Datasheet Ground Sense Comparator BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series General Description Key Specifications General purpose BA8391G/BA10393F/BA10339xx  Operating Supply Voltage(Single Supply): and high reliability BA2903xxxx/BA2901xxx integrate BA8391G/BA10393F +2.0V to +36.0V one, two or four independent high gain voltage BA2903xxxx/BA2901xxx +2.0V to +36.0V comparator. BA10339xx +3.0V to +36.0V Operating supply voltage range of BA8391G/BA1039  Operating Supply Voltage(Split Supply): 3F/BA2903xxxx/BA2901xxx is wide(2V to 36V). BA8391G/BA10393F ±1.0V to ±18.0V And can be used in a variety of applications because BA2903xxxx/BA2901xxx ±1.0V to ±18.0V current consumption is small. BA2903Wxx is a low BA10339xx ±1.5V to ±18.0V input offset voltage products.(2mV max)  Temperature Range: BA8391G/BA10393F/BA10339xx -40°C to +85°C Features BA2903Sxxx/BA2901Sxx -40°C to +105°C  Operable with a Single Power Supply BA2903xxx/BA2901xx -40°C to +125°C  Wide Operating Supply Voltage  Input Offset Voltage:  Standard Pin Assignments BA2903Sxxx/BA2901Sxx 7mV(Max)  Input and Output are Ground Sense Operated BA8391G/BA2903xxx/BA2901xx 7mV(Max)  Open Collector BA10393F/BA10339xx 5mV(Max)  Wide Temperature Range BA2903Wxx 2mV(Max) Application Packages W(Typ) x D(Typ) x H(Max)  General Use SSOP5 2.90mm x 2.80mm x 1.25mm  Current Monitor SOP8 5.00mm x 6.20mm x 1.71mm  Battery Monitor SSOP-B8 3.00mm x 6.40mm x 1.35mm  Multi vibrator MSOP8 2.90mm x 4.00mm x 0.90mm SOP14 8.70mm x 6.20mm x 1.71mm SSOP-B14 5.00mm x 6.40mm x 1.35mm Selection Guide Maximum operating temperature Input Offset Voltage +85°C +105°C +125°C (Max) General Purpose Single 7mV BA8391G Dual 5mV BA10393F BA10339F Quad 5mV BA10339FV BA2903SF BA2903F High Reliability Dual 7mＶ BA2903SFV BA2903FV BA2903SFVM BA2903FVM 2mV BA2903WF BA2903WFV BA2901SF BA2901F Quad 7mV BA2901SFV BA2901FV 〇Product structure : Silicon monolithic integrated circuit 〇This product has no designed protection against radioactive rays w ww.rohm.com TSZ02201-0RFR0G200200-1-2 © 2013 ROHM Co., Ltd. All rights reserved. 1/53 TSZ22111 • 14 • 001 05.Jun.2015 Rev.004

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Simplified Schematic VCC OUT +IN -IN VEE Figure 1. Simplified Schematic (one channel only) Pin Configuration BA8391G : SSOP5 Pin No. Pin Name -IN 1 5 VCC 1 -IN 2 VEE VEE 2 - + 3 +IN 4 OUT +IN 3 4 OUT 5 VCC BA10393F, BA2903SF, BA2903F, BA2903WF : SOP8 BA2903SFV, BA2903FV, BA2903WFV : SSOP-B8 BA2903SFVM,BA2903FVM : MSOP8 Pin No. Pin Name 1 OUT1 OUT1 1 8 VCC 2 -IN1 -IN1 2 CH1 7 OUT2 3 +IN1 - + 4 VEE +IN1 3 6 -IN2 5 +IN2 CH2 + - 6 -IN2 VEE 4 5 +IN2 7 OUT2 8 VCC www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 2/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Pin Configuration - continued BA10339F, BA2901SF, BA2901F : SOP14 BA10339FV, BA2901SFV, BA2901FV : SSOP-B14 Pin No. Pin Name OUT2 1 14 OUT3 1 OUT2 2 OUT1 OUT1 2 13 OUT4 3 VCC 4 -IN1 VCC 3 12 VEE 5 +IN1 -IN1 4 －CH1＋ －CH4＋ 11 +IN4 6 -IN2 7 +IN2 +IN1 5 10 -IN4 8 -IN3 9 +IN3 -IN2 6 9 +IN3 －CH2＋ －CH3＋ 10 -IN4 +IN2 7 8 -IN3 11 +IN4 12 VEE 13 OUT4 14 OUT3 Package SSOP5 SOP8 SSOP-B8 MSOP8 SOP14 SSOP-B14 BA8391G BA10393F BA2903SFV BA2903SFVM BA10339F BA10339FV BA2903SF BA2903FV BA2903FVM BA2901SF BA2901SFV BA2903F BA2903WFV BA2901F BA2901FV BA2903WF Ordering Information B A x x x x x x x x - x x Part Number Package Packaging and forming specification BA8391 G : SSOP5 E2: Embossed tape and reel BA10393xx F : SOP8 (SOP8/SOP14/SSOP-B8/SSOP-B14) BA10339xx SOP14 TR: Embossed tape and reel BA2901xx FV : SSOP-B8 (SSOP5/MSOP8) BA2901Sxx SSOP-B14 BA2903xx FVM : MSOP8 BA2903Sxx BA2903Wxx www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 3/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Line-up Input Offset Supply Orderable Operating Temperature Range Voltage Current Package Part Number (Max) (Typ) 7mV 0.3mA SSOP5 Reel of 3000 BA8391G-TR 0.4mA SOP8 Reel of 2500 BA10393F-E2 -40°C to +85°C 5mV SOP14 Reel of 2500 BA10339F-E2 0.8mA SSOP-B14 Reel of 2500 BA10339FV-E2 SOP8 Reel of 2500 BA2903SF-E2 0.6mA SSOP-B8 Reel of 2500 BA2903SFV-E2 -40°C to +105°C MSOP8 Reel of 3000 BA2903SFVM-TR SOP14 Reel of 2500 BA2901SF-E2 7mV 0.8mA SSOP-B14 Reel of 2500 BA2901SFV-E2 SOP8 Reel of 2500 BA2903F-E2 SSOP-B8 Reel of 2500 BA2903FV-E2 0.6mA MSOP8 Reel of 3000 BA2903FVM-TR -40°C to +125°C SOP8 Reel of 2500 BA2903WF-E2 2mV SSOP-B8 Reel of 2500 BA2903WFV-E2 SOP14 Reel of 2500 BA2901F-E2 7mV 0.8mA SSOP-B14 Reel of 2500 BA2901FV-E2 Absolute Maximum Ratings (Ta=25°C) Rating Parameter Symbol Unit BA8391G Supply Voltage VCC-VEE +36 V Power Dissipation PD SSOP5 0.67 (Note1,2) W Differential Input Voltage (Note 3) VID +36 V Input Common-mode Voltage Range VICM (VEE-0.3) to (VEE+36) V Input Current (Note 4) II -10 mA +2.0 to +36.0 Operating Supply Voltage Vopr (±1.0 to ±18.0) V Operating Temperature Range Topr -40 to +85 °C Storage Temperature Range Tstg -55 to +150 °C Maximum Junction Temperature Tjmax +150 °C (Note 1) To use at temperature above TA＝25°C reduce 5.4mW. (Note 2) Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm). (Note 3) The voltage difference between inverting input and non-inverting input is the differential input voltage. Then input terminal voltage is set to more than VEE. (Note 4) Excessive input current will flow if a differential input voltage in excess of approximately 0.6V is applied between the input unless some limiting resistance is used. Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 4/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Absolute Maximum Ratings - continued Rating Parameter Symbol Unit BA10393F BA10339xx Supply Voltage VCC-VEE +36 V SOP8 0.62 (Note 5,8) - Power Dissipation PD SOP14 - 0.49 (Note 6,8) W SSOP-B14 - 0.70 (Note 7,8) Differential Input Voltage(Note 9) VID (VEE to VCC) V Input Common-mode Voltage Range VICM (VEE-0.3) to VCC V Input Current(Note 10) II -10 mA +2.0 to +36.0 +3.0 to +36.0 Operating Supply Voltage Vopr (±1.0 to ±18.0) (±1.5 to ±18.0) V Operating Temperature Range Topr -40 to +85 °C Storage Temperature Range Tstg -55 to +125 °C Maximum Junction Temperature Tjmax +125 °C (Note 5) To use at temperature above TA＝25°C reduce 6.2mW. (Note 6) To use at temperature above TA＝25°C reduce 4.9mW. (Note 7) To use at temperature above TA＝25°C reduce 7.0mW. (Note 8) Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm). (Note 9) The voltage difference between inverting input and non-inverting input is the differential input voltage. Then input terminal voltage is set to more than VEE. (Note 10) Excessive input current will flow if a differential input voltage in excess of approximately 0.6V is applied between the input unless some limiting resistance is used. Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. Rating Parameter Symbol Unit BA2903Sxxx BA2901Sxx BA2903xxx BA2901xx Supply Voltage VCC-VEE +36 V SOP8 0.77 (Note 11,16) - 0.77 (Note 11,16) - SSOP-B8 0.68 (Note 12,16) - 0.68 (Note 12,16) - Power Dissipation PD MSOP8 0.58 (Note 13,16) - 0.58 (Note 13,16) - W SOP14 - 0.61 (Note 14,16) - 0.61 (Note 14,16) SSOP-B14 - 0.87 (Note 15,16) - 0.87 (Note 15,16) Differential Input Voltage (Note 17) VID 36 V Input Common-mode Voltage Range VICM (VEE-0.3) to (VEE+36) V Input Current (Note 18) II -10 mA +2.0 to +36.0 Operating Supply Voltage Vopr (±1.0 to ±18.0) V Operating Temperature Range Topr -40 to +105 -40 to +125 °C Storage Temperature Range Tstg -55 to +150 °C Maximum Junction Temperature Tjmax +150 °C (Note 11) To use at temperature above TA＝25°C reduce 6.2mW. (Note 12) To use at temperature above TA＝25°C reduce 5.5mW. (Note 13) To use at temperature above TA＝25°C reduce 4.7mW. (Note 14) To use at temperature above TA＝25°C reduce 4.9mW. (Note 15) To use at temperature above TA＝25°C reduce 7.0mW. (Note 16) Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm). (Note 17) The voltage difference between inverting input and non-inverting input is the differential input voltage. Then input terminal voltage is set to more than VEE. (Note 18) Excessive input current will flow if a differential input voltage in excess of approximately 0.6V is applied between the input unless some limiting resistance is used. Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 5/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Electrical Characteristics ○BA8391G(Unless otherwise specified VCC=+5V, VEE=0V, TA=25°C) Temperature Limit Parameter Symbol Unit Conditions Range Min Typ Max 25°C - 2 7 OUT=1.4V Input Offset Voltage (Note 19,20) VIO mV Full range - - 15 VCC=5 to 36V, OUT=1.4V 25°C - 5 50 Input Offset Current (Note 19,20) IIO nA OUT=1.4V Full range - - 200 25°C - 50 250 Input Bias Current (Note 20,21) IB nA OUT=1.4V Full range - - 500 Input Common-mode VCC VICM 25°C 0 - V - Voltage Range -1.5 25 100 - V/mV VCC=15V, OUT=1.4 to 11.4V Large Signal Voltage Gain AV 25°C 88 100 - dB RL=15kΩ, VRL=15V 25°C - 0.3 0.7 OUT=Open Supply Current (Note 20) ICC mA Full range - - 1.3 OUT=Open, VCC=36V +IN=0V, -IN=1V Output Sink Current(Note 22) ISINK 25°C 6 16 - mA OUT=1.5V Output Saturation Voltage (Note 20) 25°C - 150 400 +IN= 0V, -IN=1V VOL mV (Low Level Output Voltage) Full range - - 700 ISINK=4mA +IN=1V, -IN=0V 25°C - 0.1 - nA Output Leakage Current (Note 20) OUT=5V ILEAK (High Level Output Current) +IN=1V, -IN=0V Full range - - 1 μA OUT=36V RL=5.1kΩ, VRL=5V - 1.3 - IN=100mVP-P, Overdrive=5mV Response Time tRE 25°C μs RL=5.1kΩ, VRL=5V, IN=TTL - 0.4 - Logic Swing, VREF=1.4V (Note 19) Absolute value (Note 20) Full range TA=-40°C to +85°C (Note 21) Current Direction: Because the first stage is composed with PNP transistor, input bias current flows out of IC. (Note 22) Please determine the output current value in consideration of the power dissipation of the IC under high temperature environment. When the output terminal is continuously shorted, output current may be reduced by the temperature rise of the IC. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 6/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Electrical Characteristics - continued ○BA10393F (Unless otherwise specified VCC=+5V, VEE=0V, TA=25°C) Temperature Limit Parameter Symbol Unit Conditions Range Min Typ Max Input Offset Voltage (Note 23) VIO 25°C - 1 5 mV OUT=1.4V Input Offset Current (Note 23) IIO 25°C - 5 50 nA OUT=1.4V Input Bias Current (Note 24) IB 25°C - 50 250 nA OUT=1.4V Input Common-mode VCC VICM 25°C 0 - V - Voltage Range -1.5 50 200 - V/mV VCC=15V, OUT=1.4 ~ 11.4V Large Signal Voltage Gain AV 25°C 94 106 - dB RL=15kΩ, VRL=15V Supply Current ICC 25°C - 0.4 1 mA RL=∞, All Comparators -IN=1V, +IN=0V Output Sink Current (Note 25) ISINK 25°C 6 16 - mA OUT=1.5V Output Saturation Voltage -IN=1V, +IN=0V VOL 25°C - 250 400 mV (Low Level Output Voltage) ISINK=4mA -IN=0V, +IN=1V 25°C - 0.1 - nA Output Leakage Current OUT=5V ILEAK (High Level Output Current) -IN=0V, +IN=1V 25°C - - 1 μA OUT=36V RL=5.1kΩ, VRL=5V - 1.3 - IN=100mVP-P, Overdrive=5mV Response Time tRE 25°C μs RL=5.1kΩ, VRL=5V, IN=TTL - 0.4 - Logic Swing, VREF=1.4V (Note 23) Absolute value (Note 24) Current Direction: Because the first stage is composed with PNP transistor, input bias current flows out of IC. (Note 25) Please determine the output current value in consideration of the power dissipation of the IC under high temperature environment. When the output terminal is continuously shorted, output current may be reduced by the temperature rise of the IC. ○BA10339 xx(Unless otherwise specified VCC=+5V, VEE=0V, TA=25°C) Temperature Limit Parameter Symbol Unit Conditions Range Min Typ Max Input Offset Voltage (Note 26) VIO 25°C - 1 5 mV OUT=1.4V Input Offset Current (Note 26) IIO 25°C - 5 50 nA OUT=1.4V Input Bias Current (Note 27) IB 25°C - 50 250 nA OUT=1.4V Input Common-mode VCC VICM 25°C 0 - V - Voltage Range -1.5 50 200 - V/mV VCC=15V, OUT=1.4 ~ 11.4V Large Signal Voltage Gain AV 25°C 94 106 - dB RL=15kΩ, VRL=15V Supply Current ICC 25°C - 0.8 2 mA RL=∞, All Comparators -IN=1V, +IN=0V Output Sink Current(Note 28) ISINK 25°C 6 16 - mA OUT=1.5V Output Saturation Voltage -IN=1V, +IN=0V VOL 25°C - 250 400 mV (Low Level Output Voltage) ISINK=4mA -IN=0V, +IN=1V 25°C - 0.1 - nA Output Leakage Current OUT=5V ILEAK (High Level Output Current) -IN=0V, +IN=1V 25°C - - 1 μA OUT=36V RL=5.1kΩ, VRL=5V - 1.3 - IN=100mVP-P, Overdrive=5mV Response Time tRE 25°C μs RL=5.1kΩ, VRL=5V, IN=TTL - 0.4 - Logic Swing, VREF=1.4V (Note 26) Absolute value (Note 27) Current Direction: Because the first stage is composed with PNP transistor, input bias current flows out of IC. (Note 28) Please determine the output current value in consideration of the power dissipation of the IC under high temperature environment. When the output terminal is continuously shorted, output current may be reduced by the temperature rise of the IC. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 7/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Electrical Characteristics - continued ○BA2903xxx, BA2903S xxx(Unless otherwise specified VCC=+5V, VEE=0V, TA=25°C) Temperature Limit Parameter Symbol Unit Conditions Range Min Typ Max 25°C - 2 7 OUT=1.4V Input Offset Voltage (Note 29,30) VIO mV Full range - - 15 VCC=5 to 36V, OUT=1.4V 25°C - 5 50 Input Offset Current (Note 29,30) IIO nA OUT=1.4V Full range - - 200 25°C - 50 250 Input Bias Current (Note 30,31) IB nA OUT=1.4V Full range - - 500 Input Common-mode VCC VICM 25°C 0 - V - Voltage Range -1.5 25 100 - V/mV VCC=15V, OUT=1.4 to 11.4V Large Signal Voltage Gain AV 25°C 88 100 - dB RL=15kΩ, VRL=15V 25°C - 0.6 1 OUT=Open Supply Current (Note 30) ICC mA Full range - - 2.5 OUT=Open, VCC=36V +IN=0V, -IN=1V Output Sink Current(Note 32) ISINK 25°C 6 16 - mA OUT=1.5V Output Saturation Voltage(Note 30) 25°C - 150 400 +IN=0V, -IN= 1V VOL mV (Low Level Output Voltage) Full range - - 700 ISINK=4mA +IN=1V, -IN=0V 25°C - 0.1 - nA Output Leakage Current (Note 30) OUT=5V ILEAK (High Level Output Current) +IN=1V, -IN=0V Full range - - 1 μA OUT=36V RL=5.1kΩ, VRL=5V - 1.3 - IN=100mVP-P, Overdrive=5mV Response Time tRE 25°C μs RL=5.1kΩ, VRL=5V, IN=TTL - 0.4 - Logic Swing, VREF=1.4V (Note 29) Absolute value (Note 30) BA2903S : Full range -40°C to +105°C, BA2903: Full range -40°C to +125°C (Note 31) Current Direction: Because the first stage is composed with PNP transistor, input bias current flows out of IC. (Note 32) Please determine the output current value in consideration of the power dissipation of the IC under high temperature environment. When the output terminal is continuously shorted, output current may be reduced by the temperature rise of the IC. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 8/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Electrical Characteristics - continued ○BA2903Wxx (Unless otherwise specified VCC=+5V, VEE=0V, TA=25°C) Temperature Limit Parameter Symbol Unit Conditions Range Min Typ Max Input Offset Voltage (Note 33) VIO 25°C - 0.5 2 mV OUT=1.4V Input Offset Current (Note 33) IIO 25°C - 5 50 nA OUT=1.4V 25°C - 50 250 Input Bias Current (Note 34,35) IB nA OUT=1.4V Full range - - 500 Input Common-mode VCC VICM 25°C 0 - V - Voltage Range -1.5 25 100 - V/mV VCC=15V, OUT=1.4 to 11.4V Large Signal Voltage Gain AV 25°C 88 100 - dB RL=15kΩ, VRL=15V 25°C - 0.6 1 OUT=Open Supply Current (Note 34) ICC mA Full range - - 2.5 OUT=Open, VCC=36V +IN=0V, -IN=1V Output Sink Current (Note 36) ISINK 25°C 6 16 - mA OUT=1.5V Output Saturation Voltage(Note 34) 25°C - 150 400 +IN=0V, -IN= 1V VOL mV (Low Level Output Voltage) Full range - - 700 ISINK=4mA +IN=1V, -IN=0V 25°C - 0.1 - nA Output Leakage Current (Note 34) OUT=5V ILEAK (High Level Output Current) +IN=1V, -IN=0V Full range - - 1 μA OUT=36V RL=5.1kΩ, VRL=5V - 1.3 - IN=100mVP-P, Overdrive=5mV Response Time tRE 25°C μs RL=5.1kΩ, VRL=5V, IN=TTL - 0.4 - Logic Swing, VREF=1.4V (Note 33) Absolute value (Note 34) BA2903W: Full range -40°C to +125°C (Note 35) Current Direction: Because the first stage is composed with PNP transistor, input bias current flows out of IC. (Note 36) Please determine the output current value in consideration of the power dissipation of the IC under high temperature environment. When the output terminal is continuously shorted, output current may be reduced by the temperature rise of the IC. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 9/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Electrical Characteristics - continued ○BA2901xx, BA2901S xx(Unless otherwise specified VCC=+5V, VEE=0V, Ta=25°C) Limit Temperature Parameter Symbol Unit Conditions Range Min Typ Max 25°C - 2 7 OUT=1.4V Input Offset Voltage (Note 37,38) VIO mV Full range - - 15 VCC=5 to 36V, OUT=1.4V 25°C - 5 50 Input Offset Current (Note 37,38) IIO nA OUT=1.4V Full range - - 200 25°C - 50 250 Input Bias Current (Note 38,39) IB nA OUT=1.4V Full range - - 500 Input Common-mode VICM 25°C 0 - VCC-1.5 V - Voltage Range 25 100 - V/mV VCC=15V, OUT=1.4 to 11.4V Large Signal Voltage Gain AV 25°C 88 100 - dB RL=15kΩ, VRL=15V 25°C - 0.8 2 OUT=Open Supply Current (Note 38) ICC mA Full range - - 2.5 OUT=Open, VCC=36V Output Sink Current(Note 40) ISINK 25°C 6 16 - mA +IN=0V, VIN=1V OUT=1.5V Output Saturation Voltage(Note 38) 25°C - 150 400 +IN=0V, -IN=1V VOL mV (Low Level Output Voltage) Full range - - 700 ISINK=4mA +IN=1V, -IN=0V 25°C - 0.1 - nA Output Leakage Current (Note 38) OUT=5V ILEAK (High Level Output Current) +IN=1V, -IN=0V Full range - - 1 μA OUT=36V RL=5.1kΩ, VRL=5V - 1.3 - VIN=100mVP-P, Overdrive=5mV Response Time tRE 25°C μs RL=5.1kΩ, VRL=5V, VIN=TTL - 0.4 - Logic Swing, VREF=1.4V (Note 37) Absolute value (Note 38) BA2901S：Full range -40°C to 105°C ,BA2901：Full range -40°C to +125°C (Note 39) Current Direction : Because the first stage is composed with PNP transistor, input bias current flows out of IC. (Note 40) Please determine the output current value in consideration of the power dissipation of the IC under high temperature environment. When the output terminal is continuously shorted, output current may be reduced by the temperature rise of the IC. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 10/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Description of electrical characteristics Described below are descriptions of the relevant electrical terms used in this datasheet. Items and symbols used are also shown. Note that item name and symbol and their meaning may differ from those on another manufacturer’s document or general document. 1. Absolute maximum ratings Absolute maximum rating items indicate the condition which must not be exceeded. Application of voltage in excess of absolute maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of characteristics. (1) Power supply voltage (VCC/VEE) Indicates the maximum voltage that can be applied between the positive power supply terminal and negative power supply terminal without deterioration or destruction of characteristics of internal circuit. (2) Differential input voltage (VID) Indicates the maximum voltage that can be applied between non-inverting and inverting terminals without damaging the IC. (3) Input common-mode voltage range (VICM) Indicates the maximum voltage that can be applied to the non-inverting and inverting terminals without deterioration or destruction of electrical characteristics. Input common-mode voltage range of the maximum ratings does not assure normal operation of IC. For normal operation, use the IC within the input common-mode voltage range characteristics. (4) Power dissipation (Pd) Indicates the power that can be consumed by the IC when mounted on a specific board at the ambient temperature 25°C (normal temperature). As for package product, Pd is determined by the temperature that can be permitted by the IC in the package (maximum junction temperature) and the thermal resistance of the package. 2. Electrical characteristics (1) Input offset voltage (VIO) Indicates the voltage difference between non-inverting terminal and inverting terminals. It can be translated into the input voltage difference required for setting the output voltage at 0 V. (2) Input offset current (IIO) Indicates the difference of input bias current between the non-inverting and inverting terminals. (3) Input bias current (IB) Indicates the current that flows into or out of the input terminal. It is defined by the average of input bias currents at the non-inverting and inverting terminals. (4) Input common-mode voltage range (VICM) Indicates the input voltage range where IC normally operates. (5) Large signal voltage gain (AV) Indicates the amplifying rate (gain) of output voltage against the voltage difference between non-inverting terminal and inverting terminal. It is normally the amplifying rate (gain) with reference to DC voltage. Av = (Output voltage) / (Differential Input voltage) (6) Supply current (ICC) Indicates the current that flows within the IC under specified no-load conditions. (7) Output sink current (ISINK) Denotes the maximum current that can be output under specific output conditions. (8) Output saturation voltage, low level output voltage (VOL) Signifies the voltage range that can be output under specific output conditions. (9) Output leakage current, High level output current (ILEAK) Indicates the current that flows into the IC under specific input and output conditions. (10) Response time (tRE) Response time indicates the delay time between the input and output signal is determined by the time difference from the fifty percent of input signal swing to the fifty percent of output signal swing. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 11/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves ○BA8391G 0.8 0.8 0.7 0.6 0.6 BA8391G n [W] mA]0.5 -40℃ atio ent [ sip 0.4 urr0.4 25℃ s C er Di ply 0.3 Pow 0.2 Sup0.2 85℃ 0.1 0 0.0 85 0 25 50 75 100 125 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 2. Figure 3. Power Dissipation vs Ambient Temperature Supply Current vs Supply Voltage (Derating Curve) 0.8 200 0.7 V] 0.6 m150 A] ge [ urrent [m 00..45 36V on Volta100 85℃ upply C 0.3 5V Saturati 25℃ S ut 0.2 2V Outp 50 -40℃ 0.1 0 0 -50 -25 0 25 50 75 100 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 4. Figure 5. Supply Current vs Ambient Temperature Output Saturation Voltage vs Supply Voltage (IOL=4mA) (*)The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 12/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA8391G 200 2.0 1.8 e [mV] . 150 ge [V]11..46 g a olta Volt1.2 uration V 100 2V aturation 01..80 85℃ 25℃ at S ut S 36V 5V put 0.6 utp 50 Out O 0.4 -40℃ 0.2 0 0.0 -50 -25 0 25 50 75 100 0 2 4 6 8 10 12 14 16 18 20 Ambient Temperature [°C] Output Sink Current [mA] Figure 6. Figure 7. Output Saturation Voltage vs Ambient Temperature Output Saturation Voltage vs ( IOL=4mA) Output Sink Current (VCC=5V) 40 8 6 A]30 V]4 m m Current [20 36V 5V Voltage [02 -40℃ 25℃ nk et 85℃ utput Si 2V put Offs-2 O10 In-4 -6 0 -8 -50 -25 0 25 50 75 100 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 8. Figure 9. Output Sink Current vs Ambient Temperature Input Offset Voltage vs Supply Voltage (OUT=1.5V) (*)The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 13/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA8391G 8 160 6 140 mV]4 A]120 ge [2 2V nt [n100 a e olt urr -40℃ 25℃ V0 C 80 et 5V 36V s s a ut Off-2 put Bi 60 p n n I 85℃ I-4 40 -6 20 -8 0 -50 -25 0 25 50 75 100 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 10. Figure 11. Input Offset Voltage vs Ambient Temperature Input Bias Current vs Supply Voltage 160 50 40 140 30 120 rrent [nA] 100 36V urrent [nA]1200 -40℃ 25℃ u C s C 80 et 0 Input Bia 4600 5V Input Offs--2100 85℃ 2V -30 20 -40 0 -50 -50 -25 0 25 50 75 100 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 12. Figure 13. Input Bias Current vs Ambient Temperature Input Offset Current vs Supply Voltage (*)The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 14/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA8391G 50 140 40 130 30 B] d 120 85℃ ent [nA] 1200 2V e Gain [ 110 ut Offset Curr -100 5V 36V Signal Voltag 19000 25℃ -40℃ np -20 e I rg 80 a -30 L 70 -40 -50 60 -50 -25 0 25 50 75 100 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 14. Figure 15. Input Offset Current vs Ambient Temperature Large Signal Voltage Gain vs Supply Voltage 140 160 130 B] 140 dB] 120 36V o [d n [ ati ai R120 G 110 n 85℃ age 5V ectio olt 100 2V ej100 V R al de 25℃ -40℃ gn 90 Mo e Si on 80 rg 80 m La m o C 60 70 60 40 -50 -25 0 25 50 75 100 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 16. Figure 17. Large Signal Voltage Gain vs Ambient Common Mode Rejection Ratio Temperature vs Supply Voltage (*)The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 15/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA8391G 150 6 B] 125 4 d 36V 25℃ o [ on Rati 100 ge [mV] 2 -40℃ 85℃ ecti olat ej 75 2V 5V V 0 e R set od Off mon M 50 Input -2 m Co 25 -4 0 -6 -50 -25 0 25 50 75 100 -1 0 1 2 3 4 5 Ambient Temperature [°C] Input Voltage [V] Figure 18. Figure 19. Common Mode Rejection Ratio vs Ambient Input Offset Voltage - Input Voltage Temperature (VCC=5V) 200 5 180 dB] μs]4 Ratio [ 160 High) [ n o ejectio 140 (Low t3 R e y 120 m pl Ti2 ower Sup 100 esponse 1 85℃ 25℃ -40℃ P R 80 60 0 -50 -25 0 25 50 75 100 -100 -80 -60 -40 -20 0 Ambient Temperature [°C] Over Drive Voltage [mV] Figure 20. Figure 21. Power Supply Rejection Ratio vs Ambient Response Time (Low to High) Temperature vs Over Drive Voltage (VCC=5V, VRL=5V, RL=5.1kΩ) (*)The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 16/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA8391G 5 5 μs] 4 μs]4 h) [ w) [ g o me (Low to Hi3 me (High to L3 Ti2 5mV overdrive Ti2 e e s s on 20mV overdrive on 85℃ sp sp 25℃ Re1 Re1 -40℃ 100mV overdrive 0 0 -50 -25 0 25 50 75 100 0 20 40 60 80 100 Ambient Temperature [°C] Output Drive Voltage [mV] Figure 22. Figure 23. Response Time (Low to High) Response Time (High to Low) vs Ambient Temperature vs Over Drive Voltage (VCC=5V, VRL=5V, RL=5.1kΩ) (VCC=5V, VRL=5V, RL=5.1kΩ) 5 w) [μs] 4 o L o h t3 g Hi ( e m 5mV overdrive Ti2 e s n o 20mV overdrive p es1 R 100mV overdrive 0 -50 -25 0 25 50 75 100 Ambient Temperature [°C] Figure 24. Response Time (High to Low) vs Ambient Temperature (VCC=5V, VRL=5V, RL=5.1kΩ) (*)The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 17/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA10393F 1.0 1.0 0.8 0.8 -40℃ W] . mA] on [0.6 nt [ 0.6 25℃ ati BA10393F re p ur wer Dissi0.4 upply C 0.4 o S 85℃ P 0.2 0.2 0.0 0.0 85 0 25 50 75 100 125 0 10 20 30 40 Ambient Temperature [°C] . Supply Voltage [V] Figure 25. Figure 26. Power Dissipation vs Ambient Temperature Supply Current vs Supply Voltage (Derating Curve) 1.0 500 85℃ 0.8 V]400 m A] 36V ge [ m a 25℃ nt [0.6 Volt300 Curre 5V ation pply 0.4 Satur200 -40℃ Su ut 2V p ut 0.2 O100 0.0 0 -50 -25 0 25 50 75 100 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 27. Figure 28. Supply Current vs Ambient Temperature Output Saturation Voltage vs Supply Voltage (IOL=4mA) (*)The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 18/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA10393F 500 2.0 1.8 mV]400 V]1.6 e [ ge [1.4 oltag300 2V Volta1.2 n V on 25℃ ut Saturatio200 36V 5V put Saturati001...680 85℃ utp Out O100 0.4 -40℃ 0.2 0 0.0 -50 -25 0 25 50 75 100 0 2 4 6 8 10 12 14 16 18 20 Ambient Temperature [°C] Output Sink Current [mA] Figure 29. Figure 30. Output Saturation Voltage vs Ambient Temperature Output Saturation Voltage vs ( IOL=4mA) Output Sink Current (VCC=5V) 40 8 6 A]30 V]4 m m Current [20 36V 5V Voltage [02 -40℃ 25℃ nk et utput Si 2V put Offs-2 85℃ O10 In-4 -6 0 -8 -50 -25 0 25 50 75 100 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 31. Figure 32. Output Sink Current vs Ambient Temperature Input Offset Voltage vs Supply Voltage (OUT=1.5V) (*)The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 19/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA10393F 8 160 6 140 V] 4 120 m A] Voltage [ 02 2V 5V Current [n18000 -40℃ 25℃ set as ut Off-2 36V put Bi 60 p n n I 85℃ I-4 40 -6 20 -8 0 -50 -25 0 25 50 75 100 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 33. Figure 34. Input Offset Voltage vs Ambient Temperature Input Bias Current vs Supply Voltage 160 50 40 140 30 120 nt [nA] 100 36V ent [nA]1200 -40℃ rre urr Cu 80 C 0 25℃ nput Bias 60 5V put Offset --2100 85℃ I 40 In 2V -30 20 -40 0 -50 -50 -25 0 25 50 75 100 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 35. Figure 36. Input Bias Current vs Ambient Temperature Input Offset Current vs Supply Voltage (*)The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 20/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA10393F 50 140 40 130 30 B] 25℃ 36V d 120 nt [nA] 20 Gain [ 110 e 10 e urr 5V ag 85℃ -40℃ Offset C -100 2V nal Volt 100 ut Sig 90 np -20 e I rg 80 a -30 L 70 -40 -50 60 -50 -25 0 25 50 75 100 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 37. Figure 38. Input Offset Current vs Ambient Temperature Large Signal Voltage Gain vs Supply Voltage 140 160 130 B] 140 n [dB] 120 36V atio [d ai R 120 e G 110 on oltag 100 2V 5V ejecti 100 -40℃ 25℃ V R nal de e Sig 90 n Mo 80 85℃ arg 80 mo L m o C 60 70 60 40 -50 -25 0 25 50 75 100 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 39. Figure 40. Large Signal Voltage Gain vs Ambient Common Mode Rejection Ratio Temperature vs Supply Voltage (*)The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 21/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA10393F 140 140 dB] 130 B] 130 Ratio [ 120 atio [d 120 ection 110 36V 5V ction R 110 Rej 100 eje 100 R ode 90 ply 90 M up mmon 80 2V wer S 80 Co Po 70 70 60 60 -50 -25 0 25 50 75 100 -50 -25 0 25 50 75 100 Ambient Temperature [°C] Ambient Temperature [°C] Figure 41. Figure 42. Common Mode Rejection Ratio vs Ambient Power Supply Rejection Ratio vs Ambient Temperature Temperature 5 5 μs] 4 μs] 4 h) [ w) [ Hig Lo w to 3 gh to 3 Lo Hi e ( e ( m 5mV overdrive m Ti 2 Ti 2 e e ns ns 5mV overdrive o 20mV overdrive o esp 1 esp 1 20mV overdrive 100mV overdrive R R 100mV overdrive 0 0 -50 -25 0 25 50 75 100 -50 -25 0 25 50 75 100 Ambient Temperature [°C] Ambient Temperature [°C] Figure 43. Figure 44. Response Time (Low to High) vs Ambient Response Time (High to Low) vs Ambient Temperature Temperature (VCC=5V, VRL=5V, RL=5.1kΩ) (VCC=5V, VRL=5V, RL=5.1kΩ) (*)The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 22/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA10339xx 1.0 1.0 -40℃ 0.8 0.8 W] . mA] 25℃ n [0.6 B A10339FV nt [0.6 patio Curre Dissi0.4 ply 0.4 wer BA10339F Sup 85℃ o P 0.2 0.2 0.0 0.0 85 0 10 20 30 40 0 25 50 75 100 125 Supply Voltage [V] Ambient Temperature [°C] Figure 45. Figure 46. Power Dissipation vs Ambient Temperature Supply Current vs Supply Voltage (Derating Curve) 1 500 0.8 V]400 A] 36V ge [m 85℃ m 5V a nt [0.6 Volt300 Curre ation 25℃ Supply 0.4 2V ut Satur200 p 0.2 Out100 -40℃ 0 0 -50 -25 0 25 50 75 100 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 47. Figure 48. Supply Current vs Ambient Temperature Output Saturation Voltage vs Supply Voltage (IOL=4mA) (*)The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 23/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA10339xx 500 2.0 1.8 mV]400 V]1.6 ration Voltage [300 2V uration Voltage [111...024 85℃ Output Satu120000 36V 5V Output Sat000...468 -40℃ 25℃ 0.2 0 0.0 -50 -25 0 25 50 75 100 0 2 4 6 8 10 12 14 16 18 20 Ambient Temperature [°C] Output Sink Current [mA] Figure 49. Figure 50. Output Saturation Voltage vs Ambient Temperature Output Saturation Voltage vs ( IOL=4mA) Output Sink Current (VCC=5V) 40 8 6 A]30 V] 4 m m nt [ ge [ 2 urre olta C20 V 0 utput Sink 36V 5V put Offset -2 -40℃ 25℃ O10 In-4 3V 85℃ -6 0 -8 -50 -25 0 25 50 75 100 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 51. Figure 52. Output Sink Current vs Ambient Temperature Input Offset Voltage vs Supply Voltage (OUT=1.5V) (*)The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 24/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA10339xx 8 50 6 40 V] 4 m A] ge [ 2 nt [n30 a e Volt 0 Curr -40℃ 25℃ et s s a ut Off-2 36V 5V put Bi20 p n In-4 I 85℃ 3V 10 -6 -8 0 0 10 20 30 40 0 10 20 30 40 Supply Voltage [V] Supply Voltage [V] Figure 53. Figure 54. Input Offset Voltage vs Ambient Temperature Input Bias Current vs Supply Voltage 50 50 40 40 30 nt [nA] 30 36V ent [nA] 1200 85℃ e r rr ur u C C 0 Bias 20 Offset -10 -40℃ 25℃ nput 5V put -20 I In 10 -30 -40 3V 0 -50 -50 -25 0 25 50 75 100 0 10 20 30 40 Supply Voltage [V] Ambient Temperature [°C] Figure 55. Figure 56. Input Bias Current vs Ambient Temperature Input Offset Current vs Supply Voltage (*)The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 25/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA10339xx 50 140 40 130 30 B] d120 nt [nA] 20 36V 5V Gain [110 85℃ 25℃ e 10 e urr ag ut Offset C-100 3V Signal Volt19000 -40℃ np-20 e I rg 80 a -30 L 70 -40 -50 60 -50 -25 0 25 50 75 100 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 57. Figure 58. Input Offset Current vs Ambient Temperature Large Signal Voltage Gain vs Supply Voltage 140 160 130 B]140 dB] 120 o [d n [ ati ge Gai 110 36V ction R120 -40℃ 25℃ a e al Volt 100 5V de Rej100 gn 90 3V Mo 85℃ e Si on 80 rg 80 m La om C 60 70 60 40 -50 -25 0 25 50 75 100 0 10 20 30 40 Supply Voltage [V] Ambient Temperature [°C] Figure 59. Figure 60. Large Signal Voltage Gain vs Ambient Common Mode Rejection Ratio Temperature vs Supply Voltage (*)The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 26/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA10339xx 150 140 130 dB] 125 B] ection Ratio [ 100 36V 5V ction Ratio [d111200 Rej 75 3V eje100 ode ply R 90 n M 50 Sup mmo wer 80 Co 25 Po 70 0 60 -50 -25 0 25 50 75 100 -50 -25 0 25 50 75 100 Ambient Temperature [°C] Ambient Temperature [°C] Figure 61. Figure 62. Common Mode Rejection Ratio vs Ambient Power Supply Rejection Ratio vs Ambient Temperature Temperature 5 5 h) [μs]4 w) [μs] 4 Hig Lo o o w t3 h t3 Lo Hig e ( 5mV overdrive e ( m m Ti2 Ti2 nse nse 5mV overdrive 100mV overdrive po 20mV overdrive po 20mV overdrive es1 es1 R R 100mV overdrive 0 0 -50 -25 0 25 50 75 100 -50 -25 0 25 50 75 100 Ambient Temperature [°C] Ambient Temperature [°C] Figure 63. Figure 64. Response Time (Low to High) vs Ambient Response Time (High to Low) vs Ambient Temperature Temperature (VCC=5V, VRL=5V, RL=5.1kΩ) (VCC=5V, VRL=5V, RL=5.1kΩ) (*)The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 27/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA2903xxx, BA2903Sxxx, BA2903Wxx 1.0 1.6 1.4 0.8 W] . BB AA22990033FS F mA]1.2 1.0 pation [ 0.6 BBAA22990033FSVF V urrent [0.8 -40℃ 25℃ er Dissi 0.4 upply C0.6 w S o BA2903FVM P BA2903SFVM 0.4 0.2 0.2 105℃ 125℃ 0.0 0.0 105 0 25 50 75 100 125 150 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 65. Figure 66. Power Dissipation vs Ambient Temperature Supply Current vs Supply Voltage (Derating Curve) (Refer to the following operating temperature) 1.6 200 1.4 V] 1.2 m150 nt [mA]1.0 Voltage [ 125℃ 105℃ urre0.8 on 100 C 36V ati 25℃ upply 0.6 5V Satur S ut 0.4 Outp 50 -40℃ 2V 0.2 0.0 0 -50 -25 0 25 50 75 100 125 150 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 67. Figure 68. Supply Current vs Ambient Temperature Output Saturation Voltage vs Supply Voltage (IOL=4mA) (*)The above characteristics are measurements of typical sample, they are not guaranteed. BA2903：-40°C to ＋125°C BA2903S：-40°C to ＋105°C BA2903W：-40°C to ＋125°C www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 28/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA2903xxx, BA2903Sxxx, BA2903Wxx 200 2.0 1.8 mV]150 V] 1.6 e [ ge [ 1.4 n Voltag 2V on Volta 1.2 125℃ 25℃ atio100 rati 1.0 r u atu 5V Sat 0.8 105℃ ut S 36V put 0.6 utp 50 Out -40℃ O 0.4 0.2 0 0.0 -50 -25 0 25 50 75 100 125 150 0 2 4 6 8 10 12 14 16 18 20 Ambient Temperature [°C] Output Sink Current [mA] Figure 69. Figure 70. Output Saturation Voltage vs Ambient Temperature Output Saturation Voltage vs ( IOL=4mA) Output Sink Current (VCC=5V) 40 8 6 A]30 V] 4 m m urrent [ 5V 36V oltage [ 2 -40℃ C20 V 0 nk et 25℃ 105℃ 125℃ utput Si 2V put Offs-2 O10 In-4 -6 0 -8 -50 -25 0 25 50 75 100 125 150 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 71. Figure 72. Output Sink Current vs Ambient Temperature Input Offset Voltage vs Supply Voltage (OUT=1.5V) (*)The above characteristics are measurements of typical sample, they are not guaranteed. BA2903：-40°C to ＋125°C BA2903S：-40°C to ＋105°C BA2903W：-40°C to ＋125°C www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 29/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA2903xxx, BA2903Sxxx, BA2903Wxx 8 160 6 140 V]4 120 m A] age [2 2V ent [n100 -40℃ set Volt0 5V 36V as Curr 80 ut Off-2 put Bi 60 25℃ np In I-4 40 105℃ 125℃ -6 20 -8 0 -50 -25 0 25 50 75 100 125 150 0 5 10 15 20 25 30 35 Ambient Temperature [°C] Supply Voltage [V] Figure 73. Figure 74. Input Offset Voltage vs Ambient Temperature Input Bias Current vs Supply Voltage 160 50 40 140 30 120 nt [nA] 100 ent [nA] 1200 urre 36V Curr -40℃ 25℃ s C 80 et 0 nput Bia 60 put Offs--2100 105℃ 125℃ I 40 In 5V -30 2V 20 -40 0 -50 -50 -25 0 25 50 75 100 125 150 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 75. Figure 76. Input Bias Current vs Ambient Temperature Input Offset Current vs Supply Voltage (*)The above characteristics are measurements of typical sample, they are not guaranteed. BA2903：-40°C to ＋125°C BA2903S：-40°C to ＋105°C BA2903W：-40°C to ＋125°C www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 30/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA2903xxx, BA2903Sxxx, BA2903Wxx 50 140 40 130 30 dB] 120 125℃ 105℃ ent [nA] 1200 2V e Gain [110 ut Offset Curr-100 5V 36V Signal Voltag19000 25℃ -40℃ Inp-20 rge 80 a -30 L 70 -40 -50 60 -50 -25 0 25 50 75 100 125 150 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 77. Figure 78. Input Offset Current vs Ambient Temperature Large Signal Voltage Gain vs Supply Voltage 140 160 130 B]140 dB] 120 36V o [d n [ ati ai R120 Voltage G 110100 15V 5V Rejection 100 105℃ 125℃ al de gn 90 Mo -40℃ 25℃ e Si on 80 rg 80 m La om C 60 70 60 40 -50 -25 0 25 50 75 100 125 150 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 79. Figure 80. Large Signal Voltage Gain vs Ambient Common Mode Rejection Ratio Temperature vs Supply Voltage (*)The above characteristics are measurements of typical sample, they are not guaranteed. BA2903：-40°C to ＋125°C BA2903S：-40°C to ＋105°C BA2903W：-40°C to ＋125°C www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 31/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA2903xxx, BA2903Sxxx, BA2903Wxx 150 6 B] 125 4 d 25℃ n Ratio [100 36V e [mV] 2 -40℃ 105℃ ectio oltag 125℃ e Rej 75 5V 2V set V 0 od Off mmon M 50 Input -2 o C 25 -4 0 -6 -50 -25 0 25 50 75 100 125 150 -1 0 1 2 3 4 5 Ambient Temperature [°C] Input Voltage [V] Figure 81. Figure 82. Common Mode Rejection Ratio vs Ambient Input Offset Voltage - Input Voltage Temperature (VCC=5V) 200 5 Ratio [dB] 116800 High) [μs]4 n o ejectio140 (Low t3 R e ply 120 Tim2 wer Sup100 sponse 125℃ 105℃ 25℃ -40℃ o e1 P R 80 60 0 -50 -25 0 25 50 75 100 125 150 -100 -80 -60 -40 -20 0 Ambient Temperature [°C] Over Drive Voltage [V] Figure 83. Figure 84. Power Supply Rejection Ratio vs Ambient Response Time (Low to High) Temperature vs Over Drive Voltage (VCC=5V, VRL=5V, RL=5.1kΩ) (*)The above characteristics are measurements of typical sample, they are not guaranteed. BA2903：-40°C to ＋125°C BA2903S：-40°C to ＋105°C BA2903W：-40°C to ＋125°C www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 32/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA2903xxx, BA2903Sxxx, BA2903Wxx 5 5 μs]4 μs] 4 h) [ w) [ Hig Lo o o w t3 h t3 me (Lo me (Hig 125℃ 105℃ Ti2 5mV overdrive Ti2 se 20mV overdrive se 25℃ on on -40℃ sp 100mV overdrive sp Re1 Re1 0 0 -50 -25 0 25 50 75 100 125 150 0 20 40 60 80 100 Ambient Temperature [°C] Over Drive Voltage [V] Figure 85. Figure 86. Response Time (Low to High) Response Time (High to Low) vs Ambient Temperature vs Over Drive Voltage (VCC=5V, VRL=5V, RL=5.1kΩ) (VCC=5V, VRL=5V, RL=5.1kΩ) 5 s] 4 μ w) [ Lo o h t3 g Hi 5mV overdrive e ( m e Ti2 20mV overdrive s n o 100mV overdrive p es1 R 0 -50 -25 0 25 50 75 100 125 150 Ambient Temperature [°C] Figure 87. Response Time (High to Low) vs Ambient Temperature (VCC=5V, VRL=5V, RL=5.1kΩ) (*)The above characteristics are measurements of typical sample, they are not guaranteed. BA2903：-40°C to ＋125°C BA2903S：-40°C to ＋105°C BA2903W：-40°C to ＋125°C www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 33/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA2901xx, BA2901Sxx 1.0 2.0 1.8 0.8 1.6 BA2901FV BA2901SFV -40℃ W] A]1.4 n [ m 25℃ sipatio 0.6 BB AA22990011FS F urrent [11..02 er Dis 0.4 ply C0.8 w up o S P 0.6 0.2 0.4 105℃ 125℃ 0.2 0.0 105 0.0 0 25 50 75 100 125 150 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 88. Figure 89. Power Dissipation vs Ambient Temperature Supply Current vs Supply Voltage (Derating Curve) (Refer to the following operating temperature) 2.0 200 1.8 1.6 V] m150 nt [mA]11..24 36V Voltage [ 125℃ 105℃ Curre1.0 5V ation 100 25℃ y ur ppl0.8 Sat Su0.6 ut 2V utp 50 0.4 O -40℃ 0.2 0.0 0 -50 -25 0 25 50 75 100 125 150 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 90. Figure 91. Supply Current vs Ambient Temperature Output Saturation Voltage vs Supply Voltage (IOL=4mA) (*)The above characteristics are measurements of typical sample, they are not guaranteed. BA2901：-40°C to ＋125°C BA2901S：-40°C to ＋105°C www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 34/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA2901xx, BA2901Sxx 200 2.0 1.8 mV]150 V] 1.6 oltage [ Voltage [ 11..24 125℃ n V 2V on 25℃ atio100 rati 1.0 r u ut Satu 36V 5V put Sat 00..68 105℃ utp 50 Out -40℃ O 0.4 0.2 0 0.0 -50 -25 0 25 50 75 100 125 150 0 2 4 6 8 10 12 14 16 18 20 Ambient Temperature [°C] Output Sink Current [mA] Figure 92. Figure 93. Output Saturation Voltage vs Ambient Temperature Output Saturation Voltage vs ( IOL=4mA) Output Sink Current (VCC=5V) 40 8 6 A]30 V] 4 m m urrent [ 5V 36V oltage [ 2 -40℃ C20 V 0 nk et 25℃ 105℃ 125℃ utput Si 2V put Offs-2 O10 In-4 -6 0 -8 -50 -25 0 25 50 75 100 125 150 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 94. Figure 95. Output Sink Current vs Ambient Temperature Input Offset Voltage vs Supply Voltage (OUT=1.5V) (*)The above characteristics are measurements of typical sample, they are not guaranteed. BA2901：-40°C to ＋125°C BA2901S：-40°C to ＋105°C www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 35/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA2901xx, BA2901Sxx 8 160 6 140 V]4 120 m A] age [2 2V ent [n100 -40℃ Volt0 Curr 80 et 5V 36V s s a ut Off-2 put Bi 60 25℃ p n In-4 I 40 105℃ 125℃ -6 20 -8 0 -50 -25 0 25 50 75 100 125 150 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 96. Figure 97. Input Offset Voltage vs Ambient Temperature Input Bias Current vs Supply Voltage 160 50 40 140 30 120 ent [nA] 100 rent [nA] 1200 -40℃ 25℃ urr 36V Cur s C 80 et 0 put Bia 60 ut Offs-10 105℃ 125℃ n p-20 I 40 In 5V -30 2V 20 -40 0 -50 -50 -25 0 25 50 75 100 125 150 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 98. Figure 99. Input Bias Current vs Ambient Temperature Input Offset Current vs Supply Voltage (*)The above characteristics are measurements of typical sample, they are not guaranteed. BA2901：-40°C to ＋125°C BA2901S：-40°C to ＋105°C www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 36/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA2901xx, BA2901Sxx 50 140 40 130 30 dB] 120 125℃ 105℃ nt [nA] 20 Gain [110 urre 10 2V age ut Offset C-100 5V 36V Signal Volt19000 25℃ -40℃ Inp-20 rge 80 a -30 L 70 -40 -50 60 -50 -25 0 25 50 75 100 125 150 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 100. Figure 101. Input Offset Current vs Ambient Temperature Large Signal Voltage Gain vs Supply Voltage 140 160 130 B]140 dB] 120 36V o [d n [ ati ai R120 Voltage G 110100 15V 5V Rejection 100 105℃ 125℃ al de gn 90 Mo -40℃ 25℃ e Si on 80 rg 80 m La om C 60 70 60 40 -50 -25 0 25 50 75 100 125 150 0 10 20 30 40 Ambient Temperature [°C] Supply Voltage [V] Figure 102. Figure 103. Large Signal Voltage Gain vs Ambient Common Mode Rejection Ratio Temperature vs Supply Voltage (*)The above characteristics are measurements of typical sample, they are not guaranteed. BA2901：-40°C to ＋125°C BA2901S：-40°C to ＋105°C www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 37/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA2901xx, BA2901Sxx 150 6 B] 125 4 d 25℃ o [ n Rati100 36V e [mV] 2 -40℃ 105℃ o g ecti olta 125℃ ej 75 V 0 e R 5V 2V set od Off mon M 50 Input -2 m o C 25 -4 0 -6 -50 -25 0 25 50 75 100 125 150 -1 0 1 2 3 4 5 Ambient Temperature [°C] Input Voltage [V] Figure 104. Figure 105. Common Mode Rejection Ratio vs Ambient Input Offset Voltage - Input Voltage Temperature (VCC=5V) 200 5 Ratio [dB] 116800 High) [μs]4 n o ejectio140 (Low t3 R e y 120 m pl Ti2 ower Sup100 esponse 1 125℃ 105℃ 25℃ -40℃ P R 80 60 0 -50 -25 0 25 50 75 100 125 150 -100 -80 -60 -40 -20 0 Ambient Temperature [°C] Over Drive Voltage [V] Figure 106. Figure 107. Power Supply Rejection Ratio vs Ambient Response Time (Low to High) Temperature vs Over Drive Voltage (VCC=5V, VRL=5V, RL=5.1kΩ) (*)The above characteristics are measurements of typical sample, they are not guaranteed. BA2901：-40°C to ＋125°C BA2901S：-40°C to ＋105°C www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 38/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Typical Performance Curves - continued ○BA2901xx, BA2901Sxx 5 5 μs]4 μs] 4 h) [ w) [ Hig Lo o o w t3 h t3 Time (Lo2 Time (Hig2 125℃ 105℃ se 5mV overdrive 20mV overdrive se 25℃ on on -40℃ sp 100mV overdrive sp Re1 Re1 0 0 -50 -25 0 25 50 75 100 125 150 0 20 40 60 80 100 Ambient Temperature [°C] Over Drive Voltage [V] Figure 108. Figure 109. Response Time (Low to High) Response Time (High to Low) vs Ambient Temperature vs Over Drive Voltage (VCC=5V, VRL=5V, RL=5.1kΩ) (VCC=5V, VRL=5V, RL=5.1kΩ) 5 s] 4 μ w) [ Lo o h t3 g Hi 5mV overdrive e ( m e Ti2 20mV overdrive s n 100mV overdrive o p es1 R 0 -50 -25 0 25 50 75 100 125 150 Ambient Temperature [°C] Figure 110. Response Time (High to Low) vs Ambient Temperature (VCC=5V, VRL=5V, RL=5.1kΩ) (*)The above characteristics are measurements of typical sample, they are not guaranteed. BA2901：-40°C to ＋125°C BA2901S：-40°C to ＋105°C www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 39/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Application Information NULL method condition for Test Circuit1 VCC, VEE, EK, VICM Unit : V, VRL=VCC BA10393 / BA10339 BA8391 / BA2903 / BA2901 Parameter VF S1 S2 S3 VCC VEE EK VICM VCC VEE EK VICM Calculation Input Offset Voltage VF1 ON ON ON 5 0 -1.4 0 5 to 36 0 -1.4 0 1 Input Offset Current VF2 OFF OFF ON 5 0 -1.4 0 5 0 -1.4 0 2 Input Bias Current VF3 OFF ON ON 5 0 -1.4 0 5 0 -1.4 0 3 VF4 ON OFF 5 0 -1.4 0 5 0 -1.4 0 Large Signal Voltage Gain VF5 ON ON ON 15 0 -1.4 0 15 0 -1.4 0 4 VF6 15 0 -11.4 0 15 0 -11.4 0 -1 .C Ianlpcuutl aOtifofsne -t Voltage (VIO) VIO = 1+|VRFF1|/ RS [V] |VF2-VF1| 2. Input Offset Current (IIO) IIO = RI ×(1+RF/RS) [A] |VF4-VF3| 3 . Input Bias Current (IB) IB = 2 × RI ×(1+RF/RS) [A] 4 . Large Signal Voltage Gain (AV) AV = 20Log ΔEK|V F×5 -(V1F+6R| F/RS) [dB] Rf=50kΩ 500kΩ 0.1μF SW1 VCC EK +15V Rs=50Ω 500kΩ Ri=10kΩ DUT Ri=10kΩ NULL SW3 Rs=50Ω 1000pF V VF Vicm RL SW2 VEE 50kΩ -15V Figure 111. Test Circuit1 (One Channel Only) www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 40/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Application Information - continued Switch Condition for Test Circuit 2 SW SW SW SW SW SW SW SW No. 1 2 3 4 5 6 7 Supply Current OFF OFF OFF OFF OFF OFF OFF Output Sink Current VOL=1.5V OFF ON ON OFF OFF OFF ON Saturation Voltage IOL=4mA OFF ON ON OFF ON ON OFF Output Leakage Current VOH=36V OFF ON ON OFF OFF OFF ON Response Time RL=5.1kΩ, VRL=5V ON OFF ON ON OFF OFF OFF VCC A － ＋ SW1 SW2 SW3 SW4 SW5 SW6 SW7 VEE RL V A -IN +IN OUT Figure 112. Test Circuit 2 (One Channel Only) IN Input wave IN Input wave VREF overdrive voltage overdrive voltage VREF OUT OUT Output wave Output wave VCC VCC VCC/2 VCC/2 0V 0V tRE(Low to High) tRE(High to Low) Figure 113. Response Time www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 41/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Power Dissipation Power dissipation (total loss) indicates the power that can be consumed by IC at TA=25°C (normal temperature).IC is heated when it consumed power, and the temperature of IC chip becomes higher than ambient temperature. The temperature that can be accepted by IC chip depends on circuit configuration, manufacturing process, and consumable power is limited. Power dissipation is determined by the temperature allowed in IC chip (maximum junction temperature) and thermal resistance of package (heat dissipation capability). The maximum junction temperature is typically equal to the maximum value in the storage temperature range. Heat generated by consumed power of IC radiates from the mold resin or lead frame of the package. The parameter which indicates this heat dissipation capability (hardness of heat release)is called thermal resistance, represented by the symbol θja °C/W.The temperature of IC inside the package can be estimated by this thermal resistance. Figure 114 (a) shows the model of thermal resistance of the package. Thermal resistance θja, ambient temperature TA, maximum junction temperature Tjmax, and power dissipation PD can be calculated by the equation below: θja = (Tjmax-TA) / PD °C/W ・・・・・ (Ⅰ) Derating curve in Figure 114 (b) indicates power that can be consumed by IC with reference to ambient temperature. Power that can be consumed by IC begins to attenuate at certain ambient temperature. This gradient is determined by thermal resistance θja. Thermal resistance θja depends on chip size, power consumption, package, ambient temperature, package condition, wind velocity, etc even when the same of package is used. Thermal reduction curve indicates a reference value measured at a specified condition. Figure 115 (c) to (g) shows a derating curve for an example of BA8391, BA10393, BA10339, BA2903S, BA2903, BA2903W, BA2901S, and BA2901. θja=(Tjmax-TA)/PD °C/W Powe rL SdIisのs消ipa費ti電on力 o f[ WL]SI [W] Pd (max) Ambien周t t囲em温p度er aTtau r[℃e ]TA [℃] P2 θja2 < θja1 θ' ja2 P1 θ ja2 Tj ' (max) Tj (max) Chip チsuッrプfa表ce面 te温m度p e Traj [t℃ur]e Tj [℃] θ' ja1 θ ja1 Powe消r 費di電ss力ipa Pti o[Wn ]PD [W] 0 25 50 75 100 125 150 Ambient 周te囲m温pe度ra Ttuar [e℃ T]a [℃] (a) Thermal Resistance (b) Derating curve Figure 114. Thermal Resistance and Derating Curve 1.0 1.0 1.0 0.8 0.8 0.8 W] W] W] BA10339FV (Note 43) wer Dissipation [00..46 BA8391G (Note 41) wer Dissipation [00..46 BA10393F (Note 42) wer Dissipation [00..46 BA10339F (Note 44) Po Po Po 0.2 0.2 0.2 0.0 0.0 0.0 0 25 50 75 100 125 0 25 50 75 100 125 0 25 50 75 100 125 Ambient Temperature [°C] Ambient Temperature [°C] Ambient Temperature [°C] (c)BA8391G (d)BA10393F (e)BA10339xx 1.0 1.0 BA2903F (Note 45) BA2903WF (Note 45) BA2903SF (Note 45) 0.8 0.8 BA2901FV (Note 48) wer Dissipation [W]00..46 BBBAAA222BB 999AA0002233399WFS00VF33FV FS(VN VF ((NoVMNtoMeo t( teN 4e( 6No 44)t6o e6)t ) e4 74)7 ) wer Dissipation [W]00..46 B A290BB 1AAS22F99V00 11 FS( FN(N o(Notetoe 4t e48 9)4)9 ) Po Po 0.2 0.2 0.0 0.0 0 25 50 75 100 125 150 0 25 50 75 100 125 150 Ambient Temperature [°C] Ambient Temperature [°C] (f)BA2903xxx BA2903Sxxx (g)BA2901xxx BA2901Sxxx (Note 41) (Note 42) (Note 43) (Note 44) (Note 45) (Note 46) (Note 47) (Note 48) (Note 49) Unit 5.4 6.2 7.0 4.9 6.2 5.5 4.7 7.0 4.9 mW/℃ When using the unit above Ta=25℃, subtract the value above per degree℃. Permissible dissipation is the value when FR4 glass epoxy board 70mm ×70mm ×1.6mm (cooper foil area below 3%) is mounted. Figure 115. Derating Curve www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 42/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Example of Circuit ○Reference voltage is VIN- IN VCC VRL IN + RL Vref - OUT Reference Time voltage Vref VEE OUT High While input voltage is bigger than reference voltage, output voltage is high. While input voltage is smaller than reference Low voltage, output voltage is low. Time ○Reference voltage is VIN+ IN VCC VRL Vref RL Reference + voltage Time - Vref OUT VEE High While input voltage is smaller than reference voltage, output Low voltage is high. While input voltage is bigger than reference Time voltage, output voltage is low. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 43/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Operational Notes 1. Reverse Connection of Power Supply Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply terminals. 2. Power Supply Lines Design the PCB layout pattern to provide low impedance ground and supply lines. Separate the ground and supply lines of the digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. Ground Voltage Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. Ground Wiring Pattern When using both small-signal and large-current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal ground caused by large currents. Also ensure that the ground traces of external components do not cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance. 5. Thermal Consideration Should by any chance the power dissipation rating be exceeded, the rise in temperature of the chip may result in deterioration of the properties of the chip. In case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the Pd rating. 6. Recommended Operating Conditions These conditions represent a range within which the expected characteristics of the IC can be approximately obtained. The electrical characteristics are guaranteed under the conditions of each parameter. 7. Inrush Current When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 8. Operation Under Strong Electromagnetic Field Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction. 9. Testing on Application Boards When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and storage. 10. Inter-pin Short and Mounting Errors Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground. Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 44/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Operational Notes – continued 11. Regarding Input Pins of the IC This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a parasitic diode or transistor. For example (refer to figure below): When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode. When GND > Pin B, the P-N junction operates as a parasitic transistor. Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be avoided. Figure 116. Example of Monolithic IC Structure 12. Unused Circuits When there are unused circuits it is recommended that they be connected as in Figure 117, setting the non-inverting input terminal to a potential within the in-phase input voltage range (VICR). Please keep this potential in VICM Figure 117. Disable Circuit Example 13. Ceramic Capacitor When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with temperature and the decrease in nominal capacitance due to DC bias and others. 14. Input Terminal Voltage (BA8391G / BA2903xxxx / BA2901xxx) Applying VEE + 36V to the input terminal is possible without causing deterioration of the electrical characteristics or destruction, irrespective of the supply voltage. However, this does not ensure normal circuit operation. Please note that the circuit operates normally only when the input voltage is within the common mode input voltage range of the electric characteristics. 15. Power Supply (single / split) The comparators when the specified voltage supplied is between VCC and VEE. Therefore, the single supply comparators can be used as a dual supply comparators as well. 16. Terminal short-circuits When the output and VCC terminals are shorted, excessive output current may flow, resulting in undue heat generation and, subsequently, destruction. 17. IC Handling Applying mechanical stress to the IC by deflecting or bending the board may cause fluctuations in the electrical characteristics due to piezo resistance effects. www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 45/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Physical Dimension Tape and Reel Information Package Name SSOP5 www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 46/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Physical Dimension Tape and Reel Information - continued Package Name SOP8 (Max 5.35 (include.BURR)) (UNIT : mm) PKG : SOP8 Drawing No. : EX112-5001-1 www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 47/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Physical Dimension Tape and Reel Information - continued Package Name SSOP-B8 www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 48/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Physical Dimension Tape and Reel Information - continued Package Name MSOP8 www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 49/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Physical Dimension Tape and Reel Information - continued Package Name SOP14 (Max 9.05 (include.BURR)) (UNIT : mm) PKG : SOP14 Drawing No. : EX113-5001 www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 50/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Physical Dimension Tape and Reel Information - continued Package Name SSOP-B14 www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 51/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Marking Diagrams SSOP5(TOP VIEW) SOP8 (TOP VIEW) P art Number Marking Part Number Marking LOT Number 1PIN MARK LOT Number SSOP-B8 (TOP VIEW) MSOP8 (TOP VIEW) Part Number Marking Part Number Marking LOT Number LOT Number 1PIN MARK 1PIN MARK SOP14 (TOP VIEW) SSOP-B14 (TOP VIEW) Part Number Marking Part Number Marking LOT Number LOT Number 1PIN MARK 1PIN MARK Product Name Package Type Marking BA8391 G SSOP5 D6 BA10393 F SOP8 10393 F SOP14 BA10339F BA10339 FV SSOP-B14 339 F SOP8 BA2903 FV SSOP-B8 FVM MSOP8 2903 F SOP8 BA2903W FV SSOP-B8 F SOP8 2903S BA2903S FV SSOP-B8 03S FVM MSOP8 2903S F SOP14 BA2901F BA2901 FV SSOP-B14 2901 F SOP14 BA2901S 2901S FV SSOP-B14 www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 52/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

Datasheet BA8391G BA10393F BA10339 Series BA2903 Series BA2901 Series Land Pattern Data All dimensions in mm Land Pitch Land Space Land Length Land Width PKG e MIE ≧ℓ 2 b2 SSOP5 0.95 2.4 1.0 0.6 SOP8 1.27 4.60 1.10 0.76 SOP14 SSOP-B8 0.65 4.60 1.20 0.35 SSOP-B14 MSOP8 0.65 2.62 0.99 0.35 SSOP5 SOP8, SOP14, SSOP-B8 SSOP-B14, MSOP8 e e MIE E MI e 2 ℓ b2 b 2 ℓ2 Revision History Date Revision Changes 23.Aug.2013 001 New Release 27.Nov.2013 002 Add the dB notation in Large Signal Voltage Gain 11.Dec.2013 003 Input offset voltage unit is changed from mA to mV in Page.1. 05.Jun.2015 004 Corrections. Update of Operational Notes www.rohm.com TSZ02201-0RFR0G200200-1-2 ©2013 ROHM Co., Ltd. All rights reserved. 53/53 05.Jun.2015 Rev.004 TSZ22111 • 15 • 001

DDaattaasshheeeett Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PGA-E Rev.001 © 2015 ROHM Co., Ltd. All rights reserved.

DDaattaasshheeeett Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PGA-E Rev.001 © 2015 ROHM Co., Ltd. All rights reserved.

DDaattaasshheeeett General Precaution 1. Before you use our Products, you are requested to carefully read this document and fully understand its contents. ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this document is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sale s representative. 3. The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or concerning such information. Notice – WE Rev.001 © 2015 ROHM Co., Ltd. All rights reserved.

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: R OHM Semiconductor: BA10339 BA10393 BA10393N