GP2A200LCS0F Series GP2A200LCS0F Detecting Distance : 2 to 22mm *OPIC Output, Series Refl ective Photointerrupter with Connector ■Description ■Agency approvals/Compliance GP2A200LCS0F Series are OPIC output, reflective 1. Compliant with RoHS directive photointerrupters with emitter and detector facing the same direction in a molding that provides non-contact ■Applications sensing. This family of devices uses light modulation to 1. General purpose detection of paper presence or mo- reduce the affects of disturbing light, and the sensor is tion. optimized to work in the selected focal distance. A 3-pin 2. Example: PPC, FAX, Printer connector is included to allow remote-mount or off-board designs. ■Features 1. Refl ective with OPIC Light Modulated Output 2. Highlights : • Includes additional screw fi xing holes • Position pin to prevent mis-alignment • Long focal distance 3. Key Parameters : • Detecting distance : 2 to 22mm (White paper) 5 to 15mm (Black paper) • Undetecting distance : over 90mm (White paper) • Connector : GP2A200LCS0F ; Tyco Electronics AMP K.K. (PN : 292133-3) GP2A200LCSCF ; Tyco Electronics AMP K.K. (PN : 292133-3) GP2A240LCS0F ; Tyco Electronics AMP K.K. (PN : 292133-3) GP2A210LCSJF ; Tyco Electronics AMP K.K. (PN : 4-292133-3) 4. RoHS directive compliant * "OPIC"(Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and a signal- processing Notice The content of data sheet is subject to change without prior notice. In the absence of confi rmation by device specifi cation sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specifi cation sheets before using any SHARP device. Sheet No.: D3-A05101FEN 1 Date Jun. 30. 2005 © SHARP Corporation

GP2A200LCS0F Series ■Internal Connection Diagram Reflective object Demodulator circuit 1 Voltage regulator 1 VCC 2 2 VOUT 3 GND Amp. 3 Comparator Oscillator circuit Sync. detecting circuit ■Outline Dimensions (Unit : mm) GP2A200LCS0F GP2A200LCSCF 33 (6.8) View A 3.1 17.7 5 φ3.2 3. 9 4.5 (7.8) 9.67 6.1 (5.8) 3.2 6.2 6 Optical center 3.5 Connector : 292133-3 φ 12 5.2 (Tyco Electronics AMP K.K.) 1VCC Connector : 292133-3 (Tyco Electronics AMP. K. K) (5.8) 7.8 123VVGCONCUDT 5.2 6 12 3 23VGONUDT 8 4.5 9 5 7.8 2.5 26.5φ3+−00 .2 (0.65) 1 2 3 2 4. Optical center 10.2 φ23+−00..02 21 3.5 2 26.5 0 7 0.9) • Unspecifi ed tolerance 32 • Unspecifi ed tolerance ( shall be as follows ; 4-SR1 View A (6.8) shall be as follows ; Date code Dimensions Tolerance Dimensions Tolerance less than 6 ±0.2 0 2 7.8) less than 6 ±0.2 ( 6 or more 6 or more ±0.3 Date code ±0.3 less than 14 less than 14 14 or more ±0.4 14 or more ±0.4 Product mass : approx. 1.95g • *( ) : Reference dimensions Product mass : approx. 2.3g • *( ) : Reference dimensions GP2A210LCSJF GP2A240LCS0F 33 (6.8) 33 (6.8) 3.1 17.7 3.1 17.7 9 4.5 (7.8) 1VCC 9 4.5 (7.8) 1VCC φ3.2 6.2 6 Optical center 23VGONUDT φ3.2 6.2 6 12 Optical center 23VGONUDT 12 Connector : 292133-3 Connector : 4-292133-3 (Yellow) 7.8 7.8 (Tyco Electronics AMP K.K.) (Tyco Electronics AMP K.K.) 8 4.52.5 26.5 φ3+−00..02 (5 .8) 1 2 3 2 8 4.52.5 26.5 φ3+−00..02 (5 .8)(0.65) 1 2 3 2 • Unspecifi ed tolerance • Unspecifi ed tolerance shall be as follows ; 5 1 shall be as follows ; 9 9 Dimensions Tolerance Dimensions Tolerance Date code Date code less than 6 ±0.2 less than 6 ±0.2 6 or more 6 or more ±0.3 ±0.3 • : Portion Built-in IR-90 fi lter less than 14 less than 14 14 or more ±0.4 14 or more ±0.4 Product mass : approx. 1.95g Product mass : approx. 1.95g • *( ) : Reference dimensions • *( ) : Reference dimensions Connector terminal plating material : Sn Sheet No.: D3-A05101FEN 2

GP2A200LCS0F Series Date code (2 digit) 1st digit 2nd digit Year of production Month of production A.D. Mark Month Mark 2000 0 1 1 2001 1 2 2 2002 2 3 3 2003 3 4 4 2004 4 5 5 2005 5 6 6 2006 6 7 7 2007 7 8 8 2008 8 9 9 2009 9 10 X 2010 0 11 Y : : 12 Z repeats in a 10 year cycle Country of origin Japan Sheet No.: D3-A05101FEN 3

GP2A200LCS0F Series ■Absolute Maximum Ratings (Ta=25˚C) Parameter Symbol Rating Unit Supply voltage VCC −0.5 to +7 V Output voltage V 30 V O *1 Output current I 50 mA OL *2 Operating temperature Topr −10 to +70 ˚C *2 Storage temperature Tstg −20 to +80 ˚C ∗1 Sink current refer to Fig.5. ∗2 The connector should be plugged in/out at normal temperature. ■Electro-optical Characteristics (Ta=25˚C) Parameter Symbol Condhitions MIN. TYP. MAX. Unit Supply voltage VCC − 4.75 − 5.25 V Current dissipation (I) ICC Smoothing value VCC=5V, RL=∞ − − 30 mA *3 Current dissipation (II) ICCP Pulse peak value VCC=5V − − 150 mA Low level output voltage VOL VCC=5V, IOL=16mA, at detecting time − − 0.4 V High level output voltage VOH VCC=5V, RL=1kΩ, at non detecting time 4.5 − − V *4 Non detection distance − − 90 GP2A210LCSJF LLHL KODAK Gray Cards, VCC=5V − − 70 mm L KODAK Gray Cards, VCC=5V − − 2 mm *4 Detection distance HLS Black paper, VCC=5V − − 5 L KODAK Gray Cards , VCC=5V 22 − − mm HLL Black paper, VCC=5V 15 − − *5 Response time ttPPLHHL VCC=5V −− −− 11 mmss Ev1 3 000 − − lx *6 Acceptable illuminance − Ev2 1 500 − − lx ∗3 Refer to Fig.1. ∗4 Refer to Fig.2. ∗5 Refer to Fig.3. *6 Refer to Fig.4. Refl ective object Black paper (black) : Standard refl ective object (provided by SHARP Corporation) KODAK Gray Cards (use the white side refl ects about 90%) : Standard refl ective object (provided by SHARP Corporation) PPC paper : Standard refl ective object (provided by SHARP Corporation) Sheet No.: D3-A05101FEN 4

GP2A200LCS0F Series Fig.1 Test Condition for Peak Pulse Value I CCP R=1Ω VCC=5V Vr 1 V RL=1kΩ 2 VO tW ICCP=Vr/1Ω tP tW (TYP.)=8μs (GP2A240LCS0F : 2.5 to 9.3μs) 3 GND tP (TYP.)=130μs (GP2A240LCS0F : 40 to 150μs) Photointerrupter Fig.2 Test Condition for Detecting Distance Characteristics Reflective object V O OH V ut p ut O V OL Detecting distance L L L Detection surface HLS HLL L L LHS LHL Fig.3 Test Circuit for Response Time Reflective object With reflective object Detection surface RL=1kΩ 1 VCC=5V Without reflective object 2 VO tPHL tPLH V 3 GND OH V OUT 1.5V waveform V OL L Photointerrupter Fig.4 Test Condition for External Disturbing Light Illuminance PPC paper E : At non-detecting E : At detecting V1 V2 Emission/detection Emission/detection surface surface Photointerrupter Light source A Light source A Illuminance shall be that on the reflective object. Photointerrupter Output shall not go from "L" to "H". Illuminance shall be that on the emission/detection surface. 15mm Output shall not go from "H" to "L". Sheet No.: D3-A05101FEN 5

GP2A200LCS0F Series Fig.5 Output Current vs. Fig.6 Low Level Output Voltage vs. Ambient Temperature Ambient Temperature 0.3 VCC=5V 50 At detecting V) IOL=30mA A) 40 (OL (mL ge V 0.2 utput Current IO 2300 vel output volta 0.1 16mA O e w l 5mA 10 Lo 0 0 −10 0 25 50 7075 100 −10 0 10 20 30 40 50 60 70 Ambient temperature Ta (C) Ambient temperature Ta (C) Fig.7 Low Level Output Voltage vs. Fig.8 Dissipation Current(Smoothing Value) Low Level Output Current vs. Ambient Temperature 7 VCC=5V Ta=−10˚C At detecting 6 V) 25˚C (OL mA) 5 70˚C e V (C g C w level output volta 0.1 Dissipation current I 432 o L 1 0.01 0 1 10 100 4.75 4.85 4.95 5.05 5.15 5.25 Low level output current IOL (mA) Supply voltage VCC (V) Remarks : Please be aware that all data in the graph are just for reference and not for guarantee. Sheet No.: D3-A05101FEN 6

GP2A200LCS0F Series ■Design Considerations ●Design guide 1) V terminal : Open collector output O This product operates the light emitter by pulse drive. Please supply the stable supply voltage in order to prevent error operation by pulse current. Please use this device after connecting a capacitor between V and GND for prevention of line noise. O 2) Prevention of detection error Please be careful that you need to keep the direct inverter light away from the photo detecting surface since the device will not operate correctly in such case. In addition, we recommend to make sure the operation test in the actual application. 3) Plugging in/out The connector should be plugged in/out at normal temperature. This product is not designed against irradiation and incorporates non-coherent IRED. ●Parts This product is assembled using the below parts. • Photodetector (Q'ty : 1) [Using a silicon photodiode as light detecting portion, and a bipolar IC as signal processing circuit] Maximum Sensitivity Sensitivity Category Response time (μs) wavelength (nm) wavelength (nm) Phototransistor 900 700 to 1 200 400 • Photo emitter (Q'ty : 1) Maximum light emitting Category Material I/O Frequency (MHz) wavelength (nm) Infrared emitting diode Gallium arsenide (GaAs) 950 0.3 (non-coherent) • Material Case Lens Bottom cover GP2A200LCS0F Polycarbonate resin (Gray) GP2A200LCSCF (UL94 V-2) Black polyphernylene Polycarbonate resin GP2A210LCSJF∗ Sulfi de resin (UL94 V-0) (UL94 V-2) Polycarbonate resin (Navy Blue) GP2A240LCS0F (UL94 V-2) ∗The IR-90 fi lter (Fuji Photo Film Co., Ltd.) is inserted between case and detector side lens. • Others Laser generator is not used. Sheet No.: D3-A05101FEN 7

GP2A200LCS0F Series ■Manufacturing Guidelines ●Cleaning instructions Polycarbonate resin is used as the material of the lens surface. So this product shall not be cleaned by cleaning solvent absolutely. Dust and stain shall clean by air blow, or shall clean by soft cloth. ●Presence of ODC This product shall not contain the following materials. And they are not used in the production process for this product. Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform) Specifi c brominated fl ame retardants such as the PBBOs and PBBs are not used in this product at all. This product shall not contain the following materials banned in the RoHS Directive (2002/95/EC). •Lead, Mercury, Cadmium, Hexavalent chromium, Polybrominated biphenyls (PBB), Polybrominated diphenyl ethers (PBDE). Sheet No.: D3-A05101FEN 8

GP2A200LCS0F Series ■Package specifi cation ●Case package Package materials Anti-static plastic bag : Polyethtylene Moltopren : Urethane Packing case : Corrugated fi berboard Package method 100 pcs of products shall be packaged in a plastic bag, Ends shall be sealed by stapler. The bottom ot the packing case is covered with moltopren, and 2 plastic bags shall be put int the packing case. Moltopren should be located after all product are settled (1 packing conteains 200 pcs). Packing composition Moltopren plastic bag Packing case Sheet No.: D3-A05101FEN 9

GP2A200LCS0F Series ■Important Notices · The circuit application examples in this publication with equipment that requires higher reliability such as: are provided to explain representative applications of --- Transportation control and safety equipment (i.e., SHARP devices and are not intended to guarantee any aircraft, trains, automobiles, etc.) circuit design or license any intellectual property rights. --- Traffi c signals SHARP takes no responsibility for any problems related --- Gas leakage sensor breakers to any intellectual property right of a third party resulting --- Alarm equipment from the use of SHARP's devices. --- Various safety devices, etc. (iii) SHARP devices shall not be used for or in · Contact SHARP in order to obtain the latest device connection with equipment that requires an extremely specification sheets before using any SHARP device. high level of reliability and safety such as: SHARP reserves the right to make changes in the --- Space applications specifi cations, characteristics, data, materials, structure, --- Telecommunication equipment [trunk lines] and other contents described herein at any time --- Nuclear power control equipment without notice in order to improve design or reliability. --- Medical and other life support equipment (e.g., Manufacturing locations are also subject to change scuba). without notice. · If the SHARP devices listed in this publication fall · Observe the following points when using any devices within the scope of strategic products described in the in this publication. SHARP takes no responsibility for Foreign Exchange and Foreign Trade Law of Japan, it damage caused by improper use of the devices which is necessary to obtain approval to export such SHARP does not meet the conditions and absolute maximum devices. ratings to be used specifi ed in the relevant specifi cation sheet nor meet the following conditions: · This publication is the proprietary product of SHARP (i) The devices in this publication are designed for use and is copyrighted, with all rights reserved. Under in general electronic equipment designs such as: the copyright laws, no part of this publication may be --- Personal computers reproduced or transmitted in any form or by any means, --- Offi ce automation equipment electronic or mechanical, for any purpose, in whole or in --- Telecommunication equipment [terminal] part, without the express written permission of SHARP. --- Test and measurement equipment Express written permission is also required before any --- Industrial control use of this publication may be made by a third party. --- Audio visual equipment --- Consumer electronics · Contact and consult with a SHARP representative (ii) Measures such as fail-safe function and redundant if there are any questions about the contents of this design should be taken to ensure reliability and safety publication. when SHARP devices are used for or in connection [H176] Sheet No.: D3-A05101FEN 10