[ For General Electronic Equipment Notice for TAIYO YUDEN Products (General Environment) ] Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product information in this catalog is as of October 2017. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or use of our products. Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or equipment incorporating our products, which are caused under the conditions other than those specified in this catalog or individual product specification sheets. ■ Please contact TAIYO YUDEN for further details of product specifications as the individual product specification sheets are available. ■ Please conduct validation and verification of our products in actual condition of mounting and operating environment before using our products. ■ The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office equipment, information and communication equipment including, without limitation, mobile phone, and PC) and medical equipment classified as Class I or II by IMDRF. Please be sure to contact TAIYO YUDEN for further information before using the products for any equipment which may directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation, automotive powertrain control system, train control system, and ship control system, traffic signal equipment, disaster prevention equipment, medical equipment classified as Class III by IMDRF, highly public information network equipment including, without limitation, telephone exchange, and base station). Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g., aerospace equipment, aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control equipment, undersea equipment, military equipment). *Note: There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g., in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN. Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment. When our products are used even for high safety and/or reliability-required devices or circuits of general electronic equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to install a protection circuit as necessary. Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above. ■ Information contained in this catalog is intended to convey examples of typical performances and/or applications of our products and is not intended to make any warranty with respect to the intellectual property rights or any other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights. ■ Please note that the scope of warranty for our products is limited to the delivered our products themselves and TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products. Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in accordance with such agreement. ■ The contents of this catalog are applicable to our products which are purchased from our sales offices or authorized distributors (hereinafter“ TAIYO YUDEN’s official sales channel”). Please note that the contents of this catalog are not applicable to our products purchased from any seller other than TAIYO YUDEN’s official sales channel. ■ Caution for Export Some of our products listed in this catalog may require specific procedures for export according to“ U.S. Export Administration Regulations”,“ Foreign Exchange and Foreign Trade Control Law” of Japan, and other applicable regulations. Should you have any questions on this matter, please contact our sales staff. 18

WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES（LB SERIES M TYPE） REFLOW REFLOW ■PARTS NUMBER * Operating Temp.：-40～+105℃（Including self-generated heat） L B M 2 0 1 6 T 1 0 0 J △ △＝Blank space ① ② ③ ④ ⑤ ⑥ ①Series name ④Nominal inductance Code Series name Code Nominal inductance［μH］ LBM Wound chip inductor for signal line （example） R12 0.12 ②Dimensions（L×W） 1R0 1.0 Code Dimensions（L×W）［mm］ 100 10 2016 2.0×1.6 101 100 IN ※R＝Decimal point D U ③Packaging C Code Packaging ⑤Inductance tolerance T T Taping Code Inductance tolerance O J ±5％ R S ／ ⑥Internal code S T A N D ■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY A R D W Recommended Land Patterns L Surface Mounting IN ・Mounting and soldering conditions should be checked beforehand. C D T ・Applicable soldering process to these products is reflow soldering only. U C Type A B C T e LBM2016 0.6 1.0 1.8 O Unit：mm A B A R S Standard quantity ［pcs］ Type L W T e Paper tape Embossed tape 2.0±0.2 1.6±0.2 1.6±0.2 0.5±0.2 LBM2016 － 2000 （0.08±0.008） （0.063±0.008） （0.063±0.008） （0.02±0.008） Unit：mm（inch） i_wound_LBM_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 18 91

■PARTS NUMBER ●LBM2016 type Self-resonant Measuring Nominal inductance Q DC Resistance Rated current Parts number EHS Inductance tolerance frequency frequency ［μH］ （min.） ［Ω］（±30％） ［mA］（max.） ［MHｚ］（min.） ［MHz］ LBM 2016TR12J RoHS 0.12 ±5％ 30 600 0.13 610 25.2 LBM 2016TR15J RoHS 0.15 ±5％ 30 550 0.15 570 25.2 LBM 2016TR18J RoHS 0.18 ±5％ 30 500 0.15 560 25.2 LBM 2016TR22J RoHS 0.22 ±5％ 30 450 0.20 520 25.2 LBM 2016TR27J RoHS 0.27 ±5％ 30 425 0.21 510 25.2 LBM 2016TR33J RoHS 0.33 ±5％ 30 400 0.21 490 25.2 LBM 2016TR39J RoHS 0.39 ±5％ 30 375 0.26 440 25.2 LBM 2016TR47J RoHS 0.47 ±5％ 30 350 0.26 430 25.2 LBM 2016TR56J RoHS 0.56 ±5％ 30 300 0.29 410 25.2 LBM 2016TR68J RoHS 0.68 ±5％ 30 270 0.32 400 25.2 LBM 2016TR82J RoHS 0.82 ±5％ 30 250 0.34 390 25.2 LBM 2016T1R0J RoHS 1.0 ±5％ 30 220 0.38 385 7.96 LBM 2016T1R2J RoHS 1.2 ±5％ 30 180 0.41 370 7.96 LBM 2016T1R5J RoHS 1.5 ±5％ 30 135 0.47 350 7.96 LBM 2016T1R8J RoHS 1.8 ±5％ 30 100 0.48 345 7.96 IN LBM 2016T2R2J RoHS 2.2 ±5％ 30 75 0.54 340 7.96 LBM 2016T2R7J RoHS 2.7 ±5％ 30 55 0.59 310 7.96 D LBM 2016T3R3J RoHS 3.3 ±5％ 30 48 0.68 290 7.96 U LBM 2016T3R9J RoHS 3.9 ±5％ 30 43 0.74 275 7.96 C LBM 2016T4R7J RoHS 4.7 ±5％ 30 40 0.78 270 7.96 T O LBM 2016T5R6J RoHS 5.6 ±5％ 25 36 0.88 255 7.96 LBM 2016T6R8J RoHS 6.8 ±5％ 25 33 0.97 240 7.96 R S LBM 2016T8R2J RoHS 8.2 ±5％ 25 30 1.1 225 7.96 ／ LBM 2016T100J RoHS 10 ±5％ 25 27 1.2 215 2.52 S LBM 2016T120J RoHS 12 ±5％ 25 23 1.4 200 2.52 T LBM 2016T150J RoHS 15 ±5％ 25 20 1.5 190 2.52 A LBM 2016T180J RoHS 18 ±5％ 25 18 2.5 150 2.52 N LBM 2016T220J RoHS 22 ±5％ 25 17 2.8 140 2.52 D LBM 2016T270J RoHS 27 ±5％ 25 16 3.2 130 2.52 A LBM 2016T330J RoHS 33 ±5％ 25 15 3.6 125 2.52 R LBM 2016T390J RoHS 39 ±5％ 20 14 3.9 120 2.52 D LBM 2016T470J RoHS 47 ±5％ 20 13 4.1 115 2.52 IN LBM 2016T560J RoHS 56 ±5％ 20 12 5.9 95 2.52 LBM 2016T680J RoHS 68 ±5％ 20 11 7.0 90 2.52 D LBM 2016T820J RoHS 82 ±5％ 20 10 7.7 85 2.52 U LBM 2016T101J RoHS 100 ±5％ 15 9.0 8.0 80 0.796 C LBM 2016T151J RoHS 150 ±5％ 15 6.5 13.5 69 0.796 T O LBM 2016T181J RoHS 180 ±5％ 15 6.0 15 67 0.796 R LBM 2016T221J RoHS 220 ±5％ 15 5.5 18 65 0.796 S ※）Rated Current : The maximum DC value having inductance decrease within 10 % and temperature increase within 20 degC by the application of DC bias. i_wound_LBM_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 92 18

WIRE-WOUND CHIP INDUCTORS (LB SERIES)， WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES)， WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) ■PACKAGING ①Minimum Quantity Standard Quantity ［pcs］ Type Paper Tape Embossed Tape LB C3225 － 1000 CB C3225 LB 3218 － 2000 LB R2518 LB C2518 LB 2518 － 2000 CB 2518 CB C2518 LBM2016 LB C2016 LB 2016 － 2000 CB 2016 CB C2016 LB 2012 LB C2012 LB R2012 － 3000 CB 2012 CB C2012 CB L2012 4000 － LB 1608 4000 － LBMF1608 － 3000 CBMF1608 ②Tape material ●Embossed tape Top tape Chip Filled Sprocket hole Base tape Chip cavity Chip ●Card board carrier tape Top tape Base tape Chip Filled Sprocket hole Bottom tape Chip cavity Chip ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01

③Taping Dimensions ●Embossed Tape （0.315 inches wide） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） A B 3.5±0.05(0.138±0.002) 8.0±0.30.315±0.012) ( F 4.0±0.1 (0.157±0.004) 2.0±0.1 (0.079±0.004) Chip cavity Insertion pitch Tape thickness Type A B F T K 1.75±0.1 2.1±0.1 4.0±0.1 0.3±0.05 1.9max. LBM2016 （0.069±0.004） （0.083±0.004） （0.157±0.004） （0.012±0.002） （0.075max.） LB C3225 2.8±0.1 3.5±0.1 4.0±0.1 0.3±0.05 4.0max. CB C3225 （0.110±0.004） （0.138±0.004） （0.157±0.004） （0.012±0.002） （0.157max.） 2.1±0.1 3.5±0.1 4.0±0.1 0.3±0.05 2.2max. LB 3218 （0.083±0.004） （0.138±0.004） （0.157±0.004） （0.012±0.002） （0.087max.） LB 2518 CB 2518 2.15±0.1 2.7±0.1 4.0±0.1 0.3±0.05 2.2max. LB C2518 （0.085±0.004） （0.106±0.004） （0.157±0.004） （0.012±0.002） （0.087max.） CB C2518 LB R2518 LB 2016 CB 2016 1.75±0.1 2.1±0.1 4.0±0.1 0.3±0.05 1.9max. LB C2016 （0.069±0.004） （0.083±0.004） （0.157±0.004） （0.012±0.002） （0.075max.） CB C2016 LB 2012 CB 2012 1.45±0.1 2.25±0.1 4.0±0.1 0.25±0.05 1.45max. LB C2012 （0.057±0.004） （0.089±0.004） （0.157±0.004） （0.010±0.002） （0.057max.） CB C2012 LB R2012 LBMF1608 1.1±0.1 1.9±0.1 4.0±0.1 0.25±0.05 1.2max. CBMF1608 （0.043±0.004） （0.075±0.004） （0.157±0.004） （0.010±0.002） （0.047max.） Unit：mm（inch） ●Card board carrier tape（0.315 inches wide） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） T A B 3.5±0.05(0.138±0.002) 8.0±0.30.315±0.012) ( F 4.0±0.1 (0.157±0.004) 2.0±0.1 (0.079±0.004) Chip cavity Insertion pitch Tape thickness Type A B F T 1.55±0.1 2.3±0.1 4.0±0.1 1.1max. CB L2012 （0.061±0.004） （0.091±0.004） （0.157±0.004） （0.043max.） 1.0±0.1 1.8±0.1 4.0±0.1 1.1max. LB 1608 （0.039±0.004） （0.071±0.004） （0.157±0.004） （0.043max.） Unit：mm（inch） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01

④Leader and Blank Portion ⑤Reel Size ⑥Top Tape Strength The top tape requires a peel-off force 0.2 to 0.7N in the direction of the arrow as illustrated below. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01

WIRE-WOUND CHIP INDUCTORS (LB SERIES), WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES), WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) ■RELIABILITY DATA 1.Operating temperature Range LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series －40～＋105℃（Including self-generated heat） LBM Series 2. Storage Temperature Range（after soldering） LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series －40～＋85℃ LBM Series Test Methods and LB, CB Series： Remarks Please refer the term of "7. storage conditions" in precautions. 3.Rated Current LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series 4.Inductance LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series LB・LBC・LBR・CB・CBC・CBL・LBMF・CBMF・LBM Series Test Methods and Measuring equipment ：LCR Mater（HP4285A or its equivalent） Remarks Measuring frequency : Specified frequency 5.Q LB, LBC, LBR, LBMF Series － Specified Value CB, CBC, CBL, CBMF Series LBM Series Within the specified tolerance Test Methods and LBM Series Remarks Measuring equipment : LCR Mater（HP4285A or its equivalent） Measuring frequency : Specified frequency 6.DC Resisitance LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series Test Methods and Measuring equipment : DC Ohmmeter （HIOKI 3227 or its equivalent） Remarks 7.Self-Resonant Frequency LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series Test Methods and Measuring equipment : Impedance analyzer （HP4291A or its equivalent） Remarks ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01

8.Temperature Characteristic LBM2016 Inductance change : Within±5％ LB1608 LB2012 LBR2012 CB2012 CBL2012 LB2016 CB2016 LB2518 Inductance change : Within±20％ Specified Value LBR2518 CB2518 LBC3225 CBC3225 LBMF1608 CBMF1608 LBC2016 CBC2016 Inductance change : Within±25％ LBC2518 CBC2518 LB3218 LBC2012 CBC2012 Inductance change : Within±35％ Test Methods and Based on the inductance at 20℃ and Measured at the ambient of －40℃～＋85℃. Remarks 9.Rasistance to Flexure of Substrate LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series No damage. LBM Series Warp : 2mm（LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF Series） Test substrate : Glass epoxy-resin substrate Thickness : 0.8mm（LB1608・LBMF1608・CBMF1608） : 1.0mm（Others） Test Methods and Remarks 10.Body Strength LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series No damage. LBM Series LB・LBC・LBR・CB・CBC・CBL・LBM Applied force : 10N Test Methods and Duration : 10sec. Remarks LB1608・LBMF1608・CBMF1608 Applied force : 5N Duration : 10sec. 11.Adhesion of terminal electrode LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series No abnormality. LBM Series LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF Applied force : 10N to X and Y directions Duration : 5 sec. Test Methods and Test substrate : Printed board Remarks LB1608・CBMF1608・LBMF1608 Applied force : 5N to X and Y directions Duration : 5 sec. Test substrate : Printed board ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01

12.Resistance to vibration LB, LBC, LBR, LBMF Series Inductance change : Within±10％ CB, CBC, CBL, CBMF Series No significant abnormality in appearance. Specified Value Inductance change : Within±5％ LBM Series No significant abnormality in appearance. LB・LBR・LBC・CB・CBC・CBL・LBM・LBMF・CBMF： The given sample is soldered to the board and then it is tested depending on the conditions of the following table. Vibration Frequency 10～55Hz Test Methods and Total Amplitude 1.5mm (May not exceed acceleration 196m/s2) Remarks Sweeping Method 10Hz to 55Hz to 10Hz for 1min. X Time Y For 2 hours on each X, Y, and Z axis. Z Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 13.Drop test LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series － LBM Series 14.Solderability LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series At least 90％ of surface of terminal electrode is covered by new LBM Series LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF： Test Methods and Solder temperature : 245±5℃ Remarks Duration : 5±0.5sec Flux : Methanol solution with 25％ of colophony 15.Resistance to soldering LB, LBC, LBR, LBMF Series Inductance change : Within±10％ Specified Value CB, CBC, CBL, CBMF Series LBM Series Inductance change : Within±5％ Test Methods and LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF： Remarks 3 times of reflow oven at 230℃ MIN for 40sec. with peak temperature at 260 ℃ for 5sec. Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 16.Resisitance to solvent LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series － LBM Series Solvent temperature : Room temperature Test Methods and Type of solvent : Isopropyl alcohol Remarks Cleaning conditions : 90s. Immersion and cleaning. 17.Thermal shock LB, LBC, LBR, LBMF Series Inductance change : Within±10％ Specified Value CB, CBC, CBL, CBMF Series No significant abnormality in appearance. LBM Series Test Methods and LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF： Remarks The given sample is soldered to the board and then its Inductance is measured after 100cycles of the following conditions. Conditions of 1 cycle Step Temperature (℃) Duration (min) 1 －40±3 30±3 2 Room temperature Within 3 3 ＋85±2 30±3 4 Room temperature Within 3 Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01

18.Damp heat life test LB, LBC, LBR, LBMF Series Inductance change : Within±10％ Specified Value CB, CBC, CBL, CBMF Series No significant abnormality in appearance. LBM Series Temperature : 60±2℃ Test Methods and Humidity : 90～95％RH Remarks Duration : 1000 hrs Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 19.Loading under damp heat life test LB, LBC, LBR, LBMF Series Inductance change : Within±10％ CB, CBC, CBL, CBMF Series No significant abnormality in appearance. LBM Series Specified Value Test Methods and Temperature : 60±2℃ Remarks Humidity : 90～95％RH Duration : 1000 hrs Applied current : Rated current Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 20.High temperature life test LB, LBC, LBR, LBMF Series － Specified Value CB, CBC, CBL, CBMF Series Inductance change : Within±10％ LBM Series No significant abnormality in appearance. Temperature : 85±2℃ Test Methods and Duration : 1000 hrs Remarks Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 21.Loading at high temperature life test Inductance change : Within±10％ LB, LBC, LBR, LBMF Series （LBC3225 Series : Within±20％） No significant abnormality in appearance. Specified Value CB, CBC, CBL, CBMF Series － LBM Series Temperature : 85±2℃ Test Methods and Duration : 1000 hrs Remarks Applied current : Rated current Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 22.Low temperature life test LB, LBC, LBR, LBMF Series Inductance change : Within±10％ Specified Value CB, CBC, CBL, CBMF Series No significant abnormality in appearance. LBM Series Temperature : －40±2℃ Test Methods and Duration : 1000 hrs Remarks Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 23.Standard condition Standard test conditions LB, LBC, LBR, LBMF Series Unless specified, Ambient temperature is 20±15℃ and the Relative humidity is 65±20％. If there is any doubt about the test results, further Specified Value CB, CBC, CBL, CBMF Series measurement shall be had within the following limits: Ambient Temperature: 20±2℃ Relative humidity: 65±5％ LBM Series Inductance value is based on our standard measurement systems. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01

WIRE-WOUND CHIP INDUCTORS (LB SERIES)， WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES)， WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) ■PRECAUTIONS 1．Circuit Design ◆Operating environment 1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical Precautions equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2．PCB Design ◆Land pattern design Precautions 1. Please contact any of our offices for a land pattern, and refer to a recommended land pattern of a right figure or specifications. PRECAUTIONS 【Recommended Land Patterns】 Technical Surface Mounting considerations ・ Mounting and soldering conditions should be checked beforehand. ・ Applicable soldering process to those products is reflow soldering only. 3．Considerations for automatic placement ◆Adjustment of mounting machine Precautions 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. Technical 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. considerations 4．Soldering ◆Reflow soldering（ LB and CB Types） 1. For reflow soldering with either leaded or lead-free solder, the profile specified in "point for controlling" is recommended. Precautions ◆Recommended conditions for using a soldering iron 1. Put the soldering iron on the land-pattern. Soldering iron's temperature - Below 350℃ Duration-3 seconds or less. The soldering iron should not come in contact with inductor directly. ◆Reflow soldering（ LB and CB Types） 1. Reflow profile Technical considerations ◆Recommended conditions for using a soldering iron 1. Components can be damaged by excessive heat where soldering conditions exceed the specified range. 5．Cleaning ◆Cleaning conditions Precautions Washing by supersonic waves shall be avoided. Technical ◆Cleaning conditions considerations If washed by supersonic waves, the products might be broken. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_prec_e-E06R01

6．Handling ◆Handling 1. Keep the inductors away from all magnets and magnetic objects. ◆Breakaway PC boards（ splitting along perforations） 1. When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the Precautions board. 2. Board separation should not be done manually, but by using the appropriate devices. ◆Mechanical considerations 1. Please do not give the inductors any excessive mechanical shocks. ◆Handling 1. There is a case that a characteristic varies with magnetic influence. Technical ◆Breakaway PC boards（ splitting along perforations） considerations 1. Planning pattern configurations and the position of products should be carefully performed to minimize stress. ◆Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 7．Storage conditions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. ・ Recommended conditions Ambient temperature : 0～40℃ Precautions Humidity : Below 70% RH ・ The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, product should be used within 6 months from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. ◆Storage Technical 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes considerations and deterioration of taping/packaging materials may take place. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_prec_e-E06R01

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: T aiyo Yuden: LBM2016T100J LBM2016T101J LBM2016T120J LBM2016T150J LBM2016T180J LBM2016T1R0J LBM2016T1R2J LBM2016T1R5J LBM2016T1R8J LBM2016T220J LBM2016T270J LBM2016T2R2J LBM2016T2R7J LBM2016T330J LBM2016T390J LBM2016T3R3J LBM2016T3R9J LBM2016T470J LBM2016T4R7J LBM2016T560J LBM2016T5R6J LBM2016T680J LBM2016T6R8J LBM2016T820J LBM2016T8R2J LBM2016TR12J LBM2016TR15J LBM2016TR18J LBM2016TR22J LBM2016TR27J LBM2016TR33J LBM2016TR39J LBM2016TR47J LBM2016TR56J LBM2016TR68J LBM2016TR82J