DATASHEET EL5160, EL5161, EL5260, EL5261, EL5360 FN7387 200MHz Low-Power Current Feedback Amplifiers Rev 11.00 August 11, 2015 The EL5160, EL5161, EL5260, EL5261, and EL5360 are Features current feedback amplifiers with a bandwidth of 200MHz and operate from just 0.75mA supply current. This makes these • 200MHz -3dB bandwidth amplifiers ideal for today’s high speed video and monitor • 0.75mA supply current applications. • 1700V/µs slew rate With the ability to run from a single supply voltage from • Single and dual supply operation, from 5V to 10V supply span 5Vto10V, these amplifiers are ideal for handheld, portable, or battery-powered equipment. • Fast enable/disable (EL5160, EL5260 and EL5360 only) • Available in SOT-23 packages The EL5160, EL5260, and EL5360 also incorporate an enable and disable function to reduce the supply current to 14µA • Pb-Free (RoHS compliant) typical per amplifier. Allowing the CE pin to float or applying a Applications low logic level enables the corresponding amplifier. The EL5160 is available in the 6 Ld SOT-23 and 8 Ld SOIC • Battery-powered equipment packages, the EL5161 in 5 Ld SOT-23 package, the EL5260 in • Handheld, portable devices the 10 Ld MSOP package, the EL5261 in 8 Ld SOIC package, • Video amplifiers the EL5360 in 16 Ld SOIC and QSOP packages. All operate over the industrial temperature range of -40°C to +85°C. • Cable drivers • RGB amplifiers • Test equipment • Instrumentation • Current-to-voltage converters Pinouts EL5160 EL5160 EL5161 (8 LD SOIC) (6 LD SOT-23) (5 LD SOT-23) TOP VIEW TOP VIEW TOP VIEW NC 1 8 CE OUT 1 6 VS+ OUT 1 5 VS+ IN- 2 7 VS+ VS- 2 5 CE VS- 2 - + - + - + IN+ 3 6 OUT IN+ 3 4 IN- IN+ 3 4 IN- VS- 4 5 NC EL5260 EL5261 EL5360 (10 LD MSOP) (8 LD SOIC) (16 LD SOIC, QSOP) TOP VIEW TOP VIEW TOP VIEW OUT 1 10VS+ OUTA 1 8 VS+ INA+ 1 16INA- - IN- 2 9 OUT INA- 2 7 OUTB CEA 2 15OUTA - - + + + IN+ 3 8 IN- INA+ 3 6 INB- VS- 3 14VS+ - - + + + VS- 4 77 IN+ VS- 4 5 INB+ CEB 4 13OUTB - CE 5 6 CE INB+ 5 12INB- NC 6 11 NC + CEC 7 10OUTC - INC+ 8 9 INC- FN7387 Rev 11.00 Page 1 of 17 August 11, 2015

EL5160, EL5161, EL5260, EL5261, EL5360 Ordering Information PART NUMBER PACKAGE PKG. (Notes 2, 3) PART MARKING TAPE & REEL (Pb-free) DWG. # EL5160ISZ 5160ISZ - 8 Ld SOIC (150 mil) M8.15E EL5160ISZ-T7 (Note 1) 5160ISZ 7” 8 Ld SOIC (150 mil) M8.15E EL5160ISZ-T7A (Note 1) 5160ISZ 7” 8 Ld SOIC (150 mil) M8.15E EL5160ISZ-T13 (Note 1) 5160ISZ 13” 8 Ld SOIC (150 mil) M8.15E EL5160IWZ-T7 (Note 1) BAAN (Note 4) 7” (3k pcs) 6 Ld SOT-23 P6.064A EL5160IWZ-T7A (Note 1) BAAN (Note 4) 7” (250 pcs) 6 Ld SOT-23 P6.064A EL5161IWZ-T7 (Note 1) BAJA (Note 4) 7” (3k pcs) 5 Ld SOT-23 P6.064A EL5161IWZ-T7A (Note 1) BAJA (Note 4) 7” (250 pcs) 5 Ld SOT-23 P6.064A EL5260IYZ BAAAK - 10 Ld MSOP (3.0mm) M10.118A (No longer available or supported) EL5260IYZ-T7 (Note 1) BAAAK 7” 10 Ld MSOP (3.0mm) M10.118A (No longer available or supported) EL5260IYZ-T13 (Note 1) BAAAK 13” 10 Ld MSOP (3.0mm) M10.118A (No longer available or supported) EL5261ISZ 5261ISZ - 8 Ld SOIC (150 mil) M8.15E (No longer available or supported) EL5261ISZ-T7 (Note 1) 5261ISZ 7” 8 Ld SOIC (150 mil) M8.15E (No longer available or supported) EL5261ISZ-T13 (Note 1) 5261ISZ 13” 8 Ld SOIC (150 mil) M8.15E (No longer available or supported) EL5360ISZ EL5360ISZ - 16 Ld SOIC (150 mil) MDP0027 (No longer available or supported) EL5360ISZ-T7 (Note 1) EL5360ISZ 7” 16 Ld SOIC (150 mil) MDP0027 (No longer available or supported) EL5360ISZ-T13 (Note 1) EL5360ISZ 13” 16 Ld SOIC (150 mil) MDP0027 (No longer available or supported) EL5360IUZ(No longer available or 5360IUZ - 16 Ld QSOP (150 mil) MDP0040 supported) EL5360IUZ-T7 (Note 1) 5360IUZ 7” 16 Ld QSOP (150 mil) MDP0040 (No longer available or supported) EL5360IUZ-T13 (Note 1) 5360IUZ 13” 16 Ld QSOP (150 mil) MDP0040 (No longer available or supported) NOTES: 1. Please refer to TB347 for details on reel specifications. 2. Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see product information page for EL5160, EL5161, EL5260, EL5261, EL5360. For more information on MSL, please see tech brief TB363. 4. The part marking is located on the bottom of the part. FN7387 Rev 11.00 Page 2 of 17 August 11, 2015

EL5160, EL5161, EL5260, EL5261, EL5360 3Absolute Maximum Ratings Thermal Information (TA = +25°C) Supply Voltage between VS+ and VS-. . . . . . . . . . . . . . . . . . . . . . . . . . 13.2V Maximum Operating Junction Temperature. . . . . . . . . . . . . . . . . . +125°C Maximum Continuous Output Current. . . . . . . . . . . . . . . . . . . . . . . . . 50mA Maximum Power Dissipation . . . . . . . . . . . . . . . . . . . see curves on page7 Slew Rate of VS+ to VS- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1V/µs Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to +150°C Pin Voltages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . (VS-) - 0.5V to (VS+) + 0.5V Ambient Operating Temperature Range. . . . . . . . . . . . . . -40°C to +85°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Electrical Specifications VS+ = +5V, VS- = -5V, RF = 750Ω for AV = 1, RL = 150Ω, VCE, H = VS+, VCE, L = (VS+) -3V, TA = +25°C, Unless Otherwise Specified. Boldface limits apply across the operating temperature range, -40°C to +85°C. MIN MAX PARAMETER DESCRIPTION CONDITIONS (Note 6) TYP (Note 6) UNIT AC PERFORMANCE BW -3dB Bandwidth AV = +1, RL = 500Ω 200 MHz AV = +2, RL = 150Ω 125 MHz BW1 0.1dB Bandwidth RL = 100Ω 10 MHz SR Slew Rate VO = -2.5V to +2.5V, AV = +2, RF = RG = 1kΩ, 900 1700 2500 V/µs RL= 100Ω EL5260, EL5261 800 1300 2500 V/µs SR 500Ω Load 1360 V/µs tS 0.1% Settling Time VOUT = -2.5V to +2.5V, AV = +2 35 ns eN Input Voltage Noise 4 nV/√Hz iN- IN- Input Current Noise 7 pA/√Hz iN+ IN+ Input Current Noise 8 pA/√Hz HD2 5MHz, 2.5VP-P, RL = 150Ω, AV = +2 -74 dBc HD3 5MHz, 2.5VP-P, RL = 150Ω, AV = +2 -50 dBc dG Differential Gain Error (Note 5) AV = +2 0.1 % dP Differential Phase Error (Note 5) AV = +2 0.1 ° DC PERFORMANCE VOS Offset Voltage -5 1.6 +5 mV TCVOS Input Offset Voltage Temperature Measured from TMIN to TMAX 6 µV/°C Coefficient ROL Open Loop Transimpedance Gain ±2.5VOUT into 150Ω 800 2000 kΩ INPUT CHARACTERISTICS CMIR Common Mode Input Range Guaranteed by CMRR test ±3 ±3.3 V CMRR Common Mode Rejection Ratio VIN = ±3V 50 62 75 dB -ICMR - Input Current Common Mode Rejection -1 +1 µA/V +IIN + Input Current -4 +4 µA -IIN - Input Current -5 +5 µA RIN Input Resistance 1.5 4 15 MΩ CIN Input Capacitance 1 pF FN7387 Rev 11.00 Page 3 of 17 August 11, 2015

EL5160, EL5161, EL5260, EL5261, EL5360 Electrical Specifications VS+ = +5V, VS- = -5V, RF = 750Ω for AV = 1, RL = 150Ω, VCE, H = VS+, VCE, L = (VS+) -3V, TA = +25°C, Unless Otherwise Specified. Boldface limits apply across the operating temperature range, -40°C to +85°C. (Continued) MIN MAX PARAMETER DESCRIPTION CONDITIONS (Note 6) TYP (Note 6) UNIT OUTPUT CHARACTERISTICS VO Output Voltage Swing RL = 150Ω to GND ±3.1 ±3.4 ±3.8 V RL = 1kΩ to GND ±3.8 ±4.0 ±4.2 V IOUT Output Current RL = 10Ω to GND 40 70 140 mA SUPPLY ISON Supply Current - Enabled, per Amplifier No load, VIN = 0V (EL5160, EL5161, EL5260, 0.6 0.75 0.85 mA EL5261) No load, VIN = 0V (EL5360) 0.6 0.8 0.92 mA ISOFF+ Supply Current - Disabled, per Amplifier No load, VIN = 0V, Only EL5160, EL5260, 0 10 25 µA EL5360 ISOFF- Supply Current - Disabled, per Amplifier -25 -14 0 µA PSRR Power Supply Rejection Ratio DC, VS = ±4.75V to ±5.25V 65 74 dB -IPSR - Input Current Power Supply Rejection DC, VS = ±4.75V to ±5.25V -0.5 0.1 0.5 µA/V ENABLE (EL5160, EL5260, EL5360 ONLY) tEN Enable Time 600 ns tDIS Disable Time 800 ns ICE, H CE Pin Input High Current CE = VS+ 1 5 25 µA ICE, L CE Pin Input Low Current CE = (VS+) - 5V -1 0 1 µA NOTE: 5. Standard NTSC test, AC signal amplitude = 286mVP-P, f = 3.58MHz. 6. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design. Typical Performance Curves 3 4 B) 1 B) 2 d d N ( N ( GAI -1 GAI 0 D D E E Z Z ALI -3 VS+ = +5V ALI -2 ORM VRSL -= = 1 -550VΩ ORM VVSS+- == -+55VV N -5 AV = 2 N -4 AV = 1 RF = 806Ω RL = 500Ω RG = 806Ω RF = 2800Ω -7 -6 100k 1M 10M 100M 1G 100k 1M 10M 100M 1G FREQUENCY (Hz) FREQUENCY (Hz) FIGURE 1. FREQUENCY RESPONSE (AV = +2) FIGURE 2. FREQUENCY RESPONSE (AV = +1) FN7387 Rev 11.00 Page 4 of 17 August 11, 2015

EL5160, EL5161, EL5260, EL5261, EL5360 Typical Performance Curves (Continued) 5 4 RL = 500Ω AV = 2 RF = 2.7kΩ RL=150Ω B) 3 AV = 1 B) 2 RF = RG = 762Ω d d N ( ±5V N ( ±5V GAI 1 GAI 0 ED ±4V ±6V ED ±4V Z Z LI -1 LI -2 ±3V A ±3V A RM ±2.5V RM ±6V NO -3 NO -4 ±2.5V -5 -6 100k 1M 10M 100M 1G 100k 1M 10M 100M 1G FREQUENCY (Hz) FREQUENCY (Hz) FIGURE 3. FREQUENCY RESPONSE FOR VARIOUS ±VS FIGURE 4. FREQUENCY RESPONSE FOR VARIOUS SUPPLY VOLTAGES 4 10M VS+ = +5V VS- = -5V GAIN (dB) 20 ARRVLF === 55106000ΩΩ ANCE (Ω) 1010Mk ED ED 10k Z P MALI -2 NSIM 1k R A O R N -4 T 100 -6 10 100k 1M 10M 100M 1G 1k 10k 100k 1M 10M 100M 1G FREQUENCY (Hz) FREQUENCY (Hz) FIGURE 5. FREQUENCY RESPONSE (AV = +10) FIGURE 6. OPEN LOOP TRANSIMPEDANCE GAIN vs FREQUENCY (ROL) OUTPUT INPUT 500mV/DIV 1V/DIV INPUT OUTPUT 1V/DIV 500mV/DIV VVARRVSSLF +- === == 2R1 -+55G05V Ω=V 422Ω VVARRVSSLF +- === == 2R1 -+55G05V Ω=V 422Ω 4ns/DIV 4ns/DIV FIGURE 7. OUTPUT RISE TIME FIGURE 8. OUTPUT FALL TIME FN7387 Rev 11.00 Page 5 of 17 August 11, 2015

EL5160, EL5161, EL5260, EL5261, EL5360 Typical Performance Curves (Continued) VVSS+- == -+55VV CE 5V/DIV 5V/DIV CE 200mV/DIV VOUT 200mV/DIV VOUT VS+ = +5V VS- = -5V 400ns/DIV 400ns/DIV FIGURE 9. DISABLE DELAY TIME FIGURE 10. ENABLE DELAY TIME 0 1K VS+ = +5V VS+ = +5V VS- = -5V VS- = -5V -20 Ω) 100 E ( C B) -40 VS+ AN 10 d D R ( PE R M PS -60 VS- T I 1 U P T -80 OU100m -100 10m 1k 10k 100k 1M 10M 100M 1G 10k 100k 1M 10M 100M FREQUENCY (Hz) FREQUENCY (Hz) FIGURE 11. PSRR vs FREQUENCY FIGURE 12. CLOSED LOOP OUTPUT IMPEDANCE vs FREQUENCY 4 4 VS = ±5V VS = ±5V RG = 750Ω AV = -1 B) 2 RL = 150Ω B) 2 RL = 150Ω RF = 768Ω d d N ( N ( GAI 0 GAI 0 ZED AV = -2 ZED RF = 1kΩ ALI -2 AV = -5 AV = +2 ALI -2 M M R R RF = 1.2kΩ O O N -4 N -4 RF = 1.5kΩ -6 -6 100k 1M 10M 100M 1G 100k 1M 10M 100M 1G FREQUENCY (Hz) FREQUENCY (Hz) FIGURE 13. FREQUENCY RESPONSE FOR VARIOUS GAIN FIGURE 14. FREQUENCY RESPONSE FOR VARIOUS FEEDBACK SETTINGS RESISTORS, AV = -1 FN7387 Rev 11.00 Page 6 of 17 August 11, 2015

EL5160, EL5161, EL5260, EL5261, EL5360 Typical Performance Curves (Continued) 4 5 VS = ±5V VS = ±5V B) 2 RRFL == 570608ΩΩ AV = -5 B) 3 ARVL == +1510Ω RF = 750Ω d d N ( AV = -1 N ( RF = 1kΩ GAI 0 GAI 1 D D ZE AV = +5 ZE LI -2 LI -1 RF = 2.8kΩ A A M M OR AV = +10 OR N -4 N -3 -6 -5 100k 1M 10M 100M 1G 100k 1M 10M 100M 1G FREQUENCY (Hz) FREQUENCY (Hz) FIGURE 15. FREQUENCY RESPONSE FOR VARIOUS GAIN FIGURE 16. FREQUENCY RESPONSE FOR VARIOUS FEEDBACK SETTINGS RESISTORS, AV = +1 JEDEC JESD51-7 HIGH EFFECTIVE THERMAL JEDEC JESD51-7 HIGH EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD CONDUCTIVITY TEST BOARD 1.4 1.4 1.250W 1.2 1.2 W) SO16 (0.150”) W) N ( 1 909mW JA = 80°C/W N ( 1 893mW O O TI TI A 0.8 SO8 A 0.8 870mW QSOP16 P P SI JA = 110°C/W SI JA=112°C/W DIS 0.6 DIS 0.6 R 435mW R MSOP10 WE 0.4 WE 0.4 JA=115°C/W O O P 0.2 SOT23-5/6 P 0.2 JA = 110°C/W 0 0 0 25 50 75 85 100 125 150 0 25 50 7585 100 125 150 FREQUENCY (Hz) FREQUENCY (Hz) FIGURE 17. PACKAGE POWER DISSIPATION vs AMBIENT FIGURE 18. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE TEMPERATURE JEDEC JESD51-3 LOW EFFECTIVE THERMAL JEDEC JESD51-3 LOW EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD CONDUCTIVITY TEST BOARD 1 1.2 0.9 SO16 (0.150”) W) 0.8 909mW JA = 110°C/W W) 1 ON ( 0.7 ON ( 0.8 WER DISSIPATI 0000....4635 632951mmWW JA =S 1O680°C/W WER DISSIPATI 00..46 643836mmWWMSOP10JAQ =S 1O5P81°6C/W PO 0.2 SOT23-5/6 PO 0.2 JA = 206°C/W 0.1 JA = 256°C/W 0 0 0 25 50 75 85 100 125 150 0 25 50 7585 100 125 150 FREQUENCY (Hz) FREQUENCY (Hz) FIGURE 19. PACKAGE POWER DISSIPATION vs AMBIENT FIGURE 20. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE TEMPERATURE FN7387 Rev 11.00 Page 7 of 17 August 11, 2015

EL5160, EL5161, EL5260, EL5261, EL5360 Pin Descriptions EL5160 EL5160 PIN (8 Ld SOIC) (6 Ld SOT-23) EL5161 EL5260 EL5261 EL5360 NAME FUNCTION EQUIVALENT CIRCUIT 1, 5 - - - - 6, 11 NC Not connected 2 4 4 2, 8 2, 6 9, 12, 16 IN- Inverting input VS+ IN+ IN- VS- Circuit 1 3 3 3 3, 7 3, 5 1, 5, 8 IN+ Non-inverting input (See circuit 1) 4 2 2 4 4 3 VS- Negative supply 6 1 1 1, 9 1, 7 10, 13, 15 OUT Output VS+ OUT VS- Circuit 2 7 6 5 10 8 14 VS+ Positive supply 8 5 - 5, 6 - 2, 4, 7 CE Chip enable VS+ CE VS- Circuit 3 Applications Information Power Supply Bypassing and Printed Circuit Board Layout Product Description As with any high frequency device, good printed circuit board The EL5160, EL5161, EL5260, EL5261, and EL5360 are low layout is necessary for optimum performance. Low impedance power, current-feedback operational amplifiers that offer a wide ground plane construction is essential. Surface mount -3dB bandwidth of 200MHz and a low supply current of 0.75mA components are recommended, but if leaded components are per amplifier. The EL5160, EL5161, EL5260, EL5261, and used, lead lengths should be as short as possible. The power EL5360 work with supply voltages ranging from a single 5V to supply pins must be well bypassed to reduce the risk of 10V and they are also capable of swinging to within 1V of either oscillation. The combination of a 4.7µF tantalum capacitor in supply on the output. Because of their current-feedback topology, parallel with a 0.01µF capacitor has been shown to work well the EL5160, EL5161, EL5260, EL5261, and EL5360 do not when placed at each supply pin. havethe normal gain-bandwidth product associated with For good AC performance, parasitic capacitance should be kept voltage-feedback operational amplifiers. Instead, their -3dB to a minimum, especially at the inverting input. (See the bandwidth remains relatively constant as closed-loop gain is “Capacitance at the Inverting Input” section) Even when ground increased. This combination of high bandwidth and low power, plane construction is used, it should be removed from the area together with aggressive pricing make the EL5160, EL5161, near the inverting input to minimize any stray capacitance at that EL5260, EL5261, and EL5360 ideal choices for many node. Carbon or Metal-Film resistors are acceptable with the low-power/high-bandwidth applications such as portable, Metal-Film resistors giving slightly less peaking and bandwidth handheld, or battery-powered equipment. because of additional series inductance. Use of sockets, particularly for the SO package, should be avoided if possible. Sockets add parasitic inductance and capacitance which results in additional peaking and overshoot. FN7387 Rev 11.00 Page 8 of 17 August 11, 2015

EL5160, EL5161, EL5260, EL5261, EL5360 Disable/Power-Down Supply Voltage Range and Single-Supply Operation The EL5160, EL5260, EL5360 amplifiers can be disabled, placing the output in a high impedance state. When disabled, the The EL5160, EL5161, EL5260, EL5261, and EL5360 have been amplifier supply current reduces to <15µA. The amplifiers designed to operate with supply voltages having a span of 5V to disable when their CE pin is pulled up to within 1V of the positive 10V. In practical terms, this means that they will operate on dual supply. Similarly, the amplifier is enabled by floating or pulling its supplies ranging from ±2.5V to ±5V. With single-supply, the CE pin to at least 3V below the positive supply. For a ±5V supply, EL5160, EL5161, EL5260, EL5261, and EL5360 will operate this means that an amplifier is enabled when CE is 2V or less, from 5V to 10V. and disabled when CE is above 4V. Although the logic levels are not standard TTL, this choice of logic voltages allows an amplifier As supply voltages continue to decrease, it becomes necessary to to be enabled by tying CE to ground, even in 5V single supply provide input and output voltage ranges that can get as close as applications. The CE pin can be driven from CMOS outputs. possible to the supply voltages. The EL5160, EL5161, EL5260, EL5261, and EL5360 have an input range which extends to Capacitance at the Inverting Input within 2V of either supply. So, for example, with ±5V supplies, the EL5160, EL5161, EL5260, EL5261, and EL5360 have an input Any manufacturer’s high-speed voltage- or current-feedback range which spans ±3V. The output range of the EL5160, amplifier can be affected by stray capacitance at the inverting EL5161, EL5260, EL5261, and EL5360 is also quite large, input. For inverting gains, this parasitic capacitance has little extending to within 1V of the supply rail. On a ±5V supply, the effect because the inverting input is a virtual ground, but for output is therefore capable of swinging from -4V to +4V. non-inverting gains, this capacitance (in conjunction with the Single-supply output range is larger because of the increased feedback and gain resistors) creates a pole in the feedback path negative swing due to the external pull-down resistor to ground. of the amplifier. This pole, if low enough in frequency, has the same destabilizing effect as a zero in the forward open-loop Video Performance response. The use of large-value feedback and gain resistors exacerbates the problem by further lowering the pole frequency For good video performance, an amplifier is required to maintain (increasing the possibility of oscillation.) the same output impedance and the same frequency response as DC levels are changed at the output. This is especially difficult The EL5160, EL5161, EL5260, EL5261, and EL5360 are when driving a standard video load of 150Ω, because of the optimized for an 806Ω (AV = +2) feedback resistor. With the high change in output current with DC level. Previously, good bandwidth of these amplifiers, these resistor values might cause differential gain could only be achieved by running high idle stability problems when combined with parasitic capacitance, currents through the output transistors (to reduce variations in thus ground plane is not recommended around the inverting output impedance.) These currents were typically comparable to input pin of the amplifier. the entire 1mA supply current of each EL5160, EL5161, EL5260, EL5261, and EL5360 amplifier. Special circuitry has been Feedback Resistor Values incorporated in the EL5160, EL5161, EL5260, EL5261, and The EL5160, EL5161, EL5260, EL5261, and EL5360 have been EL5360 to reduce the variation of output impedance with current designed and specified at a gain of +2 with RF approximately output. This results in dG and dP specifications of 0.1% and 0.1°, 806. This value of feedback resistor gives 125MHz of -3dB while driving 150Ω at a gain of 2. bandwidth at AV = 2 with 1dB of peaking. Since the EL5160, Video performance has also been measured with a 500Ω load at EL5161, EL5260, EL5261, and EL5360 are current-feedback a gain of +1. Under these conditions, the EL5160 has dG and dP amplifiers, it is also possible to change the value of RF to get specifications of 0.1% and 0.1°. more bandwidth. As seen in the curve of Frequency Response for Various RF and RG on page5, bandwidth and peaking can be Output Drive Capability easily modified by varying the value of the feedback resistor. In spite of their low 1mA per amplifier supply current, the Because the EL5160, EL5161, EL5260, EL5261, and EL5360 are EL5160, EL5161, EL5260, EL5261, and EL5360 are capable of current-feedback amplifiers, their gain-bandwidth product is not providing a minimum of ±40mA of output current. With a a constant for different closed-loop gains. This feature actually minimum of ±40mA of output drive, the EL5160 is capable of allows the EL5160, EL5161, EL5260, EL5261, and EL5360 to driving 50Ω loads to both rails, making it an excellent choice for maintain about the same -3dB bandwidth. As gain is increased, driving isolation transformers in telecommunications bandwidth decreases slightly while stability increases. Since the applications. loop stability is improving with higher closed-loop gains, it becomes possible to reduce the value of RF below the specified 806Ω value and still retain stability, resulting in only a slight loss of bandwidth with increased closed-loop gain. FN7387 Rev 11.00 Page 9 of 17 August 11, 2015

EL5160, EL5161, EL5260, EL5261, EL5360 Driving Cables and Capacitive Loads Typical Application Circuits When used as a cable driver, double termination is always recommended for reflection-free performance. For those 0.1µF +5V applications, the back-termination series resistor will decouple the EL5160, EL5161, EL5260, EL5261, and EL5360 from the IN+ VS+ OUT cable and allow extensive capacitive drive. However, other IN- applications may have high capacitive loads without a VS- back-termination resistor. In these applications, a small series 0.1µF -5V resistor (usually between 5Ω and 50Ω) can be placed in series 500Ω 5Ω with the output to eliminate most peaking. The gain resistor (RG) can then be chosen to make up for any gain loss which may be created by this additional resistor at the output. In many cases it is also possible to simply increase the value of the feedback +5V 0.1µF VOUT resistor (RF) to reduce the peaking. Current Limiting IN+ VS+ OUT 5Ω IN- The EL5160, EL5161, EL5260, EL5261, and EL5360 have no VS- 0.1µF internal current-limiting circuitry. If the output is shorted, it is -5V possible to exceed the Absolute Maximum Rating for output 500Ω 500Ω current or power dissipation, potentially resulting in the VIN destruction of the device. FIGURE 21. INVERTING 200mA OUTPUT CURRENT DISTRIBUTION AMPLIFIER Power Dissipation With the high output drive capability of the EL5160, EL5161, EL5260, EL5261, and EL5360, it is possible to exceed the 500Ω 500Ω +125°C Absolute Maximum junction temperature under certain very high load current conditions. Generally speaking when RL 0.1µF +5V falls below about 25Ω, it is important to calculate the maximum junction temperature (TJMAX) for the application to determine if IN+ VS+ power supply voltages, load conditions, or package type need to OUT IN- be modified for the EL5160, EL5161, EL5260, EL5261, and VS- EL5360 to remain in the safe operating area. These parameters 0.1µF 500Ω -5V are calculated as follows: T = T + nPD  JMAX MAX JA MAX 0.1µF 500Ω +5V where: VIN IN+ VS+ OUT • TMAX = Maximum ambient temperature IN- VOUT VS- •JA = Thermal resistance of the package 0.1µF -5V • n = Number of amplifiers in the package FIGURE 22. FAST-SETTLING PRECISION AMPLIFIER • PDMAX = Maximum power dissipation of each amplifier in the package PDMAX for each amplifier can be calculated as follows: V OUTMAX PD = 2V I + V –V ---------------------------- MAX S SMAX S OUTMAX R L where: • VS = Supply voltage • ISMAX = Maximum supply current of 0.85mA • VOUTMAX = Maximum output voltage (required) • RL = Load resistance FN7387 Rev 11.00 Page 10 of 17 August 11, 2015

EL5160, EL5161, EL5260, EL5261, EL5360 0.1µF 0.1µF +5V +5V IN+ VS+ IN+ VS+ OUT OUT IN- IN- VS- VS- 0.1µF 0.1µF -5V -5V 0.1µF 500Ω 250Ω 500Ω 500Ω VOUT+ 0.1µF 1kΩ +5V 240Ω 0.1µF +5V IINN+- VS+ OUT 250Ω VOUT- 0.1µF IN+ VS+ OUT VS- 1kΩ IN- VOUT 0.1µF VS- -5V 0.1µF 500Ω 500Ω -5V VIN 500Ω 500Ω TRANSMITTER RECEIVER FIGURE 23. DIFFERENTIAL LINE DRIVER/RECEIVER Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make sure that you have the latest revision. DATE REVISION CHANGE August 11, 2015 FN7387.11 Updated Ordering Information table on page2. Added Revision History and About Intersil sections. About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask. Reliability reports are also available from our website at www.intersil.com/support FN7387 Rev 11.00 Page 11 of 17 August 11, 2015

EL5160, EL5161, EL5260, EL5261, EL5360 Small Outline Package Family (SO) A D h X 45° NN (N/2)+1 A PIN #1 I.D. MARK E E1 c SEE DETAIL “X” 1 (N/2) B L1 0.010M C A B e H C A2 GAUGE SEATING PLANE 0.010 PLANE A1 L 4° ±4° 0.004 C 0.010M C A B b DETAIL X MDP0027 SMALL OUTLINE PACKAGE FAMILY (SO) INCHES SO16 SO16 (0.300”) SO20 SO24 SO28 SYMBOL SO-8 SO-14 (0.150”) (SOL-16) (SOL-20) (SOL-24) (SOL-28) TOLERANCE NOTES A 0.068 0.068 0.068 0.104 0.104 0.104 0.104 MAX - A1 0.006 0.006 0.006 0.007 0.007 0.007 0.007 0.003 - A2 0.057 0.057 0.057 0.092 0.092 0.092 0.092 0.002 - b 0.017 0.017 0.017 0.017 0.017 0.017 0.017 0.003 - c 0.009 0.009 0.009 0.011 0.011 0.011 0.011 0.001 - D 0.193 0.341 0.390 0.406 0.504 0.606 0.704 0.004 1, 3 E 0.236 0.236 0.236 0.406 0.406 0.406 0.406 0.008 - E1 0.154 0.154 0.154 0.295 0.295 0.295 0.295 0.004 2, 3 e 0.050 0.050 0.050 0.050 0.050 0.050 0.050 Basic - L 0.025 0.025 0.025 0.030 0.030 0.030 0.030 0.009 - L1 0.041 0.041 0.041 0.056 0.056 0.056 0.056 Basic - h 0.013 0.013 0.013 0.020 0.020 0.020 0.020 Reference - N 8 14 16 16 20 24 28 Reference - Rev. M 2/07 NOTES: 1. Plastic or metal protrusions of 0.006” maximum per side are not included. 2. Plastic interlead protrusions of 0.010” maximum per side are not included. 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994 FN7387 Rev 11.00 Page 12 of 17 August 11, 2015

EL5160, EL5161, EL5260, EL5261, EL5360 Package Outline Drawing P6.064A 6 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE Rev 0, 2/10 1.90 0-3° 0.95 D 0.08-0.20 A 6 5 4 PIN 1 INDEX AREA 2.80 3 1.60 3 5 0.15 C D 2x (0.60) 1 2 3 0.20 C 2x SEE DETAIL X B 0.40 ±0.05 3 0.20 M C A-B D TOP VIEW END VIEW 10° TYP 5 0.15 C A-B (2 PLCS) 2.90 2x H 1.14 ±0.15 1.45 MAX C (0.25) GAUGE 0.10 C SEATING PLANE PLANE 0.05-0.15 SIDE VIEW DETAIL "X" 0.45±0.1 4 (0.60) (1.20) NOTES: (2.40) 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to ASME Y14.5M-1994. 3. Dimension is exclusive of mold flash, protrusions or gate burrs. 4. Foot length is measured at reference to guage plane. 5. This dimension is measured at Datum “H”. 6. Package conforms to JEDEC MO-178AA. (0.95) (1.90) TYPICAL RECOMMENDED LAND PATTERN FN7387 Rev 11.00 Page 13 of 17 August 11, 2015

EL5160, EL5161, EL5260, EL5261, EL5360 Package Outline Drawing P5.064A 5 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE Rev 0, 2/10 1.90 0-3° D A 0.08-0.20 5 4 PIN 1 INDEX AREA 2.80 3 1.60 3 5 0.15 CD 2x 2 0.20 C (0.60) 2x 0.95 SEE DETAIL X B 0.40 ±0.05 3 END VIEW 0.20M C A-B D TOP VIEW 10° TYP (2 PLCS) 5 0.15 C A-B H 2.90 2x 1.45 MAX C 1.14 ±0.15 (0.25)GAUGE 0.10 C SEATING PLANE PLANE 0.45±0.1 4 SIDE VIEW 0.05-0.15 DETAIL "X" (0.60) (1.20) NOTES: 1. Dimensions are in millimeters. (2.40) Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to ASME Y14.5M-1994. 3. Dimension is exclusive of mold flash, protrusions or gate burrs. 4. Foot length is measured at reference to guage plane. 5. This dimension is measured at Datum “H”. 6. Package conforms to JEDEC MO-178AA. (0.95) (1.90) TYPICAL RECOMMENDED LAND PATTERN FN7387 Rev 11.00 Page 14 of 17 August 11, 2015

EL5160, EL5161, EL5260, EL5261, EL5360 Package Outline Drawing M8.15E 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE Rev 0, 08/09 4 4.90 ± 0.10 A DETAIL "A" 0.22 ± 0.03 B 6.0 ± 0.20 3.90 ± 0.10 4 PIN NO.1 ID MARK 5 (0.35) x 45° 4° ± 4° 0.43 ± 0.076 1.27 0.25MC AB SIDE VIEW “B” TOP VIEW 1.75 MAX 1.45 ± 0.1 0.25 GAUGE PLANE C 0.175 ± 0.075 SEATING PLANE 0.10C SIDE VIEW “A 0.63 ±0.23 DETAIL "A" (1.27) (0.60) NOTES: (1.50) 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal ± 0.05 (5.40) 4. Dimension does not include interlead flash or protrusions. Interlead flash or protrusions shall not exceed 0.25mm per side. 5. The pin #1 identifier may be either a mold or mark feature. 6. Reference to JEDEC MS-012. TYPICAL RECOMMENDED LAND PATTERN FN7387 Rev 11.00 Page 15 of 17 August 11, 2015

EL5160, EL5161, EL5260, EL5261, EL5360 Package Outline Drawing M10.118A (JEDEC MO-187-BA) 10 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE (MSOP) Rev 0, 9/09 A 3.0 ± 0.1 10 0.25 CAB DETAIL "X" 1.10 Max SIDE VIEW 2 0.18 ± 0.05 3.0 ± 0.1 4.9 ± 0.15 PIN# 1 ID B 1 2 0.95 BSC 0.5 BSC TOP VIEW Gauge Plane H 0.86 ± 0.09 0.25 C SEATING PLANE 3°±3° 0.55 ± 0.15 0.10 ± 0.05 0.23 +0.07/ -0.08 0.10C 0.08 CAB DETAIL "X" SIDE VIEW 1 5.80 4.40 NOTES: 3.00 1. Dimensions are in millimeters. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 0.50 3. Plastic or metal protrusions of 0.15mm max per side are not included. 4. Plastic interlead protrusions of 0.25mm max per side are not 0.30 included. 1.40 5. Dimensions “D” and “E1” are measured at Datum Plane “H”. TYPICAL RECOMMENDED LAND PATTERN 6. This replaces existing drawing # MDP0043 MSOP10L. FN7387 Rev 11.00 Page 16 of 17 August 11, 2015

EL5160, EL5161, EL5260, EL5261, EL5360 Quarter Size Outline Plastic Packages Family (QSOP) A MDP0040 D QUARTER SIZE OUTLINE PLASTIC PACKAGES FAMILY N (N/2)+1 INCHES SYMBOL QSOP16 QSOP24 QSOP28 TOLERANCE NOTES A 0.068 0.068 0.068 Max. - PIN #1 I.D. MARK E E1 A1 0.006 0.006 0.006 ±0.002 - A2 0.056 0.056 0.056 ±0.004 - b 0.010 0.010 0.010 ±0.002 - 1 (N/2) c 0.008 0.008 0.008 ±0.001 - B D 0.193 0.341 0.390 ±0.004 1, 3 0.010 CAB E 0.236 0.236 0.236 ±0.008 - e E1 0.154 0.154 0.154 ±0.004 2, 3 H e 0.025 0.025 0.025 Basic - C SEATING L 0.025 0.025 0.025 ±0.009 - PLANE L1 0.041 0.041 0.041 Basic - 0.004 C 0.007 CAB b N 16 24 28 Reference - Rev. F 2/07 L1 NOTES: 1. Plastic or metal protrusions of 0.006” maximum per side are not A included. 2. Plastic interlead protrusions of 0.010” maximum per side are not c included. SEE DETAIL "X" 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994. 0.010 A2 GAUGE PLANE L A1 4°±4° DETAIL X © Copyright Intersil Americas LLC 2004-2015. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN7387 Rev 11.00 Page 17 of 17 August 11, 2015