim. Min. Typ. Max. A 1.80 A1 0.02 0.1 B 0.60 0.70 0.85 B1 2.90 3.00 3.15 c 0.24 0.26 0.35 D 6.30 6.50 6.70 e 2.30 e1 4.60 E 3.30 3.50 3.70 H 6.70 7.00 7.30 V 10° Figure 11. SOT-223 mechanical data drawing 0046067_M DocID7194 Rev 26 15/24 24

Package mechanical data LD1117A Table 10. DPAK (TO-252) mechanical data mm Dim. Min. Typ. Max. A 2.20 2.40 A1 0.90 1.10 A2 0.03 0.23 b 0.64 0.90 b4 5.20 5.40 c 0.45 0.60 c2 0.48 0.60 D 6.00 6.20 D1 5.10 E 6.40 6.60 E1 4.70 e 2.28 e1 4.40 4.60 H 9.35 10.10 L 1.00 1.50 (L1) 2.80 L2 0.80 L4 0.60 1.00 R 0.20 V2 0° 8° 16/24 DocID7194 Rev 26

LD1117A Package mechanical data Figure 12. DPAK (TO-252) drawing 0068772_K DocID7194 Rev 26 17/24 24

Package mechanical data LD1117A Figure 13. DPAK footprint (a) Footprint_REV_K a. All dimensions are in millimeters 18/24 DocID7194 Rev 26

LD1117A Packaging mechanical data 9 Packaging mechanical data Table 11. SOT-223 tape and reel mechanical data Tape Reel mm mm Dim. Dim. Min. Typ. Max. Min. Max. A0 6.75 6.85 6.95 A 180 B0 7.30 7.40 7.50 N 60 K0 1.80 1.90 2.00 W1 12.4 F 5.40 5.50 5.60 W2 18.4 E 1.65 1.75 1.85 W3 11.9 15.4 W 11.7 12 12.3 P2 1.90 2 2.10 Base quantity pcs 1000 P0 3.90 4 4.10 Bulk quantity pcs 1000 P1 7.90 8 8.10 T 0.25 0.30 0.35 Df 1.50 1.55 1.60 D1f 1.50 1.60 1.70 Figure 14. Tape for SOT-223 (dimensions are in mm) *Cumulative tolerance of 10 sprocket holes is ±0.20 mm DocID7194 Rev 26 19/24 24

Packaging mechanical data LD1117A Figure 15. Reel for SOT-223 (dimensions are in mm) 20/24 DocID7194 Rev 26

LD1117A Packaging mechanical data Table 12. DPAK tape and reel mechanical data Tape Reel mm mm Dim. Dim. Min. Max. Min. Max. A0 6.8 7 A 330 B0 10.4 10.6 B 1.5 B1 12.1 C 12.8 13.2 D 1.5 1.6 D 20.2 D1 1.5 G 16.4 18.4 E 1.65 1.85 N 50 F 7.4 7.6 T 22.4 K0 2.55 2.75 P0 3.9 4.1 Base qty. 2500 P1 7.9 8.1 Bulk qty. 2500 P2 1.9 2.1 R 40 T 0.25 0.35 W 15.7 16.3 DocID7194 Rev 26 21/24 24

Packaging mechanical data LD1117A Figure 16. Tape for DPAK 10 pitches cumulative tolerance on tape +/- 0.2 mm Top cover P0 D P2 T tape E F K0 W B1 B0 For machine ref. only A0 P1 D1 including draft and radii concentric around B0 User direction of feed R Bending radius User direction of feed AM08852v1 Figure 17. Reel for DPAK T REEL DIMENSIONS 40mm min. Access hole At sl ot location B D C N A Full radius Tape slot G measured at hub in core for tape start 25 mm min. width AM08851v2 22/24 DocID7194 Rev 26

LD1117A Revision history 10 Revision history Table 13. Document revision history Date Revision Changes 29-Sep-2004 11 Add new part number. 12-Oct-2004 12 Mistake V max. - Table 4. O 21-Apr-2005 13 Add new package - D²PAK/A. 05-Jul-2005 14 The DPAK mechanical data updated. 10-Feb-2006 15 Add new package - D²PAK/A (B type). 20-Dec-2006 16 Change value V on Table2. IN 19-Jan-2007 17 D²PAK/A mechanical data updated and add footprint data. 28-May-2007 18 Add I and ΔI values on Table7. ADJ ADJ 07-Jun-2007 19 Add I value on Table7. O(min) 15-Apr-2008 20 Modified: Table 10. 28-Jul-2009 21 Modified: Table 10. Added: Table8 on page15, Figure14 on page18, Figure15 on page20, 05-Jul-2010 22 Figure16 and Figure17 on page21. 16-Nov-2010 23 Modified: Table1 on page1, R value for TO-220 Table3 on page5. thJC Modified: V parameter output voltage ==> Reference voltage Table7 on 16-Dec-2011 24 O page8. 19-Oct-2012 25 Added: R value for DPAK and SOT-223 Table3 on page5. thJA Part numbers LD1117AXX12, LD1117AXX18, LD1117AXX33, LD1117AXX changed to LD1117A. Modified Chapter6: Typical application. Changed Vo symbol in to V in Table7: Electrical characteristics of LD1117A 24-Jul-2013 26 REF (adjustable). Updated Chapter8: Package mechanical data. Added Chapter9: Packaging mechanical data. Minor text changes. DocID7194 Rev 26 23/24 24

LD1117A Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT AUTHORIZED FOR USE IN WEAPONS. NOR ARE ST PRODUCTS DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2013 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 24/24 DocID7194 Rev 26

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: S TMicroelectronics: LD1117AV33 LD1117ADT18TR LD1117ADT-TR LD1117AS12TR LD1117ASTR LD1117ADT33TR LD1117AS18TR LD1117AS33TR LD1117ADT12TR