Chip Resistor Networks Chip Resistor Networks Type: EXBD EXBE EXBA EXBQ Features ● High density placing for digital signal circuits · Bussed 8 or 15 resistors for pull up/down circuits EXBD: 3.2 mm × 1.6 mm × 0.55 mm, 0.635 mm pitch EXBE: 4.0 mm × 2.1 mm × 0.55 mm, 0.8 mm pitch EXBA: 6.4 mm × 3.1 mm × 0.55 mm, 1.27 mm pitch EXBQ: 3.8 mm × 1.6 mm × 0.45 mm, 0.5 mm pitch · Available direct placing on the bus line by means of half pitch spacing without through-holes on PWB (“High density placing” is shown below) ● High speed mounting using conventional placing machine ● Reference Standard…IEC 60115-9, JIS C 5201-9, EIAJ RC-2130 ● RoHS compliant [High density placing] Pull up resistors Direct placement on the bus line VCC EXBE10C EXBA10P VCC VCC IC IC IC IC IC IC No through hole Through holes 0.4 mm pitch 0.635 mm pitch ■ As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions, Please see Data Files Explanation of Part Numbers 1 2 3 4 5 6 7 8 9 10 11 12 E X B E 1 0 C 1 0 3 J Product Code Dimension Code of Circuit Configuration Resistance Value Resistance Suffix for Special Thick Film Chip Resistor Network Code Common Terminal Position The first two digits are Tolerance Requirements Resistor Code Inch Dimensions Center common circuit significant figures of J ±5 % Network D 1206 3.2 mm×1.6 mm C (EXBD, EXBE) resistance value and E 1608 4.0 mm×2.1 mm Diagonal common circuit the third one denotes the number of zeros A 2512 6.4 mm×3.1 mm P (Terminal 5 and Terminal 10) following. Q 1506 3.8 mm×1.6 mm (EXBA) One side common circuit P (Terminal 16) Number of (EXBQ) Terminals Diagonal common circuit 10(EXBD,E,A) E (Terminal 1 and Terminal 6) 16(EXBQ) (EXBA) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 02 Sep. 2014

Chip Resistor Networks Construction (Example : EXBD) Protective coating Protective coating Electrode (Inner) Alumina substrate Thick film Electrode (Outer) resistive element Electrode (Between) Thick film Alumina substrate Electrode (Inner) resistive element Dimensions in mm (not to scale) EXBD EXBE EXBA EXBQ 0.2±0.40±0.150.40±0.150.1 0.06.3f2505±3.±02.020.±.30.101±±0.00100..1.1353±0.150.2±0.1000.35±0.15..220.2±0.15±0.35±0.15±000..15.150±0.1.60±0.1510 0.350.±30±0.5±0.2.020.5±0.2.02f0.3+ –00..214I00..00.45±±0±0.0308...2±220.1 0.4±0.2000.25±0.20..330.4±0.2±0.25±0.205±0.02.20 2.1±0.20.55±0.10 f0.6I31.040+ .–0200.±...7721503±±±.0200...2120 0.3±0.20.5±0.20.3±0.20.5±0.2 3.1±0.20.55±0.1EE0XXBBAAII00110033EP +0.150.15 –0.05 0.3±03.10.8.5±04±00.01..22.57±1+ 0–00.12..2005 0.150.25±0.150.30±0.15+ –00..1055 1.6±0.20.45±0.10 Mass (Weight)[1000 pcs.] : 10 g Mass (Weight)[1000 pcs.] : 16 g Mass (Weight)[1000 pcs.] : 40 g Mass (Weight)[1000 pcs.] : 9 g Circuit Confi guration EXBD, EXBE EXBA EXBQ EXBA10P EXBA10E 10 9 8 7 10 9 8 7 6 10 9 8 7 6 16 15 14 13 12 11 10 9 1 6 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 6 7 8 Ratings Item Specifi cations Series EXBD EXBE EXBA EXBQ Resistance Range 47 Ω to 1 MΩ (E12) 100 Ω to 470 kΩ (E6 series) Resistance Tolerance ±5% Number of Terminals 10 terminals 16 terminals Number of Resistors 8 element 15 element Power Rating at 70 °C 0.05 W/element 0.063 W/element 0.025 W/element Limiting Element Voltage(1) 25V 50 V 25V Maximum Overload Voltage(2) 50 V 100 V 50 V T. C. R. ±200 × 10–6/ °C Category Temperature Range –55 °C to +125 °C (1) Rated Continuous Working Voltage (RCWV) shall be determined from RCWV=√Power Rating × Resistance Value, or Limiting Element Voltage listed above, whichever less. (2) Overload (Short-time Overload) Test Voltage (SOTV) shall be determinedfrom SOTV=2.5 × RCWV✽ or Maximum Overload Voltage list ed above which ev er less. Power Derating Curve –55 °C 70 °C For resistors operated in ambient temperatures above %)100 70 °C, power rating shall be derated in accordance d ( 80 a with the figure on the right. Lo 60 ed 40 at R 20 125 °C 0 –60–40–20 0 20 40 60 80100120140160180 Ambient Temperature (°C) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 02 Sep. 2014

Surface Mount Resistors Safety precautions Safety Precautions (Common precautions for Surface Mount Resistors) The following are precautions for individual products. Please also refer to the common precautions for Fixed Resistors in this catalog. 1. Take measures against mechanical stress during and after mounting of Surface Mount Resistors (hereafter called the resistors) so as not to damage their electrodes and protective coatings. Be careful not to misplace the resistors on the land patterns. Otherwise, solder bridging may occur. 2. Keep the rated power and ambient temperature within the specified derating curve. Some circuit boards, wiring patterns, temperatures of heat generated by adjacent components, or amb ie nt tem per a tures can become factors in the rise of the temperature of the res is tors, regardless of the level of power applied. Therefore, check the conditions before use and op ti mize them so as not to damage the boards and peripheral components. Make sure to contact us before using the resistors under special conditions. 3. If a transient load (heavy load in a short time) like a pulse is expected to be applied, check and evaluate the operations of the resistors when installed in your products before use. Never exceed the rated power. Otherwise, the performance and/or reliability of the resistors may be impaired. 4. Before using halogen-based or other high-activity flux, check the possible effects of the flux residues on the per for mance and reliability of the resistors. 5. When soldering with a soldering iron, never touch the resistors'bodies with the tip of the soldering iron. When using a soldering iron with a high temperature tip, finish soldering as quickly as possible (within three seconds at 350 °C max.). 6. As the amount of applied solder becomes larger, the mechanical stress applied to the resistors increases, causing problems such as cracks and faulty characteristics. Avoid applying an excessive amounts of solder. 7. When the resistors' protective coatings are chipped, flawed, or removed, the characteristics of the resistors may be impaired. Take special care not to apply mechanical shock during automatic mounting or cause damage during handling of the boards with the resistors mounted. 8. Do not apply shock to the resistors or pinch them with a hard tool (e.g. pliers and tweezers). Otherwise, the resistors' protective coatings and bodies may be chipped, affecting their performance. 9. Avoid excessive bending of printed circuit boards in order to protect the resistors from abnormal stress. 10. Do not immerse the resistors in solvent for a long time. Before using solvent, carefully check the effects of imm er sion. 11. Transient voltage If there is a possibility that the transient phen om e non (significantly high voltage ap plied in a short time) may occ ur or that a high voltage pulse may be applied, make sure to evaluate and check the chara ct er is tics of Fixed Metal (Oxide) Film Resistors mounted on your product rather than only depending on the calculated pow er limit or steady-state conditions to complete the des ign or decide to use the resistors. 12. Do not apply excessive tension to the terminals. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 02 Sep. 2014

Safety Precautions (Common precautions for Fixed Resistors) • When using our products, no matter what sort of equipment they might be used for, be sure to make a written agreement on the specifications with us in advance. The design and specifications in this catalog are subject to change without prior notice. • Do not use the products beyond the specifications described in this catalog. • This catalog explains the quality and performance of the products as individual components. Before use, check and evaluate their operations when installed in your products. • Install the following systems for a failsafe design to ensure safety if these products are to be used in equipm ent where a defect in these products may cause the loss of human life or other significant dam age, such as damage to vehicles (automobile, train, vessel), traffic lights, medical equipment, aerospace equipment, electric heating appliances, combustion/gas equipment, rotating equipment, and disaster/crime prevention equipment. ✽ Systems equipped with a protection circuit and a protection device ✽ Systems equipped with a redundant circuit or other system to prevent an unsafe status in the event of a sing le fault (1) Precautions for use • These products are designed and manufactured for general and standard use in general elect ron ic equipment (e.g. AV equipment, home electric appliances, office equipment, information and communication equipment) • These products are not intended for use in the following special conditions. Before using the products, carefully check the effects on their quality and performance, and determine whether or not they can be used. 1. In liquid, such as water, oil, chemicals, or organic solvent 2. In direct sunlight, outdoors, or in dust 3. In salty air or air with a high concentration of corrosive gas, such as Cl, H S, NH , SO , or NO 2 2 3 2 2 4. Electric Static Discharge (ESD) Environment These components are sensitive to static electricity and can be damaged under static shock (ESD). Please take measures to avoid any of these environments. Smaller components are more sensitive to ESD environment. 5. Electromagnetic Environment Avoid any environment where strong electromagnetic waves exist. 6. In an environment where these products cause dew condensation 7. Sealing or coating of these products or a printed circuit board on which these products are mounted, with resin or other materials • These products generate Joule heat when energized. Carefully position these products so that their heat will not affect the other components. • Carefully position these products so that their temperatures will not exceed the category temperature range due to the effects of neighboring heat-generating components. Do not mount or place heat-generating components or inflammables, such as vinyl-coated wires, near these products. • Note that non-cleaning solder, halogen-based highly active flux, or water-soluble flux may deteriorate the performance or reliability of the products. • Carefully select a flux cleaning agent for use after soldering. An unsuitable agent may deteriorate the performance or reliability. In particular, when using water or a water-soluble cleaning agent, be careful not to leave water residues. Otherwise, the insulation performance may be deteriorated. (2) Precautions for storage The performance of these products, including the solderability, is guaranteed for a year from the date of arr iv al at your company, provided that they remain packed as they were when delivered and stored at a temp er a ture of 5 °C to 35 °C and a relative humidity of 45 % to 85 %. Even within the above guarantee periods, do not store these products in the following conditions. Otherwise, their electrical performance and/or solderability may be deteriorated, and the packaging materials (e.g. taping materials) may be deformed or deteriorated, resulting in mounting failures. 1. In salty air or in air with a high concentration of corrosive gas, such as Cl, H S, NH , SO , or NO 2 2 3 2 2 2. In direct sunlight <Package markings> Package markings include the product number, quantity, and country of origin. In principle, the country of origin should be indicated in English. 01 Sep. 2014

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: P anasonic: EXB-A10P563J EXB-D10C151J EXB-D10C820J EXB-E10C680J EXB-E10C331J EXB-A10P101J EXB-A10P102J EXB-A10E103J EXB-D10C750J EXB-E10C121J EXB-E10C151J EXB-A10E472J EXB-E10C222J EXB-A10P103J EXB-A10P104J EXB-A10P221J EXB-A10P332J EXB-A10P471J EXB-A10P472J EXB-A10P473J EXB-D10C102J EXB-D10C103J EXB-D10C104J EXB-D10C182J EXB-D10C183J EXB-D10C221J EXB-D10C272J EXB- D10C332J EXB-D10C472J EXB-D10C473J EXB-D10C560J EXB-D10C683J EXB-D10C822J EXB-E10C103J EXB-E10C104J EXB-E10C223J EXB-E10C272J EXB-E10C273J EXB-E10C332J EXB-E10C472J EXB-E10C560J EXB-Q16P103J EXB-A10P474J EXB-A10E152J EXB-A10E332J EXB-A10E471J EXB-A10E681J EXB-A10E821J EXB-D10C333J EXB-E10C102J EXB-E10C473J EXB-D10C222J EXB-A10P152J EXB-D10C562J EXB-A10P222J EXB-A10E104J EXB-A10E222J EXB-A10E271J EXB-A10E473J EXB-A10P105J EXB-A10P121J EXB-A10P122J EXB-A10P123J EXB-A10P124J EXB-A10P151J EXB-A10P153J EXB-A10P154J EXB-A10P181J EXB-A10P182J EXB-A10P183J EXB-A10P184J EXB-A10P223J EXB-A10P224J EXB-A10P271J EXB-A10P272J EXB-A10P273J EXB-A10P274J EXB-A10P331J EXB-A10P333J EXB-A10P334J EXB-A10P391J EXB-A10P392J EXB-A10P393J EXB-A10P394J EXB-A10P470J EXB-A10P512J EXB-A10P560J EXB-A10P561J EXB-A10P562J EXB-A10P564J EXB-A10P680J EXB-A10P681J EXB-A10P682J EXB-A10P683J EXB-A10P684J EXB-A10P820J EXB-A10P821J EXB-A10P822J EXB-A10P823J EXB-A10P824J