Reference Only Spec.No.JENF243A-9103K-01 P1/8 Chip Ferrite Bead BLM15□□□□□SH1D Reference Specification [AEC-Q200] 1.Scope This reference specification applies to Chip Ferrite Bead BLM15_SH series for Automotive Electronics based on AEC-Q200. 2.Part Numbering (ex.) BL M 15 AG 102 S H 1 D (1) (2) (3) (4) (5) (6) (7) (8) (9) (1)Product ID (4)Characteristics (7)Category(for Automotive Electronics) (2)Type (5)Typical Impedance at 100MHz (8)Numbers of Circuit (3)Dimension (L×Ｗ) (6)Performance (9)Packaging (D:Taping) 3.Rating DC Resistance (Ω max.) (*1) Impedance (Ω) Rated (refer to below Customer MURATA ESD Rank (at 100MHz)(*1) Current comment) Part Number Part Number 2 :2kV (refer to below comment) (mA) Initial Values Values After Testing BLM15AG100SH1D 5～15 1000 0.05 0.10 BLM15AG700SH1D 40～100 500 0.15 0.20 BLM15AG121SH1D 120±25% 500 0.25 0.35 BLM15AG221SH1D 220±25% 300 0.35 0.45 BLM15AG601SH1D 600±25% 300 0.60 0.70 BLM15AG102SH1D 1000±25% 200 1.0 1.1 BLM15BB050SH1D 5±25% 500 0.08 0.15 BLM15BB100SH1D 10±25% 300 0.10 0.15 BLM15BB220SH1D 22±25% 300 0.20 0.30 2 BLM15BB470SH1D 47±25% 300 0.35 0.45 BLM15BB750SH1D 75±25% 300 0.40 0.50 BLM15BB121SH1D 120±25% 300 0.55 0.65 BLM15BB221SH1D 220±25% 200 0.80 0.90 BLM15BD471SH1D 470±25% 200 0.60 0.70 BLM15BD601SH1D 600±25% 200 0.65 0.75 BLM15BD102SH1D 1000±25% 200 0.90 1.0 BLM15BD182SH1D 1800±25% 200 1.4 1.5 ■Operating Temperature : -55°C to +125°C ■Storage Temperature : -55°C to +125°C (*1) Standard Testing Conditions < Unless otherwise specified > < In case of doubt > Temperature : Ordinary Temp. (15 °C to 35 °C ) Temperature : 20°C±2 °C Humidity : Ordinary Humidity (25%(RH) to 85%(RH)) Humidity : 60%(RH) to 70%(RH) Atmospheric pressure : 86kPa to 106kPa 4.Style and Dimensions 1.0±0.05 0.5±0.05 ■ Equivalent Circuit 5 0 ±0. 5 0. 0.25±0.1 ( ) Resistance element becomes dominant at high frequencies. : Electrode ■ Unit Weight (Typical value) (inmm) 0.001g MURATA MFG.CO.,LTD.

Reference Only Spec.No.JENF243A-9103K-01 P2/8 5.Marking No marking. 6.Specifications 6-1.Electrical Performance No. Item Specification Test Method 6-1-1 Impedance Meet item 3. Measuring Frequency : 100MHz±1MHz Measuring Equipment : KEYSIGHT4291A or the equivalent Test Fixture : KEYSIGHT16192A or the equivalent 6-1-2 DC Resistance Meet item 3. Measuring Equipment : Digital multi meter *Except resistance of the Substrate and Wire 6-2.Mechanical Performance (based on Table 13 for FILTER EMI SUPPRESSORS/FILTERS) AEC-Q200 Rev.D issued June. 1 2010 AEC-Q200 Murata Specification / Deviation No. Stress Test Method 3 High 1000hours at 125 deg C Meet Table A after testing. Temperature Set for 24hours Table A Exposure at room temperature, Appearance No damage then measured. Impedance Change Within ±30% (at 100MHz) DC Meet item 3. Resistance 4 Temperature Cycling 1000cycles Meet Table A after testing. -55 deg C to +125 deg C Set for 24hours at room temperature, then measured. 5 Destructive Per EIA469 No defects Physical Analysis No electrical tests 7 Biased Humidity 1000hours at 85 deg C, 85%RH Meet Table A after testing. Apply max rated current. MURATA MFG.CO.,LTD.

Reference Only Spec.No.JENF243A-9103K-01 P3/8 AEC-Q200 Murata Specification / Deviation No. Stress Test Method 8 Operational Life Apply 125 deg C 1000hours Meet Table A after testing. Set for 24hours at If the rated current of parts exceed 1A, room temperature, the operating temperature should be 85 deg C. then measured 9 External Visual Visual inspection No abnormalities 10 Physical Dimension Meet ITEM 4 No defects （Style and Dimensions） 12 Resistance Per MIL-STD-202 Method 215 Not Applicable to Solvents 13 Mechanical Shock Per MIL-STD-202 Method 213 Meet Table A after testing. Condition F: 1500g's(14.7N)/0.5ms/Half sine 14 Vibration 5g's(0.049N) for 20 minutesMeet Table A after testing. 12cycles each of 3 oritentations Test from 10-2000Hz. 15 Resistance Solder temperature Pre-heating: 150C +/-10 deg C, 60s to 90s to Soldering Heat 260C+/-5 deg C Immersion time 10s Meet Table A after testing. 17 ESD Per AEC-Q200-002 ESD Rank: Meet Item 3 (Rating) BLM15AG sereis: Meet Table A after testing. BLM15BB/BD series: Meet Table B after testing. Table B Appearance No damage Impedance Change Within ±40% (at 100MHz) DC Meet item 3. Resistance 18 Solderability Per J-STD-002 Method b : Not Applicable 95% of the terminations is to be soldered. 19 Electrical Measured : Impedance No defects Characterization 20 Flammability Per UL-94 Not Applicable 21 Board Flex Epoxy-PCB(1.6mm) Meet Table A after testing. Deflection 2mm(min) 60s minimum holding time 22 Terminal Strength Per AEC-Q200-006 Murata deviation request: 5N No defects 30 Electrical Per ISO-7637-2 Not Applicable Transient Conduction MURATA MFG.CO.,LTD.

Reference Only Spec.No.JENF243A-9103K-01 P4/8 7.Specification of Packaging 7-1.Appearance and Dimensions (8mm-wide paper tape) 1 2.0±0.05 0. 2.0±0.05 4.0±0.1 φ1.5+0.1 5± -0 7 . 1 5 0 Typ.) 3.5±0. ±0.3 5( 8.0 1 . 1 0.65(Typ.) 0.8max. Directionof Feed (inmm) (1) Taping Products shall be packaged in the cavity of the base tape of 8mm-wide, 2mm-pitch continuously and sealed by top tape and bottom tape. (2) Sprocket hole:Sprocket hole shall be located on the left hand side toward the direction of feed. (3) Spliced point:The base tape and top tape have no spliced point (4) Cavity:There shall not be burr in the cavity. (5) Missing components number Missing components number within 0.025% of the number per reel or 1 pc., whichever is greater, and are not continuous. The specified quantity per reel is kept.. 7-2.Tape Strength (1)Pull Strength Top tape 5N min. Bottom tape Top tape 165to180degree F (2)Peeling off force of Cover tape 0.1N to 0.6N (Minimum value is typical.) *Speed of Peeling off:300mm/min Bottomtape Base tape 7-3.Taping Condition (1)Standard quantity per reel Quantity per 180mm reel 10000 pcs. / reel (2)There shall be leader-tape(top tape and empty tape) and trailer- tape(empty tape) as follows. (3)On paper tape, the top tape and the base tape shall not be adhered at the tip of the empty leader tape for more than 5 pitch. (4)Marking for reel The following items shall be marked on a label and the label is stuck on the reel. (Customer part number, MURATA part number, Inspection number(∗1) , RoHS marking(∗2) , Quantity, etc) ∗1) « Expression of Inspection No. » □□ OOOO ××× (1) (2) (3) (1) Factory Code (2) Date First digit : Year / Last digit of year Second digit : Month / Jan. to Sep. → 1 to 9, Oct. to Dec. → O,N,D Third, Fourth digit : Day (3) Serial No. ∗2) « Expression of RoHS marking » ROHS – Y (△) (1) (2) (1) RoHS regulation conformity parts. (2) MURATA classification number (5)Outside package These reels shall be packed in the corrugated cardboard package and the following items shall be marked on a label and the label is stuck on the box. (Customer name, Purchasing order number, Customer part number, MURATA part number, RoHS marking(∗2) ,Quantity, etc) MURATA MFG.CO.,LTD.

Reference Only Spec.No.JENF243A-9103K-01 P5/8 (6)Dimensions of reel and taping(leader-tape, trailer-tape) Trailer 160min. Leader 2.0±0.5 Label 190min. 210min. Emptytape Toptape φ13.0±0.2 φ60+-10 Directionof feed φ21.0±0.8 9.0+1 -0 13.0±1.4 φ180+0 -3 (in mm) 7-4. Specification of Outer Case Outer Case Dimensions Label Standard Reel Quantity in Outer Case (mm) (Reel) H W D H 186 186 93 5 D ∗ Above Outer Case size is typical. It is depend on a quantity of an W order. 8. ！ Caution 8-1.Rating Do not use products beyond the Operating Temperature Range and Rated Current. 8-2.Surge current Excessive surge current (pulse current or rush current) than specified rated current applied to the product may cause a critical failure, such as an open circuit, burnout caused by excessive temperature rise. Please contact us in advance in case of applying the surge current. 8-3.Fail Safe Be sure to provide an appropriate fail-safe function on your product to prevent from a second damage that may be caused by the abnormal function or the failure of our products. 8-4.Limitation of Applications Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property. (1)Aircraft equipment (6)Disaster prevention / crime prevention equipment (2)Aerospace equipment (7)Traffic signal equipment (3)Undersea equipment (8)Transportation equipment (trains, ships, etc.) (4)Power plant control equipment (9) Data-processing equipment (5)Medical equipment (10)Applications of similar complexity and /or reliability requirements to the applications listed in the above MURATA MFG.CO.,LTD.

Reference Only Spec.No.JENF243A-9103K-01 P6/8 9. Notice This product is designed for solder mounting. Please consult us in advance for applying other mounting method such as conductive adhesive. 9-1.Land pattern designing • Standard land dimensions (Reflow soldering) ChipFerriteBead c a SolderResist Soldering a b c b Pattern Reflow 0.4 1.2 0.5 (in mm) 9-2.Soldering Conditions Products can be applied to reflow soldering. (1) Flux,Solder Flux Use rosin-based flux, but not highly acidic flux (with chlorine content exceeding 0.2(wt)%. ) Do not use water-soluble flux. Solder Use Sn-3.0Ag-0.5Cu solder Standard thickness of solder paste : 100 µm to 200 μm (2) Soldering conditions • Pre-heating should be in such a way that the temperature difference between solder and ferrite surface is limited to 150℃ max. Also cooling into solvent after soldering should be in such a way that the temperature difference is limited to 100℃ max. Insufficient pre-heating may cause cracks on the ferrite, resulting in the deterioration of product quality. • Standard soldering profile and the limit soldering profile is as follows. The excessive limit soldering conditions may cause leaching of the electrode and / or resulting in the deterioration of product quality. (3) Soldering profile Temp. 260℃ (℃) 245℃±3℃ 230℃ 220℃ Limit Profile 180 150 30s～60s Standard Profile 60s max. 90s±30s Time.(s) Standard Profile Limit Profile Pre-heating 150～180°C 、90s±30s Heating above 220°C、30s～60s above 230°C、60s max. Peak temperature 245±3°C 260°C,10s Cycle of reflow 2 times 2 times 9-3. Soldering iron • Pre-heating: 150°C, 1 min • Soldering iron output: 80W max. • Tip temperature: 350°C max. • Tip diameter:φ3mm max. • Soldering time : 3(+1,-0) seconds. • Times : 2times max. Note :Do not directly touch the products with the tip of the soldering iron in order to prevent the crack on the ferrite material due to the thermal shock. MURATA MFG.CO.,LTD.

Reference Only Spec.No.JENF243A-9103K-01 P7/8 9-4.Solder Volume Solder shall be used not to be exceeded as shown below. UpperLimit Recommendable t 1/3T≦t≦T (T:Chip thickness) Accordingly increasing the solder volume, the mechanical stress to product is also increased. Exceeding solder volume may cause the failure of mechanical or electrical performance. 9-5.Attention regarding P.C.B. bending The following shall be considered when designing and laying out P.C.B.'s. (1) P.C.B. shall be designed so that products are not subject to the mechanical stress for board warpage. <Products direction> a Products shall be located in the sideways b direction (Length:a<b) to the mechanical stress. 〈Poorexample〉 〈Goodexample〉 (2) Components location on P.C.B. separation. It is effective to implement the following measures, to reduce stress in separating the board. It is best to implement all of the following three measures; however, implement as many measures as possible to reduce stress. Contents of Measures Stress Level (1) Turn the mounting direction of the component parallel to the board separation surface. A > D *1 (2) Add slits in the board separation part. A > B (3) Keep the mounting position of the component away from the board separation surface. A > C C Perforation B D A Slit *1 A > D is valid when stress is added vertically to the perforation as with Hand Separation. If a Cutting Disc is used, stress will be diagonal to the PCB, therefore A > D is invalid. (3) Mounting Components Near Screw Holes When a component is mounted near a screw hole, it may be affected by the board deflection that occurs during the tightening of the screw. Mount the component in a position as far away from the screw holes as possible. Screw Hole Recommended 9-6.Mounting density Add special attention to radiating heat of products when mounting the inductor near the products with heating. The excessive heat by other products may cause deterioration at joint of this product with substrate. MURATA MFG.CO.,LTD.

Reference Only Spec.No.JENF243A-9103K-01 P8/8 9-7. Operating Environment Do not use this product under the following environmental conditions, on deterioration of the Insulation Resistance of the Ferrite material and/or corrosion of Inner Electrode may result from the use. (1) in the corrodible atmosphere such as acidic gases, alkaline gases, chlorine, sulfur gases, organic gases and etc. (the sea breeze, Cl2, H2S, NH3, SO2, NO2,etc) (2) in the atmosphere where liquid such as organic solvent, may splash on the products. (3) in the atmosphere where the temperature / humidity changes rapidly and it is easy to dew. 9-8. Resin coating The impedance value may change and/or it may affect on the product's performance due to high cure-stress of resin to be used for coating / molding products. So please pay your careful attention when you select resin. In prior to use, please make the reliability evaluation with the product mounted in your application set. 9-9.Cleaning Conditions Products shall be cleaned on the following conditions. (1)Cleaning temperature shall be limited to 60°C max. (40°C max. for IPA.) (2)Ultrasonic cleaning shall comply with the following conditions, avoiding the resonance phenomenon at the mounted products and P.C.B. Power:20W/ max. Frequency:28kHz to 40kHz Time:5 min max. (3)Cleaner 1.Alternative cleaner •Isopropyl alcohol (IPA) 2.Aqueous agent •PINE ALPHA ST-100S (4)There shall be no residual flux and residual cleaner after cleaning. In the case of using aqueous agent, products shall be dried completely after rinse with de-ionized water in order to remove the cleaner. (5)Other cleaning Please contact us. 9-10. Handling of a substrate After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to the substrate. Excessive mechanical stress may cause cracking in the product. Bending Twisting 9-11.Storage Conditions (1)Storage period Use the products within 6 months after delivered. Solderability should be checked if this period is exceeded. (2)Storage conditions • Products should be stored in the warehouse on the following conditions. Temperature : -10°C to 40°C Humidity : 15% to 85% relative humidity No rapid change on temperature and humidity • Don't keep products in corrosive gases such as sulfur, chlorine gas or acid, or it may cause oxidization of electrode, resulting in poor solderability. • Products should be stored on the palette for the prevention of the influence from humidity, dust and so on. • Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on. • Products should be stored under the airtight packaged condition. (3)Delivery Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock. 10 . ! Note (1)Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. (2)You are requested not to use our product deviating from the agreed specifications. (3)The contents of this reference specification are subject to change without advance notice. Please approve our product specifications or transact the approval sheet for product specifications before ordering. MURATA MFG.CO.,LTD.