Series JP Internationally Approved Pushbuttons s e ggl General Specifications o T s er k Electrical Capacity (Resistive Load) c o R Power Level: 10A @ 125/250V AC for JPM models & 16A @ 125/250V AC for JPL models ns Other Ratings o utt C Contact Resistance: 20 milliohms maximum b h Insulation Resistance: 1,000 megohms minimum @ 500V DC s u P Dielectric Strength: 2,000V AC minimum between contacts for 1 minute minimum; B 4,000V AC minimum between contacts & case for 1 minute minimum P ed Mechanical Life: 25,000 operations minimum at n Electrical Life: 25,000 operations minimum mi u Nominal Operating Force: JPM Single Pole 3.53N & Double Pole 6.47N Ill JPL Single Pole 4.51N & Double Pole 9.02 N e abl Contact Timing: Nonshorting (break before make) m m Latchdown: Normal position - flush with barrier; latchdown position - .079” (2.0mm) below normal a gr Travel: Pretravel .059” (1.5mm); Overtravel .071” (1.8mm); Total Travel .130” (3.3mm) o Pr Materials & Finishes s k c Housing/Frame & Barrier: Polyamide (UL94V-0) Movable Contacts: Silver alloy o eyl Interior Seal: Polyphenylene sulfide (UL94V-0) Stationary Contacts: Silver alloy plus copper K Case/Base: Melamine (UL94V-0) Terminals: Brass with silver plating es Environmental Data ari Operating Temp Range: –10°C through +70°C (+14°F through +158°F) ot R Humidity: 90 ~ 95% humidity for 96 hours @ 40°C (104°F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours s de Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Sli Process Seal: Dust resistant inner seal Installation s e Soldering Time & Temp: Manual Soldering: See Profile A in Supplement section. ctil a T Standards & Certifications Flammability Standards: UL94V-0 for housing/frame, barrier, interior seal, & case/base TV Ratings for UL: JPM (TV-5) Overload Test @ 125V AC for 50 operations: Tilt Steady State Current (rms) 7.5A; Minimum Inrush Current (peak) 111A JPM (TV-5) Endurance Test @ 125V AC for 25,000 operations: Steady State Current (rms) 5A; Minimum Inrush Current (peak) 78A JPL (TV-8) Overload Test @ 125V AC for 50 operations: h Steady State Current (rms) 12A; Minimum Inrush Current (peak) 163A c u o JPL (TV-8) Endurance Test @ 125V AC for 25,000 operations: T Steady State Current (rms) 8A; Minimum Inrush Current (peak) 117A UL: File No. E44145 - Recognized only when ordered with marking on switch. ors Add “/U” or “/CUL” before dash in part number to order UL recognized switch. at All JPM models certified at 10A @ 125V AC, TV5 & JPL models at 16A @ 125V AC, TV8. c di n I VDE: License No. 40028887 - Approved only when ordered with marking on switch. s Add “/V” before dash in part number to order VDE approved switch. e ori All JPM models approved at steady state 5A, inrush 80A, resistive 10A, & motor load 6A all at s es 250V AC. c Ac License No. 40039784 All JPL models approved at steady state 8A, inrush 128A, resistive 16A, & motor load 8A all at nt 250V AC. e m e pl p u S C58 www.nkkswitches.com

Series JP Internationally Approved Pushbuttons s e Distinctive Characteristics ggl o T s er k c o Industry’s first molded pushbutton with TV rating. Designed to R handle large inrush current. JPM models certified for TV-5 s rating and JPL models for TV-8 rating. n o C utt b h s u P B Prominent external insulating barriers increase d P e insulation resistance and dielectric strength. at n mi u Ill e bl a m Constructed for dust resistance with m a interior seal of polyphenylene gr o sulfide (PPS) between actuator Pr and contact area. s k c o yl e K Specially designed to break light s e contact welds. ari ot R Snap-action contact mechanism. es d Sli s Terminals are molded in and epoxy e sealed to lock out flux, dust, and actil T other contaminants. Tilt Outer case of heat resistant resin meets UL’s 94V-0 flammability standard. Actual Size JPM h c u o T s or at c di n I s e ori s s e c c A nt e m e pl p u S www.nkkswitches.com C59

Series JP Internationally Approved Pushbuttons s e gl TYPICAL SWITCH ORDERING EXAMPLE g o T s JP M 2 6 B H er k c o R s n o utt C b h Ratings Actuators s u P TV-5 Rated B Flat Cap with Barrier Flange B M P 10A @ 125/250V AC d Plunger with Flat Flange; cap e P at TV-8 Rated not supplied with plunger n L mi 16A @ 125/250V AC u Ill e bl a m m a gr o Pr Poles Circuit Cap Colors 1 SPST 6 OFF ON A Black s k c o 2 DPST (Alternate Action with Latchdown) B Ivory yl e K C Red H Gray s e ari ot R IMPORTANT: Switches are supplied without UL & VDE markings unless specified. es UL recognized only when ordered with marking on the switch. Slid VDE approved only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. s e ctil a T Tilt DESCRIPTION FOR TYPICAL ORDERING EXAMPLE JPM26B-H h c u o T Gray Flat Cap with Barrier Flange s or at c di TV-5 Rated n I 10A @ 125/250V AC s e ori DPST s es OFF-ON Circuit c c A nt e m e pl p u S C60 www.nkkswitches.com

Series JP Internationally Approved Pushbuttons s e RATINGS gl g o T M TV-5 Rated Power Level 10A @ 125/250V AC s er k c o R L TV-8 Rated Power Level 16A @ 125/250V AC s n o Note: See General Specifications page to find complete explanation of TV ratings. C butt h s u P POLES & CIRCUIT B P d e Plunger Position Connected Terminals Throw & Schematics at n mi Normal Down Normal Down Note: Terminal numbers are Illu Pole Model e actually on the switch. bl a m m a JPM16 1 (COM) ogr SP OFF ON OPEN 1-1a SPST Pr JPL16 1a s k c JPM26 1 (COM) 2 ylo DP OFF ON OPEN 1-1a 2-2a DPST e JPL26 1a 2a K s ACTUATORS arie ot R B Flat Cap P Plunger with Barrier Flange with Flat Flange s e d The barrier is an integral part The flange is an integral part Sli of the switch. This housing of the switch. This housing is black, molded polyamide is black, molded polyamide matte finish material. matte finish material. s e ctil a Cap details below. No cap supplied. T Tilt CAP COLORS h c u AT3021 Flat Cap The cap is flush with the barrier To for Actuator Type B with Barrier Flange in normal position and .079” (2.0mm) below that in latchdown (22.0) (18.0) s Cap Material: .866 .709 position. or Polyphenylene Oxide cat (6.8) The latchdown feature on this Indi Finish: Matte .268 alternate action device provides visible, audible, and tactile feed- s e back. This design gives smooth, ori s responsive operation. es Cap Colors Available: c c A A B C H nt e Black Ivory Red Gray m e pl p u S www.nkkswitches.com C61

Series JP Internationally Approved Pushbuttons s e gl PANEL CUTOUT & TERMINALS g o T JPM & JPL Solder Lug/ s er .187”(4.75mm) Quick Connect Terminals k oc Panel Thickness Range R applies to both This switch assembly, JPM & JPL models. (12.180.02) when used with connectors, Epoxy Seal (7.2) ons is not VDE approved. .(015.59) R (.416.25).283 utt C .039” ~ .157” (0.65) R (3.2) b .026 .126 h (1.0mm ~ 4.0mm) (4.75) us .187 P Thk = (0.5) B (21.2) .020 P .835 d e at n mi u Ill TYPICAL SWITCH DIMENSIONS e bl a m m a gr Flat Cap with Barrier Flange JPM & JPL Single & Double Pole o Pr s ck Part No. (0.8) Typ (20.8) o .031 .819 yl e K (9.4) 2a 1a .370 s otarie ( 2.826.06) (12.064.67) COM 2 1 (13.21.200) R (0.5) .020 (4.75) Typ Slides (.1780.09) (24.0) (.417 .(527).5) (26.0) .(015.59) (7.2) ((.214010..249)) .187 .945 .098 1.024 .283 .835 Latchdown Position s e ctil JPM26B-H Single pole model does not have terminals 2 & 2a. a T Plunger with Flat Flange JPM & JPL Single & Double Pole Tilt Part No. (0.8) Typ (20.8) .031 .819 h uc (2.0) To .079 (1.0) (3.3) Sq .039 (9.4) 2a 1a .130 .370 (22.2) (31.0) ors .874 (2.5) Sq (12.064.67) COM 2 1 1.220 at .098 (1.0) (0.5) dic .039 .020 n (2.5) I .098 (8.5) .335 (4.75) Typ es (18.3) (6.5) (2.0) (1.5) (10.4) .187 ssori .720 (2.944.05) .25(.61663.00) .079 (12.062.04) .059 .(278.23) (..284130.259) e cc Latchdown Position A nt e m JPL16P Single pole model does not have terminals 2 & 2a. e pl p u S C62 www.nkkswitches.com

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: N KK Switches: JPM26P JPL16B-C JPL16B-H JPL16B-B JPM26B-H JPM26B-A JPM26B-C JPL26B-A JPL26B-B JPL26B-H JPM16B-C JPM16B-A JPM16B-H JPM16P JPL26P JPL16P JPL16B JPL26B/U JPL26B/U-B JPM16B JPM26B JPM16B-B JPM26B-B JPL16B-A JPL26B-C JPL26B