Thermal motor protector Temperature limiter Thermal cut-out 13 20 23 Applications - Motors - Transformers - Coils - Electronics, sensors Benefits - Small dimensions - Shock and vibration tested - Leadframe version - Tested for audio, video applications (EN 60065)

Technical data control type F20A / E F13A 1) F23A / E F20B / G ratings version normally closed normally open rated current at 250 V 50/60 Hz ( power factor 0.95 / 0.6 ) 2.0 A / 1.6 A 3.0 A / 2.5 A 3.0 A / 3.0 A 2.0 A / 1.6 A switching cycles under rated current 7,000 10,000 10,000 7,000 max. current under failure condition at 250 V 50/60 Hz ( power factor 0.95 ) 4.0 A 5.0 A 4.0 A switching cycles under max. current 3,000 temperature rating Ta ( steps in 5 K ) 70 °C ... 190 °C 70 °C ... 185 °C tolerances standard: ± 5 K feature of automatic action 1.B, 2.B.M, 1.C 2.B, 1.C contact resistance ( incl. wire of 100 mm ) < 50 mΩ hysteresis 30 K ± 15 K 2) dielectric strength ( standard insulation ) 2 kV shock / vibration testing ( similar to EN 50155 ) 400 m/s2 sine half wave / 100 m/s2 5 Hz ... 2,000 Hz sine resistances to impregnation tight against ordinary resins and lacquers degrees of protection provided by enclosures ( EN 60529 ) IP00 suitable for use in protection category I, II VDE / ENEC EN 60730-1 / -2-9 UL UL File Number E46827 approvals cUL C22.2 No. 77 / C22.2 No. 24 1) CQC GB14536.1-1998 / GB14536.10-1996 3) 1)details on request 2)at the Ta (upper and lower) limits the hysteresis could deviate 3)different power rating Standard wire ( length 100 ± 10 mm, stripped 6 ± 1 mm ) operating Cantherm Cantherm temperature diameter cross section UL voltage lead code max. insulation diameter 1) style max. black ACFA 1.57 mm AWG24 / 0.24 mm2 150 °C 300 V 3266/3398 yellow AEFC 1.80 mm AWG20 / 0.48 mm2 black KCFA 1.2 mm AWG24 / 0.25 mm2 200 °C 600 V 10086 black KEFA 1.6 mm AWG20 / 0.50 mm2 2) black ASFA 150 °C 300 V 1.65 mm AWG20 / 0.81 mm 3266/3398 white DCFB 1.21 mm AWG24 / 0.51 mm 200 °C 300 V 1180 white DEFB 1.51 mm AWG20 / 0.81 mm 1) AWG24 is recommended 2) Solid Wire Note: Additional wires available upon request.

Standard insulation control Cantherm drawing technical nc no illustration approvals type code dimensions ( mm ) specifi cation F13 A U102 | B shrink cap VDE, UL, potted cUL F20, F23 A B U106 | F different dimensions for F20, F23 F13 A U198 cap of PPS VDE, UL, potted cUL F20, F23 A B U185 different dimensions for F20, F23 Specific variations control Cantherm drawing technical nc no illustration approvals type code dimensions ( mm ) specifi cation Insulation not insulated VDE, UL F13 A None | 0 potted cUL Insulation not insulated VDE, UL, F20, F23 A B None | 0 potted cUL, CSA F13 A Insulation VDE, UL coated U112 | L cUL F20, F23 A B different dimensions for F20, F23 Housing housing of PPS G410 | 6 leadframe leads VDE, UL, F20, F23 A B grid dimension 5.08 cUL, CSA Leads potted A150 | 36 F13 A Leads not insulated VDE, UL A800 | IZA potted cUL F20, F23 A B ddiiffffeerreenntt ddiimmeennssiioonnss ffoorr FF2200,, FF2213 alluminium housing thread M4x6 VDE, UL, F20, F23 E G G700 | B potted cUL, CSA Ta max. 150 °C G410 | 6 housing of PPS VDE, UL F13 A potted cUL Leads | ACFA F13 A A150 | 36 leadframe leads VDE, UL, grid dimension 5.08 cUL, CSA F20, F23 A B U112 | L coated different dimensions for F20, F23

Heating by current K] g [ n ati e h - elf s current [A] The characteristic curve in the diagram is measured with a thermal control without any insulation in an oil bath. Attention: The heating depends on the thermal conduction of the control to the equipment or part which should be protected. Ordering and marking example Ordering example (Microtherm) Marking F20 A 120 05 L310 100 U254 F20A type (F20 nc) 12005 response temperature (120°C), tolerance (± 5K) shrink cap insulation 049D date of manufacture (April 2009), country (D=Germany) length 100 mm lead wire white, AWG20 tolerance temperatue normally closed type Deviations from standard controls on request. Cantherm Ordering Example [ F20A12005ACFA06E ] F20 A 120 05 AC F A 0 6 E wire leads lead housing tolerance color no strip type Norm. Closed Temp. UL3398 length - G410 +/-5°C black insulation .25" 24 F=6" E06 AWG Marking F20A type (F20 nc) 12005 response temperature (120°C), tolerance (± 5K) 065C date of manufacture (June 2015), country (C = Canada) TM Div. of Microtherm International Cooperation Canadian Thermostats & Control Devices, Ltd. Tel: (514) 739-3274 Fax: (514) 739-2902 1 (800) 561-7207 8415 Mountain Sights Ave. Montreal, Canada H4P 2B8 WEBSITE: www.cantherm.com E-Mail: sales@cantherm.com 2016/NOV Subject to change without notice