5.0V Surface Mount Crystal Clock Oscillator HSM9 Features: XO 1.0 to 80 MHz The Connor-Winfield HSM91, HSM92, 5.0V Operation 2111 Comprehensive Drive 2111 Comprehensive Drive HSM93, and HSM94 models are RoHS Compliant AAuurroorraa,, IIlllliinnooiiss 6600550055 7.5mm x 5mm, 5.0V HCMOS, Surface Mount, Tri-State Enable / Disable Phone: 630-851-4722 Fixed Frequency Crystal Oscillators (XO) Phone: 630-851-4722 Overall Frequency Tolerance: designed for use in all applications requiring Fax: 630-851-5040 HSM94 ± 20 ppm, HSM91 ± 25 ppm Fax: 630-851-5040 precision clocks. The RoHS compliant surface HSM92 ± 50 ppm, HSM93 ± 100 ppm www.conwin.com mount package is designed for high-density www.conwin.com Temperature Range: 0 to 70°C mounting and is optimum for mass US Headquarters: Ceramic Surface Mount Package production. 630-851-4722 Tape and Reel Packaging European Headquarters: +353-61-472221 Absolute Maximum Ratings Parameter Minimum Nominal Maximum Units Notes Storage Temperature -55 - 125 °C Supply Voltage (Vcc) -0.5 - 7.0 Vdc Operating Specifications Parameter Minimum Nominal Maximum Units Notes Frequency Range (Fo) - 80 MHz HSM94 1.8 HSM91 1.0 HSM92 1.0 HSM93 1.0 Frequency Tolerance - ppm 1 HSM94 -20 20 HSM91 -25 25 HSM92 -50 50 HSM93 -100 100 Operating Temp Range 0 - 70 °C Supply Voltage (Vdd) 4.5 5.0 5.5 Vdc Supply Current (Icc) - - mA 1.0 to 31.999 MHz 27 32 to 49.999 MHz 45 50 to 80.0 MHz 75 Input Characteristics Parameter Minimum Nominal Maximum Units Notes Enable Voltage - (Vih) ≥ 70% Vdd - - Vdc 2 Disable Voltage - (Vil) - - ≤ 30% Vdd Vdc Enable Time - - 100 mS Disable Time - - 100 nS HCMOS Output Characteristics Parameter Minimum Nominal Maximum Units Notes Load - - 50 pF High (Voh) 4.5 - - Voltage Low (Vol) - - 0.55 Vdc High (loh) -16 - - Current Low (lol) - - 16 mA Duty Cycle at 50% of Vcc 45 50 55 % Rise / Fall Time 10% to 90% - - 6 nS Start-Up Time - - 10 mS Bulletin Sm006 Jitter - - 5 pS RMS Page 1 of 2 Notes: Revision 27 1.Inclusive of calibration @ 25°C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging. 2.Oscillator output is enabled with no connection on pad 1 Date 07 May 2008 Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation

2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630-851-4722 Fax: 630-851-5040 www.conwin.com Package Characteristics Suggested Pad Layout Package Hermetically sealed ceramic package and metal cover Environmental Characteristics Temperature Cycle The specimen shall meet electrical characteristics after tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes Hermetical No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes Solvent Resistance Marking will withstand immersion in Isopropyl Alcohol or Trichloroethylene Soldering Bypass capacitor, C-by, should be General Conditions 260°C max x 10 sec max x 2 times max or ceramic capacitor ≥ .01 uf 230°C max x 180 sec max x 1 time Typical Operation Data (Vapor phase reflow) Test Circuit 20 to 100 sec up to 215°C, 50 sec at 215°C, then down to room temperature per 1 to 5°C / sec OSCILLOSCOPE Vcc Mechanical Characteristics POWER PROBE SUPPLY Free Drop The specimen shall meet electrical characteristics after tested 3 times, Free Drop testing on the hard wooden board from a height of 75 cm. OSC .01uf Vibration The specimen shall meet electrical characteristics after tested by the following conditions: 10-55Hz 1.5mm Amplitude, FREQ 55-2000 Hz 20 G's, 2 hours for each plane INPUT FOR E/D COUNTER Thermal Shock After applied Thermal Shock of 260°C max x 10 sec max x 2 times, or 230°C max x 180 sec max, Output Waveform the specimen shall meet electrical characteristics Solderability (EIAJ-RCX-0102.101 Condition 1a) 1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%) 2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%) 3) Solder bath temperature: 235°C ±5°C 4) Depth of immersion: Up to electrical terminal 5) Immersing time: Within 2 sec ±0.5 sec into solder bath AAAAAfffffttttteeeeerrrrr pppppeeeeerrrrrfffffooooorrrrrmmmmmiiiiinnnnnggggg ttttthhhhheeeee aaaaabbbbbooooovvvvveeeee ppppprrrrroooooccccceeeeeddddduuuuurrrrreeeeesssss,,,,, aaaaa nnnnneeeeewwwwwlllllyyyyy sssssooooollllldddddeeeeerrrrreeeeeddddd cccccooooovvvvveeeeerrrrraaaaagggggeeeee ssssshhhhhaaaaallllllllll bbbbbeeeee gggggrrrrreeeeeaaaaattttteeeeerrrrr ttttthhhhhaaaaannnnn 9999900000%%%%% SYMMETRY Pin Connections 1:Tri-State E/D 2:Ground 3:Output 4:VDD Tape and Reel Dimensions Ordering Information HSM91 - 050.0M CLOCK CENTER SERIES FREQUENCY Dimensional Tolerance: ±.02" (.508mm) ±.005"(.127mm) Bulletin Sm006 Page 2 of 2 Meets EIA-481A and EIAJ-1009B Revision 27 2,000 PCS/Reel Date 07 May 2008 Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation