Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product Information in this Catalog (4) Power generation control equipment (nuclear power, Product information in this catalog is as of October 2019. All of the hydroelectric power, thermal power plant control system, etc.) contents specified herein and production status of the products listed (5) Undersea equipment (submarine repeating equipment, in this catalog are subject to change without notice due to technical underwater work equipment, etc.) improvement of our products, etc. Therefore, please check for the (6) Military equipment latest information carefully before practical application or use of our (7) Any other equipment requiring extremely high levels of safety products. and/or reliability equal to the equipment listed above Please note that TAIYO YUDEN shall not be in any way responsible *Notes: for any damages and defects in products or equipment incorporating 1. There is a possibility that our products can be used only our products, which are caused under the conditions other than those for aviation equipment that does not directly affect the safe specified in this catalog or individual product specification sheets. operation of aircraft (e.g., in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets ■ Approval of Product Specifications requirements specified separately by TAIYO YUDEN. Please Please contact TAIYO YUDEN for further details of product be sure to contact TAIYO YUDEN for further information specifications as the individual product specification sheets are before using our products for such aviation equipment. available. When using our products, please be sure to approve our 2. Implantable medical devices contain not only internal unit product specifications or make a written agreement on the product which is implanted in a body, but also external unit which is specification with TAIYO YUDEN in advance. connected to the internal unit. ■ Pre-Evaluation in the Actual Equipment and Conditions 4. Limitation of Liability Please conduct validation and verification of our products in actual Please note that unless you obtain prior written consent of TAIYO conditions of mounting and operating environment before using our YUDEN, TAIYO YUDEN shall not be in any way responsible for products. any damages incurred by you or third parties arising from use of the products listed in this catalog for any equipment that is not ■ Limited Application intended for use by TAIYO YUDEN, or any equipment requiring 1. Equipment Intended for Use inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN The products listed in this catalog are intended for general- as described above. purpose and standard use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office ■ Safety Design equipment, information and communication equipment including, When using our products for high safety and/or reliability-required without limitation, mobile phone, and PC) and other equipment equipment or circuits, please fully perform safety and/or reliability specified in this catalog or the individual product specification sheets. evaluation. In addition, please install (i) systems equipped with a protection circuit and a protection device and/or (ii) systems TAIYO YUDEN has the line-up of the products intended for equipped with a redundant circuit or other system to prevent an use in automotive electronic equipment, telecommunications unsafe status in the event of a single fault for a failsafe design to infrastructure and industrial equipment, or medical devices ensure safety. classified as GHTF Classes A to C (Japan Classes I to III). Therefore, when using our products for these equipment, ■ Intellectual Property Rights please check available applications specified in this catalog Information contained in this catalog is intended to convey examples or the individual product specification sheets and use the of typical performances and/or applications of our products and is corresponding products. not intended to make any warranty with respect to the intellectual property rights or any other related rights of TAIYO YUDEN or any 2. Equipment Requiring Inquiry third parties nor grant any license under such rights. Please be sure to contact TAIYO YUDEN for further information before using the products listed in this catalog for the following ■ Limited Warranty equipment (excluding intended equipment as specified in this Please note that the scope of warranty for our products is limited to catalog or the individual product specification sheets) which may the delivered our products themselves and TAIYO YUDEN shall not cause loss of human life, bodily injury, serious property damage be in any way responsible for any damages resulting from a failure and/or serious public impact due to a failure or defect of the or defect in our products. Notwithstanding the foregoing, if there is products and/or malfunction attributed thereto. a written agreement (e.g., supply and purchase agreement, quality (1) Transportation equipment (automotive powertrain control assurance agreement) signed by TAIYO YUDEN and your company, system, train control system, and ship control system, etc.) TAIYO YUDEN will warrant our products in accordance with such (2) Traffic signal equipment agreement. (3) Disaster prevention equipment, crime prevention equipment (4) Medical devices classified as GHTF Class C (Japan Class III) ■ TAIYO YUDEN’s Official Sales Channel (5) Highly public information network equipment, data- The contents of this catalog are applicable to our products which are processing equipment (telephone exchange, and base purchased from our sales offices or authorized distributors (hereinafter station, etc.) “TAIYO YUDEN’s official sales channel”). Please note that the contents (6) Any other equipment requiring high levels of quality and/or of this catalog are not applicable to our products purchased from any reliability equal to the equipment listed above seller other than TAIYO YUDEN’s official sales channel. 3. Equipment Prohibited for Use ■ Caution for Export Please do not incorporate our products into the following Some of our products listed in this catalog may require specific equipment requiring extremely high levels of safety and/or procedures for export according to“ U.S. Export Administration reliability. Regulations”,“ Foreign Exchange and Foreign Trade Control Law” (1) Aerospace equipment (artificial satellite, rocket, etc.) of Japan, and other applicable regulations. Should you have any (2) Aviation equipment *1 questions on this matter, please contact our sales staff. (3) Medical devices classified as GHTF Class D (Japan Class IV), implantable medical devices *2 20

for General Electronic Equipment for General Electronic Equipment WIRE-WOUND CHIP INDUCTORS (LB SERIES) WIRE-WOUND CHIP INDUCTORS（LB SERIES） REFLOW REFLOW ■PARTS NUMBER * Operating Temp.：-40～+105℃（Including self-generated heat） L B △ △ 2 0 1 2 T 1 0 0 M △ △ △ △ △＝Blank space ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ①Series name ④Packaging IN Code Series name Code Packaging D U LB Wound chip inductor T Taping C T O R ②Characteristics ⑤Nominal inductance S Code Characteristics Code Nominal inductance［μH］ △△ Standard （example） △C High current 1R0 1.0 ST △R Low Rdc 100 10 A MF Low loss 101 100 N ※R＝Decimal point D ③Dimensions（L×W） A R Dimensions ⑥Inductance tolerance D Code Type（inch） （L×W）［mm］ Code Inductance tolerance IN 1608 1608（0603） 1.6×0.8 K ±10％ D 2012 2012（0805） 2.0×1.25 M ±20％ U 2016 2016（0806） 2.0×1.6 C 2518 2518（1007） 2.5×1.8 ⑦Special code T O 3218 3218（1207） 3.2×1.8 Code Special code R 3225 3225（1210） 3.2×2.5 △ Standard S R Low Rdc type ⑧Internal code ■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY Recommended Land Patterns Surface Mounting LB／LB C／LB R LBMF ・Mounting and soldering conditions should be checked beforehand. ・Applicable soldering process to these products is reflow soldering only. Type A B C W W 1608 0.55 0.7 0.9 L L C MF1608 0.55 0.7 1.0 T T 2012 0.60 1.0 1.45 2016 0.60 1.0 1.8 e e 2518 0.60 1.5 2.0 A B A 3218 0.85 1.7 2.0 3225 0.85 1.7 2.7 Unit：mm Standard quantity［pcs］ Type L W T e Paper tape Embossed tape 1.6±0.1 0.8±0.1 0.8±0.1 0.35±0.15 LB 1608 4000 － （0.063±0.004） （0.031±0.004） （0.031±0.004） （0.014±0.006） 1.6±0.2 0.8±0.2 0.8±0.2 0.45±0.15 LBMF1608 － 3000 （0.063±0.008） （0.031±0.008） （0.031±0.008） （0.016±0.006） LB 2012 2.0±0.2 1.25±0.2 1.25±0.2 0.5±0.2 LB C2012 － 3000 （0.079±0.008） （0.049±0.008） （0.049±0.008） （0.020±0.008） LB R2012 LB 2016 2.0±0.2 1.6±0.2 1.6±0.2 0.5±0.2 － 2000 LB C2016 （0.079±0.008） （0.063±0.008） （0.063±0.008） （0.020±0.008） LB 2518 2.5±0.2 1.8±0.2 1.8±0.2 0.5±0.2 LB C2518 － 2000 （0.098±0.008） （0.071±0.008） （0.071±0.008） （0.020±0.008） LB R2518 3.2±0.2 1.8±0.2 1.8±0.2 0.6±0.2 LB 3218 － 2000 （0.126±0.008） （0.071±0.008） （0.071±0.008） （0.024±0.008） 3.2±0.2 2.5±0.2 2.5±0.2 0.6±0.3 LB C3225 － 1000 （0.126±0.008） （0.098±0.008） （0.098±0.008） （0.024±0.012） Unit：mm（inch） i_wound_LB_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 82 20

for General Electronic Equipment ■PARTS NUMBER ●1608（0603）type Nominal inductance Self-resonant frequency DC Resistance Rated current Measuring frequency Parts number EHS Inductance tolerance ［μH］ ［MHｚ］（min.） ［Ω］（±30％） ［mA］（max.） ［MHz］ LB 1608T1R0M RoHS 1.0 ±20％ 100 0.17 160 7.96 LB 1608T2R2M RoHS 2.2 ±20％ 80 0.33 115 7.96 LB 1608T4R7M RoHS 4.7 ±20％ 45 0.55 70 7.96 LB 1608T8R2M RoHS 8.2 ±20％ 32 0.70 60 2.52 LB 1608T100M RoHS 10 ±20％ 32 0.70 60 2.52 Nominal inductance Self-resonant frequency DC Resistance Rated current Measuring frequency Parts number EHS Inductance tolerance ［μH］ ［MHｚ］（min.） ［Ω］（±30％） ［mA］（max.） ［MHz］ LBMF1608T1R0M RoHS 1.0 ±20％ 100 0.09 230 7.96 LBMF1608T2R2M RoHS 2.2 ±20％ 80 0.17 160 7.96 LBMF1608T3R3M RoHS 3.3 ±20％ 60 0.22 130 7.96 IN LBMF1608T4R7M RoHS 4.7 ±20％ 45 0.24 110 7.96 D LBMF1608T100[] RoHS 10 ±10％，±20％ 32 0.36 80 2.52 U C LBMF1608T220[] RoHS 22 ±10％，±20％ 16 1.0 50 2.52 T LBMF1608T470[] RoHS 47 ±10％，±20％ 11 2.5 35 2.52 O R S ●2012（0805）type Nominal inductance Self-resonant frequency DC Resistance Rated current Measuring frequency Parts number EHS Inductance tolerance ［μH］ ［MHｚ］（min.） ［Ω］（±30％） ［mA］（max.） ［MHz］ LB 2012T1R0M RoHS 1.0 ±20％ 100 0.15 405 7.96 S T LB 2012T2R2M RoHS 2.2 ±20％ 80 0.23 260 7.96 A LB 2012T3R3M RoHS 3.3 ±20％ 55 0.30 235 7.96 N LB 2012T4R7M RoHS 4.7 ±20％ 45 0.40 190 7.96 D LB 2012T6R8M RoHS 6.8 ±20％ 38 0.47 135 7.96 A LB 2012T100[] RoHS 10 ±10％，±20％ 32 0.70 120 2.52 R LB 2012T100[]R RoHS 10 ±10％，±20％ 32 0.50 120 2.52 D LB 2012T150[] RoHS 15 ±10％，±20％ 28 1.3 100 2.52 LB 2012T220[] RoHS 22 ±10％，±20％ 16 1.7 80 2.52 IN LB 2012T470[] RoHS 47 ±10％，±20％ 11 3.7 60 2.52 D LB 2012T680[] RoHS 68 ±10％，±20％ 10 6.0 50 2.52 U LB 2012T101[] RoHS 100 ±10％，±20％ 8 7.0 45 0.796 C T Nominal inductance Self-resonant frequency DC Resistance Rated current Measuring frequency O Parts number EHS Inductance tolerance ［μH］ ［MHｚ］（min.） ［Ω］（±30％） ［mA］（max.） ［MHz］ R LB C2012T1R0M RoHS 1.0 ±20％ 100 0.19 620 7.96 S LB C2012T2R2M RoHS 2.2 ±20％ 70 0.33 430 7.96 LB C2012T4R7M RoHS 4.7 ±20％ 45 0.50 295 7.96 LB C2012T100[] RoHS 10 ±10％，±20％ 40 1.2 200 2.52 LB C2012T220[] RoHS 22 ±10％，±20％ 16 3.7 130 2.52 LB C2012T470[] RoHS 47 ±10％，±20％ 11 5.8 90 2.52 Nominal inductance Self-resonant frequency DC Resistance Rated current Measuring frequency Parts number EHS Inductance tolerance ［μH］ ［MHｚ］（min.） ［Ω］（±30％） ［mA］（max.） ［MHz］ LB R2012T1R0M RoHS 1.0 ±20％ 100 0.07 400 7.96 LB R2012T2R2M RoHS 2.2 ±20％ 80 0.13 260 7.96 LB R2012T4R7M RoHS 4.7 ±20％ 45 0.24 200 7.96 LB R2012T100[] RoHS 10 ±10％，±20％ 32 0.36 150 2.52 LB R2012T220[] RoHS 22 ±10％，±20％ 16 1.0 100 2.52 LB R2012T470[] RoHS 47 ±10％，±20％ 11 1.7 75 2.52 LB R2012T101[] RoHS 100 ±10％，±20％ 8 4.0 50 0.796 ●2016（0806）type Nominal inductance Self-resonant frequency DC Resistance Rated current Measuring frequency Parts number EHS Inductance tolerance ［μH］ ［MHｚ］（min.） ［Ω］（±30％） ［mA］（max.） ［MHz］ LB 2016T1R0M RoHS 1.0 ±20％ 100 0.09 490 7.96 LB 2016T1R5M RoHS 1.5 ±20％ 80 0.11 380 7.96 LB 2016T2R2M RoHS 2.2 ±20％ 70 0.13 375 7.96 LB 2016T3R3M RoHS 3.3 ±20％ 55 0.20 285 7.96 LB 2016T4R7M RoHS 4.7 ±20％ 45 0.25 225 7.96 LB 2016T6R8M RoHS 6.8 ±20％ 38 0.35 200 7.96 LB 2016T100[] RoHS 10 ±10％，±20％ 32 0.50 155 2.52 LB 2016T150[] RoHS 15 ±10％，±20％ 28 0.70 130 2.52 LB 2016T220[] RoHS 22 ±10％，±20％ 16 1.0 105 2.52 LB 2016T330[] RoHS 33 ±10％，±20％ 14 1.7 85 2.52 LB 2016T470[] RoHS 47 ±10％，±20％ 11 2.4 70 2.52 LB 2016T680[] RoHS 68 ±10％，±20％ 10 3.0 55 2.52 LB 2016T101[] RoHS 100 ±10％，±20％ 8 4.5 40 0.796 ・ [] Please specify the Inductance tolerance code（K or M） LB/LBC series Rated Current : The maximum DC value having inductance decrease within 10 % and temperature increase within 20 degC by the application of DC bias. LBR series Rated Current : The maximum DC value having inductance decrease within 20 % and temperature increase within 20 degC by the application of DC bias. i_wound_LB_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 20 83

for General Electronic Equipment ■PARTS NUMBER Nominal inductance Self-resonant frequency DC Resistance Rated current Measuring frequency Parts number EHS Inductance tolerance ［μH］ ［MHｚ］（min.） ［Ω］（±30％） ［mA］（max.） ［MHz］ LB C2016T1R0M RoHS 1.0 ±20％ 100 0.10 690 7.96 LB C2016T1R5M RoHS 1.5 ±20％ 80 0.15 600 7.96 LB C2016T2R2M RoHS 2.2 ±20％ 70 0.20 520 7.96 LB C2016T3R3M RoHS 3.3 ±20％ 55 0.27 410 7.96 LB C2016T4R7M RoHS 4.7 ±20％ 45 0.37 355 7.96 LB C2016T6R8M RoHS 6.8 ±20％ 38 0.59 290 7.96 LB C2016T100[] RoHS 10 ±10％，±20％ 32 0.82 245 2.52 LB C2016T150[] RoHS 15 ±10％，±20％ 28 1.2 200 2.52 LB C2016T220[] RoHS 22 ±10％，±20％ 16 1.8 165 2.52 LB C2016T330[] RoHS 33 ±10％，±20％ 14 2.8 135 2.52 LB C2016T470[] RoHS 47 ±10％，±20％ 11 4.3 110 2.52 IN LB C2016T680[] RoHS 68 ±10％，±20％ 10 7.0 95 2.52 D LB C2016T101[] RoHS 100 ±10％，±20％ 8 8.0 75 0.796 U C T ●2518（1007）type O Nominal inductance Self-resonant frequency DC Resistance Rated current Measuring frequency RS Parts number EHS ［μH］ Inductance tolerance ［MHｚ］（min.） ［Ω］（±30％） ［mA］（max.） ［MHz］ LB 2518T1R0M RoHS 1.0 ±20％ 100 0.06 665 7.96 LB 2518T1R5M RoHS 1.5 ±20％ 80 0.07 405 7.96 LB 2518T2R2M RoHS 2.2 ±20％ 68 0.09 340 7.96 S LB 2518T3R3M RoHS 3.3 ±20％ 54 0.11 280 7.96 T A LB 2518T4R7M RoHS 4.7 ±20％ 46 0.13 240 7.96 N LB 2518T4R7MR RoHS 4.7 ±20％ 46 0.10 235 7.96 D LB 2518T6R8M RoHS 6.8 ±20％ 38 0.15 195 7.96 A LB 2518T100[] RoHS 10 ±10％，±20％ 30 0.25 165 2.52 R LB 2518T150[] RoHS 15 ±10％，±20％ 23 0.32 145 2.52 D LB 2518T220[] RoHS 22 ±10％，±20％ 19 0.50 115 2.52 LB 2518T330[] RoHS 33 ±10％，±20％ 15 0.70 95 2.52 IN LB 2518T470[] RoHS 47 ±10％，±20％ 12 0.95 85 2.52 D LB 2518T680[] RoHS 68 ±10％，±20％ 9.5 1.5 70 2.52 U LB 2518T101[] RoHS 100 ±10％，±20％ 9.0 2.1 60 0.796 C LB 2518T151[] RoHS 150 ±10％，±20％ 7.0 3.2 45 0.796 T LB 2518T221[] RoHS 220 ±10％，±20％ 5.5 4.5 40 0.796 O LB 2518T331[] RoHS 330 ±10％，±20％ 4.5 7.0 30 0.796 R LB 2518T471[] RoHS 470 ±10％，±20％ 3.5 10 25 0.796 S LB 2518T681[] RoHS 680 ±10％，±20％ 3.0 17 20 0.796 LB 2518T102[] RoHS 1000 ±10％，±20％ 2.4 24 15 0.252 Nominal inductance Self-resonant frequency DC Resistance Rated current Measuring frequency Parts number EHS Inductance tolerance ［μH］ ［MHｚ］（min.） ［Ω］（±30％） ［mA］（max.） ［MHz］ LB C2518T1R0M RoHS 1.0 ±20％ 100 0.08 775 7.96 LB C2518T1R0MR RoHS 1.0 ±20％ 100 0.07 890 7.96 LB C2518T1R5M RoHS 1.5 ±20％ 80 0.11 730 7.96 LB C2518T2R2M RoHS 2.2 ±20％ 68 0.13 630 7.96 LB C2518T3R3M RoHS 3.3 ±20％ 54 0.16 560 7.96 LB C2518T4R7M RoHS 4.7 ±20％ 41 0.20 510 7.96 LB C2518T6R8M RoHS 6.8 ±20％ 38 0.30 420 7.96 LB C2518T100[] RoHS 10 ±10％，±20％ 30 0.36 375 2.52 LB C2518T150[] RoHS 15 ±10％，±20％ 23 0.65 285 2.52 LB C2518T220[] RoHS 22 ±10％，±20％ 19 0.77 250 2.52 LB C2518T330[] RoHS 33 ±10％，±20％ 15 1.5 185 2.52 LB C2518T470[] RoHS 47 ±10％，±20％ 12 1.9 165 2.52 LB C2518T680[] RoHS 68 ±10％，±20％ 9.5 2.8 140 2.52 LB C2518T101[] RoHS 100 ±10％，±20％ 9.0 3.7 125 0.796 LB C2518T151[] RoHS 150 ±10％，±20％ 7.0 6.1 95 0.796 LB C2518T221[] RoHS 220 ±10％，±20％ 5.5 8.4 80 0.796 LB C2518T331[] RoHS 330 ±10％，±20％ 4.5 12.3 65 0.796 LB C2518T471[] RoHS 470 ±10％，±20％ 3.5 22 50 0.796 LB C2518T681[] RoHS 680 ±10％，±20％ 3.0 28 45 0.796 Nominal inductance Self-resonant frequency DC Resistance Rated current Measuring frequency Parts number EHS Inductance tolerance ［μH］ ［MHｚ］（min.） ［Ω］（±30％） ［mA］（max.） ［MHz］ LB R2518T1R0M RoHS 1.0 ±20％ 100 0.045 960 7.96 LB R2518T2R2M RoHS 2.2 ±20％ 68 0.07 480 7.96 LB R2518T4R7M RoHS 4.7 ±20％ 45 0.10 345 7.96 LB R2518T100[] RoHS 10 ±10％，±20％ 30 0.19 235 2.52 LB R2518T220[] RoHS 22 ±10％，±20％ 19 0.44 175 2.52 LB R2518T470[] RoHS 47 ±10％，±20％ 11 0.84 120 2.52 LB R2518T101[] RoHS 100 ±10％，±20％ 9 1.89 80 0.796 ・ [] Please specify the Inductance tolerance code（K or M） LB/LBC series Rated Current : The maximum DC value having inductance decrease within 10 % and temperature increase within 20 degC by the application of DC bias. LBR series Rated Current : The maximum DC value having inductance decrease within 20 % and temperature increase within 20 degC by the application of DC bias. i_wound_LB_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 84 20

for General Electronic Equipment ■PARTS NUMBER ●3218（1207）type Nominal inductance Self-resonant frequency DC Resistance Rated current Measuring frequency Parts number EHS Inductance tolerance ［μH］ ［MHｚ］（min.） ［Ω］（±30％） ［mA］（max.） ［MHz］ LB 3218T1R0M RoHS 1.0 ±20％ 100 0.06 1,075 7.96 LB 3218T1R5M RoHS 1.5 ±20％ 80 0.07 860 7.96 LB 3218T2R2M RoHS 2.2 ±20％ 68 0.09 775 7.96 LB 3218T3R3M RoHS 3.3 ±20％ 54 0.11 560 7.96 LB 3218T4R7M RoHS 4.7 ±20％ 41 0.13 550 7.96 LB 3218T6R8M RoHS 6.8 ±20％ 40 0.17 380 7.96 LB 3218T100[] RoHS 10 ±10％，±20％ 30 0.25 340 2.52 LB 3218T150[] RoHS 15 ±10％，±20％ 25 0.32 300 2.52 LB 3218T220[] RoHS 22 ±10％，±20％ 19 0.49 255 2.52 LB 3218T330[] RoHS 33 ±10％，±20％ 15 0.75 215 2.52 LB 3218T470[] RoHS 47 ±10％，±20％ 12 0.92 205 2.52 IN LB 3218T680[] RoHS 68 ±10％，±20％ 11 1.49 145 2.52 D LB 3218T101[] RoHS 100 ±10％，±20％ 8.0 2.4 140 0.796 U C LB 3218T151[] RoHS 150 ±10％，±20％ 7.0 3.2 105 0.796 T LB 3218T221[] RoHS 220 ±10％，±20％ 5.0 5.4 80 0.796 O R LB 3218T331[] RoHS 330 ±10％，±20％ 4.0 7.0 65 0.796 S LB 3218T471[] RoHS 470 ±10％，±20％ 3.5 14 54 0.796 LB 3218T681[] RoHS 680 ±10％，±20％ 3.0 17 45 0.796 LB 3218T102[] RoHS 1000 ±10％，±20％ 2.4 27 39 0.252 S T ●3225（1210）type A Parts number EHS Nominal inductance Inductance tolerance Self-resonant frequency DC Resistance Rated current Measuring frequency N ［μH］ ［MHｚ］（min.） ［Ω］（±30％） ［mA］（max.） ［MHz］ D LB C3225T1R0MR RoHS 1.0 ±20％ 250 0.055 1,100 0.1 A LB C3225T1R5MR RoHS 1.5 ±20％ 220 0.060 1,000 0.1 R LB C3225T2R2MR RoHS 2.2 ±20％ 190 0.080 930 0.1 D LB C3225T3R3MR RoHS 3.3 ±20％ 160 0.095 820 0.1 LB C3225T4R7MR RoHS 4.7 ±20％ 70 0.100 680 0.1 IN LB C3225T6R8MR RoHS 6.8 ±20％ 50 0.120 620 0.1 D LB C3225T100[]R RoHS 10 ±10％，±20％ 23 0.133 540 0.1 U LB C3225T150[]R RoHS 15 ±10％，±20％ 20 0.195 420 0.1 C LB C3225T220[]R RoHS 22 ±10％，±20％ 17 0.27 330 0.1 T LB C3225T330[]R RoHS 33 ±10％，±20％ 13 0.41 300 0.1 O LB C3225T470[]R RoHS 47 ±10％，±20％ 10 0.67 220 0.1 R LB C3225T680[]R RoHS 68 ±10％，±20％ 8 1.0 190 0.1 S LB C3225T101[]R RoHS 100 ±10％，±20％ 6 1.4 150 0.1 ・ [] Please specify the Inductance tolerance code（K or M） LB/LBC series Rated Current : The maximum DC value having inductance decrease within 10 % and temperature increase within 20 degC by the application of DC bias. i_wound_LB_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 20 85

WIRE-WOUND CHIP INDUCTORS (LB SERIES)， WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES)， WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) ■PACKAGING ①Minimum Quantity Standard Quantity ［pcs］ Type Paper Tape Embossed Tape LB C3225 － 1000 CB C3225 LB 3218 － 2000 LB R2518 LB C2518 LB 2518 － 2000 CB 2518 CB C2518 LBM2016 LB C2016 LB 2016 － 2000 CB 2016 CB C2016 LB 2012 LB C2012 LB R2012 － 3000 CB 2012 CB C2012 CB L2012 4000 － LB 1608 4000 － LBMF1608 － 3000 CBMF1608 ②Tape material ●Embossed tape Top tape Chip Filled Sprocket hole Base tape Chip cavity Chip ●Card board carrier tape Top tape Base tape Chip Filled Sprocket hole Bottom tape Chip cavity Chip ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01

③Taping Dimensions ●Embossed Tape （0.315 inches wide） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） A B 3.5±0.05(0.138±0.002) 8.0±0.30.315±0.012) ( F 4.0±0.1 (0.157±0.004) 2.0±0.1 (0.079±0.004) Chip cavity Insertion pitch Tape thickness Type A B F T K 1.75±0.1 2.1±0.1 4.0±0.1 0.3±0.05 1.9max. LBM2016 （0.069±0.004） （0.083±0.004） （0.157±0.004） （0.012±0.002） （0.075max.） LB C3225 2.8±0.1 3.5±0.1 4.0±0.1 0.3±0.05 4.0max. CB C3225 （0.110±0.004） （0.138±0.004） （0.157±0.004） （0.012±0.002） （0.157max.） 2.1±0.1 3.5±0.1 4.0±0.1 0.3±0.05 2.2max. LB 3218 （0.083±0.004） （0.138±0.004） （0.157±0.004） （0.012±0.002） （0.087max.） LB 2518 CB 2518 2.15±0.1 2.7±0.1 4.0±0.1 0.3±0.05 2.2max. LB C2518 （0.085±0.004） （0.106±0.004） （0.157±0.004） （0.012±0.002） （0.087max.） CB C2518 LB R2518 LB 2016 CB 2016 1.75±0.1 2.1±0.1 4.0±0.1 0.3±0.05 1.9max. LB C2016 （0.069±0.004） （0.083±0.004） （0.157±0.004） （0.012±0.002） （0.075max.） CB C2016 LB 2012 CB 2012 1.45±0.1 2.25±0.1 4.0±0.1 0.25±0.05 1.45max. LB C2012 （0.057±0.004） （0.089±0.004） （0.157±0.004） （0.010±0.002） （0.057max.） CB C2012 LB R2012 LBMF1608 1.1±0.1 1.9±0.1 4.0±0.1 0.25±0.05 1.2max. CBMF1608 （0.043±0.004） （0.075±0.004） （0.157±0.004） （0.010±0.002） （0.047max.） Unit：mm（inch） ●Card board carrier tape（0.315 inches wide） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） T A B 3.5±0.05(0.138±0.002) 8.0±0.30.315±0.012) ( F 4.0±0.1 (0.157±0.004) 2.0±0.1 (0.079±0.004) Chip cavity Insertion pitch Tape thickness Type A B F T 1.55±0.1 2.3±0.1 4.0±0.1 1.1max. CB L2012 （0.061±0.004） （0.091±0.004） （0.157±0.004） （0.043max.） 1.0±0.1 1.8±0.1 4.0±0.1 1.1max. LB 1608 （0.039±0.004） （0.071±0.004） （0.157±0.004） （0.043max.） Unit：mm（inch） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01

④Leader and Blank Portion ⑤Reel Size ⑥Top Tape Strength The top tape requires a peel-off force 0.2 to 0.7N in the direction of the arrow as illustrated below. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01

WIRE-WOUND CHIP INDUCTORS (LB SERIES), WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES), WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) ■RELIABILITY DATA 1.Operating temperature Range LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series －40～＋105℃（Including self-generated heat） LBM Series 2. Storage Temperature Range（after soldering） LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series －40～＋85℃ LBM Series Test Methods and LB, CB Series： Remarks Please refer the term of "7. storage conditions" in precautions. 3.Rated Current LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series 4.Inductance LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series LB・LBC・LBR・CB・CBC・CBL・LBMF・CBMF・LBM Series Test Methods and Measuring equipment ：LCR Mater（HP4285A or its equivalent） Remarks Measuring frequency : Specified frequency 5.Q LB, LBC, LBR, LBMF Series － Specified Value CB, CBC, CBL, CBMF Series LBM Series Within the specified tolerance Test Methods and LBM Series Remarks Measuring equipment : LCR Mater（HP4285A or its equivalent） Measuring frequency : Specified frequency 6.DC Resisitance LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series Test Methods and Measuring equipment : DC Ohmmeter （HIOKI 3227 or its equivalent） Remarks 7.Self-Resonant Frequency LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series Test Methods and Measuring equipment : Impedance analyzer （HP4291A or its equivalent） Remarks ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01

8.Temperature Characteristic LBM2016 Inductance change : Within±5％ LB1608 LB2012 LBR2012 CB2012 CBL2012 LB2016 CB2016 LB2518 Inductance change : Within±20％ Specified Value LBR2518 CB2518 LBC3225 CBC3225 LBMF1608 CBMF1608 LBC2016 CBC2016 Inductance change : Within±25％ LBC2518 CBC2518 LB3218 LBC2012 CBC2012 Inductance change : Within±35％ Test Methods and Based on the inductance at 20℃ and Measured at the ambient of －40℃～＋85℃. Remarks 9.Rasistance to Flexure of Substrate LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series No damage. LBM Series Warp : 2mm（LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF Series） Test substrate : Glass epoxy-resin substrate Thickness : 0.8mm（LB1608・LBMF1608・CBMF1608） : 1.0mm（Others） Test Methods and Remarks 10.Body Strength LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series No damage. LBM Series LB・LBC・LBR・CB・CBC・CBL・LBM Applied force : 10N Test Methods and Duration : 10sec. Remarks LB1608・LBMF1608・CBMF1608 Applied force : 5N Duration : 10sec. 11.Adhesion of terminal electrode LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series No abnormality. LBM Series LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF Applied force : 10N to X and Y directions Duration : 5 sec. Test Methods and Test substrate : Printed board Remarks LB1608・CBMF1608・LBMF1608 Applied force : 5N to X and Y directions Duration : 5 sec. Test substrate : Printed board ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01

12.Resistance to vibration LB, LBC, LBR, LBMF Series Inductance change : Within±10％ CB, CBC, CBL, CBMF Series No significant abnormality in appearance. Specified Value Inductance change : Within±5％ LBM Series No significant abnormality in appearance. LB・LBR・LBC・CB・CBC・CBL・LBM・LBMF・CBMF： The given sample is soldered to the board and then it is tested depending on the conditions of the following table. Vibration Frequency 10～55Hz Test Methods and Total Amplitude 1.5mm (May not exceed acceleration 196m/s2) Remarks Sweeping Method 10Hz to 55Hz to 10Hz for 1min. X Time Y For 2 hours on each X, Y, and Z axis. Z Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 13.Drop test LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series － LBM Series 14.Solderability LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series At least 90％ of surface of terminal electrode is covered by new LBM Series LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF： Test Methods and Solder temperature : 245±5℃ Remarks Duration : 5±0.5sec Flux : Methanol solution with 25％ of colophony 15.Resistance to soldering LB, LBC, LBR, LBMF Series Inductance change : Within±10％ Specified Value CB, CBC, CBL, CBMF Series LBM Series Inductance change : Within±5％ Test Methods and LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF： Remarks 3 times of reflow oven at 230℃ MIN for 40sec. with peak temperature at 260 ℃ for 5sec. Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 16.Resisitance to solvent LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series － LBM Series Solvent temperature : Room temperature Test Methods and Type of solvent : Isopropyl alcohol Remarks Cleaning conditions : 90s. Immersion and cleaning. 17.Thermal shock LB, LBC, LBR, LBMF Series Inductance change : Within±10％ Specified Value CB, CBC, CBL, CBMF Series No significant abnormality in appearance. LBM Series Test Methods and LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF： Remarks The given sample is soldered to the board and then its Inductance is measured after 100cycles of the following conditions. Conditions of 1 cycle Step Temperature (℃) Duration (min) 1 －40±3 30±3 2 Room temperature Within 3 3 ＋85±2 30±3 4 Room temperature Within 3 Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01

18.Damp heat life test LB, LBC, LBR, LBMF Series Inductance change : Within±10％ Specified Value CB, CBC, CBL, CBMF Series No significant abnormality in appearance. LBM Series Temperature : 60±2℃ Test Methods and Humidity : 90～95％RH Remarks Duration : 1000 hrs Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 19.Loading under damp heat life test LB, LBC, LBR, LBMF Series Inductance change : Within±10％ CB, CBC, CBL, CBMF Series No significant abnormality in appearance. LBM Series Specified Value Test Methods and Temperature : 60±2℃ Remarks Humidity : 90～95％RH Duration : 1000 hrs Applied current : Rated current Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 20.High temperature life test LB, LBC, LBR, LBMF Series － Specified Value CB, CBC, CBL, CBMF Series Inductance change : Within±10％ LBM Series No significant abnormality in appearance. Temperature : 85±2℃ Test Methods and Duration : 1000 hrs Remarks Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 21.Loading at high temperature life test Inductance change : Within±10％ LB, LBC, LBR, LBMF Series （LBC3225 Series : Within±20％） No significant abnormality in appearance. Specified Value CB, CBC, CBL, CBMF Series － LBM Series Temperature : 85±2℃ Test Methods and Duration : 1000 hrs Remarks Applied current : Rated current Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 22.Low temperature life test LB, LBC, LBR, LBMF Series Inductance change : Within±10％ Specified Value CB, CBC, CBL, CBMF Series No significant abnormality in appearance. LBM Series Temperature : －40±2℃ Test Methods and Duration : 1000 hrs Remarks Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 23.Standard condition Standard test conditions LB, LBC, LBR, LBMF Series Unless specified, Ambient temperature is 20±15℃ and the Relative humidity is 65±20％. If there is any doubt about the test results, further Specified Value CB, CBC, CBL, CBMF Series measurement shall be had within the following limits: Ambient Temperature: 20±2℃ Relative humidity: 65±5％ LBM Series Inductance value is based on our standard measurement systems. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01

WIRE-WOUND CHIP INDUCTORS (LB SERIES)， WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES)， WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) ■PRECAUTIONS 1．Circuit Design ◆Operating environment 1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical Precautions equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2．PCB Design ◆Land pattern design Precautions 1. Please contact any of our offices for a land pattern, and refer to a recommended land pattern of a right figure or specifications. PRECAUTIONS 【Recommended Land Patterns】 Technical Surface Mounting considerations ・ Mounting and soldering conditions should be checked beforehand. ・ Applicable soldering process to those products is reflow soldering only. 3．Considerations for automatic placement ◆Adjustment of mounting machine Precautions 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. Technical 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. considerations 4．Soldering ◆Reflow soldering（ LB and CB Types） 1. For reflow soldering with either leaded or lead-free solder, the profile specified in "point for controlling" is recommended. Precautions ◆Recommended conditions for using a soldering iron 1. Put the soldering iron on the land-pattern. Soldering iron's temperature - Below 350℃ Duration-3 seconds or less. The soldering iron should not come in contact with inductor directly. ◆Reflow soldering（ LB and CB Types） 1. Reflow profile Technical considerations ◆Recommended conditions for using a soldering iron 1. Components can be damaged by excessive heat where soldering conditions exceed the specified range. 5．Cleaning ◆Cleaning conditions Precautions Washing by supersonic waves shall be avoided. Technical ◆Cleaning conditions considerations If washed by supersonic waves, the products might be broken. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_prec_e-E06R01

6．Handling ◆Handling 1. Keep the inductors away from all magnets and magnetic objects. ◆Breakaway PC boards（ splitting along perforations） 1. When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the Precautions board. 2. Board separation should not be done manually, but by using the appropriate devices. ◆Mechanical considerations 1. Please do not give the inductors any excessive mechanical shocks. ◆Handling 1. There is a case that a characteristic varies with magnetic influence. Technical ◆Breakaway PC boards（ splitting along perforations） considerations 1. Planning pattern configurations and the position of products should be carefully performed to minimize stress. ◆Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 7．Storage conditions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. ・ Recommended conditions Ambient temperature : 0～40℃ Precautions Humidity : Below 70% RH ・ The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, product should be used within 6 months from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. ◆Storage Technical 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes considerations and deterioration of taping/packaging materials may take place. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_prec_e-E06R01

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: T aiyo Yuden: LB1608T1R0M LB1608T2R2M LB1608T4R7M LB1608T8R2M LB2012T100K LB2012T100KR LB2012T100M LB2012T100MR LB2012T101K LB2012T101M LB2012T150K LB2012T1R0M LB2012T220K LB2012T220M LB2012T2R2M LB2012T3R3M LB2012T470K LB2012T470M LB2012T4R7M LB2012T680K LB2012T6R8M LB2016T100K LB2016T100M LB2016T101K LB2016T101M LB2016T150K LB2016T150M LB2016T1R0M LB2016T1R5M LB2016T220K LB2016T220M LB2016T2R2M LB2016T330K LB2016T330M LB2016T3R3M LB2016T470K LB2016T470M LB2016T4R7M LB2016T680K LB2016T680M LB2016T6R8M LB2518T100K LB2518T100M LB2518T101K LB2518T101M LB2518T102K LB2518T102M LB2518T150K LB2518T150M LB2518T151K LB2518T151M LB2518T1R0M LB2518T1R5M LB2518T220K LB2518T220M LB2518T221K LB2518T221M LB2518T2R2M LB2518T330K LB2518T330M LB2518T331K LB2518T331M LB2518T3R3M LB2518T470K LB2518T470M LB2518T471K LB2518T471M LB2518T4R7M LB2518T680K LB2518T680M LB2518T681K LB2518T681M LB2518T6R8M LB3218T100K LB3218T100M LB3218T101K LB3218T101M LB3218T102K LB3218T102M LB3218T150K LB3218T150M LB3218T151K LB3218T151M LB3218T1R0M LB3218T1R5M LB3218T220K LB3218T220M LB3218T221K LB3218T221M LB3218T2R2M LB3218T330K LB3218T330M LB3218T331K LB3218T331M LB3218T3R3M LB3218T470K LB3218T470M LB3218T471K LB3218T471M LB3218T4R7M