[ For High Quality and/or Reliability Equipment Notice for TAIYO YUDEN Products (Automotive / Industrial Equipment) ] Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product information in this catalog is as of October 2017. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or use of our products. Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or equipment incorporating our products, which are caused under the conditions other than those specified in this catalog or individual product specification sheets. ■ Please contact TAIYO YUDEN for further details of product specifications as the individual product specification sheets are available. ■ Please conduct validation and verification of our products in actual condition of mounting and operating environment before using our products. ■ The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office equipment, information and communication equipment), medical equipment classified as Class I or II by IMDRF, industrial equipment, and automotive interior applications, etc. Please be sure to contact TAIYO YUDEN for further information before using the products for any equipment which may directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation, automotive powertrain control system, train control system, and ship control system, traffic signal equipment, medical equipment classified as Class III by IMDRF). Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g., aerospace equipment, aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control equipment, undersea equipment, military equipment). *Note: There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g., in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN. Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment. When our products are used even for high safety and/or reliability-required devices or circuits of general electronic equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to install a protection circuit as necessary. Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above. ■ Information contained in this catalog is intended to convey examples of typical performances and/or applications of our products and is not intended to make any warranty with respect to the intellectual property rights or any other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights. ■ Please note that the scope of warranty for our products is limited to the delivered our products themselves and TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products. Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in accordance with such agreement. ■ The contents of this catalog are applicable to our products which are purchased from our sales offices or authorized distributors (hereinafter“ TAIYO YUDEN’s official sales channel”). Please note that the contents of this catalog are not applicable to our products purchased from any seller other than TAIYO YUDEN’s official sales channel. ■ Caution for Export Some of our products listed in this catalog may require specific procedures for export according to“ U.S. Export Administration Regulations”,“ Foreign Exchange and Foreign Trade Control Law” of Japan, and other applicable regulations. Should you have any questions on this matter, please contact our sales staff. 18

WIRE-WOUND CHIP POWER INDUCTORS(CB SERIES) WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES) REFLOW ■PART NUMBER *Operating Temp. : -40～105℃（Including self-generated heat） C B △ △ 2 0 1 2 T 1 0 0 M △ V △＝Blank space ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ①Series name ④Packaging Code Series name Code Packaging CB Wound chip power inductor T Taping ②Characteristics ⑤Nominal inductance Code Characteristics Code Nominal inductance［μH］ △△ Standard （example） △C High current 1R0 1.0 100 10 ③Dimensions（L×W） 101 100 IN Dimensions ※R＝Decimal point Code Type（inch） D （L×W）［mm］ U 2012 2012（0805） 2.0×1.25 ⑥Inductance tolerance C 2016 2016（0806） 2.0×1.6 Code Inductance tolerance T O 2518 2518（1007） 2.5×1.8 K ±10％ R 3225 3225（1210） 3.2×2.5 M ±20％ S ／ ⑦Special code P O Code Special code W △ Standard E R Low Rdc type R IN ⑧Internal code D Code Internal code U V Inductor for Industrial and Automotive C T O R S ■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY Recommended Land Patterns Surface Mounting ・Mounting and soldering conditions should be checked beforehand. ・Applicable soldering process to these products is reflow soldering only. Type A B C 2012 0.60 1.0 1.45 2016 0.60 1.0 1.8 2518 0.60 1.5 2.0 3225 0.85 1.7 2.7 Unit：mm Standard quantity [pcs] Type L W T e Paper tape Embossed tape CB 2012 2.0±0.2 1.25±0.2 1.25±0.2 0.5±0.2 － 3000 CB C2012 （0.079±0.008） （0.049±0.008） （0.049±0.008） （0.020±0.008） CB 2016 2.0±0.2 1.6±0.2 1.6±0.2 0.5±0.2 － 2000 CB C2016 （0.079±0.008） （0.063±0.008） （0.063±0.008） （0.020±0.008） CB 2518 2.5±0.2 1.8±0.2 1.8±0.2 0.5±0.2 － 2000 CB C2518 （0.098±0.008） （0.071±0.008） （0.071±0.008） （0.020±0.008） 3.2±0.2 2.5±0.2 2.5±0.2 0.6±0.3 CB C3225 － 1000 （0.126±0.008） （0.098±0.008） （0.098±0.008） （0.024±0.012） Unit：mm（inch） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 18 55

■PART NUMBER ・ All the Wire-wound Chip Power Inductors of the catalog lineup are RoHS compliant. Note) ・ The exchange of individual specifications is necessary depending on the application and circuit condition. Please contact Taiyo Yuden sales channels. ・ *2: Industrial　products and Medical products 　 　Please consult with TAIYO YUDEN’s official sales channel for the details of the product specification , etc., 　　 and please review and　approve TAIYO YUDEN's product specification before ordering. Please be sure to contact us for further information before using the components for Automotive equipment. ●2012（0805）type Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Part number ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ Note ［MHｚ］（min.） Idc1 Idc2 CB 2012T1R0M V 1.0 ±20％ 100 0.15 500 700 7.96 *2 CB 2012T2R2M V 2.2 ±20％ 80 0.23 410 620 7.96 *2 CB 2012T3R3M V 3.3 ±20％ 55 0.30 330 550 7.96 *2 CB 2012T4R7M V 4.7 ±20％ 45 0.40 300 430 7.96 *2 CB 2012T6R8M V 6.8 ±20％ 38 0.47 250 350 7.96 *2 CB 2012T100[] V 10 ±10％，±20％ 32 0.70 190 300 2.52 *2 CB 2012T100[]RV 10 ±10％，±20％ 32 0.50 200 300 2.52 *2 CB 2012T150[] V 15 ±10％，±20％ 28 1.3 170 240 2.52 *2 CB 2012T220[] V 22 ±10％，±20％ 16 1.7 135 220 2.52 *2 IN CB 2012T470[] V 47 ±10％，±20％ 11 3.7 90 140 2.52 *2 D CB 2012T680[] V 68 ±10％，±20％ 10 6.0 70 100 2.52 *2 U CB 2012T101[] V 100 ±10％，±20％ 8 7.0 60 100 0.796 *2 C T Self-resonant Rated current　※）　［ｍA］ O Part number Nomina［lμ inHdu］ctance Inductance tolerance frequency D［ΩC ］R（e±sis3t0a％nc）e Saturation current Temperature rise current freqMueeanscuyr［inMgHz］ Note R ［MHｚ］（min.） Idc1 Idc2 S ／ CB C2012T1R0M V 1.0 ±20％ 100 0.19 700 640 7.96 *2 CB C2012T2R2M V 2.2 ±20％ 70 0.33 530 485 7.96 *2 P O CB C2012T4R7M V 4.7 ±20％ 45 0.50 360 395 7.96 *2 CB C2012T100[] V 10 ±10％，±20％ 40 1.2 240 255 2.52 *2 W CB C2012T220[] V 22 ±10％，±20％ 16 3.7 170 145 2.52 *2 E CB C2012T470[] V 47 ±10％，±20％ 11 5.8 120 115 2.52 *2 R IN ●2016（0806）type D Nominal inductance Self-resonant DC Resistance Rated current　※）　［ｍA］ Measuring U Part number ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ Note ［MHｚ］（min.） Idc1 Idc2 C T CB 2016T1R0M V 1.0 ±20％ 100 0.09 600 720 7.96 *2 O CB 2016T1R5M V 1.5 ±20％ 80 0.11 550 650 7.96 *2 R CB 2016T2R2M V 2.2 ±20％ 70 0.13 510 600 7.96 *2 S CB 2016T3R3M V 3.3 ±20％ 55 0.20 400 440 7.96 *2 CB 2016T4R7M V 4.7 ±20％ 45 0.25 340 410 7.96 *2 CB 2016T6R8M V 6.8 ±20％ 38 0.35 300 330 7.96 *2 CB 2016T100[] V 10 ±10％，±20％ 32 0.50 250 270 2.52 *2 CB 2016T150[] V 15 ±10％，±20％ 28 0.70 210 220 2.52 *2 CB 2016T220[] V 22 ±10％，±20％ 16 1.0 165 190 2.52 *2 CB 2016T330[] V 33 ±10％，±20％ 14 1.7 130 140 2.52 *2 CB 2016T470[] V 47 ±10％，±20％ 11 2.4 110 120 2.52 *2 CB 2016T680[] V 68 ±10％，±20％ 10 3.0 90 110 2.52 *2 CB 2016T101[] V 100 ±10％，±20％ 8 4.5 70 90 0.796 *2 Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Part number ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ Note ［MHｚ］（min.） Idc1 Idc2 CB C2016T1R0M V 1.0 ±20％ 100 0.10 1,100 885 7.96 *2 CB C2016T1R5M V 1.5 ±20％ 80 0.15 1,000 775 7.96 *2 CB C2016T2R2M V 2.2 ±20％ 70 0.20 750 625 7.96 *2 CB C2016T3R3M V 3.3 ±20％ 55 0.27 600 535 7.96 *2 CB C2016T4R7M V 4.7 ±20％ 45 0.37 550 460 7.96 *2 CB C2016T6R8M V 6.8 ±20％ 38 0.59 450 360 7.96 *2 CB C2016T100[] V 10 ±10％，±20％ 32 0.82 380 305 2.52 *2 CB C2016T150[] V 15 ±10％，±20％ 28 1.2 300 255 2.52 *2 CB C2016T220[] V 22 ±10％，±20％ 16 1.8 250 205 2.52 *2 CB C2016T330[] V 33 ±10％，±20％ 14 2.8 220 165 2.52 *2 CB C2016T470[] V 47 ±10％，±20％ 11 4.3 150 130 2.52 *2 CB C2016T680[] V 68 ±10％，±20％ 10 7.0 130 105 2.52 *2 CB C2016T101[] V 100 ±10％，±20％ 8 8.0 110 95 0.796 *2 ・ [] Please specify the Inductance tolerance code（Ｋor Ｍ） ※）The saturation current value（Idc1） is the DC current value having inductance decrease down to 30%.（ at 20℃） ※）The temperature rise current value（Idc2） is the DC current value having temperature increase by 20℃.（ at 20℃） ※）The rated current value is following either Idc1 or Idc2, which is the lower one. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 56 18

■PART NUMBER ●2518（1007）type Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Part number ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ Note ［MHｚ］（min.） Idc1 Idc2 CB 2518T1R0M V 1.0 ±20％ 100 0.06 1,200 1,250 7.96 *2 CB 2518T1R5M V 1.5 ±20％ 80 0.07 650 1,100 7.96 *2 CB 2518T2R2M V 2.2 ±20％ 68 0.09 510 1,000 7.96 *2 CB 2518T3R3M V 3.3 ±20％ 54 0.11 440 900 7.96 *2 CB 2518T4R7MRV 4.7 ±20％ 46 0.10 310 820 7.96 *2 CB 2518T4R7M V 4.7 ±20％ 46 0.13 340 820 7.96 *2 CB 2518T6R8M V 6.8 ±20％ 38 0.15 270 750 7.96 *2 CB 2518T100[] V 10 ±10％，±20％ 30 0.25 250 600 2.52 *2 CB 2518T150[] V 15 ±10％，±20％ 23 0.32 180 500 2.52 *2 CB 2518T220[] V 22 ±10％，±20％ 19 0.50 165 390 2.52 *2 CB 2518T330[] V 33 ±10％，±20％ 15 0.70 130 320 2.52 *2 CB 2518T470[] V 47 ±10％，±20％ 12 0.95 110 270 2.52 *2 CB 2518T680[] V 68 ±10％，±20％ 9.5 1.5 70 210 2.52 *2 CB 2518T101[] V 100 ±10％，±20％ 9.0 2.1 60 190 0.796 *2 CB 2518T151[] V 150 ±10％，±20％ 7.0 3.2 55 140 0.796 *2 CB 2518T221[] V 220 ±10％，±20％ 5.5 4.5 50 110 0.796 *2 CB 2518T331[] V 330 ±10％，±20％ 4.5 7.0 40 90 0.796 *2 CB 2518T471[] V 470 ±10％，±20％ 3.5 10 35 70 0.796 *2 CB 2518T681[] V 680 ±10％，±20％ 3.0 17 30 50 0.796 *2 CB 2518T102[] V 1000 ±10％，±20％ 2.4 24 25 45 0.252 *2 IN Nominal inductance Self-resonant DC Resistance Rated current　※）　［ｍA］ Measuring D Part number ［μH］ Inductance tolerance ［MfrHeqｚu］e（nmciny.） ［Ω］（±30％） SaturatIidocn1 current TemperatuIrdec 2rise current frequency［MHz］ Note U C CB C2518T1R0M V 1.0 ±20％ 100 0.08 1,000 775 7.96 *2 T CB C2518T1R5M V 1.5 ±20％ 80 0.11 950 730 7.96 *2 O CB C2518T2R2M V 2.2 ±20％ 68 0.13 890 630 7.96 *2 R CB C2518T3R3M V 3.3 ±20％ 54 0.16 730 560 7.96 *2 S CB C2518T4R7M V 4.7 ±20％ 41 0.20 680 510 7.96 *2 ／ CB C2518T6R8M V 6.8 ±20％ 38 0.30 550 420 7.96 *2 P CB C2518T100[] V 10 ±10％，±20％ 30 0.36 480 375 2.52 *2 O CB C2518T150[] V 15 ±10％，±20％ 23 0.65 350 285 2.52 *2 W CB C2518T220[] V 22 ±10％，±20％ 19 0.77 320 250 2.52 *2 E CB C2518T330[] V 33 ±10％，±20％ 15 1.5 270 185 2.52 *2 R CB C2518T470[] V 47 ±10％，±20％ 12 1.9 240 165 2.52 *2 CB C2518T680[] V 68 ±10％，±20％ 9.5 2.8 200 140 2.52 *2 IN CB C2518T101[] V 100 ±10％，±20％ 9.0 3.7 160 125 0.796 *2 D CB C2518T151[] V 150 ±10％，±20％ 7.0 6.1 140 95 0.796 *2 U CB C2518T221[] V 220 ±10％，±20％ 5.5 8.4 115 80 0.796 *2 C CB C2518T331[] V 330 ±10％，±20％ 4.5 12.3 100 65 0.796 *2 T CB C2518T471[] V 470 ±10％，±20％ 3.5 22 80 50 0.796 *2 O CB C2518T681[] V 680 ±10％，±20％ 3.0 28 65 45 0.796 *2 R S ●3225（1210）type Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Part number ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ Note ［MHｚ］（min.） Idc1 Idc2 CB C3225T1R0MRV 1.0 ±20％ 250 0.055 2,000 1,100 0.1 *2 CB C3225T1R5MRV 1.5 ±20％ 220 0.060 2,000 1,000 0.1 *2 CB C3225T2R2MRV 2.2 ±20％ 190 0.080 2,000 930 0.1 *2 CB C3225T3R3MRV 3.3 ±20％ 160 0.095 2,000 850 0.1 *2 CB C3225T4R7MRV 4.7 ±20％ 70 0.100 1,250 830 0.1 *2 CB C3225T6R8MRV 6.8 ±20％ 50 0.120 950 760 0.1 *2 CB C3225T100[]RV 10 ±10％，±20％ 23 0.133 900 720 0.1 *2 CB C3225T150[]RV 15 ±10％，±20％ 20 0.195 730 590 0.1 *2 CB C3225T220[]RV 22 ±10％，±20％ 17 0.27 620 500 0.1 *2 CB C3225T330[]RV 33 ±10％，±20％ 13 0.41 500 400 0.1 *2 CB C3225T470[]RV 47 ±10％，±20％ 10 0.67 390 320 0.1 *2 CB C3225T680[]RV 68 ±10％，±20％ 8.0 1.0 320 260 0.1 *2 CB C3225T101[]RV 100 ±10％，±20％ 6.0 1.4 270 220 0.1 *2 CB C3225T221[]RV 220 ±10％，±20％ 3.0 2.5 190 170 0.1 *2 CB C3225T821[]RV 820 ±10％，±20％ 1.8 12 110 80 0.1 *2 CB C3225T102[]RV 1000 ±10％，±20％ 1.6 13 100 75 0.1 *2 ・ [] Please specify the Inductance tolerance code（Ｋor Ｍ） ※）The saturation current value（Idc1） is the DC current value having inductance decrease down to 30%.（ at 20℃） ※）The temperature rise current value（Idc2） is the DC current value having temperature increase by 20℃.（ at 20℃） ※）The rated current value is following either Idc1 or Idc2, which is the lower one. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 18 57

■ Derating of Rated Current ●CB series Derating of current is necessary for CB series depending on ambient temperature. Please refer to the chart shown below for appropriate derating of current. CB 2012 type CB C2012 type CB 2016 type CB C2016 type 120 120 120 120 100 100 100 100 %) %) %) %) Ratio to rated current ( 86420000 IIddcc12 Ratio to rated current ( 86420000 IIddcc12 Ratio to rated current ( 86420000 IIddcc12 Ratio to rated current ( 86420000 IIddcc12 0 0 0 0 -40 -20 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 120 Ambient Temperature (℃) Ambient Temperature (℃) Ambient Temperature (℃) Ambient Temperature (℃) CB 2518 type CB C2518 type CB C3225 type 120 120 120 IN 100 100 100 %) %) %) DUCTORS／ Ratio to rated current ( 864200000 IIddcc12 Ratio to rated current ( 864200000 IIddcc12 Ratio to rated current ( 864200000 IIddcc12 -40 -20 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 120 P Ambient Temperature (℃) Ambient Temperature (℃) Ambient Temperature (℃) O W E R IN D U C T O R S ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 58 18

WIRE-WOUND CHIP INDUCTORS (LB SERIES)， WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES)， WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) ■PACKAGING ①Minimum Quantity Standard Quantity ［pcs］ Type Paper Tape Embossed Tape LB C3225 － 1000 CB C3225 LB 3218 － 2000 LB R2518 LB C2518 LB 2518 － 2000 CB 2518 CB C2518 LBM2016 LB C2016 LB 2016 － 2000 CB 2016 CB C2016 LB 2012 LB C2012 LB R2012 － 3000 CB 2012 CB C2012 CB L2012 4000 － LB 1608 4000 － LBMF1608 － 3000 CBMF1608 ②Tape material ●Embossed tape Top tape Chip Filled Sprocket hole Base tape Chip cavity Chip ●Card board carrier tape Top tape Base tape Chip Filled Sprocket hole Bottom tape Chip cavity Chip ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01

③Taping Dimensions ●Embossed Tape （0.315 inches wide） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） A B 3.5±0.05(0.138±0.002) 8.0±0.30.315±0.012) ( F 4.0±0.1 (0.157±0.004) 2.0±0.1 (0.079±0.004) Chip cavity Insertion pitch Tape thickness Type A B F T K 1.75±0.1 2.1±0.1 4.0±0.1 0.3±0.05 1.9max. LBM2016 （0.069±0.004） （0.083±0.004） （0.157±0.004） （0.012±0.002） （0.075max.） LB C3225 2.8±0.1 3.5±0.1 4.0±0.1 0.3±0.05 4.0max. CB C3225 （0.110±0.004） （0.138±0.004） （0.157±0.004） （0.012±0.002） （0.157max.） 2.1±0.1 3.5±0.1 4.0±0.1 0.3±0.05 2.2max. LB 3218 （0.083±0.004） （0.138±0.004） （0.157±0.004） （0.012±0.002） （0.087max.） LB 2518 CB 2518 2.15±0.1 2.7±0.1 4.0±0.1 0.3±0.05 2.2max. LB C2518 （0.085±0.004） （0.106±0.004） （0.157±0.004） （0.012±0.002） （0.087max.） CB C2518 LB R2518 LB 2016 CB 2016 1.75±0.1 2.1±0.1 4.0±0.1 0.3±0.05 1.9max. LB C2016 （0.069±0.004） （0.083±0.004） （0.157±0.004） （0.012±0.002） （0.075max.） CB C2016 LB 2012 CB 2012 1.45±0.1 2.25±0.1 4.0±0.1 0.25±0.05 1.45max. LB C2012 （0.057±0.004） （0.089±0.004） （0.157±0.004） （0.010±0.002） （0.057max.） CB C2012 LB R2012 LBMF1608 1.1±0.1 1.9±0.1 4.0±0.1 0.25±0.05 1.2max. CBMF1608 （0.043±0.004） （0.075±0.004） （0.157±0.004） （0.010±0.002） （0.047max.） Unit：mm（inch） ●Card board carrier tape（0.315 inches wide） φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） T A B 3.5±0.05(0.138±0.002) 8.0±0.30.315±0.012) ( F 4.0±0.1 (0.157±0.004) 2.0±0.1 (0.079±0.004) Chip cavity Insertion pitch Tape thickness Type A B F T 1.55±0.1 2.3±0.1 4.0±0.1 1.1max. CB L2012 （0.061±0.004） （0.091±0.004） （0.157±0.004） （0.043max.） 1.0±0.1 1.8±0.1 4.0±0.1 1.1max. LB 1608 （0.039±0.004） （0.071±0.004） （0.157±0.004） （0.043max.） Unit：mm（inch） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01

④Leader and Blank Portion ⑤Reel Size ⑥Top Tape Strength The top tape requires a peel-off force 0.2 to 0.7N in the direction of the arrow as illustrated below. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01

WIRE-WOUND CHIP INDUCTORS (LB SERIES), WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES), WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) ■RELIABILITY DATA 1.Operating temperature Range LB, LBC, LBR Series Specified Value CB, CBC Series －40～＋105℃（Including self-generated heat） LBM Series Test Methods and Including self-generated heat Remarks 2. Storage Temperature Range（after soldering） LB, LBC, LBR Series Specified Value CB, CBC Series －40～＋85℃ LBM Series Test Methods and LB, CB Series： Remarks Please refer the term of "7. storage conditions" in precautions. 3.Rated Current LB, LBC, LBR Series Specified Value CB, CBC Series Within the specified tolerance LBM Series 4.Inductance LB, LBC, LBR Series Specified Value CB, CBC Series Within the specified tolerance LBM Series Test Methods and LB・LBC・LBR・CB・CBC・LBM Series Remarks Measuring equipment ：LCR Mater（HP4285A or its equivalent） 5.Q LB, LBC, LBR Series － Specified Value CB, CBC Series LBM Series Within the specified tolerance Test Methods and LBM Series Remarks Measuring equipment : LCR Mater（HP4285A or its equivalent） 6.DC Resistance LB, LBC, LBR Series Specified Value CB, CBC Series Within the specified tolerance LBM Series Test Methods and Measuring equipment : DC Ohmmeter （HIOKI 3227 or its equivalent） Remarks 7.Self-Resonant Frequency LB, LBC, LBR Series Specified Value CB, CBC Series Within the specified tolerance LBM Series Test Methods and Measuring equipment : Impedance analyzer （HP4291A or its equivalent） Remarks ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_i_wound_CB_LB_reli_e.doc

8.Temperature Characteristic LBM2016 Inductance change : Within±10％ LB2012 LBR2012 CB2012 LB2016 CB2016 LB2518 LBR2518 CB2518 Inductance change : Within±20％ Specified Value LBC3225 CBC3225 LBC2016 CBC2016 LBC2518 CBC2518 Inductance change : Within±25％ LB3218 LBC2012 CBC2012 Inductance change : Within±35％ Change of maximum inductance deviation in step 1-5 Temperature（℃） Step LB, CB Serie Test Methods and 1 20 Remarks 2 －40 3 20（Reference temperature） 4 ＋85（Maximum operating temperature） 5 20 9.Rasistance to Flexure of Substrate LB, LBC, LBR Series Specified Value CB, CBC Series No damage. LBM Series Warp : 2mm（LB・LBC・LBR・CB・CBC・LBM Series） Test substrate : Board according to JIS C0051 Thickness : 1.0mm Test Methods and Remarks 10.Body Strength LB, LBC, LBR Series Specified Value CB, CBC Series No damage. LBM Series LB・LBC・LBR・CB・CBC・LBM Test Methods and Applied force : 10N Remarks Duration : 10sec. 11.Adhesion of terminal electrode LB, LBC, LBR Series Specified Value CB, CBC Series No abnormality. LBM Series LB・LBC・LBR・CB・CBC・CBL・LBM Test Methods and Applied force : 10N to X and Y directions Remarks Duration 5 sec. Test substrate : Printed board ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_i_wound_CB_LB_reli_e.doc

12.Resistance to vibration LB, LBC, LBR Series Inductance change : Within±20％ CB, CBC Series No significant abnormality in appearance. Specified Value Inductance change : Within±20％ LBM Series No significant abnormality in appearance. LB・LBR・LBC・CB・CBC・LBM : According to JIS C5102 clause 8.2. Vibration type : A Directions : 2 hrs each in X, Y and Z directions. Total：6 hrs Test Methods and Frequency range : 10 to 55 to 10 Hz（1min.） Remarks Amplitude : 1.5mm Mounting method : Soldering onto printed board Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 13.Drop test LB, LBC, LBR Series Specified Value CB, CBC Series － LBM Series 14.Solderability LB, LBC, LBR Series Specified Value CB, CBC Series At least 90％ of surface of terminal electrode is covered by new LBM Series LB・LBC・LBR・CB・CBC・CBL・LBM： Test Methods and Solder temperature : 245±5℃ Remarks Duration : 5±0.5sec Flux : Methanol solution with 25％ of colophony 15.Resistance to soldering LB, LBC, LBR Series Inductance change : Within±20％ Specified Value CB, CBC Series LBM Series Inductance change : Within±20％ Test Methods and LB・LBC・LBR・CB・CBC・CBL・LBM： Remarks 3 times of reflow oven at 230℃ MIN for 40sec. with peak temperature at 260 ℃ for 5sec. 16.Resisitance to solvent LB, LBC, LBR Series Specified Value CB, CBC Series － LBM Series Solvent temperature : Room temperature Test Methods and Type of solvent : Isopropyl alcohol Remarks Cleaning conditions : 90s. Immersion and cleaning. 17.Thermal shock LB, LBC, LBR Series Inductance change : Within±20％ Specified Value CB, CBC Series No significant abnormality in appearance. LBM Series Test Methods and LB・LBC・LBR・CB・CBC・CBL・LBM：－40～＋85℃, maintain times 30min. ,100 cycle Remarks Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_i_wound_CB_LB_reli_e.doc

18.Damp heat life test LB, LBC, LBR Series Inductance change : Within±20％ Specified Value CB, CBC Series No significant abnormality in appearance. LBM Series Temperature : 60±2℃ Test Methods and Humidity : 90～95％RH Remarks Duration : 1000 hrs Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 19.Loading under damp heat life test LB, LBC, LBR Series Inductance change : Within±20％ Specified Value CB, CBC Series No significant abnormality in appearance. LBM Series Temperature : 60±2℃ Humidity : 90～95％RH Test Methods and Duration : 1000 hrs Remarks Applied current : Rated current Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 20.High temperature life test LB, LBC, LBR Series － Specified Value CB, CBC Series Inductance change : Within±20％ LBM Series No significant abnormality in appearance. Temperature : 85±2℃ Test Methods and Duration : 1000 hrs Remarks Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 21.Loading at high temperature life test Inductance change : Within±20％ LB, LBC, LBR Series No significant abnormality in appearance. Specified Value CB, CBC Series － LBM Series Temperature : 85±2℃ Test Methods and Duration : 1000 hrs Remarks Applied current : Rated current Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 22.Low temperature life test LB, LBC, LBR Series Inductance change : Within±20％ Specified Value CB, CBC Series No significant abnormality in appearance. LBM Series Temperature : －40±2℃ Test Methods and Duration : 1000 hrs Remarks Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 23.Standard condition LB, LBC, LBR Series Standard test conditions Unless specified, Ambient temperature is 20±15℃ and the Relative CB, CBC Series humidity is 65±20％. If there is any doubt about the test results, further Specified Value measurement shall be had within the following limits: Ambient Temperature: 20±2℃ LBM Series Relative humidity: 65±5％ Inductance value is based on our standard measurement systems. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_i_wound_CB_LB_reli_e.doc

WIRE-WOUND CHIP INDUCTORS (LB SERIES)， WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES)， WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) ■PRECAUTIONS 1．Circuit Design ◆Operating environment 1. The products listed in this catalogue are intended for use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office equipment, information and communication equipment), general medical equipment, industrial equipment, and automotive interior applications, etc. Precautions Please be sure to contact TAIYO YUDEN for further information before using the products for any equipment which may directly cause loss of human life or bodily injury (e.g., specially controlled medical equipment, transportation equipment including, without limitation, automotive powertrain control system, train control system, and ship control system, traffic signal equipment). Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g., aerospace equipment, aviation equipment, nuclear control equipment, undersea equipment, military equipment, etc.). 2．PCB Design ◆Land pattern design Precautions 1. Please contact any of our offices for a land pattern, and refer to a recommended land pattern of a right figure or specifications. PRECAUTIONS 【Recommended Land Patterns】 Technical Surface Mounting considerations ・ Mounting and soldering conditions should be checked beforehand. ・ Applicable soldering process to those products is reflow soldering only. 3．Considerations for automatic placement ◆Adjustment of mounting machine Precautions 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. Technical 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. considerations 4．Soldering ◆Reflow soldering（ LB and CB Types） 1. For reflow soldering with either leaded or lead-free solder, the profile specified in "point for controlling" is recommended. Precautions ◆Recommended conditions for using a soldering iron 1. Put the soldering iron on the land-pattern. Soldering iron's temperature - Below 350℃ Duration-3 seconds or less. The soldering iron should not come in contact with inductor directly. ◆Reflow soldering（ LB and CB Types） 1. Reflow profile Technical considerations ◆Recommended conditions for using a soldering iron 1. Components can be damaged by excessive heat where soldering conditions exceed the specified range. 5．Cleaning ◆Cleaning conditions Precautions Washing by supersonic waves shall be avoided. Technical ◆Cleaning conditions considerations If washed by supersonic waves, the products might be broken. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_i_wound_CB_LB_prec_e.doc

6．Handling ◆Handling 1. Keep the inductors away from all magnets and magnetic objects. ◆Breakaway PC boards（ splitting along perforations） 1. When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the Precautions board. 2. Board separation should not be done manually, but by using the appropriate devices. ◆Mechanical considerations 1. Please do not give the inductors any excessive mechanical shocks. ◆Handling 1. There is a case that a characteristic varies with magnetic influence. Technical ◆Breakaway PC boards（ splitting along perforations） considerations 1. Planning pattern configurations and the position of products should be carefully performed to minimize stress. ◆Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 7．Storage conditions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. Precautions ・ Recommended conditions Ambient temperature：0～40℃ / Humidity：Below 70% RH The ambient temperature must be kept below 30℃ even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, These series should be used within 6 months from the time of delivery. ◆Storage Technical 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes considerations and deterioration of taping/packaging materials may take place. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . hq_i_wound_CB_LB_prec_e.doc

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: T aiyo Yuden: CBC3225T4R7MRV CB2016T4R7MV CBC3225T2R2MRV CBC3225T1R0MRV CBC2518T4R7MV CBC2012T2R2MV CBC3225T220KRV CB2016T220MV CBC2016T2R2MV CBC2012T1R0MV CB2518T1R0MV CB2518T4R7MV CB2518T220KV CB2016T101KV CB2012T4R7MV CBC3225T470KRV CB2016T470MV CB2016T220KV CB2016T2R2MV CB2012T2R2MV CB2518T100KV CB2016T470KV CB2012T100KRV CBC2518T100KV CB2016T1R0MV CBC2518T1R0MV CB2012T1R0MV CB2518T2R2MV CB2518T4R7MRV CBC2518T2R2MV CBC2016T1R0MV CBC3225T100KRV CB2012T100KV CB2016T100KV