Datasheet Serial EEPROM series Standard EEPROM 2 I C BUS EEPROM (2-Wire) BR24Sxxx-W (8K 16K 32K 64K 128K 256K) ●General Description BR24Sxxx-W is a serial EEPROM of I2C BUS interface method ●Features ●Packages W(Typ.) x D(Typ.) x H(Max.) (cid:132) Completely conforming to the world standard I2C BUS. All controls available by 2 ports of serial clock (SCL) and serial data (SDA) (cid:132) Other devices than EEPROM can be connected to the same port, saving microcontroller port SOP8 TSSOP-B8 (cid:132) 1.7V to 5.5V single power source action most suitable 5 .00mm x 6.20mm x 1.71mm 3.00mm x 6.40mm x 1.20mm for battery use (cid:132) FAST MODE 400kHz at 1.7V to 5.5V (cid:132) Page write mode useful for initial value write at factory shipment (cid:132) Highly reliable connection by Au pad and Au wire (cid:132) Auto erase and auto end function at data rewrite SOP-J8 TSSOP-B8J (cid:132) Low current consumption 4.90mm x 6.00mm x 1.65mm 3.00mm x 4.90mm x 1.10mm (cid:190) At write operation (5V) : 0.5mA (Typ.) (cid:190) At read operation (5V) : 0.2mA (Typ.) (cid:190) At standby operation (5V) : 0.1μA (Typ.) (cid:132) Write mistake prevention function (cid:190) Write (write protect) function added SSOP-B8 MSOP8 (cid:190) Write mistake prevention function at low voltage 3.00mm x 6.40mm x 1.35mm 2.90mm x 4.00mm x 0.90mm (cid:132) Data rewrite up to 1,000,000 times (cid:132) Data kept for 40 years (cid:132) Noise filter built in SCL / SDA terminal (cid:132) Shipment data all address FFh VSON008X2030 2.00mm x 3.00mm x 0.60mm ●Page write Number of pages 16Byte 32Byte 64Byte BR24S08-W BR24S32-W BR24S128-W Product number BR24S16-W BR24S64-W BR24S256-W ●BR24Sxxx-W Bit Power source VSON008 Capacity Type SOP8 SOP-J8 SSOP-B8 TSSOP-B8 MSOP8 TSSOP-B8J format voltage X2030 8Kbit 1K×8 BR24S08-W 1.7V to 5.5V ● ● ● ● ● ● ● 16Kbit 2K×8 BR24S16-W 1.7V to 5.5V ● ● ● ● ● ● ● 32Kbit 4K×8 BR24S32-W 1.7V to 5.5V ● ● ● ● ● ● ● 64Kbit 8K×8 BR24S64-W 1.7V to 5.5V ● ● ● ● ● ● 128Kbit 16K×8 BR24S128-W 1.7V to 5.5V ● ● ● ● 256Kbit 32K×8 BR24S256-W 1.7V to 5.5V ● ● ○Product structure：Silicon monolithic integrated circuit ○This product is not designed protection against radioactive rays www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 1/33 TSZ22111･14･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Ratings Unit Remarks Supply Voltage V -0.3 to +6.5 V CC 450 (SOP8) When using at Ta=25℃ or higher 4.5mW to be reduced per 1℃. 450 (SOP-J8) When using at Ta=25℃ or higher 4.5mW to be reduced per 1℃. 300 (SSOP-B8) When using at Ta=25℃ or higher 3.0mW to be reduced per 1℃. Power Dissipation Pd 330 (TSSOP-B8) mW When using at Ta=25℃ or higher 3.3mW to be reduced per 1℃. 310 (TSSOP-B8J) When using at Ta=25℃ or higher 3.1mW to be reduced per 1℃. 310 (MSOP8) When using at Ta=25℃ or higher 3.1mW to be reduced per 1℃. 300 (VSON008X2030) When using at Ta=25℃ or higher 3.0mW to be reduced per 1℃. Storage Temperature Tstg －65 to +125 ℃ Operating Temperature Topr －40 to +85 ℃ Terminal Voltage ‐ -0.3 to Vcc+1.0 V ●Memory cell characteristics (Ta=25℃, Vcc=1.7V to 5.5V) Limits Parameter Unit Min. Typ. Max. Number of data rewrite times *1 1,000,000 - - Times Data hold years *1 40 - - Years *1 Not 100% TESTED ●Recommended Operating Ratings Parameter Symbol Ratings Unit Power source voltage Vcc 1.7 to 5.5 V Input voltage V 0 to Vcc IN ●Electrical Characteristics (Unless otherwise specified, Ta=-40℃ to +85℃, VCC=1.7V to 5.5V) Limits Parameter Symbol Unit Condition Min Typ. Max. "H" Input Voltage1 VIH1 0.7Vcc - Vcc+1.0 V "L" Input Voltage1 VIL1 -0.3 - 0.3Vcc V "L" Output Voltage1 VOL1 - - 0.4 V IOL=3.0mA , 2.5V≦Vcc≦5.5V (SDA) "L" Output Voltage2 VOL2 - - 0.2 V IOL=0.7mA , 1.7V≦Vcc≦2.5V (SDA) Input Leakage Current ILI -1 - 1 μA VIN=0 to Vcc Output Leakage Current ILO -1 - 1 μA VOUT=0 to Vcc (SDA) Vcc=5.5V , fSCL =400kHz, tWR=5ms - - 2.0 Byte Write, Page Write BR24S08/16/32/64-W ICC1 mA Current consumption Vcc=5.5V , fSCL =400kHz, tWR=5ms - - 2.5 at action Byte Write, Page Write BR24S128/256-W Vcc=5.5V , fSCL =400kHz ICC2 - - 0.5 mA Random read, Current read, Sequential read Vcc=5.5V , SDA・SCL=Vcc Standby Current ISB - - 2.0 μA A0, A1, A2=GND, WP=GND www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 2/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Action timing characteristics (Unless otherwise specified, Ta=-40℃ to +85℃, VCC=1.7V to 5.5V) Limits Parameter Symbol Unit Min. Typ. Max. SCL Frequency fSCL - - 400 kHz Data clock "High" time tHIGH 0.6 - - μs Data clock "Low" time tLOW 1.2 - - μs SDA, SCL rise time *1 tR - - 0.3 *2 μs SDA, SCL fall time *1 tF - - 0.3 μs Start condition hold time tHD:STA 0.6 - - μs Start condition setup time tSU:STA 0.6 - - μs Input data hold time tHD:DAT 0 - - ns Input data setup time tSU:DAT 100 - - ns Output data delay time tPD 0.1 - 0.9 μs Output data hold time tDH 0.1 - - μs Stop condition data setup time tSU:STO 0.6 - - μs Bus release time before transfer start tBUF 1.2 - - μs Internal write cycle time tWR - - 5 ms Noise removal valid period (SDA,SCL terminal) tI - - 0.1 μs WP hold time tHD:WP 0 - - ns WP setup time tSU:WP 0.1 - - μs WP valid time tHIGH:WP 1.0 - - μs *1 : Not 100% TESTED *2 : BR24S16/64-W : 1.0μs. ●Sync data input / output timing tR tF tHIGH SCL SCL tHD:STA tSU:DAT tLOW tHD:DAT tSU:STA tHD:STA tSU:STO SDA (I(n入pu力t)) SDA tBUF tPD tDH SDA START BIT STOP BIT (O(u出tp力u)t) ○Input read at the rise edge of SCL ○Data output in sync with the fall of SCL Figure 1-(a) Sync data input / output timing Figure 1-(b) Start - stop bit timing SCL SCL DATA(1) DATA(n) SDA D0 ACK WRITE DATA(n) tWR SDA D1 D0 ACK ACK STOP START ｔWR CONDITION CONDITION WP Sスtoトpッ cプoコnンdiデtioィnシ ョン tSU：WP ｔHD：WP Figure 1-(c) Write cycle timing Figure 1-(d) WP timing at write execution SCL DATA(1) DATA(n) SDA D1 D0 ACK ACK tHIGH:WP tWtWRR WP ○At write execution, in the area from the D0 taken clock rise of the first DATA(1), to tWR, set WP= 'LOW'. ○By setting WP "HIGH" in the area, write can be cancelled. When it is set WP = 'HIGH' during tWR, write is forcibly ended, and data of address under access is not guaranteed, therefore write it once again. Figure 1-(e) WP timing at write cancel www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 3/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Block Diagram *2 A 0 1 8K bitto256Kbit EEPROM array 8 Vcc 111*0121bbb iii ttt 8bit 13bit 14bit 15bit *2 A 1 2 Adedcdod dree sr s *1 1111 0123bbbbiiiitttt aSdladvree s-s w roergdis ter Dreagtias ter 7 WP 1145bbiitt START STOP *2 A 2 3 6 SCL Control circuit ACK GND 4 Hgeignhe rvaotlitnagg ec i r cuit Pvoolwtaegre s doeutreccet ion 5 SDA ＊1 10bit: BR24S08-W ＊2 A0, A1=Don't use: BR24S08-W 11bit: BR24S16-W A0, A1, A2=Don't use: BR24S16-W 12bit: BR24S32-W 13bit: BR24S64-W 14bit: BR24S128-W 15bit: BR24S256-W ●Pin Configuration (TOP VIEW) A0 1 8 Vcc A1 2 BR24S08-W 7 WP BR24S16-W BR24S32-W A2 3 BR24S64-W 6 SCL BR24S128-W BR24S256-W GND 4 5 SDA ●Pin Descriptions Terminal Input/ Function name Output BR24S08-W BR24S16-W BR24S32/64/128/256-W A0 Input Don't use Don't use Slave address setting A1 Input Don't use Don't use Slave address setting A2 Input Slave address setting Don't use Slave address setting GND - Reference voltage of all input / output, 0V. Slave and word address, SDA Input / Output Serial data input serial data output SCL Input Serial clock input WP Input Write protect terminal Vcc - Connect the power source. www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 4/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Typical Performance Curves (The following values are Typ. ones.) Figure 3. "L" Input Voltage VIL Figure 2. "H" Input Voltage VIH (A0, A1, A2, SCL, SDA, WP) (A0, A1, A2, SCL, SDA, WP) Figure 4. "L" Output Voltage Figure 5."L" Output Voltage VOL-IOL VOL-IOL1(Vcc=1.7V) (Vcc=2.5V) www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 5/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Typical Performance Curves‐Continued A] [uO IL Figure 6. Input Leak Current ILI Figure 7.Output Leak Current ILO (SDA) (A0, A1, A2, SCL, WP) Figure 8. Current consumption at WRITE operation Figure 9.Current consumption at WRITE operation ICC1 ICC1 (fscl=400kHz BR24S16/32/64-W) (fscl=400kHz BR24S128/256-W) www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 6/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Typical Performance Curves‐Continued Figure 10. Current consumption at READ operation Figure 11.Standby operation ISB ICC2 (fscl=400kHz) Figure 12. SCL frequency fSCL Figure 13.Data clock High Period tHIGH www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 7/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Typical Performance Curves‐Continued Figure 14. Data clock LOW Period tLOW Figure 15. Start Condition Hold Time tHD:STA Figure 16. Start Condition Setup Time tSU:STA Figure 17.InputData Hold Time tHD:DAT(HIGH) www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 8/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Typical Performance Curves‐Continued Figure 18. Input Data Hold Time tHD:DAT(LOW) Figure 19.Input Data Setup Time tSU:DAT(HIGH) Figure 20. Input Data Setup Time tSU:DAT(LOW) Figure 21.“L” Data output delay time tPD0 www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 9/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Typical Performance Curves‐Continued Figure 22. “H” Data output delay time tPD1 Figure 23.BUS open time before transmission tBUF Figure 24. Internal writing cycle time tWR Figure 25.Noise reduction affectiontime tl(SCL H) www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 10/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Typical Performance Curves‐Continued Figure 26. Noise reduction effective time tl(SCL L) Figure 27.Noise reduction effective time tl(SDA H) Figure 28. Noise reduction effective time tI(SDA L) Figure 29. WP setup time tSU:WP www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 11/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Typical Performance Curves‐Continued E V TI C E F E P W Figure 30. WP effective time tHIGH:WP www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 12/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●I2C BUS Communication ○I2C BUS data communication I2C BUS data communication starts by start condition input, and ends by stop condition input. Data is always 8bit long, and acknowledge is always required after each byte. I2C BUS carries out data transmission with plural devices connected by 2 communication lines of serial data (SDA) and serial clock (SCL). Among devices, there are “master” that generates clock and control communication start and end, and “slave” that is controlled by addresses peculiar to devices. EEPROM becomes “slave”. And the device that outputs data to bus during data communication is called “transmitter”, and the device that receives data is called “receiver”. SDA 1-7 8 9 1-7 8 9 1-7 8 9 SCL S P START ADDRESS R/W ACK DATA ACK DATA ACK STOP condition condition Figure 31. Data transfer timing ○Start condition (start bit recognition) ・Before executing each command, start condition (start bit) where SDA goes from 'HIGH' down to 'LOW' when SCL is 'HIGH' is necessary. ・This IC always detects whether SDA and SCL are in start condition (start bit) or not, therefore, unless this condition is satisfied, any command is executed. ○Stop condition (stop bit recognition) ・Each command can be ended by SDA rising from 'LOW' to 'HIGH' when stop condition (stop bit), namely, SCL is 'HIGH' ○Acknowledge (ACK) signal ・This acknowledge (ACK) signal is a software rule to show whether data transfer has been made normally or not. In master and slave, the device (μ-COM at slave address input of write command, read command, and this IC at data output of read command) at the transmitter (sending) side releases the bus after output of 8bit data. ・The device (this IC at slave address input of write command, read command, and μ-COM at data output of read command) at the receiver (receiving) side sets SDA 'LOW' during 9 clock cycles, and outputs acknowledge signal (ACK signal) showing that it has received the 8bit data. ・This IC, after recognizing start condition and slave address (8bit), outputs acknowledge signal (ACK signal) 'LOW'. ・Each write action outputs acknowledge signal) (ACK signal) 'LOW', at receiving 8bit data (word address and write data). ・Each read action outputs 8bit data (read data), and detects acknowledge signal (ACK signal) 'LOW'. ・When acknowledge signal (ACK signal) is detected, and stop condition is not sent from the master (μ-COM) side, this IC continues data output. When acknowledge signal (ACK signal) is not detected, this IC stops data transfer, and recognizes stop condition (stop bit), and ends read action. And this IC gets in standby status. ○Device addressing ・Output slave address after start condition from master. ・The significant 4 bits of slave address are used for recognizing a device type. The device code of this IC is fixed to '1010'. ・Next slave addresses (A2 A1 A0 --- device address) are for selecting devices, and plural ones can be used on a same bus according to the number of device addresses. ・The most insignificant bit (R/W --- READ/WRITE) of slave address is used for designating write or read action, and is as shown below. Setting R/W to 0 --- write (setting 0 to word address setting of random read) Setting R/W to 1 --- read A0 1 8 Vcc Maximum number of Type Slave address connected buses BR24S08-W 1 0 1 0 A2 P1 P0 R/W― 2 A1 2 BBRR2244SS0186--WW 7 WP BR24S32-W BR24S16-W 1 0 1 0 P2 P1 P0 R/W― 1 A2 3 BBRR2244SS6142-8W-W 6 SCL BR24S32-W, BR24S64-W 1 0 1 0 A2 A1 A0 R/W― 8 B R24S256-W BR24S128-W, BR24S256-W GND 4 5 SDA P0 to P2 are page select bits. Note) Up to 2 units of BR24S08-W, up to 1 units of BR24S16-W, and up to 8 units of BR24S32/64/128/256-W can be connected. Device address is set by 'H' and 'L' of each pin of A0, A1, and A2. www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 13/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Write Command ○Write cycle ・Arbitrary data is written to EEPROM. When to write only 1 byte, byte write normally used, and when to write continuous data of 2 bytes or more, simultaneous write is possible by page write cycle. The maximum number of write bytes is specified per device of each capacity. Up to 64 arbitrary bytes can be written. (In the case of BR24S128/256-W) S W T R S RA SLAVE TI WORD DATA OT T ADDRESS E ADDRESS P SDA LINE 1 0 1 0 A2 A1 A0 W7A W0A D7 D0 R A A A Note) / C C C W K K K Figure 32. Byte write cycle (BR24S08/16-W) S W T R S A I T R SLAVE T 1st WORD 2nd WORD DATA O T ADDRESS E ADDRESS ADDRESS P *1 As for WA12, BR24S32-W becomes Don't care. SDA As for WA13, BR24S32/64-W becomes Don't care. LINE 1 0 1 0 A2 A1 A0 ＊ WAWA WAW A WA D7 D0 As for WA14, BR24S32/64/128-W becomes Don't care. 1413 12 11 0 Note) R/ CA *1 CA CA CA W K K K K Figure 33. Byte write cycle (BR24S32/64/128/256-W) S W T R S A I T R SLAVE T WORD *2 O T ADDRESS E ADDRESS(n) DATA(n) DATA(n+15) P SDA LINE 1 0 1 0 A2A 1A 0 W7A W0A D7 D0 D0 R A A A A Note注) ) / C *1 C C C W K K K K Figure 34. Page write cycle (BR24S08/16-W) S W T R S RAT ADSDLARVEES S ETI A1DsDt RWEOSRSD(n ) A2DnDdR WEOSRS(Dn ) DATA(n) DATA(n+3*12) OPT * 1 AAss ffoorr WWAA1123,, BBRR2244SS3322-/W64 -bWec boemceosm Deso nD'to cna'tr ec.a re. SLIDNAE 1 0 1 0 A2A 1A 0 ＊ WA WAW AWA WA D7 D0 D0 As for WA14, BR24S32/64/128-W becomes Don't care. 14 13 12 11 0 Note) R/ CA *1 CA CA CA CA *2 As for BR24S128/256-W becomes (n+63). W K K K K K Figure 35. Page write cycle (BR24S32/64/128/256-W) ・Data is written to the address designated by word address (n-th address). ・By issuing stop bit after 8bit data input, write to memory cell inside starts. ・When internal write is started, command is not accepted for tWR (5ms at maximum). ・By page write cycle, the following can be written in bulk: Up to 16 bytes (BR24S08-W, BR24S16-W) : Up to 32 bytes (BR24S32-W, BR24S64-W) : Up to 64 bytes (BR24S128-W, BR24S256-W) And when data of the maximum bytes or higher is sent, data from the first byte is overwritten. (Refer to "Internal address increment in Page 15.) ・As for page write command of BR24S08-W and, BR24S16-W, after page select bit(PS) of slave address is designated arbitrarily, by continuing data input of 2 bytes or more, the address of insignificant 4 bits is incremented internally, and data up to 16 bytes can be written. ・As for page write cycle of BR24S32-W and BR24S64-W , after the significant 7 bits (in the case of BR24S32-W) of word address, or the significant 8 bits (in the case of BR24S64-W) of word address are designated arbitrarily, by continuing data input of 2 bytes or more, the address of insignificant 5 bits is incremented internally, and data up to 32 bytes can be written. ・As for page write cycle of BR24S128-W and BR24S256-W, after the significant 9 bit (in the case of BR24S128-W) of word address, or the significant 10bit (in the case of BR24S256-W) of word address are designated arbitrarily, by continuing data input of 64 bytes or more. Note) *1 *2 *3 *1 In BR24S16-W, A2 becomes P2 1 0 1 0 A2A 1A 0 *2 In BR24S08/16-W, A1 becomes P1 *3 In BR24S08/16-W, A0 becomes P0 Figure 36. Difference of slave address each type www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 14/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ○Notes on write cycle continuous input At STOP (stop bit) write starts. S W S T R S T A I T A RT ADSDLARVEES S TE ADDWROERSDS（ ｎ） DATA(n) DATA(n+15) OP RT SDA LINE 1 0 1 0 P2 P1 P0 WA W0A D7 D0 D0 1 0 1 0 7 R A A A A Next command note) / C C C C W K K K K tWR(maximum：5ms) Command is not accepted for this Figure 37. Page write cycle(BR24S08/16-W) period. At STOP (stop bit) write starts. ST WR S ST SLIDNAE RAT ADSDLARVEES S ETI A1DsDt RWEOSRSD(n ) A2DnDdR WEOSRS(Dn ) DATA(n) DATA(n+3*12) OPT RAT * 1 AAss ffoorr WWAA1123,, BBRR2244SS3322-/W64 -bWec boemceosm Deso nD'to cna'tr ec.a re. As for WA14, BR24S32/64/128-W becomes Don't care. 1 0 1 0 A2A 1A 0 ＊ W14A W13A W1 2A W11A W0A D7 D0 D0 1 0 1 0 note) R/ CA *1 CA CA CA CA Next command *2 As for BR24S128/256-W becomes (n+63). W K K K K K tWR(maximum : 5ms) Command is not accepted for this period. Figure 38. Page write cycle(BR24S32/64/128/256-W) ○Notes on page write cycle List of numbers of page write Number of pages 16Byte 32Byte 64Byte BR24S128-W BR24S08-W BR24S32-W Product number BR24S256-W BR24S16-W BR24S64-W The above numbers are maximum bytes for respective types. Any bytes below these can be written. In the case of BR24S256-W, 1 page = 64bytes, but the page write cycle write time is 5ms at maximum for 64byte bulk write. It does not stand 5ms at maximum × 64byte = 320ms(Max.). ○Internal address increment Page write mode (in the case of BR24S16-W) WA7 ----- WA4 WA3 WA2 WA1 WA0 0 ----- 0 0 0 0 0 Increment 0 ----- 0 0 0 0 1 0 ----- 0 0 0 1 0 --------- --------- 0 ----- 0 1 1 1 0 0Eh 0 ----- 0 1 1 1 1 0 ----- 0 0 0 0 0 Significant bit is fixed. No digit up For example, when it is started from address 0Eh, therefore, increment is made as below, 0Eh→0Fh→00h→01h･･･, which please note. * 0Eh･･･16 in hexadecimal, therefore, 00001110 becomes a binary number. ○Write protect (WP) terminal ・Write protect (WP) function When WP terminal is set Vcc (H level), data rewrite of all address is prohibited. When it is set GND (L level), data rewrite of all address is enabled. Be sure to connect this terminal to Vcc or GND, or control it to H level or L level. Do not use it open. At extremely low voltage at power ON/OFF, by setting the WP terminal 'H', mistake write can be prevented. During tWR, set the WP terminal always to 'L'. If it is set 'H', write is forcibly terminated. www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 15/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Read Command ○Read cycle Data of EEPROM is read. In read cycle, there are random read cycle and current read cycle. Random read cycle is a command to read data by designating address, and is used generally. Current read cycle is a command to read data of internal address register without designating address, and is used when to verify just after write cycle. In both the read cycles, sequential read cycle is available, and the next address data can be read in succession. ST WR ST R S RA SLAVE TI WORD RA SLAVE EA OT It is necessary to input 'H' T ADDRESS E ADDRESS(n) T ADDRESS D DATA(n) P to the last ACK. SLIDNAE 1 0 1 0 A2A 1A 0 WA WA 1 0 1 0 A2A1A 0 D7 D0 7 0 Note) R/ CA CA R/ CA CA W K K WK K Figure 39. Random read cycle (BR24S08/16-W) S W S T R T R S ART ADSDLARVEES S TEI AD1DstR WESOSR（Dｎ ） AD2nDdR WESOSR（Dｎ ） ART ADSLDARVEESS DAE DATA(n) OPT *1 As for WA12, BR24S32-W become Don't care. SLIDNAE 10 10 A2 A1A 0 ＊W 14A W13A W12A W11A W0A 10 10A2A1A0 D7 D0 AAss ffoorr WWAA1143,, BBRR2244SS3322//6644/-1W2 8b-eWco bmeeco Dmoen 'Dt coanr'te c. are. R A A A R A A Note) / C *1 C C / C C W K K K W K K Figure 40. Random read cycle (BR24S32/64/128/256-W) ST R S It is necessary to input 'H' A E T to the last ACK. RT ADSDLARVEES S DA DATA(n) OP SDA LINE 1 0 1 0 A2A 1A 0 D7 D0 R A A Note) / C C W K K Figure 41. Current read cycle ARSTT ADSDLARVEES S DRAE DATA(n) DATA(n+x) OPST SDA LINE 1 0 1 0 A2 A1A 0 D7 D0 D7 D0 R A A A A Note） W/ CK CK CK CK Figure 42. Sequential read cycle (in the case of current read cycle) ・In random read cycle, data of designated word address can be read. ・When the command just before current read cycle is random read cycle, current read cycle (each including sequential read cycle), data of incremented last read address (n)-th address, i.e., data of the (n+1)-th address is output. ・When ACK signal 'LOW' after D0 is detected, and stop condition is not sent from master (μ-COM) side, the next address data can be read in succession. ・Read cycle is ended by stop condition where 'H' is input to ACK signal after D0 and SDA signal is started at SCL signal 'H'. ・When 'H' is not input to ACK signal after D0, sequential read gets in, and the next data is output. Therefore, read command cycle cannot be ended. When to end read command cycle, be sure input stop condition to input 'H' to ACK signal after D0, and to start SDA at SCL signal 'H'. ・Sequential read is ended by stop condition where 'H' is input to ACK signal after arbitrary D0 and SDA is started at SCL signal 'H'. Note) *1 BR24S16-W A2 becomes P2. *1 *2 *3 *2 BR24S08/16-W A1 becomes P1. 1 0 1 0 A2 A1A 0 *3 BR24S08/16-W A0 becomes P0. Figure 43. Difference of slave address of each type www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 16/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Software reset Software reset is executed when to avoid malfunction after power on, and to reset during command input. Software reset has several kinds, and 3 kids of them are shown in the figure below. (Refer to Figure 44(a), Figure 44 (b), Figure 44 (c).) In dummy clock input area, release the SDA bus ('H' by pull up). In dummy clock area, ACK output and read data '0' (both 'L' level) may be output from EEPROM, therefore, if 'H' is input forcibly, output may conflict and over current may flow, leading to instantaneous power failure of system power source or influence upon devices. Dummy clock×14 Start×2 SCL 1 2 13 14 Normal command SDA Normalcommand Figure 44-(a) The case of 14 Dummy clock + START + START+ command input Start Dummy clock×9 Start SCL 1 2 8 9 Normal command SDA Normal command Figure 44-(b) The case of START+9 Dummy clock + START + command Start×9 SCL 1 2 3 7 8 9 Normal command SDA Normal command * Start command from START input. Figure 44-(c) START × 9 + command input ●Acknowledge polling During internal write, all input commands are ignored, therefore ACK is not sent back. During internal automatic write execution after write cycle input, next command (slave address) is sent, and if the first ACK signal sends back 'L', then it means end of write action, while if it sends back 'H', it means now in writing. By use of acknowledge polling, next command can be executed without waiting for tWR = 5ms. When to write continuously, R/W = 0, when to carry out current read cycle after write, slave address R/W = 1 is sent, and if ACK signal sends back 'L', then execute word address input and data so forth. During internal write, First write command ACK = HIGH is sent back. S S S T S T A T A A Write command T A Slave A Slave … RT OP RT CK RT dd CK tWR Second write command S S T Slave A T Slave A Word A A S … A C A C C Data C T R address K R address K address K K O T H T L L L P tWR After completion of internal write, ACK=LOW is sent back, so input next word address and data in succession. Figure 45. Case to continuously write by acknowledge polling www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 17/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●WP valid timing (write cancel) WP is usually fixed to 'H' or 'L', but when WP is used to cancel write cycle and so forth, pay attention to the following WP valid timing. During write cycle execution, in cancel valid area, by setting WP='H', write cycle can be cancelled. In both byte write cycle and page write cycle, the area from the first start condition of command to the rise of clock to taken in D0 of data(in page write cycle, the first byte data) is cancel invalid area. WP input in this area becomes Don't care. Set the setup time to rise of D0 taken 100ns or more. The area from the rise of SCL to take in D0 to the end of internal automatic write (tWR) is cancel valid area. And, when it is set WP='H' during tWR, write is ended forcibly, data of address under access is not guaranteed, therefore, write it once again.(Refer to Figure 46.) After execution of forced end by WP standby status gets in, so there is no need to wait for tWR (5ms at maximum). ・Rise of D0 taken clock SCL SCL ・Rise of SDA SDA D1 D0 ACK SDA D0 ACK Enlarged view Enlarged view SDA START aSddlarvees s CAKL aWddorerds s CAKL D7 D6D5D4 D3D2D1 D0 CAKL Data CAKL OSPT tWR WP cancel invalid area WP cancel valid area Write forced end WP Data is not written. Data not guaranteed Figure 46. WP valid timing ●Command cancel by start condition and stop condition During command input, by continuously inputting start condition and stop condition, command can be cancelled. (Refer to Figure 47.) However, in ACK output area and during data read, SDA bus may output 'L', and in this case, start condition and stop condition cannot be input, so reset is not available. Therefore, execute software reset. And when command is cancelled by start, stop condition, during random read cycle, sequential read cycle, or current read cycle, internal setting address is not determined, therefore, it is not possible to carry out current read cycle in succession. When to carry out read cycle in succession, carry out random read cycle. SCL SDA 1 0 1 0 Start condition Figure 47. Case of cancel by start, stop condition during slave address input www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 18/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●I/O peripheral circuit ○Pull up resistance of SDA terminal SDA is NMOS open drain, so requires pull up resistance. As for this resistance value (R ), select an appropriate value to PU this resistance value from microcontroller V , I , and V -I characteristics of this IC. If R is large, action frequency is IL L OL OL PU limited. The smaller the R , the larger the consumption current at action. PU ○Maximum value of R PU The maximum value of R is determined by the following factors. PU (1)SDA rise time to be determined by the capacitance (CBUS) of bus line of R and SDA should be tR or below. PU And AC timing should be satisfied even when SDA rise time is late. ○ (2)The bus electric potential A to be determined by input leak total (I ) of device connected to bus output of 'H' to SDA L bus and R should sufficiently secure the input 'H' level (V ) of microcontroller and EEPROM including recommended PU IH noise margin 0.2Vcc. Vcc - I R - 0.2Vcc ≧ V Microcontroller BR24SXX L PU IH 0.8VCC - VIH ∴ RPU ≦ IL R Ex.) When Vcc = 3V, IL=10μA, VIH = 0.7Vcc PU SDA terminal A from(2) 0.8×3 - 0.7×3 RPU ≦ 10×10-6 IL IL ≦ 30 ［kΩ］ Bus line capacity CBUS ○Minimum value of R PU The minimum value of R is determined by the following factors. PU Figure 48. I/O circuit diagram (1)When IC outputs LOW, it should be satisfied that V =0.4V OLMAX and IOLMAX=3mA. VCC - VOL ≦ IOL RPU VCC - VOL ∴ RPU ≧ IOL (2)V =0.4V should secure the input 'L' level (V ) of microcontroller and EEPROM including recommended noise margin 0.1Vcc. OLMAX IL V ≦ V -0.1 Vcc OLMAX IL Ex.) When Vcc= 3V, V 0.4V, I =3mA, microcontroller, EEPROM V =0.3Vcc OL OL IL from(1), 3－0.4 RPU ≧ 3×10 ≧ 867 ［Ω］ And V =0.4［V］ OL V =0.3×3 IL =0.9［V］ Therefore, the condition (2) is satisfied. ○Pull up resistance of SCL terminal When SCL control is made at CMOS output port, there is no need, but in the case there is timing where SCL becomes 'Hi-Z', add a pull up resistance. As for the pull up resistance, one of several kΩ to several ten kΩ is recommended in consideration of drive performance of output port of microcontroller. ●A0, A1, A2, WP process ○Process of device address terminals (A0,A1,A2) Check whether the set device address coincides with device address input sent from the master side or not, and select one among plural devices connected to a same bus. Connect this terminal to pull up or pull down, or Vcc or GND. And, pins (Don't use PIN) not used as device address may be set to any of ‘H’, 'L', and 'Hi-Z'. Types with Don't use PIN BR24S08F/FJ/FV/FVT/FVM/FVJ/NUX-W A0, A1 BR24S16F/FJ/FV/FVT/FVM/FVJ/NUX-W A0, A1, A2 ○Process of WP terminal WP terminal is the terminal that prohibits and permits write in hardware manner. In 'H' status, only READ is available and WRITE of all address is prohibited. In the case of 'L', both are available. In the case of use it as an ROM, it is recommended to connect it to pull up or Vcc. In the case to use both READ and WRITE, control WP terminal or connect it to pull down or GND. www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 19/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Cautions on microcontroller connection ○Rs In I2C BUS, it is recommended that SDA port is of open drain input/output. However, when to use CMOS input / output of tri state to SDA port, insert a series resistance Rs between the pull up resistance Rpu and the SDA terminal of EEPROM. This is controls over current that occurs when PMOS of the microcontroller and NMOS of EEPROM are turned ON simultaneously. Rs also plays the role of protection of SDA terminal against surge. Therefore, even when SDA port is open drain input/output, Rs can be used. ACK SCL RPU RS SDA 'H' output of microcontroller 'L' output of EEPROM Microcontre EEPROM Over current flows to SDA line by 'H' output of microcontroller and 'L' output of Figure 49. I/O circuit EEPROM. Figure 50. Input/output collision timing ○Maximum value of Rs The maximum value of Rs is determined by following relations. (1)SDA rise time to be determined by the capacity (CBUS) of bus line of Rpu and SDA shoulder be tR or below. And AC timing should be satisfied even when SDA rise time is late. ○ (2)The bus electric potential A to be determined by Rpu and Rs the moment when EEPROM outputs 'L' to SDA bus should sufficiently secure the input 'L' level (V ) of microcontroller including recommended noise margin 0.1Vcc. IL VCC (VCC－VOL)×RS + VOL+0.1VCC≦VIL RPU A RPU+RS RS VOL ∴ RS ≦ VIL－VOL－0.1VCC × RPU IOL 1.1VCC－VIL Example）When VCC=3V, VIL=0.3VCC, VOL=0.4V, RPU=20kΩ Bus line capacity CBUS from(2), RS ≦ 0.3×3－0.4－0.1×3 × 20×103 1.1×3－0.3×3 VIL Microcontroller EEPROM ≦ 1.67［kΩ］ Figure 51. I/O circuit ○Maximum value of Rs The minimum value of Rs is determined by over current at bus collision. When over current flows, noises in power source line, and instantaneous power failure of power source may occur. When allowable over current is defined as I, the following relation must be satisfied. Determine the allowable current in consideration of impedance of power source line in set and so forth. Set the over current to EEPROM 10mA or below. VCC ≦ I RS RP U 'L' output RS VCC ∴ RS ≧ I Over currentⅠ Example）When VCC=3V, I=10mA 'H' output 3 RS ≧ 10×10-3 Microcontroller EEPROM Figure 52. I/O circuit diagram ≧300[Ω] www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 20/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●I2C BUS input / output circuit ○Input (A0, A1, A2, SCL, WP) Figure 53. Input pin circuit diagram ○Input/Output (SDA) Figure 54. Input /output pin circuit diagram ●Notes on power ON At power on, in IC internal circuit and set, Vcc rises through unstable low voltage area, and IC inside is not completely reset, and malfunction may occur. To prevent this, functions of POR circuit and LVCC circuit are equipped. To assure the action, observe the following condition at power on. 1. Set SDA = 'H' and SCL ='L' or 'H' 2. Start power source so as to satisfy the recommended conditions of tR, tOFF, and Vbot for operating POR circuit. tR Recommended conditions of tR,tOFF,Vbot VCC tR tOFF Vbot 10ms or below 10ms or longer 0.3V or below tOFF Vbot 0 100ms or below 10ms or longer 0.2V or below Figure 55. Rise waveform diagram 3. Set SDA and SCL so as not to become 'Hi-Z'. When the above conditions 1 and 2 cannot be observed, take the following countermeasures. a) In the case when the above conditions 1 cannot be observed. When SDA becomes 'L' at power on. → Control SCL and SDA as shown below, to make SCL and SDA, 'H' and 'H'. V CC tLOW SCL SDA After Vcc becomes stable tDH tSU:DAT After Vcc becomes stable tSU:DAT Figure 56. W hen SCL= ' H ' a nd SDA='L' Figure 57 .When SCL= ' H' a nd SDA= 'L ' b) In the case when the above condition 2 cannot be observed. →After power source becomes stable, execute software reset(Page 17). c) In the case when the above conditions 1 and 2 cannot be observed. www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 21/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Low voltage malfunction prevention function LVCC circuit prevents data rewrite action at low power, and prevents wrong write. At LVCC voltage (Typ. =1.2V) or below, it prevent data rewrite. ●Vcc noise countermeasures ○Bypass capacitor When noise or surge gets in the power source line, malfunction may occur, therefore, for removing these, it is recommended to attach a by pass capacitor (0.1μF) between IC Vcc and GND. At that moment, attach it as close to IC as possible. And, it is also recommended to attach a bypass capacitor between board Vcc and GND. ●Notes for Use (1) Described numeric values and data are design representative values, and the values are not guaranteed. (2) We believe that application circuit examples are recommendable, however, in actual use, confirm characteristics further sufficiently. In the case of use by changing the fixed number of external parts, make your decision with sufficient margin in consideration of static characteristics and transition characteristics and fluctuations of external parts and our LSI. (3) Absolute maximum ratings If the absolute maximum ratings such as impressed voltage and action temperature range and so forth are exceeded, LSI may be destructed. Do not impress voltage and temperature exceeding the absolute maximum ratings. In the case of fear exceeding the absolute maximum ratings, take physical safety countermeasures such as fuses, and see to it that conditions exceeding the absolute maximum ratings should not be impressed to LSI. (4) GND electric potential Set the voltage of GND terminal lowest at any action condition. Make sure that each terminal voltage is lower than that of GND terminal. (5) Terminal design In consideration of permissible loss in actual use condition, carry out heat design with sufficient margin. (6) Terminal to terminal shortcircuit and wrong packaging When to package LSI onto a board, pay sufficient attention to LSI direction and displacement. Wrong packaging may destruct LSI. And in the case of shortcircuit between LSI terminals and terminals and power source, terminal and GND owing to foreign matter, LSI may be destructed. (7) Use in a strong electromagnetic field may cause malfunction, therefore, evaluate design sufficiently. Status of this document The Japanese version of this document is formal specification. A customer may use this translation version only for a reference to help reading the formal version. If there are any differences in translation version of this document formal version takes priority. www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 22/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Ordering Information Product Code Description B R 2 4 S x x x x x x - W x x BUS type 24：I2C Operating temperature/ Power source Voltage -40℃ to+85℃/ 1.7V to 5.5V Capacity 08=8K 64=64K 16=16K 128=128K 32=32K 256=256K Package F :SOP8 FJ :SOP-J8 FV : SSOP-B8 FVT : TSSOP-B8 FVJ : TSSOP-B8J FVM : MSOP8 NUX : VSON008X2030 Double Cell Packaging and forming specification E2 : Embossed tape and reel (SOP8,SOP-J8, SSOP-B8,TSSOP-B8, TSSOP-B8J) TR : Embossed tape and reel (MSOP8, VSON008X2030) www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 23/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Physical Dimension Tape and Reel Information SOP8 5.0±0.2 (MAX 5.35 include BURR) +6° 4°−4° 8 7 6 5 5 3 2 N 1 0. 0. MI 0. ± ± ± 2 4 3 9 6. 4. 0. 0. 1 2 3 4 0.595 +0.1 0.17 -0.05 1 . 0 ± S 5 . 1 0.1 S 1 1 . 0 1.27 0.42±0.1 (Unit : mm) <Tape and Reel information> Tape Embossed carrier tape Quantity 2500pcs E2 Direction ( The direction is the 1pin of product is at the upper left when you hold ) of feed reel on the left hand and you pull out the tape on the right hand Direction of feed 1pin Reel ∗ Order quantity needs to be multiple of the minimum quantity. www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 24/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Physical Dimension Tape and Reel Information - continued SOP-J8 4.9±0.2 (MAX 5.25 include BURR) +6° 4°−4° 8 7 6 5 N 3 2 MI 0. 0. 5 ± ± 4 0 9 . 6. 3. 0 1 2 3 4 0.545 0.2±0.1 S 1 . 0 ± 5 7 3 . 1 5 1.27 7 0.42±0.1 1 . 0 0.1 S (Unit : mm) <Tape and Reel information> Tape Embossed carrier tape Quantity 2500pcs E2 Direction ( The direction is the 1pin of product is at the upper left when you hold ) of feed reel on the left hand and you pull out the tape on the right hand Direction of feed 1pin Reel ∗ Order quantity needs to be multiple of the minimum quantity. www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 25/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Physical Dimension Tape and Reel Information - continued SSOP-B8 3.0±0.2 (MAX 3.35 include BURR) 8 7 6 5 32 .. 00 ±± 44 .. 64 N I M 3 . 0 1 2 3 4 1 0.15±0.1 0. ± 5 S 1 1. 0.1 S 1 +0.06 0. (0.52) 0.65 0.22−0.04 0.08 M (Unit : mm) <Tape and Reel information> Tape Embossed carrier tape Quantity 2500pcs E2 Direction ( The direction is the 1pin of product is at the upper left when you hold ) of feed reel on the left hand and you pull out the tape on the right hand Direction of feed 1pin Reel ∗ Order quantity needs to be multiple of the minimum quantity. www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 26/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Physical Dimension Tape and Reel Information - continued TSSOP-B8 3.0±0.1 (MAX 3.35 include BURR) 4 ± 4 8 7 6 5 2 1 . . 0 0 ± ± 4 4 6. 4. 5 1 . 0 ± 5 2 0. 0. ± 0 1 2 3 4 1. 1PIN MARK +0.05 0.525 0.145−0.03 5 X A .0 S M 0 ± 2 0 . 1 . 1 5 0 0.08 S . 0 +0.05 ±1 0.245−0.04 0.08 M . 0 0.65 (Unit : mm) <Tape and Reel information> Tape Embossed carrier tape Quantity 3000pcs E2 Direction ( The direction is the 1pin of product is at the upper left when you hold ) of feed reel on the left hand and you pull out the tape on the right hand Direction of feed 1pin Reel ∗ Order quantity needs to be multiple of the minimum quantity. www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 27/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Physical Dimension Tape and Reel Information - continued TSSOP-B8J 3.0±0.1 (MAX 3.35 include BURR) 4 ± 4 8 7 6 5 2 1 0. 0. ± ± 9 0 4. 3. 15 . 0 ± 5 2 4 . 0 . 0 ± 5 9 . 1 2 3 4 0 1PIN MARK +0.05 X 5 0.525 0.145−0.03 A 0 . M 0 S ± 1 5 1. 8 . 5 0 0 0.08 S . 0 +0.05 ±1 0.32−0.04 0.08 M . 0 0.65 (Unit : mm) <Tape and Reel information> Tape Embossed carrier tape Quantity 2500pcs E2 Direction ( The direction is the 1pin of product is at the upper left when you hold ) of feed reel on the left hand and you pull out the tape on the right hand Direction of feed 1pin Reel ∗ Order quantity needs to be multiple of the minimum quantity. www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 28/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Physical Dimension Tape and Reel Information - continued MSOP8 2.9±0.1 (MAX 3.25 include BURR) + 6° 4°−4° 5 2 8 7 6 5 1 0. 0. ± ± 6 2 1 9 0. 0. 0. .2 ± ± 0 0 8 4. 2. 1 2 3 4 1PIN MARK +0.05 0.145−0.03 0.475 S X A M 9 +0.05 . 0 0.22 −0.04 5 5 0 0 . . 0 0 0.08 S ± ± 5 8 7 0 . . 0.65 0 0 (Unit : mm) <Tape and Reel information> Tape Embossed carrier tape Quantity 3000pcs TR Direction ( The direction is the 1pin of product is at the upper right when you hold ) of feed reel on the left hand and you pull out the tape on the right hand 1pin Direction of feed Reel ∗ Order quantity needs to be multiple of the minimum quantity. www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 29/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Physical Dimension Tape and Reel Information - continued VSON008X2030 2.0±0.1 1 . 0 ± 0 . 3 1PIN MARK X S A M 6 . 32 0 00 2) 0.0. 1 +− 0. 0.08 S 2 ( 1.5±0.1 0 . 0 0.5 C0.25 1 0. 1 4 ± 1 3 0. 0. ± 4 . 1 8 5 0.25 +0.05 0.25−0.04 (Unit : mm) <Tape and Reel information> Tape Embossed carrier tape Quantity 4000pcs TR Direction of feed ( The direction is the 1pin of product is at the upper right when you hold ) reel on the left hand and you pull out the tape on the right hand 1pin Direction of feed Reel ∗ Order quantity needs to be multiple of the minimum quantity. www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 30/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Marking Diagrams SOP8(TOP VIEW) SOP-J8(TOP VIEW) Part Number Marking Part Number Marking LOT Number LOT Number 1PIN MARK 1PIN MARK SSOP-B8(TOP VIEW) TSSOP-B8(TOP VIEW) Part Number Marking Part Number Marking LOT Number LOT Number 1PIN MARK 1PIN MARK TSSOP-B8J(TOP VIEW) MSOP8(TOP VIEW) Part Number Marking Part Number Marking LOT Number LOT Number 1PIN MARK 1PIN MARK VSON008X2030 (TOP VIEW) Part Number Marking LOT Number 1PIN MARK www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 31/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Marking Information Product Name Capacity Package Type Marking S08 SOP8 S08 SOP-J8 S08 SSOP-B8 8K S08 TSSOP-B8 S08 TSSOP-B8J S08 MSOP8 S08 VSON008X2030 S16 SOP8 S16 SOP-J8 S16 SSOP-B8 16K S16 TSSOP-B8 S16 TSSOP-B8J S16 MSOP8 S16 VSON008X2030 S32 SOP8 S32 SOP-J8 S32 SSOP-B8 32K S32 TSSOP-B8 S32 TSSOP-B8J S32 MSOP8 S32 VSON008X2030 S64 SOP8 S64 SOP-J8 S64 SSOP-B8 64K S64 TSSOP-B8 S64 TSSOP-B8J S64 MSOP8 4S128 SOP8 4S128 SOP-J8 128K S128 SSOP-B8 4S128 TSSOP-B8 4S256 SOP8 256K 4S256 SOP-J8 www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 32/33 TSZ22111･15･001 20.AUG.2012 Rev.001

BR24Sxxx-W (8K 16K 32K 64K 128K 256K) Datasheet ●Revision History Date Revision Changes 20.Aug.2012 001 New Release www.rohm.com TSZ02201-0R2R0G100320-1-2 ©2012 ROHM Co., Ltd. All rights reserved. 33/33 TSZ22111･15･001 20.AUG.2012 Rev.001

DDaattaasshheeeett Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice - GE Rev.002 © 2014 ROHM Co., Ltd. All rights reserved.

DDaattaasshheeeett Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice - GE Rev.002 © 2014 ROHM Co., Ltd. All rights reserved.

DDaattaasshheeeett General Precaution 1. Before you use our Products, you are requested to carefully read this document and fully understand its contents. ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this document is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sale s representative. 3. The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or concerning such information. Notice – WE Rev.001 © 2014 ROHM Co., Ltd. All rights reserved.

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: R OHM Semiconductor: BR24S08FJ-WE2 BR24S08FVT-WE2 BR24S128FJ-WE2 BR24S16FJ-WE2 BR24S16FVT-WE2 BR24S32FJ-WE2 BR24S32FVT-WE2 BR24S32F-WE2 BR24S64FJ-WE2 BR24S64FVT-WE2 BR24S256FJ-WE2 BR24S128FVT- WE2 BR24S08F-WE2 BR24S128FV-WE2 BR24S128F-WE2 BR24S16FVM-WTR BR24S16F-WE2 BR24S256F- WE2 BR24S32FVM-WTR BR24S64FVM-WTR BR24S64F-WE2 BR24S16NUX-WTR BR24S32NUX-WTR BR24S08FVJ-WE2 BR24S08NUX-WTR BR24S08FV-WE2 BR24S16FVJ-WE2 BR24S32FV-WE2 BR24S64FV-WE2 BR24S32FVJ-WE2 BR24S64FVJ-WE2 BR24S16FV-WE2 BR24S08FVM-WTR