CRA04S www.vishay.com Vishay Thick Film Chip Resistor Array FEATURES • Convex terminal array with square corners • Wide ohmic range: 10R to 1M0 • 4 or 8 terminal package with isolated resistors • AEC-Q200 qualified • Material categorization: for definitions of compliance The CRA04S thick film resistor array is constructed on a high grade ceramic body with convex terminations. A small please see www.vishay.com/doc?99912 package enables the design of high density circuits. The single component reduces board space, component counts, and assembly costs. STANDARD ELECTRICAL SPECIFICATIONS POWER RATING LIMITING ELEMENT TEMPERATURE RESISTANCE TOLERANCE MODEL CIRCUIT P VOLTAGE MAX. COEFFICIENT RANGE E-SERIES 70 °C ± % W V ± ppm/K  100 1 24 + 96 0.063 50 10 to 1M CRA04S 03 200 2; 5 24 Zero-Ohm-Resistor: Rmax.  50 m, Imax. = 1 A TECHNICAL SPECIFICATIONS PARAMETER UNIT CRA04S Rated dissipation at 70 °C (2) W per element 0.063 Limiting element voltage (1) V 50 Insulation voltage (1 min) V 100 DC/AC peak Category temperature range °C -55 to +155 Insulation resistance  > 109 Notes (1) Rated voltage: P x R (2) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rate dissipation applies only if the permitted film temperature of 155 °C is not exceeded PART NUMBER AND PRODUCT DESCRIPTION Part Number: CRA04S08347K0JTD (1) C R A 0 4 S 0 8 3 4 7 K 0 J T D MODEL TERMINAL STYLE PIN CIRCUIT VALUE TOLERANCE PACKAGING (2) SPECIAL CRA04 S 04 3 = 03 R = decimal F = ± 1 % TD Up to 2 digits 08 K = thousand G = ± 2 % TC M = million J = ± 5 % PZ 0000 = 0  jumper Z = 0  jumper Product Description: CRA04S 08 03 473 J RT7 e3 CRA04S 08 03 473 J RT7 e3 MODEL TERMINAL COUNT CIRCUIT TYPE RESISTANCE VALUE TOLERANCE PACKAGING (4) LEAD (Pb)-FREE CRA04S 04 03 473 = 47 k F = ± 1 % RT7 e3 = pure tin 08 4702 = 47 k G = ± 2 % RT6 termination finish 10R0 = 10  J = ± 5 % PZ 100 = 10  Z = 0  jumper 000 = 0  jumper First two digits (3 for 1 %) are significant. Last digit is the multiplier. Notes (1) Preferred way for ordering products is by use of the PART NUMBER (2) Please refer to the table PACKAGING, see next page Revison: 23-Feb-17 1 Document Number: 31043 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CRA04S www.vishay.com Vishay PACKAGING PACKAGING CODE MODEL TAPE WIDTH DIAMETER PITCH PIECES/REEL PAPER TAPE PART NUMBER PRODUCT DESCRIPTION 180 mm/7" 2 mm 10 000 TD RT7 CRA04S 8 mm 330 mm/13" 2 mm 20 000 TC RT6 330 mm/13" 2 mm 50 000 PZ PZ CIRCUIT DERATING % 120 03 CIRCUIT n wer i 100 o P d ate 80 R 60 40 20 4 pin 8 pin 0 - 55 - 25 0 25 50 75 100 125 155 175 70 Ambient Temperature in °C DIMENSIONS PIN DIMENSIONS in millimeters NO # L A A B B* P T W 1 NOM. 1.0 4 - 0.33 0.15 0.25 0.65 0.35 1.0 ± 0.1 2.0 8 0.30 0.4 0.15 0.25 0.50 0.45 1.0 ± 0.2 TOL. - ± 0.15 ± 0.15 ± 0.10 ± 0.1 - ± 0.1 ± 0.15 SOLDER PAD DIMENSIONS in millimeters c w d a b e WAVE 0.45 1.45 0.2 0.4 0.5 0.3 The dimensions shown are for a 8 pin part. For parts with a e e different pin numbers use the same pitch and add or subtract pads as required. Revison: 23-Feb-17 2 Document Number: 31043 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CRA04S www.vishay.com Vishay TEST PROCEDURES AND REQUIREMENTS EN 60115-1 REQUIREMENTS TEST PERMISSIBLE CHANGE (R/R) (1) CONDITIONS OF TEST (clause) STABILITY STABILITY CLASS 1 OR BETTER CLASS 2 OR BETTER Stability for product types: 10  to 1 M 10  to 1 M CRA04S Resistance (4.5) - ± 1 % ± 2 %; ± 5 % (20 / -55 / 20) °C and Temperature coefficient (4.8.4.2) ± 100 ppm/K ± 200 ppm/K (20 / 125 / 20) °C U = 2.5 x (P x R)1/2 Overload (4.13) 70 ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )  2 x Umax.; 0.5 s Aging 4 h at 155 °C, dry heat Good tinning ( 95 % covered) Solderability (4.17.5) (2) solder bath method; 235 °C; 2 s no visible damage visual examination Solder bath method; Resistance to soldering heat (4.18.2) ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) (260 ± 5) °C; (10 ± 1) s 30 min at LCT = -55 °C; Rapid change of temperature (4.19) ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) 30 min at UCT = 125 °C; 5 cycles (40 ± 2) °C; 56 days; Damp heat, steady state (4.24) ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) (93 ± 3) % RH 16 h at UCT = 125 °C; 1 cycle at 55 °C; 2 h at LCT = -55 °C; 1 h/1 kPa at 15 °C to 35 °C; Climatic sequence (4.23) ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) 5 cycles at 55 °C U = (P x R)1/2 70 U = U ; whichever is less severe max. U = (P x R)1/2 70 U = U ; whichever is less severe Endurance at 70 °C (4.25.1) max. ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) 1.5 h “ON”; 0.5 h “OFF”; 70 °C; 1000 h Extended endurance (4.25.1.8) Duration extended to 8000 h ± (2 % R + 0.1 ) ± (4 % R + 0.1 ) Endurance at upper category UCT = 125 °C; 1000 h ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) temperature (4.25.3) Notes (1) Figures are given for a single element (2) Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years APPLICABLE SPECIFICATIONS • EN 60115-1 Generic specification • EN 140400 Sectional specification • EN 140401-802 Detail specification • IEC 60068-2-X Variety of environmental test procedures • EIA 481 Packaging of SMD components Revison: 23-Feb-17 3 Document Number: 31043 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Legal Disclaimer Notice www.vishay.com Vishay Disclaimer  ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: V ishay: CRA04S04322R0JTD CRA04S083100RJTD CRA04S08310K0GTD CRA04S08310K0JTD CRA04S08310R0JTD CRA04S0831K00JTD CRA04S08322R0JTD CRA04S0832K20JTD CRA04S0832K70JTD CRA04S08333R0JTD CRA04S08347K0JTD CRA04S08347R0JTD CRA04S0834K70GTD CRA04S0834K70JTD CRA04S08351K0GTD CRA04S08351R0JTD CRA04S08356R0JTD CRA04S0838K20JTD CRA04S08351R0GTD CRA04S08349R9FTD CRA04S0803000JRT7 CRA04S0803472JRT7 CRA04S0803620GRT7 CRA04S08327R0JTD CRA04S083390RJTD CRA04S08339R0JTD CRA04S08343R0JTD CRA04S08351K0JTD CRA04S08375R0JTD CRA04S08382R0JTD CRA04S0836K80GTD CRA04S08310R0GTD CRA04S0831K00GTD CRA04S08347K0GTD CRA04S08382K0GTD CRA04S08322R0FTD CRA04S083220RFTD CRA04S083220RJTD CRA04S0830000ZTD CRA04S083100KFTD