50-150 Watts C xppower.com D DLG Series - C A • AC Input LED Driver • Constant Voltage & Current Operation • High Power Factor • High Efficiency • Water Proof to IP67 • 90-305 VAC Input Voltage Range • 3 Year Warranty Specification Input General Input Voltage • 90-305 VAC, see derating curve Efficiency • See table Input Frequency • 47-63 Hz Isolation • 3750 VAC Input to Output Input Current • 50 W: 1.0 A at 115 VAC, 0.5 A at 230 VAC, 1880 VAC Input to Ground 75 W: 1.2 A at 115 VAC, 0.6 A at 230 VAC, 500 VAC Output to Ground 100 W: 1.4 A at 115 VAC, 0.7 A at 230 VAC, Switching Frequency • DLG50/75: 40-80 kHz 150 W: 2.0 A at 115 VAC, 1.0 A at 230 VAC DLG100/150: PWM 60-80 kHz, Inrush Current • 65 A at 230 VAC, cold start +25 °C PFC 55-133 kHz Power Factor • >0.94 at 230 VAC, full load MTBF • >200kHrs to MIL-HDBK-217F at 25°C, GB Earth Leakage Current • DLG50/75: 500 µA max at 230 VAC DLG100/150: 750 µA max at 230 VAC Environmental No Load Input Power • DLG100: 0.5 W max at 230 VAC Operating Temperature • DLG50/75: -40 °C to +60 °C Other models: 0.6 W max at 230 VAC (see derating curve), Input Protection • DLG50/75 T2.5A/300V fuse fitted in line, DLG100/150: -30 °C to +70 °C DLG100 T3.15A/300V fuse fitted in line, (see derating curve) DLG150 T4A/300V fuse fitted in line Operating Humidity • 5-100% RH, non-condensing Storage Temperature • -40 °C to +80 °C Output Operating Altitude • 3000 m Vibration • 10-500 Hz, 2 g, 10 mins/cycle, 6 cycles in Output Voltage • See table each of 3 axes Minimum Load • No minimum load required Start Up Delay • 1.5 s max at 115 VAC EMC & Safety Hold Up Time • DLG50/75: No hold up Emissions • EN55015, class B conducted and radiated DLG100/150: 16 ms minimum Line Regulation • ±0.5% Harmonic Currents • EN61000-3-2, class A EN61000-3-2, class C for loads >80% Load Regulation • ±1.0% in constant voltage mode, Voltage Flicker • EN61000-3-3 ±5.0% in constant current mode Turn On Overshoot • 5% max ESD Immunity • EN61000-4-2, 8 kV air and 4 kV contact, Perf Criteria A Transient Response • 5% maximum deviation, recovery to within Radiated Immunity • EN61000-4-3, level 2 Perf Criteria A 1% in 10 ms for a 50% load change Ripple & Noise • DLG50/75(1) EFT/Burst • EN61000-4-4, level 2 Perf Criteria A DLG100/150: 150 mV pk-pk up to 36 V Surge • EN61000-4-5, installation class 3, output, 200 mV for 48 V output, 240 mV Perf Criteria A for ≥54 V output (see note 2) Conducted Immunity • EN61000-4-6, level 2 Perf Criteria A Overvoltage Protection • 110-142%, recycle mains to reset, only on Dips & Interruptions • EN61000-4-11, 30% 10 ms, DLG100 & DLG150 versions 60% 100 ms, 100% 5000 ms, Overtemperature • Unit shuts down, recycle mains to reset Perf Criteria A, B, B Protection Safety Approvals • EN61347, UL8750, CE Mark Overload Protection • 105% maximum, auto recovery Short Circuit Protection • Trip and restart (hiccup mode) Temp. Coefficient • 0.04%/°C Notes 1. DLG50/75 use a topology which results in increased levels of mains frequency related ripple. Contact technical sales for details.

A DLG50-150 Models and Ratings C Output Voltage - Output Power Output Voltage Output Current Range in Constant Efficiency(1) Model Number Current Mode D 50 W 12.0 V 4.20 A 8.5-12.0 V 84.0% DLG50PS12 C 50 W 24.0 V 2.10 A 19.0-24.0 V 86.0% DLG50PS24 50 W 36.0 V 1.40 A 26.0-36.0 V 88.0% DLG50PS36 50 W 48.0 V 1.05 A 35.0-48.0 V 88.0% DLG50PS48 59 W 12.0 V 4.90 A 8.5-12.0 V 84.0% DLG75PS12 75 W 24.0 V 3.15 A 19.0-24.0 V 86.0% DLG75PS24 74 W 30.0 V 2.45 A 22.0-30.0 V 87.0% DLG75PS30 75 W 36.0 V 2.10 A 26.0-36.0 V 88.0% DLG75PS36 67 W 48.0 V 1.40 A 35.0-48.0 V 88.0% DLG75PS48 75 W 54.0 V 1.40 A 37.0-54.0 V 88.0% DLG75PS54 100 W 12.0 V 8.30 A 9.0-12.0 V 88.0% DLG100PS12 100 W 15.0 V 6.60 A 10.0-15.0 V 88.0% DLG100PS15(3) 100 W 24.0 V 4.20 A 14.0-24.0 V 90.0% DLG100PS24 100 W 30.0 V 3.30 A 22.0-30.0 V 90.0% DLG100PS30 100 W 36.0 V 2.80 A 26.0-36.0 V 90.0% DLG100PS36 100 W 48.0 V 2.10 A 34.0-48.0 V 90.5% DLG100PS48 100 W 57.0 V 1.75 A 43.0-57.0 V 90.5% DLG100PS57(3) 132 W 12.0 V 11.00 A 9.0-12.0 V 88.0% DLG150PS12 150 W 15.0 V 10.00 A 11.0-15.0 V 88.0% DLG150PS15(3) 150 W 24.0 V 6.30 A 14.0-24.0 V 90.0% DLG150PS24 150 W 30.0 V 5.00 A 22.0-30.0 V 90.0% DLG150PS30 150 W 36.0 V 4.20 A 26.0-36.0 V 90.0% DLG150PS36 150 W 48.0 V 3.20 A 33.0-48.0 V 90.0% DLG150PS48 150 W 54.0 V 2.80 A 38.0-54.0 V 90.0% DLG150PS54(3) Notes 1. Typical efficiency at full load and 230 VAC input. 3. Not UL8750 approved. 2. Measured using 12” twisted pair with 0.1 µF and 47 µF capacitors in parallel at 20 MHz bandwidth. Mechanical Details A 0.28 (7.0) B 2.68 (68.0) 0.35 C (8.9) DLG50/75 DLG100/150 4-R2.1 AC IN DC OUT 1.35 (34.2) ACL A 6.93 (176.0) 8.74 (222.0) V+ (RED) ACN B 6.38 (162.0) 8.19 (208.0) V- (BLACK) 18AWGx3C 18 AWGx2C (DLG50/75/100- C 6.03 (153.2) 7.83 (199.0) see note 4 below) 14 AWGx2C (DLG150) 0.35 (8.9) Notes 11.81±0.79 (300±20) 11.8 1±0.79 (300±20) 1. All dimensions shown in inches (mm). 2. Weight: DLG50/75: 1.98 lbs (900 g) 1.54 (39.0) DLG100/150 2.29 lbs (1040 g) 3. Tolerance: ±0.02 (0.5) 4. DLG100PS12 and DLG100PS15 output cable is 14 AWG. Application Notes Constant Voltage / Constant Current Curve Vo max Output Voltage Vo min Trip & Restart Zone 0 10 20 30 40 50 60 70 80 90 100 Output Current (%) Derating Curve 100 100 A A B B 80 80 C %) 60 %) 60 Load ( 40 AB DDLLGG115500 aatt 121350 VVAACC & DLG100 C Load ( 40 A DLG50/75 20 C DLG50/75 20 B DLG100 C DLG150 0 0 0 10 20 30 40 50 55 60 70 90 100 115 130 180 220 240 305 -30 for DLG100/150 Ambient Temp (˚C) Input Voltage (VAC) 60Hz -40 for DLG50/75 Ta= 25˚C 27 Sept 16