CRA12E, CRA12S www.vishay.com Vishay Thick Film Chip Resistor Array FETAURES • Convex terminal array available with either scalloped corners (E version) or square corners (S version) • Wide ohmic range: 10R to 1M0 • 8 or 10 terminal package with isolated resistors • Pure tin solder contacts on Ni barrier layer, provides compatibility with lead (Pb)-free and lead containing soldering processes • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 STANDARD ELECTRICAL SPECIFICATIONS POWER RATING LIMITING ELEMENT TEMPERATURE RESISTANCE TOLERANCE MODEL CIRCUIT P VOLTAGE MAX. COEFFICIENT RANGE SERIES 70 °C ± % W V ± ppm/K  01; 02; 20 0.100 100 1 10 to 1M E24; E96 CRA12E 50 0.125 200 2; 5 10 to 1M E24 CRA12S 03 Zero-Ohm-Resistor: Rmax. = 50 m, Imax. = 1.5 A TECHNICAL SEPCIFICATIONS CRA12E AND CRA12S CRA12E AND CRA12S PARAMETER UNIT CIRCUIT 01; 02; 20 CIRCUIT 03 Rated dissipation at P (1) W per element 0.1 0.125 70 Limiting element voltage  V 50 U AC/DC max. Insulation voltage U (1 min) V 100 ins Insulation resistance  > 109 Category temperature range °C - 55 to + 155 Note (1) Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material. PART NUMBER AND PRODUCT DESCRIPTION Part Number: CRA12E08347K0JTR (2) C R A 1 2 E 0 8 3 4 7 K 0 J T R TERMINAL MODEL PIN CIRCUIT VALUE TOLERANCE PACKAGING SPECIAL STYLE CRA12 S 08 1 = 01 R = Decimal F = ± 1 % TR Up to 2 digits E 10 2 = 02 K = Thousand G = ± 2 % TL 3 = 03 M = Million J = ± 5 % 8 = 20 0000 = 0  Z = 0  Jumper Jumper Product Description: CRA12E 08 03 47K 5 % RB8 e3 CRA12E 08 03 47K 5% RB8 e3 RESISTANCE MODEL PIN CIRCUIT TOLERANCE PACKAGING LEAD (Pb)-FREE VALUE CRA12E 08 01 10R = 10  ± 1 % RB8 e3 = Pure tin CRA12S 10 02 47K = 47 k ± 2 % RD7 termination finish 03 1M = 1M ± 5 % 20 0R0 = Jumper Note (2) Preferred way for ordering products is by use of the PART NUMBER. Revision: 24-Jun-13 1 Document Number: 31003 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CRA12E, CRA12S www.vishay.com Vishay AVAILABLE TYPES AND RANGES TERMINAL TEMPERATURE MODEL CIRCUIT TOLERANCE COUNT COEFFICIENT 01 02 CRA12S 10 03 20 ± 100 ppm/K ± 1 %; ± 2 %; ± 5 % 01 ± 200 ppm/K 08 02 CRA12E 03 10 20 PACKAGING BLISTER TAPE MODEL TAPE WIDTH DIAMETER PITCH PIECES/REEL ACC. IEC 60286-3, TYPE II PART NUMBER PRODUCT DESCRIPTION CRA12E 08 180 mm/7" 2000 TR RB8 CRA12E 10 12 mm 8 mm 330 mm/13" 5000 TL RD7 CRA12S 10 CIRCUIT 01 Circuit 02 Circuit 10 pin Pin 1 8 pin 10 pin Pin 1 03 Circuit 20 Circuit 8 pin 10 pin Pin 1 Revision: 24-Jun-13 2 Document Number: 31003 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CRA12E, CRA12S www.vishay.com Vishay DERATING % 120 n n i o 100 ati p si Dis 80 d e Rat 60 of n ctio 40 a Fr 20 0 - 55 - 25 0 25 50 75 100 125 155 175 70 Ambient Temperature in °C DIMENSIONS S-Version B E-Version B 3 3 P T P T 0 0 A* 1 A* 1 L B* B* L A A W W PIN 1 PIN 1 W W p p e d a a c a c a b e b PIN DIMENSIONS in millimeters SOLDER PAD DIMENSIONS in millimeters MODEL NO c w d p a b e # L A A* B B* P T W WAVE 2.2 4.3 0.57 1.27 0.71 1.05 1.09 CRA12E 8 5.08 0.79 - 0.51 0.38 1.27 0.55 3.05 REFLOW 2.2 3.9 0.57 1.27 0.71 0.86 1.09 CRA12E 10 6.40 0.79 - 0.51 0.38 1.27 0.55 3.05 CRA12S 10 6.40 0.79 0.89 0.51 0.38 1.27 0.55 3.05 TOL.± 0.15± 0.15± 0.15± 0.25± 0.2 ± 0.1± 0.15± 0.15 Revision: 24-Jun-13 3 Document Number: 31003 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CRA12E, CRA12S www.vishay.com Vishay TEST PROCEDURES AND REQUIREMENTS IEC REQUIREMENTS PERMISSIBLE EN 60068-2 CHANGE (R)(1) 60115-1 TEST PROCEDURE TEST STABILITY CLASS 1 STABILITY CLASS 2 CLAUSE METHOD OR BETTER OR BETTER Stability for product type: 10  to 1 M CRA12E/CRA12S 4.5 - Resistance - ± 1 % ± 2 %, ± 5 % 4.7 - Voltage proof U = 1.4 x U ; 60 s No flashover or breakdown ins 4.13 - Short time overload U = 2.5 x P70 x R  2 x Umax.; ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) Duration according to style Solder bath method; Sn60Pb40; Good tinning ( 95 % covered) non-activated flux; no visible damage (235 ± 5) °C; (2 ± 0.2) s 4.17.2 58 (Td) Solderability Solder bath method; Sn96.5Ag3Cu0.5; Good tinning ( 95 % covered) non-activated flux; no visible damage (245 ± 5) °C; (3 ± 0.3) s 4.8.4.2 - Temperature coefficient (20/- 55/20) °C and (20/125/20) °C ± 100 ppm/K ± 200 ppm/K 4.32 21 (U ) Shear (adhesion) 45 N No visible damage U3 No visible damage, 4.33 21 (U ) Substrate bending Depth 2 mm; 3 times no open circuit in bent position U1 ± (0.25 % R + 0.05 ) 30 min. at - 55 °C; 30 min at 125 °C 4.19 14 (Na) Rapid change of temperature 5 cycles ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) 1000 cycles ± (1 % R + 0.05 ) ± (1 % R + 0.05 ) 4.23 - Dry heat - 4.23.2 2 (Ba) Damp heat, cyclic 125 °C; 16 h 4.23.3 30 (Db) Cold 55 °C;  90 % RH; 24 h; 1 cycle 4.23.4 1 (Aa) Low air pressure - 55 °C; 2 h ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) 4.23.5 13 (M) - 1 kPa; (25 ± 10) °C; 1 h 4.23.6 30 (Db) Damp heat, cyclic 55 °C;  90 % RH; 24 h; 5 cycle 4.23.7 - DC load U = P x R 70 U = P x RU 70 max. 1.5 h on; 0.5 h off; 4.25.1 - Endurance at 70 °C 70 °C; 1000 h ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) ± (2 % R + 0.1 ) ± (4 % R + 0.1 ) 70 °C; 8000 h Solder bath method; 4.18.2 58 (Td) Resistance to soldering heat ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) (260 ± 5) °C; (10 ± 1) s 4.35 - Flammability, needle flame test IEC 60695-11-5; 10 s No burning after 30 s 4.24 78 (Cab) Damp heat, steady state (40 ± 2) °C; (93 ± 3) % RH; 56 days ± (1 % R + 0.05 ) Endurance at 4.25.3 - 155 °C; 1000 h ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) upper category temperature IEC 61340-3-1; Electrostatic discharge 4.40 - 3 positive and 3 negative discharges; ± (1 % R + 0.05 ) (human body model) ESD voltage: 500 V 4.29 45 (XA) Component solvent resistance Isopropyl alcohol; 50 °C; method 2 No visible damage Isopropyl alcohol; 50 °C; method 1; Marking legible, 4.30 45 (XA) Solvent resistance of marking toothbrush no visible damage Vibration, endurance f = 10 Hz to 2000 Hz; x, y, z  1.5 mm; 4.22 6 (Fc) ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) by sweeping A  200 m/s2; 10 sweeps per axis 4.37 - Periodic electric overload U = 15 x P70 x R2 x Umax. ± (1 % R + 0.05 ) 0.1 s on; 2.5 s off; 1000 cycles 4.27 - Single pulse high voltage Û = 10 x P70 x R2 x Umax. ± (1 % R + 0.05 ) overload, 10 μs/700 μs 10 pulses Note (1) Figures are given for a single element. All tests are carried out in accordance with the following specifications: • EN 60115-1, generic specification • EN 140400, sectional specification • EN 140401-802, detail specification • IEC 60068-2 environmental test procedures Packaging of components is done in paper or blister tapes according to IEC 60286-3 Revision: 24-Jun-13 4 Document Number: 31003 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Legal Disclaimer Notice www.vishay.com Vishay Disclaimer  ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: V ishay: CRA12E0813K30GTR CRA12E08320K0JTR CRA12E10222K0JTR CRA12E101180RJTA CRA12E0831K00FTR CRA12E083100KJTR CRA12E08347R0JTR CRA12E08356R0JTR CRA12E08351R0JTR CRA12E08318R0JTR CRA12E08310R0JTR CRA12E08339R0JTR CRA12E08327R0JTR CRA12E16333R0JTR CRA12E08322R0JTR CRA12E083100KGTR CRA12E163100RJTA CRA12E08347K0JTR CRA12E083220RJTR CRA12E163510RGTR CRA12E083100RJTR CRA12E083150RJTR CRA12E16347K0JTA CRA12E163100KGTA CRA12E163120RJTA CRA12E083100RGTR CRA12E163182RFTR CRA12E1634K70JTA CRA12E1014K70GTR CRA12E1024K70JTR CRA12E1611K00FTA CRA12E1002-270J-RB8 (2000 T&R) CRA12E08310K0JTR CRA12E1614K70GTA CRA12E16149K9FTR CRA12E083120RJTR CRA12E1018K20GTR CRA12E16310K0JTR CRA12E0837K50GTR CRA12E08324K9FTR CRA12E10210K0JTR CRA12E08324R0GTR CRA12E16351R0GTR CRA12E08310R0GTR CRA12E08110K0GTR CRA12E10330K0GTR CRA12E1023K30JTR CRA12E16110K0JTA CRA12E16310K0JTA CRA12E161390RJTR CRA12E08312R0JTR CRA12E083150KJTR CRA12E08315K0JTR CRA12E0831K20JTR CRA12E0831K50GTR CRA12E08322K0JTR CRA12E083270KJTR CRA12E083330RGTR CRA12E0833K30FTR CRA12E08347R0GTR CRA12E08349R9FTR CRA12E083590RFTR CRA12E08375R0JTR CRA12E10110K0GTR CRA12E10110K0JTR CRA12E1011K00JTR CRA12E1012K00JTR CRA12E1012K70GTR CRA12E102100KJTR CRA12E10210K0GTR CRA12E102180RJTR CRA12E10220K0JTR CRA12E1022K00JTR CRA12E1022K20JTR CRA12E102330RGTR CRA12E102470KJTR CRA12E1024K70GTR CRA12E103100RFTR CRA12E10310K0GTR CRA12E10310R0JTR CRA12E1031K00GTR CRA12E1601822JRB8 CRA12E0401103GRB8 CRA12E0403103GRB8 CRA12E0803752GRB8 CRA12E080110K0JRB8 CRA12E0833K30JTR CRA12E0832K20JTR CRA12E04320K0FTR CRA12E10110K0FTA CRA12E1632K20GTR CRA12E1612K70GTR CRA12E0832K00JTR CRA12E0831K00JTR CRA12E0831M00JTR CRA12E0811K50GTR CRA12E0834K70JTR CRA12S1024K70JTR CRA12E1631K00GTA CRA12E0811K00GTR