0.5 mm Pitch, 1.0 mm above the board Top and Top/Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors FH34(S)Series Increased FPC/FFC holding force Space saving (30 pos. shown) Actuator Metal fittings 1.0mm 17mm 3.2mm Easy FPC/FFC insertion Back opening rotating All four sides are 17 m m chamfered. Top contacts FPC / FFC Ready to insert FPC/FFC ■ Features DDeelliivveerreedd wwiitthh tthhee aaccttuuaattoorr ooppeenn 1. Low-profile With the 1.0 mm above the board and width of 3.8 mm the connectors are used in space saving applications. 2. Increased FPC/FFC retention As compared with existing similar construction connectors: * In horizontal direction: Approximately 2.6 times * In vertical direction: Approximately 2 times 3. Unique Back-Flip rotating actuator FFPPCC The rotating actuator opens from the back of the connector, assuring reliable electrical and mechanical connection. FPC/FFC inserted and retained. 4. Easy FPC insertion and reliable electrical Completed electrical and mechanical connection. connection Proven Flip Lock actuator allows easy insertion of FPC and provides a tactile sensation when fully closed, confirming complete electrical and mechanical connection. 5. Delivered with the actuator open FPC/FPC can be immediately inserted without the need for the opening of the actuator. 6. Accepts standard FPC thickness 0.3mm thick standard Flexible Printed Circuit (FPC) can be used. This is the only ultra-low profile ZIF connector using standard FPC. 7. Compatible with existing connectors. FPC/FFC and PCB mounting patterns are the same as for the FH19SC Series (bottom contact), allowing the use of both connectors for interconnections between two boards or replacement of the connectors. Compatible with existing connectors.(FH19SC SERIES) 8. Conductive traces on the PCB can run under the connector No exposed contacts on the bottom of the connector. 9. Board placement with automatic equipment Flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. Standard reel packaging contains 5000 connectors. 10.Halogen-free* *As defined by IEC61249-2-21 Br-900ppm maximum, Cl-900ppm maximum, Cl + Br combined-1,500ppm maximum 2013.11w 1

FH34(S)Series●0.5 mm Pitch, 1.0 mm above the board Top and Top Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Specifications Operating temperature range: Storage temperature range: Current rating 0.5 A (Note 1) -55 to +85°C (Note 1) -10 to +50°C (Note 2) Ratings Operating humidity range: Storage humidity range: Voltage rating 50 Vrms AC Relative humidity 90% max. (No condensation) Relative humidity 90% max. (No condensation) Recommended FPC/FFC Thickness: 0.3 ± 0.03 mm, Gold plated contact pads Item Specification Conditions 1. Insulation resistance 500 Mø min. 100 V DC 2. Withstanding voltage No flashover or insulation breakdown 250 Vrms AC / one minute 100 mø max. 3. Contact resistance 1 mA, AC / DC 20mV max (AC: 1kHz) * Including FPC and FFC conductor resistance Contact resistance: 100 mø max. 4. Durability 20 cycles No damage, cracks, or parts dislocation No electrical discontinuity of 1μs or longer Frequency: 10 to 55 Hz, single amplitude of 0.75 5. Vibration Contact resistance: 100 mø max. mm, 10 cycles in each of the 3 axis No damage, cracks, or parts dislocation No electrical discontinuity of 1μs or longer Acceleration of 981m/s2, 6 ms duration, sine half- 6. Shock Contact resistance: 100 mø max. wave, 3 cycles in each of the 3 axis No damage, cracks, or parts dislocation Contact resistance: 100 mø max. 7. Humidity (Steady state) Insulation resistance: 50 Mø min. 96 hours at 40°C and humidity of 90 to 95% No damage, cracks, or parts dislocation Contact resistance: 100 mø max. Temperature :-55°C/+15°C to +35°C/+85°C/+15°C to +35°C 8. Temperature cycle Insulation resistance: 50 Mø min. Time: 30 / 2 to 3 / 30 / 2 to 3 minutes No damage, cracks, or parts dislocation 5 cycles Reflow: At the recommended temperature profile 9. Resistance to soldering heat No deformation of components affecting performance Manual soldering: 350°C ±5°C for 5 seconds (Note 3) Note1: When passing the current through all of the contacts, use 70% of the rated current. Note2: Includes temperature rise caused by current flow. Note3: The term "storage" refers to products stored for a long period prior to mounting and use. The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment or during transportation after board mounting. ■Materials Part Material Finish Remarks FH34S series Color:Beige LCP FH34SRJ series Color:Gray UL94V-0 Insulator FH34S series PA Color:Black FH34SRJ series LCP(8pos.) FH34SRJ series Color:Black UL94V-0 Contacts Phosphor bronze Gold plating with nickel barrier ------- Metalfittings Phosphor bronze Pure tin reflow plating ------- ■Ordering information FH 34S RJ - 30S - 0.5 SH (50) 1 2 3 4 5 6 7 1 Series name : FH 6 Termination type 2 Series No. : 34S SH : SMT horizontal mounting type 3 Blank : Top contact 7 Specifications RJ : Top and Bottom contact, halogen-free (50)…Standard product 5,000 pieces/reel (Flame retardance UL94V-0). (99)…500 pieces/reel 4 Number of positions : 4 to 40 5 Contact pitch: 0.5mm 2

FH34(S)Series●0.5 mm Pitch, 1.0 mm above the board Top and Top Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Connector Dimensions A±0.15 B H 0.5 ∞Number of contacts(0.15) 0.15H 2) 95) (3. 1. ( Number of contacts indicator HRS mark (3.8) Cav No. 2.9 **A 5) 1 7 ±0. (1. 1 0.5 0.3 (0.15) 2.9 (C) 0.1 1 D±0.1 Note 1 : The coplanarity of each terminal lead within specified dimension is 0.1 mm Max. Note 2 : Packaged on tape and reel only. Check packaging specification. Note 3 : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. Note 4 : After reflow, the terminal plating may change color, however this does not represent a quality issue. All dimensions: mm Part Number CL No. Number of Contacts A B C D FH34S-7S-0.5SH(50) CL580-1224-2-50 7 5.5 3 4.03 4.88 FH34S-23S-0.5SH(50) CL580-1228-3-50 23 13.5 11 12.07 12.88 FH34S-32S-0.5SH(50) CL580-1208-6-50 32 18 15.5 16.53 17.38 FH34SRJ-4S-0.5SH(50) CL580-1238-7-50 4 4 1.5 2.53 3.38 FH34SRJ-6S-0.5SH(50) CL580-1236-1-50 6 5 2.5 3.53 4.38 FH34SRJ-8S-0.5SH(50) CL580-1231-8-50 8 6 3.5 4.53 5.38 FH34SRJ-10S-0.5SH(50) CL580-1251-5-50 10 7 4.5 5.53 6.38 FH34SRJ-11S-0.5SH(50) CL580-1258-4-50 11 7.5 5 6.03 6.88 FH34SRJ-12S-0.5SH(50) CL580-1253-0-50 12 8 5.5 6.53 7.38 FH34SRJ-14S-0.5SH(50) CL580-1252-8-50 14 9 6.5 7.53 8.38 FH34SRJ-16S-0.5SH(50) CL580-1259-7-50 16 10 7.5 8.57 9.38 FH34SRJ-18S-0.5SH(50) CL580-1248-0-50 18 11 8.5 9.57 10.38 FH34SRJ-20S-0.5SH(50) CL580-1256-9-50 20 12 9.5 10.57 11.38 FH34SRJ-22S-0.5SH(50) CL580-1254-3-50 22 13 10.5 11.57 12.38 FH34SRJ-24S-0.5SH(50) CL580-1255-6-50 24 14 11.5 12.57 13.38 FH34SRJ-26S-0.5SH(50) CL580-1247-8-50 26 15 12.5 13.57 14.38 FH34SRJ-30S-0.5SH(50) CL580-1232-0-50 30 17 14.5 15.57 16.38 FH34SRJ-34S-0.5SH(50) CL580-1261-9-50 34 19 16.5 17.53 18.38 FH34SRJ-40S-0.5SH(50) CL580-1260-9-50 40 22 19.5 20.53 21.38 Tape and reel packaging (5,000 pieces/reel, 500 pieces/reel). Order by number of reels. 3

FH34(S)Series●0.5 mm Pitch, 1.0 mm above the board Top and Top Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Recommended PCB mounting pattern and metal mask dimensions Recommended metal mask thickness: t=0.1 ±0.05 5±0.03al mask) 0.5 ∞Number of Bco0n.t1acJts 0.3±0.05 J 5) 5) 0.8 0.6(Met (M0.e2t5a±l m0.a0s3k) (0.2 (0.2 5 0 3.3±0. 0.15) (2.9) ( ±0.05 (0.065) (0.185) (0.15) 8 0. E±0.1 F±0.1 (A) ■Recommended FPC/FFC Dimensions G±0.05 0.5±0.07 B±0.03 R0.2 0.5±0.03 0.3±0.03 2- 0.3±0.03 er) n e Stiff N( a) MI ±0.3 er are H 2.5 5 v 1. co n U ( Note 1 : Stiffener dimension should be 2.5mm min., and H dimension should be 0.5mm for improved flexibility of FPC. Note 2 : When using the FPC/FFC in FH34S or FH19SC connectors, the exposed area inserted in either connector is 2.5mm ± 0.3mm and the stiffener is 3.5mm min. All dimensions: mm Part Number CL No. Number of Contacts A B E F G FH34S-7S-0.5SH(50) CL580-1224-2-50 7 5.5 3 4.6 5.4 4 FH34S-23S-0.5SH(50) CL580-1228-3-50 23 13.5 11 12.6 13.4 12 FH34S-32S-0.5SH(50) CL580-1208-6-50 32 18 15.5 17.1 17.9 16.5 FH34SRJ-4S-0.5SH(50) CL580-1238-7-50 4 4 1.5 3.1 3.9 2.5 FH34SRJ-6S-0.5SH(50) CL580-1236-1-50 6 5 2.5 4.1 4.9 3.5 FH34SRJ-8S-0.5SH(50) CL580-1231-8-50 8 6 3.5 5.1 5.9 4.5 FH34SRJ-10S-0.5SH(50) CL580-1251-5-50 10 7 4.5 6.1 6.9 5.5 FH34SRJ-11S-0.5SH(50) CL580-1258-4-50 11 7.5 5 6.6 7.4 6 FH34SRJ-12S-0.5SH(50) CL580-1253-0-50 12 8 5.5 7.1 7.9 6.5 FH34SRJ-14S-0.5SH(50) CL580-1252-8-50 14 9 6.5 8.1 8.9 7.5 FH34SRJ-16S-0.5SH(50) CL580-1259-7-50 16 10 7.5 9.1 9.9 8.5 FH34SRJ-18S-0.5SH(50) CL580-1248-0-50 18 11 8.5 10.1 10.9 9.5 FH34SRJ-20S-0.5SH(50) CL580-1256-9-50 20 12 9.5 11.1 11.9 10.5 FH34SRJ-22S-0.5SH(50) CL580-1254-3-50 22 13 10.5 12.1 12.9 11.5 FH34SRJ-24S-0.5SH(50) CL580-1255-6-50 24 14 11.5 13.1 13.9 12.5 FH34SRJ-26S-0.5SH(50) CL580-1247-8-50 26 15 12.5 14.1 14.9 13.5 FH34SRJ-30S-0.5SH(50) CL580-1232-0-50 30 17 14.5 16.1 16.9 15.5 FH34SRJ-34S-0.5SH(50) CL580-1261-9-50 34 19 16.5 18.1 18.9 17.5 FH34SRJ-40S-0.5SH(50) CL580-1260-9-50 40 22 19.5 21.1 21.9 20.5 4

FH34(S)Series●0.5 mm Pitch, 1.0 mm above the board Top and Top Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Recommended FPC construction ●Contact FPC manufacturer for specific details. 1. Using Single-sided FPC FPC : Flexible Printed Circuit Material Thickness Material Name Material (μm) Covering film layer Polyimide 1 mil thick (25) Cover adhesive (25) 0.2μm thick gold plated over 1 Surface treatment 3 to 5μm thick nickel underplating Copper foil Cu 1oz 35 Base adhesive Thermosetting adhesive 25 Base film Polyimide 1 mil thick 25 Reinforcement material adhesive Thermosetting adhesive 35 Stiffener Polyimide 7 mil thick 175 Total 298 2. Using Double-sided FPC FPC : Flexible Printed Circuit Material Thickness Material Name Material (μm) Covering layer film Polyimide 1 mil thick (25) Cover adhesive (25) 0.2μm thick gold plated over 1 Surface treatment 3 to 5μm thick nickel underplating Through-hole copper Cu 15 Copper foil Cu 1/2oz 18 Base adhesive Thermosetting adhesive 18 Base film Polyimide 1 mil thick 25 Base adhesive 18 Copper foil Cu 1/2oz (18) Cover adhesive Thermosetting adhesive 25 Covering film layer Polyimide 1 mil thick 25 Reinforcement material adhesive Thermosetting adhesive 50 Stiffener Polyimide 4 mil thick 100 Total 297 * To prevent release of the FPC due to its bending, use of the double sided FPC with copper foil on the back side is not recommended. 3. Using FFC FFC : Flexible Flat Cable Material Thickness Material Name Material (μm) Polyester film (12) Adhesive Thermoplastic polyester (30) Gold plated annealed copper foil 35 Adhesive Polyester 30 Polyester 12 Adhesive Polyester 30 Stiffener Polyester 188 Total 295 4. Precautions 1. This specification is a recommendation for the construction of the FH34S Series FPC and FFC (t=0.3 ± 0.03). 2. For details about the construction, please contact the FPC/FFC manufacturers. 5

FH34(S)Series●0.5 mm Pitch, 1.0 mm above the board Top and Top Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Packaging Specification ●Embossed Carrier Tape Dimensions ●Embossed Carrier Tape Dimensions (Tape width 24mm max.) (Tape width of 32mm min.) (2.25) 4±0.1 2±0.15 8±0.1 Ø1.5+0. 10 5±0.1 (2.25)(0.3) Ø1.5+0. 10 1.75±0.1 7 (0.3) 1. 1 0. ± 1 M M±0. 0.3 N±0.1 L±0.3 ± L ((34.2)) Ffaoulart top smlaucareftaimcc eeeq,nut iwpimthent 1.5+ 00.1 +0.15 0 (1.95) (1.95) 1.7 Unreeling direction Unreeling direction Flat surface, for placement with automatic equipment ●Reel Dimensions 5 0. ± 3 Ø1 (Q: INSIDE) (Ø380) (Ø80) (R: OUTSIDE) End section Mounting section Lead section (400mm min.) Embossed carrier tape Top cover tape No connector inserted No connector inserted (10 pockets min.) (10 pockets min.) All dimensions: mm Part Number CL No. Number of Contacts L M N Q R FH34S-7S-0.5SH(50) CL580-1224-2-50 7 16 7.5 — 17.4 21.4 FH34S-23S-0.5SH(50) CL580-1228-3-50 23 24 11.5 — 25.4 29.4 FH34S-32S-0.5SH(50) CL580-1208-6-50 32 32 14.2 28.4 33.4 37.4 FH34SRJ-4S-0.5SH(50) CL580-1238-7-50 4 16 7.5 — 17.4 21.4 FH34SRJ-6S-0.5SH(50) CL580-1236-1-50 6 16 7.5 — 17.4 21.4 FH34SRJ-8S-0.5SH(50) CL580-1231-8-50 8 16 7.5 — 17.4 21.4 FH34SRJ-10S-0.5SH(50) CL580-1251-5-50 10 16 7.5 - 17.4 21.4 FH34SRJ-11S-0.5SH(50) CL580-1258-4-50 11 16 7.5 - 17.4 21.4 FH34SRJ-12S-0.5SH(50) CL580-1253-0-50 12 24 11.5 - 25.4 29.4 FH34SRJ-14S-0.5SH(50) CL580-1252-8-50 14 24 11.5 - 25.4 29.4 FH34SRJ-16S-0.5SH(50) CL580-1259-7-50 16 24 11.5 - 25.4 29.4 FH34SRJ-18S-0.5SH(50) CL580-1248-0-50 18 24 11.5 - 25.4 29.4 FH34SRJ-20S-0.5SH(50) CL580-1256-9-50 20 24 11.5 - 25.4 29.4 FH34SRJ-22S-0.5SH(50) CL580-1254-3-50 22 24 11.5 - 25.4 29.4 FH34SRJ-24S-0.5SH(50) CL580-1255-6-50 24 24 11.5 - 25.4 29.4 FH34SRJ-26S-0.5SH(50) CL580-1247-8-50 26 24 11.5 - 25.4 29.4 FH34SRJ-30S-0.5SH(50) CL580-1232-0-50 30 32 14.2 28.4 33.4 37.4 FH34SRJ-34S-0.5SH(50) CL580-1261-9-50 34 32 14.2 28.4 33.4 37.4 FH34SRJ-40S-0.5SH(50) CL580-1260-9-50 40 44 20.2 40.4 45.4 49.4 6

FH34(S)Series●0.5 mm Pitch, 1.0 mm above the board Top and Top Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Operation and Precautions Exercise care when handling connectors. Follow recommendations given below. Operation Precautions 1. As delivered Delivered with the actuator open. There is • Do not close the actuator without the FPC/FPC no need to operate the inserted. actuator prior to inserting the FPC/FFC. 2. FPC/FFC insertion (The top contact specification) •The contacts are making connection with the Insert the FPC/FFC with FPC/FFC pads from the top. the conductive surfaces Do not insert the FPC/FFC with the pads facing facing up. down. Align the FPC/FFC When inserting the FPC/FFC do not twist it. Insert straight with the straight. Improper insertion may cause deformation connector and insert it FPC/FFC contact surfaces face up. of the contacts and connection failures. firmly all the way. •Be sure to insert the FPC/FFC when the actuator is fully open. 3. Locking After FPC/FFC insertion, rotate the actuator down •Do not operate the actuator by only one end. Open to a full stop, pushing it at the center. or close by pushing at the center. •Do not try to rotate the actuator past the fully open 90° position. This will damage the connector, preventing it from use. •Do not apply excessive force to the connector when the actuator is closed. Rotate Push at the center of the actuator. 4. FPC/FFC removal (Lock release) Carefully rotate the actuator up to 90°, lifting it at •Do not operate the actuator from one end only. the center. •The actuator opens only 90°. Do not attempt to open it past this angle or grasp it. •During the opening of the actuator do not press it toward the connector body. Rotate up at the center. Raise Lift at the center 7

FH34(S)Series●0.5 mm Pitch, 1.0 mm above the board Top and Top Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Precautions at the Design Stage (1) Route the FPC/FFC so that a direct pull force (2) Make sure that there is enough space to insert/remove the FPC/FFC straight. (3) Follow the recommendations given in this catalog in regard to mounting pattern, metal mask dimensions and FPC/FFC mating dimensions. (4) Consult the manufacturer of the FPC/FFC for the details on the flexibility of the specific FPC/FFC. (5) When designing the board lay-out and spaces in the device assure that there is enough clearances for the actuator to fully open/close. ■Precautions when mounting connectors on the PCB ◆Handling before mounting on PCB Insertion of the FPC/FFC or operation of the actuator prior to mounting on the PCB is not recommended. ◆PC board warpage Minimize the warpage as much as possible. The connector are straight within 0.1 mm max. Make sure that the mounting area flatness can accept the connector terminals without causing any failure of the solder joints. ◆Forces on the board ◆When braking the large PC board into individual boards exercise care not to damage the installed connectors. ◆When attaching the boards or other components with the screws Connectors make sure that any stresses will not cause board deflections affecting the mounting areas of the connector. PCB ◆When hand soldering: · Do not perform hand soldering with the FPC inserted in the connector. * Do not apply excessive heat or touch the soldering iron anywhere other than the connector leads. * Do not use excessive amount of solder or flux compounds. Operation of the actuator or contacts may be affected by excessive amounts of solder or flux compounds. ■Temperature Profile MAX 250ç HRS test condition Solder method : Reflow, IR/hot air 250 Environment : Room air 230ç Solder composition : Paste, 96.5%Sn/3.0%Ag/0.5%Cu (Senju Metal Industry, Co., Ltd.'s Part 200 200ç ç) Number: e( ur M705-221CM5-42-10.5) at mper 150 150ç Test board : Glass epoxy e 25mm∞40mm∞0.8mm thick T Land dimensions : 0.3mm∞0.8mm 100 Metal mask : 0.25∞0.65∞0.1mm thick 50 The temperature profiles shown are based on the above conditions. 25ç(60 sec.) 90 to 120 sec. (60 sec.) In individual applications the actual temperature may Preheating Soldering 0 vary, depending on solder paste type, volume / thickness Start and board size / thickness. Consult your solder paste and Time (Seconds) equipment manufacturer for specific recommendations. 8