[ For General Electronic Equipment Notice for TAIYO YUDEN Products (General Environment) ] Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product information in this catalog is as of October 2017. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or use of our products. Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or equipment incorporating our products, which are caused under the conditions other than those specified in this catalog or individual product specification sheets. ■ Please contact TAIYO YUDEN for further details of product specifications as the individual product specification sheets are available. ■ Please conduct validation and verification of our products in actual condition of mounting and operating environment before using our products. ■ The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office equipment, information and communication equipment including, without limitation, mobile phone, and PC) and medical equipment classified as Class I or II by IMDRF. Please be sure to contact TAIYO YUDEN for further information before using the products for any equipment which may directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation, automotive powertrain control system, train control system, and ship control system, traffic signal equipment, disaster prevention equipment, medical equipment classified as Class III by IMDRF, highly public information network equipment including, without limitation, telephone exchange, and base station). Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g., aerospace equipment, aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control equipment, undersea equipment, military equipment). *Note: There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g., in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN. Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment. When our products are used even for high safety and/or reliability-required devices or circuits of general electronic equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to install a protection circuit as necessary. Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above. ■ Information contained in this catalog is intended to convey examples of typical performances and/or applications of our products and is not intended to make any warranty with respect to the intellectual property rights or any other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights. ■ Please note that the scope of warranty for our products is limited to the delivered our products themselves and TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products. Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in accordance with such agreement. ■ The contents of this catalog are applicable to our products which are purchased from our sales offices or authorized distributors (hereinafter“ TAIYO YUDEN’s official sales channel”). Please note that the contents of this catalog are not applicable to our products purchased from any seller other than TAIYO YUDEN’s official sales channel. ■ Caution for Export Some of our products listed in this catalog may require specific procedures for export according to“ U.S. Export Administration Regulations”,“ Foreign Exchange and Foreign Trade Control Law” of Japan, and other applicable regulations. Should you have any questions on this matter, please contact our sales staff. 18

WIRE-WOUND CHIP POWER INDUCTORS(CB SERIES) WIRE-WOUND CHIP POWER INDUCTORS（CB SERIES） REFLOW REFLOW ■PARTS NUMBER * Operating Temp.：-40～+105℃（Including self-generated heat） C B △ △ 2 0 1 2 T 1 0 0 M △ △ △ △ △＝Blank space ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ①Series name ④Packaging Code Series name Code Packaging CB Wound chip power inductor T Taping ②Characteristics ⑤Nominal inductance Code Characteristics Code △△ Standard （example） Nominal inductance［μH］ IN △C High current 1R0 1.0 D U △L Low profile 100 10 C MF Low loss 101 100 T ※R＝Decimal point O ③Dimensions（L×W） R S Dimensions ⑥Inductance tolerance ／ Code Type（inch） （L×W）［mm］ Code Inductance tolerance P 1608 1608（0603） 1.6×0.8 K ±10％ O W 2012 2012（0805） 2.0×1.25 M ±20％ 2016 2016（0806） 2.0×1.6 E R 2518 2518（1007） 2.5×1.8 ⑦Special code IN 3225 3225（1210） 3.2×2.5 Code Special code D △ Standard U R Low Rdc type C T O ⑧Internal code R S ■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY Recommended Land Patterns Surface Mounting W ・Mounting and soldering conditions should be checked beforehand. L ・Applicable soldering process to these products is reflow soldering only. Type A B C T MF1608 0.55 0.7 1.0 C 2012 0.60 1.0 1.45 e 2016 0.60 1.0 1.8 2518 0.60 1.5 2.0 3225 0.85 1.7 2.7 A B A Unit：mm Standard quantity［pcs］ Type L W T e Paper tape Embossed tape 1.6±0.2 0.8±0.2 0.8±0.2 0.45±0.15 CBMF1608 － 3000 （0.063±0.008） （0.031±0.008） （0.031±0.008） （0.016±0.006） 2.0±0.2 1.25±0.2 0.9±0.1 0.5±0.2 CB L2012 4000 － （0.079±0.008） （0.049±0.008） （0.035±0.004） （0.020±0.008） CB 2012 2.0±0.2 1.25±0.2 1.25±0.2 0.5±0.2 － 3000 CB C2012 （0.079±0.008） （0.049±0.008） （0.049±0.008） （0.020±0.008） CB 2016 2.0±0.2 1.6±0.2 1.6±0.2 0.5±0.2 － 2000 CB C2016 （0.079±0.008） （0.063±0.008） （0.063±0.008） （0.020±0.008） CB 2518 2.5±0.2 1.8±0.2 1.8±0.2 0.5±0.2 － 2000 CB C2518 （0.098±0.008） （0.071±0.008） （0.071±0.008） （0.020±0.008） 3.2±0.2 2.5±0.2 2.5±0.2 0.6±0.3 CB C3225 － 1000 （0.126±0.008） （0.098±0.008） （0.098±0.008） （0.024±0.012） Unit：mm（inch） i_wound_CB_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 18 81

■PARTS NUMBER ●1608（0603）type Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ ［MHｚ］（min.） Idc1 Idc2 CBMF1608T1R0M RoHS 1.0 ±20％ 100 0.09 290 770 7.96 CBMF1608T2R2M RoHS 2.2 ±20％ 80 0.17 190 560 7.96 CBMF1608T3R3M RoHS 3.3 ±20％ 60 0.22 170 500 7.96 CBMF1608T4R7M RoHS 4.7 ±20％ 45 0.24 145 470 7.96 CBMF1608T100[] RoHS 10 ±10％，±20％ 32 0.36 115 380 2.52 CBMF1608T220[] RoHS 22 ±10％，±20％ 16 1.0 70 230 2.52 CBMF1608T470[] RoHS 47 ±10％，±20％ 11 2.5 50 140 2.52 ●2012（0805）type Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ ［MHｚ］（min.） Idc1 Idc2 CB 2012T1R0M RoHS 1.0 ±20％ 100 0.15 500 900 7.96 CB 2012T2R2M RoHS 2.2 ±20％ 80 0.23 410 770 7.96 CB 2012T3R3M RoHS 3.3 ±20％ 55 0.30 330 650 7.96 IN CCBB 22001122TT46RR78MM RRooHHSS 46..78 ±±2200％％ 4358 00..4407 320500 558400 77..9966 D CB 2012T100[] RoHS 10 ±10％，±20％ 32 0.70 190 440 2.52 U CB 2012T100[]R RoHS 10 ±10％，±20％ 32 0.50 200 520 2.52 C CB 2012T150[] RoHS 15 ±10％，±20％ 28 1.3 170 320 2.52 T CB 2012T220[] RoHS 22 ±10％，±20％ 16 1.7 135 280 2.52 O CB 2012T470[] RoHS 47 ±10％，±20％ 11 3.7 90 190 2.52 R CB 2012T680[] RoHS 68 ±10％，±20％ 10 6.0 70 140 2.52 S ／ CB 2012T101[] RoHS 100 ±10％，±20％ 8 7.0 60 130 0.796 P O Nominal inductance Self-resonant DC Resistance Rated current　※）　［ｍA］ Measuring W Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ ［MHｚ］（min.） Idc1 Idc2 E CB C2012T1R0M RoHS 1.0 ±20％ 100 0.19 700 840 7.96 R CB C2012T2R2M RoHS 2.2 ±20％ 70 0.33 530 640 7.96 IN CB C2012T4R7M RoHS 4.7 ±20％ 45 0.50 360 520 7.96 D CB C2012T100[] RoHS 10 ±10％，±20％ 40 1.2 240 340 2.52 U CB C2012T220[] RoHS 22 ±10％，±20％ 16 3.7 170 190 2.52 C CB C2012T470[] RoHS 47 ±10％，±20％ 11 5.8 120 150 2.52 T O Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring R Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ S ［MHｚ］（min.） Idc1 Idc2 CB L2012T1R0M RoHS 1.0 ±20％ 100 0.15 620 950 0.1 CB L2012T2R2M RoHS 2.2 ±20％ 80 0.39 440 590 0.1 CB L2012T4R7M RoHS 4.7 ±20％ 45 0.66 275 490 0.1 CB L2012T100M RoHS 10 ±20％ 32 1.0 205 370 0.1 CB L2012T220M RoHS 22 ±20％ 23 2.1 150 250 0.1 CB L2012T470M RoHS 47 ±20％ 11 4.2 100 140 0.1 ●2016（0806）type Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ ［MHｚ］（min.） Idc1 Idc2 CB 2016T1R0M RoHS 1.0 ±20％ 100 0.09 600 1,100 7.96 CB 2016T1R5M RoHS 1.5 ±20％ 80 0.11 550 1,000 7.96 CB 2016T2R2M RoHS 2.2 ±20％ 70 0.13 510 1,000 7.96 CB 2016T3R3M RoHS 3.3 ±20％ 55 0.20 400 800 7.96 CB 2016T4R7M RoHS 4.7 ±20％ 45 0.25 340 740 7.96 CB 2016T6R8M RoHS 6.8 ±20％ 38 0.35 300 600 7.96 CB 2016T100[] RoHS 10 ±10％，±20％ 32 0.50 250 520 2.52 CB 2016T150[] RoHS 15 ±10％，±20％ 28 0.70 210 440 2.52 CB 2016T220[] RoHS 22 ±10％，±20％ 16 1.0 165 370 2.52 CB 2016T330[] RoHS 33 ±10％，±20％ 14 1.7 130 270 2.52 CB 2016T470[] RoHS 47 ±10％，±20％ 11 2.4 110 240 2.52 CB 2016T680[] RoHS 68 ±10％，±20％ 10 3.0 90 210 2.52 CB 2016T101[] RoHS 100 ±10％，±20％ 8 4.5 70 170 0.796 ・ [] Please specify the Inductance tolerance code（Ｋor Ｍ） ※）The saturation current value（Idc1） is the DC current value having inductance decrease down to 30%.（ at 20℃） ※）The temperature rise current value（Idc2） is the DC current value having temperature increase by 40℃.（ at 20℃） ※）The rated current value is following either Idc1 or Idc2, which is the lower one. i_wound_CB_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 82 18

■PARTS NUMBER Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ ［MHｚ］（min.） Idc1 Idc2 CB C2016T1R0M RoHS 1.0 ±20％ 100 0.10 1,100 1,100 7.96 CB C2016T1R5M RoHS 1.5 ±20％ 80 0.15 1,000 1,000 7.96 CB C2016T2R2M RoHS 2.2 ±20％ 70 0.20 750 720 7.96 CB C2016T3R3M RoHS 3.3 ±20％ 55 0.27 600 610 7.96 CB C2016T4R7M RoHS 4.7 ±20％ 45 0.37 550 530 7.96 CB C2016T6R8M RoHS 6.8 ±20％ 38 0.59 450 450 7.96 CB C2016T100[] RoHS 10 ±10％，±20％ 32 0.82 380 350 2.52 CB C2016T150[] RoHS 15 ±10％，±20％ 28 1.2 300 300 2.52 CB C2016T220[] RoHS 22 ±10％，±20％ 16 1.8 250 240 2.52 CB C2016T330[] RoHS 33 ±10％，±20％ 14 2.8 220 220 2.52 CB C2016T470[] RoHS 47 ±10％，±20％ 11 4.3 150 150 2.52 CB C2016T680[] RoHS 68 ±10％，±20％ 10 7.0 130 130 2.52 CB C2016T101[] RoHS 100 ±10％，±20％ 8 8.0 110 110 0.796 ●2518（1007）type Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Parts number EHS ［μH］ Inductance tolerance ［MfrHeqｚu］e（nmciny.） ［Ω］（±30％） SaturatIidocn1 current TemperatuIrdec 2rise current frequency［MHz］ IN CB 2518T1R0M RoHS 1.0 ±20％ 100 0.06 1,200 1,500 7.96 D CB 2518T1R5M RoHS 1.5 ±20％ 80 0.07 650 1,400 7.96 U CB 2518T2R2M RoHS 2.2 ±20％ 68 0.09 510 1,300 7.96 C CB 2518T3R3M RoHS 3.3 ±20％ 54 0.11 440 1,200 7.96 T O CB 2518T4R7MR RoHS 4.7 ±20％ 46 0.10 310 1,200 7.96 CB 2518T4R7M RoHS 4.7 ±20％ 46 0.13 340 1,100 7.96 R S CB 2518T6R8M RoHS 6.8 ±20％ 38 0.15 270 930 7.96 ／ CB 2518T100[] RoHS 10 ±10％，±20％ 30 0.25 250 820 2.52 P CB 2518T150[] RoHS 15 ±10％，±20％ 23 0.32 180 650 2.52 O CB 2518T220[] RoHS 22 ±10％，±20％ 19 0.50 165 580 2.52 W CB 2518T330[] RoHS 33 ±10％，±20％ 15 0.70 130 460 2.52 CB 2518T470[] RoHS 47 ±10％，±20％ 12 0.95 110 420 2.52 E R CB 2518T680[] RoHS 68 ±10％，±20％ 9.5 1.5 70 310 2.52 CB 2518T101[] RoHS 100 ±10％，±20％ 9.0 2.1 60 260 0.796 IN CB 2518T151[] RoHS 150 ±10％，±20％ 7.0 3.2 55 210 0.796 D CB 2518T221[] RoHS 220 ±10％，±20％ 5.5 4.5 50 180 0.796 U CB 2518T331[] RoHS 330 ±10％，±20％ 4.5 7.0 40 140 0.796 C CB 2518T471[] RoHS 470 ±10％，±20％ 3.5 10 35 120 0.796 T CB 2518T681[] RoHS 680 ±10％，±20％ 3.0 17 30 90 0.796 O CB 2518T102[] RoHS 1000 ±10％，±20％ 2.4 24 25 75 0.252 R S Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ ［MHｚ］（min.） Idc1 Idc2 CB C2518T1R0M RoHS 1.0 ±20％ 100 0.08 1,000 1,200 7.96 CB C2518T1R5M RoHS 1.5 ±20％ 80 0.11 950 1,190 7.96 CB C2518T2R2M RoHS 2.2 ±20％ 68 0.13 890 1,100 7.96 CB C2518T3R3M RoHS 3.3 ±20％ 54 0.16 730 1,020 7.96 CB C2518T4R7M RoHS 4.7 ±20％ 41 0.20 680 920 7.96 CB C2518T6R8M RoHS 6.8 ±20％ 38 0.30 550 740 7.96 CB C2518T100[] RoHS 10 ±10％，±20％ 30 0.36 480 680 2.52 CB C2518T150[] RoHS 15 ±10％，±20％ 23 0.65 350 500 2.52 CB C2518T220[] RoHS 22 ±10％，±20％ 19 0.77 320 460 2.52 CB C2518T330[] RoHS 33 ±10％，±20％ 15 1.5 270 320 2.52 CB C2518T470[] RoHS 47 ±10％，±20％ 12 1.9 240 290 2.52 CB C2518T680[] RoHS 68 ±10％，±20％ 9.5 2.8 200 200 2.52 CB C2518T101[] RoHS 100 ±10％，±20％ 9.0 3.7 160 170 0.796 CB C2518T151[] RoHS 150 ±10％，±20％ 7.0 6.1 140 130 0.796 CB C2518T221[] RoHS 220 ±10％，±20％ 5.5 8.4 115 110 0.796 CB C2518T331[] RoHS 330 ±10％，±20％ 4.5 12.3 100 90 0.796 CB C2518T471[] RoHS 470 ±10％，±20％ 3.5 22 80 70 0.796 CB C2518T681[] RoHS 680 ±10％，±20％ 3.0 28 65 60 0.796 ・ [] Please specify the Inductance tolerance code（Ｋor Ｍ） ※）The saturation current value（Idc1） is the DC current value having inductance decrease down to 30%.（ at 20℃） ※）The temperature rise current value（Idc2） is the DC current value having temperature increase by 40℃.（ at 20℃） ※）The rated current value is following either Idc1 or Idc2, which is the lower one. i_wound_CB_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 18 83

■PARTS NUMBER ●3225（1210）type Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ ［MHｚ］（min.） Idc1 Idc2 CB C3225T1R0MR RoHS 1.0 ±20％ 250 0.055 2,000 1,440 0.1 CB C3225T1R5MR RoHS 1.5 ±20％ 220 0.060 2,000 1,310 0.1 CB C3225T2R2MR RoHS 2.2 ±20％ 190 0.080 2,000 1,130 0.1 CB C3225T3R3MR RoHS 3.3 ±20％ 160 0.095 2,000 1,040 0.1 CB C3225T4R7MR RoHS 4.7 ±20％ 70 0.100 1,250 1,010 0.1 CB C3225T6R8MR RoHS 6.8 ±20％ 50 0.120 950 940 0.1 CB C3225T100[]R RoHS 10 ±10％，±20％ 23 0.133 900 900 0.1 CB C3225T150[]R RoHS 15 ±10％，±20％ 20 0.195 730 850 0.1 CB C3225T220[]R RoHS 22 ±10％，±20％ 17 0.27 620 780 0.1 CB C3225T330[]R RoHS 33 ±10％，±20％ 13 0.41 500 570 0.1 CB C3225T470[]R RoHS 47 ±10％，±20％ 10 0.67 390 480 0.1 CB C3225T680[]R RoHS 68 ±10％，±20％ 8.0 1.0 320 410 0.1 CB C3225T101[]R RoHS 100 ±10％，±20％ 6.0 1.4 270 340 0.1 CB C3225T221[]R RoHS 220 ±10％，±20％ 3.0 2.5 190 190 0.1 CB C3225T821[]R RoHS 820 ±10％，±20％ 1.8 12 110 110 0.1 CB C3225T102[]R RoHS 1000 ±10％，±20％ 1.6 13 100 100 0.1 IN ・ [] Please specify the Inductance tolerance code（Ｋor Ｍ） D U ※）The saturation current value（Idc1） is the DC current value having inductance decrease down to 30%.（ at 20℃） C ※）The temperature rise current value（Idc2） is the DC current value having temperature increase by 40℃.（ at 20℃） T ※）The rated current value is following either Idc1 or Idc2, which is the lower one. O R S ／ P O W E R IN D U C T O R S i_wound_CB_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 84 18

WIRE-WOUND CHIP INDUCTORS (LB SERIES)， WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES)， WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) ■PACKAGING ①Minimum Quantity Standard Quantity ［pcs］ Type Paper Tape Embossed Tape LB C3225 － 1000 CB C3225 LB 3218 － 2000 LB R2518 LB C2518 LB 2518 － 2000 CB 2518 CB C2518 LBM2016 LB C2016 LB 2016 － 2000 CB 2016 CB C2016 LB 2012 LB C2012 LB R2012 － 3000 CB 2012 CB C2012 CB L2012 4000 － LB 1608 4000 － LBMF1608 － 3000 CBMF1608 ②Tape material ●Embossed tape Top tape Chip Filled Sprocket hole Base tape Chip cavity Chip ●Card board carrier tape Top tape Base tape Chip Filled Sprocket hole Bottom tape Chip cavity Chip ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01

③Taping Dimensions ●Embossed Tape （0.315 inches wide） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） A B 3.5±0.05(0.138±0.002) 8.0±0.30.315±0.012) ( F 4.0±0.1 (0.157±0.004) 2.0±0.1 (0.079±0.004) Chip cavity Insertion pitch Tape thickness Type A B F T K 1.75±0.1 2.1±0.1 4.0±0.1 0.3±0.05 1.9max. LBM2016 （0.069±0.004） （0.083±0.004） （0.157±0.004） （0.012±0.002） （0.075max.） LB C3225 2.8±0.1 3.5±0.1 4.0±0.1 0.3±0.05 4.0max. CB C3225 （0.110±0.004） （0.138±0.004） （0.157±0.004） （0.012±0.002） （0.157max.） 2.1±0.1 3.5±0.1 4.0±0.1 0.3±0.05 2.2max. LB 3218 （0.083±0.004） （0.138±0.004） （0.157±0.004） （0.012±0.002） （0.087max.） LB 2518 CB 2518 2.15±0.1 2.7±0.1 4.0±0.1 0.3±0.05 2.2max. LB C2518 （0.085±0.004） （0.106±0.004） （0.157±0.004） （0.012±0.002） （0.087max.） CB C2518 LB R2518 LB 2016 CB 2016 1.75±0.1 2.1±0.1 4.0±0.1 0.3±0.05 1.9max. LB C2016 （0.069±0.004） （0.083±0.004） （0.157±0.004） （0.012±0.002） （0.075max.） CB C2016 LB 2012 CB 2012 1.45±0.1 2.25±0.1 4.0±0.1 0.25±0.05 1.45max. LB C2012 （0.057±0.004） （0.089±0.004） （0.157±0.004） （0.010±0.002） （0.057max.） CB C2012 LB R2012 LBMF1608 1.1±0.1 1.9±0.1 4.0±0.1 0.25±0.05 1.2max. CBMF1608 （0.043±0.004） （0.075±0.004） （0.157±0.004） （0.010±0.002） （0.047max.） Unit：mm（inch） ●Card board carrier tape（0.315 inches wide） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） T A B 3.5±0.05(0.138±0.002) 8.0±0.30.315±0.012) ( F 4.0±0.1 (0.157±0.004) 2.0±0.1 (0.079±0.004) Chip cavity Insertion pitch Tape thickness Type A B F T 1.55±0.1 2.3±0.1 4.0±0.1 1.1max. CB L2012 （0.061±0.004） （0.091±0.004） （0.157±0.004） （0.043max.） 1.0±0.1 1.8±0.1 4.0±0.1 1.1max. LB 1608 （0.039±0.004） （0.071±0.004） （0.157±0.004） （0.043max.） Unit：mm（inch） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01

④Leader and Blank Portion ⑤Reel Size ⑥Top Tape Strength The top tape requires a peel-off force 0.2 to 0.7N in the direction of the arrow as illustrated below. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01

WIRE-WOUND CHIP INDUCTORS (LB SERIES), WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES), WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) ■RELIABILITY DATA 1.Operating temperature Range LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series －40～＋105℃（Including self-generated heat） LBM Series 2. Storage Temperature Range（after soldering） LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series －40～＋85℃ LBM Series Test Methods and LB, CB Series： Remarks Please refer the term of "7. storage conditions" in precautions. 3.Rated Current LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series 4.Inductance LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series LB・LBC・LBR・CB・CBC・CBL・LBMF・CBMF・LBM Series Test Methods and Measuring equipment ：LCR Mater（HP4285A or its equivalent） Remarks Measuring frequency : Specified frequency 5.Q LB, LBC, LBR, LBMF Series － Specified Value CB, CBC, CBL, CBMF Series LBM Series Within the specified tolerance Test Methods and LBM Series Remarks Measuring equipment : LCR Mater（HP4285A or its equivalent） Measuring frequency : Specified frequency 6.DC Resisitance LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series Test Methods and Measuring equipment : DC Ohmmeter （HIOKI 3227 or its equivalent） Remarks 7.Self-Resonant Frequency LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series Test Methods and Measuring equipment : Impedance analyzer （HP4291A or its equivalent） Remarks ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01

8.Temperature Characteristic LBM2016 Inductance change : Within±5％ LB1608 LB2012 LBR2012 CB2012 CBL2012 LB2016 CB2016 LB2518 Inductance change : Within±20％ Specified Value LBR2518 CB2518 LBC3225 CBC3225 LBMF1608 CBMF1608 LBC2016 CBC2016 Inductance change : Within±25％ LBC2518 CBC2518 LB3218 LBC2012 CBC2012 Inductance change : Within±35％ Test Methods and Based on the inductance at 20℃ and Measured at the ambient of －40℃～＋85℃. Remarks 9.Rasistance to Flexure of Substrate LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series No damage. LBM Series Warp : 2mm（LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF Series） Test substrate : Glass epoxy-resin substrate Thickness : 0.8mm（LB1608・LBMF1608・CBMF1608） : 1.0mm（Others） Test Methods and Remarks 10.Body Strength LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series No damage. LBM Series LB・LBC・LBR・CB・CBC・CBL・LBM Applied force : 10N Test Methods and Duration : 10sec. Remarks LB1608・LBMF1608・CBMF1608 Applied force : 5N Duration : 10sec. 11.Adhesion of terminal electrode LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series No abnormality. LBM Series LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF Applied force : 10N to X and Y directions Duration : 5 sec. Test Methods and Test substrate : Printed board Remarks LB1608・CBMF1608・LBMF1608 Applied force : 5N to X and Y directions Duration : 5 sec. Test substrate : Printed board ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01

12.Resistance to vibration LB, LBC, LBR, LBMF Series Inductance change : Within±10％ CB, CBC, CBL, CBMF Series No significant abnormality in appearance. Specified Value Inductance change : Within±5％ LBM Series No significant abnormality in appearance. LB・LBR・LBC・CB・CBC・CBL・LBM・LBMF・CBMF： The given sample is soldered to the board and then it is tested depending on the conditions of the following table. Vibration Frequency 10～55Hz Test Methods and Total Amplitude 1.5mm (May not exceed acceleration 196m/s2) Remarks Sweeping Method 10Hz to 55Hz to 10Hz for 1min. X Time Y For 2 hours on each X, Y, and Z axis. Z Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 13.Drop test LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series － LBM Series 14.Solderability LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series At least 90％ of surface of terminal electrode is covered by new LBM Series LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF： Test Methods and Solder temperature : 245±5℃ Remarks Duration : 5±0.5sec Flux : Methanol solution with 25％ of colophony 15.Resistance to soldering LB, LBC, LBR, LBMF Series Inductance change : Within±10％ Specified Value CB, CBC, CBL, CBMF Series LBM Series Inductance change : Within±5％ Test Methods and LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF： Remarks 3 times of reflow oven at 230℃ MIN for 40sec. with peak temperature at 260 ℃ for 5sec. Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 16.Resisitance to solvent LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series － LBM Series Solvent temperature : Room temperature Test Methods and Type of solvent : Isopropyl alcohol Remarks Cleaning conditions : 90s. Immersion and cleaning. 17.Thermal shock LB, LBC, LBR, LBMF Series Inductance change : Within±10％ Specified Value CB, CBC, CBL, CBMF Series No significant abnormality in appearance. LBM Series Test Methods and LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF： Remarks The given sample is soldered to the board and then its Inductance is measured after 100cycles of the following conditions. Conditions of 1 cycle Step Temperature (℃) Duration (min) 1 －40±3 30±3 2 Room temperature Within 3 3 ＋85±2 30±3 4 Room temperature Within 3 Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01

18.Damp heat life test LB, LBC, LBR, LBMF Series Inductance change : Within±10％ Specified Value CB, CBC, CBL, CBMF Series No significant abnormality in appearance. LBM Series Temperature : 60±2℃ Test Methods and Humidity : 90～95％RH Remarks Duration : 1000 hrs Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 19.Loading under damp heat life test LB, LBC, LBR, LBMF Series Inductance change : Within±10％ CB, CBC, CBL, CBMF Series No significant abnormality in appearance. LBM Series Specified Value Test Methods and Temperature : 60±2℃ Remarks Humidity : 90～95％RH Duration : 1000 hrs Applied current : Rated current Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 20.High temperature life test LB, LBC, LBR, LBMF Series － Specified Value CB, CBC, CBL, CBMF Series Inductance change : Within±10％ LBM Series No significant abnormality in appearance. Temperature : 85±2℃ Test Methods and Duration : 1000 hrs Remarks Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 21.Loading at high temperature life test Inductance change : Within±10％ LB, LBC, LBR, LBMF Series （LBC3225 Series : Within±20％） No significant abnormality in appearance. Specified Value CB, CBC, CBL, CBMF Series － LBM Series Temperature : 85±2℃ Test Methods and Duration : 1000 hrs Remarks Applied current : Rated current Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 22.Low temperature life test LB, LBC, LBR, LBMF Series Inductance change : Within±10％ Specified Value CB, CBC, CBL, CBMF Series No significant abnormality in appearance. LBM Series Temperature : －40±2℃ Test Methods and Duration : 1000 hrs Remarks Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 23.Standard condition Standard test conditions LB, LBC, LBR, LBMF Series Unless specified, Ambient temperature is 20±15℃ and the Relative humidity is 65±20％. If there is any doubt about the test results, further Specified Value CB, CBC, CBL, CBMF Series measurement shall be had within the following limits: Ambient Temperature: 20±2℃ Relative humidity: 65±5％ LBM Series Inductance value is based on our standard measurement systems. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01

WIRE-WOUND CHIP INDUCTORS (LB SERIES)， WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES)， WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) ■PRECAUTIONS 1．Circuit Design ◆Operating environment 1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical Precautions equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2．PCB Design ◆Land pattern design Precautions 1. Please contact any of our offices for a land pattern, and refer to a recommended land pattern of a right figure or specifications. PRECAUTIONS 【Recommended Land Patterns】 Technical Surface Mounting considerations ・ Mounting and soldering conditions should be checked beforehand. ・ Applicable soldering process to those products is reflow soldering only. 3．Considerations for automatic placement ◆Adjustment of mounting machine Precautions 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. Technical 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. considerations 4．Soldering ◆Reflow soldering（ LB and CB Types） 1. For reflow soldering with either leaded or lead-free solder, the profile specified in "point for controlling" is recommended. Precautions ◆Recommended conditions for using a soldering iron 1. Put the soldering iron on the land-pattern. Soldering iron's temperature - Below 350℃ Duration-3 seconds or less. The soldering iron should not come in contact with inductor directly. ◆Reflow soldering（ LB and CB Types） 1. Reflow profile Technical considerations ◆Recommended conditions for using a soldering iron 1. Components can be damaged by excessive heat where soldering conditions exceed the specified range. 5．Cleaning ◆Cleaning conditions Precautions Washing by supersonic waves shall be avoided. Technical ◆Cleaning conditions considerations If washed by supersonic waves, the products might be broken. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_prec_e-E06R01

6．Handling ◆Handling 1. Keep the inductors away from all magnets and magnetic objects. ◆Breakaway PC boards（ splitting along perforations） 1. When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the Precautions board. 2. Board separation should not be done manually, but by using the appropriate devices. ◆Mechanical considerations 1. Please do not give the inductors any excessive mechanical shocks. ◆Handling 1. There is a case that a characteristic varies with magnetic influence. Technical ◆Breakaway PC boards（ splitting along perforations） considerations 1. Planning pattern configurations and the position of products should be carefully performed to minimize stress. ◆Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 7．Storage conditions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. ・ Recommended conditions Ambient temperature : 0～40℃ Precautions Humidity : Below 70% RH ・ The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, product should be used within 6 months from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. ◆Storage Technical 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes considerations and deterioration of taping/packaging materials may take place. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_prec_e-E06R01

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: T aiyo Yuden: CB2012T100K CB2012T100KR CB2012T100MR CB2012T101K CB2012T101M CB2012T150K CB2012T1R0M CB2012T220K CB2012T220M CB2012T2R2M CB2012T3R3M CB2012T470K CB2012T470M CB2012T4R7M CB2012T680K CB2012T6R8M CB2016T100K CB2016T100M CB2016T101K CB2016T101M CB2016T150K CB2016T1R0M CB2016T1R5M CB2016T220K CB2016T220M CB2016T2R2M CB2016T330K CB2016T3R3M CB2016T470K CB2016T470M CB2016T4R7M CB2016T680K CB2016T6R8M CB2518T100K CB2518T100M CB2518T101K CB2518T101M CB2518T102K CB2518T102M CB2518T150K CB2518T151K CB2518T1R0M CB2518T1R5M CB2518T220K CB2518T220M CB2518T221K CB2518T221M CB2518T2R2M CB2518T330K CB2518T331K CB2518T3R3M CB2518T470K CB2518T470M CB2518T471K CB2518T471M CB2518T4R7M CB2518T4R7MR CB2518T680K CB2518T681K CB2518T6R8M CBC2012T100K CBC2012T100M CBC2012T1R0M CBC2012T220K CBC2012T220M CBC2012T2R2M CBC2012T470K CBC2012T470M CBC2012T4R7M CBC2016T100K CBC2016T100M CBC2016T101K CBC2016T101M CBC2016T150K CBC2016T150M CBC2016T1R0M CBC2016T1R5M CBC2016T220K CBC2016T220M CBC2016T2R2M CBC2016T330K CBC2016T330M CBC2016T3R3M CBC2016T470K CBC2016T470M CBC2016T4R7M CBC2016T680K CBC2016T680M CBC2016T6R8M CBC2518T100K CBC2518T100M CBC2518T101K CBC2518T101M CBC2518T150K CBC2518T150M CBC2518T151K CBC2518T151M CBC2518T1R0M CBC2518T1R5M CBC2518T220K