DataSheet PCB Mount CMX Series • SIP SSR • Ratings to 20A @ 60 VDC, 10A @ 100 VDC, 10A @ 60 VDC and 3A @ 200 VDC • MOSFET output • DC control • Low on-state impedance • CE Compliant to EN60950-1 PRODUCT SELECTION Control Voltage 3 A 5 A 6 A 10 A 10 A 20 A 3-10 VDC CMX200D3 CMX60D5 CMX100D6 CMX60D10 CMX100D10 CMX60D20 20-28 VDC CMXE200D3 CMXE60D5 CMXE100D6 CMXE60D10 CMXE100D10 CMXE60D20 OUTPUT SPECIFICATIONS (1)(5) Description Operating Voltage [VDC] 0-200 0-60 0-100 0-60 0-100 0-60 Maximum Off-State Leakage Current @ Rated Voltage [μAdc] 100 100 100 100(6) 100 100 Maximum Load Current [Arms] 3 5 6 10 10 20 Minimum Load Current [mArms] 2 2 2 2 2 2 Maximum On-State Resistence [Ohm] (2) 0.20 .10 .040 .018 .010 .0033 Maximum Surge Current (10msec) [Apk] 30 60 100 100 100 200 Maximum On-State Voltage Drop @ Rated Current [VDC] 0.6 0.5 0.24 0.18 0.1 0.1 INPUT SPECIFICATIONS (1) Description CMX CMXE Control Voltage Range 3.0-10.0 VDC 20-28 VDC Maximum Turn On Voltage 3.0 VDC 20 VDC Minimum Turn-Off Voltage 1 .0 VDC 1 .0 VDC Typical Input Current 15 mAdc @ 5 VDC 12 mAdc @ 24 VDC Nominal Input Impedance 300 Ohm 780 Ohm Maximum Turn-On Time [msec] 1.0 1.0 Maximum Turn-Off Time [μsec] 300 300 GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input/Output (50/60Hz) (3) 2500 Vrms Minimum Insulation Resistance (@ 500 VDC) (3) 109 Ohms Maximum Capacitance, Input/Output 15 pF Ambient Operating Temperature Range (4) -30ºC to 80ºC Ambient Storage Temperature Range (4) -30ºC to 125ºC Weight (typical) 0.4 oz. (11g) Encapsulation Thermally Conductive Epoxy Enclosure and PCB Meet the requirements of IEC60335-1 GENERAL NOTES 1) All parameters at 25°C unless otherwise specified. 2) @ rated current (RDS-ON) 3) Dielectric and insulation resistance are measured between input and output 4) Low temperature range is limited to -10°C in 20Amps models 5) Inductive loads should be diode suppressed 6) At 55 Vdc Do not forget to visit us at: www.crydom.com Copyright © 2018 Crydom Inc. Specifications subject to change without notice.

DataSheet PCB Mount WIRING DIAGRAM + 1 LOAD +VDC A Load can be wired in location A or B B 2 LOAD -VDC CONTROL CIRCUIT + 3 +VDC 4 -VDC THERMAL DERATE INFORMATION CMX100D6 12 CMX60D5 CMX200D3 S) P 10 7 M A 6 T ( 8 N CMX60D10 E R 6 S) 5 UR CMX100D10 P C M 4 D 4 A A NT ( 3 LO 2 E R CUR 2 0 20 40 60 80 D A 1 O AMBIENT TEMPERATURE (ºC) L 0 20 40 60 80 AMBIENT TEMPERATURE (ºC) S) CMX60D20 P 20 M A T ( 16 N E R 12 R U C D 8 A O L 4 0 20 40 60 80 AMBIENT TEMPERATURE (ºC) Do not forget to visit us at: www.crydom.com Copyright © 2018 Crydom Inc. Specifications subject to change without notice.

DataSheet PCB Mount MECHANICAL SPECIFICATIONS Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] .300 (7.6) .300 MAX (7.6) 1.00 1.00 MAX MAX (25.4) (25.4) .300 TYP. .300 TYP. (7.6) (.250.10) 4 (3.1770.08) 2 1 (T.01Y5.3P0). .100 (2.5) (7.6) (.250.10) 4 (3.1770.08) 2 1 (T.01Y5.3P0). (.120.50) 1.100 .040 (1.0) DIA. 1.100 .080 (2.0) DIA. (27.9) (4 PLACES) (27.9) (4 PLACES) 1.70 1.70 (43.1) MAX (43.1) PIN 1: +DC LOAD PIN 1: +DC LOAD PIN 2: -DC LOAD PIN 2: -DC LOAD PIN 3: +DC CONTROL PIN 3: +DC CONTROL PIN 4: -DC CONTROL PIN 4: -DC CONTROL AGENCY APPROVALS Agency Approvals Designed in accordance with the requirements of IEC 62314 EN60950 : Meets the requirements of sections1.5: 1,7: 2.9: 2.10.5.3: 4.2: 4.5: 4.7: IEC60335-1: Resistance to heat and fire meets the requirements of section 30, evaluated by TUV SUD. Glow Wire Test, per requirements of IEC/EN 60695-2-10 and IEC/EN 60695-2-11 Ball Pressure Test, per requirements of IEC/EN 60695-10-2 E116950 (3 Amps, 6 Amps and 10 Amps Models) Rev. 092618 ECN#20512 Do not forget to visit us at: www.crydom.com Copyright © 2018 Crydom Inc. Specifications subject to change without notice.

DataSheet PCB Mount DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF RIESGO DE RISQUE DE GEFAHR EINES RISCHIO DI 存在电击、 ELECTRIC DESCARGA DESCHARGE ELEKTRISCHE SCOSSA 爆炸或电弧 SHOCK, ELECTRICA O ELECTRIQUE N SCHLAGES ELETTRICA O 闪烁危险 EXPLOSION, EXPLOSION. OU EXPLOSION ODER EINER DELL’ESPLOSIONE. OR ARC FLASH. • Desconectar • Eteindre EXPLOSION. • Spenga tutta • 在操作此设 • Disconnect all todos los toutes les • Stellen Sie l'alimentazione 备之前请先 power before suministros de sources jeglichen che fornisce 关闭电源。 installing or energia a este d'énergie de Strom ab, der questa working with equipo antes cet appareil dieses Gerät apparecchiatura 若不遵守这些说明， this equipment. de trabajar avant de versorgt, bevor prima di lavorare con este equipo. travailler Sie an dem a questa 可能会导致严重的 • Verify all dessus de cet Gerät Arbeiten apparecchiatura 人身伤害甚至死亡。 connections • Verificar todas appareil durchführen and replace all las conexiones • Verificare tutti • Vor dem covers before y colocar todas • Vérifier tous i collegamenti Drehen auf turning on las tapas antes connections, et e sostituire Energie alle power. de energizer remettre tous tutte le coperture Anschlüsse el equipo. couverts en prima Failure to follow olace avant de überprüfen dell’accensione these El mettre sous und alle instructions will incumplimiento Abdeckungen L'omissione di result in death de estas De non-suivi de ersetzen. queste istruzioni or serious injury. instrucciones ces instructions Unterlassung provocherà la puede provocar provoquera la dieser morte o la muerte o mort ou des Anweisungen lesioni serie lesiones serias. lésions sérieuses können zum sérieuses. Tode oder zu schweren Verletzungen führen. WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 RISK OF MATERIAL DAMAGE AND HOT RISQUE DE DOMMAGE MATERIEL ET DE GEFAHR VON MATERIALSCHÄDEN UND ENCLOSURE SURCHAUFFE DU BOITIER GEHÄUSEERHITZUNG • The product's side panels may be hot, allow • Les panneaux latéraux du produit peuvent être • Die Seitenwände können heiß sein. Lassen Sie the product to cool before touching. chauds. Laisser le produit refroidir avant de le das Produkt abkühlen, bevor Sie es berühren. • Follow proper mounting instructions including toucher. • Beachten Sie die Montageanweisungen, torque values. • Respecter les consignes de montage, et • Führen Sie keine Flüssigkeiten oder • Do not allow liquids or foreign objects to enter notamment les couples de serrage. Fremdkörper in das Produkt ein. this product. • Ne pas laisser pénétrer de liquide ni de corps étrangers à l'intérieur du produit. Le non-respect de cette directive peut entraîner, Die Nichtbeachtung dieser Anweisung kann Failure to follow these instructions can result in des lésions corporelles graves ou des Körperverletzung oder Materialschäden serious injury, or equipment damage. dommages matériels. zur Folge haben. RIESGO DE DAÑOS MATERIALES Y DE 材料损坏和高温外壳的危险性 RISCHIO DI DANNI MATERIALI E D'INVOLUCRO SOBRECALENTAMIENTO DE LA UNIDAD CALDO • 产品的一侧面板可能很热，在其冷却前请 • Los paneles laterales del producto pueden • I pannelli laterali dell'apparecchio possono 不要触碰。 estar calientes. Esperar que el producto se scottare; lasciar quindi raffreddare il prodotto • 遵照正确的安装说明，包括扭矩值。 enfríe antes de tocarlo. • Respetar las instrucciones de montaje, y en prima di toccarlo. • 请勿让液体及其他异物进入本产品。 • Seguire le istruzioni di montaggio corrette. particular los pares de apretado. • Non far entrare liquidi o oggetti estranei in questo • No dejar que penetren líquidos o cuerpos apparecchio. extraños en el producto. La mancata osservanza di questa precauzione può 如不能正确执行这些操作说明， Si no se respetan estas precauciones pueden causare gravi rischi per l'incolumità personale o 极有可能造成严重人体伤害或者设备的损坏。 producirse graves lesiones, daños materiales. danni alle apparecchiature. Rev 073015 Do not forget to visit us at: www.crydom.com Copyright © 2018 Crydom Inc. Specifications subject to change without notice.

DataSheet PCB Mount ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Toxic or hazardous Substance and Elements Name Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium biphenyls diphenyl ethers (Cr (VI)) (PBB) (PBDE) Semiconductor die Solder 附件 - 环保信息 此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 部件 有毒有害物质或元素 名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) 半导体芯片 焊接点 50 Do not forget to visit us at: www.crydom.com Copyright © 2018 Crydom Inc. Specifications subject to change without notice.

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: S ensata: CMX100D6 CMX60D10 CMX60D5 CMX200D3 CMX60D20 CMX100D10 CMXE100D10 CMXE100D6 CMXE200D3 CMXE60D10 CMXE60D5 CMXE60D20