End of Life - Last Available Purchase Date: 31-Dec-2019 CRA06E, CRA06S www.vishay.com Vishay Thick Film Chip Resistor Array FEATURES • Convex terminal array available with eithe r scalloped corners (E version) or square corner s (S version) • Wide ohmic range: 10  to 1 M • 4 or 8 terminal package with isolated resistors CRA06E and CRA06S Thick Film resistor arrays ar e • AEC-Q200 qualified constructed on a high grade ceramic body with convex • Material categorization: for definitions of complianc e terminations. A small package enables the design of high please see www.vishay.com/doc?99912 density circuits. The single component reduces boar d space, component counts and assembly costs. STANDARD ELECTRICAL SPECIFICATIONS POWER RATING LIMITING ELEMENT TEMPERATURE RESISTANCE TOLERANCE MODEL CIRCUIT P VOLTAGE MAX. COEFFICIENT RANGE SERIES 70 ± % W V ± ppm/K  100 1 E24; E96 CRA06E 03 0.063 50 10R to 1M 200 2; 5 E24 CRA06S Zero-Ohm-Resistor: Rmax. = 50 m, Imax. = 1 A TECHNICAL SPECIFICATIONS PARAMETER UNIT CRA06E AND CRA06S Rated dissipation at 70 °C (1) W per element 0.063 Limiting element voltage (2) V 50 Insulation voltage (1 min) V 100 DC/AC PEAK Category temperature range °C -55 to +155 Insulation resistance  > 109 Notes (1) Rated voltage: P x R (2) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rates dissipation applies only if the permitted film temperature of 155 °C is not exceed PART NUMBER AND PRODUCT DESCRIPTION Part Number: CRA06S08347K0JTA (1) C R A 0 6 S 0 8 3 4 7 K 0 J T A MODEL TERMINAL STYLE PIN CIRCUIT VALUE TOLERANCE PACKAGING (2) SPECIAL CRA06 S 04 3 = 03 R = decimal F = ± 1 % TA Up to 2 digits E 08 K = thousand G = ± 2 % TC M = million J = ± 5 % 0000 = 0  jumper Z = 0  jumper Product Description: CRA06S 08 03 -05 473 J RT1 e3 CRA06S 08 03 473 J RT1 e3 MODEL TERMINAL COUNT CIRCUIT TYPE RESISTANCE VALUE TOLERANCE PACKAGING LEAD (Pb)-FREE CRA06E 04 03 1R0 = 1  F = ± 1 % RT1 e3 = pure tin CRA06S 08 10R = 10  G = ± 2 % RT6 termination finish 47K = 47 k J = ± 5 % 1M0 = 1 M Z = 0  jumper 0R0 = jumper First two digits (3 for 1 %) are significant. Last digit is the multiplier Notes (1) Preferred way for ordering products is by use of the PART NUMBER (2) Please refer to table PACKAGING, see next page Revison: 25-Feb-2019 1 Document Number: 31002 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

End of Life - Last Available Purchase Date: 31-Dec-2019 CRA06E, CRA06S www.vishay.com Vishay AVAILABLE TYPES AND RANGES TEMPERATURE MODEL TERMINAL COUNT CIRCUIT TOLERANCE COEFFICIENT ± 100 ppm/K ± 1 % 04 03 ± 200 ppm/K ± 2 %; ± 5 % CRA06S ± 100 ppm/K ± 1 % 08 03 ± 200 ppm/K ± 2 %; ± 5 % ± 100 ppm/K ± 1 % CRA06E 08 03 ± 200 ppm/K ± 2 %; ± 5 % PACKAGING PACKAGING CODE PAPER TAPE MODEL TAPE WIDTH PITCH PIECES / REEL PRODUCT PART NUMBER DESCRIPTION 180 mm/7" 4 mm 5000 TA RT1 CRA06 330 mm/13" 4 mm 20 000 TC RT6 CIRCUIT 120 % 03 CIRCUIT n er i 100 w o P ed 80 at R 60 40 20 4 pin 8 pin 0 -55 -25 0 25 50 70 100 125 155 Derating Ambient Temperature in °C DIMENSIONS S-Version E-Version 1 103 103 PIN 1 e a a e PIN DIMENSIONS in millimeters REFLOW SOLDER PAD DIMENSIONS in millimeters MODEL NO# L A A B B* P T W MODEL PINS c w d p a b e 1 CRA06S 4 1.6 0.38 0.61 0.3 0.3 0.8 0.5 1.5 CRA06S 4 0.8 3.1 0.36 0.44 1.15 CRA06E 8 3.2 0.38 - 0.3 0.3 0.8 0.5 1.5 CRA06E 8 0.8 3.1 0.36 0.8 0.44 1.15 0.63 CRA06S CRA06S 8 3.2 0.38 0.61 0.3 0.3 0.8 0.5 1.5 TOL. ± 0.15 ± 0.15 ± 0.15 ± 0.15 ± 0.15 ± 0.1 ± 0.1 ± 0.15 Revison: 25-Feb-2019 2 Document Number: 31002 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

End of Life - Last Available Purchase Date: 31-Dec-2019 CRA06E, CRA06S www.vishay.com Vishay TEST PROCEDURES AND REQUIREMENTS EN 60115-1 REQUIREMENTS TEST PERMISSIBLE CHANGE (R/R) (1) CONDITIONS OF TEST (clause) STABILITY STABILITY CLASS 1 OR BETTER CLASS 2 OR BETTER Stability for product types: 10  to 1 M 10  to 1 M CRA06E / CRA06 S Resistance (4.5) - ± 1 % ± 2 %; ± 5 % (20 / -55 / 20) °C and Temperature coefficient (4.8.4.2) ± 100 ppm/K ± 200 ppm/K (20 / 125 / 20) °C U = 2.5 x (P x R)1/2 Overload (4.13) 70 ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )  2 x Umax.; 0.5 s Aging 4 h at 155 °C, dry heat Good tinning ( 95 % covered) Solderability (4.17.5) (2) solder bath method; 235 °C; 2 s no visible damage visual examination Solder bath method; Resistance to soldering heat (4.18.2) ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) (260 ± 5) °C; (10 ± 1) s 30 min at LCT = -55 °C; Rapid change of temperature (4.19) ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) 30 min at UCT = 125 °C; 5 cycles (40 ± 2) °C; 56 days; Damp heat, steady state (4.24) ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) (93 ± 3) % RH 16 h at UCT = 125 °C; 1 cycle at 55 °C; 2 h at LCT = -55 °C; 1 h/1 kPa at 15 °C to 35 °C; Climatic sequence (4.23) ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) 5 cycles at 55 °C U = (P x R)1/2 70 U = U ; whichever is less severe max. U = (P x R)1/2 70 U = U ; whichever is less severe Endurance at 70 °C (4.25.1) max. ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) 1.5 h ON; 0.5 h OFF; 70 °C; 1000 h Extended endurance (4.25.1.8) Duration extended to 8000 h ± (2 % R + 0.1 ) ± (4 % R + 0.1 ) Endurance at upper category UCT = 125 °C; 1000 h ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) temperature (4.25.3) Notes (1) Figures are given for a single element (2) Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years APPLICABLE SPECIFICATIONS • EN 60115-1 Generic specification • EN 140400 Sectional specification • EN 140401-802 Detail specification • IEC 60068-2-X Variety of environmental test procedures • EIA 481 Packaging of SMD components Revison: 25-Feb-2019 3 Document Number: 31002 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROV E RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose o r the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustainin g applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk . Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this documen t or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2019 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2019 1 Document Number: 91000

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: V ishay: CRA06E083220RFTA CRA06S08386R6FTA CRA06S08343R2FTA CRA06E0838K20GTA CRA06E083270RJTA CRA06E083121RFTA CRA06E083110RFTA CRA06S083121RFTA CRA06S083750RFTA CRA06S083825RFTA CRA06S10210K0JTAR4 CRA06S1002332JRT1 CRA06S083249RFTA CRA06E083562RFTA CRA06E08327R0FTA CRA06E083665RFTA CRA06E08360R0FTA CRA06E08362R0FTA CRA06E0833K90JTA CRA06E0833K65FTA CRA06S08351R0GTB CRA06S08339R0GTA CRA06E08327R4FTA CRA06S083100KGTA CRA06E08031000FTR1 CRA06S1002154JRT1 CRA06S1002222JRT1 CRA06S1002393JRT1 CRA06S083182KFTA CRA06E083154RFTA CRA06E0832K20FTA CRA06S08313R0FTA CRA06S08333R0GTA CRA06S08356R2FTA CRA06S08362R0GTA CRA06S0838K25FTA CRA06E083118RFTA CRA06S043330RFTA CRA06S0834K99FTA