GP2Y0A60SZ0F/GP2Y0A60SZLF GP2Y0A60SZ0F GP2Y0A60SZLF Distance Measuring Sensor Unit M easuring distance : 10 to 150 cm Analog output type ■Description ■ Agency approvals/Compliance GP2Y0A60SZ0F/GP2Y0A60SZLF is a distance 1. Compliant with RoHS directive (2002/95/EC) measuring sensor unit, composed of an integrated combination of PSD (position sensitive detector) , IR-LED (infrared emitting diode) and signal processing circuit. The variety of the reflectivity of the object, the ■ Applications environmental temperature and the operating duration are not influenced easily to the distance 1. Touch-less switch detection because of adopting the triangulation (Sanitary equipment, Control of illumination, etc) method. 2. Sensor for energy saving This device outputs the voltage corresponding to (ATM, Copier, Vending machine, Laptop computer, the detection distance. So this sensor can also be LCD monitor, etc) used as a proximity sensor. 3. Amusement equipment (Robot, Arcade game machine, etc) ■Features 1. Distance measuring sensor is united with PSD, infrared LED and signal processing circuit 2. Distance measuring range : 10 to 150 cm 3. Compact size (22.0 × 8.0 × 7.2mm) 4. Long distance measuring type (No external control signal required) 5. Analog output type Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Sheet No.: OP13005EN-A 1

GP2Y0A60SZ0F/GP2Y0A60SZLF ■Schematic GN D Vc c VCTRL PSD V cc Sprigonc easl si ng circuit V ol tage regulator 3 V/ 5V switching A Oscillation circuit Vo K L E D LED drive circuit O u tput circuit A R I L ED M easuring distance IC I L EDFB ・Showing main terminal ・Please use an electric source with an output current of 400mA or more because LED pulse current is more than 300mA. ■Outline GP2Y0A60SZ0F (Drawing No.CY14442j02) Scale : 2/1 Unit : mm Sheet No.: OP13005EN-A 2

GP2Y0A60SZ0F/GP2Y0A60SZLF GP2Y0A60SZLF (Drawing No.CY14591i02) Scale : 2/1 Unit : mm Sheet No.: OP13005EN-A 3

GP2Y0A60SZ0F/GP2Y0A60SZLF ■Absolute maximum ratings (Ta=25°C) Parameter Symbol Ratings Unit Remark Supply voltage Vcc -0.3 to +5.5 V - Output terminal voltage Vo -0.3 to Vcc+0.3 V - Terminal Input terminal voltage 1 - -0.3 to V +0.3 V REG (NC,CH1,CH2,CINT,AR,T) Input terminal voltage 2 - -0.3 to Vcc+0.3 V Terminal (CTRL) Operating temperature Topr -10 to +60 °C - Storage temperature Tstg -40 to +70 °C - Soldering temperature Tsol 260 °C 5s or less/time up 2 times ■Recommended operating conditions Parameter Symbol Rating Unit Remark Supply voltage Vcc 4.5 to 5.5 V 5V Supply voltage Vcc 2.7 to 3.6 V 3V High level input voltage V H 2.3 to Vcc V Operating CTRL Low level input voltage V L MAX 0.2 V Stand-by state CTRL ■Electro-optical Characteristics (Ta=25°C, Vcc=3V) Parameter Symbol Conditions MIN. TYP. MAX. Unit Measuring distance range ΔL (Note 1) 10 - 150 cm Output terminal voltage Vo L=150cm (Note 1) 0.05 0.35 0.65 V Output change at L change Output voltage difference ΔVo 1.35 1.60 1.85 V (10cm → 150cm) (Note 1) Average supply current Icc1 Vcc=3V, V =3V - 33 50 mA CTRL Stand-by supply current Icc2 Vcc=3V, V =0V - - 5 μA CTRL (Ta=25°C, Vcc=5V) Parameter Symbol Conditions MIN. TYP. MAX. Unit Measuring distance range ΔL (Note 1) 10 - 150 cm Output terminal voltage Vo L=150cm (Note 1) 0.15 0.65 1.15 V Output change at L change Output voltage difference ΔVo 2.75 3.00 3.25 V (10cm → 150cm) (Note 1) Average supply current Icc1 Vcc=5V, V =5V - 33 50 mA CTRL Stand-by supply current Icc2 Vcc=5V, V =0V - - 5 μA CTRL ※L : Distance to reflective object (Note 1) Using reflective object : White paper (Made by Kodak Co., Ltd. gray cards R-27・white face, reflective ratio ; 90%) Sheet No.: OP13005EN-A 4

GP2Y0A60SZ0F/GP2Y0A60SZLF ■Timing Chart Vcc (Power supply) V CTRL 16.5ms ± 3.7ms Second nth Distance measuring operating First measurement measurement measureme nt Vo (Output) Unstable output First output MAX 5.0ms Unstable output nth output Second output Sheet No.: OP13005EN-A 5

GP2Y0A60SZ0F/GP2Y0A60SZLF ■Supplements ●Example of output distance characteristics White paper(Reflectance ratio 90%) 4 3.5 3 2.5 ] V ut [ 2 3V operating tp 5Ｖ operating u O 1.5 1 0.5 0 0 50 100 150 Distance [cm] ●This product shall not contain the following materials. Also, the following materials shall not be used in the production process for this product. Materials for ODS : CFC , Halon, Carbon tetrachloride 1.1.1-Trichloroethane (Methyl chloroform) S ●Product mass : Approx. 1.1g (TYP) ●This product does not contain the chemical materials regulated by RoHS directive. (Except for the NOT regulated by RoHS directive.) ●Compliance with each regulation 1) The RoHS directive(2002/95/EC) This product complies with the RoHS directive(2002/95/EC) . Object substances: mercury, lead (except for lead in high melting temperature type solders and glass of electronic components), cadmium, hexavalent chromium, polybrominated biphenyls (PBB) and polybrominated diphenyl ethers (PBDE) 2) Content of six substances specified in Management Methods for Control of Pollution Caused by Electronic Information Products Regulation (Chinese : 电子信息产品污染控制管理办法). Toxic and hazardous substances Hexavalent Polybrominated Polybrominated Category Lead Mercury Cadmium chromium biphenyls diphenyl ethers (Pb) (Hg) (Cd) (Cr6+) (PBB) (PBDE) Distance measuring ✓ ✓ ✓ ✓ ✓ ✓ sensor ✓: indicates that the content of the toxic and hazardous substance in all the homogeneous materials of the part is below the concentration limit requirement as described in S J/T 11363-2006 standard . Sheet No.: OP13005EN-A 6

GP2Y0A60SZ0F/GP2Y0A60SZLF ■Notes [Advice for the optics] ●Lens of this device shall be kept cleanly. There are cases that dust, water or oil and so on deteriorate the characteristics of this device. Please consider in actual application. ●In case that protection is set in front of the emitter and detector portion, the protection cover which has the most efficient transmittance at the emitting wavelength range of LED for this product (λ=870nm±70nm), shall be recommended to use. The face and back of protection cover should be mirror polishing. Also, as there are cases that the characteristics may not be satisfied with according to the distance between the protection cover and this product or the thickness of the protection cover, please use this product after confirming the operation sufficiently in actual application. [Advice for the characteristics] ●In case that there is an object near to light exits of the sensor between the sensor and the detected object, please use this device after confirming sufficiently what the characteristics of this sensor do not change by the object. ●When the detector surface receive direct light from the sun, tungsten lamp and so on, there are cases that it can not measure the distance exactly. Please consider the design that the detector does not receive direct light from such light source. ●Distance between sensor and mirror reflector cannot be measured exactly. ●In case that reflective object has boundary line clearly, there is cases that distance can not measure exactly. At that time, if direction of boundary line and the line between emitter center and detector center are parallels, it is possible to decrease deviation of measuring distance. 〈×〉 〈〇〉 (Incorrect) (Correct) ●In order to decrease measuring error due to moving direction of object, we recommend to mount the sensor like below drawing. (Incorrect) (Correct) 〈×〉 〈〇〉 (Moving direction) (Moving direction) [Notes on handling] ●Please don’t do washing. Washing may deteriorate the characteristics of optical system and so on. Please confirm resistance to chemicals under the actual usage since this product has not been designed against washing. ●Please solder under the condition below within 2 times. ・below 260°C at the tip of soldering tool ・less than 5 seconds Please take care not to let any external force exert on lead pins when soldering. Please do not do soldering by reflow and flow-soldering. Sheet No.: OP13005EN-A 7

GP2Y0A60SZ0F/GP2Y0A60SZLF ■Packing specification GP2Y0A60SZ0F 20 sleeves (5 lines×5stairs) Sleeve Product Packing case Indication side 1. Packing number MAX 20 pieces per sleeve. MAX 500 pieces per case. 2. Close the lid of case and seals with kraft tape, and fill in the blanks of Model No., Quantity and Date. 3. Outside：486×64×77（mm） 4. Indication The content of the indication conforms to EIAJ C-3 and the following items are indicated. Model No., Internal production control name, Quantity, Packing date, Corporate name, Country of origin Sheet No.: OP13005EN-A 8

GP2Y0A60SZ0F/GP2Y0A60SZLF GP2Y0A60SZLF 20 sleeves (5 lines×4stairs) Sleeve Product Packing case Indication side 1. Packing number MAX 20 pieces per sleeve MAX 400 pieces per case. 2. Close the lid of case and seals with kraft tape, and fill in the blanks of Model No., Quantity and Date. 3. Outside：486×64×77（mm） 4. Indication The content of the indication conforms to EIAJ C-3 and the following items are indicated. Model No., Internal production control name, Quantity, Packing date, Corporate name, Country of origin Sheet No.: OP13005EN-A 9

GP2Y0A60SZ0F/GP2Y0A60SZLF ■Important Notices · The circuit application examples in this publication are with equipment that requires higher reliability such as: provided to explain representative applications of SHARP --- Transportation control and safety equipment (i.e., devices and are not intended to guarantee any circuit aircraft, trains, automobiles, etc.) design or license any intellectual property rights. SHARP --- Traffic signals takes no responsibility for any problems related to any --- Gas leakage sensor breakers intellectual property right of a third party resulting from --- Alarm equipment the use of SHARP's devices. --- Various safety devices, etc. (iii) SHARP devices shall not be used for or in connection · Contact SHARP in order to obtain the latest device with equipment that requires an extremely high level of specification sheets before using any SHARP device. reliability and safety such as: SHARP reserves the right to make changes in the --- Space applications specifications, characteristics, data, materials, structure, --- Telecommunication equipment [trunk lines] and other contents described herein at any time without --- Nuclear power control equipment notice in order to improve design or reliability. --- Medical and other life support equipment (e.g., Manufacturing locations are also subject to change without scuba). notice. · If the SHARP devices listed in this publication fall within · Observe the following points when using any devices in the scope of strategic products described in the Foreign this publication. SHARP takes no responsibility for Exchange and Foreign Trade Law of Japan, it is necessary damage caused by improper use of the devices which does to obtain approval to export such SHARP devices. not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor · This publication is the proprietary product of SHARP and meet the following conditions: is copyrighted, with all rights reserved. Under the (i) The devices in this publication are designed for use in copyright laws, no part of this publication may be general electronic equipment designs such as: reproduced or transmitted in any form or by any means, --- Personal computers electronic or mechanical, for any purpose, in whole or in --- Office automation equipment part, without the express written permission of SHARP. --- Telecommunication equipment [terminal] Express written permission is also required before any use --- Test and measurement equipment of this publication may be made by a third party. --- Industrial control --- Audio visual equipment · Contact and consult with a SHARP representative if there --- Consumer electronics are any questions about the contents of this publication. (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection Sheet No.: OP13005EN-A 10