CRCW-HP e3 www.vishay.com Vishay Draloric Pulse Proof, High Power Thick Film Chip Resistors FEATURES • Excellent pulse load capability • Enhanced power rating • Double side printed resistor element • AEC-Q200 qualified • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 The pulse proof, high power thick film chip resistors series APPLICATIONS is the perfect choice for most fields of power measurement • Automotive electronics where reliability, stability, high power rating and • Industrial excellent pulse load performance are of major concern. Typical applications include battery management systems in automotive appliances. TECHNICAL SPECIFICATIONS CRCW0402- CRCW0603- CRCW0805- CRCW1206- CRCW1210- CRCW1218- CRCW2010- CRCW2512- DESCRIPTION HP e3 HP e3 HP e3 HP e3 HP e3 HP e3 HP e3 HP e3 Imperial size 0402 0603 0805 1206 1210 1218 2010 2512 Metric size code RR1005M RR1608M RR2012M RR3216M RR3225M RR3246M RR5025M RR6332M Resistance range 1  to 1 M jumper (0) Resistance tolerance ± 5 %; ± 1 %; ± 0.5 % Temperature coefficient ± 200 ppm/K; ± 100 ppm/K Rated dissipation, P (1) 0.2 W (2) 0.25 W 0.5 W 0.75 W (3) 0.75 W 1.5 W 1.0 W 1.5 W 70 Operating voltage, 50 V 75 V 150 V 200 V 200 V 200 V 400 V 500 V U AC /DC max. RMS Permissible film 155 °C temperature, F max. (1) Operating temperature -55 °C to +155 °C range Max. resistance change at P70 for resistance range, |R/R| after: 1000 h  2.0 % 8000 h  4.0 % Permissible voltage against ambient (insulation): 1 min, U 75 V 100 V 200 V 300 V 300 V 300 V 300 V 300 V ins Notes • Marking: See document “Surface Mount Resistor Marking” (www.vishay.com/doc?20020). (1) Please refer to APPLICATION INFORMATION below. (2) CRCW0402-HP resistors feature a single side printed resistive layer only. (3) Specified power rating requires a thermal resistance of R = 110 K/W. th APPLICATION INFORMATION When the resistor dissipates power, a temperature rise above the ambient temperature occurs, dependent on the thermal resistance of the assembled resistor together with the printed circuit board. The rated dissipation applies only if the permitted film temperature is not exceeded. These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime. Revision: 16-Sep-16 1 Document Number: 20043 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CRCW-HP e3 www.vishay.com Vishay Draloric TEMPERATURE COEFFICIENT AND RESISTANCE RANGE TYPE / SIZE TCR TOLERANCE RESISTANCE E-SERIES ± 200 ppm/K ± 5 % 1  to 1 M E24 ± 1 % CRCW0402-HP e3 ± 100 ppm/K 1  to 1 M E24; E96 ± 0.5 % Jumper, Imax. = 3 A  10 m 0  - ± 200 ppm/K ± 5 % 1  to 1 M E24 ± 1 % CRCW0603-HP e3 ± 100 ppm/K 1  to 1 M E24; E96 ± 0.5 % Jumper, Imax. = 5 A  8 m 0  - ± 200 ppm/K ± 5 % 1  to 1 M E24 ± 1 % CRCW0805-HP e3 ± 100 ppm/K 1  to 1 M E24; E96 ± 0.5 % Jumper, Imax. = 6 A  5 m 0  - ± 200 ppm/K ± 5 % 1  to 1 M E24 ± 1 % CRCW1206-HP e3 ± 100 ppm/K 1  to 1 M E24; E96 ± 0.5 % Jumper, Imax. = 10 A  5 m 0  - ± 200 ppm/K ± 5 % 1  to 1 M E24 ± 1 % CRCW1210-HP e3 ± 100 ppm/K 1  to 1 M E24; E96 ± 0.5 % Jumper, Imax. = 12 A  4 m 0  - ± 200 ppm/K ± 5 % 1  to 1 M E24 ± 1 % CRCW1218-HP e3 ± 100 ppm/K 1  to 1 M E24; E96 ± 0.5 % Jumper, Imax. = 20 A  4 m 0  - ± 200 ppm/K ± 5 % 1  to 1 M E24 ± 1 % CRCW2010-HP e3 ± 100 ppm/K 1  to 1 M E24; E96 ± 0.5 % Jumper, Imax. = 12 A  5 m 0  - ± 200 ppm/K ± 5 % 1  to 1 M E24 ± 1 % CRCW2512-HP e3 ± 100 ppm/K 1  to 1 M E24; E96 ± 0.5 % Jumper, Imax. = 16 A  5 m 0  - Note • The temperature coefficient of resistance (TCR) is not specified for 0  jumpers. PACKAGING PACKAGING TYPE / SIZE CODE QUANTITY PACKAGING STYLE WIDTH PITCH DIMENSIONS ED = ET7 10 000 Ø 180 mm / 7" CRCW0402-HP e3 2 mm EE = EF4 50 000 Ø 330 mm / 13" EI = ET2 5000 Ø 180 mm / 7" ED = ET3 10 000 Ø 180 mm / 7" 2 mm EL = ET4 20 000 Ø 285 mm / 11.25" CRCW0603-HP e3 EE = ET8 20 000 Ø 330 mm / 13" EA = ET1 5000 Ø 180 mm / 7" EB = ET5 10 000 4 mm Ø 285 mm / 11.25" EC = ET6 20 000 Paper tape acc. to Ø 330 mm / 13" 8 mm EA = ET1 5000 IEC 60286-3, Type 1a Ø 180 mm / 7" CRCW0805-HP e3 EB = ET5 10 000 4 mm Ø 285 mm / 11.25" EC = ET6 20 000 Ø 330 mm / 13" EA = ET1 5000 Ø 180 mm / 7" CRCW1206-HP e3 EB = ET5 10 000 4 mm Ø 285 mm / 11.25" EC = ET6 20 000 Ø 330 mm / 13" EA = ET1 5000 Ø 180 mm / 7" CRCW1210-HP e3 EB = ET5 10 000 4 mm Ø 285 mm / 11.25" EC = ET6 20 000 Ø 330 mm / 13" CRCW1218-HP e3 EK = ET9 4000 4 mm Ø 180 mm / 7" EF = E02 4000 4 mm Ø 180 mm / 7" CRCW2010-HP e3 Blister tape acc. to EJ = E08 16 000 12 mm 4 mm Ø 330 mm / 13" IEC 60286-3, Type 2a EG = E67 2000 8 mm CRCW2512-HP e3 Ø 180 mm / 7" EH = E82 4000 4 mm Revision: 16-Sep-16 2 Document Number: 20043 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CRCW-HP e3 www.vishay.com Vishay Draloric PART NUMBER AND PRODUCT DESCRIPTION Part Number: CRCW0603562RFKEAHP Part Number: CRCW06030000Z0EAHP C R C W 0 6 0 3 5 6 2 R F K E A H P TYPE / SIZE VALUE TOLERANCE TCR PACKAGING SPECIAL CRCW0402 R = decimal D = ± 0.5 % K = ± 100 ppm/K EA up to 2 digits CRCW0603 K = thousand F = ± 1 % N = ± 200 ppm/K EB HP = pulse proof, CRCW0805 M = million J = ± 5 % 0 = jumper EC high power CRCW1206 0000 = jumper Z = jumper ED CRCW1210 EE CRCW1218 EF CRCW2010 EG CRCW2512 EI EJ EH EK EL Product Description: CRCW0603-HP 100 562R 1 % ET1 e3 Product Description: CRCW0603-HP 0R0 ET1 e3 CRCW0603-HP 100 562R 1 % ET1 e3 TYPE / SIZE TCR RESISTANCE VALUE TOLERANCE PACKAGING LEAD (Pb)-FREE CRCW0402-HP ± 100 ppm/K 10R = 10  ± 0.5 % ET1, ET2, e3 = pure tin CRCW0603-HP ± 200 ppm/K 562R = 562  ± 1 % ET3, ET4, termination CRCW0805-HP 10K = 10 k ± 5 % ET5, ET6, finish CRCW1206-HP 1M = 1 M ET7, ET8, CRCW1210-HP 0R0 = jumper ET9, EF4, CRCW1218-HP E02, E08, CRCW2010-HP E67, E82 CRCW2512-HP Revision: 16-Sep-16 3 Document Number: 20043 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CRCW-HP e3 www.vishay.com Vishay Draloric DESCRIPTION The products do not contain any of the banned Production is strictly controlled and follows an extensive set substances as per IEC 62474, GADSL, or the SVHC list, of instructions established for reproducibility. A cermet film see www.vishay.com/how/leadfree. layer and a glass-over are deposited on both sides of a high Hence the products fully comply with the following grade (Al O ) ceramic substrate with its prepared inner directives: 2 3 contacts on both sides. A special laser is used to achieve • 2000/53/EC End-of-Life Vehicle Directive (ELV) and the target value by smoothly fine trimming the resistive layer Annex II (ELV II) without damaging the ceramics. The resistor elements are • 2011/65/EU Restriction of the Use of Hazardous covered by a protective coating designed for electrical, Substances Directive (RoHS) with amendment mechanical and climatic protection. The terminations 2015/863/EU receive a final pure tin on nickel plating. A three or • 2012/19/EU Waste Electrical and Electronic Equipment four-character code marking designates the resistance Directive (WEEE) values in accordance with IEC 60062. The three-character Vishay pursues the elimination of conflict minerals from its code system is applicable to values from E24 series only, supply chain, see the Conflict Minerals Policy at while the four-character code system is applicable to values www.vishay.com/doc?49037. from E96 and E24 series. The result of the determined production is verified by an APPROVALS extensive testing procedure on 100 % of the individual chip The resistors are qualified according to AEC-Q200. resistors. Only accepted products are laid directly into the Where applicable, the resistors are tested in accordance tape in accordance with IEC 60286-3 Type 1a and Type 2a (1). with EN 140401-802 which refers to EN 60115-1, EN 60115-8 and the variety of environmental test ASSEMBLY procedures of the IEC 60068 (1) series. The resistors are suitable for processing on automatic SMD assembly systems. They are suitable for automatic RELATED PRODUCTS soldering wave, reflow or vapor phase as shown in IEC 61760-1 (1). The encapsulation is resistant to all For more information about products with superior surge cleaning solvents commonly used in the electronics and pulse performance please refer to datasheet: industry, including alcohols, esters and aqueous solutions. D/CRCW-IF e3, Pulse Proof Thick Film Chip Resistors  The suitability of conformal coatings, potting compounds www.vishay.com/doc?20024. and their processes, if applied, shall be qualified by For thick film resistors with standard requirements for power appropriate means to ensure the long-term stability of the rating, please refer to datasheet: whole system. D/CRCW e3, Standard Thick Film Chip The resistors are RoHS-compliant, the pure tin plating www.vishay.com/doc?20035. provides compatibility with lead (Pb)-free and For anti-surge products and high power rating, please refer lead-containing soldering processes. Solderability is to datasheet: specified for 2 years after production or requalification. The RCS e3, Anti-Surge High Power Thick Film Chip Resistors  permitted storage time is 20 years. The immunity of the www.vishay.com/doc?20065. plating against tin whisker growth has been proven under extensive testing. MATERIALS Vishay acknowledges the following systems for the regulation of hazardous substances: • IEC 62474, Material Declaration for Products of and for the Electrotechnical Industry, with the list of declarable substances given therein (2) • The Global Automotive Declarable Substance List (GADSL) (3) • The REACH regulation (1907/2006/EC) and the related list of substances with very high concern (SVHC) (4) for its supply chain Notes (1) The quoted IEC standards are also released as EN standards with the same number and identical contents. (2) The IEC 62474 list of declarable substances is maintained in a dedicated database, which is available at http://std.iec.ch/iec62474. (3) The Global Automotive Declarable Substance List (GADSL) is maintained by the American Chemistry Council and available at www.gadsl.org. (4) The SVHC list is maintained by the European Chemical Agency (ECHA) and available at http://echa.europa.eu/candidate-list-table. Revision: 16-Sep-16 4 Document Number: 20043 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CRCW-HP e3 www.vishay.com Vishay Draloric FUNCTIONAL PERFORMANCE Single Pulse Axis Title neW) 10 000 2512 10000 2 nd lise Load ( 1000 1211202211108006 Pul 100 0805 1000 ^P-max. 10 00640032 1st line2nd line 1 100 0.1 0.01 10 0.000001 0.00001 0.0001 0.001 0.01 0.1 1 10 100 t-Pulse Duration (s) i 2nd line Maximum pulse load, single pulse; applicable if P 0 and n < 1000 and Û  Ûmax.; for permissible resistance change equivalent to 8000 h operation Continuous Pulse Axis Title neW) 10 000 2512 10000 2 nd liLoad ( 1000 121202111800 se 1206 Pul 100 0805 1000 ntinuous 10 00640032 1st line2nd line o C 1 100 - ^Pmax. 0.1 0.01 10 0.000001 0.00001 0.0001 0.001 0.01 0.1 1 10 100 t-Pulse Duration (s) i 2nd line Maximum pulse load, continuous pulses; applicable if PP (amb) and Û  Ûmax.; for permissible resistance change equivalent to 8000 h operation Revision: 16-Sep-16 5 Document Number: 20043 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CRCW-HP e3 www.vishay.com Vishay Draloric Pulse Voltage Axis Title 2000 10000 eV) d linge ( 1800 2512 2 nVolta 1600 2010 se 1400 1000 ul 1200 ^U-Pmax. 1080000 1206, 1210, 1218 1st line2nd line 100 600 0805 400 0603 200 0402 0 10 0.000001 0.00001 0.0001 0.001 0.01 0.1 1 10 t-Pulse Duration (s) i 2nd line Maximum pulse voltage, single and continuous pulses; applicable if PˆPˆmax.; for permissible resistance change equivalent to 8000 h operation Derating Axis Title 70 W) 1.8 CRCW1218-HP, CRCW2512-HP 10000 on ( 1.6 CRCCWR1C2W062-H01P0, -CHRPCW1210-HP 2nd line-Power Dissipati 011...1824 CCCRRRCCCWWW000864000532---HHHPPP 1000 1st line2nd line P 0.6 100 0.4 0.2 0 10 -50 0 50 100 150 ϑ -Ambient Temperature (°C) amb 2nd line Revision: 16-Sep-16 6 Document Number: 20043 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CRCW-HP e3 www.vishay.com Vishay Draloric TESTS AND REQUIREMENTS All executed tests are carried out in accordance with the The testing also covers most of the requirements specified following specifications: by EIA/IS-703 and JIS-C-5201-1. EN 60115-1, generic specification The tests are carried out under standard atmospheric EN 60115-8 (successor of EN 140400), sectional conditions in accordance with IEC 60068-1, 4.3, whereupon specification the following values are applied: EN 140401-802, detail specification Temperature: 15 °C to 35 °C IEC 60068-2-xx, test methods Relative humidity: 25 % to 75 % The parameters stated in the Test Procedures and Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar). Requirements table are based on the required tests A climatic category LCT / UCT / 56 is applied, defined by the and permitted limits of EN 140401-802. The table presents lower category temperature (LCT), the upper category only the most important tests, for the full test schedule refer temperature (UCT), and the duration of exposure in the to the documents listed above. However, some additional damp heat, steady state test (56 days). tests and a number of improvements against those The components are mounted for testing on boards in minimum requirements have been included. accordance with EN 60115-8, 2.4.2 unless otherwise specified. TEST PROCEDURES AND REQUIREMENTS IEC EN 60115-1 60068-2 (1) REQUIREMENTS TEST PROCEDURE CLAUSE TEST PERMISSIBLE CHANGE (R) METHOD Stability for product types: STABILITY CLASS 2 OR BETTER CRCW-HP e3 1 to 1 M 4.5 - Resistance - ± 0.5 %; ± 1 %; ± 5 % Temperature (20 / -55 / 20) °C and 4.8 - ± 100 ppm/K; ± 200 ppm/K coefficient (20 / 155 / 20) °C U = P x R or U = U 70 max.; whichever is the less severe; 1.5 h on; 0.5 h off 4.25.1 - Endurance at 70 °C 70 °C; 1000 h ± (2 % R + 0.1 ) 70 °C; 8000 h ± (4 % R + 0.1 ) Endurance at 4.25.3 - upper category 155 °C, 1000 h ± (2 % R + 0.1 ) temperature Damp heat, (40 ± 2) °C; 56 days; 4.24 78 (Cab) ± (1 % R + 0.05 ) steady state (93 ± 3) % RH; Damp heat, (85 ± 2) °C; (85 ± 5) % RH; 4.37 67 (Cy) steady state, U = 0.1 x P x R  100 V; ± (2 % R + 0.1 ) 85 accelerated 1000 h 4.23 - Climatic sequence: - 4.23.2 2 (Bb) dry heat 125 °C; 16 h 55 °C; 24 h;  90 % RH; 4.23.3 30 (Db) damp heat, cyclic 1 cycle 4.23.4 1 (Ab) cold -55 °C; 2 h ± (2 % R + 0.1 ) 4.23.5 13 (M) low air pressure 8.5 kPa; 2 h; (25 ± 10) °C 55 °C; 24 h; 4.23.6 30 (Db) damp heat, cyclic  90 % RH; 5 cycles 4.23.7 - DC load U = P70 x R  Umax.; 1 min - 1 (Aa) Cold -55 °C; 2 h ± (0.5 % R + 0.05 ) Revision: 16-Sep-16 7 Document Number: 20043 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CRCW-HP e3 www.vishay.com Vishay Draloric TEST PROCEDURES AND REQUIREMENTS IEC EN 60115-1 60068-2 (1) REQUIREMENTS TEST PROCEDURE CLAUSE TEST PERMISSIBLE CHANGE (R) METHOD Stability for product types: STABILITY CLASS 2 OR BETTER CRCW-HP e3 1 to 1 M 30 min at -55 °C and Rapid change of ± (1 % R + 0.05 ) 4.19 14 (Na) 30 min at 125 °C; temperature no visible damage 1000 cycles U = 2.5 x P70 x R  2 x Umax.; 4.13 - Short time overload whichever is the less severe; ± (2 % R + 0.05 ) 5 s Severity no. 4: U = 10 x P x R or Single pulse high 70 ± (1 % R + 0.05 ) 4.27 - U = 2 x U voltage overload max.; no visible damage whichever is the less severe; 10 pulses 10 μs/700 μs U = 15 x P x R or 70 U = 2 x U Periodic electric max.; ± (1 % R + 0.05 ) 4.39 - whichever is the less severe; overload no visible damage 0.1 s on; 2.5 s off; 1000 cycles Electrostatic IEC 61340-3-1 (1); 4.38 - discharge 3 pos. + 3 neg. discharges; ± (1 % R + 0.05 ) (human body model) ESD voltage acc. to the size Endurance by sweeping; 10 Hz to 2000 Hz; no resonance; ± (0.5 % R + 0.05 ) 4.22 6 (Fc) Vibration amplitude  1.5 mm or no visible damage  200 m/s2; 7.5 h Solder bath method; Sn60Pb40 non-activated flux; (235 ± 5) °C; (2 ± 0.2) s Good tinning ( 95 % covered) 4.17 58 (Td) Solderability Solder bath method; no visible damage Sn96.5Ag3Cu0.5 non-activated flux; (245 ± 5) °C; (3 ± 0.3) s Solder bath method Resistance to 4.18 58 (Td) (260 ± 5) °C; ± (0.5 % R + 0.05 ) soldering heat (10 ± 1) s Component solvent Isopropyl alcohol; 4.29 45 (XA) No visible damage resistance +50 °C; method 2 CRCW0402-HP and Shear CRCW0603-HP: 9 N 4.32 21 (Uu ) No visible damage 3 (adhesion) CRCW0805-HP to CRCW2512-HP: 45 N Depth 2 mm; ± (0.25 % R + 0.05 ) 4.33 21 (Uu ) Substrate bending 1 3 times no visible damage, no open circuit in bent position 4.7 - Voltage proof U = 1.4 x U ; 60 s No flashover or breakdown ins Flammability, IEC 60695-11-5 (1); 4.35 - No burning after 30 s needle flame test 10 s Note (1) The quoted IEC standards are also released as EN standards with the same number and identical contents. Revision: 16-Sep-16 8 Document Number: 20043 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CRCW-HP e3 www.vishay.com Vishay Draloric DIMENSIONS DIMENSIONS AND MASS L W H T1 T2 MASS TYPE / SIZE (mm) (mm) (mm) (mm) (mm) (mg) CRCW0402-HP e3 1.0 ± 0.05 0.5 ± 0.05 0.3 ± 0.10 0.25 ± 0.10 0.2 ± 0.10 0.65 CRCW0603-HP e3 1.6 ± 0.10 0.85 ± 0.10 0.45 ± 0.10 0.3 ± 0.20 0.3 ± 0.20 2 CRCW0805-HP e3 2.0 ± 0.15 1.25 ± 0.15 0.5 ± 0.10 0.4 ± 0.20 0.35 ± 0.20 5.5 CRCW1206-HP e3 3.1 ± 0.20 1.6 ± 0.15 0.5 ± 0.15 0.5 ± 0.20 0.45 ± 0.20 10 CRCW1210-HP e3 3.2 ± 0.20 2.5 ± 0.20 0.6 ± 0.10 0.45 ± 0.20 0.4 ± 0.20 18 CRCW1218-HP e3 3.1 ± 0.20 4.6 ± 0.20 0.6 ± 0.10 0.45 ± 0.20 0.4 ± 0.20 31 CRCW2010-HP e3 5.0 ± 0.15 2.5 ± 0.15 0.6 ± 0.10 0.6 ± 0.20 0.6 ± 0.20 25.5 CRCW2512-HP e3 6.3 ± 0.20 3.15 ± 0.15 0.6 ± 0.10 0.6 ± 0.20 0.6 ± 0.20 42 SOLDER PAD DIMENSIONS G X Y Z RECOMMENDED SOLDER PAD DIMENSIONS WAVE SOLDERING REFLOW SOLDERING TYPE / SIZE G Y X Z G Y X Z (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) CRCW0402-HP e3 - - - - 0.45 0.6 0.6 1.65 CRCW0603-HP e3 0.65 1.10 1.25 2.85 0.75 0.75 1.00 2.25 CRCW0805-HP e3 0.90 1.30 1.60 3.50 1.00 0.95 1.45 2.90 CRCW1206-HP e3 1.40 1.40 1.95 4.20 1.50 1.05 1.8 3.60 CRCW1210-HP e3 1.80 1.45 2.95 4.70 1.70 1.10 2.80 4.90 CRCW1218-HP e3 1.60 1.50 5.10 4.60 1.70 1.10 4.90 4.90 CRCW2010-HP e3 3.60 1.65 2.85 6.90 3.70 1.20 2.70 6.10 CRCW2512-HP e3 4.90 1.60 3.50 8.10 5.00 1.25 3.35 7.50 Notes • The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g in standards IEC 61188-5-x (1) or in publication IPC-7351. Still, the given solder pad dimensions will be found adequate for most general applications. (1) The quoted IEC standards are also released as EN standards with the same number and identical contents. Revision: 16-Sep-16 9 Document Number: 20043 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Legal Disclaimer Notice www.vishay.com Vishay Disclaimer  ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: V ishay: CRCW12062K00FKEAHP CRCW120610K0FKEAHP CRCW201010R0FKEFHP CRCW1206100KFKEAHP CRCW120615K0FKEAHP CRCW12061R00JNEAHP CRCW120610R0FKEAHP CRCW12061K00FKEAHP CRCW04020000Z0EDHP CRCW06030000Z0EAHP CRCW12060000Z0EAHP CRCW08050000Z0EAHP CRCW0603100KFKEAHP CRCW121012R0JNEAHP CRCW1210510RJNEAHP CRCW1210240RJNEAHP CRCW12103K30FKEAHP CRCW1210750RFKEAHP CRCW1210150RFKEAHP CRCW06032M49DHEAP CRCW04021K00FKEDHP CRCW040210K0FKEDHP CRCW060310K0FKEAHP CRCW06031K00FKEAHP CRCW08051K00FKEAHP CRCW080510K0FKEAHP CRCW251210R0FKEGHP CRCW2512100RFKEGHP CRCW201010K0FKEFHP CRCW2010100RFKEFHP CRCW20101K00FKEFHP CRCW25121K00FKEGHP CRCW080520K0FKEAHP CRCW20102K21FKEFHP CRCW08051R00FKEAHP CRCW080515R0FKEAHP CRCW12061R00FKEAHP CRCW0402100KFKEDHP CRCW0402100KJNEDHP CRCW0402100RFKEDHP CRCW0402100RJNEDHP CRCW040210K0JNEDHP CRCW040210R0FKEDHP CRCW040210R0JNEDHP CRCW040215K0FKEDHP CRCW04021K00JNEDHP CRCW04021K50FKEDHP CRCW04021M00FKEDHP CRCW04021M00JNEDHP CRCW04021R00FKEDHP CRCW04021R00JNEDHP CRCW040220K0FKEDHP CRCW0402220KJNEDHP CRCW0402220RJNEDHP CRCW040222K0JNEDHP CRCW040222R0FKEDHP CRCW040222R0JNEDHP CRCW040222R1FKEDHP CRCW04022K00FKEDHP CRCW04022K20JNEDHP CRCW04022R20JNEDHP CRCW040233R0FKEDHP CRCW040233R2FKEDHP CRCW0402470KJNEDHP CRCW0402470RJNEDHP CRCW040247K0FKEDHP CRCW040247K0JNEDHP CRCW040247R0JNEDHP CRCW0402499RFKEDHP CRCW040249K9FKEDHP CRCW040249R9FKEDHP CRCW04024K70FKEDHP CRCW04024K70JNEDHP CRCW04024K75FKEDHP CRCW04024K99FKEDHP CRCW04024R70JNEDHP CRCW040275R0FKEDHP CRCW0603100KJNEAHP CRCW0603100RFKEAHP CRCW0603100RJNEAHP CRCW060310K0JNEAHP CRCW060310R0FKEAHP CRCW060310R0JNEAHP CRCW060315K0FKEAHP CRCW06031K00JNEAHP CRCW06031K50FKEAHP CRCW06031M00FKEAHP CRCW06031M00JNEAHP CRCW06031R00FKEAHP CRCW06031R00JNEAHP CRCW060320K0FKEAHP CRCW0603220KJNEAHP CRCW0603220RJNEAHP CRCW060322K0JNEAHP CRCW060322R0JNEAHP CRCW06032K00FKEAHP CRCW06032K20JNEAHP CRCW06032R20JNEAHP CRCW060330K9FKEAHP CRCW060333R0FKEAHP