ICGOO在线商城 > 集成电路(IC) > 嵌入式 - 微控制器 > ATMEGA8535-16JUR
数量阶梯 | 香港交货 | 国内含税 |
+xxxx | $xxxx | ¥xxxx |
查看当月历史价格
查看今年历史价格
ATMEGA8535-16JUR产品简介:
ICGOO电子元器件商城为您提供ATMEGA8535-16JUR由Atmel设计生产,在icgoo商城现货销售,并且可以通过原厂、代理商等渠道进行代购。 ATMEGA8535-16JUR价格参考。AtmelATMEGA8535-16JUR封装/规格:嵌入式 - 微控制器, AVR 微控制器 IC AVR® ATmega 8-位 16MHz 8KB(4K x 16) 闪存 44-PLCC(16.59x16.59)。您可以下载ATMEGA8535-16JUR参考资料、Datasheet数据手册功能说明书,资料中有ATMEGA8535-16JUR 详细功能的应用电路图电压和使用方法及教程。
参数 | 数值 |
产品目录 | 集成电路 (IC) |
描述 | IC MCU 8BIT 8KB FLASH 44PLCC |
EEPROM容量 | 512 x 8 |
产品分类 | |
I/O数 | 32 |
品牌 | Atmel |
数据手册 | |
产品图片 | |
产品型号 | ATMEGA8535-16JUR |
RAM容量 | 512 x 8 |
rohs | 无铅 / 符合限制有害物质指令(RoHS)规范要求 |
产品系列 | AVR® ATmega |
产品培训模块 | http://www.digikey.cn/PTM/IndividualPTM.page?site=cn&lang=zhs&ptm=25692http://www.digikey.cn/PTM/IndividualPTM.page?site=cn&lang=zhs&ptm=26162http://www.digikey.cn/PTM/IndividualPTM.page?site=cn&lang=zhs&ptm=26159http://www.digikey.cn/PTM/IndividualPTM.page?site=cn&lang=zhs&ptm=26180 |
供应商器件封装 | 44-PLCC |
其它名称 | ATMEGA8535-16JURCT |
包装 | 剪切带 (CT) |
外设 | 欠压检测/复位,POR,PWM,WDT |
封装/外壳 | 44-LCC(J 形引线) |
工作温度 | -40°C ~ 85°C |
振荡器类型 | 内部 |
数据转换器 | A/D 8x10b |
标准包装 | 1 |
核心处理器 | AVR |
核心尺寸 | 8-位 |
电压-电源(Vcc/Vdd) | 4.5 V ~ 5.5 V |
程序存储器类型 | 闪存 |
程序存储容量 | 8KB(4K x 16) |
连接性 | I²C, SPI, UART/USART |
速度 | 16MHz |
Features • High-performance, Low-power AVR® 8-bit Microcontroller (cid:129) Advanced RISC Architecture – 130 Powerful Instructions – Most Single Clock Cycle Execution – 32 x 8 General Purpose Working Registers – Fully Static Operation – Up to 16 MIPS Throughput at 16 MHz – On-chip 2-cycle Multiplier (cid:129) Nonvolatile Program and Data Memories – 8K Bytes of In-System Self-Programmable Flash 8-bit Endurance: 10,000 Write/Erase Cycles – Optional Boot Code Section with Independent Lock Bits In-System Programming by On-chip Boot Program Microcontroller True Read-While-Write Operation – 512 Bytes EEPROM with 8K Bytes Endurance: 100,000 Write/Erase Cycles – 512 Bytes Internal SRAM In-System – Programming Lock for Software Security (cid:129) Peripheral Features Programmable – Two 8-bit Timer/Counters with Separate Prescalers and Compare Modes – One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Flash Mode – Real Time Counter with Separate Oscillator – Four PWM Channels – 8-channel, 10-bit ADC ATmega8535 8 Single-ended Channels 7 Differential Channels for TQFP Package Only 2 Differential Channels with Programmable Gain at 1x, 10x, or 200x for TQFP ATmega8535L Package Only – Byte-oriented Two-wire Serial Interface – Programmable Serial USART – Master/Slave SPI Serial Interface – Programmable Watchdog Timer with Separate On-chip Oscillator – On-chip Analog Comparator (cid:129) Special Microcontroller Features – Power-on Reset and Programmable Brown-out Detection – Internal Calibrated RC Oscillator – External and Internal Interrupt Sources – Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby and Extended Standby (cid:129) I/O and Packages – 32 Programmable I/O Lines – 40-pin PDIP, 44-lead TQFP, 44-lead PLCC, and 44-pad QFN/MLF (cid:129) Operating Voltages – 2.7 - 5.5V for ATmega8535L – 4.5 - 5.5V for ATmega8535 (cid:129) Speed Grades – 0 - 8 MHz for ATmega8535L – 0 - 16 MHz for ATmega8535 2502K–AVR–10/06
Pin Configurations Figure 1. Pinout ATmega8535 (XCK/T0) PB0 PA0 (ADC0) (T1) PB1 PA1 (ADC1) (INT2/AIN0) PB2 PA2 (ADC2) (OC0/AIN1) PB3 PA3 (ADC3) (SS) PB4 PA4 (ADC4) (MOSI) PB5 PA5 (ADC5) (MISO) PB6 PA6 (ADC6) (SCK) PB7 PA7 (ADC7) RESET AREF VCC GND GND AVCC XTAL2 PC7 (TOSC2) XTAL1 PC6 (TOSC1) (RXD) PD0 PC5 (TXD) PD1 PC4 (INT0) PD2 PC3 (INT1) PD3 PC2 (OC1B) PD4 PC1 (SDA) (OC1A) PD5 PC0 (SCL) (ICP1) PD6 PD7 (OC2) PLCC 44PB4 (SS)43PB3 (AIN1/OC0)42PB2 (AIN0/INT2)41PB1 (T1)40PB0 (XCK/T0)39GND38VCC37PA0 (ADC0)36PA1 (ADC1)35PA2 (ADC2)34PA3 (ADC3) PB4 (SS)PB3 (AIN1/OC0)PB2 (AIN0/INT2)PB1 (T1)PB0 (XCK/T0)GNDVCCPA0 (ADC0)PA1 (ADC1)PA2 (ADC2)PA3 (ADC3) (MOSI) PB5 1 33 PA4 (ADC4) (MOSI) PB5 7654321444342414039 PA4 (ADC4) (MISO) PB6 2 32 PA5 (ADC5) (MISO) PB6 8 38 PA5 (ADC5) (SCK) PB7 3 31 PA6 (ADC6) (SCK) PB7 9 37 PA6 (ADC6) RESET 4 30 PA7 (ADC7) RESET 10 36 PA7 (ADC7) VCC 5 29 AREF VCC 11 35 AREF GND 6 28 GND GND 12 34 GND XTAL2 7 27 AVCC XTAL2 13 33 AVCC XTAL1 8 26 PC7 (TOSC2) XTAL1 14 32 PC7 (TOSC2) (RXD) PD0 9 25 PC6 (TOSC1) (RXD) PD0 15 31 PC6 (TOSC1) (TXD) PD1 10 24 PC5 (TXD) PD1 16 30 PC5 (INT0) PD2 11 23 PC4 (INT0) PD2 17 29 PC4 1213141516171819202122 1819202122232425262728 (INT1) PD3(OC1B) PD4(OC1A) PD5(ICP1) PD6(OC2) PD7VCCGND(SCL) PC0(SDA) PC1 PC2 PC3 (INT1) PD3(OC1B) PD4(OC1A) PD5(ICP1) PD6(OC2) PD7VCCGND(SCL) PC0(SDA) PC1 PC2 PC3 NOTE: MLF Bottom pad should be soldered to ground. Disclaimer Typical values contained in this data sheet are based on simulations and characteriza- tion of other AVR microcontrollers manufactured on the same process technology. Min and Max values will be available after the device is characterized. ATmega8535(L) 2 2502K–AVR–10/06
ATmega8535(L) Overview The ATmega8535 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing instructions in a single clock cycle, the ATmega8535 achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed. Block Diagram Figure 2. Block Diagram PA0 - PA7 PC0 - PC7 VCC PORTA DRIVERS/BUFFERS PORTC DRIVERS/BUFFERS GND PORTA DIGITAL INTERFACE PORTC DIGITAL INTERFACE AVCC MUX & ADC TWI ADC INTERFACE AREF TIMERS/ PROGRAM STACK COUNTERS OSCILLATOR COUNTER POINTER PROGRAM INTERNAL SRAM FLASH OSCILLATOR XTAL1 INSTRUCTION GENERAL WATCHDOG OSCILLATOR REGISTER PURPOSE TIMER REGISTERS XTAL2 X INSTRUCTION MCU CTRL. DECODER Y & TIMING RESET Z CONTROL INTERRUPT INTERNAL CALIBRATED LINES ALU UNIT OSCILLATOR AVR CPU STATUS EEPROM REGISTER PROGLORAGMICMING SPI USART + COMP. - INTERFACE PORTB DIGITAL INTERFACE PORTD DIGITAL INTERFACE PORTB DRIVERS/BUFFERS PORTD DRIVERS/BUFFERS PB0 - PB7 PD0 - PD7 3 2502K–AVR–10/06
The AVR core combines a rich instruction set with 32 general purpose working registers. All 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers. The ATmega8535 provides the following features: 8K bytes of In-System Programmable Flash with Read-While-Write capabilities, 512 bytes EEPROM, 512 bytes SRAM, 32 general purpose I/O lines, 32 general purpose working registers, three flexible Timer/Counters with compare modes, internal and external interrupts, a serial program- mable USART, a byte oriented Two-wire Serial Interface, an 8-channel, 10-bit ADC with optional differential input stage with programmable gain in TQFP package, a program- mable Watchdog Timer with Internal Oscillator, an SPI serial port, and six software selectable power saving modes. The Idle mode stops the CPU while allowing the SRAM, Timer/Counters, SPI port, and interrupt system to continue functioning. The Power-down mode saves the register contents but freezes the Oscillator, disabling all other chip functions until the next interrupt or Hardware Reset. In Power-save mode, the asynchronous timer continues to run, allowing the user to maintain a timer base while the rest of the device is sleeping. The ADC Noise Reduction mode stops the CPU and all I/O modules except asynchronous timer and ADC, to minimize switching noise during ADC conversions. In Standby mode, the crystal/resonator Oscillator is running while the rest of the device is sleeping. This allows very fast start-up combined with low-power consumption. In Extended Standby mode, both the main Oscillator and the asynchro- nous timer continue to run. The device is manufactured using Atmel’s high density nonvolatile memory technology. The On-chip ISP Flash allows the program memory to be reprogrammed In-System through an SPI serial interface, by a conventional nonvolatile memory programmer, or by an On-chip Boot program running on the AVR core. The boot program can use any interface to download the application program in the Application Flash memory. Soft- ware in the Boot Flash section will continue to run while the Application Flash section is updated, providing true Read-While-Write operation. By combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a monolithic chip, the Atmel ATmega8535 is a powerful microcontroller that provides a highly flexible and cost effective solution to many embedded control applications. The ATmega8535 AVR is supported with a full suite of program and system develop- ment tools including: C compilers, macro assemblers, program debugger/simulators, In- Circuit Emulators, and evaluation kits. AT90S8535 Compatibility The ATmega8535 provides all the features of the AT90S8535. In addition, several new features are added. The ATmega8535 is backward compatible with AT90S8535 in most cases. However, some incompatibilities between the two microcontrollers exist. To solve this problem, an AT90S8535 compatibility mode can be selected by programming the S8535C fuse. ATmega8535 is pin compatible with AT90S8535, and can replace the AT90S8535 on current Printed Circuit Boards. However, the location of fuse bits and the electrical characteristics differs between the two devices. AT90S8535 Compatibility Programming the S8535C fuse will change the following functionality: Mode (cid:129) The timed sequence for changing the Watchdog Time-out period is disabled. See “Timed Sequences for Changing the Configuration of the Watchdog Timer” on page 45 for details. (cid:129) The double buffering of the USART Receive Register is disabled. See “AVR USART vs. AVR UART – Compatibility” on page 146 for details. ATmega8535(L) 4 2502K–AVR–10/06
ATmega8535(L) Pin Descriptions V Digital supply voltage. CC GND Ground. Port A (PA7..PA0) Port A serves as the analog inputs to the A/D Converter. Port A also serves as an 8-bit bi-directional I/O port, if the A/D Converter is not used. Port pins can provide internal pull-up resistors (selected for each bit). The Port A output buffers have symmetrical drive characteristics with both high sink and source capability. When pins PA0 to PA7 are used as inputs and are externally pulled low, they will source current if the internal pull-up resistors are activated. The Port A pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port B (PB7..PB0) Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port B output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up resistors are activated. The Port B pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port B also serves the functions of various special features of the ATmega8535 as listed on page 60. Port C (PC7..PC0) Port C is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port C output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port C pins that are externally pulled low will source current if the pull-up resistors are activated. The Port C pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port D (PD7..PD0) Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port D output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port D pins that are externally pulled low will source current if the pull-up resistors are activated. The Port D pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port D also serves the functions of various special features of the ATmega8535 as listed on page 64. RESET Reset input. A low level on this pin for longer than the minimum pulse length will gener- ate a reset, even if the clock is not running. The minimum pulse length is given in Table 15 on page 37. Shorter pulses are not guaranteed to generate a reset. XTAL1 Input to the inverting Oscillator amplifier and input to the internal clock operating circuit. XTAL2 Output from the inverting Oscillator amplifier. AVCC AVCC is the supply voltage pin for Port A and the A/D Converter. It should be externally connected to V , even if the ADC is not used. If the ADC is used, it should be con- CC nected to V through a low-pass filter. CC AREF AREF is the analog reference pin for the A/D Converter. 5 2502K–AVR–10/06
Resources A comprehensive set of development tools, application notes and datasheets are avail- able for download on http://www.atmel.com/avr. ATmega8535(L) 6 2502K–AVR–10/06
ATmega8535(L) About Code This documentation contains simple code examples that briefly show how to use various Examples parts of the device. These code examples assume that the part specific header file is included before compilation. Be aware that not all C compiler vendors include bit defini- tions in the header files and interrupt handling in C is compiler dependent. Please confirm with the C Compiler documentation for more details. 7 2502K–AVR–10/06
AVR CPU Core Introduction This section discusses the AVR core architecture in general. The main function of the CPU core is to ensure correct program execution. The CPU must therefore be able to access memories, perform calculations, control peripherals, and handle interrupts. Architectural Overview Figure 3. Block Diagram of the AVR MCU Architecture 8-bit Data Bus Program Status Flash Counter and Control Program Memory Interrupt 32 x 8 Unit Instruction General Register Purpose SPI Registrers Unit Instruction Watchdog Decoder Timer g g n ssin essi ALU Analog Control Lines dre ddr Comparator d A ct A ect Dire Indir I/O Module1 Data I/O Module 2 SRAM I/O Module n EEPROM I/O Lines In order to maximize performance and parallelism, the AVR uses a Harvard architecture – with separate memories and buses for program and data. Instructions in the program memory are executed with a single level pipelining. While one instruction is being exe- cuted, the next instruction is pre-fetched from the program memory. This concept enables instructions to be executed in every clock cycle. The program memory is In- System Re-Programmable Flash memory. The fast-access Register File contains 32 x 8-bit general purpose working registers with a single clock cycle access time. This allows single-cycle Arithmetic Logic Unit (ALU) operation. In a typical ALU operation, two operands are output from the Register File, the operation is executed, and the result is stored back in the Register File – in one clock cycle. ATmega8535(L) 8 2502K–AVR–10/06
ATmega8535(L) Six of the 32 registers can be used as three 16-bit indirect address register pointers for Data Space addressing – enabling efficient address calculations. One of the these address pointers can also be used as an address pointer for look up tables in Flash pro- gram memory. These added function registers are the 16-bit X-, Y-, and Z-registers, described later in this section. The ALU supports arithmetic and logic operations between registers or between a con- stant and a register. Single register operations can also be executed in the ALU. After an arithmetic operation, the Status Register is updated to reflect information about the result of the operation. Program flow is provided by conditional and unconditional jump and call instructions, able to directly address the whole address space. Most AVR instructions have a single 16-bit word format. Every program memory address contains a 16- or 32-bit instruction. Program Flash memory space is divided in two sections, the Boot Program section and the Application Program section. Both sections have dedicated Lock bits for write and read/write protection. The SPM instruction that writes into the Application Flash memory section must reside in the Boot Program section. During interrupts and subroutine calls, the return address Program Counter (PC) is stored on the Stack. The Stack is effectively allocated in the general data SRAM, and consequently the Stack size is only limited by the total SRAM size and the usage of the SRAM. All user programs must initialize the SP in the reset routine (before subroutines or interrupts are executed). The Stack Pointer SP is read/write accessible in the I/O space. The data SRAM can easily be accessed through the five different addressing modes supported in the AVR architecture. The memory spaces in the AVR architecture are all linear and regular memory maps. A flexible interrupt module has its control registers in the I/O space with an additional Global Interrupt Enable bit in the Status Register. All interrupts have a separate Interrupt Vector in the Interrupt Vector table. The interrupts have priority in accordance with their Interrupt Vector position. The lower the Interrupt Vector address, the higher the priority. The I/O memory space contains 64 addresses for CPU peripheral functions as Control Registers, SPI, and other I/O functions. The I/O Memory can be accessed directly, or as the Data Space locations following those of the Register File, 0x20 - 0x5F. ALU – Arithmetic Logic The high-performance AVR ALU operates in direct connection with all the 32 general Unit purpose working registers. Within a single clock cycle, arithmetic operations between general purpose registers or between a register and an immediate are executed. The ALU operations are divided into three main categories – arithmetic, logical, and bit-func- tions. Some implementations of the architecture also provide a powerful multiplier supporting both signed/unsigned multiplication and fractional format. See the “Instruc- tion Set” section for a detailed description. 9 2502K–AVR–10/06
Status Register The Status Register contains information about the result of the most recently executed arithmetic instruction. This information can be used for altering program flow in order to perform conditional operations. Note that the Status Register is updated after all ALU operations, as specified in the Instruction Set Reference. This will, in many cases, remove the need for using the dedicated compare instructions, resulting in faster and more compact code. The Status Register is not automatically stored when entering an interrupt routine and restored when returning from an interrupt. This must be handled by software. The AVR Status Register – SREG – is defined as: Bit 7 6 5 4 3 2 1 0 I T H S V N Z C SREG Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 7 – I: Global Interrupt Enable The Global Interrupt Enable bit must be set for the interrupts to be enabled. The individ- ual interrupt enable control is then performed in separate control registers. If the Global Interrupt Enable Register is cleared, none of the interrupts are enabled independent of the individual interrupt enable settings. The I-bit is cleared by hardware after an interrupt has occurred, and is set by the RETI instruction to enable subsequent interrupts. The I- bit can also be set and cleared by the application with the SEI and CLI instructions, as described in the instruction set reference. (cid:129) Bit 6 – T: Bit Copy Storage The Bit Copy instructions BLD (Bit LoaD) and BST (Bit STore) use the T-bit as source or destination for the operated bit. A bit from a register in the Register file can be copied into T by the BST instruction, and a bit in T can be copied into a bit in a register in the Register File by the BLD instruction. (cid:129) Bit 5 – H: Half Carry Flag The Half Carry Flag H indicates a Half Carry in some arithmetic operations. Half carry is useful in BCD arithmetic. See the “Instruction Set Description” for detailed information. (cid:129) Bit 4 – S: Sign Bit, S = N ⊕ V The S-bit is always an exclusive or between the Negative Flag N and the Two’s Comple- ment Overflow Flag V. See the “Instruction Set Description” for detailed information. (cid:129) Bit 3 – V: Two’s Complement Overflow Flag The Two’s Complement Overflow Flag V supports two’s complement arithmetics. See the “Instruction Set Description” for detailed information. (cid:129) Bit 2 – N: Negative Flag The Negative Flag N indicates a negative result in an arithmetic or logic operation. See the “Instruction Set Description” for detailed information. (cid:129) Bit 1 – Z: Zero Flag The Zero Flag Z indicates a zero result in an arithmetic or logic operation. See the “Instruction Set Description” for detailed information. (cid:129) Bit 0 – C: Carry Flag The Carry Flag C indicates a carry in an arithmetic or logic operation. See the “Instruc- tion Set Description” for detailed information. ATmega8535(L) 10 2502K–AVR–10/06
ATmega8535(L) General Purpose The Register File is optimized for the AVR Enhanced RISC instruction set. In order to Register File achieve the required performance and flexibility, the following input/output schemes are supported by the Register File: (cid:129) One 8-bit output operand and one 8-bit result input (cid:129) Two 8-bit output operands and one 8-bit result input (cid:129) Two 8-bit output operands and one 16-bit result input (cid:129) One 16-bit output operand and one 16-bit result input Figure 4 shows the structure of the 32 general purpose working registers in the CPU. Figure 4. AVR CPU General Purpose Working Registers 7 0 Addr. R0 0x00 R1 0x01 R2 0x02 … R13 0x0D General R14 0x0E Purpose R15 0x0F Working R16 0x10 Registers R17 0x11 … R26 0x1A X-register Low Byte R27 0x1B X-register High Byte R28 0x1C Y-register Low Byte R29 0x1D Y-register High Byte R30 0x1E Z-register Low Byte R31 0x1F Z-register High Byte Most of the instructions operating on the Register File have direct access to all registers, and most of them are single cycle instructions. As shown in Figure 4, each register is also assigned a data memory address, mapping them directly into the first 32 locations of the user Data Space. Although not being phys- ically implemented as SRAM locations, this memory organization provides great flexibility in access of the registers, as the X-, Y-, and Z-pointer Registers can be set to index any register in the file. 11 2502K–AVR–10/06
The X-register, Y-register, and The registers R26..R31 have some added functions to their general purpose usage. Z-register These registers are 16-bit address pointers for indirect addressing of the Data Space. The three indirect address registers X, Y, and Z are defined as described in Figure 5. Figure 5. The X-, Y-, and Z-registers 15 XH XL 0 X-register 7 0 7 0 R27 (0x1B) R26 (0x1A) 15 YH YL 0 Y-register 7 0 7 0 R29 (0x1D) R28 (0x1C) 15 ZH ZL 0 Z-register 7 0 7 0 R31 (0x1F) R30 (0x1E) In the different addressing modes, these address registers have functions as fixed dis- placement, automatic increment, and automatic decrement (see the instruction set reference for details). Stack Pointer The Stack is mainly used for storing temporary data, for storing local variables and for storing return addresses after interrupts and subroutine calls. The Stack Pointer Regis- ter always points to the top of the Stack. Note that the Stack is implemented as growing from higher memory locations to lower memory locations. This implies that a Stack PUSH command decreases the Stack Pointer. The Stack Pointer points to the data SRAM Stack area where the Subroutine and Inter- rupt Stacks are located. This Stack space in the data SRAM must be defined by the program before any subroutine calls are executed or interrupts are enabled. The Stack Pointer must be set to point above 0x60. The Stack Pointer is decremented by one when data is pushed onto the Stack with the PUSH instruction, and it is decremented by two when the return address is pushed onto the Stack with subroutine call or interrupt. The Stack Pointer is incremented by one when data is popped from the Stack with the POP instruction, and it is incremented by two when data is popped from the Stack with return from subroutine RET or return from interrupt RETI. The AVR Stack Pointer is implemented as two 8-bit registers in the I/O space. The num- ber of bits actually used is implementation dependent. Note that the data space in some implementations of the AVR architecture is so small that only SPL is needed. In this case, the SPH Register will not be present. Bit 15 14 13 12 11 10 9 8 - - - - - - SP9 SP8 SPH SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 SPL 7 6 5 4 3 2 1 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ATmega8535(L) 12 2502K–AVR–10/06
ATmega8535(L) Instruction Execution This section describes the general access timing concepts for instruction execution. The Timing AVR CPU is driven by the CPU clock clk , directly generated from the selected clock CPU source for the chip. No internal clock division is used. Figure 6 shows the parallel instruction fetches and instruction executions enabled by the Harvard architecture and the fast-access Register File concept. This is the basic pipelin- ing concept to obtain up to 1 MIPS per MHz with the corresponding unique results for functions per cost, functions per clocks, and functions per power-unit. Figure 6. The Parallel Instruction Fetches and Instruction Executions T1 T2 T3 T4 clk CPU 1st Instruction Fetch 1st Instruction Execute 2nd Instruction Fetch 2nd Instruction Execute 3rd Instruction Fetch 3rd Instruction Execute 4th Instruction Fetch Figure 7 shows the internal timing concept for the Register file. In a single clock cycle an ALU operation using two register operands is executed, and the result is stored back to the destination register. Figure 7. Single Cycle ALU Operation T1 T2 T3 T4 clk CPU Total Execution Time Register Operands Fetch ALU Operation Execute Result Write Back Reset and Interrupt The AVR provides several different interrupt sources. These interrupts and the separate Handling Reset Vector each have a separate Program Vector in the program memory space. All interrupts are assigned individual enable bits which must be written logic one together with the Global Interrupt Enable bit in the Status Register in order to enable the interrupt. Depending on the Program Counter value, interrupts may be automatically disabled when Boot Lock bits BLB02 or BLB12 are programmed. This feature improves software security. See the section “Memory Programming” on page 237 for details. The lowest addresses in the program memory space are, by default, defined as the Reset and Interrupt Vectors. The complete list of vectors is shown in “Interrupts” on page 46. The list also determines the priority levels of the different interrupts. The lower the address, the higher the priority level is. RESET has the highest priority, and next is INT0 – the External Interrupt Request 0. The Interrupt Vectors can be moved to the start of the Boot Flash section by setting the IVSEL bit in the General Interrupt Control Regis- ter (GICR). Refer to “Interrupts” on page 46 for more information. The Reset Vector can 13 2502K–AVR–10/06
also be moved to the start of the Boot Flash section by programming the BOOTRST Fuse, see “Boot Loader Support – Read-While-Write Self-Programming” on page 224. When an interrupt occurs, the Global Interrupt Enable I-bit is cleared and all interrupts are disabled. The user software can write logic one to the I-bit to enable nested inter- rupts. All enabled interrupts can then interrupt the current interrupt routine. The I-bit is automatically set when a Return from Interrupt instruction – RETI – is executed. There are basically two types of interrupts. The first type is triggered by an event that sets the interrupt flag. For these interrupts, the Program Counter is vectored to the actual Interrupt Vector in order to execute the interrupt handling routine, and hardware clears the corresponding interrupt flag. Interrupt flags can also be cleared by writing a logic one to the flag bit position(s) to be cleared. If an interrupt condition occurs while the corresponding interrupt enable bit is cleared, the interrupt flag will be set and remem- bered until the interrupt is enabled, or the flag is cleared by software. Similarly, if one or more interrupt conditions occur while the Global Interrupt Enable bit is cleared, the cor- responding interrupt flag(s) will be set and remembered until the Global Interrupt Enable bit is set, and will then be executed by order of priority. The second type of interrupts will trigger as long as the interrupt condition is present. These interrupts do not necessarily have interrupt flags. If the interrupt condition disap- pears before the interrupt is enabled, the interrupt will not be triggered. When the AVR exits from an interrupt, it will always return to the main program and exe- cute one more instruction before any pending interrupt is served. Note that the Status Register is not automatically stored when entering an interrupt rou- tine, nor restored when returning from an interrupt routine. This must be handled by software. When using the CLI instruction to disable interrupts, the interrupts will be immediately disabled. No interrupt will be executed after the CLI instruction, even if it occurs simulta- neously with the CLI instruction. The following example shows how this can be used to avoid interrupts during the timed EEPROM write sequence. Assembly Code Example in r16, SREG ; store SREG value cli ; disable interrupts during timed sequence sbi EECR, EEMWE ; start EEPROM write sbi EECR, EEWE out SREG, r16 ; restore SREG value (I-bit) C Code Example char cSREG; cSREG = SREG; /* store SREG value */ /* disable interrupts during timed sequence */ _CLI(); EECR |= (1<<EEMWE); /* start EEPROM write */ EECR |= (1<<EEWE); SREG = cSREG; /* restore SREG value (I-bit) */ ATmega8535(L) 14 2502K–AVR–10/06
ATmega8535(L) When using the SEI instruction to enable interrupts, the instruction following SEI will be executed before any pending interrupts, as shown in this example. Assembly Code Example sei ; set global interrupt enable sleep ; enter sleep, waiting for interrupt ; note: will enter sleep before any pending ; interrupt(s) C Code Example _SEI(); /* set global interrupt enable */ _SLEEP(); /* enter sleep, waiting for interrupt */ /* note: will enter sleep before any pending interrupt(s) */ Interrupt Response Time The interrupt execution response for all the enabled AVR interrupts is four clock cycles minimum. After four clock cycles, the Program Vector address for the actual interrupt handling routine is executed. During this four clock cycle period, the Program Counter is pushed onto the Stack. The Vector is normally a jump to the interrupt routine, and this jump takes three clock cycles. If an interrupt occurs during execution of a multi-cycle instruction, this instruction is completed before the interrupt is served. If an interrupt occurs when the MCU is in sleep mode, the interrupt execution response time is increased by four clock cycles. This increase comes in addition to the start-up time from the selected sleep mode. A return from an interrupt handling routine takes four clock cycles. During these four clock cycles, the Program Counter (two bytes) is popped back from the Stack, the Stack Pointer is incremented by two, and the I-bit in SREG is set. 15 2502K–AVR–10/06
AVR ATmega8535 This section describes the different memories in the ATmega8535. The AVR architec- Memories ture has two main memory spaces, the Data Memory and the Program Memory space. In addition, the ATmega8535 features an EEPROM Memory for data storage. All three memory spaces are linear and regular. In-System The ATmega8535 contains 8K bytes On-chip In-System Reprogrammable Flash mem- Reprogrammable Flash ory for program storage. Since all AVR instructions are 16 or 32 bits wide, the Flash is Program Memory organized as 4K x 16. For software security, the Flash Program memory space is divided into two sections, Boot Program section and Application Program section. The Flash memory has an endurance of at least 10,000 write/erase cycles. The ATmega8535 Program Counter (PC) is 12 bits wide, thus addressing the 4K program memory locations. The operation of Boot Program section and associated Boot Lock bits for software protection are described in detail in “Boot Loader Support – Read- While-Write Self-Programming” on page 224. “Memory Programming” on page 237 con- tains a detailed description on Flash Programming in SPI or Parallel Programming mode. Constant tables can be allocated within the entire program memory address space (see the LPM – Load Program Memory instruction description). Timing diagrams for instruction fetch and execution are presented in “Instruction Execu- tion Timing” on page 13. Figure 8. Program Memory Map $000 Application Flash Section Boot Flash Section $FFF ATmega8535(L) 16 2502K–AVR–10/06
ATmega8535(L) SRAM Data Memory Figure 9 shows how the ATmega8535 SRAM Memory is organized. The 608 Data Memory locations address the Register File, the I/O Memory, and the internal data SRAM. The first 96 locations address the Register File and I/O Memory, and the next 512 locations address the internal data SRAM. The five different addressing modes for the data memory cover: Direct, Indirect with Dis- placement, Indirect, Indirect with Pre-decrement, and Indirect with Post-increment. In the Register File, registers R26 to R31 feature the indirect addressing pointer registers. The direct addressing reaches the entire data space. The Indirect with Displacement mode reaches 63 address locations from the base address given by the Y- or Z-register. When using register indirect addressing modes with automatic pre-decrement and post- increment, the address registers X, Y, and Z are decremented or incremented. The 32 general purpose working registers, 64 I/O Registers, and the 512 bytes of inter- nal data SRAM in the ATmega8535 are all accessible through all these addressing modes. The Register File is described in “General Purpose Register File” on page 11. Figure 9. Data Memory Map Register File Data Address Space R0 $0000 R1 $0001 R2 $0002 ... ... R29 $001D R30 $001E R31 $001F I/O Registers $00 $0020 $01 $0021 $02 $0022 ... ... $3D $005D $3E $005E $3F $005F Internal SRAM $0060 $0061 ... $025E $025F 17 2502K–AVR–10/06
Data Memory Access Times This section describes the general access timing concepts for internal memory access. The internal data SRAM access is performed in two clk cycles as described in Figure CPU 10. Figure 10. On-chip Data SRAM Access Cycles T1 T2 T3 clk CPU Address Compute Address Address valid Data e Writ WR Data d a e R RD Memory Access Instruction Next Instruction EEPROM Data Memory The ATmega8535 contains 512 bytes of data EEPROM memory. It is organized as a separate data space, in which single bytes can be read and written. The EEPROM has an endurance of at least 100,000 write/erase cycles. The access between the EEPROM and the CPU is described in the following, specifying the EEPROM Address Registers, the EEPROM Data Register, and the EEPROM Control Register. “Memory Programming” on page 237 contains a detailed description on EEPROM Pro- gramming in SPI or Parallel Programming mode. EEPROM Read/Write Access The EEPROM Access Registers are accessible in the I/O space. The write access time for the EEPROM is given in Table 1. A self-timing function, how- ever, lets the user software detect when the next byte can be written. If the user code contains instructions that write the EEPROM, some precautions must be taken. In heavily filtered power supplies, V is likely to rise or fall slowly on Power-up/down. This CC causes the device, for some period of time, to run at a voltage lower than specified as minimum for the clock frequency used, see “Preventing EEPROM Corruption” on page 22 for details on how to avoid problems in these situations. In order to prevent unintentional EEPROM writes, a specific write procedure must be fol- lowed. Refer to the description of the EEPROM Control Register for details on this. When the EEPROM is read, the CPU is halted for four clock cycles before the next instruction is executed. When the EEPROM is written, the CPU is halted for two clock cycles before the next instruction is executed. ATmega8535(L) 18 2502K–AVR–10/06
ATmega8535(L) The EEPROM Address Register – EEARH and EEARL Bit 15 14 13 12 11 10 9 8 – – – – – – – EEAR8 EEARH EEAR7 EEAR6 EEAR5 EEAR4 EEAR3 EEAR2 EEAR1 EEAR0 EEARL 7 6 5 4 3 2 1 0 Read/Write R R R R R R R R/W R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 X X X X X X X X X (cid:129) Bits 15..9 – Res: Reserved Bits These bits are reserved bits in the ATmega8535 and will always read as zero. (cid:129) Bits 8..0 – EEAR8..0: EEPROM Address The EEPROM Address Registers – EEARH and EEARL specify the EEPROM address in the 512 bytes EEPROM space. The EEPROM data bytes are addressed linearly between 0 and 511. The initial value of EEAR is undefined. A proper value must be writ- ten before the EEPROM may be accessed. The EEPROM Data Register – EEDR Bit 7 6 5 4 3 2 1 0 MSB LSB EEDR Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bits 7..0 – EEDR7..0: EEPROM Data For the EEPROM write operation, the EEDR Register contains the data to be written to the EEPROM in the address given by the EEAR Register. For the EEPROM read oper- ation, the EEDR contains the data read out from the EEPROM at the address given by EEAR. The EEPROM Control Register – EECR Bit 7 6 5 4 3 2 1 0 – – – – EERIE EEMWE EEWE EERE EECR Read/Write R R R R R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 X 0 (cid:129) Bits 7..4 – Res: Reserved Bits These bits are reserved bits in the ATmega8535 and will always read as zero. (cid:129) Bit 3 – EERIE: EEPROM Ready Interrupt Enable Writing EERIE to one enables the EEPROM Ready Interrupt if the I-bit in SREG is set. Writing EERIE to zero disables the interrupt. The EEPROM Ready interrupt generates a constant interrupt when EEWE is cleared. (cid:129) Bit 2 – EEMWE: EEPROM Master Write Enable The EEMWE bit determines whether setting EEWE to one causes the EEPROM to be written. When EEMWE is set, setting EEWE within four clock cycles will write data to the EEPROM at the selected address If EEMWE is zero, setting EEWE will have no effect. When EEMWE has been written to one by software, hardware clears the bit to zero after four clock cycles. See the description of the EEWE bit for an EEPROM write procedure. (cid:129) Bit 1 – EEWE: EEPROM Write Enable The EEPROM Write Enable Signal EEWE is the write strobe to the EEPROM. When address and data are correctly set up, the EEWE bit must be written to one to write the 19 2502K–AVR–10/06
value into the EEPROM. The EEMWE bit must be written to one before a logical one is written to EEWE, otherwise no EEPROM write takes place. The following procedure should be followed when writing the EEPROM (the order of steps 3 and 4 is not essential): 1. Wait until EEWE becomes zero. 2. Wait until SPMEN in SPMCR becomes zero. 3. Write new EEPROM address to EEAR (optional). 4. Write new EEPROM data to EEDR (optional). 5. Write a logical one to the EEMWE bit while writing a zero to EEWE in EECR. 6. Within four clock cycles after setting EEMWE, write a logical one to EEWE. The EEPROM can not be programmed during a CPU write to the Flash memory. The software must check that the Flash programming is completed before initiating a new EEPROM write. Step 2 is only relevant if the software contains a Boot Loader allowing the CPU to program the Flash. If the Flash is never updated by the CPU, step 2 can be omitted. See “Boot Loader Support – Read-While-Write Self-Programming” on page 224 for details about Boot programming. Caution: An interrupt between step 5 and step 6 will make the write cycle fail, since the EEPROM Master Write Enable will time-out. If an interrupt routine accessing the EEPROM is interrupting another EEPROM access, the EEAR or EEDR Register will be modified, causing the interrupted EEPROM access to fail. It is recommended to have the Global Interrupt Flag cleared during all the steps to avoid these problems. When the write access time has elapsed, the EEWE bit is cleared by hardware. The user software can poll this bit and wait for a zero before writing the next byte. When EEWE has been set, the CPU is halted for two cycles before the next instruction is executed. (cid:129) Bit 0 – EERE: EEPROM Read Enable The EEPROM Read Enable Signal EERE is the read strobe to the EEPROM. When the correct address is set up in the EEAR Register, the EERE bit must be written to a logic one to trigger the EEPROM read. The EEPROM read access takes one instruction, and the requested data is available immediately. When the EEPROM is read, the CPU is halted for four cycles before the next instruction is executed. The user should poll the EEWE bit before starting the read operation. If a write operation is in progress, it is neither possible to read the EEPROM, nor to change the EEAR Register. The calibrated Oscillator is used to time the EEPROM accesses. Table 1 lists the typical programming time for EEPROM access from the CPU. Table 1. EEPROM Programming Time Number of Calibrated Typ Symbol RC Oscillator Cycles(1) Programming Time EEPROM Write (from CPU) 8448 8.4 ms Note: 1. Uses 1 MHz clock, independent of CKSEL Fuse settings. ATmega8535(L) 20 2502K–AVR–10/06
ATmega8535(L) The following code examples show one assembly and one C function for writing to the EEPROM. The examples assume that interrupts are controlled (e.g., by disabling inter- rupts globally) so that no interrupts will occur during execution of these functions. The examples also assume that no Flash Boot Loader is present in the software. If such code is present, the EEPROM write function must also wait for any ongoing SPM com- mand to finish. Assembly Code Example EEPROM_write: ; Wait for completion of previous write sbic EECR,EEWE rjmp EEPROM_write ; Set up address (r18:r17) in address register out EEARH, r18 out EEARL, r17 ; Write data (r16) to Data Register out EEDR,r16 ; Write logical one to EEMWE sbi EECR,EEMWE ; Start eeprom write by setting EEWE sbi EECR,EEWE ret C Code Example void EEPROM_write(unsigned int uiAddress, unsigned char ucData) { /* Wait for completion of previous write */ while(EECR & (1<<EEWE)) ; /* Set up Address and Data Registers */ EEAR = uiAddress; EEDR = ucData; /* Write logical one to EEMWE */ EECR |= (1<<EEMWE); /* Start eeprom write by setting EEWE */ EECR |= (1<<EEWE); } 21 2502K–AVR–10/06
The next code examples show assembly and C functions for reading the EEPROM. The examples assume that interrupts are controlled so that no interrupts will occur during execution of these functions. Assembly Code Example EEPROM_read: ; Wait for completion of previous write sbic EECR,EEWE rjmp EEPROM_read ; Set up address (r18:r17) in Address Register out EEARH, r18 out EEARL, r17 ; Start eeprom read by writing EERE sbi EECR,EERE ; Read data from Data Register in r16,EEDR ret C Code Example unsigned char EEPROM_read(unsigned int uiAddress) { /* Wait for completion of previous write */ while(EECR & (1<<EEWE)) ; /* Set up Address Register */ EEAR = uiAddress; /* Start eeprom read by writing EERE */ EECR |= (1<<EERE); /* Return data from Data Register */ return EEDR; } EEPROM Write During Power- When entering Power-down sleep mode while an EEPROM write operation is active, the down Sleep Mode EEPROM write operation will continue, and will complete before the write access time has passed. However, when the write operation is completed, the Oscillator continues running, and as a consequence, the device does not enter Power-down entirely. It is therefore recommended to verify that the EEPROM write operation is completed before entering Power-down. Preventing EEPROM During periods of low V , the EEPROM data can be corrupted because the supply volt- CC Corruption age is too low for the CPU and the EEPROM to operate properly. These issues are the same as for board level systems using EEPROM and the same design solutions should be applied. An EEPROM data corruption can be caused by two situations when the voltage is too low. First, a regular write sequence to the EEPROM requires a minimum voltage to operate correctly. Secondly, the CPU itself can execute instructions incorrectly, if the supply voltage is too low. ATmega8535(L) 22 2502K–AVR–10/06
ATmega8535(L) EEPROM data corruption can easily be avoided by following this design recommendation: Keep the AVR RESET active (low) during periods of insufficient power supply volt- age. This can be done by enabling the internal Brown-out Detector (BOD). If the detection level of the internal BOD does not match the needed detection level, an external low V Reset Protection circuit can be used. If a reset occurs while a write CC operation is in progress, the write operation will be completed provided that the power supply voltage is sufficient. I/O Memory The I/O space definition of the ATmega8535 is shown in page 299. All ATmega8535 I/Os and peripherals are placed in the I/O space. The I/O locations are accessed by the IN and OUT instructions, transferring data between the 32 general pur- pose working registers and the I/O space. I/O Registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these registers, the value of single bits can be checked by using the SBIS and SBIC instructions. Refer to the instruction set section for more details. When using the I/O specific commands IN and OUT, the I/O addresses 0x00 - 0x3F must be used. When addressing I/O Registers as data space using LD and ST instructions, 0x20 must be added to these addresses. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses should never be written. Some of the status flags are cleared by writing a logical one to them. Note that the CBI and SBI instructions will operate on all bits in the I/O Register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI instructions work with reg- isters 0x00 to 0x1F only. The I/O and peripherals control registers are explained in later sections. 23 2502K–AVR–10/06
System Clock and Clock Options Clock Systems and their Figure 11 presents the principal clock systems in the AVR and their distribution. All of Distribution the clocks need not be active at a given time. In order to reduce power consumption, the clocks to modules not being used can be halted by using different sleep modes, as described in “Power Management and Sleep Modes” on page 32. The clock systems are detailed below. Figure 11. Clock Distribution Asynchronous General I/O Flash and ADC CPU Core RAM Timer/Counter Modules EEPROM clk ADC clkI/O AVR Clock clkCPU Control Unit clk clk ASY FLASH Reset Logic Watchdog Timer Source clock Watchdog clock Clock Watchdog Multiplexer Oscillator Timer/Counter External RC Crystal Low-frequency Calibrated RC Oscillator Oscillator External Clock Oscillator Crystal Oscillator Oscillator CPU Clock – clk The CPU clock is routed to parts of the system concerned with operation of the AVR CPU core. Examples of such modules are the General Purpose Register File, the Status Reg- ister and the data memory holding the Stack Pointer. Halting the CPU clock inhibits the core from performing general operations and calculations. I/O Clock – clk The I/O clock is used by the majority of the I/O modules, like Timer/Counters, SPI, and I/O USART. The I/O clock is also used by the External Interrupt module, but note that some external interrupts are detected by asynchronous logic, allowing such interrupts to be detected even if the I/O clock is halted. Also note that address recognition in the TWI module is carried out asynchronously when clk is halted, enabling TWI address recep- I/O tion in all sleep modes. Flash Clock – clk The Flash clock controls operation of the Flash interface. The Flash clock is usually FLASH active simultaneously with the CPU clock. ATmega8535(L) 24 2502K–AVR–10/06
ATmega8535(L) Asynchronous Timer Clock – The Asynchronous Timer clock allows the Asynchronous Timer/Counter to be clocked clk directly from an external 32 kHz clock crystal. The dedicated clock domain allows using ASY this Timer/Counter as a real-time counter even when the device is in sleep mode. ADC Clock – clk The ADC is provided with a dedicated clock domain. This allows halting the CPU and ADC I/O clocks in order to reduce noise generated by digital circuitry. This gives more accu- rate ADC conversion results. Clock Sources The device has the following clock source options, selectable by Flash Fuse bits as shown below. The clock from the selected source is input to the AVR clock generator, and routed to the appropriate modules. Table 2. Device Clocking Options Select(1) Device Clocking Option CKSEL3..0 External Crystal/Ceramic Resonator 1111 - 1010 External Low-frequency Crystal 1001 External RC Oscillator 1000 - 0101 Calibrated Internal RC Oscillator 0100 - 0001 External Clock 0000 Note: 1. For all fuses “1” means unprogrammed while “0” means programmed. The various choices for each clocking option is given in the following sections. When the CPU wakes up from Power-down or Power-save, the selected clock source is used to time the start-up, ensuring stable Oscillator operation before instruction execution starts. When the CPU starts from Reset, there is as an additional delay allowing the power to reach a stable level before commencing normal operation. The Watchdog Oscillator is used for timing this real-time part of the start-up time. The number of WDT Oscillator cycles used for each time-out is shown in Table 3. The frequency of the Watchdog Oscil- lator is voltage dependent as shown in “ATmega8535 Typical Characteristics” on page 266. Table 3. Number of Watchdog Oscillator Cycles Typ Time-out (V = 5.0V) Typ Time-out (V = 3.0V) Number of Cycles CC CC 4.1 ms 4.3 ms 4K (4,096) 65 ms 69 ms 64K (65,536) Default Clock Source The device is shipped with CKSEL = “0001” and SUT = “10”. The default clock source setting is therefore the Internal RC Oscillator with longest startup time. This default set- ting ensures that all users can make their desired clock source setting using an In- System or Parallel Programmer. Crystal Oscillator XTAL1 and XTAL2 are input and output, respectively, of an inverting amplifier which can be configured for use as an On-chip Oscillator, as shown in Figure 12. Either a quartz crystal or a ceramic resonator may be used. The CKOPT Fuse selects between two dif- ferent oscillator amplifier modes. When CKOPT is programmed, the Oscillator output will oscillate will a full rail-to-rail swing on the output. This mode is suitable when operat- ing in a very noisy environment or when the output from XTAL2 drives a second clock buffer. This mode has a wide frequency range. When CKOPT is unprogrammed, the Oscillator has a smaller output swing. This reduces power consumption considerably. 25 2502K–AVR–10/06
This mode has a limited frequency range and it can not be used to drive other clock buffers. For resonators, the maximum frequency is 8 MHz with CKOPT unprogrammed and 16MHz with CKOPT programmed. C1 and C2 should always be equal for both crystals and resonators. The optimal value of the capacitors depends on the crystal or resonator in use, the amount of stray capacitance, and the electromagnetic noise of the environ- ment. Some initial guidelines for choosing capacitors for use with crystals are given in Table 4. For ceramic resonators, the capacitor values given by the manufacturer should be used. Figure 12. Crystal Oscillator Connections C2 XTAL2 C1 XTAL1 GND The Oscillator can operate in three different modes, each optimized for a specific fre- quency range. The operating mode is selected by the fuses CKSEL3..1 as shown in Table 4. Table 4. Crystal Oscillator Operating Modes Frequency Range Recommended Range for Capacitors CKOPT CKSEL3..1 (MHz) C1 and C2 for Use with Crystals (pF) 1 101(2) 0.4 - 0.9 – 1 110 0.9 - 3.0 12 - 22 1 111 3.0 - 8.0 12 - 22 0 101, 110, 111 1.0 - 16.0 12 - 22 2. This option should not be used with crystals, only with ceramic resonators. ATmega8535(L) 26 2502K–AVR–10/06
ATmega8535(L) The CKSEL0 fuse together with the SUT1..0 Fuses select the start-up times as shown in Table 5. Table 5. Start-up Times for the Crystal Oscillator Clock Selection Start-up Time from Additional Delay Power-down and from Reset CKSEL0 SUT1..0 Power-save (V = 5.0V) Recommended Usage CC 0 00 258 CK(1) 4.1 ms Ceramic resonator, fast rising power 0 01 258 CK(1) 65 ms Ceramic resonator, slowly rising power 0 10 1K CK(2) – Ceramic resonator, BOD enabled 0 11 1K CK(2) 4.1 ms Ceramic resonator, fast rising power 1 00 1K CK(2) 65 ms Ceramic resonator, slowly rising power 1 01 16K CK – Crystal Oscillator, BOD enabled 1 10 16K CK 4.1 ms Crystal Oscillator, fast rising power 1 11 16K CK 65 ms Crystal Oscillator, slowly rising power Notes: 1. These options should only be used when not operating close to the maximum fre- quency of the device, and only if frequency stability at start-up is not important for the application. These options are not suitable for crystals. 2. These options are intended for use with ceramic resonators and will ensure fre- quency stability at start-up. They can also be used with crystals when not operating close to the maximum frequency of the device, and if frequency stability at start-up is not important for the application. 27 2502K–AVR–10/06
Low-frequency Crystal To use a 32.768 kHz watch crystal as the clock source for the device, the Low-fre- Oscillator quency Crystal Oscillator must be selected by setting the CKSEL Fuses to “1001”. The crystal should be connected as shown in Figure 12. By programming the CKOPT Fuse, the user can enable internal capacitors on XTAL1 and XTAL2, thereby removing the need for external capacitors. The internal capacitors have a nominal value of 36 pF. When this Oscillator is selected, start-up times are determined by the SUT fuses as shown in Table 6. Table 6. Start-up Times for the Low-frequency Crystal Oscillator Clock Selection Start-up Time from Additional Delay Power-down and from Reset SUT1..0 Power-save (V = 5.0V) Recommended Usage CC 00 1K CK(1) 4.1 ms Fast rising power or BOD enabled 01 1K CK(1) 65 ms Slowly rising power 10 32K CK 65 ms Stable frequency at start-up 11 Reserved Note: 1. These options should only be used if frequency stability at start-up is not important for the application. External RC Oscillator For timing insensitive applications, the external RC configuration shown in Figure 13 can be used. The frequency is roughly estimated by the equation f = 1/(3RC). C should be at least 22 pF. By programming the CKOPT Fuse, the user can enable an internal 36pF capacitor between XTAL1 and GND, thereby removing the need for an external capacitor. For more information on Oscillator operation and details on how to choose R and C, refer to the External RC Oscillator application note. Figure 13. External RC Configuration V CC NC XTAL2 R XTAL1 C GND The Oscillator can operate in four different modes, each optimized for a specific fre- quency range. The operating mode is selected by the fuses CKSEL3..0 as shown in Table 7. ATmega8535(L) 28 2502K–AVR–10/06
ATmega8535(L) Table 7. External RC Oscillator Operating Modes CKSEL3..0 Frequency Range (MHz) 0101 0.1 - 0.9 0110 0.9 - 3.0 0111 3.0 - 8.0 1000 8.0 - 12.0 When this Oscillator is selected, start-up times are determined by the SUT fuses as shown in Table 8. Table 8. Start-up Times for the External RC Oscillator Clock Selection Start-up Time from Additional Delay Power-down and from Reset SUT1..0 Power-save (V = 5.0V) Recommended Usage CC 00 18 CK – BOD enabled 01 18 CK 4.1 ms Fast rising power 10 18 CK 65 ms Slowly rising power 11 6 CK(1) 4.1 ms Fast rising power or BOD enabled Note: 1. This option should not be used when operating close to the maximum frequency of the device. Calibrated Internal RC The calibrated internal RC Oscillator provides a fixed 1.0, 2.0, 4.0, or 8.0 MHz clock. All Oscillator frequencies are nominal values at 5V and 25°C. This clock may be selected as the sys- tem clock by programming the CKSEL Fuses as shown in Table 9. If selected, it will operate with no external components. The CKOPT Fuse should always be unpro- grammed when using this clock option. During Reset, hardware loads the calibration byte into the OSCCAL Register and thereby automatically calibrates the RC Oscillator. At 5V, 25°C and 1.0 MHz Oscillator frequency selected, this calibration gives a fre- quency within ± 3% of the nominal frequency. Using run-time calibration methods as described in application notes available at www.atmel.com/avr it is possible to achieve ±1% accuracy at any given V and Temperature. When this Oscillator is used as the CC chip clock, the Watchdog Oscillator will still be used for the Watchdog Timer and for the Reset Time-out. For more information on the pre-programmed calibration value, see the section “Calibration Byte” on page 239. Table 9. Internal Calibrated RC Oscillator Operating Modes CKSEL3..0 Nominal Frequency (MHz) 0001(1) 1.0 0010 2.0 0011 4.0 0100 8.0 Note: 1. The device is shipped with this option selected. When this Oscillator is selected, start-up times are determined by the SUT Fuses as shown in Table 10. XTAL1 and XTAL2 should be left unconnected (NC). 29 2502K–AVR–10/06
Table 10. Start-up Times for the Internal Calibrated RC Oscillator Clock Selection Start-up Time from Power- Additional Delay from SUT1..0 down and Power-save Reset (V = 5.0V) Recommended Usage CC 00 6 CK – BOD enabled 01 6 CK 4.1 ms Fast rising power 10(1) 6 CK 65 ms Slowly rising power 11 Reserved Note: 1. The device is shipped with this option selected. Oscillator Calibration Register – OSCCAL Bit 7 6 5 4 3 2 1 0 CAL7 CAL6 CAL5 CAL4 CAL3 CAL2 CAL1 CAL0 OSCCAL Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value Device Specific Calibration Value (cid:129) Bits 7..0 – CAL7..0: Oscillator Calibration Value Writing the calibration byte to this address will trim the Internal Oscillator to remove pro- cess variations from the Oscillator frequency. During Reset, the 1 MHz calibration value which is located in the signature row high byte (address 0x00) is automatically loaded into the OSCCAL Register. If the internal RC is used at other frequencies, the calibration values must be loaded manually. This can be done by first reading the signature row by a programmer, and then store the calibration values in the Flash or EEPROM. Then the value can be read by software and loaded into the OSCCAL Register. When OSCCAL is zero, the lowest available frequency is chosen. Writing non-zero val- ues to this register will increase the frequency of the Internal Oscillator. Writing 0xFF to the register gives the highest available frequency. The calibrated Oscillator is used to time EEPROM and Flash access. If EEPROM or Flash is written, do not calibrate to more than 10% above the nominal frequency. Otherwise, the EEPROM or Flash write may fail. Note that the Oscillator is intended for calibration to 1.0, 2.0, 4.0, or 8.0MHz. Tuning to other values is not guaranteed, as indicated in Table 11. Table 11. Internal RC Oscillator Frequency Range. Min Frequency in Percentage of Max Frequency in Percentage of OSCCAL Value Nominal Frequency (%) Nominal Frequency (%) 0x00 50 100 0x7F 75 150 0xFF 100 200 ATmega8535(L) 30 2502K–AVR–10/06
ATmega8535(L) External Clock To drive the device from an external clock source, XTAL1 should be driven as shown in Figure 14. To run the device on an external clock, the CKSEL Fuses must be pro- grammed to “0000”. By programming the CKOPT Fuse, the user can enable an internal 36 pF capacitor between XTAL1 and GND. Figure 14. External Clock Drive Configuration EXTERNAL CLOCK SIGNAL When this clock source is selected, start-up times are determined by the SUT Fuses as shown in Table 12. Table 12. Start-up Times for the External Clock Selection Start-up Time from Power- Additional Delay from SUT1..0 down and Power-save Reset (V = 5.0V) Recommended Usage CC 00 6 CK – BOD enabled 01 6 CK 4.1 ms Fast rising power 10 6 CK 65 ms Slowly rising power 11 Reserved When applying an external clock, it is required to avoid sudden changes in the applied clock frequency to ensure stable operation of the MCU. A variation in frequency of more than 2% from one clock cycle to the next can lead to unpredictable behavior. It is required to ensure that the MCU is kept in Reset during such changes in the clock frequency. Timer/Counter Oscillator For AVR microcontrollers with Timer/Counter Oscillator pins (TOSC1 and TOSC2), the crystal is connected directly between the pins. No external capacitors are needed. The Oscillator is optimized for use with a 32.768kHz watch crystal. Applying an external clock source to TOSC1 is not recommended. 31 2502K–AVR–10/06
Power Management Sleep modes enable the application to shut down unused modules in the MCU, thereby and Sleep Modes saving power. The AVR provides various sleep modes allowing the user to tailor the power consumption to the application’s requirements. To enter any of the six sleep modes, the SE bit in MCUCR must be written to logic one and a SLEEP instruction must be executed. The SM2, SM1, and SM0 bits in the MCUCR Register select which sleep mode (Idle, ADC Noise Reduction, Power-down, Power-save, Standby, or Extended Standby) will be activated by the SLEEP instruction. See Table 13 for a summary. If an enabled interrupt occurs while the MCU is in a sleep mode, the MCU wakes up. The MCU is then halted for four cycles in addition to the start-up time, it executes the interrupt routine, and resumes execution from the instruc- tion following SLEEP. The contents of the Register File and SRAM are unaltered when the device wakes up from sleep. If a Reset occurs during sleep mode, the MCU wakes up and executes from the Reset Vector. Figure 11 on page 24 presents the different clock systems in the ATmega8535, and their distribution. The figure is helpful in selecting an appropriate sleep mode. MCU Control Register – The MCU Control Register contains control bits for power management. MCUCR Bit 7 6 5 4 3 2 1 0 SM2 SE SM1 SM0 ISC11 ISC10 ISC01 ISC00 MCUCR Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bits 7, 5, 4 – SM2..0: Sleep Mode Select Bits 2, 1, and 0 These bits select between the six available sleep modes as shown in Table 13. Table 13. Sleep Mode Select SM2 SM1 SM0 Sleep Mode 0 0 0 Idle 0 0 1 ADC Noise Reduction 0 1 0 Power-down 0 1 1 Power-save 1 0 0 Reserved 1 0 1 Reserved 1 1 0 Standby(1) 1 1 1 Extended Standby(1) Note: 1. Standby mode and Extended Standby mode are only available with external crystals or resonators. (cid:129) Bit 6 – SE: Sleep Enable The SE bit must be written to logic one to make the MCU enter the sleep mode when the SLEEP instruction is executed. To avoid the MCU entering the sleep mode unless it is the programmers purpose, it is recommended to write the Sleep Enable (SE) bit to one just before the execution of the SLEEP instruction and to clear it immediately after wak- ing up. ATmega8535(L) 32 2502K–AVR–10/06
ATmega8535(L) Idle Mode When the SM2..0 bits are written to 000, the SLEEP instruction makes the MCU enter Idle mode, stopping the CPU but allowing SPI, USART, Analog Comparator, ADC, Two- wire Serial Interface, Timer/Counters, Watchdog, and the interrupt system to continue operating. This sleep mode basically halts clk and clk , while allowing the other CPU FLASH clocks to run. Idle mode enables the MCU to wake up from external triggered interrupts as well as internal ones like the Timer Overflow and USART Transmit Complete interrupts. If wake-up from the Analog Comparator interrupt is not required, the Analog Comparator can be powered down by setting the ADC bit in the Analog Comparator Control and Sta- tus register – ACSR. This will reduce power consumption in Idle mode. If the ADC is enabled, a conversion starts automatically when this mode is entered. ADC Noise Reduction When the SM2..0 bits are written to 001, the SLEEP instruction makes the MCU enter Mode ADC Noise Reduction mode, stopping the CPU but allowing the ADC, the External Inter- rupts, the Two-wire Serial Interface address watch, Timer/Counter2 and the Watchdog to continue operating (if enabled). This sleep mode basically halts clk , clk , and clk- I/O CPU , while allowing the other clocks to run. FLASH This improves the noise environment for the ADC, enabling higher resolution measure- ments. If the ADC is enabled, a conversion starts automatically when this mode is entered. Apart from the ADC Conversion Complete interrupt, only an External Reset, a Watchdog Reset, a Brown-out Reset, a Two-wire Serial Interface address match inter- rupt, a Timer/Counter2 interrupt, an SPM/EEPROM ready interrupt, an external level interrupt on INT0 or INT1, or an external interrupt on INT2 can wake up the MCU from ADC Noise Reduction mode. Power-down Mode When the SM2..0 bits are written to 010, the SLEEP instruction makes the MCU enter Power-down mode. In this mode, the External Oscillator is stopped, while the External Interrupts, the Two-wire Serial Interface address watch, and the Watchdog continue operating (if enabled). Only an External Reset, a Watchdog Reset, a Brown-out Reset, a Two-wire Serial Interface address match interrupt, an external level interrupt on INT0 or INT1, or an external interrupt on INT2 can wake up the MCU. This sleep mode basically halts all generated clocks, allowing operation of asynchronous modules only. Note that if a level triggered interrupt is used for wake-up from Power-down mode, the changed level must be held for some time to wake up the MCU. Refer to “External Inter- rupts” on page 68 for details. When waking up from Power-down mode, there is a delay from the wake-up condition occurs until the wake-up becomes effective. This allows the clock to restart and become stable after having been stopped. The wake-up period is defined by the same CKSEL fuses that define the Reset Time-out period, as described in “Clock Sources” on page 25. Power-save Mode When the SM2..0 bits are written to 011, the SLEEP instruction makes the MCU enter Power-save mode. This mode is identical to Power-down, with one exception: If Timer/Counter2 is clocked asynchronously, i.e., the AS2 bit in ASSR is set, Timer/Counter2 will run during sleep. The device can wake up from either Timer Over- flow or Output Compare event from Timer/Counter2 if the corresponding Timer/Counter2 interrupt enable bits are set in TIMSK, and the Global Interrupt Enable bit in SREG is set. If the asynchronous timer is NOT clocked asynchronously, Power-down mode is recom- mended instead of Power-save mode because the contents of the registers in the 33 2502K–AVR–10/06
asynchronous timer should be considered undefined after wake-up in Power-save mode if AS2 is 0. This sleep mode basically halts all clocks except clk , allowing operation only of asyn- ASY chronous modules, including Timer/Counter2 if clocked asynchronously. Standby Mode When the SM2..0 bits are 110 and an external crystal/resonator clock option is selected, the SLEEP instruction makes the MCU enter Standby mode. This mode is identical to Power-down with the exception that the Oscillator is kept running. From Standby mode, the device wakes up in six clock cycles. Extended Standby Mode When the SM2..0 bits are 111 and an external crystal/resonator clock option is selected, the SLEEP instruction makes the MCU enter Extended Standby mode. This mode is identical to Power-save mode with the exception that the Oscillator is kept running. From Extended Standby mode, the device wakes up in six clock cycles. Table 14. Active Clock Domains and Wake-up Sources in the Different Sleep Modes. Active Clock domains Oscillators Wake up sources Main Clock Timer INT2 TWI SPM/ A Sleep Source Osc INT1 Address Timer EEPROM D Other Mode clk clk clk clk clk Enabled Enabled INT0 Match 2 Ready C I/O CPU FLASH IO ADC ASY Idle X X X X X(2) X X X X X X ADC Noise X X X X(2) X(3) X X X X Reduction Power- X(3) X down Power- X(2) X(2) X(3) X X(2) save Standby(1) X X(3) X Extended X(2) X X(2) X(3) X X(2) Standby(1) Notes: 1. External Crystal or resonator selected as clock source 2. If AS2 bit in ASSR is set 3. Only INT2 or level interrupt INT1 and INT0 ATmega8535(L) 34 2502K–AVR–10/06
ATmega8535(L) Minimizing Power There are several issues to consider when trying to minimize the power consumption in Consumption an AVR controlled system. In general, sleep modes should be used as much as possi- ble, and the sleep mode should be selected so that as few as possible of the device’s functions are operating. All functions not needed should be disabled. In particular, the following modules may need special consideration when trying to achieve the lowest possible power consumption. Analog-to-Digital Converter If enabled, the ADC will be enabled in all sleep modes. To save power, the ADC should be disabled before entering any sleep mode. When the ADC is turned off and on again, the next conversion will be an extended conversion. Refer to “Analog-to-Digital Con- verter” on page 206 for details on ADC operation. Analog Comparator When entering Idle mode, the Analog Comparator should be disabled if not used. When entering ADC Noise Reduction mode, the Analog Comparator should be disabled. In the other sleep modes, the Analog Comparator is automatically disabled. However, if the Analog Comparator is set up to use the Internal Voltage Reference as input, the Analog Comparator should be disabled in all sleep modes. Otherwise, the Internal Voltage Ref- erence will be enabled, independent of sleep mode. Refer to “Analog Comparator” on page 203 for details on how to configure the Analog Comparator. Brown-out Detector If the Brown-out Detector is not needed in the application, this module should be turned off. If the Brown-out Detector is enabled by the BODEN Fuse, it will be enabled in all sleep modes, and hence, always consume power. In the deeper sleep modes, this will contribute significantly to the total current consumption. Refer to “Brown-out Detection” on page 39 for details on how to configure the Brown-out Detector. Internal Voltage Reference The Internal Voltage Reference will be enabled when needed by the Brown-out Detec- tor, the Analog Comparator or the ADC. If these modules are disabled as described in the sections above, the internal voltage reference will be disabled and it will not be con- suming power. When turned on again, the user must allow the reference to start up before the output is used. If the reference is kept on in sleep mode, the output can be used immediately. Refer to “Internal Voltage Reference” on page 41 for details on the start-up time. Watchdog Timer If the Watchdog Timer is not needed in the application, this module should be turned off. If the Watchdog Timer is enabled, it will be enabled in all sleep modes, and hence, always consume power. In the deeper sleep modes, this will contribute significantly to the total current consumption. Refer to “Watchdog Timer” on page 41 for details on how to configure the Watchdog Timer. Port Pins When entering a sleep mode, all port pins should be configured to use minimum power. The most important thing is then to ensure that no pins drive resistive loads. In sleep modes where both the I/O clock (clk ) and the ADC clock (clk ) are stopped, the I/O ADC input buffers of the device will be disabled. This ensures that no power is consumed by the input logic when not needed. In some cases, the input logic is needed for detecting wake-up conditions, and it will then be enabled. Refer to the section “Digital Input Enable and Sleep Modes” on page 55 for details on which pins are enabled. If the input buffer is enabled and the input signal is left floating or have an analog signal level close to V /2, the input buffer will use excessive power. CC 35 2502K–AVR–10/06
System Control and Reset Resetting the AVR During Reset, all I/O Registers are set to their initial values, and the program starts exe- cution from the Reset Vector. The instruction placed at the Reset Vector must be an RJMP instruction to the reset handling routine. If the program never enables an interrupt source, the Interrupt Vectors are not used, and regular program code can be placed at these locations. This is also the case if the Reset Vector is in the Application section while the Interrupt Vectors are in the Boot section or vice versa. The circuit diagram in Figure 15 shows the reset logic. Table 15 defines the electrical parameters of the reset circuitry. The I/O ports of the AVR are immediately reset to their initial state when a reset source goes active. This does not require any clock source to be running. After all reset sources have gone inactive, a delay counter is invoked, stretching the internal reset. This allows the power to reach a stable level before normal operation starts. The time-out period of the delay counter is defined by the user through the CKSEL Fuses. The different selections for the delay period are presented in “Clock Sources” on page 25. Reset Sources The ATmega8535 has four sources of Reset: (cid:129) Power-on Reset. The MCU is reset when the supply voltage is below the Power-on Reset threshold (V ). POT (cid:129) External Reset. The MCU is reset when a low level is present on the RESET pin for longer than the minimum pulse length. (cid:129) Watchdog Reset. The MCU is reset when the Watchdog Timer period expires and the Watchdog is enabled. (cid:129) Brown-out Reset. The MCU is reset when the supply voltage V is below the CC Brown-out Reset threshold (V ) and the Brown-out Detector is enabled. BOT ATmega8535(L) 36 2502K–AVR–10/06
ATmega8535(L) Figure 15. Reset Logic DATA BUS MCU Control and Status Register (MCUCSR) FFFF RRRR OOTD Power-on PBXW E Reset Circuit Brown-out BODEN Reset Circuit BODLEVEL Pull-up Resistor Spike Reset Circuit Filter Watchdog Timer Watchdog Oscillator Clock CK Delay Counters Generator TIMEOUT CKSEL[3:0] SUT[1:0] Table 15. Reset Characteristics Symbol Parameter Condition Min(1) Typ(1) Max(1) Units Power-on Reset Threshold 1.4 2.3 V Voltage (rising) V POT Power-on Reset Threshold 1.3 2.3 V Voltage (falling)(2) RESET Pin Threshold V 0.2 0.9 V RST Voltage Minimum pulse width on t 1.5 µs RST RESET Pin Brown-out Reset Threshold BODLEVEL = 1 2.5 2.7 2.9 VBOT Voltage(3) V BODLEVEL = 0 3.6 4.0 4.2 Minimum low voltage period BODLEVEL = 1 2 µs tBOD for Brown-out Detection BODLEVEL = 0 2 µs Brown-out Detector V 130 mV HYST hysteresis Notes: 1. Values are guidelines only. 2. The Power-on Reset will not work unless the supply voltage has been below V POT (falling). 37 2502K–AVR–10/06
3. V may be below nominal minimum operating voltage for some devices. For BOT devices where this is the case, the device is tested down to V = V during the CC BOT production test. This guarantees that a Brown-out Reset will occur before V drops CC to a voltage where correct operation of the microcontroller is no longer guaranteed. The test is performed using BODLEVEL = 1 for ATmega8535L and BODLEVEL = 0 for ATmega8535. BODLEVEL = 1 is not applicable for ATmega8535. Power-on Reset A Power-on Reset (POR) pulse is generated by an On-chip detection circuit. The detec- tion level is defined in Table 15. The POR is activated whenever V is below the CC detection level. The POR circuit can be used to trigger the Start-up Reset, as well as to detect a failure in supply voltage. A Power-on Reset (POR) circuit ensures that the device is reset from Power-on. Reach- ing the Power-on Reset threshold voltage invokes the delay counter, which determines how long the device is kept in RESET after V rise. The RESET signal is activated CC again, without any delay, when V decreases below the detection level. CC Figure 16. MCU Start-up, RESET Tied to V CC V V POT CC V RESET RST t TIME-OUT TOUT INTERNAL RESET Figure 17. MCU Start-up, RESET Extended Externally V POT V CC V RESET RST t TIME-OUT TOUT INTERNAL RESET ATmega8535(L) 38 2502K–AVR–10/06
ATmega8535(L) External Reset An External Reset is generated by a low level on the RESET pin. Reset pulses longer than the minimum pulse width (see Table 15) will generate a reset, even if the clock is not running. Shorter pulses are not guaranteed to generate a reset. When the applied signal reaches the Reset Threshold Voltage – V on its positive edge, the delay RST counter starts the MCU after the Time-out period t has expired. TOUT Figure 18. External Reset During Operation CC Brown-out Detection ATmega8535 has an On-chip Brown-out Detection (BOD) circuit for monitoring the V CC level during operation by comparing it to a fixed trigger level. The trigger level for the BOD can be selected by the fuse BODLEVEL to be 2.7V (BODLEVEL unprogrammed), or 4.0V (BODLEVEL programmed). The trigger level has a hysteresis to ensure spike free Brown-out Detection. The hysteresis on the detection level should be interpreted as V = V + V /2 and V = V - V /2. BOT+ BOT HYST BOT- BOT HYST The BOD circuit can be enabled/disabled by the fuse BODEN. When the BOD is enabled (BODEN programmed), and V decreases to a value below the trigger level CC (V in Figure 19), the Brown-out Reset is immediately activated. When V increases BOT- CC above the trigger level (V in Figure 19), the delay counter starts the MCU after the BOT+ time-out period t has expired. TOUT The BOD circuit will only detect a drop in V if the voltage stays below the trigger level CC for longer than t given in Table 15. BOD Figure 19. Brown-out Reset During Operation VCC V VBOT+ BOT- RESET TIME-OUT tTOUT INTERNAL RESET 39 2502K–AVR–10/06
Watchdog Reset When the Watchdog times out, it will generate a short reset pulse of one CK cycle dura- tion. On the falling edge of this pulse, the delay timer starts counting the Time-out period t . Refer to page 41 for details on operation of the Watchdog Timer. TOUT Figure 20. Watchdog Reset During Operation CC CK MCU Control and Status The MCU Control and Status Register provides information on which reset source Register – MCUCSR caused an MCU Reset. Bit 7 6 5 4 3 2 1 0 – ISC2 – – WDRF BORF EXTRF PORF MCUCSR Read/Write R/W R/W R R/W R/W R/W R/W R/W Initial Value 0 0 0 See Bit Description (cid:129) Bit 3 – WDRF: Watchdog Reset Flag This bit is set if a Watchdog Reset occurs. The bit is reset by a Power-on Reset, or by writing a logic zero to the flag. (cid:129) Bit 2 – BORF: Brown-out Reset Flag This bit is set if a Brown-out Reset occurs. The bit is reset by a Power-on Reset, or by writing a logic zero to the flag. (cid:129) Bit 1 – EXTRF: External Reset Flag This bit is set if an External Reset occurs. The bit is reset by a Power-on Reset, or by writing a logic zero to the flag. (cid:129) Bit 0 – PORF: Power-on Reset Flag This bit is set if a Power-on Reset occurs. The bit is reset only by writing a logic zero to the flag. To make use of the Reset Flags to identify a reset condition, the user should read and then reset the MCUCSR as early as possible in the program. If the register is cleared before another reset occurs, the source of the reset can be found by examining the Reset Flags. ATmega8535(L) 40 2502K–AVR–10/06
ATmega8535(L) Internal Voltage ATmega8535 features an internal bandgap reference. This reference is used for Brown- Reference out Detection, and it can be used as an input to the Analog Comparator or the ADC. The 2.56V reference to the ADC is generated from the internal bandgap reference. Voltage Reference Enable The voltage reference has a start-up time that may influence the way it should be used. Signals and Start-up Time The start-up time is given in Table 16. To save power, the reference is not always turned on. The reference is on during the following situations: 1. When the BOD is enabled (by programming the BODEN Fuse). 2. When the bandgap reference is connected to the Analog Comparator (by setting the ACBG bit in ACSR). 3. When the ADC is enabled. Thus, when the BOD is not enabled, after setting the ACBG bit or enabling the ADC, the user must always allow the reference to start up before the output from the Analog Com- parator or ADC is used. To reduce power consumption in Power-down mode, the user can avoid the three conditions above to ensure that the reference is turned off before entering Power-down mode. Table 16. Internal Voltage Reference Characteristics(1) Symbol Parameter Min Typ Max Units V Bandgap reference voltage 1.15 1.23 1.35 V BG t Bandgap reference start-up time 40 70 µs BG I Bandgap reference current consumption 10 µA BG Note: 1. Values are guidelines only. Watchdog Timer The Watchdog Timer is clocked from a separate On-chip Oscillator which runs at 1MHz. This is the typical value at V = 5V. See characterization data for typical values CC at other V levels. By controlling the Watchdog Timer prescaler, the Watchdog Reset CC interval can be adjusted as shown in Table 18 on page 43. The WDR – Watchdog Reset – instruction resets the Watchdog Timer. The Watchdog Timer is also reset when it is disabled and when a Chip Reset occurs. Eight different clock cycle periods can be selected to determine the reset period. If the reset period expires without another Watchdog Reset, the ATmega8535 resets and executes from the Reset Vector. For tim- ing details on the Watchdog Reset, refer to page 40. To prevent unintentional disabling of the Watchdog or unintentional change of Time-out period, three different safety levels are selected by the Fuses S8535C and WDTON as shown in Table 17. Safety level 0 corresponds to the setting in AT90S8535. There is no restriction on enabling the WDT in any of the safety levels. 41 2502K–AVR–10/06
Table 17. WDT Configuration as a Function of the Fuse Settings of S8538C and WDTON How to Safety WDT Initial How to Disable Change S8535C WDTON Level State the WDT Time-out Unprogrammed Unprogrammed 1 Disabled Timed Timed sequence sequence Unprogrammed Programmed 2 Enabled Always enabled Timed sequence Programmed Unprogrammed 0 Disabled Timed No sequence restriction Programmed Programmed 2 Enabled Always enabled Timed sequence Figure 21. Watchdog Timer WATCHDOG OSCILLATOR Watchdog Timer Control Register – WDTCR Bit 7 6 5 4 3 2 1 0 – – – WDCE WDE WDP2 WDP1 WDP0 WDTCR Read/Write R R R R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bits 7..5 – Res: Reserved Bits These bits are reserved bits in the ATmega8535 and will always read as zero. (cid:129) Bit 4 – WDCE: Watchdog Change Enable This bit must be set when the WDE bit is written to logic zero. Otherwise, the Watchdog will not be disabled. Once written to one, hardware will clear this bit after four clock cycles. Refer to the description of the WDE bit for a Watchdog disable procedure. In Safety Level 1 and 2, this bit must also be set when changing the prescaler bits. See “Timed Sequences for Changing the Configuration of the Watchdog Timer” on page 45. (cid:129) Bit 3 – WDE: Watchdog Enable When the WDE is written to logic one, the Watchdog Timer is enabled, and if the WDE is written to logic zero, the Watchdog Timer function is disabled. WDE can only be cleared ATmega8535(L) 42 2502K–AVR–10/06
ATmega8535(L) if the WDCE bit has logic level one. To disable an enabled Watchdog Timer, the follow- ing procedure must be followed: 1. In the same operation, write a logic one to WDCE and WDE. A logic one must be written to WDE even though it is set to one before the disable operation starts. 2. Within the next four clock cycles, write a logic 0 to WDE. This disables the watchdog. In safety level 2, it is not possible to disable the Watchdog Timer, even with the algo- rithm described above. See “Timed Sequences for Changing the Configuration of the Watchdog Timer” on page 45. (cid:129) Bits 2..0 – WDP2, WDP1, WDP0: Watchdog Timer Prescaler 2, 1, and 0 The WDP2, WDP1, and WDP0 bits determine the Watchdog Timer prescaling when the Watchdog Timer is enabled. The different prescaling values and their corresponding Timeout Periods are shown in Table 18. Table 18. Watchdog Timer Prescale Select(1) Number of WDT Typical Time-out Typical Time-out WDP2 WDP1 WDP0 Oscillator Cycles at V = 3.0V at V = 5.0V CC CC 0 0 0 16K (16,384) 17.1 ms 16.3 ms 0 0 1 32K (32,768) 34.3 ms 32.5 ms 0 1 0 64K (65,536) 68.5 ms 65 ms 0 1 1 128K (131,072) 0.14 s 0.13 s 1 0 0 256K (262,144) 0.27 s 0.26 s 1 0 1 512K (524,288) 0.55 s 0.52 s 1 1 0 1,024K (1,048,576) 1.1 s 1.0 s 1 1 1 2,048K (2,097,152) 2.2 s 2.1 s Note: 1. Values are guidelines only. 43 2502K–AVR–10/06
The following code example shows one assembly and one C function for turning off the WDT. The example assumes that interrupts are controlled (e.g., by disabling interrupts globally) so that no interrupts will occur during execution of these functions. Assembly Code Example WDT_off: ; Reset WDT wdr ; Write logical one to WDCE and WDE in r16, WDTCR ori r16, (1<<WDCE)|(1<<WDE) out WDTCR, r16 ; Turn off WDT ldi r16, (0<<WDE) out WDTCR, r16 ret C Code Example void WDT_off(void) { /* Reset WDT */ _WDR() /* Write logical one to WDCE and WDE */ WDTCR |= (1<<WDCE) | (1<<WDE); /* Turn off WDT */ WDTCR = 0x00; } ATmega8535(L) 44 2502K–AVR–10/06
ATmega8535(L) Timed Sequences for The sequence for changing the Watchdog Timer configuration differs slightly between Changing the the three safety levels. Separate procedures are described for each level. Configuration of the Watchdog Timer Safety Level 0 This mode is compatible with the Watchdog operation found in AT90S8535. The Watch- dog Timer is initially disabled, but can be enabled by writing the WDE bit to 1 without any restriction. The Time-out period can be changed at any time without restriction. To disable an enabled Watchdog Timer and/or changing the Watchdog Time-out, the fol- lowing procedure must be followed: 1. In the same operation, write a logic one to WDCE and WDE. A logic one must be written to WDE regardless of the previous value of the WDE bit. 2. Within the next four clock cycles, in the same operation, write the WDE and WDP bits as desired, but with the WDCE bit cleared. Safety Level 1 In this mode, the Watchdog Timer is initially disabled, but can be enabled by writing the WDE bit to 1 without any restriction. A timed sequence is needed when changing the Watchdog Time-out period or disabling an enabled Watchdog Timer. To disable an enabled Watchdog Timer and/or changing the Watchdog Time-out, the following proce- dure must be followed: 1. In the same operation, write a logic one to WDCE and WDE. A logic one must be written to WDE regardless of the previous value of the WDE bit. 2. Within the next four clock cycles, in the same operation, write the WDE and WDP bits as desired, but with the WDCE bit cleared. Safety Level 2 In this mode, the Watchdog Timer is always enabled, and the WDE bit will always read as one. A timed sequence is needed when changing the Watchdog Time-out period. To change the Watchdog Time-out, the following procedure must be followed: 1. In the same operation, write a logical one to WDCE and WDE. Even though the WDE always is set, the WDE must be written to one to start the timed sequence. 2. Within the next four clock cycles, in the same operation, write the WDP bits as desired, but with the WDCE bit cleared. The value written to the WDE bit is irrelevant. 45 2502K–AVR–10/06
Interrupts This section describes the specifics of the interrupt handling as performed in ATmega8535. For a general explanation of the AVR interrupt handling, refer to “Reset and Interrupt Handling” on page 13. Interrupt Vectors in Table 19. Reset and Interrupt Vectors ATmega8535 Vector Program No. Address(2) Source Interrupt Definition 1 0x000(1) RESET External Pin, Power-on Reset, Brown-out Reset and Watchdog Reset 2 0x001 INT0 External Interrupt Request 0 3 0x002 INT1 External Interrupt Request 1 4 0x003 TIMER2 COMP Timer/Counter2 Compare Match 5 0x004 TIMER2 OVF Timer/Counter2 Overflow 6 0x005 TIMER1 CAPT Timer/Counter1 Capture Event 7 0x006 TIMER1 COMPA Timer/Counter1 Compare Match A 8 0x007 TIMER1 COMPB Timer/Counter1 Compare Match B 9 0x008 TIMER1 OVF Timer/Counter1 Overflow 10 0x009 TIMER0 OVF Timer/Counter0 Overflow 11 0x00A SPI, STC Serial Transfer Complete 12 0x00B USART, RXC USART, Rx Complete 13 0x00C USART, UDRE USART Data Register Empty 14 0x00D USART, TXC USART, Tx Complete 15 0x00E ADC ADC Conversion Complete 16 0x00F EE_RDY EEPROM Ready 17 0x010 ANA_COMP Analog Comparator 18 0x011 TWI Two-wire Serial Interface 19 0x012 INT2 External Interrupt Request 2 20 0x013 TIMER0 COMP Timer/Counter0 Compare Match 21 0x014 SPM_RDY Store Program Memory Ready Notes: 1. When the BOOTRST Fuse is programmed, the device will jump to the Boot Loader address at reset, see “Boot Loader Support – Read-While-Write Self-Programming” on page 224. 2. When the IVSEL bit in GICR is set, Interrupt Vectors will be moved to the start of the Boot Flash section. The address of each Interrupt Vector will then be the address in this table added to the start address of the Boot Flash section. Table 20 shows reset and Interrupt Vectors placement for the various combinations of BOOTRST and IVSEL settings. If the program never enables an interrupt source, the Interrupt Vectors are not used, and regular program code can be placed at these loca- tions. This is also the case if the Reset Vector is in the Application section while the Interrupt Vectors are in the Boot section or vice versa. ATmega8535(L) 46 2502K–AVR–10/06
ATmega8535(L) Table 20. Reset and Interrupt Vectors Placement BOOTRST(1) IVSEL Reset Address Interrupt Vectors Start Address 1 0 0x0000 0x0001 1 1 0x0000 Boot Reset Address + 0x0001 0 0 Boot Reset Address 0x0001 0 1 Boot Reset Address Boot Reset Address + 0x0001 Note: 1. The Boot Reset Address is shown in Table 93 on page 235. For the BOOTRST Fuse “1” means unprogrammed while “0” means programmed. The most typical and general program setup for the Reset and Interrupt Vector Addresses in ATmega8535 is: AddressLabels Code Comments 0x000 rjmp RESET ; Reset Handler 0x001 rjmp EXT_INT0 ; IRQ0 Handler 0x002 rjmp EXT_INT1 ; IRQ1 Handler 0x003 rjmp TIM2_COMP ; Timer2 Compare Handler 0x004 rjmp TIM2_OVF ; Timer2 Overflow Handler 0x005 rjmp TIM1_CAPT ; Timer1 Capture Handler 0x006 rjmp TIM1_COMPA ; Timer1 Compare A Handler 0x007 rjmp TIM1_COMPB ; Timer1 Compare B Handler 0x008 rjmp TIM1_OVF ; Timer1 Overflow Handler 0x009 rjmp TIM0_OVF ; Timer0 Overflow Handler 0x00A rjmp SPI_STC ; SPI Transfer Complete Handler 0x00B rjmp USART_RXC ; USART RX Complete Handler 0x00C rjmp USART_UDRE ; UDR Empty Handler 0x00D rjmp USART_TXC ; USART TX Complete Handler 0x00E rjmp ADC ; ADC Conversion Complete Handler 0x00F rjmp EE_RDY ; EEPROM Ready Handler 0x010 rjmp ANA_COMP ; Analog Comparator Handler 0x011 rjmp TWSI ; Two-wire Serial Interface Handler 0x012 rjmp EXT_INT2 ; IRQ2 Handler 0x013 rjmp TIM0_COMP ; Timer0 Compare Handler 0x014 rjmp SPM_RDY ; Store Program Memory Ready Handler ; 0x015RESET: ldi r16,high(RAMEND) ; Main program start 0x016 out SPH,r16 ; Set Stack Pointer to top of RAM 0x017 ldi r16,low(RAMEND) 0x018 out SPL,r16 0x019 sei ; Enable interrupts 0x020 <instr> xxx ... ... ... When the BOOTRST Fuse is unprogrammed, the Boot section size set to 2K bytes and the IVSEL bit in the GICR Register is set before any interrupts are enabled, the most typical and general program setup for the Reset and Interrupt Vector Addresses is: 47 2502K–AVR–10/06
AddressLabels Code Comments 0x000RESET: ldi r16,high(RAMEND) ; Main program start 0x001 out SPH,r16 ; Set Stack Pointer to top of RAM 0x002 ldi r16,low(RAMEND) 0x003 out SPL,r16 0x004 sei ; Enable interrupts 0x005 <instr> xxx ; .org 0xC01 0xC01 rjmp EXT_INT0 ; IRQ0 Handler 0xC02 rjmp EXT_INT1 ; IRQ1 Handler ... .... .. ; 0xC14 rjmp SPM_RDY ; Store Program Memory Ready Handler When the BOOTRST Fuse is programmed and the Boot section size set to 2K bytes, the most typical and general program setup for the Reset and Interrupt Vector Addresses is: AddressLabels Code Comments .org 0x001 0x001 rjmp EXT_INT0 ; IRQ0 Handler 0x002 rjmp EXT_INT1 ; IRQ1 Handler ... .... .. ; 0x014 rjmp SPM_RDY ; Store Program Memory Ready Handler ; .org 0xC00 0xC00RESET: ldi r16,high(RAMEND) ; Main program start 0xC01 out SPH,r16 ; Set Stack Pointer to top of RAM 0xC02 ldi r16,low(RAMEND) 0xC03 out SPL,r16 0xC04 sei ; Enable interrupts 0xC05 <instr> xxx When the BOOTRST Fuse is programmed, the Boot section size set to 2K bytes and the IVSEL bit in the GICR Register is set before any interrupts are enabled, the most typical and general program setup for the Reset and Interrupt Vector Addresses is: AddressLabels Code Comments .org 0xC00 0xC00 rjmp RESET ; Reset handler 0xC01 rjmp EXT_INT0 ; IRQ0 Handler 0xC02 rjmp EXT_INT1 ; IRQ1 Handler ... .... .. ; 0xC14 rjmp SPM_RDY ; Store Program Memory Ready Handler ; 0xC15RESET: ldi r16,high(RAMEND) ;Main program start 0xC16 out SPH,r16 ; Set Stack Pointer to top of RAM 0xC17 ldi r16,low(RAMEND) 0xC18 out SPL,r16 0xC19 sei ; Enable interrupts 0xC20 <instr> xxx ATmega8535(L) 48 2502K–AVR–10/06
ATmega8535(L) Moving Interrupts Between The General Interrupt Control Register controls the placement of the Interrupt Vector Application and Boot Space table. General Interrupt Control Register – GICR Bit 7 6 5 4 3 2 1 0 INT1 INT0 INT2 – – – IVSEL IVCE GICR Read/Write R/W R/W R/W R R R R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 1 – IVSEL: Interrupt Vector Select When the IVSEL bit is cleared (zero), the Interrupt Vectors are placed at the start of the Flash memory. When this bit is set (one), the Interrupt Vectors are moved to the begin- ning of the Boot Loader section of the Flash. The actual address of the start of the Boot Flash section is determined by the BOOTSZ Fuses. Refer to the section “Boot Loader Support – Read-While-Write Self-Programming” on page 224 for details. To avoid unin- tentional changes of Interrupt Vector tables, a special write procedure must be followed to change the IVSEL bit: 1. Write the Interrupt Vector Change Enable (IVCE) bit to one. 2. Within four cycles, write the desired value to IVSEL while writing a zero to IVCE. Interrupts will automatically be disabled while this sequence is executed. Interrupts are disabled in the cycle IVCE is set, and they remain disabled until after the instruction fol- lowing the write to IVSEL. If IVSEL is not written, interrupts remain disabled for four cycles. The I-bit in the Status Register is unaffected by the automatic disabling. Note: If Interrupt Vectors are placed in the Boot Loader section and Boot Lock bit BLB02 is pro- grammed, interrupts are disabled while executing from the Application section. If Interrupt Vectors are placed in the Application section and Boot Lock bit BLB12 is pro- gramed, interrupts are disabled while executing from the Boot Loader section. Refer to the section “Boot Loader Support – Read-While-Write Self-Programming” on page 224 for details on Boot Lock bits. (cid:129) Bit 0 – IVCE: Interrupt Vector Change Enable The IVCE bit must be written to logic one to enable change of the IVSEL bit. IVCE is cleared by hardware four cycles after it is written or when IVSEL is written. Setting the IVCE bit will disable interrupts, as explained in the IVSEL description above. See Code Example below. 49 2502K–AVR–10/06
Assembly Code Example Move_interrupts: ; Enable change of interrupt vectors ldi r16, (1<<IVCE) out GICR, r16 ; Move interrupts to boot Flash section ldi r16, (1<<IVSEL) out GICR, r16 ret C Code Example void Move_interrupts(void) { /* Enable change of interrupt vectors */ GICR = (1<<IVCE); /* Move interrupts to boot Flash section */ GICR = (1<<IVSEL); } ATmega8535(L) 50 2502K–AVR–10/06
ATmega8535(L) I/O-Ports Introduction All AVR ports have true Read-Modify-Write functionality when used as general digital I/O ports. This means that the direction of one port pin can be changed without uninten- tionally changing the direction of any other pin with the SBI and CBI instructions. The same applies when changing drive value (if configured as output) or enabling/disabling of pull-up resistors (if configured as input). Each output buffer has symmetrical drive characteristics with both high sink and source capability. The pin driver is strong enough to drive LED displays directly. All port pins have individually selectable pull-up resistors with a supply-voltage invariant resistance. All I/O pins have protection diodes to both V and Ground as indicated in Figure 22. Refer to “Electrical Characteristics” on page CC 255 for a complete list of parameters. Figure 22. I/O Pin Equivalent Schematic R pu Pxn Logic C pin See Figure "General Digital I/O" for Details All registers and bit references in this section are written in general form. A lower case “x” represents the numbering letter for the port, and a lower case “n” represents the bit number. However, when using the register or bit defines in a program, the precise form must be used. For example, PORTB3 for bit no. 3 in Port B, here documented generally as PORTxn. The physical I/O Registers and bit locations are listed in “Register Descrip- tion for I/O-Ports” on page 66. Three I/O memory address locations are allocated for each port, one each for the Data Register – PORTx, Data Direction Register – DDRx, and the Port Input Pins – PINx. The Port Input Pins I/O location is read only, while the Data Register and the Data Direction Register are read/write. In addition, the Pull-up Disable – PUD bit in SFIOR disables the pull-up function for all pins in all ports when set. Using the I/O port as General Digital I/O is described in “Ports as General Digital I/O” on page 52. Most port pins are multiplexed with alternate functions for the peripheral fea- tures on the device. How each alternate function interferes with the port pin is described in “Alternate Port Functions” on page 57. Refer to the individual module sections for a full description of the alternate functions. Note that enabling the alternate function of some of the port pins does not affect the use of the other pins in the port as general digital I/O. 51 2502K–AVR–10/06
Ports as General Digital The ports are bi-directional I/O ports with optional internal pull-ups. Figure 23 shows a I/O functional description of one I/O-port pin, here generically called Pxn. Figure 23. General Digital I/O(1) PUD Q D DDxn QCLR WDx RESET RDx S U B Pxn PQORTxDn TA QCLR WPx DA RESET SLEEP RRx SYNCHRONIZER RPx D Q D Q PINxn L Q Q clk I/O WDx: WRITE DDRx PUD: PULLUP DISABLE RDx: READ DDRx SLEEP: SLEEP CONTROL WPx: WRITE PORTx clk : I/O CLOCK RRx: READ PORTx REGISTER I/O RPx: READ PORTx PIN Note: 1. WPx, WDx, RRx, RPx, and RDx are common to all pins within the same port. clk , I/O SLEEP, and PUD are common to all ports. Configuring the Pin Each port pin consists of three register bits: DDxn, PORTxn, and PINxn. As shown in “Register Description for I/O-Ports” on page 66, the DDxn bits are accessed at the DDRx I/O address, the PORTxn bits at the PORTx I/O address, and the PINxn bits at the PINx I/O address. The DDxn bit in the DDRx Register selects the direction of this pin. If DDxn is written logic one, Pxn is configured as an output pin. If DDxn is written logic zero, Pxn is config- ured as an input pin. If PORTxn is written a logic one when the pin is configured as an input pin, the pull-up resistor is activated. To switch the pull-up resistor off, PORTxn has to be written logic zero or the pin has to be configured as an output pin. The port pins are tri-stated when a reset condition becomes active, even if no clocks are running. If PORTxn is written a logic one when the pin is configured as an output pin, the port pin is driven high (one). If PORTxn is written a logic zero when the pin is configured as an output pin, the port pin is driven low (zero). When switching between tri-state ({DDxn, PORTxn} = 0b00) and output high ({DDxn, PORTxn} = 0b11), an intermediate state with either pull-up enabled ({DDxn, PORTxn} = ATmega8535(L) 52 2502K–AVR–10/06
ATmega8535(L) 0b01) or output low ({DDxn, PORTxn} = 0b10) must occur. Normally, the pull-up enabled state is fully acceptable, as a high-impedant environment will not notice the dif- ference between a strong high driver and a pull-up. If this is not the case, the PUD bit in the SFIOR Register can be set to disable all pull-ups in all ports. Switching between input with pull-up and output low generates the same problem. The user must use either the tri-state ({DDxn, PORTxn} = 0b00) or the output high state ({DDxn, PORTxn} = 0b10) as an intermediate step. Table 21 summarizes the control signals for the pin value. Table 21. Port Pin Configurations PUD DDxn PORTxn (in SFIOR) I/O Pull-up Comment 0 0 X Input No Tri-state (Hi-Z) Pxn will source current if ext. pulled 0 1 0 Input Yes low. 0 1 1 Input No Tri-state (Hi-Z) 1 0 X Output No Output Low (Sink) 1 1 X Output No Output High (Source) Reading the Pin Value Independent of the setting of Data Direction bit DDxn, the port pin can be read through the PINxn Register bit. As shown in Figure 23, the PINxn Register bit and the preceding latch constitute a synchronizer. This is needed to avoid metastability if the physical pin changes value near the edge of the internal clock, but it also introduces a delay. Figure 24 shows a timing diagram of the synchronization when reading an externally applied pin value. The maximum and minimum propagation delays are denoted t and t pd,max pd,min respectively. Figure 24. Synchronization when Reading an Externally Applied Pin Value SYSTEM CLK INSTRUCTIONS XXX XXX in r17, PINx SYNC LATCH PINxn r17 0x00 0xFF t pd, max tpd, min Consider the clock period starting shortly after the first falling edge of the system clock. The latch is closed when the clock is low, and goes transparent when the clock is high, as indicated by the shaded region of the “SYNC LATCH” signal. The signal value is latched when the system clock goes low. It is clocked into the PINxn Register at the suc- 53 2502K–AVR–10/06
ceeding positive clock edge. As indicated by the two arrows t and t , a single pd,max pd,min signal transition on the pin will be delayed between ½ and 1½ system clock period depending upon the time of assertion. When reading back a software assigned pin value, a nop instruction must be inserted as indicated in Figure 25. The out instruction sets the “SYNC LATCH” signal at the positive edge of the clock. In this case, the delay t through the synchronizer is one system pd clock period. Figure 25. Synchronization when Reading a Software Assigned Pin Value SYSTEM CLK r16 0xFF INSTRUCTIONS out PORTx, r16 nop in r17, PINx SYNC LATCH PINxn r17 0x00 0xFF t pd ATmega8535(L) 54 2502K–AVR–10/06
ATmega8535(L) The following code example shows how to set port B pins 0 and 1 high, 2 and 3 low, and define the port pins from 4 to 7 as input with pull-ups assigned to port pins 6 and 7. The resulting pin values are read back again, but as previously discussed, a nop instruction is included to be able to read back the value recently assigned to some of the pins. Assembly Code Example(1) ... ; Define pull-ups and set outputs high ; Define directions for port pins ldi r16,(1<<PB7)|(1<<PB6)|(1<<PB1)|(1<<PB0) ldi r17,(1<<DDB3)|(1<<DDB2)|(1<<DDB1)|(1<<DDB0) out PORTB,r16 out DDRB,r17 ; Insert nop for synchronization nop ; Read port pins in r16,PINB ... C Code Example unsigned char i; ... /* Define pull-ups and set outputs high */ /* Define directions for port pins */ PORTB = (1<<PB7)|(1<<PB6)|(1<<PB1)|(1<<PB0); DDRB = (1<<DDB3)|(1<<DDB2)|(1<<DDB1)|(1<<DDB0); /* Insert nop for synchronization*/ _NOP(); /* Read port pins */ i = PINB; ... Note: 1. For the assembly program, two temporary registers are used to minimize the time from pull-ups are set on pins 0, 1, 6, and 7, until the direction bits are correctly set, defining bits 2 and 3 as low and redefining bits 0 and 1 as strong high drivers. Digital Input Enable and Sleep As shown in Figure 23, the digital input signal can be clamped to ground at the input of Modes the Schmitt Trigger. The signal denoted SLEEP in the figure, is set by the MCU sleep controller in Power-down mode, Power-save mode, Standby mode, and Extended Standby mode to avoid high power consumption if some input signals are left floating, or have an analog signal level close to V /2. CC SLEEP is overridden for port pins enabled as External Interrupt pins. If the External Interrupt Request is not enabled, SLEEP is active also for these pins. SLEEP is also overridden by various other alternate functions as described in “Alternate Port Func- tions” on page 57. If a logic high level (“one”) is present on an Asynchronous External Interrupt pin config- ured as “Interrupt on Rising Edge, Falling Edge, or Any Logic Change on Pin” while the external interrupt is not enabled, the corresponding External Interrupt Flag will be set 55 2502K–AVR–10/06
when resuming from the above mentioned sleep modes, as the clamping in these sleep modes produces the requested logic change. Unconnected pins If some pins are unused, it is recommended to ensure that these pins have a defined level. Even though most of the digital inputs are disabled in the deep sleep modes as described above, floating inputs should be avoided to reduce current consumption in all other modes where the digital inputs are enabled (Reset, Active mode and Idle mode). The simplest method to ensure a defined level of an unused pin, is to enable the internal pull-up. In this case, the pull-up will be disabled during reset. If low power consumption during reset is important, it is recommended to use an external pull-up or pull-down. Connecting unused pins directly to V or GND is not recommended, since this may CC cause excessive currents if the pin is accidentally configured as an output. ATmega8535(L) 56 2502K–AVR–10/06
ATmega8535(L) Alternate Port Functions Most port pins have alternate functions in addition to being general digital I/Os. Figure 26 shows how the port pin control signals from the simplified Figure 23 can be overrid- den by alternate functions. The overriding signals may not be present in all port pins, but the figure serves as a generic description applicable to all port pins in the AVR micro- controller family. Figure 26. Alternate Port Functions(1) PUOExn PUOVxn 1 PUD 0 DDOExn DDOVxn 1 0 Q D DDxn QCLR WDx PVOExn RESET PVOVxn RDx S 1 U Pxn B 0 Q D A PORTxn T DIEOExn QCLR DA WPx DIEOVxn RESET 1 RRx 0 SLEEP SYNCHRONIZER RPx DSETQ D Q PINxn LCLRQ CLRQ clkI/O DIxn AIOxn PUOExn: Pxn PULL-UP OVERRIDE ENABLE PUD: PULLUP DISABLE PUOVxn: Pxn PULL-UP OVERRIDE VALUE WDx: WRITE DDRx DDOExn: Pxn DATA DIRECTION OVERRIDE ENABLE RDx: READ DDRx DDOVxn: Pxn DATA DIRECTION OVERRIDE VALUE RRx: READ PORTx REGISTER PVOExn: Pxn PORT VALUE OVERRIDE ENABLE WPx: WRITE PORTx PVOVxn: Pxn PORT VALUE OVERRIDE VALUE RPx: READ PORTx PIN DIEOExn: Pxn DIGITAL INPUT-ENABLE OVERRIDE ENABLE clk : I/O CLOCK DIEOVxn: Pxn DIGITAL INPUT-ENABLE OVERRIDE VALUE DIxI/nO: DIGITAL INPUT PIN n ON PORTx SLEEP: SLEEP CONTROL AIOxn: ANALOG INPUT/OUTPUT PIN n ON PORTx Note: 1. WPx, WDx, RRx, RPx, and RDx are common to all pins within the same port. clk , I/O SLEEP, and PUD are common to all ports. All other signals are unique for each pin. 57 2502K–AVR–10/06
Table 22 summarizes the function of the overriding signals. The pin and port indexes from Figure 26 are not shown in the succeeding tables. The overriding signals are gen- erated internally in the modules having the alternate function. Table 22. Generic Description of Overriding Signals for Alternate Functions Signal Name Full Name Description PUOE Pull-up Override If this signal is set, the pull-up enable is controlled by the PUOV Enable signal. If this signal is cleared, the pull-up is enabled when {DDxn, PORTxn, PUD} = 0b010. PUOV Pull-up Override If PUOE is set, the pull-up is enabled/disabled when PUOV is Value set/cleared, regardless of the setting of the DDxn, PORTxn, and PUD Register bits. DDOE Data Direction If this signal is set, the Output Driver Enable is controlled by the Override Enable DDOV signal. If this signal is cleared, the Output driver is enabled by the DDxn Register bit. DDOV Data Direction If DDOE is set, the Output Driver is enabled/disabled when Override Value DDOV is set/cleared, regardless of the setting of the DDxn Register bit. PVOE Port Value If this signal is set and the Output Driver is enabled, the port Override Enable value is controlled by the PVOV signal. If PVOE is cleared, and the Output Driver is enabled, the port Value is controlled by the PORTxn Register bit. PVOV Port Value If PVOE is set, the port value is set to PVOV, regardless of the Override Value setting of the PORTxn Register bit. DIEOE Digital Input If this bit is set, the Digital Input Enable is controlled by the Enable Override DIEOV signal. If this signal is cleared, the Digital Input Enable Enable is determined by MCU-state (Normal mode, sleep modes). DIEOV Digital Input If DIEOE is set, the Digital Input is enabled/disabled when Enable Override DIEOV is set/cleared, regardless of the MCU state (Normal Value mode, sleep modes). DI Digital Input This is the Digital Input to alternate functions. In the figure, the signal is connected to the output of the schmitt trigger but before the synchronizer. Unless the Digital Input is used as a clock source, the module with the alternate function will use its own synchronizer. AIO Analog This is the Analog Input/Output to/from alternate functions. The Input/output signal is connected directly to the pad, and can be used bi- directionally. The following subsections shortly describe the alternate functions for each port, and relate the overriding signals to the alternate function. Refer to the alternate function description for further details. ATmega8535(L) 58 2502K–AVR–10/06
ATmega8535(L) Special Function IO Register – SFIOR Bit 7 6 5 4 3 2 1 0 ADTS2 ADTS1 ADTS0 – ACME PUD PSR2 PSR10 SFIOR Read/Write R/W R/W R/W R R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 2 – PUD: Pull-up disable When this bit is written to one, the pull-ups in the I/O ports are disabled even if the DDxn and PORTxn Registers are configured to enable the pull-ups ({DDxn, PORTxn} = 0b01). See “Configuring the Pin” on page 52 for more details about this feature. Alternate Functions of Port A Port A has an alternate function as analog input for the ADC as shown in Table 23. If some Port A pins are configured as outputs, it is essential that these do not switch when a conversion is in progress. This might corrupt the result of the conversion. Table 23. Port A Pins Alternate Functions Port Pin Alternate Function PA7 ADC7 (ADC input channel 7) PA6 ADC6 (ADC input channel 6) PA5 ADC5 (ADC input channel 5) PA4 ADC4 (ADC input channel 4) PA3 ADC3 (ADC input channel 3) PA2 ADC2 (ADC input channel 2) PA1 ADC1 (ADC input channel 1) PA0 ADC0 (ADC input channel 0) Table 24 and Table 25 relate the alternate functions of Port A to the overriding signals shown in Figure 26 on page 57. Table 24. Overriding Signals for Alternate Functions in PA7..PA4 Signal Name PA7/ADC7 PA6/ADC6 PA5/ADC5 PA4/ADC4 PUOE 0 0 0 0 PUOV 0 0 0 0 DDOE 0 0 0 0 DDOV 0 0 0 0 PVOE 0 0 0 0 PVOV 0 0 0 0 DIEOE 0 0 0 0 DIEOV 0 0 0 0 DI – – – – AIO ADC7 INPUT ADC6 INPUT ADC5 INPUT ADC4 INPUT 59 2502K–AVR–10/06
Table 25. Overriding Signals for Alternate Functions in PA3..PA0 Signal Name PA3/ADC3 PA2/ADC2 PA1/ADC1 PA0/ADC0 PUOE 0 0 0 0 PUOV 0 0 0 0 DDOE 0 0 0 0 DDOV 0 0 0 0 PVOE 0 0 0 0 PVOV 0 0 0 0 DIEOE 0 0 0 0 DIEOV 0 0 0 0 DI – – – – AIO ADC3 INPUT ADC2 INPUT ADC1 INPUT ADC0 INPUT Alternate Functions Of Port B The Port B pins with alternate functions are shown in Table 26. Table 26. Port B Pins Alternate Functions Port Pin Alternate Functions PB7 SCK (SPI Bus Serial Clock) PB6 MISO (SPI Bus Master Input/Slave Output) PB5 MOSI (SPI Bus Master Output/Slave Input) PB4 SS (SPI Slave Select Input) AIN1 (Analog Comparator Negative Input) PB3 OC0 (Timer/Counter0 Output Compare Match Output) AIN0 (Analog Comparator Positive Input) PB2 INT2 (External Interrupt 2 Input) PB1 T1 (Timer/Counter1 External Counter Input) T0 (Timer/Counter0 External Counter Input) PB0 XCK (USART External Clock Input/Output) The alternate pin configuration is as follows: (cid:129) SCK – Port B, Bit 7 SCK: Master Clock output, Slave Clock input pin for SPI channel. When the SPI is enabled as a Slave, this pin is configured as an input regardless of the setting of DDB7. When the SPI is enabled as a Master, the data direction of this pin is controlled by DDB7. When the pin is forced by the SPI to be an input, the pull-up can still be con- trolled by the PORTB7 bit. (cid:129) MISO – Port B, Bit 6 MISO: Master Data input, Slave Data output pin for SPI channel. When the SPI is enabled as a Master, this pin is configured as an input regardless of the setting of DDB6. When the SPI is enabled as a Slave, the data direction of this pin is controlled by DDB6. When the pin is forced by the SPI to be an input, the pull-up can still be con- trolled by the PORTB6 bit. ATmega8535(L) 60 2502K–AVR–10/06
ATmega8535(L) (cid:129) MOSI – Port B, Bit 5 MOSI: SPI Master Data output, Slave Data input for SPI channel. When the SPI is enabled as a Slave, this pin is configured as an input regardless of the setting of DDB5. When the SPI is enabled as a Master, the data direction of this pin is controlled by DDB5. When the pin is forced by the SPI to be an input, the pull-up can still be con- trolled by the PORTB5 bit. (cid:129) SS – Port B, Bit 4 SS: Slave Select input. When the SPI is enabled as a Slave, this pin is configured as an input regardless of the setting of DDB4. As a Slave, the SPI is activated when this pin is driven low. When the SPI is enabled as a Master, the data direction of this pin is con- trolled by DDB4. When the pin is forced by the SPI to be an input, the pull-up can still be controlled by the PORTB4 bit. (cid:129) AIN1/OC0 – Port B, Bit 3 AIN1, Analog Comparator Negative input. Configure the port pin as input with the inter- nal pull-up switched off to avoid the digital port function from interfering with the function of the Analog Comparator. OC0, Output Compare Match output: The PB3 pin can serve as an external output for the Timer/Counter0 Compare Match. The PB3 pin has to be configured as an output (DDB3 set (one)) to serve this function. The OC0 pin is also the output pin for the PWM mode timer function. (cid:129) AIN0/INT2 – Port B, Bit 2 AIN0, Analog Comparator Positive input. Configure the port pin as input with the internal pull-up switched off to avoid the digital port function from interfering with the function of the Analog Comparator. INT2, External Interrupt Source 2: The PB2 pin can serve as an external interrupt source to the MCU. (cid:129) T1 – Port B, Bit 1 T1, Timer/Counter1 Counter Source. (cid:129) T0/XCK – Port B, Bit 0 T0, Timer/Counter0 Counter Source. XCK, USART External Clock. The Data Direction Register (DDB0) controls whether the clock is output (DDB0 set) or input (DDB0 cleared). The XCK pin is active only when the USART operates in synchronous mode. Table 27 and Table 28 relate the alternate functions of Port B to the overriding signals shown in Figure 26 on page 57. SPI MSTR INPUT and SPI SLAVE OUTPUT constitute the MISO signal, while MOSI is divided into SPI MSTR OUTPUT and SPI SLAVE INPUT. 61 2502K–AVR–10/06
Table 27. Overriding Signals for Alternate Functions in PB7..PB4 Signal Name PB7/SCK PB6/MISO PB5/MOSI PB4/SS PUOE SPE (cid:129) MSTR SPE (cid:129) MSTR SPE (cid:129) MSTR SPE (cid:129) MSTR PUOV PORTB7 (cid:129) PUD PORTB6 (cid:129) PUD PORTB5 (cid:129) PUD PORTB4 (cid:129) PUD DDOE SPE (cid:129) MSTR SPE (cid:129) MSTR SPE (cid:129) MSTR SPE (cid:129) MSTR DDOV 0 0 0 0 PVOE SPE (cid:129) MSTR SPE (cid:129) MSTR SPE (cid:129) MSTR 0 PVOV SCK OUTPUT SPI SLAVE OUTPUT SPI MSTR OUTPUT 0 DIEOE 0 0 0 0 DIEOV 0 0 0 0 DI SCK INPUT SPI MSTR INPUT SPI SLAVE INPUT SPI SS AIO – – – – Table 28. Overriding Signals for Alternate Functions in PB3..PB0 Signal Name PB3/OC0/AIN1 PB2/INT2/AIN0 PB1/T1 PB0/T0/XCK PUOE 0 0 0 0 PUOV 0 0 0 0 DDOE 0 0 0 0 DDOV 0 0 0 0 PVOE OC0 ENABLE 0 0 UMSEL PVOV OC0 0 0 XCK OUTPUT DIEOE 0 INT2 ENABLE 0 0 DIEOV 0 1 0 0 DI – INT2 INPUT T1 INPUT XCK INPUT/ T0 INPUT AIO AIN1 INPUT AIN0 INPUT – – Alternate Functions of Port C The Port C pins with alternate functions are shown in Table 29. Table 29. Port C Pins Alternate Functions Port Pin Alternate Function PC7 TOSC2 (Timer Oscillator Pin 2) PC6 TOSC1 (Timer Oscillator Pin 1) PC1 SDA (Two-wire Serial Bus Data Input/Output Line) PC0 SCL (Two-wire Serial Bus Clock Line) The alternate pin configuration is as follows: (cid:129) TOSC2 – Port C, Bit 7 ATmega8535(L) 62 2502K–AVR–10/06
ATmega8535(L) TOSC2, Timer Oscillator pin 2: When the AS2 bit in ASSR is set (one) to enable asyn- chronous clocking of Timer/Counter2, pin PC7 is disconnected from the port, and becomes the inverting output of the Oscillator amplifier. In this mode, a crystal Oscillator is connected to this pin, and the pin can not be used as an I/O pin. (cid:129) TOSC1 – Port C, Bit 6 TOSC1, Timer Oscillator pin 1: When the AS2 bit in ASSR is set (one) to enable asyn- chronous clocking of Timer/Counter2, pin PC6 is disconnected from the port, and becomes the input of the inverting Oscillator amplifier. In this mode, a crystal Oscillator is connected to this pin, and the pin can not be used as an I/O pin. (cid:129) SDA – Port C, Bit 1 SDA, Two-wire Serial Interface Data: When the TWEN bit in TWCR is set (one) to enable the Two-wire Serial Interface, pin PC1 is disconnected from the port and becomes the Serial Data I/O pin for the Two-wire Serial Interface. In this mode, there is a spike filter on the pin to suppress spikes shorter than 50 ns on the input signal, and the pin is driven by an open drain driver with slew-rate limitation. When this pin is used by the Two-wire Serial Interface, the pull-up can still be controlled by the PORTC1 bit. (cid:129) SCL – Port C, Bit 0 SCL, Two-wire Serial Interface Clock: When the TWEN bit in TWCR is set (one) to enable the Two-wire Serial Interface, pin PC0 is disconnected from the port and becomes the Serial Clock I/O pin for the Two-wire Serial Interface. In this mode, there is a spike filter on the pin to suppress spikes shorter than 50 ns on the input signal, and the pin is driven by an open drain driver with slew-rate limitation. When this pin is used by the Two-wire Serial Interface, the pull-up can still be controlled by the PORTC0 bit. Table 30 and Table 31 relate the alternate functions of Port C to the overriding signals shown in Figure 26 on page 57. Table 30. Overriding Signals for Alternate Functions in PC7..PC6 Signal Name PC7/TOSC2 PC6/TOSC1 PUOE AS2 AS2 PUOV 0 0 DDOE AS2 AS2 DDOV 0 0 PVOE 0 0 PVOV 0 0 DIEOE AS2 AS2 DIEOV 0 0 DI – – AIO T/C2 OSC OUTPUT T/C2 OSC INPUT 63 2502K–AVR–10/06
Table 31. Overriding Signals for Alternate Functions in PC1..PC0(1) Signal Name PC1/SDA PC0/SCL PUOE TWEN TWEN PUOV PORTC1 (cid:129) PUD PORTC0 (cid:129) PUD DDOE TWEN TWEN DDOV SDA_OUT SCL_OUT PVOE TWEN TWEN PVOV 0 0 DIEOE 0 0 DIEOV 0 0 DI – – AIO SDA INPUT SCL INPUT Note: 1. When enabled, the Two-wire Serial Interface enables slew-rate controls on the output pins PC0 and PC1. This is not shown in the figure. In addition, spike filters are con- nected between the AIO outputs shown in the port figure and the digital logic of the TWI module. Alternate Functions of Port D The Port D pins with alternate functions are shown in Table 32. Table 32. Port D Pins Alternate Functions Port Pin Alternate Function PD7 OC2 (Timer/Counter2 Output Compare Match Output) PD6 ICP1 (Timer/Counter1 Input Capture Pin) PD5 OC1A (Timer/Counter1 Output Compare A Match Output) PD4 OC1B (Timer/Counter1 Output Compare B Match Output) PD3 INT1 (External Interrupt 1 Input) PD2 INT0 (External Interrupt 0 Input) PD1 TXD (USART Output Pin) PD0 RXD (USART Input Pin) The alternate pin configuration is as follows: (cid:129) OC2 – Port D, Bit 7 OC2, Timer/Counter2 Output Compare Match output: The PD7 pin can serve as an external output for the Timer/Counter2 Output Compare. The pin has to be configured as an output (DDD7 set (one)) to serve this function. The OC2 pin is also the output pin for the PWM mode timer function. (cid:129) ICP1 – Port D, Bit 6 ICP1 – Input Capture Pin: The PD6 pin can act as an Input Capture pin for Timer/Counter1. (cid:129) OC1A – Port D, Bit 5 OC1A, Output Compare Match A output: The PD5 pin can serve as an external output for the Timer/Counter1 Output Compare A. The pin has to be configured as an output ATmega8535(L) 64 2502K–AVR–10/06
ATmega8535(L) (DDD5 set (one)) to serve this function. The OC1A pin is also the output pin for the PWM mode timer function. (cid:129) OC1B – Port D, Bit 4 OC1B, Output Compare Match B output: The PD4 pin can serve as an external output for the Timer/Counter1 Output Compare B. The pin has to be configured as an output (DDD4 set (one)) to serve this function. The OC1B pin is also the output pin for the PWM mode timer function. (cid:129) INT1 – Port D, Bit 3 INT1, External Interrupt Source 1: The PD3 pin can serve as an external interrupt source. (cid:129) INT0 – Port D, Bit 2 INT0, External Interrupt Source 0: The PD2 pin can serve as an external interrupt source. (cid:129) TXD – Port D, Bit 1 TXD, Transmit Data (Data output pin for the USART). When the USART Transmitter is enabled, this pin is configured as an output regardless of the value of DDD1. (cid:129) RXD – Port D, Bit 0 RXD, Receive Data (Data input pin for the USART). When the USART Receiver is enabled this pin is configured as an input regardless of the value of DDD0. When the USART forces this pin to be an input, the pull-up can still be controlled by the PORTD0 bit. Table 33 and Table 34 relate the alternate functions of Port D to the overriding signals shown in Figure 26 on page 57. Table 33. Overriding Signals for Alternate Functions PD7..PD4 Signal Name PD7/OC2 PD6/ICP1 PD5/OC1A PD4/OC1B PUOE 0 0 0 0 PUOV 0 0 0 0 DDOE 0 0 0 0 DDOV 0 0 0 0 PVOE OC2 ENABLE 0 OC1A ENABLE OC1B ENABLE PVOV OC2 0 OC1A OC1B DIEOE 0 0 0 0 DIEOV 0 0 0 0 DI – ICP1 INPUT – – AIO – – – – 65 2502K–AVR–10/06
Table 34. Overriding Signals for Alternate Functions in PD3..PD0 Signal Name PD3/INT1 PD2/INT0 PD1/TXD PD0/RXD PUOE 0 0 TXEN RXEN PUOV 0 0 0 PORTD0 (cid:129) PUD DDOE 0 0 TXEN RXEN DDOV 0 0 1 0 PVOE 0 0 TXEN 0 PVOV 0 0 TXD 0 DIEOE INT1 ENABLE INT0 ENABLE 0 0 DIEOV 1 1 0 0 DI INT1 INPUT INT0 INPUT – RXD AIO – – – – Register Description for I/O-Ports Port A Data Register – PORTA Bit 7 6 5 4 3 2 1 0 PORTA7 PORTA6 PORTA5 PORTA4 PORTA3 PORTA2 PORTA1 PORTA0 PORTA Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 Port A Data Direction Register – DDRA Bit 7 6 5 4 3 2 1 0 DDA7 DDA6 DDA5 DDA4 DDA3 DDA2 DDA1 DDA0 DDRA Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 Port A Input Pins Address – PINA Bit 7 6 5 4 3 2 1 0 PINA7 PINA6 PINA5 PINA4 PINA3 PINA2 PINA1 PINA0 PINA Read/Write R R R R R R R R Initial Value N/A N/A N/A N/A N/A N/A N/A N/A Port B Data Register – PORTB Bit 7 6 5 4 3 2 1 0 PORTB7 PORTB6 PORTB5 PORTB4 PORTB3 PORTB2 PORTB1 PORTB0 PORTB Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 Port B Data Direction Register – DDRB Bit 7 6 5 4 3 2 1 0 DDB7 DDB6 DDB5 DDB4 DDB3 DDB2 DDB1 DDB0 DDRB Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 ATmega8535(L) 66 2502K–AVR–10/06
ATmega8535(L) Port B Input Pins Address – PINB Bit 7 6 5 4 3 2 1 0 PINB7 PINB6 PINB5 PINB4 PINB3 PINB2 PINB1 PINB0 PINB Read/Write R R R R R R R R Initial Value N/A N/A N/A N/A N/A N/A N/A N/A Port C Data Register – PORTC Bit 7 6 5 4 3 2 1 0 PORTC7 PORTC6 PORTC5 PORTC4 PORTC3 PORTC2 PORTC1 PORTC0 PORTC Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 Port C Data Direction Register – DDRC Bit 7 6 5 4 3 2 1 0 DDC7 DDC6 DDC5 DDC4 DDC3 DDC2 DDC1 DDC0 DDRC Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 Port C Input Pins Address – PINC Bit 7 6 5 4 3 2 1 0 PINC7 PINC6 PINC5 PINC4 PINC3 PINC2 PINC1 PINC0 PINC Read/Write R R R R R R R R Initial Value N/A N/A N/A N/A N/A N/A N/A N/A Port D Data Register – PORTD Bit 7 6 5 4 3 2 1 0 PORTD7 PORTD6 PORTD5 PORTD4 PORTD3 PORTD2 PORTD1 PORTD0 PORTD Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 Port D Data Direction Register – DDRD Bit 7 6 5 4 3 2 1 0 DDD7 DDD6 DDD5 DDD4 DDD3 DDD2 DDD1 DDD0 DDRD Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 Port D Input Pins Address – PIND Bit 7 6 5 4 3 2 1 0 PIND7 PIND6 PIND5 PIND4 PIND3 PIND2 PIND1 PIND0 PIND Read/Write R R R R R R R R Initial Value N/A N/A N/A N/A N/A N/A N/A N/A 67 2502K–AVR–10/06
External Interrupts The External Interrupts are triggered by the INT0, INT1, and INT2 pins. Observe that, if enabled, the interrupts will trigger even if the INT0..2 pins are configured as outputs. This feature provides a way of generating a software interrupt. The External Interrupts can be triggered by a falling or rising edge or a low level (INT2 is only an edge triggered interrupt). This is set up as indicated in the specification for the MCU Control Register – MCUCR and MCU Control and Status Register – MCUCSR. When the External Inter- rupt is enabled and is configured as level triggered (only INT0/INT1), the interrupt will trigger as long as the pin is held low. Note that recognition of falling or rising edge inter- rupts on INT0 and INT1 requires the presence of an I/O clock, described in “Clock Systems and their Distribution” on page 24. Low level interrupts on INT0/INT1 and the edge interrupt on INT2 are detected asynchronously. This implies that these interrupts can be used for waking the part also from sleep modes other than Idle mode. The I/O clock is halted in all sleep modes except Idle mode. Note that if a level triggered interrupt is used for wake-up from Power-down mode, the changed level must be held for some time to wake up the MCU. This makes the MCU less sensitive to noise. The changed level is sampled twice by the Watchdog Oscillator clock. The period of the Watchdog Oscillator is 1 µs (nominal) at 5.0V and 25°C. The frequency of the Watchdog Oscillator is voltage dependent as shown in “Electrical Char- acteristics” on page 255. The MCU will wake up if the input has the required level during this sampling or if it is held until the end of the start-up time. The start-up time is defined by the SUT Fuses as described in “System Clock and Clock Options” on page 24. If the level is sampled twice by the Watchdog Oscillator clock but disappears before the end of the start-up time, the MCU will still wake up, but no interrupt will be generated. The required level must be held long enough for the MCU to complete the wake up to trigger the level interrupt. MCU Control Register – The MCU Control Register contains control bits for interrupt sense control and general MCUCR MCU functions. Bit 7 6 5 4 3 2 1 0 SM2 SE SM1 SM0 ISC11 ISC10 ISC01 ISC00 MCUCR Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 3, 2 – ISC11, ISC10: Interrupt Sense Control 1 Bit 1 and Bit 0 The External Interrupt 1 is activated by the external pin INT1 if the SREG I-bit and the corresponding interrupt mask in the GICR are set. The level and edges on the external INT1 pin that activate the interrupt are defined in Table 35. The value on the INT1 pin is sampled before detecting edges. If edge or toggle interrupt is selected, pulses that last longer than one clock period will generate an interrupt. Shorter pulses are not guaran- teed to generate an interrupt. If low level interrupt is selected, the low level must be held until the completion of the currently executing instruction to generate an interrupt. Table 35. Interrupt 1 Sense Control ISC11 ISC10 Description 0 0 The low level of INT1 generates an interrupt request. 0 1 Any logical change on INT1 generates an interrupt request. 1 0 The falling edge of INT1 generates an interrupt request. 1 1 The rising edge of INT1 generates an interrupt request. (cid:129) Bit 1, 0 – ISC01, ISC00: Interrupt Sense Control 0 Bit 1 and Bit 0 ATmega8535(L) 68 2502K–AVR–10/06
ATmega8535(L) The External Interrupt 0 is activated by the external pin INT0 if the SREG I-flag and the corresponding interrupt mask are set. The level and edges on the external INT0 pin that activate the interrupt are defined in Table 36. The value on the INT0 pin is sampled before detecting edges. If edge or toggle interrupt is selected, pulses that last longer than one clock period will generate an interrupt. Shorter pulses are not guaranteed to generate an interrupt. If low level interrupt is selected, the low level must be held until the completion of the currently executing instruction to generate an interrupt. Table 36. Interrupt 0 Sense Control ISC01 ISC00 Description 0 0 The low level of INT0 generates an interrupt request. 0 1 Any logical change on INT0 generates an interrupt request. 1 0 The falling edge of INT0 generates an interrupt request. 1 1 The rising edge of INT0 generates an interrupt request. MCU Control and Status Register – MCUCSR Bit 7 6 5 4 3 2 1 0 – ISC2 – – WDRF BORF EXTRF PORF MCUCSR Read/Write R/W R/W R R/W R/W R/W R/W R/W Initial Value 0 0 0 See Bit Description (cid:129) Bit 6 – ISC2: Interrupt Sense Control 2 The asynchronous External Interrupt 2 is activated by the external pin INT2 if the SREG I-bit and the corresponding interrupt mask in GICR are set. If ISC2 is written to zero, a falling edge on INT2 activates the interrupt. If ISC2 is written to one, a rising edge on INT2 activates the interrupt. Edges on INT2 are registered asynchronously. Pulses on INT2 wider than the minimum pulse width given in Table 37 will generate an interrupt. Shorter pulses are not guaranteed to generate an interrupt. When changing the ISC2 bit, an interrupt can occur. Therefore, it is recommended to first disable INT2 by clearing its Interrupt Enable bit in the GICR Register. Then, the ISC2 bit can be changed. Finally, the INT2 Interrupt Flag should be cleared by writing a logical one to its Interrupt Flag bit (INTF2) in the GIFR Register before the interrupt is re-enabled. Table 37. Asynchronous External Interrupt Characteristics Symbol Parameter Min Typ Max Units Minimum pulse width for asynchronous external t 50 ns INT interrupt General Interrupt Control Register – GICR Bit 7 6 5 4 3 2 1 0 INT1 INT0 INT2 – – – IVSEL IVCE GICR Read/Write R/W R/W R/W R R R R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 7 – INT1: External Interrupt Request 1 Enable When the INT1 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), the external pin interrupt is enabled. The Interrupt Sense Control1 bits 1/0 (ISC11 and ISC10) in the MCU General Control Register (MCUCR) define whether the external interrupt is activated on the rising and/or falling edge of the INT1 pin or level sensed. Activity on the pin will cause an interrupt request even if INT1 is configured as an output. 69 2502K–AVR–10/06
The corresponding interrupt of External Interrupt Request 1 is executed from the INT1 Interrupt Vector. (cid:129) Bit 6 – INT0: External Interrupt Request 0 Enable When the INT0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), the external pin interrupt is enabled. The Interrupt Sense Control0 bits 1/0 (ISC01 and ISC00) in the MCU General Control Register (MCUCR) define whether the external interrupt is activated on rising and/or falling edge of the INT0 pin or level sensed. Activity on the pin will cause an interrupt request even if INT0 is configured as an output. The corresponding interrupt of External Interrupt Request 0 is executed from the INT0 Inter- rupt Vector. (cid:129) Bit 5 – INT2: External Interrupt Request 2 Enable When the INT2 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), the external pin interrupt is enabled. The Interrupt Sense Control2 bit (ISC2) in the MCU Control and Status Register (MCUCSR) defines whether the external interrupt is acti- vated on the rising or falling edge of the INT2 pin. Activity on the pin will cause an interrupt request even if INT2 is configured as an output. The corresponding interrupt of External Interrupt Request 2 is executed from the INT2 Interrupt Vector. General Interrupt Flag Register – GIFR Bit 7 6 5 4 3 2 1 0 INTF1 INTF0 INTF2 – – – – – GIFR Read/Write R/W R/W R/W R R R R R Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 7 – INTF1: External Interrupt Flag 1 When an edge or logic change on the INT1 pin triggers an interrupt request, INTF1 becomes set (one). If the I-bit in SREG and the INT1 bit in GICR are set (one), the MCU will jump to the corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to it. This flag is always cleared when INT1 is configured as a level interrupt. (cid:129) Bit 6 – INTF0: External Interrupt Flag 0 When an edge or logic change on the INT0 pin triggers an interrupt request, INTF0 becomes set (one). If the I-bit in SREG and the INT0 bit in GICR are set (one), the MCU will jump to the corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to it. This flag is always cleared when INT0 is configured as a level interrupt. (cid:129) Bit 5 – INTF2: External Interrupt Flag 2 When an event on the INT2 pin triggers an interrupt request, INTF2 becomes set (one). If the I-bit in SREG and the INT2 bit in GICR are set (one), the MCU will jump to the cor- responding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to it. Note that when enter- ing some sleep modes with the INT2 interrupt disabled, the input buffer on this pin will be disabled. This may cause a logic change in internal signals which will set the INTF2 Flag. See “Digital Input Enable and Sleep Modes” on page 55 for more information. ATmega8535(L) 70 2502K–AVR–10/06
ATmega8535(L) 8-bit Timer/Counter0 Timer/Counter0 is a general purpose, single channel, 8-bit Timer/Counter module. The with PWM main features are: (cid:129) Single Channel Counter (cid:129) Clear Timer on Compare Match (Auto Reload) (cid:129) Glitch-free, Phase Correct Pulse Width Modulator (PWM) (cid:129) Frequency Generator (cid:129) External Event Counter (cid:129) 10-bit Clock Prescaler (cid:129) Overflow and Compare Match Interrupt Sources (TOV0 and OCF0) Overview A simplified block diagram of the 8-bit Timer/Counter is shown in Figure 27. For the actual placement of I/O pins, refer to “Pinout ATmega8535” on page 2. CPU accessible I/O Registers, including I/O bits and I/O pins, are shown in bold. The device-specific I/O Register and bit locations are listed in the “8-bit Timer/Counter Register Description” on page 83. Figure 27. 8-bit Timer/Counter Block Diagram TCCRn count TOVn clear (Int.Req.) Control Logic direction clkTn Clock Select Edge Tn Detector BOTTOM TOP S ( From Prescaler ) U Timer/Counter B TCNTn A = 0 = 0xFF T OCn A (Int.Req.) D = Waveform OCn Generation OCRn Registers The Timer/Counter (TCNT0) and Output Compare Register (OCR0) are 8-bit registers. Interrupt request (abbreviated to Int.Req. in the figure) signals are all visible in the Timer Interrupt Flag Register (TIFR). All interrupts are individually masked with the Timer Interrupt Mask Register (TIMSK). TIFR and TIMSK are not shown in the figure since these registers are shared by other timer units. The Timer/Counter can be clocked internally, via the prescaler, or by an external clock source on the T0 pin. The Clock Select logic block controls which clock source and edge the Timer/Counter uses to increment (or decrement) its value. The Timer/Counter is inactive when no clock source is selected. The output from the Clock Select logic is referred to as the timer clock (clk ). T0 71 2502K–AVR–10/06
The double buffered Output Compare Register (OCR0) is compared with the Timer/Counter value at all times. The result of the compare can be used by the Wave- form Generator to generate a PWM or variable frequency output on the Output Compare pin (OC0). See “Output Compare Unit” on page 73. for details. The Compare Match event will also set the Compare Flag (OCF0) which can be used to generate an output compare interrupt request. Definitions Many register and bit references in this document are written in general form. A lower case “n” replaces the Timer/Counter number, in this case 0. However, when using the register or bit defines in a program, the precise form must be used, i.e., TCNT0 for accessing Timer/Counter0 counter value and so on. The definitions in Table 38 are also used extensively throughout the document. Table 38. Definitions BOTTOM The counter reaches the BOTTOM when it becomes 0x00. MAX The counter reaches its MAXimum when it becomes 0xFF (decimal 255). TOP The counter reaches the TOP when it becomes equal to the highest value in the count sequence. The TOP value can be assigned to be the fixed value 0xFF (MAX) or the value stored in the OCR0 Register. The assignment is dependent on the mode of operation. Timer/Counter Clock The Timer/Counter can be clocked by an internal or an external clock source. The clock Sources source is selected by the Clock Select logic which is controlled by the clock select (CS02:0) bits located in the Timer/Counter Control Register (TCCR0). For details on clock sources and prescaler, see “Timer/Counter0 and Timer/Counter1 Prescalers” on page 87. Counter Unit The main part of the 8-bit Timer/Counter is the programmable bi-directional counter unit. Figure 28 shows a block diagram of the counter and its surroundings. Figure 28. Counter Unit Block Diagram TOVn DATA BUS (Int.Req.) Clock Select count Edge Tn TCNTn clear Control Logic clkTn Detector direction ( From Prescaler ) bottom top Signal description (internal signals): count Increment or decrement TCNT0 by 1. direction Select between increment and decrement. clear Clear TCNT0 (set all bits to zero). clk Timer/Counter clock, referred to as clk in the following. Tn T0 ATmega8535(L) 72 2502K–AVR–10/06
ATmega8535(L) top Signalize that TCNT0 has reached maximum value. bottom Signalize that TCNT0 has reached minimum value (zero). Depending of the mode of operation used, the counter is cleared, incremented, or dec- remented at each timer clock (clk ). clk can be generated from an external or internal T0 T0 clock source, selected by the Clock Select bits (CS02:0). When no clock source is selected (CS02:0 = 0) the timer is stopped. However, the TCNT0 value can be accessed by the CPU, regardless of whether clk is present or not. A CPU write overrides (has T0 priority over) all counter clear or count operations. The counting sequence is determined by the setting of the WGM01 and WGM00 bits located in the Timer/Counter Control Register (TCCR0). There are close connections between how the counter behaves (counts) and how waveforms are generated on the output compare output OC0. For more details about advanced counting sequences and waveform generation, see “Modes of Operation” on page 76. The Timer/Counter Overflow Flag (TOV0) is set according to the mode of operation selected by the WGM01:0 bits. TOV0 can be used for generating a CPU interrupt. Output Compare Unit The 8-bit comparator continuously compares TCNT0 with the Output Compare Register (OCR0). Whenever TCNT0 equals OCR0, the comparator signals a match. A match will set the Output Compare Flag (OCF0) at the next timer clock cycle. If enabled (OCIE0 = 1 and Global Interrupt Flag in SREG is set), the Output Compare Flag generates an out- put compare interrupt. The OCF0 Flag is automatically cleared when the interrupt is executed. Alternatively, the OCF0 Flag can be cleared by software by writing a logical one to its I/O bit location. The Waveform Generator uses the match signal to generate an output according to operating mode set by the WGM01:0 bits and Compare Output mode (COM01:0) bits. The max and bottom signals are used by the Waveform Genera- tor for handling the special cases of the extreme values in some modes of operation (See “Modes of Operation” on page 76.). Figure 29 shows a block diagram of the output compare unit. Figure 29. Output Compare Unit, Block Diagram DATA BUS OCRn TCNTn = (8-bit Comparator ) OCFn (Int.Req.) top bottom Waveform Generator OCn FOCn WGMn1:0 COMn1:0 73 2502K–AVR–10/06
The OCR0 Register is double buffered when using any of the Pulse Width Modulation (PWM) modes. For the normal and Clear Timer on Compare (CTC) modes of operation, the double buffering is disabled. The double buffering synchronizes the update of the OCR0 Compare Register to either top or bottom of the counting sequence. The synchro- nization prevents the occurrence of odd-length, non-symmetrical PWM pulses, thereby making the output glitch-free. The OCR0 Register access may seem complex, but this is not the case. When the dou- ble buffering is enabled, the CPU has access to the OCR0 Buffer Register, and if double buffering is disabled the CPU will access the OCR0 directly. Force Output Compare In non-PWM waveform generation modes, the match output of the comparator can be forced by writing a one to the Force Output Compare (FOC0) bit. Forcing Compare Match will not set the OCF0 Flag or reload/clear the timer, but the OC0 pin will be updated as if a real Compare Match had occurred (the COM01:0 bits settings define whether the OC0 pin is set, cleared or toggled). Compare Match Blocking by All CPU write operations to the TCNT0 Register will block any Compare Match that TCNT0 Write occur in the next timer clock cycle, even when the timer is stopped. This feature allows OCR0 to be initialized to the same value as TCNT0 without triggering an interrupt when the Timer/Counter clock is enabled. Using the Output Compare Since writing TCNT0 in any mode of operation will block all compare matches for one Unit timer clock cycle, there are risks involved when changing TCNT0 when using the output compare channel, independently of whether the Timer/Counter is running or not. If the value written to TCNT0 equals the OCR0 value, the Compare Match will be missed, resulting in incorrect waveform generation. Similarly, do not write the TCNT0 value equal to BOTTOM when the counter is down-counting. The setup of the OC0 should be performed before setting the Data Direction Register for the port pin to output. The easiest way of setting the OC0 value is to use the force output compare (FOC0) strobe bits in normal mode. The OC0 Register keeps its value even when changing between Waveform Generation modes. Be aware that the COM01:0 bits are not double buffered together with the compare value. Changing the COM01:0 bits will take effect immediately. ATmega8535(L) 74 2502K–AVR–10/06
ATmega8535(L) Compare Match Output The Compare Output mode (COM01:0) bits have two functions. The Waveform Genera- Unit tor uses the COM01:0 bits for defining the Output Compare (OC0) state at the next Compare Match. Also, the COM01:0 bits control the OC0 pin output source. Figure 30 shows a simplified schematic of the logic affected by the COM01:0 bit setting. The I/O Registers, I/O bits, and I/O pins in the figure are shown in bold. Only the parts of the general I/O Port Control Registers (DDR and PORT) that are affected by the COM01:0 bits are shown. When referring to the OC0 state, the reference is for the internal OC0 Register, not the OC0 pin. If a System Reset occur, the OC0 Register is reset to “0”. Figure 30. Compare Match Output Unit, Schematic COMn1 Waveform COMn0 D Q Generator FOCn 1 OCn OCn Pin 0 D Q S U B PORT A T A D D Q DDR clk I/O The general I/O port function is overridden by the Output Compare (OC0) from the waveform generator if either of the COM01:0 bits are set. However, the OC0 pin direc- tion (input or output) is still controlled by the Data Direction Register (DDR) for the port pin. The Data Direction Register bit for the OC0 pin (DDR_OC0) must be set as output before the OC0 value is visible on the pin. The port override function is independent of the Waveform Generation mode. The design of the output compare pin logic allows initialization of the OC0 state before the output is enabled. Note that some COM01:0 bit settings are reserved for certain modes of operation. See “8-bit Timer/Counter Register Description” on page 83. Compare Output Mode and The Waveform Generator uses the COM01:0 bits differently in normal, CTC, and PWM Waveform Generation modes. For all modes, setting the COM01:0 = 0 tells the Waveform Generator that no action on the OC0 Register is to be performed on the next Compare Match. For com- pare output actions in the non-PWM modes refer to Table 40 on page 84. For fast PWM mode, refer to Table 41 on page 84, and for phase correct PWM refer to Table 42 on page 84. A change of the COM01:0 bits state will have effect at the first Compare Match after the bits are written. For non-PWM modes, the action can be forced to have immediate effect by using the FOC0 strobe bits. 75 2502K–AVR–10/06
Modes of Operation The mode of operation, i.e., the behavior of the Timer/Counter and the output compare pins, is defined by the combination of the Waveform Generation mode (WGM01:0) and Compare Output mode (COM01:0) bits. The Compare Output mode bits do not affect the counting sequence, while the Waveform Generation mode bits do. The COM01:0 bits control whether the PWM output generated should be inverted or not (inverted or non-inverted PWM). For non-PWM modes the COM01:0 bits control whether the output should be set, cleared, or toggled at a Compare Match (See “Compare Match Output Unit” on page 75.). For detailed timing information refer to Figure 34, Figure 35, Figure 36, and Figure 37 in “Timer/Counter Timing Diagrams” on page 80. Normal Mode The simplest mode of operation is the Normal mode (WGM01:0 = 0). In this mode the counting direction is always up (incrementing), and no counter clear is performed. The counter simply overruns when it passes its maximum 8-bit value (TOP = 0xFF) and then restarts from the bottom (0x00). In normal operation the Timer/Counter Overflow Flag (TOV0) will be set in the same timer clock cycle as the TCNT0 becomes zero. The TOV0 Flag in this case behaves like a ninth bit, except that it is only set, not cleared. However, combined with the Timer Overflow interrupt that automatically clears the TOV0 Flag, the timer resolution can be increased by software. There are no special cases to consider in the normal mode, a new counter value can be written anytime. The output compare unit can be used to generate interrupts at some given time. Using the output compare to generate waveforms in Normal mode is not recommended, since this will occupy too much of the CPU time. Clear Timer on Compare In Clear Timer on Compare or CTC mode (WGM01:0 = 2), the OCR0 Register is used to Match (CTC) Mode manipulate the counter resolution. In CTC mode the counter is cleared to zero when the counter value (TCNT0) matches the OCR0. The OCR0 defines the top value for the counter, hence also its resolution. This mode allows greater control of the Compare Match output frequency. It also simplifies the operation of counting external events. The timing diagram for the CTC mode is shown in Figure 31. The counter value (TCNT0) increases until a Compare Match occurs between TCNT0 and OCR0, and then counter (TCNT0) is cleared. Figure 31. CTC Mode, Timing Diagram OCn Interrupt Flag Set TCNTn OCn (COMn1:0 = 1) (Toggle) Period 1 2 3 4 An interrupt can be generated each time the counter value reaches the TOP value by using the OCF0 Flag. If the interrupt is enabled, the interrupt handler routine can be used for updating the TOP value. However, changing TOP to a value close to BOTTOM ATmega8535(L) 76 2502K–AVR–10/06
ATmega8535(L) when the counter is running with none or a low prescaler value must be done with care since the CTC mode does not have the double buffering feature. If the new value written to OCR0 is lower than the current value of TCNT0, the counter will miss the Compare Match. The counter will then have to count to its maximum value (0xFF) and wrap around starting at 0x00 before the Compare Match can occur. For generating a waveform output in CTC mode, the OC0 output can be set to toggle its logical level on each Compare Match by setting the Compare Output mode bits to toggle mode (COM01:0 = 1). The OC0 value will not be visible on the port pin unless the data direction for the pin is set to output. The waveform generated will have a maximum fre- quency of f = f /2 when OCR0 is set to zero (0x00). The waveform frequency is OC0 clk_I/O defined by the following equation: f clk_I/O f = ----------------------------------------------- OCn 2⋅N⋅(1+OCRn) The “N” variable represents the prescale factor (1, 8, 64, 256, or 1024). As for the normal mode of operation, the TOV0 Flag is set in the same timer clock cycle that the counter counts from MAX to 0x00. Fast PWM Mode The fast Pulse Width Modulation or fast PWM mode (WGM01:0 = 3) provides a high fre- quency PWM waveform generation option. The fast PWM differs from the other PWM option by its single-slope operation. The counter counts from BOTTOM to MAX then restarts from BOTTOM. In non-inverting Compare Output mode, the Output Compare (OC0) is cleared on the Compare Match between TCNT0 and OCR0, and set at BOT- TOM. In inverting Compare Output mode, the output is set on Compare Match and cleared at BOTTOM. Due to the single-slope operation, the operating frequency of the fast PWM mode can be twice as high as the phase correct PWM mode that use dual- slope operation. This high frequency makes the fast PWM mode well suited for power regulation, rectification, and DAC applications. High frequency allows physically small sized external components (coils, capacitors), and therefore reduces total system cost. In fast PWM mode, the counter is incremented until the counter value matches the MAX value. The counter is then cleared at the following timer clock cycle. The timing diagram for the fast PWM mode is shown in Figure 32. The TCNT0 value is in the timing diagram shown as a histogram for illustrating the single-slope operation. The diagram includes non-inverted and inverted PWM outputs. The small horizontal line marks on the TCNT0 slopes represent compare matches between OCR0 and TCNT0. 77 2502K–AVR–10/06
Figure 32. Fast PWM Mode, Timing Diagram OCRn Interrupt Flag Set OCRn Update and TOVn Interrupt Flag Set TCNTn OCn (COMn1:0 = 2) OCn (COMn1:0 = 3) Period 1 2 3 4 5 6 7 The Timer/Counter Overflow Flag (TOV0) is set each time the counter reaches MAX. If the interrupt is enabled, the interrupt handler routine can be used for updating the com- pare value. In fast PWM mode, the compare unit allows generation of PWM waveforms on the OC0 pin. Setting the COM01:0 bits to two will produce a non-inverted PWM and an inverted PWM output can be generated by setting the COM01:0 to three (See Table 41 on page 84). The actual OC0 value will only be visible on the port pin if the data direction for the port pin is set as output. The PWM waveform is generated by setting (or clearing) the OC0 Register at the Compare Match between OCR0 and TCNT0, and clearing (or set- ting) the OC0 Register at the timer clock cycle the counter is cleared (changes from MAX to BOTTOM). The PWM frequency for the output can be calculated by the following equation: f clk_I/O f = ------------------ OCnPWM N⋅256 The “N” variable represents the prescale factor (1, 8, 64, 256, or 1024). The extreme values for the OCR0 Register represents special cases when generating a PWM waveform output in the fast PWM mode. If the OCR0 is set equal to BOTTOM, the output will be a narrow spike for each MAX+1 timer clock cycle. Setting the OCR0 equal to MAX will result in a constantly high or low output (depending on the polarity of the out- put set by the COM01:0 bits). A frequency (with 50% duty cycle) waveform output in fast PWM mode can be achieved by setting OC0 to toggle its logical level on each Compare Match (COM01:0 = 1). The waveform generated will have a maximum frequency of f = f /2 when OCR0 is OC0 clk_I/O set to zero. This feature is similar to the OC0 toggle in CTC mode, except the double buffer feature of the output compare unit is enabled in the fast PWM mode. ATmega8535(L) 78 2502K–AVR–10/06
ATmega8535(L) Phase Correct PWM Mode The phase correct PWM mode (WGM01:0 = 1) provides a high resolution phase correct PWM waveform generation option. The phase correct PWM mode is based on a dual- slope operation. The counter counts repeatedly from BOTTOM to MAX and then from MAX to BOTTOM. In non-inverting Compare Output mode, the Output Compare (OC0) is cleared on the Compare Match between TCNT0 and OCR0 while up-counting, and set on the Compare Match while down-counting. In inverting Output Compare mode, the operation is inverted. The dual-slope operation has lower maximum operation frequency than single slope operation. However, due to the symmetric feature of the dual-slope PWM modes, these modes are preferred for motor control applications. The PWM resolution for the phase correct PWM mode is fixed to eight bits. In phase correct PWM mode the counter is incremented until the counter value matches MAX. When the counter reaches MAX, it changes the count direction. The TCNT0 value will be equal to MAX for one timer clock cycle. The timing diagram for the phase correct PWM mode is shown on Figure 33. The TCNT0 value is in the timing diagram shown as a histogram for illustrating the dual-slope operation. The diagram includes non-inverted and inverted PWM outputs. The small horizontal line marks on the TCNT0 slopes repre- sent compare matches between OCR0 and TCNT0. Figure 33. Phase Correct PWM Mode, Timing Diagram OCn Interrupt Flag Set OCRn Update TOVn Interrupt Flag Set TCNTn OCn (COMn1:0 = 2) OCn (COMn1:0 = 3) Period 1 2 3 The Timer/Counter Overflow Flag (TOV0) is set each time the counter reaches BOT- TOM. The interrupt flag can be used to generate an interrupt each time the counter reaches the BOTTOM value. In phase correct PWM mode, the compare unit allows generation of PWM waveforms on the OC0 pin. Setting the COM01:0 bits to two will produce a non-inverted PWM. An inverted PWM output can be generated by setting the COM01:0 to three (See Table 42 on page 84). The actual OC0 value will only be visible on the port pin if the data direction for the port pin is set as output. The PWM waveform is generated by clearing (or setting) the OC0 Register at the Compare Match between OCR0 and TCNT0 when the counter increments, and setting (or clearing) the OC0 Register at Compare Match between 79 2502K–AVR–10/06
OCR0 and TCNT0 when the counter decrements. The PWM frequency for the output when using phase correct PWM can be calculated by the following equation: f clk_I/O f = ------------------ OCnPCPWM N⋅510 The “N” variable represents the prescale factor (1, 8, 64, 256, or 1024). The extreme values for the OCR0 Register represent special cases when generating a PWM waveform output in the phase correct PWM mode. If the OCR0 is set equal to BOTTOM, the output will be continuously low and if set equal to MAX the output will be continuously high for non-inverted PWM mode. For inverted PWM the output will have the opposite logic values. AT the very start of period 2 in Figure 33 OCn has a transition from high to low even though there is no Compare Match. The point of this transition is to guarantee symmetry around BOTTOM. There are two cases that give a transition without Compare Match. (cid:129) OCR0 changes its value from MAX, like in Figure 33. When the OCR0 value is MAX the OCn pin value is the same as the result of a down-counting Compare Match. To ensure symmetry around BOTTOM the OCn value at MAX must correspond to the result of an up-counting Compare Match. (cid:129) The timer starts counting from a value higher than the one in OCR0, and for that reason misses the Compare Match and hence the OCn change that would have happened on the way up. Timer/Counter Timing The Timer/Counter is a synchronous design and the timer clock (clk ) is therefore T0 Diagrams shown as a clock enable signal in the following figures. The figures include information on when interrupt flags are set. Figure 34 contains timing data for basic Timer/Counter operation. The figure shows the count sequence close to the MAX value in all modes other than phase correct PWM mode. Figure 34. Timer/Counter Timing Diagram, no Prescaling clk I/O clk Tn (clk /1) I/O TCNTn MAX - 1 MAX BOTTOM BOTTOM + 1 TOVn Figure 35 shows the same timing data, but with the prescaler enabled. ATmega8535(L) 80 2502K–AVR–10/06
ATmega8535(L) Figure 35. Timer/Counter Timing Diagram, with Prescaler (f /8) clk_I/O clk I/O clk Tn (clk /8) I/O TCNTn MAX - 1 MAX BOTTOM BOTTOM + 1 TOVn Figure 36 shows the setting of OCF0 in all modes except CTC mode. Figure 36. Timer/Counter Timing Diagram, Setting of OCF0, with Prescaler (f /8) clk_I/O clk I/O clk Tn (clk /8) I/O TCNTn OCRn - 1 OCRn OCRn + 1 OCRn + 2 OCRn OCRn Value OCFn Figure 37 shows the setting of OCF0 and the clearing of TCNT0 in CTC mode. 81 2502K–AVR–10/06
Figure 37. Timer/Counter Timing Diagram, Clear Timer on Compare Match Mode, with Prescaler (f /8) clk_I/O clk I/O clk Tn (clk /8) I/O TCNTn TOP - 1 TOP BOTTOM BOTTOM + 1 (CTC) OCRn TOP OCFn ATmega8535(L) 82 2502K–AVR–10/06
ATmega8535(L) 8-bit Timer/Counter Register Description Timer/Counter Control Register – TCCR0 Bit 7 6 5 4 3 2 1 0 FOC0 WGM00 COM01 COM00 WGM01 CS02 CS01 CS00 TCCR0 Read/Write W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 7 – FOC0: Force Output Compare The FOC0 bit is only active when the WGM00 bit specifies a non-PWM mode. However, for ensuring compatibility with future devices, this bit must be set to zero when TCCR0 is written when operating in PWM mode. When writing a logical one to the FOC0 bit, an immediate Compare Match is forced on the Waveform Generation unit. The OC0 output is changed according to its COM01:0 bits setting. Note that the FOC0 bit is implemented as a strobe. Therefore it is the value present in the COM01:0 bits that determines the effect of the forced compare. A FOC0 strobe will not generate any interrupt, nor will it clear the timer in CTC mode using OCR0 as TOP. The FOC0 bit is always read as zero. (cid:129) Bit 6, 3 – WGM01:0: Waveform Generation Mode These bits control the counting sequence of the counter, the source for the maximum (TOP) counter value, and what type of waveform generation to be used. Modes of oper- ation supported by the Timer/Counter unit are: Normal mode, Clear Timer on Compare Match (CTC) mode, and two types of Pulse Width Modulation (PWM) modes. See Table 39 and “Modes of Operation” on page 76. Table 39. Waveform Generation Mode Bit Description(1) WGM01 WGM00 Update of TOV0 Flag Mode (CTC0) (PWM0) Mode of Operation TOP OCR0 Set on 0 0 0 Normal 0xFF Immediate MAX 1 0 1 PWM, Phase Correct 0xFF TOP BOTTOM 2 1 0 CTC OCR0 Immediate MAX 3 1 1 Fast PWM 0xFF BOTTOM MAX Note: 1. The CTC0 and PWM0 bit definition names are now obsolete. Use the WGM01:0 def- initions. However, the functionality and location of these bits are compatible with previous versions of the Timer. (cid:129) Bit 5:4 – COM01:0: Compare Match Output Mode These bits control the Output Compare pin (OC0) behavior. If one or both of the COM01:0 bits are set, the OC0 output overrides the normal port functionality of the I/O pin it is connected to. However, note that the Data Direction Register (DDR) bit corre- sponding to the OC0 pin must be set in order to enable the output driver. 83 2502K–AVR–10/06
When OC0 is connected to the pin, the function of the COM01:0 bits depends on the WGM01:0 bit setting. Table 40 shows the COM01:0 bit functionality when the WGM01:0 bits are set to a normal or CTC mode (non-PWM). Table 40. Compare Output Mode, non-PWM Mode COM01 COM00 Description 0 0 Normal port operation, OC0 disconnected. 0 1 Toggle OC0 on Compare Match 1 0 Clear OC0 on Compare Match 1 1 Set OC0 on Compare Match Table 41 shows the COM01:0 bit functionality when the WGM01:0 bits are set to fast PWM mode. Table 41. Compare Output Mode, Fast PWM Mode(1) COM01 COM00 Description 0 0 Normal port operation, OC0 disconnected. 0 1 Reserved 1 0 Clear OC0 on Compare Match, set OC0 at TOP (Non-Inverting). 1 1 Set OC0 on Compare Match, clear OC0 at TOP (Inverting) Note: 1. A special case occurs when OCR0 equals TOP and COM01 is set. In this case, the Compare Match is ignored, but the set or clear is done at TOP. See “Fast PWM Mode” on page 77 for more details. Table 42 shows the COM01:0 bit functionality when the WGM01:0 bits are set to phase correct PWM mode. Table 42. Compare Output Mode, Phase Correct PWM Mode(1) COM01 COM00 Description 0 0 Normal port operation, OC0 disconnected. 0 1 Reserved 1 0 Clear OC0 on Compare Match when up-counting. Set OC0 on Compare Match when down-counting. 1 1 Set OC0 on Compare Match when up-counting. Clear OC0 on Compare Match when down-counting. Note: 1. A special case occurs when OCR0 equals TOP and COM01 is set. In this case, the Compare Match is ignored, but the set or clear is done at TOP. See “Phase Correct PWM Mode” on page 79 for more details. ATmega8535(L) 84 2502K–AVR–10/06
ATmega8535(L) (cid:129) Bit 2:0 – CS02:0: Clock Select The three Clock Select bits select the clock source to be used by the Timer/Counter. Table 43. Clock Select Bit Description CS02 CS01 CS00 Description 0 0 0 No clock source (Timer/counter stopped). 0 0 1 clk /(No prescaling) I/O 0 1 0 clk /8 (From prescaler) I/O 0 1 1 clk /64 (From prescaler) I/O 1 0 0 clk /256 (From prescaler) I/O 1 0 1 clk /1024 (From prescaler) I/O 1 1 0 External clock source on T0 pin. Clock on falling edge. 1 1 1 External clock source on T0 pin. Clock on rising edge. If external pin modes are used for the Timer/Counter0, transitions on the T0 pin will clock the counter even if the pin is configured as an output. This feature allows software control of the counting. Timer/Counter Register – TCNT0 Bit 7 6 5 4 3 2 1 0 TCNT0[7:0] TCNT0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 The Timer/Counter Register gives direct access, both for read and write operations, to the Timer/Counter unit 8-bit counter. Writing to the TCNT0 Register blocks (removes) the Compare Match on the following timer clock. Modifying the counter (TCNT0) while the counter is running, introduces a risk of missing a Compare Match between TCNT0 and the OCR0 Register. Output Compare Register – OCR0 Bit 7 6 5 4 3 2 1 0 OCR0[7:0] OCR0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 The Output Compare Register contains an 8-bit value that is continuously compared with the counter value (TCNT0). A match can be used to generate an output compare interrupt, or to generate a waveform output on the OC0 pin. Timer/Counter Interrupt Mask Register – TIMSK Bit 7 6 5 4 3 2 1 0 OCIE2 TOIE2 TICIE1 OCIE1A OCIE1B TOIE1 OCIE0 TOIE0 TIMSK Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 1 – OCIE0: Timer/Counter0 Output Compare Match Interrupt Enable When the OCIE0 bit is written to one, and the I-bit in the Status Register is set (one), the Timer/Counter0 Compare Match interrupt is enabled. The corresponding interrupt is executed if a Compare Match in Timer/Counter0 occurs (i.e., when the OCF0 bit is set in the Timer/Counter Interrupt Flag Register – TIFR). 85 2502K–AVR–10/06
(cid:129) Bit 0 – TOIE0: Timer/Counter0 Overflow Interrupt Enable When the TOIE0 bit is written to one, and the I-bit in the Status Register is set (one), the Timer/Counter0 Overflow interrupt is enabled. The corresponding interrupt is executed if an overflow in Timer/Counter0 occurs (i.e., when the TOV0 bit is set in the Timer/Counter Interrupt Flag Register – TIFR). Timer/Counter Interrupt Flag Register – TIFR Bit 7 6 5 4 3 2 1 0 OCF2 TOV2 ICF1 OCF1A OCF1B TOV1 OCF0 TOV0 TIFR Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 1 – OCF0: Output Compare Flag 0 The OCF0 bit is set (one) when a Compare Match occurs between the Timer/Counter0 and the data in OCR0 – Output Compare Register0. OCF0 is cleared by hardware when executing the corresponding interrupt handling vector. Alternatively, OCF0 is cleared by writing a logic one to the flag. When the I-bit in SREG, OCIE0 (Timer/Counter0 Com- pare Match Interrupt Enable), and OCF0 are set (one), the Timer/Counter0 Compare Match Interrupt is executed. (cid:129) Bit 0 – TOV0: Timer/Counter0 Overflow Flag The bit TOV0 is set (one) when an overflow occurs in Timer/Counter0. TOV0 is cleared by hardware when executing the corresponding interrupt handling vector. Alternatively, TOV0 is cleared by writing a logic one to the flag. When the SREG I-bit, TOIE0 (Timer/Counter0 Overflow Interrupt Enable), and TOV0 are set (one), the Timer/Counter0 Overflow Interrupt is executed. In phase correct PWM mode, this bit is set when Timer/Counter0 changes counting direction at 0x00. ATmega8535(L) 86 2502K–AVR–10/06
ATmega8535(L) Timer/Counter0 and Timer/Counter1 and Timer/Counter0 share the same prescaler module, but the Timer/Counter1 Timer/Counters can have different prescaler settings. The description below applies to both Timer/Counter1 and Timer/Counter0. Prescalers Internal Clock Source The Timer/Counter can be clocked directly by the system clock (by setting the CSn2:0=1). This provides the fastest operation, with a maximum Timer/Counter clock frequency equal to system clock frequency (f ). Alternatively, one of four taps from CLK_I/O the prescaler can be used as a clock source. The prescaled clock has a frequency of either f /8, f /64, f /256, or f /1024. CLK_I/O CLK_I/O CLK_I/O CLK_I/O Prescaler Reset The prescaler is free running (i.e., operates independently of the clock select logic of the Timer/Counter) and it is shared by Timer/Counter1 and Timer/Counter0. Since the pres- caler is not affected by the Timer/Counter’s clock select, the state of the prescaler will have implications for situations where a prescaled clock is used. One example of pres- caling artifacts occurs when the timer is enabled and clocked by the prescaler (6>CSn2:0 > 1). The number of system clock cycles from when the timer is enabled to the first count occurs can be from 1 to N+1 system clock cycles, where N equals the prescaler divisor (8, 64, 256, or 1024). It is possible to use the Prescaler Reset for synchronizing the Timer/Counter to program execution. However, care must be taken if the other Timer/Counter that shares the same prescaler also uses prescaling. A prescaler reset will affect the prescaler period for all Timer/Counters it is connected to. External Clock Source An external clock source applied to the T1/T0 pin can be used as Timer/Counter clock (clk /clk ). The T1/T0 pin is sampled once every system clock cycle by the pin syn- T1 T0 chronization logic. The synchronized (sampled) signal is then passed through the edge detector. Figure 38 shows a functional equivalent block diagram of the T1/T0 synchroni- zation and edge detector logic. The registers are clocked at the positive edge of the internal system clock (clk ). The latch is transparent in the high period of the internal I/O system clock. The edge detector generates one clk /clk pulse for each positive (CSn2:0 = 7) or neg- T1 T0 ative (CSn2:0 = 6) edge it detects. Figure 38. T1/T0 Pin Sampling Tn D Q D Q D Q Tn_sync (To Clock Select Logic) LE clk I/O Synchronization Edge Detector The synchronization and edge detector logic introduces a delay of 2.5 to 3.5 system clock cycles from an edge has been applied to the T1/T0 pin to the counter is updated. Enabling and disabling of the clock input must be done when T1/T0 has been stable for at least one system clock cycle, otherwise it is a risk that a false Timer/Counter clock pulse is generated. 87 2502K–AVR–10/06
Each half period of the external clock applied must be longer than one system clock cycle to ensure correct sampling. The external clock must be guaranteed to have less than half the system clock frequency (f < f /2) given a 50/50% duty cycle. Since ExtClk clk_I/O the edge detector uses sampling, the maximum frequency of an external clock it can detect is half the sampling frequency (Nyquist sampling theorem). However, due to vari- ation of the system clock frequency and duty cycle caused by Oscillator source (crystal, resonator, and capacitors) tolerances, it is recommended that maximum frequency of an external clock source is less than f /2.5. clk_I/O An external clock source can not be prescaled. Figure 39. Prescaler for Timer/Counter0 and Timer/Counter1(1) clk I/O Clear PSR10 T0 Synchronization T1 Synchronization clk clk T1 T0 Note: 1. The synchronization logic on the input pins (T1/T0) is shown in Figure 38. Special Function IO Register – SFIOR Bit 7 6 5 4 3 2 1 0 ADTS2 ADTS1 ADTS0 – ACME PUD PSR2 PSR10 SFIOR Read/Write R/W R/W R/W R R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 0 – PSR10: Prescaler Reset Timer/Counter1 and Timer/Counter0 When this bit is written to one, the Timer/Counter1 and Timer/Counter0 prescaler will be reset. The bit will be cleared by hardware after the operation is performed. Writing a zero to this bit will have no effect. Note that Timer/Counter1 and Timer/Counter0 share the same prescaler and a reset of this prescaler will affect both timers. This bit will always be read as zero. ATmega8535(L) 88 2502K–AVR–10/06
ATmega8535(L) 16-bit The 16-bit Timer/Counter unit allows accurate program execution timing (event man- Timer/Counter1 agement), wave generation, and signal timing measurement. The main features are: (cid:129) True 16-bit Design (i.e., Allows 16-bit PWM) (cid:129) Two Independent Output Compare Units (cid:129) Double Buffered Output Compare Registers (cid:129) One Input Capture Unit (cid:129) Input Capture Noise Canceler (cid:129) Clear Timer on Compare Match (Auto Reload) (cid:129) Glitch-free, Phase Correct Pulse Width Modulator (PWM) (cid:129) Variable PWM Period (cid:129) Frequency Generator (cid:129) External Event Counter (cid:129) Four Independent Interrupt Sources (TOV1, OCF1A, OCF1B, and ICF1) Overview Most register and bit references in this section are written in general form. A lower case “n” replaces the Timer/Counter number, and a lower case “x” replaces the Output Com- pare unit channel. However, when using the register or bit defines in a program, the precise form must be used, i.e., TCNT1 for accessing Timer/Counter1 counter value and so on. A simplified block diagram of the 16-bit Timer/Counter is shown in Figure 40. For the actual placement of I/O pins, refer to “Pinout ATmega8535” on page 2. CPU accessible I/O Registers, including I/O bits and I/O pins, are shown in bold. The device-specific I/O Register and bit locations are listed in the “16-bit Timer/Counter Register Description” on page 110. 89 2502K–AVR–10/06
Figure 40. 16-bit Timer/Counter Block Diagram(1) Count TOVn Clear (Int.Req.) Control Logic Direction clk Clock Select Tn Edge Tn Detector TOP BOTTOM ( From Prescaler ) Timer/Counter TCNTn = = 0 OCnA (Int.Req.) = Waveform OCnA Generation OCRnA Fixed OCnB TOP (Int.Req.) S U Values B = Waveform OCnB A Generation T A D OCRnB ( From Analog Comparator Ouput ) ICFn (Int.Req.) Edge Noise ICRn Detector Canceler ICPn TCCRnA TCCRnB Note: 1. Refer to Figure 1 on page 2, Table 26 on page 60, and Table 32 on page 64 for Timer/Counter1 pin placement and description. Registers The Timer/Counter (TCNT1), Output Compare Registers (OCR1A/B), and Input Capture Register (ICR1) are all 16-bit registers. Special procedures must be followed when accessing the 16-bit registers. These procedures are described in the section “Access- ing 16-bit Registers” on page 92. The Timer/Counter Control Registers (TCCR1A/B) are 8-bit registers and have no CPU access restrictions. Interrupt requests (abbreviated to Int.Req. in the figure) signals are all visible in the Timer Interrupt Flag Register (TIFR). All interrupts are individually masked with the Timer Interrupt Mask Register (TIMSK). TIFR and TIMSK are not shown in the figure since these registers are shared by other timer units. The Timer/Counter can be clocked internally, via the prescaler, or by an external clock source on the T1 pin. The Clock Select logic block controls which clock source and edge the Timer/Counter uses to increment (or decrement) its value. The Timer/Counter is inactive when no clock source is selected. The output from the Clock Select logic is referred to as the timer clock (clk ). T1 The double buffered Output Compare Registers (OCR1A/B) are compared with the Timer/Counter value at all times. The result of the compare can be used by the ATmega8535(L) 90 2502K–AVR–10/06
ATmega8535(L) Waveform Generator to generate a PWM or variable frequency output on the Output Compare Pin (OC1A/B). See “Output Compare Units” on page 98. The Compare Match event will also set the Compare Match Flag (OCF1A/B) which can be used to generate an output compare interrupt request. The Input Capture Register can capture the Timer/Counter value at a given external (edge triggered) event on either the Input Capture Pin (ICP1) or on the Analog Compar- ator pins (See “Analog Comparator” on page 203.) The Input Capture unit includes a digital filtering unit (Noise Canceler) for reducing the chance of capturing noise spikes. The TOP value, or maximum Timer/Counter value, can in some modes of operation be defined by either the OCR1A Register, the ICR1 Register, or by a set of fixed values. When using OCR1A as TOP value in a PWM mode, the OCR1A Register can not be used for generating a PWM output. However, the TOP value will, in this case, be double buffered allowing the TOP value to be changed in run time. If a fixed TOP value is required, the ICR1 Register can be used as an alternative, freeing the OCR1A to be used as PWM output. Definitions The following definitions are used extensively throughout the document Table 44. Definitions BOTTOM The counter reaches the BOTTOM when it becomes 0x0000. MAX The counter reaches its MAXimum when it becomes 0xFFFF (decimal 65535). TOP The counter reaches the TOP when it becomes equal to the highest value in the count sequence. The TOP value can be assigned to be one of the fixed values: 0x00FF, 0x01FF, or 0x03FF, or to the value stored in the OCR1A or ICR1 Register. The assignment is dependent of the mode of operation. Compatibility The 16-bit Timer/Counter has been updated and improved from previous versions of the 16-bit AVR Timer/Counter. This 16-bit Timer/Counter is fully compatible with the earlier version regarding: (cid:129) All 16-bit Timer/Counter related I/O Register address locations, including Timer Interrupt Registers. (cid:129) Bit locations inside all 16-bit Timer/Counter Registers, including Timer Interrupt Registers. (cid:129) Interrupt Vectors. The following control bits have changed names, but have the same functionality and register location: (cid:129) PWM10 is changed to WGM10. (cid:129) PWM11 is changed to WGM11. (cid:129) CTC1 is changed to WGM12. The following bits are added to the 16-bit Timer/Counter Control Registers: (cid:129) FOC1A and FOC1B are added to TCCR1A. (cid:129) WGM13 is added to TCCR1B. The 16-bit Timer/Counter has improvements that will affect the compatibility in some special cases. 91 2502K–AVR–10/06
Accessing 16-bit The TCNT1, OCR1A/B, and ICR1 are 16-bit registers that can be accessed by the AVR Registers CPU via the 8-bit data bus. The 16-bit register must be byte accessed using two read or write operations. Each 16-bit timer has a single 8-bit register for temporary storing of the high byte of the 16-bit access. The same temporary register is shared between all 16-bit registers within each 16-bit timer. Accessing the low byte triggers the 16-bit read or write operation. When the low byte of a 16-bit register is written by the CPU, the high byte stored in the temporary register, and the low byte written are both copied into the 16-bit register in the same clock cycle. When the low byte of a 16-bit register is read by the CPU, the high byte of the 16-bit register is copied into the temporary register in the same clock cycle as the low byte is read. Not all 16-bit accesses uses the temporary register for the high byte. Reading the OCR1A/B 16-bit registers does not involve using the temporary register. To do a 16-bit write, the high byte must be written before the low byte. For a 16-bit read, the low byte must be read before the high byte. The following code examples show how to access the 16-bit Timer Registers assuming that no interrupts update the temporary register. The same principle can be used directly for accessing the OCR1A/B and ICR1 Registers. Note that when using “C”, the compiler handles the 16-bit access. Assembly Code Examples(1) ... ; Set TCNT1 to 0x01FF ldi r17,0x01 ldi r16,0xFF out TCNT1H,r17 out TCNT1L,r16 ; Read TCNT1 into r17:r16 in r16,TCNT1L in r17,TCNT1H ... C Code Examples(1) unsigned int i; ... /* Set TCNT1 to 0x01FF */ TCNT1 = 0x1FF; /* Read TCNT1 into i */ i = TCNT1; ... Note: 1. See “About Code Examples” on page 7. The assembly code example returns the TCNT1 value in the r17:r16 register pair. It is important to notice that accessing 16-bit registers are atomic operations. If an inter- rupt occurs between the two instructions accessing the 16-bit register, and the interrupt code updates the temporary register by accessing the same or any other of the 16-bit Timer Registers, then the result of the access outside the interrupt will be corrupted. Therefore, when both the main code and the interrupt code update the temporary regis- ter, the main code must disable the interrupts during the 16-bit access. ATmega8535(L) 92 2502K–AVR–10/06
ATmega8535(L) The following code examples show how to do an atomic read of the TCNT1 Register contents. Reading any of the OCR1A/B or ICR1 Registers can be done by using the same principle. Assembly Code Example(1) TIM16_ReadTCNT1: ; Save Global Interrupt Flag in r18,SREG ; Disable interrupts cli ; Read TCNT1 into r17:r16 in r16,TCNT1L in r17,TCNT1H ; Restore Global Interrupt Flag out SREG,r18 ret C Code Example(1) unsigned int TIM16_ReadTCNT1( void ) { unsigned char sreg; unsigned int i; /* Save Global Interrupt Flag */ sreg = SREG; /* Disable interrupts */ _CLI(); /* Read TCNT1 into i */ i = TCNT1; /* Restore Global Interrupt Flag */ SREG = sreg; return i; } Note: 1. See “About Code Examples” on page 7. The assembly code example returns the TCNT1 value in the r17:r16 register pair. 93 2502K–AVR–10/06
The following code examples show how to do an atomic write of the TCNT1 Register contents. Writing any of the OCR1A/B or ICR1 Registers can be done by using the same principle. Assembly Code Example(1) TIM16_WriteTCNT1: ; Save Global Interrupt Flag in r18,SREG ; Disable interrupts cli ; Set TCNT1 to r17:r16 out TCNT1H,r17 out TCNT1L,r16 ; Restore Global Interrupt Flag out SREG,r18 ret C Code Example(1) void TIM16_WriteTCNT1( unsigned int i ) { unsigned char sreg; /* Save Global Interrupt Flag */ sreg = SREG; /* Disable interrupts */ _CLI(); /* Set TCNT1 to i */ TCNT1 = i; /* Restore Global Interrupt Flag */ SREG = sreg; } Note: 1. See “About Code Examples” on page 7. The assembly code example requires that the r17:r16 register pair contains the value to be written to TCNT1. Re-using the Temporary High If writing to more than one 16-bit register where the high byte is the same for all registers Byte Register written, then the high byte only needs to be written once. However, note that the same rule of atomic operation described previously also applies in this case. ATmega8535(L) 94 2502K–AVR–10/06
ATmega8535(L) Timer/Counter Clock The Timer/Counter can be clocked by an internal or an external clock source. The clock Sources source is selected by the Clock Select logic which is controlled by the Clock Select (CS12:0) bits located in the Timer/Counter Control Register B (TCCR1B). For details on clock sources and prescaler, see “Timer/Counter0 and Timer/Counter1 Prescalers” on page 87. Counter Unit The main part of the 16-bit Timer/Counter is the programmable 16-bit bi-directional counter unit. Figure 41 shows a block diagram of the counter and its surroundings. Figure 41. Counter Unit Block Diagram DATA BUS (8-bit) TOVn (Int.Req.) TEMP (8-bit) Clock Select Count Edge Tn TCNTnH (8-bit) TCNTnL (8-bit) Clear clk Detector Control Logic Tn Direction TCNTn (16-bit Counter) ( From Prescaler ) TOP BOTTOM Signal description (internal signals): Count Increment or decrement TCNT1 by 1. Direction Select between increment and decrement. Clear Clear TCNT1 (set all bits to zero). clk Timer/Counter clock. T1 TOP Signalize that TCNT1 has reached maximum value. BOTTOM Signalize that TCNT1 has reached minimum value (zero). The 16-bit counter is mapped into two 8-bit I/O memory locations: Counter High (TCNT1H) containing the upper eight bits of the counter, and Counter Low (TCNT1L) containing the lower eight bits. The TCNT1H Register can only be indirectly accessed by the CPU. When the CPU does an access to the TCNT1H I/O location, the CPU accesses the high byte temporary register (TEMP). The temporary register is updated with the TCNT1H value when the TCNT1L is read, and TCNT1H is updated with the temporary register value when TCNT1L is written. This allows the CPU to read or write the entire 16-bit counter value within one clock cycle via the 8-bit data bus. It is impor- tant to notice that there are special cases of writing to the TCNT1 Register when the counter is counting that will give unpredictable results. The special cases are described in the sections where they are of importance. Depending on the mode of operation used, the counter is cleared, incremented, or dec- remented at each Timer Clock (clk ). The clk can be generated from an external or T1 T1 internal clock source, selected by the Clock Select bits (CS12:0). When no clock source is selected (CS12:0 = 0) the timer is stopped. However, the TCNT1 value can be accessed by the CPU, independent of whether clk is present or not. A CPU write over- T1 rides (has priority over) all counter clear or count operations. The counting sequence is determined by the setting of the Waveform Generation mode bits (WGM13:0) located in the Timer/Counter Control Registers A and B (TCCR1A and 95 2502K–AVR–10/06
TCCR1B). There are close connections between how the counter behaves (counts) and how waveforms are generated on the Output Compare outputs OC1x. For more details about advanced counting sequences and waveform generation, see “Modes of Opera- tion” on page 101. The Timer/Counter Overflow Flag (TOV1) is set according to the mode of operation selected by the WGM13:0 bits. TOV1 can be used for generating a CPU interrupt. Input Capture Unit The Timer/Counter incorporates an Input Capture unit that can capture external events and give them a time-stamp indicating time of occurrence. The external signal indicating an event, or multiple events, can be applied via the ICP1 pin or alternatively, via the analog comparator unit. The time-stamps can then be used to calculate frequency, duty- cycle, and other features of the signal applied. Alternatively the time-stamps can be used for creating a log of the events. The Input Capture unit is illustrated by the block diagram shown in Figure 42. The ele- ments of the block diagram that are not directly a part of the Input Capture unit are gray shaded. The small “n” in register and bit names indicates the Timer/Counter number. Figure 42. Input Capture Unit Block Diagram DATA BUS (8-bit) TEMP (8-bit) ICRnH (8-bit) ICRnL (8-bit) TCNTnH (8-bit) TCNTnL (8-bit) WRITE ICRn (16-bit Register) TCNTn (16-bit Counter) ACO* ACIC* ICNC ICES Analog Comparator Noise Edge ICFn (Int.Req.) Canceler Detector ICPn When a change of the logic level (an event) occurs on the Input Capture pin (ICP1), alternatively on the Analog Comparator output (ACO), and this change confirms to the setting of the edge detector, a capture will be triggered. When a capture is triggered, the 16-bit value of the counter (TCNT1) is written to the Input Capture Register (ICR1). The Input Capture Flag (ICF1) is set at the same system clock as the TCNT1 value is copied into ICR1 Register. If enabled (TICIE1 = 1), the Input Capture Flag generates an Input Capture interrupt. The ICF1 Flag is automatically cleared when the interrupt is executed. Alternatively the ICF1 Flag can be cleared by software by writing a logical one to its I/O bit location. Reading the 16-bit value in the Input Capture Register (ICR1) is done by first reading the low byte (ICR1L) and then the high byte (ICR1H). When the low byte is read the high ATmega8535(L) 96 2502K–AVR–10/06
ATmega8535(L) byte is copied into the high byte temporary register (TEMP). When the CPU reads the ICR1H I/O location it will access the TEMP Register. The ICR1 Register can only be written when using a Waveform Generation mode that utilizes the ICR1 Register for defining the counter’s TOP value. In these cases the Waveform Generation mode (WGM13:0) bits must be set before the TOP value can be written to the ICR1 Register. When writing the ICR1 Register the high byte must be writ- ten to the ICR1H I/O location before the low byte is written to ICR1L. For more information on how to access the 16-bit registers, refer to “Accessing 16-bit Registers” on page 92. Input Capture Trigger Source The main trigger source for the Input Capture unit is the Input Capture pin (ICP1). Timer/Counter1 can alternatively use the Analog Comparator output as trigger source for the Input Capture unit. The Analog Comparator is selected as trigger source by set- ting the Analog Comparator Input Capture (ACIC) bit in the Analog Comparator Control and Status Register (ACSR). Be aware that changing trigger source can trigger a cap- ture. The Input Capture Flag must therefore be cleared after the change. Both the Input Capture pin (ICP1) and the Analog Comparator output (ACO) inputs are sampled using the same technique as the T1 pin (Figure 38 on page 87). The edge detector is also identical. However, when the noise canceler is enabled, additional logic is inserted before the edge detector, which increases the delay by four system clock cycles. Note that the input of the noise canceler and edge detector is always enabled unless the Timer/Counter is set in a Waveform Generation mode that uses ICR1 to define TOP. An Input Capture can be triggered by software by controlling the port of the ICP1 pin. Noise Canceler The noise canceler improves noise immunity by using a simple digital filtering scheme. The noise canceler input is monitored over four samples, and all four must be equal for changing the output that, in turn, is used by the edge detector. The noise canceler is enabled by setting the Input Capture Noise Canceler (ICNC1) bit in Timer/Counter Control Register B (TCCR1B). When enabled, the noise canceler introduces additional four system clock cycles of delay from a change applied to the input, to the update of the ICR1 Register. The noise canceler uses the system clock and is therefore not affected by the prescaler. Using the Input Capture Unit The main challenge when using the Input Capture unit is to assign enough processor capacity for handling the incoming events. The time between two events is critical. If the processor has not read the captured value in the ICR1 Register before the next event occurs, the ICR1 will be overwritten with a new value. In this case the result of the cap- ture will be incorrect. When using the Input Capture interrupt, the ICR1 Register should be read as early in the interrupt handler routine as possible. Even though the Input Capture interrupt has rela- tively high priority, the maximum interrupt response time is dependent on the maximum number of clock cycles it takes to handle any of the other interrupt requests. Using the Input Capture unit in any mode of operation when the TOP value (resolution) is actively changed during operation, is not recommended. Measurement of an external signal’s duty cycle requires that the trigger edge is changed after each capture. Changing the edge sensing must be done as early as possible after the ICR1 Register has been read. After a change of the edge, the Input Capture Flag (ICF1) must be cleared by software (writing a logical one to the I/O bit location). For 97 2502K–AVR–10/06
measuring frequency only, the clearing of the ICF1 Flag is not required (if an interrupt handler is used). Output Compare Units The 16-bit comparator continuously compares TCNT1 with the Output Compare Regis- ter (OCR1x). If TCNT equals OCR1x the comparator signals a match. A match will set the Output Compare Flag (OCF1x) at the next timer clock cycle. If enabled (OCIE1x = 1), the Output Compare Flag generates an output compare interrupt. The OCF1x Flag is automatically cleared when the interrupt is executed. Alternatively the OCF1x Flag can be cleared by software by writing a logical one to its I/O bit location. The Waveform Gen- erator uses the match signal to generate an output according to operating mode set by the Waveform Generation mode (WGM13:0) bits and Compare Output mode (COM1x1:0) bits. The TOP and BOTTOM signals are used by the Waveform Generator for handling the special cases of the extreme values in some modes of operation. (See “Modes of Operation” on page 101.) A special feature of output compare unit A allows it to define the Timer/Counter TOP value (i.e., counter resolution). In addition to the counter resolution, the TOP value defines the period time for waveforms generated by the Waveform Generator. Figure 43 shows a block diagram of the output compare unit. The small “n” in the regis- ter and bit names indicates the device number (n = 1 for Timer/Counter1), and the “x” indicates output compare unit (A/B). The elements of the block diagram that are not directly a part of the output compare unit are gray shaded. Figure 43. Output Compare Unit, Block Diagram DATA BUS (8-bit) TEMP (8-bit) OCRnxH Buf. (8-bit) OCRnxL Buf. (8-bit) TCNTnH (8-bit) TCNTnL (8-bit) OCRnx Buffer (16-bit Register) TCNTn (16-bit Counter) OCRnxH (8-bit) OCRnxL (8-bit) OCRnx (16-bit Register) = (16-bit Comparator ) OCFnx (Int.Req.) TOP Waveform Generator OCnx BOTTOM WGMn3:0 COMnx1:0 The OCR1x Register is double buffered when using any of the twelve Pulse Width Mod- ulation (PWM) modes. For the Normal and Clear Timer on Compare (CTC) modes of operation, the double buffering is disabled. The double buffering synchronizes the update of the OCR1x Compare Register to either TOP or BOTTOM of the counting ATmega8535(L) 98 2502K–AVR–10/06
ATmega8535(L) sequence. The synchronization prevents the occurrence of odd-length, non-symmetrical PWM pulses, thereby making the output glitch-free. The OCR1x Register access may seem complex, but this is not the case. When the double buffering is enabled, the CPU has access to the OCR1x Buffer Register, and if double buffering is disabled the CPU will access the OCR1x directly. The content of the OCR1x (Buffer or Compare) Register is only changed by a write operation (the Timer/Counter does not update this register automatically as does the TCNT1– and ICR1 Register). Therefore OCR1x is not read via the high byte temporary register (TEMP). However, it is a good practice to read the low byte first as with accessing other 16-bit registers. Writing the OCR1x Registers must be done via the TEMP Register since the compare of all 16 bits is done continuously. The high byte (OCR1xH) has to be written first. When the high byte I/O location is written by the CPU, the TEMP Register will be updated by the value written. Then when the low byte (OCR1xL) is written to the lower eight bits, the high byte will be copied into the upper 8-bits of either the OCR1x Buffer or OCR1x Compare Register in the same system clock cycle. For more information of how to access the 16-bit registers refer to “Accessing 16-bit Registers” on page 92. Force Output Compare In non-PWM waveform generation modes, the match output of the comparator can be forced by writing a one to the Force Output Compare (FOC1x) bit. Forcing Compare Match will not set the OCF1x Flag or reload/clear the timer, but the OC1x pin will be updated as if a real Compare Match had occurred (the COM11:0 bits settings define whether the OC1x pin is set, cleared or toggled). Compare Match Blocking by All CPU writes to the TCNT1 Register will block any Compare Match that occurs in the TCNT1 Write next timer clock cycle, even when the timer is stopped. This feature allows OCR1x to be initialized to the same value as TCNT1 without triggering an interrupt when the Timer/Counter clock is enabled. Using the Output Compare Since writing TCNT1 in any mode of operation will block all compare matches for one Unit timer clock cycle, there are risks involved when changing TCNT1 when using any of the output compare channels, independent of whether the Timer/Counter is running or not. If the value written to TCNT1 equals the OCR1x value, the Compare Match will be missed, resulting in incorrect waveform generation. Do not write the TCNT1 equal to TOP in PWM modes with variable TOP values. The Compare Match for the TOP will be ignored and the counter will continue to 0xFFFF. Similarly, do not write the TCNT1 value equal to BOTTOM when the counter is down-counting. The setup of the OC1x should be performed before setting the Data Direction Register for the port pin to output. The easiest way of setting the OC1x value is to use the Force Output Compare (FOC1x) strobe bits in Normal mode. The OC1x Register keeps its value even when changing between Waveform Generation modes. Be aware that the COM1x1:0 bits are not double buffered together with the compare value. Changing the COM1x1:0 bits will take effect immediately. 99 2502K–AVR–10/06
Compare Match Output The Compare Output Mode (COM1x1:0) bits have two functions. The waveform genera- Unit tor uses the COM1x1:0 bits for defining the Output Compare (OC1x) state at the next Compare Match. Secondly the COM1x1:0 bits control the OC1x pin output source. Fig- ure 44 shows a simplified schematic of the logic affected by the COM1x1:0 bit setting. The I/O Registers, I/O bits, and I/O pins in the figure are shown in bold. Only the parts of the general I/O port Control Registers (DDR and PORT) that are affected by the COM1x1:0 bits are shown. When referring to the OC1x state, the reference is for the internal OC1x Register, not the OC1x pin. If a System Reset occurs, the OC1x Register is reset to “0”. Figure 44. Compare Match Output Unit, Schematic COMnx1 Waveform COMnx0 D Q Generator FOCnx 1 OCnx OCnx Pin 0 D Q S U B PORT A T A D D Q DDR clk I/O The general I/O port function is overridden by the Output Compare (OC1x) from the waveform generator if either of the COM1x1:0 bits are set. However, the OC1x pin direction (input or output) is still controlled by the Data Direction Register (DDR) for the port pin. The Data Direction Register bit for the OC1x pin (DDR_OC1x) must be set as output before the OC1x value is visible on the pin. The port override function is generally independent of the Waveform Generation mode, but there are some exceptions. Refer to Table 45, Table 46 and Table 47 for details. The design of the output compare pin logic allows initialization of the OC1x state before the output is enabled. Note that some COM1x1:0 bit settings are reserved for certain modes of operation. See “16-bit Timer/Counter Register Description” on page 110. The COM1x1:0 bits have no effect on the Input Capture unit. Compare Output Mode and The Waveform Generator uses the COM1x1:0 bits differently in Normal, CTC, and PWM Waveform Generation modes. For all modes, setting the COM1x1:0 = 0 tells the Waveform Generator that no action on the OC1x Register is to be performed on the next Compare Match. For com- pare output actions in the non-PWM modes refer to Table 45 on page 110. For fast PWM mode refer to Table 46 on page 111, and for phase correct and phase and fre- quency correct PWM refer to Table 47 on page 111. ATmega8535(L) 100 2502K–AVR–10/06
ATmega8535(L) A change of the COM1x1:0 bits state will have effect at the first Compare Match after the bits are written. For non-PWM modes, the action can be forced to have immediate effect by using the FOC1x strobe bits. Modes of Operation The mode of operation, i.e., the behavior of the Timer/Counter and the output compare pins, is defined by the combination of the Waveform Generation mode (WGM13:0) and Compare Output mode (COM1x1:0) bits. The Compare Output mode bits do not affect the counting sequence, while the Waveform Generation mode bits do. The COM1x1:0 bits control whether the PWM output generated should be inverted or not (inverted or non-inverted PWM). For non-PWM modes the COM1x1:0 bits control whether the out- put should be set, cleared or toggle at a Compare Match (See “Compare Match Output Unit” on page 100.) For detailed timing information refer to “Timer/Counter Timing Diagrams” on page 108. Normal Mode The simplest mode of operation is the Normal mode (WGM13:0 = 0). In this mode the counting direction is always up (incrementing), and no counter clear is performed. The counter simply overruns when it passes its maximum 16-bit value (MAX = 0xFFFF) and then restarts from the BOTTOM (0x0000). In normal operation the Timer/Counter Over- flow Flag (TOV1) will be set in the same timer clock cycle as the TCNT1 becomes zero. The TOV1 Flag in this case behaves like a 17th bit, except that it is only set, not cleared. However, combined with the timer overflow interrupt that automatically clears the TOV1 Flag, the timer resolution can be increased by software. There are no special cases to consider in the Normal mode, a new counter value can be written anytime. The Input Capture unit is easy to use in Normal mode. However, observe that the maxi- mum interval between the external events must not exceed the resolution of the counter. If the interval between events are too long, the timer overflow interrupt or the prescaler must be used to extend the resolution for the capture unit. The output compare units can be used to generate interrupts at some given time. Using the output compare to generate waveforms in normal mode is not recommended, since this will occupy too much of the CPU time. Clear Timer on Compare In Clear Timer on Compare or CTC mode (WGM13:0 = 4 or 12), the OCR1A or ICR1 Match (CTC) Mode Register is used to manipulate the counter resolution. In CTC mode the counter is cleared to zero when the counter value (TCNT1) matches either the OCR1A (WGM13:0 = 4) or the ICR1 (WGM13:0 = 12). The OCR1A or ICR1 define the top value for the counter, hence also its resolution. This mode allows greater control of the Compare Match output frequency. It also simplifies the operation of counting external events. The timing diagram for the CTC mode is shown in Figure 45. The counter value (TCNT1) increases until a Compare Match occurs with either OCR1A or ICR1, and then counter (TCNT1) is cleared. 101 2502K–AVR–10/06
Figure 45. CTC Mode, Timing Diagram OCnA Interrupt Flag Set or ICFn Interrupt Flag Set (Interrupt on TOP) TCNTn OCnA (COMnA1:0 = 1) (Toggle) Period 1 2 3 4 An interrupt can be generated each time the counter value reaches the TOP value by either using the OCF1A or ICF1 Flag according to the register used to define the TOP value. If the interrupt is enabled, the interrupt handler routine can be used for updating the TOP value. However, changing the TOP to a value close to BOTTOM when the counter is running with a low or no prescaler value must be done with care since the CTC mode does not have the double buffering feature. If the new value written to OCR1A or ICR1 is lower than the current value of TCNT1, the counter will miss the Compare Match. The counter will then have to count to its maximum value (0xFFFF) and wrap around starting at 0x0000 before the Compare Match can occur. In many cases this feature is not desirable. An alternative will then be to use the fast PWM mode using OCR1A for defining TOP (WGM13:0 = 15) since the OCR1A then will be double buffered. For generating a waveform output in CTC mode, the OC1A output can be set to toggle its logical level on each Compare Match by setting the compare output mode bits to tog- gle mode (COM1A1:0 = 1). The OC1A value will not be visible on the port pin unless the data direction for the pin is set to output (DDR_OC1A = 1). The waveform generated will have a maximum frequency of f = f /2 when OCR1A is set to zero (0x0000). The OC1A clk_I/O waveform frequency is defined by the following equation: f clk_I/O f = --------------------------------------------------- OCnA 2⋅N⋅(1+OCRnA) The N variable represents the prescaler factor (1, 8, 64, 256, or 1024). As for the Normal mode of operation, the TOV1 Flag is set in the same timer clock cycle that the counter counts from MAX to 0x0000. Fast PWM Mode The fast Pulse Width Modulation or fast PWM mode (WGM13:0 = 5, 6, 7, 14, or 15) pro- vides a high frequency PWM waveform generation option. The fast PWM differs from the other PWM options by its single-slope operation. The counter counts from BOTTOM to TOP then restarts from BOTTOM. In non-inverting Compare Output mode, the Output Compare (OC1x) is set on the Compare Match between TCNT1 and OCR1x, and cleared at BOTTOM. In inverting Compare Output mode output is cleared on Compare Match and set at BOTTOM. Due to the single-slope operation, the operating frequency of the fast PWM mode can be twice as high as the phase correct and phase and fre- quency correct PWM modes that use dual-slope operation. This high frequency makes the fast PWM mode well suited for power regulation, rectification, and DAC applications. ATmega8535(L) 102 2502K–AVR–10/06
ATmega8535(L) High frequency allows physically small sized external components (coils, capacitors), hence reducing total system cost. The PWM resolution for fast PWM can be fixed to 8-, 9-, or 10-bit, or defined by either ICR1 or OCR1A. The minimum resolution allowed is 2-bit (ICR1 or OCR1A set to 0x0003), and the maximum resolution is 16-bit (ICR1 or OCR1A set to MAX). The PWM resolution can be calculated in bits by using the following equation: log(TOP+1) R = ----------------------------------- FPWM log(2) In fast PWM mode the counter is incremented until the counter value matches either one of the fixed values 0x00FF, 0x01FF, or 0x03FF (WGM13:0 = 5, 6, or 7), the value in ICR1 (WGM13:0 = 14), or the value in OCR1A (WGM13:0 = 15). The counter is then cleared at the following timer clock cycle. The timing diagram for the fast PWM mode is shown in Figure 46. The figure shows fast PWM mode when OCR1A or ICR1 is used to define TOP. The TCNT1 value is in the timing diagram shown as a histogram for illus- trating the single-slope operation. The diagram includes non-inverted and inverted PWM outputs. The small horizontal line marks on the TCNT1 slopes represent compare matches between OCR1x and TCNT1. The OC1x Interrupt Flag will be set when a Com- pare Match occurs. Figure 46. Fast PWM Mode, Timing Diagram OCRnx / TOP Update and TOVn Interrupt Flag Set and OCnA Interrupt Flag Set or ICFn Interrupt Flag Set (Interrupt on TOP) TCNTn OCnx (COMnx1:0 = 2) OCnx (COMnx1:0 = 3) Period 1 2 3 4 5 6 7 8 The Timer/Counter Overflow Flag (TOV1) is set each time the counter reaches TOP. In addition the OC1A or ICF1 Flag is set at the same timer clock cycle as TOV1 is set when either OCR1A or ICR1 is used for defining the TOP value. If one of the interrupts are enabled, the interrupt handler routine can be used for updating the TOP and com- pare values. When changing the TOP value the program must ensure that the new TOP value is higher or equal to the value of all of the compare registers. If the TOP value is lower than any of the compare registers, a Compare Match will never occur between the TCNT1 and the OCR1x. Note that when using fixed TOP values the unused bits are masked to zero when any of the OCR1x Registers are written. The procedure for updating ICR1 differs from updating OCR1A when used for defining the TOP value. The ICR1 Register is not double buffered. This means that if ICR1 is changed to a low value when the counter is running with a low or none prescaler value, there is a risk that the new ICR1 value written is lower than the current value of TCNT1. The result will then be that the counter will miss the Compare Match at the TOP value. 103 2502K–AVR–10/06
The counter will then have to count to the MAX value (0xFFFF) and wrap around start- ing at 0x0000 before the Compare Match can occur. The OCR1A Register however, is double buffered. This feature allows the OCR1A I/O location to be written anytime. When the OCR1A I/O location is written the value written will be put into the OCR1A Buffer Register. The OCR1A Compare Register will then be updated with the value in the Buffer Register at the next timer clock cycle the TCNT1 matches TOP. The update is done at the same timer clock cycle as the TCNT1 is cleared and the TOV1 Flag is set. Using the ICR1 Register for defining TOP works well when using fixed TOP values. By using ICR1, the OCR1A Register is free to be used for generating a PWM output on OC1A. However, if the base PWM frequency is actively changed (by changing the TOP value), using the OCR1A as TOP is clearly a better choice due to its double buffer feature. In fast PWM mode, the compare units allow generation of PWM waveforms on the OC1x pins. Setting the COM1x1:0 bits to two will produce a non-inverted PWM and an inverted PWM output can be generated by setting the COM1x1:0 to three (See Table 46 on page 111). The actual OC1x value will only be visible on the port pin if the data direc- tion for the port pin is set as output (DDR_OC1x). The PWM waveform is generated by setting (or clearing) the OC1x Register at the Compare Match between OCR1x and TCNT1, and clearing (or setting) the OC1x Register at the timer clock cycle the counter is cleared (changes from TOP to BOTTOM). The PWM frequency for the output can be calculated by the following equation: f clk_I/O f = ----------------------------------- OCnxPWM N⋅(1+TOP) The “N” variable represents the prescaler divider (1, 8, 64, 256, or 1024). The extreme values for the OCR1x Register represents special cases when generating a PWM waveform output in the fast PWM mode. If the OCR1x is set equal to BOTTOM (0x0000) the output will be a narrow spike for each TOP+1 timer clock cycle. Setting the OCR1x equal to TOP will result in a constant high or low output (depending on the polar- ity of the output set by the COM1x1:0 bits). A frequency (with 50% duty cycle) waveform output in fast PWM mode can be achieved by setting OC1A to toggle its logical level on each Compare Match (COM1A1:0 = 1). This applies only if OCR1A is used to define the TOP value (WGM13:0 = 15). The wave- form generated will have a maximum frequency of f = f /2 when OCR1A is set to OC1A clk_I/O zero (0x0000). This feature is similar to the OC1A toggle in CTC mode, except the dou- ble buffer feature of the output compare unit is enabled in the fast PWM mode. Phase Correct PWM Mode The phase correct Pulse Width Modulation or phase correct PWM mode (WGM13:0=1,2,3,10,or11) provides a high resolution phase correct PWM waveform generation option. The phase correct PWM mode is, like the phase and frequency cor- rect PWM mode, based on a dual-slope operation. The counter counts repeatedly from BOTTOM (0x0000) to TOP and then from TOP to BOTTOM. In non-inverting Compare Output mode, the Output Compare (OC1x) is cleared on the Compare Match between TCNT1 and OCR1x while up-counting and set on the Compare Match while down- counting. In inverting Output Compare mode, the operation is inverted. The dual-slope operation has lower maximum operation frequency than single slope operation. How- ever, due to the symmetric feature of the dual-slope PWM modes, these modes are preferred for motor control applications. The PWM resolution for the phase correct PWM mode can be fixed to 8-, 9-, or 10-bit, or defined by either ICR1 or OCR1A. The minimum resolution allowed is 2-bit (ICR1 or ATmega8535(L) 104 2502K–AVR–10/06
ATmega8535(L) OCR1A set to 0x0003), and the maximum resolution is 16-bit (ICR1 or OCR1A set to MAX). The PWM resolution can be calculated in bits by using the following equation: log(TOP+1) R = ----------------------------------- PCPWM log(2) In phase correct PWM mode, the counter is incremented until the counter value matches either one of the fixed values 0x00FF, 0x01FF, or 0x03FF (WGM13:0 = 1, 2, or 3), the value in ICR1 (WGM13:0 = 10), or the value in OCR1A (WGM13:0 = 11). The counter has then reached the TOP and changes the count direction. The TCNT1 value will be equal to TOP for one timer clock cycle. The timing diagram for the phase correct PWM mode is shown on Figure 47. The figure shows phase correct PWM mode when OCR1A or ICR1 is used to define TOP. The TCNT1 value is in the timing diagram shown as a histogram for illustrating the dual-slope operation. The diagram includes non-inverted and inverted PWM outputs. The small horizontal line marks on the TCNT1 slopes represent compare matches between OCR1x and TCNT1. The OC1x Interrupt Flag will be set when a Compare Match occurs. Figure 47. Phase Correct PWM Mode, Timing Diagram OCRnx/TOP Update and OCnA Interrupt Flag Set or ICFn Interrupt Flag Set (Interrupt on TOP) TOVn Interrupt Flag Set (Interrupt on Bottom) TCNTn OCnx (COMnx1:0 = 2) OCnx (COMnx1:0 = 3) Period 1 2 3 4 The Timer/Counter Overflow Flag (TOV1) is set each time the counter reaches BOT- TOM. When either OCR1A or ICR1 is used for defining the TOP value, the OC1A or ICF1 Flag is set accordingly at the same timer clock cycle as the OCR1x Registers are updated with the double buffer value (at TOP). The interrupt flags can be used to gener- ate an interrupt each time the counter reaches the TOP or BOTTOM value. When changing the TOP value, the program must ensure that the new TOP value is higher or equal to the value of all of the compare registers. If the TOP value is lower than any of the compare registers, a Compare Match will never occur between the TCNT1 and the OCR1x. Note that when using fixed TOP values, the unused bits are masked to zero when any of the OCR1x Registers are written. As the third period shown in Figure 47 illustrates, changing the TOP actively while the Timer/Counter is running in the phase correct mode can result in an unsymmetrical output. The reason for this can be found in the time of update of the OCR1x Register. Since the OCR1x update occurs at TOP, the PWM period starts and ends at TOP. This implies that the length of the fall- 105 2502K–AVR–10/06
ing slope is determined by the previous TOP value, while the length of the rising slope is determined by the new TOP value. When these two values differ the two slopes of the period will differ in length. The difference in length gives the unsymmetrical result on the output. It is recommended to use the phase and frequency correct mode instead of the phase correct mode when changing the TOP value while the Timer/Counter is running. When using a static TOP value, there are practically no differences between the two modes of operation. In phase correct PWM mode, the compare units allow generation of PWM waveforms on the OC1x pins. Setting the COM1x1:0 bits to two will produce a non-inverted PWM and an inverted PWM output can be generated by setting the COM1x1:0 to three (See Table 47 on page 111). The actual OC1x value will only be visible on the port pin if the data direction for the port pin is set as output (DDR_OC1x). The PWM waveform is gener- ated by setting (or clearing) the OC1x Register at the Compare Match between OCR1x and TCNT1 when the counter increments, and clearing (or setting) the OC1x Register at Compare Match between OCR1x and TCNT1 when the counter decrements. The PWM frequency for the output when using phase correct PWM can be calculated by the fol- lowing equation: f clk_I/O f = ---------------------------- OCnxPCPWM 2⋅N⋅TOP The “N” variable represents the prescaler divider (1, 8, 64, 256, or 1024). The extreme values for the OCR1x Register represent special cases when generating a PWM waveform output in the phase correct PWM mode. If the OCR1x is set equal to BOTTOM the output will be continuously low and if set equal to TOP the output will be continuously high for non-inverted PWM mode. For inverted PWM the output will have the opposite logic values. If OCR1A is used to define the TOP value (WGM13:0 = 11) and COM1A1:0 = 1, the OC1A output will toggle with a 50% duty cycle. Phase and Frequency Correct The phase and frequency correct Pulse Width Modulation, or phase and frequency cor- PWM Mode rect PWM mode (WGM13:0 = 8 or 9) provides a high resolution phase and frequency correct PWM waveform generation option. The phase and frequency correct PWM mode is, like the phase correct PWM mode, based on a dual-slope operation. The counter counts repeatedly from BOTTOM (0x0000) to TOP and then from TOP to BOT- TOM. In non-inverting Compare Output mode, the Output Compare (OC1x) is cleared on the Compare Match between TCNT1 and OCR1x while up-counting, and set on the Compare Match while down-counting. In inverting Compare Output mode, the operation is inverted. The dual-slope operation gives a lower maximum operation frequency com- pared to the single-slope operation. However, due to the symmetric feature of the dual- slope PWM modes, these modes are preferred for motor control applications. The main difference between the phase correct and the phase and frequency correct PWM mode is the time the OCR1x Register is updated by the OCR1x Buffer Register, (see Figure 47 and Figure 48). The PWM resolution for the phase and frequency correct PWM mode can be defined by either ICR1 or OCR1A. The minimum resolution allowed is 2-bit (ICR1 or OCR1A set to 0x0003), and the maximum resolution is 16-bit (ICR1 or OCR1A set to MAX). The PWM resolution in bits can be calculated using the following equation: log(TOP+1) R = ----------------------------------- PFCPWM log(2) ATmega8535(L) 106 2502K–AVR–10/06
ATmega8535(L) In phase and frequency correct PWM mode the counter is incremented until the counter value matches either the value in ICR1 (WGM13:0 = 8), or the value in OCR1A (WGM13:0 = 9). The counter has then reached the TOP and changes the count direc- tion. The TCNT1 value will be equal to TOP for one timer clock cycle. The timing diagram for the phase correct and frequency correct PWM mode is shown in Figure 48. The figure shows phase and frequency correct PWM mode when OCR1A or ICR1 is used to define TOP. The TCNT1 value is in the timing diagram shown as a histogram for illustrating the dual-slope operation. The diagram includes non-inverted and inverted PWM outputs. The small horizontal line marks on the TCNT1 slopes represent compare matches between OCR1x and TCNT1. The OC1x Interrupt Flag will be set when a Com- pare Match occurs. Figure 48. Phase and Frequency Correct PWM Mode, Timing Diagram OCnA Interrupt Flag Set or ICFn Interrupt Flag Set (Interrupt on TOP) OCRnx/TOP Update and TOVn Interrupt Flag Set (Interrupt on Bottom) TCNTn OCnx (COMnx1:0 = 2) OCnx (COMnx1:0 = 3) Period 1 2 3 4 The Timer/Counter Overflow Flag (TOV1) is set at the same timer clock cycle as the OCR1x Registers are updated with the double buffer value (at BOTTOM). When either OCR1A or ICR1 is used for defining the TOP value, the OC1A or ICF1 Flag set when TCNT1 has reached TOP. The interrupt flags can then be used to generate an interrupt each time the counter reaches the TOP or BOTTOM value. When changing the TOP value the program must ensure that the new TOP value is higher or equal to the value of all of the compare registers. If the TOP value is lower than any of the compare registers, a Compare Match will never occur between the TCNT1 and the OCR1x. As Figure 48 shows the output generated is, in contrast to the phase correct mode, sym- metrical in all periods. Since the OCR1x Registers are updated at BOTTOM, the length of the rising and the falling slopes will always be equal. This gives symmetrical output pulses and the frequency is, therefore, correct. Using the ICR1 Register for defining TOP works well when using fixed TOP values. By using ICR1, the OCR1A Register is free to be used for generating a PWM output on OC1A. However, if the base PWM frequency is actively changed by changing the TOP value, using the OCR1A as TOP is clearly a better choice due to its double buffer feature. 107 2502K–AVR–10/06
In phase and frequency correct PWM mode, the compare units allow generation of PWM waveforms on the OC1x pins. Setting the COM1x1:0 bits to two will produce a non-inverted PWM and an inverted PWM output can be generated by setting the COM1x1:0 to three (see Table 47 on page 111). The actual OC1x value will only be vis- ible on the port pin if the data direction for the port pin is set as output (DDR_OC1x). The PWM waveform is generated by setting (or clearing) the OC1x Register at the Compare Match between OCR1x and TCNT1 when the counter increments, and clearing (or set- ting) the OC1x Register at Compare Match between OCR1x and TCNT1 when the counter decrements. The PWM frequency for the output when using phase and fre- quency correct PWM can be calculated by the following equation: f clk_I/O f = ---------------------------- OCnxPFCPWM 2⋅N⋅TOP The “N” variable represents the prescaler divider (1, 8, 64, 256, or 1024). The extreme values for the OCR1x Register represents special cases when generating a PWM waveform output in the phase correct PWM mode. If the OCR1x is set equal to BOTTOM the output will be continuously low and if set equal to TOP, the output will be set to high for non-inverted PWM mode. For inverted PWM, the output will have the opposite logic values. If OCR1A is used to define the TOP value (WGM13:0 = 9) and COM1A1:0 = 1, the OC1A output will toggle with a 50% duty cycle. Timer/Counter Timing The Timer/Counter is a synchronous design and the timer clock (clk ) is therefore T1 Diagrams shown as a clock enable signal in the following figures. The figures include information on when interrupt flags are set, and when the OCR1x Register is updated with the OCR1x buffer value (only for modes utilizing double buffering). Figure 49 shows a timing diagram for the setting of OCF1x. Figure 49. Timer/Counter Timing Diagram, Setting of OCF1x, no Prescaling clk I/O clk Tn (clk /1) I/O TCNTn OCRnx - 1 OCRnx OCRnx + 1 OCRnx + 2 OCRnx OCRnx Value OCFnx Figure 50 shows the same timing data, but with the prescaler enabled. ATmega8535(L) 108 2502K–AVR–10/06
ATmega8535(L) Figure 50. Timer/Counter Timing Diagram, Setting of OCF1x, with Prescaler (f /8) clk_I/O clk I/O clk Tn (clk /8) I/O TCNTn OCRnx - 1 OCRnx OCRnx + 1 OCRnx + 2 OCRnx OCRnx Value OCFnx Figure 51 shows the count sequence close to TOP in various modes. When using phase and frequency correct PWM mode, the OCR1x Register is updated at BOTTOM. The timing diagrams will be the same, but TOP should be replaced by BOTTOM, TOP-1 by BOTTOM+1 and so on. The same renaming applies for modes that set the TOV1 Flag at BOTTOM. Figure 51. Timer/Counter Timing Diagram, no Prescaling clk I/O clk Tn (clk /1) I/O TCNTn TOP - 1 TOP BOTTOM BOTTOM + 1 (CTC and FPWM) TCNTn TOP - 1 TOP TOP - 1 TOP - 2 (PC and PFC PWM) TOVn (FPWM) and ICFn (if used as TOP) OCRnx Old OCRnx Value New OCRnx Value (Update at TOP) Figure 52 shows the same timing data, but with the prescaler enabled. 109 2502K–AVR–10/06
Figure 52. Timer/Counter Timing Diagram, with Prescaler (f /8) clk_I/O clk I/O clk Tn (clk /8) I/O TCNTn TOP - 1 TOP BOTTOM BOTTOM + 1 (CTC and FPWM) TCNTn TOP - 1 TOP TOP - 1 TOP - 2 (PC and PFC PWM) TOVn (FPWM) and ICFn (if used as TOP) OCRnx Old OCRnx Value New OCRnx Value (Update at TOP) 16-bit Timer/Counter Register Description Timer/Counter1 Control Register A – TCCR1A Bit 7 6 5 4 3 2 1 0 COM1A1 COM1A0 COM1B1 COM1B0 FOC1A FOC1B WGM11 WGM10 TCCR1A Read/Write R/W R/W R/W R/W W W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 7:6 – COM1A1:0: Compare Output Mode for Channel A (cid:129) Bit 5:4 – COM1B1:0: Compare Output Mode for Channel B The COM1A1:0 and COM1B1:0 control the Output Compare pins (OC1A and OC1B respectively) behavior. If one or both of the COM1A1:0 bits are written to one, the OC1A output overrides the normal port functionality of the I/O pin it is connected to. If one or both of the COM1B1:0 bit are written to one, the OC1B output overrides the normal port functionality of the I/O pin it is connected to. However, note that the Data Direction Reg- ister (DDR) bit corresponding to the OC1A or OC1B pin must be set in order to enable the output driver. When the OC1A or OC1B is connected to the pin, the function of the COM1x1:0 bits is dependent of the WGM13:0 bits setting. Table 45 shows the COM1x1:0 bit functionality when the WGM13:0 bits are set to a normal or a CTC mode (non-PWM). Table 45. Compare Output Mode, non-PWM COM1A1/ COM1A0/ COM1B1 COM1B0 Description 0 0 Normal port operation, OC1A/OC1B disconnected. 0 1 Toggle OC1A/OC1B on Compare Match. 1 0 Clear OC1A/OC1B on Compare Match (set output to low level). 1 1 Set OC1A/OC1B on Compare Match (set output to high level). ATmega8535(L) 110 2502K–AVR–10/06
ATmega8535(L) Table 46 shows the COM1x1:0 bit functionality when the WGM13:0 bits are set to the fast PWM mode. Table 46. Compare Output Mode, Fast PWM(1) COM1A1/ COM1A0/ COM1B1 COM1B0 Description 0 0 Normal port operation, OC1A/OC1B disconnected. 0 1 WGM13:0 = 15: Toggle OC1A on Compare Match, OC1B disconnected (normal port operation). For all other WGM1 settings, normal port operation OC1A/OC1B disconnected. 1 0 Clear OC1A/OC1B on Compare Match, set OC1A/OC1B at TOP (Non-Inverting) 1 1 Set OC1A/OC1B on Compare Match, clear OC1A/OC1B at TOP (Inverting) Note: 1. A special case occurs when OCR1A/OCR1B equals TOP and COM1A1/COM1B1 is set. In this case the Compare Match is ignored, but the set or clear is done at TOP. See “Fast PWM Mode” on page 102 for more details. Table 47 shows the COM1x1:0 bit functionality when the WGM13:0 bits are set to the phase correct or the phase and frequency correct, PWM mode. Table 47. Compare Output Mode, Phase Correct and Phase and Frequency Correct PWM(1) COM1A1/ COM1A0/ COM1B1 COM1B0 Description 0 0 Normal port operation, OC1A/OC1B disconnected. 0 1 WGM13:0 = 9 or 14: Toggle OC1A on Compare Match, OC1B disconnected (normal port operation). For all other WGM1 settings, normal port operation, OC1A/OC1B disconnected. 1 0 Clear OC1A/OC1B on Compare Match when up-counting. Set OC1A/OC1B on Compare Match when down-counting. 1 1 Set OC1A/OC1B on Compare Match when up-counting. Clear OC1A/OC1B on Compare Match when down-counting. Note: 1. A special case occurs when OCR1A/OCR1B equals TOP and COM1A1/COM1B1 is set. See “Phase Correct PWM Mode” on page 104. for more details. (cid:129) Bit 3 – FOC1A: Force Output Compare for Channel A (cid:129) Bit 2 – FOC1B: Force Output Compare for Channel B The FOC1A/FOC1B bits are only active when the WGM13:0 bits specify a non-PWM mode. However, for ensuring compatibility with future devices, these bits must be set to zero when TCCR1A is written when operating in a PWM mode. When writing a logical one to the FOC1A/FOC1B bit, an immediate Compare Match is forced on the waveform generation unit. The OC1A/OC1B output is changed according to its COM1x1:0 bits set- ting. Note that the FOC1A/FOC1B bits are implemented as strobes. Therefore it is the value present in the COM1x1:0 bits that determine the effect of the forced compare. A FOC1A/FOC1B strobe will not generate any interrupt nor will it clear the timer in Clear Timer on Compare Match (CTC) mode using OCR1A as TOP. The FOC1A/FOC1B bits are always read as zero. (cid:129) Bit 1:0 – WGM11:0: Waveform Generation Mode 111 2502K–AVR–10/06
Combined with the WGM13:2 bits found in the TCCR1B Register, these bits control the counting sequence of the counter, the source for maximum (TOP) counter value, and what type of waveform generation to be used, see Table 48. Modes of operation supported by the Timer/Counter unit are: Normal mode (counter), Clear Timer on Compare Match (CTC) mode, and three types of Pulse Width Modulation (PWM) modes. See “Modes of Operation” on page 101. Table 48. Waveform Generation Mode Bit Description(1) WGM12 WGM11 WGM10 Timer/Counter Mode of Update of TOV1 Flag Mode WGM13 (CTC1) (PWM11) (PWM10) Operation TOP OCR1x at Set on 0 0 0 0 0 Normal 0xFFFF Immediate MAX 1 0 0 0 1 PWM, Phase Correct, 8-bit 0x00FF TOP BOTTOM 2 0 0 1 0 PWM, Phase Correct, 9-bit 0x01FF TOP BOTTOM 3 0 0 1 1 PWM, Phase Correct, 10-bit 0x03FF TOP BOTTOM 4 0 1 0 0 CTC OCR1A Immediate MAX 5 0 1 0 1 Fast PWM, 8-bit 0x00FF BOTTOM TOP 6 0 1 1 0 Fast PWM, 9-bit 0x01FF BOTTOM TOP 7 0 1 1 1 Fast PWM, 10-bit 0x03FF BOTTOM TOP 8 1 0 0 0 PWM, Phase and Frequency Correct ICR1 BOTTOM BOTTOM 9 1 0 0 1 PWM, Phase and Frequency Correct OCR1A BOTTOM BOTTOM 10 1 0 1 0 PWM, Phase Correct ICR1 TOP BOTTOM 11 1 0 1 1 PWM, Phase Correct OCR1A TOP BOTTOM 12 1 1 0 0 CTC ICR1 Immediate MAX 13 1 1 0 1 Reserved – – – 14 1 1 1 0 Fast PWM ICR1 BOTTOM TOP 15 1 1 1 1 Fast PWM OCR1A BOTTOM TOP Note: 1. The CTC1 and PWM11:0 bit definition names are obsolete. Use the WGM12:0 definitions. However, the functionality and location of these bits are compatible with previous versions of the timer. ATmega8535(L) 112 2502K–AVR–10/06
ATmega8535(L) Timer/Counter1 Control Register B – TCCR1B Bit 7 6 5 4 3 2 1 0 ICNC1 ICES1 – WGM13 WGM12 CS12 CS11 CS10 TCCR1B Read/Write R/W R/W R R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 7 – ICNC1: Input Capture Noise Canceler Setting this bit (to one) activates the Input Capture Noise Canceler. When the Noise Canceler is activated, the input from the Input Capture Pin (ICP1) is filtered. The filter function requires four successive equal valued samples of the ICP1 pin for changing its output. The Input Capture is therefore delayed by four oscillator cycles when the noise canceler is enabled. (cid:129) Bit 6 – ICES1: Input Capture Edge Select This bit selects which edge on the Input Capture Pin (ICP1) is used to trigger a capture event. When the ICES1 bit is written to zero, a falling (negative) edge is used as trigger, and when the ICES1 bit is written to one, a rising (positive) edge will trigger the capture. When a capture is triggered according to the ICES1 setting, the counter value is copied into the Input Capture Register (ICR1). The event will also set the Input Capture Flag (ICF1), and this can be used to cause an Input Capture Interrupt, if this interrupt is enabled. When the ICR1 is used as TOP value (see description of the WGM13:0 bits located in the TCCR1A and the TCCR1B Register), the ICP1 is disconnected, and consequently, the Input Capture function is disabled. (cid:129) Bit 5 – Reserved Bit This bit is reserved for future use. For ensuring compatibility with future devices, this bit must be written to zero when TCCR1B is written. (cid:129) Bit 4:3 – WGM13:2: Waveform Generation Mode See TCCR1A Register description. (cid:129) Bit 2:0 – CS12:0: Clock Select The three Clock Select bits select the clock source to be used by the Timer/Counter, see Figure 49 and Figure 50. Table 49. Clock Select Bit Description CS12 CS11 CS10 Description 0 0 0 No clock source (Timer/Counter stopped). 0 0 1 clk /1 (No prescaling) I/O 0 1 0 clk /8 (From prescaler) I/O 0 1 1 clk /64 (From prescaler) I/O 1 0 0 clk /256 (From prescaler) I/O 1 0 1 clk /1024 (From prescaler) I/O 1 1 0 External clock source on T1 pin. Clock on falling edge. 1 1 1 External clock source on T1 pin. Clock on rising edge. If external pin modes are used for the Timer/Counter1, transitions on the T1 pin will clock the counter even if the pin is configured as an output. This feature allows software control of the counting. 113 2502K–AVR–10/06
Timer/Counter1 – TCNT1H and TCNT1L Bit 7 6 5 4 3 2 1 0 TCNT1[15:8] TCNT1H TCNT1[7:0] TCNT1L Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 The two Timer/Counter I/O locations (TCNT1H and TCNT1L, combined TCNT1) give direct access, both for read and for write operations, to the Timer/Counter unit 16-bit counter. To ensure that both the high and low bytes are read and written simultaneously when the CPU accesses these registers, the access is performed using an 8-bit tempo- rary high byte register (TEMP). This temporary register is shared by all the other 16-bit registers. See “Accessing 16-bit Registers” on page 92. Modifying the counter (TCNT1) while the counter is running introduces a risk of missing a Compare Match between TCNT1 and one of the OCR1x Registers. Writing to the TCNT1 Register blocks (removes) the Compare Match on the following timer clock for all compare units. Output Compare Register 1 A – OCR1AH and OCR1AL Bit 7 6 5 4 3 2 1 0 OCR1A[15:8] OCR1AH OCR1A[7:0] OCR1AL Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 Output Compare Register 1 B – OCR1BH and OCR1BL Bit 7 6 5 4 3 2 1 0 OCR1B[15:8] OCR1BH OCR1B[7:0] OCR1BL Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 The Output Compare Registers contain a 16-bit value that is continuously compared with the counter value (TCNT1). A match can be used to generate an output compare interrupt, or to generate a waveform output on the OC1x pin. The Output Compare Registers are 16-bit in size. To ensure that both the high and low bytes are written simultaneously when the CPU writes to these registers, the access is performed using an 8-bit temporary high byte register (TEMP). This temporary register is shared by all the other 16-bit registers. See “Accessing 16-bit Registers” on page 92. Input Capture Register 1 – ICR1H and ICR1L Bit 7 6 5 4 3 2 1 0 ICR1[15:8] ICR1H ICR1[7:0] ICR1L Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 The Input Capture is updated with the counter (TCNT1) value each time an event occurs on the ICP1 pin (or optionally on the Analog Comparator output for Timer/Counter1). The Input Capture can be used for defining the counter TOP value. The Input Capture Register is 16-bit in size. To ensure that both the high and low bytes are read simultaneously when the CPU accesses these registers, the access is per- formed using an 8-bit temporary high byte register (TEMP). This temporary register is shared by all the other 16-bit registers. See “Accessing 16-bit Registers” on page 92. ATmega8535(L) 114 2502K–AVR–10/06
ATmega8535(L) Timer/Counter Interrupt Mask Register – TIMSK(1) Bit 7 6 5 4 3 2 1 0 OCIE2 TOIE2 TICIE1 OCIE1A OCIE1B TOIE1 OCIE0 TOIE0 TIMSK Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 Note: 1. This register contains interrupt control bits for several Timer/Counters, but only Timer1 bits are described in this section. The remaining bits are described in their respective timer sections. (cid:129) Bit 5 – TICIE1: Timer/Counter1, Input Capture Interrupt Enable When this bit is written to one and the I-flag in the Status Register is set (interrupts glo- bally enabled), the Timer/Counter1 Input Capture interrupt is enabled. The corresponding Interrupt Vector (see “Interrupts” on page 46) is executed when the ICF1 Flag, located in TIFR, is set. (cid:129) Bit 4 – OCIE1A: Timer/Counter1, Output Compare A Match Interrupt Enable When this bit is written to one and the I-flag in the Status Register is set (interrupts glo- bally enabled), the Timer/Counter1 output compare A match interrupt is enabled. The corresponding Interrupt Vector (see “Interrupts” on page 46) is executed when the OCF1A Flag, located in TIFR, is set. (cid:129) Bit 3 – OCIE1B: Timer/Counter1, Output Compare B Match Interrupt Enable When this bit is written to one and the I-flag in the Status Register is set (interrupts glo- bally enabled), the Timer/Counter1 output compare B match interrupt is enabled. The corresponding Interrupt Vector (see “Interrupts” on page 46) is executed when the OCF1B Flag, located in TIFR, is set. (cid:129) Bit 2 – TOIE1: Timer/Counter1, Overflow Interrupt Enable When this bit is written to one and the I-flag in the Status Register is set (interrupts glo- bally enabled), the Timer/Counter1 overflow interrupt is enabled. The corresponding Interrupt Vector (see “Interrupts” on page 46) is executed when the TOV1 Flag, located in TIFR, is set. 115 2502K–AVR–10/06
Timer/Counter Interrupt Flag Register – TIFR(1) Bit 7 6 5 4 3 2 1 0 OCF2 TOV2 ICF1 OCF1A OCF1B TOV1 OCF0 TOV0 TIFR Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 Note: 1. This register contains flag bits for several Timer/Counters, but only Timer1 bits are described in this section. The remaining bits are described in their respective timer sections. (cid:129) Bit 5 – ICF1: Timer/Counter1, Input Capture Flag This flag is set when a capture event occurs on the ICP1 pin. When the Input Capture Register (ICR1) is set by the WGM13:0 to be used as the TOP value, the ICF1 Flag is set when the counter reaches the TOP value. ICF1 is automatically cleared when the Input Capture Interrupt Vector is executed. Alter- natively, ICF1 can be cleared by writing a logic one to its bit location. (cid:129) Bit 4 – OCF1A: Timer/Counter1, Output Compare A Match Flag This flag is set in the timer clock cycle after the counter (TCNT1) value matches the Out- put Compare Register A (OCR1A). Note that a Forced Output Compare (FOC1A) strobe will not set the OCF1A Flag. OCF1A is automatically cleared when the Output Compare Match A Interrupt Vector is executed. Alternatively, OCF1A can be cleared by writing a logic one to its bit location. (cid:129) Bit 3 – OCF1B: Timer/Counter1, Output Compare B Match Flag This flag is set in the timer clock cycle after the counter (TCNT1) value matches the Out- put Compare Register B (OCR1B). Note that a Forced Output Compare (FOC1B) strobe will not set the OCF1B Flag. OCF1B is automatically cleared when the Output Compare Match B Interrupt Vector is executed. Alternatively, OCF1B can be cleared by writing a logic one to its bit location. (cid:129) Bit 2 – TOV1: Timer/Counter1, Overflow Flag The setting of this flag is dependent of the WGM13:0 bits setting. In normal and CTC modes, the TOV1 Flag is set when the timer overflows. Refer to Table 48 on page 112 for the TOV1 Flag behavior when using another WGM13:0 bit setting. TOV1 is automatically cleared when the Timer/Counter1 Overflow Interrupt Vector is executed. Alternatively, TOV1 can be cleared by writing a logic one to its bit location. ATmega8535(L) 116 2502K–AVR–10/06
ATmega8535(L) 8-bit Timer/Counter2 Timer/Counter2 is a general purpose, single channel, 8-bit Timer/Counter module. The with PWM and main features are: (cid:129) Single Channel Counter Asynchronous (cid:129) Clear Timer on Compare Match (Auto Reload) Operation (cid:129) Glitch-free, Phase Correct Pulse Width Modulator (PWM) (cid:129) Frequency Generator (cid:129) 10-bit Clock Prescaler (cid:129) Overflow and Compare Match Interrupt Sources (TOV2 and OCF2) (cid:129) Allows Clocking from External 32 kHz Watch Crystal Independent of the I/O Clock Overview A simplified block diagram of the 8-bit Timer/Counter is shown in Figure 53. For the actual placement of I/O pins, refer to “Pinout ATmega8535” on page 2. CPU accessible I/O Registers, including I/O bits and I/O pins, are shown in bold. The device-specific I/O Register and bit locations are listed in the “8-bit Timer/Counter Register Description” on page 128. Figure 53. 8-bit Timer/Counter Block Diagram TCCRn count TOVn clear (Int.Req.) Control Logic direction clk Tn TOSC1 BOTTOM TOP T/C Prescaler Oscillator TOSC2 Timer/Counter TCNTn = 0 = 0xFF OCn clkI/O (Int.Req.) = Waveform OCn Generation OCRn S U B A T A D clk Synchronized Status Flags I/O Synchronization Unit clk ASY Status Flags ASSRn Asynchronous Mode Select (ASn) 117 2502K–AVR–10/06
Registers The Timer/Counter (TCNT2) and Output Compare Register (OCR2) are 8-bit registers. Interrupt request (shorten as Int.Req.) signals are all visible in the Timer Interrupt Flag Register (TIFR). All interrupts are individually masked with the Timer Interrupt Mask Register (TIMSK). TIFR and TIMSK are not shown in the figure since these registers are shared by other timer units. The Timer/Counter can be clocked internally, via the prescaler, or asynchronously clocked from the TOSC1/2 pins, as detailed later in this section. The asynchronous operation is controlled by the Asynchronous Status Register (ASSR). The Clock Select logic block controls which clock source the Timer/Counter uses to increment (or decre- ment) its value. The Timer/Counter is inactive when no clock source is selected. The output from the Clock Select logic is referred to as the timer clock (clk ). T2 The double buffered Output Compare Register (OCR2) is compared with the Timer/Counter value at all times. The result of the compare can be used by the Wave- form Generator to generate a PWM or variable frequency output on the Output Compare Pin (OC2). See “Output Compare Unit” on page 119 for details. The Compare Match event will also set the Compare Flag (OCF2) which can be used to generate an output compare interrupt request. Definitions Many register and bit references in this section are written in general form. A lower case “n” replaces the Timer/Counter number, in this case 2. However, when using the register or bit defines in a program, the precise form must be used (i.e., TCNT2 for accessing Timer/Counter2 counter value and so on). The definitions in Table 50 are also used extensively throughout this section. Table 50. Definitions BOTTOM The counter reaches the BOTTOM when it becomes zero (0x00). MAX The counter reaches its MAXimum when it becomes 0xFF (decimal 255). TOP The counter reaches the TOP when it becomes equal to the highest value in the count sequence. The TOP value can be assigned to be the fixed value 0xFF (MAX) or the value stored in the OCR2 Register. The assignment is dependent on the mode of operation. Timer/Counter Clock The Timer/Counter can be clocked by an internal synchronous or an external asynchro- Sources nous clock source. The clock source clk is by default equal to the MCU clock, clk . T2 I/O When the AS2 bit in the ASSR Register is written to logic one, the clock source is taken from the Timer/Counter Oscillator connected to TOSC1 and TOSC2. For details on asynchronous operation, see “Asynchronous Status Register – ASSR” on page 131. For details on clock sources and prescaler, see “Timer/Counter Prescaler” on page 134. ATmega8535(L) 118 2502K–AVR–10/06
ATmega8535(L) Counter Unit The main part of the 8-bit Timer/Counter is the programmable bi-directional counter unit. Figure 54 shows a block diagram of the counter and its surrounding environment. Figure 54. Counter Unit Block Diagram TOVn (Int.Req.) DATA BUS TOSC1 count T/C TCNTn clear Control Logic clkTn Prescaler Oscillator direction TOSC2 clk bottom top I/O Signal description (internal signals): count Increment or decrement TCNT2 by 1. direction Selects between increment and decrement. clear Clear TCNT2 (set all bits to zero). clk Timer/Counter clock. T2 top Signalizes that TCNT2 has reached maximum value. bottom Signalizes that TCNT2 has reached minimum value (zero). Depending on the mode of operation used, the counter is cleared, incremented, or dec- remented at each timer clock (clk ). clk can be generated from an external or internal T2 T2 clock source, selected by the Clock Select bits (CS22:0). When no clock source is selected (CS22:0 = 0) the timer is stopped. However, the TCNT2 value can be accessed by the CPU, regardless of whether clk is present or not. A CPU write overrides (has T2 priority over) all counter clear or count operations. The counting sequence is determined by the setting of the WGM21 and WGM20 bits located in the Timer/Counter Control Register (TCCR2). There are close connections between how the counter behaves (counts) and how waveforms are generated on the output compare output OC2. For more details about advanced counting sequences and waveform generation, see “Modes of Operation” on page 122. The Timer/Counter Overflow Flag (TOV2) is set according to the mode of operation selected by the WGM21:0 bits. TOV2 can be used for generating a CPU interrupt. Output Compare Unit The 8-bit comparator continuously compares TCNT2 with the Output Compare Register (OCR2). Whenever TCNT2 equals OCR2, the comparator signals a match. A match will set the Output Compare Flag (OCF2) at the next timer clock cycle. If enabled (OCIE2 = 1), the Output Compare Flag generates an output compare interrupt. The OCF2 Flag is automatically cleared when the interrupt is executed. Alternatively, the OCF2 Flag can be cleared by software by writing a logical one to its I/O bit location. The Waveform Gen- erator uses the match signal to generate an output according to operating mode set by the WGM21:0 bits and Compare Output mode (COM21:0) bits. The max and bottom sig- nals are used by the Waveform Generator for handling the special cases of the extreme values in some modes of operation (see “Modes of Operation” on page 122). Figure 55 shows a block diagram of the output compare unit. 119 2502K–AVR–10/06
Figure 55. Output Compare Unit, Block Diagram DATA BUS OCRn TCNTn = (8-bit Comparator ) OCFn (Int.Req.) top bottom Waveform Generator OCxy FOCn WGMn1:0 COMn1:0 The OCR2 Register is double buffered when using any of the pulse width modulation (PWM) modes. For the normal and Clear Timer on Compare (CTC) modes of operation, the double buffering is disabled. The double buffering synchronizes the update of the OCR2 Compare Register to either top or bottom of the counting sequence. The synchro- nization prevents the occurrence of odd-length, non-symmetrical PWM pulses, thereby making the output glitch-free. The OCR2 Register access may seem complex, but this is not the case. When the dou- ble buffering is enabled, the CPU has access to the OCR2 Buffer Register, and if double buffering is disabled the CPU will access the OCR2 directly. Force Output Compare In non-PWM waveform generation modes, the match output of the comparator can be forced by writing a one to the Force Output Compare (FOC2) bit. Forcing Compare Match will not set the OCF2 Flag or reload/clear the timer, but the OC2 pin will be updated as if a real Compare Match had occurred (the COM21:0 bits settings define whether the OC2 pin is set, cleared or toggled). Compare Match Blocking by All CPU write operations to the TCNT2 Register will block any Compare Match that TCNT2 Write occurs in the next timer clock cycle, even when the timer is stopped. This feature allows OCR2 to be initialized to the same value as TCNT2 without triggering an interrupt when the Timer/Counter clock is enabled. Using the Output Compare Since writing TCNT2 in any mode of operation will block all compare matches for one Unit timer clock cycle, there are risks involved when changing TCNT2 when using the output compare channel, independently of whether the Timer/Counter is running or not. If the value written to TCNT2 equals the OCR2 value, the Compare Match will be missed, resulting in incorrect waveform generation. Similarly, do not write the TCNT2 value equal to BOTTOM when the counter is down-counting. The setup of the OC2 should be performed before setting the Data Direction Register for the port pin to output. The easiest way of setting the OC2 value is to use the force output compare (FOC2) strobe bit in Normal mode. The OC2 Register keeps its value even when changing between Waveform Generation modes. ATmega8535(L) 120 2502K–AVR–10/06
ATmega8535(L) Be aware that the COM21:0 bits are not double buffered together with the compare value. Changing the COM21:0 bits will take effect immediately. Compare Match Output The Compare Output mode (COM21:0) bits have two functions. The Waveform Genera- Unit tor uses the COM21:0 bits for defining the Output Compare (OC2) state at the next Compare Match. Also, the COM21:0 bits control the OC2 pin output source. Figure 56 shows a simplified schematic of the logic affected by the COM21:0 bit setting. The I/O Registers, I/O bits, and I/O pins in the figure are shown in bold. Only the parts of the general I/O port control registers (DDR and PORT) that are affected by the COM21:0 bits are shown. When referring to the OC2 state, the reference is for the internal OC2 Register, not the OC2 pin. Figure 56. Compare Match Output Unit, Schematic COMn1 Waveform COMn0 D Q Generator FOCn 1 OCn OCn Pin 0 D Q S U B PORT A T A D D Q DDR clk I/O The general I/O port function is overridden by the Output Compare (OC2) from the waveform generator if either of the COM21:0 bits are set. However, the OC2 pin direc- tion (input or output) is still controlled by the Data Direction Register (DDR) for the port pin. The Data Direction Register bit for the OC2 pin (DDR_OC2) must be set as output before the OC2 value is visible on the pin. The port override function is independent of the Waveform Generation mode. The design of the output compare pin logic allows initialization of the OC2 state before the output is enabled. Note that some COM21:0 bit settings are reserved for certain modes of operation. See “8-bit Timer/Counter Register Description” on page 128. Compare Output Mode and The Waveform Generator uses the COM21:0 bits differently in normal, CTC, and PWM Waveform Generation modes. For all modes, setting the COM21:0 = 0 tells the waveform generator that no action on the OC2 Register is to be performed on the next Compare Match. For com- pare output actions in the non-PWM modes refer to Table 52 on page 129. For fast PWM mode, refer to Table 53 on page 129, and for phase correct PWM refer to Table 54 on page 130. 121 2502K–AVR–10/06
A change of the COM21:0 bits state will take effect at the first Compare Match after the bits are written. For non-PWM modes, the action can be forced to have an immediate effect by using the FOC2 strobe bits. Modes of Operation The mode of operation (i.e., the behavior of the Timer/Counter and the Output Compare pins) is defined by the combination of the Waveform Generation mode (WGM21:0) and Compare Output mode (COM21:0) bits. The Compare Output mode bits do not affect the counting sequence, while the Waveform Generation mode bits do. The COM21:0 bits control whether the PWM output generated should be inverted or not (inverted or non-inverted PWM). For non-PWM modes the COM21:0 bits control whether the output should be set, cleared, or toggled at a Compare Match (See “Compare Match Output Unit” on page 121.). For detailed timing information refer to “Timer/Counter Timing Diagrams” on page 126. Normal Mode The simplest mode of operation is the Normal mode (WGM21:0 = 0). In this mode the counting direction is always up (incrementing), and no counter clear is performed. The counter simply overruns when it passes its maximum 8-bit value (TOP = 0xFF) and then restarts from the bottom (0x00). In normal operation the Timer/Counter Overflow Flag (TOV2) will be set in the same timer clock cycle as the TCNT2 becomes zero. The TOV2 Flag in this case behaves like a ninth bit, except that it is only set, not cleared. However, combined with the timer overflow interrupt that automatically clears the TOV2 Flag, the timer resolution can be increased by software. There are no special cases to consider in the normal mode, a new counter value can be written anytime. The output compare unit can be used to generate interrupts at some given time. Using the output compare to generate waveforms in Normal mode is not recommended, since this will occupy too much of the CPU time. Clear Timer on Compare In Clear Timer on Compare or CTC mode (WGM21:0 = 2), the OCR2 Register is used to Match (CTC) Mode manipulate the counter resolution. In CTC mode, the counter is cleared to zero when the counter value (TCNT2) matches the OCR2. The OCR2 defines the top value for the counter, hence also its resolution. This mode allows greater control of the Compare Match output frequency. It also simplifies the operation of counting external events. The timing diagram for the CTC mode is shown in Figure 57. The counter value (TCNT2) increases until a Compare Match occurs between TCNT2 and OCR2, and then counter (TCNT2) is cleared. Figure 57. CTC Mode, Timing Diagram OCn Interrupt Flag Set TCNTn OCn (COMn1:0 = 1) (Toggle) Period 1 2 3 4 ATmega8535(L) 122 2502K–AVR–10/06
ATmega8535(L) An interrupt can be generated each time the counter value reaches the TOP value by using the OCF2 Flag. If the interrupt is enabled, the interrupt handler routine can be used for updating the TOP value. However, changing the TOP to a value close to BOT- TOM when the counter is running with none or a low prescaler value must be done with care since the CTC mode does not have the double buffering feature. If the new value written to OCR2 is lower than the current value of TCNT2, the counter will miss the Compare Match. The counter will then have to count to its maximum value (0xFF) and wrap around starting at 0x00 before the Compare Match can occur. For generating a waveform output in CTC mode, the OC2 output can be set to toggle its logical level on each Compare Match by setting the Compare Output mode bits to toggle mode (COM21:0 = 1). The OC2 value will not be visible on the port pin unless the data direction for the pin is set to output. The waveform generated will have a maximum fre- quency of f = f /2 when OCR2 is set to zero (0x00). The waveform frequency is OC2 clk_I/O defined by the following equation: f clk_I/O f = ----------------------------------------------- OCn 2⋅N⋅(1+OCRn) The “N” variable represents the prescale factor (1, 8, 32, 64, 128, 256, or 1024). As for the Normal mode of operation, the TOV2 Flag is set in the same timer clock cycle that the counter counts from MAX to 0x00. Fast PWM Mode The fast Pulse Width Modulation or fast PWM mode (WGM21:0 = 3) provides a high fre- quency PWM waveform generation option. The fast PWM differs from the other PWM option by its single-slope operation. The counter counts from BOTTOM to MAX then restarts from BOTTOM. In non-inverting Compare Output mode, the Output Compare (OC2) is cleared on the Compare Match between TCNT2 and OCR2, and set at BOT- TOM. In inverting Compare Output mode, the output is set on Compare Match and cleared at BOTTOM. Due to the single-slope operation, the operating frequency of the fast PWM mode can be twice as high as the phase correct PWM mode that uses dual- slope operation. This high frequency makes the fast PWM mode well suited for power regulation, rectification, and DAC applications. High frequency allows physically small sized external components (coils, capacitors), and therefore reduces total system cost. In fast PWM mode, the counter is incremented until the counter value matches the MAX value. The counter is then cleared at the following timer clock cycle. The timing diagram for the fast PWM mode is shown in Figure 58. The TCNT2 value is in the timing diagram shown as a histogram for illustrating the single-slope operation. The diagram includes non-inverted and inverted PWM outputs. The small horizontal line marks on the TCNT2 slopes represent compare matches between OCR2 and TCNT2. 123 2502K–AVR–10/06
Figure 58. Fast PWM Mode, Timing Diagram OCRn Interrupt Flag Set OCRn Update and TOVn Interrupt Flag Set TCNTn OCn (COMn1:0 = 2) OCn (COMn1:0 = 3) Period 1 2 3 4 5 6 7 The Timer/Counter Overflow Flag (TOV2) is set each time the counter reaches MAX. If the interrupt is enabled, the interrupt handler routine can be used for updating the com- pare value. In fast PWM mode, the compare unit allows generation of PWM waveforms on the OC2 pin. Setting the COM21:0 bits to two will produce a non-inverted PWM and an inverted PWM output can be generated by setting the COM21:0 to three (See Table 53 on page 129). The actual OC2 value will only be visible on the port pin if the data direction for the port pin is set as output. The PWM waveform is generated by setting (or clearing) the OC2 Register at the Compare Match between OCR2 and TCNT2, and clearing (or set- ting) the OC2 Register at the timer clock cycle the counter is cleared (changes from MAX to BOTTOM). The PWM frequency for the output can be calculated by the following equation: f clk_I/O f = ------------------ OCnPWM N⋅256 The “N” variable represents the prescale factor (1, 8, 32, 64, 128, 256, or 1024). The extreme values for the OCR2 Register represent special cases when generating a PWM waveform output in the fast PWM mode. If the OCR2 is set equal to BOTTOM, the output will be a narrow spike for each MAX+1 timer clock cycle. Setting the OCR2 equal to MAX will result in a constantly high or low output (depending on the polarity of the out- put set by the COM21:0 bits.) A frequency (with 50% duty cycle) waveform output in fast PWM mode can be achieved by setting OC2 to toggle its logical level on each Compare Match (COM21:0 = 1). The waveform generated will have a maximum frequency of f = f /2 when OCR2 is set oc2 clk_I/O to zero. This feature is similar to the OC2 toggle in CTC mode, except the double buffer feature of the output compare unit is enabled in the fast PWM mode. ATmega8535(L) 124 2502K–AVR–10/06
ATmega8535(L) Phase Correct PWM Mode The Phase Correct PWM mode (WGM21:0 = 1) provides a high resolution phase correct PWM waveform generation option. The phase correct PWM mode is based on a dual- slope operation. The counter counts repeatedly from BOTTOM to MAX and then from MAX to BOTTOM. In non-inverting Compare Output mode, the Output Compare (OC2) is cleared on the Compare Match between TCNT2 and OCR2 while up-counting, and set on the Compare Match while down-counting. In inverting output compare mode, the operation is inverted. The dual-slope operation has lower maximum operation frequency than single slope operation. However, due to the symmetric feature of the dual-slope PWM modes, these modes are preferred for motor control applications. The PWM resolution for the phase correct PWM mode is fixed to eight bits. In phase correct PWM mode the counter is incremented until the counter value matches MAX. When the counter reaches MAX, it changes the count direction. The TCNT2 value will be equal to MAX for one timer clock cycle. The timing diagram for the phase correct PWM mode is shown on Figure 59. The TCNT2 value is in the timing diagram shown as a histogram for illustrating the dual-slope operation. The diagram includes non-inverted and inverted PWM outputs. The small horizontal line marks on the TCNT2 slopes repre- sent compare matches between OCR2 and TCNT2. Figure 59. Phase Correct PWM Mode, Timing Diagram OCn Interrupt Flag Set OCRn Update TOVn Interrupt Flag Set TCNTn OCn (COMn1:0 = 2) OCn (COMn1:0 = 3) Period 1 2 3 The Timer/Counter Overflow Flag (TOV2) is set each time the counter reaches BOT- TOM. The Interrupt Flag can be used to generate an interrupt each time the counter reaches the BOTTOM value. In phase correct PWM mode, the compare unit allows generation of PWM waveforms on the OC2 pin. Setting the COM21:0 bits to two will produce a non-inverted PWM. An inverted PWM output can be generated by setting the COM21:0 to three (See Table 54 on page 130). The actual OC2 value will only be visible on the port pin if the data direc- tion for the port pin is set as output. The PWM waveform is generated by clearing (or setting) the OC2 Register at the Compare Match between OCR2 and TCNT2 when the counter increments, and setting (or clearing) the OC2 Register at Compare Match 125 2502K–AVR–10/06
between OCR2 and TCNT2 when the counter decrements. The PWM frequency for the output when using phase correct PWM can be calculated by the following equation: f clk_I/O f = ------------------ OCnPCPWM N⋅510 The “N” variable represents the prescale factor (1, 8, 32, 64, 128, 256, or 1024). The extreme values for the OCR2 Register represent special cases when generating a PWM waveform output in the phase correct PWM mode. If the OCR2 is set equal to BOTTOM, the output will be continuously low and if set equal to MAX the output will be continuously high for non-inverted PWM mode. For inverted PWM the output will have the opposite logic values. At the very start of period 2 in Figure 59 OCn has a transition from high to low even though there is no Compare Match. The point of this transition is to guarantee symmetry around BOTTOM. There are two cases that give a transition without Compare Match. (cid:129) OCR2 changes its value from MAX, like in Figure 59. When the OCR2 value is MAX the OCn pin value is the same as the result of a down-counting Compare Match. To ensure symmetry around BOTTOM the OCn value at MAX must correspond to the result of an up-counting Compare Match. (cid:129) The timer starts counting from a value higher than the one in OCR2, and for that reason misses the Compare Match and hence the OCn change that would have happened on the way up. Timer/Counter Timing The following figures show the Timer/Counter in Synchronous mode, and the Timer Diagrams Clock (clk ) is therefore shown as a clock enable signal. In Asynchronous mode, clk T2 I/O should be replaced by the Timer/Counter Oscillator clock. The figures include informa- tion on when interrupt flags are set. Figure 60 contains timing data for basic Timer/Counter operation. The figure shows the count sequence close to the MAX value in all modes other than phase correct PWM mode. Figure 60. Timer/Counter Timing Diagram, no Prescaling clk I/O clk Tn (clk /1) I/O TCNTn MAX - 1 MAX BOTTOM BOTTOM + 1 TOVn Figure 61 shows the same timing data, but with the prescaler enabled. ATmega8535(L) 126 2502K–AVR–10/06
ATmega8535(L) Figure 61. Timer/Counter Timing Diagram, with Prescaler (f /8) clk_I/O clk I/O clk Tn (clk /8) I/O TCNTn MAX - 1 MAX BOTTOM BOTTOM + 1 TOVn Figure 62 shows the setting of OCF2 in all modes except CTC mode. Figure 62. Timer/Counter Timing Diagram, Setting of OCF2, with Prescaler (f /8) clk_I/O clk I/O clk Tn (clk /8) I/O TCNTn OCRn - 1 OCRn OCRn + 1 OCRn + 2 OCRn OCRn Value OCFn Figure 63 shows the setting of OCF2 and the clearing of TCNT2 in CTC mode. 127 2502K–AVR–10/06
Figure 63. Timer/Counter Timing Diagram, Clear Timer on Compare Match Mode, with Prescaler (f /8) clk_I/O clk I/O clk Tn (clk /8) I/O TCNTn TOP - 1 TOP BOTTOM BOTTOM + 1 (CTC) OCRn TOP OCFn 8-bit Timer/Counter Register Description Timer/Counter Control Register – TCCR2 Bit 7 6 5 4 3 2 1 0 FOC2 WGM20 COM21 COM20 WGM21 CS22 CS21 CS20 TCCR2 Read/Write W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 7 – FOC2: Force Output Compare The FOC2 bit is only active when the WGM bits specify a non-PWM mode. However, for ensuring compatibility with future devices, this bit must be set to zero when TCCR2 is written when operating in PWM mode. When writing a logical one to the FOC2 bit, an immediate Compare Match is forced on the Waveform Generation unit. The OC2 output is changed according to its COM21:0 bits setting. Note that the FOC2 bit is implemented as a strobe. Therefore it is the value present in the COM21:0 bits that determines the effect of the forced compare. A FOC2 strobe will not generate any interrupt, nor will it clear the timer in CTC mode using OCR2 as TOP. The FOC2 bit is always read as zero. (cid:129) Bit 6, 3 – WGM21:0: Waveform Generation Mode These bits control the counting sequence of the counter, the source for the maximum (TOP) counter value, and what type of waveform generation to be used. Modes of oper- ation supported by the Timer/Counter unit are: Normal mode, Clear Timer on Compare Match (CTC) mode, and two types of Pulse Width Modulation (PWM) modes. See Table 51 and “Modes of Operation” on page 122. ATmega8535(L) 128 2502K–AVR–10/06
ATmega8535(L) Table 51. Waveform Generation Mode Bit Description(1) WGM21 WGM20 Timer/Counter Mode Update of TOV2 Flag Mode (CTC2) (PWM2) of Operation TOP OCR2 Set on 0 0 0 Normal 0xFF Immediate MAX 1 0 1 PWM, Phase Correct 0xFF TOP BOTTOM 2 1 0 CTC OCR2 Immediate MAX 3 1 1 Fast PWM 0xFF BOTTOM MAX Note: 1. The CTC2 and PWM2 bit definition names are now obsolete. Use the WGM21:0 def- initions. However, the functionality and location of these bits are compatible with previous versions of the timer. (cid:129) Bit 5:4 – COM21:0: Compare Match Output Mode These bits control the Output Compare pin (OC2) behavior. If one or both of the COM21:0 bits are set, the OC2 output overrides the normal port functionality of the I/O pin it is connected to. However, note that the Data Direction Register (DDR) bit corre- sponding to OC2 pin must be set in order to enable the output driver. When OC2 is connected to the pin, the function of the COM21:0 bits depends on the WGM21:0 bit setting. Table 52 shows the COM21:0 bit functionality when the WGM21:0 bits are set to a Normal or CTC mode (non-PWM). Table 52. Compare Output Mode, non-PWM Mode COM21 COM20 Description 0 0 Normal port operation, OC2 disconnected. 0 1 Toggle OC2 on Compare Match. 1 0 Clear OC2 on Compare Match. 1 1 Set OC2 on Compare Match. Table 53 shows the COM21:0 bit functionality when the WGM21:0 bits are set to fast PWM mode. Table 53. Compare Output Mode, Fast PWM Mode(1) COM21 COM20 Description 0 0 Normal port operation, OC2 disconnected. 0 1 Reserved 1 0 Clear OC2 on Compare Match, set OC2 at TOP (Non-Inverting). 1 1 Set OC2 on Compare Match, clear OC2 at TOP (Inverting). Note: 1. A special case occurs when OCR2 equals TOP and COM21 is set. In this case, the Compare Match is ignored, but the set or clear is done at TOP. See “Fast PWM Mode” on page 123 for more details. 129 2502K–AVR–10/06
Table 54 shows the COM21:0 bit functionality when the WGM21:0 bits are set to phase correct PWM mode. Table 54. Compare Output Mode, Phase Correct PWM Mode(1) COM21 COM20 Description 0 0 Normal port operation, OC2 disconnected. 0 1 Reserved 1 0 Clear OC2 on Compare Match when up-counting. Set OC2 on Compare Match when down-counting. 1 1 Set OC2 on Compare Match when up-counting. Clear OC2 on Compare Match when down-counting. Note: 1. A special case occurs when OCR2 equals TOP and COM21 is set. In this case, the Compare Match is ignored, but the set or clear is done at TOP. See “Phase Correct PWM Mode” on page 125 for more details. (cid:129) Bit 2:0 – CS22:0: Clock Select The three clock select bits select the clock source to be used by the Timer/Counter, see Table 55. Table 55. Clock Select Bit Description CS22 CS21 CS20 Description 0 0 0 No clock source (Timer/Counter stopped). 0 0 1 clk /(No prescaling) T2S 0 1 0 clk /8 (From prescaler) T2S 0 1 1 clk /32 (From prescaler) T2S 1 0 0 clk /64 (From prescaler) T2S 1 0 1 clk /128 (From prescaler) T2S 1 1 0 clk /256 (From prescaler) T2S 1 1 1 clk /1024 (From prescaler) T2S Timer/Counter Register – TCNT2 Bit 7 6 5 4 3 2 1 0 TCNT2[7:0] TCNT2 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 The Timer/Counter Register gives direct access, both for read and write operations, to the Timer/Counter unit 8-bit counter. Writing to the TCNT2 Register blocks (removes) the Compare Match on the following timer clock. Modifying the counter (TCNT2) while the counter is running, introduces a risk of missing a Compare Match between TCNT2 and the OCR2 Register. ATmega8535(L) 130 2502K–AVR–10/06
ATmega8535(L) Output Compare Register – OCR2 Bit 7 6 5 4 3 2 1 0 OCR2[7:0] OCR2 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 The Output Compare Register contains an 8-bit value that is continuously compared with the counter value (TCNT2). A match can be used to generate an output compare interrupt, or to generate a waveform output on the OC2 pin. Asynchronous Operation of the Timer/Counter Asynchronous Status Register – ASSR Bit 7 6 5 4 3 2 1 0 – – – – AS2 TCN2UB OCR2UB TCR2UB ASSR Read/Write R R R R R/W R R R Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 3 – AS2: Asynchronous Timer/Counter2 When AS2 is written to zero, Timer/Counter2 is clocked from the I/O clock, clk . When I/O AS2 is written to one, Timer/Counter2 is clocked from a crystal Oscillator connected to the Timer Oscillator1 (TOSC1) pin. When the value of AS2 is changed, the contents of TCNT2, OCR2, and TCCR2 might be corrupted. (cid:129) Bit 2 – TCN2UB: Timer/Counter2 Update Busy When Timer/Counter2 operates asynchronously and TCNT2 is written, this bit becomes set. When TCNT2 has been updated from the temporary storage register, this bit is cleared by hardware. A logical zero in this bit indicates that TCNT2 is ready to be updated with a new value. (cid:129) Bit 1 – OCR2UB: Output Compare Register 2 Update Busy When Timer/Counter2 operates asynchronously and OCR2 is written, this bit becomes set. When OCR2 has been updated from the temporary storage register, this bit is cleared by hardware. A logical zero in this bit indicates that OCR2 is ready to be updated with a new value. (cid:129) Bit 0 – TCR2UB: Timer/Counter Control Register 2 Update Busy When Timer/Counter2 operates asynchronously and TCCR2 is written, this bit becomes set. When TCCR2 has been updated from the temporary storage register, this bit is cleared by hardware. A logical zero in this bit indicates that TCCR2 is ready to be updated with a new value. If a write is performed to any of the three Timer/Counter2 Registers while its update busy flag is set, the updated value might get corrupted and cause an unintentional inter- rupt to occur. The mechanisms for reading TCNT2, OCR2, and TCCR2 are different. When reading TCNT2, the actual timer value is read. When reading OCR2 or TCCR2, the value in the temporary storage register is read. 131 2502K–AVR–10/06
Asynchronous Operation of When Timer/Counter2 operates asynchronously, some considerations must be taken. Timer/Counter2 (cid:129) Warning: When switching between asynchronous and synchronous clocking of Timer/Counter2, the timer registers TCNT2, OCR2, and TCCR2 might be corrupted. A safe procedure for switching clock source is: 1. Disable the Timer/Counter2 interrupts by clearing OCIE2 and TOIE2. 2. Select clock source by setting AS2 as appropriate. 3. Write new values to TCNT2, OCR2, and TCCR2. 4. To switch to asynchronous operation: Wait for TCN2UB, OCR2UB, and TCR2UB. 5. Clear the Timer/Counter2 Interrupt Flags. 6. Enable interrupts, if needed. (cid:129) The Oscillator is optimized for use with a 32.768kHz watch crystal. Applying an external clock to the TOSC1 pin may result in incorrect Timer/Counter2 operation. The CPU main clock frequency must be more than four times the oscillator frequency. (cid:129) When writing to one of the registers TCNT2, OCR2, or TCCR2, the value is transferred to a temporary register, and latched after two positive edges on TOSC1. The user should not write a new value before the contents of the temporary register have been transferred to its destination. Each of the three mentioned registers have their individual temporary register, which means that, e.g., writing to TCNT2 does not disturb an OCR2 write in progress. To detect that a transfer to the destination register has taken place, the Asynchronous Status Register – ASSR – has been implemented. (cid:129) When entering Power-save or Extended Standby mode after having written to TCNT2, OCR2, or TCCR2, the user must wait until the written register has been updated if Timer/Counter2 is used to wake up the device. Otherwise, the MCU will enter sleep mode before the changes are effective. This is particularly important if the Output Compare 2 interrupt is used to wake up the device, since the output compare function is disabled during writing to OCR2 or TCNT2. If the write cycle is not finished, and the MCU enters sleep mode before the OCR2UB bit returns to zero, the device will never receive a Compare Match interrupt, and the MCU will not wake up. (cid:129) If Timer/Counter2 is used to wake the device up from Power-save or Extended Standby mode, precautions must be taken if the user wants to re-enter one of these modes: The interrupt logic needs one TOSC1 cycle to be reset. If the time between wake-up and re-entering sleep mode is less than one TOSC1 cycle, the interrupt will not occur, and the device will fail to wake up. If the user is in doubt whether the time before re-entering Power-save or Extended Standby mode is sufficient, the following algorithm can be used to ensure that one TOSC1 cycle has elapsed: 1. Write a value to TCCR2, TCNT2, or OCR2. 2. Wait until the corresponding Update Busy Flag in ASSR returns to zero. 3. Enter Power-save or Extended Standby mode. (cid:129) When the asynchronous operation is selected, the 32.768 kHz Oscillator for Timer/Counter2 is always running, except in Power-down and Standby modes. After a Power-up Reset or wake-up from Power-down or Standby mode, the user should be aware of the fact that this Oscillator might take as long as one second to stabilize. The user is advised to wait for at least one second before using Timer/Counter2 after Power-up or wake-up from Power-down or Standby mode. The contents of all Timer/Counter2 Registers must be considered lost after a wake-up from Power- ATmega8535(L) 132 2502K–AVR–10/06
ATmega8535(L) down or Standby mode due to unstable clock signal upon start-up, no matter whether the Oscillator is in use or a clock signal is applied to the TOSC1 pin. (cid:129) Description of wake-up from Power-save or Extended Standby mode when the timer is clocked asynchronously: When the interrupt condition is met, the wake up process is started on the following cycle of the timer clock, that is, the timer is always advanced by at least one before the processor can read the counter value. After wake-up, the MCU is halted for four cycles, it executes the interrupt routine, and resumes execution from the instruction following SLEEP. (cid:129) Reading of the TCNT2 Register shortly after wake-up from Power-save may give an incorrect result. Since TCNT2 is clocked on the asynchronous TOSC clock, reading TCNT2 must be done through a register synchronized to the internal I/O clock domain. Synchronization takes place for every rising TOSC1 edge. When waking up from Power-save mode, and the I/O clock (clk ) again becomes active, TCNT2 will I/O read as the previous value (before entering sleep) until the next rising TOSC1 edge. The phase of the TOSC clock after waking up from Power-save mode is essentially unpredictable, as it depends on the wake-up time. The recommended procedure for reading TCNT2 is thus as follows: 1. Write any value to either of the registers OCR2 or TCCR2. 2. Wait for the corresponding Update Busy Flag to be cleared. 3. Read TCNT2. (cid:129) During asynchronous operation, the synchronization of the interrupt flags for the asynchronous timer takes three processor cycles plus one timer cycle. The timer is therefore advanced by at least one before the processor can read the timer value causing the setting of the Interrupt Flag. The output compare pin is changed on the timer clock and is not synchronized to the processor clock. Timer/Counter Interrupt Mask Register – TIMSK Bit 7 6 5 4 3 2 1 0 OCIE2 TOIE2 TICIE1 OCIE1A OCIE1B TOIE1 OCIE0 TOIE0 TIMSK Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 7 – OCIE2: Timer/Counter2 Output Compare Match Interrupt Enable When the OCIE2 bit is written to one and the I-bit in the Status Register is set (one), the Timer/Counter2 Compare Match interrupt is enabled. The corresponding interrupt is executed if a Compare Match in Timer/Counter2 occurs (i.e., when the OCF2 bit is set in the Timer/Counter Interrupt Flag Register – TIFR). (cid:129) Bit 6 – TOIE2: Timer/Counter2 Overflow Interrupt Enable When the TOIE2 bit is written to one and the I-bit in the Status Register is set (one), the Timer/Counter2 Overflow interrupt is enabled. The corresponding interrupt is executed if an overflow in Timer/Counter2 occurs (i.e., when the TOV2 bit is set in the Timer/Counter Interrupt Flag Register – TIFR). 133 2502K–AVR–10/06
Timer/Counter Interrupt Flag Register – TIFR Bit 7 6 5 4 3 2 1 0 OCF2 TOV2 ICF1 OCF1A OCF1B TOV1 OCF0 TOV0 TIFR Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 7 – OCF2: Output Compare Flag 2 The OCF2 bit is set (one) when a Compare Match occurs between the Timer/Counter2 and the data in OCR2 – Output Compare Register 2. OCF2 is cleared by hardware when executing the corresponding interrupt handling vector. Alternatively, OCF2 is cleared by writing a logic one to the flag. When the I-bit in SREG, OCIE2 (Timer/Counter2 Compare Match interrupt enable), and OCF2 are set (one), the Timer/Counter2 Compare Match Interrupt is executed. (cid:129) Bit 6 – TOV2: Timer/Counter2 Overflow Flag The TOV2 bit is set (one) when an overflow occurs in Timer/Counter2. TOV2 is cleared by hardware when executing the corresponding interrupt handling vector. Alternatively, TOV2 is cleared by writing a logic one to the flag. When the SREG I-bit, TOIE2 (Timer/Counter2 Overflow Interrupt Enable), and TOV2 are set (one), the Timer/Counter2 Overflow interrupt is executed. In PWM mode, this bit is set when Timer/Counter2 changes counting direction at 0x00. Timer/Counter Prescaler Figure 64. Prescaler for Timer/Counter2 clkI/O clkT2S 10-BIT T/C PRESCALER Clear TOSC1 8 2 4 8 6 4 AS2 clk/T2S clk/3T2S clk/6T2S clk/12T2S clk/25T2S clk/102T2S PSR2 0 CS20 CS21 CS22 TIMER/COUNTER2 CLOCK SOURCE clk T2 The clock source for Timer/Counter2 is named clk . clk is, by default, connected to T2S T2S the main system I/O clock clk . By setting the AS2 bit in ASSR, Timer/Counter2 is asyn- IO chronously clocked from the TOSC1 pin. This enables use of Timer/Counter2 as a Real Time Counter (RTC). When AS2 is set, pins TOSC1 and TOSC2 are disconnected from Port C. A crystal can then be connected between the TOSC1 and TOSC2 pins to serve as an independent clock source for Timer/Counter2. The Oscillator is optimized for use with a 32.768 kHz crystal. Applying an external clock source to TOSC1 is not recommended. For Timer/Counter2, the possible prescaled selections are: clk /8, clk /32, clk /64, T2S T2S T2S clk /128, clk /256, and clk /1024. Additionally, clk as well as 0 (stop) may be T2S T2S T2S T2S selected. Setting the PSR2 bit in SFIOR resets the prescaler. This allows the user to operate with a predictable prescaler. ATmega8535(L) 134 2502K–AVR–10/06
ATmega8535(L) Special Function IO Register – SFIOR Bit 7 6 5 4 3 2 1 0 ADTS2 ADTS1 ADTS0 – ACME PUD PSR2 PSR10 SFIOR Read/Write R/W R/W R/W R R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 1 – PSR2: Prescaler Reset Timer/Counter2 When this bit is written to one, the Timer/Counter2 prescaler will be reset. The bit will be cleared by hardware after the operation is performed. Writing a zero to this bit will have no effect. This bit will always be read as zero if Timer/Counter2 is clocked by the internal CPU clock. If this bit is written when Timer/Counter2 is operating in asynchronous mode, the bit will remain one until the prescaler has been reset. 135 2502K–AVR–10/06
Serial Peripheral The Serial Peripheral Interface (SPI) allows high-speed synchronous data transfer Interface – SPI between the ATmega8535 and peripheral devices or between several AVR devices. The ATmega8535 SPI includes the following features: (cid:129) Full Duplex, Three-wire Synchronous Data Transfer (cid:129) Master or Slave Operation (cid:129) LSB First or MSB First Data Transfer (cid:129) Seven Programmable Bit Rates (cid:129) End of Transmission Interrupt Flag (cid:129) Write Collision Flag Protection (cid:129) Wake-up from Idle Mode (cid:129) Double Speed (CK/2) Master SPI Mode Figure 65. SPI Block Diagram(1) DIVIDER /2/4/8/16/32/64/128 X 2 PI S X 2 PI S Note: 1. Refer to Figure 1 on page 2, and Table 26 on page 60 for SPI pin placement. The interconnection between Master and Slave CPUs with SPI is shown in Figure 66. The system consists of two Shift Registers, and a Master clock generator. The SPI Mas- ter initiates the communication cycle when pulling low the Slave Select SS pin of the desired Slave. Master and Slave prepare the data to be sent in their respective Shift Registers, and the Master generates the required clock pulses on the SCK line to inter- change data. Data is always shifted from Master to Slave on the Master Out – Slave In, MOSI, line, and from Slave to Master on the Master In – Slave Out, MISO, line. After each data packet, the Master will synchronize the Slave by pulling high the Slave Select, SS, line. When configured as a Master, the SPI interface has no automatic control of the SS line. This must be handled by user software before communication can start. When this is ATmega8535(L) 136 2502K–AVR–10/06
ATmega8535(L) done, writing a byte to the SPI Data Register starts the SPI Clock Generator, and the hardware shifts the eight bits into the Slave. After shifting one byte, the SPI clock gener- ator stops, setting the end of Transmission Flag (SPIF). If the SPI Interrupt Enable bit (SPIE) in the SPCR Register is set, an interrupt is requested. The Master may continue to shift the next byte by writing it into SPDR, or signal the end of packet by pulling high the Slave Select, SS line. The last incoming byte will be kept in the buffer register for later use. When configured as a Slave, the SPI interface will remain sleeping with MISO tri-stated as long as the SS pin is driven high. In this state, software may update the contents of the SPI Data Register, SPDR, but the data will not be shifted out by incoming clock pulses on the SCK pin until the SS pin is driven low. As one byte has been completely shifted, the end of Transmission Flag, SPIF is set. If the SPI Interrupt Enable bit, SPIE, in the SPCR Register is set, an interrupt is requested. The Slave may continue to place new data to be sent into SPDR before reading the incoming data. The last incoming byte will be kept in the buffer register for later use. Figure 66. SPI Master-Slave Interconnection MSB MASTER LSB MSB SLAVE LSB MISO MISO 8 BIT SHIFT REGISTER 8 BIT SHIFT REGISTER MOSI MOSI SHIFT ENABLE SPI SCK SCK CLOCK GENERATOR SS SS V CC The system is single buffered in the transmit direction and double buffered in the receive direction. This means that bytes to be transmitted cannot be written to the SPI Data Register before the entire shift cycle is completed. When receiving data, however, a received character must be read from the SPI Data Register before the next character has been completely shifted in. Otherwise, the first byte is lost. In SPI Slave mode, the control logic will sample the incoming signal of the SCK pin. To ensure correct sampling of the clock signal, the minimum low and high periods should be: Low periods: Longer than 2 CPU clock cycles. High periods: Longer than 2 CPU clock cycles. When the SPI is enabled, the data direction of the MOSI, MISO, SCK, and SS pins is overridden according to Table 56 on page 138. For more details on automatic port over- rides, refer to “Alternate Port Functions” on page 57. 137 2502K–AVR–10/06
Table 56. SPI Pin Overrides(1) Pin Direction, Master SPI Direction, Slave SPI MOSI User Defined Input MISO Input User Defined SCK User Defined Input SS User Defined Input Note: 1. See “Alternate Functions Of Port B” on page 60 for a detailed description of how to define the direction of the user defined SPI pins. The following code examples show how to initialize the SPI as a Master and how to per- form a simple transmission. DDR_SPI in the examples must be replaced by the actual Data Direction Register controlling the SPI pins. DD_MOSI, DD_MISO and DD_SCK must be replaced by the actual data direction bits for these pins. For example, if MOSI is placed on pin PB5, replace DD_MOSI with DDB5, and DDR_SPI with DDRB. Assembly Code Example(1) ATmega8535(L) 138 2502K–AVR–10/06
ATmega8535(L) SPI_MasterInit: ; Set MOSI and SCK output, all others input ldi r17,(1<<DD_MOSI)|(1<<DD_SCK) out DDR_SPI,r17 ; Enable SPI, Master, set clock rate fck/16 ldi r17,(1<<SPE)|(1<<MSTR)|(1<<SPR0) out SPCR,r17 ret SPI_MasterTransmit: ; Start transmission of data (r16) out SPDR,r16 Wait_Transmit: ; Wait for transmission complete sbis SPSR,SPIF rjmp Wait_Transmit ret C Code Example(1) void SPI_MasterInit(void) { /* Set MOSI and SCK output, all others input */ DDR_SPI = (1<<DD_MOSI)|(1<<DD_SCK); /* Enable SPI, Master, set clock rate fck/16 */ SPCR = (1<<SPE)|(1<<MSTR)|(1<<SPR0); } void SPI_MasterTransmit(char cData) { /* Start transmission */ SPDR = cData; /* Wait for transmission complete */ while(!(SPSR & (1<<SPIF))) ; } Note: 1. See “About Code Examples” on page 7. 139 2502K–AVR–10/06
The following code examples show how to initialize the SPI as a Slave and how to per- form a simple reception. Assembly Code Example(1) SPI_SlaveInit: ; Set MISO output, all others input ldi r17,(1<<DD_MISO) out DDR_SPI,r17 ; Enable SPI ldi r17,(1<<SPE) out SPCR,r17 ret SPI_SlaveReceive: ; Wait for reception complete sbis SPSR,SPIF rjmp SPI_SlaveReceive ; Read received data and return in r16,SPDR ret C Code Example(1) void SPI_SlaveInit(void) { /* Set MISO output, all others input */ DDR_SPI = (1<<DD_MISO); /* Enable SPI */ SPCR = (1<<SPE); } char SPI_SlaveReceive(void) { /* Wait for reception complete */ while(!(SPSR & (1<<SPIF))) ; /* Return Data Register */ return SPDR; } Note: 1. See “About Code Examples” on page 7. ATmega8535(L) 140 2502K–AVR–10/06
ATmega8535(L) SS Pin Functionality Slave Mode When the SPI is configured as a Slave, the Slave Select (SS) pin is always input. When SS is held low, the SPI is activated, and MISO becomes an output if configured so by the user. All other pins are inputs. When SS is driven high, all pins are inputs, and the SPI is passive, which means that it will not receive incoming data. Note that the SPI logic will be reset once the SS pin is driven high. The SS pin is useful for packet/byte synchronization to keep the Slave bit counter syn- chronous with the Master clock generator. When the SS pin is driven high, the SPI Slave will immediately reset the send and receive logic, and drop any partially received data in the Shift Register. Master Mode When the SPI is configured as a Master (MSTR in SPCR is set), the user can determine the direction of the SS pin. If SS is configured as an output, the pin is a general output pin which does not affect the SPI system. Typically, the pin will be driving the SS pin of the SPI Slave. If SS is configured as an input, it must be held high to ensure Master SPI operation. If the SS pin is driven low by peripheral circuitry when the SPI is configured as a Master with the SS pin defined as an input, the SPI system interprets this as another Master selecting the SPI as a Slave and starting to send data to it. To avoid bus contention, the SPI system takes the following actions: 1. The MSTR bit in SPCR is cleared and the SPI system becomes a Slave. As a result of the SPI becoming a Slave, the MOSI and SCK pins become inputs. 2. The SPIF Flag in SPSR is set, and if the SPI interrupt is enabled, and the I-bit in SREG is set, the interrupt routine will be executed. Thus, when interrupt-driven SPI transmission is used in Master mode, and there exists a possibility that SS is driven low, the interrupt should always check that the MSTR bit is still set. If the MSTR bit has been cleared by a Slave Select, it must be set by the user to re-enable SPI Master mode. SPI Control Register – SPCR Bit 7 6 5 4 3 2 1 0 SPIE SPE DORD MSTR CPOL CPHA SPR1 SPR0 SPCR Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 7 – SPIE: SPI Interrupt Enable This bit causes the SPI interrupt to be executed if SPIF bit in the SPSR Register is set and the if the Global Interrupt Enable bit in SREG is set. (cid:129) Bit 6 – SPE: SPI Enable When the SPE bit is written to one, the SPI is enabled. This bit must be set to enable any SPI operations. (cid:129) Bit 5 – DORD: Data Order When the DORD bit is written to one, the LSB of the data word is transmitted first. When the DORD bit is written to zero, the MSB of the data word is transmitted first. (cid:129) Bit 4 – MSTR: Master/Slave Select This bit selects Master SPI mode when written to one, and Slave SPI mode when written logic zero. If SS is configured as an input and is driven low while MSTR is set, MSTR will 141 2502K–AVR–10/06
be cleared, and SPIF in SPSR will become set. The user will then have to set MSTR to re-enable SPI Master mode. (cid:129) Bit 3 – CPOL: Clock Polarity When this bit is written to one, SCK is high when idle. When CPOL is written to zero, SCK is low when idle. Refer to Figure 67 and Figure 68 for an example. The CPOL func- tionality is summarized below: Table 57. CPOL Functionality CPOL Leading Edge Trailing Edge 0 Rising Falling 1 Falling Rising (cid:129) Bit 2 – CPHA: Clock Phase The settings of the Clock Phase bit (CPHA) determine if data is sampled on the leading (first) or trailing (last) edge of SCK. Refer to Figure 67 and Figure 68 for an example. The CPOL functionality is summarized below: Table 58. CPHA Functionality CPHA Leading Edge Trailing Edge 0 Sample Setup 1 Setup Sample (cid:129) Bits 1, 0 – SPR1, SPR0: SPI Clock Rate Select 1 and 0 These two bits control the SCK rate of the device configured as a Master. SPR1 and SPR0 have no effect on the Slave. The relationship between SCK and the Oscillator Clock frequency f is shown in the following table: osc Table 59. Relationship between SCK and the Oscillator Frequency SPI2X SPR1 SPR0 SCK Frequency 0 0 0 f /4 osc 0 0 1 f /16 osc 0 1 0 f /64 osc 0 1 1 f /128 osc 1 0 0 f /2 osc 1 0 1 f /8 osc 1 1 0 f /32 osc 1 1 1 f /64 osc ATmega8535(L) 142 2502K–AVR–10/06
ATmega8535(L) SPI Status Register – SPSR Bit 7 6 5 4 3 2 1 0 SPIF WCOL – – – – – SPI2X SPSR Read/Write R R R R R R R R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 7 – SPIF: SPI Interrupt Flag When a serial transfer is complete, the SPIF Flag is set. An interrupt is generated if SPIE in SPCR is set and global interrupts are enabled. If SS is an input and is driven low when the SPI is in Master mode, this will also set the SPIF Flag. SPIF is cleared by hardware when executing the corresponding interrupt handling vector. Alternatively, the SPIF bit is cleared by first reading the SPI Status Register with SPIF set, then accessing the SPI Data Register (SPDR). (cid:129) Bit 6 – WCOL: Write COLlision flag The WCOL bit is set if the SPI Data Register (SPDR) is written during a data transfer. The WCOL bit (and the SPIF bit) are cleared by first reading the SPI Status Register with WCOL set, and then accessing the SPI Data Register. (cid:129) Bit 5..1 – Res: Reserved Bits These bits are reserved bits in the ATmega8535 and will always read as zero. (cid:129) Bit 0 – SPI2X: Double SPI Speed Bit When this bit is written logic one the SPI speed (SCK Frequency) will be doubled when the SPI is in Master mode (see Table 59). This means that the minimum SCK period will be two CPU clock periods. When the SPI is configured as Slave, the SPI is only guaran- teed to work at f /4 or lower. osc The SPI interface on the ATmega8535 is also used for program memory and EEPROM downloading or uploading. See page 251 for Serial Programming and verification. SPI Data Register – SPDR Bit 7 6 5 4 3 2 1 0 MSB LSB SPDR Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value X X X X X X X X Undefined The SPI Data Register is a read/write register used for data transfer between the Regis- ter File and the SPI Shift Register. Writing to the register initiates data transmission. Reading the register causes the Shift Register receive buffer to be read. 143 2502K–AVR–10/06
Data Modes There are four combinations of SCK phase and polarity with respect to serial data, which are determined by control bits CPHA and CPOL. The SPI data transfer formats are shown in Figure 67 and Figure 68. Data bits are shifted out and latched in on oppo- site edges of the SCK signal, ensuring sufficient time for data signals to stabilize. This is clearly seen by summarizing Table 57 and Table 58, as done below: Table 60. CPOL Functionality Leading Edge Trailing Edge SPI Mode CPOL=0, CPHA=0 Sample (Rising) Setup (Falling) 0 CPOL=0, CPHA=1 Setup (Rising) Sample (Falling) 1 CPOL=1, CPHA=0 Sample (Falling) Setup (Rising) 2 CPOL=1, CPHA=1 Setup (Falling) Sample (Rising) 3 Figure 67. SPI Transfer Format with CPHA = 0 SCK (CPOL = 0) mode 0 SCK (CPOL = 1) mode 2 SAMPLE I MOSI/MISO CHANGE 0 MOSI PIN CHANGE 0 MISO PIN SS MSB first (DORD = 0) MSB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 LSB LSB first (DORD = 1) LSB Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 MSB Figure 68. SPI Transfer Format with CPHA = 1 SCK (CPOL = 0) mode 1 SCK (CPOL = 1) mode 3 SAMPLE I MOSI/MISO CHANGE 0 MOSI PIN CHANGE 0 MISO PIN SS MSB first (DORD = 0) MSB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 LSB LSB first (DORD = 1) LSB Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 MSB ATmega8535(L) 144 2502K–AVR–10/06
ATmega8535(L) USART The Universal Synchronous and Asynchronous serial Receiver and Transmitter (USART) is a highly flexible serial communication device. The main features are: (cid:129) Full Duplex Operation (Independent Serial Receive and Transmit Registers) (cid:129) Asynchronous or Synchronous Operation (cid:129) Master or Slave Clocked Synchronous Operation (cid:129) High Resolution Baud Rate Generator (cid:129) Supports Serial Frames with 5, 6, 7, 8, or 9 Data Bits and 1 or 2 Stop Bits (cid:129) Odd or Even Parity Generation and Parity Check Supported by Hardware (cid:129) Data OverRun Detection (cid:129) Framing Error Detection (cid:129) Noise Filtering Includes False Start Bit Detection and Digital Low Pass Filter (cid:129) Three Separate Interrupts on TX Complete, TX Data Register Empty and RX Complete (cid:129) Multi-processor Communication Mode (cid:129) Double Speed Asynchronous Communication Mode Overview A simplified block diagram of the USART Transmitter is shown in Figure 69. CPU acces- sible I/O Registers and I/O pins are shown in bold. Figure 69. USART Block Diagram(1) Clock Generator UBRR[H:L] OSC BAUD RATE GENERATOR SYNC LOGIC PIN XCK CONTROL Transmitter TX UDR (Transmit) CONTROL PARITY S GENERATOR U PIN B TRANSMIT SHIFT REGISTER CONTROL TxD A T A D Receiver CLOCK RX RECOVERY CONTROL DATA PIN RECEIVE SHIFT REGISTER RxD RECOVERY CONTROL PARITY UDR (Receive) CHECKER UCSRA UCSRB UCSRC Note: 1. Refer to Figure 1 on page 2, Table 34 on page 66, and Table 28 on page 62 for USART pin placement. 145 2502K–AVR–10/06
The dashed boxes in the block diagram separate the three main parts of the USART (listed from the top): Clock Generator, Transmitter and Receiver. Control registers are shared by all units. The clock generation logic consists of synchronization logic for exter- nal clock input used by synchronous slave operation, and the baud rate generator. The XCK (Transfer Clock) pin is only used by Synchronous Transfer mode. The Transmitter consists of a single write buffer, a serial Shift Register, Parity Generator and control logic for handling different serial frame formats. The write buffer allows a continuous transfer of data without any delay between frames. The Receiver is the most complex part of the USART module due to its clock and data recovery units. The recovery units are used for asynchronous data reception. In addition to the recovery units, the Receiver includes a Parity Checker, control logic, a Shift Register and a two level receive buffer (UDR). The Receiver supports the same frame formats as the Transmitter, and can detect frame error, data overrun and parity errors. AVR USART vs. AVR UART – The USART is fully compatible with the AVR UART regarding: Compatibility (cid:129) Bit locations inside all USART Registers (cid:129) Baud Rate Generation (cid:129) Transmitter Operation (cid:129) Transmit Buffer Functionality (cid:129) Receiver Operation However, the receive buffering has two improvements that will affect the compatibility in some special cases: (cid:129) A second buffer register has been added. The two buffer registers operate as a circular FIFO buffer. Therefore the UDR must only be read once for each incoming data! More important is the fact that the Error Flags (FE and DOR) and the ninth data bit (RXB8) are buffered with the data in the receive buffer. Therefore the status bits must always be read before the UDR Register is read. Otherwise the error status will be lost since the buffer state is lost. (cid:129) The Receiver Shift Register can now act as a third buffer level. This is done by allowing the received data to remain in the serial Shift Register (see Figure 69) if the buffer registers are full, until a new start bit is detected. The USART is therefore more resistant to Data OverRun (DOR) error conditions. The following control bits have changed name, but have same functionality and register location: (cid:129) CHR9 is changed to UCSZ2 (cid:129) OR is changed to DOR Clock Generation The clock generation logic generates the base clock for the Transmitter and Receiver. The USART supports four modes of clock operation: Normal asynchronous, Double Speed asynchronous, Master synchronous and Slave synchronous mode. The UMSEL bit in USART Control and Status Register C (UCSRC) selects between asynchronous and synchronous operation. Double Speed (asynchronous mode only) is controlled by the U2X found in the UCSRA Register. When using Synchronous mode (UMSEL = 1), the Data Direction Register for the XCK pin (DDR_XCK) controls whether the clock source is internal (Master mode) or external (Slave mode). The XCK pin is only active when using synchronous mode. Figure 70 shows a block diagram of the clock generation logic. ATmega8535(L) 146 2502K–AVR–10/06
ATmega8535(L) Figure 70. Clock Generation Logic, Block Diagram UBRR U2X fosc Prescaling UBRR+1 / 2 / 4 / 2 Down-Counter 0 1 0 OSC txclk 1 DDR_XCK Sync Edge xcki Register Detector 0 XCK UMSEL xcko 1 Pin DDR_XCK UCPOL 1 rxclk 0 Signal description: txclk Transmitter clock (Internal Signal). rxclk Receiver base clock (Internal Signal). xcki Input from XCK pin (internal Signal). Used for synchronous slave operation. xcko Clock output to XCK pin (Internal Signal). Used for synchronous master operation. fosc XTAL pin frequency (System Clock). Internal Clock Generation – Internal clock generation is used for the asynchronous and the synchronous master The Baud Rate Generator modes of operation. The description in this section refers to Figure 70. The USART Baud Rate Register (UBRR) and the down-counter connected to it function as a programmable prescaler or baud rate generator. The down-counter, running at sys- tem clock (fosc), is loaded with the UBRR value each time the counter has counted down to zero or when the UBRRL Register is written. A clock is generated each time the counter reaches zero. This clock is the baud rate generator clock output (=fosc/(UBRR+1)). The Transmitter divides the baud rate generator clock output by 2, 8, or 16 depending on mode. The baud rate generator output is used directly by the receiver’s clock and data recovery units. However, the recovery units use a state machine that uses 2, 8, or 16 states depending on mode set by the state of the UMSEL, U2X and DDR_XCK bits. Table 61 contains equations for calculating the baud rate (in bits per second) and for calculating the UBRR value for each mode of operation using an internally generated clock source. 147 2502K–AVR–10/06
Table 61. Equations for Calculating Baud Rate Register Setting Equation for Calculating Equation for Calculating Operating Mode Baud Rate(1) UBRR Value Asynchronous Normal Mode f f (U2X = 0) BAUD = ----------------O----S---C---------------- UBRR = ---------O---S---C---------–1 16(UBRR+1) 16BAUD Asynchronous Double Speed f f Mode (U2X = 1) BAUD = --------------O----S---C-------------- UBRR = -------O----S--C-------–1 8(UBRR+1) 8BAUD Synchronous Master Mode f f BAUD = --------------O----S---C-------------- UBRR = -------O----S--C-------–1 2(UBRR+1) 2BAUD Note: 1. The baud rate is defined to be the transfer rate in bit per second (bps). BAUD Baud rate (in bits per second, bps) f System Oscillator clock frequency OSC UBRR Contents of the UBRRH and UBRRL Registers, (0 - 4095) Some examples of UBRR values for some system clock frequencies are found in Table 69 (see page 170). Double Speed Operation The transfer rate can be doubled by setting the U2X bit in UCSRA. Setting this bit only (U2X) has effect for the asynchronous operation. Set this bit to zero when using synchronous operation. Setting this bit will reduce the divisor of the baud rate divider from 16 to 8, effectively doubling the transfer rate for asynchronous communication. Note however that the Receiver will in this case only use half the number of samples (reduced from 16 to 8) for data sampling and clock recovery, and therefore a more accurate baud rate setting and system clock are required when this mode is used. For the Transmitter, there are no downsides. External Clock External clocking is used by the synchronous slave modes of operation. The description in this section refers to Figure 70 for details. External clock input from the XCK pin is sampled by a synchronization register to mini- mize the chance of meta-stability. The output from the synchronization register must then pass through an edge detector before it can be used by the Transmitter and Receiver. This process introduces a two CPU clock period delay and therefore the max- imum external XCK clock frequency is limited by the following equation: f OSC f <----------- XCK 4 Note that f depends on the stability of the system clock source. It is therefore recom- osc mended to add some margin to avoid possible loss of data due to frequency variations. ATmega8535(L) 148 2502K–AVR–10/06
ATmega8535(L) Synchronous Clock Operation When Synchronous mode is used (UMSEL = 1), the XCK pin will be used as either clock input (Slave) or clock output (Master). The dependency between the clock edges and data sampling or data change is the same. The basic principle is that data input (on RxD) is sampled at the opposite XCK clock edge of the edge the data output (TxD) is changed. Figure 71. Synchronous Mode XCK Timing UCPOL = 1 XCK RxD / TxD Sample UCPOL = 0 XCK RxD / TxD Sample The UCPOL bit UCRSC selects which XCK clock edge is used for data sampling and which is used for data change. As Figure 71 shows, when UCPOL is zero the data will be changed at rising XCK edge and sampled at falling XCK edge. If UCPOL is set, the data will be changed at falling XCK edge and sampled at rising XCK edge. Frame Formats A serial frame is defined to be one character of data bits with synchronization bits (start and stop bits), and optionally a parity bit for error checking. The USART accepts all 30 combinations of the following as valid frame formats: (cid:129) 1 start bit (cid:129) 5, 6, 7, 8, or 9 data bits (cid:129) no even or odd parity bit (cid:129) 1 or 2 stop bits A frame starts with the start bit followed by the least significant data bit. Then the next data bits, up to a total of nine, are succeeding, ending with the most significant bit. If enabled, the parity bit is inserted after the data bits, before the stop bits. When a com- plete frame is transmitted, it can be directly followed by a new frame, or the communication line can be set to an idle (high) state. Figure 72 illustrates the possible combinations of the frame formats. Bits inside brackets are optional. Figure 72. Frame Formats FRAME (IDLE) St 0 1 2 3 4 [5] [6] [7] [8] [P] Sp1 [Sp2] (St / IDLE) St Start bit, always low. (n) Data bits (0 to 8). P Parity bit. Can be odd or even. 149 2502K–AVR–10/06
Sp Stop bit, always high. IDLE No transfers on the communication line (RxD or TxD). An IDLE line must be high. The frame format used by the USART is set by the UCSZ2:0, UPM1:0 and USBS bits in UCSRB and UCSRC. The Receiver and Transmitter use the same setting. Note that changing the setting of any of these bits will corrupt all ongoing communication for both the Receiver and Transmitter. The USART Character SiZe (UCSZ2:0) bits select the number of data bits in the frame. The USART Parity mode (UPM1:0) bits enable and set the type of parity bit. The selec- tion between one or two stop bits is done by the USART Stop Bit Select (USBS) bit. The Receiver ignores the second stop bit. An FE (Frame Error) will therefore only be detected in the cases where the first stop bit is zero. Parity Bit Calculation The parity bit is calculated by doing an exclusive-or of all the data bits. If odd parity is used, the result of the exclusive or is inverted. The relation between the parity bit and data bits is as follows:: P = d ⊕…⊕d ⊕d ⊕d ⊕d ⊕0 even n–1 3 2 1 0 P = d ⊕…⊕d ⊕d ⊕d ⊕d ⊕1 odd n–1 3 2 1 0 P Parity bit using even parity even P Parity bit using odd parity odd d Data bit n of the character n If used, the parity bit is located between the last data bit and first stop bit of a serial frame. USART Initialization The USART has to be initialized before any communication can take place. The initial- ization process normally consists of setting the baud rate, setting frame format and enabling the Transmitter or the Receiver depending on the usage. For interrupt driven USART operation, the Global Interrupt Flag should be cleared (and interrupts globally disabled) when doing the initialization. Before doing a re-initialization with a changed baud rate or frame format, be sure that there are no ongoing transmissions during the period the registers are changed. The TXC Flag can be used to check that the Transmitter has completed all transfers and the RXC Flag can be used to check that there are no unread data in the receive buffer. Note that the TXC Flag must be cleared before each transmission (before UDR is written) if it is used for this purpose. ATmega8535(L) 150 2502K–AVR–10/06
ATmega8535(L) The following simple USART initialization code examples show one assembly and one C function that are equal in functionality. The examples assume asynchronous opera- tion using polling (no interrupts enabled) and a fixed frame format. The baud rate is given as a function parameter. For the assembly code, the baud rate parameter is assumed to be stored in the r17:r16 registers. When the function writes to the UCSRC Register, the URSEL bit (MSB) must be set due to the sharing of I/O location by UBRRH and UCSRC. Assembly Code Example(1) USART_Init: ; Set baud rate out UBRRH, r17 out UBRRL, r16 ; Enable Receiver and Transmitter ldi r16, (1<<RXEN)|(1<<TXEN) out UCSRB,r16 ; Set frame format: 8data, 2stop bit ldi r16, (1<<URSEL)|(1<<USBS)|(3<<UCSZ0) out UCSRC,r16 ret C Code Example(1) #define FOSC 1843200// Clock Speed #define BAUD 9600 #define MYUBRR FOSC/16/BAUD-1 void main( void ) { ... USART_INIT ( MYUBRR ); ... } void USART_Init( unsigned int baud ) { /* Set baud rate */ UBRRH = (unsigned char)(baud>>8); UBRRL = (unsigned char)baud; /* Enable receiver and transmitter */ UCSRB = (1<<RXEN)|(1<<TXEN); /* Set frame format: 8data, 2stop bit */ UCSRC = (1<<USBS)|(3<<UCSZ0); } Note: 1. See “About Code Examples” on page 7. More advanced initialization routines can be made that include frame format as parame- ters, disable interrupts and so on. However, many applications use a fixed setting of the baud and control registers, and for these types of applications the initialization code can be placed directly in the main routine or be combined with initialization code for other I/O modules. 151 2502K–AVR–10/06
Data Transmission – The The USART Transmitter is enabled by setting the Transmit Enable (TXEN) bit in the USART Transmitter UCSRB Register. When the Transmitter is enabled, the normal port operation of the TxD pin is overridden by the USART and given the function as the Transmitter’s serial output. The baud rate, mode of operation and frame format must be set up once before doing any transmissions. If synchronous operation is used, the clock on the XCK pin will be overridden and used as transmission clock. Sending Frames with 5 to 8 A data transmission is initiated by loading the transmit buffer with the data to be trans- Data Bits mitted. The CPU can load the transmit buffer by writing to the UDR I/O location. The buffered data in the transmit buffer will be moved to the Shift Register when the Shift Register is ready to send a new frame. The Shift Register is loaded with new data if it is in idle state (no ongoing transmission) or immediately after the last stop bit of the previ- ous frame is transmitted. When the Shift Register is loaded with new data, it will transfer one complete frame at the rate given by the baud register, U2X bit or by XCK depending on mode of operation. The following code examples show a simple USART transmit function based on polling of the Data Register Empty (UDRE) Flag. When using frames with less than eight bits, the most significant bits written to the UDR are ignored. The USART has to be initialized before the function can be used. For the assembly code, the data to be sent is assumed to be stored in register R16. Assembly Code Example(1) USART_Transmit: ; Wait for empty transmit buffer sbis UCSRA,UDRE rjmp USART_Transmit ; Put data (r16) into buffer, sends the data out UDR,r16 ret C Code Example(1) void USART_Transmit( unsigned char data ) { /* Wait for empty transmit buffer */ while ( !( UCSRA & (1<<UDRE)) ) ; /* Put data into buffer, sends the data */ UDR = data; } Note: 1. See “About Code Examples” on page 7. The function simply waits for the transmit buffer to be empty by checking the UDRE Flag, before loading it with new data to be transmitted. If the Data Register Empty inter- rupt is utilized, the interrupt routine writes the data into the buffer. ATmega8535(L) 152 2502K–AVR–10/06
ATmega8535(L) Sending Frames with 9 Data If 9-bit characters are used (UCSZ = 7), the ninth bit must be written to the TXB8 bit in Bits UCSRB before the low byte of the character is written to UDR. The following code examples show a transmit function that handles 9-bit characters. For the assembly code, the data to be sent is assumed to be stored in registers R17:R16. Assembly Code Example(1) USART_Transmit: ; Wait for empty transmit buffer sbis UCSRA,UDRE rjmp USART_Transmit ; Copy 9th bit from r17 to TXB8 cbi UCSRB,TXB8 sbrc r17,0 sbi UCSRB,TXB8 ; Put LSB data (r16) into buffer, sends the data out UDR,r16 ret C Code Example(1) void USART_Transmit( unsigned int data ) { /* Wait for empty transmit buffer */ while ( !( UCSRA & (1<<UDRE))) ) ; /* Copy 9th bit to TXB8 */ UCSRB &= ~(1<<TXB8); if ( data & 0x0100 ) UCSRB |= (1<<TXB8); /* Put data into buffer, sends the data */ UDR = data; } Note: 1. These transmit functions are written to be general functions. They can be optimized if the contents of the UCSRB is static. (For example, only the TXB8 bit of the UCSRB Register is used after initialization.) The ninth bit can be used for indicating an address frame when using multi processor communication mode or for other protocol handling as for example synchronization. Transmitter Flags and The USART Transmitter has two flags that indicate its state: USART Data Register Interrupts Empty (UDRE) and Transmit Complete (TXC). Both flags can be used for generating interrupts. The Data Register Empty (UDRE) Flag indicates whether the transmit buffer is ready to receive new data. This bit is set when the transmit buffer is empty, and cleared when the transmit buffer contains data to be transmitted that has not yet been moved into the Shift Register. For compatibility with future devices, always write this bit to zero when writing the UCSRA Register. When the Data Register Empty Interrupt Enable (UDRIE) bit in UCSRB is written to one, the USART Data Register Empty interrupt will be executed as long as UDRE is set (pro- vided that global interrupts are enabled). UDRE is cleared by writing UDR. When 153 2502K–AVR–10/06
interrupt-driven data transmission is used, the Data Register Empty interrupt routine must either write new data to UDR in order to clear UDRE or disable the Data Register Empty interrupt, otherwise a new interrupt will occur once the interrupt routine terminates. The Transmit Complete (TXC) Flag bit is set to one when the entire frame in the transmit Shift Register has been shifted out and there are no new data currently present in the transmit buffer. The TXC Flag bit is automatically cleared when a transmit complete interrupt is executed, or it can be cleared by writing a one to its bit location. The TXC Flag is useful in half-duplex communication interfaces (like the RS-485 standard), where a transmitting application must enter receive mode and free the communication bus immediately after completing the transmission. When the Transmit Compete Interrupt Enable (TXCIE) bit in UCSRB is set, the USART Transmit Complete Interrupt will be executed when the TXC Flag becomes set (pro- vided that global interrupts are enabled). When the transmit complete interrupt is used, the interrupt handling routine does not have to clear the TXC Flag, this is done automat- ically when the interrupt is executed. Parity Generator The parity generator calculates the parity bit for the serial frame data. When parity bit is enabled (UPM1 = 1), the Transmitter Control Logic inserts the parity bit between the last data bit and the first stop bit of the frame that is sent. Disabling the Transmitter The disabling of the Transmitter (setting the TXEN to zero) will not become effective until ongoing and pending transmissions are completed (i.e., when the transmit Shift Register and Transmit Buffer Register do not contain data to be transmitted). When dis- abled, the Transmitter will no longer override the TxD pin. ATmega8535(L) 154 2502K–AVR–10/06
ATmega8535(L) Data Reception – The The USART Receiver is enabled by writing the Receive Enable (RXEN) bit in the USART Receiver UCSRB Register to one. When the Receiver is enabled, the normal pin operation of the RxD pin is overridden by the USART and given the function as the Receiver’s serial input. The baud rate, mode of operation and frame format must be set up once before any serial reception can be done. If synchronous operation is used, the clock on the XCK pin will be used as a transfer clock. Receiving Frames with 5 to 8 The Receiver starts data reception when it detects a valid start bit. Each bit that follows Data Bits the start bit will be sampled at the baud rate or XCK clock, and shifted into the Receive Shift Register until the first stop bit of a frame is received. A second stop bit will be ignored by the Receiver. When the first stop bit is received, (i.e., a complete serial frame is present in the receive Shift Register, the contents of the Shift Register will be moved into the receive buffer. The receive buffer can then be read by reading the UDR I/O location. The following code example shows a simple USART receive function based on polling of the Receive Complete (RXC) Flag. When using frames with less than eight bits the most significant bits of the data read from the UDR will be masked to zero. The USART has to be initialized before the function can be used. Assembly Code Example(1) USART_Receive: ; Wait for data to be received sbis UCSRA, RXC rjmp USART_Receive ; Get and return received data from buffer in r16, UDR ret C Code Example(1) unsigned char USART_Receive( void ) { /* Wait for data to be received */ while ( !(UCSRA & (1<<RXC)) ) ; /* Get and return received data from buffer */ return UDR; } Note: 1. See “About Code Examples” on page 7. The function simply waits for data to be present in the receive buffer by checking the RXC Flag, before reading the buffer and returning the value. 155 2502K–AVR–10/06
Receiving Frames with 9 Data If 9-bit characters are used (UCSZ=7) the ninth bit must be read from the RXB8 bit in Bits UCSRB before reading the low bits from the UDR. This rule applies to the FE, DOR, and PE Status Flags as well. Read status from UCSRA, then data from UDR. Reading the UDR I/O location will change the state of the receive buffer FIFO and consequently the TXB8, FE, DOR, and PE bits, which all are stored in the FIFO, will change. The following code example shows a simple USART receive function that handles both 9-bit characters and the status bits. Assembly Code Example(1) USART_Receive: ; Wait for data to be received sbis UCSRA, RXC rjmp USART_Receive ; Get status and 9th bit, then data from buffer in r18, UCSRA in r17, UCSRB in r16, UDR ; If error, return -1 andi r18,(1<<FE)|(1<<DOR)|(1<<PE) breq USART_ReceiveNoError ldi r17, HIGH(-1) ldi r16, LOW(-1) USART_ReceiveNoError: ; Filter the 9th bit, then return lsr r17 andi r17, 0x01 ret C Code Example(1) unsigned int USART_Receive( void ) { unsigned char status, resh, resl; /* Wait for data to be received */ while ( !(UCSRA & (1<<RXC)) ) ; /* Get status and 9th bit, then data */ /* from buffer */ status = UCSRA; resh = UCSRB; resl = UDR; /* If error, return -1 */ if ( status & (1<<FE)|(1<<DOR)|(1<<PE) ) return -1; /* Filter the 9th bit, then return */ resh = (resh >> 1) & 0x01; return ((resh << 8) | resl); } ATmega8535(L) 156 2502K–AVR–10/06
ATmega8535(L) Note: 1. See “About Code Examples” on page 7. The receive function example reads all the I/O Registers into the Register File before any computation is done. This gives an optimal receive buffer utilization since the buffer location read will be free to accept new data as early as possible. Receive Compete Flag and The USART Receiver has one flag that indicates the receiver state. Interrupt The Receive Complete (RXC) Flag indicates if there are unread data present in the receive buffer. This flag is one when unread data exist in the receive buffer and zero when the receive buffer is empty (i.e., does not contain any unread data). If the Receiver is disabled (RXEN = 0), the receive buffer will be flushed and consequently the RXC bit will become zero. When the Receive Complete Interrupt Enable (RXCIE) in UCSRB is set, the USART Receive Complete Interrupt will be executed as long as the RXC Flag is set (provided that global interrupts are enabled). When interrupt-driven data reception is used, the receive complete routine must read the received data from UDR in order to clear the RXC Flag, otherwise a new interrupt will occur once the interrupt routine terminates. Receiver Error Flags The USART Receiver has three Error Flags: Frame Error (FE), Data OverRun (DOR) and Parity Error (PE). All can be accessed by reading UCSRA. Common for the error flags is that they are located in the receive buffer together with the frame for which they indicate the error status. Due to the buffering of the error flags, the UCSRA must be read before the receive buffer (UDR), since reading the UDR I/O location changes the buffer read location. Another equality for the error flags is that they can not be altered by software doing a write to the flag location. However, all flags must be set to zero when the UCSRA is written for upward compatibility of future USART implementations. None of the error flags can generate interrupts. The Frame Error (FE) Flag indicates the state of the first stop bit of the next readable frame stored in the receive buffer. The FE Flag is zero when the stop bit was correctly read (as one), and the FE Flag will be one when the stop bit was incorrect (zero). This flag can be used for detecting out-of-sync conditions, detecting break conditions and protocol handling. The FE Flag is not affected by the setting of the USBS bit in UCSRC since the Receiver ignores all, except for the first, stop bits. For compatibility with future devices, always set this bit to zero when writing to UCSRA. The Data OverRun (DOR) Flag indicates data loss due to a Receiver Buffer full condi- tion. A Data OverRun occurs when the receive buffer is full (two characters), it is a new character waiting in the receive Shift Register, and a new start bit is detected. If the DOR Flag is set there was one or more serial frame lost between the frame last read from UDR, and the next frame read from UDR. For compatibility with future devices, always write this bit to zero when writing to UCSRA. The DOR Flag is cleared when the frame received was successfully moved from the Shift Register to the receive buffer. The Parity Error (PE) Flag indicates that the next frame in the receive buffer had a Parity Error when received. If parity check is not enabled the PE bit will always be read zero. For compatibility with future devices, always set this bit to zero when writing to UCSRA. For more details see “Parity Bit Calculation” on page 150 and “Parity Checker” on page 157. Parity Checker The Parity Checker is active when the high USART Parity mode (UPM1) bit is set. The type of Parity Check to be performed (odd or even) is selected by the UPM0 bit. When enabled, the Parity Checker calculates the parity of the data bits in incoming frames and compares the result with the parity bit from the serial frame. The result of the check is 157 2502K–AVR–10/06
stored in the receive buffer together with the received data and stop bits. The Parity Error (PE) Flag can then be read by software to check if the frame had a Parity Error. The PE bit is set if the next character that can be read from the receive buffer had a par- ity error when received and the parity checking was enabled at that point (UPM1 = 1). This bit is valid until the receive buffer (UDR) is read. Disabling the Receiver In contrast to the Transmitter, disabling of the Receiver will be immediate. Data from ongoing receptions will therefore be lost. When disabled (i.e., the RXEN is set to zero) the Receiver will no longer override the normal function of the RxD port pin. The receiver buffer FIFO will be flushed when the Receiver is disabled. Remaining data in the buffer will be lost Flushing the Receive Buffer The receiver buffer FIFO will be flushed when the Receiver is disabled, i.e., the buffer will be emptied of its contents. Unread data will be lost. If the buffer has to be flushed during normal operation, due to for instance an error condition, read the UDR I/O loca- tion until the RXC Flag is cleared. The following code example shows how to flush the receive buffer. Assembly Code Example(1) USART_Flush: sbis UCSRA, RXC ret in r16, UDR rjmp USART_Flush C Code Example(1) void USART_Flush( void ) { unsigned char dummy; while ( UCSRA & (1<<RXC) ) dummy = UDR; } Note: 1. See “About Code Examples” on page 7. Asynchronous Data The USART includes a clock recovery and a data recovery unit for handling asynchro- Reception nous data reception. The clock recovery logic is used for synchronizing the internally generated baud rate clock to the incoming asynchronous serial frames at the RxD pin. The data recovery logic samples and low pass filters each incoming bit, thereby improv- ing the noise immunity of the Receiver. The asynchronous reception operational range depends on the accuracy of the internal baud rate clock, the rate of the incoming frames, and the frame size in number of bits. Asynchronous Clock The clock recovery logic synchronizes internal clock to the incoming serial frames. Fig- Recovery ure 73 illustrates the sampling process of the start bit of an incoming frame. The sample rate is 16 times the baud rate for normal mode, and eight times the baud rate for double speed mode. The horizontal arrows illustrate the synchronization variation due to the sampling process. Note the larger time variation when using the Double Speed mode (U2X = 1) of operation. Samples denoted zero are samples done when the RxD line is idle (i.e., no communication activity). ATmega8535(L) 158 2502K–AVR–10/06
ATmega8535(L) Figure 73. Start Bit Sampling RxD IDLE START BIT 0 Sample (U2X = 0) 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 Sample (U2X = 1) 0 1 2 3 4 5 6 7 8 1 2 When the clock recovery logic detects a high (idle) to low (start) transition on the RxD line, the start bit detection sequence is initiated. Let sample 1 denote the first zero-sam- ple as shown in the figure. The clock recovery logic then uses samples 8, 9, and 10 for normal mode, and samples 4, 5, and 6 for Double Speed mode (indicated with sample numbers inside boxes on the figure), to decide if a valid start bit is received. If two or more of these three samples have logical high levels (the majority wins), the start bit is rejected as a noise spike and the Receiver starts looking for the next high to low-transi- tion. If however, a valid start bit is detected, the clock recovery logic is synchronized and the data recovery can begin. The synchronization process is repeated for each start bit. Asynchronous Data Recovery When the receiver clock is synchronized to the start bit, the data recovery can begin. The data recovery unit uses a state machine that has 16 states for each bit in normal mode and eight states for each bit in Double Speed mode. Figure 74 shows the sam- pling of the data bits and the parity bit. Each of the samples is given a number that is equal to the state of the recovery unit. Figure 74. Sampling of Data and Parity Bit RxD BIT n Sample (U2X = 0) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 Sample (U2X = 1) 1 2 3 4 5 6 7 8 1 The decision of the logic level of the received bit is taken by doing a majority voting of the logic value to the three samples in the center of the received bit. The center samples are emphasized on the figure by having the sample number inside boxes. The majority voting process is done as follows: If two or all three samples have high levels, the received bit is registered to be a logic 1. If two or all three samples have low levels, the received bit is registered to be a logic 0. This majority voting process acts as a low pass filter for the incoming signal on the RxD pin. The recovery process is then repeated until a complete frame is received. Including the first stop bit. Note that the Receiver only uses the first stop bit of a frame. Figure 75 shows the sampling of the stop bit and the earliest possible beginning of the start bit of the next frame. 159 2502K–AVR–10/06
Figure 75. Stop Bit Sampling and Next Start Bit Sampling RxD STOP 1 (A) (B) (C) Sample (U2X = 0) 1 2 3 4 5 6 7 8 9 10 0/1 0/1 0/1 Sample (U2X = 1) 1 2 3 4 5 6 0/1 The same majority voting is done to the stop bit as done for the other bits in the frame. If the stop bit is registered to have a logic 0 value, the Frame Error (FE) Flag will be set. A new high to low transition indicating the start bit of a new frame can come right after the last of the bits used for majority voting. For Normal Speed mode, the first low level sample can be at point marked (A) in Figure 75. For Double Speed mode the first low level must be delayed to (B). (C) marks a stop bit of full length. The early start bit detec- tion influences the operational range of the Receiver. Asynchronous Operational The operational range of the Receiver is dependent on the mismatch between the Range received bit rate and the internally generated baud rate. If the Transmitter is sending frames at too fast or too slow bit rates, or the internally generated baud rate of the Receiver does not have a similar (see Table 62) base frequency, the Receiver will not be able to synchronize the frames to the start bit. The following equations can be used to calculate the ratio of the incoming data rate and internal receiver baud rate. (D+1)S (D+2)S R = ------------------------------------------- R = ----------------------------------- slow S–1+D⋅S+S fast (D+1)S+S F M D Sum of character size and parity size (D = 5 to 10 bit). S Samples per bit. S = 16 for Normal Speed mode and S = 8 for Double Speed mode. S First sample number used for majority voting. S = 8 for Normal Speed and S = 4 F F F for Double Speed mode. S Middle sample number used for majority voting. S = 9 for Normal Speed and M M S =5 for Double Speed mode. M R is the ratio of the slowest incoming data rate that can be accepted in relation to the slow receiver baud rate. R is the ratio of the fastest incoming data rate that can be fast accepted in relation to the Receiver baud rate. Table 62 and Table 63 list the maximum receiver baud rate error that can be tolerated. Note that normal speed mode has higher toleration of baud rate variations. ATmega8535(L) 160 2502K–AVR–10/06
ATmega8535(L) Table 62. Recommended Maximum Receiver Baud Rate Error for Normal Speed Mode (U2X = 0) D Max Total Recommended Max # (Data+Parity Bit) R (%) R (%) Error (%) Receiver Error (%) slow fast 5 93.20 106.67 +6.67/-6.8 ± 3.0 6 94.12 105.79 +5.79/-5.88 ± 2.5 7 94.81 105.11 +5.11 -5.19 ± 2.0 8 95.36 104.58 +4.58/-4.54 ± 2.0 9 95.81 104.14 +4.14/-4.19 ± 1.5 10 96.17 103.78 +3.78/-3.83 ± 1.5 Table 63. Recommended Maximum Receiver Baud Rate Error for Double Speed Mode (U2X = 1) D Max Total Recommended Max # (Data+Parity Bit) R (%) R (%) Error (%) Receiver Error (%) slow fast 5 94.12 105.66 +5.66/-5.88 ± 2.5 6 94.92 104.92 +4.92/-5.08 ± 2.0 7 95.52 104.35 +4.35/-4.48 ± 1.5 8 96.00 103.90 +3.90/-4.00 ± 1.5 9 96.39 103.53 +3.53/-3.61 ± 1.5 10 96.70 103.23 +3.23/-3.30 ± 1.0 The recommendations of the maximum receiver baud rate error was made under the assumption that the Receiver and Transmitter equally divides the maximum total error. There are two possible sources for the receivers baud rate error. The receiver’s system clock (XTAL) will always have some minor instability over the supply voltage range and the temperature range. When using a crystal to generate the system clock, this is rarely a problem, but for a resonator the system clock may differ more than 2% depending of the resonators tolerance. The second source for the error is more controllable. The baud rate generator can not always do an exact division of the system frequency to get the baud rate wanted. In this case an UBRR value that gives an acceptable low error can be used if possible. 161 2502K–AVR–10/06
Multi-processor Setting the Multi-processor Communication Mode (MPCM) bit in UCSRA enables a fil- Communication Mode tering function of incoming frames received by the USART Receiver. Frames that do not contain address information will be ignored and not put into the receive buffer. This effectively reduces the number of incoming frames that has to be handled by the CPU, in a system with multiple MCUs that communicate via the same serial bus. The Trans- mitter is unaffected by the MPCM setting, but has to be used differently when it is a part of a system utilizing the Multi-processor Communication Mode. If the Receiver is set up to receive frames that contain five to eight data bits, then the first stop bit indicates if the frame contains data or address information. If the Receiver is set up for frames with nine data bits, then the ninth bit (RXB8) is used for identifying address and data frames. When the frame type bit (the first stop or the ninth bit) is one, the frame contains an address. When the frame type bit is zero the frame is a data frame. The Multi-processor Communication Mode enables several slave MCUs to receive data from a Master MCU. This is done by first decoding an address frame to find out which MCU has been addressed. If a particular Slave MCU has been addressed, it will receive the following data frames as normal, while the other Slave MCUs will ignore the received frames until another address frame is received. Using MPCM For an MCU to act as a Master MCU, it can use a 9-bit character frame format (UCSZ=7). The ninth bit (TXB8) must be set when an address frame (TXB8 = 1) or cleared when a data frame (TXB = 0) is being transmitted. The Slave MCUs must, in this case, be set to use a 9-bit character frame format. The following procedure should be used to exchange data in Multi-processor Communi- cation Mode: 1. All Slave MCUs are in Multi-processor Communication Mode (MPCM in UCSRA is set). 2. The Master MCU sends an address frame, and all slaves receive and read this frame. In the Slave MCUs, the RXC Flag in UCSRA will be set as normal. 3. Each Slave MCU reads the UDR Register and determines if it has been selected. If so, it clears the MPCM bit in UCSRA, otherwise it waits for the next address byte and keeps the MPCM setting. 4. The addressed MCU will receive all data frames until a new address frame is received. The other Slave MCUs, which still have the MPCM bit set, will ignore the data frames. 5. When the last data frame is received by the addressed MCU, the addressed MCU sets the MPCM bit and waits for a new address frame from Master. The process then repeats from 2. Using any of the 5- to 8-bit character frame formats is possible, but impractical since the Receiver must change between using n and n+1 character frame formats. This makes full-duplex operation difficult since the Transmitter and Receiver uses the same charac- ter size setting. If 5- to 8-bit character frames are used, the Transmitter must be set to use two stop bit (USBS = 1) since the first stop bit is used for indicating the frame type. Do not use Read-Modify-Write instructions (SBI and CBI) to set or clear the MPCM bit. The MPCM bit shares the same I/O location as the TXC Flag and this might accidentally be cleared when using SBI or CBI instructions. ATmega8535(L) 162 2502K–AVR–10/06
ATmega8535(L) Accessing The UBRRH Register shares the same I/O location as the UCSRC Register. Therefore UBRRH/UCSRC some special consideration must be taken when accessing this I/O location. Registers Write Access When doing a write access of this I/O location, the high bit of the value written, the USART Register Select (URSEL) bit, controls which one of the two registers that will be written. If URSEL is zero during a write operation, the UBRRH value will be updated. If URSEL is one, the UCSRC setting will be updated. The following code examples show how to access the two registers. Assembly Code Examples(1) ... ; Set UBRRH to 2 ldi r16,0x02 out UBRRH,r16 ... ; Set the USBS and the UCSZ1 bit to one, and ; the remaining bits to zero. ldi r16,(1<<URSEL)|(1<<USBS)|(1<<UCSZ1) out UCSRC,r16 ... C Code Examples(1) ... /* Set UBRRH to 2 */ UBRRH = 0x02; ... /* Set the USBS and the UCSZ1 bit to one, and */ /* the remaining bits to zero. */ UCSRC = (1<<URSEL)|(1<<USBS)|(1<<UCSZ1); ... Note: 1. See “About Code Examples” on page 7. As the code examples illustrate, write accesses of the two registers are relatively unaf- fected of the sharing of I/O location. 163 2502K–AVR–10/06
Read Access Doing a read access to the UBRRH or the UCSRC Register is a more complex opera- tion. However, in most applications, it is rarely necessary to read any of these registers. The read access is controlled by a timed sequence. Reading the I/O location once returns the UBRRH Register contents. If the register location was read in previous sys- tem clock cycle, reading the register in the current clock cycle will return the UCSRC contents. Note that the timed sequence for reading the UCSRC is an atomic operation. Interrupts must therefore be controlled (e.g., by disabling interrupts globally) during the read operation. The following code example shows how to read the UCSRC Register contents. Assembly Code Example(1) USART_ReadUCSRC: ; Read UCSRC in r16,UBRRH in r16,UCSRC ret C Code Example(1) unsigned char USART_ReadUCSRC( void ) { unsigned char ucsrc; /* Read UCSRC */ ucsrc = UBRRH; ucsrc = UCSRC; return ucsrc; } Note: 1. See “About Code Examples” on page 7. The assembly code example returns the UCSRC value in r16. Reading the UBRRH contents is not an atomic operation and therefore it can be read as an ordinary register, as long as the previous instruction did not access the register location. USART Register Description USART I/O Data Register – UDR Bit 7 6 5 4 3 2 1 0 RXB[7:0] UDR (Read) TXB[7:0] UDR (Write) Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 The USART Transmit Data Buffer Register and USART Receive Data Buffer Registers share the same I/O address referred to as USART Data Register or UDR. The Transmit Data Buffer Register (TXB) will be the destination for data written to the UDR Register location. Reading the UDR Register location will return the contents of the Receive Data Buffer Register (RXB). ATmega8535(L) 164 2502K–AVR–10/06
ATmega8535(L) For 5-, 6-, or 7-bit characters the upper unused bits will be ignored by the Transmitter and set to zero by the Receiver. The transmit buffer can only be written when the UDRE Flag in the UCSRA Register is set. Data written to UDR when the UDRE Flag is not set, will be ignored by the USART Transmitter. When data is written to the transmit buffer, and the Transmitter is enabled, the Transmitter will load the data into the transmit Shift Register when the Shift Register is empty. Then the data will be serially transmitted on the TxD pin. The receive buffer consists of a two-level FIFO. The FIFO will change its state whenever the receive buffer is accessed. Due to this behavior of the receive buffer, do not use Read-Modify-Write instructions (SBI and CBI) on this location. Be careful when using bit test instructions (SBIC and SBIS), since these also will change the state of the FIFO. USART Control and Status Register A – UCSRA Bit 7 6 5 4 3 2 1 0 RXC TXC UDRE FE DOR PE U2X MPCM UCSRA Read/Write R R/W R R R R R/W R/W Initial Value 0 0 1 0 0 0 0 0 (cid:129) Bit 7 – RXC: USART Receive Complete This flag bit is set when there are unread data in the receive buffer and cleared when the receive buffer is empty (i.e., does not contain any unread data). If the Receiver is dis- abled, the receive buffer will be flushed and consequently the RXC bit will become zero. The RXC Flag can be used to generate a Receive Complete interrupt (see description of the RXCIE bit). (cid:129) Bit 6 – TXC: USART Transmit Complete This flag bit is set when the entire frame in the transmit Shift Register has been shifted out and there are no new data currently present in the transmit buffer (UDR). The TXC Flag bit is automatically cleared when a Transmit Complete interrupt is executed, or it can be cleared by writing a one to its bit location. The TXC Flag can generate a Transmit Complete interrupt (see description of the TXCIE bit). (cid:129) Bit 5 – UDRE: USART Data Register Empty The UDRE Flag indicates if the transmit buffer (UDR) is ready to receive new data. If UDRE is one, the buffer is empty, and therefore ready to be written. The UDRE Flag can generate a Data Register Empty interrupt (see description of the UDRIE bit). UDRE is set after a reset to indicate that the Transmitter is ready. (cid:129) Bit 4 – FE: Frame Error This bit is set if the next character in the receive buffer had a Frame Error when received. For example, when the first stop bit of the next character in the receive buffer is zero. This bit is valid until the receive buffer (UDR) is read. The FE bit is zero when the stop bit of received data is one. Always set this bit to zero when writing to UCSRA. (cid:129) Bit 3 – DOR: Data OverRun This bit is set if a data overrun condition is detected. A Data OverRun occurs when the receive buffer is full (two characters), it is a new character waiting in the receive Shift Register, and a new start bit is detected. This bit is valid until the receive buffer (UDR) is read. Always set this bit to zero when writing to UCSRA. (cid:129) Bit 2 – PE: Parity Error This bit is set if the next character in the receive buffer had a Parity Error when received and the parity checking was enabled at that point (UPM1 = 1). This bit is valid until the receive buffer (UDR) is read. Always set this bit to zero when writing to UCSRA. 165 2502K–AVR–10/06
(cid:129) Bit 1 – U2X: Double the USART Transmission Speed This bit only has effect for the asynchronous operation. Write this bit to zero when using synchronous operation. Writing this bit to one will reduce the divisor of the baud rate divider from 16 to 8 effec- tively doubling the transfer rate for asynchronous communication. (cid:129) Bit 0 – MPCM: Multi-processor Communication Mode This bit enables the Multi-processor Communication mode. When the MPCM bit is writ- ten to one, all the incoming frames received by the USART Receiver that do not contain address information will be ignored. The Transmitter is unaffected by the MPCM setting. For more detailed information see “Multi-processor Communication Mode” on page 162. USART Control and Status Register B – UCSRB Bit 7 6 5 4 3 2 1 0 RXCIE TXCIE UDRIE RXEN TXEN UCSZ2 RXB8 TXB8 UCSRB Read/Write R/W R/W R/W R/W R/W R/W R R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 7 – RXCIE: RX Complete Interrupt Enable Writing this bit to one enables interrupt on the RXC Flag. A USART Receive Complete interrupt will be generated only if the RXCIE bit is written to one, the Global Interrupt Flag in SREG is written to one and the RXC bit in UCSRA is set. (cid:129) Bit 6 – TXCIE: TX Complete Interrupt Enable Writing this bit to one enables interrupt on the TXC Flag. A USART Transmit Complete interrupt will be generated only if the TXCIE bit is written to one, the Global Interrupt Flag in SREG is written to one and the TXC bit in UCSRA is set. (cid:129) Bit 5 – UDRIE: USART Data Register Empty Interrupt Enable Writing this bit to one enables interrupt on the UDRE Flag. A Data Register Empty inter- rupt will be generated only if the UDRIE bit is written to one, the Global Interrupt Flag in SREG is written to one and the UDRE bit in UCSRA is set. (cid:129) Bit 4 – RXEN: Receiver Enable Writing this bit to one enables the USART Receiver. The Receiver will override normal port operation for the RxD pin when enabled. Disabling the Receiver will flush the receive buffer invalidating the FE, DOR, and PE Flags. (cid:129) Bit 3 – TXEN: Transmitter Enable Writing this bit to one enables the USART Transmitter. The Transmitter will override nor- mal port operation for the TxD pin when enabled. The disabling of the Transmitter (writing TXEN to zero) will not become effective until ongoing and pending transmis- sions are completed, (i.e., when the transmit Shift Register and transmit Buffer Register do not contain data to be transmitted). When disabled, the Transmitter will no longer override the TxD port. (cid:129) Bit 2 – UCSZ2: Character Size The UCSZ2 bits combined with the UCSZ1:0 bit in UCSRC sets the number of data bits (Character Size) in a frame the Receiver and Transmitter use. (cid:129) Bit 1 – RXB8: Receive Data Bit 8 RXB8 is the ninth data bit of the received character when operating with serial frames with nine data bits. Must be read before reading the low bits from UDR. (cid:129) Bit 0 – TXB8: Transmit Data Bit 8 ATmega8535(L) 166 2502K–AVR–10/06
ATmega8535(L) TXB8 is the ninth data bit in the character to be transmitted when operating with serial frames with nine data bits. Must be written before writing the low bits to UDR. USART Control and Status Register C – UCSRC(1) Bit 7 6 5 4 3 2 1 0 URSEL UMSEL UPM1 UPM0 USBS UCSZ1 UCSZ0 UCPOL UCSRC Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 1 0 0 0 0 1 1 0 Note: 1. The UCSRC Register shares the same I/O location as the UBRRH Register. See the “Accessing UBRRH/UCSRC Registers” on page 163 section which describes how to access this register. (cid:129) Bit 7 – URSEL: Register Select This bit selects between accessing the UCSRC or the UBRRH Register. It is read as one when reading UCSRC. The URSEL must be one when writing the UCSRC. (cid:129) Bit 6 – UMSEL: USART Mode Select This bit selects between asynchronous and synchronous mode of operation. Table 64. UMSEL Bit Settings UMSEL Mode 0 Asynchronous Operation 1 Synchronous Operation 167 2502K–AVR–10/06
(cid:129) Bit 5:4 – UPM1:0: Parity Mode These bits enable and set type of parity generation and check. If enabled, the Transmit- ter will automatically generate and send the parity of the transmitted data bits within each frame. The Receiver will generate a parity value for the incoming data and com- pare it to the UPM0 setting. If a mismatch is detected, the PE Flag in UCSRA will be set. Table 65. UPM Bits Settings UPM1 UPM0 Parity Mode 0 0 Disabled 0 1 Reserved 1 0 Enabled, Even Parity 1 1 Enabled, Odd Parity (cid:129) Bit 3 – USBS: Stop Bit Select This bit selects the number of stop bits to be inserted by the Transmitter. The Receiver ignores this setting. Table 66. USBS Bit Settings USBS Stop Bit(s) 0 1-bit 1 2-bit (cid:129) Bit 2:1 – UCSZ1:0: Character Size The UCSZ1:0 bits combined with the UCSZ2 bit in UCSRB sets the number of data bits (character size) in a frame the Receiver and Transmitter use. Table 67. UCSZ Bits Settings UCSZ2 UCSZ1 UCSZ0 Character Size 0 0 0 5-bit 0 0 1 6-bit 0 1 0 7-bit 0 1 1 8-bit 1 0 0 Reserved 1 0 1 Reserved 1 1 0 Reserved 1 1 1 9-bit (cid:129) Bit 0 – UCPOL: Clock Polarity ATmega8535(L) 168 2502K–AVR–10/06
ATmega8535(L) This bit is used for Synchronous mode only. Write this bit to zero when asynchronous mode is used. The UCPOL bit sets the relationship between data output change and data input sample, and the synchronous clock (XCK). Table 68. UCPOL Bit Settings Transmitted Data Changed Received Data Sampled UCPOL (Output of TxD Pin) (Input on RxD Pin) 0 Rising XCK Edge Falling XCK Edge 1 Falling XCK Edge Rising XCK Edge USART Baud Rate Registers – UBRRL and UBRRH(1) Bit 15 14 13 12 11 10 9 8 URSEL – – – UBRR[11:8] UBRRH UBRR[7:0] UBRRL 7 6 5 4 3 2 1 0 Read/Write R/W R R R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Note: 1. The UBRRH Register shares the same I/O location as the UCSRC Register. See the “Accessing UBRRH/UCSRC Registers” on page 163 section which describes how to access this register. (cid:129) Bit 15 – URSEL: Register Select This bit selects between accessing the UBRRH or the UCSRC Register. It is read as zero when reading UBRRH. The URSEL must be zero when writing the UBRRH. (cid:129) Bit 14:12 – Reserved Bits These bits are reserved for future use. For compatibility with future devices, these bit must be written to zero when UBRRH is written. (cid:129) Bit 11:0 – UBRR11:0: USART Baud Rate Register This is a 12-bit register which contains the USART Baud Rate. The UBRRH contains the four most significant bits, and the UBRRL contains the eight least significant bits of the USART baud rate. Ongoing transmissions by the Transmitter and Receiver will be cor- rupted if the baud rate is changed. Writing UBRRL will trigger an immediate update of the baud rate prescaler. 169 2502K–AVR–10/06
Examples of Baud Rate For standard crystal and resonator frequencies, the most commonly used baud rates for Setting asynchronous operation can be generated by using the UBRR settings in Table 69. UBRR values which yield an actual baud rate differing less than 0.5% from the target baud rate, are bold in the table. Higher error ratings are acceptable, but the Receiver will have less noise resistance when the error ratings are high, especially for large serial frames (see “Asynchronous Operational Range” on page 160). The error values are cal- culated using the following equation: BaudRate Error[%] = ⎛---------------------------C----l-o--s---e--s---t- -M----a---t-c--h--–1⎞ •100% ⎝ BaudRate ⎠ Table 69. Examples of UBRR Settings for Commonly Used Oscillator Frequencies f = 1.0000 MHz f = 1.8432 MHz f = 2.0000 MHz osc osc osc Baud U2X = 0 U2X = 1 U2X = 0 U2X = 1 U2X = 0 U2X = 1 Rate (bps) UBRR Error UBRR Error UBRR Error UBRR Error UBRR Error UBRR Error 2400 25 0.2% 51 0.2% 47 0.0% 95 0.0% 51 0.2% 103 0.2% 4800 12 0.2% 25 0.2% 23 0.0% 47 0.0% 25 0.2% 51 0.2% 9600 6 -7.0% 12 0.2% 11 0.0% 23 0.0% 12 0.2% 25 0.2% 14.4k 3 8.5% 8 -3.5% 7 0.0% 15 0.0% 8 -3.5% 16 2.1% 19.2k 2 8.5% 6 -7.0% 5 0.0% 11 0.0% 6 -7.0% 12 0.2% 28.8k 1 8.5% 3 8.5% 3 0.0% 7 0.0% 3 8.5% 8 -3.5% 38.4k 1 -18.6% 2 8.5% 2 0.0% 5 0.0% 2 8.5% 6 -7.0% 57.6k 0 8.5% 1 8.5% 1 0.0% 3 0.0% 1 8.5% 3 8.5% 76.8k – – 1 -18.6% 1 -25.0% 2 0.0% 1 -18.6% 2 8.5% 115.2k – – 0 8.5% 0 0.0% 1 0.0% 0 8.5% 1 8.5% 230.4k – – – – – – 0 0.0% – – – – 250k – – – – – – – – – – 0 0.0% Max (1) 62.5 kbps 125 kbps 115.2 kbps 230.4 kbps 125 kbps 250 kbps 1. UBRR = 0, Error = 0.0% ATmega8535(L) 170 2502K–AVR–10/06
ATmega8535(L) Table 70. Examples of UBRR Settings for Commonly Used Oscillator Frequencies (Continued) f = 3.6864 MHz f = 4.0000 MHz f = 7.3728 MHz osc osc osc Baud U2X = 0 U2X = 1 U2X = 0 U2X = 1 U2X = 0 U2X = 1 Rate (bps) UBRR Error UBRR Error UBRR Error UBRR Error UBRR Error UBRR Error 2400 95 0.0% 191 0.0% 103 0.2% 207 0.2% 191 0.0% 383 0.0% 4800 47 0.0% 95 0.0% 51 0.2% 103 0.2% 95 0.0% 191 0.0% 9600 23 0.0% 47 0.0% 25 0.2% 51 0.2% 47 0.0% 95 0.0% 14.4k 15 0.0% 31 0.0% 16 2.1% 34 -0.8% 31 0.0% 63 0.0% 19.2k 11 0.0% 23 0.0% 12 0.2% 25 0.2% 23 0.0% 47 0.0% 28.8k 7 0.0% 15 0.0% 8 -3.5% 16 2.1% 15 0.0% 31 0.0% 38.4k 5 0.0% 11 0.0% 6 -7.0% 12 0.2% 11 0.0% 23 0.0% 57.6k 3 0.0% 7 0.0% 3 8.5% 8 -3.5% 7 0.0% 15 0.0% 76.8k 2 0.0% 5 0.0% 2 8.5% 6 -7.0% 5 0.0% 11 0.0% 115.2k 1 0.0% 3 0.0% 1 8.5% 3 8.5% 3 0.0% 7 0.0% 230.4k 0 0.0% 1 0.0% 0 8.5% 1 8.5% 1 0.0% 3 0.0% 250k 0 -7.8% 1 -7.8% 0 0.0% 1 0.0% 1 -7.8% 3 -7.8% 0.5M – – 0 -7.8% – – 0 0.0% 0 -7.8% 1 -7.8% 1M – – – – – – – – – – 0 -7.8% Max (1) 230.4 kbps 460.8 kbps 250k bps 0.5 Mbps 460.8 kbps 921.6 kbps 1. UBRR = 0, Error = 0.0% 171 2502K–AVR–10/06
Table 71. Examples of UBRR Settings for Commonly Used Oscillator Frequencies (Continued) f = 8.0000 MHz f = 11.0592 MHz f = 14.7456 MHz osc osc osc Baud U2X = 0 U2X = 1 U2X = 0 U2X = 1 U2X = 0 U2X = 1 Rate (bps) UBRR Error UBRR Error UBRR Error UBRR Error UBRR Error UBRR Error 2400 207 0.2% 416 -0.1% 287 0.0% 575 0.0% 383 0.0% 767 0.0% 4800 103 0.2% 207 0.2% 143 0.0% 287 0.0% 191 0.0% 383 0.0% 9600 51 0.2% 103 0.2% 71 0.0% 143 0.0% 95 0.0% 191 0.0% 14.4k 34 -0.8% 68 0.6% 47 0.0% 95 0.0% 63 0.0% 127 0.0% 19.2k 25 0.2% 51 0.2% 35 0.0% 71 0.0% 47 0.0% 95 0.0% 28.8k 16 2.1% 34 -0.8% 23 0.0% 47 0.0% 31 0.0% 63 0.0% 38.4k 12 0.2% 25 0.2% 17 0.0% 35 0.0% 23 0.0% 47 0.0% 57.6k 8 -3.5% 16 2.1% 11 0.0% 23 0.0% 15 0.0% 31 0.0% 76.8k 6 -7.0% 12 0.2% 8 0.0% 17 0.0% 11 0.0% 23 0.0% 115.2k 3 8.5% 8 -3.5% 5 0.0% 11 0.0% 7 0.0% 15 0.0% 230.4k 1 8.5% 3 8.5% 2 0.0% 5 0.0% 3 0.0% 7 0.0% 250k 1 0.0% 3 0.0% 2 -7.8% 5 -7.8% 3 -7.8% 6 5.3% 0.5M 0 0.0% 1 0.0% – – 2 -7.8% 1 -7.8% 3 -7.8% 1M – – 0 0.0% – – – – 0 -7.8% 1 -7.8% Max (1) 0.5 Mbps 1 Mbps 691.2 kbps 1.3824 Mbps 921.6 kbps 1.8432 Mbps 1. UBRR = 0, Error = 0.0% ATmega8535(L) 172 2502K–AVR–10/06
ATmega8535(L) Table 72. Examples of UBRR Settings for Commonly Used Oscillator Frequencies (Continued) f = 16.0000 MHz f = 18.4320 MHz f = 20.0000 MHz osc osc osc Baud U2X = 0 U2X = 1 U2X = 0 U2X = 1 U2X = 0 U2X = 1 Rate (bps) UBRR Error UBRR Error UBRR Error UBRR Error UBRR Error UBRR Error 2400 416 -0.1% 832 0.0% 479 0.0% 959 0.0% 520 0.0% 1041 0.0% 4800 207 0.2% 416 -0.1% 239 0.0% 479 0.0% 259 0.2% 520 0.0% 9600 103 0.2% 207 0.2% 119 0.0% 239 0.0% 129 0.2% 259 0.2% 14.4k 68 0.6% 138 -0.1% 79 0.0% 159 0.0% 86 -0.2% 173 -0.2% 19.2k 51 0.2% 103 0.2% 59 0.0% 119 0.0% 64 0.2% 129 0.2% 28.8k 34 -0.8% 68 0.6% 39 0.0% 79 0.0% 42 0.9% 86 -0.2% 38.4k 25 0.2% 51 0.2% 29 0.0% 59 0.0% 32 -1.4% 64 0.2% 57.6k 16 2.1% 34 -0.8% 19 0.0% 39 0.0% 21 -1.4% 42 0.9% 76.8k 12 0.2% 25 0.2% 14 0.0% 29 0.0% 15 1.7% 32 -1.4% 115.2k 8 -3.5% 16 2.1% 9 0.0% 19 0.0% 10 -1.4% 21 -1.4% 230.4k 3 8.5% 8 -3.5% 4 0.0% 9 0.0% 4 8.5% 10 -1.4% 250k 3 0.0% 7 0.0% 4 -7.8% 8 2.4% 4 0.0% 9 0.0% 0.5M 1 0.0% 3 0.0% – – 4 -7.8% – – 4 0.0% 1M 0 0.0% 1 0.0% – – – – – – – – Max (1) 1 Mbps 2 Mbps 1.152 Mbps 2.304 Mbps 1.25 Mbps 2.5 Mbps 1. UBRR = 0, Error = 0.0% 173 2502K–AVR–10/06
Two-wire Serial Interface Features (cid:129) Simple yet Powerful and Flexible Communication Interface, only Two Bus Lines Needed (cid:129) Both Master and Slave Operation Supported (cid:129) Device can Operate as Transmitter or Receiver (cid:129) 7-bit Address Space Allows up to 128 Different Slave Addresses (cid:129) Multi-master Arbitration Support (cid:129) Up to 400 kHz Data Transfer Speed (cid:129) Slew-rate Limited Output Drivers (cid:129) Noise Suppression Circuitry Rejects Spikes on Bus Lines (cid:129) Fully Programmable Slave Address with General Call Support (cid:129) Address Recognition Causes Wake-up when AVR is in Sleep Mode Two-wire Serial Interface The Two-wire Serial Interface (TWI) is ideally suited for typical microcontroller applica- Bus Definition tions. The TWI protocol allows the systems designer to interconnect up to 128 different devices using only two bi-directional bus lines, one for clock (SCL) and one for data (SDA). The only external hardware needed to implement the bus is a single pull-up resistor for each of the TWI bus lines. All devices connected to the bus have individual addresses, and mechanisms for resolving bus contention are inherent in the TWI protocol. Figure 76. TWI Bus Interconnection V CC Device 1 Device 2 Device 3 ........ Device n R1 R2 SDA SCL TWI Terminology The following definitions are frequently encountered in this section. Table 73. TWI Terminology Term Description Master The device that initiates and terminates a transmission. The Master also generates the SCL clock. Slave The device addressed by a Master. Transmitter The device placing data on the bus. Receiver The device reading data from the bus. ATmega8535(L) 174 2502K–AVR–10/06
ATmega8535(L) Electrical Interconnection As depicted in Figure 76, both bus lines are connected to the positive supply voltage through pull-up resistors. The bus drivers of all TWI-compliant devices are open-drain or open-collector. This implements a wired-AND function which is essential to the opera- tion of the interface. A low level on a TWI bus line is generated when one or more TWI devices output a zero. A high level is output when all TWI devices tri-state their outputs, allowing the pull-up resistors to pull the line high. Note that all AVR devices connected to the TWI bus must be powered in order to allow any bus operation. The number of devices that can be connected to the bus is only limited by the bus capacitance limit of 400 pF and the 7-bit slave address space. A detailed specification of the electrical characteristics of the TWI is given in “Two-wire Serial Interface Character- istics” on page 259. Two different sets of specifications are presented there, one relevant for bus speeds below 100 kHz, and one valid for bus speeds up to 400 kHz. Data Transfer and Frame Format Transferring Bits Each data bit transferred on the TWI bus is accompanied by a pulse on the clock line. The level of the data line must be stable when the clock line is high. The only exception to this rule is for generating start and stop conditions. Figure 77. Data Validity SDA SCL Data Stable Data Stable Data Change START and STOP Conditions The Master initiates and terminates a data transmission. The transmission is initiated when the Master issues a START condition on the bus, and it is terminated when the Master issues a STOP condition. Between a START and a STOP condition, the bus is considered busy, and no other Master should try to seize control of the bus. A special case occurs when a new START condition is issued between a START and STOP con- dition. This is referred to as a REPEATED START condition, and is used when the Master wishes to initiate a new transfer without relinquishing control of the bus. After a REPEATED START, the bus is considered busy until the next STOP. This is identical to the START behavior, and therefore START is used to describe both START and REPEATED START for the remainder of this datasheet, unless otherwise noted. As depicted below, START and STOP conditions are signalled by changing the level of the SDA line when the SCL line is high. 175 2502K–AVR–10/06
Figure 78. START, REPEATED START, and STOP Conditions SDA SCL START STOP START REPEATED START STOP Address Packet Format All address packets transmitted on the TWI bus are nine bits long, consisting of seven address bits, one READ/WRITE control bit and an acknowledge bit. If the READ/WRITE bit is set, a read operation is to be performed, otherwise a write operation should be per- formed. When a Slave recognizes that it is being addressed, it should acknowledge by pulling SDA low in the ninth SCL (ACK) cycle. If the addressed slave is busy, or for some other reason can not service the master’s request, the SDA line should be left high in the ACK clock cycle. The Master can then transmit a STOP condition, or a REPEATED START condition to initiate a new transmission. An address packet consist- ing of a slave address and a READ or a WRITE bit is called SLA+R or SLA+W, respectively. The MSB of the address byte is transmitted first. Slave addresses can freely be allo- cated by the designer, but the address 0000 000 is reserved for a general call. When a general call is issued, all slaves should respond by pulling the SDA line low in the ACK cycle. A general call is used when a Master wishes to transmit the same mes- sage to several slaves in the system. When the general call address followed by a Write bit is transmitted on the bus, all slaves set up to acknowledge the general call will pull the SDA line low in the ack cycle. The following data packets will then be received by all the slaves that acknowledged the general call. Note that transmitting the general call address followed by a Read bit is meaningless, as this would cause contention if several slaves started transmitting different data. All addresses of the format 1111 xxx should be reserved for future purposes. Figure 79. Address Packet Format Addr MSB Addr LSB R/W ACK SDA SCL 1 2 7 8 9 START Data Packet Format All data packets transmitted on the TWI bus are nine bits long, consisting of one data byte and an acknowledge bit. During a data transfer, the Master generates the clock and the START and STOP conditions, while the Receiver is responsible for acknowledging the reception. An Acknowledge (ACK) is signalled by the Receiver pulling the SDA line low during the ninth SCL cycle. If the Receiver leaves the SDA line high, a NACK is sig- nalled. When the Receiver has received the last byte, or for some reason cannot receive any more bytes, it should inform the Transmitter by sending a NACK after the final byte. The MSB of the data byte is transmitted first. ATmega8535(L) 176 2502K–AVR–10/06
ATmega8535(L) Figure 80. Data Packet Format Data MSB Data LSB ACK Aggregate SDA SDA From Transmitter SDA From Receiver SCL From Master 1 2 7 8 9 STOP, REPEATED SLA+R/W Data Byte START or Next Data Byte Combining Address and Data A transmission basically consists of a START condition, a SLA+R/W, one or more data Packets into a Transmission packets and a STOP condition. An empty message, consisting of a START followed by a STOP condition is illegal. Note that the wired-ANDing of the SCL line can be used to implement handshaking between the Master and the Slave. The Slave can extend the SCL low period by pulling the SCL line low. This is useful if the clock speed set up by the Master is too fast for the Slave or the Slave needs extra time for processing between the data transmissions. The Slave extending the SCL low period will not affect the SCL high period, which is determined by the Master. As a consequence, the Slave can reduce the TWI data transfer speed by prolonging the SCL duty cycle. Figure 81 shows a typical data transmission. Note that several data bytes can be trans- mitted between the SLA+R/W and the STOP condition, depending on the software protocol implemented by the application software. Figure 81. Typical Data Transmission Addr MSB Addr LSB R/W ACK Data MSB Data LSB ACK SDA SCL 1 2 7 8 9 1 2 7 8 9 START SLA+R/W Data Byte STOP Multi-master Bus The TWI protocol allows bus systems with several masters. Special concerns have Systems, Arbitration and been taken in order to ensure that transmissions will proceed as normal, even if two or Synchronization more masters initiate a transmission at the same time. Two problems arise in multi-mas- ter systems: (cid:129) An algorithm must be implemented allowing only one of the Masters to complete the transmission. All other masters should cease transmission when they discover that they have lost the selection process. This selection process is called arbitration. When a contending Master discovers that it has lost the arbitration process, it should immediately switch to Slave mode to check whether it is being addressed by the winning Master. The fact that multiple masters have started transmission at the same time should not be detectable to the slaves, i.e., the data being transferred on the bus must not be corrupted. (cid:129) Different Masters may use different SCL frequencies. A scheme must be devised to synchronize the serial clocks from all Masters, in order to let the transmission proceed in a lockstep fashion. This will facilitate the arbitration process. The wired-ANDing of the bus lines is used to solve both these problems. The serial clocks from all Masters will be wired-ANDed, yielding a combined clock with a high 177 2502K–AVR–10/06
period equal to the one from the Master with the shortest high period. The low period of the combined clock is equal to the low period of the Master with the longest low period. Note that all masters listen to the SCL line, effectively starting to count their SCL high and low time-out periods when the combined SCL line goes high or low, respectively. Figure 82. SCL Synchronization Between Multiple Masters TA TA low high SCL From Master A SCL From Master B SCL Bus Line TB TB low high Masters Start Masters Start Counting Low Period Counting High Period Arbitration is carried out by all masters continuously monitoring the SDA line after out- putting data. If the value read from the SDA line does not match the value the Master had output, it has lost the arbitration. Note that a Master can only lose arbitration when it outputs a high SDA value while another Master outputs a low value. The losing master should immediately go to Slave mode, checking if it is being addressed by the winning master. The SDA line should be left high, but losing masters are allowed to generate a clock signal until the end of the current data or address packet. Arbitration will continue until only one master remains, and this may take many bits. If several masters are trying to address the same Slave, arbitration will continue into the data packet. Figure 83. Arbitration Between Two Masters START Master A Loses Arbitration, SDA SDA SDA From A Master A SDA From Master B SDA Line Synchronized SCL Line ATmega8535(L) 178 2502K–AVR–10/06
ATmega8535(L) Note that arbitration is not allowed between: (cid:129) A REPEATED START condition and a data bit (cid:129) A STOP condition and a data bit (cid:129) A REPEATED START and a STOP condition It is the user software’s responsibility to ensure that these illegal arbitration conditions never occur. This implies that in multi-master systems, all data transfers must use the same composition of SLA+R/W and data packets. In other words: All transmissions must contain the same number of data packets, otherwise the result of the arbitration is undefined. Overview of the TWI The TWI module is comprised of several submodules, as shown in Figure 84. All regis- Module ters drawn in a thick line are accessible through the AVR data bus. Figure 84. Overview of the TWI Module SCL SDA Slew-rate Spike Slew-rate Spike Control Filter Control Filter Bus Interface Unit Bit Rate Generator START / STOP Spike Suppression Prescaler Control Address/Data Shift Bit Rate Register Arbitration detection Ack Register (TWDR) (TWBR) Address Match Unit Control Unit Address Register Status Register Control Register (TWAR) (TWSR) (TWCR) TWI Unit State Machine and Address Comparator Status control SCL and SDA Pins These pins interface the AVR TWI with the rest of the MCU system. The output drivers contain a slew-rate limiter in order to conform to the TWI specification. The input stages contain a spike suppression unit removing spikes shorter than 50 ns. Note that the inter- nal pull-ups in the AVR pads can be enabled by setting the PORT bits corresponding to the SCL and SDA pins, as explained in the I/O Port section. The internal pull-ups can in some systems eliminate the need for external ones. 179 2502K–AVR–10/06
Bit Rate Generator Unit This unit controls the period of SCL when operating in a Master mode. The SCL period is controlled by settings in the TWI Bit Rate Register (TWBR) and the Prescaler bits in the TWI Status Register (TWSR). Slave operation does not depend on Bit Rate or Pres- caler settings, but the CPU clock frequency in the Slave must be at least 16 times higher than the SCL frequency. Note that slaves may prolong the SCL low period, thereby reducing the average TWI bus clock period. The SCL frequency is generated according to the following equation: CPU Clock frequency SCL frequency = ----------------------------------------------------------- TWPS 16+2(TWBR)⋅4 (cid:129) TWBR = Value of the TWI Bit Rate Register (cid:129) TWPS = Value of the prescaler bits in the TWI Status Register Note: Pull-up resistor values should be selected according to the SCL frequency and the capacitive bus line load. See Table 112 on page 259 for value of pull-up resistor. Bus Interface Unit This unit contains the Data and Address Shift Register (TWDR), a START/STOP Con- troller and Arbitration detection hardware. The TWDR contains the address or data bytes to be transmitted, or the address or data bytes received. In addition to the 8-bit TWDR, the Bus Interface Unit also contains a register containing the (N)ACK bit to be transmitted or received. This (N)ACK Register is not directly accessible by the applica- tion software. However, when receiving, it can be set or cleared by manipulating the TWI Control Register (TWCR). When in Transmitter mode, the value of the received (N)ACK bit can be determined by the value in the TWSR. The START/STOP Controller is responsible for generation and detection of START, REPEATED START, and STOP conditions. The START/STOP controller is able to detect START and STOP conditions even when the AVR MCU is in one of the sleep modes, enabling the MCU to wake up if addressed by a Master. If the TWI has initiated a transmission as Master, the Arbitration Detection hardware continuously monitors the transmission trying to determine if arbitration is in process. If the TWI has lost an arbitration, the Control Unit is informed. Correct action can then be taken and appropriate status codes generated. Address Match Unit The Address Match unit checks if received address bytes match the 7-bit address in the TWI Address Register (TWAR). If the TWI General Call Recognition Enable (TWGCE) bit in the TWAR is written to one, all incoming address bits will also be compared against the General Call address. Upon an address match, the Control Unit is informed, allowing correct action to be taken. The TWI may or may not acknowledge its address, depending on settings in the TWCR. The Address Match unit is able to compare addresses even when the AVR MCU is in sleep mode, enabling the MCU to wake up if addressed by a Master. Control Unit The Control unit monitors the TWI bus and generates responses corresponding to set- tings in the TWI Control Register (TWCR). When an event requiring the attention of the application occurs on the TWI bus, the TWI Interrupt Flag (TWINT) is asserted. In the next clock cycle, the TWI Status Register (TWSR) is updated with a status code identify- ing the event. The TWSR only contains relevant status information when the TWI Interrupt Flag is asserted. At all other times, the TWSR contains a special status code indicating that no relevant status information is available. As long as the TWINT Flag is set, the SCL line is held low. This allows the application software to complete its tasks before allowing the TWI transmission to continue. The TWINT Flag is set in the following situations: ATmega8535(L) 180 2502K–AVR–10/06
ATmega8535(L) (cid:129) After the TWI has transmitted a START/REPEATED START condition. (cid:129) After the TWI has transmitted SLA+R/W. (cid:129) After the TWI has transmitted an address byte. (cid:129) After the TWI has lost arbitration. (cid:129) After the TWI has been addressed by own Slave address or general call. (cid:129) After the TWI has received a data byte. (cid:129) After a STOP or REPEATED START has been received while still addressed as a Slave. (cid:129) When a bus error has occurred due to an illegal START or STOP condition. TWI Register Description TWI Bit Rate Register – TWBR Bit 7 6 5 4 3 2 1 0 TWBR7 TWBR6 TWBR5 TWBR4 TWBR3 TWBR2 TWBR1 TWBR0 TWBR Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bits 7..0 – TWI Bit Rate Register TWBR selects the division factor for the bit rate generator. The bit rate generator is a frequency divider which generates the SCL clock frequency in the Master modes. See “Bit Rate Generator Unit” on page 180 for calculating bit rates. TWI Control Register – TWCR Bit 7 6 5 4 3 2 1 0 TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE TWCR Read/Write R/W R/W R/W R/W R R/W R R/W Initial Value 0 0 0 0 0 0 0 0 The TWCR is used to control the operation of the TWI. It is used to enable the TWI, to initiate a master access by applying a START condition to the bus, to generate a receiver acknowledge, to generate a stop condition, and to control halting of the bus while the data to be written to the bus are written to the TWDR. It also indicates a write collision if data is attempted written to TWDR while the register is inaccessible. (cid:129) Bit 7 – TWINT: TWI Interrupt Flag This bit is set by hardware when the TWI has finished its current job and expects appli- cation software response. If the I-bit in SREG and TWIE in TWCR are set, the MCU will jump to the TWI Interrupt Vector. While the TWINT Flag is set, the SCL low period is stretched. The TWINT Flag must be cleared by software by writing a logic one to it. Note that this flag is not automatically cleared by hardware when executing the interrupt rou- tine. Also note that clearing this flag starts the operation of the TWI, so all accesses to the TWI Address Register (TWAR), TWI Status Register (TWSR), and TWI Data Regis- ter (TWDR) must be complete before clearing this flag. (cid:129) Bit 6 – TWEA: TWI Enable Acknowledge Bit The TWEA bit controls the generation of the acknowledge pulse. If the TWEA bit is writ- ten to one, the ACK pulse is generated on the TWI bus if the following conditions are met: 1. The device’s own slave address has been received. 2. A general call has been received, while the TWGCE bit in the TWAR is set. 3. A data byte has been received in Master Receiver or Slave Receiver mode. 181 2502K–AVR–10/06
By writing the TWEA bit to zero, the device can be virtually disconnected from the Two- wire Serial Bus temporarily. Address recognition can then be resumed by writing the TWEA bit to one again. (cid:129) Bit 5 – TWSTA: TWI START Condition Bit The application writes the TWSTA bit to one when it desires to become a Master on the Two-wire Serial Bus. The TWI hardware checks if the bus is available, and generates a START condition on the bus if it is free. However, if the bus is not free, the TWI waits until a STOP condition is detected, and then generates a new START condition to claim the bus Master status. TWSTA must be cleared by software when the START condition has been transmitted. (cid:129) Bit 4 – TWSTO: TWI STOP Condition Bit Writing the TWSTO bit to one in Master mode will generate a STOP condition on the Two-wire Serial Bus. When the STOP condition is executed on the bus, the TWSTO bit is cleared automatically. In Slave mode, setting the TWSTO bit can be used to recover from an error condition. This will not generate a STOP condition, but the TWI returns to a well-defined unaddressed Slave mode and releases the SCL and SDA lines to a high impedance state. (cid:129) Bit 3 – TWWC: TWI Write Collision Flag The TWWC bit is set when attempting to write to the TWI Data Register – TWDR when TWINT is low. This flag is cleared by writing the TWDR Register when TWINT is high. (cid:129) Bit 2 – TWEN: TWI Enable Bit The TWEN bit enables TWI operation and activates the TWI interface. When TWEN is written to one, the TWI takes control over the I/O pins connected to the SCL and SDA pins, enabling the slew-rate limiters and spike filters. If this bit is written to zero, the TWI is switched off and all TWI transmissions are terminated, regardless of any ongoing operation. (cid:129) Bit 1 – Res: Reserved Bit This bit is a reserved bit and will always read as zero. (cid:129) Bit 0 – TWIE: TWI Interrupt Enable When this bit is written to one, and the I-bit in SREG is set, the TWI interrupt request will be activated for as long as the TWINT flag is high. ATmega8535(L) 182 2502K–AVR–10/06
ATmega8535(L) TWI Status Register – TWSR Bit 7 6 5 4 3 2 1 0 TWS7 TWS6 TWS5 TWS4 TWS3 – TWPS1 TWPS0 TWSR Read/Write R R R R R R R/W R/W Initial Value 1 1 1 1 1 0 0 0 (cid:129) Bits 7..3 – TWS: TWI Status These five bits reflect the status of the TWI logic and the Two-wire Serial Bus. The dif- ferent status codes are described later in this section. Note that the value read from TWSR contains both the 5-bit status value and the 2-bit prescaler value. The application designer should mask the prescaler bits to zero when checking the status bits. This makes status checking independent of prescaler setting. This approach is used in this datasheet, unless otherwise noted. (cid:129) Bit 2 – Res: Reserved bit This bit is reserved and will always read as zero. (cid:129) Bits 1..0 – TWPS: TWI Prescaler Bits These bits can be read and written, and control the bit rate prescaler. Table 74. TWI Bit Rate Prescaler TWPS1 TWPS0 Prescaler Value 0 0 1 0 1 4 1 0 16 1 1 64 To calculate bit rates, see “Bit Rate Generator Unit” on page 180. The value of TWPS1..0 is used in the equation. TWI Data Register – TWDR Bit 7 6 5 4 3 2 1 0 TWD7 TWD6 TWD5 TWD4 TWD3 TWD2 TWD1 TWD0 TWDR Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 1 1 1 1 1 1 1 1 In Transmit mode, TWDR contains the next byte to be transmitted. In Receive mode, the TWDR contains the last byte received. It is writable while the TWI is not in the process of shifting a byte. This occurs when the TWI Interrupt Flag (TWINT) is set by hardware. Note that the Data Register cannot be initialized by the user before the first interrupt occurs. The data in TWDR remains stable as long as TWINT is set. While data is shifted out, data on the bus is simultaneously shifted in. TWDR always contains the last byte present on the bus, except after a wake-up from a sleep mode by the TWI interrupt. In this case, the contents of TWDR is undefined. In the case of a lost bus arbitration, no data is lost in the transition from Master to Slave. Handling of the ACK bit is controlled automatically by the TWI logic, the CPU cannot access the ACK bit directly. (cid:129) Bits 7..0 – TWD: TWI Data Register These eight bits constitute the next data byte to be transmitted, or the latest data byte received on the Two-wire Serial Bus. TWI (Slave) Address Register – TWAR Bit 7 6 5 4 3 2 1 0 TWA6 TWA5 TWA4 TWA3 TWA2 TWA1 TWA0 TWGCE TWAR 183 2502K–AVR–10/06
Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 1 1 1 1 1 1 1 0 The TWAR should be loaded with the 7-bit slave address (in the seven most significant bits of TWAR) to which the TWI will respond when programmed as a Slave Transmitter or Receiver, and not needed in the Master modes. In multimaster systems, TWAR must be set in masters which can be addressed as slaves by other masters. The LSB of TWAR is used to enable recognition of the general call address (0x00). There is an associated address comparator that looks for the slave address (or general call address if enabled) in the received serial address. If a match is found, an interrupt request is generated. (cid:129) Bits 7..1 – TWA: TWI (Slave) Address Register These seven bits constitute the slave address of the TWI unit. (cid:129) Bit 0 – TWGCE: TWI General Call Recognition Enable Bit If set, this bit enables the recognition of a General Call given over the Two-wire Serial Bus. ATmega8535(L) 184 2502K–AVR–10/06
ATmega8535(L) Using the TWI The AVR TWI is byte-oriented and interrupt based. Interrupts are issued after all bus events, like reception of a byte or transmission of a START condition. Because the TWI is interrupt-based, the application software is free to carry on other operations during a TWI byte transfer. Note that the TWI Interrupt Enable (TWIE) bit in TWCR together with the Global Interrupt Enable bit in SREG allow the application to decide whether or not assertion of the TWINT Flag should generate an interrupt request. If the TWIE bit is cleared, the application must poll the TWINT Flag in order to detect actions on the TWI bus. When the TWINT Flag is asserted, the TWI has finished an operation and awaits appli- cation response. In this case, the TWI Status Register (TWSR) contains a value indicating the current state of the TWI bus. The application software can then decide how the TWI should behave in the next TWI bus cycle by manipulating the TWCR and TWDR Registers. Figure 85 is a simple example of how the application can interface to the TWI hardware. In this example, a Master wishes to transmit a single data byte to a Slave. This descrip- tion is quite abstract, a more detailed explanation follows later in this section. A simple code example implementing the desired behavior is also presented. Figure 85. Interfacing the Application to the TWI in a Typical Transmission 1. Application writes 3. Check TWSR to see if START was 5. Check TWSR to see if SLA+W was 7. Check TWSR to see if data was sent on to TWCR to initiate sent. Application loads SLA+W into sent and ACK received. Application and ACK received. Application loads ation transmission of TWDR, and loads appropriate control loads data into TWDR, and loads appropriate control signals to send plicActi START signals into TWCR, making sure that appropriate control signals into TWCR, STOP into TWCR, making sure that Ap TWINT is written to one, and TWSTA is making sure that TWINT is TWINT is written to one. written to zero. wwritten to one. TWI bus START SLA+W A Data A STOP Indicates TWIHardwareAction SSTtaAt2Ru.sT T cWcoodInNedT iitn isodenict .saetenst SStaLt4uA.s +T rcWeWoc dIesNeievT nein tds,d eAictC.aKtes daSttaa ts6ue.s nT ctW,o AdINCeT Kin srdeeictc.aetievesd TWINT set 1. The first step in a TWI transmission is to transmit a START condition. This is done by writing a specific value into TWCR, instructing the TWI hardware to transmit a START condition. Which value to write is described later on. However, it is important that the TWINT bit is set in the value written. Writing a one to TWINT clears the flag. The TWI will not start any operation as long as the TWINT bit in TWCR is set. Immediately after the application has cleared TWINT, the TWI will initiate transmission of the START condition. 2. When the START condition has been transmitted, the TWINT Flag in TWCR is set, and TWSR is updated with a status code indicating that the START condition has successfully been sent. 3. The application software should now examine the value of TWSR, to make sure that the START condition was successfully transmitted. If TWSR indicates other- wise, the application software might take some special action, like calling an error routine. Assuming that the status code is as expected, the application must 185 2502K–AVR–10/06
load SLA+W into TWDR. Remember that TWDR is used both for address and data. After TWDR has been loaded with the desired SLA+W, a specific value must be written to TWCR, instructing the TWI hardware to transmit the SLA+W present in TWDR. Which value to write is described later on. However, it is important that the TWINT bit is set in the value written. Writing a one to TWINT clears the flag. The TWI will not start any operation as long as the TWINT bit in TWCR is set. Immediately after the application has cleared TWINT, the TWI will initiate transmission of the address packet. 4. When the address packet has been transmitted, the TWINT Flag in TWCR is set, and TWSR is updated with a status code indicating that the address packet has successfully been sent. The status code will also reflect whether a Slave acknowledged the packet or not. 5. The application software should now examine the value of TWSR, to make sure that the address packet was successfully transmitted, and that the value of the ACK bit was as expected. If TWSR indicates otherwise, the application software might take some special action, like calling an error routine. Assuming that the status code is as expected, the application must load a data packet into TWDR. Subsequently, a specific value must be written to TWCR, instructing the TWI hardware to transmit the data packet present in TWDR. The value which to write is described later on. However, it is important that the TWINT bit is set in the value written. Writing a one to TWINT clears the flag. The TWI will not start any operation as long as the TWINT bit in TWCR is set. Immediately after the appli- cation has cleared TWINT, the TWI will initiate transmission of the data packet. 6. When the data packet has been transmitted, the TWINT Flag in TWCR is set, and TWSR is updated with a status code indicating that the data packet has suc- cessfully been sent. The status code will also reflect whether a Slave acknowledged the packet or not. 7. The application software should now examine the value of TWSR, to make sure that the data packet was successfully transmitted, and that the value of the ACK bit was as expected. If TWSR indicates otherwise, the application software might take some special action, like calling an error routine. Assuming that the status code is as expected, the application must write a specific value to TWCR, instructing the TWI hardware to transmit a STOP condition. Which value to write is described later on. However, it is important that the TWINT bit is set in the value written. Writing a one to TWINT clears the flag. The TWI will not start any operation as long as the TWINT bit in TWCR is set. Immediately after the appli- cation has cleared TWINT, the TWI will initiate transmission of the STOP condition. Note that TWINT is NOT set after a STOP condition has been sent. Even though this example is simple, it shows the principles involved in all TWI transmis- sions. These can be summarized as follows: (cid:129) When the TWI has finished an operation and expects application response, the TWINT Flag is set. The SCL line is pulled low until TWINT is cleared. (cid:129) When the TWINT Flag is set, the user must update all TWI Registers with the value relevant for the next TWI bus cycle. As an example, TWDR must be loaded with the value to be transmitted in the next bus cycle. (cid:129) After all TWI Register updates and other pending application software tasks have been completed, TWCR is written. When writing TWCR, the TWINT bit should be set. Writing a one to TWINT clears the flag. The TWI will then commence executing whatever operation was specified by the TWCR setting. ATmega8535(L) 186 2502K–AVR–10/06
ATmega8535(L) In the following an assembly and C implementation of the example is given. Note that the code below assumes that several definitions have been made, for example by using include-files. Assembly Code Example C Example Comments 1 ldi r16, (1<<TWINT)|(1<<TWSTA)| TWCR = (1<<TWINT)|(1<<TWSTA)| Send START condition. (1<<TWEN) (1<<TWEN) out TWCR, r16 2 wait1: while (!(TWCR & (1<<TWINT))) Wait for TWINT Flag set. This in r16,TWCR ; indicates that the START condition has been transmitted. sbrs r16,TWINT rjmp wait1 3 in r16,TWSR if ((TWSR & 0xF8) != START) Check value of TWI Status andi r16, 0xF8 ERROR(); Register. Mask prescaler bits. If status different from START go to cpi r16, START ERROR. brne ERROR ldi r16, SLA_W TWDR = SLA_W; Load SLA_W into TWDR Register. out TWDR, r16 TWCR = (1<<TWINT) | (1<<TWEN); Clear TWINT bit in TWCR to start transmission of address. ldi r16, (1<<TWINT) | (1<<TWEN) out TWCR, r16 4 wait2: while (!(TWCR & (1<<TWINT))) Wait for TWINT Flag set. This in r16,TWCR ; indicates that the SLA+W has been transmitted, and ACK/NACK has sbrs r16,TWINT been received. rjmp wait2 5 in r16,TWSR if ((TWSR & 0xF8) != MT_SLA_ACK) Check value of TWI Status andi r16, 0xF8 ERROR(); Register. Mask prescaler bits. If status different from MT_SLA_ACK cpi r16, MT_SLA_ACK go to ERROR. brne ERROR ldi r16, DATA TWDR = DATA; Load DATA into TWDR Register. out TWDR, r16 TWCR = (1<<TWINT) | (1<<TWEN); Clear TWINT bit in TWCR to start transmission of address. ldi r16, (1<<TWINT) | (1<<TWEN) out TWCR, r16 6 wait3: while (!(TWCR & (1<<TWINT))) Wait for TWINT Flag set. This in r16,TWCR ; indicates that the DATA has been transmitted, and ACK/NACK has sbrs r16,TWINT been received. rjmp wait3 7 in r16,TWSR if ((TWSR & 0xF8) != MT_DATA_ACK) Check value of TWI Status andi r16, 0xF8 ERROR(); Register. Mask prescaler bits. If status different from cpi r16, MT_DATA_ACK MT_DATA_ACK go to ERROR. brne ERROR ldi r16, (1<<TWINT)|(1<<TWEN)| TWCR = (1<<TWINT)|(1<<TWEN)| Transmit STOP condition. (1<<TWSTO) (1<<TWSTO); out TWCR, r16 187 2502K–AVR–10/06
Transmission Modes The TWI can operate in one of four major modes. These are named Master Transmitter (MT), Master Receiver (MR), Slave Transmitter (ST), and Slave Receiver (SR). Several of these modes can be used in the same application. As an example, the TWI can use MT mode to write data into a TWI EEPROM, MR mode to read the data back from the EEPROM. If other masters are present in the system, some of these might transmit data to the TWI, and then SR mode would be used. It is the application software that decides which modes are legal. The following sections describe each of these modes. Possible status codes are described along with figures detailing data transmission in each of the modes. These fig- ures contain the following abbreviations: S: START condition Rs: REPEATED START condition R: Read bit (high level at SDA) W: Write bit (low level at SDA) A: Acknowledge bit (low level at SDA) A: Not acknowledge bit (high level at SDA) Data: 8-bit data byte P: STOP condition SLA: Slave Address In Figure 87 to Figure 93, circles are used to indicate that the TWINT Flag is set. The numbers in the circles show the status code held in TWSR, with the prescaler bits masked to zero. At these points, actions must be taken by the application to continue or complete the TWI transfer. The TWI transfer is suspended until the TWINT Flag is cleared by software. When the TWINT Flag is set, the status code in TWSR is used to determine the appro- priate software action. For each status code, the required software action and details of the following serial transfer are given in Table 75 to Table 78. Note that the prescaler bits are masked to zero in these tables. ATmega8535(L) 188 2502K–AVR–10/06
ATmega8535(L) Master Transmitter Mode In the Master Transmitter mode, a number of data bytes are transmitted to a Slave Receiver (see Figure 86). In order to enter a Master mode, a START condition must be transmitted. The format of the following address packet determines whether Master Transmitter or Master Receiver mode is to be entered. If SLA+W is transmitted, MT mode is entered, if SLA+R is transmitted, MR mode is entered. All the status codes mentioned in this section assume that the prescaler bits are zero or are masked to zero. Figure 86. Data Transfer in Master Transmitter Mode V CC Device 1 Device 2 Device 3 Device n MASTER SLAVE ........ R1 R2 TRANSMITTER RECEIVER SDA SCL A START condition is sent by writing the following value to TWCR: TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE Value 1 X 1 0 X 1 0 X TWEN must be set to enable the Two-wire Serial Interface, TWSTA must be written to one to transmit a START condition and TWINT must be written to one to clear the TWINT Flag. The TWI will then test the Two-wire Serial Bus and generate a START condition as soon as the bus becomes free. After a START condition has been transmit- ted, the TWINT Flag is set by hardware, and the status code in TWSR will be 0x08 (see Table 75). In order to enter MT mode, SLA+W must be transmitted. This is done by writ- ing SLA+W to TWDR. Thereafter the TWINT bit should be cleared (by writing it to one) to continue the transfer. This is accomplished by writing the following value to TWCR: TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE Value 1 X 0 0 X 1 0 X When SLA+W have been transmitted and an acknowledgement bit has been received, TWINT is set again and a number of status codes in TWSR are possible. Possible sta- tus codes in Master mode are 0x18, 0x20, or 0x38. The appropriate action to be taken for each of these status codes is detailed in Table 75. When SLA+W has been successfully transmitted, a data packet should be transmitted. This is done by writing the data byte to TWDR. TWDR must only be written when TWINT is high. If not, the access will be discarded, and the Write Collision bit (TWWC) will be set in the TWCR Register. After updating TWDR, the TWINT bit should be cleared (by writing it to one) to continue the transfer. This is accomplished by writing the following value to TWCR: TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE Value 1 X 0 0 X 1 0 X 189 2502K–AVR–10/06
This scheme is repeated until the last byte has been sent and the transfer is ended by generating a STOP condition or a repeated START condition. A STOP condition is gen- erated by writing the following value to TWCR: TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE Value 1 X 0 1 X 1 0 X A REPEATED START condition is generated by writing the following value to TWCR: TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE Value 1 X 1 0 X 1 0 X After a repeated START condition (state 0x10) the Two-wire Serial Interface can access the same Slave again, or a new Slave without transmitting a STOP condition. Repeated START enables the Master to switch between Slaves, Master Transmitter mode and Master Receiver mode without losing control of the bus.. Table 75. Status Codes for Master Transmitter Mode Status Code Application Software Response (TWSR) Status of the Two-wire Serial To TWCR Parree s0caler Bits Bfaucse aHnadr dTwwaor-ewire Serial Inter- To/from TWDR STA STO TWINT TWEA Next Action Taken by TWI Hardware 0x08 A START condition has been Load SLA+W 0 0 1 X SLA+W will be transmitted; transmitted ACK or NOT ACK will be received 0x10 A repeated START condition Load SLA+W or 0 0 1 X SLA+W will be transmitted; has been transmitted ACK or NOT ACK will be received Load SLA+R 0 0 1 X SLA+R will be transmitted; Logic will switch to Master Receiver mode 0x18 SLA+W has been transmitted; Load data byte or 0 0 1 X Data byte will be transmitted and ACK or NOT ACK will ACK has been received be received No TWDR action or 1 0 1 X Repeated START will be transmitted No TWDR action or 0 1 1 X STOP condition will be transmitted and TWSTO Flag will be reset No TWDR action 1 1 1 X STOP condition followed by a START condition will be transmitted and TWSTO Flag will be reset 0x20 SLA+W has been transmitted; Load data byte or 0 0 1 X Data byte will be transmitted and ACK or NOT ACK will NOT ACK has been received be received No TWDR action or 1 0 1 X Repeated START will be transmitted No TWDR action or 0 1 1 X STOP condition will be transmitted and TWSTO Flag will be reset No TWDR action 1 1 1 X STOP condition followed by a START condition will be transmitted and TWSTO Flag will be reset 0x28 Data byte has been transmitted; Load data byte or 0 0 1 X Data byte will be transmitted and ACK or NOT ACK will ACK has been received be received No TWDR action or 1 0 1 X Repeated START will be transmitted No TWDR action or 0 1 1 X STOP condition will be transmitted and TWSTO Flag will be reset No TWDR action 1 1 1 X STOP condition followed by a START condition will be transmitted and TWSTO Flag will be reset 0x30 Data byte has been transmitted; Load data byte or 0 0 1 X Data byte will be transmitted and ACK or NOT ACK will NOT ACK has been received be received No TWDR action or 1 0 1 X Repeated START will be transmitted No TWDR action or 0 1 1 X STOP condition will be transmitted and TWSTO Flag will be reset No TWDR action 1 1 1 X STOP condition followed by a START condition will be transmitted and TWSTO Flag will be reset 0x38 Arbitration lost in SLA+W or data No TWDR action or 0 0 1 X Two-wire Serial Bus will be released and not addressed bytes Slave mode entered No TWDR action 1 0 1 X A START condition will be transmitted when the bus be- comes free ATmega8535(L) 190 2502K–AVR–10/06
ATmega8535(L) Figure 87. Formats and States in the Master Transmitter Mode MT Successfull transmission S SLA W A DATA A P to a slave receiver $08 $18 $28 Next transfer started with a RS SLA W repeated start condition $10 Not acknowledge R received after the A P slave address $20 MR Not acknowledge received after a data A P byte $30 Aadrbdirterastsio onr ldoastt ain b syltaeve A or A Otchoenrt imnuaesster A or A Otchoenrt imnuaesster $38 $38 Aadrbdirterastsioend laoss ts alanvde A Otchoenrt imnuaesster $68 $78 $B0 To corresponding states in slave mode Any number of data bytes From master to slave DATA A and their associated acknowledge bits From slave to master This number (contained in TWSR) corresponds n to a defined state of the Two-wire Serial Bus. The prescaler bits are zero or masked to zero 191 2502K–AVR–10/06
Master Receiver Mode In the Master Receiver mode, a number of data bytes are received from a Slave Trans- mitter (see Figure 88). In order to enter a Master mode, a START condition must be transmitted. The format of the following address packet determines whether Master Transmitter or Master Receiver mode is to be entered. If SLA+W is transmitted, MT mode is entered, if SLA+R is transmitted, MR mode is entered. All the status codes mentioned in this section assume that the prescaler bits are zero or are masked to zero. Figure 88. Data Transfer in Master Receiver Mode V CC Device 1 Device 2 Device 3 Device n MASTER SLAVE ........ R1 R2 RECEIVER TRANSMITTER SDA SCL A START condition is sent by writing the following value to TWCR: TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE Value 1 X 1 0 X 1 0 X TWEN must be written to one to enable the Two-wire Serial Interface, TWSTA must be written to one to transmit a START condition and TWINT must be set to clear the TWINT Flag. The TWI will then test the Two-wire Serial Bus and generate a START condition as soon as the bus becomes free. After a START condition has been transmitted, the TWINT Flag is set by hardware, and the status code in TWSR will be 0x08 (see Table 75). In order to enter MR mode, SLA+R must be transmitted. This is done by writing SLA+R to TWDR. Thereafter the TWINT bit should be cleared (by writing it to one) to continue the transfer. This is accomplished by writing the following value to TWCR: TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE Value 1 X 0 0 X 1 0 X When SLA+R have been transmitted and an acknowledgement bit has been received, TWINT is set again and a number of status codes in TWSR are possible. Possible sta- tus codes in Master mode are 0x38, 0x40, or 0x48. The appropriate action to be taken for each of these status codes is detailed in Table 76. Received data can be read from the TWDR Register when the TWINT Flag is set high by hardware. This scheme is repeated until the last byte has been received. After the last byte has been received, the MR should inform the ST by sending a NACK after the last received data byte. The transfer is ended by generating a STOP condition or a repeated START condition. A STOP condition is generated by writing the following value to TWCR: TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE Value 1 X 0 1 X 1 0 X ATmega8535(L) 192 2502K–AVR–10/06
ATmega8535(L) A REPEATED START condition is generated by writing the following value to TWCR: TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE Value 1 X 1 0 X 1 0 X After a repeated START condition (state 0x10) the Two-wire Serial Interface can access the same Slave again, or a new Slave without transmitting a STOP condition. Repeated START enables the Master to switch between Slaves, Master Transmitter mode and Master Receiver mode without losing control over the bus. Table 76. Status Codes for Master Receiver Mode Status Code Application Software Response (TWSR) Status of the Two-wire Serial To TWCR Parree s0caler Bits Bfaucse aHnadr dTwwaor-ewire Serial Inter- To/from TWDR STA STO TWINT TWEA Next Action Taken by TWI Hardware 0x08 A START condition has been Load SLA+R 0 0 1 X SLA+R will be transmitted transmitted ACK or NOT ACK will be received 0x10 A repeated START condition Load SLA+R or 0 0 1 X SLA+R will be transmitted has been transmitted ACK or NOT ACK will be received Load SLA+W 0 0 1 X SLA+W will be transmitted Logic will switch to Master Transmitter mode 0x38 Arbitration lost in SLA+R or NOT No TWDR action or 0 0 1 X Two-wire Serial Bus will be released and not addressed ACK bit Slave mode will be entered No TWDR action 1 0 1 X A START condition will be transmitted when the bus becomes free 0x40 SLA+R has been transmitted; No TWDR action or 0 0 1 0 Data byte will be received and NOT ACK will be ACK has been received returned No TWDR action 0 0 1 1 Data byte will be received and ACK will be returned 0x48 SLA+R has been transmitted; No TWDR action or 1 0 1 X Repeated START will be transmitted NOT ACK has been received No TWDR action or 0 1 1 X STOP condition will be transmitted and TWSTO Flag will be reset No TWDR action 1 1 1 X STOP condition followed by a START condition will be transmitted and TWSTO Flag will be reset 0x50 Data byte has been received; Read data byte or 0 0 1 0 Data byte will be received and NOT ACK will be ACK has been returned returned Read data byte 0 0 1 1 Data byte will be received and ACK will be returned 0x58 Data byte has been received; Read data byte or 1 0 1 X Repeated START will be transmitted NOT ACK has been returned Read data byte or 0 1 1 X STOP condition will be transmitted and TWSTO flag will be reset Read data byte 1 1 1 X STOP condition followed by a START condition will be transmitted and TWSTO Flag Will be reset 193 2502K–AVR–10/06
Figure 89. Formats and States in the Master Receiver Mode MR Successfull reception S SLA R A DATA A DATA A P from a slave receiver $08 $40 $50 $58 Next transfer started with a RS SLA R repeated start condition $10 Not acknowledge W received after the A P slave address $48 MT Aadrbdirterastsio onr ldoastt ain b syltaeve A or A Otchoenrt imnuaesster A Otchoenrt imnuaesster $38 $38 Aadrbdirterastsioend laoss ts alanvde A Otchoenrt imnuaesster $68 $78 $B0 Tsota cteosr riens sploanved inmgode Any number of data bytes From master to slave DATA A and their associated acknowledge bits From slave to master This number (contained in TWSR) corresponds n to a defined state of the Two-wire Serial Bus. The prescaler bits are zero or masked to zero Slave Receiver Mode In the Slave Receiver mode, a number of data bytes are received from a Master Trans- mitter (see Figure 90). All the status codes mentioned in this section assume that the prescaler bits are zero or are masked to zero. Figure 90. Data Transfer in Slave Receiver Mode V CC Device 1 Device 2 Device 3 Device n ........ R1 R2 SLAVE MASTER RECEIVER TRANSMITTER SDA SCL ATmega8535(L) 194 2502K–AVR–10/06
ATmega8535(L) To initiate the Slave Receiver mode, TWAR and TWCR must be initialized as follows: TWAR TWA6 TWA5 TWA4 TWA3 TWA2 TWA1 TWA0 TWGCE Value Device’s Own Slave Address The upper seven bits are the address to which the Two-wire Serial Interface will respond when addressed by a Master. If the LSB is set, the TWI will respond to the general call address (0x00), otherwise it will ignore the general call address. TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE Value 0 1 0 0 0 1 0 X TWEN must be written to one to enable the TWI. The TWEA bit must be written to one to enable the acknowledgement of the device’s own slave address or the general call address. TWSTA and TWSTO must be written to zero. When TWAR and TWCR have been initialized, the TWI waits until it is addressed by its own slave address (or the general call address if enabled) followed by the data direction bit. If the direction bit is “0” (write), the TWI will operate in SR mode, otherwise ST mode is entered. After its own slave address and the write bit have been received, the TWINT Flag is set and a valid status code can be read from TWSR. The status code is used to determine the appropriate software action. The appropriate action to be taken for each status code is detailed in Table 77. The Slave Receiver mode may also be entered if arbitration is lost while the TWI is in the Master mode (see states 0x68 and 0x78). If the TWEA bit is reset during a transfer, the TWI will return a “Not Acknowledge” (“1”) to SDA after the next received data byte. This can be used to indicate that the Slave is not able to receive any more bytes. While TWEA is zero, the TWI does not acknowledge its own slave address. However, the Two-wire Serial Bus is still monitored and address recognition may resume at any time by setting TWEA. This implies that the TWEA bit may be used to temporarily isolate the TWI from the Two-wire Serial Bus. In all sleep modes other than Idle mode, the clock system to the TWI is turned off. If the TWEA bit is set, the interface can still acknowledge its own slave address or the general call address by using the Two-wire Serial Bus clock as a clock source. The part will then wake up from sleep and the TWI will hold the SCL clock low during the wake up and until the TWINT Flag is cleared (by writing it to one). Further data reception will be car- ried out as normal, with the AVR clocks running as normal. Observe that if the AVR is set up with a long start-up time, the SCL line may be held low for a long time, blocking other data transmissions. Note that the Two-wire Serial Interface Data Register – TWDR – does not reflect the last byte present on the bus when waking up from these sleep modes. 195 2502K–AVR–10/06
Table 77. Status Codes for Slave Receiver Mode Status Code Application Software Response (TWSR) To TWCR Prescaler Bits Status of the Two-wire Serial Bus are 0 and Two-wire Serial Interface To/from TWDR STA STO TWINT TWEA Next Action Taken by TWI Hardware Hardware 0x60 Own SLA+W has been received; No TWDR action or X 0 1 0 Data byte will be received and NOT ACK will be ACK has been returned returned No TWDR action X 0 1 1 Data byte will be received and ACK will be returned 0x68 Arbitration lost in SLA+R/W as No TWDR action or X 0 1 0 Data byte will be received and NOT ACK will be Master; own SLA+W has been returned received; ACK has been returned No TWDR action X 0 1 1 Data byte will be received and ACK will be returned 0x70 General call address has been No TWDR action or X 0 1 0 Data byte will be received and NOT ACK will be received; ACK has been returned returned No TWDR action X 0 1 1 Data byte will be received and ACK will be returned 0x78 Arbitration lost in SLA+R/W as No TWDR action or X 0 1 0 Data byte will be received and NOT ACK will be Master; General call address has returned been received; ACK has been No TWDR action X 0 1 1 Data byte will be received and ACK will be returned returned 0x80 Previously addressed with own Read data byte or X 0 1 0 Data byte will be received and NOT ACK will be SLA+W; data has been received; returned ACK has been returned Read data byte X 0 1 1 Data byte will be received and ACK will be returned 0x88 Previously addressed with own Read data byte or 0 0 1 0 Switched to the not addressed Slave mode; SLA+W; data has been received; no recognition of own SLA or GCA NOT ACK has been returned Read data byte or 0 0 1 1 Switched to the not addressed Slave mode; own SLA will be recognized; GCA will be recognized if TWGCE = “1” Read data byte or 1 0 1 0 Switched to the not addressed Slave mode; no recognition of own SLA or GCA; a START condition will be transmitted when the bus becomes free Read data byte 1 0 1 1 Switched to the not addressed Slave mode; own SLA will be recognized; GCA will be recognized if TWGCE = “1”; a START condition will be transmitted when the bus becomes free 0x90 Previously addressed with Read data byte or X 0 1 0 Data byte will be received and NOT ACK will be general call; data has been re- returned ceived; ACK has been returned Read data byte X 0 1 1 Data byte will be received and ACK will be returned 0x98 Previously addressed with Read data byte or 0 0 1 0 Switched to the not addressed Slave mode; general call; data has been no recognition of own SLA or GCA received; NOT ACK has been Read data byte or 0 0 1 1 Switched to the not addressed Slave mode; returned own SLA will be recognized; GCA will be recognized if TWGCE = “1” Read data byte or 1 0 1 0 Switched to the not addressed Slave mode; no recognition of own SLA or GCA; a START condition will be transmitted when the bus becomes free Read data byte 1 0 1 1 Switched to the not addressed Slave mode; own SLA will be recognized; GCA will be recognized if TWGCE = “1”; a START condition will be transmitted when the bus becomes free 0xA0 A STOP condition or repeated No action 0 0 1 0 Switched to the not addressed Slave mode; START condition has been no recognition of own SLA or GCA received while still addressed as 0 0 1 1 Switched to the not addressed Slave mode; Slave own SLA will be recognized; GCA will be recognized if TWGCE = “1” 1 0 1 0 Switched to the not addressed Slave mode; no recognition of own SLA or GCA; a START condition will be transmitted when the bus becomes free 1 0 1 1 Switched to the not addressed Slave mode; own SLA will be recognized; GCA will be recognized if TWGCE = “1”; a START condition will be transmitted when the bus becomes free ATmega8535(L) 196 2502K–AVR–10/06
ATmega8535(L) Figure 91. Formats and States in the Slave Receiver Mode Reception of the own slave address and one or S SLA W A DATA A DATA A P or S more data bytes. All are acknowledged $60 $80 $80 $A0 Last data byte received is not acknowledged A P or S $88 Arbitration lost as master and addressed as slave A $68 Reception of the general call address and one or more data General Call A DATA A DATA A P or S bytes $70 $90 $90 $A0 Last data byte received is not acknowledged A P or S $98 Arbitration lost as master and addressed as slave by general call A $78 Any number of data bytes From master to slave DATA A and their associated acknowledge bits From slave to master This number (contained in TWSR) corresponds n to a defined state of the Two-wire Serial Bus. The prescaler bits are zero or masked to zero 197 2502K–AVR–10/06
Slave Transmitter Mode In the Slave Transmitter mode, a number of data bytes are transmitted to a Master Receiver (see Figure 92). All the status codes mentioned in this section assume that the prescaler bits are zero or are masked to zero. Figure 92. Data Transfer in Slave Transmitter Mode V CC Device 1 Device 2 Device 3 Device n ........ R1 R2 SLAVE MASTER TRANSMITTER RECEIVER SDA SCL To initiate the Slave Transmitter mode, TWAR and TWCR must be initialized as follows: TWAR TWA6 TWA5 TWA4 TWA3 TWA2 TWA1 TWA0 TWGCE Value Device’s Own Slave Address The upper seven bits are the address to which the Two-wire Serial Interface will respond when addressed by a Master. If the LSB is set, the TWI will respond to the general call address (0x00), otherwise it will ignore the general call address. TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE Value 0 1 0 0 0 1 0 X TWEN must be written to one to enable the TWI. The TWEA bit must be written to one to enable the acknowledgement of the device’s own slave address or the general call address. TWSTA and TWSTO must be written to zero. When TWAR and TWCR have been initialized, the TWI waits until it is addressed by its own slave address (or the general call address if enabled) followed by the data direction bit. If the direction bit is “1” (read), the TWI will operate in ST mode, otherwise SR mode is entered. After its own slave address and the write bit have been received, the TWINT Flag is set and a valid status code can be read from TWSR. The status code is used to determine the appropriate software action. The appropriate action to be taken for each status code is detailed in Table 78. The Slave Transmitter mode may also be entered if arbitration is lost while the TWI is in the Master mode (see state 0xB0). If the TWEA bit is written to zero during a transfer, the TWI will transmit the last byte of the transfer. State 0xC0 or state 0xC8 will be entered, depending on whether the Master Receiver transmits a NACK or ACK after the final byte. The TWI is switched to the not addressed Slave mode, and will ignore the Master if it continues the transfer. Thus the Master Receiver receives all “1” as serial data. State 0xC8 is entered if the Master demands additional data bytes (by transmitting ACK), even though the Slave has trans- mitted the last byte (TWEA zero and expecting NACK from the Master). While TWEA is zero, the TWI does not respond to its own slave address. However, the Two-wire Serial Bus is still monitored and address recognition may resume at any time ATmega8535(L) 198 2502K–AVR–10/06
ATmega8535(L) by setting TWEA. This implies that the TWEA bit may be used to temporarily isolate the TWI from the Two-wire Serial Bus. In all sleep modes other than Idle mode, the clock system to the TWI is turned off. If the TWEA bit is set, the interface can still acknowledge its own slave address or the general call address by using the Two-wire Serial Bus clock as a clock source. The part will then wake up from sleep and the TWI will hold the SCL clock will low during the wake up and until the TWINT Flag is cleared (by writing it to one). Further data transmission will be carried out as normal, with the AVR clocks running as normal. Observe that if the AVR is set up with a long start-up time, the SCL line may be held low for a long time, blocking other data transmissions. Note that the Two-wire Serial Interface Data Register – TWDR – does not reflect the last byte present on the bus when waking up from these sleep modes. Table 78. Status Codes for Slave Transmitter Mode Status Code Application Software Response (TWSR) Status of the Two-wire Serial Bus To TWCR Prescaler Bits and Two-wire Serial Interface are 0 Hardware To/from TWDR STA STO TWINT TWEA Next Action Taken by TWI Hardware 0xA8 Own SLA+R has been received; Load data byte or X 0 1 0 Last data byte will be transmitted and NOT ACK should ACK has been returned be received Load data byte X 0 1 1 Data byte will be transmitted and ACK should be re- ceived 0xB0 Arbitration lost in SLA+R/W as Load data byte or X 0 1 0 Last data byte will be transmitted and NOT ACK should Master; own SLA+R has been be received received; ACK has been returned Load data byte X 0 1 1 Data byte will be transmitted and ACK should be re- ceived 0xB8 Data byte in TWDR has been Load data byte or X 0 1 0 Last data byte will be transmitted and NOT ACK should transmitted; ACK has been be received received Load data byte X 0 1 1 Data byte will be transmitted and ACK should be re- ceived 0xC0 Data byte in TWDR has been No TWDR action or 0 0 1 0 Switched to the not addressed Slave mode; transmitted; NOT ACK has been no recognition of own SLA or GCA received No TWDR action or 0 0 1 1 Switched to the not addressed Slave mode; own SLA will be recognized; GCA will be recognized if TWGCE = “1” No TWDR action or 1 0 1 0 Switched to the not addressed Slave mode; no recognition of own SLA or GCA; a START condition will be transmitted when the bus becomes free No TWDR action 1 0 1 1 Switched to the not addressed Slave mode; own SLA will be recognized; GCA will be recognized if TWGCE = “1”; a START condition will be transmitted when the bus becomes free 0xC8 Last data byte in TWDR has been No TWDR action or 0 0 1 0 Switched to the not addressed Slave mode; transmitted (TWEA = “0”); ACK no recognition of own SLA or GCA has been received No TWDR action or 0 0 1 1 Switched to the not addressed Slave mode; own SLA will be recognized; GCA will be recognized if TWGCE = “1” No TWDR action or 1 0 1 0 Switched to the not addressed Slave mode; no recognition of own SLA or GCA; a START condition will be transmitted when the bus becomes free No TWDR action 1 0 1 1 Switched to the not addressed Slave mode; own SLA will be recognized; GCA will be recognized if TWGCE = “1”; a START condition will be transmitted when the bus becomes free 199 2502K–AVR–10/06
Figure 93. Formats and States in the Slave Transmitter Mode Reception of the own slave address and one or S SLA R A DATA A DATA A P or S more data bytes $A8 $B8 $C0 Arbitration lost as master and addressed as slave A $B0 Last data byte transmitted. Switched to not addressed A All 1's P or S slave (TWEA = '0') $C8 Any number of data bytes From master to slave DATA A and their associated acknowledge bits From slave to master This number (contained in TWSR) corresponds n to a defined state of the Two-wire Serial Bus. The prescaler bits are zero or masked to zero Miscellaneous States There are two status codes that do not correspond to a defined TWI state, see Table 79. Status 0xF8 indicates that no relevant information is available because the TWINT Flag is not set. This occurs between other states, and when the TWI is not involved in a serial transfer. Status 0x00 indicates that a bus error has occurred during a Two-wire Serial Bus trans- fer. A bus error occurs when a START or STOP condition occurs at an illegal position in the format frame. Examples of such illegal positions are during the serial transfer of an address byte, a data byte, or an acknowledge bit. When a bus error occurs, TWINT is set. To recover from a bus error, the TWSTO Flag must set and TWINT must be cleared by writing a logic one to it. This causes the TWI to enter the not addressed Slave mode and to clear the TWSTO Flag (no other bits in TWCR are affected). The SDA and SCL lines are released, and no STOP condition is transmitted. Table 79. Miscellaneous States Status Code Application Software Response (TWSR) Status of the Two-wire Serial To TWCR Next Action Taken by TWI Hardware Parree s0caler Bits Bfaucse aHnadr dTwwaor-ewire Serial Inter- To/from TWDR STA STO TWINT TWEA 0xF8 No relevant state information No TWDR action No TWCR Action Wait or proceed current transfer available; TWINT = “0” 0x00 Bus error due to an illegal No TWDR action 0 1 1 X Only the internal hardware is affected, no STOP condi- START or STOP condition tion is sent on the bus. In all cases, the bus is released and TWSTO is cleared. ATmega8535(L) 200 2502K–AVR–10/06
ATmega8535(L) Combining Several TWI In some cases, several TWI modes must be combined in order to complete the desired Modes action. Consider for example reading data from a serial EEPROM. Typically, such a transfer involves the following steps: 1. The transfer must be initiated. 2. The EEPROM must be instructed what location should be read. 3. The reading must be performed. 4. The transfer must be finished. Note that data is transmitted both from Master to Slave and vice versa. The Master must instruct the Slave what location it wants to read, requiring the use of the MT mode. Sub- sequently, data must be read from the Slave, implying the use of the MR mode. Thus, the transfer direction must be changed. The Master must keep control of the bus during all these steps, and the steps should be carried out as an atomical operation. If this prin- ciple is violated in a multimaster system, another Master can alter the data pointer in the EEPROM between steps 2 and 3, and the Master will read the wrong data location. Such a change in transfer direction is accomplished by transmitting a REPEATED START between the transmission of the address byte and reception of the data. After a REPEATED START, the Master keeps ownership of the bus. The following figure shows the flow in this transfer. Figure 94. Combining Several TWI Modes to Access a Serial EEPROM Master Transmitter Master Receiver S SLA+W A ADDRESS A Rs SLA+R A DATA A P S = START Rs = REPEATED START P = STOP Transmitted from master to slave Transmitted from slave to master Multi-master Systems If Multiple Masters are connected to the same bus, transmissions may be initiated simul- and Arbitration taneously by one or more of them. The TWI standard ensures that such situations are handled in such a way that one of the masters will be allowed to proceed with the trans- fer, and that no data will be lost in the process. An example of an arbitration situation is depicted below, where two masters are trying to transmit data to a Slave Receiver. Figure 95. An Arbitration Example V CC Device 1 Device 2 Device 3 MASTER MASTER SLAVE ........ Device n R1 R2 TRANSMITTER TRANSMITTER RECEIVER SDA SCL 201 2502K–AVR–10/06
Several different scenarios may arise during arbitration, as described below: (cid:129) Two or more masters are performing identical communication with the same Slave. In this case, neither the Slave nor any of the masters will know about the bus contention. (cid:129) Two or more masters are accessing the same Slave with different data or direction bit. In this case, arbitration will occur, either in the READ/WRITE bit or in the data bits. The masters trying to output a one on SDA while another Master outputs a zero will lose the arbitration. Losing masters will switch to not addressed Slave mode or wait until the bus is free and transmit a new START condition, depending on application software action. (cid:129) Two or more masters are accessing different slaves. In this case, arbitration will occur in the SLA bits. Masters trying to output a one on SDA while another Master outputs a zero will lose the arbitration. Masters losing arbitration in SLA will switch to Slave mode to check if they are being addressed by the winning Master. If addressed, they will switch to SR or ST mode, depending on the value of the READ/WRITE bit. If they are not being addressed, they will switch to not addressed Slave mode or wait until the bus is free and transmit a new START condition, depending on application software action. This is summarized in Figure 96. Possible status values are given in circles. Figure 96. Possible Status Codes Caused by Arbitration START SLA Data STOP Arbitration lost in SLA Arbitration lost in Data Own No 38 TWI bus will be released and not addressed slave mode will be entered Address / General Call A START condition will be transmitted when the bus becomes free received Yes Write 68/78 Data byte will be received and NOT ACK will be returned Direction Data byte will be received and ACK will be returned Read Last data byte will be transmitted and NOT ACK should be received B0 Data byte will be transmitted and ACK should be received ATmega8535(L) 202 2502K–AVR–10/06
ATmega8535(L) Analog Comparator The Analog Comparator compares the input values on the positive pin AIN0 and nega- tive pin AIN1. When the voltage on the positive pin AIN0 is higher than the voltage on the negative pin AIN1, the Analog Comparator Output, ACO, is set. The comparator’s output can be set to trigger the Timer/Counter1 Input Capture function. In addition, the comparator can trigger a separate interrupt, exclusive to the Analog Comparator. The user can select Interrupt triggering on comparator output rise, fall or toggle. A block dia- gram of the comparator and its surrounding logic is shown in Figure 97. Figure 97. Analog Comparator Block Diagram(2) BANDGAP REFERENCE ACBG ACME ADEN ADC MULTIPLEXER OUTPUT(1) Notes: 1. See Table 81 on page 205. 2. Refer to Figure 1 on page 2 and Table 26 on page 60 for Analog Comparator pin placement. Special Function IO Register – SFIOR Bit 7 6 5 4 3 2 1 0 ADTS2 ADTS1 ADTS0 – ACME PUD PSR2 PSR10 SFIOR Read/Write R/W R/W R/W R R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 3 – ACME: Analog Comparator Multiplexer Enable When this bit is written logic one and the ADC is switched off (ADEN in ADCSRA is zero), the ADC multiplexer selects the negative input to the Analog Comparator. When this bit is written logic zero, AIN1 is applied to the negative input of the Analog Compar- ator. For a detailed description of this bit, see “Analog Comparator Multiplexed Input” on page 205. Analog Comparator Control and Status Register – ACSR Bit 7 6 5 4 3 2 1 0 ACD ACBG ACO ACI ACIE ACIC ACIS1 ACIS0 ACSR Read/Write R/W R/W R R/W R/W R/W R/W R/W Initial Value 0 0 N/A 0 0 0 0 0 (cid:129) Bit 7 – ACD: Analog Comparator Disable When this bit is written logic one, the power to the Analog Comparator is switched off. This bit can be set at any time to turn off the Analog Comparator. This will reduce power consumption in active and Idle mode. When changing the ACD bit, the Analog Compar- 203 2502K–AVR–10/06
ator Interrupt must be disabled by clearing the ACIE bit in ACSR. Otherwise an interrupt can occur when the bit is changed. (cid:129) Bit 6 – ACBG: Analog Comparator Bandgap Select When this bit is set, a fixed bandgap reference voltage replaces the positive input to the Analog Comparator. When this bit is cleared, AIN0 is applied to the positive input of the Analog Comparator. See “Internal Voltage Reference” on page 41. (cid:129) Bit 5 – ACO: Analog Comparator Output The output of the Analog Comparator is synchronized and then directly connected to ACO. The synchronization introduces a delay of 1 - 2 clock cycles. (cid:129) Bit 4 – ACI: Analog Comparator Interrupt Flag This bit is set by hardware when a comparator output event triggers the interrupt mode defined by ACIS1 and ACIS0. The Analog Comparator Interrupt routine is executed if the ACIE bit is set and the I-bit in SREG is set. ACI is cleared by hardware when execut- ing the corresponding interrupt handling vector. Alternatively, ACI is cleared by writing a logic one to the flag. (cid:129) Bit 3 – ACIE: Analog Comparator Interrupt Enable When the ACIE bit is written logic one and the I-bit in the Status Register is set, the Ana- log Comparator Interrupt is activated. When written logic zero, the interrupt is disabled. (cid:129) Bit 2 – ACIC: Analog Comparator Input Capture Enable When written logic one, this bit enables the Input Capture function in Timer/Counter1 to be triggered by the Analog Comparator. The comparator output is in this case directly connected to the Input Capture front-end logic, making the comparator utilize the noise canceler and edge select features of the Timer/Counter1 Input Capture interrupt. When written logic zero, no connection between the analog comparator and the Input Capture function exists. To make the comparator trigger the Timer/Counter1 Input Capture inter- rupt, the TICIE1 bit in the Timer Interrupt Mask Register (TIMSK) must be set. (cid:129) Bits 1, 0 – ACIS1, ACIS0: Analog Comparator Interrupt Mode Select These bits determine which comparator events that trigger the Analog Comparator Inter- rupt. The different settings are shown in Table 80. Table 80. ACIS1/ACIS0 Settings ACIS1 ACIS0 Interrupt Mode 0 0 Comparator Interrupt on Output Toggle 0 1 Reserved 1 0 Comparator Interrupt on Falling Output Edge 1 1 Comparator Interrupt on Rising Output Edge When changing the ACIS1/ACIS0 bits, the Analog Comparator Interrupt must be dis- abled by clearing its Interrupt Enable bit in the ACSR Register. Otherwise an interrupt can occur when the bits are changed. ATmega8535(L) 204 2502K–AVR–10/06
ATmega8535(L) Analog Comparator It is possible to select any of the ADC7..0 pins to replace the negative input to the Ana- Multiplexed Input log Comparator. The ADC multiplexer is used to select this input, and consequently, the ADC must be switched off to utilize this feature. If the Analog Comparator Multiplexer Enable bit (ACME in SFIOR) is set and the ADC is switched off (ADEN in ADCSRA is zero), MUX2..0 in ADMUX select the input pin to replace the negative input to the Ana- log Comparator, as shown in Table 81. If ACME is cleared or ADEN is set, AIN1 is applied to the negative input to the Analog Comparator. Table 81. Analog Comparator Multiplexed Input ACME ADEN MUX2..0 Analog Comparator Negative Input 0 x xxx AIN1 1 1 xxx AIN1 1 0 000 ADC0 1 0 001 ADC1 1 0 010 ADC2 1 0 011 ADC3 1 0 100 ADC4 1 0 101 ADC5 1 0 110 ADC6 1 0 111 ADC7 205 2502K–AVR–10/06
Analog-to-Digital Converter Features (cid:129) 10-bit Resolution (cid:129) 0.5 LSB Integral Non-linearity (cid:129) ±2 LSB Absolute Accuracy (cid:129) 65 - 260 µs Conversion Time (cid:129) Up to 15 kSPS at Maximum Resolution (cid:129) 8 Multiplexed Single Ended Input Channels (cid:129) 7 Differential Input Channels (cid:129) 2 Differential Input Channels with Optional Gain of 10x and 200x(1) (cid:129) Optional Left Adjustment for ADC Result Readout (cid:129) 0 - V ADC Input Voltage Range CC (cid:129) Selectable 2.56V ADC Reference Voltage (cid:129) Free Running or Single Conversion Mode (cid:129) ADC Start Conversion by Auto Triggering on Interrupt Sources (cid:129) Interrupt on ADC Conversion Complete (cid:129) Sleep Mode Noise Canceler Note: 1. The differential input channel are not tested for devices in PDIP and PLCC Package. This feature is only guaranteed to work for devices in TQFP and QFN/MLF Packages. The ATmega8535 features a 10-bit successive approximation ADC. The ADC is con- nected to an 8-channel Analog Multiplexer which allows eight single-ended voltage inputs constructed from the pins of Port A. The single-ended voltage inputs refer to 0V (GND). The device also supports 16 differential voltage input combinations. Two of the differen- tial inputs (ADC1, ADC0 and ADC3, ADC2) are equipped with a programmable gain stage, providing amplification steps of 0 dB (1x), 20 dB (10x), or 46 dB (200x) on the dif- ferential input voltage before the A/D conversion. Seven differential analog input channels share a common negative terminal (ADC1), while any other ADC input can be selected as the positive input terminal. If 1x or 10x gain is used, 8-bit resolution can be expected. If 200x gain is used, 7-bit resolution can be expected. The ADC contains a Sample and Hold circuit which ensures that the input voltage to the ADC is held at a constant level during conversion. A block diagram of the ADC is shown in Figure 98. The ADC has a separate analog supply voltage pin, AVCC. AVCC must not differ more than ±0.3V from V . See the paragraph “ADC Noise Canceler” on page 214 on how to CC connect this pin. Internal reference voltages of nominally 2.56V or AVCC are provided On-chip. The volt- age reference may be externally decoupled at the AREF pin by a capacitor for better noise performance. ATmega8535(L) 206 2502K–AVR–10/06
ATmega8535(L) Figure 98. Analog-to-Digital Converter Block Schematic ADC CONVERSION COMPLETE IRQ INTERRUPT FLAGS ADTS[2:0] 8-BIT DATA BUS ADIF ADIE 15 0 ADC MULTIPLEXER ADC CTRL. & STATUS ADC DATA REGISTER SELECT (ADMUX) REGISTER (ADCSRA) (ADCH/ADCL) REFS1 REFS0 ADLAR MUX4 MUX3 MUX2 MUX1 MUX0 ADEN ADSC ADATE ADIF ADPS2 ADPS1 ADPS0 TSREIGLEGCETR ADC[9:0] MUX DECODER PRESCALER AVCC CHANNEL SELECTION GAIN SELECTION CONVERSION LOSGTIACRT INTERNAL 2.56V REFERENCE SAMPLE & HOLD COMPARATOR AREF 10-BIT DAC - + GND BANDGAP REFERENCE ADC7 SINGLE ENDED / DIFFERENTIAL SELECTION ADC6 ADC5 INPOPUST. AODUCT PMUUTLTIPLEXER MUX ADC4 ADC3 GAIN AMPLIFIER + ADC2 - ADC1 ADC0 NEG. INPUT MUX Operation The ADC converts an analog input voltage to a 10-bit digital value through successive approximation. The minimum value represents GND and the maximum value represents the voltage on the AREF pin minus 1 LSB. Optionally, AVCC or an internal 2.56V refer- ence voltage may be connected to the AREF pin by writing to the REFSn bits in the ADMUX Register. The internal voltage reference may thus be decoupled by an external capacitor at the AREF pin to improve noise immunity. The analog input channel and differential gain are selected by writing to the MUX bits in ADMUX. Any of the ADC input pins, as well as GND and a fixed bandgap voltage refer- ence, can be selected as single ended inputs to the ADC. A selection of ADC input pins can be selected as positive and negative inputs to the differential gain amplifier. If differential channels are selected, the differential gain stage amplifies the voltage dif- ference between the selected input channel pair by the selected gain factor. This amplified value then becomes the analog input to the ADC. If single ended channels are used, the gain amplifier is bypassed altogether. 207 2502K–AVR–10/06
The ADC is enabled by setting the ADC Enable bit, ADEN in ADCSRA. Voltage refer- ence and input channel selections will not go into effect until ADEN is set. The ADC does not consume power when ADEN is cleared, so it is recommended to switch off the ADC before entering power saving sleep modes. The ADC generates a 10-bit result which is presented in the ADC Data Registers, ADCH and ADCL. By default, the result is presented right adjusted, but can optionally be presented left adjusted by setting the ADLAR bit in ADMUX. If the result is left adjusted and no more than 8-bit precision is required, it is sufficient to read ADCH. Otherwise, ADCL must be read first, then ADCH, to ensure that the content of the data registers belongs to the same conversion. Once ADCL is read, ADC access to data registers is blocked. This means that if ADCL has been read, and a conversion completes before ADCH is read, neither register is updated and the result from the con- version is lost. When ADCH is read, ADC access to the ADCH and ADCL Registers is re-enabled. The ADC has its own interrupt which can be triggered when a conversion completes. When ADC access to the data registers is prohibited between reading of ADCH and ADCL, the interrupt will trigger even if the result is lost. Starting a Conversion A single conversion is started by writing a logical one to the ADC Start Conversion bit, ADSC. This bit stays high as long as the conversion is in progress and will be cleared by hardware when the conversion is completed. If a different data channel is selected while a conversion is in progress, the ADC will finish the current conversion before performing the channel change. Alternatively, a conversion can be triggered automatically by various sources. Auto Trig- gering is enabled by setting the ADC Auto Trigger Enable bit, ADATE in ADCSRA. The trigger source is selected by setting the ADC Trigger Select bits, ADTS in SFIOR (See description of the ADTS bits for a list of the trigger sources). When a positive edge occurs on the selected trigger signal, the ADC prescaler is reset and a conversion is started. This provides a method of starting conversions at fixed intervals. If the trigger signal still is set when the conversion completes, a new conversion will not be started. If another positive edge occurs on the trigger signal during conversion, the edge will be ignored. Note that an interrupt flag will be set even if the specific interrupt is disabled or the global interrupt enable bit in SREG is cleared. A conversion can thus be triggered without causing an interrupt. However, the interrupt flag must be cleared in order to trig- ger a new conversion at the next interrupt event. ATmega8535(L) 208 2502K–AVR–10/06
ATmega8535(L) Figure 99. ADC Auto Trigger Logic ADTS[2:0] PRESCALER START CLK ADC ADIF ADATE SOURCE 1 . CONVERSION . LOGIC . . EDGE DETECTOR SOURCE n ADSC Using the ADC Interrupt Flag as a trigger source makes the ADC start a new conversion as soon as the ongoing conversion has finished. The ADC then operates in Free Run- ning mode, constantly sampling and updating the ADC Data Register. The first conversion must be started by writing a logical one to the ADSC bit in ADCSRA. In this mode the ADC will perform successive conversions independently of whether the ADC Interrupt Flag, ADIF is cleared or not. If Auto Triggering is enabled, single conversions can be started by writing ADSC in ADCSRA to one. ADSC can also be used to determine if a conversion is in progress. The ADSC bit will be read as one during a conversion, independently of how the conver- sion was started. Prescaling and Figure 100. ADC Prescaler Conversion Timing ADEN Reset START 7-BIT ADC PRESCALER CK 8 6 2 4 2 2 4 8 1 3 6 1 K/ K/ K/ K/ K/ K/ K/ C C C C C C C ADPS0 ADPS1 ADPS2 ADC CLOCK SOURCE By default, the successive approximation circuitry requires an input clock frequency between 50 kHz and 200 kHz to get maximum resolution. If a lower resolution than 10bits is needed, the input clock frequency to the ADC can be higher than 200 kHz to get a higher sample rate. 209 2502K–AVR–10/06
The ADC module contains a prescaler, which generates an acceptable ADC clock fre- quency from any CPU frequency above 100 kHz. The prescaling is set by the ADPS bits in ADCSRA. The prescaler starts counting from the moment the ADC is switched on by setting the ADEN bit in ADCSRA. The prescaler keeps running for as long as the ADEN bit is set, and is continuously reset when ADEN is low. When initiating a single ended conversion by setting the ADSC bit in ADCSRA, the con- version starts at the following rising edge of the ADC clock cycle. See “Differential Gain Channels” on page 212 for details on differential conversion timing. A normal conversion takes 13 ADC clock cycles. The first conversion after the ADC is switched on (ADEN in ADCSRA is set) takes 25 ADC clock cycles in order to initialize the analog circuitry. The actual sample-and-hold takes place 1.5 ADC clock cycles after the start of a normal conversion and 13.5 ADC clock cycles after the start of an first conversion. When a con- version is complete, the result is written to the ADC Data Registers, and ADIF is set. In Single Conversion mode, ADSC is cleared simultaneously. The software may then set ADSC again, and a new conversion will be initiated on the first rising ADC clock edge. When Auto Triggering is used, the prescaler is reset when the trigger event occurs. This assures a fixed delay from the trigger event to the start of conversion. In this mode, the sample-and-hold takes place two ADC clock cycles after the rising edge on the trigger source signal. Three additional CPU clock cycles are used for synchronization logic. In Free Running mode, a new conversion will be started immediately after the conver- sion completes, while ADSC remains high. For a summary of conversion times, see Table 82. Figure 101. ADC Timing Diagram, First Conversion (Single Conversion Mode) Next First Conversion Conversion Cycle Number 1 2 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 ADC Clock ADEN ADSC ADIF ADCH MSB of Result ADCL LSB of Result MUX and REFS Conversion MUX and REFS Update Sample & Hold Complete Update ATmega8535(L) 210 2502K–AVR–10/06
ATmega8535(L) Figure 102. ADC Timing Diagram, Single Conversion One Conversion Next Conversion Cycle Number 1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 ADC Clock ADSC ADIF ADCH MSB of Result ADCL LSB of Result Sample & Hold Conversion MUX and REFS MUX and REFS Complete Update Update Figure 103. ADC Timing Diagram, Auto Triggered Conversion One Conversion Next Conversion Cycle Number 1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 ADC Clock Trigger Source ADATE ADIF ADCH MSB of Result ADCL LSB of Result Sample & Conversion Prescaler Prescaler Hold Complete Reset Reset MUX and REFS Update Figure 104. ADC Timing Diagram, Free Running Conversion One Conversion Next Conversion 11 12 13 1 2 3 4 Cycle Number ADC Clock ADSC ADIF ADCH MSB of Result ADCL LSB of Result Conversion Sample & Hold Complete MUX and REFS Update 211 2502K–AVR–10/06
Table 82. ADC Conversion Time Sample & Hold (Cycles Conversion Time Condition from Start of Conversion) (Cycles) First conversion 14.5 25 Normal conversions, single ended 1.5 13 Auto Triggered conversions 2 13.5 Normal conversions, differential 1.5/2.5(1) 13/14(1) Note: 1. Depending on the state of CK . ADC2 Differential Gain Channels When using differential gain channels, certain aspects of the conversion need to be taken into consideration. Differential conversions are synchronized to the internal clock CK equal to half the ADC2 ADC clock. This synchronization is done automatically by the ADC interface in such a way that the sample-and-hold occurs at a specific phase of CK . A conversion initi- ADC2 ated by the user (i.e., all single conversions, and the first free running conversion) when CK is low will take the same amount of time as a single ended conversion (13 ADC ADC2 clock cycles from the next prescaled clock cycle). A conversion initiated by the user when CK is high will take 14 ADC clock cycles due to the synchronization mecha- ADC2 nism. In free running mode, a new conversion is initiated immediately after the previous conversion completes, and since CK is high at this time, all automatically started ADC2 (i.e., all but the first) free running conversions will take 14 ADC clock cycles. The gain stage is optimized for a bandwidth of 4 kHz at all gain settings. Higher frequen- cies may be subjected to non-linear amplification. An external low-pass filter should be used if the input signal contains higher frequency components than the gain stage band- width. Note that the ADC clock frequency is independent of the gain stage bandwidth limitation. For example, the ADC clock period may be 6 µs, allowing a channel to be sampled at 12 kSPS, regardless of the bandwidth of this channel. If differential gain channels are used and conversions are started by Auto Triggering, the ADC must be switched off between conversions. When Auto Triggering is used, the ADC prescaler is reset before the conversion is started. Since the gain stage is depen- dent of a stable ADC clock prior to the conversion, this conversion will not be valid. By disabling and then re-enabling the ADC between each conversion (writing ADEN in ADCSRA to “0” then to “1”), only extended conversions are performed. The result from the extended conversions will be valid. See “Prescaling and Conversion Timing” on page 209 for timing details. Changing Channel or The MUXn and REFS1:0 bits in the ADMUX Register are single buffered through a tem- Reference Selection porary register to which the CPU has random access. This ensures that the channels and reference selection only takes place at a safe point during the conversion. The channel and reference selection is continuously updated until a conversion is started. Once the conversion starts, the channel and reference selection is locked to ensure a sufficient sampling time for the ADC. Continuous updating resumes in the last ADC clock cycle before the conversion completes (ADIF in ADCSRA is set). Note that the conversion starts on the following rising ADC clock edge after ADSC is written. The user is thus advised not to write new channel or reference selection values to ADMUX until one ADC clock cycle after ADSC is written. If Auto Triggering is used, the exact time of the triggering event can be indeterminable. Special care must be taken when updating the ADMUX Register, in order to control which conversion will be affected by the new settings. ATmega8535(L) 212 2502K–AVR–10/06
ATmega8535(L) If both ADATE and ADEN is written to one, an interrupt event can occur at any time. If the ADMUX Register is changed in this period, the user cannot tell if the next conversion is based on the old or the new settings. ADMUX can be safely updated in the following ways: 1. When ADATE or ADEN is cleared. 2. During conversion, minimum one ADC clock cycle after the trigger event. 3. After a conversion, before the interrupt flag used as trigger source is cleared. When updating ADMUX in one of these conditions, the new settings will affect the next ADC conversion. Special care should be taken when changing differential channels. Once a differential channel has been selected, the gain stage may take as much as 125 µs to stabilize to the new value. Thus conversions should not be started within the first 125 µs after selecting a new differential channel. Alternatively, conversion results obtained within this period should be discarded. The same settling time should be observed for the first differential conversion after changing ADC reference (by changing the REFS1:0 bits in ADMUX). ADC Input Channels When changing channel selections, the user should observe the following guidelines to ensure that the correct channel is selected: In Single Conversion mode, always select the channel before starting the conversion. The channel selection may be changed one ADC clock cycle after writing one to ADSC. However, the simplest method is to wait for the conversion to complete before changing the channel selection. In Free Running mode, always select the channel before starting the first conversion. The channel selection may be changed one ADC clock cycle after writing one to ADSC. However, the simplest method is to wait for the first conversion to complete, and then change the channel selection. Since the next conversion has already started automati- cally, the next result will reflect the previous channel selection. Subsequent conversions will reflect the new channel selection. When switching to a differential gain channel, the first conversion result may have a poor accuracy due to the required settling time for the automatic offset cancellation cir- cuitry. The user should preferably disregard the first conversion result. ADC Voltage Reference The reference voltage for the ADC (V ) indicates the conversion range for the ADC. REF Single ended channels that exceed V will result in codes close to 0x3FF. V can be REF REF selected as either AVCC, internal 2.56V reference, or external AREF pin. AVCC is connected to the ADC through a passive switch. The internal 2.56V reference is generated from the internal bandgap reference (V ) through an internal amplifier. In BG either case, the external AREF pin is directly connected to the ADC, and the reference voltage can be made more immune to noise by connecting a capacitor between the AREF pin and ground. V can also be measured at the AREF pin with a high impedant REF voltmeter. Note that V is a high impedant source, and only a capacitive load should REF be connected in a system. If the user has a fixed voltage source connected to the AREF pin, the user may not use the other reference voltage options in the application, as they will be shorted to the external voltage. If no external voltage is applied to the AREF pin, the user may switch between AVCC and 2.56V as reference selection. The first ADC conversion result after switching reference voltage source may be inaccurate, and the user is advised to dis- card this result. 213 2502K–AVR–10/06
If differential channels are used, the selected reference should not be closer to AVCC than indicated in Table 114 on page 263 and Table 115 on page 264. ADC Noise Canceler The ADC features a noise canceler that enables conversion during sleep mode to reduce noise induced from the CPU core and other I/O peripherals. The noise canceler can be used with ADC Noise Reduction and Idle mode. To make use of this feature, the following procedure should be used: 1. Make sure that the ADC is enabled and is not busy converting. Single Con- version mode must be selected and the ADC conversion complete interrupt must be enabled. 2. Enter ADC Noise Reduction mode (or Idle mode). The ADC will start a con- version once the CPU has been halted. 3. If no other interrupts occur before the ADC conversion completes, the ADC interrupt will wake up the CPU and execute the ADC Conversion Complete interrupt routine. If another interrupt wakes up the CPU before the ADC con- version is complete, that interrupt will be executed, and an ADC Conversion Complete interrupt request will be generated when the ADC conversion completes. The CPU will remain in active mode until a new sleep command is executed. Note that the ADC will not be automatically turned off when entering other sleep modes than Idle mode and ADC Noise Reduction mode. The user is advised to write zero to ADEN before entering such sleep modes to avoid excessive power consumption. If the ADC is enabled in such sleep modes and the user wants to perform differential conver- sions, the user is advised to switch the ADC off and on after waking up from sleep to prompt an extended conversion to get a valid result. Analog Input Circuitry The Analog Input Circuitry for single ended channels is illustrated in Figure 105. An ana- log source applied to ADCn is subjected to the pin capacitance and input leakage of that pin, regardless of whether that channel is selected as input for the ADC. When the chan- nel is selected, the source must drive the S/H capacitor through the series resistance (combined resistance in the input path). The ADC is optimized for analog signals with an output impedance of approximately 10kΩ or less. If such a source is used, the sampling time will be negligible. If a source with higher impedance is used, the sampling time will depend on how long time the source needs to charge the S/H capacitor, with can vary widely. The user is recom- mended to only use low impedant sources with slowly varying signals, since this minimizes the required charge transfer to the S/H capacitor. If differential gain channels are used, the input circuitry looks somewhat different, although source impedances of a few hundred kΩ or less is recommended. Signal components higher than the Nyquist frequency (f /2) should not be present for ADC either kind of channels, to avoid distortion from unpredictable signal convolution. The user is advised to remove high frequency components with a low-pass filter before applying the signals as inputs to the ADC. ATmega8535(L) 214 2502K–AVR–10/06
ATmega8535(L) Figure 105. Analog Input Circuitry I IH ADCn 1..100 kΩ C = 14 pF S/H I IL V /2 CC Analog Noise Canceling Digital circuitry inside and outside the device generates EMI which might affect the Techniques accuracy of analog measurements. If conversion accuracy is critical, the noise level can be reduced by applying the following techniques: 1. Keep analog signal paths as short as possible. Make sure analog tracks run over the analog ground plane, and keep them well away from high-speed switching digital tracks. 2. The AVCC pin on the device should be connected to the digital V supply CC voltage via an LC network as shown in Figure 106. 3. Use the ADC noise canceler function to reduce induced noise from the CPU. 4. If any ADC port pins are used as digital outputs, it is essential that these do not switch while a conversion is in progress. Figure 106. ADC Power Connections 0) 1) 2) 3) ne C C C C a D D D D Pl A A A A d GND VCC PA0 ( PA1 ( PA2 ( PA3 ( Groun g o al n A PA4 (ADC4) PA5 (ADC5) PA6 (ADC6) PA7 (ADC7) Η AREF μ 0 1 GND F n 0 0 AVCC 1 PC7 215 2502K–AVR–10/06
Offset Compensation The gain stage has a built-in offset cancellation circuitry that nulls the offset of differen- Schemes tial measurements as much as possible. The remaining offset in the analog path can be measured directly by selecting the same channel for both differential inputs. This offset residue can be then subtracted in software from the measurement results. Using this kind of software based offset correction, offset on any channel can be reduced below one LSB. ADC Accuracy Definitions An n-bit single-ended ADC converts a voltage linearly between GND and V in 2n REF steps (LSBs). The lowest code is read as 0, and the highest code is read as 2n - 1. Several parameters describe the deviation from the ideal behavior: (cid:129) Offset: The deviation of the first transition (0x000 to 0x001) compared to the ideal transition (at 0.5 LSB). Ideal value: 0 LSB. Figure 107. Offset Error Output Code Ideal ADC Actual ADC Offset Error VREF Input Voltage (cid:129) Gain Error: After adjusting for offset, the Gain Error is found as the deviation of the last transition (0x3FE to 0x3FF) compared to the ideal transition (at 1.5 LSB below maximum). Ideal value: 0 LSB. Figure 108. Gain Error Output Code Gain Error Ideal ADC Actual ADC VREF Input Voltage ATmega8535(L) 216 2502K–AVR–10/06
ATmega8535(L) (cid:129) Integral Non-linearity (INL): After adjusting for offset and gain error, the INL is the maximum deviation of an actual transition compared to an ideal transition for any code. Ideal value: 0 LSB. Figure 109. Integral Non-linearity (INL) Output Code IN L Ideal ADC Actual ADC V Input Voltage REF (cid:129) Differential Non-linearity (DNL): The maximum deviation of the actual code width (the interval between two adjacent transitions) from the ideal code width (1 LSB). Ideal value: 0 LSB. Figure 110. Differential Non-linearity (DNL) Output Code 0x3FF 1 LSB DNL 0x000 0 V Input Voltage REF (cid:129) Quantization Error: Due to the quantization of the input voltage into a finite number of codes, a range of input voltages (1 LSB wide) will code to the same value. Always ±0.5 LSB. (cid:129) Absolute Accuracy: The maximum deviation of an actual (unadjusted) transition compared to an ideal transition for any code. This is the compound effect of Offset, Gain Error, Differential Error, Non-linearity, and Quantization Error. Ideal value: ±0.5LSB. 217 2502K–AVR–10/06
ADC Conversion Result After the conversion is complete (ADIF is high), the conversion result can be found in the ADC Result Registers (ADCL, ADCH). For single ended conversion, the result is V ⋅1024 IN ADC = -------------------------- V REF where V is the voltage on the selected input pin and V the selected voltage refer- IN REF ence (see Table 84 on page 219 and Table 85 on page 220). 0x000 represents analog ground, and 0x3FF represents the selected reference voltage minus one LSB. If differential channels are used, the result is (V –V )⋅GAIN⋅512 ADC = -------P---O----S------------N----E---G--------------------------------------- V REF where V is the voltage on the positive input pin, V the voltage on the negative POS NEG input pin, GAIN the selected gain factor, and V the selected voltage reference. The REF result is presented in two’s complement form, from 0x200 (-512d) through 0x1FF (+511d). Note that if the user wants to perform a quick polarity check of the results, it is sufficient to read the MSB of the result (ADC9 in ADCH). If the bit is one, the result is negative, and if the bit is zero, the result is positive. Figure 111 shows the decoding of the differential input range. Table 83 shows the resulting output codes if the differential input channel pair (ADCn - ADCm) is selected with a gain of GAIN and a reference voltage of V . REF Figure 111. Differential Measurement Range Output Code 0x1FF 0x000 - VREF/GAIN 0x3FF 0 VREF/GAIN DVoiflfteargeen t(iVaol Iltnsp)ut 0x200 ATmega8535(L) 218 2502K–AVR–10/06
ATmega8535(L) Table 83. Correlation Between Input Voltage and Output Codes V Read Code Corresponding Decimal Value ADCn V + V /GAIN 0x1FF 511 ADCm REF V + (511/512) V /GAIN 0x1FF 511 ADCm REF V + (510/512) V /GAIN 0x1FE 510 ADCm REF ... ... ... V + (1/512) V /GAIN 0x001 1 ADCm REF V 0x000 0 ADCm V - (1/512) V /GAIN 0x3FF -1 ADCm REF ... ... ... V - (511/512) V /GAIN 0x201 -511 ADCm REF V - V /GAIN 0x200 -512 ADCm REF Example: ADMUX = 0xED (ADC3 - ADC2, 10x gain, 2.56V reference, left adjusted result) Voltage on ADC3 is 300 mV, voltage on ADC2 is 500 mV. ADCR = 512 * 10 * (300 - 500)/2560 = -400 = 0x270 ADCL will thus read 0x00, and ADCH will read 0x9C. Writing zero to ADLAR right adjusts the result: ADCL = 0x70, ADCH = 0x02. ADC Multiplexer Selection Register – ADMUX Bit 7 6 5 4 3 2 1 0 REFS1 REFS0 ADLAR MUX4 MUX3 MUX2 MUX1 MUX0 ADMUX Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 7:6 – REFS1:0: Reference Selection Bits These bits select the voltage reference for the ADC, as shown in Table 84. If these bits are changed during a conversion, the change will not go in effect until this conversion is complete (ADIF in ADCSRA is set). The internal voltage reference options may not be used if an external reference voltage is being applied to the AREF pin. Table 84. Voltage Reference Selections for ADC REFS1 REFS0 Voltage Reference Selection 0 0 AREF, Internal Vref turned off 0 1 AVCC with external capacitor at AREF pin 1 0 Reserved 1 1 Internal 2.56V Voltage Reference with external capacitor at AREF pin (cid:129) Bit 5 – ADLAR: ADC Left Adjust Result The ADLAR bit affects the presentation of the ADC conversion result in the ADC Data Register. Write one to ADLAR to left adjust the result. Otherwise, the result is right adjusted. Changing the ADLAR bit will affect the ADC Data Register immediately, regardless of any ongoing conversions. For a complete description of this bit, see “The ADC Data Register – ADCL and ADCH” on page 222. 219 2502K–AVR–10/06
(cid:129) Bits 4:0 – MUX4:0: Analog Channel and Gain Selection Bits The value of these bits selects which combination of analog inputs are connected to the ADC. These bits also select the gain for the differential channels. See Table 85 for details. If these bits are changed during a conversion, the change will not go in effect until this conversion is complete (ADIF in ADCSRA is set). Table 85. Input Channel and Gain Selections MUX4..0 Single Ended Input Pos Differential Input Neg Differential Input Gain 00000 ADC0 00001 ADC1 00010 ADC2 00011 ADC3 N/A 00100 ADC4 00101 ADC5 00110 ADC6 00111 ADC7 01000 ADC0 ADC0 10x 01001 ADC1 ADC0 10x 01010 ADC0 ADC0 200x 01011 ADC1 ADC0 200x 01100 ADC2 ADC2 10x 01101 ADC3 ADC2 10x 01110 ADC2 ADC2 200x 01111 ADC3 ADC2 200x 10000 ADC0 ADC1 1x 10001 ADC1 ADC1 1x 10010 N/A ADC2 ADC1 1x 10011 ADC3 ADC1 1x 10100 ADC4 ADC1 1x 10101 ADC5 ADC1 1x 10110 ADC6 ADC1 1x 10111 ADC7 ADC1 1x 11000 ADC0 ADC2 1x 11001 ADC1 ADC2 1x 11010 ADC2 ADC2 1x 11011 ADC3 ADC2 1x 11100 ADC4 ADC2 1x ATmega8535(L) 220 2502K–AVR–10/06
ATmega8535(L) Table 85. Input Channel and Gain Selections (Continued) MUX4..0 Single Ended Input Pos Differential Input Neg Differential Input Gain 11101 ADC5 ADC2 1x 11110 1.22V (V ) N/A BG 11111 0V (GND) ADC Control and Status Register A – ADCSRA Bit 7 6 5 4 3 2 1 0 ADEN ADSC ADATE ADIF ADIE ADPS2 ADPS1 ADPS0 ADCSRA Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 7 – ADEN: ADC Enable Writing this bit to one enables the ADC. By writing it to zero, the ADC is turned off. Turn- ing the ADC off while a conversion is in progress, will terminate this conversion. (cid:129) Bit 6 – ADSC: ADC Start Conversion In Single Conversion mode, write this bit to one to start each conversion. In Free Run- ning mode, write this bit to one to start the first conversion. The first conversion after ADSC has been written after the ADC has been enabled, or if ADSC is written at the same time as the ADC is enabled, will take 25 ADC clock cycles instead of the normal 13. This first conversion performs initialization of the ADC. ADSC will read as one as long as a conversion is in progress. When the conversion is complete, it returns to zero. Writing zero to this bit has no effect. (cid:129) Bit 5 – ADATE: ADC Auto Trigger Enable When this bit is written to one, Auto Triggering of the ADC is enabled. The ADC will start a conversion on a positive edge of the selected trigger signal. The trigger source is selected by setting the ADC Trigger Select bits, ADTS in SFIOR. (cid:129) Bit 4 – ADIF: ADC Interrupt Flag This bit is set when an ADC conversion completes and the Data Registers are updated. The ADC Conversion Complete Interrupt is executed if the ADIE bit and the I-bit in SREG are set. ADIF is cleared by hardware when executing the corresponding interrupt handling vector. Alternatively, ADIF is cleared by writing a logical one to the flag. Beware that if doing a Read-Modify-Write on ADCSRA, a pending interrupt can be dis- abled. This also applies if the SBI and CBI instructions are used. (cid:129) Bit 3 – ADIE: ADC Interrupt Enable When this bit is written to one and the I-bit in SREG is set, the ADC Conversion Com- plete Interrupt is activated. (cid:129) Bits 2:0 – ADPS2:0: ADC Prescaler Select Bits These bits determine the division factor between the XTAL frequency and the input clock to the ADC. 221 2502K–AVR–10/06
Table 86. ADC Prescaler Selections ADPS2 ADPS1 ADPS0 Division Factor 0 0 0 2 0 0 1 2 0 1 0 4 0 1 1 8 1 0 0 16 1 0 1 32 1 1 0 64 1 1 1 128 The ADC Data Register – ADCL and ADCH ADLAR = 0 Bit 15 14 13 12 11 10 9 8 – – – – – – ADC9 ADC8 ADCH ADC7 ADC6 ADC5 ADC4 ADC3 ADC2 ADC1 ADC0 ADCL 7 6 5 4 3 2 1 0 Read/Write R R R R R R R R R R R R R R R R Initial Value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ADLAR = 1 Bit 15 14 13 12 11 10 9 8 ADC9 ADC8 ADC7 ADC6 ADC5 ADC4 ADC3 ADC2 ADCH ADC1 ADC0 – – – – – – ADCL 7 6 5 4 3 2 1 0 Read/Write R R R R R R R R R R R R R R R R Initial Value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 When an ADC conversion is complete, the result is found in these two registers. If differ- ential channels are used, the result is presented in two’s complement form. When ADCL is read, the ADC Data Register is not updated until ADCH is read. Conse- quently, if the result is left adjusted and no more than 8-bit precision is required, it is sufficient to read ADCH. Otherwise, ADCL must be read first, then ADCH. The ADLAR bit in ADMUX, and the MUXn bits in ADMUX affect the way the result is read from the registers. If ADLAR is set, the result is left adjusted. If ADLAR is cleared (default), the result is right adjusted. (cid:129) ADC9:0: ADC Conversion Result These bits represent the result from the conversion, as detailed in “ADC Conversion Result” on page 218. ATmega8535(L) 222 2502K–AVR–10/06
ATmega8535(L) Special Function IO Register – SFIOR Bit 7 6 5 4 3 2 1 0 ADTS2 ADTS1 ADTS0 – ACME PUD PSR2 PSR10 SFIOR Read/Write R/W R/W R/W R R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 7:5 – ADTS2:0: ADC Auto Trigger Source If ADATE in ADCSRA is written to one, the value of these bits selects which source will trigger an ADC conversion. If ADATE is cleared, the ADTS2:0 settings will have no effect. A conversion will be triggered by the rising edge of the selected interrupt flag. Note that switching from a trigger source that is cleared to a trigger source that is set, will generate a positive edge on the trigger signal. If ADEN in ADCSRA is set, this will start a conversion. Switching to Free Running mode (ADTS[2:0]=0) will not cause a trig- ger event, even if the ADC Interrupt Flag is set. Table 87. ADC Auto Trigger Source Selections ADTS2 ADTS1 ADTS0 Trigger Source 0 0 0 Free Running mode 0 0 1 Analog Comparator 0 1 0 External Interrupt Request 0 0 1 1 Timer/Counter0 Compare Match 1 0 0 Timer/Counter0 Overflow 1 0 1 Timer/Counter1 Compare Match B 1 1 0 Timer/Counter1 Overflow 1 1 1 Timer/Counter1 Capture Event (cid:129) Bit 4 – RES: Reserved Bit This bit is reserved bit in the ATmega8535, and will always read as zero. 223 2502K–AVR–10/06
Boot Loader Support The Boot Loader Support provides a real Read-While-Write Self-Programming mecha- – Read-While-Write nism for downloading and uploading program code by the MCU itself. This feature allows flexible application software updates controlled by the MCU using a Flash-resi- Self-Programming dent Boot Loader program. The Boot Loader program can use any available data interface and associated protocol to read code and write (program) that code into the Flash memory, or read the code from the Program memory. The program code within the Boot Loader section has the capability to write into the entire Flash, including the Boot Loader memory. The Boot Loader can thus even modify itself, and it can also erase itself from the code if the feature is not needed anymore. The size of the Boot Loader memory is configurable with fuses and the Boot Loader has two separate sets of Boot Lock bits which can be set independently. This gives the user a unique flexibility to select different levels of protection. Boot Loader Features (cid:129) Read-While-Write Self-Programming (cid:129) Flexible Boot Memory Size (cid:129) High Security (Separate Boot Lock Bits for a Flexible Protection) (cid:129) Separate Fuse to Select Reset Vector (cid:129) Optimized Page(1) Size (cid:129) Code Efficient Algorithm (cid:129) Efficient Read-Modify-Write Support Note: 1. A page is a section in the Flash consisting of several bytes (see Table 104 on page 241) used during programming. The page organization does not affect normal operation. Application and Boot The Flash memory is organized in two main sections, the Application section and the Loader Flash Sections Boot Loader section (see Figure 113). The size of the different sections is configured by the BOOTSZ Fuses as shown in Table 93 on page 235 and Figure 113. These two sec- tions can have different level of protection since they have different sets of Lock bits. Application Section The Application section is the section of the Flash that is used for storing the application code. The protection level for the Application section can be selected by the Application Boot Lock bits (Boot Lock bits 0), see Table 89 on page 227. The Application section can never store any Boot Loader code since the SPM instruction is disabled when exe- cuted from the Application section. BLS – Boot Loader Section While the Application section is used for storing the application code, the The Boot Loader software must be located in the BLS since the SPM instruction can initiate a pro- gramming when executing from the BLS only. The SPM instruction can access the entire Flash, including the BLS itself. The protection level for the Boot Loader section can be selected by the Boot Loader Lock bits (Boot Lock bits 1), see Table 90 on page 227. Read-While-Write and No Whether the CPU supports Read-While-Write or if the CPU is halted during a Boot Read-While-Write Flash Loader software update is dependent on which address that is being programmed. In Sections addition to the two sections that are configurable by the BOOTSZ Fuses as described above, the Flash is also divided into two fixed sections, the Read-While-Write (RWW) section and the No Read-While-Write (NRWW) section. The limit between the RWW- and NRWW sections is given in Table 94 on page 235 and Figure 113 on page 226. The main difference between the two sections is: (cid:129) When erasing or writing a page located inside the RWW section, the NRWW section can be read during the operation. (cid:129) When erasing or writing a page located inside the NRWW section, the CPU is halted during the entire operation. ATmega8535(L) 224 2502K–AVR–10/06
ATmega8535(L) Note that the user software can never read any code that is located inside the RWW section during a Boot Loader software operation. The syntax “Read-While-Write Sec- tion” refers to which section that is being programmed (erased or written), not which section that actually is being read during a Boot Loader software update. RWW – Read-While-Write If a Boot Loader software update is programming a page inside the RWW section, it is Section possible to read code from the Flash, but only code that is located in the NRWW sec- tion. During an on-going programming, the software must ensure that the RWW section never is being read. If the user software is trying to read code that is located inside the RWW section (i.e., by a rcall/rjmp/lpm or an interrupt) during programming, the software might end up in an unknown state. To avoid this, the interrupts should either be disabled or moved to the Boot Loader section. The Boot Loader section is always located in the NRWW section. The RWW Section Busy bit (RWWSB) in the Store Program Memory Control Register (SPMCR) will be read as logical one as long as the RWW section is blocked for reading. After a programming is completed, the RWWSB must be cleared by software before reading code located in the RWW section. See “Store Program Memory Control Register – SPMCR” on page 228. for details on how to clear RWWSB. NRWW – No Read-While-Write The code located in the NRWW section can be read when the Boot Loader software is Section updating a page in the RWW section. When the Boot Loader code updates the NRWW section, the CPU is halted during the entire page erase or page write operation. Table 88. Read-While-Write Features Which Section does the Z- Which Section can be Is the Read-While- pointer Address During the Read During CPU Write Programming? Programming? Halted? Supported? RWW section NRWW section No Yes NRWW section None Yes No Figure 112. Read-While-Write vs. No Read-While-Write Read-While-Write (RWW) Section Z-pointer Addresses NRWW Section Z-pointer Addresses RWW No Read-While-Write Section (NRWW) Section CPU is Halted During the Operation Code Located in NRWW Section can be Read During the Operation 225 2502K–AVR–10/06
Figure 113. Memory sections(1) Program Memory Program Memory BOOTSZ = '11' BOOTSZ = '10' $0000 $0000 Section Section Write Application Flash Section Write Application Flash Section While- While- Read- Read- Section ESntadr tR NWRWWW Section ESntadr tR NWRWWW Write Application Flash Section Write Application Flash Section While- End Application While- ESntadr tA Bpopolitc Laotioander Read- Boot Loader Flash Section FSltaasrth Benodot Loader Read- Boot Loader Flash Section Flashend No No Program Memory Program Memory BOOTSZ = '01' BOOTSZ = '00' $0000 $0000 Section Section Write Application Flash Section Write Application Flash Section While- While- Read- Read- Write Section Application Flash Section ESEntnaddr tRA NpWRpWWlicWation Write Section ESntadr tR NWRWW,W E,n Sdt aArpt pBliocoatt iLoonader While- Boot Loader Flash Section Start Boot Loader While- Boot Loader Flash Section Read- Flashend Read- Flashend No No Note: 1. The parameters in the figure above are given in Table 93 on page 235. Boot Loader Lock Bits If no Boot Loader capability is needed, the entire Flash is available for application code. The Boot Loader has two separate sets of Boot Lock bits which can be set indepen- dently. This gives the user a unique flexibility to select different levels of protection. The user can select: (cid:129) To protect the entire Flash from a software update by the MCU. (cid:129) To protect only the Boot Loader Flash section from a software update by the MCU. (cid:129) To protect only the Application Flash section from a software update by the MCU. (cid:129) Allow software update in the entire Flash. See Table 89 and Table 90 for further details. The Boot Lock bits can be set in software and in Serial or Parallel Programming mode, but they can be cleared by a Chip Erase command only. The general Write Lock (Lock Bit mode 2) does not control the program- ming of the Flash memory by SPM instruction. Similarly, the general Read/Write Lock (Lock Bit mode 1) does not control reading nor writing by LPM/SPM, if it is attempted. ATmega8535(L) 226 2502K–AVR–10/06
ATmega8535(L) Table 89. Boot Lock Bit0 Protection Modes (Application Section)(1) BLB0 Mode BLB02 BLB01 Protection No restrictions for SPM or LPM accessing the Application 1 1 1 section. 2 1 0 SPM is not allowed to write to the Application section. SPM is not allowed to write to the Application section, and LPM executing from the Boot Loader section is not 3 0 0 allowed to read from the Application section. If interrupt vectors are placed in the Boot Loader section, interrupts are disabled while executing from the Application section. LPM executing from the Boot Loader section is not allowed to read from the Application section. If interrupt 4 0 1 vectors are placed in the Boot Loader section, interrupts are disabled while executing from the Application section. Note: 1. “1” means unprogrammed, “0” means programmed. Table 90. Boot Lock Bit1 Protection Modes (Boot Loader Section)(1) BLB1 Mode BLB12 BLB11 Protection No restrictions for SPM or LPM accessing the Boot Loader 1 1 1 section. 2 1 0 SPM is not allowed to write to the Boot Loader section. SPM is not allowed to write to the Boot Loader section, and LPM executing from the Application section is not 3 0 0 allowed to read from the Boot Loader section. If interrupt vectors are placed in the Application section, interrupts are disabled while executing from the Boot Loader section. LPM executing from the Application section is not allowed to read from the Boot Loader section. If interrupt vectors 4 0 1 are placed in the Application section, interrupts are disabled while executing from the Boot Loader section. Note: 1. “1” means unprogrammed, “0” means programmed. Entering the Boot Loader Entering the Boot Loader takes place by a jump or call from the application program. Program This may be initiated by a trigger such as a command received via USART, or SPI inter- face. Alternatively, the Boot Reset Fuse can be programmed so that the Reset Vector is pointing to the Boot Flash start address after a reset. In this case, the Boot Loader is started after a reset. After the application code is loaded, the program can start execut- ing the application code. Note that the fuses cannot be changed by the MCU itself. This means that once the Boot Reset Fuse is programmed, the Reset Vector will always point to the Boot Loader Reset and the fuse can only be changed through the serial or parallel programming interface. Table 91. Boot Reset Fuse(1) BOOTRST Reset Address 1 Reset Vector = Application Reset (address 0x0000) 0 Reset Vector = Boot Loader Reset (see Table 93 on page 235) Note: 1. “1” means unprogrammed, “0” means programmed. 227 2502K–AVR–10/06
Store Program Memory The Store Program Memory Control Register contains the control bits needed to control Control Register – SPMCR the Boot Loader operations. Bit 7 6 5 4 3 2 1 0 SPMIE RWWSB – RWWSRE BLBSET PGWRT PGERS SPMEN SPMCR Read/Write R/W R R R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 (cid:129) Bit 7 – SPMIE: SPM Interrupt Enable When the SPMIE bit is written to one, and the I-bit in the Status Register is set (one), the SPM ready interrupt will be enabled. The SPM ready Interrupt will be executed as long as the SPMEN bit in the SPMCR Register is cleared. (cid:129) Bit 6 – RWWSB: Read-While-Write Section Busy When a Self-Programming (Page Erase or Page Write) operation to the RWW section is initiated, the RWWSB will be set (one) by hardware. When the RWWSB bit is set, the RWW section cannot be accessed. The RWWSB bit will be cleared if the RWWSRE bit is written to one after a Self-Programming operation is completed. Alternatively the RWWSB bit will automatically be cleared if a page load operation is initiated. (cid:129) Bit 5 – Res: Reserved Bit This bit is a reserved bit in the ATmega8535 and always read as zero. (cid:129) Bit 4 – RWWSRE: Read-While-Write Section Read Enable When programming (page erase or page write) to the RWW section, the RWW section is blocked for reading (the RWWSB will be set by hardware). To re-enable the RWW section, the user software must wait until the programming is completed (SPMEN will be cleared). Then, if the RWWSRE bit is written to one at the same time as SPMEN, the next SPM instruction within four clock cycles re-enables the RWW section. The RWW section cannot be re-enabled while the Flash is busy with a page erase or a page write (SPMEN is set). If the RWWSRE bit is written while the Flash is being loaded, the Flash load operation will abort and the data loaded will be lost. (cid:129) Bit 3 – BLBSET: Boot Lock Bit Set If this bit is written to one at the same time as SPMEN, the next SPM instruction within four clock cycles sets Boot Lock bits, according to the data in R0. The data in R1 and the address in the Z-pointer are ignored. The BLBSET bit will automatically be cleared upon completion of the Lock bit set, or if no SPM instruction is executed within four clock cycles. An LPM instruction within three cycles after BLBSET and SPMEN are set in the SPMCR Register, will read either the Lock bits or the Fuse bits (depending on Z0 in the Z- pointer) into the destination register. See “Reading the Fuse and Lock Bits from Soft- ware” on page 232 for details. (cid:129) Bit 2 – PGWRT: Page Write If this bit is written to one at the same time as SPMEN, the next SPM instruction within four clock cycles executes page write, with the data stored in the temporary buffer. The page address is taken from the high part of the Z-pointer. The data in R1 and R0 are ignored. The PGWRT bit will auto-clear upon completion of a page write, or if no SPM instruction is executed within four clock cycles. The CPU is halted during the entire page write operation if the NRWW section is addressed. (cid:129) Bit 1 – PGERS: Page Erase If this bit is written to one at the same time as SPMEN, the next SPM instruction within four clock cycles executes page erase. The page address is taken from the high part of ATmega8535(L) 228 2502K–AVR–10/06
ATmega8535(L) the Z-pointer. The data in R1 and R0 are ignored. The PGERS bit will auto-clear upon completion of a page erase, or if no SPM instruction is executed within four clock cycles. The CPU is halted during the entire page write operation if the NRWW section is addressed. (cid:129) Bit 0 – SPMEN: Store Program Memory Enable This bit enables the SPM instruction for the next four clock cycles. If written to one together with either RWWSRE, BLBSET, PGWRT’ or PGERS, the following SPM instruction will have a special meaning, see description above. If only SPMEN is written, the following SPM instruction will store the value in R1:R0 in the temporary page buffer addressed by the Z-pointer. The LSB of the Z-pointer is ignored. The SPMEN bit will auto-clear upon completion of an SPM instruction, or if no SPM instruction is executed within four clock cycles. During page erase and page write, the SPMEN bit remains high until the operation is completed. Writing any other combination than “10001”, “01001”, “00101”, “00011” or “00001” in the lower five bits will have no effect. Addressing the Flash The Z-pointer is used to address the SPM commands. during Self- Bit 15 14 13 12 11 10 9 8 Programming ZH (R31) Z15 Z14 Z13 Z12 Z11 Z10 Z9 Z8 ZL (R30) Z7 Z6 Z5 Z4 Z3 Z2 Z1 Z0 7 6 5 4 3 2 1 0 Since the Flash is organized in pages (see Table 104 on page 241), the Program Counter can be treated as having two different sections. One section, consisting of the least significant bits, is addressing the words within a page, while the most significant bits are addressing the pages. This is shown in Figure 114. Note that the Page Erase and Page Write operations are addressed independently. Therefore it is of major impor- tance that the Boot Loader software addresses the same page in both the Page Erase and Page Write operation. Once a programming operation is initiated, the address is latched and the Z-pointer can be used for other operations. The only SPM operation that does not use the Z-pointer is Setting the Boot Loader Lock bits. The content of the Z-pointer is ignored and will have no effect on the operation. The LPM instruction does also use the Z-pointer to store the address. Since this instruction addresses the Flash byte by byte, also the LSB (bit Z0) of the Z-pointer is used. 229 2502K–AVR–10/06
Figure 114. Addressing the Flash during SPM(1) BIT 15 ZPCMSB ZPAGEMSB 1 0 Z - REGISTER 0 PCMSB PAGEMSB PROGRAM PCPAGE PCWORD COUNTER PAGE ADDRESS WORD ADDRESS WITHIN THE FLASH WITHIN A PAGE PROGRAM MEMORY PAGE PCWORD[PAGEMSB:0]: PAGE INSTRUCTION WORD 00 01 02 PAGEEND Notes: 1. The different variables used+ in Figure 114 are listed in Table 95 on page 236. 2. PCPAGE and PCWORD are listed in Table 104 on page 241. Self-Programming the The program memory is updated in a page by page fashion. Before programming a Flash page with the data stored in the temporary page buffer, the page must be erased. The temporary page buffer is filled one word at a time using SPM and the buffer can be filled either before the Page Erase command or between a Page Erase and a Page Write operation: Alternative 1, fill the buffer before a Page Erase: (cid:129) Fill temporary page buffer (cid:129) Perform a Page Erase (cid:129) Perform a Page Write Alternative 2, fill the buffer after Page Erase: (cid:129) Perform a Page Erase (cid:129) Fill temporary page buffer (cid:129) Perform a Page Write If only a part of the page needs to be changed, the rest of the page must be stored (for example in the temporary page buffer) before the erase, and then be rewritten. When using alternative 1, the Boot Loader provides an effective Read-Modify-Write feature which allows the user software to first read the page, do the necessary changes, and then write back the modified data. If alternative 2 is used, it is not possible to read the old data while loading since the page is already erased. The temporary page buffer can be accessed in a random sequence. It is essential that the page address used in both the page erase and page write operation is addressing the same page. See “Simple Assembly Code Example for a Boot Loader” on page 233 for an assembly code example. ATmega8535(L) 230 2502K–AVR–10/06
ATmega8535(L) Performing Page Erase by To execute Page Erase, set up the address in the Z-pointer, write “X0000011” to SPM SPMCR and execute SPM within four clock cycles after writing SPMCR. The data in R1 and R0 is ignored. The page address must be written to PCPAGE in the Z-register. Other bits in the Z-pointer will be ignored during this operation. (cid:129) Page Erase to the RWW section: The NRWW section can be read during the Page Erase. (cid:129) Page Erase to the NRWW section: The CPU is halted during the operation. Filling the Temporary Buffer To write an instruction word, set up the address in the Z-pointer and data in R1:R0, write (Page Loading) “00000001” to SPMCR and execute SPM within four clock cycles after writing SPMCR. The content of PCWORD in the Z-register is used to address the data in the temporary buffer. The temporary buffer will auto-erase after a Page Write operation or by writing the RWWSRE bit in SPMCR. It is also erased after a System Reset. Note that it is not possible to write more than one time to each address without erasing the temporary buffer. Note: If the EEPROM is written in the middle of an SPM Page Load operation, all data loaded will be lost. Performing a Page Write To execute Page Write, set up the address in the Z-pointer, write “X0000101” to SPMCR and execute SPM within four clock cycles after writing SPMCR. The data in R1 and R0 is ignored. The page address must be written to PCPAGE. Other bits in the Z- pointer must be written to zero during this operation. (cid:129) Page Write to the RWW section: The NRWW section can be read during the Page Write. (cid:129) Page Write to the NRWW section: The CPU is halted during the operation. Using the SPM Interrupt If the SPM interrupt is enabled, the SPM interrupt will generate a constant interrupt when the SPMEN bit in SPMCR is cleared. This means that the interrupt can be used instead of polling the SPMCR Register in software. When using the SPM interrupt, the Interrupt Vectors should be moved to the BLS section to avoid that an interrupt is accessing the RWW section when it is blocked for reading. How to move the interrupts is described in “Interrupts” on page 46. Consideration While Updating Special care must be taken if the user allows the Boot Loader section to be updated by BLS leaving Boot Lock bit 11 unprogrammed. An accidental write to the Boot Loader itself can corrupt the entire Boot Loader, and further software updates might be impossible. If it is not necessary to change the Boot Loader software itself, it is recommended to pro- gram the Boot Lock bit 11 to protect the Boot Loader software from any internal software changes. Prevent Reading the RWW During Self-Programming (either Page Erase or Page Write), the RWW section is Section During always blocked for reading. The user software itself must prevent that this section is Self-Programming addressed during the Self-Programming operation. The RWWSB in the SPMCR will be set as long as the RWW section is busy. During Self-Programming the Interrupt Vector table should be moved to the BLS as described in “Interrupts” on page 46, or the inter- rupts must be disabled. Before addressing the RWW section after the programming is completed, the user software must clear the RWWSB by writing the RWWSRE. See “Simple Assembly Code Example for a Boot Loader” on page 233 for an example. 231 2502K–AVR–10/06
Setting the Boot Loader Lock To set the Boot Loader Lock bits, write the desired data to R0, write “X0001001” to Bits by SPM SPMCR and execute SPM within four clock cycles after writing SPMCR. The only accessible Lock bits are the Boot Lock bits that may prevent the Application and Boot Loader section from any software update by the MCU. Bit 7 6 5 4 3 2 1 0 R0 1 1 BLB12 BLB11 BLB02 BLB01 1 1 See Table 89 and Table 90 for how the different settings of the Boot Loader bits affect the Flash access. If bits 5..2 in R0 are cleared (zero), the corresponding Boot Lock bit will be programmed if an SPM instruction is executed within four cycles after BLBSET and SPMEN are set in SPMCR. The Z-pointer is don’t care during this operation, but for future compatibility it is recommended to load the Z-pointer with 0x0001 (same as used for reading the Lock bits). For future compatibility It is also recommended to set bits 7, 6, 1, and 0 in R0 to “1” when writing the Lock bits. When programming the Lock bits the entire Flash can be read during the operation. EEPROM Write Prevents Note that an EEPROM write operation will block all software programming to Flash. Writing to SPMCR Reading the Fuses and Lock bits from software will also be prevented during the EEPROM write operation. It is recommended that the user checks the status bit (EEWE) in the EECR Register and verifies that the bit is cleared before writing to the SPMCR Register. Reading the Fuse and Lock It is possible to read both the Fuse and Lock bits from software. To read the Lock bits, Bits from Software load the Z-pointer with 0x0001 and set the BLBSET and SPMEN bits in SPMCR. When an LPM instruction is executed within three CPU cycles after the BLBSET and SPMEN bits are set in SPMCR, the value of the Lock bits will be loaded in the destination regis- ter. The BLBSET and SPMEN bits will auto-clear upon completion of reading the Lock bits or if no LPM instruction is executed within three CPU cycles or no SPM instruction is executed within four CPU cycles. When BLBSET and SPMEN are cleared, LPM will work as described in the Instruction set Manual. Bit 7 6 5 4 3 2 1 0 Rd – – BLB12 BLB11 BLB02 BLB01 LB2 LB1 The algorithm for reading the Fuse Low bits is similar to the one described above for reading the Lock bits. To read the Fuse Low bits, load the Z-pointer with 0x0000 and set the BLBSET and SPMEN bits in SPMCR. When an LPM instruction is executed within three cycles after the BLBSET and SPMEN bits are set in the SPMCR, the value of the Fuse Low bits (FLB) will be loaded in the destination register as shown below. Refer to Table 99 on page 239 for a detailed description and mapping of the Fuse Low bits. Bit 7 6 5 4 3 2 1 0 Rd FLB7 FLB6 FLB5 FLB4 FLB3 FLB2 FLB1 FLB0 Similarly, when reading the Fuse High bits, load 0x0003 in the Z-pointer. When an LPM instruction is executed within three cycles after the BLBSET and SPMEN bits are set in the SPMCR, the value of the Fuse High bits (FHB) will be loaded in the destination reg- ister as shown below. Refer to Table 98 on page 238 for detailed description and mapping of the Fuse High bits. Bit 7 6 5 4 3 2 1 0 Rd FHB7 FHB6 FHB5 FHB4 FHB3 FHB2 FHB1 FHB0 ATmega8535(L) 232 2502K–AVR–10/06
ATmega8535(L) Fuse and Lock bits that are programmed, will be read as zero. Fuse and Lock bits that are unprogrammed, will be read as one. Preventing Flash Corruption During periods of low V the Flash program can be corrupted because the supply volt- CC, age is too low for the CPU and the Flash to operate properly. These issues are the same as for board level systems using the Flash, and the same design solutions should be applied. A Flash program corruption can be caused by two situations when the voltage is too low. First, a regular write sequence to the Flash requires a minimum voltage to operate cor- rectly. Secondly, the CPU itself can execute instructions incorrectly, if the supply voltage for executing instructions is too low. Flash corruption can easily be avoided by following these design recommendations (one is sufficient): 1. If there is no need for a Boot Loader update in the system, program the Boot Loader Lock bits to prevent any Boot Loader software updates. 2. Keep the AVR RESET active (low) during periods of insufficient power supply voltage. This can be done by enabling the internal Brown-out Detector (BOD) if the operating voltage matches the detection level. If not, an external low V CC Reset Protection circuit can be used. If a Reset occurs while a write operation is in progress, the write operation will be completed provided that the power supply voltage is sufficient. 3. Keep the AVR core in Power-down Sleep mode during periods of low V . This CC will prevent the CPU from attempting to decode and execute instructions, effec- tively protecting the SPMCR Register and thus the Flash from unintentional writes. Programming Time for Flash The calibrated RC Oscillator is used to time Flash accesses. Table 92 shows the typical When Using SPM programming time for Flash accesses from the CPU. Table 92. SPM Programming Time Symbol Min Programming Time Max Programming Time Flash write (Page Erase, Page 3.7 ms 4.5 ms Write, and write Lock bits by SPM) Simple Assembly Code ;-the routine writes one page of data from RAM to Flash Example for a Boot Loader ; the first data location in RAM is pointed to by the Y pointer ; the first data location in Flash is pointed to by the Z pointer ;-error handling is not included ;-the routine must be placed inside the boot space ; (at least the Do_spm sub routine). Only code inside NRWW section can ; be read during Self-Programming (page erase and page write). ;-registers used: r0, r1, temp1 (r16), temp2 (r17), looplo (r24), ; loophi (r25), spmcrval (r20) ; storing and restoring of registers is not included in the routine ; register usage can be optimized at the expense of code size ;-It is assumed that either the interrupt table is moved to the Boot ; loader section or that the interrupts are disabled. .equ PAGESIZEB = PAGESIZE*2 ;PAGESIZEB is page size in BYTES, not words .org SMALLBOOTSTART Write_page: ; page erase ldi spmcrval, (1<<PGERS) | (1<<SPMEN) rcall Do_spm 233 2502K–AVR–10/06
; re-enable the RWW section ldi spmcrval, (1<<RWWSRE) | (1<<SPMEN) rcall Do_spm ; transfer data from RAM to Flash page buffer ldi looplo, low(PAGESIZEB) ;init loop variable ldi loophi, high(PAGESIZEB) ;not required for PAGESIZEB<=256 Wrloop: ld r0, Y+ ld r1, Y+ ldi spmcrval, (1<<SPMEN) rcall Do_spm adiw ZH:ZL, 2 sbiw loophi:looplo, 2 ;use subi for PAGESIZEB<=256 brne Wrloop ; execute page write subi ZL, low(PAGESIZEB) ;restore pointer sbci ZH, high(PAGESIZEB) ;not required for PAGESIZEB<=256 ldi spmcrval, (1<<PGWRT) | (1<<SPMEN) rcall Do_spm ; re-enable the RWW section ldi spmcrval, (1<<RWWSRE) | (1<<SPMEN) rcall Do_spm ; read back and check, optional ldi looplo, low(PAGESIZEB) ;init loop variable ldi loophi, high(PAGESIZEB) ;not required for PAGESIZEB<=256 subi YL, low(PAGESIZEB) ;restore pointer sbci YH, high(PAGESIZEB) Rdloop: lpm r0, Z+ ld r1, Y+ cpse r0, r1 rjmp Error sbiw loophi:looplo, 1 ;use subi for PAGESIZEB<=256 brne Rdloop ; return to RWW section ; verify that RWW section is safe to read Return: in temp1, SPMCR sbrs temp1, RWWSB ; If RWWSB is set, the RWW section is not ready yet ret ; re-enable the RWW section ldi spmcrval, (1<<RWWSRE) | (1<<SPMEN) rcall Do_spm rjmp Return Do_spm: ; check for previous SPM complete Wait_spm: in temp1, SPMCR sbrc temp1, SPMEN rjmp Wait_spm ; input: spmcrval determines SPM action ; disable interrupts if enabled, store status ATmega8535(L) 234 2502K–AVR–10/06
ATmega8535(L) in temp2, SREG cli ; check that no EEPROM write access is present Wait_ee: sbic EECR, EEWE rjmp Wait_ee ; SPM timed sequence out SPMCR, spmcrval spm ; restore SREG (to enable interrupts if originally enabled) out SREG, temp2 ret ATmega8535 Boot Loader In Table 93 through Table 95, the parameters used in the description of the self pro- Parameters gramming are given. Table 93. Boot Size Configuration(1) Appli- Boot End Boot Reset cation Loader Appli- Address (Start BOOTS BOOTS Boot Flash Flash cation Boot Loader Z1 Z0 Size Pages Section Section Section Section) 128 0x000 - 0xF80 - 1 1 4 0xF7F 0xF80 words 0xF7F 0xFFF 256 0x000 - 0xF00 - 1 0 8 0xEFF 0xF00 words 0xEFF 0xFFF 512 0x000 - 0xE00 - 0 1 16 0xDFF 0xE00 words 0xDFF 0xFFF 1024 0x000 - 0xC00 - 0 0 32 0xBFF 0xC00 words 0xBFF 0xFFF Note: 1. The different BOOTSZ Fuse configurations are shown in Figure 113 Table 94. Read-While-Write Limit(1) Section Pages Address Read-While-Write section (RWW) 96 0x000 - 0xBFF No Read-While-Write section (NRWW) 32 0xC00 - 0xFFF Note: 1. For details about these two section, see “NRWW – No Read-While-Write Section” on page 225 and “RWW – Read-While-Write Section” on page 225 235 2502K–AVR–10/06
Table 95. Explanation of Different Variables used in Figure 114 and the Mapping to the Z-pointer(1) Corresponding Variable Z-value Description 11 Most significant bit in the Program Counter. PCMSB (The Program Counter is 12 bits PC[11:0]) 4 Most significant bit which is used to address PAGEMSB the words within one page (64 words in a page requires five bits PC [4:0]). Z12 Bit in Z-register that is mapped to PCMSB. ZPCMSB Because Z0 is not used, the ZPCMSB equals PCMSB + 1. Z5 Bit in Z-register that is mapped to PCMSB. ZPAGEMSB Because Z0 is not used, the ZPAGEMSB equals PAGEMSB + 1. PC[11:5] Z12:Z6 Program Counter page address: Page select, PCPAGE for Page Erase and Page Write PC[4:0] Z5:Z1 Program Counter word address: Word select, PCWORD for filling temporary buffer (must be zero during page write operation) Note: 1. Z15:Z13: always ignored Z0: should be zero for all SPM commands, byte select for the LPM instruction. See “Addressing the Flash during Self-Programming” on page 229 for details about the use of Z-pointer during Self-Programming. ATmega8535(L) 236 2502K–AVR–10/06
ATmega8535(L) Memory Programming Program And Data The ATmega8535 provides six Lock bits which can be left unprogrammed (“1”) or can Memory Lock Bits be programmed (“0”) to obtain the additional features listed in Table 97. The Lock bits can only be erased to “1” with the Chip Erase command. Table 96. Lock Bit Byte(1) Lock Bit Byte Bit No Description Default Value 7 – 1 (unprogrammed) 6 – 1 (unprogrammed) BLB12 5 Boot Lock bit 1 (unprogrammed) BLB11 4 Boot Lock bit 1 (unprogrammed) BLB02 3 Boot Lock bit 1 (unprogrammed) BLB01 2 Boot Lock bit 1 (unprogrammed) LB2 1 Lock bit 1 (unprogrammed) LB1 0 Lock bit 1 (unprogrammed) Note: 1. “1” means unprogrammed, “0” means programmed Table 97. Lock Bit Protection Modes(2) Memory Lock Bits Protection Type LB Mode LB2 LB1 1 1 1 No memory lock features enabled. Further programming of the Flash and EEPROM is disabled in Parallel and Serial Programming mode. The 2 1 0 Fuse bits are locked in both Serial and Parallel Programming mode.(1) Further programming and verification of the Flash and EEPROM is disabled in Parallel and Serial Programming 3 0 0 mode. The Fuse bits are locked in both Serial and Parallel Programming mode.(1) BLB0 Mode BLB02 BLB01 No restrictions for SPM or LPM accessing the Application 1 1 1 section. 2 1 0 SPM is not allowed to write to the Application section. SPM is not allowed to write to the Application section, and LPM executing from the Boot Loader section is not 3 0 0 allowed to read from the Application section. If interrupt vectors are placed in the Boot Loader section, interrupts are disabled while executing from the Application section. LPM executing from the Boot Loader section is not allowed to read from the Application section. If interrupt 4 0 1 vectors are placed in the Boot Loader section, interrupts are disabled while executing from the Application section. BLB1 Mode BLB12 BLB11 237 2502K–AVR–10/06
Table 97. Lock Bit Protection Modes(2) (Continued) Memory Lock Bits Protection Type No restrictions for SPM or LPM accessing the Boot Loader 1 1 1 section. 2 1 0 SPM is not allowed to write to the Boot Loader section. SPM is not allowed to write to the Boot Loader section, and LPM executing from the Application section is not 3 0 0 allowed to read from the Boot Loader section. If interrupt vectors are placed in the Application section, interrupts are disabled while executing from the Boot Loader section. LPM executing from the Application section is not allowed to read from the Boot Loader section. If interrupt vectors 4 0 1 are placed in the Application section, interrupts are disabled while executing from the Boot Loader section. Notes: 1. Program the Fuse bits before programming the Lock bits. 2. “1” means unprogrammed, “0” means programmed. Fuse Bits The ATmega8535 has two Fuse bytes. Table 98 and Table 99 describe briefly the func- tionality of all the fuses and how they are mapped into the fuse bytes. Note that the fuses are read as logical zero, “0”, if they are programmed. Table 98. Fuse High Byte Fuse High Byte Bit No Description Default Value S8535C 7 Select AT90S8535 compatibility 1 (unprogrammed) mode WDTON 6 WDT always on 1 (unprogrammed, WDT enabled by WDTCR) SPIEN(1) 5 Enable Serial Program and Data 0 (programmed, SPI prog. Downloading enabled) CKOPT(2) 4 Oscillator options 1 (unprogrammed) EESAVE 3 EEPROM memory is preserved 1 (unprogrammed, through the Chip Erase EEPROM not preserved) BOOTSZ1 2 Select Boot Size (see Table 93 for 0 (programmed)(3) details) BOOTSZ0 1 Select Boot Size (see Table 93 for 0 (programmed)(3) details) BOOTRST 0 Select Reset Vector 1 (unprogrammed) Notes: 1. The SPIEN Fuse is not accessible in Serial Programming mode. 2. The CKOPT Fuse functionality depends on the setting of the CKSEL bits. See “Clock Sources” on page 25. for details. 3. The default value of BOOTSZ1..0 results in maximum Boot Size. See Table 93 on page 235. ATmega8535(L) 238 2502K–AVR–10/06
ATmega8535(L) Table 99. Fuse Low Byte Fuse Low Byte Bit no Description Default Value BODLEVEL 7 Brown out detector trigger 1 (unprogrammed) level BODEN 6 Brown out detector enable 1 (unprogrammed, BOD disabled) SUT1 5 Select start-up time 1 (unprogrammed)(1) SUT0 4 Select start-up time 0 (programmed)(1) CKSEL3 3 Select Clock source 0 (programmed)(2) CKSEL2 2 Select Clock source 0 (programmed)(2) CKSEL1 1 Select Clock source 0 (programmed)(2) CKSEL0 0 Select Clock source 1 (unprogrammed)(2) Notes: 1. The default value of SUT1..0 results in maximum start-up time. See Table 10 on page 30 for details. 2. The default setting of CKSEL3..0 results in internal RC Oscillator @ 1 MHz. See Table 2 on page 25 for details. The status of the Fuse bits is not affected by Chip Erase. Note that the Fuse bits are locked if Lock bit 1 (LB1) is programmed. Program the Fuse bits before programming the Lock bits. Latching of Fuses The Fuse values are latched when the device enters Programming mode and changes of the Fuse values will have no effect until the part leaves Programming mode. This does not apply to the EESAVE fuse which will take effect once it is programmed. The fuses are also latched on Power-up in Normal mode. Signature Bytes All Atmel microcontrollers have a three-byte signature code which identifies the device. This code can be read in both Serial and Parallel mode, also when the device is locked. The three bytes reside in a separate address space. For the ATmega8535 the signature bytes are: 1. 0x000: 0x1E (indicates manufactured by Atmel) 2. 0x001: 0x93 (indicates 8 KB Flash memory) 3. 0x002: 0x08 (indicates ATmega8535 device when 0x001 is 0x93) Calibration Byte The ATmega8535 stores four different calibration values for the internal RC Oscillator. These bytes resides in the signature row high byte of the addresses 0x000, 0x0001, 0x0002, and 0x0003 for 1, 2, 4, and 8 MHz respectively. During Reset, the 1 MHz value is automatically loaded into the OSCCAL Register. If other frequencies are used, the calibration value has to be loaded manually, see “Oscillator Calibration Register – OSC- CAL” on page 30 for details. 239 2502K–AVR–10/06
Parallel Programming This section describes how to parallel program and verify Flash Program memory, Parameters, Pin EEPROM Data memory, Memory Lock bits, and Fuse bits in the ATmega8535. Pulses Mapping, and are assumed to be at least 250 ns unless otherwise noted. Commands Signal Names In this section, some pins of the ATmega8535 are referenced by signal names describ- ing their functionality during parallel programming, see Figure 115 and Table 100. Pins not described in the following table are referenced by pin names. The XA1/XA0 pins determine the action executed when the XTAL1 pin is given a posi- tive pulse. The bit coding is shown in Table 102. When pulsing WR or OE, the command loaded determines the action executed. The dif- ferent Commands are shown in Table 103. Figure 115. Parallel Programming +5V RDY/BSY PD1 VCC OE PD2 AVCC WR PD3 PB7 - PB0 DATA BS1 PD4 XA0 PD5 XA1 PD6 PAGEL PD7 +12 V RESET BS2 PA0 XTAL1 GND Table 100. Pin Name Mapping Signal Name in Programming Mode Pin Name I/O Function 0: Device is busy programming, 1: Device is ready RDY/BSY PD1 O for new command OE PD2 I Output Enable (Active low) WR PD3 I Write Pulse (Active low) Byte Select 1 (“0” selects low byte, “1” selects high BS1 PD4 I byte) XA0 PD5 I XTAL Action Bit 0 XA1 PD6 I XTAL Action Bit 1 PAGEL PD7 I Program Memory and EEPROM data Page Load Byte Select 2 (“0” selects low byte, “1” selects 2’nd BS2 PA0 I high byte) DATA PB7 - 0 I/O Bi-directional Data bus (Output when OE is low) ATmega8535(L) 240 2502K–AVR–10/06
ATmega8535(L) Table 101. Pin Values Used to Enter Programming Mode Pin Symbol Value PAGEL Prog_enable[3] 0 XA1 Prog_enable[2] 0 XA0 Prog_enable[1] 0 BS1 Prog_enable[0] 0 Table 102. XA1 and XA0 Coding XA1 XA0 Action when XTAL1 is Pulsed 0 0 Load Flash or EEPROM Address (High or low address byte determined by BS1) 0 1 Load Data (High or Low data byte for Flash determined by BS1) 1 0 Load Command 1 1 No Action, Idle Table 103. Command Byte Bit Coding Command Byte Command Executed 1000 0000 Chip Erase 0100 0000 Write Fuse Bits 0010 0000 Write Lock Bits 0001 0000 Write Flash 0001 0001 Write EEPROM 0000 1000 Read Signature Bytes and Calibration byte 0000 0100 Read Fuse and Lock Bits 0000 0010 Read Flash 0000 0011 Read EEPROM Table 104. No. of Words in a Page and no. of Pages in the Flash Flash Size Page Size PCWORD No. of Pages PCPAGE PCMSB 4K words (8K bytes) 32 words PC[4:0] 128 PC[11:5] 11 Table 105. No. of Words in a Page and no. of Pages in the EEPROM EEPROM Size Page Size PCWORD No. of Pages PCPAGE EEAMSB 512 bytes 4 bytes EEA[1:0] 128 EEA[8:2] 8 241 2502K–AVR–10/06
Parallel Programming Enter Programming Mode The following algorithm puts the device in Parallel Programming mode: 1. Apply 4.5 - 5.5V between V and GND, and wait at least 100 µs. CC 2. Set RESET to “0” and toggle XTAL1 at least six times. 3. Set the Prog_enable pins listed in Table 101 on page 241 to “0000” and wait at least 100 ns. 4. Apply 11.5 - 12.5V to RESET. Any activity on Prog_enable pins within 100 ns after +12V has been applied to RESET, will cause the device to fail entering Pro- gramming mode. Note, if External Crystal or External RC configuration is selected, it may not be possible to apply qualified XTAL1 pulses. In such cases, the following algorithm should be followed: 1. Set Prog_enable pins listed in Table 101 on page 241 to “0000”. 2. Apply 4.5 - 5.5V between V and GND simultaneously as 11.5 - 12.5V is CC applied to RESET. 3. Wait 100 ns. 4. Re-program the fuses to ensure that External Clock is selected as clock source (CKSEL3:0 = 0b0000) If Lock bits are programmed, a Chip Erase command must be executed before changing the fuses. 5. Exit Programming mode by power the device down or by bringing RESET pin to 0b0. 6. Entering Programming mode with the original algorithm, as described above. Considerations for Efficient The loaded command and address are retained in the device during programming. For Programming efficient programming, the following should be considered. (cid:129) The command needs only be loaded once when writing or reading multiple memory locations. (cid:129) Skip writing the data value 0xFF, that is the contents of the entire EEPROM (unless the EESAVE fuse is programmed) and Flash after a Chip Erase. (cid:129) Address high byte needs only be loaded before programming or reading a new 256 word window in Flash or 256 byte EEPROM. This consideration also applies to Signature bytes reading. Chip Erase The Chip Erase will erase the Flash and EEPROM(1) memories plus Lock bits. The Lock bits are not reset until the program memory has been completely erased. The Fuse bits are not changed. A Chip Erase must be performed before the Flash and/or the EEPROM is reprogrammed. Note: 1. The EEPRPOM memory is preserved during Chip Erase if the EESAVE Fuse is programmed. Load Command “Chip Erase” 1. Set XA1, XA0 to “10”. This enables command loading. 2. Set BS1 to “0”. 3. Set DATA to “1000 0000”. This is the command for Chip Erase. 4. Give XTAL1 a positive pulse. This loads the command. 5. Give WR a negative pulse. This starts the Chip Erase. RDY/BSY goes low. 6. Wait until RDY/BSY goes high before loading a new command. ATmega8535(L) 242 2502K–AVR–10/06
ATmega8535(L) Programming the Flash The Flash is organized in pages, see Table 104 on page 241. When programming the Flash, the program data is latched into a page buffer. This allows one page of program data to be programmed simultaneously. The following procedure describes how to pro- gram the entire Flash memory: A. Load Command “Write Flash” 1. Set XA1, XA0 to “10”. This enables command loading. 2. Set BS1 to “0”. 3. Set DATA to “0001 0000”. This is the command for Write Flash. 4. Give XTAL1 a positive pulse. This loads the command. B. Load Address Low byte 1. Set XA1, XA0 to “00”. This enables address loading. 2. Set BS1 to “0”. This selects low address. 3. Set DATA = Address low byte (0x00 - 0xFF). 4. Give XTAL1 a positive pulse. This loads the address low byte. C. Load Data Low Byte 1. Set XA1, XA0 to “01”. This enables data loading. 2. Set DATA = Data low byte (0x00 - 0xFF). 3. Give XTAL1 a positive pulse. This loads the data byte. D. Load Data High Byte 1. Set BS1 to “1”. This selects high data byte. 2. Set XA1, XA0 to “01”. This enables data loading. 3. Set DATA = Data high byte (0x00 - 0xFF). 4. Give XTAL1 a positive pulse. This loads the data byte. E. Latch Data 1. Set BS1 to “1”. This selects high data byte. 2. Give PAGEL a positive pulse. This latches the data bytes. (See Figure 117 for signal waveforms.) F. Repeat B through E until the entire buffer is filled or until all data within the page is loaded. While the lower bits in the address are mapped to words within the page, the higher bits address the pages within the FLASH. This is illustrated in Figure 116 on page 244. Note that if less than eight bits are required to address words in the page (pagesize < 256), the most significant bit(s) in the address low byte are used to address the page when performing a page write. G. Load Address High byte 1. Set XA1, XA0 to “00”. This enables address loading. 2. Set BS1 to “1”. This selects high address. 3. Set DATA = Address high byte (0x00 - 0xFF). 4. Give XTAL1 a positive pulse. This loads the address high byte. H. Program Page 1. Set BS1 to “0”. 2. Give WR a negative pulse. This starts programming of the entire page of data. RDY/BSY goes low. 243 2502K–AVR–10/06
3. Wait until RDY/BSY goes high. (See Figure 117 for signal waveforms) I. Repeat B through H until the entire Flash is programmed or until all data has been programmed. J. End Page Programming 1. 1. Set XA1, XA0 to “10”. This enables command loading. 2. Set DATA to “0000 0000”. This is the command for No Operation. 3. Give XTAL1 a positive pulse. This loads the command, and the internal write sig- nals are reset. Figure 116. Addressing the Flash which is Organized in Pages(1) PCMSB PAGEMSB PROGRAM PCPAGE PCWORD COUNTER PAGE ADDRESS WORD ADDRESS WITHIN THE FLASH WITHIN A PAGE PROGRAM MEMORY PAGE PCWORD[PAGEMSB:0]: PAGE INSTRUCTION WORD 00 01 02 PAGEEND Note: 1. PCPAGE and PCWORD are listed in Table 104 on page 241. Figure 117. Programming the Flash Waveforms(1) F A B C D E B C D E G H DATA 0x10 ADDR. LOW DATA LOW DATA HIGH XX ADDR. LOW DATA LOW DATA HIGH XX ADDR. HIGH XX XA1 XA0 BS1 XTAL1 WR RDY/BSY RESET +12V OE PAGEL BS2 Note: 1. “XX” is don’t care. The letters refer to the programming description above. ATmega8535(L) 244 2502K–AVR–10/06
ATmega8535(L) Programming the EEPROM The EEPROM is organized in pages, see Table 105 on page 241. When programming the EEPROM, the program data is latched into a page buffer. This allows one page of data to be programmed simultaneously. The programming algorithm for the EEPROM data memory is as follows (refer to “Programming the Flash” on page 243 for details on Command, Address and Data loading): 1. A: Load Command “0001 0001”. 2. G: Load Address High Byte (0x00 - 0xFF). 3. B: Load Address Low Byte (0x00 - 0xFF). 4. C: Load Data (0x00 - 0xFF). 5. E: Latch data (give PAGEL a positive pulse). K: Repeat 3 through 5 until the entire buffer is filled. L: Program EEPROM page. 1. Set BS1 to “0”. 2. Give WR a negative pulse. This starts programming of the EEPROM page. RDY/BSY goes low. 3. Wait until to RDY/BSY goes high before programming the next page. (See Figure 118 for signal waveforms.) Figure 118. Programming the EEPROM Waveforms K A G B C E B C E L DATA 0x11 ADDR. HIGH ADDR. LOW DATA XX ADDR. LOW DATA XX XA1 XA0 BS1 XTAL1 WR RDY/BSY RESET +12V OE PAGEL BS2 Reading the Flash The algorithm for reading the Flash memory is as follows (refer to “Programming the Flash” on page 243 for details on Command and Address loading): 1. A: Load Command “0000 0010”. 2. G: Load Address High Byte (0x00 - 0xFF). 3. B: Load Address Low Byte (0x00 - 0xFF). 4. Set OE to “0”, and BS1 to “0”. The Flash word low byte can now be read at DATA. 5. Set BS1 to “1”. The Flash word high byte can now be read at DATA. 6. Set OE to “1”. 245 2502K–AVR–10/06
Reading the EEPROM The algorithm for reading the EEPROM memory is as follows (refer to “Programming the Flash” on page 243 for details on Command and Address loading): 1. A: Load Command “0000 0011”. 2. G: Load Address High Byte (0x00 - 0xFF). 3. B: Load Address Low Byte (0x00 - 0xFF). 4. Set OE to “0”, and BS1 to “0”. The EEPROM Data byte can now be read at DATA. 5. Set OE to “1”. Programming the Fuse Low The algorithm for programming the Fuse Low bits is as follows (refer to “Programming Bits the Flash” on page 243 for details on Command and Data loading): 1. A: Load Command “0100 0000”. 2. C: Load Data Low Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit. 3. Set BS1 to “0” and BS2 to “0”. This selects low data byte. 4. Give WR a negative pulse and wait for RDY/BSY to go high. Programming the Fuse High The algorithm for programming the Fuse high bits is as follows (refer to “Programming Bits the Flash” on page 243 for details on Command and Data loading): 1. A: Load Command “0100 0000”. 2. C: Load Data Low Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit. 3. Set BS1 to “1” and BS2 to “0”. This selects high data byte. 4. Give WR a negative pulse and wait for RDY/BSY to go high. 5. Set BS1 to “0”. This selects low data byte. Figure 119. Programming the Fuses Waveforms Write Fuse Low byte Write Fuse High byte A C A C DATA $40 DATA XX $40 DATA XX XA1 XA0 BS1 XTAL1 WR RDY/BSY RESET +12V OE PAGEL BS2 ATmega8535(L) 246 2502K–AVR–10/06
ATmega8535(L) Programming the Lock Bits The algorithm for programming the Lock bits is as follows (refer to “Programming the Flash” on page 243 for details on Command and Data loading): 1. A: Load Command “0010 0000”. 2. C: Load Data Low Byte. Bit n = “0” programs the Lock bit. 3. Give WR a negative pulse and wait for RDY/BSY to go high. The Lock bits can only be cleared by executing Chip Erase. Reading the Fuse and Lock The algorithm for reading the Fuse and Lock bits is as follows (refer to “Programming Bits the Flash” on page 243 for details on Command loading): 1. A: Load Command “0000 0100”. 2. Set OE to “0”, BS2 to “0”, and BS1 to “0”. The status of the Fuse Low bits can now be read at DATA (“0” means programmed). 3. Set OE to “0”, BS2 to “1”, and BS1 to “1”. The status of the Fuse High bits can now be read at DATA (“0” means programmed). 4. Set OE to “0”, BS2 to “0”, and BS1 to “1”. The status of the Lock bits can now be read at DATA (“0” means programmed). 5. Set OE to “1”. Figure 120. Mapping Between BS1, BS2 and the Fuse- and Lock Bits During Read Fuse Low Byte 0 DATA 1 Lock Bits 0 BS1 Fuse High Byte 1 BS2 Reading the Signature Bytes The algorithm for reading the Signature bytes is as follows (refer to “Programming the Flash” on page 243 for details on Command and Address loading): 1. A: Load Command “0000 1000”. 2. B: Load Address Low Byte (0x00 - 0x02). 3. Set OE to “0”, and BS to “0”. The selected Signature byte can now be read at DATA. 4. Set OE to “1”. Reading the Calibration Byte The algorithm for reading the Calibration byte is as follows (refer to “Programming the Flash” on page 243 for details on Command and Address loading): 1. A: Load Command “0000 1000”. 2. B: Load Address Low Byte, 0x00. 3. Set OE to “0”, and BS1 to “1”. The Calibration byte can now be read at DATA. 4. Set OE to “1”. 247 2502K–AVR–10/06
Parallel Programming Figure 121. Parallel Programming Timing, Including some General Timing Characteristics Requirements t XLWL t XTAL1 XHXL t t DVXH XLDX Data & Contol (DATA, XA0/1, BS1, BS2) t t t BVPH PLBX BVWL t WLBX PAGEL t PHPL t WLWH WR t PLWL WLRL RDY/BSY t WLRH Figure 122. Parallel Programming Timing, Loading Sequence with Timing Requirements(1) LOAD ADDRESS LOAD DATA LOAD DATA LOAD DATA LOAD ADDRESS (LOW BYTE) (LOW BYTE) (HIGH BYTE) (LOW BYTE) tXLXH tXLPH tPLXH XTAL1 BS1 PAGEL DATA ADDR0 (low byte) DATA (low byte) DATA (high byte) ADDR1 (low byte) XA0 XA1 Note: 1. The timing requirements shown in Figure 121 (i.e. t , t , and t ) also apply DVXH XHXL XLDX to loading operation. ATmega8535(L) 248 2502K–AVR–10/06
ATmega8535(L) Figure 123. Parallel Programming Timing, Reading Sequence (within the same Page) with Timing Requirements(1) LOAD ADDRESS READ DATA READ DATA LOAD ADDRESS (LOW BYTE) (LOW BYTE) (HIGH BYTE) (LOW BYTE) tXLOL XTAL1 tBVDV BS1 tOLDV OE tOHDZ DATA ADDR0 (low byte) DATA (low byte) DATA (high byte) ADDR1 (low byte) XA0 XA1 Note: 1. The timing requirements shown in Figure 121 (i.e. t , t , and t ) also apply DVXH XHXL XLDX to reading operation. 249 2502K–AVR–10/06
Table 106. Parallel Programming Characteristics, V = 5V ± 10% CC Symbol Parameter Min Typ Max Units V Programming Enable Voltage 11.5 12.5 V PP I Programming Enable Current 250 μA PP t Data and Control Valid before XTAL1 High 67 ns DVXH t XTAL1 Low to XTAL1 High 200 ns XLXH t XTAL1 Pulse Width High 150 ns XHXL t Data and Control Hold after XTAL1 Low 67 ns XLDX t XTAL1 Low to WR Low 0 ns XLWL t XTAL1 Low to PAGEL High 0 ns XLPH t PAGEL low to XTAL1 High 150 ns PLXH t BS1 Valid before PAGEL High 67 ns BVPH t PAGEL Pulse Width High 150 ns PHPL t BS1 Hold after PAGEL Low 67 ns PLBX t BS2/1 Hold after WR Low 67 ns WLBX t PAGEL Low to WR Low 67 ns PLWL t BS1 Valid to WR Low 67 ns BVWL t WR Pulse Width Low 150 ns WLWH t WR Low to RDY/BSY Low 0 1 μs WLRL t WR Low to RDY/BSY High(1) 3.7 4.5 ms WLRH t WR Low to RDY/BSY High for Chip Erase(2) 7.5 9 ms WLRH_CE t XTAL1 Low to OE Low 0 ns XLOL t BS1 Valid to DATA Valid 0 250 ns BVDV t OE Low to DATA Valid 250 ns OLDV t OE High to DATA Tri-stated 250 ns OHDZ Notes: 1. t is valid for the Write Flash, Write EEPROM, Write Fuse bits and Write Lock WLRH bits commands. 2. t is valid for the Chip Erase command. WLRH_CE ATmega8535(L) 250 2502K–AVR–10/06
ATmega8535(L) Serial Downloading Both the Flash and EEPROM memory arrays can be programmed using the serial SPI bus while RESET is pulled to GND. The serial interface consists of pins SCK, MOSI (input), and MISO (output). After RESET is set low, the Programming Enable instruction needs to be executed first before program/erase operations can be executed. NOTE, in Table 107 on page 251, the pin mapping for SPI programming is listed. Not all parts use the SPI pins dedicated for the internal SPI interface. Serial Programming Pin Table 107. Pin Mapping Serial Programming Mapping Symbol Pins I/O Description MOSI PB5 I Serial Data in MISO PB6 O Serial Data out SCK PB7 I Serial Clock Figure 124. Serial Programming and Verify(1) 2.7 - 5.5V VCC 2.7 - 5.5V(2) MOSI PB5 MISO PB6 AVCC SCK PB7 XTAL1 RESET GND Notes: 1. If the device is clocked by the Internal Oscillator, it is no need to connect a clock source to the XTAL1 pin. 2. VCC - 0.3 < AVCC < VCC + 0.3. However, AVCC should always be within 2.7 - 5.5V. When programming the EEPROM, an auto-erase cycle is built into the self-timed pro- gramming operation (in the Serial mode ONLY) and there is no need to first execute the Chip Erase instruction. The Chip Erase operation turns the content of every memory location in both the Program and EEPROM arrays into 0xFF. Depending on CKSEL Fuses, a valid clock must be present. The minimum low and high periods for the serial clock (SCK) input are defined as follows: Low:> 2 CPU clock cycles for f < 12 MHz, 3 CPU clock cycles for f ≥ 12 MHz ck ck High:> 2 CPU clock cycles for f < 12 MHz, 3 CPU clock cycles for f ≥ 12 MHz ck ck 251 2502K–AVR–10/06
Serial Programming When writing serial data to the ATmega8535, data is clocked on the rising edge of SCK. Algorithm When reading data from the ATmega8535, data is clocked on the falling edge of SCK. See Figure 125 for timing details. To program and verify the ATmega8535 in the Serial Programming mode, the following sequence is recommended (See four byte instruction formats in Table 109): 1. Power-up sequence: Apply power between V and GND while RESET and SCK are set to “0”. In CC some systems, the programmer can not guarantee that SCK is held low during Power-up. In this case, RESET must be given a positive pulse of at least two CPU clock cycles duration after SCK has been set to “0”. 2. Wait for at least 20 ms and enable serial programming by sending the Program- ming Enable serial instruction to pin MOSI. 3. The serial programming instructions will not work if the communication is out of synchronization. When in synchronization the second byte (0x53), will echo back when issuing the third byte of the Programming Enable instruction. Whether the echo is correct or not, all four bytes of the instruction must be transmitted. If the 0x53 did not echo back, give RESET a positive pulse and issue a new Program- ming Enable command. 4. The Flash is programmed one page at a time. The page size is found in Table 104 on page 241. The memory page is loaded one byte at a time by supplying the 6 LSB of the address and data together with the Load Program Memory Page instruction. To ensure correct loading of the page, the data low byte must be loaded before data high byte is applied for a given address. The Program Memory Page is stored by loading the Write Program Memory Page instruction with the 8 MSB of the address. If polling is not used, the user must wait at least t before issuing the next page. (See Table 108.) Accessing the serial WD_FLASH programming interface before the Flash write operation completes can result in incorrect programming. 5. The EEPROM array is programmed one byte at a time by supplying the address and data together with the appropriate Write instruction. An EEPROM memory location is first automatically erased before new data is written. If polling is not used, the user must wait at least t before issuing the next byte. (See WD_EEPROM Table 108). In a chip erased device, no 0xFFs in the data file(s) need to be programmed. 6. Any memory location can be verified by using the Read instruction which returns the content at the selected address at serial output MISO. 7. At the end of the programming session, RESET can be set high to commence normal operation. 8. Power-off sequence (if needed): Set RESET to “1”. Turn V power off. CC Data Polling Flash When a page is being programmed into the Flash, reading an address location within the page being programmed will give the value 0xFF. At the time the device is ready for a new page, the programmed value will read correctly. This is used to determine when the next page can be written. Note that the entire page is written simultaneously and any address within the page can be used for polling. Data polling of the Flash will not work for the value 0xFF, so when programming this value, the user will have to wait for at least t before programming the next page. As a chip erased device contains WD_FLASH 0xFF in all locations, programming of addresses that are meant to contain 0xFF, can be skipped. See Table 108 for t value. WD_FLASH ATmega8535(L) 252 2502K–AVR–10/06
ATmega8535(L) Data Polling EEPROM When a new byte has been written and is being programmed into EEPROM, reading the address location being programmed will give the value 0xFF. At the time the device is ready for a new byte, the programmed value will read correctly. This is used to deter- mine when the next byte can be written. This will not work for the value 0xFF, but the user should have the following in mind: As a chip erased device contains 0xFF in all locations, programming of addresses that are meant to contain 0xFF, can be skipped. This does not apply if the EEPROM is reprogrammed without chip erasing the device. In this case, data polling cannot be used for the value 0xFF, and the user will have to wait at least t before programming the next byte. See Table 108 for t WD_EEPROM WD_EEPROM value. Table 108. Minimum Wait Delay Before Writing the Next Flash or EEPROM Location Symbol Minimum Wait Delay t 4.5 ms WD_FLASH t 9.0 ms WD_EEPROM t 9.0 ms WD_ERASE t 4.5 ms WD_FUSE Figure 125. Serial Programming Waveforms SERIAL DATA INPUT MSB LSB (MOSI) SERIAL DATA OUTPUT MSB LSB (MISO) SERIAL CLOCK INPUT (SCK) SAMPLE 253 2502K–AVR–10/06
Table 109. Serial Programming Instruction Set a = address high bits, b = address low bits, H = 0 - Low byte, 1 - High Byte, o = data out, i = data in, x = don’t care Instruction Format Instruction Byte 1 Byte 2 Byte 3 Byte4 Operation 1010 1100 0101 0011 xxxx xxxx xxxx xxxx Enable Serial Programming after Programming Enable RESET goes low. Chip Erase 1010 1100 100x xxxx xxxx xxxx xxxx xxxx Chip Erase EEPROM and Flash. 0010 H000 0000 aaaa bbbb bbbb oooo oooo Read H (high or low) data o from Read Program Memory Program memory at word address a:b. 0100 H000 0000 xxxx xxxb bbbb iiii iiii Write H (high or low) data i to Program Memory page at word Load Program Memory address b. Data low byte must be Page loaded before Data high byte is applied within the same address. Write Program Memory 0100 1100 0000 aaaa bbbx xxxx xxxx xxxx Write Program Memory Page at Page address a:b. 1010 0000 00xx xxxa bbbb bbbb oooo oooo Read data o from EEPROM Read EEPROM Memory memory at address a:b. 1100 0000 00xx xxxa bbbb bbbb iiii iiii Write data i to EEPROM memory Write EEPROM Memory at address a:b. 0101 1000 0000 0000 xxxx xxxx xxoo oooo Read Lock bits. “0” = programmed, Read Lock Bits “1” = unprogrammed. See Table 96 on page 237 for details. 1010 1100 111x xxxx xxxx xxxx 11ii iiii Write Lock bits. Set bits = “0” to Write Lock Bits program Lock bits. See Table 96 on page 237 for details. 0011 0000 00xx xxxx xxxx xxbb oooo oooo Read Signature Byte o at address Read Signature Byte b. 1010 1100 1010 0000 xxxx xxxx iiii iiii Set bits = “0” to program, “1” to Write Fuse Bits unprogram. See Table 99 on page 239 for details. 1010 1100 1010 1000 xxxx xxxx iiii iiii Set bits = “0” to program, “1” to Write Fuse High Bits unprogram. See Table 98 on page 238 for details. 0101 0000 0000 0000 xxxx xxxx oooo oooo Read Fuse bits. “0” = programmed, Read Fuse Bits “1” = unprogrammed. See Table 99 on page 239 for details. 0101 1000 0000 1000 xxxx xxxx oooo oooo Read Fuse high bits. “0” = pro- grammed, “1” = unprogrammed. Read Fuse High Bits See Table 98 on page 238 for details. Read Calibration Byte 0011 1000 00xx xxxx 0000 00bb oooo oooo Read Calibration Byte SPI Serial Programming For characteristics of the SPI module, see “SPI Timing Characteristics” on page 261. Characteristics ATmega8535(L) 254 2502K–AVR–10/06
ATmega8535(L) Electrical Characteristics Absolute Maximum Ratings* Operating Temperature..................................-55°C to +125°C *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent dam- Storage Temperature.....................................-65°C to +150°C age to the device. This is a stress rating only and functional operation of the device at these or Voltage on any Pin except RESET other conditions beyond those indicated in the with respect to Ground................................-0.5V to V +0.5V operational sections of this specification is not CC implied. Exposure to absolute maximum rating Voltage on RESET with respect to Ground......-0.5V to +13.0V conditions for extended periods may affect device reliability. Maximum Operating Voltage............................................6.0V DC Current per I/O Pin...............................................40.0 mA DC Current V and GND Pins........................200.0 PDIP og CC 400 mA TQFP/MLF/PLCCmA DC Characteristics T = -40°C to 85°C, V = 2.7V to 5.5V (unless otherwise noted) A CC Symbol Parameter Condition Min Typ Max Units Input Low Voltage except V V =2.7V - 5.5V -0.5 0.2 V (1) V IL XTAL1 and RESET pins CC CC Input High Voltage except V V =2.7V - 5.5V 0.6 V (2) V + 0.5 V IH XTAL1 and RESET pins CC CC CC Input Low Voltage V V =2.7V - 5.5V -0.5 0.1 V (1) V IL1 XTAL1 pin CC CC Input High Voltage XTAL1 V V =2.7V - 5.5V 0.8 V (2) V + 0.5 V IH1 pin CC CC CC Input Low Voltage RESET V V =2.7V - 5.5V -0.5 0.2 V V IL2 pin CC CC Input High Voltage V V =2.7V - 5.5V 0.9 V (2) V + 0.5 V IH2 RESET pin CC CC CC Output Low Voltage(3) I = 20 mA, V = 5V 0.7 V V OL CC OL (Ports A,B,C,D) I = 10 mA, V = 3V 0.5 V OL CC Output High Voltage(4) I = -20 mA, V = 5V 4.2 V V OH CC OH (Ports A,B,C,D) I = -10 mA, V = 3V 2.2 V OH CC Input Leakage V = 5.5V, pin low I CC 1 µA IL Current I/O Pin (absolute value) Input Leakage V = 5.5V, pin high I CC 1 µA IH Current I/O Pin (absolute value) R Reset Pull-up Resistor 30 60 kΩ RST R I/O Pin Pull-up Resistor 20 50 kΩ pu 255 2502K–AVR–10/06
T = -40°C to 85°C, V = 2.7V to 5.5V (unless otherwise noted) (Continued) A CC Symbol Parameter Condition Min Typ Max Units Active 4 MHz, V = 3V CC 4 mA (ATmega8535L) Active 8 MHz, V = 5V CC 14 mA (ATmega8535) Power Supply Current Idle 4 MHz, V = 3V I CC 3 mA CC (ATmega8535L) Idle 8 MHz, V = 5V CC 10 mA (ATmega8535) WDT enabled, V = 3V < 10 µA Power-down mode(5) CC WDT disabled, V = 3V < 3 µA CC Analog Comparator V = 5V V CC 40 mV ACIO Input Offset Voltage V = V /2 in CC Analog Comparator V = 5V I CC -50 50 nA ACLK Input Leakage Current V = V /2 in CC Analog Comparator V = 2.7V 750 t CC ns ACPD Propagation Delay V = 4.0V 500 CC Notes: 1. “Max” means the highest value where the pin is guaranteed to be read as low. 2. “Min” means the lowest value where the pin is guaranteed to be read as high. 3. Although each I/O port can sink more than the test conditions (20mA at V = 5V, 10mA at V = 3V) under steady state CC CC conditions (non-transient), the following must be observed: PDIP Package: 1] The sum of all IOL, for all ports, should not exceed 200 mA. 2] The sum of all IOL, for port A0 - A7, should not exceed 100 mA. 3] The sum of all IOL, for ports B0 - B7,C0 - C7, D0 - D7 and XTAL2, should not exceed 100 mA. PLCC/MLF/TQFP Package: 1] The sum of all IOL, for all ports, should not exceed 400 mA. 2] The sum of all IOL, for ports A0 - A7, should not exceed 100 mA. 3] The sum of all IOL, for ports B0 - B3, should not exceed 100 mA. 4] The sum of all IOL, for ports B4 - B7, should not exceed 100 mA. 5] The sum of all IOL, for ports C0 - C3, should not exceed 100 mA. 6] The sum of all IOL, for ports C4 - C7, should not exceed 100 mA. 7] The sum of all IOL, for ports D0 - D3 and XTAL2, should not exceed 100 mA. 8] The sum of all IOL, for ports D4 - D7, should not exceed 100 mA. If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test condition. 4. Although each I/O port can source more than the test conditions (20mA at V = 5V, 10mA at V = 3V) under steady state CC CC conditions (non-transient), the following must be observed: PDIP Package: 1] The sum of all IOH, for all ports, should not exceed 200 mA. 2] The sum of all IOH, for port A0 - A7, should not exceed 100 mA. 3] The sum of all IOH, for ports B0 - B7,C0 - C7, D0 - D7 and XTAL2, should not exceed 100 mA. PLCC/MLF/TQFP Package: 1] The sum of all IOH, for all ports, should not exceed 400 mA. 2] The sum of all IOH, for ports A0 - A7, should not exceed 100 mA. 3] The sum of all IOH, for ports B0 - B3, should not exceed 100 mA. 4] The sum of all IOH, for ports B4 - B7, should not exceed 100 mA. 5] The sum of all IOH, for ports C0 - C3, should not exceed 100 mA. 6] The sum of all IOH, for ports C4 - C7, should not exceed 100 mA. 7] The sum of all IOH, for ports D0 - D3 and XTAL2, should not exceed 100 mA. 8] The sum of all IOH, for ports D4 - D7, should not exceed 100 mA ATmega8535(L) 256 2502K–AVR–10/06
ATmega8535(L) If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current greater than the listed test condition. 5. Minimum V for Power-down is 2.5V. CC 257 2502K–AVR–10/06
External Clock Drive Figure 126. External Clock Drive Waveforms Waveforms V IH1 V IL1 External Clock Drive Table 110. External Clock Drive V = 2.7V to 5.5V V = 4.5V to 5.5V CC CC Symbol Parameter Min Max Min Max Units 1/t Oscillator Frequency 0 8 0 16 MHz CLCL t Clock Period 125 62.5 ns CLCL t High Time 50 25 ns CHCX t Low Time 50 25 ns CLCX t Rise Time 1.6 0.5 μs CLCH t Fall Time 1.6 0.5 μs CHCL Change in period from one clock cycle to the 2 2 % Δt next CLCL Table 111. External RC Oscillator, Typical Frequencies R [kΩ](1) C [pF] f(2) 33 22 650 kHz 10 22 2.0 MHz Notes: 1. R should be in the range 3 kΩ - 100 kΩ, and C should be at least 20 pF. The C values given in the table includes pin capacitance. This will vary with package type. 2. The frequency will vary with package type and board layout. ATmega8535(L) 258 2502K–AVR–10/06
ATmega8535(L) Two-wire Serial Interface Characteristics Table 112 describes the requirements for devices connected to the Two-wire Serial Bus. The ATmega8535 Two-wire Serial Interface meets or exceeds these requirements under the noted conditions. Timing symbols refer to Figure 127. Table 112. Two-wire Serial Bus Requirements Symbol Parameter Condition Min Max Units Input Low Voltage -0.5 0.3 V V VIL CC Input High Voltage 0.7 V V + 0.5 V VIH CC CC (1) Hysteresis of Schmitt Trigger Inputs 0.05 V (2) – V Vhys CC (1) Output Low Voltage 3 mA sink current 0 0.4 V VOL (1) Rise Time for both SDA and SCL 20 + 0.1C (3)(2) 300 ns tr b (1) Output Fall Time from V to V 10 pF < C < 400 pF(3) 20 + 0.1C (3)(2) 250 ns tof IHmin ILmax b b (1) Spikes Suppressed by Input Filter 0 50(2) ns tSP I Input Current each I/O Pin 0.1V < V < 0.9V -10 10 µA i CC i CC C(1) Capacitance for each I/O Pin – 10 pF i f SCL Clock Frequency f (4) > max(16f , 250kHz)(5) 0 400 kHz SCL CK SCL fSCL ≤ 100 kHz -V---C----C----–-----0---.--4---V--- 1----0---0----0---n---s-- Ω 3mA C b Rp Value of Pull-up resistor fSCL > 100 kHz -V---C----C----–-----0---.--4---V--- 3----0---0----n---s-- Ω 3mA C b f ≤ 100 kHz 4.0 – µs SCL t Hold Time (Repeated) START Condition HD;STA f > 100 kHz 0.6 – µs SCL f ≤ 100 kHz(6) 4.7 – µs SCL t Low Period of the SCL Clock LOW f > 100 kHz(7) 1.3 – µs SCL f ≤ 100 kHz 4.0 – µs SCL t High Period of the SCL clock HIGH f > 100 kHz 0.6 – µs SCL Set-up Time for a Repeated START fSCL ≤ 100 kHz 4.7 – µs t SU;STA Condition f > 100 kHz 0.6 – µs SCL f ≤ 100 kHz 0 3.45 µs SCL t Data hoLd Time HD;DAT f > 100 kHz 0 0.9 µs SCL f ≤ 100 kHz 250 – ns SCL t Data Setup Time SU;DAT f > 100 kHz 100 – ns SCL f ≤ 100 kHz 4.0 – µs SCL t Setup Time for STOP Condition SU;STO f > 100 kHz 0.6 – µs SCL Bus Free Time between a STOP and START fSCL ≤ 100 kHz 4.7 – µs t BUF Condition f > 100 kHz 1.3 – µs SCL Notes: 1. In ATmega8535, this parameter is characterized and not 100% tested. 2. Required only for f > 100 kHz. SCL 3. C = capacitance of one bus line in pF. b 259 2502K–AVR–10/06
4. f = CPU clock frequency. CK 5. This requirement applies to all ATmega8535 Two-wire Serial Interface operation. Other devices connected to the Two-wire Serial Bus need only obey the general f requirement. SCL 6. The actual low period generated by the ATmega8535 Two-wire Serial Interface is (1/f - 2/f ), thus f must be greater SCL CK CK than 6 MHz for the low time requirement to be strictly met at f = 100 kHz. SCL 7. The actual low period generated by the ATmega8535 Two-wire Serial Interface is (1/f - 2/f ), thus the low time require- SCL CK ment will not be strictly met for f > 308 kHz when f = 8 MHz. Still, ATmega8535 devices connected to the bus may SCL CK communicate at full speed (400 kHz) with other ATmega8535 devices, as well as any other device with a proper t accep- LOW tance margin. Figure 127. Two-wire Serial Bus Timing tof tHIGH tr t t LOW LOW SCL tSU;STA tHD;STA tHD;DAT tSU;DAT t SU;STO SDA t BUF ATmega8535(L) 260 2502K–AVR–10/06
ATmega8535(L) SPI Timing See Figure 128 and Figure 129 for details. Characteristics Table 113. SPI Timing Parameters Description Mode Min Typ Max 1 SCK period Master See Table 59 2 SCK high/low Master 50% duty cycle 3 Rise/Fall time Master 3.6 4 Setup Master 10 5 Hold Master 10 6 Out to SCK Master 5 (cid:129) t ns SCK 7 SCK to out Master 10 8 SCK to out high Master 10 9 SS low to out Slave 15 10 SCK period Slave 4 (cid:129) t ck 11 SCK high/low Slave 2 (cid:129) t ck 12 Rise/Fall time Slave 1.6 ns 13 Setup Slave 10 14 Hold Slave 10 15 SCK to out Slave 15 ns 16 SCK to SS high Slave 20 17 SS high to tri-state Slave 10 18 SS low to SCK Slave 2 (cid:129) t ck 261 2502K–AVR–10/06
Figure 128. SPI Interface Timing Requirements (Master Mode) SS 6 1 SCK (CPOL = 0) 2 2 SCK (CPOL = 1) 4 5 3 MISO MSB ... LSB (Data Input) 7 8 MOSI MSB ... LSB (Data Output) Figure 129. SPI Interface Timing Requirements (Slave Mode) 18 SS 10 16 9 SCK (CPOL = 0) 11 11 SCK (CPOL = 1) 13 14 12 MOSI MSB ... LSB (Data Input) 15 17 MISO MSB ... LSB X (Data Output) ATmega8535(L) 262 2502K–AVR–10/06
ATmega8535(L) ADC Characteristics Table 114. ADC Characteristics, Single Ended Channels Symbol Parameter Condition Min(1) Typ(1) Max(1) Units Resolution Single Ended Conversion 10 Bits Single Ended Conversion V = 4V, V = 4V 1.5 LSB REF CC ADC clock = 200 kHz Single Ended Conversion V = 4V, V = 4V 3 LSB REF CC ADC clock = 1 MHz Absolute Accuracy Single Ended Conversion (Including INL, DNL, Quantization Error, Gain V = 4V, V = 4V and Offset Error) REF CC 1.5 LSB ADC clock = 200 kHz Noise Reduction mode Single Ended Conversion V = 4V, V = 4V REF CC 3 LSB ADC clock = 1 MHz Noise Reduction mode Single Ended Conversion Integral Non-Linearity (INL) V = 4V, V = 4V 0.75 LSB REF CC ADC clock = 200 kHz Single Ended Conversion Differential Non-Linearity (DNL) V = 4V, V = 4V 0.25 LSB REF CC ADC clock = 200 kHz Single Ended Conversion Gain Error V = 4V, V = 4V 0.75 LSB REF CC ADC clock = 200 kHz Single Ended Conversion Offset error V = 4V, V = 4V 0.75 LSB REF CC ADC clock = 200 kHz Clock Frequency 50 1000 kHz Conversion Time 13 260 µs AVCC Analog Supply Voltage V - 0.3(2) V + 0.3(3) V CC CC V Reference Voltage 2.0 AVCC V REF V Input Voltage GND V V IN REF ADC Conversion Output 0 1023 LSB Input Bandwidth 38.5 kHz V Internal Voltage Reference 2.3 2.56 2.7 V INT R Reference Input Resistance 32 kΩ REF R Analog Input Resistance 100 MΩ AIN Notes: 1. Values are guidelines only. 2. Minimum for AV is 2.7V. CC 3. Maximum for AV is 5.5V CC 263 2502K–AVR–10/06
Table 115. ADC Characteristics, Differential Channels Symbol Parameter Condition Min(1) Typ(1) Max(1) Units Gain = 1x 10 Bits Resolution Gain = 10x 10 Bits Gain = 200x 10 Bits Gain = 1x V = 4V, V = 5V 18 LSB REF CC ADC clock = 50 - 200 kHz Gain = 10x Absolute Accuracy V = 4V, V = 5V 18 LSB REF CC ADC clock = 50 - 200 kHz Gain = 200x V = 4V, V = 5V 6 LSB REF CC ADC clock = 50 - 200 kHz Gain = 1x V = 4V, V = 5V 0.75 LSB REF CC ADC clock = 50 - 200 kHz Integral Non-Linearity (INL) Gain = 10x (Accuracy after Calibration for Offset and V = 4V, V = 5V 0.75 LSB REF CC Gain Error) ADC clock = 50 - 200 kHz Gain = 200x V = 4V, V = 5V 3.5 LSB REF CC ADC clock = 50 - 200 kHz Gain = 1x 1.7 % Gain Error Gain = 10x 1.6 % Gain = 200x 0.3 % Gain = 1x V = 4V, V = 5V 2 LSB REF CC ADC clock = 50 - 200 kHz Gain = 10x Offset Error V = 4V, V = 5V 2.5 LSB REF CC ADC clock = 50 - 200 kHz Gain = 200x V = 4V, V = 5V 3.5 LSB REF CC ADC clock = 50 - 200 kHz Clock Frequency 50 200 kHz Conversion Time 65 260 µs AVCC Analog Supply Voltage V - 0.3(2) V + 0.3(3) V CC CC V Reference Voltage 2.0 AVCC- 0.5 V REF V Input Voltage GND V V IN CC V Input Differential Voltage -V /Gain V /Gain V DIFF REF REF ADC Conversion Output -511 511 LSB Input Bandwidth 4 kHz ATmega8535(L) 264 2502K–AVR–10/06
ATmega8535(L) Table 115. ADC Characteristics, Differential Channels (Continued) Symbol Parameter Condition Min(1) Typ(1) Max(1) Units V Internal Voltage Reference 2.3 2.56 2.7 V INT R Reference Input Resistance 32 kΩ REF R Analog Input Resistance 100 MΩ AIN Notes: 1. Values are guidelines only. 2. Minimum for AVCC is 2.7V. 3. Maximum for AVCC is 5.5V. 265 2502K–AVR–10/06
ATmega8535 Typical The following charts show typical behavior. These figures are not tested during manu- Characteristics facturing. All current consumption measurements are performed with all I/O pins configured as inputs and with internal pull-ups enabled. A sine wave generator with rail- to-rail output is used as clock source. The power consumption in Power-down mode is independent of clock selection. The current consumption is a function of several factors such as: Operating voltage, operating frequency, loading of I/O pins, switching rate of I/O pins, code executed and ambient temperature. The dominating factors are operating voltage and frequency. The current drawn from capacitive loaded pins may be estimated (for one pin) as C *V *f where C = load capacitance, V = operating voltage and f = average switch- L CC L CC ing frequency of I/O pin. The parts are characterized at frequencies higher than test limits. Parts are not guaran- teed to function properly at frequencies higher than the ordering code indicates. The difference between current consumption in Power-down mode with Watchdog Timer enabled and Power-down mode with Watchdog Timer disabled represents the dif- ferential current drawn by the Watchdog Timer. Active Supply Current Figure 130. Active Supply Current vs. Frequency (0.1 - 1.0 MHz) ACTIVE SUPPLY CURRENT vs. FREQUENCY 0.1 - 1.0 MHz 2 1.8 5.5V 1.6 5.0V 1.4 4.5V 1.2 4.0V A) (mCC 1 33..30VV I 0.8 2.7V 0.6 0.4 0.2 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 Frequency (MHz) ATmega8535(L) 266 2502K–AVR–10/06
ATmega8535(L) Figure 131. Active Supply Current vs. Frequency (1 - 16 MHz) ACTIVE SUPPLY CURRENT vs. FREQUENCY 1 - 16 MHz 25 5.5V 20 5.0V 4.5V 15 4.0V A) m (C C I 10 3.3V 3.0V 5 2.7V 0 0 2 4 6 8 10 12 14 16 Frequency (MHz) Figure 132. Active Supply Current vs. V (Internal RC Oscillator, 8 MHz) CC ACTIVE SUPPLY CURRENT vs. V CC INTERNAL RC OSCILLATOR, 8 MHz 18 16 -40°C 14 25°C 85°C 12 A) 10 m (CC 8 I 6 4 2 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC 267 2502K–AVR–10/06
Figure 133. Active Supply Current vs. V (Internal RC Oscillator, 4 MHz) CC ACTIVE SUPPLY CURRENT vs. V CC INTERNAL RC OSCILLATOR, 4 MHz 10 9 -40°C 8 25°C 7 85°C 6 A) m 5 (C C I 4 3 2 1 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Figure 134. Active Supply Current vs. V (Internal RC Oscillator, 2 MHz) CC ACTIVE SUPPLY CURRENT vs. V CC INTERNAL RC OSCILLATOR, 2 MHz 4.5 4 -40°C 25°C 3.5 85°C 3 A) 2.5 m C ( 2 C I 1.5 1 0.5 0 2.5 3 3.5 4 4.5 5 5.5 VCC (V) ATmega8535(L) 268 2502K–AVR–10/06
ATmega8535(L) Figure 135. Active Supply Current vs. V (Internal RC Oscillator, 1 MHz) CC ACTIVE SUPPLY CURRENT vs. V CC INTERNAL RC OSCILLATOR, 1 MHz 2.5 2 -40°C 25°C 85°C 1.5 A) m (C C I 1 0.5 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Figure 136. Active Supply Current vs. V (32 kHz External Oscillator) CC ACTIVE SUPPLY CURRENT vs. V CC 32kHz EXTERNAL OSCILLATOR 0.08 0.07 25°C 0.06 0.05 A) (mC 0.04 C I 0.03 0.02 0.01 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC 269 2502K–AVR–10/06
Idle Supply Current Figure 137. Idle Supply Current vs. Frequency (0.1 - 1.0 MHz) IDLE SUPPLY CURRENT vs. FREQUENCY 0.1 - 1.0 MHz 0.8 5.5V 0.7 5.0V 0.6 4.5V 0.5 A) 4.0V m 0.4 (C IC 3.3V 0.3 3.0V 0.2 2.7V 0.1 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 Frequency (MHz) Figure 138. Idle Supply Current vs. Frequency (1 - 16 MHz) IDLE SUPPLY CURRENT vs. FREQUENCY 1 - 16 MHz 14 12 5.5V 10 5.0V 4.5V A) 8 m (C IC 6 4.0V 4 3.3V 3.0V 2 2.7V 0 0 2 4 6 8 10 12 14 16 Frequency (MHz) ATmega8535(L) 270 2502K–AVR–10/06
ATmega8535(L) Figure 139. Idle Supply Current vs. V (Internal RC Oscillator, 8 MHz) CC IDLE SUPPLY CURRENT vs. V CC INTERNAL RC OSCILLATOR, 8 MHz 10 9 8 -40°C 25°C 7 85°C 6 A) m 5 (C C I 4 3 2 1 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Figure 140. Idle Supply Current vs. V (Internal RC Oscillator, 4 MHz) CC IDLE SUPPLY CURRENT vs. V CC INTERNAL RC OSCILLATOR, 4 MHz 5 4.5 4 -40°C 25°C 3.5 85°C 3 A) m 2.5 (C C I 2 1.5 1 0.5 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC 271 2502K–AVR–10/06
Figure 141. Idle Supply Current vs. V (Internal RC Oscillator, 2 MHz) CC IDLE SUPPLY CURRENT vs. V CC INTERNAL RC OSCILLATOR, 2 MHz 2.5 2 -40°C 25°C 85°C 1.5 A) m (C C I 1 0.5 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Figure 142. Idle Supply Current vs. V (Internal RC Oscillator, 1 MHz) CC IDLE SUPPLY CURRENT vs. V CC INTERNAL RC OSCILLATOR, 1 MHz 1.2 1 85°C 25°C -40°C 0.8 A) m 0.6 (C C I 0.4 0.2 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC ATmega8535(L) 272 2502K–AVR–10/06
ATmega8535(L) Figure 143. Idle Supply Current vs. V (32 kHz External Oscillator) CC IDLE SUPPLY CURRENT vs. V CC 32kHz EXTERNAL OSCILLATOR 0.04 0.035 25°C 0.03 0.025 A) (mC 0.02 C I 0.015 0.01 0.005 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Power-Down Supply Current Figure 144. Power-Down Supply Current vs. V (Watchdog Timer Disabled) CC POWER-DOWN SUPPLY CURRENT vs. V CC WATCHDOG TIMER DISABLED 2.5 85°C 2 1.5 A) -40°C u (C 25°C C I 1 0.5 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC 273 2502K–AVR–10/06
Figure 145. Power-Down Supply Current vs. V (Watchdog Timer Enabled) CC POWER-DOWN SUPPLY CURRENT vs. V CC WATCHDOG TIMER ENABLED 0.025 0.02 85°C 25°C 0.015 -40°C A) m (C C I 0.01 0.005 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Power-Save Supply Current Figure 146. Power-Save Supply Current vs. V (Watchdog Timer Disabled) CC POWER-SAVE SUPPLY CURRENT vs. V CC WATCHDOG TIMER DISABLED 16 14 12 25°C 10 A) (uC 8 C I 6 4 2 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC ATmega8535(L) 274 2502K–AVR–10/06
ATmega8535(L) Standby Supply Current Figure 147. Standby Supply Current vs. V (455 kHz Resonator, Watchdog Timer CC Disabled) STANDBY SUPPLY CURRENT vs. V CC 455 kHz RESONATOR, WATCHDOG TIMER DISABLED 90 80 70 60 A) 50 u (CC 40 I 30 20 10 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Figure 148. Standby Supply Current vs. V (1 MHz Resonator, Watchdog Timer CC Disabled) STANDBY SUPPLY CURRENT vs. V CC 1 MHz RESONATOR, WATCHDOG TIMER DISABLED 70 60 50 A) 40 u (C IC 30 20 10 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC 275 2502K–AVR–10/06
Figure 149. Standby Supply Current vs. V (2 MHz Resonator, Watchdog Timer CC Disabled) STANDBY SUPPLY CURRENT vs. V CC 2 MHz RESONATOR, WATCHDOG TIMER DISABLED 100 90 80 70 60 A) (uC 50 C I 40 30 20 10 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Figure 150. Standby Supply Current vs. V (2 MHz Xtal, Watchdog Timer Disabled) CC STANDBY SUPPLY CURRENT vs. V CC 2 MHz XTAL, WATCHDOG TIMER DISABLED 100 90 80 70 60 A) (uC 50 C I 40 30 20 10 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC ATmega8535(L) 276 2502K–AVR–10/06
ATmega8535(L) Figure 151. Standby Supply Current vs. V (4 MHz Resonator, Watchdog Timer CC Disabled) STANDBY SUPPLY CURRENT vs. V CC 4 MHz RESONATOR, WATCHDOG TIMER DISABLED 140 120 100 A) 80 u (C IC 60 40 20 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Figure 152. Standby Supply Current vs. V (4 MHz Xtal, Watchdog Timer Disabled) CC STANDBY SUPPLY CURRENT vs. V CC 4 MHz XTAL, WATCHDOG TIMER DISABLED 140 120 100 A) 80 u (C IC 60 40 20 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC 277 2502K–AVR–10/06
Figure 153. Standby Supply Current vs. V (6 MHz Resonator, Watchdog Timer CC Disabled) STANDBY SUPPLY CURRENT vs. V CC 6 MHz RESONATOR, WATCHDOG TIMER DISABLED 180 160 140 120 A) 100 u (CC 80 I 60 40 20 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Figure 154. Standby Supply Current vs. V (6 MHz Xtal, Watchdog Timer Disabled) CC STANDBY SUPPLY CURRENT vs. V CC 6 MHz XTAL, WATCHDOG TIMER DISABLED 180 160 140 120 A) 100 u (CC 80 I 60 40 20 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC ATmega8535(L) 278 2502K–AVR–10/06
ATmega8535(L) Pin Pullup Figure 155. I/O Pin Pull-up Resistor Current vs. Input Voltage (V = 5V) CC I/O PIN PULL-UP RESISTOR CURRENT vs. INPUT VOLTAGE Vcc = 5V 160 140 85°C 25°C 120 -40°C 100 A) (uOP 80 I 60 40 20 0 0 1 2 3 V (V) OP Figure 156. I/O Pin Pull-up Resistor Current vs. Input Voltage (V = 2.7V) CC I/O PIN PULL-UP RESISTOR CURRENT vs. INPUT VOLTAGE Vcc = 2.7V 80 85°C 70 25°C 60 -40°C 50 A) (uOP 40 I 30 20 10 0 0 0.5 1 1.5 2 2.5 3 V (V) OP 279 2502K–AVR–10/06
Figure 157. Reset Pull-up Resistor Current vs. Reset Pin Voltage (V = 5V) CC RESET PULL-UP RESISTOR CURRENT vs. RESET PIN VOLTAGE Vcc = 5V 120 -40°C 25°C 100 85°C 80 A) u (RESET 60 I 40 20 0 0 1 2 3 V (V) RESET Figure 158. Reset Pull-up Resistor Current vs. Reset Pin Voltage (V = 2.7V) CC RESET PULL-UP RESISTOR CURRENT vs. RESET PIN VOLTAGE Vcc = 2.7V 60 -40°C 25°C 50 85°C 40 A) u (RESET 30 I 20 10 0 0 0.5 1 1.5 2 2.5 3 V (V) RESET ATmega8535(L) 280 2502K–AVR–10/06
ATmega8535(L) Pin Driver Strength Figure 159. I/O Pin Source Current vs. Output Voltage (V = 5V) CC I/O PIN SOURCE CURRENT vs. OUTPUT VOLTAGE Vcc = 5V 90 80 -40°C 70 25°C 60 85°C A) 50 m (OH 40 I 30 20 10 0 2.5 3 3.5 4 4.5 5 5.5 V (V) OH Figure 160. I/O Pin Source Current vs. Output Voltage (V = 2.7V) CC I/O PIN SOURCE CURRENT vs. OUTPUT VOLTAGE Vcc = 2.7V 30 -40°C 25 25°C 85°C 20 A) (mH 15 O I 10 5 0 0 0.5 1 1.5 2 2.5 3 V (V) OH 281 2502K–AVR–10/06
Figure 161. I/O Pin Sink Current vs. Output Voltage (V = 5V) CC I/O PIN SINK CURRENT vs. OUTPUT VOLTAGE Vcc = 5V 90 80 -40°C 70 25°C 60 85°C A) 50 m (OL 40 I 30 20 10 0 0 0.5 1 1.5 2 2.5 V (V) OL Figure 162. I/O Pin Sink Current vs. Output Voltage (V = 2.7V) CC I/O PIN SINK CURRENT vs. OUTPUT VOLTAGE Vcc = 2.7V 35 -40°C 30 25°C 25 85°C A) 20 m I (OL 15 10 5 0 0 0.5 1 1.5 2 2.5 V (V) OL ATmega8535(L) 282 2502K–AVR–10/06
ATmega8535(L) Pin Thresholds And Figure 163. I/O Pin Input Threshold Voltage vs. V (V , I/O Pin Read As '1') CC IH Hysteresis I/O PIN INPUT THRESHOLD VOLTAGE vs. V CC VIH, IO PIN READ AS '1' 2.5 -40°C 85°C 2 25°C V) 1.5 d ( ol h s e hr 1 T 0.5 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Figure 164. I/O Pin Input Threshold Voltage vs. V (V , I/O Pin Read As '0') CC IL I/O PIN INPUT THRESHOLD VOLTAGE vs. V CC VIL, IO PIN READ AS '0' 2 -40°C 1.5 25°C 85°C V) d ( hol 1 s e hr T 0.5 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC 283 2502K–AVR–10/06
Figure 165. I/O Pin Input Hysteresis vs. V CC I/O PIN INPUT HYSTERESIS vs. V CC 0.7 85°C 0.6 25°C -40°C 0.5 V) d ( 0.4 ol h s hre 0.3 T 0.2 0.1 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Figure 166. Reset Input Threshold Voltage vs. V (V , Reset Pin Read As '1') CC IH RESET INPUT THRESHOLD VOLTAGE vs. V CC VIH, IO PIN READ AS '1' 2.5 2 -40°C d (V) 1.5 25°C hol 85°C s e Thr 1 0.5 0 2.5 3 3.5 4 4.5 5 5.5 VCC (V) ATmega8535(L) 284 2502K–AVR–10/06
ATmega8535(L) Figure 167. Reset Input Threshold Voltage vs. V (V , Reset Pin Read As '0') CC IL RESET INPUT THRESHOLD VOLTAGE vs. V CC VIL, IO PIN READ AS '0' 3 2.5 85°C -40°C 25°C V) 2 d ( ol h s e Thr 1.5 1 0.5 2.5 3 3.5 4 4.5 5 5.5 VCC (V) Figure 168. Reset Input Pin Hysteresis vs. V CC RESET INPUT PIN HYSTERESIS vs. V CC 0.6 -40°C 0.5 0.4 V) 25°C d ( hol 0.3 s e hr T 85°C 0.2 0.1 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC 285 2502K–AVR–10/06
BOD Thresholds And Analog Figure 169. BOD Thresholds vs. Temperature (BOD Level is 4.0V) Comparator Offset BOD THRESHOLDS vs. TEMPERATURE BOD LEVEL IS 4.0 V 4 Rising V CC 3.95 3.9 V) d ( hol 3.85 s e hr T 3.8 Falling V CC 3.75 3.7 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 Temperature (C) Figure 170. BOD Thresholds vs. Temperature (BOD Level is 2.7V) BOD THRESHOLDS vs. TEMPERATURE BOD LEVEL IS 2.7 V 2.85 2.8 Rising V CC 2.75 V) d ( 2.7 ol h s hre 2.65 T Falling V CC 2.6 2.55 2.5 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 Temperature (C) ATmega8535(L) 286 2502K–AVR–10/06
ATmega8535(L) Figure 171. Bandgap Voltage vs. V CC BANDGAP vs. V CC 1.226 -40°C 1.224 25°C 85°C 1.222 V) 1.22 e ( g a 1.218 olt V ap 1.216 g d n a B 1.214 1.212 1.21 1.208 2.5 3 3.5 4 4.5 5 5.5 Vcc (V) Figure 172. Analog Comparator Offset Voltage vs. Common Mode Voltage (V = 5V) CC ANALOG COMPARATOR OFFSET VOLTAGE vs. COMMON MODE VOLTAGE Vcc = 5V 0.002 0.001 V) 0 e ( g olta -0.001 V et Offs -0.002 25°C or arat -0.003 85°C p m o C -0.004 -0.005 -40°C -0.006 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 Common Mode Voltage (V) 287 2502K–AVR–10/06
Figure 173. Analog Comparator Offset Voltage vs. Common Mode Voltage (V = CC 2.7V) ANALOG COMPARATOR OFFSET VOLTAGE vs. COMMON MODE VOLTAGE Vcc = 2.7V 0.002 0.001 V) ge ( 0 a olt V et Offs -0.001 ator 25°C par -0.002 m o C 85°C -0.003 -40°C -0.004 0 0.5 1 1.5 2 2.5 3 Common Mode Voltage (V) Internal Oscillator Speed Figure 174. Watchdog Oscillator Frequency vs. V CC WATCHDOG OSCILLATOR FREQUENCY vs. V CC 1300 1250 -40°C 25°C 85°C 1200 z) H (kC 1150 R F 1100 1050 1000 2.5 3 3.5 4 4.5 5 5.5 V (V) CC ATmega8535(L) 288 2502K–AVR–10/06
ATmega8535(L) Figure 175. Calibrated 8 MHz RC Oscillator Frequency vs. Temperature CALIBRATED 8 MHz RC OSCILLATOR FREQUENCY vs. TEMPERATURE 9 8.5 8 z) 5.5V H M 7.5 (RC 4.0V F 7 2.7V 6.5 6 -50 -30 -10 10 30 50 70 90 110 Temp (C˚) Figure 176. Calibrated 8 MHz RC Oscillator Frequency vs. V CC CALIBRATED 8 MHz RC OSCILLATOR FREQUENCY vs. V CC 8.5 -40°C 8.3 8.1 25°C 7.9 85°C 7.7 z) H M 7.5 (C R F 7.3 7.1 6.9 6.7 6.5 2.5 3 3.5 4 4.5 5 5.5 V (V) CC 289 2502K–AVR–10/06
Figure 177. Calibrated 8 MHz RC Oscillator Frequency vs. Osccal Value CALIBRATED 8 MHz RC OSCILLATOR FREQUENCY vs.OSCCAL VALUE 18 16 14 12 Hz) 10 M (RC 8 F 6 4 2 0 0 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 OSCCAL VALUE Figure 178. Calibrated 4 MHz RC Oscillator Frequency vs. Temperature CALIBRATED 4 MHz RC OSCILLATOR FREQUENCY vs. TEMPERATURE 4.2 4.1 4 5.5V z) 3.9 H M (C FR 3.8 4.0V 3.7 2.7V 3.6 3.5 -50 -30 -10 10 30 50 70 90 110 Temp (C˚) ATmega8535(L) 290 2502K–AVR–10/06
ATmega8535(L) Figure 179. Calibrated 4 MHz RC Oscillator Frequency vs. V CC CALIBRATED 4 MHz RC OSCILLATOR FREQUENCY vs. V CC 4.2 4.1 -40°C 25°C 4 85°C 3.9 z) H M 3.8 (C R F 3.7 3.6 3.5 3.4 2 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Figure 180. Calibrated 4 MHz RC Oscillator Frequency vs. Osccal Value CALIBRATED 4 MHz RC OSCILLATOR FREQUENCY vs. OSCCAL VALUE 9 8 7 6 Hz) 5 M (RC 4 F 3 2 1 0 0 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 OSCCAL VALUE 291 2502K–AVR–10/06
Figure 181. Calibrated 2 MHz RC Oscillator Frequency vs. Temperature CALIBRATED 2 MHz RC OSCILLATOR FREQUENCY vs. TEMPERATURE 2.1 2.05 2 5.5V z) 1.95 H M (C FR 1.9 4.0V 1.85 2.7V 1.8 1.75 -50 -30 -10 10 30 50 70 90 110 Temp (C˚) Figure 182. Calibrated 2 MHz RC Oscillator Frequency vs. V CC CALIBRATED 2 MHz RC OSCILLATOR FREQUENCY vs. V CC 2.15 2.1 -40°C 2.05 25°C 2 Hz) 1.95 85°C M (RC 1.9 F 1.85 1.8 1.75 1.7 2.5 3 3.5 4 4.5 5 5.5 V (V) CC ATmega8535(L) 292 2502K–AVR–10/06
ATmega8535(L) Figure 183. Calibrated 2 MHz RC Oscillator Frequency vs. Osccal Value CALIBRATED 2 MHz RC OSCILLATOR FREQUENCY vs. OSCCAL VALUE 4 3.5 3 2.5 z) H M 2 (C R F 1.5 1 0.5 0 0 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 OSCCAL VALUE Figure 184. Calibrated 1 MHz RC Oscillator Frequency vs. Temperature CALIBRATED 1 MHz RC OSCILLATOR FREQUENCY vs. TEMPERATURE 1.04 1.02 1 5.5V z) 0.98 H M (C FR 0.96 4.0V 0.94 0.92 2.7V 0.9 -50 -30 -10 10 30 50 70 90 110 Temp (C˚) 293 2502K–AVR–10/06
Figure 185. Calibrated 1 MHz RC Oscillator Frequency vs. V CC CALIBRATED 1 MHz RC OSCILLATOR FREQUENCY vs. V CC 1.05 1.03 -40°C 1.01 25°C 0.99 85°C 0.97 z) H M 0.95 (C R F 0.93 0.91 0.89 0.87 0.85 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Figure 186. Calibrated 1 MHz RC Oscillator Frequency vs. Osccal Value CALIBRATED 1 MHz RC OSCILLATOR FREQUENCY vs. OSCCAL VALUE 2 1.8 1.6 1.4 1.2 z) H M 1 (C R F 0.8 0.6 0.4 0.2 0 0 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 OSCCAL VALUE ATmega8535(L) 294 2502K–AVR–10/06
ATmega8535(L) Current Consumption Of Figure 187. Brownout Detector Current vs. V CC Peripheral Units BROWNOUT DETECTOR CURRENT vs. V CC 0.025 0.02 -40°C 25°C 85°C 0.015 A) m (C C I 0.01 0.005 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Figure 188. ADC Current vs. V (AREF = AVCC) CC ADC CURRENT vs. V CC AREF = AVCC 600 500 -40°C 400 25°C 85°C A) (uC 300 C I 200 100 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC 295 2502K–AVR–10/06
Figure 189. AREF External Reference Current vs. V CC AREF EXTERNAL REFERENCE CURRENT vs. V CC 250 25°C 200 85°C -40°C 150 A) u (C C I 100 50 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Figure 190. Analog Comparator Current vs. V CC ANALOG COMPARATOR CURRENT vs. V CC 120 100 85°C 25°C 80 -40°C A) (uC 60 C I 40 20 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC ATmega8535(L) 296 2502K–AVR–10/06
ATmega8535(L) Figure 191. Programming Current vs. V CC PROGRAMMING CURRENT vs. V CC 12 10 -40°C 8 25°C A) (mC 6 85°C C I 4 2 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC Current Consumption In Figure 192. Reset Supply Current vs. V (0.1 - 1.0 MHz, Excluding Current Through CC Reset And Reset Pulsewidth The Reset Pull-up) RESET SUPPLY CURRENT vs. V CC 0.1 - 1.0 MHz, EXCLUDING CURRENT THROUGH THE RESET PULLUP 3 5.5V 2.5 5.0V 2 4.5V A) 4.0V (mC 1.5 C I 3.3V 1 3.0V 2.7V 0.5 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 Frequency (MHz) 297 2502K–AVR–10/06
Figure 193. Reset Supply Current vs. V (1 - 20 MHz, Excluding Current Through The CC Reset Pull-up) RESET SUPPLY CURRENT vs. V CC 1 - 20 MHz, EXCLUDING CURRENT THROUGH THE RESET PULLUP 25 5.5V 20 5.0V 4.5V 15 A) m (C C 4.0V I 10 3.3V 5 3.0V 2.7V 0 0 2 4 6 8 10 12 14 16 18 20 Frequency (MHz) Figure 194. Reset Pulse Width vs. V CC RESET PULSE WIDTH vs. V CC 1200 1000 800 s) n h ( widt 600 e s 85°C ul P 400 25°C -40°C 200 0 2.5 3 3.5 4 4.5 5 5.5 V (V) CC ATmega8535(L) 298 2502K–AVR–10/06
ATmega8535(L) Register Summary . Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page 0x3F (0x5F) SREG I T H S V N Z C 10 0x3E (0x5E) SPH – – – – – – SP9 SP8 12 0x3D (0x5D) SPL SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 12 0x3C (0x5C) OCR0 Timer/Counter0 Output Compare Register 85 0x3B (0x5B) GICR INT1 INT0 INT2 – – – IVSEL IVCE 49, 69 0x3A (0x5A) GIFR INTF1 INTF0 INTF2 – – – – – 70 0x39 (0x59) TIMSK OCIE2 TOIE2 TICIE1 OCIE1A OCIE1B TOIE1 OCIE0 TOIE0 85, 115, 133 0x38 (0x58) TIFR OCF2 TOV2 ICF1 OCF1A OCF1B TOV1 OCF0 TOV0 86, 116, 134 0x37 (0x57) SPMCR SPMIE RWWSB – RWWSRE BLBSET PGWRT PGERS SPMEN 228 0x36 (0x56) TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE 181 0x35 (0x55) MCUCR SM2 SE SM1 SM0 ISC11 ISC10 ISC01 ISC00 32, 68 0x34 (0x54) MCUCSR – ISC2 – – WDRF BORF EXTRF PORF 40, 69 0x33 (0x53) TCCR0 FOC0 WGM00 COM01 COM00 WGM01 CS02 CS01 CS00 83 0x32 (0x52) TCNT0 Timer/Counter0 (8 Bits) 85 0x31 (0x51) OSCCAL Oscillator Calibration Register 30 0x30 (0x50) SFIOR ADTS2 ADTS1 ADTS0 – ACME PUD PSR2 PSR10 59,88,135,203,223 0x2F (0x4F) TCCR1A COM1A1 COM1A0 COM1B1 COM1B0 FOC1A FOC1B WGM11 WGM10 110 0x2E (0x4E) TCCR1B ICNC1 ICES1 – WGM13 WGM12 CS12 CS11 CS10 113 0x2D (0x4D) TCNT1H Timer/Counter1 – Counter Register High Byte 114 0x2C (0x4C) TCNT1L Timer/Counter1 – Counter Register Low Byte 114 0x2B (0x4B) OCR1AH Timer/Counter1 – Output Compare Register A High Byte 114 0x2A (0x4A) OCR1AL Timer/Counter1 – Output Compare Register A Low Byte 114 0x29 (0x49) OCR1BH Timer/Counter1 – Output Compare Register B High Byte 114 0x28 (0x48) OCR1BL Timer/Counter1 – Output Compare Register B Low Byte 114 0x27 (0x47) ICR1H Timer/Counter1 – Input Capture Register High Byte 114 0x26 (0x46) ICR1L Timer/Counter1 – Input Capture Register Low Byte 114 0x25 (0x45) TCCR2 FOC2 WGM20 COM21 COM20 WGM21 CS22 CS21 CS20 128 0x24 (0x44) TCNT2 Timer/Counter2 (8 Bits) 130 0x23 (0x43) OCR2 Timer/Counter2 Output Compare Register 131 0x22 (0x42) ASSR – – – – AS2 TCN2UB OCR2UB TCR2UB 131 0x21 (0x41) WDTCR – – – WDCE WDE WDP2 WDP1 WDP0 42 UBRRH URSEL – – – UBRR[11:8] 169 0x20(1) (0x40)(1) UCSRC URSEL UMSEL UPM1 UPM0 USBS UCSZ1 UCSZ0 UCPOL 167 0x1F (0x3F) EEARH – – – – – – – EEAR8 19 0x1E (0x3E) EEARL EEPROM Address Register Low Byte 19 0x1D (0x3D) EEDR EEPROM Data Register 19 0x1C (0x3C) EECR – – – – EERIE EEMWE EEWE EERE 19 0x1B (0x3B) PORTA PORTA7 PORTA6 PORTA5 PORTA4 PORTA3 PORTA2 PORTA1 PORTA0 66 0x1A (0x3A) DDRA DDA7 DDA6 DDA5 DDA4 DDA3 DDA2 DDA1 DDA0 66 0x19 (0x39) PINA PINA7 PINA6 PINA5 PINA4 PINA3 PINA2 PINA1 PINA0 66 0x18 (0x38) PORTB PORTB7 PORTB6 PORTB5 PORTB4 PORTB3 PORTB2 PORTB1 PORTB0 66 0x17 (0x37) DDRB DDB7 DDB6 DDB5 DDB4 DDB3 DDB2 DDB1 DDB0 66 0x16 (0x36) PINB PINB7 PINB6 PINB5 PINB4 PINB3 PINB2 PINB1 PINB0 67 0x15 (0x35) PORTC PORTC7 PORTC6 PORTC5 PORTC4 PORTC3 PORTC2 PORTC1 PORTC0 67 0x14 (0x34) DDRC DDC7 DDC6 DDC5 DDC4 DDC3 DDC2 DDC1 DDC0 67 0x13 (0x33) PINC PINC7 PINC6 PINC5 PINC4 PINC3 PINC2 PINC1 PINC0 67 0x12 (0x32) PORTD PORTD7 PORTD6 PORTD5 PORTD4 PORTD3 PORTD2 PORTD1 PORTD0 67 0x11 (0x31) DDRD DDD7 DDD6 DDD5 DDD4 DDD3 DDD2 DDD1 DDD0 67 0x10 (0x30) PIND PIND7 PIND6 PIND5 PIND4 PIND3 PIND2 PIND1 PIND0 67 0x0F (0x2F) SPDR SPI Data Register 143 0x0E (0x2E) SPSR SPIF WCOL – – – – – SPI2X 143 0x0D (0x2D) SPCR SPIE SPE DORD MSTR CPOL CPHA SPR1 SPR0 141 0x0C (0x2C) UDR USART I/O Data Register 164 0x0B (0x2B) UCSRA RXC TXC UDRE FE DOR PE U2X MPCM 165 0x0A (0x2A) UCSRB RXCIE TXCIE UDRIE RXEN TXEN UCSZ2 RXB8 TXB8 166 0x09 (0x29) UBRRL USART Baud Rate Register Low Byte 169 0x08 (0x28) ACSR ACD ACBG ACO ACI ACIE ACIC ACIS1 ACIS0 203 0x07 (0x27) ADMUX REFS1 REFS0 ADLAR MUX4 MUX3 MUX2 MUX1 MUX0 219 0x06 (0x26) ADCSRA ADEN ADSC ADATE ADIF ADIE ADPS2 ADPS1 ADPS0 221 0x05 (0x25) ADCH ADC Data Register High Byte 222 0x04 (0x24) ADCL ADC Data Register Low Byte 222 0x03 (0x23) TWDR Two-wire Serial Interface Data Register 183 0x02 (0x22) TWAR TWA6 TWA5 TWA4 TWA3 TWA2 TWA1 TWA0 TWGCE 183 0x01 (0x21) TWSR TWS7 TWS6 TWS5 TWS4 TWS3 – TWPS1 TWPS0 183 299 2502K–AVR–10/06
Register Summary (Continued) Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page 0x00 (0x20) TWBR Two-wire Serial Interface Bit Rate Register 181 Notes: 1. Refer to the USART description for details on how to access UBRRH and UCSRC. 2. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses should never be written. 3. Some of the status flags are cleared by writing a logical one to them. Note that the CBI and SBI instructions will operate on all bits in the I/O Register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI instructions work with registers 0x00 to 0x1F only. ATmega8535(L) 300 2502K–AVR–10/06
ATmega8535(L) Instruction Set Summary Mnemonics Operands Description Operation Flags #Clocks ARITHMETIC AND LOGIC INSTRUCTIONS ADD Rd, Rr Add two Registers Rd ← Rd + Rr Z,C,N,V,H 1 ADC Rd, Rr Add with Carry two Registers Rd ← Rd + Rr + C Z,C,N,V,H 1 ADIW Rdl,K Add Immediate to Word Rdh:Rdl ← Rdh:Rdl + K Z,C,N,V,S 2 SUB Rd, Rr Subtract two Registers Rd ← Rd - Rr Z,C,N,V,H 1 SUBI Rd, K Subtract Constant from Register Rd ← Rd - K Z,C,N,V,H 1 SBC Rd, Rr Subtract with Carry two Registers Rd ← Rd - Rr - C Z,C,N,V,H 1 SBCI Rd, K Subtract with Carry Constant from Reg. Rd ← Rd - K - C Z,C,N,V,H 1 SBIW Rdl,K Subtract Immediate from Word Rdh:Rdl ← Rdh:Rdl - K Z,C,N,V,S 2 AND Rd, Rr Logical AND Registers Rd ← Rd • Rr Z,N,V 1 ANDI Rd, K Logical AND Register and Constant Rd ← Rd • K Z,N,V 1 OR Rd, Rr Logical OR Registers Rd ← Rd v Rr Z,N,V 1 ORI Rd, K Logical OR Register and Constant Rd ← Rd v K Z,N,V 1 EOR Rd, Rr Exclusive OR Registers Rd ← Rd ⊕ Rr Z,N,V 1 COM Rd One’s Complement Rd ← 0xFF − Rd Z,C,N,V 1 NEG Rd Two’s Complement Rd ← 0x00 − Rd Z,C,N,V,H 1 SBR Rd,K Set Bit(s) in Register Rd ← Rd v K Z,N,V 1 CBR Rd,K Clear Bit(s) in Register Rd ← Rd • (0xFF - K) Z,N,V 1 INC Rd Increment Rd ← Rd + 1 Z,N,V 1 DEC Rd Decrement Rd ← Rd − 1 Z,N,V 1 TST Rd Test for Zero or Minus Rd ← Rd • Rd Z,N,V 1 CLR Rd Clear Register Rd ← Rd ⊕ Rd Z,N,V 1 SER Rd Set Register Rd ← 0xFF None 1 MUL Rd, Rr Multiply Unsigned R1:R0 ← Rd x Rr Z,C 2 MULS Rd, Rr Multiply Signed R1:R0 ← Rd x Rr Z,C 2 MULSU Rd, Rr Multiply Signed with Unsigned R1:R0 ← Rd x Rr Z,C 2 FMUL Rd, Rr Fractional Multiply Unsigned R1:R0 ← (Rd x Rr) << 1 Z,C 2 FMULS Rd, Rr Fractional Multiply Signed R1:R0 ← (Rd x Rr) << 1 Z,C 2 FMULSU Rd, Rr Fractional Multiply Signed with Unsigned R1:R0 ← (Rd x Rr) << 1 Z,C 2 BRANCH INSTRUCTIONS RJMP k Relative Jump PC ← PC + k + 1 None 2 IJMP Indirect Jump to (Z) PC ← Z None 2 RCALL k Relative Subroutine Call PC ← PC + k + 1 None 3 ICALL Indirect Call to (Z) PC ← Z None 3 RET Subroutine Return PC ← STACK None 4 RETI Interrupt Return PC ← STACK I 4 CPSE Rd,Rr Compare, Skip if Equal if (Rd = Rr) PC ← PC + 2 or 3 None 1 / 2 / 3 CP Rd,Rr Compare Rd − Rr Z, N,V,C,H 1 CPC Rd,Rr Compare with Carry Rd − Rr − C Z, N,V,C,H 1 CPI Rd,K Compare Register with Immediate Rd − K Z, N,V,C,H 1 SBRC Rr, b Skip if Bit in Register Cleared if (Rr(b)=0) PC ← PC + 2 or 3 None 1 / 2 / 3 SBRS Rr, b Skip if Bit in Register is Set if (Rr(b)=1) PC ← PC + 2 or 3 None 1 / 2 / 3 SBIC P, b Skip if Bit in I/O Register Cleared if (P(b)=0) PC ← PC + 2 or 3 None 1 / 2 / 3 SBIS P, b Skip if Bit in I/O Register is Set if (P(b)=1) PC ← PC + 2 or 3 None 1 / 2 / 3 BRBS s, k Branch if Status Flag Set if (SREG(s) = 1) then PC←PC+k + 1 None 1 / 2 BRBC s, k Branch if Status Flag Cleared if (SREG(s) = 0) then PC←PC+k + 1 None 1 / 2 BREQ k Branch if Equal if (Z = 1) then PC ← PC + k + 1 None 1 / 2 BRNE k Branch if Not Equal if (Z = 0) then PC ← PC + k + 1 None 1 / 2 BRCS k Branch if Carry Set if (C = 1) then PC ← PC + k + 1 None 1 / 2 BRCC k Branch if Carry Cleared if (C = 0) then PC ← PC + k + 1 None 1 / 2 BRSH k Branch if Same or Higher if (C = 0) then PC ← PC + k + 1 None 1 / 2 BRLO k Branch if Lower if (C = 1) then PC ← PC + k + 1 None 1 / 2 BRMI k Branch if Minus if (N = 1) then PC ← PC + k + 1 None 1 / 2 BRPL k Branch if Plus if (N = 0) then PC ← PC + k + 1 None 1 / 2 BRGE k Branch if Greater or Equal, Signed if (N ⊕ V= 0) then PC ← PC + k + 1 None 1 / 2 BRLT k Branch if Less Than Zero, Signed if (N ⊕ V= 1) then PC ← PC + k + 1 None 1 / 2 BRHS k Branch if Half Carry Flag Set if (H = 1) then PC ← PC + k + 1 None 1 / 2 BRHC k Branch if Half Carry Flag Cleared if (H = 0) then PC ← PC + k + 1 None 1 / 2 BRTS k Branch if T Flag Set if (T = 1) then PC ← PC + k + 1 None 1 / 2 BRTC k Branch if T Flag Cleared if (T = 0) then PC ← PC + k + 1 None 1 / 2 BRVS k Branch if Overflow Flag is Set if (V = 1) then PC ← PC + k + 1 None 1 / 2 BRVC k Branch if Overflow Flag is Cleared if (V = 0) then PC ← PC + k + 1 None 1 / 2 BRIE k Branch if Interrupt Enabled if ( I = 1) then PC ← PC + k + 1 None 1 / 2 BRID k Branch if Interrupt Disabled if ( I = 0) then PC ← PC + k + 1 None 1 / 2 DATA TRANSFER INSTRUCTIONS 301 2502K–AVR–10/06
Mnemonics Operands Description Operation Flags #Clocks MOV Rd, Rr Move Between Registers Rd ← Rr None 1 MOVW Rd, Rr Copy Register Word Rd+1:Rd ← Rr+1:Rr None 1 LDI Rd, K Load Immediate Rd ← K None 1 LD Rd, X Load Indirect Rd ← (X) None 2 LD Rd, X+ Load Indirect and Post-Inc. Rd ← (X), X ← X + 1 None 2 LD Rd, - X Load Indirect and Pre-Dec. X ← X - 1, Rd ← (X) None 2 LD Rd, Y Load Indirect Rd ← (Y) None 2 LD Rd, Y+ Load Indirect and Post-Inc. Rd ← (Y), Y ← Y + 1 None 2 LD Rd, - Y Load Indirect and Pre-Dec. Y ← Y - 1, Rd ← (Y) None 2 LDD Rd,Y+q Load Indirect with Displacement Rd ← (Y + q) None 2 LD Rd, Z Load Indirect Rd ← (Z) None 2 LD Rd, Z+ Load Indirect and Post-Inc. Rd ← (Z), Z ← Z+1 None 2 LD Rd, -Z Load Indirect and Pre-Dec. Z ← Z - 1, Rd ← (Z) None 2 LDD Rd, Z+q Load Indirect with Displacement Rd ← (Z + q) None 2 LDS Rd, k Load Direct from SRAM Rd ← (k) None 2 ST X, Rr Store Indirect (X) ← Rr None 2 ST X+, Rr Store Indirect and Post-Inc. (X) ← Rr, X ← X + 1 None 2 ST - X, Rr Store Indirect and Pre-Dec. X ← X - 1, (X) ← Rr None 2 ST Y, Rr Store Indirect (Y) ← Rr None 2 ST Y+, Rr Store Indirect and Post-Inc. (Y) ← Rr, Y ← Y + 1 None 2 ST - Y, Rr Store Indirect and Pre-Dec. Y ← Y - 1, (Y) ← Rr None 2 STD Y+q,Rr Store Indirect with Displacement (Y + q) ← Rr None 2 ST Z, Rr Store Indirect (Z) ← Rr None 2 ST Z+, Rr Store Indirect and Post-Inc. (Z) ← Rr, Z ← Z + 1 None 2 ST -Z, Rr Store Indirect and Pre-Dec. Z ← Z - 1, (Z) ← Rr None 2 STD Z+q,Rr Store Indirect with Displacement (Z + q) ← Rr None 2 STS k, Rr Store Direct to SRAM (k) ← Rr None 2 LPM Load Program Memory R0 ← (Z) None 3 LPM Rd, Z Load Program Memory Rd ← (Z) None 3 LPM Rd, Z+ Load Program Memory and Post-Inc Rd ← (Z), Z ← Z+1 None 3 SPM Store Program Memory (Z) ← R1:R0 None - IN Rd, P In Port Rd ← P None 1 OUT P, Rr Out Port P ← Rr None 1 PUSH Rr Push Register on Stack STACK ← Rr None 2 POP Rd Pop Register from Stack Rd ← STACK None 2 BIT AND BIT-TEST INSTRUCTIONS SBI P,b Set Bit in I/O Register I/O(P,b) ← 1 None 2 CBI P,b Clear Bit in I/O Register I/O(P,b) ← 0 None 2 LSL Rd Logical Shift Left Rd(n+1) ← Rd(n), Rd(0) ← 0 Z,C,N,V 1 LSR Rd Logical Shift Right Rd(n) ← Rd(n+1), Rd(7) ← 0 Z,C,N,V 1 ROL Rd Rotate Left Through Carry Rd(0)←C,Rd(n+1)← Rd(n),C←Rd(7) Z,C,N,V 1 ROR Rd Rotate Right Through Carry Rd(7)←C,Rd(n)← Rd(n+1),C←Rd(0) Z,C,N,V 1 ASR Rd Arithmetic Shift Right Rd(n) ← Rd(n+1), n=0..6 Z,C,N,V 1 SWAP Rd Swap Nibbles Rd(3..0)←Rd(7..4),Rd(7..4)←Rd(3..0) None 1 BSET s Flag Set SREG(s) ← 1 SREG(s) 1 BCLR s Flag Clear SREG(s) ← 0 SREG(s) 1 BST Rr, b Bit Store from Register to T T ← Rr(b) T 1 BLD Rd, b Bit load from T to Register Rd(b) ← T None 1 SEC Set Carry C ← 1 C 1 CLC Clear Carry C ← 0 C 1 SEN Set Negative Flag N ← 1 N 1 CLN Clear Negative Flag N ← 0 N 1 SEZ Set Zero Flag Z ← 1 Z 1 CLZ Clear Zero Flag Z ← 0 Z 1 SEI Global Interrupt Enable I ← 1 I 1 CLI Global Interrupt Disable I ← 0 I 1 SES Set Signed Test Flag S ← 1 S 1 CLS Clear Signed Test Flag S ← 0 S 1 SEV Set Twos Complement Overflow. V ← 1 V 1 CLV Clear Twos Complement Overflow V ← 0 V 1 SET Set T in SREG T ← 1 T 1 CLT Clear T in SREG T ← 0 T 1 SEH Set Half Carry Flag in SREG H ← 1 H 1 CLH Clear Half Carry Flag in SREG H ← 0 H 1 MCU CONTROL INSTRUCTIONS NOP No Operation None 1 ATmega8535(L) 302 2502K–AVR–10/06
ATmega8535(L) Mnemonics Operands Description Operation Flags #Clocks SLEEP Sleep (see specific descr. for Sleep function) None 1 WDR Watchdog Reset (see specific descr. for WDR/Timer) None 1 BREAK Break For On-chip Debug Only None N/A 303 2502K–AVR–10/06
Ordering Information Speed (MHz) Power Supply Ordering Code Package(1) Operation Range ATmega8535L-8AC 44A ATmega8535L-8PC 40P6 Commercial ATmega8535L-8JC 44J (0°C to 70°C) ATmega8535L-8MC 44M1 ATmega8535L-8AI 44A ATmega8535L-8PI 40P6 8 2.7 - 5.5V ATmega8535L-8JI 44J ATmega8535L-8MI 44M1 Industrial ATmega8535L-8AU(2) 44A (-40°C to 85°C) ATmega8535L-8PU(2) 40P6 ATmega8535L-8JU(2) 44J ATmega8535L-8MU(2) 44M1 ATmega8535-16AC 44A ATmega8535-16PC 40P6 Commercial ATmega8535-16JC 44J (0°C to 70°C) ATmega8535-16MC 44M1 ATmega8535-16AI 44A ATmega8535-16PI 40P6 16 4.5 - 5.5V ATmega8535-16JI 44J ATmega8535-16MI 44M1 Industrial ATmega8535-16AU(2) 44A (-40°C to 85°C) ATmega8535-16PU(2) 40P6 ATmega8535-16JU(2) 44J ATmega8535-16MU(2) 44M1 Note: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities.. 2. Pb-free packaging alternative, complies to the European Directive for Restriction of Hazardous Substances (RoHS direc- tive).Also Halide free and fully Green. ATmega8535(L) 304 2502K–AVR–10/06
ATmega8535(L) Package Type 44A 44-lead, Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) 40P6 40-pin, 0.600” Wide, Plastic Dual Inline Package (PDIP) 44J 44-lead, Plastic J-leaded Chip Carrier (PLCC) 44M1-A 44-pad, 7 x 7 x 1.0 mm body, lead pitch 0.50 mm, Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 305 2502K–AVR–10/06
Packaging Information 44A PIN 1 B PIN 1 IDENTIFIER e E1 E D1 D C 0˚~7˚ A1 A2 A L COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A – – 1.20 A1 0.05 – 0.15 A2 0.95 1.00 1.05 D 11.75 12.00 12.25 D1 9.90 10.00 10.10 Note 2 E 11.75 12.00 12.25 Notes: 1.This package conforms to JEDEC reference MS-026, Variation ACB. E1 9.90 10.00 10.10 Note 2 2.Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum B 0.30 – 0.45 plastic body size dimensions including mold mismatch. C 0.09 – 0.20 3. Lead coplanarity is 0.10 mm maximum. L 0.45 – 0.75 e 0.80 TYP 10/5/2001 TITLE DRAWING NO. REV. 2325 Orchard Parkway 44A, 44-lead, 10 x 10 mm Body Size, 1.0 mm Body Thickness, San Jose, CA 95131 44A B R 0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) ATmega8535(L) 306 2502K–AVR–10/06
ATmega8535(L) 40P6 D PIN 1 E1 A SEATING PLANE A1 L B B1 e E COMMON DIMENSIONS 0º ~ 15º REF (Unit of Measure = mm) C SYMBOL MIN NOM MAX NOTE eB A – – 4.826 A1 0.381 – – D 52.070 – 52.578 Note 2 E 15.240 – 15.875 E1 13.462 – 13.970 Note 2 B 0.356 – 0.559 B1 1.041 – 1.651 Notes: 1.This package conforms to JEDEC reference MS-011, Variation AC. 2.Dimensions D and E1 do not include mold Flash or Protrusion. L 3.048 – 3.556 Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). C 0.203 – 0.381 eB 15.494 – 17.526 e 2.540 TYP 09/28/01 TITLE DRAWING NO. REV. 2325 Orchard Parkway 40P6, 40-lead (0.600"/15.24 mm Wide) Plastic Dual R San Jose, CA 95131 Inline Package (PDIP) 40P6 B 307 2502K–AVR–10/06
44J 1.14(0.045) X 45˚ 1.14(0.045) X 45˚ PIN NO. 1 0.318(0.0125) IDENTIFIER 0.191(0.0075) E1 E B1 D2/E2 B e A2 D1 A1 D A 0.51(0.020)MAX 45˚ MAX (3X) COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A 4.191 – 4.572 A1 2.286 – 3.048 A2 0.508 – – D 17.399 – 17.653 D1 16.510 – 16.662 Note 2 E 17.399 – 17.653 Notes: 1.This package conforms to JEDEC reference MS-018, Variation AC. E1 16.510 – 16.662 Note 2 2.Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 D2/E2 14.986 – 16.002 and E1 include mold mismatch and are measured at the extreme B 0.660 – 0.813 material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. B1 0.330 – 0.533 e 1.270 TYP 10/04/01 TITLE DRAWING NO. REV. 2325 Orchard Parkway 44J, 44-lead, Plastic J-leaded Chip Carrier (PLCC) San Jose, CA 95131 44J B R ATmega8535(L) 308 2502K–AVR–10/06
ATmega8535(L) 44M1-A D Marked Pin# 1 ID E SEATING PLANE A1 TOP VIEW A3 A K L D2 Pin #1 Corner SIDE VIEW 1 Option A Pin #1 Triangle 2 3 COMMON DIMENSIONS (Unit of Measure = mm) E2 SYMBOL MIN NOM MAX NOTE Option B Pin #1 A 0.80 0.90 1.00 Chamfer (C 0.30) A1 – 0.02 0.05 A3 0.25 REF b 0.18 0.23 0.30 D 6.9 0 7.00 7.10 K Option C Pin #1 b e Notch D2 5.00 5.20 5.40 (0.20 R) E 6.90 7.00 7.10 BOTTOM VIEW E2 5.00 5.20 5.40 e 0.50 BSC L 0.59 0.64 0.69 Note: JEDEC Standard MO-220, Fig. 1 (SAW Singulation) VKKD-3. K 0.20 0.26 0.41 5/27/06 TITLE DRAWING NO. REV. 2325 Orchard Parkway 44M1, 44-pad, 7 x 7 x 1.0 mm Body, Lead Pitch 0.50 mm, R San Jose, CA 95131 5.20 mm Exposed Pad, Micro Lead Frame Package (MLF) 44M1 G 309 2502K–AVR–10/06
Errata The revision letter refer to the device revision. ATmega8535 (cid:129) First Analog Comparator conversion may be delayed Rev. A and B (cid:129) Asynchronous Oscillator does not stop in Power-down 1. First Analog Comparator conversion may be delayed If the device is powered by a slow rising V , the first Analog Comparator conver- CC sion will take longer than expected on some devices. Problem Fix/Workaround When the device has been powered or reset, disable then enable the Analog Com- parator before the first conversion. 2. Asynchronous Oscillator does not stop in Power-down The asynchronous oscillator does not stop when entering Power-down mode. This leads to higher power consumption than expected. Problem Fix/Workaround Manually disable the asynchronous timer before entering Power-down. ATmega8535(L) 310 2502K–AVR–10/06
ATmega8535(L) Datasheet Revision Please note that the referring page numbers in this section are referring to this docu- History ment. The referring revision in this section are referring to the document revision. Changes from Rev. 1. Updated TOP/BOTTOM description for all Timer/Counters Fast PWM mode. 2502J- 08/06 to Rev. 2502K- 10/06 2. Updated “Errata” on page 310. Changes from Rev. 1. Updated “Ordering Information” on page 304. 2502I- 06/06 to Rev. 2502J- 08/06 Changes from Rev. 1. Updated code example “USART Initialization” on page 150. 2502H- 04/06 to Rev. 2502I- 06/06 Changes from Rev. 1. Added “Resources” on page 6. 2502G- 04/05 to Rev. 2502H- 04/06 2. Updated Table 7 on page 29, Table 17 on page 42 and Table 111 on page 258. 3. Updated “Serial Peripheral Interface – SPI” on page 136. 4. Updated note in “Bit Rate Generator Unit” on page 180. Changes from Rev. 1. Removed “Preliminary” and TBD’s. 2502F- 06/04 to Rev. 2502G- 04/05 2. Updated Table 37 on page 69 and Table 113 on page 261. 3. Updated “Electrical Characteristics” on page 255. 4. Updated “Ordering Information” on page 304. Changes from Rev. 1. MLF-package alternative changed to “Quad Flat No-Lead/Micro Lead Frame 2502E-12/03 to Rev. Package QFN/MLF”. 2502G-06/04 Changes from Rev. 1. Updated “Reset Characteristics” on page 37. 2502E-12/03 to Rev. 2502F-06/04 2. Updated SPH in “Stack Pointer” on page 12. 3. Updated C code in “USART Initialization” on page 150. 4. Updated “Errata” on page 310. Changes from Rev. 1. Updated “Calibrated Internal RC Oscillator” on page 29. 2502D-09/03 to Rev. 2502E-12/03 2. Added section “Errata” on page 310. 311 2502K–AVR–10/06
Changes from Rev. 1. Removed “Advance Information” and some TBD’s from the datasheet. 2502C-04/03 to Rev. 2502D-09/03 2. Added note to “Pinout ATmega8535” on page 2. 3. Updated “Reset Characteristics” on page 37. 4. Updated “Absolute Maximum Ratings” and “DC Characteristics” in “Electrical Characteristics” on page 255. 5. Updated Table 111 on page 258. 6. Updated “ADC Characteristics” on page 263. 7. Updated “ATmega8535 Typical Characteristics” on page 266. 8. Removed CALL and JMP instructions from code examples and “Instruction Set Summary” on page 301. Changes from Rev. 1. Updated “Packaging Information” on page 306. 2502B-09/02 to Rev. 2502C-04/03 2. Updated Figure 1 on page 2, Figure 84 on page 179, Figure 85 on page 185, Figure 87 on page 191, Figure 98 on page 207. 3. Added the section “EEPROM Write During Power-down Sleep Mode” on page 22. 4. Removed the references to the application notes “Multi-purpose Oscillator” and “32 kHz Crystal Oscillator”, which do not exist. 5. Updated code examples on page 44. 6. Removed ADHSM bit. 7. Renamed Port D pin ICP to ICP1. See “Alternate Functions of Port D” on page 64. 8. Added information about PWM symmetry for Timer 0 on page 79 and Timer 2 on page 126. 9. Updated Table 68 on page 169, Table 75 on page 190, Table 76 on page 193, Table 77 on page 196, Table 108 on page 253, Table 113 on page 261. 10. Updated description on “Bit 5 – TWSTA: TWI START Condition Bit” on page 182. 11. Updated the description in “Filling the Temporary Buffer (Page Loading)” and “Performing a Page Write” on page 231. 12. Removed the section description in “SPI Serial Programming Characteristics” on page 254. 13. Updated “Electrical Characteristics” on page 255. ATmega8535(L) 312 2502K–AVR–10/06
ATmega8535(L) 14. Updated “ADC Characteristics” on page 263. 14. Updated “Register Summary” on page 299. 15. Various Timer 1 corrections. 16. Added WD_FUSE period in Table 108 on page 253. Changes from Rev. 1. Canged the Endurance on the Flash to 10,000 Write/Erase Cycles. 2502A-06/02 to Rev. 2502B-09/02 313 2502K–AVR–10/06
ATmega8535(L) 314 2502K–AVR–10/06
ATmega8535(L) Table of Contents Features................................................................................................ 1 Pin Configurations............................................................................... 2 Disclaimer............................................................................................................. 2 Overview............................................................................................... 3 Block Diagram...................................................................................................... 3 AT90S8535 Compatibility..................................................................................... 4 Pin Descriptions.................................................................................................... 5 Resources ............................................................................................ 6 About Code Examples......................................................................... 7 AVR CPU Core ..................................................................................... 8 Introduction........................................................................................................... 8 Architectural Overview.......................................................................................... 8 ALU – Arithmetic Logic Unit.................................................................................. 9 Status Register................................................................................................... 10 General Purpose Register File........................................................................... 11 Stack Pointer...................................................................................................... 12 Instruction Execution Timing............................................................................... 13 Reset and Interrupt Handling.............................................................................. 13 AVR ATmega8535 Memories............................................................ 16 In-System Reprogrammable Flash Program Memory........................................ 16 SRAM Data Memory........................................................................................... 17 EEPROM Data Memory...................................................................................... 18 I/O Memory......................................................................................................... 23 System Clock and Clock Options .................................................... 24 Clock Systems and their Distribution.................................................................. 24 Clock Sources..................................................................................................... 25 Default Clock Source.......................................................................................... 25 Crystal Oscillator................................................................................................. 25 Low-frequency Crystal Oscillator........................................................................ 28 External RC Oscillator........................................................................................ 28 Calibrated Internal RC Oscillator........................................................................ 29 External Clock..................................................................................................... 31 Timer/Counter Oscillator..................................................................................... 31 Power Management and Sleep Modes............................................. 32 Idle Mode............................................................................................................ 33 ADC Noise Reduction Mode............................................................................... 33 Power-down Mode.............................................................................................. 33 Power-save Mode............................................................................................... 33 i 2502K–AVR–10/06
Standby Mode..................................................................................................... 34 Extended Standby Mode.................................................................................... 34 Minimizing Power Consumption......................................................................... 35 System Control and Reset................................................................ 36 Internal Voltage Reference................................................................................. 41 Watchdog Timer................................................................................................. 41 Timed Sequences for Changing the Configuration of the Watchdog Timer....... 45 Interrupts............................................................................................ 46 Interrupt Vectors in ATmega8535....................................................................... 46 I/O-Ports.............................................................................................. 51 Introduction......................................................................................................... 51 Ports as General Digital I/O................................................................................ 52 Alternate Port Functions..................................................................................... 57 Register Description for I/O-Ports....................................................................... 66 External Interrupts............................................................................. 68 8-bit Timer/Counter0 with PWM........................................................ 71 Overview............................................................................................................. 71 Timer/Counter Clock Sources............................................................................. 72 Counter Unit........................................................................................................ 72 Output Compare Unit.......................................................................................... 73 Compare Match Output Unit............................................................................... 75 Modes of Operation............................................................................................ 76 Timer/Counter Timing Diagrams......................................................................... 80 8-bit Timer/Counter Register Description........................................................... 83 Timer/Counter0 and Timer/Counter1 Prescalers............................ 87 16-bit Timer/Counter1........................................................................ 89 Overview............................................................................................................. 89 Accessing 16-bit Registers................................................................................. 92 Timer/Counter Clock Sources............................................................................. 95 Counter Unit........................................................................................................ 95 Input Capture Unit............................................................................................... 96 Output Compare Units........................................................................................ 98 Compare Match Output Unit............................................................................. 100 Modes of Operation.......................................................................................... 101 Timer/Counter Timing Diagrams....................................................................... 108 16-bit Timer/Counter Register Description....................................................... 110 8-bit Timer/Counter2 with PWM and Asynchronous Operation.. 117 ATmega8535(L) ii 2502K–AVR–10/06
ATmega8535(L) Overview........................................................................................................... 117 Timer/Counter Clock Sources........................................................................... 118 Counter Unit...................................................................................................... 119 Output Compare Unit........................................................................................ 119 Compare Match Output Unit............................................................................. 121 Modes of Operation.......................................................................................... 122 Timer/Counter Timing Diagrams....................................................................... 126 8-bit Timer/Counter Register Description......................................................... 128 Asynchronous Operation of the Timer/Counter................................................ 131 Timer/Counter Prescaler................................................................................... 134 Serial Peripheral Interface – SPI..................................................... 136 SS Pin Functionality.......................................................................................... 141 Data Modes...................................................................................................... 144 USART .............................................................................................. 145 Overview........................................................................................................... 145 Clock Generation.............................................................................................. 146 Frame Formats................................................................................................. 149 USART Initialization.......................................................................................... 150 Data Transmission – The USART Transmitter................................................. 152 Data Reception – The USART Receiver.......................................................... 155 Asynchronous Data Reception......................................................................... 158 Multi-processor Communication Mode............................................................. 162 Accessing UBRRH/UCSRC Registers.............................................................. 163 USART Register Description............................................................................ 164 Examples of Baud Rate Setting........................................................................ 170 Two-wire Serial Interface ................................................................ 174 Features............................................................................................................ 174 Two-wire Serial Interface Bus Definition........................................................... 174 Data Transfer and Frame Format..................................................................... 175 Multi-master Bus Systems, Arbitration and Synchronization............................ 177 Overview of the TWI Module............................................................................ 179 TWI Register Description.................................................................................. 181 Using the TWI................................................................................................... 185 Transmission Modes......................................................................................... 188 Multi-master Systems and Arbitration............................................................... 201 Analog Comparator......................................................................... 203 Analog Comparator Multiplexed Input.............................................................. 205 Analog-to-Digital Converter............................................................ 206 Features............................................................................................................ 206 Operation.......................................................................................................... 207 Starting a Conversion....................................................................................... 208 iii 2502K–AVR–10/06
Prescaling and Conversion Timing................................................................... 209 Changing Channel or Reference Selection...................................................... 212 ADC Noise Canceler......................................................................................... 214 ADC Conversion Result.................................................................................... 218 Boot Loader Support – Read-While-Write Self-Programming..... 224 Boot Loader Features....................................................................................... 224 Application and Boot Loader Flash Sections.................................................... 224 Read-While-Write and No Read-While-Write Flash Sections........................... 224 Boot Loader Lock Bits....................................................................................... 226 Entering the Boot Loader Program................................................................... 227 Addressing the Flash during Self-Programming............................................... 229 Self-Programming the Flash............................................................................. 230 Memory Programming..................................................................... 237 Program And Data Memory Lock Bits.............................................................. 237 Fuse Bits........................................................................................................... 238 Signature Bytes................................................................................................ 239 Calibration Byte................................................................................................ 239 Parallel Programming Parameters, Pin Mapping, and Commands.................. 240 Parallel Programming....................................................................................... 242 Serial Downloading........................................................................................... 251 Electrical Characteristics................................................................ 255 Absolute Maximum Ratings*............................................................................. 255 DC Characteristics............................................................................................ 255 External Clock Drive Waveforms...................................................................... 258 External Clock Drive......................................................................................... 258 Two-wire Serial Interface Characteristics......................................................... 259 SPI Timing Characteristics............................................................................... 261 ADC Characteristics......................................................................................... 263 ATmega8535 Typical Characteristics............................................ 266 Register Summary........................................................................... 299 Instruction Set Summary................................................................ 301 Ordering Information....................................................................... 304 Packaging Information.................................................................... 306 44A................................................................................................................... 306 40P6................................................................................................................. 307 44J.................................................................................................................... 308 44M1-A............................................................................................................. 309 ATmega8535(L) iv 2502K–AVR–10/06
ATmega8535(L) Errata ................................................................................................ 310 ATmega8535 Rev. A and B..................................................................................................... 310 Datasheet Revision History............................................................ 311 Changes from Rev. 2502J- 08/06 to Rev. 2502K- 10/06.................................. 311 Changes from Rev. 2502I- 06/06 to Rev. 2502J- 08/06................................... 311 Changes from Rev. 2502H- 04/06 to Rev. 2502I- 06/06.................................. 311 Changes from Rev. 2502G- 04/05 to Rev. 2502H- 04/06................................. 311 Changes from Rev. 2502F- 06/04 to Rev. 2502G- 04/05................................. 311 Changes from Rev. 2502E-12/03 to Rev. 2502G-06/04................................... 311 Changes from Rev. 2502E-12/03 to Rev. 2502F-06/04................................... 311 Changes from Rev. 2502D-09/03 to Rev. 2502E-12/03................................... 311 Changes from Rev. 2502C-04/03 to Rev. 2502D-09/03................................... 312 Changes from Rev. 2502B-09/02 to Rev. 2502C-04/03................................... 312 Changes from Rev. 2502A-06/02 to Rev. 2502B-09/02................................... 313 Table of Contents ................................................................................. i v 2502K–AVR–10/06
ATmega8535(L) vi 2502K–AVR–10/06
Atmel Corporation Atmel Operations 2325 Orchard Parkway Memory RF/Automotive San Jose, CA 95131, USA 2325 Orchard Parkway Theresienstrasse 2 Tel: 1(408) 441-0311 San Jose, CA 95131, USA Postfach 3535 Fax: 1(408) 487-2600 Tel: 1(408) 441-0311 74025 Heilbronn, Germany Fax: 1(408) 436-4314 Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 Regional Headquarters Microcontrollers Europe 2325 Orchard Parkway 1150 East Cheyenne Mtn. Blvd. Atmel Sarl San Jose, CA 95131, USA Colorado Springs, CO 80906, USA Route des Arsenaux 41 Tel: 1(408) 441-0311 Tel: 1(719) 576-3300 Case Postale 80 Fax: 1(408) 436-4314 Fax: 1(719) 540-1759 CH-1705 Fribourg La Chantrerie Biometrics/Imaging/Hi-Rel MPU/ Switzerland BP 70602 High Speed Converters/RF Datacom Tel: (41) 26-426-5555 44306 Nantes Cedex 3, France Avenue de Rochepleine Fax: (41) 26-426-5500 Tel: (33) 2-40-18-18-18 BP 123 Asia Fax: (33) 2-40-18-19-60 38521 Saint-Egreve Cedex, France Room 1219 Tel: (33) 4-76-58-30-00 Chinachem Golden Plaza ASIC/ASSP/Smart Cards Fax: (33) 4-76-58-34-80 Zone Industrielle 77 Mody Road Tsimshatsui 13106 Rousset Cedex, France East Kowloon Tel: (33) 4-42-53-60-00 Hong Kong Fax: (33) 4-42-53-60-01 Tel: (852) 2721-9778 Fax: (852) 2722-1369 1150 East Cheyenne Mtn. Blvd. Japan Colorado Springs, CO 80906, USA 9F, Tonetsu Shinkawa Bldg. Tel: 1(719) 576-3300 1-24-8 Shinkawa Fax: 1(719) 540-1759 Chuo-ku, Tokyo 104-0033 Japan Scottish Enterprise Technology Park Tel: (81) 3-3523-3551 Maxwell Building Fax: (81) 3-3523-7581 East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise,to any intellectualproperty right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representationsor warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustainlife. © 2006 Atmel Corporation. All rights reserved. Atmel®, logo and combinations thereof, Everywhere You Are®, AVR®, and others are the trade- marks or registered trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 2502K–AVR–10/06
Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: M icrochip: ATMEGA8535-16JC ATMEGA8535-16AI ATMEGA8535L-8AI ATMEGA8535L-8AC ATMEGA8535-16AUR ATMEGA8535-16JUR ATMEGA8535-16MUR ATMEGA8535L-8AUR ATMEGA8535L-8JUR ATMEGA8535L-8MUR ATmega8535L-8PC ATmega8535L-8JC ATmega8535L-8MC ATmega8535L-8PI ATmega8535L-8JI ATmega8535L- 8MI ATmega8535L-8AU ATmega8535L-8PU ATmega8535L-8MU ATmega8535-16AC ATmega8535-16PC ATmega8535-16MC ATmega8535-16PI ATmega8535-16JI ATmega8535-16MI ATmega8535-16AU ATmega8535- 16PU ATmega8535-16MU ATMEGA8535L-8JU ATMEGA8535-16JU ATMEGA8535-W