D/CRCW-HR e3 www.vishay.com Vishay Lead (Pb)-Free Thick Film, Rectangular High Value Chip Resistor FEATURES • High resistance values (up to 470M) • Suitable for voltage dividers and hybrids • Pure tin plating provides compatibility with lead (Pb)-free and lead containing soldering processing • Metal glaze on high quality ceramic • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 STANDARD ELECTRICAL SPECIFICATIONS LIMITING POWER ELEMENT CASE CASE TEMPERATURE RESISTANCE RATING VOLTAGE TOLERANCE MODEL SIZE SIZE COEFFICIENT RANGE SERIES P U % INCH METRIC 70 max. ppm/K  W AC /DC RMS V D11/CRCW0603-HR 0603 RR 1608M 0.10 75 ± 500 ± 5 11M to 470M E24 D12/CRCW0805-HR 0805 RR 2012M 0.125 150 ± 500 ± 5 11M to 470M E24 D25/CRCW1206-HR 1206 RR 3216M 0.25 200 ± 500 ± 5 11M to 470M E24 Notes • These resistors do not feature a limited lifetime when operated within the limits of rated dissipation, permissible operating voltage, and permissible film temperature. However, the resistance typically increase due to the resistor’s film temperature over operating time, generally known as drift. The drift may exceed the stability requirements of an individual application circuit and thereby limits the functional time. • Marking and packaging: See datasheet “Surface Mount Resistor Marking” (www.vishay.com/doc?20020) • Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material. TECHNICAL SPECIFICATIONS PARAMETER UNIT D11/CRCW0603-HR D12/CRCW0805-HR D25/CRCW1206-HR Rated Dissipation at P (1) W 0.1 0.125 0.25 70 Operating Voltage U AC /DC V 75 150 200 max. RMS < 100M: < 0.1 Voltage Coefficient %/V > 100M: < 0.3 Insulation Voltage U (1 min) V 100 200 300 ins Insulation Resistance  > 109 Operating Temperature Range °C - 55 to + 155 Weight mg 2 5.5 10 Note (1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded. Revision: 12-Jun-12 1 Document Number: 20022 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

D/CRCW-HR e3 www.vishay.com Vishay PART NUMBER AND PRODUCT DESCRIPTION Part Number: CRCW060316M0JPEAHR C R C W 0 6 0 3 1 6 M 0 J P E A H R MODEL/SIZE RESISTANCE TOLERANCE TCR PACKAGING SPECIAL CRCW0603 M = Million J = ± 5 % P = ± 500 ppm/K EA Up to 2 digits CRCW0805 EB HR = High value CRCW1206 EC Product Description: D11/CRCW0603-HR 500 16M 5 % ET1 e3 D11/CRCW0603-HR 500 16M 5 % ET1 e3 MODEL TCR RESISTANCE TOLERANCE PACKAGING LEAD (Pb)-FREE D11/CRCW0603-HR ± 500 ppm/K 68M = 68 M ± 5 % ET1 e3 = Pure tin D12/CRCW0805-HR 227M = 227 M ET5 termination finish D25/CRCW1206-HR ET6 PACKAGING MODEL CODE QUANTITY CARRIER TAPE WIDTH PITCH REEL DIAMETER EA = ET1 5000 180 mm/7" D11/CRCW0603-HR EB = ET5 10 000 8 mm 4 mm 285 mm/11.25" EC = ET6 20 000 330 mm/13" EA = ET1 5000 Paper tape acc. to 180 mm/7" D12/CRCW0805-HR EB = ET5 10 000 IEC 60068-3 8 mm 4 mm 285 mm/11.25" EC = ET6 20 000 Type I 330 mm/13" EA = ET1 5000 180 mm/7" D25/CRCW1206-HR EB = ET5 10 000 8 mm 4 mm 285 mm/11.25" EC = ET6 20 000 330 mm/13" DIMENSIONS SOLDER PAD DIMENSIONS in millimeters SIZE DIMENSIONS in millimeters REFLOW SOLDERING WAVE SOLDERING INCH METRIC L W H T1 T2 a b l a b l 0603 1608 1.55 + 0.10 0.85 ± 0.1 0.45 ± 0.05 0.3 ± 0.2 0.3 ± 0.2 0.5 0.9 1.0 0.9 0.9 1.0 - 0.05 0805 2012 2.0 + 0.20 1.25 ± 0.15 0.45 ± 0.05 0.3 + 0.10 0.3 ± 0.2 0.7 1.3 1.2 0.9 1.3 1.3 - 0.10 - 0.20 1206 3216 3.2 + 0.10 1.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 1.7 2.0 1.1 1.7 2.3 - 0.20 Revision: 12-Jun-12 2 Document Number: 20022 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

D/CRCW-HR e3 www.vishay.com Vishay DERATING P70 n atio 100 p ssi % Di d e at R of n 50 o cti a Fr 0 - 50 0 50 70 100 °C 150 Ambient Temperature in amb TEST PROCEDURES AND REQUIREMENTS IEC REQUIREMENTS EN 60115-1 60068-2 PERMISSIBLE CHANGE (R) TEST PROCEDURE CLAUSE TEST METHOD STABILITY CLASS 2 OR BETTER Stability for product types: D/CRCW-HR e3 11 M to 470 M 4.5 _ Resistance - ± 5 % 4.13 _ Short time overload U = 2.5 x √P70 x R  2 x Umax.; ± (0.5 % R + 0.05 ) Duration acc. to style Solder bath method; Good tinning ( 95 % covered); no visible Sn60Pb40 damage Solder bath method; 4.17.2 58 (Td) Solderability Sn96, 5Ag3Cu0.5 or Sn99, 3Cu0.7 Good tinning ( 95 % covered); no visible non-activated flux; damage (245 ± 5) °C or (250 ± 5) °C (3 ± 0.3) s Temperature 20 °C/- 55 °C/20 °C and 4.8.4.2 _ ± 500 ppm/K coefficient 20 °C/125 °/20 °C RR 1608: 9 N 4.32 21 (Uu ) Shear (adhesion) No visible damage 3 RR 2012 and RR 3216: 45N No visible damage, no open circuit in bent Depth 2 mm; 4.33 21 (Uu ) Substrate bending position 1 3 times ± (0.25 % R + 0.05 ) 30 min. at - 55 °C; Rapid change of 30 min. at 125 °C 4.19 14 (Na) temperature 5 cycles ± (0.5 % R + 0.05 ) 1000 cycles ± (1 % R + 0.05 ) Climatic sequence: 4.23 _ - Dry Heat 4.23.2 2 (Ba) 125 °C; 16 h Damp heat, cyclic 4.23.3 30 (Db) 55 °C;  90 % RH; 24 h; 1 cycle Cold 4.23.4 1 (Aa) - 55 °C; 2 h ± (2 % R + 0.1 ) Low air pressure 4.23.5 13 (M) 1 kPa; (25 ± 10) °C; 1 h 4.23.6 30 (Db) 55 °C;  90 % RH Damp heat, cyclic 24 h; 5 cycle 4.23.7 _ D.C. Load U = √P70 x R Revision: 12-Jun-12 3 Document Number: 20022 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

D/CRCW-HR e3 www.vishay.com Vishay TEST PROCEDURES AND REQUIREMENTS IEC REQUIREMENTS EN 60115-1 60068-2 PERMISSIBLE CHANGE (R) TEST PROCEDURE CLAUSE TEST METHOD STABILITY CLASS 2 OR BETTER Stability for product types: D/CRCW-HR e3 11 M to 470 M U = √P70 x R  Umax. Endurance at 1.5 h on; 0,5 h off; 4.25.1 _ 70 °C 70 °C; 1000 h ± (2 % R + 0.1 ) 70 °C; 8000 h ± (4 % R + 0.1 ) Solder bath method Resistance to 4.18.2 58 (Td) (260 ± 5) °C; ± (0.5 % R + 0.05 ) soldering heat (10 ± 1) s Damp heat, (40 ± 2) °C; 4.24 78 (Cab) ± (2 % R + 0.1 ) steady state (93 ± 3) % RH; 56 days Endurance at upper 4.25.3 _ 155 °C; 1000 h ± (2 % R + 0.1 ) category temperature All tests are carried out in accordance with the following specifications: • EN 60115-1, generic specification • EN 140400, sectional specification • EN 140401-802, detail specification • IEC 60068-2-x, variety of environmental test procedures Packaging of components is done in paper or blister tapes according to IEC 60286-3. Revision: 12-Jun-12 4 Document Number: 20022 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROV E RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose o r the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustainin g applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk . Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this documen t or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2019 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2019 1 Document Number: 91000