I N D U C T O R S June 2018 Inductors for Power Circuits Wound Ferrite CLF-D Series (For automobiles) CLF7045-D Type CLF7045-D ＊

(2/9) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (8) Public information-processing equipment (2) Transportation equipment (electric trains, ships, etc.) (9) Military equipment (3) Medical equipment (10) Electric heating apparatus, burning equipment (4) Power-generation control equipment (11) Disaster prevention/crime prevention equipment (5) Atomic energy-related equipment (12) Safety equipment (6) Seabed equipment (13) Other applications that are not considered general-purpose (7) Transportation control equipment applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. ＊ 20180627 / inductor_automotive_power_clf7045-d_en.fm

(3/9) I N D U C T O R S Inductors for Power Circuits Product compatible with RoHS directive Compatible with lead-free solder Wound Ferrite AEC-Q200 Overview of CLF7045-D Type FEATURES Magnetic shield type wound inductor for power circuits. It can be used at a wide temperature range. –40〜+150°C（Including self-temperature rise) 1 to 470µH, wide E-6 Series lineup allows for various usages. APPLICATION Equipment used for automobiles (ECM, airbags, headlights, electronic power steering, meters, ABS, other) PART NUMBER CONSTRUCTION CLF 7045 T - 1R0 N - D L×W×H Dimensions Inductance Inductance Series name Packaging style Internal code (mm) (µH) tolerance 7045 7.2×6.9×4.5 T Taping 1R0 1.0 M ±20% 100 10 N ±30% 101 100 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Package quantity Individual weight Type Operating Storage temperature temperature （°C） （°C） (pieces/reel) （g） CLF7045-D –40 to +150 –40 to +150 1000 0.72 Operating temperature range includes self-temperature rise. The Storage temperature range is for after the circuit board is mounted. RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/ Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. ＊ 20180627 / inductor_automotive_power_clf7045-d_en.fm

(4/9) I N D U C T O R S CLF7045-D Type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T4 e ur T3 T3 at er p m e T T2 T: t3 T1 t1 t2 t: Time Preheating Soldering Peak Temp. Time Temp. Time Temp. Time T1 T2 t1 T3 t2 T4 t3 150°C 180°C 60 to 120s 230°C 30s 250°C 5s Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. ＊ 20180627 / inductor_automotive_power_clf7045-d_en.fm

(5/9) I N D U C T O R S CLF7045-D Type SHAPE & DIMENSIONS 7.2±0.2 2 100 1 0. 0. ± ± 6.9 12410 2.0 (4.0) 1.6±0.15 1.6±0.15 3 0. ± 4.5 )0.1 ( Dimensions in mm RECOMMENDED LAND PATTERN 2 2. 2.0 3.9 2.0 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. ＊ 20180627 / inductor_automotive_power_clf7045-d_en.fm

(6/9) I N D U C T O R S CLF7045-D Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L Measuring frequency DC resistance Rated current Part No. Idc1 Idc2 (µH) Tolerance (kHz) () (A) (A) 1 ±30% 100 9.6m±30% 8.9 5.2 CLF7045T-1R0N-D 1.5 ±30% 100 11.0m±30% 7.3 4.9 CLF7045T-1R5N-D 2.2 ±30% 100 14.6m±30% 5.5 4.3 CLF7045T-2R2N-D 3.3 ±30% 100 16.4m±30% 5.0 4.1 CLF7045T-3R3N-D 4.7 ±30% 100 20m±30% 4.1 3.6 CLF7045T-4R7N-D 6.8 ±30% 100 27m±30% 3.3 3.0 CLF7045T-6R8N-D 10 ±20% 100 38m±20% 2.7 2.5 CLF7045T-100M-D 15 ±20% 100 51m±20% 2.3 2.1 CLF7045T-150M-D 22 ±20% 100 69m±20% 1.9 1.8 CLF7045T-220M-D 33 ±20% 100 0.11±20% 1.55 1.40 CLF7045T-330M-D 47 ±20% 100 0.15±20% 1.30 1.20 CLF7045T-470M-D 68 ±20% 100 0.21±20% 1.10 0.95 CLF7045T-680M-D 100 ±20% 100 0.33±20% 0.90 0.75 CLF7045T-101M-D 150 ±20% 100 0.48±20% 0.67 0.61 CLF7045T-151M-D 220 ±20% 100 0.66±20% 0.62 0.52 CLF7045T-221M-D 330 ±20% 100 1.03±20% 0.49 0.42 CLF7045T-331M-D 470 ±20% 100 1.42±20% 0.43 0.37 CLF7045T-471M-D Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (10% below the initial value) Idc2: When based on the temperature increase (Temperature increase of 30°C by self heating) ○Measurement equipment Measurement item Product No. Manufacturer L 4285A Agilent Technologies DC resistance VP-2941A Panasonic Rated current Idc1 4285A+42841A+42842C Agilent Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. ＊ 20180627 / inductor_automotive_power_clf7045-d_en.fm

(7/9) I N D U C T O R S CLF7045-D Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 10000 1000 471M 331M 221M 151M 101M 100 680M )H 470M µ (ce 330M n a ct 220M u d n 150M I 100M 10 6R8N 4R7N 3R3N 2R2N 1R5N 1 1R0N 0.1 10 100 1000 10000 Frequency(kHz) ○Measurement equipment Product No. Manufacturer 4294A Agilent Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. ＊ 20180627 / inductor_automotive_power_clf7045-d_en.fm

(8/9) I N D U C T O R S CLF7045-D Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 1000 471M 331M 221M 151M 100 101M 680M 470M 330M )H 220M µ (e 150M nc 10 a 100M ct u d n 6R8N I 4R7N 3R3N 2R2N 1R5N 1 1R0N 0.1 0 2 4 68 10 12 DC current(A) ○Measurement equipment Product No. Manufacturer 4285A+42841A+42842C Agilent Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. ＊ 20180627 / inductor_automotive_power_clf7045-d_en.fm

(9/9) I N D U C T O R S CLF7045-D Type PACKAGING STYLE REEL DIMENSIONS 2.0±0.5 E Type A W1 W2 N E CLF7045-D ø330 16.4 22.4 ø50 2 * These values are typical values. N (1.0) ø13.0±0.5 W1 ø21.0±0.8 W2 A Dimensions in mm TAPE DIMENSIONS øD0 P2 P0 P1 K E F W B A t Dimensions in mm Type A B øD0 E F P0 P1 P2 W K t CLF7045-D 7.5 7.5 1.5+0.1/-0 1.75±0.1 7.5±0.1 4.0±0.1 12.0±0.1 2.0±0.1 16.0±0.3 4.9 0.4 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. ＊ 20180627 / inductor_automotive_power_clf7045-d_en.fm