Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product Information in this Catalog (4) Power generation control equipment (nuclear power, Product information in this catalog is as of October 2019. All of the hydroelectric power, thermal power plant control system, etc.) contents specified herein and production status of the products listed (5) Undersea equipment (submarine repeating equipment, in this catalog are subject to change without notice due to technical underwater work equipment, etc.) improvement of our products, etc. Therefore, please check for the (6) Military equipment latest information carefully before practical application or use of our (7) Any other equipment requiring extremely high levels of safety products. and/or reliability equal to the equipment listed above Please note that TAIYO YUDEN shall not be in any way responsible *Notes: for any damages and defects in products or equipment incorporating 1. There is a possibility that our products can be used only our products, which are caused under the conditions other than those for aviation equipment that does not directly affect the safe specified in this catalog or individual product specification sheets. operation of aircraft (e.g., in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets ■ Approval of Product Specifications requirements specified separately by TAIYO YUDEN. Please Please contact TAIYO YUDEN for further details of product be sure to contact TAIYO YUDEN for further information specifications as the individual product specification sheets are before using our products for such aviation equipment. available. When using our products, please be sure to approve our 2. Implantable medical devices contain not only internal unit product specifications or make a written agreement on the product which is implanted in a body, but also external unit which is specification with TAIYO YUDEN in advance. connected to the internal unit. ■ Pre-Evaluation in the Actual Equipment and Conditions 4. Limitation of Liability Please conduct validation and verification of our products in actual Please note that unless you obtain prior written consent of TAIYO conditions of mounting and operating environment before using our YUDEN, TAIYO YUDEN shall not be in any way responsible for products. any damages incurred by you or third parties arising from use of the products listed in this catalog for any equipment that is not ■ Limited Application intended for use by TAIYO YUDEN, or any equipment requiring 1. Equipment Intended for Use inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN The products listed in this catalog are intended for general- as described above. purpose and standard use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office ■ Safety Design equipment, information and communication equipment including, When using our products for high safety and/or reliability-required without limitation, mobile phone, and PC) and other equipment equipment or circuits, please fully perform safety and/or reliability specified in this catalog or the individual product specification sheets. evaluation. In addition, please install (i) systems equipped with a protection circuit and a protection device and/or (ii) systems TAIYO YUDEN has the line-up of the products intended for equipped with a redundant circuit or other system to prevent an use in automotive electronic equipment, telecommunications unsafe status in the event of a single fault for a failsafe design to infrastructure and industrial equipment, or medical devices ensure safety. classified as GHTF Classes A to C (Japan Classes I to III). Therefore, when using our products for these equipment, ■ Intellectual Property Rights please check available applications specified in this catalog Information contained in this catalog is intended to convey examples or the individual product specification sheets and use the of typical performances and/or applications of our products and is corresponding products. not intended to make any warranty with respect to the intellectual property rights or any other related rights of TAIYO YUDEN or any 2. Equipment Requiring Inquiry third parties nor grant any license under such rights. Please be sure to contact TAIYO YUDEN for further information before using the products listed in this catalog for the following ■ Limited Warranty equipment (excluding intended equipment as specified in this Please note that the scope of warranty for our products is limited to catalog or the individual product specification sheets) which may the delivered our products themselves and TAIYO YUDEN shall not cause loss of human life, bodily injury, serious property damage be in any way responsible for any damages resulting from a failure and/or serious public impact due to a failure or defect of the or defect in our products. Notwithstanding the foregoing, if there is products and/or malfunction attributed thereto. a written agreement (e.g., supply and purchase agreement, quality (1) Transportation equipment (automotive powertrain control assurance agreement) signed by TAIYO YUDEN and your company, system, train control system, and ship control system, etc.) TAIYO YUDEN will warrant our products in accordance with such (2) Traffic signal equipment agreement. (3) Disaster prevention equipment, crime prevention equipment (4) Medical devices classified as GHTF Class C (Japan Class III) ■ TAIYO YUDEN’s Official Sales Channel (5) Highly public information network equipment, data- The contents of this catalog are applicable to our products which are processing equipment (telephone exchange, and base purchased from our sales offices or authorized distributors (hereinafter station, etc.) “TAIYO YUDEN’s official sales channel”). Please note that the contents (6) Any other equipment requiring high levels of quality and/or of this catalog are not applicable to our products purchased from any reliability equal to the equipment listed above seller other than TAIYO YUDEN’s official sales channel. 3. Equipment Prohibited for Use ■ Caution for Export Please do not incorporate our products into the following Some of our products listed in this catalog may require specific equipment requiring extremely high levels of safety and/or procedures for export according to“ U.S. Export Administration reliability. Regulations”,“ Foreign Exchange and Foreign Trade Control Law” (1) Aerospace equipment (artificial satellite, rocket, etc.) of Japan, and other applicable regulations. Should you have any (2) Aviation equipment *1 questions on this matter, please contact our sales staff. (3) Medical devices classified as GHTF Class D (Japan Class IV), implantable medical devices *2 20

for General Electronic Equipment for General Electronic Equipment MULTILAYER CERAMIC CAPACITORS MULTILAYER CERAMIC CAPACITORS C WAVE REFLOW AC PAER WAVE REFLOW CA ■PARTS NUMBER ITM OIC RS J M K 3 1 6 △ B J 1 0 6 M L － T △ △＝Blank space ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ M ①Rated voltage ③End termination U Code Rated voltage［VDC］ Code End termination L T P 2.5 K Plated ILA A 4 S Cu Internal Electrodes (For High Frequency) Y J 6.3 E R L 10 ④Dimension（L×W） C E 16 Type Dimensions EIA（inch） E T 25 （L×W）［mm］ R A G 35 021 0.25× 0.125 008004 M U 50 042 0.4 × 0.2 01005 IC H 100 063 0.6 × 0.3 0201 Q 250 1.0 × 0.5 0402 C 105 A S 630 0.52× 1.0 ※ 0204 P X 2000 1.6 × 0.8 0603 A 107 C 0.8 × 1.6 ※ 0306 IT ②Series name 212 2.0 × 1.25 0805 O Code Series name 1.25× 2.0 ※ 0508 R M Multilayer ceramic capacitor 316 3.2 × 1.6 1206 S V Multilayer ceramic capacitor for high frequency 325 3.2 × 2.5 1210 W LW reverse type multilayer capacitor 432 4.5 × 3.2 1812 Note : ※LW reverse type（□WK） only ⑤Dimension tolerance Code Type L［mm］ W［mm］ T［mm］ △ ALL Standard Standard Standard 063 0.6±0.05 0.3±0.05 0.3±0.05 105 1.0±0.10 0.5±0.10 0.5±0.10 107 1.6＋0.15/－0.05 0.8＋0.15/－0.05 0.8＋0.15/－0.05 0.45±0.05 A 212 2.0＋0.15/－0.05 1.25＋0.15/－0.05 0.85±0.10 1.25＋0.15/－0.05 0.85±0.10 316 3.2±0.20 1.6±0.20 1.6±0.20 325 3.2±0.30 2.5±0.30 2.5±0.30 063 0.6±0.09 0.3±0.09 0.3±0.09 105 1.0＋0.15/－0.05 0.5＋0.15/－0.05 0.5＋0.15/－0.05 0.45±0.05 107 1.6＋0.20/－0 0.8＋0.20/－0 0.8＋0.20/－0 B 0.45±0.05 212 2.0＋0.20/－0 1.25＋0.20/－0 0.85±0.10 1.25＋0.20/－0 316 3.2±0.30 1.6±0.30 1.6±0.30 C 105 1.0＋0.20/－0 0.5＋0.20/－0 0.5＋0.20/－0 063 0.6 + 0.25/- 0 0.3 + 0.25/- 0 0.3 + 0.25/ - 0 E 105 1.0＋0.30/－0 0.5＋0.30/－0 0.5＋0.30/－0 Note: cf. STANDARD EXTERNAL DIMENSIONS △= Blank space ⑥Temperature characteristics code ■High dielectric type（Excluding Super low distortion multilayer ceramic capacitor） Applicable Temperature Capacitance Tolerance Code Ref. Temp.［℃］ Capacitance change standard range［℃］ tolerance code ±10％ K JIS B －25～＋ 85 20 ±10％ ±20％ M BJ ±10％ K EIA X5R －55～＋ 85 25 ±15％ ±20％ M ±10％ K B7 EIA X7R －55～＋125 25 ±15％ ±20％ M ±10％ K C6 EIA X6S －55～＋105 25 ±22％ ±20％ M ±10％ K C7 EIA X7S －55～＋125 25 ±22％ ±20％ M ±10％ K LD(※) EIA X5R －55～＋ 85 25 ±15％ ±20％ M Note : ※.LD Low distortion high value multilayer ceramic capacitor △= Blank space c_mlcc_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 12 20

for General Electronic Equipment ■Temperature compensating type Applicable Temperature Capacitance Tolerance Code Ref. Temp.［℃］ Capacitance change standard range［℃］ tolerance code C ±0.05pF A AC ±0.1pF B PAER CA CG EIA C0G －55～＋125 25 0±30ppm/℃ ±0.25pF C ITM ±0.5pF D ORSIC ±5％ J ±0.25pF C JIS UJ 20 UJ －55～＋125 －750±120ppm/℃ ±0.5pF D M EIA U2J 25 ±5％ J U JIS UK －55～＋125 20 L UK －750±250ppm/℃ ±0.25pF C T EIA U2K －55～＋125 25 IL A Y ⑥Series code ⑨Thickness E R ・Super low distortion multilayer ceramic capacitor Code Thickness［mm］ C Code Series code K 0.125 E SD Standard H 0.13 R A E 0.18 M ・Medium-High Voltage Multilayer Ceramic Capacitor C 0.2 IC Code Series code D C SD Standard P A T 0.3 PA ⑦Nominal capacitance K 0.45（107type or more） C Code V IT Nominal capacitance 0.5 O （example） W R 0R5 0.5pF A 0.8 S 010 1pF D 0.85（212type or more） 100 10pF F 1.15 101 100pF G 1.25 102 1,000pF L 1.6 103 10,000pF N 1.9 104 0.1μF Y 2.0 max 105 1.0μF M 2.5 106 10μF 107 100μF ⑩Special code Note : R＝Decimal point Code Special code － Standard ⑧Capacitance tolerance Code Capacitance tolerance ⑪Packaging A ±0.05pF Code Packaging B ±0.1pF F φ178mm Taping （2mm pitch） C ±0.25pF T φ178mm Taping （4mm pitch） D ±0.5pF φ178mm Taping （4mm pitch, 1000 pcs/reel） P F ±1pF 325 type（Thickness code M） G ±2％ φ178mm Taping （2mm pitch）105type only R J ±5％ （Thickness code E,H） K ±10％ W φ178mm Taping（1mm pitch）021/042type only M ±20％ Z ＋80/－20％ ⑫Internal code Code Internal code △ Standard ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . c_mlcc_e-E08R01 20 13

for General Electronic Equipment ■STANDARD EXTERNAL DIMENSIONS W Dimension [mm] Type( EIA ) L L W T *1 e C □MK021（008004） 0.25±0.013 0.125±0.013 0.125±0.013 K 0.0675±0.0275 AC PAER T □VS021（008004） 0.25±0.013 0.125±0.013 0.125±0.013 K 0.0675±0.0275 CA C ITM □MK042（01005） 0.4±0.02 0.2±0.02 0.2±0.02 0.1±0.03 OIC e D RS □VS042（01005） 0.4±0.02 0.2±0.02 0.2±0.02 C 0.1±0.03 P □MK063（0201） 0.6±0.03 0.3±0.03 0.3±0.03 0.15±0.05 T M 0.13±0.02 H L U 0.18±0.02 E LT □MK105（0402） 1.0±0.05 0.5±0.05 0.2±0.02 C 0.25±0.10 IL W 0.3±0.03 P A 0.5±0.05 V Y E □VK105（0402） 1.0±0.05 0.5±0.05 0.5±0.05 W 0.25±0.10 R □WK105（0204）※ 0.52±0.05 1.0±0.05 0.3±0.05 P 0.18±0.08 CE T □MK107（0603） 1.6±0.10 0.8±0.10 0.45±0.05 K 0.35±0.25 R 0.8±0.10 A A e □WK107（0306）※ 0.8±0.10 1.6±0.10 0.5±0.05 V 0.25±0.15 M 0.45±0.05 K IC □MK212（0805） 2.0±0.10 1.25±0.10 0.85±0.10 D 0.5±0.25 C ※ LW reverse type 1.25±0.10 G A □WK212（0508）※ 1.25±0.15 2.0±0.15 0.85±0.10 D 0.3±0.2 P A 0.85±0.10 D C □MK316（1206） 3.2±0.15 1.6±0.15 1.15±0.10 F 0.5＋0.35/－0.25 IT 1.6±0.20 L O 0.85±0.10 D R S 1.15±0.10 F □MK325（1210） 3.2±0.30 2.5±0.20 1.9±0.20 N 0.6±0.3 1.9＋0.1/－0.2 Y 2.5±0.20 M 2.0+0/-0.30 Y 0.6±0.4 □MK432（1812） 4.5±0.40 3.2±0.30 2.5±0.20 M 0.9±0.6 Note : ※. LW reverse type, *1.Thickness code ■STANDARD QUANTITY Dimension Standard quantity［pcs］ Type EIA（inch） ［mm］ Code Paper tape Embossed tape 021 008004 0.125 K － 50000 C 042 01005 0.2 － 40000 D P 063 0201 0.3 15000 － T 0.13 H － 20000 0.18 E － 15000 0.2 C 20000 － 0402 105 0.3 P 15000 － V 0.5 W 10000 － 0204 ※ 0.30 P 0.45 K 0603 4000 － 107 0.8 A 0306 ※ 0.50 V － 4000 0.45 K 4000 － 0805 0.85 D 212 1.25 G － 3000 0508 ※ 0.85 D 4000 － 0.85 D 4000 － 316 1206 1.15 F － 3000 1.6 L － 2000 0.85 D 1.15 F － 2000 325 1210 1.9 N 2.0 max Y 2.5 M － 1000 2.0 max Y － 1000 432 1812 2.5 M － 500 Note : ※.LW Reverse type（□WK） c_mlcc_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 14 20

for General Electronic Equipment ■PARTS NUMBER ・ All the Multilayer Ceramic Capacitors of the catalog lineup are RoHS Compliant. ・ Capacitance tolerance code is applied to [] of part number. C Note) AC **12 WThee m eaxyc hparnogveid eo fX in7dRi/vXid7uSal fsopre scoifmicea titioenm iss anceccoersdsinagry t od etpheen idnidnigv iodnu atlh sep aepcpifliiccaattiioonn. and circuit condition. Please contact TAIYO YUDEN sales channels. PACERA *3 The size standard should look at ④Dimension, ⑤Dimension tolerance, and ⑨Thickness, and STANDARD EXTERNAL DIMENSIONS. ITM OIC RS Multilayer Ceramic Capacitors (High dielectric type) ●021TYPE M 【Temperature Characteristic BJ : X5R（－55～＋85℃）】　0.125mm thickness（K） U Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg LTIL EMK021 BJ221[]K-W X5R 220p ±10, ±20 10 150 0.125±0.013 R A EMK021 BJ471[]K-W 16 X5R 470p ±10, ±20 10 150 0.125±0.013 R Y EMK021 BJ102[]K-W X5R 1000p ±10, ±20 10 150 0.125±0.013 R E JMK021 BJ222[]K-W X5R 2200p ±10, ±20 10 150 0.125±0.013 R R JMK021 BJ472[]K-W 6.3 X5R 4700p ±10, ±20 10 150 0.125±0.013 R C JMK021 BJ103[]K-W X5R 0.01μ ±10, ±20 10 150 0.125±0.013 R E AMK021 BJ223MK-W 4 X5R 0.022μ ±20 10 150 0.125±0.013 R R A M ●042TYPE IC 【Temperature Characteristic BJ : B（－25～＋85℃）/X5R（－55～＋85℃）】　0.2mm thickness（C） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg CAP EMK042 BJ101[]C-W X5R 100p ±10, ±20 5 200 0.2±0.02 R A EMK042 BJ151[]C-W X5R 150p ±10, ±20 5 200 0.2±0.02 R C EMK042 BJ221[]C-W X5R 220p ±10, ±20 5 200 0.2±0.02 R IT EMK042 BJ331[]C-W X5R 330p ±10, ±20 5 200 0.2±0.02 R O EMK042 BJ471[]C-W X5R 470p ±10, ±20 5 200 0.2±0.02 R R EMK042 BJ681[]C-W X5R 680p ±10, ±20 5 200 0.2±0.02 R S EMK042 BJ102[]C-W 16 B X5R 1000p ±10, ±20 5 200 0.2±0.02 R EMK042 BJ152[]C-W X5R 1500p ±10, ±20 10 150 0.2±0.02 R EMK042 BJ222[]C-W X5R 2200p ±10, ±20 10 150 0.2±0.02 R EMK042 BJ332[]C-W X5R 3300p ±10, ±20 10 150 0.2±0.02 R EMK042 BJ472[]C-W X5R 4700p ±10, ±20 10 150 0.2±0.02 R EMK042 BJ682[]C-W X5R 6800p ±10, ±20 10 150 0.2±0.02 R EMK042 BJ103[]C-W X5R 0.01μ ±10, ±20 10 150 0.2±0.02 R LMK042 BJ101[]C-W X5R*1 100p ±10, ±20 5 200 0.2±0.02 R LMK042 BJ151[]C-W X5R*1 150p ±10, ±20 5 200 0.2±0.02 R LMK042 BJ221[]C-W X5R*1 220p ±10, ±20 5 200 0.2±0.02 R LMK042 BJ331[]C-W X5R*1 330p ±10, ±20 5 200 0.2±0.02 R LMK042 BJ471[]C-W X5R*1 470p ±10, ±20 5 200 0.2±0.02 R LMK042 BJ681[]C-W X5R*1 680p ±10, ±20 5 200 0.2±0.02 R LMK042 BJ102[]C-W 10 B X5R*1 1000p ±10, ±20 5 200 0.2±0.02 R LMK042 BJ152[]C-W X5R 1500p ±10, ±20 10 150 0.2±0.02 R LMK042 BJ222[]C-W X5R 2200p ±10, ±20 10 150 0.2±0.02 R LMK042 BJ332[]C-W X5R 3300p ±10, ±20 10 150 0.2±0.02 R LMK042 BJ472[]C-W X5R 4700p ±10, ±20 10 150 0.2±0.02 R LMK042 BJ682[]C-W X5R 6800p ±10, ±20 10 150 0.2±0.02 R LMK042 BJ103[]C-W X5R 0.01μ ±10, ±20 10 150 0.2±0.02 R JMK042 BJ152[]C-W X5R*1 1500p ±10, ±20 10 150 0.2±0.02 R JMK042 BJ222[]C-W X5R*1 2200p ±10, ±20 10 150 0.2±0.02 R JMK042 BJ332[]C-W X5R*1 3300p ±10, ±20 10 150 0.2±0.02 R JMK042 BJ472[]C-W X5R*1 4700p ±10, ±20 10 150 0.2±0.02 R JMK042 BJ682[]C-W 6.3 X5R*1 6800p ±10, ±20 10 150 0.2±0.02 R JMK042 BJ103[]C-W X5R*1 0.01μ ±10, ±20 10 150 0.2±0.02 R JMK042 BJ223[]C-W X5R 0.022μ ±10, ±20 10 150 0.2±0.02 R JMK042 BJ473[]C-W X5R 0.047μ ±10, ±20 10 150 0.2±0.02 R JMK042 BJ104[]C-W X5R 0.1μ ±10, ±20 10 150 0.2±0.02 R AMK042 BJ473[]C-W X5R 0.047μ ±10, ±20 10 150 0.2±0.02 R 4 AMK042 BJ104[]C-W X5R 0.1μ ±10, ±20 10 150 0.2±0.02 R 【Temperature Characteristic B7 : X7R（－55～＋125℃）】　0.2mm thickness（C） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg EMK042 B7101[]C-W X7R 100p ±10, ±20 5 200 0.2±0.02 R EMK042 B7151[]C-W X7R 150p ±10, ±20 5 200 0.2±0.02 R EMK042 B7221[]C-W X7R 220p ±10, ±20 5 200 0.2±0.02 R EMK042 B7331[]C-W 16 X7R 330p ±10, ±20 5 200 0.2±0.02 R EMK042 B7471[]C-W X7R 470p ±10, ±20 5 200 0.2±0.02 R EMK042 B7681[]C-W X7R 680p ±10, ±20 5 200 0.2±0.02 R EMK042 B7102[]C-W X7R 1000p ±10, ±20 5 200 0.2±0.02 R LMK042 B7101[]C-W X7R 100p ±10, ±20 5 200 0.2±0.02 R LMK042 B7151[]C-W X7R 150p ±10, ±20 5 200 0.2±0.02 R LMK042 B7221[]C-W X7R 220p ±10, ±20 5 200 0.2±0.02 R LMK042 B7331[]C-W 10 X7R 330p ±10, ±20 5 200 0.2±0.02 R LMK042 B7471[]C-W X7R 470p ±10, ±20 5 200 0.2±0.02 R LMK042 B7681[]C-W X7R 680p ±10, ±20 5 200 0.2±0.02 R LMK042 B7102[]C-W X7R 1000p ±10, ±20 5 200 0.2±0.02 R c_mlcc_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 20 15

for General Electronic Equipment ■PARTS NUMBER ●063TYPE 【Temperature Characteristic BJ : B（－25～＋85℃）/X5R（－55～＋85℃）】　0.3mm thickness（P） CAPACER UMK06P3a rBtJ n1u0m1[b]ePr- 1F Part number 2 Rated[ Vv]oltage cThBaermapceterarXitsu5triRce*s1 Capa c[1Fi0t]a0npce Capac±ita1n[0c％,e ± ]to2l0erance t a[3％n.5δ] Rated vH2oT0ltL0aTge x ％Thic0k.n3e±ss0*.30 3[mm] SRWo:R:lWdeReafrlvoinewg CITORSAMIC UUUUMMMMKKKK000066663333 BBBBJJJJ123452371111[[[[]]]]PPPP----FFFF BBBB XXXX5555RRRR****1111 123452370000pppp ±±±±11110000,,,, ±±±±22220000 3333....5555 222200000000 0000....3333±±±±0000....00003333 RRRR UMK063 BJ681[]P-F B X5R*1 680p ±10, ±20 3.5 200 0.3±0.03 R UMK063 BJ102[]P-F 50 B X5R*1 1000p ±10, ±20 3.5 200 0.3±0.03 R M UMK063 BJ152[]P-F B X5R 1500p ±10, ±20 5 200 0.3±0.03 R UMK063 BJ222[]P-F B X5R 2200p ±10, ±20 5 200 0.3±0.03 R U UMK063 BJ332[]P-F B X5R 3300p ±10, ±20 5 200 0.3±0.03 R LT UMK063 BJ472[]P-F B X5R 4700p ±10, ±20 5 200 0.3±0.03 R IL UMK063 BJ682[]P-F B X5R 6800p ±10, ±20 5 200 0.3±0.03 R A UMK063 BJ103[]P-F B X5R 0.01μ ±10, ±20 5 200 0.3±0.03 R Y GMK063 BJ104[]P-F 35 X5R 0.1μ ±10, ±20 10 150 0.3±0.03 R E TMK063 BJ152[]P-F B X5R 1500p ±10, ±20 5 200 0.3±0.03 R R TMK063 BJ222[]P-F B X5R 2200p ±10, ±20 5 200 0.3±0.03 R C TMK063 BJ332[]P-F B X5R 3300p ±10, ±20 5 200 0.3±0.03 R E TMK063 BJ472[]P-F 25 B X5R 4700p ±10, ±20 5 200 0.3±0.03 R R TMK063 BJ682[]P-F B X5R 6800p ±10, ±20 5 200 0.3±0.03 R A TMK063 BJ103[]P-F B X5R 0.01μ ±10, ±20 5 200 0.3±0.03 R M TMK063 BJ223[]P-F B X5R 0.022μ ±10, ±20 7.5 200 0.3±0.03 R IC TEMMKK006633 ABBJJ115024[][P]P--FF B XX55RR*1 1500.01pμ ±±1100,, ±±2200 150 210500 00..33±±00..0035 RR C EMK063 BJ222[]P-F B X5R*1 2200p ±10, ±20 5 200 0.3±0.03 R A EMK063 BJ332[]P-F B X5R*1 3300p ±10, ±20 5 200 0.3±0.03 R P EMK063 BJ472[]P-F B X5R*1 4700p ±10, ±20 5 200 0.3±0.03 R A EMK063 BJ682[]P-F B X5R*1 6800p ±10, ±20 5 200 0.3±0.03 R C EMK063 BJ103[]P-F B X5R*1 0.01μ ±10, ±20 5 200 0.3±0.03 R IT EMK063 BJ153[]P-F 16 X5R 0.015μ ±10, ±20 7.5 200 0.3±0.03 R O EMK063 BJ223[]P-F B X5R 0.022μ ±10, ±20 7.5 200 0.3±0.03 R R EMK063 BJ333[]P-F X5R 0.033μ ±10, ±20 7.5 150 0.3±0.03 R S EMK063 BJ473[]P-F X5R 0.047μ ±10, ±20 7.5 150 0.3±0.03 R EMK063 BJ683[]P-F X5R 0.068μ ±10, ±20 10 150 0.3±0.03 R EMK063 BJ104[]P-F X5R 0.1μ ±10, ±20 10 150 0.3±0.03 R EMK063 BJ224[]P-F X5R 0.22μ ±10, ±20 10 150 0.3±0.03 R EMK063BBJ474[]PLF X5R 0.47μ ±10, ±20 10 150 0.3±0.09 R LMK063 BJ223[]P-F B X5R 0.022μ ±10, ±20 7.5 150 0.3±0.03 R LMK063 BJ333[]P-F X5R 0.033μ ±10, ±20 7.5 150 0.3±0.03 R LMK063 BJ473[]P-F X5R 0.047μ ±10, ±20 7.5 150 0.3±0.03 R LMK063 BJ683[]P-F X5R 0.068μ ±10, ±20 10 150 0.3±0.03 R 10 LMK063 BJ104[]P-F X5R 0.1μ ±10, ±20 10 150 0.3±0.03 R LMK063 BJ224[]P-F X5R 0.22μ ±10, ±20 10 150 0.3±0.03 R LMK063BBJ474[]PLF X5R 0.47μ ±10, ±20 10 150 0.3±0.09 R LMK063BBJ105MPLF X5R 1μ ±20 10 150 0.3±0.09 R JMK063 BJ104[]P-F X5R 0.1μ ±10, ±20 10 150 0.3±0.03 R JMK063 BJ224[]P-F X5R 0.22μ ±10, ±20 10 150 0.3±0.03 R JMK063 BJ334MP-F 6.3 X5R 0.33μ ±20 10 150 0.3±0.03 R JMK063 BJ474[]P-F X5R 0.47μ ±10, ±20 10 150 0.3±0.03 R JMK063ABJ105[]P-F X5R 1μ ±10, ±20 10 150 0.3±0.05 R PMK063EBJ475MP-F 2.5 X5R 4.7μ ±20 10 150 0.3+0.25/-0 R 【Temperature Characteristic C6 : X6S（－55～＋105℃）】　0.3mm thickness（P） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg TMK063 C6104[]P-F 25 X6S 0.1μ ±10, ±20 10 150 0.3±0.03 R EMK063AC6104[]P-F 16 X6S 0.1μ ±10, ±20 10 150 0.3±0.05 R LMK063 C6104[]P-F X6S 0.1μ ±10, ±20 10 150 0.3±0.03 R LMK063 C6224[]P-F 10 X6S 0.22μ ±10, ±20 10 150 0.3±0.03 R LMK063BC6474[]PLF X6S 0.47μ ±10, ±20 10 150 0.3±0.09 R JMK063 C6104[]P-F X6S 0.1μ ±10, ±20 10 150 0.3±0.03 R JMK063 C6224[]P-F X6S 0.22μ ±10, ±20 10 150 0.3±0.03 R 6.3 JMK063BC6474[]P-F X6S 0.47μ ±10, ±20 10 150 0.3±0.09 R JMK063BC6105MP-F X6S 1μ ±20 10 150 0.3±0.09 R AMK063 C6474[]P-F X6S 0.47μ ±10, ±20 10 150 0.3±0.03 R 4 AMK063AC6105[]P-F X6S 1μ ±10, ±20 10 150 0.3±0.05 R c_mlcc_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 16 20

for General Electronic Equipment ■PARTS NUMBER 【Temperature Characteristic B7 : X7R（－55～＋125℃）】　0.3mm thickness（P） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg C UUMMKK006633 BB77110511[[]]PP--FF XX77RR 110500pp ±±1100,, ±±2200 33..55 220000 00..33±±00..0033 RR APACER UUUUMMMMKKKK000066663333 BBBB7777234623781111[[[[]]]]PPPP----FFFF 50 XXXX7777RRRR 234623780000pppp ±±±±11110000,,,, ±±±±22220000 3333....5555 222200000000 0000....3333±±±±0000....00003333 RRRR CITORSAMIC UMK063 B7102[]P-F X7R 1000p ±10, ±20 3.5 200 0.3±0.03 R TMK063 B7152[]P-F X7R 1500p ±10, ±20 5 200 0.3±0.03 R TMK063 B7222[]P-F X7R 2200p ±10, ±20 5 200 0.3±0.03 R M TMK063 B7332[]P-F X7R 3300p ±10, ±20 5 200 0.3±0.03 R TMK063 B7472[]P-F 25 X7R 4700p ±10, ±20 5 200 0.3±0.03 R U TMK063 B7682[]P-F X7R 6800p ±10, ±20 5 200 0.3±0.03 R LT TMK063 B7103[]P-F X7R 0.01μ ±10, ±20 5 200 0.3±0.03 R IL EMK063 B7152[]P-F X7R 1500p ±10, ±20 5 200 0.3±0.03 R A EMK063 B7222[]P-F X7R 2200p ±10, ±20 5 200 0.3±0.03 R Y EMK063 B7332[]P-F X7R 3300p ±10, ±20 5 200 0.3±0.03 R E EMK063 B7472[]P-F 16 X7R 4700p ±10, ±20 5 200 0.3±0.03 R R EMK063 B7682[]P-F X7R 6800p ±10, ±20 5 200 0.3±0.03 R C EMK063 B7103[]P-F X7R 0.01μ ±10, ±20 5 200 0.3±0.03 R E EMK063 B7223[]P-F X7R 0.022μ ±10, ±20 7.5 150 0.3±0.03 R R A M ●105TYPE IC 【Temperature Characteristic BJ : B（－25～＋85℃）/X5R（－55～＋85℃）】　0.5mm thickness（V） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg CAP UMK105 BJ223[]V-F X5R 0.022μ ±10, ±20 5 200 0.5±0.05 R A UMK105 BJ473[]V-F X5R 0.047μ ±10, ±20 5 200 0.5±0.05 R C UMK105 BJ104[]V-F 50 X5R 0.1μ ±10, ±20 10 150 0.5±0.05 R IT UMK105 BJ224[]V-F X5R 0.22μ ±10, ±20 10 150 0.5±0.05 R O UMK105ABJ474[]V-F X5R 0.47μ ±10, ±20 10 150 0.5±0.10 R R UMK105CBJ105MV-F X5R 1μ ±20 10 150 0.5+0.20/-0 R S GMK105 BJ104[]V-F B X5R 0.1μ ±10, ±20 5 150 0.5±0.05 R 35 GMK105ABJ105[]V-F X5R 1μ ±10, ±20 10 150 0.5±0.10 R TMK105 BJ153[]V-F B X5R*1 0.015μ ±10, ±20 3.5 200 0.5±0.05 R TMK105 BJ223[]V-F B X5R*1 0.022μ ±10, ±20 3.5 200 0.5±0.05 R TMK105 BJ333[]V-F B X5R*1 0.033μ ±10, ±20 3.5 150 0.5±0.05 R TMK105 BJ473[]V-F B X5R*1 0.047μ ±10, ±20 3.5 150 0.5±0.05 R TMK105 BJ104[]V-F 25 B X5R 0.1μ ±10, ±20 5 150 0.5±0.05 R TMK105 BJ224[]V-F X5R 0.22μ ±10, ±20 10 200 0.5±0.05 R TMK105ABJ474[]V-F X5R 0.47μ ±10, ±20 10 200 0.5±0.10 R TMK105 BJ105[]V-F X5R 1μ ±10, ±20 10 150 0.5±0.05 R TMK105CBJ225[]V-F X5R 2.2μ ±10, ±20 10 150 0.5+0.20/-0 R EMK105 BJ224[]V-F B X5R 0.22μ ±10, ±20 5 150 0.5±0.05 R EMK105ABJ474[]V-F X5R 0.47μ ±10, ±20 10 200 0.5±0.10 R 16 EMK105 BJ105[]V-F X5R 1μ ±10, ±20 10 150 0.5±0.05 R EMK105ABJ225[]V-F X5R 2.2μ ±10, ±20 10 150 0.5±0.10 R LMK105 BJ225[]V-F X5R 2.2μ ±10, ±20 10 150 0.5±0.05 R 10 LMK105BBJ475MVLF X5R 4.7μ ±20 10 150 0.5+0.15/-0.05 R JMK105 BJ225[]V-F X5R 2.2μ ±10, ±20 10 150 0.5±0.05 R 6.3 JMK105BBJ475MV-F JMK105 BJ475MV-FD X5R 4.7μ ±20 10 150 0.5+0.15/-0.05 R AMK105EBJ226MV-F 4 X5R 22μ ±20 20 150 0.5+0.30/-0 R 【Temperature Characteristic BJ : B（－25～＋85℃）/X5R（－55～＋85℃）】　0.3mm thickness（P） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg UMK105 BJ104[]P-F 50 X5R 0.1μ ±10, ±20 10 150 0.3±0.03 R TMK105 BJ103[]P-F B X5R 0.01μ ±10, ±20 5 150 0.3±0.03 R TMK105 BJ104[]P-F X5R 0.1μ ±10, ±20 10 150 0.3±0.03 R 25 TMK105 BJ224[]P-F X5R 0.22μ ±10, ±20 10 150 0.3±0.03 R TMK105 BJ474[]P-F X5R 0.47μ ±10, ±20 10 150 0.3±0.03 R EMK105 BJ474[]P-F 16 X5R 0.47μ ±10, ±20 10 150 0.3±0.03 R LMK105 BJ105[]PLF 10 X5R 1μ ±10, ±20 10 150 0.3±0.03 R JMK105 BJ105[]P-F 6.3 X5R 1μ ±10, ±20 10 150 0.3±0.03 R AMK105 BJ225MP-F 4 X5R 2.2μ ±20 10 150 0.3±0.03 R 【Temperature Characteristic BJ : X5R（－55～＋85℃）】　0.2mm thickness（C） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg LMK105 BJ104[]C-F 10 X5R 0.1μ ±10, ±20 10 150 0.2±0.02 R JMK105 BJ224[]C-F X5R 0.22μ ±10, ±20 10 150 0.2±0.02 R JMK105 BJ474[]C-F 6.3 X5R 0.47μ ±10, ±20 10 150 0.2±0.02 R JMK105 BJ105MC-F X5R 1μ ±20 10 150 0.2±0.02 R 【Temperature Characteristic BJ : X5R（－55～＋85℃）】　0.18mm thickness（E） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg LMK105 BJ104[]E-R 10 X5R 0.1μ ±10, ±20 10 150 0.18±0.02 R JMK105 BJ224[]E-R X5R 0.22μ ±10, ±20 10 150 0.18±0.02 R 6.3 JMK105 BJ474[]E-R X5R 0.47μ ±10, ±20 10 150 0.18±0.02 R AMK105 BJ105ME-R 4 X5R 1μ ±20 10 150 0.18±0.02 R c_mlcc_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 20 17

for General Electronic Equipment ■PARTS NUMBER 【Temperature Characteristic BJ : X5R（－55～＋85℃）】　0.13mm thickness（H） C Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg APACER LJMMKK110055 BBJJ120244MMHH--RR 61.03 XX55RR 0.02.21μμ ±±2200 1100 115500 00..1133±±00..0022 RR CITAM AMK105 BJ474MH-R 4 X5R 0.47μ ±20 10 150 0.13±0.02 R OIC RS 【Temperature Characteristic C6 : X6S（－55～＋105℃）】　0.5mm thickness（V） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg M GMK105CC6105MV-F 35 X6S 1μ ±20 10 150 0.5+0.20/-0 R TMK105AC6105[]V-F 25 X6S 1μ ±10, ±20 10 150 0.5±0.10 R U EMK105 C6105[]V-F X6S 1μ ±10, ±20 10 150 0.5±0.05 R LT EMK105CC6225MV-F 16 X6S 2.2μ ±20 10 150 0.5+0.20/-0 R IL LMK105 C6105[]V-F 10 X6S 1μ ±10, ±20 10 200 0.5±0.05 R A LMK105AC6225MV-F X6S 2.2μ ±20 10 150 0.5±0.10 R Y JMK105 C6105[]V-F X6S 1μ ±10, ±20 10 150 0.5±0.05 R E JMK105 C6225MV-F 6.3 X6S 2.2μ ±20 10 150 0.5±0.05 R R JMK105BC6475MV-F X6S 4.7μ ±20 10 150 0.5+0.15/-0.05 R C AMK105BC6475MV-F 4 X6S 4.7μ ±20 10 200 0.5+0.15/-0.05 R E R 【Temperature Characteristic B7 : X7R（－55～＋125℃）】　0.5mm thickness（V） A MIC Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg UMK105 B7152[]V-F X7R 1500p ±10, ±20 2.5 200 0.5±0.05 R C UMK105 B7222[]V-F X7R 2200p ±10, ±20 2.5 200 0.5±0.05 R A UMK105 B7332[]V-F X7R 3300p ±10, ±20 2.5 200 0.5±0.05 R P UMK105 B7472[]V-F X7R 4700p ±10, ±20 2.5 150 0.5±0.05 R A UMK105 B7682[]V-F 50 X7R 6800p ±10, ±20 2.5 150 0.5±0.05 R C UMK105 B7103[]V-F X7R 0.01μ ±10, ±20 3.5 150 0.5±0.05 R IT UMK105 B7223[]V-FR X7R 0.022μ ±10, ±20 10 200 0.5±0.05 R O UMK105 B7473[]V-FR X7R 0.047μ ±10, ±20 10 200 0.5±0.05 R R UMK105 B7104[]V-FR X7R 0.1μ ±10, ±20 10 150 0.5±0.05 R S TMK105 B7223[]V-F X7R 0.022μ ±10, ±20 3.5 150 0.5±0.05 R TMK105 B7473[]V-F X7R 0.047μ ±10, ±20 3.5 150 0.5±0.05 R 25 TMK105 B7104[]V-FR X7R 0.1μ ±10, ±20 10 200 0.5±0.05 R TMK105 B7224[]V-FR X7R 0.22μ ±10, ±20 10 150 0.5±0.05 R EMK105 B7223[]V-F X7R 0.022μ ±10, ±20 3.5 200 0.5±0.05 R EMK105 B7473[]V-F X7R 0.047μ ±10, ±20 3.5 200 0.5±0.05 R 16 EMK105 B7104[]V-F X7R 0.1μ ±10, ±20 5 150 0.5±0.05 R EMK105 B7224[]V-FR X7R 0.22μ ±10, ±20 10 150 0.5±0.05 R LMK105 B7224[]V-FR X7R 0.22μ ±10, ±20 10 150 0.5±0.05 R 10 LMK105 B7474[]V-F X7R 0.47μ ±10, ±20 10 150 0.5±0.05 R JMK105 B7224[]V-F X7R 0.22μ ±10, ±20 5 150 0.5±0.05 R 6.3 JMK105 B7474[]V-F X7R 0.47μ ±10, ±20 10 150 0.5±0.05 R ●107TYPE 【Temperature Characteristic BJ : B（－25～＋85℃）/X5R（－55～＋85℃）】　0.8mm thickness（A） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg UMK107ABJ474[]A-T UMK107 BJ474[]A-TD X5R 0.47μ ±10, ±20 10 150 0.8+0.15/-0.05 R UMK107 BJ105[]A-T 50 X5R 1μ ±10, ±20 10 150 0.8±0.10 R UMK107BBJ225[]A-T X5R 2.2μ ±10, ±20 10 150 0.8+0.20/-0 R GMK107BBJ475[]A-T 35 X5R 4.7μ ±10, ±20 10 150 0.8+0.20/-0 R TMK107ABJ225[]A-T TMK107 BJ225[]A-TD X5R 2.2μ ±10, ±20 10 150 0.8+0.15/-0.05 R TMK107BBJ475[]A-T 25 X5R 4.7μ ±10, ±20 10 150 0.8+0.20/-0 R TMK107BBJ106MA-T X5R 10μ ±20 10 150 0.8+0.20/-0 R EMK107ABJ475[]A-T EMK107 BJ475[]A-TD X5R 4.7μ ±10, ±20 10 150 0.8+0.15/-0.05 R 16 EMK107BBJ106MA-T X5R 10μ ±20 10 150 0.8+0.20/-0 R LMK107BBJ106[]ALT LMK107 BJ106[]ALTD X5R 10μ ±10, ±20 10 150 0.8+0.20/-0 R 10 LMK107BBJ226MA-T X5R 22μ ±20 10 150 0.8+0.20/-0 R JMK107ABJ106[]A-T JMK107 BJ106[]A-T X5R 10μ ±10, ±20 10 150 0.8+0.15/-0.05 R JMK107BBJ226MA-T 6.3 X5R 22μ ±20 10 150 0.8+0.20/-0 R JMK107BBJ476MA-RE X5R 47μ ±20 15 150 0.8+0.20/-0 R AMK107BBJ476MA-RE 4 X5R 47μ ±20 20 150 0.8+0.20/-0 R 【Temperature Characteristic BJ : X5R（－55～＋85℃）】　0.45mm thickness（K） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg TMK107 BJ105[]K-T 25 X5R 1μ ±10, ±20 10 150 0.45±0.05 R EMK107 BJ105[]K-T X5R 1μ ±10, ±20 10 150 0.45±0.05 R 16 EMK107BBJ225[]K-T X5R 2.2μ ±10, ±20 10 150 0.45±0.05 R LMK107 BJ105[]K-T X5R 1μ ±10, ±20 10 150 0.45±0.05 R LMK107 BJ225[]K-T 10 X5R 2.2μ ±10, ±20 10 150 0.45±0.05 R LMK107BBJ475MKLT LMK107 BJ475MKLTD X5R 4.7μ ±20 10 150 0.45±0.05 R JMK107 BJ105[]K-T X5R 1μ ±10, ±20 10 150 0.45±0.05 R JMK107 BJ225[]K-T X5R 2.2μ ±10, ±20 10 150 0.45±0.05 R 6.3 JMK107 BJ475MK-T X5R 4.7μ ±20 10 150 0.45±0.05 R JMK107BBJ106MK-TT X5R 10μ ±20 10 150 0.45±0.05 R AMK107BBJ106MK-T*2 4 X5R 10μ ±20 10 150 0.45±0.05 R c_mlcc_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 18 20

for General Electronic Equipment ■PARTS NUMBER 【Temperature Characteristic C6 : X6S（－55～＋105℃）】　0.8mm thickness（A） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg C TEMMKK110077 BCC66120255[][A]A--TT 25 XX66SS 2.21μμ ±±1100,, ±±2200 150 115500 0.08.+80±.200./1-00 RR APACER EEMMKK110077BBCC66242755[[]]AA--TT 16 XX66SS 24..27μμ ±±1100,, ±±2200 1100 115500 00..88++00..2200//--00 RR CITOAMIC ELMMKK110077 BCC66110056[]MAA--TT XX66SS 101μμ ±1±0, 2±020 150 115500 0.08.+80±.200./1-00 RR RS LMK107AC6475[]A-T 10 X6S 4.7μ ±10, ±20 10 150 0.8+0.15/-0.05 R LMK107BC6106MA-T X6S 10μ ±20 10 150 0.8+0.20/-0 R JMK107 C6475[]A-T X6S 4.7μ ±10, ±20 10 150 0.8±0.10 R M JMK107BC6106MA-T 6.3 X6S 10μ ±20 10 150 0.8+0.20/-0 R JMK107BC6226MA-T X6S 22μ ±20 10 150 0.8+0.20/-0 R U AMK107BC6226MA-T 4 X6S 22μ ±20 10 150 0.8+0.20/-0 R LT IL 【Temperature Characteristic B7 : X7R（－55～＋125℃）】　0.8mm thickness（A） A Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg YER UMK107 B7224[]A-TR X7R 0.22μ ±10, ±20 10 150 0.8±0.10 R C UMK107 B7474[]A-TR 50 X7R 0.47μ ±10, ±20 10 150 0.8±0.10 R E UMK107AB7105[]A-T X7R 1μ ±10, ±20 10 150 0.8+0.15/-0.05 R R TMK107 B7474[]A-TR X7R 0.47μ ±10, ±20 10 150 0.8±0.10 R A TMK107 B7105[]A-T 25 X7R 1μ ±10, ±20 10 150 0.8±0.10 R M EMK107 B7474[]A-T X7R 0.47μ ±10, ±20 3.5 150 0.8±0.10 R IC EMK107 B7105[]A-T 16 X7R 1μ ±10, ±20 5 150 0.8±0.10 R EMK107BB7225[]A-T X7R 2.2μ ±10, ±20 10 150 0.8+0.20/-0 R C LMK107 B7225[]A-TR 10 X7R 2.2μ ±10, ±20 10 150 0.8±0.10 R A JMK107 B7225[]A-TR X7R 2.2μ ±10, ±20 10 200 0.8±0.10 R P JMK107BB7475[]A-T 6.3 X7R 4.7μ ±10, ±20 10 150 0.8+0.20/-0 R A C IT ●212TYPE O 【Temperature Characteristic BJ : B（－25～＋85℃）/X5R（－55～＋85℃）】　1.25mm thickness（G） R Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg S UMK212BBJ475[]G-T 50 X5R 4.7μ ±10, ±20 10 150 1.25+0.20/-0 R GMK212BBJ106[]G-T 35 X5R 10μ ±10, ±20 10 150 1.25+0.20/-0 R TMK212ABJ475[]G-T TMK212 BJ475[]G-T X5R 4.7μ ±10, ±20 10 150 1.25+0.15/-0.05 R TMK212BBJ106MG-T 25 X5R 10μ ±20 10 150 1.25+0.20/-0 R TMK212BBJ226MG-TT X5R 22μ ±20 10 150 1.25+0.20/-0 R EMK212ABJ106[]G-T EMK212 BJ106[]G-T X5R 10μ ±10, ±20 10 150 1.25+0.15/-0.05 R 16 EMK212BBJ226MG-T X5R 22μ ±20 10 150 1.25+0.20/-0 R LMK212BBJ476MG-T 10 X5R 47μ ±20 10 150 1.25+0.20/-0 R JMK212BBJ476MG-T JMK212 BJ476MG-T X5R 47μ ±20 10 150 1.25+0.20/-0 R 6.3 JMK212BBJ107MG-TE X5R 100μ ±20 20 150 1.25+0.20/-0 R AMK212BBJ107MG-TE 4 X5R 100μ ±20 20 150 1.25+0.20/-0 R PMK212BBJ107MG-T 2.5 X5R 100μ ±20 10 150 1.25+0.20/-0 R 【Temperature Characteristic BJ : B（－25～＋85℃）/X5R（－55～＋85℃）】　0.85mm thickness（D） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg UMK212ABJ105[]D-T UMK212 BJ105[]D-TD X5R 1μ ±10, ±20 10 150 0.85±0.10 R 50 UMK212BBJ225[]D-T X5R 2.2μ ±10, ±20 10 150 0.85±0.10 R GMK212BBJ475[]D-T 35 X5R 4.7μ ±10, ±20 10 150 0.85±0.10 R TMK212 BJ474[]D-T B X5R 0.47μ ±10, ±20 3.5 200 0.85±0.10 R TMK212 BJ105[]D-T B X5R 1μ ±10, ±20 5 200 0.85±0.10 R TMK212ABJ225[]D-T TMK212 BJ225[]D-T 25 X5R 2.2μ ±10, ±20 5 150 0.85±0.10 R TMK212BBJ475[]D-T TMK212 BJ475[]D-TD X5R 4.7μ ±10, ±20 10 150 0.85±0.10 R TMK212BBJ106[]D-T X5R 10μ ±10, ±20 10 150 0.85±0.10 R EMK212 BJ105[]D-T B X5R*1 1μ ±10, ±20 5 200 0.85±0.10 R EMK212ABJ225[]D-T EMK212 BJ225[]D-T 16 X5R*1 2.2μ ±10, ±20 5 200 0.85±0.10 R EMK212 BJ475[]D-T X5R 4.7μ ±10, ±20 10 150 0.85±0.10 R EMK212ABJ106[]D-T EMK212 BJ106[]D-TD X5R 10μ ±10, ±20 10 150 0.85±0.10 R LMK212 BJ105[]D-T B X5R*1 1μ ±10, ±20 3.5 200 0.85±0.10 R LMK212 BJ225[]D-T 10 X5R*1 2.2μ ±10, ±20 5 200 0.85±0.10 R LMK212ABJ106[]D-T LMK212 BJ106[]D-T X5R 10μ ±10, ±20 10 150 0.85±0.10 R LMK212BBJ226MD-T X5R 22μ ±20 10 150 0.85±0.10 R JMK212ABJ106[]D-T JMK212 BJ106[]D-T X5R 10μ ±10, ±20 10 200 0.85±0.10 R 6.3 JMK212ABJ226MD-T JMK212 BJ226MD-T X5R 22μ ±20 10 150 0.85±0.10 R AMK212BBJ476MD-T 4 X5R 47μ ±20 10 150 0.85±0.10 R 【Temperature Characteristic C6 : X6S（－55～＋105℃）】　1.25mm thickness（G） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg TMK212BC6106[]G-T 25 X6S 10μ ±10, ±20 10 150 1.25+0.20/-0 R EMK212BC6226MG-TT 16 X6S 22 μ ±20 10 150 1.25+0.20/-0 R LMK212BC6226MG-T 10 X6S 22μ ±20 10 150 1.25+0.20/-0 R JMK212BC6226MG-T X6S 22μ ±20 10 150 1.25+0.20/-0 R 6.3 JMK212BC6476MG-T X6S 47μ ±20 10 150 1.25+0.20/-0 R AMK212BC6476MG-T X6S 47μ ±20 10 150 1.25+0.20/-0 R 4 AMK212BC6107MG-TE X6S 100μ ±20 20 150 1.25+0.20/-0 R c_mlcc_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 20 19

for General Electronic Equipment ■PARTS NUMBER 【Temperature Characteristic C6 : X6S（－55～＋105℃）】　0.85mm thickness（D） C Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg APACER LAMMKK221122ABCC66120266[M]DD--TT 140 XX66SS 1202μμ ±1±0, 2±020 1100 115500 00..8855±±00..1100 RR CA ITM OIC 【Temperature Characteristic B7 : X7R（－55～＋125℃）】　1.25mm thickness（G） RS Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg UMK212 B7224[]G-T X7R 0.22μ ±10, ±20 3.5 150 1.25±0.10 R/W M UMK212 B7474[]G-T 50 X7R 0.47μ ±10, ±20 3.5 150 1.25±0.10 R/W UMK212 B7105[]G-T X7R 1μ ±10, ±20 10 150 1.25±0.10 R/W U UMK212BB7225[]G-T X7R 2.2μ ±10, ±20 10 150 1.25+0.20/-0 R LT GMK212 B7105[]G-T 35 X7R 1μ ±10, ±20 3.5 150 1.25±0.10 R/W IL TMK212 B7225[]G-TR 25 X7R 2.2μ ±10, ±20 10 150 1.25±0.10 R A TMK212AB7475[]G-T TMK212 B7475[]G-T X7R 4.7μ ±10, ±20 10 150 1.25+0.15/-0.05 R Y EMK212 B7475[]G-T 16 X7R 4.7μ ±10, ±20 10 150 1.25±0.10 R E EMK212BB7106MG-T X7R 10μ ±20 10 150 1.25+0.20/-0 R R LMK212AB7106[]G-T LMK212 B7106[]G-TD 10 X7R 10μ ±10, ±20 10 150 1.25+0.15/-0.05 R C JMK212AB7106[]G-T JMK212 B7106[]G-T 6.3 X7R 10μ ±10, ±20 10 150 1.25+0.15/-0.05 R E R 【Temperature Characteristic B7 : X7R（－55～＋125℃）】　0.85mm thickness（D） A MIC Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg UMK212AB7104[]D-T X7R 0.1μ ±10, ±20 10 150 0.85±0.10 R C UMK212AB7224[]D-T X7R 0.22μ ±10, ±20 10 150 0.85±0.10 R 50 A UMK212AB7474[]D-T X7R 0.47μ ±10, ±20 10 150 0.85±0.10 R P UMK212AB7105[]D-T X7R 1μ ±10, ±20 10 150 0.85±0.10 R A TMK212AB7225[]D-TR 25 X7R 2.2μ ±10, ±20 10 150 0.85±0.10 R C EMK212 B7474[]D-T X7R 0.47μ ±10, ±20 3.5 200 0.85±0.10 R/W IT EMK212 B7105[]D-T 16 X7R 1μ ±10, ±20 5 200 0.85±0.10 R O EMK212AB7225[]D-T EMK212 B7225[]D-T X7R 2.2μ ±10, ±20 5 150 0.85±0.10 R R LMK212 B7105[]D-T X7R 1μ ±10, ±20 3.5 200 0.85±0.10 R S LMK212AB7225[]D-T LMK212 B7225[]D-T 10 X7R 2.2μ ±10, ±20 5 200 0.85±0.10 R LMK212AB7475[]D-TR LMK212 B7475[]D-TR X7R 4.7μ ±10, ±20 10 150 0.85±0.10 R ●316TYPE 【Temperature Characteristic BJ : B（－25～＋85℃）/X5R（－55～＋85℃）】　1.6mm thickness（L） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg UMK316 BJ475[]L-T X5R 4.7μ ±10, ±20 10 150 1.6±0.20 R 50 UMK316BBJ106[]L-T X5R 10μ ±10, ±20 10 150 1.6±0.30 R TMK316BBJ226ML-T 25 X5R 22μ ±20 10 150 1.6±0.30 R EMK316BBJ476ML-T 16 X5R 47μ ±20 10 150 1.6±0.30 R LMK316ABJ476ML-T LMK316 BJ476ML-T 10 X5R 47μ ±20 10 150 1.6±0.20 R JMK316ABJ107ML-T JMK316 BJ107ML-T 6.3 X5R 100μ ±20 10 150 1.6±0.20 R AMK316ABJ107ML-T AMK316 BJ107ML-T X5R 100μ ±20 10 150 1.6±0.20 R 4 AMK316BBJ157ML-T X5R 150μ ±20 10 150 1.6±0.30 R PMK316BBJ227ML-T 2.5 X5R 220μ ±20 10 150 1.6±0.30 R 【Temperature Characteristic BJ : B（－25～＋85℃）/X5R（－55～＋85℃）】　0.85mm thickness（D） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg UMK316 BJ105[]D-T B X5R 1μ ±10, ±20 3.5 150 0.85±0.10 R UMK316 BJ225[]D-T 50 B X5R 2.2μ ±10, ±20 3.5 150 0.85±0.10 R UMK316ABJ475[]D-T UMK316 BJ475[]D-T X5R 4.7μ ±10, ±20 10 150 0.85±0.10 R TMK316 BJ105[]D-T B X5R 1μ ±10, ±20 3.5 200 0.85±0.10 R TMK316 BJ225[]D-T B X5R 2.2μ ±10, ±20 3.5 150 0.85±0.10 R 25 TMK316 BJ475[]D-T X5R 4.7μ ±10, ±20 5 150 0.85±0.10 R TMK316ABJ106[]D-T TMK316 BJ106[]D-TD X5R 10μ ±10, ±20 10 150 0.85±0.10 R EMK316 BJ225[]D-T B X5R 2.2μ ±10, ±20 3.5 200 0.85±0.10 R EMK316 BJ475[]D-T B X5R 4.7μ ±10, ±20 5 200 0.85±0.10 R 16 EMK316 BJ106[]D-T X5R 10μ ±10, ±20 10 150 0.85±0.10 R EMK316ABJ226MD-T EMK316 BJ226MD-T X5R 22μ ±20 10 150 0.85±0.10 R LMK316 BJ475[]D-T B X5R 4.7μ ±10, ±20 5 200 0.85±0.10 R LMK316 BJ106[]D-T 10 X5R 10μ ±10, ±20 10 200 0.85±0.10 R LMK316ABJ226MD-T LMK316 BJ226MD-T X5R 22μ ±20 10 150 0.85±0.10 R JMK316 BJ106[]D-T X5R 10μ ±10, ±20 10 200 0.85±0.10 R JMK316ABJ226MD-T JMK316 BJ226MD-T 6.3 X5R 22μ ±20 10 150 0.85±0.10 R JMK316ABJ476MD-T JMK316 BJ476MD-T X5R 47μ ±20 10 150 0.85±0.10 R 【Temperature Characteristic C6 : X6S（－55～＋105℃）】　1.6mm thickness（L） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg EMK316BC6226ML-T 16 X6S 22μ ±20 10 150 1.6±0.30 R LMK316BC6476ML-T 10 X6S 47μ ±20 10 150 1.6±0.30 R JMK316AC6476ML-T 6.3 X6S 47μ ±20 10 150 1.6±0.20 R AMK316AC6476ML-T X6S 47μ ±20 10 200 1.6±0.20 R 4 AMK316AC6107ML-T X6S 100μ ±20 10 150 1.6±0.20 R c_mlcc_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 20 20

for General Electronic Equipment ■PARTS NUMBER 【Temperature Characteristic C7 : X7S（－55～＋125℃）】　1.6mm thickness（L） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg C AMK316AC7476ML-T 4 X7S 47μ ±20 10 150 1.6±0.20 R APACER 【Temperature Characteristic B7 : X7R（－55～＋125℃）】　1.6mm thickness（L） CITAM Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg ORSIC UMK316 B7225[]L-T X7R 2.2μ ±10, ±20 10 150 1.6±0.20 R 50 UMK316AB7475[]L-T UMK316 B7475[]L-T X7R 4.7μ ±10, ±20 10 150 1.6±0.20 R GMK316AB7106[]L-TR 35 X7R 10μ ±10, ±20 10 150 1.6±0.20 R M TMK316AB7475[]L-T TMK316 B7475[]L-T X7R 4.7μ ±10, ±20 10 200 1.6±0.20 R TMK316AB7106[]L-T TMK316 B7106[]L-TD 25 X7R 10μ ±10, ±20 10 150 1.6±0.20 R U EMK316 B7475[]L-T X7R 4.7μ ±10, ±20 5 200 1.6±0.20 R LT EMK316AB7106[]L-T EMK316 B7106[]L-TD 16 X7R 10μ ±10, ±20 10 200 1.6±0.20 R IL EMK316BB7226ML-T X7R 22μ ±20 10 150 1.6±0.30 R A LMK316AB7106[]L-T LMK316 B7106[]L-TD 10 X7R 10μ ±10, ±20 10 200 1.6±0.20 R Y LMK316AB7226[]L-TR LMK316 B7226[]Ｌ-TD X7R 22μ ±10, ±20 10 150 1.6±0.20 R E R 【Temperature Characteristic B7 : X7R（－55～＋125℃）】　0.85mm thickness（D） C Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg ERA UMK316 B7225[]D-T 50 X7R 2.2μ ±10, ±20 10 150 0.85±0.10 R M TMK316AB7475[]D-T 25 X7R 4.7μ ±10, ±20 10 150 0.85±0.10 R IC LMK316AB7106MD-T 10 X7R 10μ ±20 10 150 0.85±0.10 R C A ●325TYPE P 【Temperature Characteristic BJ : B（－25～＋85℃）/X5R（－55～＋85℃）】　2.5mm thickness（M） A C Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg ITO UMK325 BJ106[]M-P 50 X5R 10μ ±10, ±20 5 150 2.5±0.20 R R GMK325 BJ226MM-P 35 X5R 22μ ±20 5 150 2.5±0.20 R S TMK325ABJ476MM-P 25 X5R 47μ ±20 10 150 2.5±0.30 R EMK325ABJ107MM-P 16 X5R 100μ ±20 10 150 2.5±0.30 R LMK325 BJ476MM-P X5R 47μ ±20 10 150 2.5±0.20 R 10 LMK325ABJ107MM-P LMK325 BJ107MM-P X5R 100μ ±20 10 150 2.5±0.30 R JMK325ABJ157MM-P X5R 150μ ±20 10 150 2.5±0.30 R JMK325ABJ227MM-P 6.3 X5R 220μ ±20 10 150 2.5±0.30 R JMK325ABJ337MM-PE X5R 330μ ±20 10 150 2.5±0.30 R AMK325ABJ157MM-P X5R 150μ ±20 10 150 2.5±0.30 R AMK325ABJ227MM-P 4 X5R 220μ ±20 10 150 2.5±0.30 R AMK325ABJ337MM-P X5R 330μ ±20 10 150 2.5±0.30 R 【Temperature Characteristic BJ : B（－25～＋85℃）/X5R（－55～＋85℃）】　1.9mm thickness（Y,N） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg UMK325 BJ475[]N-T 50 X5R 4.7μ ±10, ±20 10 150 1.9±0.20 R GMK325 BJ225[]N-T B X5R 2.2μ ±10, ±20 3.5 200 1.9±0.20 R GMK325 BJ475[]N-T 35 X5R 4.7μ ±10, ±20 10 150 1.9±0.20 R GMK325 BJ106[]N-T X5R 10μ ±10, ±20 5 150 1.9±0.20 R TMK325 BJ335MN-T B X5R*1 3.3μ ±20 3.5 200 1.9±0.20 R TMK325 BJ475[]N-T 25 B X5R*1 4.7μ ±10, ±20 3.5 200 1.9±0.20 R TMK325 BJ106[]N-T B X5R 10μ ±10, ±20 5 200 1.9±0.20 R EMK325 BJ475[]N-T B X5R*1 4.7μ ±10, ±20 3.5 200 1.9±0.20 R EMK325 BJ106[]N-T 16 X5R 10μ ±10, ±20 3.5 200 1.9±0.20 R EMK325 BJ476MY-T X5R 47μ ±20 10 150 1.9+0.1/-0.2 R LMK325 BJ226MY-T B X5R 22μ ±20 5 150 1.9+0.1/-0.2 R 10 LMK325 BJ106[]N-T X5R 10μ ±10, ±20 3.5 200 1.9±0.20 R JMK325 BJ226MY-T B X5R 22μ ±20 5 200 1.9+0.1/-0.2 R JMK325 BJ107MY-T 6.3 X5R 100μ ±20 10 150 1.9+0.1/-0.2 R JMK325 BJ476MN-T X5R 47μ ±20 10 150 1.9±0.20 R 【Temperature Characteristic BJ : B（－25～＋85℃）/X5R（－55～＋85℃）】　0.85mm thickness（D） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg TMK325 BJ106[]D-T 25 X5R 10μ ±10, ±20 5 150 0.85±0.10 R EMK325 BJ106[]D-T X5R 10μ ±10, ±20 5 150 0.85±0.10 R 16 EMK325 BJ226MD-T X5R 22μ ±20 10 150 0.85±0.10 R LMK325 BJ335[]D-T B X5R 3.3μ ±10, ±20 3.5 200 0.85±0.10 R LMK325 BJ475[]D-T 10 B X5R 4.7μ ±10, ±20 5 200 0.85±0.10 R LMK325 BJ106[]D-T X5R 10μ ±10, ±20 5 150 0.85±0.10 R 【Temperature Characteristic C6 : X6S（－55～＋105℃）】　2.5mm thickness（M） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg EMK325AC6476MM-P 16 X6S 47μ ±20 10 150 2.5±0.30 R LMK325AC6107MM-P 10 X6S 100μ ±20 10 150 2.5±0.30 R AMK325AC6157MM-P X6S 150μ ±20 10 150 2.5±0.30 R AMK325AC6227MM-P 4 X6S 220μ ±20 10 150 2.5±0.30 R AMK325AC6337MM-PE X6S 330μ ±20 10 150 2.5±0.30 R PMK325AC6337MM-P 2.5 X6S 330μ ±20 10 150 2.5±0.30 R c_mlcc_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 20 21

for General Electronic Equipment ■PARTS NUMBER 【Temperature Characteristic C7 : X7S（－55～＋125℃）】　2.5mm thickness（M） C Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg APACER JMK325AC7107MM-P 6.3 X7S 100μ ±20 10 150 2.5±0.30 R CITAM 【Temperature Characteristic B7 : X7R（－55～＋125℃）】　2.5mm thickness（M） ORSIC Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg UMK325 B7335[]M-P X7R 3.3μ ±10, ±20 3.5 200 2.5±0.20 R UMK325 B7475[]M-P 50 X7R 4.7μ ±10, ±20 5 150 2.5±0.20 R M UMK325AB7106[]M-P X7R 10μ ±10, ±20 10 150 2.5±0.30 R TMK325AB7106[]M-P X7R 10μ ±10, ±20 10 200 2.5±0.30 R U TMK325 B7226[]M-PR 25 X7R 22μ ±10, ±20 10 150 2.5±0.20 R LT EMK325 B7226[]M-PR 16 X7R 22μ ±10, ±20 10 150 2.5±0.20 R IL LMK325 B7476[]M-PR 10 X7R 47μ ±10, ±20 10 150 2.5±0.20 R A JMK325 B7476[]M-PR 6.3 X7R 47μ ±10, ±20 10 200 2.5±0.20 R Y E 【Temperature Characteristic B7 : X7R（－55～＋125℃）】　1.9mm thickness（N） R CE Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg R UMK325 B7475[]N-TR 50 X7R 4.7μ ±10, ±20 10 150 1.9±0.20 R A TMK325 B7335[]N-T X7R 3.3μ ±10, ±20 3.5 200 1.9±0.20 R M TMK325 B7475[]N-T 25 X7R 4.7μ ±10, ±20 3.5 150 1.9±0.20 R IC TMK325 B7106[]N-TR X7R 10μ ±10, ±20 10 150 1.9±0.20 R EMK325 B7475[]N-T X7R 4.7μ ±10, ±20 3.5 200 1.9±0.20 R 16 C EMK325 B7106[]N-T X7R 10μ ±10, ±20 3.5 150 1.9±0.20 R A LMK325 B7106[]N-T 10 X7R 10μ ±10, ±20 3.5 200 1.9±0.20 R P A C ●432TYPE IT 【Temperature Characteristic BJ : X5R（－55～＋85℃）】　2.5mm thickness（M） ORS Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg AMK432 BJ477MM-T 4 X5R 470μ ±20 10 150 2.5±0.20 R 【Temperature Characteristic C6 : X6S（－55～＋105℃）】　2.5mm thickness（M） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance Capacitan[c％e ]tolerance t a[％nδ] Rated vHoTltLaTge x ％Thickness*3 [mm] SRWo:R:lWdeeafrlvoinewg PMK432 C6477MM-T 2.5 X6S 470μ ±20 10 150 2.5±0.20 R c_mlcc_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 22 20

Multilayer Ceramic Capacitors ■PACKAGING ①Minimum Quantity ●Taped package Thickness Standard quantity [pcs] Type(EIA) mm code Paper tape Embossed tape □MK021(008004) 0.125 K － 50000 □VS021(008004) □MK042(01005) 0.2 C, D － 40000 □VS042(01005) 0.2 C □MK063(0201) 0.3 P,T 15000 － □WK105(0204) ※ 0.3 P 10000 － 0.13 H － 20000 0.18 E － 15000 □MK105(0402) 0.2 C 20000 － □MF105(0402) 0.3 P 15000 － 0.5 V 10000 － □VK105(0402) 0.5 W 10000 － □MK107(0603) 0.45 K 4000 － □WK107(0306) ※ 0.5 V － 4000 □MF107(0603) 0.8 A 4000 － □VS107(0603) 0.7 C 4000 － □MJ107(0603) 0.8 A 3000 3000 □MK212(0805) 0.45 K 4000 － □WK212(0508) ※ 0.85 D □MF212(0805) 1.25 G － 3000 □VS212(0805) 0.85 D 4000 － 0.85 D 4000 － □MJ212(0805) 1.25 G － 2000 0.85 D 4000 － □MK316(1206) 1.15 F － 3000 □MF316(1206) 1.6 L － 2000 1.15 F － 3000 □MJ316(1206) 1.6 L － 2000 0.85 D 1.15 F □MK325(1210) － 2000 1.9 N □MF325(1210) 2.0max. Y 2.5 M － 1000 1.9 N － 2000 □MJ325(1210) 2.5 M － 500(T), 1000(P) □MK432(1812) 2.5 M － 500 Note : ※ LW Reverse type. ②Taping material ※No bottom tape for pressed carrier tape ●Card board carrier tape ●Embossed tape Top tape Top tape Base tape Sprocket hole Sprocket hole Bottom tape Chip cavity Base tape Chip cavity ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_pack_e-E06R01

Chip filled Chip ※ LW Reverse type. ③Representative taping dimensions ●Paper Tape（8mm wide） ●Pressed carrier tape（ 2mm pitch） Unit：mm（inch） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） T A B 3.5±0.05(0.138±0.002) 8.0±0.30.315±0.012) ( T1 F 2.0±0.05 4.0±0.1 (0.079±0.002) (0.157±0.004) Chip Cavity Insertion Pitch Tape Thickness Type(EIA) Ａ Ｂ Ｆ Ｔ T1 □MK063(0201) 0.37 0.67 0.45max. 0.42max. □WK105(0204) ※ 2.0±0.05 □MK105(0402) （*1 C） 0.65 1.15 0.4max. 0.3max. □MK105(0402) （*1 P） 0.45max. 0.42max. Note *1 Thickness, C：0.2mm ,P：0.3mm. ※ LW Reverse type. Unit：mm ●Punched carrier tape （2mm pitch） Unit：mm（inch） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） T A B 3.5±0.05(0.138±0.002) 8.0±0.30.315±0.012) ( F 2.0±0.05 4.0±0.1 (0.079±0.002) (0.157±0.004) Chip Cavity Insertion Pitch Tape Thickness Type(EIA) Ａ Ｂ Ｆ Ｔ □MK105 (0402) □MF105 (0402) 0.65 1.15 2.0±0.05 0.8max. □VK105 (0402) Unit：mm ●Punched carrier tape （4mm pitch） Unit：mm（inch） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） T A B 3.5±0.050.138±0.002) 8.0±0.3315±0.012) ( 0. ( F 4.0±0.1 (0.157±0.004) 2.0±0.1 (0.079±0.004) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_pack_e-E06R01

Chip Cavity Insertion Pitch Tape Thickness Type(EIA) Ａ Ｂ Ｆ Ｔ □MK107(0603) □WK107(0306) ※ 1.0 1.8 1.1max. □MF107(0603) 4.0±0.1 □MK212(0805) 1.65 2.4 □WK212(0508) ※ 1.1max. □MK316(1206) 2.0 3.6 Note：Taping size might be different depending on the size of the product. ※ LW Reverse type. Unit：mm ●Embossed tape（4mm wide） Unit：mm（inch） φ0.8±0.04 0.9±0.05 Sprockethole (φ0.031±0.002) (0.035±0.002) A B 1.8±0.02(0.071±0.001) 4.0±0.050.157±0.002) ( F 1.0±0.02 2.0±0.04 (0.039±0.001) (0.079±0.002) Chip Cavity Insertion Pitch Tape Thickness Type(EIA) Ａ Ｂ Ｆ K T □MK021(008004) 0.135 0.27 □VS021(008004) 1.0±0.02 0.5max. 0.25max. □MK042(01005) 0.23 0.43 □VS042(01005) Unit：mm ●Embossed tape（8mm wide） Unit：mm（inch） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） A B 3.5±0.050.138±0.002) 8.0±0.3315±0.012) ( 0. ( F 4.0±0.1 (0.157±0.004) 2.0±0.1 (0.079±0.004) Chip Cavity Insertion Pitch Tape Thickness Type(EIA) Ａ Ｂ Ｆ K T □MK105(0402) 0.6 1.1 2.0±0.1 0.6max 0.2±0.1 □WK107(0306) ※ 1.0 1.8 1.3max. 0.25±0.1 □MK212(0805) 1.65 2.4 □MF212(0805) □MK316(1206) 4.0±0.1 2.0 3.6 3.4max. 0.6max. □MF316(1206) □MK325(1210) 2.8 3.6 □MF325(1210) Note： ※ LW Reverse type. Unit：mm ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_pack_e-E06R01

●Embossed tape（12mm wide） Unit：mm（inch） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） B A 5.5±0.050.217±0.002) 12.0±0.3472±0.012) ( 0. ( 4.0±0.1 2.0±0.1 (0.157±0.004) (0.079±0.004) F Chip Cavity Insertion Pitch Tape Thickness Type(EIA) Ａ Ｂ Ｆ K T □MK325(1210) 3.1 4.0 8.0±0.1 4.0max. 0.6max. □MK432(1812) 3.7 4.9 8.0±0.1 4.0max. 0.6max. Unit：mm ④Trailer and Leader Blank portion Chip cavity Blank portion Leader 160mm or more 100mm or more (6.3inches or more) (3.94inches or more) 400mm or more Direction of tape feed (15.7inches or more) ⑤Reel size t E C B A R D W A B C D E R φ178±2.0 φ50min. φ13.0±0.2 φ21.0±0.8 2.0±0.5 1.0 T W 4mm wide tape 1.5max. 5±1.0 8mm wide tape 2.5max. 10±1.5 12mm wide tape 2.5max. 14±1.5 Unit：mm ⑥Top Tape Strength The top tape requires a peel-off force of 0.1 to 0.7N in the direction of the arrow as illustrated below. Pull direction 0～20° Top tape Base tape ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_pack_e-E06R01

Super Low Distortion Multilayer Ceramic Capacitors , Medium-High Voltage Multilayer Ceramic Capacitors and High Reliability Application Multilayer Ceramic Capacitors are noted separately. Multilayer Ceramic Capacitors ■RELIABILITY DATA 1.Operating Temperature Range Temperature Standard －55 to ＋125℃ Compensating（Class1） High Frequency Type Specification Temperature Range B －25 to ＋85℃ BJ Specified X5R －55 to ＋85℃ Value B7 X7R －55 to ＋125℃ High Permittivity （Class2） C6 X6S －55 to ＋105℃ C7 X7S －55 to ＋125℃ LD(※) X5R －55 to ＋85℃ Note: ※LD Low distortion high value multilayer ceramic capacitor 2. Storage Conditions Temperature Standard －55 to ＋125℃ Compensating（Class1） High Frequency Type Specification Temperature Range B －25 to ＋85℃ Specified BJ X5R －55 to ＋85℃ Value B7 X7R －55 to ＋125℃ High Permittivity （Class2） C6 X6S －55 to ＋105℃ C7 X7S －55 to ＋125℃ LD(※) X5R －55 to ＋85℃ Note: ※LD Low distortion high value multilayer ceramic capacitor 3. Rated Voltage Temperature Standard 50VDC, 25VDC, 16VDC Specified Compensating（Class1） High Frequency Type 50VDC, 25VDC, 16VDC Value High Permittivity （Class2） 50VDC, 35VDC, 25VDC, 16VDC, 10VDC, 6.3VDC, 4VDC, 2.5VDC 4. Withstanding Voltage （Between terminals） Temperature Standard Specified Compensating（Class1） High Frequency Type No breakdown or damage Value High Permittivity （Class2） Class 1 Class 2 Test Applied voltage Rated voltage×3 Rated voltage×2.5 Methods and Duration 1 to 5 sec. Remarks Charge/discharge current 50mA max. 5. Insulation Resistance Temperature Standard 10000 MΩ min. Compensating（Class1） High Frequency Type Specified Value C≦0.047 High Permittivity （Class2） Note 1 F : 10000 MΩ min. C＞0.047μF : 500MΩ・μF Test Applied voltage : Rated voltage Methods and Duration : 60±5 sec. Remarks Charge/discharge current : 50mA max. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_reli_e-E08R01

6. Capacitance （Tolerance） 0.2pF≦C≦5pF : ±0.25pF C□ Standard 0.2pF≦C≦10pF : ±0.5pF Temperature U□ C＞10pF : ±5% or ±10% Specified Compensating（Class1） Value 0.2pF≦C≦2pF : ±0.1pF High Frequency Type CG C＞2pF : ±5% High Permittivity （Class2） ±10% or ±20% Class 1 Class 2 Standard High Frequency Type C≦10μF C＞10μF Test Preconditioning None Thermal treatment （at 150℃ for 1hr） Note 2 Methods and Measuring frequency 1ＭHz±10% 1kHz±10% 120±10Hz Remarks Measuring voltage Nte 0.5 to 5Vrms 1±0.2Vrms 0.5±0.1Vrms Bias application None 7. Q or Dissipation Factor C＜30pF : Q≧400＋20C Temperature Standard C≧30pF : Q≧1000 （C：Nominal capacitance） Specified Compensating（Class1） Value High Frequency Type Refer to detailed specification High Permittivity （Class2） Note 1 BJ, B7, C6, C7：2.5% max. Class 1 Class 2 Standard High Frequency Type C≦10μF C＞10μF Preconditioning None Thermal treatment （at 150℃ for 1hr） Note 2 Test Measuring frequency 1ＭHz±10% 1GHz 1ｋHz±10% 120±10Hz Methods and Measuring voltage Note 1 0.5 to 5Vrms 1±0.2Vrms 0.5±0.1Vrms Remarks Bias application None High Frequency Type Measuring equipment : HP4291A Measuring jig : HP16192A 8. Temperature Characteristic （Without voltage application） Temperature Characteristic ［ppm/℃］ Tolerance ［ppm/℃］ C□ : 0 CG G : ±30 Standard Temperature J：±120 U□ : －750 UJ, UK Compensating（Class1） K：±250 Temperature Characteristic ［ppm/℃］ Tolerance ［ppm/℃］ High Frequency Type C□ : 0 CG G : ±30 Specified Capacitance Reference Specification Temperature Range Value change temperature B ±10% 20℃ －25 to ＋85℃ BJ X5R ±15% 25℃ －55 to ＋85℃ High Permittivity （Class2） B7 X7R ±15% 25℃ －55 to ＋125℃ C6 XS ±22% 25℃ －55 to ＋105℃ C7 X7S ±22% 25℃ －55 to ＋125℃ LD(※) X5R ±15% 25℃ －55 to ＋85℃ Note : ※LD Low distortion high value multilayer ceramic capacitor Class 1 Capacitance at 20℃ and 85℃ shall be measured in thermal equilibrium, and the temperature characteristic shall be calculated from the following equation. （C －C ） 85 20 ×106（ppm/℃） C ×△T △T＝65 20 Class 2 Test Capacitance at each step shall be measured in thermal equilibrium, and the temperature characteristic shall be calculated from the following Methods and equation. Remarks Step B X5R、X7R、X6S、X7S 1 Minimum operating temperature 2 20℃ 25℃ 3 Maximum operating temperature （C－C） C ：Capacitance in Step 1 or Step 3 2 ×100（%） C C ：Capacitance in Step 2 2 2 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_reli_e-E08R01

9. Deflection Appearance : No abnormality Standard Temperature Capacitance change : Within ±5% or ±0.5 pF, whichever is larger. Specified Compensating（Class1） Appearance : No abnormality High Frequency Type Value Capacitance change : Within±0.5 pF Appearance : No abnormality High Permittivity （Class2） Capacitance change : Within ±12.5% Multilayer Ceramic Capacitors 021, 042, 063, ※105 Type The other types Board Glass epoxy-resin substrate Test Thickness 0.8mm 1.6mm Methods and Warp 1mm Remarks Duration 10 sec. ※105 Type thickness, C： 0.2mm ,P： 0.3mm. Capacitance measurement shall be conducted with the board bent 10. Body Strength Temperature Standard － Specified Compensating（Class1） High Frequency Type No mechanical damage. Value High Permittivity （Class2） － High Frequency 105Type Applied force : 5N Test Duraton : 10 sec. Methods and Remarks 11. Adhesive Strength of Terminal Electrodes Temperature Standard Specified Compensating（Class1） High Frequency Type No terminal separation or its indication. Value High Permittivity （Class2） Multilayer Ceramic Capacitors Test 021, 042, 063 Type 105 Type or more Methods and Applied force 2N 5N Remarks Duration 30±5 sec. 12. Solderability Temperature Standard Specified Compensating（Class1） High Frequency Type At least 95% of terminal electrode is covered by new solder. Value High Permittivity （Class2） Eutectic solder Lead-free solder Test Solder type H60A or H63A Sn-3.0Ag-0.5Cu Methods and Solder temperature 230±5℃ 245±3℃ Remarks Duration 4±1 sec. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_reli_e-E08R01

13. Resistance to Soldering Appearance : No abnormality Capacitance change : Within ±2.5% or ±0.25pF, whichever is larger. Standard Q : Initial value Insulation resistance : Initial value Temperature Withstanding voltage （between terminals） : No abnormality Compensating（Class1） Appearance : No abnormality Capacitance change : Within ±2.5% Specified High Frequency Type Q : Initial value Value Insulation resistance : Initial value Withstanding voltage （between terminals） : No abnormality Appearance : No abnormality Capacitance change : Within ±7.5% High Permittivity （Class2） Note 1 Dissipation factor : Initial value Insulation resistance : Initial value Withstanding voltage （between terminals）: No abnormality Class 1 021, 042, 063 Type 105 Type Preconditioning None 80 to 100℃, 2 to 5 min. Preheating 150℃, 1 to 2 min. 150 to 200℃, 2 to 5 min. Solder temp. 270±5℃ Duration 3±0.5 sec. Test Recovery 6 to 24 hrs （Standard condition） Note 5 Methods and Remarks Class 2 021, 042、063 Type 105, 107, 212 Type 316, 325, 432 Type Preconditioning Thermal treatment （at 150℃ for 1 hr） Note 2 80 to 100℃, 2 to 5 min. 80 to 100℃, 5 to 10 min. Preheating 150℃, 1 to 2 min. 150 to 200℃, 2 to 5 min. 150 to 200℃, 5 to 10 min. Solder temp. 270±5℃ Duration 3±0.5 sec. Recovery 24±2 hrs （Standard condition） Note 5 14. Temperature Cycle (Thermal Shock） Appearance : No abnormality Capacitance change : Within ±2.5% or ±0.25pF, whichever is larger. Standard Q : Initial value Insulation resistance : Initial value Temperature Withstanding voltage （between terminals） : No abnormality Compensating（Class1） Appearance : No abnormality Capacitance change : Within ±0.25pF Specified High Frequency Type Q : Initial value Value Insulation resistance : Initial value Withstanding voltage （between terminals） : No abnormality Appearance : No abnormality Capacitance change : Within ±7.5% High Permittivity （Class2） Note 1 Dissipation factor : Initial value Insulation resistance : Initial value Withstanding voltage （between terminals） : No abnormality Class 1 Class 2 Thermal treatment （at 150℃ for 1 hr） Preconditioning None Note 2 Step Temperature（℃） Time（min.） Test 1 Minimum operating temperature 30±3 Methods and 1 cycle 2 Normal temperature 2 to 3 Remarks 3 Maximum operating temperature 30±3 4 Normal temperature 2 to 3 Number of cycles 5 times Recovery 6 to 24 hrs （Standard condition） Note 5 24±2 hrs （Standard condition） Note 5 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_reli_e-E08R01

15. Humidity （Steady State） Appearance : No abnormality Capacitance change : Within ±5% or ±0.5pF, whichever is larger. Q : C＜10pF : Q≧200＋10C Standard 10≦C＜30pF : Q≧275＋2.5C Temperature C≧30pF:Q≧350（C：Nominal capacitance） Compensating（Class1） Insulation resistance : 1000 MΩ min. Specified Appearance : No abnormality Value High Frequency Type Capacitance change : Within ±0.5pF, Insulation resistance : 1000 MΩ min. Appearance : No abnormality Capacitance change : Within ±12.5% High Permittivity （Class2） Note 1 Dissipation factor : 5.0% max. Insulation resistance : 50 MΩμF or 1000 MΩ whichever is smaller. Class 1 Class 2 Standard High Frequency Type All items Test Preconditioning None Thermal treatment（ at 150℃ for 1 hr） Note 2 Methods and Temperature 40±2℃ 60±2℃ 40±2℃ Remarks Humidity 90 to 95%RH 90 to 95%RH Duration 500＋24/－0 hrs 500＋24/－0 hrs Recovery 6 to 24 hrs （Standard condition） Note 5 24±2 hrs （Standard condition） Note 5 16. Humidity Loading Appearance : No abnormality Capacitance change : Within ±7.5% or ±0.75pF, whichever is larger. Standard Q : C＜30pF：Q≧100＋10C/3 C≧30pF：Q≧200 （C：Nominal capacitance） Temperature Insulation resistance : 500 MΩ min. Compensating（Class1） Appearance : No abnormality Specified Capacitance change : C≦2pF：Within ±0.4 pF Value High Frequency Type C＞2pF：Within ±0.75 pF （C：Nominal capacitance） Insulation resistance : 500 MΩ min. Appearance : No abnormality Capacitance change : Within ±12.5% High Permittivity （Class2） Note 1 Dissipation factor : 5.0% max. Insulation resistance : 25 MΩμF or 500 MΩ, whichever is smaller. Class 1 Class 2 Standard High Frequency Type All items Preconditioning Voltage treatment None （Rated voltage are applied for 1 hour at 40℃） Note 3 Test Temperature 40±2℃ 60±2℃ 40±2℃ Methods and Humidity 90 to 95%RH 90 to 95%RH Remarks Duration 500＋24/－0 hrs 500＋24/－0 hrs Applied voltage Rated voltage Rated voltage Charge/discharge 50mA max. 50mA max. current Recovery 6 to 24 hrs （Standard condition） Note 5 24±2 hrs（Standard condition） Note 5 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_reli_e-E08R01

17. High Temperature Loading Appearance : No abnormality Capacitance change : Within ±3% or ±0.3pF, whichever is larger. Q : C＜10pF： Q≧200＋10C Standard 10≦C＜30pF：Q≧275＋2.5C Temperature C≧30pF： Q≧350（C：Nominal capacitance） Compensating（Class1） Insulation resistance : 1000 MΩ min. Specified Appearance : No abnormality Value High Frequency Type Capacitance change : Within ±3% or ±0.3pF, whichever is larger. Insulation resistance : 1000 MΩ min. Appearance : No abnormality Capacitance change : Within ±12.5% High Permittivity （Class2） Note 1 Dissipation factor : 5.0% max. Insulation resistance : 50 MΩμF or 1000 MΩ, whichever is smaller. Class 1 Class 2 Standard High Frequency Type BJ, LD(※) C6 B7, C7 Voltage treatment（Twice the rated voltage shall be applied for Preconditioning None 1 hour at 85℃, 105℃ or 125℃） Note 3, 4 Temperature Maximum operating temperature Maximum operating temperature Test Duration 1000＋48/－0 hrs 1000＋48/－0 hrs Methods and Applied voltage Rated voltage×2 Note 4 Rated voltage×2 Note 4 Remarks Charge/discharge 50mA max. 50mA max. current Recovery 6 to 24hr （Standard condition） Note 5 24±2 hrs （Standard condition） Note 5 Note: ※LD Low distortion high value multilayer ceramic capacitor Note 1 The figures indicate typical specifications. Please refer to individual specifications in detail. Note 2 Thermal treatment : Initial value shall be measured after test sample is heat-treated at 150＋0/－10℃ for an hour and kept at room temperature for 24±2hours. Note 3 Voltage treatment : Initial value shall be measured after test sample is voltage-treated for an hour at both the temperature and voltage specified in the test conditions, and kept at room temperature for 24±2hours. Note 4 150% of rated voltage is applicable to some items. Please refer to their specifications for further information. Note 5 Standard condition: Temperature: 5 to 35℃, Relative humidity: 45 to 85 % RH, Air pressure: 86 to 106kPa When there are questions concerning measurement results, in order to provide correlation data, the test shall be conducted under the following condition. Temperature: 20±2℃, Relative humidity: 60 to 70 % RH, Air pressure: 86 to 106kPa Unless otherwise specified, all the tests are conducted under the "standard condition". ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_reli_e-E08R01

High Reliability Application Multilayer Ceramic Capacitors are noted separately. Precautions on the use of Multilayer Ceramic Capacitors ■PRECAUTIONS 1. Circuit Design ◆Verification of operating environment, electrical rating and performance 1. A malfunction of equipment in fields such as medical, aerospace, nuclear control, etc. may cause serious harm to human life or have severe social ramifications. Therefore, any capacitors to be used in such equipment may require higher safety and reliability, and shall be clearly differentiated from them used in general purpose applications. Precautions ◆Operating Voltage （Verification of Rated voltage） 1. The operating voltage for capacitors must always be their rated voltage or less. If an AC voltage is loaded on a DC voltage, the sum of the two peak voltages shall be the rated voltage or less. For a circuit where an AC or a pulse voltage may be used, the sum of their peak voltages shall also be the rated voltage or less. 2. Even if an applied voltage is the rated voltage or less reliability of capacitors may be deteriorated in case that either a high frequency AC voltage or a pulse voltage having rapid rise time is used in a circuit. 2. PCB Design ◆Pattern configurations （Design of Land-patterns） 1. When capacitors are mounted on PCBs, the amount of solder used （size of fillet） can directly affect the capacitor performance. Therefore, the following items must be carefully considered in the design of land patterns: （1）Excessive solder applied can cause mechanical stresses which lead to chip breaking or cracking. Therefore, please consider appropriate land-patterns for proper amount of solder. Precautions （2）When more than one component are jointly soldered onto the same land, each component's soldering point shall be separated by solder-resist. ◆Pattern configurations （Capacitor layout on PCBs） After capacitors are mounted on boards, they can be subjected to mechanical stresses in subsequent manufacturing processes （PCB cutting, board inspection, mounting of additional parts, assembly into the chassis, wave soldering of the boards, etc.）. For this reason, land pattern configurations and positions of capacitors shall be carefully considered to minimize stresses. ◆Pattern configurations （Design of Land-patterns） The following diagrams and tables show some examples of recommended land patterns to prevent excessive solder amounts. （1）Recommended land dimensions for typical chip capacitors ●Multilayer Ceramic Capacitors : Recommended land dimensions Land patterns for PCBs （unit: mm） Land pattern Wave-soldering Chip capacitor Solder-resist Type 107 212 316 325 L 1.6 2.0 3.2 3.2 Size C W 0.8 1.25 1.6 2.5 A 0.8 to 1.0 1.0 to 1.4 1.8 to 2.5 1.8 to 2.5 B 0.5 to 0.8 0.8 to 1.5 0.8 to 1.7 0.8 to 1.7 B A B C 0.6 to 0.8 0.9 to 1.2 1.2 to 1.6 1.8 to 2.5 Chip capacitor W Technical L considerations Reflow-soldering Type 021 042 063 105 107 212 316 325 432 L 0.25 0.4 0.6 1.0 1.6 2.0 3.2 3.2 4.5 Size W 0.125 0.2 0.3 0.5 0.8 1.25 1.6 2.5 3.2 A 0.095～0.135 0.15～0.25 0.20～0.30 0.45～0.55 0.6～0.8 0.8～1.2 1.8～2.5 1.8～2.5 2.5～3.5 B 0.085～0.125 0.10～0.20 0.20～0.30 0.40～0.50 0.6～0.8 0.8～1.2 1.0～1.5 1.0～1.5 1.5～1.8 C 0.110～0.150 0.15～0.30 0.25～0.40 0.45～0.55 0.6～0.8 0.9～1.6 1.2～2.0 1.8～3.2 2.3～3.5 Note：Recommended land size might be different according to the allowance of the size of the product. ●LWDC: Recommended land dimensions for reflow-soldering LWDC （unit: mm） Type 105 107 212 L 0.52 0.8 1.25 Size W W 1.0 1.6 2.0 A 0.18～0.22 0.25～0.3 0.5～0.7 B 0.2～0.25 0.3～0.4 0.4～0.5 C 0.9～1.1 1.5～1.7 1.9～2.1 L ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_prec_e-E08R01

（2）Examples of good and bad solder application Item Not recommended Recommended Lead wire of component Solder-resist Mixed mounting of SMD and leaded components Chassis Solder (for grounding) Solder-resist Component placement close to the chassis Electrode pattern Lead wire of component Soldering iron Hand-soldering of leaded Solder-resist components near mounted components Solder-resist Horizontal component placement ◆Pattern configurations （Capacitor layout on PCBs） 1-1. The following is examples of good and bad capacitor layouts ; capacitors shall be located to minimize any possible mechanical stresses from board warp or deflection. Items Not recommended Recommended Place the product at a right angle to the direction of the Deflection of board anticipated mechanical stress. 1-2. The amount of mechanical stresses given will vary depending on capacitor layout. Please refer to diagram below. E D Perforation C A B Slit Magnitude of stress A＞B＝C＞D＞E 1-3. When PCB is split, the amount of mechanical stress on the capacitors can vary according to the method used. The following methods are listed in order from least stressful to most stressful: push-back, slit, V-grooving, and perforation. Thus, please consider the PCB, split methods as well as chip location. 3. Mounting ◆Adjustment of mounting machine 1. When capacitors are mounted on PCB, excessive impact load shall not be imposed on them. 2. Maintenance and inspection of mounting machines shall be conducted periodically. ◆Selection of Adhesives Precautions 1. When chips are attached on PCBs with adhesives prior to soldering, it may cause capacitor characteristics degradation unless the following factors are appropriately checked : size of land patterns, type of adhesive, amount applied, hardening temperature and hardening period. Therefore, please contact us for further information. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_prec_e-E08R01

◆Adjustment of mounting machine 1. When the bottom dead center of a pick-up nozzle is too low, excessive force is imposed on capacitors and causes damages. To avoid this, the following points shall be considerable. （1）The bottom dead center of the pick-up nozzle shall be adjusted to the surface level of PCB without the board deflection. （2）The pressure of nozzle shall be adjusted between 1 and 3 N static loads. （3）To reduce the amount of deflection of the board caused by impact of the pick-up nozzle, supporting pins or back-up pins shall be used on the other side of the PCB. The following diagrams show some typical examples of good and bad pick-up nozzle placement: Item Improper method Proper method chipping Single-sided mounting or cracking supporting pins or back-up pins Double-sided mounting chipping supporting pins or cracking or back-up pins 2. As the alignment pin is worn out, adjustment of the nozzle height can cause chipping or cracking of capacitors because of mechanical Technical impact on the capacitors. considerations To avoid this, the monitoring of the width between the alignment pins in the stopped position, maintenance, check and replacement of the pin shall be conducted periodically. ◆Selection of Adhesives Some adhesives may cause IR deterioration. The different shrinkage percentage of between the adhesive and the capacitors may result in stresses on the capacitors and lead to cracking. Moreover, too little or too much adhesive applied to the board may adversely affect components. Therefore, the following precautions shall be noted in the application of adhesives. （1）Required adhesive characteristics a. The adhesive shall be strong enough to hold parts on the board during the mounting & solder process. b. The adhesive shall have sufficient strength at high temperatures. c. The adhesive shall have good coating and thickness consistency. d. The adhesive shall be used during its prescribed shelf life. e. The adhesive shall harden rapidly. f. The adhesive shall have corrosion resistance. g. The adhesive shall have excellent insulation characteristics. h. The adhesive shall have no emission of toxic gasses and no effect on the human body. （2）The recommended amount of adhesives is as follows; ［Recommended condition］ Amount adhesive After capacitor are bonded Figure 212/316 case sizes as examples a a a 0.3mm min b b 100 to 120μm c Adhesives shall not contact land c c 4. Soldering ◆Selection of Flux Since flux may have a significant effect on the performance of capacitors, it is necessary to verify the following conditions prior to use; （1）Flux used shall be less than or equal to 0.1 wt%（ in Cl equivalent） of halogenated content. Flux having a strong acidity content shall not be applied. （2）When shall capacitors are soldered on boards, the amount of flux applied shall be controlled at the optimum level. Precautions （3）When water-soluble flux is used, special care shall be taken to properly clean the boards. ◆Soldering Temperature, time, amount of solder, etc. shall be set in accordance with their recommended conditions. Sn-Zn solder paste can adversely affect MLCC reliability. Please contact us prior to usage of Sn-Zn solder. ◆Selection of Flux 1-1. When too much halogenated substance（Chlorine, etc.） content is used to activate flux, or highly acidic flux is used, it may lead to corrosion of terminal electrodes or degradation of insulation resistance on the surfaces of the capacitors. 1-2. Flux is used to increase solderability in wave soldering. However if too much flux is applied, a large amount of flux gas may be emitted Technical and may adversely affect the solderability. To minimize the amount of flux applied, it is recommended to use a flux-bubbling system. considerations 1-3. Since the residue of water-soluble flux is easily dissolved in moisture in the air, the residues on the surfaces of capacitors in high humidity conditions may cause a degradation of insulation resistance and reliability of the capacitors. Therefore, the cleaning methods and the capability of the machines used shall also be considered carefully when water-soluble flux is used. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_prec_e-E08R01

◆Soldering ･ Ceramic chip capacitors are susceptible to thermal shock when exposed to rapid or concentrated heating or rapid cooling. ･ Therefore, the soldering must be conducted with great care so as to prevent malfunction of the components due to excessive thermal shock. ･ Preheating : Capacitors shall be preheated sufficiently, and the temperature difference between the capacitors and solder shall be within 130℃. ･ Cooling : The temperature difference between the capacitors and cleaning process shall not be greater than 100℃. ［Reflow soldering］ 【Recommended conditions for eutectic 【Recommended condition for Pb-free soldering】 soldering】 300 300 Preheating 230℃ Peak Within 10sec. 260℃ Max. ℃） 200 60Msine.c . 6M0sine.c ℃） 200 Within 10sec. mperature（ 100 Slow cooling mperature（ 100 cSoololiwn g Te Te Preheating150℃ Heating above 60sec. Min. 230℃ 0 0 40sec. Max. 1/2T～1/3T Caution Capacitor ①The ideal condition is to have solder mass（fillet）controlled to 1/2 to 1/3 of the Solder T thickness of a capacitor. PC board ②Because excessive dwell times can adversely affect solderability, soldering duration shall be kept as close to recommended times as possible. soldering for 2 times. ［Wave soldering］ 【Recommended conditions for eutectic 【Recommended condition for Pb-free soldering】 soldering】 300 300 230～250℃ Peak Preheating Within 3sec. 260℃ Max. ℃） 200 120sec. Min. ℃） 200 120sec. Min. Within 10sec. mperature（ 100 Slow cooling mperature（ 100 P15re0h℃ea ting cSoololiwng Te Te 0 0 Caution ①Wave soldering must not be applied to capacitors designated as for reflow soldering only. soldering for 1 times. ［Hand soldering］ 【Recommended conditions for eutectic 【Recommended condition for Pb-free soldering】 soldering】 400 400 400 230～280℃ Peak Peak Within 3sec. 350℃ Max. 280℃ Max. Within 3sec. Within 3sec. 300 300 300 Temperature（℃） 210000 Slow cooling Temperature（℃） 210000 ⊿T P15re0h℃ea tMiningS. low cooling 温度（℃） 210000 ⊿T P15re0h℃ea tMinSinglo. w cooling Preheating 0 60sec. Min. 0 60sec. Min. 0 60sec. Min. ⊿T ⊿T 316type or less ⊿T≦150℃ 325type or more ⊿T≦130℃ Caution ①Use a 50W soldering iron with a maximum tip diameter of 1.0 mm. ②The soldering iron shall not directly touch capacitors. soldering for 1 times. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_prec_e-E08R01

5. Cleaning ◆Cleaning conditions 1. When PCBs are cleaned after capacitors mounting, please select the appropriate cleaning solution in accordance with the intended use Precautions of the cleaning. （e.g. to remove soldering flux or other materials from the production process.） 2. Cleaning condition shall be determined after it is verified by using actual cleaning machine that the cleaning process does not affect capacitor's characteristics. 1. The use of inappropriate cleaning solutions can cause foreign substances such as flux residue to adhere to capacitors or deteriorate their outer coating, resulting in a degradation of the capacitor's electrical properties （especially insulation resistance）. 2. Inappropriate cleaning conditions（ insufficient or excessive cleaning） may adversely affect the performance of the capacitors. Technical In the case of ultrasonic cleaning, too much power output can cause excessive vibration of PCBs which may lead to the cracking of considerations capacitors or the soldered portion, or decrease the terminal electrodes' strength. Therefore, the following conditions shall be carefully checked; Ultrasonic output : 20 W/ℓ or les Ultrasonic frequency : 40 kHz or less Ultrasonic washing period : 5 min. or less 6. Resin coating and mold 1. With some type of resins, decomposition gas or chemical reaction vapor may remain inside the resin during the hardening period or while left under normal storage conditions resulting in the deterioration of the capacitor's performance. Precautions 2. When a resin's hardening temperature is higher than capacitor's operating temperature, the stresses generated by the excessive heat may lead to damage or destruction of capacitors. The use of such resins, molding materials etc. is not recommended. 7. Handling ◆Splitting of PCB 1. When PCBs are split after components mounting, care shall be taken so as not to give any stresses of deflection or twisting to the board. 2. Board separation shall not be done manually, but by using the appropriate devices. Precautions ◆Mechanical considerations Be careful not to subject capacitors to excessive mechanical shocks. （1）If ceramic capacitors are dropped onto a floor or a hard surface, they shall not be used. （2）Please be careful that the mounted components do not come in contact with or bump against other boards or components. 8. Storage conditions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep packaging materials in good condition, care must be taken to control temperature and humidity in the storage area. Humidity should especially be kept as low as possible. ・Recommended conditions Ambient temperature : Below 30℃ Humidity : Below 70% RH Precautions The ambient temperature must be kept below 40℃. Even under ideal storage conditions, solderability of capacitor is deteriorated as time passes, so capacitors shall be used within 6 months from the time of delivery. ・Ceramic chip capacitors shall be kept where no chlorine or sulfur exists in the air. 2. The capacitance values of high dielectric constant capacitors will gradually decrease with the passage of time, so care shall be taken to design circuits. Even if capacitance value decreases as time passes, it will get back to the initial value by a heat treatment at 150℃ for 1hour. If capacitors are stored in a high temperature and humidity environment, it might rapidly cause poor solderability due to terminal oxidation and Technical quality loss of taping/packaging materials. For this reason, capacitors shall be used within 6 months from the time of delivery. If exceeding the considerations above period, please check solderability before using the capacitors. ※RCR-2335B（Safety Application Guide for fixed ceramic capacitors for use in electronic equipment）is published by JEITA. Please check the guide regarding precautions for deflection test, soldering by spot heat, and so on. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_prec_e-E08R01