1 CC-E Insulation type DC-DC converter 5 Y E A R S warranty Low Voltage DirectiveCSAU CL2620.29 N5o0.6-10/950-1 EN60950-1 ■ Features ■ Model-naming method CC 3 - 05 05 S F -E ●Mounting area halved compared to existing products ●Nonuse of tantalum capacitor or aluminum electro- ShapeF: Horizontally-mounted DIP type R: Horizontally-mounted SMD type lytic capacitor FS Vertically-mounted SIP type Symbol for number of outputs ●Remote On/Off function incorporated in all series of S: Single output, D: Dual outputs products Nominal output voltage 03: 3.3V, 05: 5V, 12: 12V High accuracy of ± 3% in output voltage (10W of Nominal input voltage lower single output) 05: 5V, 12: 12V, 24: 24V, 48: 48V ●5-side metal-shielded low noise design Maximum output power ●Lightweight design with no resin filled up 1R5: 1.5W, 3: 3W, 6:6W 10: 10W, 15: 15W, 25: 25W ●Supports DIP insertion,SMD mountingand SIP verti- Representing series name by cal insertion (3W products) combination with "-E"at the end ●Approved by UL60950-1, CSA C22.2 No.60950-1 (C-UL), and EN60950-1 (NEMKO) ■ Conformity to RoHS Directive ■ Applications This means that, in conformity with EU Directive 2002/95/EC, lead, cadmium, mercury, hexavalent chromium, and specific bromine-based flame retar- dants, PBB and PBDE, have not been used, except for exempted applications. ■ Product Line up Model name Model name Model name Model name Output Input (output voltage: 3.3V) (output voltage: 5V) (output voltage: 12V/15V) (output voltage: ±12V/±15V) power voltage Output current DIP type SMD type SIP type Output current DIP type SMD type SIP type Output current DIP type SMD type SIP type Output current DIP type SMD type SIP type 5V 0.4A CC1R5-0503SF-ECC1R5-0503SR-E - 0.3A CC1R5-0505SF-E CC1R5-0505SR-E - 0.125A (0.1A)CC1R5-0512SF-E CC1R5-0512SR-E - 0.06A (0.05A)CC1R5-0512DF-ECC1R5-0512DR-E - 12V 0.4A CC1R5-1203SF-ECC1R5-1203SR-E - 0.3A CC1R5-1205SF-E CC1R5-1205SR-E - 0.125A (0.1A)CC1R5-1212SF-E CC1R5-1212SR-E - 0.06A (0.05A)CC1R5-1212DF-ECC1R5-1212DR-E - 1.5W 24V 0.4A CC1R5-2403SF-ECC1R5-2403SR-E - 0.3A CC1R5-2405SF-E CC1R5-2405SR-E - 0.125A (0.1A)CC1R5-2412SF-E CC1R5-2412SR-E - 0.06A (0.05A)CC1R5-2412DF-ECC1R5-2412DR-E - 48V 0.4A CC1R5-4803SF-ECC1R5-4803SR-E - 0.3A CC1R5-4805SF-E CC1R5-4805SR-E - 0.125A (0.1A)CC1R5-4812SF-E CC1R5-4812SR-E - 0.06A (0.05A)CC1R5-4812DF-ECC1R5-4812DR-E - 5V 0.8A CC3-0503SF-E CC3-0503SR-E CC3-0503SS-E 0.6A CC3-0505SF-E CC3-0505SR-E CC3-0505SS-E 0.25A (0.2A) CC3-0512SF-E CC3-0512SR-E CC3-0512SS-E0.125A (0.1A) CC3-0512DF-E CC3-0512DR-E CC3-0512DS-E 12V 0.8A CC3-1203SF-E CC3-1203SR-E CC3-1203SS-E 0.6A CC3-1205SF-E CC3-1205SR-E CC3-1205SS-E 0.25A (0.2A) CC3-1212SF-E CC3-1212SR-E CC3-1212SS-E0.125A (0.1A) CC3-1212DF-E CC3-1212DR-E CC3-1212DS-E 3W 24V 0.8A CC3-2403SF-E CC3-2403SR-E - 0.6A CC3-2405SF-E CC3-2405SR-E CC3-2405SS-E 0.25A (0.2A) CC3-2412SF-E CC3-2412SR-E CC3-2412SS-E0.125A (0.1A) CC3-2412DF-E CC3-2412DR-E CC3-2412DS-E 48V 0.8A CC3-4803SF-E CC3-4803SR-E CC3-4803SS-E 0.6A CC3-4805SF-E CC3-4805SR-E CC3-4805SS-E 0.25A (0.2A) CC3-4812SF-E CC3-4812SR-E - 0.125A (0.1A) CC3-4812DF-E CC3-4812DR-E CC3-4812DS-E 5V 1.2A CC6-0503SF-E CC6-0503SR-E - 1A CC6-0505SF-E CC6-0505SR-E - 0.5A (0.4A) CC6-0512SF-E CC6-0512SR-E - 0.25A (0.2A) CC6-0512DF-E CC6-0512DR-E - 12V 1.2A CC6-1203SF-E CC6-1203SR-E - 1.2A CC6-1205SF-E CC6-1205SR-E - 0.5A (0.4A) CC6-1212SF-E CC6-1212SR-E - 0.25A (0.2A) CC6-1212DF-E CC6-1212DR-E - 6W 24V 1.2A CC6-2403SF-E CC6-2403SR-E - 1.2A CC6-2405SF-E CC6-2405SR-E - 0.5A (0.4A) CC6-2412SF-E CC6-2412SR-E - 0.25A (0.2A) CC6-2412DF-E CC6-2412DR-E - 48V 1.2A CC6-4803SF-E CC6-4803SR-E - 1.2A CC6-4805SF-E CC6-4805SR-E - 0.5A (0.4A) CC6-4812SF-E CC6-4812SR-E - 0.25A (0.2A) CC6-4812DF-E CC6-4812DR-E - 5V 2.5A CC10-0503SF-E CC10-0503SR-E - 2A CC10-0505SF-E CC10-0505SR-E - 0.8A (0.64A) CC10-0512SF-E CC10-0512SR-E - 0.4A (0.32A) CC10-0512DF-E CC10-0512DR-E - 12V 2.5A CC10-1203SF-E CC10-1203SR-E - 2A CC10-1205SF-E CC10-1205SR-E - 1A (0.8A) CC10-1212SF-E CC10-1212SR-E - 0.45A (0.36A) CC10-1212DF-E CC10-1212DR-E - 10W 24V 2.5A CC10-2403SF-E CC10-2403SR-E - 2A CC10-2405SF-E CC10-2405SR-E - 1A (0.8A) CC10-2412SF-E CC10-2412SR-E - 0.45A (0.36A) CC10-2412DF-E CC10-2412DR-E - 48V 2.5A CC10-4803SF-E CC10-4803SR-E - 2A CC10-4805SF-E CC10-4805SR-E - 1A (0.8A) CC10-4812SF-E CC10-4812SR-E - 0.45A (0.36A) CC10-4812DF-E CC10-4812DR-E - 15W 24V 4.5A CC15-2403SF-E CC15-2403SR-E - 3A CC15-2405SF-E CC15-2405SR-E - - - - - - - - - 25W 24V 7.5A CC25-2403SF-E CC25-2403SR-E - 5A CC25-2405SF-E CC25-2405SR-E - - - - - - - - - ・All specifications are subject to change without notice. web180416

CC1R5-E 2 CC1R5-E Specifications ITEMS/UNITS MODEL CC1R5-0503Sx-E CC1R5-0505Sx-E CC1R5-0512Sx-E CC1R5-0512Dx-E Nominal Voltage V DC5.0 Voltage Range V DC4.5-9.0 Input Efficiency (typ) (*1) ％ 71 77 80 79 Current (typ) (*1) A 0.372 0.390 0.375 0.380 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 0.400 0.300 0.125 0.100 0.060 0.050 Maximum Power (*2) W 1.32 1.5 Maximum Line Regulation (Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature–40°C to +50°C) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 3.2 Mechanical Size (W x H x D) mm DIP: 16.51 x 8.5 x 16.6 / SMD: 16.51 x 8.8 x 16.6 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ITEMS/UNITS MODEL CC1R5-1203Sx-E CC1R5-1205Sx-E CC1R5-1212Sx-E CC1R5-1212Dx-E Nominal Voltage V DC12 Voltage Range V DC9.0-18 Input Efficiency (typ) (*1) ％ 73 78 82 81 Current (typ) (*1) A 0.151 0.160 0.152 0.154 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 0.400 0.300 0.125 0.100 0.060 0.050 Maximum Power (*2) W 1.32 1.5 Maximum Line Regulation (Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature–40°C to +50°C) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 ±5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4-15.0 11.4 - 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 3.2 Mechanical Size (W x H x D) mm DIP: 16.51 x 8.5 x 16.6 / SMD: 16.51 x 8.8 x 16.6 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ・All specifications are subject to change without notice.

CC1R5-E 3 ITEMS/UNITS MODEL CC1R5-2403Sx-E CC1R5-2405Sx-E CC1R5-2412Sx-E CC1R5-2412Dx-E Nominal Voltage V DC24 Voltage Range V DC18-36 Input Efficiency (typ) (*1) ％ 72 77 81 79 Current (typ) (*1) A 0.076 0.081 0.077 0.079 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 0.400 0.300 0.125 0.100 0.060 0.050 Maximum Power (*2) W 1.32 1.5 Maximum Line Regulation (Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature–40°C to +50°C) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 3.2 Mechanical Size (W x H x D) mm DIP: 16.51 x 8.5 x 16.6 / SMD: 16.51 x 8.8 x 16.6 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ITEMS/UNITS MODEL CC1R5-4803Sx-E CC1R5-4805Sx-E CC1R5-4812Sx-E CC1R5-4812Dx-E Nominal Voltage V DC48 Voltage Range V DC36-76 Input Efficiency (typ) (*1) ％ 70 76 80 79 Current (typ) (*1) A 0.039 0.041 0.039 0.040 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 0.400 0.300 0.125 0.100 0.060 0.050 Maximum Power (*2) W 1.32 1.5 Maximum Line Regulation (Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature–40°C to +50°C) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 3.2 Mechanical Size (W x H x D) mm DIP: 16.51 x 8.5 x 16.6 / SMD: 16.51 x 8.8 x 16.6 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ・All specifications are subject to change without notice.

CC1R5-E 4 Outline Drawing CC1R5-xxxxxF-E (DIP type) 16.6±0.2 Shape/Dimensions Recommended measurements for mounting board ax. 4.0 14.605 m 5 8. 2 9 Outer shape of 3.5 t=0.3 22. product 2.54 1162..571 2.7 13.08 10.16 7.6 7-ø1.0 (land diameter ø2.0) 5.082.54 1.905 12.7 1.905 a 0.5 2.54()3.22 3a b4 4 3.5 1.920-ø51.5 (land diameter ø2.5) 5 16.51 2 5 2. 1.0 8 0 b 7.62 7-0.3×0.6 6 5.54 2.7 Unit: mm )2 1 7 2. Allowable tolerance is ±0.5 if not specified separately. 3.2 b a ( CC1R5-xxxxxR-E (SMD type) 16.6±0.2 Shape/Dimensions Recommended measurements for mounting board 0 8.8max. 4.t=0.3 ()3.22 Opruotdeur csthape of 54 2 2. 1.8 1169..5811 1.8 Coplanarity: 0.1 or lower ()13.38 10.16 7.6 1.2 5.082.54 2.54()3.22 3 4 4 3.2 2125..06 3.2 5 2 5 2. 8 62 5.0 7. 7-0.3×0.6 6 4 5 )22 1 7 2. Unit: mm 3. Allowable tolerance is ±0.5 if not specified separately. ( Connection diagram CC1R5-xxxxSx-E CC1R5-xxxxDx-E Terminal connections Terminal connections +Vin 1 7 +Vout No.1 +Vin +Vin 1 7 +Vout No.1 +Vin L L 6 TRM oa No.2 RC 6 TRM oa No.2 RC RC2 5 –Vout d NNoo..34 –NVCin RC2 5 COM dLo NNoo..34 ––VVoinut No.5 –Vout a No.5 Common out –Vin 3 4NC No.6 TRM –Vin 3 4 –Vout d No.6 TRM No.7 +Vout No.7 +Vout Derating Curve 100 %)80 Natural air cooling a b er ( w60 o p ut 40 utp20 a:0.5m/s(100LFM) O b:1m/s(200LFM) 0 -40 -20　 0　 20　 40　60　80　100 Ambient temperature (°C) Output power derating by ambient temperature (common specification) ・All specifications are subject to change without notice.

CC3-E（DIP/SMD） 5 CC3-E Specifications ITEMS/UNITS MODEL CC3-0503Sx-E CC3-0505Sx-E CC3-0512Sx-E CC3-0512Dx-E Nominal Voltage V DC5.0 Voltage Range V DC4.5-9.0 Input Efficiency (typ) (*1) ％ 73 77 82 81 Current (typ) (*1) A 0.723 0.779 0.732 0.741 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 0.800 0.600 0.250 0.200 0.125 0.100 Maximum Power (*2) 2.64 3 Maximum Line Regulation(Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38℃ in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38℃ in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, X/Y/Z 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 4.5 Mechanical Size (W x H x D) mm DIP: 22.86 x 8.5 x 16.6 / SMD: 22.86 x 8.8 x 16.6 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ITEMS/UNITS MODEL CC3-1203Sx-E CC3-1205Sx-E CC3-1212Sx-E CC3-1212Dx-E Nominal Voltage V DC12 Voltage Range V DC9.0-18 Input Efficiency (typ) (*1) ％ 74 79 82 81 Current (typ) (*1) A 0.297 0.316 0.305 0.309 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 0.800 0.600 0.250 0.200 0.125 0.100 Maximum Power (*2) W 2.64 3 Maximum Line Regulation(Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, X/Y/Z 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 4.5 Mechanical Size (W x H x D) mm DIP: 22.86 x 8.5 x 16.6 / SMD: 22.86 x 8.8 x 16.6 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ・All specifications are subject to change without notice.

CC3-E（DIP/SMD） 6 ITEMS/UNITS MODEL CC3-2403Sx-E CC3-2405Sx-E CC3-2412Sx-E CC3-2412Dx-E Nominal Voltage V DC24 Voltage Range V DC18-36 Input Efficiency (typ) (*1) ％ 73 78 82 81 Current (typ) (*1) A 0.151 0.160 0.152 0.154 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 0.800 0.600 0.250 0.200 0.125 0.100 Maximum Power (*2) W 2.64 3 Maximum Line Regulation(Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, X/Y/Z 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 4.5 Mechanical Size (W x H x D) mm DIP: 22.86 x 8.5 x 16.6 / SMD: 22.86 x 8.8 x 16.6 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ITEMS/UNITS MODEL CC3-4803Sx-E CC3-4805Sx-E CC3-4812Sx-E CC3-4812Dx-E Nominal Voltage V DC48 Voltage Range V DC36-76 Input Efficiency (typ) (*1) ％ 73 79 81 80 Current (typ) (*1) A 0.075 0.079 0.077 0.078 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 0.800 0.600 0.250 0.200 0.125 0.100 Maximum Power (*2) W 2.64 3 Maximum Line Regulation(Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, X/Y/Z 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 4.5 Mechanical Size (W x H x D) mm DIP: 22.86 x 8.5 x 16.6 / SMD: 22.86 x 8.8 x 16.6 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ・All specifications are subject to change without notice.

CC3-E（DIP/SMD） 7 Outline Drawing CC3-xxxxxF-E (DIP type) 16.6±0.2 Shape/Dimensions Recommended measurements for mounting board ax. 4.0 20.32 m 5 8. 2 9 Outer shape of product 3.5 t=0.3 22. 2.54 2127..8768 2.7 13.08 10.16 7.6 7-ø1.0 (land diameter ø2.0) 5.082.54 2.54 17.78 2.54 a 0.5 2.54()3.22 32a b45 2.54 1.0 3.5 2.524-ø1.5 2(l2a.n8d6 diameter ø2.5) 08 b 2.7 62 5. 7. 7-0.3×0.6 6 4 5 )2 1 7 2.5 0. Unit: mm 3.2 b a Allowable tolerance is ±0.5 if not specified separately. ( CC3-xxxxxR-E (SMD type) 16.6±0.2 Shape/Dimensions Recommended measurements for mounting board 8.8max. 4.0t=0.3 ()23.22 Outer shape of product 2.54 22.86 Coplanarity: 0.1 or lower ()13.38 10.16 7.6 1.2 5.082.54 26.16 1.8 1.8 3.2 22.0 3.2 )2 28.4 2.54(3.2 3 4 4 5 2 5 2. 8 62 5.0 7. 7-0.3×0.6 6 4 5 )2 1 7 2. Unit: mm 3.2 Allowable tolerance is ±0.5 if not specified separately. ( Connection diagram CC3-xxxxSx-E CC3-xxxxDx-E Terminal connections Terminal connections +Vin +Vout +Vin +Vout 1 7 No.1 +Vin 1 7 No.1 +Vin 56 TRM Load NNoo..32 –RVCin 56 TRM Load NNoo..23 R–VCin RC2 –Vout No.4 NC RC2 COM Lo No.4 –Vout No.5 –Vout –Vout ad No.5 Common out –Vin 3 4NC No.6 TRM –Vin 3 4 No.6 TRM No.7 +Vout No.7 +Vout Derating Curve 100 %)80 Natural air cooling a b er ( w60 o p ut 40 utp20 a:0.5m/s(100LFM) O b:1m/s(200LFM) 0 -40 -20　 0　 20　 40　60　80　100 Ambient temperature (°C) Output power derating by ambient temperature (common specification) ・All specifications are subject to change without notice.

CC3-E（SIP） 8 CC3-E Specifications ITEMS/UNITS MODEL CC3-0503SS-E CC3-0505SS-E CC3-0512SS-E CC3-0512DS-E Nominal Voltage V DC5.0 Voltage Range V DC4.5-9.0 Input Efficiency (typ) (*1) ％ 73 77 82 81 Current (typ) (*1) A 0.723 0.779 0.732 0.741 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 0.800 0.600 0.250 0.200 0.125 0.100 Maximum Power (*2) W 2.64 3 Maximum Line Regulation (Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.67 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38℃ in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38℃ in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 7 Mechanical Size (W x H x D) mm 27.8 x 17.9 x 9.2 Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ITEMS/UNITS MODEL CC3-1205SS-E CC3-1212SS-E CC3-1212DS-E Nominal Voltage V DC12 Voltage Range V DC9.0-18 Input Efficiency (typ) (*1) ％ 79 82 Current (typ) (*1) A 0.316 0.305 Nominal Voltage VDC 5 12 15 12 15 Maximum Current A 0.600 0.250 0.200 0.125 0.100 Maximum Power (*2) W 3 Maximum Line Regulation (Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 7 Mechanical Size (W x H x D) mm 27.8 x 17.9 x 9.2 Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ・All specifications are subject to change without notice.

CC3-E（SIP） 9 ITEMS/UNITS MODEL CC3-2403SS-E CC3-2405SS-E CC3-2412SS-E CC3-2412DS-E Nominal Voltage V DC24 Voltage Range V DC18-36 Input Efficiency (typ) (*1) ％ 73 78 82 81 Current (typ) (*1) A 0.151 0.160 0.152 0.154 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 0.800 0.600 0.250 0.200 0.125 0.100 Maximum Power (*2) W 2.64 3 Maximum Line Regulation (Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.67 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 7 Mechanical Size (W x H x D) mm 27.8 x 17.9 x 9.2 Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ITEMS/UNITS MODEL CC3-4803SS-E CC3-4805SS-E CC3-4812DS-E Nominal Voltage V DC48 Voltage Range V DC36-76 Input Efficiency (typ) (*1) ％ 73 79 82 Current (typ) (*1) A 0.075 0.079 0.076 Nominal Voltage VDC 3.3 5 12 15 Maximum Current A 0.800 0.600 0.125 0.100 Maximum Power (*2) W 2.64 3 Maximum Line Regulation (Within input voltage range) mV 20 80 Maximum Load Regulation (0-100% load) (*3) mV 40 600 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 7 Mechanical Size (W x H x D) mm 27.8 x 17.9 x 9.2 Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ・All specifications are subject to change without notice.

CC3-E（SIP） 10 Outline Drawing CC3-xxxxxS-E (SIP type) Shape/Dimensions 9.2 9 7. 1 4 ()0.5 ()0.5 1(t=0.3) 0.5 4.1 3.5 2.47 P P P P 2P P P P 2.47 6 t=0.25 22.86 17.78 5.01 P=2.54 27.8 Recommended measurements for mounting board a 1 2 3 4 5 7 8 9 10 a 5 27.8 2 0. 2.47 22.86 2.47 9. 4 17.78 2-ø1.5 (land diameter ø2.5) P=2.54 Internal parts mounting space P P P P 2P P P P 0 Unit: mm 6. 2 Allowable tolerance is ±0.5 if not specified separately. 9. 9-ø0.8 (land diameter ø2.0) Connection diagram CC3-xxxxSS-E CC3-xxxxDS-E Terminal connections Terminal connections +Vout –Vout TRM RC –Vin +Vin +Vin NNoo..12 +NVCout +Vout COM COM –Vout TRM RC –Vin +Vin +Vin NNoo..12 +CVOoMut 1 2 3 4 5 7 8 9 10 No.3 NC 1 2 3 4 5 7 8 9 10 No.3 COM No.4 –Vout No.4 –Vout Load No.5 TRM No.5 TRM No.6 NC Load Load No.6 NC No.7 RC No.7 RC No.8 –Vin No.8 –Vin No.9 +Vin No.9 +Vin No.10+Vin No.10+Vin Derating Curve 100 %)80 Natural air cooling a b er ( w60 o p ut 40 utp20 a:0.5m/s(100LFM) O b:1m/s(200LFM) 0 -40 -20　 0　 20　 40　60　80　100 Ambient temperature (°C) Output power derating by ambient temperature (common specification) ・All specifications are subject to change without notice.

CC6-E 11 CC6-E Specifications ITEMS/UNITS MODEL CC6-0503Sx-E CC6-0505Sx-E CC6-0512Sx-E CC6-0512Dx-E Nominal Voltage V DC5.0 Voltage Range V DC4.5-9.0 Input Efficiency (typ) (*1) ％ 76 79 82 Current (typ) (*1) A 1.042 1.266 1.463 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 1.200 1.000 0.500 0.400 0.250 0.200 Maximum Power (*2) W 3.96 5 6 Maximum Line Regulation(Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38℃ in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38℃ in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 5.8 Mechanical Size (W x H x D) mm DIP: 22.86 x 8.5 x 21.1 / SMD: 22.86 x 8.8 x 21.1 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ITEMS/UNITS MODEL CC6-1203Sx-E CC6-1205Sx-E CC6-1212Sx-E CC6-1212Dx-E Nominal Voltage V DC12 Voltage Range V DC9.0-18 Input Efficiency (typ) (*1) ％ 78 82 85 Current (typ) (*1) A 0.423 0.610 0.588 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 1.200 0.500 0.400 0.250 0.200 Maximum Power (*2) W 3.96 6 Maximum Line Regulation(Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 5.8 Mechanical Size (W x H x D) mm DIP: 22.86 x 8.5 x 21.1 / SMD: 22.86 x 8.8 x 21.1 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ・All specifications are subject to change without notice.

CC6-E 12 ITEMS/UNITS MODEL CC6-2403Sx-E CC6-2405Sx-E CC6-2412Sx-E CC6-2412Dx-E Nominal Voltage V DC24 Voltage Range V DC18-36 Input Efficiency (typ) (*1) ％ 77 81 87 86 Current (typ) (*1) A 0.214 0.309 0.287 0.291 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 1.200 0.500 0.400 0.250 0.200 Maximum Power (*2) W 3.96 6 Maximum Line Regulation(Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 5.8 Mechanical Size (W x H x D) mm DIP: 22.86 x 8.5 x 21.1 / SMD: 22.86 x 8.8 x 21.1 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ITEMS/UNITS MODEL CC6-4803Sx-E CC6-4805Sx-E CC6-4812Sx-E CC6-4812Dx-E Nominal Voltage V DC48 Voltage Range V DC36-76 Input Efficiency (typ) (*1) ％ 77 81 86 Current (typ) (*1) A 0.107 0.154 0.145 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 1.200 0.500 0.400 0.250 0.200 Maximum Power (*2) W 3.96 6 Maximum Line Regulation(Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 5.8 Mechanical Size (W x H x D) mm DIP: 22.86 x 8.5 x 21.1 / SMD: 22.86 x 8.8 x 21.1 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ・All specifications are subject to change without notice.

CC6-E 13 Outline Drawing CC6-xxxxxF-E (DIP type) 21.1±0.2 Shape/Dimensions Recommended measurements for mounting board 20.32 5max. 4.0 2.63 2.54 8. Outer shape of product t=0.3 8 5 0 3. 6 5. 1 2127..8768 17.87 15.24 10. 7-ø1.0 (land diameter ø2.0) 5.08 2.7 8 2.54 2.54 b 0 5 5. ()2.93 3a b4 0.3.5 2-ø1.5 (land2 d2i.a8m6eter ø2.5) 08 7-0.3×0.6 08 5. 5. 1.0 2 5 08 a 2.7 6 5. 0.1 6 1 8 5 5.0 0. )93 1 b a7 Allowable tolerance is ±0.5 if not specified seUpanrita: tmelmy. 2. ( CC6-xxxxxR-E (SMD type) 21.1±0.2 Shape/Dimensions Recommended measurements for mounting board )3 0 9 x. 4. 2. a ( m 8.8 t=0.3 Outer shape of product 8 0 6 5. 1.8 2262..1866 1.8 Coplanarity: 0.1 or lower ()18.17 15.24 10.1 1.2 5.08 ()2.93 3 4 5.08 08 7-0.3×0.6 08 3.2 22.0 3.2 5. 5. 2 5 28.4 8 0 6 5. 0.1 6 1 8 0 5. )3 1 7 Unit: mm 2.9 Allowable tolerance is ±0.5 if not specified separately. ( Connection diagram CC6-xxxxSx-E CC6-xxxxDx-E Terminal connections Terminal connections +Vin 1 7 +Vout No.1 +Vin +Vin 1 7 +Vout No.1 +Vin 6 TRM Load NNoo..32 –RVCin 6 TRM Load NNoo..23 R–VCin 5 5 RC –Vout No.4 NC RC COM No.4 –Vout 2 No.5 –Vout 2 Loa No.5 Common out –Vout d 3 4NC No.6 TRM 3 4 No.6 TRM –Vin –Vin No.7 +Vout No.7 +Vout Derating Curve 100 %)80 Natural air cooling a b er ( w60 o p ut 40 utp20 a:0.5m/s(100LFM) O b:1m/s(200LFM) 0 -40 -20　 0　 20　 40　60　80　100 Ambient temperature (°C) Output power derating by ambient temperature (common specification) ・All specifications are subject to change without notice.

CC10-E 14 CC10-E Specifications ITEMS/UNITS MODEL CC10-0503Sx-E CC10-0505Sx-E CC10-0512Sx-E CC10-0512Dx-E Nominal Voltage V DC5.0 Voltage Range V DC4.5-9.0 Input Efficiency (typ) (*1) ％ 84 83 Current (typ) (*1) A 1.964 2.381 2.286 2.313 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 2.500 2.000 0.800 0.640 0.400 0.320 Maximum Power (*2) W 8.25 10 9.6 Maximum Line Regulation(Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38℃ in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38℃ in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 10 Mechanical Size (W x H x D) mm DIP: 35.56 x 8.5 x 22.6 / SMD: 35.56 x 8.8 x 22.6 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ITEMS/UNITS MODEL CC10-1203Sx-E CC10-1205Sx-E CC10-1212Sx-E CC10-1212Dx-E Nominal Voltage V DC12 Voltage Range V DC9.0-18 Input Efficiency (typ) (*1) ％ 84 86 88 86 Current (typ) (*1) A 0.318 0.969 1.136 1.047 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 2.500 2.000 1000 800 450 360 Maximum Power (*2) W 8.25 10 12 10.8 Maximum Line Regulation(Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 10 Mechanical Size (W x H x D) mm DIP: 35.56 x 8.5 x 22.6 / SMD: 35.56 x 8.8 x 22.6 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ・All specifications are subject to change without notice.

CC10-E 15 ITEMS/UNITS MODEL CC10-2403Sx-E CC10-2405Sx-E CC10-2412Sx-E CC10-2412Dx-E Nominal Voltage V DC24 Voltage Range V DC18-36 Input Efficiency (typ) (*1) ％ 84 86 87 86 Current (typ) (*1) A 0.409 0.484 0.575 0.523 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 2.500 2.000 1.000 0.800 0.450 0.360 Maximum Power (*2) W 8.25 10 12 10.8 Maximum Line Regulation(Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 10 Mechanical Size (W x H x D) mm DIP: 35.56 x 8.5 x 22.6 / SMD: 35.56 x 8.8 x 22.6 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ITEMS/UNITS MODEL CC10-4803Sx-E CC10-4805Sx-E CC10-4812Sx-E CC10-4812Dx-E Nominal Voltage V DC48 Voltage Range V DC36-76 Input Efficiency (typ) (*1) ％ 84 86 88 86 Current (typ) (*1) A 0.205 0.242 0.284 0.262 Nominal Voltage VDC 3.3 5 12 15 12 15 Maximum Current A 2.500 2.000 1.000 0.800 0.450 0.360 Maximum Power (*2) W 8.25 10 12 10.8 Maximum Line Regulation(Within input voltage range) mV 20 40 80 Maximum Load Regulation (0-100% load) (*3) mV 40 100 600 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV 200mV 300mV Max Power Total Regulation (max) (*4) ％ 3 5 Maximum Ripple & Noise (typ/max) (*5) mVp-p 40/120 30/120 Voltage Adjustable Range VDC 3.15-3.6 4.75-6.0 11.4-15.0 11.4- 15.0 Over Current Protection (*6) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 10 Mechanical Size (W x H x D) mm DIP: 35.56 x 8.5 x 22.6 / SMD: 35.56 x 8.8 x 22.6 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout. Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal). (*4) Output voltage includes input change, load change (balanced load), and temperature change. (*5) In 50MHz, Ta=25°C. (*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30 seconds. ・All specifications are subject to change without notice.

CC10-E 16 Outline Drawing CC10-xxxxxF-E (DIP type) Shape/Dimensions Recommended measurements for mounting board x. 22.6±0.2 30.48 a 8.5m 4.0 8 5.08 3.3 Outer shape of 3.5 3255..546 a 2.7 t=0.3 18.62 15.24 10.16 7-ø1.0 (lapnrdo dduiacmteter ø2.0) 5.085.0808 5. 5.08 25.4 5.08 0.5 2-ø1.5 (land diameter ø2.5) )8 86 a b 35.56 5.0(3. 3 4 08 b 2.7 )10.1668 217-b0.3×0.6 a 576 5.5.085.08 0.53.5 Allowable tolerance is ±0.5 if not specified seUpanrita: tmelmy. 3. 1.0 ( CC10-xxxxxR-E (SMD type) Shape/Dimensions Recommended measurements for mounting board 22.6±0.2 8.8max. 4.0t=0.3 ()3.68 Opruotdeur csthape of 8 1.8 3358..5866 1.8 Coplanarity: 0.1 or lower ()18.92 15.24 10.16 1.2 5.05.085.08 )8 86 5.0(3. 3 4 8 3.2 34.6 3.2 0 2 5 5.8 41.0 )810.16 17-0.3×0.6 76 5.05.08 Unit: mm 3.6 Allowable tolerance is ±0.5 if not specified separately. ( Connection diagram CC10-xxxxSx-E CC10-xxxxDx-E +Vin +Vout Terminal connections +Vin +Vout Terminal connections 1 7 1 7 6 TRM Load NNoo..12 +RVCin 6 TRM Load NNoo..12 +RVCin RC 5 –Vout No.3 –Vin RC 5 COM No.3 –Vin 2 No.4 NC 2 Loa No.4 –Vout 3 4NC No.5 –Vout 3 4 –Vout d No.5 Common out –Vin –Vin No.6 TRM No.6 TRM No.7 +Vout No.7 +Vout Derating Curve 100 %)80 Natural air cooling a b er ( w60 o p ut 40 utp20 a:0.5m/s(100LFM) O b:1m/s(200LFM) 0 -40 -20　 0　 20　 40　60　80　100 Ambient temperature (°C) Output power derating by ambient temperature (common specification) ・All specifications are subject to change without notice.

CC15-E 17 CC15-E Specifications ITEMS/UNITS MODEL CC15-2403Sx-E CC15-2405Sx-E Nominal Voltage V DC24 Voltage Range V DC18-36 Input Efficiency (typ) (*1) ％ 89 Current (typ) (*1) A 0.695 0.702 Nominal Voltage VDC 3.3 5 Maximum Current A 4.500 3.000 Maximum Power (*2) W 14.85 15 Maximum Line Regulation(Within input voltage range) mV 65 100 Maximum Load Regulation (0-100% load) mV 120 200 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV Max Power Total Regulation (max) (*3) ％ +5/-3 Maximum Ripple & Noise (typ/max) (*4) mVp-p 40/120 Voltage Adjustable Range Not available Over Current Protection (*5) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38℃ in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38℃ in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 12.5 Mechanical Size (W x H x D) mm DIP: 37.55 x 7.0 x 32.1 / SMD: 37.55 x 7.5 x 32.1 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) Output voltage includes input change, load change (balanced load), and temperature change. (*4) In 50MHz, Ta=25°C. (*5) Latch method Resumes by restarting input or resetting remote on/off. ・All specifications are subject to change without notice.

CC15-E 18 Outline Drawing CC15-xxxxxSF-E (DIP type) Shape/Dimensions Recommended measurements for mounting board 38.1 32.1 47 Outer shape of product x. 4. ma P 7.0 t=0.3 PP 10.16 3.0 6.075 3275..545 6.075 27.33 22.86 PPP 25-ø1.0 (land diameter ø2.0) PP ()4.62 190 a b1121 2.54 a 2.7 0.5 PP 2-ø1.5 (land diameter ø2.5) PPP 8 13 5 7 14 3. 6 15 5 16 1.0 6.075 2.54 432 17-0.3×0.6 10.16 b 0.5 31.43775.55 P=2.54 )2 1 17 2.7 (4.6 b a Unit: mm Allowable tolerance is ±0.5 if not specified separately. CC15-xxxxxSR-E (SMD type) Shape/Dimensions Recommended measurements for mounting board 38.1 32.1 47 Outer shape of product x. 4. a P 7.5m 40.9 Coplanarity: 0.1 or lot=w0e.3r 6 PPP 10.16 ()4.62 190 1121 2.54 27.33 22.8 PPP PPP 8 13 P 2 P 7 14 P 1. P 6 15 4 5 16 2.5 432 17-0.3×0.6 10.16 3.2 36.6 3.2 )62 1 17 43.0 P=2.54 4. (1.8 1.8 Unit: mm Allowable tolerance is ±0.5 if not specified separately. Connection diagram Terminal connections 1 17 RC 2 No.1 NC No.10 NC 3 No.2 NC No.11 NC 4 –Vout +Vin 5 16 No.3 RC No.12 +Vout 6 15 L No.4 NC No.13 +Vout 78 1143 oad No.5 NC No.14 +Vout 9 12 No.6 +Vin No.15 –Vout –Vin 10 11 +Vout No.7 +Vin No.16 –Vout No.8 –Vin No.17 NC No.9 –Vin Derating Curve 100 %)80 Natural air cooling a b er ( w60 o p ut 40 utp20 a:0.5m/s(100LFM) O b:1m/s(200LFM) 0 -40 -20　 0　 20　 40　60　80　100 Ambient temperature (°C) Output power derating by ambient temperature (common specification) ・All specifications are subject to change without notice.

CC25-E 19 CC25-E Specifications ITEMS/UNITS MODEL CC25-2403Sx-E CC25-2405Sx-E Nominal Voltage V DC24 Voltage Range V DC18-36 Input Efficiency (typ) (*1) ％ 90 Current (typ) (*1) A 1.146 1.157 Nominal Voltage VDC 3.3 5 Maximum Current A 7.500 5.000 Maximum Power (*2) W 24.75 25 Maximum Line Regulation (Within input voltage range) mV 65 100 Maximum Load Regulation (0-100% load) mV 120 200 Output Temperature Coefficient (Ambient temperature -40℃ to +50℃) 80mV Max Power Total Regulation (max) (*3) ％ +5/-3 Maximum Ripple & Noise (typ/max) (*4) mVp-p 40/120 Voltage Adjustable Range VDC Not available Over Current Protection (*5) Available Function Over Voltage Protection Not available Remote ON/OFF Control Available Operating Ambient Temperature ℃ -40 to +85 Storage Ambient Temperature ℃ -40 to +85 Operating Ambient Humidity ％RH 5-95 (the conditions of maximum 38℃ in wet bulb temperature and non-condensation should be ensured.) Environment Storage Ambient Humidity ％RH 5-95 (the conditions of maximum 38℃ in wet bulb temperature and non-condensation should be ensured.) Vibration 10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each Shock 980m/s² (100G), 6ms, 3 directions, 3 times for each, in non-operation Withstand Voltage Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute) Isolation Isolation Resistance Between input terminal and output terminal: 500VDC, 50MΩ min Standards Safety Standards UL60950-1, CSA C22.2 No.60950-1 (C-UL), EN60950-1 (NEMKO) Weight (typ) g 20 Mechanical Size (W x H x D) mm DIP: 42.65 x 7.0 x 44.9 / SMD: 42.65 x 7.5 x 44.9 Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names. Note: With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately. (*1) With nominal input voltage, maximum output current, and Ta=25°C. (*2) The maximum output power value is between -40°C and +50°C. For use in outside this temperature range, derating is needed. (*3) Output voltage includes input change, load change (balanced load), and temperature change. (*4) In 50MHz, Ta=25°C. (*5) Latch method Resumes by restarting input or resetting remote on/off. ・All specifications are subject to change without notice.

CC25-E 20 Outline Drawing CC25-xxxxSF-E (DIP type) Shape/Dimensions Recommended measurements for mounting board 43.2 44.9 2 5 max. 4. Outer shape of product 7.0 t=0.3 PP 16 3.0 6.075 4320..655 6.075 5.08PPP PP10. 08 11110321 a b 1111145678 ()4.67 b 2.7 0.53.5 40.08 35.56 5.08PPPP 25-ø1.0 (land diameter ø2.0) PPPPPPP 5. 9 19 1.0 P 2-ø1.5 (land diameter ø2.5) P 8 20 5 8 725-0.3×0.6 21 a 0. 5.0 6 2223 2.7 6.075 5 24 36.575 2.54 432 10.16 42.65 P=2.54 1 25 b a )7 Unit: mm 6 Allowable tolerance is ±0.5 if not specified separately. 4. ( CC25-xxxxSR-E (SMD type) Shape/Dimensions Recommended measurements for mounting board 43.2 44.9 2 5 max. t=0.3 4. Outer shape of product 5 7.1.8 46.0 1.8 Coplanarity: 0.1 or lower 8PPPP 10.16 5.0P PP 111321 111456 )67 40.08 35.56 5.08PP PPPP 08 10 1178 (4. P PP 5. 9 19 P P 8 20 P P 08 7 2212 5. 6 23 3.2 41.7 3.2 5 24 2.54 432 10.16 48.1 P=2.54 1 25 )67 Allowable tolerance is ±0.5 if not specified seUpanrita: tmelmy. 4. ( Connection diagram Terminal connections 12 2254 –Vout No.1 NC No.10 +Vin No.19 –Vout RC 3 23 No.2 NC No.11 +Vin No.20 –Vout 4 22 No.3 NC No.12 +Vin No.21 –Vout 5 21 –Vin 6 20 L No.4 RC No.13 NC No.22 –Vout 78 19 oad No.5 NC No.14 NC No.23 –Vout 9 18 No.6 NC No.15 +Vout No.24 –Vout 10 17 No.7 –Vin No.16 +Vout No.25 NC 11 16 12 15 No.8 –Vin No.17 +Vout +Vin 13 14 +Vout No.9 –Vin No.18 +Vout Derating Curve 100 %)80 Natural air cooling a b er ( w60 o p ut 40 utp20 a:0.5m/s(100LFM) O b:1m/s(200LFM) 0 -40 -20　 0　 20　 40　60　80　100 Ambient temperature (°C) Output power derating by ambient temperature (common specification) ・All specifications are subject to change without notice.

CC-E 21 CC-E Instruction Manual 1. Control functions/Protection functions/Connections 1. Remote On/Off terminal (RC) 1-2. O utput voltage adjusting ter- minal (TRM) (1.5-10W type) 1.5-10W type Output voltage can be set to the values shown in the figure Open collector is recommended as the connection system. below by connecting the TRM terminal to the -Vout termi- Consult us for use with other systems. nal. Use a transistor with "VCE: Vin or over" and "Ic: 1mA or When not using this function (always on), set the TRM ter- over". minal to open. Output is switched off by setting the RC terminal open, and Note that when the output voltage is set high by this func- switched on by setting the RC terminal to LOW (0-0.4V). tion, derating of output current is necessary according to the maximum power. +Vin +Vout RC control L DIP/SMDmodels signal RC oad Model name Open Connection to -Vout Fig. CC–xx03Sx–E 3.3V 3.6V 1 –Vin –Vout CC–xx05Sx–E 5V 6V 1 CC–xx12Sx–E 12V 15V 1 When not using this function (always on), short-circuit be- CC–xx12Dx–E ±12V ±15V 2 tween RC terminal and -Vin terminal. To be replaced with 1R5(1.5W), 3(3W), 6(6W), or 10(10W) for actual model names. +Vin +Vout Fig.1 When not 3.3V 3.6V using this RC Lo +Vin +Vout 5V +Vin +Vout 6V function ad 12V 15V (always on) L L –Vin –Vout TRM oa TRM oa d d –Vin –Vout –Vin –Vout 15/25W type Fig.2 +12V +15V Output is switched on by setting the RC terminal to open, +Vin +Vout +Vin +Vout and switched off by setting the RC terminal to HIGH (con- TRM Load TRM Load necting to Vin terminal). COM COM Load Load –Vin –Vout –Vin –Vout +Vin +Vout –12V –15V RC L SIPmodels RC o control ad Model name Model name Connection to -Vout Fig. signal CC3–xx03SS–E 3.3V 3.67V 3 –Vin –Vout CC3–xx05SS–E 5V 6V 3 CC3–xx12SS–E 12V 15V 3 When not using this function (always on), set the RC termi- CC3–xx12DS–E ±12V ±15V 4 nal to open. Fig.3 When not +Vin +Vout Vout Vout RM Vin Vin Vout Vout RM Vin Vin using this L + – T – + + – T – + RC o function a (always on) d Load 3.3V,5V,12V Load 3.67V,6V,15V –Vin –Vout Fig.4 Vout OM Vout RM Vin Vin Vout OM Vout RM Vin Vin + C – T – + + C – T – + Load Load Load Load +12V –12V +15V –15V ・All specifications are subject to change without notice.

CC-E 22 For the ±12V output model, Adding a resistance Rb between TRM terminal and 24V single output by making the COM terminal and TRM +Vout terminal , to set the output voltage low terminal open. And output voltage can be set to 30V single *5 Vout = 3.3 - 15.53/(39.6+Rb) [Rb≧62] output by making the COM terminal open and connecting *6 Vout = 5.01 - 52.55/(31.8+Rb) [Rb≧160] the TRM terminal to the -Vout terminal. *7 Vout = 12.01 - 431.1/(57+Rb) [Rb≧620] *8 Vout = 12.02 - 968.5/(103+Rb) [Rb≧1500] models Calculating connected resistance Ra, Rb (kΩ) from set out- Model name COM terminalTRM terminal Single output Fig. Open Open put voltage Vout (V) Open Connection to -Vout Adding a resistance Ra between TRM terminal and -Vout * To be replaced with 1R5(1.5W), 3(3W), 6(6W), or 10(10W) for actual model names. terminal, to set the output voltage high Fig.5 Fig.6 *1 Ra = 9.59/(Vout-3.3) - 32 *2 Ra = 17.64/(Vout-5.01) - 17.8 +Vin +Vout +Vin +Vout 24V 30V *3 Ra = 50.53/(Vout-12.01) - 16.9 TRM L TRM L o o *4 Ra = 53.55/(Vout-12.02) - 18 a a COM d COM d –Vin –Vout –Vin –Vout Adding a resistance Rb between TRM terminal and +Vout models terminal , to set the output voltage low Model name COM terminal TRM terminal Single output Fig. *5 Rb = 15.53/(3.3-Vout) - 39.6 Open Open *6 Rb = 52.55/(5.01-Vout) - 31.8 Open Connection to -Vout *7 Rb = 431.1/(12.01-Vout) - 57 *8 Rb = 968.5/(12.02-Vout) - 103 Fig.7 Fig.8 +Vout COM –Vout TRM –Vin +Vin +Vout COM –Vout TRM –Vin +Vin Fig.9 3.3〜3.6V Fig.10 *5,*6,*7 3.15〜3.3V +Vout 5〜6V +Vout 4.75〜5V 12〜15V 11.4〜12V Load 24V Load 30V TRM Ra Load TRM Rb Load –Vout –Vout 1-3. O utput voltage adjusting func- *1,*2,*3 tion (adding external resistance) Fig.11 Fig.12 +12〜+15V *8 +11.4〜+12V (1.5-10W type) +Vout +Vout Rb TRM Load TRM Load Output voltage can be varied in the range shown in the fig- COM COM Load Load ure below by connecting a resistance (Ra, Rb) between the Ra –Vout –Vout TRM terminal and the -Vout terminal or between the TRM –12〜–15V –11.4〜–12V *4 terminal and +Vout terminal. models Note that when the output voltage is set high, derating Connection between Connection between of output current is necessary according to the maximum Model name Fig. Fig. -Vout and Ra +Vout and Rb power. to to to to models to to Connection between Connection between to to Model name Fig. Fig. -Vout and Ra +Vout and Rb * To be replaced with 1R5(1.5W), 3(3W), 6(6W), or 10(10W) for actual model names. to to to to Calculating output voltage Vout (V) from connected resis- to to tance Ra, Rb (kΩ) to to Adding a resistance Ra between TRM terminal and -Vout * To be replaced with 1R5(1.5W), 3(3W), 6(6W), or 10(10W) for actual model names. terminal, to set the output voltage high Calculating output voltage Vout (V) from connected resis- *1 Vout = 3.3 + 1.04/(2.83+Ra) tance Ra, Rb (kΩ) *2 Vout = 5 + 12.75/(12.69+Ra) Adding a resistance Ra between TRM terminal and -Vout *3 Vout = 12 + 48.4/(16.18+Ra) terminal, to set the output voltage high *4 Vout = 12 + 54.7/(18+Ra) *1 Vout = 3.3 + 9.59/(32+Ra) *2 Vout = 5.01 + 17.64/(17.8+Ra) Adding a resistance Rb between TRM terminal and *3 Vout = 12.01 + 50.53/(16.9+Ra) +Vout terminal , to set the output voltage low *4 Vout = 12.02 + 53.55/(18+Ra) *5 Vout = 3.3 - 1.69/(3.66+Rb) [Rb≧7.6] *6 Vout = 5 - 12.78/(17.79+Rb) [Rb≧33.3] *7 Vout = 12 - 184.1/(35.54+Rb) [Rb≧271.3] *8 Vout = 12 -470.3/(61.75+Rb) [Rb≧722.1] ・All specifications are subject to change without notice.

CC-E 23 Calculating connected resistance Ra, Rb (kΩ) from set out- 1-5. Over voltage protection put voltage Vout (V) Adding a resistance Ra between TRM terminal and -Vout An over voltage protection function is not incorporated in terminal, to set the output voltage high the model. Be careful if an external voltage over the nomi- *1 Ra = 1.04/(Vout-3.3) - 2.83 nal voltage is applied, damage may be caused. *2 Ra = 12.75/(Vout-5) - 12.69 *3 Ra = 48.4/(Vout-12) - 16.18 1-6. Low input voltage protection *4 Ra = 54.7/(Vout-12) - 18 This series is equipped with the low input voltage protec- Adding a resistance Rb between TRM terminal and tion in order to prevent malfunction due to low input volt- +Vout terminal, to set the output voltage low age. The converter stops operation if the input voltage *5 Rb = 1.69/(3.3-Vout) - 3.66 become lower than the set voltage. The set ranges are *6 Rb = 12.78/(5-Vout) - 17.79 shown in the table below. *7 Rb = 184.1/(12-Vout) - 35.54 Model name Input voltage range Voltage range set for protection circuit to to *8 Rb = 470.3/(12-Vout) - 61.75 to to Fig.13 Fig.14 to to to to +Vout –Vout TRM +Vout –Vout TRM ttoo ttoo To be replaced with 1R5(1.5W), 3(3W), 6(6W), or 10(10W) for actual model names. Ra *1,*2,*3 Rb *5,*6,*7 Load 3.3〜3.67V、5〜6V、12〜15V Load The above setting value is fixed and cannot be adjusted 3.15〜3.3V、4.75〜5V、11.4〜12V externally. Fig.15 Fig.16 +Vout COM –Vout TRM +Vout COM –Vout TRM 1-7. Insulation withstand voltage The insulation withstand voltage between input and output, Load Load Ra *4 Rb *8 and between terminal and case, is AC500V. +12〜+15V –12〜–15V Load Load –11.4〜–12V +11.4〜+12V 1-8. Series/Parallel connections 1-4. Over current protection Series connection 1.5-10W type Serial connection is applicable by wiring as shown in the An over current protection circuit is incorporated in the figure below (left). If output voltage is not generated by this model, and if over current occurs, the output voltage is connection, connect a Schottky barrier diode in which the lowered. By removing the over current and shorted condi- forward voltage is possibly low. tions, the output voltage automatically resumes. Note that Also note that the Schottky barrier diode should have a if the over current status continues for 30 seconds or over, reverse voltage that is twice or over the value of the voltage the internal elements of the converter may be deteriorated between +Vout and -Vout. or damaged. The current value, from which it is judged as And the output current should be the same or lower than the an over current, is not to be lower than the nominal current nominal current value, whichever is smaller in the convert- value. Due to fold back characteristics of OCP, the output ers. may not rise up steady with constant current load or induc- tive load. +Vin +Vout +Vin +Vout 15/25W type –Vin –Vout L –Vin –Vout L o o a a d d +Vin +Vout +Vin +Vout An over current protection circuit is incorporated in the model, and if over current occurs, the output voltage is lowered and the converter is stopped and latched. The –Vin –Vout –Vin –Vout output voltage does not automatically resume even after removing the over current and shorted conditions. Parallel connection To resume output voltage, restart input or reset remote on/ Parallel connection is not applicable. off. The current value, from which it is judged as an over cur- rent, is not to be lower than the nominal current value. ・All specifications are subject to change without notice.

CC-E 24 2. Noise reduction methods 2-1. Output ripple noise measurement method 2-3. Output ripple & noise The measured value of the converter noise may differ de- To reduce Output ripple & noise, connect a capacitor to pending on the measurement method. Measurement should the output of the converter. In addition, reduction can be be conducted in a position close to the output terminal. enhanced if a π type filter is incorporated as shown in the When connecting a prove, do not allow a loop to be config- figure below. In this case, use of a coil with around 100µH ured in order not to pick up flux. is recommended. As well, note that the spike voltage greatly differs depend- ing on the ripple voltmeter and frequency band of the oscil- +Vin +Vout +Vin +Vout loscope. L L o o a a Our noise measurement is conducted by the wiring shown d d in the figure below and in the frequency band of 50MHz. –Vin –Vout –Vin –Vout 10mm 20mm When the distance to the load from the output of the con- +Vin +Vout A lout verter is long, connect the capacitor as close as possible Vout L VinV V 0.1µF oad to the load. To reduce output spike noise, connect a ceramic capacitor –Vout Iin A –Vin 50Ω coaxial cable with around 1µF to the output of the converter. 1.5m Ripple Oscilloscope or voltmeter +Vin +Vout 50MHz 50MHz End-point: 50Ω+0.1µF L 1 F o a d 2-2. Input ripple noise –Vin –Vout This series is equipped with a built-in capacitor for input. However, by connecting a capacitor with around 10µF, 2-4. Capacity of external capaci- input ripple noise and input return noise can be reduced. tor connected to output +Vin +Vout +Vin +Vout Note that if a capacitor with capacity over the value shown in the table below is connected to the output, or several L L o o ad ad capacitors with low impedance are connected in parallel, –Vin –Vout –Vin –Vout operation of the converter may become unstable. When the distance to the input of the converter from the Model name Electrostatic capacitance (µF) max. input power supply is long, attach a capacitor as close as possible to the input terminal. +Vin +Vout L o a d –Vin –Vout When the distance to the input of the converter from the input power supply is long, the impedance of the input line can become high, causing high spike noise. In this case, it is recommended to connect a capacitor as close as possible to the input of the DC-DC converter. ・All specifications are subject to change without notice.

CC-E 25 2-5. Common mode noise 2-6. Radiation noise For products other than with 10W, capacitors are not con- Radiation noise of the converter can be reduced by con- nected between the primary GND and the secondary GND. necting the case terminal to the input or output GND ter- To reduce common mode noise, connect a capacitor with minal. The effectiveness varies depending on the device. around 1000pF between the primary GND and the second- Check it on the actual device. ary GND, as shown in the figure below. Regarding wiring, use GND line and solid pattern for the In this case, note that if the capacitor that is connected is bottom of the converter as much as possible. too large, coupling capacitance between input and output - SMD models are not equipped with case terminals. becomes large. Also be careful about the withstand voltage of the capacitor (500V or over is desirable with consideration of the insula- tion withstand voltage). +Vin +Vout L o a d –Vin –Vout For products with 10W, capacitors with 1000pF are inter- nally connected between primary and secondary. 3. Soldering conditions/Cleaning conditions 3-1. Soldering conditions 3-2. Cleaning method ●Soldering conditions Board cleaning after soldering is not recommended. How- 　DIP models / SIP models ever, the cleaning fluids and conditions shown in the table Observe the following conditions in soldering board. below have been tested and proved to have no problem. Solder dip 260°C, 10s max., 1 time These fluids and conditions can be used. Soldering copper 380°C, 3smax., 1 time/PIN Cleaning fluids and test conditions Cleanthrough 750H SMD models (1) Cleaning (shaking) at 60°C for 4 minutes Lead-free soldering / High-temperature reflow process (2) Rinsing (shaking in water) at 60°C for 4 minutes Surface temperature of parts 30 20s (3) Rinsing (shaking in water) at ordinary temperature - 245˚C max. 40°C for 4 minutes 225˚C min. (4) Drying at 70°C for 6 minutes 180˚C Pine alpha ST100S 150˚C (1) Cleaning (shaking) at 60°C for 5 minutes (2) Rinsing (shaking in water) at 30°C for 3 minutes (3) Drying at 70°C for 6 minutes 1 to 3˚C/s 40 to 100s 1 to 4˚C/s 1 to 5˚C/s The reflow must be 1 time only. Terpene Cleaner EC-7R (Do not reflow with the on-board module on the motherboard underside.) (1) Cleaning (shaking) at 60°C for 5 minutes (2) Rinsing (shaking in IPA) at 30°C for 10 minutes (3) Drying at 70°C for 6 minutes Isopropyl alcohol (1) Ultrasonic waves at 60°C for 1 minute (2) Cool bath cleaning R.T. for 1 minute (3) Vapor cleaning at 83°C for 1 minutes Asahiklin AK-225AES (1) Ultrasonic waves at 50°C for 2 minutes (2) Cool bath cleaning R.T. for 2 minutes ・All specifications are subject to change without notice.

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: T DK-Lambda: CC10-0503SF-E CC10-0503SR-E CC10-0505SF-E CC10-0512DF-E CC10-0512DR-E CC10-0512SF-E CC10- 0512SR-E CC10-1203SF-E CC10-1203SR-E CC10-1205SR-E CC10-1212DF-E CC10-1212DR-E CC10-1212SF-E CC10-1212SR-E CC10-2403SF-E CC10-2403SR-E CC10-2405SF-E CC10-2405SR-E CC10-2412DF-E CC10- 2412DR-E CC10-2412SF-E CC10-2412SR-E CC10-4805SF-E CC10-4812DR-E CC10-4812SF-E CC10-4812SR-E CC15-2403SF-E CC15-2403SFH-E CC15-2403SFP-E CC15-2403SR-E CC15-2403SRH-E CC15-2403SRP-E CC15-2405SF-E CC15-2405SFH-E CC15-2405SFP-E CC15-2405SR-E CC15-2405SRH-E CC15-2405SRP-E CC15-2412SRH-E CC15-2412SRP-E CC15-2415SFH-E CC15-2415SRH-E CC15-2415SRP-E CC15-4803SFP-E CC15-4803SRH-E CC15-4803SRP-E CC15-4805SFH-E CC15-4805SFP-E CC15-4805SRH-E CC15-4812SFP-E CC15-4812SRH-E CC15-4812SRP-E CC15-4815SFH-E CC15-4815SFP-E CC15-4815SRH-E CC15-4815SRP-E CC1R5-0503SF-E CC1R5-0503SR-E CC1R5-0505SF-E CC1R5-0505SR-E CC1R5-0512DF-E CC1R5-0512DR-E CC1R5-0512SF-E CC1R5-0512SR-E CC1R5-1203SR-E CC1R5-1205SF-E CC1R5-1212DF-E CC1R5-1212DR-E CC1R5-1212SF-E CC1R5-1212SR-E CC1R5-2403SF-E CC1R5-2412DR-E CC1R5-2412SF-E CC1R5-2412SR-E CC1R5-4803SF-E CC1R5-4805SF-E CC1R5-4805SR-E CC1R5-4812DF-E CC1R5-4812DR-E CC1R5-4812SR-E CC25-2403SF-E CC25-2403SR-E CC25-2405SR-E CC3-0503SF-E CC3-0503SR-E CC3-0505SF-E CC3-0505SR-E CC3-0512DR-E CC3-0512SF-E CC3-0512SR-E CC3-1203SF-E CC3-1203SR-E CC3-1205SR-E CC3-1212DF-E CC3-1212DR-E CC3-1212SF-E CC3-1212SR-E CC3-2403SF-E CC3-2403SR-E CC3-2405SF-E