Product Specification 2 Gb/s RoHS Compliant Long-Wavelength Pluggable SFP Transceiver FTLF1419P1xCL PRODUCT FEATURES • Up to 2.125Gb/s bi-directional data links • Hot-pluggable SFP footprint • Built-in digital diagnostic functions • Uncooled 1310nm DFB laser transmitter • Duplex LC connector • RoHS compliant and Lead Free • No Rate Select input required for Fibre Channel 1x/2x Operation APPLICATIONS • Up to 55 km on 9/125µm SMF • 1.25Gb/s 1000Base-LX Ethernet • Metal enclosure, for lower EMI • Dual Rate 1.06 / 2.125 Gb/s Fibre • Single 3.3V power supply Channel • Low power dissipation <700mW typical • Extended operating temperature range: -10°C to 70°C Finisar’s FTLF1419P1xCL Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA)1. They simultaneously comply with Gigabit Ethernet as specified in IEEE Std 802.32, and 1x and 2x Fibre Channel as defined in FC-PI 13.03,4. The optical transceivers are compliant per the RoHS Directive 2011/65/EU. See Finisar Application Note AN-2038 for more details. Digital diagnostics functions are available via the 2-wire serial bus specified in the SFP MSA. PRODUCT SELECTION FTLF1419P1xCL x W Wide Extraction Bail B Narrow Extraction Bail  Finisar Corporation July 2015 Rev. B Page 1

FTLF1419P1xCL Pluggable SFP Product Specification I. Pin Descriptions Pin Symbol Name/Description Ref. 1 V Transmitter Ground (Common with Receiver Ground) 1 EET 2 T Transmitter Fault. Not supported. FAULT 3 T Transmitter Disable. Laser output disabled on high or open. 2 DIS 4 MOD_DEF(2) Module Definition 2. Data line for Serial ID. 3 5 MOD_DEF(1) Module Definition 1. Clock line for Serial ID. 3 6 MOD_DEF(0) Module Definition 0. Grounded within the module. 3 7 Rate Select No connection required 4 8 LOS Loss of Signal indication. Logic 0 indicates normal operation. 5 9 V Receiver Ground (Common with Transmitter Ground) 1 EER 10 V Receiver Ground (Common with Transmitter Ground) 1 EER 11 V Receiver Ground (Common with Transmitter Ground) 1 EER 12 RD- Receiver Inverted DATA out. AC Coupled 13 RD+ Receiver Non-inverted DATA out. AC Coupled 14 V Receiver Ground (Common with Transmitter Ground) 1 EER 15 V Receiver Power Supply CCR 16 V Transmitter Power Supply CCT 17 V Transmitter Ground (Common with Receiver Ground) 1 EET 18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. 19 TD- Transmitter Inverted DATA in. AC Coupled. 20 V Transmitter Ground (Common with Receiver Ground) 1 EET Notes: 1. Circuit ground is internally isolated from chassis ground. 2. Laser output disabled on T >2.0V or open, enabled on T <0.8V. DIS DIS 3. Should be pulled up with 4.7k - 10 kohms on host board to a voltage between 2.0V and 3.6V. MOD_DEF(0) pulls line low to indicate module is plugged in. 4. Finisar FTLFxx21xxxxx transceivers operate between OC-3 and OC-48, 1x and 2x Fibre Channel, and Gigabit Ethernet data rates and respective protocols without active control. Finisar FTLFxx19xxxxx transceivers operate at 1x and 2x Fibre Channel, and Gigabit Ethernet data rates and respective protocols without active control. 5. LOS is open collector output. Should be pulled up with 4.7k – 10 kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. VeeT 20 1 VeeT TD- 19 2 TXFault TD+ 18 3 TX Disable VeeT 17 4 MOD-DEF(2) VccT 16 Towards 5 MOD-DEF(1) Towards VccR 15 Bezel 6 MOD-DEF(0) ASIC VeeR 14 7 Rate Select RD+ 13 8 LOS RD- 12 9 VeeR VeeR 11 10 VeeR Pinout of Connector Block on Host Board  Finisar Corporation July 2015 Rev. B Page 2

FTLF1419P1xCL Pluggable SFP Product Specification II. Absolute Maximum Ratings Parameter Symbol Min Typ Max Unit Ref. Maximum Supply Voltage Vcc -0.5 4.5 V Storage Temperature T -40 85 °C S Case Operating Temperature T -10 70 °C OP Relative Humidity RH 0 85 % 1 III. Electrical Characteristics (T = -10 to 70 °C, V = 3.00 to 3.60 Volts) OP CC Parameter Symbol Min Typ Max Unit Ref. Supply Voltage Vcc 3.00 3.60 V Supply Current Icc 200 300 mA Transmitter Input differential impedance R 100 Ω 2 in Single ended data input swing Vin,pp 250 1200 mV Transmit Disable Voltage V Vcc – 1.3 Vcc V D Transmit Enable Voltage V Vee Vee+ 0.8 V 3 EN Transmit Disable Assert Time 10 us Receiver Single ended data output swing Vout,pp 300 400 800 mV 4 Data output rise time t 100 175 ps 5 r Data output fall time t 100 175 ps 5 f LOS Fault V Vcc – 0.5 Vcc V 6 LOS fault HOST LOS Normal V Vee Vee+0.5 V 6 LOS norm Power Supply Rejection PSR 100 mVpp 7 Deterministic Jitter Contribution RX ∆ DJ 51.7 ps 8 Total Jitter Contribution RX ∆ TJ 122.4 ps Notes: 1. Non condensing. 2. Connected directly to TX data input pins. AC coupled thereafter. 3. Or open circuit. 4. Into 100 ohm differential termination. 5. 20 – 80 % 6. LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 7. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network. 8. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and ∆ DJ.  Finisar Corporation July 2015 Rev. B Page 3

FTLF1419P1xCL Pluggable SFP Product Specification IV. Optical Characteristics (T = -10 to 70 °C, V = 3.00 to 3.60 Volts) OP CC Parameter Symbol Min Typ Max Unit Ref. Transmitter Output Opt. Power P 0 5 dBm 1 OUT Optical Wavelength λ 1275 1350 nm 2 Spectral Width (-20dB) σ 1 nm 2 Optical Modulation Amplitude OMA 174 µW 2,3 Sidemode Supression Ratio SSR 30 dB Optical Rise/Fall Time t/ t 160 ps 4 r f Relative Intensity Noise RIN -120 dB/Hz Optical Extinction Ratio ER 9 dB Deterministic Jitter Contribution TX ∆DJ 56.5 ps 5 Total Jitter Contribution TX ∆TJ 119 ps Receiver Average Rx Sensitivity @ 2.125 R -21 dBm 6, 7 SENS1 Gb/s (2X Fibre Channel) Average Rx Sensitivity @ 1.25 Gb/s R -22 dBm 6, 7 SENS2 (Gigabit Ethernet) Average Rx Sensitivity @ 1.06 Gb/s R -22 dBm 6, 7 SENS1 (1X Fibre Channel) Maximum Input Power P 0 dBm MAX Receiver Elec. 3 dB cutoff freq. 1500 MHz Optical Center Wavelength λ 1270 1600 nm C Return Loss 12 dB LOS De-Assert LOS -23 -19 dBm D LOS Assert LOS -30 -25 dBm A LOS Hysteresis 0.5 dB Notes: 1. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations. 2. Meets curves in FC-PI 13.0 Figures 18 and 19, which allow trade-off between wavelength, spectral width and OMA. 3. Equivalent extinction ratio specification for Fibre Channel. Allows smaller ER at higher average power. 4. Unfiltered, 20-80%. Complies with FC 1x and 2x eye mask when filtered. 5. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and ∆DJ. 6. Measured with conformance signals defined in FC-PI 13.0 specifications. 7. As measured with 9dB extinction ratio. Measured with a PRBS 27-1 test pattern.  Finisar Corporation July 2015 Rev. B Page 4

FTLF1419P1xCL Pluggable SFP Product Specification V. General Specifications Parameter Symbol Min Typ Max Units Ref. Data Rate BR 1062 2125 Mb/sec 1 Bit Error Rate BER 10-12 2 Max. Supported Link Length on L 52.5 km 3, 4 MAX1 9/125µm SMF @ 2X Fibre Channel Max. Supported Link Length on L 55 km 3, 4 MAX2 9/125µm SMF @ Gigabit Ethernet Notes: 1. Gigabit Ethernet and 1x/2x Fibre Channel compliant. 2. Tested with a PRBS 27-1 test pattern. 3. Dispersion limited per FC-PI Rev. 13 4. Attenuation of 0.40 dB/km is used for the link length calculations. Distances are indicative only. Please refer to the Optical Specifications in Table IV to calculate a more accurate link budget based on specific conditions in your application. VI. Environmental Specifications Finisar 1310nm SFP transceivers have an extended operating temperature range from –10°C to +70°C case temperature. Parameter Symbol Min Typ Max Units Ref. Case Operating Temperature T -10 70 °C op Storage Temperature T -40 85 °C sto VII. Regulatory Compliance Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TÜV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request.  Finisar Corporation July 2015 Rev. B Page 5

FTLF1419P1xCL Pluggable SFP Product Specification VIII. Digital Diagnostic Functions Finisar FTLF1419P1xCL SFP transceivers support the 2-wire serial communication protocol as defined in the SFP MSA3. The standard SFP serial ID provides access to identification information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information. Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range. The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification and the SFP Multi Source Agreement. The complete interface is described in Finisar Application Note AN- 2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. For more information, please see the SFP MSA documentation3 or Finisar Application Note AN-2030. Digital diagnostics for the FTLF1419P1xCL are externally calibrated by default. Please note that evaluation board FDB-1018 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface.  Finisar Corporation July 2015 Rev. B Page 6

FTLF1419P1xCL Pluggable SFP Product Specification IX. Mechanical Specifications Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA) 3. FTLF1419P1BCL  Finisar Corporation July 2015 Rev. B Page 7

FTLF1419P1xCL Pluggable SFP Product Specification FTLF1419P1WCL  Finisar Corporation July 2015 Rev. B Page 8

FTLF1419P1xCL Pluggable SFP Product Specification X. PCB Layout and Bezel Recommendations  Finisar Corporation July 2015 Rev. B Page 9

FTLF1419P1xCL Pluggable SFP Product Specification  Finisar Corporation July 2015 Rev. B Page 10

FTLF1419P1xCL Pluggable SFP Product Specification XI. References 1. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 2000. Documentation is currently available at Finisar upon request. 2. IEEE Std 802.3. IEEE Standards Department, 2002. 3. “Fibre Channel Draft Physical Interface Specification (FC-PI 13.0)”. American National Standard for Information Systems.(*) 4. “Fibre Channel Physical and Signaling Interface (FC-PH, FC-PH2, FC-PH3)”. American National Standard for Information Systems. 5. Directive 2011/65/EU of the European Council Parliament and of the Council, “on the restriction of the use of certain hazardous substances in electrical and electronic equipment”. Certain products may use one or more exemptions as allowed by the Directive. (*) FC-PI 13.0 does not specify a 1310nm DFB interface for extended reach applications. The FTLF1419P1xCL complies with this standard, except for the optical output power. See section IV for details. XII. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com  Finisar Corporation July 2015 Rev. B Page 11

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: F inisar: FTLF1419P1BCL