Anti-surge chip resistors ESR series Datasheet Features ● 1)Exclusive resistive element pattern and laser trimming technology results in significantly improved surge resistance characteristics. 2)2kV to 5kV electrostatic discharge resistance. 3)Superior power ratings. 4)ROHM resistors have obtained ISO9001 / ISO / TS16949 certification. 5)Corresponds to AEC-Q200. Products list ● Rated Limiting Operating Size Temperature Resistance Automotive power element Resistance range temperature Part No. coefficient tolerance grade (70℃) voltage range (mm) (inch) available (W) (V) (ppm / ℃) (%) (Ω) (℃) ±100 F ( ±1% ) 10≦R≦976k (E24/96 series) ±100 F ( ±1% ) 1M≦R≦2.2M (E24 series) ESR01 1005 0402 0.20 50 -55 ～ +155 Yes +500/-250 J ( ±5% ) 1≦R≦9.1 (E24 series) ±200 J ( ±5% ) 10≦R≦10M (E24 series) ±100 D ( ±0.5% ) 10≦R≦1M (E24/96 series) ±200 F ( ±1% ) 1≦R<10 (E24/96 series) ESR03 1608 0603 0.25 150 -55 ～ +155 Yes ±100 F ( ±1% ) 10≦R≦10M (E24/96 series) ±200 J ( ±5% ) 1≦R≦10M (E24 series) ±100 D ( ±0.5% ) 10≦R≦1M (E24/96 series) ESR10 2012 0805 0.40 150 ±100 F ( ±1% ) 1≦R≦10M (E24/96 series) -55 ～ +155 Yes ±200 J ( ±5% ) 1≦R≦10M (E24 series) ±100 D ( ±0.5% ) 10≦R≦1M (E24/96 series) ESR18 3216 1206 0.5 200 ±100 F ( ±1% ) 1≦R≦10M (E24/96 series) -55 ～ +155 Yes ±200 J ( ±5% ) 1≦R≦10M (E24 series) ±100 D ( ±0.5% ) 10≦R≦1M (E24/96 series) ESR25 3225 1210 0.66 200 ±100 F ( ±1% ) 1≦R≦10M (E24/96 series) -55 ～ +155 Yes ±200 J ( ±5% ) 1≦R≦10M (E24 series) *E24 : Standard products, E96 : Custom products. Part Number Description ●● E S R 1 0 E Z P J 1 0 0 Part No. Size (mm [inch]) Packaging specifications code Resistance Nominal resistance 01(1005 [0402]) Packaging Quantity tolerance Resistance code, 3 or 4 digits. Part No. Code ESR 03(1608 [0603]) specifications / Reel 000 denotes jumper type. D ( ±0.5% ) (Anti-surge 10(2012 [0805]) ESR01 MZP Paper tape 10,000 F ( ±1% ) Resistance Resistance chip resistors) 18(3216 [1206]) (4mm Pitch) tolerance code J ( ±5% ) 25(3225 [1210]) Paper tape D,F ： 4 digits ESR03 EZP 5,000 (4mm Pitch) J ： 3 digits EX.) Paper tape ESR10 EZP 5,000 (4mm Pitch) 1Ω = 1R00 (±1%) 1R0 (±5%) Paper tape ESR18 EZP 5,000 (4mm Pitch) 10Ω = 10R0 (±0.5%,±1%) 100 (±5%) Embossed tape ESR25 JZP 4,000 (4mm Pitch) 1MΩ = 1004 (±0.5%,± 1%) 105 (±5%) www.rohm.com 1/4 © 2016 ROHM Co., Ltd. All rights reserved. 2016.12 - Rev.G

ESR series 　 　 　 　 　 　 　 Datasheet Chip resistor dimensions and markings ● ■ESR01/03 ■ESR10/18/25 <Marking method> There are three or four digits used for the calculation number according to IEC code and "R" is used for the decimal point. (Unit:mm) Marking Part No. (mm) (inch) L W t a b existence +0.05 ESR01 1005 0402 1.00±0.05 0.50±0.05 0.35±0.05 0.20±0.10 0.25 No* -0.10 ESR03 1608 0603 1.60±0.10 0.80±0.10 0.45±0.10 0.30±0.20 0.30±0.20 No* ESR10 2012 0805 2.00±0.10 1.25±0.10 0.55±0.10 0.30±0.20 0.40±0.20 Yes ESR18 3216 1206 3.20±0.15 1.60±0.15 0.55±0.10 0.30±0.25 0.50±0.25 Yes ESR25 3225 1210 3.20±0.15 2.50±0.15 0.55±0.10 0.30±0.25 0.50±0.25 Yes *Only with spuare mark Land pattern example ● (Unit:mm) Dimensions A B C D Part No. ESR01 0.5 1.3 0.5 0.4 ESR03 1.0 2.0 0.8 0.5 ESR10 1.2 2.6 1.15 0.70 ESR18 2.2 4.0 1.5 0.9 ESR25 2.2 4.0 2.3 0.9 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 www.rohm.com 2/4 © 2016 ROHM Co., Ltd. All rights reserved. 2016.12 - Rev.G

ESR series 　 　 　 　 　 　 　 Datasheet Derating curve ● When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below. ■ESR 01 / 03 / 10 / 18 / 25 Characteristics ● Guaranteed balue Test items Test conditions Resistor ｔype Resistance See P.1 20℃ Variation of resistance See P.1 Measurement：+25/-55, +25/+125℃ with temperature Test voltage is the smaller one of ① or ② ①Rated voltage(current)×2.5,(ESR03/10/18/25) 2s Overload ±(2.0％＋0.1Ω) Rated voltage(current)×2.0,(ESR01) 2s ②Maximum overload voltage ※ A new uniform coating of minimum of Rosin-ethanol solution(25% weight) Solderability 　 95% of the surface being immersed and 　 Soldering condition：245±5℃ no soldering damage. Duration of immersion：2.0±0.5s Resistance to ±(1.0％＋0.05Ω) Soldering condition：260±5℃ soldering heat No remarkable abnormality on the appearance. Duration of immersion：10±1s Rapid change of temperature ±(1.0％＋0.05Ω) Test temp：-55℃～+125℃ 5cycle 40℃，93％(Relative humidity) Damp heat, steady state ±(3.0％＋0.1Ω) Test time：1,000h Rated voltage(current),70℃ Endurance at 70℃ ±(3.0％＋0.1Ω) 1.5h:ON－0.5h:OFF Test time：1,000h 155℃ Endurance ±(3.0％＋0.1Ω) Test time：1000h 23±5℃ _E0057 Resistance to solvent ±(1.0％＋0.05Ω) Solvent: 2-propanol Bend strength of ±(1.0％＋0.05Ω) - the end face plating Without mechanical damage such as breaks. EIAJ ED-4701/300 Test method 304 Voltage：2kV(ESR01) 　 3kV(ESR03/10/18) Static　electric ±(5.0％＋0.05Ω) 　 5kV(ESR25) characteristics C：100pF R：1.5kΩ Apply cycle：Times. Compliance Standard(s) : IEC60115-8 ※Maximum overload voltage (Test voltage) 　 　 　 　 　 JISC 5201-8 ESR01 ESR03 ESR10 ESR18 ESR25 100V 200V 200V 400V 400V 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 www.rohm.com 　 　　　　　　　　　 3/4 © 2016 ROHM Co., Ltd. All rights reserved. 2016.12 - Rev.G

ESR series 　 　 　 　 　 　 　 Datasheet 　 　 　 　 　　　　　　　 Tape dimensions ● ■Paper tape (Unit : mm) Part No. W F E A0 B0 ESR01 8.0±0.3 3.5±0.05 1.75±0.1 0.7±0.1 1.2±0.1 ESR03 8.0±0.3 3.5±0.05 1.75±0.1 1.1±0.1 1.9±0.1 +0.2 +0.2 ESR10 8.0±0.3 3.5±0.05 1.75±0.1 1.65 2.4 -0.1 -0.1 +0.1 +0.15 ESR18 8.0±0.3 3.5±0.05 1.75±0.1 1.95 3.5 -0.05 -0.05 Part No. D0 P0 P1 P2 T2 +0.1 ESR01 Φ1.5 4.0±0.1 2.0±0.05 2.0±0.05 MAX1.1 0 +0.1 ESR03 Φ1.5 4.0±0.1 4.0±0.1 2.0±0.05 MAX1.1 0 +0.1 ESR10 Φ1.5 4.0±0.1 4.0±0.1 2.0±0.05 MAX1.1 0 +0.1 ESR18 Φ1.5 4.0±0.1 4.0±0.1 2.0±0.05 MAX1.1 0 ■Embossed tape (Unit : mm) Part No. W F E A0 B0 8.0±0.3 3.5±0.05 1.75±0.1 3.0±0.1 3.5±0.1 ESR25 D0 P0 P1 P2 T2 +0.1 Φ1.5 4.0±0.1 4.0±0.1 2.0±0.05 MAX1.1 0 Reel dimensions ● (Unit : mm) Part No. A B C D ESR01 ESR03 0 +1 +1.0 ESR10 Φ180 Φ60 9 Φ13±0.2 -1.5 0 0 ESR18 ESR25 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 www.rohm.com 　 　　　　　　　　　 4/4 © 2016 ROHM Co., Ltd. All rights reserved. 2016.12 - Rev.G

Datasheet Notice Precaution on using ROHM Products 1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment(Note 1), aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 Notice-PAA-E Rev.001 © 2016 ROHM Co., Ltd. All rights reserved.

Datasheet 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreigntrade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 Notice-PAA-E Rev.001 © 2016 ROHM Co., Ltd. All rights reserved.

Datasheet 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising form the use of any ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this document not is current as of the issuing date and subject to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sales representative. 3. The information contained in this document is provided on an “as in” basis and ROHM does not warrant that all information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties resulting form inaccuracy or errors of or concerning such information. 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 Notice – WE Rev.001 © 2016 ROHM Co., Ltd. All rights reserved.

Datasheet ESR01MZPF - Web Page Distribution Inventory Part Number ESR01MZPF Package Unit Quantity 10000 Minimum Package Quantity 10000 Packing Type Taping Constitution Materials List inquiry RoHS Yes