Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product Information in this Catalog (4) Power generation control equipment (nuclear power, Product information in this catalog is as of October 2019. All of the hydroelectric power, thermal power plant control system, etc.) contents specified herein and production status of the products listed (5) Undersea equipment (submarine repeating equipment, in this catalog are subject to change without notice due to technical underwater work equipment, etc.) improvement of our products, etc. Therefore, please check for the (6) Military equipment latest information carefully before practical application or use of our (7) Any other equipment requiring extremely high levels of safety products. and/or reliability equal to the equipment listed above Please note that TAIYO YUDEN shall not be in any way responsible *Notes: for any damages and defects in products or equipment incorporating 1. There is a possibility that our products can be used only our products, which are caused under the conditions other than those for aviation equipment that does not directly affect the safe specified in this catalog or individual product specification sheets. operation of aircraft (e.g., in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets ■ Approval of Product Specifications requirements specified separately by TAIYO YUDEN. Please Please contact TAIYO YUDEN for further details of product be sure to contact TAIYO YUDEN for further information specifications as the individual product specification sheets are before using our products for such aviation equipment. available. When using our products, please be sure to approve our 2. Implantable medical devices contain not only internal unit product specifications or make a written agreement on the product which is implanted in a body, but also external unit which is specification with TAIYO YUDEN in advance. connected to the internal unit. ■ Pre-Evaluation in the Actual Equipment and Conditions 4. Limitation of Liability Please conduct validation and verification of our products in actual Please note that unless you obtain prior written consent of TAIYO conditions of mounting and operating environment before using our YUDEN, TAIYO YUDEN shall not be in any way responsible for products. any damages incurred by you or third parties arising from use of the products listed in this catalog for any equipment that is not ■ Limited Application intended for use by TAIYO YUDEN, or any equipment requiring 1. Equipment Intended for Use inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN The products listed in this catalog are intended for general- as described above. purpose and standard use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office ■ Safety Design equipment, information and communication equipment including, When using our products for high safety and/or reliability-required without limitation, mobile phone, and PC) and other equipment equipment or circuits, please fully perform safety and/or reliability specified in this catalog or the individual product specification sheets. evaluation. In addition, please install (i) systems equipped with a protection circuit and a protection device and/or (ii) systems TAIYO YUDEN has the line-up of the products intended for equipped with a redundant circuit or other system to prevent an use in automotive electronic equipment, telecommunications unsafe status in the event of a single fault for a failsafe design to infrastructure and industrial equipment, or medical devices ensure safety. classified as GHTF Classes A to C (Japan Classes I to III). Therefore, when using our products for these equipment, ■ Intellectual Property Rights please check available applications specified in this catalog Information contained in this catalog is intended to convey examples or the individual product specification sheets and use the of typical performances and/or applications of our products and is corresponding products. not intended to make any warranty with respect to the intellectual property rights or any other related rights of TAIYO YUDEN or any 2. Equipment Requiring Inquiry third parties nor grant any license under such rights. Please be sure to contact TAIYO YUDEN for further information before using the products listed in this catalog for the following ■ Limited Warranty equipment (excluding intended equipment as specified in this Please note that the scope of warranty for our products is limited to catalog or the individual product specification sheets) which may the delivered our products themselves and TAIYO YUDEN shall not cause loss of human life, bodily injury, serious property damage be in any way responsible for any damages resulting from a failure and/or serious public impact due to a failure or defect of the or defect in our products. Notwithstanding the foregoing, if there is products and/or malfunction attributed thereto. a written agreement (e.g., supply and purchase agreement, quality (1) Transportation equipment (automotive powertrain control assurance agreement) signed by TAIYO YUDEN and your company, system, train control system, and ship control system, etc.) TAIYO YUDEN will warrant our products in accordance with such (2) Traffic signal equipment agreement. (3) Disaster prevention equipment, crime prevention equipment (4) Medical devices classified as GHTF Class C (Japan Class III) ■ TAIYO YUDEN’s Official Sales Channel (5) Highly public information network equipment, data- The contents of this catalog are applicable to our products which are processing equipment (telephone exchange, and base purchased from our sales offices or authorized distributors (hereinafter station, etc.) “TAIYO YUDEN’s official sales channel”). Please note that the contents (6) Any other equipment requiring high levels of quality and/or of this catalog are not applicable to our products purchased from any reliability equal to the equipment listed above seller other than TAIYO YUDEN’s official sales channel. 3. Equipment Prohibited for Use ■ Caution for Export Please do not incorporate our products into the following Some of our products listed in this catalog may require specific equipment requiring extremely high levels of safety and/or procedures for export according to“ U.S. Export Administration reliability. Regulations”,“ Foreign Exchange and Foreign Trade Control Law” (1) Aerospace equipment (artificial satellite, rocket, etc.) of Japan, and other applicable regulations. Should you have any (2) Aviation equipment *1 questions on this matter, please contact our sales staff. (3) Medical devices classified as GHTF Class D (Japan Class IV), implantable medical devices *2 20

for General Electronic Equipment for General Electronic Equipment MULTILAYER CHIP INDUCTORS FOR HIGH FREQUENCY APPLICATIONS(HK SERIES) MULTILAYER CHIP INDUCTORS FOR HIGH FREQUENCY APPLICATIONS（HK SERIES） W AWVAE＊VE* RREEFFLLOOWW *Excep＊t Efxocer pHt fKor0 H6K0036, 0H3,K H1K0100505 ■PARTS NUMBER * Operating Temp.：-55～+125℃（HK1608/2125：-40～+85℃） H K △ 0 6 0 3 △ 1 0 N J － T △＝Blank space ① ② ③ ④ ⑤ ①Series name ③Nominal inductance IN Code Series name Code D Nominal inductance［nH］ U Multilayer chip inductor for high frequency （example） C HK△ T applications 3N9 3.9 O R 10N 10.0 S ②Dimensions（L×W） R10 100 Dimensions R12 120 Code Type（inch） （L×W）［mm］ ※R＝Decimal point IN 0603 0603（0201） 0.6×0.3 ※N＝0.0（nH type） D 1005 1005（0402） 1.0×0.5 U 1608 1608（0603） 1.6×0.8 ④Inductance tolerance C T 2125 2125（0805） 2.0×1.2 Code Inductance tolerance O J ±5％ R S ±0.3nH S F O ⑤Packaging R Code Packaging H －T Taping IG H F ■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY R E Q W U L E N T C Y e A P P L IC A Type L W T e Standard quantity［pcs］ T Paper tape Embossed tape IO HK 0603 0.6±0.03 0.3±0.03 0.3±0.03 0.15±0.05 15000 － N （0201） （0.024±0.001） （0.012±0.001） （0.012±0.001） （0.006±0.002） S HK 1005 1.0±0.05 0.5±0.05 0.5±0.05 0.25±0.10 10000 － （0402） （0.039±0.002） （0.020±0.002） （0.020±0.002） （0.010±0.004） HK 1608 1.6±0.15 0.8±0.15 0.8±0.15 0.3±0.2 4000 － （0603） （0.063±0.006） （0.031±0.006） （0.031±0.006） （0.012±0.008） 2.0＋0.3/－0.1 1.25±0.2 0.85±0.2 0.5±0.3 － 4000 HK 2125 （0.079＋0.012/－0.004） （0.049±0.008） （0.033±0.008） （0.020±0.012） （0805） 2.0＋0.3/－0.1 1.25±0.2 1.0＋0.2/－0.3 0.5±0.3 － 3000 （0.079＋0.012/－0.004） （0.049±0.008） （0.039＋0.008/－0.012） （0.020±0.012） Unit：mm（inch） i_mlci_HK_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 92 20

for General Electronic Equipment ■PARTS NUMBER ●HK 0603 Parts number EHS inNduocmtiannacle Inductance Q LQfr eMqeuaesnucrying Q（Typical）frequency［MHｚ］ freSqeulfe-nrceys o［nManHtｚ］ DC R［eΩsis］tance Rated current Thickness tolerance ※） （min.） ［mA］（max.） ［mm］ ［nH］ ［MHz］ 100 300 500 800 1000 （min.） （typ.） （max.） （typ.） HK 0603 1N0[]-T RoHS 1.0 ±0.3nH 4 100 6 12 17 22 27 10000 > 13000 0.11 0.088 470 0.30±0.03 HK 0603 1N2[]-T RoHS 1.2 ±0.3nH 4 100 6 12 16 21 25 10000 > 13000 0.12 0.089 450 0.30±0.03 HK 0603 1N5[]-T RoHS 1.5 ±0.3nH 4 100 6 12 15 20 23 10000 > 13000 0.13 0.11 430 0.30±0.03 HK 0603 1N8[]-T RoHS 1.8 ±0.3nH 4 100 6 12 15 20 23 10000 > 13000 0.16 0.12 390 0.30±0.03 HK 0603 2N0[]-T RoHS 2.0 ±0.3nH 4 100 6 12 15 20 22 10000 > 13000 0.17 0.13 380 0.30±0.03 HK 0603 2N2[]-T RoHS 2.2 ±0.3nH 4 100 6 12 15 20 22 8800 12500 0.19 0.14 360 0.30±0.03 HK 0603 2N4[]-T RoHS 2.4 ±0.3nH 4 100 6 12 15 20 22 8300 11700 0.20 0.15 350 0.30±0.03 HK 0603 2N7[]-T RoHS 2.7 ±0.3nH 5 100 7 12 15 20 22 7700 11000 0.21 0.16 340 0.30±0.03 HK 0603 3N0[]-T RoHS 3.0 ±0.3nH 5 100 7 12 15 20 22 7200 11000 0.22 0.18 330 0.30±0.03 HK 0603 3N3[]-T RoHS 3.3 ±0.3nH 5 100 7 12 15 20 22 6700 9600 0.23 0.19 320 0.30±0.03 IN HK 0603 3N6[]-T RoHS 3.6 ±0.3nH 5 100 7 12 15 20 22 6400 9100 0.25 0.20 310 0.30±0.03 D HK 0603 3N9[]-T RoHS 3.9 ±0.3nH 5 100 7 12 15 20 22 6000 8600 0.27 0.20 300 0.30±0.03 U HK 0603 4N3[]-T RoHS 4.3 ±0.3nH 5 100 7 12 15 19 21 5700 8100 0.30 0.22 280 0.30±0.03 CT HK 0603 4N7[]-T RoHS 4.7 ±0.3nH 5 100 7 12 15 19 21 5300 7600 0.30 0.24 280 0.30±0.03 O HK 0603 5N1[]-T RoHS 5.1 ±0.3nH 5 100 7 12 15 19 21 5000 7100 0.33 0.26 270 0.30±0.03 RS HK 0603 5N6[]-T RoHS 5.6 ±0.3nH 5 100 7 12 15 19 21 4600 6600 0.36 0.27 260 0.30±0.03 HK 0603 6N2[]-T RoHS 6.2 ±0.3nH 5 100 7 11 14 18 20 4200 6100 0.38 0.29 250 0.30±0.03 HK 0603 6N8[]-T RoHS 6.8 ±5％ 5 100 7 11 14 18 20 3900 5600 0.39 0.30 250 0.30±0.03 HK 0603 7N5[]-T RoHS 7.5 ±5％ 5 100 7 11 14 18 19 3600 5300 0.41 0.34 240 0.30±0.03 IN HK 0603 8N2[]-T RoHS 8.2 ±5％ 5 100 7 11 14 18 19 3400 4900 0.45 0.34 230 0.30±0.03 D HK 0603 9N1[]-T RoHS 9.1 ±5％ 5 100 7 11 14 17 18 3200 4600 0.48 0.40 220 0.30±0.03 U HK 0603 10N[]-T RoHS 10 ±5％ 5 100 7 11 14 17 18 2900 4200 0.51 0.41 220 0.30±0.03 C HK 0603 12N[]-T RoHS 12 ±5％ 5 100 7 11 14 17 18 2700 3800 0.68 0.45 190 0.30±0.03 T HK 0603 15N[]-T RoHS 15 ±5％ 5 100 7 11 13 16 17 2300 3300 0.71 0.50 180 0.30±0.03 O HK 0603 18N[]-T RoHS 18 ±5％ 5 100 7 11 13 16 17 2100 3000 0.81 0.57 170 0.30±0.03 R HK 0603 22N[]-T RoHS 22 ±5％ 5 100 7 11 13 15 16 1800 2600 1.00 0.71 150 0.30±0.03 S HK 0603 27N[]-T RoHS 27 ±5％ 4 100 6 10 12 14 15 1800 2600 1.35 1.11 120 0.30±0.03 F HK 0603 33N[]-T RoHS 33 ±5％ 4 100 6 10 12 14 14 1700 2400 1.47 1.33 110 0.30±0.03 O HK 0603 39N[]-T RoHS 39 ±5％ 4 100 6 10 12 13 12 1500 2100 1.72 1.51 100 0.30±0.03 R HK 0603 47N[]-T RoHS 47 ±5％ 4 100 6 10 11 12 11 1300 1800 1.90 1.74 100 0.30±0.03 H HK 0603 56N[]-T RoHS 56 ±5％ 4 100 6 10 11 11 10 1100 1600 2.27 1.85 80 0.30±0.03 HK 0603 68N[]-T RoHS 68 ±5％ 4 100 6 10 11 11 10 1100 1500 2.66 2.30 80 0.30±0.03 IG HK 0603 82N[]-T RoHS 82 ±5％ 4 100 6 10 11 10 8 1000 1400 3.37 2.60 70 0.30±0.03 H HK 0603 R10[]-T RoHS 100 ±5％ 4 100 6 9 10 9 6 900 1200 3.74 3.00 60 0.30±0.03 F ※ [] mark indicates the Inductance tolerance code. Please refer for the inductance tolerance except the above. R E Q ●HK 1005 Self-resonant DC Resistance Rated current U Nominal Inductance Q LQ Measuring Q（Typical）frequency［MHｚ］ frequency ［MHｚ］ ［Ω］ ［mA］（max.） Thickness E Parts number EHS inductance frequency N ［nH］ tolerance ※） （min.） ［MHz］ 100 300 500 800 1000 （min.） （typ.） （max.） （typ.） -55～ -55～ ［mm］ C +125℃ +85℃ Y HK 1005 1N0[]-T RoHS 1.0 ±0.3nH 8 100 11 25 34 43 52 10000 > 13000 0.08 0.04 300 900 0.50±0.05 HK 1005 1N2[]-T RoHS 1.2 ±0.3nH 8 100 11 25 35 44 52 10000 > 13000 0.09 0.04 300 900 0.50±0.05 A HK 1005 1N5[]-T RoHS 1.5 ±0.3nH 8 100 11 24 33 44 48 6000 > 13000 0.10 0.05 300 850 0.50±0.05 P P HK 1005 1N8[]-T RoHS 1.8 ±0.3nH 8 100 11 23 30 36 42 6000 11000 0.12 0.06 300 700 0.50±0.05 L HK 1005 2N0[]-T RoHS 2.0 ±0.3nH 8 100 11 21 27 34 39 6000 10500 0.12 0.06 300 700 0.50±0.05 IC HK 1005 2N2[]-T RoHS 2.2 ±0.3nH 8 100 10 18 25 31 36 6000 10000 0.13 0.07 300 700 0.50±0.05 A HK 1005 2N4[]-T RoHS 2.4 ±0.3nH 8 100 10 18 24 31 35 6000 9500 0.13 0.07 300 650 0.50±0.05 T HK 1005 2N7[]-T RoHS 2.7 ±0.3nH 8 100 10 18 24 31 34 6000 9000 0.13 0.08 300 650 0.50±0.05 IO HK 1005 3N0[]-T RoHS 3.0 ±0.3nH 8 100 10 18 24 31 35 6000 8500 0.16 0.09 300 600 0.50±0.05 N HK 1005 3N3[]-T RoHS 3.3 ±0.3nH 8 100 10 18 24 31 35 6000 8000 0.16 0.10 300 550 0.50±0.05 S HK 1005 3N6[]-T RoHS 3.6 ±0.3nH 8 100 10 18 24 31 35 5000 7500 0.20 0.11 300 500 0.50±0.05 HK 1005 3N9[]-T RoHS 3.9 ±0.3nH 8 100 10 18 24 31 35 4000 7000 0.21 0.12 300 500 0.50±0.05 HK 1005 4N3[]-T RoHS 4.3 ±0.3nH 8 100 10 18 24 31 35 4000 6500 0.20 0.12 300 500 0.50±0.05 HK 1005 4N7[]-T RoHS 4.7 ±0.3nH 8 100 10 18 24 31 34 4000 6000 0.21 0.12 300 500 0.50±0.05 HK 1005 5N1[]-T RoHS 5.1 ±0.3nH 8 100 10 18 24 31 34 4000 5800 0.21 0.13 300 450 0.50±0.05 HK 1005 5N6[]-T RoHS 5.6 ±0.3nH 8 100 10 18 24 30 35 4000 5700 0.23 0.15 300 430 0.50±0.05 HK 1005 6N2[]-T RoHS 6.2 ±0.3nH 8 100 10 18 24 30 34 3900 5600 0.25 0.16 300 430 0.50±0.05 HK 1005 6N8[]-T RoHS 6.8 ±5％ 8 100 10 18 23 29 32 3900 5500 0.25 0.17 300 430 0.50±0.05 HK 1005 7N5[]-T RoHS 7.5 ±5％ 8 100 10 18 23 29 32 3700 5200 0.25 0.18 300 400 0.50±0.05 HK 1005 8N2[]-T RoHS 8.2 ±5％ 8 100 10 18 23 29 31 3600 4900 0.28 0.21 300 380 0.50±0.05 HK 1005 9N1[]-T RoHS 9.1 ±5％ 8 100 10 18 23 29 31 3400 4500 0.30 0.22 300 360 0.50±0.05 HK 1005 10N[]-T RoHS 10 ±5％ 8 100 10 18 23 29 31 3200 4300 0.31 0.23 300 340 0.50±0.05 HK 1005 12N[]-T RoHS 12 ±5％ 8 100 11 18 23 29 31 2700 3900 0.40 0.28 300 330 0.50±0.05 HK 1005 15N[]-T RoHS 15 ±5％ 8 100 11 18 23 28 30 2300 3500 0.46 0.31 300 320 0.50±0.05 HK 1005 18N[]-T RoHS 18 ±5％ 8 100 11 18 23 28 30 2100 3100 0.55 0.35 300 310 0.50±0.05 HK 1005 22N[]-T RoHS 22 ±5％ 8 100 11 17 22 26 27 1900 2800 0.60 0.42 300 300 0.50±0.05 HK 1005 27N[]-T RoHS 27 ±5％ 8 100 11 17 21 25 26 1600 2300 0.70 0.47 300 300 0.50±0.05 HK 1005 33N[]-T RoHS 33 ±5％ 8 100 11 16 20 23 22 1300 1900 0.80 0.50 200 250 0.50±0.05 HK 1005 39N[]-T RoHS 39 ±5％ 8 100 11 16 20 23 21 1200 1700 0.90 0.52 200 250 0.50±0.05 HK 1005 47N[]-T RoHS 47 ±5％ 8 100 11 16 19 21 18 1000 1500 1.00 0.58 200 230 0.50±0.05 HK 1005 56N[]-T RoHS 56 ±5％ 8 100 11 16 18 18 16 750 1300 1.00 0.61 200 220 0.50±0.05 HK 1005 68N[]-T RoHS 68 ±5％ 8 100 11 15 17 18 11 750 1200 1.20 0.70 180 200 0.50±0.05 HK 1005 82N[]-T RoHS 82 ±5％ 8 100 10 14 16 15 6 600 1100 1.30 0.81 150 200 0.50±0.05 HK 1005 R10[]-T RoHS 100 ±5％ 8 100 10 14 14 12 － 600 1000 1.50 0.94 150 200 0.50±0.05 HK 1005 R12[]-T RoHS 120 ±5％ 8 100 10 12 10 － － 600 800 1.60 1.10 150 200 0.50±0.05 HK 1005 R15[]-T RoHS 150 ±5％ 8 100 12 17 17 － － 550 920 3.20 2.57 140 200 0.50±0.05 HK 1005 R18[]-T RoHS 180 ±5％ 8 100 12 16 － － － 500 810 3.70 2.97 130 200 0.50±0.05 HK 1005 R22[]-T RoHS 220 ±5％ 8 100 12 16 － － － 450 700 4.20 3.29 120 200 0.50±0.05 HK 1005 R27[]-T RoHS 270 ±5％ 8 100 12 14 － － － 400 600 4.80 3.92 110 200 0.50±0.05 ※ [] mark indicates the Inductance tolerance code. Please refer for the inductance tolerance except the above. i_mlci_HK_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 20 93

for General Electronic Equipment ■PARTS NUMBER ●HK 1608 Parts number EHS inNduocmtiannacle Inductance Q LQfr eMqeuaesnucrying Q（Typical）frequency［MHｚ］ freSqeulfe-nrceys o［nManHtｚ］ DC R［eΩsis］tance Rated current Thickness tolerance ※） （min.） ［mA］（max.） ［mm］ ［nH］ ［MHz］ 100 300 500 800 1000 （min.） （typ.） （max.） （typ.） HK 1608 1N0[]-T RoHS 1.0 ±0.3nH 8 100 14 30 40 70 90 10000 > 13000 0.05 0.015 300 0.80±0.15 HK 1608 1N2[]-T RoHS 1.2 ±0.3nH 8 100 14 30 40 70 90 10000 > 13000 0.05 0.015 300 0.80±0.15 HK 1608 1N5[]-T RoHS 1.5 ±0.3nH 8 100 14 26 34 47 50 6000 > 13000 0.10 0.03 300 0.80±0.15 HK 1608 1N8[]-T RoHS 1.8 ±0.3nH 8 100 10 18 24 30 34 6000 > 13000 0.10 0.06 300 0.80±0.15 HK 1608 2N2[]-T RoHS 2.2 ±0.3nH 8 100 12 22 29 37 40 6000 12000 0.10 0.06 300 0.80±0.15 HK 1608 2N7[]-T RoHS 2.7 ±0.3nH 10 100 13 24 32 41 45 6000 11000 0.10 0.06 300 0.80±0.15 HK 1608 3N3[]-T RoHS 3.3 ±0.3nH 10 100 14 25 33 42 47 6000 9000 0.12 0.06 300 0.80±0.15 HK 1608 3N9[]-T RoHS 3.9 ±0.3nH 10 100 13 25 33 42 46 6000 8000 0.14 0.07 300 0.80±0.15 HK 1608 4N7[]-T RoHS 4.7 ±0.3nH 10 100 13 25 33 42 47 4000 6500 0.16 0.08 300 0.80±0.15 IN HK 1608 5N6[]-T RoHS 5.6 ±0.3nH 10 100 14 25 33 42 46 4000 5800 0.18 0.09 300 0.80±0.15 D HK 1608 6N8[]-T RoHS 6.8 ±5％ 10 100 14 25 33 43 47 4000 5600 0.22 0.11 300 0.80±0.15 U HK 1608 8N2[]-T RoHS 8.2 ±5％ 10 100 14 26 34 44 48 3500 5200 0.24 0.13 300 0.80±0.15 CT HK 1608 10N[]-T RoHS 10 ±5％ 12 100 14 26 34 43 47 3400 4600 0.26 0.16 300 0.80±0.15 O HK 1608 12N[]-T RoHS 12 ±5％ 12 100 14 27 35 45 49 2600 4000 0.28 0.17 300 0.80±0.15 RS HK 1608 15N[]-T RoHS 15 ±5％ 12 100 15 28 37 46 51 2300 3400 0.32 0.20 300 0.80±0.15 HK 1608 18N[]-T RoHS 18 ±5％ 12 100 15 27 36 44 48 2000 3000 0.35 0.21 300 0.80±0.15 HK 1608 22N[]-T RoHS 22 ±5％ 12 100 16 28 36 44 47 1600 2900 0.40 0.25 300 0.80±0.15 HK 1608 27N[]-T RoHS 27 ±5％ 12 100 16 29 37 45 46 1400 2200 0.45 0.28 300 0.80±0.15 IN HK 1608 33N[]-T RoHS 33 ±5％ 12 100 17 31 40 46 47 1200 1800 0.55 0.35 300 0.80±0.15 HK 1608 39N[]-T RoHS 39 ±5％ 12 100 18 31 39 44 44 1100 1600 0.60 0.38 300 0.80±0.15 D HK 1608 47N[]-T RoHS 47 ±5％ 12 100 17 28 34 35 34 900 1600 0.70 0.45 300 0.80±0.15 U HK 1608 56N[]-T RoHS 56 ±5％ 12 100 17 28 34 34 31 900 1400 0.75 0.50 300 0.80±0.15 C HK 1608 68N[]-T RoHS 68 ±5％ 12 100 18 29 34 30 22 700 1200 0.85 0.55 300 0.80±0.15 T O HK 1608 82N[]-T RoHS 82 ±5％ 12 100 18 28 33 27 － 600 1100 0.95 0.60 300 0.80±0.15 HK 1608 R10[]-T RoHS 100 ±5％ 12 100 18 27 28 16 － 600 1000 1.00 0.65 300 0.80±0.15 R S HK 1608 R12[]-T RoHS 120 ±5％ 8 50 16 24 23 － － 500 800 1.20 0.68 300 0.80±0.15 HK 1608 R15[]-T RoHS 150 ±5％ 8 50 13 19 16 － － 500 800 1.20 0.73 300 0.80±0.15 F O HK 1608 R18[]-T RoHS 180 ±5％ 8 50 13 18 12 － － 400 700 1.30 0.85 300 0.80±0.15 R HK 1608 R22[]-T RoHS 220 ±5％ 8 50 12 16 － － － 400 600 1.50 0.95 300 0.80±0.15 HK 1608 R27[]-T RoHS 270 ±5％ 8 50 14 15 － － － 400 550 1.90 1.34 150 0.80±0.15 H HK 1608 R33[]-T RoHS 330 ±5％ 8 50 14 － － － － 350 480 2.10 1.53 150 0.80±0.15 IG HK 1608 R39[]-T RoHS 390 ±5％ 8 50 13 － － － － 350 410 2.30 1.72 150 0.80±0.15 H HK 1608 R47[]-T RoHS 470 ±5％ 8 50 13 － － － － 300 360 2.60 2.04 150 0.80±0.15 F ※ [] mark indicates the Inductance tolerance code. Please refer for the inductance tolerance except the above. R E ●HK 2125 Q U Parts number EHS inNduocmtiannacle Inductance Q LQfr eMqeuaesnucrying Q（Typical）frequency［MHｚ］ freSqeulfe-nrceys o［nManHtｚ］ DC R［eΩsis］tance Rated current Thickness E ［nH］ tolerance （min.） ［MHz］ 100 300 500 800 1000 （min.） （typ.） （max.） （typ.） ［mA］（max.） ［mm］ N HK 2125 1N5S-T RoHS 1.5 ±0.3nH 10 100 21 39 57 61 68 4000 > 6000 0.10 0.02 300 0.85±0.2 C HK 2125 1N8S-T RoHS 1.8 ±0.3nH 10 100 18 35 49 55 59 4000 > 6000 0.10 0.02 300 0.85±0.2 Y HK 2125 2N2S-T RoHS 2.2 ±0.3nH 10 100 18 33 46 53 58 4000 > 6000 0.10 0.03 300 0.85±0.2 A HK 2125 2N7S-T RoHS 2.7 ±0.3nH 12 100 19 36 50 56 60 4000 > 6000 0.10 0.03 300 0.85±0.2 P HK 2125 3N3S-T RoHS 3.3 ±0.3nH 12 100 16 29 40 47 51 4000 > 6000 0.13 0.04 300 0.85±0.2 P L HK 2125 3N9S-T RoHS 3.9 ±0.3nH 12 100 18 33 46 54 60 4000 > 6000 0.15 0.05 300 0.85±0.2 IC HK 2125 4N7S-T RoHS 4.7 ±0.3nH 12 100 18 34 46 55 60 3500 > 6000 0.20 0.05 300 0.85±0.2 A HK 2125 5N6S-T RoHS 5.6 ±0.3nH 15 100 20 38 51 60 66 3200 5400 0.23 0.05 300 0.85±0.2 T HK 2125 6N8J-T RoHS 6.8 ±5％ 15 100 20 39 52 63 69 2800 4200 0.25 0.06 300 0.85±0.2 IO HK 2125 8N2J-T RoHS 8.2 ±5％ 15 100 21 40 54 63 70 2400 3700 0.28 0.07 300 0.85±0.2 HK 2125 10NJ-T RoHS 10 ±5％ 15 100 20 38 51 60 67 2100 3100 0.30 0.09 300 0.85±0.2 N HK 2125 12NJ-T RoHS 12 ±5％ 15 100 21 39 52 60 67 1900 3000 0.35 0.10 300 0.85±0.2 S HK 2125 15NJ-T RoHS 15 ±5％ 15 100 22 42 55 63 72 1600 2600 0.40 0.11 300 0.85±0.2 HK 2125 18NJ-T RoHS 18 ±5％ 15 100 24 44 57 63 72 1500 2300 0.45 0.13 300 0.85±0.2 HK 2125 22NJ-T RoHS 22 ±5％ 18 100 23 43 55 60 69 1400 2100 0.50 0.16 300 0.85±0.2 HK 2125 27NJ-T RoHS 27 ±5％ 18 100 23 42 53 58 68 1300 1800 0.55 0.17 300 0.85±0.2 HK 2125 33NJ-T RoHS 33 ±5％ 18 100 24 43 54 55 60 1200 1700 0.60 0.19 300 0.85±0.2 HK 2125 39NJ-T RoHS 39 ±5％ 18 100 23 41 50 47 47 1000 1400 0.65 0.25 300 0.85±0.2 HK 2125 47NJ-T RoHS 47 ±5％ 18 100 23 41 49 43 41 900 1200 0.70 0.26 300 1.00＋0.2/－0.3 HK 2125 56NJ-T RoHS 56 ±5％ 18 100 23 42 48 39 38 800 1100 0.75 0.28 300 1.00＋0.2/－0.3 HK 2125 68NJ-T RoHS 68 ±5％ 18 100 25 42 45 30 － 700 900 0.80 0.33 300 1.00＋0.2/－0.3 HK 2125 82NJ-T RoHS 82 ±5％ 18 100 24 41 41 － － 600 800 0.90 0.37 300 1.00＋0.2/－0.3 HK 2125 R10J-T RoHS 100 ±5％ 18 100 23 37 37 － － 600 800 0.90 0.40 300 1.00＋0.2/－0.3 HK 2125 R12J-T RoHS 120 ±5％ 13 50 22 33 29 － － 500 700 0.95 0.43 300 1.00＋0.2/－0.3 HK 2125 R15J-T RoHS 150 ±5％ 13 50 22 34 26 － － 500 700 1.00 0.46 300 1.00＋0.2/－0.3 HK 2125 R18J-T RoHS 180 ±5％ 13 50 23 34 20 － － 400 600 1.10 0.50 300 1.00＋0.2/－0.3 HK 2125 R22J-T RoHS 220 ±5％ 12 50 20 23 － － － 350 550 1.20 0.75 300 1.00＋0.2/－0.3 HK 2125 R27J-T RoHS 270 ±5％ 12 50 20 29 － － － 300 480 1.30 0.85 300 1.00＋0.2/－0.3 HK 2125 R33J-T RoHS 330 ±5％ 12 50 22 15 － － － 250 400 1.40 0.90 300 1.00＋0.2/－0.3 HK 2125 R39J-T RoHS 390 ±5％ 10 50 17 12 － － － 250 400 1.30 0.85 300 1.00＋0.2/－0.3 HK 2125 R47J-T RoHS 470 ±5％ 10 50 17 － － － － 200 350 1.50 0.95 300 1.00＋0.2/－0.3 ※ [] mark indicates the Inductance tolerance code. Please refer for the inductance tolerance except the above. i_mlci_HK_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 94 20

Multilayer chip inductors Multilayer chip inductors for high frequency, Multilayer chip bead inductors Multilayer common mode choke coils（MC series F type） Metal Multilayer Chip Power Inductors (MCOILTM MC series) ■PACKAGING ①Minimum Quantity ●Tape & Reel Packaging Thickness Standard Quantity ［pcs］ Type mm（inch） Paper Tape Embossed Tape CK1608（0603） 0.8 （0.031） 4000 － 0.85（0.033） 4000 － CK2125（0805） 1.25（0.049） － 2000 0.85（0.033） 4000 － CKS2125（0805） 1.25（0.049） － 2000 CKP1608（0603） 0.8 （0.031） 4000 － CKP2012（0805） 0.9 （0.035） － 3000 CKP2016（0806） 0.9 （0.035） － 3000 0.7 （0.028） － 3000 CKP2520（1008） 0.9 （0.035） － 3000 1.1 （0.043） － 2000 LK1005（0402） 0.5 （0.020） 10000 － LK1608（0603） 0.8 （0.031） 4000 － 0.85（0.033） 4000 － LK2125（0805） 1.25（0.049） － 2000 HK0603（0201） 0.3 （0.012） 15000 － HK1005（0402） 0.5 （0.020） 10000 － HK1608（0603） 0.8 （0.031） 4000 － 0.85（0.033） － 4000 HK2125（0805） 1.0 （0.039） － 3000 HKQ0603S（0201） 0.3 （0.012） 15000 － HKQ0603U（0201） 0.3 （0.012） 15000 － AQ105（0402） 0.5 （0.020） 10000 － BK0603（0201） 0.3 （0.012） 15000 － BK1005（0402） 0.5 （0.020） 10000 － BKH0603（0201） 0.3 （0.012） 15000 － BKH1005（0402） 0.5 （0.020） 10000 － BK1608（0603） 0.8 （0.031） 4000 － 0.85（0.033） 4000 － BK2125（0805） 1.25（0.049） － 2000 BK2010（0804） 0.45（0.018） 4000 － BK3216（1206） 0.8 （0.031） － 4000 BKP0603（0201） 0.3 （0.012） 15000 － BKP1005（0402） 0.5 （0.020） 10000 － BKP1608（0603） 0.8 （0.031） 4000 － BKP2125（0805） 0.85（0.033） 4000 － MCF0605（0202） 0.3 （0.012） 15000 － MCF0806（0302） 0.4 （0.016） － 10000 MCF1210（0504） 0.55（0.022） － 5000 MCF2010（0804） 0.45（0.018） － 4000 MCEE1005（0402） 0.55（0.022） 10000 － MCEK1210(0504) 0.5 （0.020） 5000 － MCFK1608（0603） 0.6 （0.024） 4000 － MCFE1608（0603） 0.65（0.026） 4000 － MCHK1608(0603) 0.8 （0.031） 4000 － MCKK1608（0603） 1.0 （0.039） 3000 MCHK2012（0806） 0.8 （0.031） 4000 － MCKK2012（0805） 1.0 （0.039） - 3000 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E08R01

②Taping material ●Card board carrier tape Top tape CK 1608 BK 0603 CKP 1608 BK 1005 CK 2125 BK 1608 CKS 2125 BK 2125 LK 1005 BK 2010 LK 1608 BKP 0603 Base tape LK 2125 BKP 1005 HK 0603 BKP 1608 HK 1005 BKP 2125 Sprocket hole HK 1608 BKH 0603 HKQ 0603 BKH 1005 AQ 105 MCF 0605 Bottom tape Chip cavity MC 1005 MC 1210 MC 1608 Chip Filled MC 2012 Chip ●Embossed Tape Top tape CK 2125 BK 2125 CKS 2125 BK 3216 CKP 2012 MCF 0806 CKP 2016 MCF 1210 CKP 2520 MCF 2010 LK 2125 MC 1608 HK 2125 MC 2012 Sprocket hole Base tape Chip cavity Chip Filled Chip ③Taping Dimensions ●Paper tape (8mm wide) Unit：mm（inch） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） T A B 3.5±0.05(0.138±0.002) 8.0±0.30.315±0.012) ( F 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E08R01

Thickness Chip cavity Insertion Pitch Tape Thickness Type mm（inch） Ａ Ｂ Ｆ Ｔ 1.0±0.2 1.8±0.2 4.0±0.1 1.1max CK1608（0603） 0.8 （0.031） （0.039±0.008） （0.071±0.008） （0.157±0.004） （0.043max） 1.5±0.2 2.3±0.2 4.0±0.1 1.1max CK2125（0805） 0.85（0.033） （0.059±0.008） （0.091±0.008） （0.157±0.004） （0.043max） 1.5±0.2 2.3±0.2 4.0±0.1 1.1max CKS2125（0805） 0.85（0.033） （0.059±0.008） （0.091±0.008） （0.157±0.004） （0.043max） 1.0±0.2 1.8±0.2 4.0±0.1 1.1max CKP1608（0603） 0.8 （0.031） （0.039±0.008） （0.071±0.008） （0.157±0.004） （0.043max） 0.65±0.1 1.15±0.1 2.0±0.05 0.8max LK1005（0402） 0.5 （0.020） （0.026±0.004） （0.045±0.004） （0.079±0.002） （0.031max） 1.0±0.2 1.8±0.2 4.0±0.1 1.1max LK1608（0603） 0.8 （0.031） （0.039±0.008） （0.071±0.008） （0.157±0.004） （0.043max） 1.5±0.2 2.3±0.2 4.0±0.1 1.1max LK2125（0805） 0.85（0.033） （0.059±0.008） （0.091±0.008） （0.157±0.004） （0.043max） 0.40±0.06 0.70±0.06 2.0±0.05 0.45max HK0603（0201） 0.3 （0.012） （0.016±0.002） （0.028±0.002） （0.079±0.002） （0.018max） 0.65±0.1 1.15±0.1 2.0±0.05 0.8max HK1005（0402） 0.5 （0.020） （0.026±0.004） （0.045±0.004） （0.079±0.002） （0.031max） 1.0±0.2 1.8±0.2 4.0±0.1 1.1max HK1608（0603） 0.8 （0.031） （0.039±0.008） （0.071±0.008） （0.157±0.004） （0.043max） 0.40±0.06 0.70±0.06 2.0±0.05 0.45max HKQ0603S（0201） 0.3 （0.012） （0.016±0.002） （0.028±0.002） （0.079±0.002） （0.018max） 0.40±0.06 0.70±0.06 2.0±0.05 0.45max HKQ0603U（0201） 0.3 （0.012） （0.016±0.002） （0.028±0.002） （0.079±0.002） （0.018max） 0.75±0.1 1.15±0.1 2.0±0.05 0.8max AQ105（0402） 0.5 （0.020） （0.030±0.004） （0.045±0.004） （0.079±0.002） （0.031max） 0.40±0.06 0.70±0.06 2.0±0.05 0.45max BK0603（0201） 0.3 （0.012） （0.016±0.002） （0.028±0.002） （0.079±0.002） （0.018max） 0.65±0.1 1.15±0.1 2.0±0.05 0.8max BK1005（0402） 0.5 （0.020） （0.026±0.004） （0.045±0.004） （0.079±0.002） （0.031max） 1.0±0.2 1.8±0.2 4.0±0.1 1.1max BK1608（0603） 0.8 （0.031） （0.039±0.008） （0.071±0.008） （0.157±0.004） （0.043max） 1.5±0.2 2.3±0.2 4.0±0.1 1.1max BK2125（0805） 0.85（0.033） （0.059±0.008） （0.091±0.008） （0.157±0.004） （0.043max） 1.2±0.1 2.17±0.1 4.0±0.1 0.8max BK2010（0804） 0.45（0.018） （0.047±0.004） （0.085±0.004） （0.157±0.004） （0.031max） 0.40±0.06 0.70±0.06 2.0±0.05 0.45max BKP0603（0201） 0.3 （0.012） （0.016±0.002） （0.028±0.002） （0.079±0.002） （0.018max） 0.65±0.1 1.15±0.1 2.0±0.05 0.8max BKP1005（0402） 0.5 （0.020） （0.026±0.004） （0.045±0.004） （0.079±0.002） （0.031max） 1.0±0.2 1.8±0.2 4.0±0.1 1.1max BKP1608（0603） 0.8 （0.031） （0.039±0.008） （0.071±0.008） （0.157±0.004） （0.043max） 1.5±0.2 2.3±0.2 4.0±0.1 1.1max BKP2125（0805） 0.85（0.033） （0.059±0.008） （0.091±0.008） （0.157±0.004） （0.043max） 0.40±0.06 0.70±0.06 2.0±0.05 0.45max BKH0603（0201） 0.3 （0.012） （0.016±0.002） （0.028±0.002） （0.079±0.002） （0.018max） 0.65±0.1 1.15±0.1 2.0±0.05 0.8max BKH1005（0402） 0.5 （0.020） （0.026±0.004） （0.045±0.004） （0.079±0.002） （0.031max） 0.62±0.03 0.77±0.03 2.0±0.05 0.45max MCF0605（0202） 0.3 （0.012） （0.024±0.001） （0.030±0.001） （0.079±0.002） （0.018max） 1.1±0.05 1.9±0.05 4.0±0.1 0.72max MCFK1608（0603） 0.6 （0.024） （0.043±0.002） （0.075±0.002） （0.157±0.004） (0.028max) 0.8±0.05 1.3±0.05 2.0±0.05 0.64max MCEE1005（0402） 0.55（0.021） (0.031±0.002) (0.051±0.002) （0.079±0.002） (0.025max) 1.3±0.1 1.55±0.1 4.0±0.1 0.64max MCEK1210（0504） 0.5 （0.020） （0.051±0.004） （0.061±0.004） （0.157±0.004） (0.025max) 1.1±0.05 1.9±0.05 4.0±0.1 0.72max MCFK1608（0603） 0.6 （0.024） （0.043±0.002） （0.075±0.002） （0.157±0.004） (0.028max) 1.1±0.05 1.9±0.05 4.0±0.1 0.72max MCFE1608（0603） 0.65（0.026） （0.043±0.002） （0.075±0.002） （0.157±0.004） (0.028max) 1.2±0.05 2.0±0.05 4.0±0.1 0.9max MCHK1608（0603） 0.8 （0.031） （0.047±0.002） （0.079±0.002） （0.157±0.004） (0.035max) 1.65±0.1 2.4±0.1 4.0±0.1 0.9max MCHK2012（0805） 0.8 （0.031） （0.065±0.004） （0.094±0.004） （0.157±0.004） （0.035max） Unit : mm（inch） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E08R01

●Embossed Tape (8mm wide) Unit：mm（inch） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） A B 3.5±0.05(0.138±0.002) 8.0±0.30.315±0.012) ( F 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) Thickness Chip cavity Insertion Pitch Tape Thickness Type mm（inch） Ａ Ｂ Ｆ K T 1.5±0.2 2.3±0.2 4.0±0.1 2.0 0.3 CK2125（0805） 1.25（0.049） （0.059±0.008） （0.091±0.008） （0.157±0.004） （0.079） （0.012） 1.5±0.2 2.3±0.2 4.0±0.1 2.0 0.3 CKS2125（0805） 1.25（0.049） （0.059±0.008） （0.091±0.008） （0.157±0.004） （0.079） （0.012） 1.55±0.2 2.3±0.2 4.0±0.1 1.3 0.3 CKP2012（0805） 0.9 （0.035） （0.061±0.008） （0.091±0.008） （0.157±0.004） （0.051） （0.012） 1.8±0.1 2.2±0.1 4.0±0.1 1.3 0.25 CKP2016（0806） 0.9 （0.035） （0.071±0.004） （0.087±0.004） （0.157±0.004） （0.051） （0.01） 1.4 0.7 （0.028） （0.055） 1.4 0.9 （0.035） 2.3±0.1 2.8±0.1 4.0±0.1 （0.055） 0.3 CKP2520（1008） （0.091±0.004） （0.110±0.004） （0.157±0.004） 1.7 （0.012） 1.1 （0.043） （0.067） 1.7 1.1 （0.043） （0.067） 1.5±0.2 2.3±0.2 4.0±0.1 2.0 0.3 LK2125（0805） 1.25（0.049） （0.059±0.008） （0.091±0.008） （0.157±0.004） （0.079） （0.012） 1.5 0.85（0.033） 1.5±0.2 2.3±0.2 4.0±0.1 （0.059） 0.3 HK2125（0805） （0.059±0.008） （0.091±0.008） （0.157±0.004） 2.0 （0.012） 1.0 （0.039） （0.079） 1.5±0.2 2.3±0.2 4.0±0.1 2.0 0.3 BK2125（0805） 1.25（0.049） （0.059±0.008） （0.091±0.008） （0.157±0.004） （0.079） （0.012） 1.9±0.1 3.5±0.1 4.0±0.1 1.4 0.3 BK3216（1206） 0.8 （0.031） （0.075±0.004） （0.138±0.004） （0.157±0.004） （0.055） （0.012） 0.75±0.05 0.95±0.05 2.0±0.05 0.55 0.3 MCF0806（0302） 0.4 （0.016） （0.030±0.002） （0.037±0.002） （0.079±0.002） （0.022） （0.012） 1.15±0.05 1.40±0.05 4.0±0.1 0.65 0.3 MCF1210（0504） 0.55（0.022） （0.045±0.002） （0.055±0.002） （0.157±0.004） （0.026） （0.012） 1.1±0.1 2.3±0.1 4.0±0.1 0.85 0.3 MCF2010（0804） 0.45（0.018） （0.043±0.004） （0.091±0.004） （0.157±0.004） （0.033） （0.012） 1.1±0.1 1.95±0.1 4.0±0.1 1.4 0.25 MCKK1608（0603） 1.0 （0.039） （0.043±0.004） （±0.004） （0.157±0.004） （0.055） （0.01） 1.55±0.1 2.35±0.1 4.0±0.1 1.35 0.25 MCKK2012（0805） 1.0 （0.039） （0.061±0.004） （0.093±0.004） （0.157±0.004） （0.053） （0.010） Unit : mm（inch） ④LEADER AND BLANK PORTION Blank portion Chip cavity Blank portion Leader 160mm or more 100mm or more (6.3inches or more) (3.94inches or more) 400mm or more Direction of tape feed (15.7inches or more) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E08R01

⑤Reel Size t E C B A R D W A B C D E R φ178±2.0 φ50 or more φ13.0±0.2 φ21.0±0.8 2.0±0.5 1.0 t W 4mm width tape 1.5max. 5±1.0 8mm width tape 2.5max. 10±1.5 (Unit : mm) ⑥Top tape strength The top tape requires a peel-off force of 0.1～0.7N in the direction of the arrow as illustrated below. Pull direction 0～15° Top tape Base tape ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E08R01

Multilayer chip inductors Multilayer chip inductors for high frequency, Multilayer chip bead inductors Multilayer common mode choke coils（MC series F type） Metal Multilayer Chip Power Inductors (MCOILTM MC series) ■RELIABILITY DATA 1. Operating Temperature Range BK series －55～＋125℃ BKH series BKP series －55～＋85℃ MCF series －40～＋85℃ CK series CKS series －40～＋85℃ Specified Value CKP series LK series HK0603, HK1005 －55～＋125℃ HK1608, HK2125 －40～＋85℃ HKQ0603 －55～＋125℃ AQ105 MCOILTM MC series －40～＋125℃（Including self-generated heat） 2. Storage Temperature Range BK series －55～＋125℃ BKH series BKP series －55～＋85℃ MCF series －40～＋85℃ CK series CKS series －40～＋85℃ Specified Value CKP series LK series HK0603, HK1005 －55～＋125℃ HK1608, HK2125 －40～＋85℃ HKQ0603 －55～＋125℃ AQ105 MCOILTM MC series －40～＋85℃ 3. Rated Current BK series The temperature of the element is increased within 20℃. BKH series BKP series The temperature of the element is increased within 40℃ MCF series Refer to each specification. CK series The temperature of the element is increased within 20℃. CKS series CKP series The temperature of the element is increased within 40℃ Specified Value LK series The decreasing-rate of inductance value is within 5 % HK0603, HK1005 HK1608, HK2125 The decreasing-rate of inductance value is within 5 %, or the temperature of the element is HKQ0603 increased within 20℃ AQ105 Idc1: The decreasing-rate of inductance value is within 30 % MCOILTM MC series Idc2: The temperature of the element is increased within 40℃ ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E08R01

4. Impedance BK series BKH series Specified Value Refer to each specification. BKP series MCF series BK0603Series, BKP0603Series, BKH Series Measuring frequency : 100±1MHz Measuring equipment : 4991A（or its equivalent） Measuring jig : 16193A（or its equivalent） BK1005Series, BKP1005Series ,BKH1005Series Measuring frequency : 100±1MHz Measuring equipment : 4291A（or its equivalent） Measuring jig : 16192A（or its equivalent）, HW:16193A（or its equivalent） Test Methods and BK1608・2125Series, BKP1608・2125Series Remarks Measuring frequency : 100±1MHz Measuring equipment : 4291A（or its equivalent）, 4195A（or its equivalent） Measuring jig : 16192A（or its equivalent）, HW:16193A（or its equivalent） BK2010・3216Series Measuring frequency : 100±1MHz Measuring equipment : 4291A（or its equivalent）, 4195A（or its equivalent） Measuring jig : 16192A（or its equivalent） MCF Series Measuring frequency : 100±1MHz Measuring equipment : 4291A（or its equivalent） 5. Inductance CK series CKS series CKP series LK series Specified Value HK0603, HK1005 Refer to each specification. HK1608, HK2125 HKQ0603 AQ105 MCOILTM MC series CK、CKS、LK Series Measuring frequency : Refer to each specification. Measuring equipment /jig : 1608,2125⇒4294A＋16092A（or its equivalent） 1005⇒4291A＋16193A（or its equivalent） Measuring current : 047～4.7μH ⇒1mArms 、 5.6～33μH ⇒0.1mArms CKP、MCOILTM MC Series Measuring frequency : 1MHz Measuring equipment : 4285A（or its equivalent） Test Methods and HK0603、HK1005、AQ Series Remarks Measuring frequency : 100MHz Measuring equipment /jig : HK0603⇒ E4991A+16197A（or its equivalent） , AQ105⇒4291A＋16197A（or its equivalent） HK1005⇒ 4291A＋16193A（or its equivalent） HK1608、HK2125 Series Measuring frequency : ～100nH⇒100MHz 、120nH～⇒50MHz Measuring equipment /jig : 4291A＋16092A（or its equivalent） HKQ Series Measuring frequency : 500MHz Measuring equipment /jig : E4991A＋16197A（or its equivalent） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E08R01

6. Q CK series CKS series － CKP series LK series Specified Value HK0603, HK1005 HK1608, HK2125 Refer to each specification. HKQ0603 AQ105 MCOILTM MC series － LK Series Measuring frequency : Refer to each specification. Measuring equipment /jig : 1608,2125⇒4294A＋16092A（or its equivalent） 1005⇒4291A＋16193A（or its equivalent） Measuring current : 047～4.7μH ⇒1mArms 、 5.6～33μH ⇒0.1mArms HK0603、HK1005、AQ Series Test Methods and Measuring frequency : 100MHz Remarks Measuring equipment /jig : HK0603⇒E4991A＋16197A（or its equivalent） , AQ105⇒4291A＋16197A（or its equivalent） HK1005⇒4291A＋16193A（or its equivalent） HK1608、HK2125 Series Measuring frequency : ～100nH⇒100MHz 、120nH～⇒50MHz Measuring equipment /jig : 4291A＋16092A（or its equivalent） HKQ Series Measuring frequency : 500MHz Measuring equipment /jig : E4991A＋16197A（or its equivalent） 7. DC Resistance BK series BKH series BKP series MCF series CK series CKS series Specified Value CKP series Refer to each specification. LK series HK0603, HK1005 HK1608, HK2125 HKQ0603 AQ105 MCOILTM MC series Test Methods and Measuring equipment：IWATSU VOAC7512, HIOKI RM3545 (or its equivalent) Remarks 8. Self Resonance Frequency（SRF） BK series BKH series － BKP series MCF series CK series Refer to each specification. CKS series Specified Value CKP series － LK series HK0603, HK1005 HK1608, HK2125 Refer to each specification. HKQ0603 AQ105 MCOILTM MC series － LK、CK Series : Measuring equipment : 4195A（or its equivalent） Test Methods and Measuring jig : 16092A（or its equivalent） Remarks HK、HKQ、AQ Series : Measuring equipment : 8719C（or its equivalent） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E08R01

9. Resistance to Flexure of Substrate BK series BKH series BKP series MCF series CK series CKS series Specified Value CKP series No mechanical damage. LK series HK0603, HK1005 HK1608, HK2125 HKQ0603 AQ105 MCOILTM MC series Warp : 2mm（BK Series、BKP、BKH1005、CK、CKS、CKP、LK、HK、HKQ0603S、HKQ0603U、AQ Series、MCF1210、MC Series） : 1mm（BKH0603、MCF Series without 1210 size,） Testing board : glass epoxy-resin substrate Thickness : 0.8mm 20 Test Methods and Remarks R-230 Board Warp Deviation±1 45 45 （Unit：mm） 10. Solderability BK series BKH series BKP series MCF series CK series CKS series Specified Value CKP series At least 90％ of terminal electrode is covered by new solder. LK series HK0603, HK1005 HK1608, HK2125 HKQ0603 AQ105 MCOILTM MC series Solder temperature ：230±5℃ (JIS Z 3282 H60A or H63A) Test Methods and Solder temperature ：245±3℃ (Sn/3.0Ag/0.5Cu) Remarks Duration ：4±1 sec. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E08R01

11. Resistance to Soldering BK series Appearance：No significant abnormality BKH series Impedance change：Within ±30％ BKP series Appearance：No significant abnormality MCF series Impedance change：Within ±20％ Appearance：No significant abnormality CK series Inductance change： R10～4R7⇒Within ±10％、 6R8～100⇒Within ±15％ Appearance：No significant abnormality CKS series Inductance change：Within ±20％ Appearance：No significant abnormality Specified Value CKP series Inductance change：Within ±30％ Appearance：No significant abnormality LK series Inductance change：1005⇒Within ±15％ 1608,2125⇒ 47N～4R7: Within ±10％ 5R6～330: Within ±15％ HK0603, HK1005 HK1608, HK2125 Appearance：No significant abnormality HKQ0603 Inductance change： Within ±5％ AQ105 Appearance：No significant abnormality MCOILTM MC series Inductance change： Within ±10％ Solder temperature ：260±5℃ Duration ：10±0.5 sec. Test Methods and Preheating temperature ：150 to 180℃ Remarks Preheating time ：3 min. Flux ：Immersion into methanol solution with colophony for 3 to 5 sec. Recovery ：2 to 3 hrs of recovery under the standard condition after the test.（See Note 1） (Note 1) When there a re questions concerning measurement result；measurement shall be made after 48±2 hrs of recovery under the standard condition. 12. Thermal Shock BK series Appearance：No significant abnormality BKH series Impedance change： Within ±30％ BKP series Appearance：No significant abnormality MCF series Impedance change： Within ±20％ CK series Appearance：No significant abnormality CKS series Inductance change：Within ±20％ Appearance：No significant abnormality CKP series Specified Value Inductance change： Within ±30％ Appearance：No significant abnormality LK series Inductance change： Within ±10％ Q change： Within ±30％ HK0603, HK1005 HK1608, HK2125 Appearance：No significant abnormality HKQ0603 Inductance change： Within ±10％ Q change： Within ±20％ AQ105 Appearance：No significant abnormality MCOILTM MC series Inductance change： Within ±10％ Conditions for 1 cycle Step temperature（℃） time（min.） 1 Minimum operating temperature ＋0/－3 30±3 Test Methods and 2 Room temperature 2～3 Remarks 3 Maximum operating temperature ＋3/－0 30±3 4 Room temperature 2～3 Number of cycles：5 Recovery：2 to 3 hrs of recovery under the standard condition after the test.（See Note 1） (Note 1) When there are questions concerning measurement result；measurement shall be made after 48±2 hrs of recovery under the standard condition. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E08R01

13. Damp Heat（ Steady state） BK series Appearance：No significant abnormality BKH series Impedance change： Within ±30％ BKP series Appearance：No significant abnormality MCF series Impedance change： Within ±20％ CK series Appearance：No significant abnormality CKS series Inductance change： Within ±20％ Appearance：No significant abnormality CKP series Inductance change： Within ±30％ Specified Value Appearance：No significant abnormality LK series Inductance change： 1005,1608⇒Within ±10％ 2125⇒Within ±20％ Q change： Within ±30％ HK0603, HK1005 HK1608, HK2125 Appearance：No significant abnormality HKQ0603 Inductance change： Within ±10％ Q change： Within ±20％ AQ105 Appearance：No significant abnormality MCOILTM MC series Inductance change： Within ±10％ BK、BKP、BKH、LK、CK、CKS、CKP、MCF Series： Temperature ：40±2℃ Humidity ：90 to 95％RH Duration ：500 +24/-0 hrs Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1） Test Methods and Remarks HK、HKQ、AQ、MCOILTM MC series： Temperature ：60±2℃ Humidity ：90 to 95％RH Duration ：500 +24/-0 hrs Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1） (Note 1) When there are questions concerning measurement result；measurement shall be made after 48±2 hrs of recovery under the standard condition. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E08R01

14. Loading under Damp Heat BK series Appearance：No significant abnormality BKH series Impedance change： Within ±30％ BKP series MCF series － CK series Appearance：No significant abnormality CKS series Inductance change： Within ±20％ Appearance：No significant abnormality CKP series Inductance change： Within ±30％ Appearance：No significant abnormality Inductance change： 1005⇒Within ±10％ Specified Value 1608⇒0.047～12.0μH： Within ±10％ 15.0～33.0μH： Within ± LK series 15％ 2125⇒Within ±20％ Q change： Within ±30％ HK0603, HK1005 HK1608, HK2125 Appearance：No significant abnormality HKQ0603 Inductance change： Within ±10％ Q change： Within ±20％ AQ105 Appearance：No significant abnormality MCOILTM MC series※ Inductance change： Within ±10％ BK、BKP、BKH、LK、CK、CKS、CKP Series： Temperature ：40±2℃ Humidity ：90 to 95％RH Applied current ：Rated current Duration ：500 +24/-0 hrs Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1） Test Methods and Remarks HK、HKQ、AQ、MCOILTM MC Series： Temperature ：60±2℃ Humidity ：90 to 95％RH Applied current ：Rated current ※MC series ; Idc2max Duration ：500 +24/-0 hrs Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1） Note on standard con dition: "standard condition" referred to herein is defined as follows: 5 to 35℃ of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure. When there are questions concerning measurement results: In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure. Unless otherwise specified, all the tests are conducted under the "standard condition." (Note 1) Measurement shall be made after 48±2 hrs of recovery under the standard condition. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E08R01

15. Loading at High Temperature BK series Appearance：No significant abnormality BKH series Impedance change： Within ±30％ BKP series Appearance：No significant abnormality MCF series Impedance change： Within ±20％ CK series Appearance：No significant abnormality CKS series Inductance change： Within ±20％ Appearance：No significant abnormality CKP series Inductance change： Within ±30％ Appearance：No significant abnormality Specified Value Inductance change： 1005⇒Within ±10％ 1608⇒0.047～12.0μH： Within ±10％ 15.0～33.0μH： Within ± LK series 15％ 2125⇒Within ±20％ Q change： Within ±30％ HK0603, HK1005 HK1608, HK2125 Appearance：No significant abnormality HKQ0603 Inductance change： Within ±10％ Q change： Within ±20％ AQ105 Appearance：No significant abnormality MCOILTM MC series※ Inductance change： Within ±10％ Temperature : Maximum operating temperature Test Methods and Applied current ：Rated current ※MC series ; Idc2max Remarks Duration ：500 +24/-0 hrs Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber. （See Note 1） Note on standard condition: "standard condition" referred to herein is defined as follows: 5 to 35℃ of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure. When there are questions concerning measurement results: In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure. Unless otherwise specified, all the tests are conducted under the "standard condition." (Note 1) Measurement shall be made after 48±2 hrs of recovery under the standard condition. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E08R01

Precautions on the use of Multilayer chip inductors Multilayer chip inductors for high frequency, Multilayer chip bead inductors Multilayer common mode choke coils（MC series F type） ■PRECAUTIONS 1. Circuit Design ◆Verification of operating environment, electrical rating and performance 1. A malfunction in medical equipment, spacecraft, nuclear reactors, etc. may cause serious harm to human life or have severe social ramifications. As such, any inductors to be used in such equipment may require higher safety and/or reliability considerations and should be clearly Precautions differentiated from components used in general purpose applications. ◆Operating Current（Verification of Rated current） 1. The operating current including inrush current for inductors must always be lower than their rated values. 2. Do not apply current in excess of the rated value because the inductance may be reduced due to the magnetic saturation effect. 2. PCB Design ◆Pattern configurations（Design of Land-patterns） 1. When inductors are mounted on a PCB, the size of land patterns and the amount of solder used（size of fillet）can directly affect inductor performance. Therefore, the following items must be carefully considered in the design of solder land patterns: （1） The amount of solder applied can affect the ability of chips to withstand mechanical stresses which may lead to breaking or cracking. Therefore, when designing land-patterns it is necessary to consider the appropriate size and configuration of the solder pads which in turn determines the amount of solder necessary to form the fillets. （2） When more than one part is jointly soldered onto the same land or pad, the pad must be designed so that each component's Precautions soldering point is separated by solder-resist. （3） The larger size of land patterns and amount of solder, the smaller Q value after mounting on PCB. It makes higher the Q value to design land patterns smaller than terminal electrode of chips. ◆Pattern configurations（Inductor layout on panelized［ breakaway］ PC boards） 1. After inductors have been mounted on the boards, chips can be subjected to mechanical stresses in subsequent manufacturing processes （PCB cutting, board inspection, mounting of additional parts, assembly into the chassis, wave soldering the reflow soldered boards etc.）For this reason, planning pattern configurations and the position of SMD inductors should be carefully performed to minimize stress. ◆Pattern configurations（Design of Land-patterns） 1. The following diagrams and tables show some examples of recommended patterns to prevent excessive solder amounts（larger fillets which extend above the component end terminations）. Examples of improper pattern designs are also shown. （1） Recommended land dimensions for a typical chip inductor land patterns for PCBs Land pattern ●Recommended land dimensions for Multilayer inductor Chip inductor Solder-resist Wave-soldering （Unit：mm） Type 1608 2012 2125 2016 2520 3216 C L 1.6 2.0 2.0 2.0 2.5 3.2 Size W 0.8 1.25 1.25 1.6 2.0 1.6 B A B A 0.8～1.0 1.0～1.4 1.0～1.4 1.0～1.4 1.0～1.4 1.8～2.5 B 0.5～0.8 0.8～1.5 0.8～1.5 0.8～1.5 0.6～1.0 0.8～1.7 Chip inductor C 0.6～0.8 0.9～1.2 0.9～1.2 1.3～1.6 1.6～2.0 1.2～1.6 W Reflow-soldering （Unit：mm） L Technical Type 0603 1005 105 1608 2012 2125 2016 2520 3216 considerations L 0.6 1.0 1.0 1.6 2.0 2.0 2.0 2.5 3.2 Size W 0.3 0.5 0.6 0.8 1.25 1.25 1.6 2.0 1.6 A 0.20～0.30 0.45～0.55 0.50～0.55 0.8～1.0 0.8～1.2 0.8～1.2 0.8～1.2 1.0～1.4 1.8～2.5 B 0.20～0.30 0.40～0.50 0.30～0.40 0.6～0.8 0.8～1.2 0.8～1.2 0.8～1.2 0.6～1.0 0.6～1.5 C 0.25～0.40 0.45～0.55 0.60～0.70 0.6～0.8 0.9～1.6 0.9～1.6 1.2～2.0 1.8～2.2 1.2～2.0 ●Recommended land dimension for Array type c d (Unit：mm） Type 2010 3216 L 2.0 3.2 a Size W 1.0 1.6 b W a 0.5～0.6 0.7～0.9 b 0.5～0.6 0.8～1.0 a c 0.2～0.3 0.4～0.5 d 0.5 0.8 L ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E08R01

●Recommended land dimension for Multilayer common mode choke coil （Unit：mm） （Unit：mm） c c Type 0605 0806 Type 1210 Size WL 00..6550 00..8655 a a Size WL 11.2.05 a a 0.27～0.30 0.25～0.35 b d W a 0.45～0.55 b d W b 0.17～0.20 0.25～0.35 b 0.7～0.8 c 0.20～0.26 0.25～0.35 a c 0.25～0.35 d 0.4 0.5 L d 0.55 a L （2） Examples of good and bad solder application Item Not recommended Recommended Lead wire of component Solder-resist Mixed mounting of SMD and leaded components Chassis Solder (for grounding) Solder-resist Component placement close to the chassis Electrode pattern Lead wire of component Soldering iron Hand-soldering of leaded Solder-resist components near mounted components Solder-resist Horizontal component placement ◆Pattern configurations（Inductor layout on panelized［ breakaway］ PC boards） 1-1. The following are examples of good and bad inductor layout; SMD inductors should be located to minimize any possible mechanical stresses from board warp or deflection. Item Not recommended Recommended Position the component at a right angle to the direction of Deflection of the board the mechanical stresses that are anticipated. 1-2. To layout the inductors for the breakaway PC board, it should be noted that the amount of mechanical stresses given will vary depending on inductor layout. An example below should be counted for better design. E D Perforation C A B Slit Magnitude of stress A＞B＝C＞D＞E 1-3. When breaking PC boards along their perforations, the amount of mechanical stress on the inductors can vary according to the method used. The following methods are listed in order from least stressful to most stressful: push-back, slit, V-grooving, and perforation. Thus, any ideal SMD inductor layout must also consider the PCB splitting procedure. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E08R01

3. Considerations for automatic placement ◆Adjustment of mounting machine 1. Excessive impact load should not be imposed on the inductors when mounting onto the PC boards. 2. The maintenance and inspection of the mounter should be conducted periodically. ◆Selection of Adhesives Precautions 1. Mounting inductors with adhesives in preliminary assembly, before the soldering stage, may lead to degraded inductor characteristics unless the following factors are appropriately checked; the size of land patterns, type of adhesive, amount applied, hardening temperature and hardening period. Therefore, it is imperative to consult the manufacturer of the adhesives on proper usage and amounts of adhesive to use. ◆Adjustment of mounting machine 1. If the lower limit of the pick-up nozzle is low, too much force may be imposed on the inductors, causing damage. To avoid this, the following points should be considered before lowering the pick-up nozzle: （1） The lower limit of the pick-up nozzle should be adjusted to the surface level of the PC board after correcting for deflection of the board. （2） The pick-up pressure should be adjusted between 1 and 3N static loads. （3） To reduce the amount of deflection of the board caused by impact of the pick-up nozzle, supporting pins or back-up pins should be used under the PC board. The following diagrams show some typical examples of good pick-up nozzle placement: Item Improper method Proper method chipping Single-sided mounting or cracking supporting pins or back-up pins Double-sided mounting chipping supporting pins or cracking or back-up pins Technical 2. As the alignment pin wears out, adjustment of the nozzle height can cause chipping or cracking of the inductors because of mechanical considerations impact on the inductors. To avoid this, the monitoring of the width between the alignment pin in the stopped position, and maintenance, inspection and replacement of the pin should be conducted periodically. ◆Selection of Adhesives 1. Some adhesives may cause reduced insulation resistance. The difference between the shrinkage percentage of the adhesive and that of the inductors may result in stresses on the inductors and lead to cracking. Moreover, too little or too much adhesive applied to the board may adversely affect component placement, so the following precautions should be noted in the application of adhesives. （1） Required adhesive characteristics a. The adhesive should be strong enough to hold parts on the board during the mounting & solder process. b. The adhesive should have sufficient strength at high temperatures. c. The adhesive should have good coating and thickness consistency. d. The adhesive should be used during its prescribed shelf life. e. The adhesive should harden rapidly. f. The adhesive must not be contaminated. g. The adhesive should have excellent insulation characteristics. h. The adhesive should not be toxic and have no emission of toxic gasses. （2） When using adhesives to mount inductors on a PCB, inappropriate amounts of adhesive on the board may adversely affect component placement. Too little adhesive may cause the inductors to fall off the board during the solder process. Too much adhesive may cause defective soldering due excessive flow of adhesive on to the land or solder pad. ［Recommended conditions］ Amount of adhesives After inductors are bonded Figure 0805 case sizes as examples a a a 0.3mm min b b 100～120μm c Area with no adhesive c c ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E08R01

4. Soldering ◆Selection of Flux 1. Since flux may have a significant effect on the performance of inductors, it is necessary to verify the following conditions prior to use; （1） Flux used should be with less than or equal to 0.1 wt% （Chlorine conversion method） of halogenated content. Flux having a strong acidity content should not be applied. Precautions （2） When soldering inductors on the board, the amount of flux applied should be controlled at the optimum level. （3） When using water-soluble flux, special care should be taken to properly clean the boards. ◆Soldering 1. Temperature, time, amount of solder, etc. are specified in accordance with the following recommended conditions, and please contact us about peak temperature when you use lead-free paste. ◆Selection of Flux 1-1. When too much halogenated substance（Chlorine, etc.）content is used to activate the flux, or highly acidic flux is used, an excessive amount of residue after soldering may lead to corrosion of the terminal electrodes or degradation of insulation resistance on the surface of the Inductor. 1-2. Flux is used to increase solderability in flow soldering, but if too much is applied, a large amount of flux gas may be emitted and may detrimentally affect solderability. To minimize the amount of flux applied, it is recommended to use a flux-bubbling system. 1-3. Since the residue of water-soluble flux is easily dissolved by water content in the air, the residue on the surface of Inductor in high humidity conditions may cause a degradation of insulation resistance and therefore affect the reliability of the components. The cleaning methods and the capability of the machines used should also be considered carefully when selecting water-soluble flux. ◆Soldering 1-1. Preheating when soldering Preheating: Inductors shall be preheated sufficiently, and the temperature difference between the inductors and solder shall be within 130°C. Cooling: The temperature difference between the components and cleaning process should not be greater than 100℃. Inductors are susceptible to thermal shock when exposed to rapid or concentrated heating or rapid cooling. Therefore, the soldering process must be conducted with a great care so as to prevent malfunction of the components due to excessive thermal shock. ［Reflow soldering］ 【Recommended condition for Pb-free soldering】 Caution 300 1. Solder (fillet) should wet up to 1/2 to 1/3 of the thickness of an inductor Peak ideally as shown below: 260℃ Max. Within 10sec. 1/2T～1/3T ） Inductor e（℃ 200 Slow Solder T atur cooling PC board er 2. Because excessive dwell time can detrimentally affect solderability, p m 100 soldering duration shall be kept as close to recommended time as possible. e T Preheating150℃ Heating above 3. The allowable number of reflow soldering is two (2) times. 60sec. Min. 230℃ Technical 40sec. Max. considerations 0 ［Wave soldering］ 【Recommended condition for Pb-free soldering】 Caution 300 1. Make sure the inductors are preheated sufficiently. Peak 2. The temperature difference between the inductor and melted solder 260℃ Max. Within 10sec. should be within 130℃. ℃） 200 120sec. Min. 3. Cooling after soldering should be as gradual as possible. （ 4. The allowable number of wave soldering is one (1) time. ure Slow 5. Wave soldering must not be applied to the inductors designated as for at Preheating cooling mper 100 150℃ reflow soldering only. e T 0 ［Hand soldering］ 【Recommended condition for Pb-free soldering】 Caution 400 1. It is recommended to use a 20W soldering iron with a maximum tip Peak diameter of 1.0 mm. 350℃ Max. Within 3sec. 2. The soldering iron shall not directly touch inductors 300 ） ⊿T 3. The allowable number of hand soldering is one (1) time （℃ Slow cooling ure 200 at er Preheating mp 100 150℃ Min. e T 60sec. Min. 0 （※⊿Ｔ≦150℃） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E08R01

5. Cleaning ◆Cleaning conditions 1. When cleaning the PC board after the Inductors are all mounted, select the appropriate cleaning solution according to the type of flux Precautions used and purpose of the cleaning（e.g. to remove soldering flux or other materials from the production process.） 2. Cleaning conditions should be determined after verifying, through a test run, that the cleaning process does not affect the inductor's characteristics. ◆Cleaning conditions 1. The use of inappropriate solutions can cause foreign substances such as flux residue to adhere to the inductor, resulting in a degradation of the inductor's electrical properties（especially insulation resistance）. 2. Inappropriate cleaning conditions（insufficient or excessive cleaning）may detrimentally affect the performance of the inductors. Technical In the case of ultrasonic cleaning, too much power output can cause excessive vibration of the PC board which may lead to the cracking considerations of the inductor or the soldered portion, or decrease the terminal electrodes' strength. Therefore, the following conditions should be carefully checked; Ultrasonic output 20W/ℓ or less Ultrasonic frequency 40kHz or less Ultrasonic washing period 5 min. or less 6. Resin coating and mold 1. With some type of resins a decomposition gas or chemical reaction vapor may remain inside the resin during the hardening period or while left under normal storage conditions resulting in the deterioration of the inductor's performance. Precautions 2. Thermal expansion and thermal shrinkage characteristics of resins may lead to the deterioration of inductors’ performance. 3. When a resin hardening temperature is higher than inductor operating temperature, the stresses generated by the excessive heat may lead to damage in inductors. 7. Handling ◆Breakaway PC boards（splitting along perforations） 1. When splitting the PC board after mounting inductors and other components, care is required so as not to give any stresses of deflection or twisting to the board. 2. Board separation should not be done manually, but by using the appropriate devices. ◆General handling precautions ・Always wear static control bands to protect against ESD. ・ Keep the inductors away from all magnets and magnetic objects. ・ Use non-magnetic tweezers when handling inductors. Precautions ・ Any devices used with the inductors（ soldering irons, measuring instruments） should be properly grounded. ・ Keep bare hands and metal products（i.e., metal desk）away from inductor electrodes or conductive areas that lead to chip electrodes. ・ Keep inductors away from items that generate magnetic fields such as speakers or coils. ◆Mechanical considerations Be careful not to subject the inductors to excessive mechanical shocks. （1） If inductors are dropped on the floor or a hard surface they should not be used. （2） When handling the mounted boards, be careful that the mounted components do not come in contact with or bump against other boards or components. 8. Storage conditions ◆Storage To maintain the solderability of terminal electrodes and to keep the packaging material in good condition, care must be taken to control temperature and humidity in the storage area. Humidity should especially be kept as low as possible. ・Recommended conditions Precautions Ambient temperature: 30℃ or below Humidity: 70% RH or below The ambient temperature must be kept below 40℃. Even under ideal storage conditions, solderability of inductor is deteriorated as time passes, so inductors should be used within 6 months from the time of delivery. ・Inductor should be kept where no chlorine or sulfur exists in the air. ◆Storage Technical If the parts are stocked in a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of considerations terminal electrodes and deterioration of taping/packaging materials may take place. For this reason, components should be used within 6 months from the time of delivery. If exceeding the above period, please check solderability before using the inductors. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E08R01

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: T aiyo Yuden: HK060310NJ-T HK060312NJ-T HK060315NJ-T HK060318NJ-T HK06031N0S-T HK06031N2S-T HK06031N5S-T HK06031N8S-T HK060322NJ-T HK060327NJ-T HK06032N0S-T HK06032N2S-T HK06032N4S-T HK06032N7S-T HK060333NJ-T HK060339NJ-T HK06033N0S-T HK06033N3S-T HK06033N6S-T HK06033N9S-T HK060347NJ-T HK06034N3S-T HK06034N7S-T HK060356NJ-T HK06035N1S-T HK06035N6S-T HK060368NJ-T HK06036N2S-T HK06036N8J-T HK06037N5J-T HK060382NJ-T HK06038N2J-T HK06039N1J-T HK0603R10J-T HK100510NJ-T HK100510NK-T HK100512NJ-T HK100512NK-T HK100515NJ-T HK100515NK-T HK100518NJ-T HK100518NK-T HK10051N0S-T HK10051N2S-T HK10051N5S-T HK10051N8S-T HK100522NJ-T HK100522NK-T HK100527NJ-T HK100527NK-T HK10052N0S-T HK10052N2S-T HK10052N4S-T HK10052N7S-T HK100533NJ-T HK100533NK-T HK100539NJ-T HK100539NK-T HK10053N0S-T HK10053N3K-T HK10053N3S-T HK10053N6S-T HK10053N9J-T HK10053N9K-T HK10053N9S-T HK100547NJ-T HK100547NK-T HK10054N3S-T HK10054N7J-T HK10054N7K-T HK10054N7S-T HK100556NJ-T HK100556NK-T HK10055N1S-T HK10055N6J-T HK10055N6K-T HK10055N6S-T HK100568NJ-T HK100568NK-T HK10056N2S-T HK10056N8J-T HK10056N8K-T HK10056N8S-T HK10057N5J-T HK100582NJ-T HK100582NK-T HK10058N2J-T HK10058N2K-T HK10058N2S-T HK10059N1J-T HK1005R10J-T HK1005R10K-T HK1005R12J-T HK1005R12K-T HK1005R15J-T HK1005R18J-T HK1005R22J-T HK1005R27J-T HK160810NG-T HK160810NJ-T