Series JW High Inrush 10 & 16 Amp Rockers es General Specifications gl g o T Electrical Capacity (Resistive Load) s ker B Power Level: 10A @ 125/250V AC for JWM & JWMW models; 10A @ 30V DC for JWMW; c o 16A @ 125/250V AC for JWL & JWLW models; 5A @ 72V DC for telecommunication applications R Other Ratings ns Contact Resistance: 10 milliohms maximum for JWM & JWMW; 20 milliohms maximum for JWL & JWLW o utt Insulation Resistance: 1,000 megohms minimum @ 500V DC b h Dielectric Strength: 2,000V AC minimum between contacts for 1 minute minimum; s u P 4,000V AC minimum between contacts & case for 1 minute minimum B Mechanical Life: 25,000 operations minimum P d Electrical Life: 25,000 operations minimum e nat Nominal Operating Force: JWM & JWMW Single Pole 3.92N & Double Pole 7.84N umi JWL Single Pole 5.00N & Double Pole 10.00N; JWLW Double Pole 10.00N Ill Angle of Throw: 26° e bl a Materials & Finishes m am Rocker: Polyphenylene ether (UL94V-0) Contacts: JWM & JWMW: Silver alloy with silver plating ogr Housing/Frame & Barrier: Polyamide (UL94V-0) JWL & JWLW: Silver alloy plus copper with Pr Interior Seal for JWM & JWL: Polyphenylene sulfide (UL94V-0) silver plating s Case/Base: Melamine (UL94V-0) Terminals: Brass with silver plating k c o Environmental Data yl e K Operating Temperature Range: –25°C through +70°C (–13°F through +158°F) for JWM & JWL; –25°C through +85°C (–13°F through +185°F) for panel seal JWMW & JWLW models Humidity: 90 ~ 95% humidity for 96 hours @ 40°C (104°F) s e ari Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning ot in 1 minute; 3 right angled directions for 2 hours R Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Sealing: IP67 of IEC60529 standard for panel seal JWMW & JWLW models; dust resistant inner seal for others es Installation d Sli Soldering Time & Temperature: Manual Soldering: See Profile A in Supplement section. Standards & Certifications Flammability Standards: UL94V-0 for rocker, housing, seal & case/base of JWL, JWM, JWMW & JWLW models s actile TV Ratings for UL & CSA: JWM (TV-S5te) aOdvye Srltoaated C Tuersrt e n@t (1rm20s)V 7 A.5CA ;f oMr i5n0im oupme rIantriuosnhs :Current (peak) 111A. T JWM (TV-5) Endurance Test @ 120V AC for 25,000 operations: Steady State Current (rms) 5A; Minimum Inrush Current (peak) 78A. JWL (TV-8) Overload Test @ 120V AC for 50 operations: Tilt Steady State Current (rms) 12A; Minimum Inrush Current (peak) 163A. JWL (TV-8) Endurance Test @ 120V AC for 25,000 operations: Steady State Current (rms) 8A; Minimum Inrush Current (peak) 117A. UL: File No. E44145 h c JWM & JWMW models recognized at 10A @ 250V AC. u o T JWMW recognized at 10A @ 30V DC. JWL & JWLW models recognized at 16A @ 250V AC; JWL at 5A @ 72V DC. s Models below recognized only when ordered with marking on switch. or at JWMW: add “/U” to end of part number to order UL mark on switch; add “/CUL” to end of part c di number to order cULus mark on switch. n I JWL: add “/U-DC” to end of part number to request UL rating on DC rated switch. s CSA: File No. 023535_0_000 e ori JWM & JWMW models certified at 10A @ 250V AC; JWL models certified at 16A @ 250V AC s es VDE: License No. 115674 c Ac JWM models approved at steady state 5A, inrush 80A, resistive 10A, & motor load 6A all at 250V AC; JWL models approved at steady state inrush 128A, resistive 16A, & motor load 8A ent all at 250V AC. m e Note: JWM & JWL Double Pole, Single Throw models approved only with the international pl p ON-OFF symbols on the actuator. u S B40 www.nkkswitches.com 8/3/17

Series JW High Inrush 10 & 16 Amp Rockers Distinctive Characteristics es gl g o T s Industry’s first molded rocker with TV rating. Designed to handle large inrush current, B ker c with high electrical capacity of 10 and 16 Amps. JWM models certified for TV-5 rating Ro and JWL models for TV-8 rating. s n o utt b JWMW and JWLW panel seal versions meet IP67 of h s u IEC60529 Standards (similar to NEMA 4 and 6). P B P d e Prominent external insulating barriers increase nat mi insulation resistance and dielectric strength. u Ill e bl a m Uniquely constructed to break light m a contact welds. ogr Pr s k Increased electrical life with specially c o yl designed plate to minimize contact bounce. e K Constructed for dust resistance with interior es ari cover between actuator and contact area. ot R Terminals are molded in and epoxy sealed to s e lock out flux, dust, and other contaminants. Slid Solder lug/quick connect terminals can be used s e with connector. ctil a T Housing and case of heat resistant resin meet UL94V-0 standard. Tilt Actual Size JWM h c u o T s or at c di n I s e ori s s e c c A nt e m e pl p u S www.nkkswitches.com B41

Series JW High Inrush 10 & 16 Amp Rockers s e gl TYPICAL SWITCH ORDERING EXAMPLE g o T s JW LW 2 1 R A 1 A ker B c o R s n o utt Ratings Housing Colors b sh M 10A @ 125/250V AC Barrier Types A Black u P Panel Seal R No Barrier B Ivory B MW d P 10A @ 125/250V AC B With Barrier H Gray e minat L 16A @ 125/250V AC Note: JWMW & JWLW Note: JWMW & JWLW u Panel Seal combine with code R only. available with black only. Ill LW 16A @ 125/250V AC e bl a m m a gr Cap Colors Barrier Colors o Pr Poles A Black A Black cks 1 SPST B Ivory B Ivory o SPDT eyl C Red H Gray K DPST 2 DPDT H Gray s Notes: Note: JWMW & JWLW avail- e ari DPST must have international able with black or red caps only. Rot ON-OFF symbols for VDE approval. JWLW available in DPST & s DPDT only. Inscription e d Sli Orientation No No Inscription IMPORTANT: Code es Circuits 1 Horizontal Standard markings for JWM & JWL: Tactil 1 ON NONE OFF 2 Vertical TSVta nRdaatirndg ,m UaLr,k CinSgA f o&r JVWDELW. : cULus. 2 ON NONE ON Specific models, ratings & ordering These are inscriptions for instructions for international approvals Single Throw models only. are noted on General Specifications page. Tilt h DESCRIPTION FOR TYPICAL ORDERING EXAMPLE c u o T JWLW21RA1A s Black Rocker Cap with or at International ON-OFF Symbols c di in Horizontal Orientation n I s e ori Black Housing s s e c c DPST A ON-NONE-OFF Circuit 16A @ 125/250V AC nt e m e pl p u S B42 www.nkkswitches.com

Series JW High Inrush 10 & 16 Amp Rockers s e RATINGS gl g o T M MW Power Level 10A @ 125/250V AC Panel Seal Power Level 10A @ 125/250V AC s B ker L LW c o Power Level 16A @ 125/250V AC Panel Seal Power Level 16A @ 125/250V AC R POLES & CIRCUITS s n o Rocker Position Connected Terminals Throw & Schematics butt h s Down Center Up Down Center Up Note: Terminal numbers are actually on Pu Pole Model the switch. Actuator positions oriented B with switch part number facing front. d P e JWM11 1 (COM) minat SP JWMW11 ON NONE OFF 1-1b OPEN OPEN SPST u JWL11 1b Ill e bl JWM12 1 (COM) ma SP JWMW12 ON NONE ON 1-1b OPEN 1-1a SPDT m a JWL12 1a 1b gr o Pr JWM21 JWMW21 1-1b 1 (COM) 2 s DP JWL21 ON NONE OFF 2-2b OPEN OPEN DPST ock 1b 2b yl JWLW21 e K JWM22 JWMW22 1-1b 1-1a 1 (COM) 2 DP ON NONE ON OPEN DPDT es JWL22 2-2b 2-2a 1a 1b 2a 2b ari JWLW22 ot R BARRIER TYPES & COLORS s e d R B Sli No Barrier With Barrier s e ctil a T JWM JWL JWM JWL Tilt Barrier type designates that either AT217 (for JWM) or No-barrier type has a flat flange AT218 (for JWL) is factory assembled. which is an integral part of the switch. Dimensions for barriers are shown in the Accessories section. h c u o JWMW and JWLW panel seal devices have exterior seal Barrier Colors T A B H of acrylonitrile butadiene rubber covering the flange. Available: Black Ivory Gray s Flange/Housing Material: Polyamide Finish: Matte Barrier Material: Polyamide Finish: Matte or at c di CAP COLORS n I s e Cap Colors A B C H ori s Available: Black Ivory Red Gray es c c A Cap Material: Polyphenelene Oxide Rocker cap is an integral part of the switch and not available separately. nt e m Finish: Matte JWMW and JWLW available with black or red caps only. ple p u S www.nkkswitches.com B43

Series JW High Inrush 10 & 16 Amp Rockers s e gl INSCRIPTIONS g o T Inscription for Inscription for No Code 1 2 No Inscription Horizontal Mounting Vertical Mounting s ker B c o R s n o utt b h s u P The IEC symbols for On-Off are supplied with Single Throw models only. B DPST models without inscriptions Orientation of inscription must be selected. P d do not have VDE approval. Inscription Colors: Black ink on Ivory or Gray cap. White ink on Black or Red cap. e at Contact factory for other inscriptions. n mi u Ill e HOUSING bl a m m a gr Colors A B H o Pr Material: Polyamide Available: Black Ivory Gray s k Finish: Matte JWMW and JWLW panel seal models available with black housing only. c o yl e K TERMINALS s e ari Solder Lug/Quick Connect .110” (2.8mm) Solder Lug/Quick Connect .187” (4.75mm) ot R (3.2) Epoxy Seal .126 (7.5) Epoxy Seal (7.5) es JWM & JWMW .295 JWL & JWLW (1.5) R .295 d (0.6) R .059 Sli .024 (2.8) (0.65) R (1.6) .110 .026 (4.75) .063 .187 Thk = (0.5) Thk = (0.8) .020 .031 s e actil PANEL CUTOUTS T Panel Thickness Range Tilt Without Barrier (JWM & JWMW): .039” ~ .157” (1.0mm ~ 4.0mm) (2.944.05) (2.958.04) h With Barrier (JWM): JWM JWMW c u .024” ~ .126” (0.6mm ~ 3.2mm) o T (15.4) (15.4) .606 .606 s or at Panel Thickness Range c di n I Without Barrier (JWL & JWLW): es .039” ~ .157” (1.0mm ~ 4.0mm) (29.5) (30.7) ori 1.161 1.209 ss With Barrier (JWL): cce .024” ~ .126” (0.6mm ~ 3.2mm) JWL JWLW A nt me (20.5) (20.5) e .807 .807 pl p u S B44 www.nkkswitches.com

Series JW High Inrush 10 & 16 Amp Rockers s e TYPICAL SWITCH DIMENSIONS FOR JWM & JWMW gl g o T Single & Double Pole No Barrier • 10 Amp s B ker c o R Part No. .(263.06) (1.559.01) s n o (7.7) Typ 2b 1b butt (.1797.62) 26° .303 ( 2.829.60) 2COM COM1 (12.076.03) Push (16.4) 2a 1a .646 PB d e (0.5) Typ (2.8) Typ at (13.6) (2.0) .020 (6.2) .110 min .535 .079 .244 u (.1780.09) (.2814.56) .(279.55) (.1650.64) Ill e bl a m m JWM11RC1A a gr o Pr Single & Double Pole With Barrier • 10 Amp s k c o yl e K (15.0) Part No. .591 s e ari (7.7) Typ 2b 1b ot (19.6) (25.0) .303 (22.6) 2 1 (30.0) R .772 .984 .890 1.181 COM COM 2a 1a s e d (0.5) Typ Sli (13.6) .020 (2.8) Typ .535 (18.0) (6.2) .110 .709 .244 (22.2) (7.2) (18.9) (7.5) (15.4) .874 .283 .744 .295 .606 s e ctil a JWM11BCA-H T Single & Double Pole Panel Seal • No Barrier • 10 Amp Tilt Part No. (7.0) (15.0) .276 .591 h c u o T (7.7) Typ 2b 1b (.1797.62) 26° .303 ( 2.829.60) 2 1 (12.196.65) COM COM s (16.4) 2a 1a or .646 at c di (0.5) Typ n .020 (2.8) Typ I .110 (13.6) (3.0) (6.2) .535 .118 .244 es (.2812.07) (.2814.56) . 2(79.55) (.1650.46) ori s s e c c JWMW22RCA A nt e Single pole double throw models do not have terminals 2a, 2, & 2b; single throw models do not have 1a & 2a. m e pl p u S www.nkkswitches.com B45

Series JW High Inrush 10 & 16 Amp Rockers s e gl TYPICAL SWITCH DIMENSIONS FOR JWL & JWLW g o T No Barrier • 16 Amp Single & Double Pole s ocker B Part No. .(27.706) ( 2.708.70) R s n utto .(398.86) Typ 22b 1b1 shb (2.946.41) 26° (12.180.02) (13.226.00) Pu (20.2) C2OaM CO1Ma .795 B P d e at (0.8) Typ (4.75) Typ Illumin (.1679.63) (23.0) .(027.09) (24.0) (7.5) .031 ( .2(3905..045)) .187 ble .906 .945 .295 .807 a m m a gr JWL21RC2A Single pole double throw models do not have terminals 2a, 2, & 2b; single throw models do not have 1a & 2a. o Pr s ck With Barrier • 16 Amp Single & Double Pole o yl e K Part No. (20.0) .787 s e ari Rot (9.8) Typ 2b 1b .386 2 1 (24.4) (29.0) (28.0) (35.0) .961 1.142 1.102 1.378 COM COM s 2a 1a e d Sli (17.6) (0.8) Typ (4.75) Typ .693 .031 .187 (23.0) (9.0) es .906 .354 actil (12.07.721) (.83.2151 ) (.2814.43) . 2(79.55) (2.800.57) T JWL11BCA-H Single pole double throw models do not have terminals 2a, 2, & 2b; single throw models do not have 1a & 2a. Tilt Panel Seal • 16 Amp • Inscription Double Pole Single Throw uch Part No. (.73.191) ( 4.1.8775) Typ o (0.8) Typ T .031 s or (9.8) 2b 1b at .386 2 1 ndic (2.946.41) 26° (12.810.02) (13.476.39) I COM COM (20.2) .795 2a 1a s e ori s s e c c A (17.6) (9.0) .693 .354 nt (27.0) (2.7) (21.3) (7.5) (20.0) me 1.063 .106 .839 .295 .787 e ppl JWLW21RA1A u S B46 www.nkkswitches.com

Series JW High Inrush 10 & 16 Amp Rockers s e TYPICAL SWITCH DIMENSIONS FOR JWLW gl g o T Double Pole Double Throw Panel Seal • 16 Amp • No Inscription s Part No. (.73.191) ( 4.1.8775) Typ B cker (0.8) Typ Ro .031 s n o (.93.886) Typ 22b 1b1 butt (2.946.41) 26° (12.810.02) (13.476.39) ush P COM COM (2.709.52) 2a 1a PB d e at n mi u Ill (.1679.63) .(395.04) ble (27.0) (2.7) (21.3) (7.5) (20.0) a 1.063 .106 .839 .295 .787 mm a JWLW22RAA gr o Pr OPTIONAL DUST COVER s k c o yl AT4126 Ke Dust Cover for JWL Rocker When installed, the Dust Cover protects the switch from an environment containing s e small particles and dust. The switch is operable with the Dust Cover in place. ari Rot Materials: Recommended Temperature Range: Lid: Clear Polyvinyl Chloride –10° ~ +70°C (+14°F ~ +158°F) s e d Base: Black Polyamide Loses pliability below 0°C (+32°F) Sli Recommended Panel Thickness: .031” ~ .134” (0.8mm ~ 3.4mm) es ctil a T Assembly Instructions: Tilt 1. Insert bottom of switch through the base until the tabs lock into place. (42.0) 1.654 2. Snap the switch into the panel. h c 3. Seat the lid into the grooves of the base. ou T (.210.62) Groove ors (22.2) (8.6) (33.0) at .874 .339 1.299 c di n Top Side Bottom I s e Lid Switch Base ori s Notes es c c A 1. The dust cover is not for use with JWLW. nt 2. The dust cover cannot be used with the barrier option. Groove me e pl p u S www.nkkswitches.com B47

Series JW High Inrush 10 & 16 Amp Rockers s e gl PRECAUTIONS FOR HANDLING & STORAGE FOR JWMW/LW (PANEL SEAL TYPES) g o T Operating Environment s ker B • Do not install switch where heavy dust collection occurs. Dust build-up under rocker may affect switch actuation. c o R • Do not actuate switch if submerged in water or oil. 30° ns • Installation is not recommended on horizontal surface in an environment where frequent splashing of o utt water may occur. In such an environment, a minimum 30° angle installation is advisable. If there is b h a possibility of freezing, install vertically so no moisture will be retained within switch housing. s u P B Panel Mounting P d Incorrect Correct e at • Before snapping a switch into the panel, align the gasket evenly under bezel of the switch. n mi Illu • When mounting into a panel, apply equal pressure to sides of bezel and insert parallel to panel. e bl • After mounting a switch, be sure there are no gaps between switch and panel. a m Lightly push into panel. m a ogr • After installing into panel, do not apply excessive force. Pr • After panel installation and wiring is completed, do not apply force horizontally s k or vertically from behind panel. c o Clean Edges yl e • Behind the panel, cut area should be squared. If front of panel is painted, do not allow any paint to collect in K corners of cutout to prevent level mounting. s • Avoid reinstalling a switch once it has been mounted in a panel. This may cause deterioration of panel sealability. e ari ot R s e d Sli s e ctil a T Tilt h c u o T s or at c di n I s e ori s s e c c A nt e m e pl p u S B48 www.nkkswitches.com

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: N KK Switches: JWLW21RC2A JWL12BAA-H JWM11RHA JWLW21RA2A JWM22BAA-B JWL21BA2A-B JWL22BAA-H