D3C Ultra Subminiature Detection Switch Ultra Subminiature Detection Switch with Slide Mechanism and Lever Actuator ●Compact and light weight with 3-mm long stroke. (cid:14832) 3 ●Built-in slide mechanism allows selection of C shorting or non-shorting switching timing to match the application. RoHS Compliant Model Number Legend Contact Form D3C-@1 2@2 0 ●SPDT 1. Switching timing 1 : Non-shorting Model 2 : Shorting Model 2. Maximum Operating Force (OF) NO COM NC 1 : 1.28N {130 gf} 3 1 2 2 : 0.39N {40 gf} Contact Specifications List of models Specification Slide Contact Material Silver plated Operating Force (OF) 1.28 N {130 gf} (Standard) 0.39 N {40 gf} (Low force) Minimum applicable load Switching timing 5 VDC 1 mA Actuator Non-shorting Shorting Non-shorting Shorting (reference value) * * Please refer to "●Using Micro Loads" in "Precautions" Rotary lever D3C-1210 D3C-2210 D3C-1220 D3C-2220 for more information on the minimum applicable load. Ratings Characteristics Rated voltage Resistive load Permissible operating speed 1 mm to 500 mm/s 30 VDC 0.1 A Permissible operating Mechanical 200 operations/min Note.The above rating values were applied under the frequency Electrical 30 operations/min following test conditions. Insulation resistance 100 MΩ min. (at 250 VDC with insulation tester) (1) Ambient temperature: 20±2°C (2) Ambient humidity: 65±5% RH Contact resistance (initial value) 50 mΩ max. (3) Operating frequency: 30 operations/min Between terminals of the same 250 VAC 50/60 Hz for 1 min polarity Dielectric strength Between current-carrying 250 VAC 50/60 Hz for 1 min metal parts and ground Vibration resistance *1 Malfunction 10 to 55 Hz, 1.5 mm double amplitude Durability 1,000 m/s2 {approx. 100G} max. Shock resistance Malfunction *1 300 m/s2 {approx. 30G}max. Durability *2 50,000 operations min. (30 operations/min) Degree of protection IEC IP00 -20 to +80°C (at ambient humidity 60% max.) Ambient operating temperature (with no icing or condensation) Ambient operating humidity 85% max. (for +5 to +35°C) Weight Approx. 0.3g Note.The data given above are initial values. *1. The given values apply for Total Travel Position. Close or open circuit of the contact is 1 ms max. *2. For testing conditions, consult your OMRON sales representative. 1

D3C Ultra Subminiature Detection Switch Mounting Holes (Unit: mm) M1.6 Tap 4±0.1 5.7±0.1 1.6 dia. holes Dimensions and Operating Characteristics (Unit: mm) D3C-1210, D3C-2210 B A 5.6 D3C-1220, D3C-2220 1dia. holes 4.2 (cid:14832) 8.7 R1 1.6 Type Non-Shorting Shorting 3 6.7 C 1.6+00.12 dia. holes 5.7±0.15 FP OChpaerraactitnegr istics Model D3C -1210 D3C -1220 D3C -2210 D3C -2220 OP Operating Force OF Max. 1.28 N {130 gf} 0.39 N {40 gf} 1.28 N {130 gf} 0.39 N {40 gf} 6 4.7 4.6 max. 4±0.15 Releasing Force RF Min. (00..9180 N N { 1{1000 ggff}}) (00.2.093 NN { {330 ggff}}) (00.9.180 N N { 1{1000 ggff}}) (00..2093 NN { {330 ggf}f}) 1 (0.15 N {15 gf}) (0.05 N {5 gf}) (0.15 N) {15 gf} (0.05 N {5 gf}) 3.5 1.5- 00. 1 5 dia. FOrpeeer aPtoinsgit iPoons ition OFPP 1 Max. 3.54±.80 .m3 mm m 3.44±.80 .m3 mm m OP2 2.5±0.3 mm 2.6±0.3 mm 0.8 0.3 Total Travel Position TTP 1.3±0.4 mm 1.3±0.4 mm 0.9 2.542.54 4 <PCB Mounting 8 Dimensions (Reference)> 2.54 3-1dia. holes Switching timing 2.54 Non-shorting Model Shorting Model FP OP1 OP2 TTP FP OP1 OP2 TTP 4.2 2（NC） 2（NC） 1 1 3（NO） 3（NO） 8 Note 1.Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. Note 2.The values for operating characteristics apply for operation in the A direction (straight line), and the values in parentheses indicate those for operation in the B (rotary) direction for reference. Precautions ★Please refer to "Common Precautions" for correct use. Cautions ●Soldering ●Mounting Plate For soldering time, we recommend to solder within 3 s at a Use materials other than ABS or polycarbonate for the mounting soldering iron temperature of under 350°C. Soldering at a plate. Since grease is used for the Switch, it may cause cracks if temperature exceeding 350°C, soldering for more than 3 s, or grease from the Switch comes in contact with such materials. repeated soldering will degrade the Switch characteristics. ●Using Micro Loads Make sure that flux and liquid surface of the solder does not flow Use models that operate in the following range. However, even over the edge of the board when soldering. Please complete when using micro load models within the following operating soldering at a temperature of 260°C within 5 s. range, if inrush current occurs when the contact is opened or It is also recommended closed, it may increase the contact wear and so decrease that you apply flux durability. Therefore, insert a contact protection circuit where guard to the mounting Switch mounting surface necessary. The N-level reference value applies for the minimum surface of the Switch. applicable load. This value indicates the malfunction reference level for the reliability level of 60% (λ60). (JIS C5003) The equation, λ60=0.5×10-6/operation indicates that the Correct Use 1 estimated malfunction rate is less than operations with 2,000,000 ●Mounting a reliability level of 60%. Use M1.6 mounting screw with plane washers or spring washers V) e ( to securely mount the Switch. Tighten the screws to a torque of oltag 30 0.16 mA 100 mA 4.9 to 9.8×10-2 N·m {0.5 to 1 kgf·cm}. V ●Application of Operation Force to the Lever 24 Do not apply loads from any other directions other than operating direction of the lever as shown in the following figure. Operating range It may damage the Switch or cause malfunction. 12 5 1 mA 0 0.1 1 10 100 1,000 Current (mA) 2

D3C Ultra Subminiature Detection Switch (cid:14832) 3 C (cid:129) Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product. (cid:129) Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious influence on lives and property if used improperly. Make sure that the ratings and performance characteristics of the product provide a margin of safety for the system or equipment, and be sure to provide the system or equipment with double safety mechanisms. Note: Do not use this document to operate the Unit. OMRON Corporation ELECTRONIC AND MECHANICAL COMPONENTS COMPANY Contact: www.omron.com/ecb Cat. No. C099-E1-04 0812(0207)(O) 3

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: O mron: D3C-2210 D3C-2220 D3C-1210 D3C-1220