[ For High Quality and/or Reliability Equipment Notice for TAIYO YUDEN Products (Automotive Electronic Equipment / Industrial Equipment) ] Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product information in this catalog is as of October 2018. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or use of our products. Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or equipment incorporating our products, which are caused under the conditions other than those specified in this catalog or individual product specification sheets. ■ Please contact TAIYO YUDEN for further details of product specifications as the individual product specification sheets are available. ■ Please conduct validation and verification of our products in actual condition of mounting and operating environment before using our products. ■ The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office equipment, information and communication equipment), medical equipment classified as Class I or II by IMDRF, industrial equipment, and automotive interior applications, etc. Please be sure to contact TAIYO YUDEN for further information before using the products for any equipment which may directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation, automotive powertrain control system, train control system, and ship control system, traffic signal equipment, medical equipment classified as Class III by IMDRF). Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g., aerospace equipment, aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control equipment, undersea equipment, military equipment). *Note: There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g., in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN. Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment. When our products are used even for high safety and/or reliability-required devices or circuits of general electronic equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to install a protection circuit as necessary. Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above. ■ Information contained in this catalog is intended to convey examples of typical performances and/or applications of our products and is not intended to make any warranty with respect to the intellectual property rights or any other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights. ■ Please note that the scope of warranty for our products is limited to the delivered our products themselves and TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products. Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in accordance with such agreement. ■ The contents of this catalog are applicable to our products which are purchased from our sales offices or authorized distributors (hereinafter“ TAIYO YUDEN’s official sales channel”). Please note that the contents of this catalog are not applicable to our products purchased from any seller other than TAIYO YUDEN’s official sales channel. ■ Caution for Export Some of our products listed in this catalog may require specific procedures for export according to“ U.S. Export Administration Regulations”,“ Foreign Exchange and Foreign Trade Control Law” of Japan, and other applicable regulations. Should you have any questions on this matter, please contact our sales staff. 19

Automotive Application Guide We classify automotive electronic equipment into the following four application categories and set usable application categories for each of our products. When using our products for automotive electronic equipment, please be sure to check such application categories and use our products accordingly. Should you have any questions on this matter, please contact us. Category Automotive Electronic Equipment (Typical Example) ・Engine ECU (Electronically Controlled Fuel Injector) A ・Cruise Control Unit u t ・4WS (4 Wheel Steering) o m POWERTRAIN ・Automatic Transmission o t ・Power Steering iv e ・HEV/PHV/EV Core Control (Battery, Inverter, DC-DC) A ・Automotive Locator (Car location information providing device), etc. p p ・ABS (Anti-Lock Brake System) lic a ・ESC (Electronic Stability Control) t SAFETY io ・Airbag n ・ADAS (Equipment that directly controls running, turning and stopping), etc. G u ・Wiper id ・Automatic Door e ・Power Window ・Keyless Entry System BODY & CHASSIS ・Electric Door Mirror ・Interior Lighting ・LED Headlight ・TPMS (Tire Pressure Monitoring System) ・Anti-Theft Device (Immobilizer), etc. ・Car Infotainment System ・ITS/Telematics System INFOTAINMENT ・Instrument Cluster ・ADAS (Sensor, Equipment that is not interlocked with safety equipment or powertrain), etc. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 19 15

MULTILAYER CERAMIC CAPACITORS MULTILAYER CERAMIC CAPACITORS REFLOW REFLOW A EACE-C Q-2Q02000 ■PART NUMBER J M K 3 1 6 △ B J 1 0 6 M L H T △ △＝Blank space ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ ①Rated voltage ③End termination Code Rated voltage［VDC］ Code End termination A 4 K Plated J 6.3 J Soft Termination L 10 S Cu Internal Electrodes (For High Frequency) E 16 F High Reliability Application C E T 25 R G 35 ④Dimension（L×W） A U 50 Dimensions M Type EIA（inch） IC H 100 （L×W）［mm］ Q 250 063 0.6 × 0.3 0201 C S 630 1.0 × 0.5 0402 A 105 P 0.52× 1.0 ※ 0204 A ②Series name 1.6 × 0.8 0603 C 107 IT Code Series name 0.8 × 1.6 ※ 0306 O M Multilayer ceramic capacitor 212 2.0 × 1.25 0805 R V Multilayer ceramic capacitor for high frequency 1.25× 2.0 ※ 0508 S W LW reverse type multilayer capacitor 316 3.2 × 1.6 1206 325 3.2 × 2.5 1210 432 4.5 × 3.2 1812 Note : ※LW reverse type（□WK） only ⑤Dimension tolerance Code Type L［mm］ W［mm］ T［mm］ △ ALL Standard Standard Standard 063 0.6±0.05 0.3±0.05 0.3±0.05 105 1.0±0.10 0.5±0.10 0.5±0.10 107 1.6＋0.15/－0.05 0.8＋0.15/－0.05 0.8＋0.15/－0.05 A 0.85±0.10 212 2.0＋0.15/－0.05 1.25＋0.15/－0.05 1.25＋0.15/－0.05 316 3.2±0.20 1.6±0.20 1.6±0.20 325 3.2±0.30 2.5±0.30 2.5±0.30 105 1.0＋0.15/－0.05 0.5＋0.15/－0.05 0.5＋0.15/－0.05 107 1.6＋0.20/－0 0.8＋0.20/－0 0.8＋0.20/－0 B 0.85±0.10 212 2.0＋0.20/－0 1.25＋0.20/－0 1.25＋0.20/－0 316 3.2±0.30 1.6±0.30 1.6±0.30 105 1.0＋0.20/－0 0.5＋0.20/－0 0.5＋0.20/－0 C 107 1.6＋0.25/－0 0.8＋0.25/－0 0.8＋0.25/－0 212 2.0＋0.25/－0 1.25＋0.25/－0 1.25＋0.25/－0 212 2.0±0.15 1.25±0.15 0.85±0.15 1.15±0.20 K 316 3.2±0.20 1.6±0.20 1.6±0.20 325 3.2±0.50 2.5±0.30 2.5±0.30 Note: ｃｆ. STANDARD EXTERNAL DIMENSIONS △= Blank space ⑥Temperature characteristics code ■High dielectric type Applicable Temperature Capacitance Tolerance Code Ref. Temp.［℃］ Capacitance change standard range［℃］ tolerance code ±10％ K BJ EIA X5R －55～＋ 85 25 ±15％ ±20％ M ±10％ K C6 EIA X6S －55～＋105 25 ±22％ ±20％ M ±10％ K B7 EIA X7R －55～＋125 25 ±15％ ±20％ M ±10％ K C7 EIA X7S －55～＋125 25 ±22％ ±20％ M ±10％ K D7 EIA X7T －55～＋125 25 ＋22％/－33％ ±20％ M hq_c_mlcc_e-E07R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 18 19

■Temperature compensating type Applicable Temperature Capacitance Tolerance Code Ref. Temp.［℃］ Capacitance change standard range［℃］ tolerance code ±0.1pF B JIS CG 20 ±0.25pF C ±0.5pF D CG －55～＋125 0±30ppm/℃ ±1pF F EIA C0G 25 ±2％ G ±5％ J ⑦Nominal capacitance ⑨Thickness Code Code Thickness［mm］ Nominal capacitance （example） P 0.3 0R5 0.5pF T 010 1pF V 0.5 100 10pF C 0.7(107type or more) 101 100pF A 0.8 102 1,000pF D 0.85(212type or more) C 103 0.01μF F 1.15 E R 104 0.1μF G 1.25 A 105 1.0μF L 1.6 M 106 10μF N 1.9 IC 107 100μF M 2.5 C Note : R＝Decimal point A ⑩Special code P A ⑧Capacitance tolerance Code Special code C Code Capacitance tolerance H MLCC for Industrial and Automotive IT A ±0.05pF O B ±0.1pF ⑪Packaging R S C ±0.25pF Code Packaging D ±0.5pF F φ178mm Taping （2mm pitch） G ±2％ R φ178mm Embossed Taping （4mm pitch） J ±5％ T φ178mm Taping （4mm pitch） K ±10％ φ178mm Taping （4mm pitch, 1000 pcs/reel） P M ±20％ 325 type（Thickness code M） ⑫Internal code Code Internal code △ Standard hq_c_mlcc_e-E07R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 19 19

■STANDARD EXTERNAL DIMENSIONS W Dimension [mm] （inch） Type( EIA ) L L W T *1 e 0.6±0.03 0.3±0.03 0.3±0.03 0.15±0.05 □MK063（0201） T T (0.024±0.001) (0.012±0.001) (0.012±0.001) (0.006±0.002) □MK105（0402） 1.0±0.05 0.5±0.05 0.5±0.05 0.25±0.10 V e □MF105（0402） (0.039±0.002) (0.020±0.002) (0.020±0.002) (0.010±0.004) 0.52±0.05 1.0±0.05 0.3±0.05 0.18±0.08 □WK105（0204）※ P (0.020±0.002) (0.039±0.002) (0.012±0.002) (0.007±0.003) □MK107（0603） 1.6±0.10 0.8±0.10 0.8±0.10 0.35±0.25 A □MF107（0603） (0.063±0.004) (0.031±0.004) (0.031±0.004) (0.014±0.010) L 1.6±0.10 0.8±0.10 0.8±0.10 0.35＋0.3/－0.25 □MJ107（0603） A (0.063±0.004) (0.031±0.004) (0.031±0.004) (0.014＋0.012/－0.010) W 1.6±0.10 0.8±0.10 0.7±0.10 0.35±0.25 □VS107（0603） C (0.063±0.004) (0.031±0.004) (0.028±0.004) (0.014±0.010) 0.8±0.10 1.6±0.10 0.5±0.05 0.25±0.15 □WK107（0306）※ V C (0.031±0.004) (0.063±0.004) (0.020±0.002) (0.010±0.006) E T 0.85±0.10 R D A □MK212（0805） 2.0±0.10 1.25±0.10 (0.033±0.004) 0.5±0.25 M e □MF212（0805） (0.079±0.004) (0.049±0.004) 1.25±0.10 (0.020±0.010) IC (0.049±0.004) G ※ LW reverse type C 0.85±0.10 D A 2.0±0.10 1.25±0.10 (0.033±0.004) 0.5＋0.35/－0.25 □MJ212（0805） P (0.079±0.004) (0.049±0.004) 1.25±0.10 （0.020＋0.014/－0.010） A G C (0.049±0.004) IT 2.0±0.10 1.25±0.10 0.85±0.10 0.5±0.25 □VS212（0805） D O (0.079±0.004) (0.049±0.004) (0.033±0.004) (0.020±0.010) R 1.25±0.15 2.0±0.15 0.85±0.10 0.3±0.2 S □WK212（0508）※ D (0.049±0.006) (0.079±0.006) (0.033±0.004) (0.012±0.008) 1.15±0.10 Ｆ □MK316（1206） 3.2±0.15 1.6±0.15 (0.045±0.004) 0.5＋0.35/－0.25 □MF316（1206） (0.126±0.006) (0.063±0.006) 1.6±0.20 （0.020＋0.014/－0.010） L (0.063±0.008) 1.15±0.10 Ｆ 3.2±0.15 1.6±0.15 (0.045±0.004) 0.6＋0.4/－0.3 □MJ316（1206） (0.126±0.006) (0.063±0.006) 1.6±0.20 （0.024＋0.016/－0.012） L (0.063±0.008) 1.15±0.10 F (0.045±0.004) □MK325（1210） 3.2±0.30 2.5±0.20 1.9±0.20 0.6±0.3 N □MF325（1210） (0.126±0.012) (0.098±0.008) (0.075±0.008) (0.024±0.012) 2.5±0.20 M (0.098±0.008) 1.9±0.20 N 3.2±0.30 2.5±0.20 (0.075±0.008) 0.6＋0.4/－0.3 □MJ325（1210） (0.126±0.012) (0.098±0.008) 2.5±0.20 （0.024＋0.016/－0.012） M (0.098±0.008) 4.5±0.40 3.2±0.30 2.5±0.20 0.9±0.6 □MK432（1812） M (0.177±0.016) (0.126±0.012) (0.098±0.008) (0.035±0.024) Note : ※. LW reverse type, *1.Thickness code hq_c_mlcc_e-E07R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 20 19

■STANDARD QUANTITY Dimension Standard quantity［pcs］ Type EIA（inch） ［ｍｍ］ Code Paper tape Embossed tape 063 0201 0.3 T 15000 － 0402 0.5 V 105 10000 － 0204 ※ 0.30 P 0.7 C 4000 － 0.8 A 3000 0603 0.8 A － 107 （Soft Termination） 3000 0.8 A － （Soft Termination） 0306 ※ 0.50 V － 4000 0.85 D 4000 － 1.25 G － 3000 0805 212 2000 1.25 G － （Soft Termination） C 0508 ※ 0.85 D 4000 － E 1.15 F － 3000 R 316 1206 1.6 L － 2000 A M 1.15 F 325 1210 1.9 N － 2000 IC 2.5 M － 500（T），1000（P） C 432 1812 2.5 M － 500 A P Note : ※.LW Reverse type（□WK） A C IT O R S hq_c_mlcc_e-E07R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 19 21

■PART NUMBER ・ All the Multilayer Ceramic Capacitors of the catalog lineup are RoHS compliant. ・ Capacitance tolerance code is applied to [] of part number. ・ All the Multilayer Ceramic Capacitors in the catalog lineup are applicable for reflow-soldering. Note) ・ The exchange of individual specifications is necessary depending on the application and circuit condition. Please contact Taiyo Yuden sales channels. ・ *1: Automotive (AEC-Q200 Qualified) products for BODY & CHASSIS, and INFOTAINMENT. Please check ”Automotive Application Guide” for further details before using the products. 　　＜　 　A　EC　-　Q　2　00　 　：AEC-Q200 qualified＞ 　　　　　All the Multilayer Ceramic Capacitors of　*1 marks are tested based on the test conditions and methods defined in AEC-Q200 by family item. 　　　　　125℃　products：　AEC-Q200　Grade1 (we conduct the evaluation at the test condition of Grade1.) 　　　　　105℃　products：　AEC-Q200　Grade2 (we conduct the evaluation at the test condition of Grade2.) 　　　　　　85℃　products：　AEC-Q200　Grade3 (we conduct the evaluation at the test condition of Grade3.) 　　　　　Please consult with TAIYO YUDEN’s official sales channel for the details of the product specification and AEC-Q200 test results, etc., 　　　　　and please review and　approve TAIYO YUDEN's product specification before ordering. ・ *2: Industrial　products and Medical products ・ *3: For standard case size, please kindly refer to ④Dimension, ⑤Dimension tolerance,　⑨Thickness and STANDARD EXTERNAL DIMENSIONS. Multilayer Ceramic Capacitors (High dielectric type) C ●105TYPE (Demension:1.0×0.5mm　JIS:1005　EIA:0402） E R 【Temperature Characteristic BJ : X5R（－55～＋85℃）】　0.5mm thickness（V） A M Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance toClaepraanccitea n[c％e] t a[％nδ] Rated vHoTltLaTge x ％ Thickness*3 [mm] Note IC UMK105 BJ471[]VHF X5R 470p ±10, ±20 2.5 200 0.5±0.05 *1, *2 C UMK105 BJ102[]VHF X5R 1000p ±10, ±20 2.5 200 0.5±0.05 *1, *2 A UMK105 BJ152[]VHF X5R 1500p ±10, ±20 2.5 200 0.5±0.05 *1, *2 P UMK105 BJ222[]VHF X5R 2200p ±10, ±20 2.5 200 0.5±0.05 *1, *2 A UMK105 BJ332[]VHF X5R 3300p ±10, ±20 2.5 200 0.5±0.05 *1, *2 C UMK105 BJ472[]VHF 50 X5R 4700p ±10, ±20 2.5 200 0.5±0.05 *1, *2 IT UMK105 BJ682[]VHF X5R 6800p ±10, ±20 2.5 150 0.5±0.05 *1, *2 O UMK105 BJ103[]VHF X5R 0.01μ ±10, ±20 3.5 200 0.5±0.05 *1, *2 R UMK105 BJ223[]VHF X5R 0.022μ ±10, ±20 5 200 0.5±0.05 *1, *2 S UMK105 BJ473[]VHF X5R 0.047μ ±10, ±20 5 200 0.5±0.05 *1, *2 UMK105 BJ104[]VHF X5R 0.1μ ±10, ±20 10 150 0.5±0.05 *1, *2 TMK105 BJ472[]VHF X5R 4700p ±10, ±20 2.5 200 0.5±0.05 *1, *2 TMK105 BJ682[]VHF X5R 6800p ±10, ±20 2.5 200 0.5±0.05 *1, *2 TMK105 BJ103[]VHF X5R 0.01μ ±10, ±20 3.5 200 0.5±0.05 *1, *2 TMK105 BJ153[]VHF X5R 0.015μ ±10, ±20 3.5 200 0.5±0.05 *1, *2 TMK105 BJ223[]VHF X5R 0.022μ ±10, ±20 3.5 200 0.5±0.05 *1, *2 25 TMK105 BJ333[]VHF X5R 0.033μ ±10, ±20 3.5 150 0.5±0.05 *1, *2 TMK105 BJ473[]VHF X5R 0.047μ ±10, ±20 3.5 150 0.5±0.05 *1, *2 TMK105 BJ104[]VHF X5R 0.1μ ±10, ±20 5 150 0.5±0.05 *1, *2 TMK105 BJ224[]VHF X5R 0.22μ ±10, ±20 10 150 0.5±0.05 *1, *2 TMK105ABJ474[]VHF X5R 0.47μ ±10, ±20 10 150 0.5±0.10 *1, *2 EMK105 BJ103[]VHF X5R 0.01μ ±10, ±20 3.5 200 0.5±0.05 *1, *2 EMK105 BJ153[]VHF X5R 0.015μ ±10, ±20 3.5 200 0.5±0.05 *1, *2 EMK105 BJ223[]VHF X5R 0.022μ ±10, ±20 3.5 200 0.5±0.05 *1, *2 EMK105 BJ333[]VHF X5R 0.033μ ±10, ±20 3.5 150 0.5±0.05 *1, *2 EMK105 BJ473[]VHF 16 X5R 0.047μ ±10, ±20 3.5 150 0.5±0.05 *1, *2 EMK105 BJ104[]VHF X5R 0.1μ ±10, ±20 5 150 0.5±0.05 *1, *2 EMK105 BJ224[]VHF X5R 0.22μ ±10, ±20 10 150 0.5±0.05 *1, *2 EMK105ABJ474[]VHF X5R 0.47μ ±10, ±20 10 150 0.5±0.10 *1, *2 EMK105 BJ105[]VHF X5R 1μ ±10, ±20 10 150 0.5±0.05 *1, *2 LMK105 BJ333[]VHF X5R 0.033μ ±10, ±20 3.5 150 0.5±0.05 *1, *2 LMK105 BJ473[]VHF X5R 0.047μ ±10, ±20 3.5 150 0.5±0.05 *1, *2 LMK105 BJ104[]VHF X5R 0.1μ ±10, ±20 5 150 0.5±0.05 *1, *2 LMK105 BJ224[]VHF 10 X5R 0.22μ ±10, ±20 5 150 0.5±0.05 *1, *2 LMK105ABJ474[]VHF X5R 0.47μ ±10, ±20 10 150 0.5±0.10 *1, *2 LMK105 BJ105[]VHF X5R 1μ ±10, ±20 10 150 0.5±0.05 *1, *2 LMK105ABJ225[]VHF X5R 2.2μ ±10, ±20 10 150 0.5±0.10 *1, *2 JMK105 BJ104[]VHF X5R 0.1μ ±10, ±20 5 150 0.5±0.05 *1, *2 JMK105 BJ224[]VHF X5R 0.22μ ±10, ±20 5 150 0.5±0.05 *1, *2 JMK105 BJ474[]VHF X5R 0.47μ ±10, ±20 10 150 0.5±0.05 *1, *2 6.3 JMK105 BJ105[]VHF X5R 1μ ±10, ±20 10 150 0.5±0.05 *1, *2 JMK105 BJ225[]VHF X5R 2.2μ ±10, ±20 10 150 0.5±0.05 *1, *2 JMK105BBJ475MVHF X5R 4.7μ ±20 10 150 0.5+0.15/-0.05 *1, *2 AMK105 BJ225[]VHF X5R 2.2μ ±10, ±20 10 150 0.5±0.05 *1, *2 AMK105BBJ475MVHF 4 X5R 4.7μ ±20 10 150 0.5+0.15/-0.05 *1, *2 AMK105CBJ106MVHF X5R 10μ ±20 10 150 0.5+0.20/-0 *1, *2 hq_c_mlcc_e-E07R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 22 19

■PART NUMBER 【Temperature Characteristic B7 : X7R（－55～＋125℃）】　0.5mm thickness（V） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance toClaepraanccitea n[c％e] t a[％nδ] Rated vHoTltLaTge x ％ Thickness*3 [mm] Note UMK105 B7221[]VHF X7R 220p ±10, ±20 2.5 200 0.5±0.05 *1, *2 UMK105 B7331[]VHF X7R 330p ±10, ±20 2.5 200 0.5±0.05 *1, *2 UMK105 B7471[]VHF X7R 470p ±10, ±20 2.5 200 0.5±0.05 *1, *2 UMK105 B7681[]VHF X7R 680p ±10, ±20 2.5 200 0.5±0.05 *1, *2 UMK105 B7102[]VHF X7R 1000p ±10, ±20 2.5 200 0.5±0.05 *1, *2 UMK105 B7152[]VHF X7R 1500p ±10, ±20 2.5 200 0.5±0.05 *1, *2 UMK105 B7222[]VHF X7R 2200p ±10, ±20 2.5 200 0.5±0.05 *1, *2 50 UMK105 B7332[]VHF X7R 3300p ±10, ±20 2.5 200 0.5±0.05 *1, *2 UMK105 B7472[]VHF X7R 4700p ±10, ±20 2.5 150 0.5±0.05 *1, *2 UMK105 B7682[]VHF X7R 6800p ±10, ±20 2.5 150 0.5±0.05 *1, *2 UMK105 B7103[]VHF X7R 0.01μ ±10, ±20 3.5 150 0.5±0.05 *1, *2 UMK105 B7223[]VHF X7R 0.022μ ±10, ±20 10 200 0.5±0.05 *1, *2 UMK105 B7473[]VHF X7R 0.047μ ±10, ±20 10 200 0.5±0.05 *1, *2 UMK105 B7104[]VHF X7R 0.1μ ±10, ±20 10 150 0.5±0.05 *1, *2 TMK105 B7472[]VHF X7R 4700p ±10, ±20 2.5 200 0.5±0.05 *1, *2 TMK105 B7682[]VHF X7R 6800p ±10, ±20 2.5 200 0.5±0.05 *1, *2 TMK105 B7103[]VHF X7R 0.01μ ±10, ±20 3.5 200 0.5±0.05 *1, *2 C TMK105 B7153[]VHF 25 X7R 0.015μ ±10, ±20 3.5 150 0.5±0.05 *1, *2 E TMK105 B7223[]VHF X7R 0.022μ ±10, ±20 3.5 150 0.5±0.05 *1, *2 R TMK105 B7333[]VHF X7R 0.033μ ±10, ±20 3.5 150 0.5±0.05 *1, *2 A TMK105 B7473[]VHF X7R 0.047μ ±10, ±20 3.5 150 0.5±0.05 *1, *2 M TEMMKK110055 BB77110034[[]]VVHHFF XX77RR 0.00.11μμ ±±1100,, ±±2200 31.05 125000 00..55±±00..0055 **11,, **22 IC EMK105 B7153[]VHF X7R 0.015μ ±10, ±20 3.5 150 0.5±0.05 *1, *2 C EMK105 B7223[]VHF X7R 0.022μ ±10, ±20 3.5 150 0.5±0.05 *1, *2 A EMK105 B7333[]VHF 16 X7R 0.033μ ±10, ±20 3.5 150 0.5±0.05 *1, *2 P EMK105 B7473[]VHF X7R 0.047μ ±10, ±20 3.5 150 0.5±0.05 *1, *2 A EMK105 B7104[]VHF X7R 0.1μ ±10, ±20 5 150 0.5±0.05 *1, *2 C EMK105 B7224[]VHF X7R 0.22μ ±10, ±20 10 150 0.5±0.05 *1, *2 IT LMK105 B7473[]VHF X7R 0.047μ ±10, ±20 3.5 150 0.5±0.05 *1, *2 O LMK105 B7104[]VHF 10 X7R 0.1μ ±10, ±20 5 150 0.5±0.05 *1, *2 R LMK105 B7224[]VHF X7R 0.22μ ±10, ±20 10 150 0.5±0.05 *1, *2 S JMK105 B7104[]VHF X7R 0.1μ ±10, ±20 5 150 0.5±0.05 *1, *2 JMK105 B7224[]VHF 6.3 X7R 0.22μ ±10, ±20 10 150 0.5±0.05 *1, *2 JMK105 B7474[]VHF X7R 0.47μ ±10, ±20 10 150 0.5±0.05 *1, *2 AMK105 B7474[]VHF 4 X7R 0.47μ ±10, ±20 10 150 0.5±0.05 *1, *2 ●107TYPE　 (Dimension:1.6×0.8mm　JIS:1608　EIA:0603） 【Temperature Characteristic BJ : X5R（－55～＋85℃）】　0.8mm thickness（A） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance toClaepraanccitea n[c％e] t a[％nδ] Rated vHoTltLaTge x ％ Thickness*3 [mm] Note UMK107 BJ104[]AHT X5R 0.1μ ±10, ±20 3.5 150 0.8±0.10 *1, *2 UMK107 BJ224[]AHT X5R 0.22μ ±10, ±20 10 150 0.8±0.10 *1, *2 50 UMK107 BJ474[]AHT X5R 0.47μ ±10, ±20 10 150 0.8±0.10 *1, *2 UMK107ABJ105[]AHT X5R 1μ ±10, ±20 10 150 0.8+0.15/-0.05 *1, *2 GMK107 BJ223[]AHT X5R 0.022μ ±10, ±20 2.5 200 0.8±0.10 *1, *2 GMK107 BJ473[]AHT X5R 0.047μ ±10, ±20 3.5 200 0.8±0.10 *1, *2 GMK107 BJ104[]AHT X5R 0.1μ ±10, ±20 3.5 150 0.8±0.10 *1, *2 35 GMK107 BJ224[]AHT X5R 0.22μ ±10, ±20 10 150 0.8±0.10 *1, *2 GMK107ABJ474[]AHT X5R 0.47μ ±10, ±20 10 150 0.8+0.15/-0.05 *1, *2 GMK107 BJ105[]AHT X5R 1μ ±10, ±20 10 150 0.8±0.10 *1, *2 TMK107 BJ223[]AHT X5R 0.022μ ±10, ±20 2.5 200 0.8±0.10 *1, *2 TMK107 BJ473[]AHT X5R 0.047μ ±10, ±20 3.5 200 0.8±0.10 *1, *2 TMK107 BJ104[]AHT X5R 0.1μ ±10, ±20 3.5 150 0.8±0.10 *1, *2 TMK107 BJ224[]AHT 25 X5R 0.22μ ±10, ±20 5 150 0.8±0.10 *1, *2 TMK107 BJ474[]AHT X5R 0.47μ ±10, ±20 3.5 150 0.8±0.10 *1, *2 TMK107 BJ105[]AHT X5R 1μ ±10, ±20 10 150 0.8±0.10 *1, *2 TMK107BBJ225[]AHT X5R 2.2μ ±10, ±20 10 150 0.8+0.20/-0 *1, *2 EMK107 BJ104[]AHT X5R 0.1μ ±10, ±20 3.5 150 0.8±0.10 *1, *2 EMK107 BJ224[]AHT X5R 0.22μ ±10, ±20 5 150 0.8±0.10 *1, *2 EMK107 BJ474[]AHT X5R 0.47μ ±10, ±20 3.5 150 0.8±0.10 *1, *2 16 EMK107 BJ105[]AHT X5R 1μ ±10, ±20 5 150 0.8±0.10 *1, *2 EMK107ABJ225[]AHT X5R 2.2μ ±10, ±20 10 150 0.8+0.15/-0.05 *1, *2 EMK107BBJ475[]AHT X5R 4.7μ ±10, ±20 10 150 0.8+0.20/-0 *1, *2 LMK107 BJ474[]AHT X5R 0.47μ ±10, ±20 3.5 150 0.8±0.10 *1, *2 LMK107 BJ105[]AHT X5R 1μ ±10, ±20 5 150 0.8±0.10 *1, *2 LMK107 BJ225[]AHT 10 X5R 2.2μ ±10, ±20 10 150 0.8±0.10 *1, *2 LMK107 BJ475[]AHT X5R 4.7μ ±10, ±20 10 150 0.8±0.10 *1, *2 LMK107BBJ106MAHT X5R 10μ ±20 10 150 0.8+0.20/-0 *1, *2 JMK107 BJ105[]AHT X5R 1μ ±10, ±20 5 150 0.8±0.10 *1, *2 JMK107 BJ225[]AHT X5R 2.2μ ±10, ±20 10 150 0.8±0.10 *1, *2 6.3 JMK107 BJ475[]AHT X5R 4.7μ ±10, ±20 10 150 0.8±0.10 *1, *2 JMK107ABJ106[]AHT X5R 10μ ±10, ±20 10 150 0.8+0.15/-0.05 *1, *2 AMK107ABJ106[]AHT X5R 10μ ±10, ±20 10 150 0.8+0.15/-0.05 *1, *2 4 AMK107BBJ226MAHT X5R 22μ ±20 10 150 0.8+0.20/-0 *1, *2 hq_c_mlcc_e-E07R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 19 23

■PART NUMBER 【Temperature Characteristic B7 : X7R（－55～＋125℃）, C7 : X7S（－55～＋125℃）, D7 : X7T（－55～＋125℃）】　0.8mm thickness（A） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance toClaepraanccitea n[c％e] t a[％nδ] Rated vHoTltLaTge x ％ Thickness*3 [mm] Note UMK107 B7102[]AHT X7R 1000p ±10, ±20 3.5 200 0.8±0.10 *1, *2 UMK107 B7152[]AHT X7R 1500p ±10, ±20 3.5 200 0.8±0.10 *1, *2 UMK107 B7222[]AHT X7R 2200p ±10, ±20 3.5 200 0.8±0.10 *1, *2 UMK107 B7332[]AHT X7R 3300p ±10, ±20 3.5 200 0.8±0.10 *1, *2 UMK107 B7472[]AHT X7R 4700p ±10, ±20 3.5 200 0.8±0.10 *1, *2 UMK107 B7682[]AHT X7R 6800p ±10, ±20 3.5 200 0.8±0.10 *1, *2 UMK107 B7103[]AHT X7R 0.01μ ±10, ±20 3.5 200 0.8±0.10 *1, *2 50 UMK107 B7153[]AHT X7R 0.015μ ±10, ±20 3.5 200 0.8±0.10 *1, *2 UMK107 B7223[]AHT X7R 0.022μ ±10, ±20 3.5 200 0.8±0.10 *1, *2 UMK107 B7333[]AHT X7R 0.033μ ±10, ±20 3.5 200 0.8±0.10 *1, *2 UMK107 B7473[]AHT X7R 0.047μ ±10, ±20 3.5 200 0.8±0.10 *1, *2 UMK107 B7683[]AHT X7R 0.068μ ±10, ±20 3.5 150 0.8±0.10 *1, *2 UMK107 B7104[]AHT X7R 0.1μ ±10, ±20 3.5 200 0.8±0.10 *1, *2 UMK107 C7224[]AHTE X7S 0.22μ ±10, ±20 3.5 150 0.8±0.10 *1, *2 GMK107 B7473[]AHT X7R 0.047μ ±10, ±20 3.5 200 0.8±0.10 *1, *2 GMK107 B7104[]AHT X7R 0.1μ ±10, ±20 3.5 150 0.8±0.10 *1, *2 C GMK107 B7224[]AHT 35 X7R 0.22μ ±10, ±20 10 150 0.8±0.10 *1, *2 E GMK107 B7474[]AHT X7R 0.47μ ±10, ±20 10 150 0.8±0.10 *1, *2 R GMK107AB7105[]AHT X7R 1μ ±10, ±20 10 150 0.8+0.15/-0.05 *1, *2 A TMK107 B7223[]AHT X7R 0.022μ ±10, ±20 2.5 200 0.8±0.10 *1, *2 M TMK107 B7473[]AHT X7R 0.047μ ±10, ±20 3.5 200 0.8±0.10 *1, *2 IC TTMMKK110077 BB77120244[[]]AAHHTT 25 XX77RR 0.02.21μμ ±±1100,, ±±2200 31.05 115500 00..88±±00..1100 **11,, **22 C TMK107 B7474[]AHT X7R 0.47μ ±10, ±20 10 150 0.8±0.10 *1, *2 A TMK107AB7105[]AHT X7R 1μ ±10, ±20 10 150 0.8+0.15/-0.05 *1, *2 P EMK107 B7473[]AHT X7R 0.047μ ±10, ±20 3.5 200 0.8±0.10 *1, *2 A EMK107 B7104[]AHT X7R 0.1μ ±10, ±20 3.5 150 0.8±0.10 *1, *2 C EMK107 B7224[]AHT 16 X7R 0.22μ ±10, ±20 5 150 0.8±0.10 *1, *2 IT EMK107 B7474[]AHT X7R 0.47μ ±10, ±20 10 150 0.8±0.10 *1, *2 O EMK107 B7105[]AHT X7R 1μ ±10, ±20 10 150 0.8±0.10 *1, *2 R LMK107 B7224[]AHT X7R 0.22μ ±10, ±20 5 150 0.8±0.10 *1, *2 S LMK107 B7474[]AHT 10 X7R 0.47μ ±10, ±20 3.5 150 0.8±0.10 *1, *2 LMK107 B7105[]AHT X7R 1μ ±10, ±20 10 150 0.8±0.10 *1, *2 LMK107BD7225[]AHT X7T 2.2μ ±10, ±20 10 200 0.8+0.20/-0 *1, *2 JMK107 B7105[]AHT X7R 1μ ±10, ±20 10 150 0.8±0.10 *1, *2 6.3 JMK107 B7225[]AHTR X7R 2.2μ ±10, ±20 10 150 0.8±0.10 *1, *2 ●212TYPE　(Dimension:2.0×1.25mm　JIS:2012　EIA:0805） 【Temperature Characteristic BJ : X5R（－55～＋85℃）】　1.25mm thickness（G） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance toClaepraanccitea n[c％e] t a[％nδ] Rated vHoTltLaTge x ％ Thickness*3 [mm] Note UMK212 BJ104[]GHT X5R 0.1μ ±10, ±20 3.5 200 1.25±0.10 *1, *2 UMK212 BJ224[]GHT X5R 0.22μ ±10, ±20 3.5 200 1.25±0.10 *1, *2 50 UMK212 BJ474[]GHT X5R 0.47μ ±10, ±20 3.5 150 1.25±0.10 *1, *2 UMK212 BJ105[]GHT X5R 1μ ±10, ±20 5 150 1.25±0.10 *1, *2 GMK212 BJ104[]GHT X5R 0.1μ ±10, ±20 3.5 200 1.25±0.10 *1, *2 GMK212 BJ224[]GHT X5R 0.22μ ±10, ±20 3.5 150 1.25±0.10 *1, *2 GMK212 BJ474[]GHT 35 X5R 0.47μ ±10, ±20 3.5 150 1.25±0.10 *1, *2 GMK212 BJ105[]GHT X5R 1μ ±10, ±20 5 150 1.25±0.10 *1, *2 GMK212BBJ225[]GHT X5R 2.2μ ±10, ±20 10 150 1.25+0.20/-0 *1, *2 TMK212 BJ104[]GHT X5R 0.1μ ±10, ±20 3.5 200 1.25±0.10 *1, *2 TMK212 BJ224[]GHT X5R 0.22μ ±10, ±20 3.5 150 1.25±0.10 *1, *2 TMK212 BJ474[]GHT X5R 0.47μ ±10, ±20 3.5 200 1.25±0.10 *1, *2 TMK212 BJ105[]GHT 25 X5R 1μ ±10, ±20 3.5 150 1.25±0.10 *1, *2 TMK212 BJ225[]GHT X5R 2.2μ ±10, ±20 5 150 1.25±0.10 *1, *2 TMK212BBJ475[]GHT X5R 4.7μ ±10, ±20 10 150 1.25+0.20/-0 *1, *2 TMK212BBJ106[]GHT X5R 10μ ±10, ±20 10 150 1.25+0.20/-0 *1, *2 EMK212 BJ105[]GHT X5R 1μ ±10, ±20 3.5 150 1.25±0.10 *1, *2 EMK212 BJ225[]GHT X5R 2.2μ ±10, ±20 5 150 1.25±0.10 *1, *2 16 EMK212ABJ475[]GHT X5R 4.7μ ±10, ±20 10 150 1.25+0.15/-0.05 *1, *2 EMK212BBJ106[]GHT X5R 10μ ±10, ±20 10 150 1.25+0.20/-0 *1, *2 LMK212 BJ225[]GHT X5R 2.2μ ±10, ±20 5 200 1.25±0.10 *1, *2 LMK212ABJ475[]GHT 10 X5R 4.7μ ±10, ±20 10 150 1.25+0.15/-0.05 *1, *2 LMK212ABJ106[]GHT X5R 10μ ±10, ±20 10 150 1.25+0.15/-0.05 *1, *2 JMK212ABJ475[]GHT X5R 4.7μ ±10, ±20 5 200 1.25+0.15/-0.05 *1, *2 JMK212ABJ106[]GHT 6.3 X5R 10μ ±10, ±20 10 150 1.25+0.15/-0.05 *1, *2 JMK212BBJ226MGHT X5R 22μ ±20 10 150 1.25+0.20/-0 *1, *2 AMK212ABJ226MGHT X5R 22μ ±20 10 150 1.25+0.15/-0.05 *1, *2 4 AMK212BBJ476MGHT X5R 47μ ±20 10 150 1.25+0.20/-0 *1, *2 【Temperature Characteristic BJ : X5R（－55～＋85℃）】　0.85mm thickness（D） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance toClaepraanccitea n[c％e] t a[％nδ] Rated vHoTltLaTge x ％ Thickness*3 [mm] Note EMK212 BJ105[]DHT X5R 1μ ±10, ±20 5 200 0.85±0.10 *1, *2 EMK212ABJ225[]DHT 16 X5R 2.2μ ±10, ±20 5 150 0.85±0.10 *1, *2 EMK212BBJ475[]DHT X5R 4.7μ ±10, ±20 10 150 0.85±0.10 *1, *2 hq_c_mlcc_e-E07R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 24 19

■PART NUMBER 【Temperature Characteristic B7 : X7R（－55～＋125℃）】　1.25mm thickness（G） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance toClaepraanccitea n[c％e] t a[％nδ] Rated vHoTltLaTge x ％ Thickness*3 [mm] Note UMK212 B7103[]GHT X7R 0.01μ ±10, ±20 3.5 200 1.25±0.10 *1, *2 UMK212 B7153[]GHT X7R 0.015μ ±10, ±20 2.5 200 1.25±0.10 *1, *2 UMK212 B7223[]GHT X7R 0.022μ ±10, ±20 3.5 200 1.25±0.10 *1, *2 UMK212 B7333[]GHT X7R 0.033μ ±10, ±20 3.5 200 1.25±0.10 *1, *2 UMK212 B7473[]GHT X7R 0.047μ ±10, ±20 3.5 200 1.25±0.10 *1, *2 50 UMK212 B7683[]GHT X7R 0.068μ ±10, ±20 3.5 200 1.25±0.10 *1, *2 UMK212 B7104[]GHT X7R 0.1μ ±10, ±20 3.5 200 1.25±0.10 *1, *2 UMK212 B7224[]GHT X7R 0.22μ ±10, ±20 3.5 150 1.25±0.10 *1, *2 UMK212 C7474[]GHTE X7S 0.47μ ±10, ±20 3.5 150 1.25±0.10 *1, *2 UMK212 B7105[]GHT X7R 1μ ±10, ±20 10 150 1.25±0.10 *1, *2 GMK212 B7224[]GHT X7R 0.22μ ±10, ±20 3.5 150 1.25±0.10 *1, *2 35 GMK212 B7105[]GHT X7R 1μ ±10, ±20 10 150 1.25±0.10 *1, *2 TMK212 B7224[]GHT X7R 0.22μ ±10, ±20 3.5 150 1.25±0.10 *1, *2 TMK212 B7334[]GHT X7R 0.33μ ±10, ±20 3.5 200 1.25±0.10 *1, *2 TMK212 B7474[]GHT 25 X7R 0.47μ ±10, ±20 3.5 150 1.25±0.10 *1, *2 TMK212 B7105[]GHTR X7R 1μ ±10, ±20 10 150 1.25±0.10 *1, *2 TMK212 B7225[]GHT X7R 2.2μ ±10, ±20 10 150 1.25±0.10 *1, *2 C EMK212 B7224[]GHT X7R 0.22μ ±10, ±20 3.5 200 1.25±0.10 *1, *2 E EMK212 B7334[]GHT X7R 0.33μ ±10, ±20 3.5 200 1.25±0.10 *1, *2 R EMK212 B7474[]GHT X7R 0.47μ ±10, ±20 3.5 200 1.25±0.10 *1, *2 A 16 EMK212 B7105[]GHTR X7R 1μ ±10, ±20 10 150 1.25±0.10 *1, *2 M EEMMKK221122 ABB77242755[[]]GGHHTT XX77RR 42..72μμ ±±1100,, ±±2200 1100 115500 1.215.+205.±150/.-100.05 **11,, **22 IC LMK212 B7105[]GHTR X7R 1μ ±10, ±20 10 150 1.25±0.10 *1, *2 C LMK212 B7225[]GHT 10 X7R 2.2μ ±10, ±20 10 150 1.25±0.10 *1, *2 A LMK212 B7475[]GHT X7R 4.7μ ±10, ±20 10 150 1.25±0.10 *1, *2 P JMK212 B7475[]GHT X7R 4.7μ ±10, ±20 10 150 1.25±0.10 *1, *2 A JMK212AB7106[]GHT 6.3 X7R 10μ ±10, ±20 10 150 1.25+0.15/-0.05 *1, *2 C IT O ●316TYPE (Dimension:3.2×1.6mm　JIS:3216　EIA:1206） R 【Temperature Characteristic BJ : X5R（－55～＋85℃）】　1.6mm thickness（L） S Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance toClaepraanccitea n[c％e] t a[％nδ] Rated vHoTltLaTge x ％ Thickness*3 [mm] Note UMK316 BJ474[]LHT X5R 0.47μ ±10, ±20 3.5 200 1.6±0.20 *1, *2 UMK316 BJ105[]LHT X5R 1μ ±10, ±20 3.5 200 1.6±0.20 *1, *2 50 UMK316 BJ225[]LHT X5R 2.2μ ±10, ±20 10 150 1.6±0.20 *1, *2 UMK316ABJ475[]LHT X5R 4.7μ ±10, ±20 10 150 1.6±0.20 *1, *2 GMK316 BJ105[]LHT X5R 1μ ±10, ±20 3.5 200 1.6±0.20 *1, *2 GMK316 BJ225[]LHT X5R 2.2μ ±10, ±20 10 150 1.6±0.20 *1, *2 35 GMK316 BJ475[]LHT X5R 4.7μ ±10, ±20 10 150 1.6±0.20 *1, *2 GMK316BBJ106[]LHT X5R 10μ ±10, ±20 10 150 1.6±0.30 *1, *2 TMK316 BJ225[]LHT X5R 2.2μ ±10, ±20 3.5 200 1.6±0.20 *1, *2 TMK316 BJ475[]LHT 25 X5R 4.7μ ±10, ±20 5 150 1.6±0.20 *1, *2 TMK316 BJ106[]LHT X5R 10μ ±10, ±20 5 150 1.6±0.20 *1, *2 EMK316 BJ225[]LHT X5R 2.2μ ±10, ±20 3.5 200 1.6±0.20 *1, *2 EMK316 BJ475[]LHT X5R 4.7μ ±10, ±20 5 150 1.6±0.20 *1, *2 16 EMK316 BJ106[]LHT X5R 10μ ±10, ±20 5 150 1.6±0.20 *1, *2 EMK316BBJ226MLHT X5R 22μ ±20 10 150 1.6±0.30 *1, *2 LMK316 BJ475[]LHT X5R 4.7μ ±10, ±20 5 150 1.6±0.20 *1, *2 LMK316 BJ106[]LHT 10 X5R 10μ ±10, ±20 5 150 1.6±0.20 *1, *2 LMK316ABJ226[]ＬHT X5R 22μ ±10, ±20 10 150 1.6±0.20 *1, *2 JMK316 BJ106[]LHT X5R 10μ ±10, ±20 5 200 1.6±0.20 *1, *2 JMK316ABJ226[]LHT X5R 22μ ±10, ±20 10 150 1.6±0.20 *1, *2 6.3 JMK316ABJ476MLHT X5R 47μ ±20 10 150 1.6±0.20 *1, *2 JMK316BBJ107MLHT X5R 100μ ±20 10 150 1.6±0.30 *2 AMK316ABJ107MLHT 4 X5R 100μ ±20 10 150 1.6±0.20 *2 hq_c_mlcc_e-E07R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 19 25

■PART NUMBER 【Temperature Characteristic B7 : X7R（－55～＋125℃）, C7 : X7S（－55～＋125℃）】　1.6mm thickness（L） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance toClaepraanccitea n[c％e] t a[％nδ] Rated vHoTltLaTge x ％ Thickness*3 [mm] Note UMK316 B7473[]LHT X7R 0.047μ ±10, ±20 3.5 200 1.6±0.20 *1, *2 UMK316 B7683[]LHT X7R 0.068μ ±10, ±20 2.5 200 1.6±0.20 *1, *2 UMK316 B7104[]LHT X7R 0.1μ ±10, ±20 3.5 200 1.6±0.20 *1, *2 UMK316 B7154[]LHT X7R 0.15μ ±10, ±20 3.5 200 1.6±0.20 *1, *2 UMK316 B7224[]LHT X7R 0.22μ ±10, ±20 3.5 200 1.6±0.20 *1, *2 50 UMK316 B7334[]LHT X7R 0.33μ ±10, ±20 3.5 200 1.6±0.20 *1, *2 UMK316 B7474[]LHT X7R 0.47μ ±10, ±20 3.5 200 1.6±0.20 *1, *2 UMK316 B7105[]LHT X7R 1μ ±10, ±20 3.5 200 1.6±0.20 *1, *2 UMK316 B7225[]LHT X7R 2.2μ ±10, ±20 10 150 1.6±0.20 *1, *2 UMK316AC7475[]LHTE X7S 4.7μ ±10, ±20 2.5 150 1.6±0.20 *1, *2 GMK316 B7105[]LHT X7R 1μ ±10, ±20 3.5 200 1.6±0.20 *1, *2 GMK316 B7225[]LHT 35 X7R 2.2μ ±10, ±20 10 150 1.6±0.20 *1, *2 GMK316AB7475[]LHT X7R 4.7μ ±10, ±20 10 150 1.6±0.20 *1, *2 TMK316 B7105[]LHT X7R 1μ ±10, ±20 3.5 200 1.6±0.20 *1, *2 TMK316 B7225[]LHT X7R 2.2μ ±10, ±20 3.5 200 1.6±0.20 *1, *2 25 TMK316AB7475[]LHT X7R 4.7μ ±10, ±20 10 150 1.6±0.20 *1, *2 C TMK316AB7106[]LHT X7R 10μ ±10, ±20 10 150 1.6±0.20 *1, *2 E EMK316 B7225[]LHT X7R 2.2μ ±10, ±20 3.5 200 1.6±0.20 *1, *2 R EMK316AB7475[]LHT 16 X7R 4.7μ ±10, ±20 10 150 1.6±0.20 *1, *2 A EMK316AB7106[]LHT X7R 10μ ±10, ±20 10 150 1.6±0.20 *1, *2 M LMK316 B7475[]LHT 10 X7R 4.7μ ±10, ±20 5 150 1.6±0.20 *1, *2 IC JLMMKK331166AABB77110066[[]]LLHHTT XX77RR 1100μμ ±±1100,, ±±2200 1100 115500 11..66±±00..2200 **11,, **22 C JMK316AB7226[]LHT 6.3 X7R 22μ ±10, ±20 10 150 1.6±0.20 *1, *2 A AMK316AB7226[]LHT 4 X7R 22μ ±10, ±20 10 150 1.6±0.20 *1, *2 P AMK316AC7476MLHT X7S 47μ ±20 10 150 1.6±0.20 *1, *2 A C IT ●325TYPE (Dimension:3.2×2.5mm　JIS:3225　EIA:1210） O 【Temperature Characteristic BJ : X5R（－55～＋85℃）】　2.5mm thickness（M） R S Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance toClaepraanccitea n[c％e] t a[％nδ] Rated vHoTltLaTge x ％ Thickness*3 [mm] Note UMK325 BJ106[]MHP 50 X5R 10μ ±10, ±20 5 150 2.5±0.20 *1, *2 GMK325 BJ106[]MHP 35 X5R 10μ ±10, ±20 5 150 2.5±0.20 *1, *2 TMK325 BJ106[]MHP 25 X5R 10μ ±10, ±20 5 150 2.5±0.20 *1, *2 EMK325 BJ226[]MHP X5R 22μ ±10, ±20 5 150 2.5±0.20 *1, *2 16 EMK325ABJ476[]MHP X5R 47μ ±10, ±20 10 150 2.5±0.30 *1, *2 LMK325 BJ226[]MHP X5R 22μ ±10, ±20 5 150 2.5±0.20 *1, *2 LMK325 BJ476[]MHP 10 X5R 47μ ±10, ±20 10 150 2.5±0.20 *1, *2 LMK325ABJ107MMHP X5R 100μ ±20 10 150 2.5±0.30 *2 JMK325 BJ476[]MHP X5R 47μ ±10, ±20 10 150 2.5±0.20 *1, *2 6.3 JMK325ABJ107MMHP X5R 100μ ±20 10 150 2.5±0.30 *2 AMK325ABJ107MMHP X5R 100μ ±20 10 150 2.5±0.30 *2 4 AMK325ABJ227MMHP X5R 220μ ±20 10 150 2.5±0.30 *2 【Temperature Characteristic BJ : X5R（－55～＋85℃）】　1.9mm thickness（N） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance toClaepraanccitea n[c％e] t a[％nδ] Rated vHoTltLaTge x ％ Thickness*3 [mm] Note UMK325 BJ475[]NHT 50 X5R 4.7μ ±10, ±20 10 150 1.9±0.20 *1, *2 GMK325 BJ225MNHT X5R 2.2μ ±20 3.5 200 1.9±0.20 *1, *2 35 GMK325 BJ475[]NHT X5R 4.7μ ±10, ±20 10 150 1.9±0.20 *1, *2 TMK325 BJ475[]NHT 25 X5R 4.7μ ±10, ±20 10 150 1.9±0.20 *1, *2 EMK325 BJ475MNHT X5R 4.7μ ±20 3.5 200 1.9±0.20 *1, *2 16 EMK325 BJ106[]NHT X5R 10μ ±10, ±20 5 150 1.9±0.20 *1, *2 【Temperature Characteristic C6 : X6S（－55～＋105℃）】　2.5mm thickness（M） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance toClaepraanccitea n[c％e] t a[％nδ] Rated vHoTltLaTge x ％ Thickness*3 [mm] Note JMK325AC6107MMHP 6.3 X6S 100μ ±20 10 150 2.5±0.30 *2 【Temperature Characteristic B7 : X7R（－55～＋125℃）】　2.5mm thickness（M） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance toClaepraanccitea n[c％e] t a[％nδ] Rated vHoTltLaTge x ％ Thickness*3 [mm] Note UMK325 B7225[]MHP X7R 2.2μ ±10, ±20 3.5 200 2.5±0.20 *1, *2 UMK325 B7335[]MHP X7R 3.3μ ±10, ±20 3.5 200 2.5±0.20 *1, *2 50 UMK325 B7475[]MHP X7R 4.7μ ±10, ±20 5 150 2.5±0.20 *1, *2 UMK325AB7106[]MHP X7R 10μ ±10, ±20 10 150 2.5±0.30 *1, *2 GMK325AB7106[]MHP 35 X7R 10μ ±10, ±20 10 150 2.5±0.30 *1, *2 TMK325 B7335[]MHP X7R 3.3μ ±10, ±20 3.5 200 2.5±0.20 *1, *2 TMK325AB7106[]MHPR 25 X7R 10μ ±10, ±20 10 150 2.5±0.30 *1, *2 TMK325 B7226[]MHP X7R 22μ ±10, ±20 10 150 2.5±0.20 *1, *2 EMK325 B7226[]MHP 16 X7R 22μ ±10, ±20 10 150 2.5±0.20 *1, *2 LMK325 B7226[]MHP 10 X7R 22μ ±10, ±20 10 150 2.5±0.20 *1, *2 JMK325 B7226[]MHPR X7R 22μ ±10, ±20 10 150 2.5±0.20 *1, *2 6.3 JMK325 B7476[]MHPR X7R 47μ ±10, ±20 10 150 2.5±0.20 *1, *2 hq_c_mlcc_e-E07R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 26 19

■PART NUMBER 【Temperature Characteristic B7 : X7R（－55～＋125℃）】　1.9mm thickness（N） Part number 1 Part number 2 Rated[ Vv]oltage cThaermapceteraritsutrices Capa c[Fit]ance toClaepraanccitea n[c％e] t a[％nδ] Rated vHoTltLaTge x ％ Thickness*3 [mm] Note UMK325 B7105[]NHT 50 X7R 1μ ±10, ±20 3.5 200 1.9±0.20 *1, *2 GMK325 B7225[]NHT X7R 2.2μ ±10, ±20 3.5 200 1.9±0.20 *1, *2 35 GMK325 B7475[]NHTR X7R 4.7μ ±10, ±20 10 150 1.9±0.20 *1, *2 TMK325 B7475[]NHT 25 X7R 4.7μ ±10, ±20 10 150 1.9±0.20 *1, *2 EMK325 B7475[]NHT X7R 4.7μ ±10, ±20 3.5 150 1.9±0.20 *1, *2 16 EMK325 B7106[]NHTR X7R 10μ ±10, ±20 10 150 1.9±0.20 *1, *2 C E R A M IC C A P A C IT O R S hq_c_mlcc_e-E07R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 19 27

Multilayer Ceramic Capacitors ■PACKAGING ①Minimum Quantity ●Taped package Thickness Standard quantity [pcs] Type(EIA) mm code Paper tape Embossed tape □MK021(008004) 0.125 K － 50000 □VS021(008004) □MK042(01005) 0.2 C, D － 40000 □VS042(01005) 0.2 C □MK063(0201) 0.3 P,T 15000 － □WK105(0204) ※ 0.3 P 10000 － 0.13 H － 20000 0.18 E － 15000 □MK105(0402) 0.2 C 20000 － □MF105(0402) 0.3 P 15000 － 0.5 V 10000 － □VK105(0402) 0.5 W 10000 － □MK107(0603) 0.45 K 4000 － □WK107(0306) ※ 0.5 V － 4000 □MF107(0603) 0.8 A 4000 － □VS107(0603) 0.7 C 4000 － □MJ107(0603) 0.8 A 3000 3000 □MK212(0805) 0.45 K 4000 － □WK212(0508) ※ 0.85 D □MF212(0805) 1.25 G － 3000 □VS212(0805) 0.85 D 4000 － 0.85 D 4000 － □MJ212(0805) 1.25 G － 2000 0.85 D 4000 － □MK316(1206) 1.15 F － 3000 □MF316(1206) 1.6 L － 2000 1.15 F － 3000 □MJ316(1206) 1.6 L － 2000 0.85 D 1.15 F □MK325(1210) － 2000 1.9 N □MF325(1210) 2.0max. Y 2.5 M － 1000 1.9 N － 2000 □MJ325(1210) 2.5 M － 500(T), 1000(P) □MK432(1812) 2.5 M － 500 Note : ※ LW Reverse type. ②Taping material ※No bottom tape for pressed carrier tape ●Card board carrier tape ●Embossed tape Top tape Top tape Base tape Sprocket hole Sprocket hole Bottom tape Chip cavity Base tape Chip cavity ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_pack_e-E06R01

Chip filled Chip ※ LW Reverse type. ③Representative taping dimensions ●Paper Tape（8mm wide） ●Pressed carrier tape（ 2mm pitch） Unit：mm（inch） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） T A B 3.5±0.05(0.138±0.002) 8.0±0.30.315±0.012) ( T1 F 2.0±0.05 4.0±0.1 (0.079±0.002) (0.157±0.004) Chip Cavity Insertion Pitch Tape Thickness Type(EIA) Ａ Ｂ Ｆ Ｔ T1 □MK063(0201) 0.37 0.67 0.45max. 0.42max. □WK105(0204) ※ 2.0±0.05 □MK105(0402) （*1 C） 0.65 1.15 0.4max. 0.3max. □MK105(0402) （*1 P） 0.45max. 0.42max. Note *1 Thickness, C：0.2mm ,P：0.3mm. ※ LW Reverse type. Unit：mm ●Punched carrier tape （2mm pitch） Unit：mm（inch） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） T A B 3.5±0.05(0.138±0.002) 8.0±0.30.315±0.012) ( F 2.0±0.05 4.0±0.1 (0.079±0.002) (0.157±0.004) Chip Cavity Insertion Pitch Tape Thickness Type(EIA) Ａ Ｂ Ｆ Ｔ □MK105 (0402) □MF105 (0402) 0.65 1.15 2.0±0.05 0.8max. □VK105 (0402) Unit：mm ●Punched carrier tape （4mm pitch） Unit：mm（inch） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） T A B 3.5±0.050.138±0.002) 8.0±0.3315±0.012) ( 0. ( F 4.0±0.1 (0.157±0.004) 2.0±0.1 (0.079±0.004) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_pack_e-E06R01

Chip Cavity Insertion Pitch Tape Thickness Type(EIA) Ａ Ｂ Ｆ Ｔ □MK107(0603) □WK107(0306) ※ 1.0 1.8 1.1max. □MF107(0603) 4.0±0.1 □MK212(0805) 1.65 2.4 □WK212(0508) ※ 1.1max. □MK316(1206) 2.0 3.6 Note：Taping size might be different depending on the size of the product. ※ LW Reverse type. Unit：mm ●Embossed tape（4mm wide） Unit：mm（inch） φ0.8±0.04 0.9±0.05 Sprockethole (φ0.031±0.002) (0.035±0.002) A B 1.8±0.02(0.071±0.001) 4.0±0.050.157±0.002) ( F 1.0±0.02 2.0±0.04 (0.039±0.001) (0.079±0.002) Chip Cavity Insertion Pitch Tape Thickness Type(EIA) Ａ Ｂ Ｆ K T □MK021(008004) 0.135 0.27 □VS021(008004) 1.0±0.02 0.5max. 0.25max. □MK042(01005) 0.23 0.43 □VS042(01005) Unit：mm ●Embossed tape（8mm wide） Unit：mm（inch） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） A B 3.5±0.050.138±0.002) 8.0±0.3315±0.012) ( 0. ( F 4.0±0.1 (0.157±0.004) 2.0±0.1 (0.079±0.004) Chip Cavity Insertion Pitch Tape Thickness Type(EIA) Ａ Ｂ Ｆ K T □MK105(0402) 0.6 1.1 2.0±0.1 0.6max 0.2±0.1 □WK107(0306) ※ 1.0 1.8 1.3max. 0.25±0.1 □MK212(0805) 1.65 2.4 □MF212(0805) □MK316(1206) 4.0±0.1 2.0 3.6 3.4max. 0.6max. □MF316(1206) □MK325(1210) 2.8 3.6 □MF325(1210) Note： ※ LW Reverse type. Unit：mm ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_pack_e-E06R01

●Embossed tape（12mm wide） Unit：mm（inch） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） B A 5.5±0.050.217±0.002) 12.0±0.3472±0.012) ( 0. ( 4.0±0.1 2.0±0.1 (0.157±0.004) (0.079±0.004) F Chip Cavity Insertion Pitch Tape Thickness Type(EIA) Ａ Ｂ Ｆ K T □MK325(1210) 3.1 4.0 8.0±0.1 4.0max. 0.6max. □MK432(1812) 3.7 4.9 8.0±0.1 4.0max. 0.6max. Unit：mm ④Trailer and Leader Blank portion Chip cavity Blank portion Leader 160mm or more 100mm or more (6.3inches or more) (3.94inches or more) 400mm or more Direction of tape feed (15.7inches or more) ⑤Reel size t E C B A R D W A B C D E R φ178±2.0 φ50min. φ13.0±0.2 φ21.0±0.8 2.0±0.5 1.0 T W 4mm wide tape 1.5max. 5±1.0 8mm wide tape 2.5max. 10±1.5 12mm wide tape 2.5max. 14±1.5 Unit：mm ⑥Top Tape Strength The top tape requires a peel-off force of 0.1 to 0.7N in the direction of the arrow as illustrated below. Pull direction 0～20° Top tape Base tape ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_mlcc_pack_e-E06R01

Multilayer Ceramic Capacitors ■RELIABILITY DATA 1.Operating Temperature Range Temperature Standard －55 to ＋125℃ Compensating（Class1） High Frequency Type Specification Temperature Range B －25 to ＋85℃ BJ Specified X5R －55 to ＋85℃ Value B7 X7R －55 to ＋125℃ High Permittivity （Class2） C6 X6S －55 to ＋105℃ C7 X7S －55 to ＋125℃ D7 X7T －55 to ＋125℃ LD(※) X5R －55 to ＋85℃ Note: ※LD Low distortion high value multilayer ceramic capacitor 2. Storage Conditions Temperature Standard －55 to ＋125℃ Compensating（Class1） High Frequency Type Specification Temperature Range B －25 to ＋85℃ BJ Specified X5R －55 to ＋85℃ Value B7 X7R －55 to ＋125℃ High Permittivity （Class2） C6 X6S －55 to ＋105℃ C7 X7S －55 to ＋125℃ D7 X7T －55 to ＋125℃ LD(※) X5R －55 to ＋85℃ Note: ※LD Low distortion high value multilayer ceramic capacitor 3. Rated Voltage Temperature Standard 50VDC, 25VDC Specified Compensating（Class1） High Frequency Type 50VDC, 25VDC Value High Permittivity （Class2） 50VDC, 35VDC, 25VDC, 16VDC, 10VDC, 6.3VDC, 4VDC, 2.5VDC 4. Withstanding Voltage （Between terminals） Temperature Standard Specified Compensating（Class1） High Frequency Type No breakdown or damage Value High Permittivity （Class2） Class 1 Class 2 Test Applied voltage Rated volta×3 Rated voltage×2.5 Methods and Duration 1 to 5 sec. Remarks Charge/discharge current 50mA max. 5. Insulation Resistance Temperature Standard 10000 MΩ min. Specified Compensating（Class1） High Frequency Type Value C≦0.047μF : 10000 MΩ min. High Permittivity （Class2） Note 1 C＞0.047μF : 500MΩ・μF Test Applied voltage : Rated voltage Methods and Duration : 60±5 sec. Remarks Charge/discharge current : 50mA max. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_c_mlcc_reli_e-E06R01

6. Capacitance （Tolerance） C□ 0.2pF≦C≦5pF : ±0.25pF Standard U□ 0.2pF≦C≦10pF : ±0.5pF Temperature SL C＞10pF : ±5% or ±10% Specified Compensating（Class1） 0.3pF≦C≦2pF : ±0.1pF Value High Frequency Type CH C＞2pF : ±5% BJ, B7, C6, C7, D7, LD(※) : ±10% or ±20% High Permittivity （Class2） Note: ※LD Low distortion high value multilayer ceramic capacitor Class 1 Class 2 Standard High Frequency Type C≦10μF C＞10μF Test Preconditioning None Thermal treatment （at 150℃ for 1hr） Note 2 Methods and Measuring frequency 1ＭHz±10% 1kHz±10% 120±10Hz Remarks Measuring voltage Note 0.5 to 5Vrms 1±0.2Vrms 0.5±0.1rms Bias application one 7. Q or Dissipation Factor C＜30pF : Q≧400＋20C Temperature Standard C≧30pF : Q≧1000 （C：Nominal capacitance） Specified Compensating（Class1） Value High Frequency Type Refer to detailed specification High Permittivity （Class2） Note 1 BJ, B7, C6, C7, D7：2.5% max. Class 1 Class 2 Standard High Frequency Type C≦10μF C＞10μF Preconditioning None Thermal treatment （at 150℃ for 1hr） Note 2 Test Measuring frequey 1ＭHz±10% 1GHz 1ｋHz±10% 120±10Hz Methods and Measuring voltage Note 1 0.5 to 5Vrms 1±0.2Vrms 0.5±0.1Vrms Remarks Bias application None High Frequency Type Measuring equipment : HP4291A Measuring jig : HP16192A 8. Temperature Characteristic （Without voltage application） Temperature Characteristic ［ppm/℃］ Tolerance ［ppm/℃］ G : ±30 C□ : 0 CG,CH, CJ, CK H : ±60 Standard Temperature U□ : －750 UJ, UK J : ±120 Compensating（Class1） K : ±250 SL : ＋350 to －1000 Temperature Characteristic ［ppm/℃］ Tolerance ［ppm/℃］ High Frequency Type C□ : 0 CH H : ±60 Specified Capacitance Reference Value Specification Temperature Range change temperature B ±10% 20℃ －25 to ＋85℃ BJ X5R ±15% 25℃ －55 to ＋85℃ B7 X7R ±15% 25℃ －55 to ＋125℃ High Permittivity （Class2） C6 X6S ±22% 25℃ －55 to ＋105℃ C7 X7S ±22% 25℃ －55 to ＋125℃ D7 X7S ＋22/－33% 25℃ －55 to ＋125℃ LD(※) X5R ±15% 25℃ －55 to ＋85℃ Note : ※LD Low distortion high value multilayer ceramic capacitor Class 1 Capacitance at 20℃ and 85℃ shall be measured in thermal equilibrium, and the temperature characteristic shall be calculated from the following equation. （C －C ） 85 20 ×106（ppm/℃） C ×△T △T＝65 20 Test Class 2 Methods and Capacitance at each step shall be measured in thermal equilibrium, and the temperature characteristic shall be calculated from the following Remarks equation. Step B X5R、X7R、X6S、X7S、X7T 1 Minimum operating temperature 2 20℃ 25℃ 3 Maximum operating temperature ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_c_mlcc_reli_e-E06R01

（C－C） 2 ×100（%） C 2 C ：Capacitance in Step 1 or Step 3 C2 ：Capacitance in Step 2 9. Deflection Appearance : No abnormality Standard Temperature Capacitance change : Within ±5% or ±0.5 pF, whichever is larger. Compensating（Class1） Appearance : No abnormality Specified High Frequency Type Cpaitance change : Within±0.5 pF Value Appearance : No abnormality High Permittivity （Class2） Capacitance change : Within ±12.5%（BJ, B7, C6, C7, D7, LD(※)） Note: ※LD Low distortion high value multilayer ceramic capacitor Multilayer Ceramic Capacitors 042, 063, ※１105 Type The other types Board Glass epoxy-resin substrate Test Thickness 0.8mm 1.6mm Methods and Warp 1mm （Soft Termination type:3mm） Remarks Duration 10 sec. ※１：105 Type thickness, C： 0.2mm ,P： 0.3mm. Capacitance measurement shall be conducted with the board bent 10. Body Strength Temperature Standard － Specified Compensating（Class1） High Frequency Type No mechanical damage. Value High Permittivity （Class2） － High Frequency Type Applied force : 5N Test Duration : 10 sec. Methods and Remarks 11. Adhesive Strength of Terminal Electrodes Temperature Standard Specified Compensating（Class1） High Frequency Type No terminal separation or its indication. Value High Permittivity （Class2） Multilayer Ceramic Capacitors Test 042, 063 Type 105 Type or more Methods and Applied force 2N 5N Remarks Duration 30±5 sec. 12. Solderability Temperature Standard Specified Compensating（Class1） High Frequency Type At least 95% of terminal electrode is covered by new solder. Value High Permittivity （Class2） Eutectic solder Lead-free solder Test Solder type H60A or H63A Sn-3.0Ag-0.5Cu Methods and Solder temperature 230±5℃ 245±3℃ Remarks Duration 4±1 sec. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_c_mlcc_reli_e-E06R01

13. Resistance to Soldering Appearance : No abnormality Capacitance change : Within ±2.5% or ±0.25pF, whichever is larger. Standard Q : Initial value Insulation resistance : Initial value Temperature Withstanding voltage （between terminals） : No abnormality Compensating（Class1） Appearance : No abnormality Capacitancecange : Within ±2.5% Specified High Frequency Type Q : Initial value Value Insulation resistance : Initial value Withstanding voltage （between terminals） : No abnormality Appearance : No abormality Capactace change : Within ±7.5%（BJ, B7, C6, C7, D7, LD(※)） Dissipation factor : Initial value High Permittivity （Class2） Note 1 Insulation resistance : Initial value Withstanding voltage （between terminals）: No abnormality Note: ※LD Low distortion high value multilayer ceramic capacitor lss 1 042, 063 Type 105 Type Preconditioning None 80 to 100℃, 2 to 5 min. Preheating 150℃, 1 to 2 min. 150 to 200℃, 2 to 5 min. Solder temp. 270±5℃ Duration 3±0.5 sec. Test Recovery 6 to 24 hrs （Standard condition） Noe 5 Methods and Remarks Class 2 042、063 Type 105, 107, 212 Type 316, 325 Type Preconditioning Thermal treatment （at 150℃ for 1 hr） Note 2 80 to 100℃, 2 to 5 min. 80 to 100℃, 5 to 10 min. Preheating 150℃, 1 to 2 min. 150 to 200℃, 2 to 5 min. 150 to 200℃, 5 to 10 min. Solder temp. 270±5℃ Duration 3±0.5 sec. Recovery 24±2 hrs （Standard condition） Note 5 14. Temperature Cycle (Thermal Shock） Appearance : No abnormality Capacitance change : Within ±2.5% or ±0.25pF, whichever is larger. Standard Q : Initial value Insulation resistance : Initial value Temperature Withstanding voltage （between terminals） : No abnormality Compensating（Class1） Appearance : No abnormality Capacitance change : Within ±0.25pF Specified High Frequency Type Q : Initial value Value Insulation resistance : Initial value Withstanding voltage （between terminals） : No abnormality Appearance : No abnormality Capacitance change : Within ±7.5% （BJ, B7, C6, C7, D7, LD(※)） Dissipation factor : Initial value High Permittivity （Class2） Note 1 Insulation resistance : Initial value Withstanding voltage （between terminals） : No abnormality Note: ※LD Low distortion high value multilayer ceramic capacitor Class 1 Class 2 Thermal treatment （at 150℃ for 1 hr） Preconditioning None Note 2 Step Temperature（℃） Time（min.） Test 1 Minimum operating temperature 30±3 Methods and 1 cycle 2 Normal temperature 2 to 3 Remarks 3 Maximum operating temperature 30±3 4 Normal temperature 2 to 3 Number of cycles 5 times Recovery 6 to 24 hrs （Standard condition） Note 5 24±2 hrs （Standard condition） Note 5 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_c_mlcc_reli_e-E06R01

15. Humidity （Steady State） Appearance : No abnormality Capacitance change : Within ±5% or ±0.5pF, whichever is larger. Q : C＜10pF : Q≧200＋10C Standard 10≦C＜30pF : Q≧275＋2.5C Temperature C≧30pF:Q≧350（C：Nominal capacitance） Compensating（Class1） Insulation resistance : 1000 MΩ min. Specified Appearance : No abnormality Value High Frequency Type Capacitance change : Within ±0.5pF, Insulation resistance : 1000 MΩ min. Appearance : No abnormality Capacitance change : Within ±12.5% （BJ, B7, C6, C7, D7, LD(※)） High Permittivity （Class2） Note 1 Dissipation factor : 5.0% max.（BJ, B7, C6, C7, D7, LD(※)） Insulation resistance : 50 MΩμF or 1000 MΩ whichever is smaller. Note: ※LD Low distortion high value multilayer ceramic capacitor Class 1 Class 2 Standard High Frequency Type All items Test Preconditioning None Thermal treatment（ at 150℃ for 1 hr） Note 2 Methods and Temperature 40±2℃ 60±2℃ 40±2℃ Remarks Humidity 90 to 95%RH 90 to 95%RH Duration 500＋24/－0 hrs 500＋24/－0 hrs Recovery 6 to 24 hrs （Standard condition） Note 5 24±2 hrs （Standard condition） Note 5 16. Humidity Loading Appearance : No abnormality Capacitance change : Within ±7.5% or ±0.75pF, whichever is larger. Standard Q : C＜30pF：Q≧100＋10C/3 C≧30pF：Q≧200 （C：Nominal capacitance） Temperature Insulation resistance : 500 MΩ min. Compensating（Class1） Appearance : No abnormality Capacitance change : C≦2pF：Within ±0.4 pF Specified High Frequency Type C＞2pF：Within ±0.75 pF Value （C：Nominal capacitance） Insulation resistance : 500 MΩ min. Appearance : No abnormality Capacitance change : Within ±12.5% （BJ, B7, C6, C7, D7, LD(※)） High Permittivity （Class2） Note 1 Dissipation factor : 5.0% max. （BJ, B7, C6, C7, D7, LD(※)） Insulation resistance : 25 MΩμF or 500 MΩ, whichever is smaller. Note: ※LD Low distortion high value multilayer ceramic capacitor Class 1 Class 2 Standard High Frequency Type All items Preconditioning Voltage treatment None （Rated voltage are applied for 1 hour at 40℃） Note 3 Test Temperature 40±2℃ 60±2℃ 40±2℃ Methods and Humidity 90 to 95%RH 90 to 95%RH Remarks Duration 500＋24/－0 hrs 500＋24/－0 hrs Applied voltage Rated voltage Rated voltage Charge/discharge 50mA max. 50mA max. current Recovery 6 to 24 hrs （Standard condition） Note 5 24±2 hrs（Standard condition） Note 5 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_c_mlcc_reli_e-E06R01

17. High Temperature Loading Appearance : No abnormality Capacitance change : Within ±3% or ±0.3pF, whichever is larger. Q : C＜10pF： Q≧200＋10C Standard 10≦C＜30pF：Q≧275＋2.5C Temperature C≧30pF： Q≧350（C：Nominal capacitance） Compensating（Class1） Insulation resistance : 1000 MΩ min. Specified Appearance : No abnormality Value High Frequency Type Capacitance change : Within ±3% or ±0.3pF, whichever is larger. Insulation resistance : 1000 MΩ min. Appearance : No abnormality Capacitance change : Within ±12.5% （BJ, B7, C6, C7, D7, LD(※)） High Permittivity （Class2） Note 1 Dissipation factor : 5.0% max.（BJ, B7, C6, C7, D7, LD(※)） Insulation resistance : 50 MΩμF or 1000 MΩ, whichever is smaller. Note: ※LD Low distortion high value multilayer ceramic capacitor Class 1 Class 2 Standard High Frequency Type BJ, LD(※) C6 B7, C7, D7 Voltage treatment（Twice the rated voltage shall be applied for Preconditioning None 1 hour at 85℃, 105℃ or 125℃） Note 3, 4 Temperature Maximum operating temperature Maximum operating temperature Test Duration 1000＋48/－0 hrs 1000＋48/－0 hrs Methods and Applied voltage Rated voltage×2 Rated voltage×2 Note 4 Remarks Charge/discharge 50mA max. 50mA max. current Recovery 6 to 24hr （Standard condition） Note 5 24±2 hrs （Standard condition） Note 5 Note: ※LD Low distortion high value multilayer ceramic capacitor Note 1 The figures indicate typical specifications. Please refer to individual specifications in detail. Note 2 Thermal treatment : Initial value shall be measured after test sample is heat-treated at 150＋0/－10℃ for an hour and kept at room temperature for 24±2hours. Note 3 Voltage treatment : Initial value shall be measured after test sample is voltage-treated for an hour at both the temperature and voltage specified in the test conditions, and kept at room temperature for 24±2hours. Note 4 150% of rated voltage is applicable to some items. Please refer to their specifications for further information. Note 5 Standard condition: Temperature: 5 to 35℃, Relative humidity: 45 to 85 % RH, Air pressure: 86 to 106kPa When there are questions concerning measurement results, in order to provide correlation data, the test shall be conducted under the following condition. Temperature: 20±2℃, Relative humidity: 60 to 70 % RH, Air pressure: 86 to 106kPa Unless otherwise specified, all the tests are conducted under the "standard condition". ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_c_mlcc_reli_e-E06R01

Precautions on the use of Multilayer Ceramic Capacitors ■PRECAUTIONS 1. Circuit Design ◆Verification of operating environment, electrical rating and performance 1. A malfunction of equipment in fields such as medical, aerospace, nuclear control, etc. may cause serious harm to human life or have severe social ramifications. Therefore, any capacitors to be used in such equipment may require higher safety and reliability, and shall be clearly differentiated from them used in general purpose applications. Precautions ◆Operating Voltage （Verification of Rated voltage） 1. The operating voltage for capacitors must always be their rated voltage or less. If an AC voltage is loaded on a DC voltage, the sum of the two peak voltages shall be the rated voltage or less. For a circuit where an AC or a pulse voltage may be used, the sum of their peak voltages shall also be the rated voltage or less. 2. Even if an applied voltage is the rated voltage or less reliability of capacitors may be deteriorated in case that either a high frequency AC voltage or a pulse voltage having rapid rise time is used in a circuit. 2. PCB Design ◆Pattern configurations （Design of Land-patterns） 1. When capacitors are mounted on PCBs, the amount of solder used （size of fillet） can directly affect the capacitor performance. Therefore, the following items must be carefully considered in the design of land patterns: （1）Excessive solder applied can cause mechanical stresses which lead to chip breaking or cracking. Therefore, please consider appropriate land-patterns for proper amount of solder. Precautions （2）When more than one component are jointly soldered onto the same land, each component's soldering point shall be separated by solder-resist. ◆Pattern configurations （Capacitor layout on PCBs） After capacitors are mounted on boards, they can be subjected to mechanical stresses in subsequent manufacturing processes （PCB cutting, board inspection, mounting of additional parts, assembly into the chassis, wave soldering of the boards, etc.）. For this reason, land pattern configurations and positions of capacitors shall be carefully considered to minimize stresses. ◆Pattern configurations （Design of Land-patterns） The following diagrams and tables show some examples of recommended land patterns to prevent excessive solder amounts. （1）Recommended land dimensions for typical chip capacitors ●Multilayer Ceramic Capacitors : Recommended land dimensions Land patterns for PCBs （unit: mm） Land pattern Wave-soldering Chip capacitor Solder-resist Type 107 212 316 325 L 1.6 2.0 3.2 3.2 Size C W 0.8 1.25 1.6 2.5 A 0.8 to 1.0 1.0 to 1.4 1.8 to 2.5 1.8 to 2.5 B 0.5 to 0.8 0.8 to 1.5 0.8 to 1.7 0.8 to 1.7 B A B C 0.6 to 0.8 0.9 to 1.2 1.2 to 1.6 1.8 to 2.5 Chip capacitor W L Technical Reflow-soldering considerations Type 042 063 105 107 212 316 325 432 L 0.4 0.6 1.0 1.6 2.0 3.2 3.2 4.5 Size W 0.2 0.3 0.5 0.8 1.25 1.6 2.5 3.2 A 0.15 to 0.25 0.20 to 0.30 0.45 to 0.55 0.8 to 1.0 0.8 to 1.2 1.8 to 2.5 1.8 to 2.5 2.5 to 3.5 B 0.15 to 0.20 0.20 to 0.30 0.40 to 0.50 0.6 to 0.8 0.8 to 1.2 1.0 to 1.5 1.0 to 1.5 1.5 to 1.8 C 0.15 to 0.30 0.25 to 0.40 0.45 to 0.55 0.6 to 0.8 0.9 to 1.6 1.2 to 2.0 1.8 to 3.2 2.3 to 3.5 Note：Recommended land size might be different according to the allowance of the size of the product. ●LWDC: Recommended land dimensions for reflow-soldering LWDC （unit: mm） Type 105 107 212 L 0.52 0.8 1.25 Size W W 1.0 1.6 2.0 A 0.18 to 0.22 0.25 to 0.3 0.5 to 0.7 B 0.2 to 0.25 0.3 to 0.4 0.4 to 0.5 C 0.9 to 1.1 1.5 to 1.7 1.9 to 2.1 L ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_c_mlcc_prec_e-E07R01

（2）Examples of good and bad solder application Items Not eommended Recommended Lead wire of component Solder-resist Mixed mounting of SMD and leaded components Chassis Solder (for grounding) Solder-resist Component placement close to the chassis Electrode pattern Lead wire of component Soldering iron Hand-soldering of leaded Solder-resist Components near mounted components Solder-resist Horizontal component placement ◆Pattern configurations （Capacitor layout on PCBs） 1-1. The following is examples of good and bad capacitor layouts ; capacitors shall be located to minimize any possible mechanical stresses from board warp or deflection. Items Not recommended Recommended Place the product at a right angle to the direction of the Deflection of board anticipated mechanical stress. 1-2. The amount of mechanical stresses given will vary depending on capacitor layout. Please refer to diagram below. E D Perforation C A B Slit Magnitude of stress A＞B＝C＞D＞E 1-3. When PCB is split, the amount of mechanical stress on the capacitors can vary according to the method used. The following methods are listed in order from least stressful to most stressful: push-back, slit, V-grooving, and perforation. Thus, please consider the PCB, split methods as well as chip location. 3. Mounting ◆Adjustment of mounting machine 1. When capacitors are mounted on PCB, excessive impact load shall not be imposed on them. 2. Maintenance and inspection of mounting machines shall be conducted periodically. ◆Selection of Adhesives Precautions 1. When chips are attached on PCBs with adhesives prior to soldering, it may cause capacitor characteristics degradation unless the following factors are appropriately checked : size of land patterns, type of adhesive, amount applied, hardening temperature and hardening period. Therefore, please contact us for further information. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_c_mlcc_prec_e-E07R01

◆Adjustment of mounting machine 1. When the bottom dead center of a pick-up nozzle is too low, excessive force is imposed on capacitors and causes damages. To avoid this, the following points shall be considerable. （1）The bottom dead center of the pick-up nozzle shall be adjusted to the surface level of PCB without the board deflection. （2）The pressure of nozzle shall be adjusted between 1 and 3 N static loads. （3）To reduce the amount of deflection of the board caused by impact of the pick-up nozzle, supporting pins or back-up pins shall be used on the other side of the PCB. The following diagrams show some typical examples of good and bad pick-up nozzle placement: Items Not recommended Recommended chipping Single-sided mounting or cracking supporting pins or back-up pins Double-sided mounting chipping supporting pins or cracking or back-up pins Technical 2. As the alignment pin is worn out, adjustment of the nozzle height can cause chipping or cracking of capacitors because of mechanical considerations impact on the capacitors. To avoid this, the monitoring of the width between the alignment pins in the stopped position, maintenance, check and replacement of the pin shall be conducted periodically. ◆Selection of Adhesives Some adhesives may cause IR deterioration. The different shrinkage percentage of between the adhesive and the capacitors may result in stresses on the capacitors and lead to cracking. Moreover, too little or too much adhesive applied to the board may adversely affect components. Therefore, the following precautions shall be noted in the application of adhesives. （1）Required adhesive characteristics a. The adhesive shall be strong enough to hold parts on the board during the mounting & solder process. b. The adhesive shall have sufficient strength at high temperatures. c. The adhesive shall have good coating and thickness consistency. d. The adhesive shall be used during its prescribed shelf life. e. The adhesive shall harden rapidly. f. The adhesive shall have corrosion resistance. g. The adhesive shall have excellent insulation characteristics. h. The adhesive shall have no emission of toxic gasses and no effect on the human body. （2）The recommended amount of adhesives is as follows; ［Recommended condition］ Amount adhesive After capacitor are bonded Figure 212/316 case sizes as examples a a a 0.3mm min b b 100 to 120μm c Adhesives shall not contact land c c 4. Soldering ◆Selection of Flux Since flux may have a significant effect on the performance of capacitors, it is necessary to verify the following conditions prior to use; （1）Flux used shall be less than or equal to 0.1 wt%（ in Cl equivalent） of halogenated content. Flux having a strong acidity content shall not be applied. （2）When shall capacitors are soldered on boards, the amount of flux applied shall be controlled at the optimum level. Precautions （3）When water-soluble flux is used, special care shall be taken to properly clean the boards. ◆Soldering Temperature, time, amount of solder, etc. shall be set in accordance with their recommended conditions. Sn-Zn solder paste can adversely affect MLCC reliability. Please contact us prior to usage of Sn-Zn solder. ◆Selection of Flux 1-1. When too much halogenated substance（Chlorine, etc.） content is used to activate flux, or highly acidic flux is used, it may lead to corrosion of terminal electrodes or degradation of insulation resistance on the surfaces of the capacitors. Technical 1-2. Flux is used to increase solderability in wave soldering. However if too much flux is applied, a large amount of flux gas may be emitted considerations and may adversely affect the solderability. To minimize the amount of flux applied, it is recommended to use a flux-bubbling system. 1-3. Since the residue of water-soluble flux is easily dissolved in moisture in the air, the residues on the surfaces of capacitors in high humidity conditions may cause a degradation of insulation resistance and reliability of the capacitors. Therefore, the cleaning methods and the capability of the machines used shall also be considered carefully when water-soluble flux is used. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_c_mlcc_prec_e-E07R01

◆Soldering ･ Ceramic chip capacitors are susceptible to thermal shock when exposed to rapid or concentrated heating or rapid cooling. ･ Therefore, the soldering must be conducted with great care so as to prevent malfunction of the components due to excessive thermal shock. ･ Preheating : Capacitors shall be preheated sufficiently, and the temperature difference between the capacitors and solder shall be within 100 to 130℃. ･ Cooling : The temperature difference between the capacitors and cleaning process shall not be greater than 100℃. ［Reflow soldering］ 【Recommended conditions for eutectic soldering】 【Recommended condition for Pb-free soldering】 300 300 Preheating 230℃ Peak Within 10sec. 260℃ Max. ℃） 200 60Msine.c . 6M0sine.c ℃） 200 Within 10sec. mperature（ 100 Slow cooling mperature（ 100 cSoololiwn g Te Te Preheating150℃ Heating above 60sec. Min. 230℃ 0 0 40sec. Max. 1/2T～1/3T Caution Capacitor ①The ideal condition is to have solder mass（fillet）controlled to 1/2 to 1/3 of the Solder T thickness of a capacitor. PC board ②Because excessive dwell times can adversely affect solderability, soldering duration shall be kept as close to recommended times as possible. ③Allowable number of reflow soldering : 2 times max. ［Wave soldering］ 【Recommended conditions for eutectic soldering】 【Recommended condition for Pb-free soldering】 300 300 230～250℃ Peak Preheating Within 3sec. 260℃ Max. ℃） 200 120sec. Min. ℃） 200 120sec. Min. Within 10sec. mperature（ 100 Slow cooling mperature（ 100 P15re0h℃ea ting cSoololiwng Te Te 0 0 Caution ①Wave soldering must not be applied to capacitors designated as for reflow soldering only. ②Allowable number of wave soldering : 1 times max. ［Hand soldering］ 【Recommended conditions for eutectic soldering】 【Recommended condition for Pb-free soldering】 400 400 400 230～280℃ Peak Peak Within 3sec. 350℃ Max. 280℃ Max. 300 300 Within 3sec. 300 Within 3sec. Temperature（℃） 210000 Slow cooling Temperature（℃） 210000 ⊿T P15re0h℃ea tMiningS. low cooling 温度（℃） 210000 ⊿T P15re0h℃ea tMinSinglo. w cooling Preheating 0 60sec. Min. 0 60sec. Min. 0 60sec. Min. ⊿T ⊿T 316type or less ⊿T≦150℃ 325type or more ⊿T≦130℃ Caution ①Use a 50W soldering iron with a maximum tip diameter of 1.0 mm. ②The soldering iron shall not directly touch capacitors. ③Allowable number of hand soldering : 1 times max. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_c_mlcc_prec_e-E07R01

5. Cleaning ◆Cleaning conditions 1. When PCBs are cleaned after capacitors mounting, please select the appropriate cleaning solution in accordance with the intended use Precautions of the cleaning. （e.g. to remove soldering flux or other materials from the production process.） 2. Cleaning condition shall be determined after it is verified by using actual cleaning machine that the cleaning process does not affect capacitor's characteristics. 1. The use of inappropriate cleaning solutions can cause foreign substances such as flux residue to adhere to capacitors or deteriorate their outer coating, resulting in a degradation of the capacitor's electrical properties （especially insulation resistance）. 2. Inappropriate cleaning conditions（ insufficient or excessive cleaning） may adversely affect the performance of the capacitors. In the case of ultrasonic cleaning, too much power output can cause excessive vibration of PCBs which may lead to the Technical cracking of capacitors or the soldered portion, or decrease the terminal electrodes' strength. Therefore, the following conditions shall considerations be carefully checked; Ultrasonic output : 20 W/ℓ or less Ultrasonic frequency : 40 kHz or less Ultrasonic washing period : 5 min. or less 6. Resin coating and mold 1. With some type of resins, decomposition gas or chemical reaction vapor may remain inside the resin during the hardening period or while left under normal storage conditions resulting in the deterioration of the capacitor's performance. Precautions 2. When a resin's hardening temperature is higher than capacitor's operating temperature, the stresses generated by the excessive heat may lead to damage or destruction of capacitors. The use of such resins, molding materials etc. is not recommended. 7. Handling ◆Splitting of PCB 1. When PCBs are split after components mounting, care shall be taken so as not to give any stresses of deflection or twisting to the board. 2. Board separation shall not be done manually, but by using the appropriate devices. Precautions ◆Mechanical considerations Be careful not to subject capacitors to excessive mechanical shocks. （1）If ceramic capacitors are dropped onto a floor or a hard surface, they shall not be used. （2）Please be careful that the mounted components do not come in contact with or bump against other boards or components. 8. Storage conditions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep packaging materials in good condition, care must be taken to control temperature and humidity in the storage area. Humidity should especially be kept as low as possible. ・Recommended conditions Ambient temperature : Below 30℃ Humidity : Below 70% RH Precautions The ambient temperature must be kept below 40℃. Even under ideal storage conditions, solderability of capacitor is deteriorated as time passes, so capacitors shall be used within 6 months from the time of delivery. ・Ceramic chip capacitors shall be kept where no chlorine or sulfur exists in the air. 2. The capacitance values of high dielectric constant capacitors will gradually decrease with the passage of time, so care shall be taken to design circuits . Even if capacitance value decreases as time passes, it will get back to the initial value by a heat treatment at 150℃ for 1hour. If capacitors are stored in a high temperature and humidity environment, it might rapidly cause poor solderability due to terminal oxidation and Technical quality loss of taping/packaging materials. For this reason, capacitors shall be used within 6 months from the time of delivery. If exceeding the considerations above period, please check solderability before using the capacitors. ※RCR-2335B（Safety Application Guide for fixed ceramic capacitors for use in electronic equipment）is published by JEITA. Please check the guide regarding precautions for deflection test, soldering by spot heat, and so on. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_c_mlcc_prec_e-E07R01