Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers will need to change in order to meet ON Semiconductor’s system requirements. Since the ON Semiconductor product management systems do not have the ability to manage part nomenclature that utilizes an underscore (_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please email any questions regarding the system integration to Fairchild_questions@onsemi.com. ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

F M S 6 1 August 2009 4 5 — FMS6145 L o w Low-Cost Five-Channel 4th-Order - C Standard Defi nition Video Filter Driver o s t F Features Description iv e ■ Five 4th-order 8MHz (SD) fi lters The FMS6145 Low-Cost Video Filter (LCVF) is intended -C ■ Drives single, AC- or DC-coupled, video loads (2V , 150Ω) to replace passive LC fi lters and drivers with a low-cost h pp a ■ Drives dual, AC- or DC-coupled, video loads (2V , 75Ω) integrated device. Five 4th-order fi lters provide improved n pp n ■ Transparent input clamping image quality compared to typical 2nd or 3rd-order e ■ AC- or DC-coupled inputs passive solutions. l 4 t ■ AC- or DC-coupled outputs The FMS6145 may be directly driven by a DC-coupled h - ■ DC-coupled outputs eliminate AC-coupling capacitors DAC output or an AC-coupled signal. Internal diode O r ■ 5V only clamps and bias circuitry may be used if AC-coupled d e ■ Robust 8kV ESD protection inputs are required (see Applications section for details). r S ■ Lead-free TSSOP-14 package The outputs can drive AC- or DC-coupled single (150Ω) or t a dual (75Ω) loads. DC coupling the outputs removes the n Applications d need for output coupling capacitors. The input DC levels a ■ Cable set-top boxes r are offset approximately +280mV at the output (see d ■ Satellite set-top boxes Applications section for details). D ■ DVD players e fi ■ HDTV n i t ■ Personal Video Recorders (PVR) i o ■ Video On Demand (VOD) n V i d e Functional Block Diagram o F i l t e IN1 Transparent Clamp 6dB OUT1 r D r i v IN2 Transparent Clamp 6dB OUT2 e r IN3 Transparent Clamp 6dB OUT3 IN4 Transparent Clamp 6dB OUT4 IN5 Transparent Clamp 6dB OUT5 8MHz, 4th order Ordering Information Operating Part Number Eco Status Package Packaging Method Temperature Range FMS6145MTC14X -40°C to +85°C RoHS TSSOP-14 Tape and Reel For Fairchild’s defi nition of Eco Status, please visit: http://www.fairchildsemi.com/company/green/rohs_green.html. © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FMS6145 • Rev. 2.0.6

F M Pin Confi guration S 6 1 4 IN1 1 14 OUT1 5 — IN2 2 FMS6145 13 OUT2 L 14-pin o IN3 3 TSSOP 12 OUT3 w - C VCC 4 11 GND o s IN4 5 10 OUT4 t F i IN5 6 9 OUT5 v e - NC 7 8 NC C h a n n e l 4 Pin Assignments t h - O Pin # Name Type Description r d 1 IN1 Input Video input, channel 1 e r 2 IN2 Input Video input, channel 2 S t a 3 IN3 Input Video input, channel 3 n d 4 V Input +5V supply, do not fl oat a CC r d 5 IN4 Input Video input, channel 4 D e 6 IN5 Input Video input, channel 5 fi n 7, 8 NC No Connect it i o 9 OUT5 Output Filtered video output, channel 5 n V 10 OUT4 Output Filtered video output, channel 4 i d e 11 GND Output Must be tied to ground, do not fl oat o F 12 OUT3 Output Filtered video output, channel 3 i l t 13 OUT2 Output Filtered video output, channel 2 e r D 14 OUT1 Output Filtered video output, channel 1 r i v e r © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FMS6145 • Rev. 2.0.6 2

F M Absolute Maximum Ratings S 6 The “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. The 1 4 device should not be operated at these limits. The parametric values defi ned in the Electrical Characteristics tables are 5 not guaranteed at the absolute maximum ratings. The “Recommended Operating Conditions” table defi nes the conditions — for actual device operation. Functional operation under any of these conditions is NOT implied. Performance and reliabi- L o lity are guaranteed only if recommended operating conditions are not exceeded. w - C Parameter Min. Max. Unit o s DC Supply Voltage -0.3 6 V t F Analog and Digital I/O -0.3 V + 0.3 V CC iv Output Channel - Any One Channel (Do Not Exceed) 50 mA e - C h a n n e l 4 Reliability Information t h - Symbol Parameter Min. Typ. Max. Unit O r d T Junction Temperature 150 °C J e r TSTSG Storage Temperature Range -65 +150 °C S t T Lead Temperature (Soldering, 10s) 300 °C a L n θJA Thermal Resistance, JEDEC Standard Multi-layer 90 °C/W da Test Boards, Still Air r d D e fi n i t Electrostatic Discharge Information io n Symbols Parameter Max. Unit V i d Human Body Model, JESD22-A114 4 e ESD kV o Charged Device Model, JESD22-C101 2 F i l t e r D r i v Recommended Operating Conditions e r Symbol Parameter Min. Typ. Max. Unit T Operating Temperature Range -40 +85 °C A V V Range +4.75 +5.0 +5.25 V CC CC © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FMS6145 • Rev. 2.0.6 3

F M DC Electrical Characteristics S 6 T = 25°C, V = 5V, R = 37.5Ω; all inputs are AC-coupled with 0.1μF; all outputs are AC coupled with 220μF into 1 A CC SOURCE 4 150Ω loads; unless otherwise noted. 5 — Symbol Parameter Conditions Min. Typ. Max. Units L I Supply Current(1) FMS6145 (No Load) 30 46 mA o CC w - VIN Video Input Voltage Range Referenced to GND if DC-coupled 1.4 Vpp C o PSRR Power Supply Rejection DC (All Channels) -50 dB s t F i v Notes: e - 1.100% tested at 25°C. C h a n n e AC Electrical Characteristics l 4 TA = 25°C, VIN = 1Vpp, VCC = 5V, RSOURCE = 37.5Ω; all inputs are AC coupled with 0.1μF; all outputs are th - AC-coupled with 220μF into 150Ω loads; unless otherwise noted. O r d Symbol Parameter Conditions Min. Typ. Max. Units e r AV Channel Gain(1) All Channels 6.0 6.2 6.4 dB S t f -1dB Bandwidth(1) All Channels 4.5 6.7 MHz a 1dB n f -3dB Bandwidth All Channels 7.9 MHz d c a r f Attenuation (Stopband Reject) All Channels at f = 27MHz 48 dB d SB D dG Differential Gain All Channels 0.3 % e fi dφ Differential Phase All Channels 0.6 ° n i t THD Output Distortion (All Channels) VOUT = 1.8Vpp, 1MHz 0.4 % io n XTALK Crosstalk (Channel-to-Channel) at 1MHz -60 dB V i All Channels, NTC-7 Weighting: 75 dB d SNR Signal-to-Noise Ratio 100kHz to 4.2MHz e o t Propagation Delay Delay from Input-to-Output, 4.5MHz 59 ns F pd i l t e r Notes: D 1.100% tested at 25°C. r i v e r © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FMS6145 • Rev. 2.0.6 4

F M Typical Performance Characteristics S 6 T = 25°C, V = 5V, R = 37.5Ω; all inputs AC coupled with 0.1μF; all outputs are AC coupled with 220μF into 150Ω 1 A CC SOURCE 4 loads; unless otherwise noted. 5 — L 5 50 o 0 2 40 w - B) -5 1 30 C d-10 o Gain (--1250 ns) 1200 1 st F ed -25 ay ( 0 iv maliz--3305 MRekfr F4r0e0qkuHenzc y 6GdaiBn Del--2100 e-C Nor-40 1 6.68MHz -1dB BW -30 ha -45 2 7.87MHz -3dB BW n -50 3 27MHz -48.66dB -40 1 = 8.2MHz (14.78ns) n -55 3 -50 e l 400kHz 5 10 15 20 25 30 400kHz 5 10 15 20 25 30 4 t Frequency (MHz) Frequency (MHz) h - O Figure 1. Frequency Response Figure 2. Group Delay vs. Frequency r d e r -60 0.2 S NTSC t -70 0.1 a n %) d e (dB) --8900 al Gain (-0.10 ard D Nois-100 enti-0.2 efi --111200 Differ--00..43 MMianx = = - 00..0331 nition -130 -0.5 ppMax = 0.34 V i 400kHz 1 2 3 4 5 6 1st 2nd 3rd 4th 5th 6th d e Frequency (MHz) o F Figure 3. Noise vs. Frequency Figure 4. Differential Gain il t e r D 1.0 r NTSC iv 0.8 e g) r e d 0.6 e ( s a 0.4 h P al 0.2 nti e er 0 Diff-0.2 MMianx = = 0 0.0.603 ppMax = 0.63 -0.4 1st 2nd 3rd 4th 5th 6th Figure 5. Differential Phase © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FMS6145 • Rev. 2.0.6 5

F M Typical Application Diagrams S 6 The following circuit may be used for direct DC-coupled drive by DACs with an output voltage range of 0V to 1.4V. 1 4 AC-coupled or DC-coupled outputs may be used with AC-coupled outputs, offering slightly lower power dissipation. 5 — L o DVD Player or STB +5V w 0.1 1.0 - μF μF C o ROUT 1 IN1 OUT1 14 75Ω 220μF 75Ω Video Cables R st F 75Ω iv 2 13 75Ω 220μF G e- GOUT IN2 OUT2 C FMS6145 75Ω h 3 14L TSSOP 12 75Ω 220μF B an BOUT IN3 OUT3 n 75Ω e l Video 4 11 4 SoC VCC GND th - 5 10 75Ω 220μF 75Ω Video Cables Y Or YOUT IN4 OUT4 d 75Ω e 6 9 75Ω 220μF C r S COUT IN5 OUT5 t 75Ω a n 7 8 d NC NC a r d DAC load resistors AC coupling caps D per SoC specifications. are optional. e fi n i t i o Figure 6. Typical Application Diagram n V i d e o F i l t e r D r i v e r © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FMS6145 • Rev. 2.0.6 6

F M Application Information S 6 Application Circuits 75Ω Video Cables LOAD2 1 (optional) 4 The FMS6145 Low Cost Video Filter (LCVF) provides 0.65V 75Ω 5 — 6dB gain from input to output. In addition, the input is L slightly offset to optimize the output driver performance. YIN Driver LOAD1 o The offset is held to the minimum required value to YOUT 75Ω Video Cables 75Ω w - decrease the standing DC-current into the load. Typical C o voltage levels are shown in the diagram below: Figure 8. Input Clamp Circuit s t F 1.0 -> 1.02V i I/O Confi gurations v e 0.65 -> 0.67V - For a DC-coupled DAC drive with DC-coupled outputs, C 0.3 -> 0.32V use the confi guration in Figure 9. h a 0.0 -> 0.02V VIN n n e 0V - 1.4V l 2.28V DVD or LCVF 75Ω 4 Driven by: STB Clamp th 1.58V DC-Coupled DAC Outputs SoC Inactive -O AC-Coupled and Clamped DAC r 0.88V Y, CV, R, G, B Output d 0.28V VOUT er S t There is a 280mV offset from the DC input level to the a n DC output level. VOUT = 2 * VIN + 280mV. d Figure 9. DC-Coupled Inputs and Outputs a r d 0.85V Alternatively, if the DAC’s average DC output level causes D the signal to exceed the range of 0V to 1.4V, it can be AC e 0.5V coupled as shown in FIgure 10. fi n i 0.15V t VIN 0V - 1.4V ion DVD or 0.1μ LCVF 75Ω V 1.98V STB Clamp i Driven by: d SoC Active e 1.28V AC-Coupled and Biased DAC o U, V, Pb, Pr, C Output F 0.58V i VOUT lte r D Figure 7. Typical Voltage Levels r Figure 10. AC-Coupled Inputs, iv The FMS6145 provides an internal diode clamp to sup- e DC-Coupled Outputs r port AC-coupled input signals. If the input signal does not go below ground, the input clamp does not operate. This When the FMS6145 is driven by an unknown external allows DAC outputs to directly drive the FMS6145 without source or a SCART switch with its own clamping circuitry, an AC coupling capacitor. When the input is AC coupled, the inputs should be AC coupled as shown in Figure 11. the diode clamp sets the sync tip (or lowest voltage) just below ground. The worst-case sync tip compression due 0V - 1.4V to the clamp cannot exceed 7mV. The input level set by External video 0.1μ LCVF 75Ω the clamp, combined with the internal DC offset, keeps Clamp source must the output within its acceptable range. Active be AC coupled For symmetric signals like Chroma, U, V, Pb, and Pr, the 75Ω average DC bias is fairly constant and the inputs can be AC coupled with the addition of a pull-up resistor to set the DC input voltage. DAC outputs can also drive these same signals without the AC coupling capacitor. A conceptual illustration of the input clamp circuit is shown in Figure 8. Figure 11. SCART with DC-Coupled Outputs © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FMS6145 • Rev. 2.0.6 7

F M The same method can be used for biased signals, with the External video S addition of a pull-up resistor to make sure the clamp never source must 0V - 1.4V 6 1 operates. The internal pull-down resistance is 800kΩ be AC coupled 0.1μ LCVF 75Ω 220μ 4 ±20%, so the external resistance should be 7.5MΩ to set CAlcatmivep 5 — the DC level to 500mV; as shown in Figure 12. L 75Ω o External video w source must 7.5MΩ -C be AC coupled 0.1μ LCVF 75Ω o Bias s Figure 15. Biased SCART with t Input F AC-Coupled Outputs i v 75Ω 500mV +/-350mV e Note: The video tilt or line time distortion is dominated by - C the AC-coupling capacitor. The value may need to be incre- h ased beyond 220μF to obtain satisfactory operation in a some applications. n n e Figure 12. Biased SCART with Power Dissipation l 4 DC-Coupled Outputs t The FMS6145 output drive confi guration must be considered h - The same circuits can be used with AC-coupled outputs if when calculating overall power dissipation. Care must be O desired. taken not to exceed the maximum die junction temperature. rd The following example can be used to calculate the e 0V - 1.4V FMS6146’s power dissipation and internal temperature rise. r S DVD or 0.1μ LCVF 75Ω 220μ T = T + P • q EQ. 1 ta STB Clamp j A d JA n SoC Active where: P = P + P + P and EQ. 2 d d CH1 CH2 CH3 a DAC r Output PCHx = VCC • ICH - (VO2/RL) EQ. 3 d D where: VO = 2VIN + 0.280V EQ. 4 e fi ICH = (ICC/3) + (VO/RL) EQ. 5 n i t V = RMS value of input signal i Figure 13. DC-Coupled Inputs, IN o n AC-Coupled Outputs ICC = 30mA V V = 5V id CC e 0V - 1.4V R = channel load resistance o DVD or 0.1μ LCVF 75Ω 220μ BoLard layout can also affect thermal characteristics. Refer Fi STB Clamp lt to the Layout Considerations section for details. e SoC Active r DAC The FMS6145 is specifi ed to operate with output currents D Output r typically less than 50mA, more than suffi cient for a dual i v (75Ω) video load. Internal amplifi ers are current limited to a e r maximum of 100mA and should withstand brief-duration short-circuit conditions; this capability is not guaranteed. Figure 14. AC-Coupled Inputs and Outputs © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FMS6145 • Rev. 2.0.6 8

F M S Layout Considerations Output Considerations 6 1 General layout and supply bypassing play major roles in The FMS6145 outputs are DC offset from the input by 4 5 high-frequency performance and thermal characteristics. 150mV. Therefore, VOUT = 2•VIN DC+150mV. This offset is — Fairchild offers a demonstration board, FMS6145DEMO, required to obtain optimal performance from the output dri- L to guide layout and aid device testing and characterizati- ver and is held at the minimum value to decrease the stan- o on. The FMS6145DEMO is a four-layer board with full ding DC current into the load. Since the FMS6145 has a 2x w - power and ground planes. Following this layout confi gu- (6dB) gain, the output is typically connected via a 75Ω- C o ration provides the optimum performance and thermal series back-matching resistor, followed by the 75Ω video s characteristics. For optimum results, follow the guidelines cable. Due to the inherent divide by two of this confi gurati- t F below as a basis for high-frequency layout: on, the blanking level at the load of the video signal is i v always less than 1V. When AC-coupling the output, ensure e - C that the coupling capacitor of choice passes the lowest ■ Include 1μF and 0.1μF ceramic bypass capacitors. h frequency content in the video signal and that line time dis- a n ■ Place the 1μF capacitor within 0.75 inches of the tortion (video tilt) is kept as low as possible. n power pin. e The selection of the coupling capacitor is a function of the l 4 ■ Place the 0.1μF capacitor within 0.1 inches of the subsequent circuit input impedance and the leakage cur- t h power pin. rent of the input being driven. To obtain the highest quality - O ■ For multi-layer boards, use a large ground plane to help output video signal, the series termination resistor must be r d dissipate heat. placed as close to the output pin as possible. This reduces e r ■ For two-layer boards, use a ground plane that extends the parasitic capacitance and inductance effect on the out- S put driver. The distance from the device pin to the series t beyond the device by at least 0.5 inches. a termination resistor should be no greater than 0.1 inches. n ■ Minimize all trace lengths to reduce series inductances. d a r d D e fi n i t i o n V i d e o F i l t e r D r i Figure 16. Distance from Device Pin to Series v e Termination Resistor r © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FMS6145 • Rev. 2.0.6 9

F M Physical Dimensions S 6 1 4 5 — 0.43 TYP 0.65 L o w - C o s t F i v e - C 1.65 h a n n e l 4 t h 0.45 6.10 -O r d e r S t a n d a r d D e 12.00°TOP & BOTTOM fi n R0.09 min i t i o n V i d e o F A. CONFORMS TO JEDEC REGISTRATION MO-153, i l VARIATION AB, REF NOTE 6 1.00 R0.09min te r B. DIMENSIONS ARE IN MILLIMETERS D C. DIMENSIONS ARE EXCLUSIVE OF BURRS, MOLD FLASH, ri v AND TIE BAR EXTRUSIONS e D. DIMENSIONING AND TOLERANCES PER ANSI r Y14.5M, 1982 E. LANDPATTERN STANDARD: SOP65P640X110-14M F. DRAWING FILE NAME: MTC14REV6 Figure 17. TSSOP-14 Package Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifi cations do not expand the terms of Fairchild’s worldwide terms and conditions, specifi cally the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FMS6145 • Rev. 2.0.6 10

F M S 6 1 4 5 — L o w - C o s t F i v e - C h a n n e l 4 t h - O r d e r S t a n d a r d D e fi n i t i o n V i d e o F i l t e r D r i v e r © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FMS6145 • Rev. 2.0.6 11

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: N. American Technical Support: 800−282−9855 Toll Free ON Semiconductor Website: www.onsemi.com Literature Distribution Center for ON Semiconductor USA/Canada 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Europe, Middle East and Africa Technical Support: Order Literature: http://www.onsemi.com/orderlit Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Phone: 421 33 790 2910 Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Japan Customer Focus Center For additional information, please contact your local Email: orderlit@onsemi.com Phone: 81−3−5817−1050 Sales Representative © Semiconductor Components Industries, LLC www.onsemi.com www.onsemi.com 1

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: O N Semiconductor: FMS6145MTC14X