[ For General Electronic Equipment Notice for TAIYO YUDEN Products (General Environment) ] Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product information in this catalog is as of October 2017. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or use of our products. Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or equipment incorporating our products, which are caused under the conditions other than those specified in this catalog or individual product specification sheets. ■ Please contact TAIYO YUDEN for further details of product specifications as the individual product specification sheets are available. ■ Please conduct validation and verification of our products in actual condition of mounting and operating environment before using our products. ■ The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office equipment, information and communication equipment including, without limitation, mobile phone, and PC) and medical equipment classified as Class I or II by IMDRF. Please be sure to contact TAIYO YUDEN for further information before using the products for any equipment which may directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation, automotive powertrain control system, train control system, and ship control system, traffic signal equipment, disaster prevention equipment, medical equipment classified as Class III by IMDRF, highly public information network equipment including, without limitation, telephone exchange, and base station). Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g., aerospace equipment, aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control equipment, undersea equipment, military equipment). *Note: There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g., in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN. Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment. When our products are used even for high safety and/or reliability-required devices or circuits of general electronic equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to install a protection circuit as necessary. Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above. ■ Information contained in this catalog is intended to convey examples of typical performances and/or applications of our products and is not intended to make any warranty with respect to the intellectual property rights or any other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights. ■ Please note that the scope of warranty for our products is limited to the delivered our products themselves and TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products. Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in accordance with such agreement. ■ The contents of this catalog are applicable to our products which are purchased from our sales offices or authorized distributors (hereinafter“ TAIYO YUDEN’s official sales channel”). Please note that the contents of this catalog are not applicable to our products purchased from any seller other than TAIYO YUDEN’s official sales channel. ■ Caution for Export Some of our products listed in this catalog may require specific procedures for export according to“ U.S. Export Administration Regulations”,“ Foreign Exchange and Foreign Trade Control Law” of Japan, and other applicable regulations. Should you have any questions on this matter, please contact our sales staff. 18

WIRE-WOUND CHIP POWER INDUCTORS(BR SERIES) WIRE-WOUND CHIP POWER INDUCTORS（BR SERIES） REFLOW REFLOW ■PARTS NUMBER * Operating Temp.：-40～+105℃（Including self-generated heat） B R △ L 2 5 1 8 T 2 R 2 M △ △ △ △＝Blank space ① ② ③ ④ ⑤ ⑥ ⑦ ①Series name ④Packaging Code Series name Code Packaging BR Wire-Wound chip power inductor T Taping ②Characteristics ⑤Nominal inductance Code Characteristics Code FL （example） Nominal inductance［μH］ IN △L Low profile R20 0.2 D U HL 1R0 1.0 C △C High current 100 10 T 101 100 O ③Dimensions（L×W） ※R＝Decimal point R S Dimensions ／ Code Type（inch） （L×W）［mm］ ⑥Inductance tolerance P 1608 1608（0603） 1.6×0.8 Code Inductance tolerance O W 2012 2012（0805） 2.0×1.25 K ±10％ 2016 2016（0806） 2.0×1.6 M ±20％ E R 2518 2518（1007） 2.5×1.8 IN 3225 3225（1210） 3.2×2.5 ⑦Internal code D U C T O ■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY R Recommended Land Patterns S Surface Mounting L W ・Mounting and soldering conditions should be checked beforehand. ・Applicable soldering process to these products is reflow soldering only. Type A B C T 1608 0.55 0.70 1.00 C 2012 0.60 1.00 1.45 2016 0.60 1.00 1.80 e A B A 2518 0.60 1.50 2.00 3225 0.85 1.70 2.70 Unit：mm Standard quantity［pcs］ Type L W T e Paper tape Embossed tape 1.6±0.2 0.8±0.2 0.7 max 0.45±0.15 BR L1608 － 3000 （0.063±0.008） （0.031±0.008） （0.028 max） （0.016±0.006） 1.6±0.2 0.8±0.2 0.8±0.2 0.45±0.15 BR C1608 － 3000 （0.063±0.008） （0.031±0.008） （0.031±0.008） （0.016±0.006） 2.0±0.2 1.25±0.2 1.0 max 0.5±0.2 BR L2012 － 3000 （0.079±0.008） （0.049±0.008） （0.040 max） （0.020±0.008） 2.0±0.2 1.25±0.2 1.4 max 0.5±0.2 BR C2012 － 2000 （0.079±0.008） （0.049±0.008） （0.056 max） （0.020±0.008） 2.0±0.2 1.6±0.2 1.6±0.2 0.5±0.2 BR C2016 － 2000 （0.079±0.008） （0.063±0.008） （0.063±0.008） （0.020±0.008） 2.5±0.2 1.8±0.2 1.0 max 0.5±0.2 BRFL2518 － 3000 （0.098±0.008） （0.071±0.008） （0.040 max） （0.020±0.008） 2.5±0.2 1.8±0.2 1.2 max 0.5±0.2 BR L2518 － 3000 （0.098±0.008） （0.071±0.008） （0.048 max） （0.020±0.008） 2.5±0.2 1.8±0.2 1.5 max 0.5±0.2 BRHL2518 － 2000 （0.098±0.008） （0.071±0.008） （0.060 max） （0.020±0.008） 2.5±0.2 1.8±0.2 1.8±0.2 0.5±0.2 BR C2518 － 2000 （0.098±0.008） （0.071±0.008） （0.071±0.008） （0.020±0.008） 3.2±0.2 2.5±0.2 1.7 max 0.75±0.2 BR L3225 － 2000 （0.126±0.008） （0.098±0.008） （0.068 max） （0.03±0.008） Unit：mm（inch） i_wound_BR_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 18 77

■PARTS NUMBER ●1608（0603）TYPE Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ ［MHｚ］（min.） Idc1 Idc2 BR L1608T1R0M RoHS 1.0 ±20％ 700 0.230 510 650 1.0 BR L1608T1R5M RoHS 1.5 ±20％ 600 0.280 440 590 1.0 BR L1608T2R2M RoHS 2.2 ±20％ 400 0.400 360 500 1.0 BR L1608T3R3M RoHS 3.3 ±20％ 300 0.650 290 390 1.0 BR L1608T4R7M RoHS 4.7 ±20％ 150 1.00 240 310 1.0 BR L1608T6R8M RoHS 6.8 ±20％ 100 1.64 200 250 1.0 BR L1608T100M RoHS 10 ±20％ 45 2.00 170 220 1.0 BR L1608T150M RoHS 15 ±20％ 32 2.56 150 200 1.0 Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ ［MHｚ］（min.） Idc1 Idc2 BR C1608TR43M 6 RoHS 0.43 ±20％ 740 0.082 1,400 1,100 6.0 BR C1608TR50M 6 RoHS 0.50 ±20％ 710 0.090 1,200 1,050 6.0 BR C1608TR60M 6 RoHS 0.60 ±20％ 630 0.099 1,100 940 6.0 IN BBRR CC11660088TTRR7822MM 66 RRooHHSS 00..7822 ±±2200％％ 650600 00..114746 19,05000 871300 66..00 D BR C1608T1R0M 6 RoHS 1.0 ±20％ 550 0.188 890 680 6.0 U C Self-resonant Rated current　※）　［ｍA］ TO Parts number EHS Nomina［lμ inHdu］ctance Inductance tolerance ［MfrHeqｚu］e（nmciyn.） D［ΩC ］R（e±sis3t0a％nc）e SaturatIidocn1 current TemperatuIrdec 2rise current freqMueeanscuyr［inMgHz］ R BR C1608TR20M RoHS 0.20 ±20％ 400 0.060 1,750 980 7.96 S ／ BR C1608TR35M RoHS 0.35 ±20％ 300 0.080 1,400 810 7.96 BR C1608TR45M RoHS 0.45 ±20％ 200 0.090 1,250 800 7.96 P O BR C1608TR56M RoHS 0.56 ±20％ 170 0.095 1,150 760 7.96 W BR C1608TR77M RoHS 0.77 ±20％ 150 0.110 1,000 660 7.96 BR C1608T1R0M RoHS 1.0 ±20％ 140 0.180 850 520 7.96 E BR C1608T1R5M RoHS 1.5 ±20％ 120 0.300 700 410 7.96 R BR C1608T2R2M RoHS 2.2 ±20％ 100 0.550 550 280 7.96 IN D ●2012（0805）TYPE U Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring C Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ T ［MHｚ］（min.） Idc1 Idc2 O BR L2012TR47M 6 RoHS 0.47 ±20％ 500 0.048 1,500 1,900 6.0 R BR L2012T1R0M 6 RoHS 1.0 ±20％ 400 0.108 1,050 1,230 6.0 S BR L2012T2R2MD6 RoHS 2.2 ±20％ 250 0.184 680 950 6.0 Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ ［MHｚ］（min.） Idc1 Idc2 BR L2012TR47M RoHS 0.47 ±20％ 350 0.090 1,100 1,050 7.96 BR L2012T1R0M RoHS 1.0 ±20％ 300 0.135 850 850 7.96 BR L2012T1R5M RoHS 1.5 ±20％ 250 0.180 700 750 7.96 BR L2012T2R2M RoHS 2.2 ±20％ 200 0.300 600 550 7.96 BR L2012T3R3M RoHS 3.3 ±20％ 190 0.500 490 440 7.96 BR L2012T4R7M RoHS 4.7 ±20％ 150 0.550 340 400 7.96 BR L2012T6R8M RoHS 6.8 ±20％ 60 0.750 290 350 7.96 BR L2012T100M RoHS 10 ±20％ 30 0.850 270 330 2.52 BR L2012T150M RoHS 15 ±20％ 15 1.00 220 300 2.52 BR L2012T220M RoHS 22 ±20％ 13 1.30 190 270 2.52 BR L2012T330M RoHS 33 ±20％ 8.0 2.00 150 220 2.52 BR L2012T470M RoHS 47 ±20％ 7.0 3.50 125 160 2.52 BR L2012T680M RoHS 68 ±20％ 6.5 5.80 100 110 2.52 BR L2012T101M RoHS 100 ±20％ 6.0 7.70 85 85 0.796 Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ ［MHｚ］（min.） Idc1 Idc2 BR C2012T1R0M RoHS 1.0 ±20％ 490 0.060 1,500 1,400 1.0 BR C2012T1R5MD RoHS 1.5 ±20％ 390 0.090 1,200 1,100 1.0 BR C2012T2R2MD RoHS 2.2 ±20％ 350 0.110 1,100 1,000 1.0 BR C2012T3R3MD RoHS 3.3 ±20％ 300 0.170 800 870 1.0 BR C2012T4R7MD RoHS 4.7 ±20％ 250 0.265 700 600 1.0 ※）The saturation current value (Idc1) is the DC current value having inductance decrease down to 30%. (at 20℃) ※）The temperature rise current value (Idc2) is the DC current value having temperature increase by 40℃. (at 20℃) ※）The rated current value is following either Idc1 or Idc2, which is the lower one. i_wound_BR_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 78 18

■PARTS NUMBER ●2016（0806）TYPE Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ ［MHｚ］（min.） Idc1 Idc2 BR C2016T1R0M RoHS 1.0 ±20％ 450 0.085 1,350 1,100 0.10 BR C2016T1R5M RoHS 1.5 ±20％ 370 0.150 1,100 820 0.10 BR C2016T2R2M RoHS 2.2 ±20％ 250 0.180 910 760 0.10 BR C2016T3R3M RoHS 3.3 ±20％ 140 0.220 740 680 0.10 BR C2016T4R7M RoHS 4.7 ±20％ 78 0.270 660 610 0.10 BR C2016T6R8M RoHS 6.8 ±20％ 39 0.330 550 560 0.10 BR C2016T100[] RoHS 10 ±10％，±20％ 35 0.400 450 520 0.10 BR C2016T150[] RoHS 15 ±10％，±20％ 28 0.600 400 410 0.10 BR C2016T220[] RoHS 22 ±10％，±20％ 24 1.00 310 310 0.10 BR C2016T330[] RoHS 33 ±10％，±20％ 13 1.70 270 240 0.10 BR C2016T470[] RoHS 47 ±10％，±20％ 11 2.20 210 210 0.10 BR C2016T680[] RoHS 68 ±10％，±20％ 8 2.80 200 190 0.10 BR C2016T101[] RoHS 100 ±10％，±20％ 7 3.40 140 170 0.10 ●2518（1007）TYPE Parts number EHS Nomina［lμ inHdu］ctance Inductance tolerance Seflrfe-qreuseonncaynt D［ΩC ］R（e±sis3t0a％nc）e SaturatioRna tceudr rceunrtrent　T※em）p　er［aｍtuAre］ rise current freqMueeanscuyr［inMgHz］ IN ［MHｚ］（min.） Idc1 Idc2 D BRFL2518T1R0M RoHS 1.0 ±20％ 130 0.090 1,200 1,200 1.0 U BRFL2518T1R5M RoHS 1.5 ±20％ 100 0.110 1,100 1,000 1.0 C BRFL2518T2R2M RoHS 2.2 ±20％ 80 0.130 850 950 1.0 T O BRFL2518T3R3M RoHS 3.3 ±20％ 70 0.220 700 700 1.0 BRFL2518T4R7M RoHS 4.7 ±20％ 60 0.330 650 650 1.0 R S ／ Nominal inductance Self-resonant DC Resistance Rated current　※）　［ｍA］ Measuring P Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ O ［MHｚ］（min.） Idc1 Idc2 W BR L2518T1R0M RoHS 1.0 ±20％ 130 0.080 1,600 1,000 7.96 BR L2518T1R5M RoHS 1.5 ±20％ 100 0.100 1,200 920 7.96 E R BR L2518T2R2M RoHS 2.2 ±20％ 80 0.135 1,000 850 7.96 BR L2518T3R3M RoHS 3.3 ±20％ 70 0.300 800 580 7.96 IN BR L2518T4R7M RoHS 4.7 ±20％ 60 0.400 700 470 7.96 D U Nominal inductance Self-resonant DC Resistance Rated current　※）　［ｍA］ Measuring C Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ T ［MHｚ］（min.） Idc1 Idc2 O BRHL2518T1R0M RoHS 1.0 ±20％ 400 0.055 2,000 1,400 1.0 R BRHL2518T1R5M RoHS 1.5 ±20％ 350 0.085 1,700 1,100 1.0 S BRHL2518T2R2M RoHS 2.2 ±20％ 300 0.115 1,500 1,000 1.0 BRHL2518T3R3MD RoHS 3.3 ±20％ 200 0.165 1,200 800 1.0 BRHL2518T4R7MD RoHS 4.7 ±20％ 150 0.245 1,100 750 1.0 Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ ［MHｚ］（min.） Idc1 Idc2 BR C2518T1R0M RoHS 1.0 ±20％ 280 0.050 2,550 1,650 1.0 BR C2518T1R5M RoHS 1.5 ±20％ 230 0.080 2,100 1,300 1.0 BR C2518T2R2M RoHS 2.2 ±20％ 200 0.120 1,800 1,000 1.0 BR C2518T3R3M RoHS 3.3 ±20％ 150 0.175 1,450 860 1.0 BR C2518T4R7M RoHS 4.7 ±20％ 100 0.230 1,250 750 1.0 BR C2518T6R8M RoHS 6.8 ±20％ 45 0.280 1,050 680 1.0 BR C2518T100[] RoHS 10 ±10％，±20％ 20 0.350 890 610 1.0 BR C2518T150[] RoHS 15 ±10％，±20％ 13 0.430 760 550 1.0 BR C2518T220[] RoHS 22 ±10％，±20％ 10 0.560 640 490 1.0 BR C2518T330[] RoHS 33 ±10％，±20％ 8 0.850 560 390 1.0 BR C2518T470[] RoHS 47 ±10％，±20％ 6.5 1.45 410 300 1.0 BR C2518T680[] RoHS 68 ±10％，±20％ 5.5 2.40 340 230 1.0 BR C2518T101[] RoHS 100 ±10％，±20％ 4.5 3.60 300 190 1.0 ・ [] Please specify the inductance tolerance code. (M or K) ※）The saturation current value (Idc1) is the DC current value having inductance decrease down to 30%. (at 20℃) ※）The temperature rise current value (Idc2) is the DC current value having temperature increase by 40℃. (at 20℃) ※）The rated current value is following either Idc1 or Idc2, which is the lower one. i_wound_BR_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 18 79

■PARTS NUMBER ●3225（1210）TYPE Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±30％） Saturation current Temperature rise current frequency［MHz］ ［MHｚ］（min.） Idc1 Idc2 BR L3225TR27M RoHS 0.27 ±20％ 390 0.022 4,500 2,850 7.96 BR L3225TR36M RoHS 0.36 ±20％ 350 0.025 4,300 2,750 7.96 BR L3225TR51M RoHS 0.51 ±20％ 270 0.029 3,600 2,550 7.96 Self-resonant Rated current　※）　［ｍA］ Nominal inductance DC Resistance Measuring Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（±20％） Saturation current Temperature rise current frequency［MHz］ ［MHｚ］（min.） Idc1 Idc2 BR L3225T1R0M RoHS 1.0 ±20％ 220 0.043 2,400 2,200 0.1 BR L3225T1R5M RoHS 1.5 ±20％ 170 0.045 2,200 1,750 0.1 BR L3225T2R2M RoHS 2.2 ±20％ 150 0.065 1,850 1,600 0.1 BR L3225T3R3M RoHS 3.3 ±20％ 140 0.120 1,450 1,200 0.1 BR L3225T4R7M RoHS 4.7 ±20％ 120 0.180 1,300 1,000 0.1 BR L3225T6R8M RoHS 6.8 ±20％ 90 0.270 1,050 770 0.1 BR L3225T100[] RoHS 10 ±10％，±20％ 70 0.350 900 700 0.1 BR L3225T150[] RoHS 15 ±10％，±20％ 20 0.570 700 530 0.1 IN BBRR LL33222255TT323200[[]] RRooHHSS 3232 ±±1100％％，，±±2200％％ 193 00..864900 457500 442700 00..11 D BR L3225T470[] RoHS 47 ±10％，±20％ 7 1.00 420 390 0.1 U BR L3225T680[] RoHS 68 ±10％，±20％ 6 1.40 330 300 0.1 C BR L3225T101[] RoHS 100 ±10％，±20％ 5 2.50 270 250 0.1 T ・ [] Please specify the inductance tolerance code. (M or K) O R ※）The saturation current value (Idc1) is the DC current value having inductance decrease down to 30%. (at 20℃) S ／ ※）The temperature rise current value (Idc2) is the DC current value having temperature increase by 40℃. (at 20℃) ※）The rated current value is following either Idc1 or Idc2, which is the lower one. P O W E R IN D U C T O R S i_wound_BR_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 80 18

WIRE-WOUND CHIP POWER INDUCTORS（BR SERIES） ■PACKAGING ①Minimum Quantity Standard Quantity [pcs] Type Paper Tape Embossed Tape BR C1608 － 3,000 BR L1608 － 3,000 BR L2012 － 3,000 BR C2012 － 2,000 BR C2016 － 2,000 BR C2518 － 2,000 BRHL2518 － 2,000 BR L2518 － 3,000 BRFL2518 － 3,000 BR L3225 － 2,000 ②Tape Material ●Embossed tape Top tape Sprocket hole Base tape Chip cavity Chip Filled Chip ③Taping dimensions ●Embossed Tape 8mm wide (0.315 inches wide) φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） A B 3.5±0.05(0.138±0.002) 8.0±0.20.315±0.008) ( F 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_BR_pack_e-E05R01

Chip cavity Insertion pitch Tape thickness Type A B F T K 1.1±0.1 1.9±0.1 4.0±0.1 0.2±0.05 0.9 max BR L1608 (0.043±0.004) (0.075±0.004) (0.157±0.004) (0.008±0.002) (0.035 max) 1.1±0.1 1.9±0.1 4.0±0.1 0.25±0.05 1.2 max BR C1608 (0.043±0.004) (0.075±0.004) (0.157±0.004) (0.010±0.002) (0.047 max) 1.45±0.1 2.2±0.1 4.0±0.1 0.25±0.05 1.2 max BR L2012 (0.057±0.004) (0.087±0.004) (0.157±0.004) (0.010±0.002) (0.047 max) 1.45±0.1 2.37±0.1 4.0±0.1 0.25±0.05 1.59 max BR C2012 (0.057±0.004) (0.093±0.004) (0.157±0.004) (0.010±0.002) (0.063 max) 1.75±0.1 2.1±0.1 4.0±0.1 0.3±0.05 1.9 max BR C2016 (0.069±0.004) (0.083±0.004) (0.157±0.004) (0.012±0.002) (0.075 max) 2.3±0.1 2.8±0.1 4.0±0.1 0.25±0.05 1.3 max BRFL2518 (0.091±0.004) (0.110±0.004) (0.157±0.004) (0.010±0.002) (0.051 max) 2.3±0.1 2.8±0.1 4.0±0.1 0.3±0.05 1.45 max BR L2518 (0.091±0.004) (0.110±0.004) (0.157±0.004) (0.012±0.002) (0.057 max) 2.1±0.1 2.8±0.1 4.0±0.1 0.3±0.05 1.7 max BRHL2518 (0.083±0.004) (0.110±0.004) (0.157±0.004) (0.012±0.002) (0.067 max) 2.15±0.1 2.7±0.1 4.0±0.1 0.3±0.05 2.2 max BR C2518 (0.085±0.004) (0.106±0.004) (0.157±0.004) (0.012±0.002) (0.087 max) 2.8±0.1 3.5±0.1 4.0±0.1 0.25±0.05 1.9 max BR L3225 (0.110±0.004) (0.138±0.004) (0.157±0.004) (0.010±0.002) (0.075 max) Unit：mm（inch） ④Leader and Blank portion ⑤Reel size ⑥Top Tape Strength The top tape requires a peel-off force of 0.2 to 0.7N in the direction of the arrow as illustrated below. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_BR_pack_e-E05R01

WIRE-WOUND CHIP POWER INDUCTORS（BR SERIES） ■RELIABILITY DATA 1. Operating Temperature Range Specified Value BR series －40～＋105℃ Test Methods and Including self-generated heat Remarks 2. Storage Temperature Range（after soldering） Specified Value BR series －40～＋85℃ Test Methods and Please refer the term of "7.Storage conditions" in Precautions. Remarks 3. Rated current Specified Value BR series Within the specified tolerance 4. Inductance Specified Value BR series Within the specified tolerance Test Methods and Measuring equipment : LCR Meter （HP 4285A or equivalent） Remarks Measuring frequency : Specified frequency 5. DC Resistance Specified Value BR series Within the specified tolerance Test Methods and Measuring equipment : DC ohmmeter （HIOKI 3227 or equivalent） Remarks 6. Self resonance frequency Specified Value BR series Within the specified tolerance Test Methods and Measuring equipment : Impedance analyzer/material analyzer Remarks （HP4291A or equivalent HP4191A, 4192A or equivalent） 7. Temperature characteristic Specified Value BR series Inductance change : Within ±15% Test Methods and Based on the inductance at 20℃ and Measured at the ambient of －40℃～＋85℃. Remarks 8. Resistance to the bendability Specified Value BR series No damage. Test Methods and The given sample is soldered on the board and then the back side of the board is pushed until it bends 2mm like the figure. Remarks Dimension of the board : 100×40×1.0mm (0.8mm thickness for 1608(0603) inductors) Material of the board : Glass epoxy-resin Thickness of soldering paste : 0.12mm ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_BR_reli_e-E05R01

9. Body strength Specified Value BR series No damage. Test Methods and 2012～ Remarks Applied orce 10N Duration : 10sec. 1608 size Applied force : 5N Duration : 10sec. 10. Adhesion of terminal electrodes Specified Value BR series Not to removed from the board. Test Methods and The given sample is soldered to the board and then it is kept for 5sec with 10N stress (5N for 1608(0603) inductors) like the figure. Remarks 11. Resistance to vibration Inductance change : Within ±10% Specified Value BR series No significant abnormality in appearance. Test Methods and The given sample is soldered to the board and then it is tested depending on the conditions of the following table. Remarks Vibration Frequency 10～55Hz Total Amplitude 1.5mm (May not exceed acceleration 196m/s2) Sweeping Method 10Hz to 55Hz to 10Hz for 1min. X Time Y For 2 hours on each X, Y, and Z axis. Z Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 12. Solderability Specified Value BR series At least 90% area of the electrodes is covered by new solder. Test Methods and Test Method and Remarks】 Remarks The given sample is dipped into the flux and then it is tested depending on the conditions of the following table. Flux : Methanol solution containing rosin 25%. Solder Temperature 245±5℃ Time 5±0.5 sec. 13. Resistance to soldering heat Inductance change : Within ±10% Specified Value BR series No significant abnormality in appearance. Test Methods and 3 times reflow having the temperature profile of 5sec of 260＋0/－5 ℃ and 40sec of more than 230℃. Remarks Test board thickness : 1.0mm Test board material : Glass epoxy-resin Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 14. Thermal shock Inductance change : Within ±10% Specified Value BR series No significant abnormality in appearance. Test Methods and The given sample is soldered to the board and then its Inductance is measured after 100cycles of the following conditions. Remarks Conditions of 1 cycle Step Temperature (℃) Duration (min) 1 －40±3 30±3 2 Room temperature Within 3 3 ＋85±2 30±3 4 Room temperature Within 3 Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_BR_reli_e-E05R01

15. Damp heat Inductance change : Within ±10% Specified Value BR series No significant abnormality in appearance. Test Methods and The given sample is soldered to the board and then it is kept at the following conditions. Remarks Temperature 60±2℃ Humidity 90～95%RH Time 1000 hours. Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 16. Loading under damp heat Inductance change : Within ±10% Specified Value BR series No significant abnormality in appearance. Test Methods and The given sample is soldered to the board and then it is kept at the following conditions. Remarks Temperature 60±2℃ Humidity 90～95％RH Applied current Rated current Time 1000hours. Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 17. Low temperature life test Inductance change : Within ±10% Specified Value BR series No significant abnormality in appearance. Test Methods and The given sample is soldered to the board and then it is kept at the following conditions. Remarks Temperature －40±2℃ Duration 1000hours Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 18. High temperature life test Inductance change : Within ±10% Specified Value BR series No significant abnormality in appearance. Test Methods and The given sample is soldered to the board and then it is kept at the following conditions. Remarks Temperature 85±2℃ Duration 1000hours Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 19. Standard conditions Standard test condition : Unless otherwise specified, temperature is 20±15℃ and 65±20％of relative humidity. When there is any question concerning measurement result: In order to provide Specified Value BR series correlation data, the test shall be condition of 20±2℃ of temperature, 65±5% relative humidity. Inductance is in accordance with our measured value. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_BR_reli_e-E05R01

WIRE-WOUND CHIP POWER INDUCTORS（BR SERIES） ■PRECAUTIONS 1. Circuit Design ◆Operating Ambient The products are premised on the usage for the general equipments like the office supply equipment, the telecommunications systems, the measuring equipment, the household equipment and so on. Precautions Please ask to TAIYO YUDEN's sales person in advance, if you need to apply them to the equipments or the systems which might have any influences for the human body, the property, like the traffic systems, the safety equipment, the aerospace systems, the nuclear control systems, the medical equipment and soon. 2. PCB Design ◆Land pattern design Precautions 1. Please refer to a recommended land pattern. ◆Land pattern design Technical Surface Mounting considerations 1. The conditions of the picking and placing should be checked in advance. 2. The products are only for reflow soldering. 3. Considerations for automatic placement ◆Adjustment of mounting machine Precautions 1. Excessive physical impact should not be imposed on the products for picking and placing onto the PC boards. 2. Mounting and soldering conditions should be checked in advance. Technical ◆Adjustment of mounting machine considerations The products might be broken if too much stress is given for the picking and placing. 4. Soldering ◆Reflow soldering 1. Please apply our recommended soldering conditions on the specification as much as possible. 2. The products are only for reflow soldering. 3. Please do not give any stress to a product until it returns in room temperature after reflow soldering. Precautions ◆Recommended conditions for using a soldering iron. （Excluding 1608 type） Touch a soldering iron to the land pattern not to the product directly. The temperature of a soldering iron is less than 350degC. The soldering is for 3 seconds or less. ◆Reflow soldering 1. The product might break or might make the tombstoning, if the soldering conditions are too far from our recommended conditions. Technical considerations 5. Cleaning ◆Cleaning conditions Precautions 1. Please don't wash by the ultra-sonic waves. Technical ◆Cleaning conditions considerations 1. Washing by the ultra-sonic waves might break the product. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_BR_prec_e-E06R01

6. Handling ◆Handling 1. Keep the product away from any magnets. ◆Cutting the PC boards 1. Please don't give any stress of the bending or the twisting for the cutting process of PC boards. 2. Please don't give any shock and stress to the products in transportation. ◆Mechanical considerations Precautions 1. Please don't give too much shock to the product. 2. Please don't give any shock and stress to the products in transportation. ◆The stress for picking and placing 1. Please don't give any shock into an exposed ferrite core. ◆Packing 1. Please don't pile the packing boxes up as much as possible. ◆Handling 1. There is a case that a characteristic varies with magnetic influence. ◆Cutting the PC boards 1. Please don't give the bending stress or the twisting stress to the products because they might break in such cases. ◆Mechanical considerations Technical 1. The mechanical shock might break the products. considerations 2. The products might break depending on the handling in transportation. ◆Pick-up pressure 1. The electrical characteristics of the products might be shifted by too much physical shock and stress. ◆Packing 1. The products and the tape might break, if the packing boxes are piled up. 7. Storage conditions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. ・ Recommended conditions Ambient temperature : 0～40℃ Precautions Humidity : Below 70% RH ・ The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, product should be used within 6 months from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. Technical ◆Storage considerations 1. The ambient of high temperature or high humidity might accelerate to make the solderability and the tape worse. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_BR_prec_e-E06R01

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: T aiyo Yuden: BRC1608T1R0M6 BRC1608TR43M6 BRC1608TR50M6 BRC1608TR60M6 BRC1608TR72M6 BRC1608TR82M6 BRC1608T1R0M BRC1608T1R5M BRC1608T2R2M BRC1608TR20M BRC1608TR35M BRC1608TR45M BRC1608TR56M BRC1608TR77M BRC2012T1R0M BRC2012T1R5MD BRC2012T2R2MD BRC2012T3R3MD BRC2012T4R7MD BRC2016T100K BRC2016T100M BRC2016T101K BRC2016T101M BRC2016T150K BRC2016T150M BRC2016T1R0M BRC2016T1R5M BRC2016T220K BRC2016T220M BRC2016T2R2M BRC2016T330K BRC2016T330M BRC2016T3R3M BRC2016T470K BRC2016T470M BRC2016T4R7M BRC2016T680K BRC2016T680M BRC2016T6R8M BRC2518T100K BRC2518T100M BRC2518T101K BRC2518T101M BRC2518T150K BRC2518T150M BRC2518T1R0M BRC2518T1R5M BRC2518T220K BRC2518T220M BRC2518T2R2M BRC2518T330K BRC2518T330M BRC2518T3R3M BRC2518T470K BRC2518T470M BRC2518T4R7M BRC2518T680K BRC2518T680M BRC2518T6R8M BRFL2518T1R0M BRFL2518T1R5M BRFL2518T2R2M BRFL2518T3R3M BRFL2518T4R7M BRHL2518T1R0M BRHL2518T1R5M BRHL2518T2R2M BRHL2518T3R3MD BRHL2518T4R7MD BRL1608T100M BRL1608T150M BRL1608T1R0M BRL1608T1R5M BRL1608T2R2M BRL1608T3R3M BRL1608T4R7M BRL1608T6R8M BRL2012T100M BRL2012T101M BRL2012T150M BRL2012T1R0M BRL2012T1R5M BRL2012T220M BRL2012T2R2M BRL2012T330M BRL2012T3R3M BRL2012T470M BRL2012T4R7M BRL2012T680M BRL2012T6R8M BRL2012TR47M BRL2515T1R0M BRL2515T1R5M BRL2515T2R2M BRL2515T3R3MD BRL2515T4R7MD BRL2518T1R0M BRL2518T1R5M BRL2518T2R2M BRL2518T3R3M