SAM9M11 Atmel | SMART ARM-based Embedded MPU DATASHEET Description The Atmel® | SMART SAM9M11 is a multimedia enabled mid-range ARM926- based embedded MPU running at 400 MHz, combining user interfaces, video playback and connectivity. It includes hardware video decoder, LCD controller, resistive touchscreen, camera interface, audio, Ethernet 10/100 and high speed USB and SDIO. The hardware video decoder supports the standards H.264, MPEG-4, MPEG-2, VC-1, and H.263. The SAM9M11 also provides hardware image post-processing, such as image scaling, color conversion and image rotation. The SAM9M11 supports DDR2 and NAND Flash memory interfaces for program and data storage. An internal 133 MHz multi-layer bus architecture associated with 39 DMA channels, a dual external bus interface and distributed memory including a 64 Kbyte SRAM which can be configured as a tightly coupled memory (TCM) sustains the high bandwidth required by the processor and the high speed peripherals. On-chip hardware accelerators with DMA support enable high-speed data encryption and authentication of the transferred data or application. Supported standards are up to 256-bit AES, FIPS PUB 46-3 compliant TDES and FIPS Publication 180-2 compliant SHA1 and SHA256. A True Random Number Generator is embedded for key generation and exchange protocols. The I/Os support 1.8V or 3.3V operation, which are independently configurable for the memory interface and peripheral I/Os. This feature completely eliminates the need for any external level shifters. In addition it supports a 0.8 ball mm pitch package for low cost PCB manufacturing. The SAM9M11 devices have three software-selectable low-power modes: Idle, Ultra Low-power and Backup. In Idle mode, the processor is stopped while all other functions can be kept running at normal operating bus frequency. In Ultra Low-power mode, the processor is stopped while all other functions can be kept running at minimum operating bus frequency. In Backup mode, only the real-time clock, real-time timer, 128-bit general purpose backup registers, and wake-up logic are running. The SAM9M11 power management controller features efficient clock gating and a battery backup section minimizing power consumption in active and standby modes. The SAM9M11 device is particularly well suited for media-rich displays and control panels in home and commercial buildings, POS terminals, entertainment systems, internet appliances and medical applications. Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Features  400 MHz ARM926EJ-S™ ARM® Thumb® Processor ̶ 32 Kbytes Data Cache, 32 Kbytes Instruction Cache, MMU  Memories ̶ 4-port, 4-bank DDR2/LPDDR Controller ̶ External Bus Interface supporting 4-bank DDR2/LPDDR, SDR/LPSDR, Static Memories, CompactFlash®, SLC NAND Flash with ECC ̶ 64 Kbyte internal SRAM, single-cycle access at system speed or processor speed through TCM interface ̶ 64 Kbyte internal ROM, embedding bootstrap routine  System ̶ 133 MHz twelve 32-bit layer AHB Bus Matrix ̶ 39 DMA Channels ̶ Boot from NAND Flash, SDCard, DataFlash or serial DataFlash ̶ Reset Controller (RSTC) with on-chip Power-on Reset ̶ Selectable 32768 Hz Low-power and 12 MHz Crystal Oscillators ̶ Internal Low-power 32 kHz RC Oscillator ̶ One PLL for the system and one 480 MHz PLL optimized for USB High Speed ̶ Two Programmable External Clock Signals ̶ Advanced Interrupt Controller (AIC) ̶ Periodic Interval Timer (PIT), Watchdog Timer (WDT), Real-time Timer (RTT), and Real-time Clock (RTC)  Three Low-power Modes: Idle, Ultra Low-power, and Backup  Peripherals ̶ Universal Video Decoder (VDEC) – decoding at up to 30fps at D1 (720x576pixels) or WVGA (800x480) resolution ̶ LCD Controller (LCDC) supporting STN and TFT displays up to 1280*860 ̶ ITU-R BT. 601/656 Image Sensor Interface (ISI) ̶ Dual High Speed USB Host and a High Speed USB Device with On-Chip Transceivers ̶ 10/100 Mbps Ethernet MAC Controller (EMAC) ̶ Two High Speed Memory Card Hosts (SDIO, SDCard, MMC and CE-ATA) ̶ AC’97 Controller (AC97C) ̶ Two Master/Slave Serial Peripheral Interfaces (SPI) ̶ 2 Three-channel 16-bit Timer Counters (TC) ̶ Two Synchronous Serial Controllers (I2S mode) ̶ Four-channel 16-bit PWM Controller ̶ 2 Two-wire Interfaces (TWI) ̶ Four USARTs with ISO7816, IrDA, Manchester and SPI modes, one DBGU ̶ 8-channel 10-bit ADC controller with 4-wire Touchscreen support (TSADCC) ̶ Write Protected Registers  Cryptography ̶ True Random Number Generator (TRNG) ̶ AES256-, 192-, 128-bit Key Algorithm ̶ TDES Compliant with FIPS PUB 46-3 Specifications ̶ SHA (SHA1 and SHA256) Compliant with FIPS Publication 180-2  I/O ̶ Five 32-bit Parallel Input/Output Controllers ̶ 160 Programmable I/O Lines Multiplexed with up to Two Peripheral I/Os with Schmitt trigger input  Package ̶ 324-ball TFBGA – 15 x 15 x 1.2 mm, 0.8 mm pitch 2 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

1. Block Diagram Figure 1-1. SAM9M11 Block Diagram NTRST TDITDOTMSTCKRTCK JTAGSEL BMS HFSDHPHA,S DHPFA,S DHMHASVDBMGADFSDDP/HHSFDSP/DHPBH, LSDDCFPDSBD,LD 0CD–M/DLHHVCSLFSDDSCYDMDD/N2DMH3CL,BHO DLTSDCCDELKDMNC,HB DSLPYCINDWSICCR,_ CLDI0CS–IID_SMIPI_OCSDDIK1_1IHSSIY_NVICSSIY_NMCCKETXCEKT–XEERENXC–CREKSTE–XREEXCREEORRL–XE0E–RTEXXRD0XV–E3EMTDXE3CMDIO TST System Controller JTAG / Boundary Scan TranHscSe iver TranHscSe iver PIO PCK0–PCK1 DDR_A0–DDR_A13 FIQ AIC In-Circuit Emulator PA PB DDR_D0–DDR_D15 IRQ P DDR_VREF DDRTXXDD IO DPBDGCU ICaAcRheM926EJ-SD Cache UHSSB E HHoCsIt HDSe vUicSeB LCD ISI EMAC 8-cDhaMnAnel DDR2 DDDDRR__DDQQSM[[00....11]] 32 Kbytes MMU 32 Kbytes LPDDR DDR_CS PLLRCA PLLA ITCMDTCM Bus Interface DMA DMA DMA DMA DMA DDR_CLK, #DDR_CLK PLLUTMI PMC I D DDDDRR__CRKAES, DDR_CAS XIN OSC12M DDR_WE XOUT DDR_BA0, DDR_BA1 WDT PIT SRAM 64 KB Backup Section D0–D15 RC 1G2P8B-bRit EBI AA01//NNBBSS02/NWR2 XOXUINT3322 OSC 32K RTT Multi-Layer AHB Matrix DDR2/ AA21–6A/B1A50, A18 SHDN SHDWC RTC LPDDR/ A17/BA1 WKUP SDRAM NCS1/SDCS VDNDRBSUT POR RSTC Video Controller SRSDDAWCS,KE C,, #ASSSDDAC1K0, SDCKE VDDCORE POR Decoder DQM[0..1] PIOA PIOD ROM TDES SHA Peripheral Peripheral + NAND Flash DQS[0..1] Atm PIOB PIOE 64 KB AES PDC PDC TRNG Bridge CoDnMtroAller ProPceosssting CoEnCtroCller NNRWDR0/NWE el-64 PIOC NNWWRR13//NNBBSS13 37 APB NCS0 H-A S CF NANDOE, NANDWE TARM-SAM9M11-D AM9M11 [D MSCCDIE0/FS /AMIDFTCIAOOI1 TTWWII01 UUUUPSSSSDAAAACRRRRTTTT0123 P4W-cMh TTTCCC012 TTTCCC345 SSPPPDII1C0 SSPSSDCCC01 APCD9C7 8-cfhoar nTnoPeuDlc 1Ch0s-cbreit eAnDC CMoSentmtartooiclrleyr NNNDDAA12CCW1Q956SSMA–/–C54I[ADT2//FCC23.R.4FF13NCC]WSS10 a A CFCE1–CFCE2 tashe TA PIO NNCCSS23/NANDCS e S t_1 H 7-D E ec-15 ET] MCI0_MDCIA00_–CMDCMIA,0CMI_M0CDCI_I1A1C_7_KD,CAMD0CA–I1M_CIC1K_DTA7WTDW0C–KT0W–DT1WCCKT1S0R–TCST0SS–C3RKT0RS–D3SXC0T–KX3RDD0X–3TXPD3WM0–PWTMC3LKT0I–OTATCI0L–OKTBI2T0OC–ALTI2KT3OI–BOT2ATCI3L–OKTBI53O–ATI5OB5NPCNSSP3PCSNI20P_CNS,P 1SCSPS0PI1C_KMOSIMISTKO0–TTFKS01–TSTDFC01–R0TD_D01–,R RSFD0S1–RCRKF011–_RAK1C97ACCK97AFCS97ARC9X7TTXSADTRAGD0XAPD1XMAD2GYPAPADD34Y–MGPTASDA7DVRVEDFDAGNNADANA 3

2. Signal Description Table 2-1 gives details on the signal names classified by peripheral. Table 2-1. Signal Description List Active Reference Signal Name Function Type Level Voltage Comments Power Supplies VDDIOM0 DDR2 I/O Lines Power Supply Power – – 1.65V to 1.95V VDDIOM1 EBI I/O Lines Power Supply Power – – 1.65V to 1.95V or 3.0V to 3.6V VDDIOP0 Peripherals I/O Lines Power Supply Power – – 1.65V to 3.6V VDDIOP1 Peripherals I/O Lines Power Supply Power – – 1.65V to 3.6V VDDIOP2 ISI I/O Lines Power Supply Power – – 1.65V to 3.6V VDDBU Backup I/O Lines Power Supply Power – – 1.8V to 3.6V VDDANA Analog Power Supply Power – – 3.0V to 3.6V VDDPLLA PLLA Power Supply Power – – 0.9V to 1.1V VDDPLLUTMI PLLUTMI Power Supply Power – – 0.9V to 1.1V VDDOSC Oscillator Power Supply Power – – 1.65V to 3.6V VDDCORE Core Chip Power Supply Power – – 0.9V to 1.1V UDPHS and UHPHS UTMI+ Core VDDUTMIC Power – – 0.9V to 1.1V Power Supply UDPHS and UHPHS UTMI+ Interface VDDUTMII Power – – 3.0V to 3.6V Power Supply GNDIOM DDR2 and EBI I/O Lines Ground Ground – – – GNDIOP Peripherals and ISI I/O Lines Ground Ground – – – GNDCORE Core Chip Ground Ground – – – PLLA, PLLUTMI and Oscillator GNDOSC Ground – – – Ground GNDBU Backup Ground Ground – – – UDPHS and UHPHS UTMI+ Core and GNDUTMI Ground – – – Interface Ground GNDANA Analog Ground Ground – – – Clocks, Oscillators and PLLs XIN Main Oscillator Input Input – – – XOUT Main Oscillator Output Output – – – XIN32 Slow Clock Oscillator Input Input – – – XOUT32 Slow Clock Oscillator Output Output – – – VBG Bias Voltage Reference for USB Analog – – – PCK0–PCK1 Programmable Clock Output Output – (1) – 4 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 2-1. Signal Description List (Continued) Active Reference Signal Name Function Type Level Voltage Comments Shutdown, Wakeup Logic Driven at 0V only. 0: The device is in backup mode SHDN Shutdown Control Output – VDDBU 1: The device is running (not in backup mode). WKUP Wake-Up Input Input – VDDBU Accepts between 0V and VDDBU ICE and JTAG TCK Test Clock Input – VDDIOP0 No pull-up resistor, Schmitt trigger TDI Test Data In Input – VDDIOP0 No pull-up resistor, Schmitt trigger TDO Test Data Out Output – VDDIOP0 TMS Test Mode Select Input – VDDIOP0 No pull-up resistor, Schmitt trigger JTAGSEL JTAG Selection Input – VDDBU Pull-down resistor (15 kΩ) RTCK Return Test Clock Output – VDDIOP0 Reset/Test Open drain output NRST Microcontroller Reset (2) I/O Low VDDIOP0 Pull-up resistor (100 kΩ), Schmitt trigger Pull-down resistor (15 kΩ), TST Test Mode Select Input – VDDBU Schmitt trigger Pull-up resistor (100 kΩ), Schmitt NTRST Test Reset Signal Input – VDDIOP0 trigger Must be connected to GND or BMS Boot Mode Select Input – VDDIOP0 VDDIOP0 Debug Unit - DBGU DRXD Debug Receive Data Input – (1) – DTXD Debug Transmit Data Output – (1) – Advanced Interrupt Controller - AIC IRQ External Interrupt Input Input – (1) – FIQ Fast Interrupt Input Input – (1) – PIO Controller - PIOA / PIOB / PIOC / PIOD / PIOE PA0–PA31 Parallel IO Controller A I/O – (1) PB0–PB31 Parallel IO Controller B I/O – (1) Pulled-up input at reset PC0–PC31 Parallel IO Controller C I/O – (1) (100kΩ)(3), Schmitt trigger PD0–PD31 Parallel IO Controller D I/O – (1) PE0–PE31 Parallel IO Controller E I/O – (1) SAM9M11 [DATASHEET] 5 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 2-1. Signal Description List (Continued) Active Reference Signal Name Function Type Level Voltage Comments DDR Memory Interface - DDR2/LPDDR Controller - DDRSDRC0 DDR_D0–DDR_D15 Data Bus I/O – VDDIOM0 Pulled-up input at reset DDR_A0–DDR_A13 Address Bus Output – VDDIOM0 0 at reset DDR_CLK-#DDR_CLK DDR differential clock input Output – VDDIOM0 – DDR_CKE DDR Clock Enable Output High VDDIOM0 – DDR_CS DDR Chip Select Output Low VDDIOM0 – DDR_WE DDR Write Enable Output Low VDDIOM0 – DDR_RAS-DDR_CAS Row and Column Signal Output Low VDDIOM0 – DDR_DQM[0..1] Write Data Mask Output – VDDIOM0 – DDR_DQS[0..1] Data Strobe Output – VDDIOM0 – DDR_BA0–DDR_BA1 Bank Select Output – VDDIOM0 – DDR_VREF Reference Voltage Input – VDDIOM0 – External Bus Interface - EBI D0 -D31 Data Bus I/O – VDDIOM1 Pulled-up input at reset A0–A25 Address Bus Output – VDDIOM1 0 at reset NWAIT External Wait Signal Input Low VDDIOM1 – Static Memory Controller - SMC NCS0–NCS5 Chip Select Lines Output Low VDDIOM1 – NWR0–NWR3 Write Signal Output Low VDDIOM1 – NRD Read Signal Output Low VDDIOM1 – NWE Write Enable Output Low VDDIOM1 – NBS0–NBS3 Byte Mask Signal Output Low VDDIOM1 – CompactFlash Support CFCE1–CFCE2 CompactFlash Chip Enable Output Low VDDIOM1 – CFOE CompactFlash Output Enable Output Low VDDIOM1 – CFWE CompactFlash Write Enable Output Low VDDIOM1 – CFIOR CompactFlash IO Read Output Low VDDIOM1 – CFIOW CompactFlash IO Write Output Low VDDIOM1 – CFRNW CompactFlash Read Not Write Output – VDDIOM1 – CFCS0–CFCS1 CompactFlash Chip Select Lines Output Low VDDIOM1 – NAND Flash Support NANDCS NAND Flash Chip Select Output Low VDDIOM1 – NANDOE NAND Flash Output Enable Output Low VDDIOM1 – NANDWE NAND Flash Write Enable Output Low VDDIOM1 – 6 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 2-1. Signal Description List (Continued) Active Reference Signal Name Function Type Level Voltage Comments EBI - DDR2/SDRAM/LPDDR Controller - DDRSDRC1 SDCK, #SDCK DDR2/SDRAM differential clock Output – VDDIOM1 – SDCKE DDR2/SDRAM Clock Enable Output High VDDIOM1 – SDCS DDR2/SDRAM Controller Chip Select Output Low VDDIOM1 – BA0–BA1 Bank Select Output – VDDIOM1 – SDWE DDR2/SDRAM Write Enable Output Low VDDIOM1 – RAS - CAS Row and Column Signal Output Low VDDIOM1 – SDA10 SDRAM Address 10 Line Output – VDDIOM1 – DQS[0..1] Data Strobe Output – VDDIOM1 – DQM[0..3] Write Data Mask Output – VDDIOM1 – High Speed Multimedia Card Interface - HSMCIx MCIx_CK Multimedia Card Clock I/O – (1) – MCIx_CDA Multimedia Card Slot A Command I/O – (1) – MCIx_DA0–MCIx_DA7 Multimedia Card Slot A Data I/O – (1) – Universal Synchronous Asynchronous Receiver Transmitter - USARTx SCKx USARTx Serial Clock I/O – (1) – TXDx USARTx Transmit Data Output – (1) – RXDx USARTx Receive Data Input – (1) – RTSx USARTx Request To Send Output – (1) – CTSx USARTx Clear To Send Input – (1) – Synchronous Serial Controller - SSCx TDx SSC Transmit Data Output – (1) – RDx SSC Receive Data Input – (1) – TKx SSC Transmit Clock I/O – (1) – RKx SSC Receive Clock I/O – (1) – TFx SSC Transmit Frame Sync I/O – (1) – RFx SSC Receive Frame Sync I/O – (1) – AC97 Controller - AC97C AC97RX AC97 Receive Signal Input – (1) – AC97TX AC97 Transmit Signal Output – (1) – AC97FS AC97 Frame Synchronization Signal Output – (1) – AC97CK AC97 Clock signal Input – (1) – Time Counter - TCx TCLKx TC Channel x External Clock Input Input – (1) – TIOAx TC Channel x I/O Line A I/O – (1) – TIOBx TC Channel x I/O Line B I/O – (1) – SAM9M11 [DATASHEET] 7 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 2-1. Signal Description List (Continued) Active Reference Signal Name Function Type Level Voltage Comments Pulse Width Modulation Controller - PWM PWMx Pulse Width Modulation Output Output – (1) – Serial Peripheral Interface - SPIx_ SPIx_MISO Master In Slave Out I/O – (1) – SPIx_MOSI Master Out Slave In I/O – (1) – SPIx_SPCK SPI Serial Clock I/O – (1) – SPIx_NPCS0 SPI Peripheral Chip Select 0 I/O Low (1) – SPIx_NPCS1–SPIx_NPCS3 SPI Peripheral Chip Select Output Low (1) – Two-Wire Interface - TWI TWDx Two-wire Serial Data I/O – (1) – TWCKx Two-wire Serial Clock I/O – (1) – USB Host High Speed Port - UHPHS HFSDPA USB Host Port A Full Speed Data + Analog – VDDUTMII – HFSDMA USB Host Port A Full Speed Data - Analog – VDDUTMII – HHSDPA USB Host Port A High Speed Data + Analog – VDDUTMII – HHSDMA USB Host Port A High Speed Data - Analog – VDDUTMII – HFSDPB USB Host Port B Full Speed Data + Analog – VDDUTMII Multiplexed with DFSDP HFSDMB USB Host Port B Full Speed Data - Analog – VDDUTMII Multiplexed with DFSDM HHSDPB USB Host Port B High Speed Data + Analog – VDDUTMII Multiplexed with DHSDP HHSDMB USB Host Port B High Speed Data - Analog – VDDUTMII Multiplexed with DHSDM USB Device High Speed Port - UDPHS DFSDM USB Device Full Speed Data - Analog – VDDUTMII – DFSDP USB Device Full Speed Data + Analog – VDDUTMII – DHSDM USB Device High Speed Data - Analog – VDDUTMII – DHSDP USB Device High Speed Data + Analog – VDDUTMII – 8 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 2-1. Signal Description List (Continued) Active Reference Signal Name Function Type Level Voltage Comments Ethernet 10/100 - EMAC ETXCK Transmit Clock or Reference Clock Input – (1) MII only, REFCK in RMII ERXCK Receive Clock Input – (1) MII only ETXEN Transmit Enable Output – (1) – ETX0–ETX3 Transmit Data Output – (1) ETX0–ETX1 only in RMII ETXER Transmit Coding Error Output – (1) MII only ERXDV Receive Data Valid Input – (1) RXDV in MII, CRSDV in RMII ERX0–ERX3 Receive Data Input – (1) ERX0–ERX1 only in RMII ERXER Receive Error Input – (1) – ECRS Carrier Sense and Data Valid Input – (1) MII only ECOL Collision Detect Input – (1) MII only EMDC Management Data Clock Output – (1) – EMDIO Management Data Input/Output I/O – (1) – Image Sensor Interface - ISI ISI_D0–ISI_D11 Image Sensor Data Input – VDDIOP2 – ISI_MCK Image sensor Reference clock output – VDDIOP2 – ISI_HSYNC Image Sensor Horizontal Synchro input – VDDIOP2 – ISI_VSYNC Image Sensor Vertical Synchro input – VDDIOP2 – ISI_PCK Image Sensor Data clock input – VDDIOP2 – LCD Controller - LCDC LCDD0–LCDD23 LCD Data Bus Output – VDDIOP1 – LCDVSYNC LCD Vertical Synchronization Output – VDDIOP1 – LCDHSYNC LCD Horizontal Synchronization Output – VDDIOP1 – LCDDOTCK LCD Dot Clock Output – VDDIOP1 – LCDDEN LCD Data Enable Output – VDDIOP1 – LCDCC LCD Contrast Control Output – VDDIOP1 – LCDPWR LCD panel Power enable control Output – VDDIOP1 – LCDMOD LCD Modulation signal Output – VDDIOP1 – SAM9M11 [DATASHEET] 9 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 2-1. Signal Description List (Continued) Active Reference Signal Name Function Type Level Voltage Comments Touchscreen Analog-to-Digital Converter Controller - TSADCC Analog input channel 0 or AD0X Analog – VDDANA Multiplexed with AD0 P TouchScreen Top channel Analog input channel 1 or AD1X Analog – VDDANA Multiplexed with AD1 M TouchScreen Bottom channel Analog input channel 2 or AD2Y Analog – VDDANA Multiplexed with AD2 P TouchScreen Right channel Analog input channel 3 or AD3Y Analog – VDDANA Multiplexed with AD3 M TouchScreen Left channel GPAD4–GPAD7 Analog Inputs Analog – VDDANA – TSADTRG ADC Trigger Input – VDDANA – TSADVREF ADC Reference Analog – VDDANA – Notes: 1. Refer to peripheral multiplexing tables in Section 7.4 “Peripheral Signals Multiplexing on I/O Lines” for these signals. 2. When configured as an input, the NRST pin enables asynchronous reset of the device when asserted low. This allows connection of a simple push button on the NRST pin as a system-user reset. 3. Programming of this pull-up resistor is performed independently for each I/O line through the PIO Controllers. After reset, all the I/O lines default as inputs with pull-up resistors enabled, except those which are multiplexed with the External Bus Interface signals that require to be enabled as Peripheral at reset. This is explicitly indicated in the column “Reset State” of the peripheral multiplexing tables. 10 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

3. Package and Pinout The SAM9M11 is delivered in a 324-ball TFBGA Green-compliant package. 3.1 Mechanical Overview of the 324-ball TFBGA Package Figure 3-1 shows the orientation of the 324-ball TFBGA package. A detailed mechanical description is given in Section 50. “Mechanical Characteristics”. Figure 3-1. Orientation of the 324-ball TFBGA Package Bottom View V U T R P N M L K J H G F E D C B A 1 2 3 4 5 6 7 8 9101112131415161718 3.2 324-ball TFBGA Package Pinout Table 3-1. SAM9M11 Pinout for 324-ball TFBGA Package Pin Signal Name Pin Signal Name Pin Signal Name Pin Signal Name A1 PC27 E10 NANDWE K1 PE21 P10 TMS A2 PC28 E11 DQS1 K2 PE23 P11 VDDPLLA A3 PC25 E12 D13 K3 PE26 P12 PB20 A4 PC20 E13 D11 K4 PE22 P13 PB31 A5 PC12 E14 A4 K5 PE24 P14 DDR_D7 A6 PC7 E15 A8 K6 PE25 P15 DDR_D3 A7 PC5 E16 A9 K7 PE27 P16 DDR_D4 A8 PC0 E17 A7 K8 PE28 P17 DDR_D5 A9 NWR3/NBS3 E18 VDDCORE K9 VDDIOP0 P18 DDR_D10 A10 NCS0 F1 PD22 K10 VDDIOP0 R1 PA18 A11 DQS0 F2 PD24 K11 GNDIOM R2 PA20 A12 RAS F3 SHDN K12 GNDIOM R3 PA24 A13 SDCK F4 PE1 K13 VDDIOM0 R4 PA30 A14 NSDCK F5 PE3 K14 DDR_A7 R5 PB4 A15 D7 F6 VDDIOM1 K15 DDR_A8 R6 PB13 A16 DDR_VREF F7 PC19 K16 DDR_A9 R7 PD0 SAM9M11 [DATASHEET] 11 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 3-1. SAM9M11 Pinout for 324-ball TFBGA Package (Continued) Pin Signal Name Pin Signal Name Pin Signal Name Pin Signal Name A17 D0 F8 PC14 K17 DDR_A11 R8 PD9 A18 A14 F9 PC4 K18 DDR_A10 R9 PD18 B1 PC31 F10 NCS1/SDCS L1 PA0 R10 TDI B2 PC29 F11 NRD L2 PE30 R11 RTCK B3 PC30 F12 SDWE L3 PE29 R12 PB22 B4 PC22 F13 A0/NBS0 L4 PE31 R13 PB29 B5 PC17 F14 A1/NBS2/NWR2 L5 PA2 R14 DDR_D6 B6 PC10 F15 A3 L6 PA4 R15 DDR_D1 B7 PC11 F16 A6 L7 PA8 R16 DDR_D0 B8 PC2 F17 A5 L8 PD2 R17 HHSDMA B9 SDA10 F18 A2 L9 PD13 R18 HFSDMA B10 A17/BA1 G1 PD25 L10 PD29 T1 PA22 B11 DQM0 G2 PD23 L11 PD31 T2 PA25 B12 SDCKE G3 PE6 L12 VDDIOM0 T3 PA26 B13 D12 G4 PE0 L13 VDDIOM0 T4 PB0 B14 D8 G5 PE2 L14 DDR_A1 T5 PB6 B15 D4 G6 PE8 L15 DDR_A3 T6 PB16 B16 D3 G7 PE4 L16 DDR_A4 T7 PD1 B17 A15 G8 PE11 L17 DDR_A6 T8 PD11 B18 A13 G9 GNDCORE L18 DDR_A5 T9 PD19 C1 XIN32 G10 VDDIOM1 M1 PA1 T10 PD30 C2 GNDANA G11 VDDIOM1 M2 PA5 T11 BMS C3 WKUP G12 VDDCORE M3 PA6 T12 PB8 C4 PC26 G13 VDDCORE M4 PA7 T13 PB30 C5 PC21 G14 DDR_DQM0 M5 PA10 T14 DDR_D2 C6 PC15 G15 DDR_DQS1 M6 PA14 T15 PB21 C7 PC9 G16 DDR_BA1 M7 PB14 T16 PB23 C8 PC3 G17 DDR_BA0 M8 PD4 T17 HHSDPA C9 NWR0/NWE G18 DDR_DQS0 M9 PD15 T18 HFSDPA C10 A16/BA0 H1 PD26 M10 NRST U1 PA27 C11 CAS H2 PD27 M11 PB11 U2 PA29 C12 D15 H3 VDDIOP1 M12 PB25 U3 PA28 C13 D10 H4 PE13 M13 PB27 U4 PB3 C14 D6 H5 PE5 M14 VDDIOM0 U5 PB7 C15 D2 H6 PE7 M15 DDR_D14 U6 PB17 C16 GNDIOM H7 PE9 M16 DDR_D15 U7 PD7 C17 A18 H8 PE10 M17 DDR_A0 U8 PD10 12 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 3-1. SAM9M11 Pinout for 324-ball TFBGA Package (Continued) Pin Signal Name Pin Signal Name Pin Signal Name Pin Signal Name C18 A12 H9 GNDCORE M18 DDR_A2 U9 PD14 D1 XOUT32 H10 GNDIOP N1 PA3 U10 TCK D2 PD20 H11 VDDCORE N2 PA9 U11 VDDOSC D3 GNDBU H12 GNDIOM N3 PA12 U12 GNDOSC D4 VDDBU H13 GNDIOM N4 PA15 U13 PB10 D5 PC24 H14 DDR_CS N5 PA16 U14 PB26 D6 PC18 H15 DDR_WE N6 PA17 U15 HHSDPB/DHSDP D7 PC13 H16 DDR_DQM1 N7 PB18 U16 HHSDMB/DHSDM D8 PC6 H17 DDR_CAS N8 PD6 U17 GNDUTMI D9 NWR1/NBS1 H18 DDR_NCLK N9 PD16 U18 VDDUTMIC D10 NANDOE J1 PE19 N10 NTRST V1 PA31 D11 DQM1 J2 PE16 N11 PB9 V2 PB1 D12 D14 J3 PE14 N12 PB24 V3 PB2 D13 D9 J4 PE15 N13 PB28 V4 PB5 D14 D5 J5 PE12 N14 DDR_D13 V5 PB15 D15 D1 J6 PE17 N15 DDR_D8 V6 PD3 D16 VDDIOM1 J7 PE18 N16 DDR_D9 V7 PD5 D17 A11 J8 PE20 N17 DDR_D11 V8 PD12 D18 A10 J9 GNDCORE N18 DDR_D12 V9 PD17 E1 PD21 J10 GNDCORE P1 PA11 V10 TDO E2 TSADVREF J11 GNDIOP P2 PA13 V11 XOUT E3 VDDANA J12 GNDIOM P3 PA19 V12 XIN E4 JTAGSEL J13 GNDIOM P4 PA21 V13 VDDPLLUTMI E5 TST J14 DDR_A12 P5 PA23 V14 VDDIOP2 E6 PC23 J15 DDR_A13 P6 PB12 V15 HFSDPB/DFSDP E7 PC16 J16 DDR_CKE P7 PB19 V16 HFSDMB/DFSDM E8 PC8 J17 DDR_RAS P8 PD8 V17 VDDUTMII E9 PC1 J18 DDR_CLK P9 PD28 V18 VBG SAM9M11 [DATASHEET] 13 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

4. Power Considerations 4.1 Power Supplies The SAM9M11 has several types of power supply pins. Some supply pins share common ground (GND) pins whereas others have separate grounds. See Table 4-1. Table 4-1. SAM9M11 Power Supply Pins Pin(s) Item(s) powered Range Typical Ground Core, including the processor VDDCORE Embedded memories 0.9–1.1 V 1.0V GNDCORE Peripherals VDDIOM0 DDR2/LPDDR I/O lines 1.65–1.95 V 1.8V 1.65–1.95 V 1.8V GNDIOM VDDIOM1 External Bus Interface 1 I/O lines 3.0–3.6 V 3.3V 1.65–1.95 V 1.8V VDDIOP0, VDDIOP1, VDDIOP2 Peripherals I/O lines GNDIOP 3.0–3.6 V 3.3V Slow Clock oscillator VDDBU Internal RC oscillator 1.8–3.6 V – GNDBU Part of the System Controller VDDPLLUTMI PLLUTMI cell 0.9–1.1 V 1.0V VDDPLLA PLLA cell 0.9–1.1 V 1.0V GNDOSC VDDOSC Main Oscillator cells 1.65–3.6 V – USB device VDDUTMIC 0.9–1.1 V 1.0V Host UTMI+ core GNDUTMI USB device VDDUTMII 3.0–3.6 V 3.3V Host UTMI+ interface VDDANA Analog-to-Digital Converter 3.0–3.6 V 3.3V GNDANA 4.2 Power Sequence Requirements The SAM9M11 board design must comply with the guidelines described in Section 4.2.1 “Power-up Sequence” and Section 4.2.2 “Power-down Sequence” to guarantee reliable operation of the device. Any deviation from these sequences may lead to unpredictable results. 14 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

4.2.1 Power-up Sequence Figure 4-1. VDDCORE and VDDIO Constraints at Startup V (V) DD V V typ DDIO DDIO V > V V DDIO OH OH V > V DDIO IH V IH V V typ DDCORE DDCORE V T+ t <---- t ---><- t -><------------ t-----------> RST 1 2 Core Supply POR Output SLCK V and V are controlled by the internal PORs (Power-on Reset) to guarantee that these power sources DDCORE DDBU reach their target values prior to the release of POR.  VDDIOP must be ≥ VIH (refer to Table 48-2 “DC Characteristics” for more details) within (tRST+t1) after V has reached V DDCORE T+  V must reach V (refer to Table 48-2 “DC Characteristics” for more details) within (t + t + t ) after DDIOM OH RST 1 2 V has reached V DDCORE T+ ̶ t is a POR characteristic RST ̶ t = 3 × t 1 SLCK ̶ t = 16 × t 2 SLCK The t min (22 µs) is obtained for the maximum frequency of the internal RC oscillator (44kHz). SLCK ̶ t = 30 µs RST ̶ t = 66 µs 1 ̶ t = 352 µs 2 In conclusion, V and V must be established first, then V to ensure a reliable operation of the DDIOP DDIOM DDCORE device. V , V , V and V must be started at any time prior to V to ensure correct DDOSC DDPLL DDUTMII DDUTMIC DDCORE behavior of the ROM code. SAM9M11 [DATASHEET] 15 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

4.2.2 Power-down Sequence To ensure that the device does not operate outside the operating conditions defined in Section 4.1 “Power Supplies”, it is good practice to first place the device in reset state before removing its power supplies. No specific sequencing is required with respect to its supply channels as long as the NRST line is held active during the power-down phase. Figure 4-2. Recommended Power-down Sequence t RSTPD No specific order and no specific timing required NRST among the channels VDDCORE VDDIOM0 VDDIOM1 VDDIOP0-2 VDDBU VDDPLLUTMI VDDUTMIC VDDUTMII VDDPLLA VDDOSC VDDANA time 16 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

5. Memories Figure 5-1. SAM9M11 Memory Mapping Address Memory Space Internal Memory Mapping 0x0000 0000 0x0000 0000 Boot Memory (1) 1 Mbyte 0x0010 0000 Internal Memories 256 Mbytes Notes: 0x0020 0000 ITCM (2) 1 Mbyte 00xx01F0F0F0 F0F0F0F0 (d(12e))p CSeoanfndtw inbager eoR nOp rBMoMg, rSEa BmaInm1d_a NRbClEeSM0A oPr SRAM 0x0030 0000 DSTRCAMM (2) 11 MMbbyyttee EBI 0x0040 0000 ROM 1 Mbyte Chip Select 0 256 Mbytes 0x0050 0000 LCD User Interface 1 Mbyte 0x1FFF FFFF 0x0060 0000 0x2000 0000 UDPHS RAM 1 Mbyte 0x0070 0000 EBI Chip Select 1/ UHP OHCI 1 Mbyte DDRSDRC1 256 Mbytes Peripheral Mapping 0x0080 0000 Chip Select 0xF000 0000 0x0090 0000 UHP EHCI 1 Mbyte 00xx23F0F0F0 F0F0F0F0 Reserved 0x00A0 0000 VDEC 1 Mbyte Undefined Chip ESBeIlect 2 256 Mbytes 0xFFF7 8000 UDPHS 16 Kbytes 0x0FFF FFFF (Abort) 0x3FFF FFFF 0xFFF7 C000 0x4000 0000 EBI TC0, TC1, TC2 16 Kbytes Chip Select 3/ 256 Mbytes 0xFFF8 0000 NANDFlash MCI0 16 Kbytes 0x4FFF FFFF 0x5000 0000 EBI 0xFFF8 4000 Chip Select 4/ 256 Mbytes TWI0 16 Kbytes Compact Flash 0xFFF8 8000 0x5FFF FFFF Slot 0 TWI1 16 Kbytes System Controller Mapping 0x6000 0000 EBI 0xFFF8 C000 0xFFFF C000 Chip Select 5/ Compact Flash 256 Mbytes USART0 16 Kbytes Reserved 0x6FFF FFFF Slot 1 0xFFF9 0000 0x7000 0000 USART1 16 Kbytes 0xFFFF E200 DDRSDRC0 256 Mbytes 0xFFF9 4000 ECC 512 bytes Chip Select USART2 16 Kbytes 0xFFFF E400 0x7FFF FFFF DDRSDRC1 512 bytes 0x8000 0000 0xFFF9 8000 0xFFFF E600 USART3 16 Kbytes DDRSDRC0 512 bytes 0xFFF9 C000 0xFFFF E800 SSC0 16 Kbytes SMC 512 bytes 0xFFFF EA00 0xFFFA 0000 MATRIX 512 bytes SSC1 16 Kbytes 0xFFFF EC00 0xFFFA 4000 DMAC 512 bytes 0xFFFF EE00 SPI0 16 Kbytes DBGU 512 bytes 0xFFFA 8000 0xFFFF F000 SPI1 16 Kbytes AIC 512 bytes 0xFFFA C000 0xFFFF F200 PIOA 512 bytes AC97 16 Kbytes 0xFFFF F400 0xFFFB 0000 PIOB 512 bytes Undefined 1,792 Mbytes TSADCC 16 Kbytes 0xFFFF F600 (Abort) 0xFFFB 4000 PIOC 512 bytes 0xFFFF F800 ISI 16 Kbytes 0xFFFB 8000 PIOD 512 bytes PWM 16 Kbytes 0xFFFF FA00 PIOE 512 bytes 0xFFFB C000 EMAC 16 Kbytes 0xFFFF FC00 PMC 256 bytes 0xFFFC 0000 0xFFFF FD00 AES 16 Kbytes RSTC 16 bytes 0xFFFC 4000 0xFFFF FD10 TDES 16 Kbytes 0xFFFF FD20 SHDWC 16 bytes 0xFFFC 8000 RTT 16 bytes SHA 16 Kbytes 0xFFFF FD30 0xFFFC C000 PIT 16 bytes 0xFFFF FD40 TRNG 16 Kbytes WDT 16 bytes 0xFFFD 0000 0xFFFF FD50 00xxEFF0F0F0 F0F0F0F0 0xFFFD 4000 MCI1 16 Kbytes 0xFFFF FD60 SGCPKBCRR 1166 bbyytteess TC3, TC4, TC5 16 Kbytes 0xFFFF FD70 Reserved Internal Peripherals 256 Mbytes 0xFFFD 8000 Reserved 0xFFFF FDB0 RTC 16 bytes 0xFFFF FDC0 0xFFFF FFFF 0xFFFF C000 Reserved System Controller 0xFFFF FFFF 0xFFFF FFFF SAM9M11 [DATASHEET] 17 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

5.1 Memory Mapping A first level of address decoding is performed by the AHB Bus Matrix, i.e., the implementation of the Advanced High performance Bus (AHB) for its Master and Slave interfaces with additional features. Decoding breaks up the 4 Gbytes of address space into 16 banks of 256 Mbytes. The banks 1 to 6 are directed to the EBI that associates these banks to the external chip selects NCS0 to NCS5. The bank 7 is directed to the DDRSDRC0 that associates this bank to DDR_NCS chip select and so dedicated to the 4-port DDR2/ LPDDR controller. The bank 0 is reserved for the addressing of the internal memories, and a second level of decoding provides 1 Mbyte of internal memory area. The bank 15 is reserved for the peripherals and provides access to the Advanced Peripheral Bus (APB). Other areas are unused and performing an access within them provides an abort to the master requesting such an access. 5.2 Embedded Memories 5.2.1 Internal SRAM The SAM9M11 product embeds a total of 64 Kbytes high-speed SRAM split in 4 blocks of 16 Kbytes connected to one slave of the matrix. After reset and until the Remap Command is performed, the four SRAM blocks are contiguous and only accessible at address 0x00300000. After Remap, the SRAM also becomes available at address 0x0. Figure 5-2. Internal SRAM Reset RAM RAM Remap 64K 64K 0x00300000 0x00000000 The SAM9M11 device embeds two memory features. The processor Tightly Coupled Memory Interface (TCM) that allows the processor to access the memory up to processor speed (PCK) and the interface on the AHB side allowing masters to access the memory at AHB speed (MCK). A wait state is necessary to access the TCM at 400 MHz. Setting the bit NWS_TCM in the bus Matrix TCM Configuration Register of the matrix inserts a wait state on the ITCM and DTCM accesses. 5.2.2 TCM Interface On the processor side, this Internal SRAM can be allocated to three areas:  Internal SRAM A is the ARM926EJ-S Instruction TCM. The user can map this SRAM block anywhere in the ARM926 instruction memory space using CP15 instructions and the TCR configuration register located in the Chip Configuration User Interface. This SRAM block is also accessible by the ARM926 Masters and by the AHB Masters through the AHB bus 18 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

 Internal SRAM B is the ARM926EJ-S Data TCM. The user can map this SRAM block anywhere in the ARM926 data memory space using CP15 instructions. This SRAM block is also accessible by the ARM926 Data Master and by the AHB Masters through the AHB bus.  Internal SRAM C is only accessible by all the AHB Masters. After reset and until the Remap Command is performed, this SRAM block is accessible through the AHB bus at address 0x0030 0000 by all the AHB Masters. After Remap, this SRAM block also becomes accessible through the AHB bus at address 0x0 by the ARM926 Instruction and the ARM926 Data Masters. Within the 64 Kbyte SRAM size available, the amount of memory assigned to each block is software programmable according to Table 5-1. Table 5-1. ITCM and DTCM Memory Configuration SRAM A ITCM size (Kbytes) seen at SRAM B DTCM size (Kbytes) seen at SRAM C (Kbytes) seenat 0x100000 through AHB 0x200000 through AHB 0x300000 through AHB 0 0 64 0 64 0 32 32 0 5.2.3 Internal ROM The SAM9M11 embeds an Internal ROM, which contains the boot ROM and SAM-BA® program. At any time, the ROM is mapped at address 0x0040 0000. It is also accessible at address 0x0 (BMS =1) after the reset and before the Remap Command. 5.3 I/O Drive Selection and Delay Control 5.3.1 I/O Drive Selection The aim of this control is to adapt the signal drive to the frequency. Two bits allow the user to select High or Low drive for memories data/address/ctrl signals.  Setting the bit [17], EBI_DRIVE, in the CCFG_EBICSA register of the matrix allows to control the drive of the EBI.  Setting the bit [18], DDR_DRIVE, in the CCFG_EBICSA register of the matrix allows to control the drive of the DDR. 5.3.2 Delay Control To avoid the simultaneous switching of all the I/Os, a delay can be inserted on the different EBI, DDR2 and PIO lines. The control of these delays is the following:  DDRSDRC DDR_D[15:0] controlled by two registers, DELAY1 and DELAY2, located in the DDRSDRC user interface ̶ DDR_D[0] <=> DELAY1[3:0], ̶ DDR_D[1] <=> DELAY1[7:4],... ̶ DDR_D[6] <=> DELAY1[27:24], ̶ DDR_D[7] <=> DELAY1[31:28] ̶ DDR_D[8] <=> DELAY2[3:0], ̶ DDR_D[9] <=> DELAY2[7:4],..., ̶ DDR_D[14] <=> DELAY2[27:24], ̶ DDR_D[15] <=> DELAY2[31:28] SAM9M11 [DATASHEET] 19 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

DDR_A[13:0] controlled by two registers, DELAY3 and DELAY4, located in the DDRSDRC user interface ̶ DDR_A[0] <=> DELAY3[3:0], ̶ DDR_A[1] <=> DELAY3[7:4], ..., ̶ DDR_A[6] <=> DELAY3[27:24], ̶ DDR_A[7] <=> DELAY3[31:28] ̶ DDR_A[8] <=> DELAY4[3:0], ̶ DDR_A[9] <=> DELAY4[7:4], ..., ̶ DDR_A[12] <=> DELAY4[19:16], ̶ DDR_A[13] <=> DELAY4[23:20]  EBI (DDRSDRC\HSMC3\Nandflash) D[15:0] controlled by two registers, DELAY1 and DELAY2, located in the HSMC3 user interface ̶ D[0] <=> DELAY1[3:0], ̶ D[1] <=> DELAY1[7:4],..., ̶ D[6] <=> DELAY1[27:24], ̶ D[7] <=> DELAY1[31:28] ̶ D[8] <=> DELAY2[3:0], ̶ D[9] <=> DELAY2[7:4],..., ̶ D[14] <=> DELAY2[27:24], ̶ D[15] <=> DELAY2[31:28] D[31,16]on PIOC[31:16] controlled by two registers, DELAY3 and DELAY4, located in the HSMC3 user interface ̶ D[16] <=> DELAY3[3:0], ̶ D[17] <=> DELAY3[7:4],..., ̶ D[22] <=> DELAY3[27:24], ̶ PC[23] <=> DELAY3[31:28] ̶ D[24] <=> DELAY4[3:0], ̶ D[25] <=> DELAY4[7:4],..., ̶ D[30] <=> DELAY4[27:24], ̶ D[31] <=> DELAY4[31:28] A[25:0], controlled by four registers, DELAY5, DELAY6, DELAY7and DELAY8, located in the HSMC3 user interface ̶ A[0] <=> DELAY5[3:0], ̶ A[1] <=> DELAY5[7:4],..., ̶ A[6] <=> DELAY5[27:24], ̶ A[7] <=> DELAY5[31:28] ̶ A[8] <=> DELAY6[3:0], ̶ A[9] <=> DELAY6[7:4],..., ̶ A[14] <=> DELAY6[27:24], ̶ A[15] <=> DELAY6[31:28] ̶ A[16] <=> DELAY7[3:0], ̶ A[17] <=> DELAY7[7:4], ̶ A[18] <=> DELAY7[11:8] 20 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

A25 on PC[12] and A[24:19] on PC[7:2] ̶ A19 <=> DELAY7[15:12], ̶ A20 <=> DELAY7[19:16],..., ̶ A23 <=> DELAY7[31:28], ̶ A24 <=> DELAY8[3:0], ̶ A25 <=> DELAY8[7:4]  PIOA User interface The delay can only be inserted on the HSMCI0 and HSMCI1 I/O lines, so on PA[9:2] and PA[30:23]. The delay is controlled by two registers, DELAY1 and DELAY2, located in the PIOA user interface. ̶ PA[2] <=> DELAY1[3:0], ̶ PA[3] <=> DELAY1[7:4],..., ̶ PA[8] <=> DELAY1[27:24], ̶ PA[9] <=> DELAY1[31:28] ̶ PA[23] <=> DELAY2[3:0], ̶ PA[24] <=> DELAY2[7:4],..., ̶ PA[29] <=> DELAY2[27:24], ̶ PA[30] <=> DELAY2[31:28] SAM9M11 [DATASHEET] 21 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

6. System Controller The System Controller is a set of peripherals that allows handling of key elements of the system, such as power, resets, clocks, time, interrupts, watchdog, etc. The System Controller User Interface also embeds the registers that configure the Matrix and a set of registers for the chip configuration. The chip configuration registers configure the EBI chip select assignment and voltage range for external memories. 6.1 System Controller Mapping The System Controller’s peripherals are all mapped within the highest 16 Kbytes of address space, between addresses 0xFFFF E200 and 0xFFFF FFFF. However, all the registers of the System Controller are mapped on the top of the address space. All the registers of the System Controller can be addressed from a single pointer by using the standard ARM instruction set, as the Load/Store instruction have an indexing mode of ±4 KB. Figure 6-1 on page 23 shows the System Controller block diagram. Figure 5.1 on page 18 shows the mapping of the User Interfaces of the System Controller peripherals. 22 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

6.2 System Controller Block Diagram Figure 6-1. SAM9M11 System Controller Block Diagram System Controller VDDCORE Powered irq0–irq2 nirq fiq Advanced nfiq Interrupt periph_irq[2..24] Controller pit_irq int rtt_irq wdt_irq ntrst dbgu_irq por_ntrst ARM926EJ-S pmc_irq rstc_irq periph_nrMeCseKt Debug dbgu_irq proc_nreset Unit dbgu_txd PCK dbgu_rxd debug MCK Periodic debug Interval pit_irq periph_nreset Timer SLCK jtag_nreset Boundary Scan debidulge WaTticmhedrog wdt_irq TAP Controller proc_nreset MCK wdt_fault WDRPROC periph_nreset Bus Matrix NRST rstc_irq VDDCORE pjtoarg__nntrrsetset periph_nreset POR Reset proc_nreset Controller backup_nreset VDDBU VDDBU Powered VDDBU UPLLCK POR SLCK UHP48M SLCK Real-time rtc_irq UHP12M backup_nreset Clock rtc_alarm USB High Speed SLCK Real-time rtt_irq periph_nreset Host Port backup_nreset Timer rtt_alarm periph_irq[25] SLCK SHDN WKUP Shutdown UPLLCK backup_nreset Controller RC rtt0_alarm USB High Speed Oscillator 4 General-purpose periph_nreset Device Port XIN32 Slow Clock Backup Registers periph_irq[24] Oscillator XOUT32 SCKCR SLCK periph_clk[2..30] int pck[0–1] XIN 12 MHz UHP48M MAINCK Main UHP12M XOUT Oscillator Power PCK MCK UPLL UPLLCK Management DDR sysclk Controller pmc_irq PLLA PLLACK idle periph_clk[6..30] periph_nreset periph_nreset periph_nreset periph_irq[2..6] Embedded periph_clk[2..6] irq Peripherals dbgu_rxd PIO fiq periph_irq[6..30] PA0–PA31 Controllers dbgu_txd PB0–PB31 in PC0–PC31 out enable PD0–PD31 PE0–PE31 SAM9M11 [DATASHEET] 23 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

6.3 Chip Identification The SAM9M11 Chip ID is defined in the Debug Unit Chip ID Register and Debug Unit Chip ID Extension Register.  Chip ID: 0x819B05A2  Ext ID: 0x00000001  JTAG ID: 05B2_703F  ARM926 TAP ID: 0x0792603F 6.4 Backup Section The SAM9M11 features a Backup Section that embeds:  RC Oscillator  Slow Clock Oscillator  Slow Clock Controller Configuration Register (SCKCR)  RTT  RTC  Shutdown Controller  128-bit backup registers  A part of RSTC This section is powered by the VDDBU rail. 24 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

7. Peripherals 7.1 Peripheral Mapping As shown in Figure 5.1 “Memory Mapping”, the peripherals are mapped in the upper 256 Mbytes of the address space between the addresses 0xFFF7 8000 and 0xFFFC FFFF. Each User Peripheral is allocated 16 Kbytes of address space. 7.2 Peripheral Identifiers Table 7-1 defines the Peripheral Identifiers of the SAM9M11. A peripheral identifier is required for the control of the peripheral interrupt with the Advanced Interrupt Controller and for the control of the peripheral clock with the Power Management Controlle. Table 7-1. SAM9M11 Peripheral Identifiers Peripheral ID Peripheral Mnemonic Peripheral Name External Interrupt 0 AIC Advanced Interrupt Controller FIQ 1 SYSC System Controller 2 PIOA Parallel I/O Controller A 3 PIOB Parallel I/O Controller B 4 PIOC Parallel I/O Controller C 5 PIOD, PIOE Parallel I/O Controller D, Parallel I/O Controller E 6 TRNG True Random Number Generator 7 US0 Universal Synchronous Asynchronous Receiver Transmitter 0 8 US1 Universal Synchronous Asynchronous Receiver Transmitter 1 9 US2 Universal Synchronous Asynchronous Receiver Transmitter 2 10 US3 Universal Synchronous Asynchronous Receiver Transmitter 3 11 MCI0 High Speed Multimedia Card Interface 0 12 TWI0 Two-wire Interface 0 13 TWI1 Two-wire Interface 1 14 SPI0 Serial Peripheral Interface 0 15 SPI1 Serial Peripheral Interface 1 16 SSC0 Synchronous Serial Controller 0 17 SSC1 Synchronous Serial Controller 1 18 TC0 .. TC5 Timer Counter 0 .. Timer Counter 5 19 PWM Pulse Width Modulation Controller 20 TSADCC Touchscreen ADC Controller 21 DMA DMA Controller 22 UHPHS USB High Speed Host Port 23 LCDC LCD Controller 24 AC97C AC97 Controller 25 EMAC Ethernet MAC SAM9M11 [DATASHEET] 25 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 7-1. SAM9M11 Peripheral Identifiers (Continued) Peripheral ID Peripheral Mnemonic Peripheral Name External Interrupt 26 ISI Image Sensor Interface 27 UDPHS USB High Speed Device Port Advanced Encryption Standard, Triple Data Encryption Standard, 28 AES, TDES, SHA Secure Hash Algorithm 29 MCI1 High Speed Multimedia Card Interface 1 30 VDEC Video Decoder 31 AIC Advanced Interrupt Controller IRQ 7.3 Peripheral Interrupts and Clock Control 7.3.1 System Interrupt The System Interrupt in Source 1 is the wired-OR of the interrupt signals coming from:  the DDR2/LPDDR Controller  the Debug Unit  the Periodic Interval Timer  the Real-time Timer  the Real-time Clock  the Watchdog Timer  the Reset Controller  the Power Management Controller The clock of these peripherals cannot be deactivated and Peripheral ID 1 can only be used within the Advanced Interrupt Controller. 7.3.2 External Interrupts All external interrupt signals, i.e., the Fast Interrupt signal FIQ or the Interrupt signal IRQ, use a dedicated Peripheral ID. However, there is no clock control associated with these peripheral IDs. 7.4 Peripheral Signals Multiplexing on I/O Lines The SAM9M11 features five PIO controllers, PIOA, PIOB, PIOC, PIOD and PIOE, which multiplex the I/O lines of the peripheral set. Each PIO Controller controls up to 32 lines. Each line can be assigned to one of two peripheral functions, A or B. The multiplexing tables in the following paragraphs define how the I/O lines of the peripherals A and B are multiplexed on the PIO Controllers. The two columns “Function” and “Comments” have been inserted in this table for the user’s own comments; they may be used to track how pins are defined in an application. Note that some peripheral function which are output only, might be duplicated within the both tables. The column “Reset State” indicates whether the PIO Line resets in I/O mode or in peripheral mode. If I/O is mentioned, the PIO Line resets in input with the pull-up enabled, so that the device is maintained in a static state as soon as the reset is released. As a result, the bit corresponding to the PIO Line in the register PIO_PSR (Peripheral Status Register) resets low. If a signal name is mentioned in the “Reset State” column, the PIO Line is assigned to this function and the corresponding bit in PIO_PSR resets high. This is the case of pins controlling memories, in particular the address lines, which require the pin to be driven as soon as the reset is released. Note that the pull-up resistor is also enabled in this case. 26 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

7.4.1 PIO Controller A Multiplexing Table 7-2. Multiplexing on PIO Controller A (PIOA) Reset Power I/O Line Peripheral A Peripheral B State Supply Function Comments PA0 MCI0_CK TCLK3 I/O VDDIOP0 PA1 MCI0_CDA TIOA3 I/O VDDIOP0 PA2 MCI0_DA0 TIOB3 I/O VDDIOP0 PA3 MCI0_DA1 TCKL4 I/O VDDIOP0 PA4 MCI0_DA2 TIOA4 I/O VDDIOP0 PA5 MCI0_DA3 TIOB4 I/O VDDIOP0 PA6 MCI0_DA4 ETX2 I/O VDDIOP0 PA7 MCI0_DA5 ETX3 I/O VDDIOP0 PA8 MCI0_DA6 ERX2 I/O VDDIOP0 PA9 MCI0_DA7 ERX3 I/O VDDIOP0 PA10 ETX0 I/O VDDIOP0 PA11 ETX1 I/O VDDIOP0 PA12 ERX0 I/O VDDIOP0 PA13 ERX1 I/O VDDIOP0 PA14 ETXEN I/O VDDIOP0 PA15 ERXDV I/O VDDIOP0 PA16 ERXER I/O VDDIOP0 PA17 ETXCK I/O VDDIOP0 PA18 EMDC I/O VDDIOP0 PA19 EMDIO I/O VDDIOP0 PA20 TWD0 I/O VDDIOP0 PA21 TWCK0 I/O VDDIOP0 PA22 MCI1_CDA SCK3 I/O VDDIOP0 PA23 MCI1_DA0 RTS3 I/O VDDIOP0 PA24 MCI1_DA1 CTS3 I/O VDDIOP0 PA25 MCI1_DA2 PWM3 I/O VDDIOP0 PA26 MCI1_DA3 TIOB2 I/O VDDIOP0 PA27 MCI1_DA4 ETXER I/O VDDIOP0 PA28 MCI1_DA5 ERXCK I/O VDDIOP0 PA29 MCI1_DA6 ECRS I/O VDDIOP0 PA30 MCI1_DA7 ECOL I/O VDDIOP0 PA31 MCI1_CK PCK0 I/O VDDIOP0 SAM9M11 [DATASHEET] 27 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

7.4.2 PIO Controller B Multiplexing Table 7-3. Multiplexing on PIO Controller B (PIOB) Reset Power I/O Line Peripheral A Peripheral B State Supply Function Comments PB0 SPI0_MISO I/O VDDIOP0 PB1 SPI0_MOSI I/O VDDIOP0 PB2 SPI0_SPCK I/O VDDIOP0 PB3 SPI0_NPCS0 I/O VDDIOP0 PB4 TXD1 I/O VDDIOP0 PB5 RXD1 I/O VDDIOP0 PB6 TXD2 I/O VDDIOP0 PB7 RXD2 I/O VDDIOP0 PB8 TXD3 ISI_D8 I/O VDDIOP2 PB9 RXD3 ISI_D9 I/O VDDIOP2 PB10 TWD1 ISI_D10 I/O VDDIOP2 PB11 TWCK1 ISI_D11 I/O VDDIOP2 PB12 DRXD I/O VDDIOP0 PB13 DTXD I/O VDDIOP0 PB14 SPI1_MISO I/O VDDIOP0 PB15 SPI1_MOSI CTS0 I/O VDDIOP0 PB16 SPI1_SPCK SCK0 I/O VDDIOP0 PB17 SPI1_NPCS0 RTS0 I/O VDDIOP0 PB18 RXD0 SPI0_NPCS1 I/O VDDIOP0 PB19 TXD0 SPI0_NPCS2 I/O VDDIOP0 PB20 ISI_D0 I/O VDDIOP2 PB21 ISI_D1 I/O VDDIOP2 PB22 ISI_D2 I/O VDDIOP2 PB23 ISI_D3 I/O VDDIOP2 PB24 ISI_D4 I/O VDDIOP2 PB25 ISI_D5 I/O VDDIOP2 PB26 ISI_D6 I/O VDDIOP2 PB27 ISI_D7 I/O VDDIOP2 PB28 ISI_PCK I/O VDDIOP2 PB29 ISI_VSYNC I/O VDDIOP2 PB30 ISI_HSYNC I/O VDDIOP2 PB31 ISI_MCK PCK1 I/O VDDIOP2 28 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

7.4.3 PIO Controller C Multiplexing Table 7-4. Multiplexing on PIO Controller C (PIOC) Reset Power I/O Line Peripheral A Peripheral B State Supply Function Comments PC0 DQM2 DQM2 VDDIOM1 PC1 DQM3 DQM3 VDDIOM1 PC2 A19 A19 VDDIOM1 PC3 A20 A20 VDDIOM1 PC4 A21/NANDALE A21 VDDIOM1 PC5 A22/NANDCLE A22 VDDIOM1 PC6 A23 A23 VDDIOM1 PC7 A24 A24 VDDIOM1 PC8 CFCE1 I/O VDDIOM1 PC9 CFCE2 RTS2 I/O VDDIOM1 PC10 NCS4/CFCS0 TCLK2 I/O VDDIOM1 PC11 NCS5/CFCS1 CTS2 I/O VDDIOM1 PC12 A25/CFRNW A25 VDDIOM1 PC13 NCS2 I/O VDDIOM1 PC14 NCS3/NANDCS I/O VDDIOM1 PC15 NWAIT I/O VDDIOM1 PC16 D16 I/O VDDIOM1 PC17 D17 I/O VDDIOM1 PC18 D18 I/O VDDIOM1 PC19 D19 I/O VDDIOM1 PC20 D20 I/O VDDIOM1 PC21 D21 I/O VDDIOM1 PC22 D22 I/O VDDIOM1 PC23 D23 I/O VDDIOM1 PC24 D24 I/O VDDIOM1 PC25 D25 I/O VDDIOM1 PC26 D26 I/O VDDIOM1 PC27 D27 I/O VDDIOM1 PC28 D28 I/O VDDIOM1 PC29 D29 I/O VDDIOM1 PC30 D30 I/O VDDIOM1 PC31 D31 I/O VDDIOM1 SAM9M11 [DATASHEET] 29 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

7.4.4 PIO Controller D Multiplexing Table 7-5. Multiplexing on PIO Controller D (PIOD) Reset Power I/O Line Peripheral A Peripheral B State Supply Function Comments PD0 TK0 PWM3 I/O VDDIOP0 PD1 TF0 I/O VDDIOP0 PD2 TD0 I/O VDDIOP0 PD3 RD0 I/O VDDIOP0 PD4 RK0 I/O VDDIOP0 PD5 RF0 I/O VDDIOP0 PD6 AC97RX I/O VDDIOP0 PD7 AC97TX TIOA5 I/O VDDIOP0 PD8 AC97FS TIOB5 I/O VDDIOP0 PD9 AC97CK TCLK5 I/O VDDIOP0 PD10 TD1 I/O VDDIOP0 PD11 RD1 I/O VDDIOP0 PD12 TK1 PCK0 I/O VDDIOP0 PD13 RK1 I/O VDDIOP0 PD14 TF1 I/O VDDIOP0 PD15 RF1 I/O VDDIOP0 PD16 RTS1 I/O VDDIOP0 PD17 CTS1 I/O VDDIOP0 PD18 SPI1_NPCS2 IRQ I/O VDDIOP0 PD19 SPI1_NPCS3 FIQ I/O VDDIOP0 PD20 TIOA0 I/O VDDANA TSAD0 PD21 TIOA1 I/O VDDANA TSAD1 PD22 TIOA2 I/O VDDANA TSAD2 PD23 TCLK0 I/O VDDANA TSAD3 PD24 SPI0_NPCS1 PWM0 I/O VDDANA GPAD4 PD25 SPI0_NPCS2 PWM1 I/O VDDANA GPAD5 PD26 PCK0 PWM2 I/O VDDANA GPAD6 PD27 PCK1 SPI0_NPCS3 I/O VDDANA GPAD7 PD28 TSADTRG SPI1_NPCS1 I/O VDDIOP0 PD29 TCLK1 SCK1 I/O VDDIOP0 PD30 TIOB0 SCK2 I/O VDDIOP0 PD31 TIOB1 PWM1 I/O VDDIOP0 30 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

7.4.5 PIO Controller E Multiplexing Table 7-6. Multiplexing on PIO Controller E (PIOE) Reset Power I/O Line Peripheral A Peripheral B State Supply Function Comments PE0 LCDPWR PCK0 I/O VDDIOP1 PE1 LCDMOD I/O VDDIOP1 PE2 LCDCC I/O VDDIOP1 PE3 LCDVSYNC I/O VDDIOP1 PE4 LCDHSYNC I/O VDDIOP1 PE5 LCDDOTCK I/O VDDIOP1 PE6 LCDDEN I/O VDDIOP1 PE7 LCDD0 LCDD2 I/O VDDIOP1 PE8 LCDD1 LCDD3 I/O VDDIOP1 PE9 LCDD2 LCDD4 I/O VDDIOP1 PE10 LCDD3 LCDD5 I/O VDDIOP1 PE11 LCDD4 LCDD6 I/O VDDIOP1 PE12 LCDD5 LCDD7 I/O VDDIOP1 PE13 LCDD6 LCDD10 I/O VDDIOP1 PE14 LCDD7 LCDD11 I/O VDDIOP1 PE15 LCDD8 LCDD12 I/O VDDIOP1 PE16 LCDD9 LCDD13 I/O VDDIOP1 PE17 LCDD10 LCDD14 I/O VDDIOP1 PE18 LCDD11 LCDD15 I/O VDDIOP1 PE19 LCDD12 LCDD18 I/O VDDIOP1 PE20 LCDD13 LCDD19 I/O VDDIOP1 PE21 LCDD14 LCDD20 I/O VDDIOP1 PE22 LCDD15 LCDD21 I/O VDDIOP1 PE23 LCDD16 LCDD22 I/O VDDIOP1 PE24 LCDD17 LCDD23 I/O VDDIOP1 PE25 LCDD18 I/O VDDIOP1 PE26 LCDD19 I/O VDDIOP1 PE27 LCDD20 I/O VDDIOP1 PE28 LCDD21 I/O VDDIOP1 PE29 LCDD22 I/O VDDIOP1 PE30 LCDD23 I/O VDDIOP1 PE31 PWM2 PCK1 I/O VDDIOP1 SAM9M11 [DATASHEET] 31 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

8. ARM926EJ-S Processor Overview 8.1 Description The ARM926EJ-S processor is a member of the ARM9™ family of general-purpose microprocessors. The ARM926EJ-S implements ARM architecture version 5TEJ and is targeted at multi-tasking applications where full memory management, high performance, low die size and low power are all important features. The ARM926EJ-S processor supports the 32-bit ARM and 16-bit THUMB instruction sets, enabling the user to trade off between high performance and high code density. It also supports 8-bit Java instruction set and includes features for efficient execution of Java bytecode, providing a Java performance similar to a JIT (Just-In-Time compilers), for the next generation of Java-powered wireless and embedded devices. It includes an enhanced multiplier design for improved DSP performance. The ARM926EJ-S processor supports the ARM debug architecture and includes logic to assist in both hardware and software debug. The ARM926EJ-S provides a complete high performance processor subsystem, including:  An ARM9EJ-S integer core  A Memory Management Unit (MMU)  Separate instruction and data AMBA AHB bus interfaces  Separate instruction and data TCM interfaces 32 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

8.2 Embedded Characteristics  RISC Processor Based on ARM v5TEJ Architecture with Jazelle technology for Java acceleration  Two Instruction Sets ̶ ARM High-performance 32-bit Instruction Set ̶ Thumb High Code Density 16-bit Instruction Set  DSP Instruction Extensions  5-Stage Pipeline Architecture: ̶ Instruction Fetch (F) ̶ Instruction Decode (D) ̶ Execute (E) ̶ Data Memory (M) ̶ Register Write (W)  32-Kbyte Data Cache, 32-Kbyte Instruction Cache ̶ Virtually-addressed 4-way Associative Cache ̶ Eight words per line ̶ Write-through and Write-back Operation ̶ Pseudo-random or Round-robin Replacement  Write Buffer ̶ Main Write Buffer with 16-word Data Buffer and 4-address Buffer ̶ DCache Write-back Buffer with 8-word Entries and a Single Address Entry ̶ Software Control Drain  Standard ARM v4 and v5 Memory Management Unit (MMU) ̶ Access Permission for Sections ̶ Access Permission for large pages and small pages can be specified separately for each quarter of the page ̶ 16 embedded domains  Bus Interface Unit (BIU) ̶ Arbitrates and Schedules AHB Requests ̶ Separate Masters for both instruction and data access providing complete Matrix system flexibility ̶ Separate Address and Data Buses for both the 32-bit instruction interface and the 32-bit data interface ̶ On Address and Data Buses, data can be 8-bit (Bytes), 16-bit (Half-words) or 32-bit (Words)  TCM Interface SAM9M11 [DATASHEET] 33 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

8.3 Block Diagram Figure 8-1. ARM926EJ-S Internal Functional Block Diagram External Coprocessors ETM9 CP15 System External Trace Port Configuration Coprocessor Interface Coprocessor Interface Write Data ARM9EJ-S Processor Core Instruction Read Fetches Data Data Instruction Address Address MMU Instruction DTCM Data TLB TLB ITCM Interface Interface Data TCM Instruction TCM Data Instruction Address Address AHB Interface Instruction Data Cache and Cache Write Buffer AMBA AHB 34 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

8.4 ARM9EJ-S Processor 8.4.1 ARM9EJ-S Operating States The ARM9EJ-S processor can operate in three different states, each with a specific instruction set:  ARM state: 32-bit, word-aligned ARM instructions.  THUMB state: 16-bit, halfword-aligned Thumb instructions.  Jazelle state: variable length, byte-aligned Jazelle instructions. In Jazelle state, all instruction Fetches are in words. 8.4.2 Switching State The operating state of the ARM9EJ-S core can be switched between:  ARM state and THUMB state using the BX and BLX instructions, and loads to the PC  ARM state and Jazelle state using the BXJ instruction All exceptions are entered, handled and exited in ARM state. If an exception occurs in Thumb or Jazelle states, the processor reverts to ARM state. The transition back to Thumb or Jazelle states occurs automatically on return from the exception handler. 8.4.3 Instruction Pipelines The ARM9EJ-S core uses two kinds of pipelines to increase the speed of the flow of instructions to the processor. A five-stage (five clock cycles) pipeline is used for ARM and Thumb states. It consists of Fetch, Decode, Execute, Memory and Writeback stages. A six-stage (six clock cycles) pipeline is used for Jazelle state It consists of Fetch, Jazelle/Decode (two clock cycles), Execute, Memory and Writeback stages. 8.4.4 Memory Access The ARM9EJ-S core supports byte (8-bit), half-word (16-bit) and word (32-bit) access. Words must be aligned to four-byte boundaries, half-words must be aligned to two-byte boundaries and bytes can be placed on any byte boundary. Because of the nature of the pipelines, it is possible for a value to be required for use before it has been placed in the register bank by the actions of an earlier instruction. The ARM9EJ-S control logic automatically detects these cases and stalls the core or forward data. 8.4.5 Jazelle Technology The Jazelle technology enables direct and efficient execution of Java byte codes on ARM processors, providing high performance for the next generation of Java-powered wireless and embedded devices. The new Java feature of ARM9EJ-S can be described as a hardware emulation of a JVM (Java Virtual Machine). Java mode will appear as another state: instead of executing ARM or Thumb instructions, it executes Java byte codes. The Java byte code decoder logic implemented in ARM9EJ-S decodes 95% of executed byte codes and turns them into ARM instructions without any overhead, while less frequently used byte codes are broken down into optimized sequences of ARM instructions. The hardware/software split is invisible to the programmer, invisible to the application and invisible to the operating system. All existing ARM registers are re-used in Jazelle state and all registers then have particular functions in this mode. Minimum interrupt latency is maintained across both ARM state and Java state. Since byte codes execution can be restarted, an interrupt automatically triggers the core to switch from Java state to ARM state for the execution of the interrupt handler. This means that no special provision has to be made for handling interrupts while executing byte codes, whether in hardware or in software. SAM9M11 [DATASHEET] 35 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

8.4.6 ARM9EJ-S Operating Modes In all states, there are seven operation modes:  User mode is the usual ARM program execution state. It is used for executing most application programs  Fast Interrupt (FIQ) mode is used for handling fast interrupts. It is suitable for high-speed data transfer or channel process  Interrupt (IRQ) mode is used for general-purpose interrupt handling  Supervisor mode is a protected mode for the operating system  Abort mode is entered after a data or instruction prefetch abort  System mode is a privileged user mode for the operating system  Undefined mode is entered when an undefined instruction exception occurs Mode changes may be made under software control, or may be brought about by external interrupts or exception processing. Most application programs execute in User Mode. The non-user modes, known as privileged modes, are entered in order to service interrupts or exceptions or to access protected resources. 8.4.7 ARM9EJ-S Registers The ARM9EJ-S core has a total of 37 registers.  31 general-purpose 32-bit registers  Six 32-bit status registers Table 8-1 shows all the registers in all modes. 36 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 8-1. ARM9EJ-S Modes and Registers Layout User and System Fast Interrupt Mode Supervisor Mode Abort Mode Undefined Mode Interrupt Mode Mode R0 R0 R0 R0 R0 R0 R1 R1 R1 R1 R1 R1 R2 R2 R2 R2 R2 R2 R3 R3 R3 R3 R3 R3 R4 R4 R4 R4 R4 R4 R5 R5 R5 R5 R5 R5 R6 R6 R6 R6 R6 R6 R7 R7 R7 R7 R7 R7 R8 R8 R8 R8 R8 R8_FIQ R9 R9 R9 R9 R9 R9_FIQ R10 R10 R10 R10 R10 R10_FIQ R11 R11 R11 R11 R11 R11_FIQ R12 R12 R12 R12 R12 R12_FIQ R13 R13_SVC R13_ABORT R13_UNDEF R13_IRQ R13_FIQ R14 R14_SVC R14_ABORT R14_UNDEF R14_IRQ R14_FIQ PC PC PC PC PC PC CPSR CPSR CPSR CPSR CPSR CPSR SPSR_SVC SPSR_ABORT SPSR_UNDEF SPSR_IRQ SPSR_FIQ Mode-specific banked registers The ARM state register set contains 16 directly-accessible registers, r0 to r15, and an additional register, the Current Program Status Register (CPSR). Registers r0 to r13 are general-purpose registers used to hold either data or address values. Register r14 is used as a Link register that holds a value (return address) of r15 when BL or BLX is executed. Register r15 is used as a program counter (PC), whereas the Current Program Status Register (CPSR) contains condition code flags and the current mode bits. In privileged modes (FIQ, Supervisor, Abort, IRQ, Undefined), mode-specific banked registers (r8 to r14 in FIQ mode or r13 to r14 in the other modes) become available. The corresponding banked registers r14_fiq, r14_svc, r14_abt, r14_irq, r14_und are similarly used to hold the values (return address for each mode) of r15 (PC) when interrupts and exceptions arise, or when BL or BLX instructions are executed within interrupt or exception routines. There is another register called Saved Program Status Register (SPSR) that becomes available in privileged modes instead of CPSR. This register contains condition code flags and the current mode bits saved as a result of the exception that caused entry to the current (privileged) mode. In all modes and due to a software agreement, register r13 is used as stack pointer. SAM9M11 [DATASHEET] 37 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The use and the function of all the registers described above should obey ARM Procedure Call Standard (APCS) which defines:  Constraints on the use of registers  Stack conventions  Argument passing and result return For more details, refer to ARM Software Development Kit. The Thumb state register set is a subset of the ARM state set. The programmer has direct access to:  Eight general-purpose registers r0–r7  Stack pointer, SP  Link register, LR (ARM r14)  PC  CPSR There are banked registers SPs, LRs and SPSRs for each privileged mode (for more details see the ARM9EJ-S Technical Reference Manual, revision r1p2 page 2-12). 8.4.7.1 Status Registers The ARM9EJ-S core contains one CPSR, and five SPSRs for exception handlers to use. The program status registers:  hold information about the most recently performed ALU operation  control the enabling and disabling of interrupts  set the processor operation mode Figure 8-2. Status Register Format 3130292827 24 7 6 5 0 N Z C V Q J Reserved I F T Mode Jazelle state bit Reserved Mode bits Sticky Overflow Overflow Thumb state bit Carry/Borrow/Extend Zero FIQ disable Negative/Less than IRQ disable Figure 8-2 shows the status register format, where:  N: Negative, Z: Zero, C: Carry, and V: Overflow are the four ALU flags  The Sticky Overflow (Q) flag can be set by certain multiply and fractional arithmetic instructions like QADD, QDADD, QSUB, QDSUB, SMLAxy, and SMLAWy needed to achieve DSP operations. The Q flag is sticky in that, when set by an instruction, it remains set until explicitly cleared by an MSR instruction writing to the CPSR. Instructions cannot execute conditionally on the status of the Q flag.  The J bit in the CPSR indicates when the ARM9EJ-S core is in Jazelle state, where: ̶ J = 0: The processor is in ARM or Thumb state, depending on the T bit ̶ J = 1: The processor is in Jazelle state.  Mode: five bits to encode the current processor mode 38 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

8.4.7.2 Exceptions 8.4.7.3 Exception Types and Priorities The ARM9EJ-S supports five types of exceptions. Each type drives the ARM9EJ-S in a privileged mode. The types of exceptions are:  Fast interrupt (FIQ)  Normal interrupt (IRQ)  Data and Prefetched aborts (Abort)  Undefined instruction (Undefined)  Software interrupt and Reset (Supervisor) When an exception occurs, the banked version of R14 and the SPSR for the exception mode are used to save the state. More than one exception can happen at a time, therefore the ARM9EJ-S takes the arisen exceptions according to the following priority order:  Reset (highest priority)  Data Abort  FIQ  IRQ  Prefetch Abort  BKPT, Undefined instruction, and Software Interrupt (SWI) (Lowest priority) The BKPT, or Undefined instruction, and SWI exceptions are mutually exclusive. Note that there is one exception in the priority scheme: when FIQs are enabled and a Data Abort occurs at the same time as an FIQ, the ARM9EJ-S core enters the Data Abort handler, and proceeds immediately to FIQ vector. A normal return from the FIQ causes the Data Abort handler to resume execution. Data Aborts must have higher priority than FIQs to ensure that the transfer error does not escape detection. 8.4.7.4 Exception Modes and Handling Exceptions arise whenever the normal flow of a program must be halted temporarily, for example, to service an interrupt from a peripheral. When handling an ARM exception, the ARM9EJ-S core performs the following operations: 1. Preserves the address of the next instruction in the appropriate Link Register that corresponds to the new mode that has been entered. When the exception entry is from: ̶ ARM and Jazelle states, the ARM9EJ-S copies the address of the next instruction into LR (current PC(r15) + 4 or PC + 8 depending on the exception). ̶ THUMB state, the ARM9EJ-S writes the value of the PC into LR, offset by a value (current PC + 2, PC + 4 or PC + 8 depending on the exception) that causes the program to resume from the correct place on return. 2. Copies the CPSR into the appropriate SPSR. 3. Forces the CPSR mode bits to a value that depends on the exception. 4. Forces the PC to fetch the next instruction from the relevant exception vector. The register r13 is also banked across exception modes to provide each exception handler with private stack pointer. The ARM9EJ-S can also set the interrupt disable flags to prevent otherwise unmanageable nesting of exceptions. When an exception has completed, the exception handler must move both the return value in the banked LR minus an offset to the PC and the SPSR to the CPSR. The offset value varies according to the type of exception. This action restores both PC and the CPSR. SAM9M11 [DATASHEET] 39 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The fast interrupt mode has seven private registers r8 to r14 (banked registers) to reduce or remove the requirement for register saving which minimizes the overhead of context switching. The Prefetch Abort is one of the aborts that indicates that the current memory access cannot be completed. When a Prefetch Abort occurs, the ARM9EJ-S marks the prefetched instruction as invalid, but does not take the exception until the instruction reaches the Execute stage in the pipeline. If the instruction is not executed, for example because a branch occurs while it is in the pipeline, the abort does not take place. The breakpoint (BKPT) instruction is a new feature of ARM9EJ-S that is destined to solve the problem of the Prefetch Abort. A breakpoint instruction operates as though the instruction caused a Prefetch Abort. A breakpoint instruction does not cause the ARM9EJ-S to take the Prefetch Abort exception until the instruction reaches the Execute stage of the pipeline. If the instruction is not executed, for example because a branch occurs while it is in the pipeline, the breakpoint does not take place. 40 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

8.4.8 ARM Instruction Set Overview The ARM instruction set is divided into:  Branch instructions  Data processing instructions  Status register transfer instructions  Load and Store instructions  Coprocessor instructions  Exception-generating instructions ARM instructions can be executed conditionally. Every instruction contains a 4-bit condition code field (bits[31:28]). For further details, see the ARM Technical Reference Manual. Table 8-2 gives the ARM instruction mnemonic list. Table 8-2. ARM Instruction Mnemonic List Mnemonic Operation Mnemonic Operation MOV Move MVN Move Not ADD Add ADC Add with Carry SUB Subtract SBC Subtract with Carry RSB Reverse Subtract RSC Reverse Subtract with Carry CMP Compare CMN Compare Negated TST Test TEQ Test Equivalence AND Logical AND BIC Bit Clear EOR Logical Exclusive OR ORR Logical (inclusive) OR MUL Multiply MLA Multiply Accumulate SMULL Sign Long Multiply UMULL Unsigned Long Multiply SMLAL Signed Long Multiply Accumulate UMLAL Unsigned Long Multiply Accumulate MSR Move to Status Register MRS Move From Status Register B Branch BL Branch and Link BX Branch and Exchange SWI Software Interrupt LDR Load Word STR Store Word LDRSH Load Signed Halfword LDRSB Load Signed Byte LDRH Load Half Word STRH Store Half Word LDRB Load Byte STRB Store Byte LDRBT Load Register Byte with Translation STRBT Store Register Byte with Translation LDRT Load Register with Translation STRT Store Register with Translation LDM Load Multiple STM Store Multiple SWP Swap Word SWPB Swap Byte MCR Move To Coprocessor MRC Move From Coprocessor LDC Load To Coprocessor STC Store From Coprocessor CDP Coprocessor Data Processing SAM9M11 [DATASHEET] 41 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

8.4.9 New ARM Instruction Set . Table 8-3. New ARM Instruction Mnemonic List Mnemonic Operation Mnemonic Operation BXJ Branch and exchange to Java MRRC Move double from coprocessor Alternative move of ARM reg to BLX (1) Branch, Link and exchange MCR2 coprocessor SMLAxy Signed Multiply Accumulate 16 * 16 bit MCRR Move double to coprocessor SMLAL Signed Multiply Accumulate Long CDP2 Alternative Coprocessor Data Processing SMLAWy Signed Multiply Accumulate 32 * 16 bit BKPT Breakpoint Soft Preload, Memory prepare to load from SMULxy Signed Multiply 16 * 16 bit PLD address SMULWy Signed Multiply 32 * 16 bit STRD Store Double QADD Saturated Add STC2 Alternative Store from Coprocessor QDADD Saturated Add with Double LDRD Load Double QSUB Saturated subtract LDC2 Alternative Load to Coprocessor QDSUB Saturated Subtract with double CLZ Count Leading Zeroes Notes: 1. A Thumb BLX contains two consecutive Thumb instructions, and takes four cycles. 42 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

8.4.10 Thumb Instruction Set Overview The Thumb instruction set is a re-encoded subset of the ARM instruction set. The Thumb instruction set is divided into:  Branch instructions  Data processing instructions  Load and Store instructions  Load and Store multiple instructions  Exception-generating instruction For further details, see the ARM Technical Reference Manual. Table 8-4 gives the Thumb instruction mnemonic list. Table 8-4. Thumb Instruction Mnemonic List Mnemonic Operation Mnemonic Operation MOV Move MVN Move Not ADD Add ADC Add with Carry SUB Subtract SBC Subtract with Carry CMP Compare CMN Compare Negated TST Test NEG Negate AND Logical AND BIC Bit Clear EOR Logical Exclusive OR ORR Logical (inclusive) OR LSL Logical Shift Left LSR Logical Shift Right ASR Arithmetic Shift Right ROR Rotate Right MUL Multiply BLX Branch, Link, and Exchange B Branch BL Branch and Link BX Branch and Exchange SWI Software Interrupt LDR Load Word STR Store Word LDRH Load Half Word STRH Store Half Word LDRB Load Byte STRB Store Byte LDRSH Load Signed Halfword LDRSB Load Signed Byte LDMIA Load Multiple STMIA Store Multiple PUSH Push Register to stack POP Pop Register from stack BCC Conditional Branch BKPT Breakpoint SAM9M11 [DATASHEET] 43 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

8.5 CP15 Coprocessor Coprocessor 15, or System Control Coprocessor CP15, is used to configure and control all the items in the list below:  ARM9EJ-S  Caches (ICache, DCache and write buffer)  TCM  MMU  Other system options To control these features, CP15 provides 16 additional registers. See Table 8-5. Table 8-5. CP15 Registers Register Name Read/Write 0 ID Code(1) Read/Unpredictable 0 Cache type(1) Read/Unpredictable 0 TCM status(1) Read/Unpredictable 1 Control Read/Write 2 Translation Table Base Read/Write 3 Domain Access Control Read/Write 4 Reserved None 5 Data fault Status(1) Read/Write 5 Instruction fault status(1) Read/Write 6 Fault Address Read/Write 7 Cache Operations Read/Write 8 TLB operations Unpredictable/Write 9 cache lockdown(2) Read/Write 9 TCM region Read/Write 10 TLB lockdown Read/Write 11 Reserved None 12 Reserved None 13 FCSE PID(1) Read/Write 13 Context ID(1) Read/Write 14 Reserved None 15 Test configuration Read/Write Notes: 1. Register locations 0,5, and 13 each provide access to more than one register. The register accessed depends on the value of the opcode_2 field. 2. Register location 9 provides access to more than one register. The register accessed depends on the value of the CRm field. 44 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

8.5.1 CP15 Registers Access CP15 registers can only be accessed in privileged mode by:  MCR (Move to Coprocessor from ARM Register) instruction is used to write an ARM register to CP15.  MRC (Move to ARM Register from Coprocessor) instruction is used to read the value of CP15 to an ARM register. Other instructions like CDP, LDC, STC can cause an undefined instruction exception. The assembler code for these instructions is: MCR/MRC{cond} p15, opcode_1, Rd, CRn, CRm, opcode_2. The MCR, MRC instructions bit pattern is shown below: 31 30 29 28 27 26 25 24 cond 1 1 1 0 23 22 21 20 19 18 17 16 opcode_1 L CRn 15 14 13 12 11 10 9 8 Rd 1 1 1 1 7 6 5 4 3 2 1 0 opcode_2 1 CRm • CRm[3:0]: Specified Coprocessor Action Determines specific coprocessor action. Its value is dependent on the CP15 register used. For details, refer to CP15 spe- cific register behavior. • opcode_2[7:5] Determines specific coprocessor operation code. By default, set to 0. • Rd[15:12]: ARM Register Defines the ARM register whose value is transferred to the coprocessor. If R15 is chosen, the result is unpredictable. • CRn[19:16]: Coprocessor Register Determines the destination coprocessor register. • L: Instruction Bit 0: MCR instruction 1: MRC instruction • opcode_1[23:20]: Coprocessor Code Defines the coprocessor specific code. Value is c15 for CP15. • cond [31:28]: Condition For more details, see Chapter 2 in ARM926EJ-S TRM. SAM9M11 [DATASHEET] 45 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

8.6 Memory Management Unit (MMU) The ARM926EJ-S processor implements an enhanced ARM architecture v5 MMU to provide virtual memory features required by operating systems like Symbian OS®, Windows CE®, and Linux®. These virtual memory features are memory access permission controls and virtual to physical address translations. The Virtual Address generated by the CPU core is converted to a Modified Virtual Address (MVA) by the FCSE (Fast Context Switch Extension) using the value in CP15 register13. The MMU translates modified virtual addresses to physical addresses by using a single, two-level page table set stored in physical memory. Each entry in the set contains the access permissions and the physical address that correspond to the virtual address. The first level translation tables contain 4096 entries indexed by bits [31:20] of the MVA. These entries contain a pointer to either a 1 MB section of physical memory along with attribute information (access permissions, domain, etc.) or an entry in the second level translation tables; coarse table and fine table. The second level translation tables contain two subtables, coarse table and fine table. An entry in the coarse table contains a pointer to both large pages and small pages along with access permissions. An entry in the fine table contains a pointer to large, small and tiny pages. Table 7 shows the different attributes of each page in the physical memory. Table 8-6. Mapping Details Mapping Name Mapping Size Access Permission By Subpage Size Section 1 Mbyte Section – Large Page 64 Kbytes 4 separated subpages 16 Kbytes Small Page 4 Kbytes 4 separated subpages 1 Kbyte Tiny Page 1 Kbyte Tiny Page – The MMU consists of:  Access control logic  Translation Look-aside Buffer (TLB)  Translation table walk hardware 8.6.1 Access Control Logic The access control logic controls access information for every entry in the translation table. The access control logic checks two pieces of access information: domain and access permissions. The domain is the primary access control mechanism for a memory region; there are 16 of them. It defines the conditions necessary for an access to proceed. The domain determines whether the access permissions are used to qualify the access or whether they should be ignored. The second access control mechanism is access permissions that are defined for sections and for large, small and tiny pages. Sections and tiny pages have a single set of access permissions whereas large and small pages can be associated with 4 sets of access permissions, one for each subpage (quarter of a page). 8.6.2 Translation Look-aside Buffer (TLB) The Translation Look-aside Buffer (TLB) caches translated entries and thus avoids going through the translation process every time. When the TLB contains an entry for the MVA (Modified Virtual Address), the access control logic determines if the access is permitted and outputs the appropriate physical address corresponding to the MVA. If access is not permitted, the MMU signals the CPU core to abort. If the TLB does not contain an entry for the MVA, the translation table walk hardware is invoked to retrieve the translation information from the translation table in physical memory. 46 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

8.6.3 Translation Table Walk Hardware The translation table walk hardware is a logic that traverses the translation tables located in physical memory, gets the physical address and access permissions and updates the TLB. The number of stages in the hardware table walking is one or two depending whether the address is marked as a section-mapped access or a page-mapped access. There are three sizes of page-mapped accesses and one size of section-mapped access. Page-mapped accesses are for large pages, small pages and tiny pages. The translation process always begins with a level one fetch. A section-mapped access requires only a level one fetch, but a page-mapped access requires an additional level two fetch. For further details on the MMU, please refer to chapter 3 in ARM926EJ-S Technical Reference Manual. 8.6.4 MMU Faults The MMU generates an abort on the following types of faults:  Alignment faults (for data accesses only)  Translation faults  Domain faults  Permission faults The access control mechanism of the MMU detects the conditions that produce these faults. If the fault is a result of memory access, the MMU aborts the access and signals the fault to the CPU core.The MMU retains status and address information about faults generated by the data accesses in the data fault status register and fault address register. It also retains the status of faults generated by instruction fetches in the instruction fault status register. The fault status register (register 5 in CP15) indicates the cause of a data or prefetch abort, and the domain number of the aborted access when it happens. The fault address register (register 6 in CP15) holds the MVA associated with the access that caused the Data Abort. For further details on MMU faults, please refer to chapter 3 in ARM926EJ-S Technical Reference Manual. SAM9M11 [DATASHEET] 47 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

8.7 Caches and Write Buffer The ARM926EJ-S contains a 32 Kbyte Instruction Cache (ICache), a 32 Kbyte Data Cache (DCache), and a write buffer. Although the ICache and DCache share common features, each still has some specific mechanisms. The caches (ICache and DCache) are four-way set associative, addressed, indexed and tagged using the Modified Virtual Address (MVA), with a cache line length of eight words with two dirty bits for the DCache. The ICache and DCache provide mechanisms for cache lockdown, cache pollution control, and line replacement. A new feature is now supported by ARM926EJ-S caches called allocate on read-miss commonly known as wrapping. This feature enables the caches to perform critical word first cache refilling. This means that when a request for a word causes a read-miss, the cache performs an AHB access. Instead of loading the whole line (eight words), the cache loads the critical word first, so the processor can reach it quickly, and then the remaining words, no matter where the word is located in the line. The caches and the write buffer are controlled by the CP15 register 1 (Control), CP15 register 7 (cache operations) and CP15 register 9 (cache lockdown). 8.7.1 Instruction Cache (ICache) The ICache caches fetched instructions to be executed by the processor. The ICache can be enabled by writing 1 to I bit of the CP15 Register 1 and disabled by writing 0 to this same bit. When the MMU is enabled, all instruction fetches are subject to translation and permission checks. If the MMU is disabled, all instructions fetches are cachable, no protection checks are made and the physical address is flat- mapped to the modified virtual address. With the MVA use disabled, context switching incurs ICache cleaning and/or invalidating. When the ICache is disabled, all instruction fetches appear on external memory (AHB) (see Tables 4-1 and 4-2 in page 4-4 in ARM926EJ-S TRM). On reset, the ICache entries are invalidated and the ICache is disabled. For best performance, ICache should be enabled as soon as possible after reset. 8.7.2 Data Cache (DCache) and Write Buffer ARM926EJ-S includes a DCache and a write buffer to reduce the effect of main memory bandwidth and latency on data access performance. The operations of DCache and write buffer are closely connected. 8.7.2.1 DCache The DCache needs the MMU to be enabled. All data accesses are subject to MMU permission and translation checks. Data accesses that are aborted by the MMU do not cause linefills or data accesses to appear on the AMBA ASB interface. If the MMU is disabled, all data accesses are noncachable, nonbufferable, with no protection checks, and appear on the AHB bus. All addresses are flat-mapped, VA = MVA = PA, which incurs DCache cleaning and/or invalidating every time a context switch occurs. The DCache stores the Physical Address Tag (PA Tag) from which every line was loaded and uses it when writing modified lines back to external memory. This means that the MMU is not involved in write-back operations. Each line (8 words) in the DCache has two dirty bits, one for the first four words and the other one for the second four words. These bits, if set, mark the associated half-lines as dirty. If the cache line is replaced due to a linefill or a cache clean operation, the dirty bits are used to decide whether all, half or none is written back to memory. DCache can be enabled or disabled by writing either 1 or 0 to bit C in register 1 of CP15 (see Tables 4-3 and 4-4 on page 4-5 in ARM926EJ-S TRM). The DCache supports write-through and write-back cache operations, selected by memory region using the C and B bits in the MMU translation tables. The DCache contains an eight data word entry, single address entry write-back buffer used to hold write-back data for cache line eviction or cleaning of dirty cache lines. 48 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The Write Buffer can hold up to 16 words of data and four separate addresses. DCache and Write Buffer operations are closely connected as their configuration is set in each section by the page descriptor in the MMU translation table. 8.7.2.2 Write Buffer The ARM926EJ-S contains a write buffer that has a 16-word data buffer and a four- address buffer. The write buffer is used for all writes to a bufferable region, write-through region and write-back region. It also allows to avoid stalling the processor when writes to external memory are performed. When a store occurs, data is written to the write buffer at core speed (high speed). The write buffer then completes the store to external memory at bus speed (typically slower than the core speed). During this time, the ARM9EJ-S processor can preform other tasks. DCache and Write Buffer support write-back and write-through memory regions, controlled by C and B bits in each section and page descriptor within the MMU translation tables. 8.7.2.3 Write-though Operation When a cache write hit occurs, the DCache line is updated. The updated data is then written to the write buffer which transfers it to external memory. When a cache write miss occurs, a line, chosen by round robin or another algorithm, is stored in the write buffer which transfers it to external memory. 8.7.2.4 Write-back Operation When a cache write hit occurs, the cache line or half line is marked as dirty, meaning that its contents are not up- to-date with those in the external memory. When a cache write miss occurs, a line, chosen by round robin or another algorithm, is stored in the write buffer which transfers it to external memory. SAM9M11 [DATASHEET] 49 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

8.8 Tightly-Coupled Memory Interface 8.8.1 TCM Description The ARM926EJ-S processor features a Tightly-coupled Memory (TCM) interface, which enables separate instruction and data TCMs (ITCM and DTCM) to be directly reached by the processor. TCMs are used to store real-time and performance critical code, they also provide a DMA support mechanism. Unlike AHB accesses to external memories, accesses to TCMs are fast and deterministic and do not incur bus penalties. The user has the possibility to independently configure each TCM size with values within the following ranges, [0Kbyte, 64 Kbytes] for ITCM size and [0 Kbyte, 64 Kbytes] for DTCM size. TCMs can be configured by two means: HMATRIX TCM register and TCM region register (register 9) in CP15 and both steps should be performed. HMATRIX TCM register sets TCM size whereas TCM region register (register 9) in CP15 maps TCMs and enables them. The data side of the ARM9EJ-S core is able to access the ITCM. This is necessary to enable code to be loaded into the ITCM, for SWI and emulated instruction handlers, and for accesses to PC-relative literal pools. 8.8.2 Enabling and Disabling TCMs Prior to any enabling step, the user should configure the TCM sizes in HMATRIX TCM register. Then enabling TCMs is performed by using TCM region register (register 9) in CP15. The user should use the same sizes as those put in HMATRIX TCM register. For further details and programming tips, please refer to chapter 2.3 in ARM926EJ-S TRM. 8.8.3 TCM Mapping The TCMs can be located anywhere in the memory map, with a single region available for ITCM and a separate region available for DTCM. The TCMs are physically addressed and can be placed anywhere in physical address space. However, the base address of a TCM must be aligned to its size, and the DTCM and ITCM regions must not overlap. TCM mapping is performed by using TCM region register (register 9) in CP15. The user should input the right mapping address for TCMs. 50 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

8.9 Bus Interface Unit The ARM926EJ-S features a Bus Interface Unit (BIU) that arbitrates and schedules AHB requests. The BIU implements a multi-layer AHB, based on the AHB-Lite protocol, that enables parallel access paths between multiple AHB masters and slaves in a system. This is achieved by using a more complex interconnection matrix and gives the benefit of increased overall bus bandwidth, and a more flexible system architecture. The multi-master bus architecture has a number of benefits:  It allows the development of multi-master systems with an increased bus bandwidth and a flexible architecture.  Each AHB layer becomes simple because it only has one master, so no arbitration or master-to-slave muxing is required. AHB layers, implementing AHB-Lite protocol, do not have to support request and grant, nor do they have to support retry and split transactions.  The arbitration becomes effective when more than one master wants to access the same slave simultaneously. 8.9.1 Supported Transfers The ARM926EJ-S processor performs all AHB accesses as single word, bursts of four words, or bursts of eight words. Any ARM9EJ-S core request that is not 1, 4, 8 words in size is split into packets of these sizes. Note that the Atmel bus is AHB-Lite protocol compliant, hence it does not support split and retry requests. Table 8-7 gives an overview of the supported transfers and different kinds of transactions they are used for. Table 8-7. Supported Transfers HBurst[2:0] Description Operation Single transfer of word, half word, or byte:  Data write (NCNB, NCB, WT, or WB that has missed in DCache) Single Single transfer  Data read (NCNB or NCB)  NC instruction fetch (prefetched and non-prefetched)  Page table walk read Half-line cache write-back, Instruction prefetch, if enabled. Four-word burst NCNB, Incr4 Four-word incrementing burst NCB, WT, or WB write. Incr8 Eight-word incrementing burst Full-line cache write-back, eight-word burst NCNB, NCB, WT, or WB write. Wrap8 Eight-word wrapping burst Cache linefill 8.9.2 Thumb Instruction Fetches All instructions fetches, regardless of the state of ARM9EJ-S core, are made as 32-bit accesses on the AHB. If the ARM9EJ-S is in Thumb state, then two instructions can be fetched at a time. 8.9.3 Address Alignment The ARM926EJ-S BIU performs address alignment checking and aligns AHB addresses to the necessary boundary. 16-bit accesses are aligned to halfword boundaries, and 32-bit accesses are aligned to word boundaries. SAM9M11 [DATASHEET] 51 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

9. SAM9M11 Debug and Test 9.1 Description The SAM9M11 features a number of complementary debug and test capabilities. A common JTAG/ICE (In-Circuit Emulator) port is used for standard debugging functions, such as downloading code and single-stepping through programs. The Debug Unit provides a two-pin UART that can be used to upload an application into internal SRAM. It manages the interrupt handling of the internal COMMTX and COMMRX signals that trace the activity of the Debug Communication Channel. A set of dedicated debug and test input/output pins gives direct access to these capabilities from a PC-based test environment. 9.2 Embedded Characteristics  ARM926 Real-time In-circuit Emulator ̶ Two real-time Watchpoint Units ̶ Two Independent Registers: Debug Control Register and Debug Status Register ̶ Test Access Port Accessible through JTAG Protocol ̶ Debug Communications Channel  Debug Unit ̶ Two-pin UART ̶ Debug Communication Channel Interrupt Handling ̶ Chip ID Register  IEEE® 1149.1 JTAG Boundary-scan on All Digital Pins 52 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

9.3 Block Diagram Figure 9-1. Debug and Test Block Diagram TMS TCK TDI NTRST ICE/JTAG JTAGSEL Boundary TAP Port TDO RTCK POR Reset and Test TST ARM9EJ-S ICE-RT ARM926EJ-S DTXD O PDC DBGU PI DRXD TAP: Test Access Port SAM9M11 [DATASHEET] 53 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

9.4 Application Examples 9.4.1 Debug Environment Figure 9-2 on page 54 shows a complete debug environment example. The ICE/JTAG interface is used for standard debugging functions, such as downloading code and single-stepping through the program. A software debugger running on a personal computer provides the user interface for configuring a Trace Port interface utilizing the ICE/JTAG interface. Figure 9-2. Application Debug and Trace Environment Example Host Debugger PC ICE/JTAG Interface ICE/JTAG Connector RS232 SAM9M11 Terminal Connector SAM9M11-based Application Board 54 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

9.4.2 Test Environment Figure 9-3 on page 55 shows a test environment example. Test vectors are sent and interpreted by the tester. In this example, the “board in test” is designed using a number of JTAG-compliant devices. These devices can be connected to form a single scan chain. Figure 9-3. Application Test Environment Example Test Adaptor Tester JTAG Interface ICE/JTAG Chip n Chip 2 SAM9M11 Chip 1 SAM9M11-based Application Board In Test 9.5 Debug and Test Pin Description Table 9-1. Debug and Test Pin List Pin Name Function Type Active Level Reset/Test NRST Microcontroller Reset Input/Output Low TST Test Mode Select Input High ICE and JTAG NTRST Test Reset Signal Input Low TCK Test Clock Input TDI Test Data In Input TDO Test Data Out Output TMS Test Mode Select Input RTCK Returned Test Clock Output JTAGSEL JTAG Selection Input Debug Unit DRXD Debug Receive Data Input DTXD Debug Transmit Data Output SAM9M11 [DATASHEET] 55 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

9.6 Functional Description 9.6.1 Test Pin One dedicated pin, TST, is used to define the device operating mode. The user must make sure that this pin is tied at low level to ensure normal operating conditions. Other values associated with this pin are reserved for manufacturing test. 9.6.2 EmbeddedICE The ARM9EJ-S EmbeddedICE-RT™ is supported via the ICE/JTAG port. It is connected to a host computer via an ICE interface. Debug support is implemented using an ARM9EJ-S core embedded within the ARM926EJ-S. The internal state of the ARM926EJ-S is examined through an ICE/JTAG port which allows instructions to be serially inserted into the pipeline of the core without using the external data bus. Therefore, when in debug state, a store- multiple (STM) can be inserted into the instruction pipeline. This exports the contents of the ARM9EJ-S registers. This data can be serially shifted out without affecting the rest of the system. There are two scan chains inside the ARM9EJ-S processor which support testing, debugging, and programming of the EmbeddedICE-RT. The scan chains are controlled by the ICE/JTAG port. EmbeddedICE mode is selected when JTAGSEL is low. It is not possible to switch directly between ICE and JTAG operations. A chip reset must be performed after JTAGSEL is changed. For further details on the EmbeddedICE-RT, see the ARM document: ARM9EJ-S Technical Reference Manual (DDI 0222A). 9.6.3 JTAG Signal Description TMS is the Test Mode Select input which controls the transitions of the test interface state machine. TDI is the Test Data Input line which supplies the data to the JTAG registers (Boundary Scan Register, Instruction Register, or other data registers). TDO is the Test Data Output line which is used to serially output the data from the JTAG registers to the equipment controlling the test. It carries the sampled values from the boundary scan chain (or other JTAG registers) and propagates them to the next chip in the serial test circuit. NTRST (optional in IEEE Standard 1149.1) is a Test-ReSeT input which is mandatory in ARM cores and used to reset the debug logic. On Atmel ARM926EJ-S-based cores, NTRST is a Power On Reset output. It is asserted on power on. If necessary, the user can also reset the debug logic with the NTRST pin assertion during 2.5 MCK periods. TCK is the Test ClocK input which enables the test interface. TCK is pulsed by the equipment controlling the test and not by the tested device. It can be pulsed at any frequency. Note the maximum JTAG clock rate on ARM926EJ-S cores is 1/6th the clock of the CPU. This gives 5.45 kHz maximum initial JTAG clock rate for an ARM9E running from the 32.768 kHz slow clock. RTCK is the Return Test Clock. Not an IEEE Standard 1149.1 signal added for a better clock handling by emulators. From some ICE Interface probes, this return signal can be used to synchronize the TCK clock and take not care about the given ratio between the ICE Interface clock and system clock equal to 1/6th. This signal is only available in JTAG ICE Mode and not in boundary scan mode. 9.6.4 Debug Unit The Debug Unit provides a two-pin (DXRD and TXRD) USART that can be used for several debug and trace purposes and offers an ideal means for in-situ programming solutions and debug monitor communication. Moreover, the association with two peripheral data controller channels permits packet handling of these tasks with processor time reduced to a minimum. 56 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The Debug Unit also manages the interrupt handling of the COMMTX and COMMRX signals that come from the ICE and that trace the activity of the Debug Communication Channel.The Debug Unit allows blockage of access to the system through the ICE interface. A specific register, the Debug Unit Chip ID Register, gives information about the product version and its internal configuration. The SAM9M11 Debug Unit Chip ID value is 0x819B 05A2 and the extended ID is 0x00000002 on 32-bit width. For further details on the Debug Unit, see the Debug Unit section. 9.6.5 IEEE 1149.1 JTAG Boundary Scan IEEE 1149.1 JTAG Boundary Scan allows pin-level access independent of the device packaging technology. IEEE 1149.1 JTAG Boundary Scan is enabled when JTAGSEL is high. The SAMPLE, EXTEST and BYPASS functions are implemented. In ICE debug mode, the ARM processor responds with a non-JTAG chip ID that identifies the processor to the ICE system. This is not IEEE 1149.1 JTAG-compliant. It is not possible to switch directly between JTAG and ICE operations. A chip reset must be performed after JTAGSEL is changed. A Boundary-scan Descriptor Language (BSDL) file is provided to set up test. SAM9M11 [DATASHEET] 57 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

9.6.6 JID Code Register Access: Read-only 31 30 29 28 27 26 25 24 VERSION PART NUMBER 23 22 21 20 19 18 17 16 PART NUMBER 15 14 13 12 11 10 9 8 PART NUMBER MANUFACTURER IDENTITY 7 6 5 4 3 2 1 0 MANUFACTURER IDENTITY 1 • VERSION[31:28]: Product Version Number Set to 0x0. • PART NUMBER[27:12]: Product Part Number Product part Number is 5B27 • MANUFACTURER IDENTITY[11:1] Set to 0x01F. Bit[0] required by IEEE Std. 1149.1. Set to 0x1. JTAG ID Code value is 05B2_703F. 58 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

10. Boot Strategies 10.1 Overview The system always boots at address 0x0. To ensure maximum boot possibilities the memory layout can be changed with two parameters.  REMAP allows the user to layout the internal SRAM bank to 0x0 to ease the development. This is done by software once the system has boot.  BMS allows the user to layout to 0x0, when convenient, the ROM or an external memory. This is done by hardware at reset. Note: All the memory blocks can always be seen at their specified base addresses that are not concerned by these parameters. The SAM9M11 manages a boot memory that depends on the level on the BMS pin at reset. For this reason, the internal memory area mapped between address 0x0 and 0x000F FFFF is reserved. If BMS is detected at 0, the boot memory is the memory connected on the Chip Select 0 of the External Bus Interface. In this case, the system state is the following:  on-chip RC as source clock  Static Memory Controller (SMC) in default configuration (byte select mode, 16-bit data bus, Read/Write controlled by Chip Select, allows boot on 16-bit non-volatile memory) To speed up the boot sequence user programmed software should perform a complete configuration:  Enable the 32768 Hz oscillator if best accuracy is needed  Program the PMC (main oscillator enable or bypass mode)  Program and start the PLL  Reprogram the SMC timings (using the registers SMC_SETUP, SMC_CYCLE, and SMC_MODE) for EBI CS0 to adapt them to the new clock  Switch the system clock to the new value If BMS is detected at 1, the boot memory is the embedded ROM and the boot program described below is executed. 10.2 Boot Program The boot program is contained in the embedded ROM. It is also called: “ROM Code” or “First level bootloader”. At power on, if the BMS pin is detected at 1, the boot memory is the embedded ROM and the boot program is executed. The Boot Program consists of several steps. First, it performs device initialization. Then it attempts to boot from external non-volatile memories (NVM). Finally, if no valid program is found in NVM, it executes a routine called “SAM-BA Monitor.” SAM9M11 [DATASHEET] 59 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

10.3 Flow Diagram The boot program implements the algorithm shown in Figure 10-1. Figure 10-1. Boot Program Algorithm Flow Diagram Device Setup Valid boot code Yes Copy and run it found in one in internal SRAM NVM No SAM-BA Monitor 60 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

10.4 Device Initialization 10.4.1 Clock at Startup At boot startup, the processor clock (PCK) and the master clock (MCK) are found on the slow clock. The slow clock can be an external 32 kHz crystal oscillator or the internal RC oscillator. By default the slow clock is the internal RC oscillator. Its frequency is not precise and is between 20 kHz and 40 kHz. Its startup is much faster than an external 32 kHz quartz. If a battery supplies the backup power and if the external 32 kHz clock was previously started up and selected, the slow clock at boot is the external 32 kHz quartz oscillator. Refer to the Slow Clock Crystal Oscillator description in Section 24. “Clock Generator”. 10.4.2 Initialization Sequence Initialization follows the steps described below: 1. Stack setup for ARM supervisor mode. 2. Main Oscillator Detection: (External crystal or external clock on XIN). The Main Oscillator is disabled at startup (MOSCEN = 0). First it is bypassed (OSCBYPASS set at 1). Then the MAINRDY bit is polled. Since this bit is raised, the Main Clock Frequency field is analyzed (MAINF). If the value is bigger than 16, an external clock connected on XIN is detected. If not, an external quartz connected between XIN and XOUT (whose frequency is unknown at this moment) is detected. 3. Main Oscillator Enabling: If an external clock is connected on XIN, the Main Oscillator does not need to be started. Otherwise, the OSCBYPASS bit is not set. The Main Oscillator is enabled (MOSCEN = 1) with the maximum startup time and the MOSC bit is polled to wait for stabilization. 4. Main Oscillator Selection: The Master Clock source is switched from Slow Clock to the Main Oscillator without prescaler. The PMC Status Register is polled to wait for MCK Ready. PCK and MCK are now the Main Oscillator clock. 5. C variable initialization: Non zero-initialized data are initialized in RAM (copy from ROM to RAM). Zero- initialized data are set to 0 in RAM. 6. PLLA initialization: PLLA is configured to allow communication on the USB link for the SAM-BA Monitor. Its configuration depends on the Main Oscillator source (external clock or crystal) and on its frequency. Table 10-1. External Clock and Crystal Frequencies allowed for Boot Sequence (in MHz) Description 4 12 28 Other Boot on External Memories Yes Yes Yes No SAM-BA Monitor through DBGU Yes Yes Yes No SAM-BA Monitor through USB No Yes No No SAM9M11 [DATASHEET] 61 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

10.5 NVM Boot 10.5.1 NVM Bootloader Program Description Figure 10-2. NVM Bootloader Program Diagram Start Initialize NVM No Restore the reset values Initialization OK ? for the peripherals and jump to next boot solution Yes Valid code detection in NVM No NVM contains valid code Yes Copy the valid code from external NVM to internal SRAM. Restore the reset values for the peripherals. Perform the REMAP and set the PC to 0 to jump to the downloaded application. End 62 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 10-3. Remap Action After Download Completion 0x0000_0000 0x0000_0000 REMAP Internal Internal ROM SRAM 0x0030_0000 0x0030_0000 Internal Internal SRAM SRAM 0x0040_0000 0x0040_0000 Internal Internal ROM ROM The NVM bootloader program initializes the NVM. It initializes the required PIO. It sets the right peripheral depending on the NVM and tries to access the memory. If the initialization fails, it restores the reset values for the PIO and peripherals and then the next NVM bootloader program is executed. If the initialization is successful, the NVM bootloader program reads the beginning of the NVM and determines if the NVM contains valid code. If the NVM does not contain valid code, the NVM bootloader program restores the reset value for the peripherals and then the next NVM bootloader program is executed. If valid code is found, this code is loaded from NVM into internal SRAM and executed by branching at address 0x0000_0000 after remap. This code may be the application code or a second-level bootloader. All the calls to functions are PC relative and do not use absolute addresses. SAM9M11 [DATASHEET] 63 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

10.5.2 Valid Code Detection There are two kinds of valid code detection. Depending on the NVM bootloader, either one or both of them is used. 10.5.2.1ARM Exception Vectors Check The NVM bootloader program reads and analyzes the first 28 bytes corresponding to the first seven ARM exception vectors. Except for the sixth vector, these bytes must implement the ARM instructions for either branch or load PC with PC relative addressing. Figure 10-4. LDR Opcode 31 28 27 24 23 20 19 16 15 12 11 0 1 1 1 0 0 1 I P U 1 W 0 Rn Rd O set Figure 10-5. B Opcode 31 28 27 24 23 0 1 1 1 0 1 0 1 0 O set (24 bits) Unconditional instruction: 0xE for bits 31 to 28 Load PC with PC relative addressing instruction: ̶ Rn = Rd = PC = 0xF ̶ I==0 (12-bit immediate value) ̶ P==1 (pre-indexed) ̶ U offset added (U==1) or subtracted (U==0) ̶ W==1 The sixth vector, at offset 0x14, contains the size of the image to download. The user must replace this vector with his/her own vector. This information is described below. Figure 10-6. Structure of the ARM Vector 6 31 0 Size of the code to download in bytes The value has to be smaller than 60 Kbytes. 60 Kbytes is the maximum size for a valid code. This size is the internal SRAM size minus the stack size used by the ROM Code at the end of the internal SRAM. Example An example of valid vectors follows: 00 ea000006 B0x20 04 eafffffe B0x04 08 ea00002f B_main 0c eafffffe B0x0c 10 eafffffe B0x10 14 00001234 Code size = 4660 bytes (< 60 Kbytes) 18 eafffffe B0x18 10.5.2.2boot.bin file check The NVM bootloader program looks for a boot.bin file in the root directory of a FAT12/16/32 formatted NVM Flash. 64 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

10.5.3 NVM Bootloader Sequence Figure 10-7. NVM Bootloader Sequence Diagram Device Setup Yes Copy from NAND Flash Boot Run NAND Flash Bootloader NAND Flash to SRAM No Yes Copy from SD Card Boot Run SD Card Bootloader SD Card to SRAM No Yes Copy from SPI Flash Boot Run SPI Flash Bootloader SPI Flash to SRAM No Yes Copy from TWI EEPROM Boot Run TWI EEPROM Bootloader TWI EEPROM to SRAM No SAM-BA Monitor 10.5.3.1NAND Flash Boot The NAND Flash bootloader program uses the EBI CS3. It uses both valid code detections. First it searches a boot.bin file. Then it analyzes the ARM exception vectors. The first block must be guaranteed by the manufacturer. There is no ECC check. After NAND Flash interface configuration, the Manufacturer ID is read. If it is different from 0xFF, the Device ID is read, else, the NAND Flash boot is aborted. The boot program contains a list of SLC small block Device IDs with their characteristics (size, bus width, voltage) (see Table 10-2). If the device ID is not found in this list, the NAND Flash device is considered as an SLC large block and its characteristics are obtained by reading the Extended Device ID byte 3. SAM9M11 [DATASHEET] 65 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Supported NAND Flash Devices The supported SLC small block NAND Flash devices are described in Table 10-2. Table 10-2. Supported SLC Small Block NAND Flash Devices Size PageSize Block Size Bus Width Voltage Device ID (Mbytes) (bytes) (bytes) (bits) (V) 0x6E 1 256 4096 8 5 0x64 2 256 4096 8 5 0x6B 4 512 8196 8 5 0xE8 1 256 4096 8 3.3 0xEC 1 256 4096 8 3.3 0xEA 2 256 4096 8 3.3 0xE3 4 512 8196 8 3.3 0xE5 4 512 8196 8 3.3 0xD6 8 512 8196 8 3.3 0xE6 8 512 8196 8 3.3 0x33 16 512 16384 8 1.8 0x73 16 512 16384 8 3.3 0x43 16 512 16384 16 1.8 0x53 16 512 16384 16 3.3 0x45 32 512 16384 16 1.8 0x55 32 512 16384 16 3.3 0x36 64 512 16384 8 1.8 0x76 64 512 16384 8 3.3 0x46 64 512 16384 16 1.8 0x56 64 512 16384 16 3.3 0x78 128 512 16384 8 1.8 0x79 128 512 16384 8 3.3 0x72 128 512 16384 16 1.8 0x74 128 512 16384 16 3.3 The NAND Flash boot also supports all the SLC large block NAND Flash devices. 10.5.3.2SD Card Boot The SD Card bootloader uses MCI0. It uses only one valid code detection. It searches a boot.bin file. Supported SD Card Devices SD Card Boot supports all SD Card memories compliant with SD Memory Card Specification V2.0. This includes SDHC cards. 66 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

10.5.3.3SPI Flash Boot Two kinds of SPI Flash are supported: SPI Serial Flash and SPI DataFlash. The SPI Flash bootloader tries to boot on SPI0 Chip Select 0, first looking for SPI Serial Flash, and then for SPI DataFlash. It uses only one valid code detection: analysis of ARM exception vectors. The SPI Flash read is done using the Continuous Read command from address 0x0. This command is 0xE8 for DataFlash and 0x0B for Serial Flash devices. Supported DataFlash Devices The SPI Flash Boot program supports the DataFlash devices listed in Table 10-3. Table 10-3. DataFlash Devices Device Density Page Size (bytes) Number of Pages AT45DB011 1 Mbit 264 512 AT45DB021 2 Mbits 264 1024 AT45DB041 4 Mbits 264 2048 AT45DB081 8 Mbits 264 4096 AT45DB161 16 Mbits 528 4096 AT45DB321 32 Mbits 528 8192 AT45DB642 64 Mbits 1056 8192 Supported Serial Flash Devices The SPI Flash Boot program supports all Serial Flash devices. 10.5.3.4TWI EEPROM Boot The TWI EEPROM Bootloader uses the TWI0. It uses only one valid code detection. It analyzes the ARM exception vectors. Supported TWI EEPROM Devices TWI EEPROM Boot supports all I2C-compatible TWI EEPROM memories using 7 bits device address 0x50. 10.5.4 Hardware and Software Constraints The NVM drivers use several PIOs in peripheral mode to communicate with devices. Care must be taken when these PIOs are used by the application. The devices connected could be unintentionally driven at boot time, and electrical conflicts between output pins used by the NVM drivers and the connected devices may occur. To assure correct functionality, it is recommended to plug in critical devices to other pins not used by NVM. Table 10-4 on page 68 contains a list of pins that are driven during the boot program execution. These pins are driven during the boot sequence for a period of less than 1 second if no correct boot program is found. Before performing the jump to the application in internal SRAM, all the PIOs and peripherals used in the boot program are set to their reset state. SAM9M11 [DATASHEET] 67 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 10-4. PIO Driven During Boot Program Execution NVM Bootloader Peripheral Pin PIO Line EBI CS3 SMC NANDCS PIOC14 EBI CS3 SMC NAND ALE A21 NAND EBI CS3 SMC NAND CLE A22 EBI CS3 SMC Cmd/Addr/Data D[16:0] MCI0 MCI0_CK PIOA0 MCI0 MCI0_CD PIOA1 MCI0 MCI0_D0 PIOA2 SD Card MCI0 MCI0_D1 PIOA3 MCI0 MCI0_D2 PIOA4 MCI0 MCI0_D3 PIOA5 SPI0 MOSI PIOB1 SPI0 MISO PIOB0 SPI Flash SPI0 SPCK PIOB2 SPI0 NPCS0 PIOB3 TWI0 TWD0 PIOA20 TWI0 EEPROM TWI0 TWCK0 PIOA21 DBGU DRXD PIOB12 SAM-BA Monitor DBGU DTXD PIOB13 68 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

10.6 SAM-BA Monitor If no valid code has been found in NVM during the NVM bootloader sequence, the SAM-BA Monitor program is launched. The SAM-BA Monitor steps are: 1. Initialize DBGU and USB 2. Check if USB Device enumeration occurred or if characters are received on the DBGU Once the communication interface is identified, the application runs in an infinite loop waiting for different commands as listed in Table 10-5 on page 70. Figure 10-8. SAM-BA Monitor Diagram No valid code in NVM Init DBGU and USB No No USB Enumeration Character(s) received Successful ? on DBGU ? Yes Yes Run monitor Run monitor Wait for command Wait for command on the USB link on the DBGU link SAM9M11 [DATASHEET] 69 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

10.6.1 Command List Table 10-5. Commands Available through the SAM-BA Monitor Command Action Argument(s) Example N Set Normal mode No argument N# T Set Terminal mode No argument T# O Write a byte Address, Value# O200001,CA# o Read a byte Address,# o200001,# H Write a half word Address, Value# H200002,CAFE# h Read a half word Address,# h200002,# W Write a word Address, Value# W200000,CAFEDECA# w Read a word Address,# w200000,# S Send a file Address,# S200000,# R Receive a file Address, NbOfBytes# R200000,1234# G Go Address# G200200# V Display version No argument V#  Mode commands: ̶ Normal mode configures SAM-BA Monitor to send / receive data in binary format, ̶ Terminal mode configures SAM-BA Monitor to send / receive data in ascii format.  Write commands: Write a byte (O), a halfword (H) or a word (W) to the target. ̶ Address: Address in hexadecimal. ̶ Value: Byte, halfword or word to write in hexadecimal. ̶ Output: ‘>’.  Read commands: Read a byte (o), a halfword (h) or a word (w) from the target. ̶ Address: Address in hexadecimal ̶ Output: The byte, halfword or word read in hexadecimal following by ‘>’  Send a file (S): Send a file to a specified address ̶ Address: Address in hexadecimal ̶ Output: ‘>’. Note: There is a time-out on this command which is reached when the prompt ‘>’ appears before the end of the command execution.  Receive a file (R): Receive data into a file from a specified address ̶ Address: Address in hexadecimal ̶ NbOfBytes: Number of bytes in hexadecimal to receive ̶ Output: ‘>’  Go (G): Jump to a specified address and execute the code ̶ Address: Address to jump in hexadecimal ̶ Output: ‘>’once returned from the program execution. If the executed program does not handle the link register at its entry and does not return, the prompt will not be displayed.  Get Version (V): Return the Boot Program version ̶ Output: version, date and time of ROM code followed by the prompt: ‘>’. 70 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

10.6.2 DBGU Serial Port Communication is performed through the DBGU serial port initialized to 115200 baud, 8 bits of data, no parity, 1 stop bit. 10.6.2.1Supported External Crystal/External Clocks The SAM-BA Monitor supports a frequency of 12 MHz to allow DBGU communication for both external crystal and external clock. 10.6.2.2Xmodem Protocol The Send and Receive File commands use the Xmodem protocol to communicate. Any terminal performing this protocol can be used to send the application file to the target. The size of the binary file to send depends on the SRAM size embedded in the product. In all cases, the size of the binary file must be lower than the SRAM size because the Xmodem protocol requires some SRAM memory in order to work. The Xmodem protocol supported is the 128-byte length block. This protocol uses a two-character CRC-16 to guarantee detection of a maximum bit error. Xmodem protocol with CRC is accurate provided both sender and receiver report successful transmission. Each block of the transfer looks like: <SOH><blk #><255-blk #><--128 data bytes--><checksum> in which: ̶ <SOH> = 01 hex ̶ <blk #> = binary number, starts at 01, increments by 1, and wraps 0FFH to 00H (not to 01) ̶ <255-blk #> = 1’s complement of the blk#. ̶ <checksum> = 2 bytes CRC16 Figure 10-9 shows a transmission using this protocol. Figure 10-9. Xmodem Transfer Example Host Device C SOH 01 FE Data[128] CRC CRC ACK SOH 02 FD Data[128] CRC CRC ACK SOH 03 FC Data[100] CRC CRC ACK EOT ACK SAM9M11 [DATASHEET] 71 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

10.6.3 USB Device Port 10.6.3.1Supported External Crystal/External Clocks The only frequency supported by SAM-BA Monitor to allow USB communication is a 12 MHz crystal or external clock. 10.6.3.2USB Class The device uses the USB communication device class (CDC) drivers to take advantage of the installed PC RS-232 software to talk over the USB. The CDC class is implemented in all releases of Windows® beginning with Windows 98SE®. The CDC document, available at www.usb.org, describes how to implement devices such as ISDN modems and virtual COM ports. The Vendor ID is Atmel’s vendor ID 0x03EB. The product ID is 0x6124. These references are used by the host operating system to mount the correct driver. On Windows systems, the INF files contain the correspondence between vendor ID and product ID. 10.6.3.3Enumeration Process The USB protocol is a master/slave protocol. The host starts the enumeration, sending requests to the device through the control endpoint. The device handles standard requests as defined in the USB Specification. Table 10-6. Handled Standard Requests Request Definition GET_DESCRIPTOR Returns the current device configuration value SET_ADDRESS Sets the device address for all future device access SET_CONFIGURATION Sets the device configuration GET_CONFIGURATION Returns the current device configuration value GET_STATUS Returns status for the specified recipient SET_FEATURE Used to set or enable a specific feature CLEAR_FEATURE Used to clear or disable a specific feature The device also handles some class requests defined in the CDC class. Table 10-7. Handled Class Requests Request Definition SET_LINE_CODING Configures DTE rate, stop bits, parity and number of character bits GET_LINE_CODING Requests current DTE rate, stop bits, parity and number of character bits SET_CONTROL_LINE_STATE RS-232 signal used to tell the DCE device the DTE device is now present Unhandled requests are STALLed. 10.6.3.4Communication Endpoints There are two communication endpoints and endpoint 0 is used for the enumeration process. Endpoint 1 is a 64- byte Bulk OUT endpoint and endpoint 2 is a 64-byte Bulk IN endpoint. SAM-BA Boot commands are sent by the host through endpoint 1. If required, the message is split by the host into several data payloads by the host driver. If the command requires a response, the host can send IN transactions to pick up the response. 72 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

11. Reset Controller (RSTC) 11.1 Description The Reset Controller (RSTC), based on power-on reset cells, handles all the resets of the system without any external components. It reports which reset occurred last. The Reset Controller also drives independently or simultaneously the external reset and the peripheral and processor resets. 11.2 Embedded Characteristics The Reset Controller is based on two Power-on-Reset cells, one on VDDBU and one on VDDCORE. The Reset Controller is capable to return to the software the source of the last reset, either a general reset (VDDBU rising), a wake-up reset (VDDCORE rising), a software reset, a user reset or a watchdog reset. The Reset Controller controls the internal resets of the system and the NRST pin. The NRST pin is bidirectional. It is handled by the on-chip reset controller and can be driven low to provide a reset signal to the external components or asserted low externally to reset the microcontroller. It will reset the Core and the peripherals except the Backup region. There is no constraint on the length of the reset pulse and the reset controller can guarantee a minimum pulse length. The NRST pin integrates a permanent pull-up resistor to VDDIOP0 of about 100 kΩ. NRST is an open drain output. The configuration of the Reset Controller is saved as supplied on VDDBU. 11.3 Block Diagram Figure 11-1. Reset Controller Block Diagram Reset Controller Main Supply POR rstc_irq Backup Supply Startup POR Counter Reset State Manager proc_nreset user_reset NRST NRST periph_nreset Manager nrst_out exter_nreset backup_neset WDRPROC wd_fault SLCK SAM9M11 [DATASHEET] 73 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

11.4 Functional Description 11.4.1 Reset Controller Overview The Reset Controller is made up of an NRST Manager, a Startup Counter and a Reset State Manager. It runs at Slow Clock and generates the following reset signals:  proc_nreset: Processor reset line. It also resets the Watchdog Timer.  backup_nreset: Affects all the peripherals powered by VDDBU.  periph_nreset: Affects the whole set of embedded peripherals.  nrst_out: Drives the NRST pin. These reset signals are asserted by the Reset Controller, either on external events or on software action. The Reset State Manager controls the generation of reset signals and provides a signal to the NRST Manager when an assertion of the NRST pin is required. The NRST Manager shapes the NRST assertion during a programmable time, thus controlling external device resets. The startup counter waits for the complete crystal oscillator startup. The wait delay is given by the crystal oscillator startup time maximum value that can be found in the section Crystal Oscillator Characteristics in the Electrical Characteristics section of the product datasheet. The Reset Controller Mode Register (RSTC_MR), allowing the configuration of the Reset Controller, is powered with VDDBU, so that its configuration is saved as long as VDDBU is on. 11.4.2 NRST Manager The NRST Manager samples the NRST input pin and drives this pin low when required by the Reset State Manager. Figure 11-2 shows the block diagram of the NRST Manager. Figure 11-2. NRST Manager RSTC_MR URSTIEN RSTC_SR URSTS rstc_irq NRSTL RSTC_MR Other interrupt URSTEN sources user_reset NRST RSTC_MR ERSTL nrst_out External Reset Timer exter_nreset 11.4.2.1NRST Signal or Interrupt The NRST Manager samples the NRST pin at Slow Clock speed. When the line is detected low, a User Reset is reported to the Reset State Manager. However, the NRST Manager can be programmed to not trigger a reset when an assertion of NRST occurs. Writing the bit URSTEN at 0 in RSTC_MR disables the User Reset trigger. The level of the pin NRST can be read at any time in the bit NRSTL (NRST level) in RSTC_SR. As soon as the pin NRST is asserted, the bit URSTS in RSTC_SR is set. This bit clears only when RSTC_SR is read. The Reset Controller can also be programmed to generate an interrupt instead of generating a reset. To do so, the bit URSTIEN in RSTC_MR must be written at 1. 74 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

11.4.2.2NRST External Reset Control The Reset State Manager asserts the signal ext_nreset to assert the NRST pin. When this occurs, the “nrst_out” signal is driven low by the NRST Manager for a time programmed by the field ERSTL in RSTC_MR. This assertion duration, named EXTERNAL_RESET_LENGTH, lasts 2(ERSTL+1) Slow Clock cycles. This gives the approximate duration of an assertion between 60 µs and 2 seconds. Note that ERSTL at 0 defines a two-cycle duration for the NRST pulse. This feature allows the Reset Controller to shape the NRST pin level, and thus to guarantee that the NRST line is driven low for a time compliant with potential external devices connected on the system reset. As the field is within RSTC_MR, which is backed up, this field can be used to shape the system power-up reset for devices requiring a longer startup time than the Slow Clock Oscillator. 11.4.3 BMS Sampling The product matrix manages a boot memory that depends on the level on the BMS pin at reset. The BMS signal is sampled three slow clock cycles after the Core Power-On-Reset output rising edge. Figure 11-3. BMS Sampling SLCK Core Supply POR output XXX H or L BMS Signal BMS sampling delay = 3 cycles proc_nreset 11.4.4 Reset States The Reset State Manager handles the different reset sources and generates the internal reset signals. It reports the reset status in the field RSTTYP of the Status Register (RSTC_SR). The update of the field RSTTYP is performed when the processor reset is released. SAM9M11 [DATASHEET] 75 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

11.4.4.1General Reset A general reset occurs when VDDBU and VDDCORE are powered on. The backup supply POR cell output rises and is filtered with a Startup Counter, which operates at Slow Clock. The purpose of this counter is to make sure the Slow Clock oscillator is stable before starting up the device. The length of startup time is hardcoded to comply with the Slow Clock Oscillator startup time. After this time, the processor clock is released at Slow Clock and all the other signals remain valid for three cycles for proper processor and logic reset. Then, all the reset signals are released and the field RSTTYP in RSTC_SR reports a General Reset. As the RSTC_MR is reset, the NRST line rises 2 cycles after the backup_nreset, as ERSTL defaults at value 0x0. When VDDBU is detected low by the Backup Supply POR Cell, all resets signals are immediately asserted, even if the Main Supply POR Cell does not report a Main Supply shutdown. VDDBU only activates the backup_nreset signal. The backup_nreset must be released so that any other reset can be generated by VDDCORE (Main Supply POR output). Figure 11-4 shows how the General Reset affects the reset signals. Figure 11-4. General Reset State SLCK MCK Any Freq. Backup Supply POR output Startup Time Main Supply POR output backup_nreset Processor Startup = 3 cycles proc_nreset RSTTYP XXX 0x0 = General Reset XXX periph_nreset NRST (nrst_out) BMS Sampling EXTERNAL RESET LENGTH = 2 cycles 76 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

11.4.4.2Wake-up Reset The Wake-up Reset occurs when the Main Supply is down. When the Main Supply POR output is active, all the reset signals are asserted except backup_nreset. When the Main Supply powers up, the POR output is resynchronized on Slow Clock. The processor clock is then re-enabled during three Slow Clock cycles, depending on the requirements of the ARM processor. At the end of this delay, the processor and other reset signals rise. The field RSTTYP in RSTC_SR is updated to report a Wake-up Reset. The “nrst_out” remains asserted for EXTERNAL_RESET_LENGTH cycles. As RSTC_MR is backed up, the programmed number of cycles is applicable. When the Main Supply is detected falling, the reset signals are immediately asserted. This transition is synchronous with the output of the Main Supply POR. Figure 11-5. Wake-up State SLCK MCK Any Freq. Main Supply POR output backup_nreset Resynch. Processor Startup 2 cycles = 3 cycles proc_nreset RSTTYP XXX 0x1 = WakeUp Reset XXX periph_nreset NRST (nrst_out) EXTERNAL RESET LENGTH = 4 cycles (ERSTL = 1) SAM9M11 [DATASHEET] 77 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

11.4.4.3User Reset The User Reset is entered when a low level is detected on the NRST pin and the bit URSTEN in RSTC_MR is at 1. The NRST input signal is resynchronized with SLCK to insure proper behavior of the system. The User Reset is entered as soon as a low level is detected on NRST. The Processor Reset and the Peripheral Reset are asserted. The User Reset is left when NRST rises, after a two-cycle resynchronization time and a three-cycle processor startup. The processor clock is re-enabled as soon as NRST is confirmed high. When the processor reset signal is released, the RSTTYP field of the Status Register (RSTC_SR) is loaded with the value 0x4, indicating a User Reset. The NRST Manager guarantees that the NRST line is asserted for EXTERNAL_RESET_LENGTH Slow Clock cycles, as programmed in the field ERSTL. However, if NRST does not rise after EXTERNAL_RESET_LENGTH because it is driven low externally, the internal reset lines remain asserted until NRST actually rises. Figure 11-6. User Reset State SLCK MCK Any Freq. NRST Resynch. Resynch. Processor Startup 2 cycles 2 cycles = 3 cycles proc_nreset RSTTYP Any XXX 0x4 = User Reset periph_nreset NRST (nrst_out) >= EXTERNAL RESET LENGTH 78 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

11.4.4.4Software Reset The Reset Controller offers several commands used to assert the different reset signals. These commands are performed by writing the Control Register (RSTC_CR) with the following bits at1:  PROCRST: Writing PROCRST at 1 resets the processor and the watchdog timer.  PERRST: Writing PERRST at 1 resets all the embedded peripherals, including the memory system, and, in particular, the Remap Command. The Peripheral Reset is generally used for debug purposes. Except for Debug purposes, PERRST must always be used in conjunction with PROCRST (PERRST and PROCRST set both at 1 simultaneously.)  EXTRST: Writing EXTRST at 1 asserts low the NRST pin during a time defined by the field ERSTL in the Mode Register (RSTC_MR). The software reset is entered if at least one of these bits is set by the software. All these commands can be performed independently or simultaneously. The software reset lasts three Slow Clock cycles. The internal reset signals are asserted as soon as the register write is performed. This is detected on the Master Clock (MCK). They are released when the software reset is left, i.e., synchronously to SLCK. If EXTRST is set, the nrst_out signal is asserted depending on the programming of the field ERSTL. However, the resulting falling edge on NRST does not lead to a User Reset. If and only if the PROCRST bit is set, the Reset Controller reports the software status in the field RSTTYP of the Status Register (RSTC_SR). Other Software Resets are not reported in RSTTYP. As soon as a software operation is detected, the bit SRCMP (Software Reset Command in Progress) is set in the Status Register (RSTC_SR). It is cleared as soon as the software reset is left. No other software reset can be performed while the SRCMP bit is set, and writing any value in RSTC_CR has no effect. Figure 11-7. Software Reset SLCK MCK Any Freq. Write RSTC_CR Resynch. Processor Startup 1 cycle = 3 cycles proc_nreset if PROCRST=1 RSTTYP Any XXX 0x3 = Software Reset periph_nreset if PERRST=1 NRST (nrst_out) if EXTRST=1 EXTERNAL RESET LENGTH 8 cycles (ERSTL=2) SRCMP in RSTC_SR SAM9M11 [DATASHEET] 79 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

11.4.4.5Watchdog Reset The Watchdog Reset is entered when a watchdog fault occurs. This state lasts three Slow Clock cycles. When in Watchdog Reset, assertion of the reset signals depends on the WDRPROC bit in WDT_MR:  If WDRPROC is 0, the Processor Reset and the Peripheral Reset are asserted. The NRST line is also asserted, depending on the programming of the field ERSTL. However, the resulting low level on NRST does not result in a User Reset state.  If WDRPROC = 1, only the processor reset is asserted. The Watchdog Timer is reset by the proc_nreset signal. As the watchdog fault always causes a processor reset if WDRSTEN is set, the Watchdog Timer is always reset after a Watchdog Reset, and the Watchdog is enabled by default and with a period set to a maximum. When the WDRSTEN in WDT_MR bit is reset, the watchdog fault has no impact on the reset controller. Figure 11-8. Watchdog Reset SLCK MCK Any Freq. wd_fault Processor Startup = 3 cycles proc_nreset RSTTYP Any XXX 0x2 = Watchdog Reset periph_nreset Only if WDRPROC = 0 NRST (nrst_out) EXTERNAL RESET LENGTH 8 cycles (ERSTL=2) 80 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

11.4.5 Reset State Priorities The Reset State Manager manages the following priorities between the different reset sources, given in descending order:  Backup Reset  Wake-up Reset  Watchdog Reset  Software Reset  User Reset Particular cases are listed below:  When in User Reset: ̶ A watchdog event is impossible because the Watchdog Timer is being reset by the proc_nreset signal. ̶ A software reset is impossible, since the processor reset is being activated.  When in Software Reset: ̶ A watchdog event has priority over the current state. ̶ The NRST has no effect.  When in Watchdog Reset: ̶ The processor reset is active and so a Software Reset cannot be programmed. ̶ A User Reset cannot be entered. SAM9M11 [DATASHEET] 81 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

11.4.6 Reset Controller Status Register The Reset Controller status register (RSTC_SR) provides several status fields:  RSTTYP field: This field gives the type of the last reset, as explained in previous sections.  SRCMP bit: This field indicates that a Software Reset Command is in progress and that no further software reset should be performed until the end of the current one. This bit is automatically cleared at the end of the current software reset.  NRSTL bit: The NRSTL bit of the Status Register gives the level of the NRST pin sampled on each MCK rising edge.  URSTS bit: A high-to-low transition of the NRST pin sets the URSTS bit of the RSTC_SR. This transition is also detected on the Master Clock (MCK) rising edge (see Figure 11-9). If the User Reset is disabled (URSTEN = 0) and if the interruption is enabled by the URSTIEN bit in the RSTC_MR, the URSTS bit triggers an interrupt. Reading the RSTC_SR status register resets the URSTS bit and clears the interrupt. Figure 11-9. Reset Controller Status and Interrupt MCK read Peripheral Access RSTC_SR 2 cycle 2 cycle resynchronization resynchronization NRST NRSTL URSTS rstc_irq if (URSTEN = 0) and (URSTIEN = 1) 82 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

11.5 Reset Controller (RSTC) User Interface Table 11-1. Register Mapping Offset Register Name Access Reset Backup Reset 0x00 Control Register RSTC_CR Write-only – – 0x04 Status Register RSTC_SR Read-only 0x0000_0001 0x0000_0000 0x08 Mode Register RSTC_MR Read/Write – 0x0000_0001 Note: 1. The reset value of RSTC_SR either reports a General Reset or a Wake-up Reset depending on last rising power supply. SAM9M11 [DATASHEET] 83 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

11.5.1 Reset Controller Control Register Name: RSTC_CR Address: 0xFFFFFD00 Access: Write-only 31 30 29 28 27 26 25 24 KEY 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – 7 6 5 4 3 2 1 0 – – – – EXTRST PERRST – PROCRST • PROCRST: Processor Reset 0: No effect. 1: If KEY is correct, resets the processor. • PERRST: Peripheral Reset 0: No effect. 1: If KEY is correct, resets the peripherals. • EXTRST: External Reset 0: No effect. 1: If KEY is correct, asserts the NRST pin. • KEY: Password Should be written at value 0xA5. Writing any other value in this field aborts the write operation. 84 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

11.5.2 Reset Controller Status Register Name: RSTC_SR Address: 0xFFFFFD04 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – SRCMP NRSTL 15 14 13 12 11 10 9 8 – – – – – RSTTYP 7 6 5 4 3 2 1 0 – – – – – – – URSTS • URSTS: User Reset Status 0: No high-to-low edge on NRST happened since the last read of RSTC_SR. 1: At least one high-to-low transition of NRST has been detected since the last read of RSTC_SR. • RSTTYP: Reset Type Reports the cause of the last processor reset. Reading this RSTC_SR does not reset this field. RSTTYP Reset Type Comments 0 0 0 General Reset Both VDDCORE and VDDBU rising 0 0 1 Wake Up Reset VDDCORE rising 0 1 0 Watchdog Reset Watchdog fault occurred 0 1 1 Software Reset Processor reset required by the software 1 0 0 User Reset NRST pin detected low • NRSTL: NRST Pin Level Registers the NRST Pin Level at Master Clock (MCK). • SRCMP: Software Reset Command in Progress 0: No software command is being performed by the reset controller. The reset controller is ready for a software command. 1: A software reset command is being performed by the reset controller. The reset controller is busy. SAM9M11 [DATASHEET] 85 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

11.5.3 Reset Controller Mode Register Name: RSTC_MR Address: 0xFFFFFD08 Access: Read/Write 31 30 29 28 27 26 25 24 KEY 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – ERSTL 7 6 5 4 3 2 1 0 – – URSTIEN – – – URSTEN • URSTEN: User Reset Enable 0: The detection of a low level on the pin NRST does not generate a User Reset. 1: The detection of a low level on the pin NRST triggers a User Reset. • URSTIEN: User Reset Interrupt Enable 0: USRTS bit in RSTC_SR at 1 has no effect on rstc_irq. 1: USRTS bit in RSTC_SR at 1 asserts rstc_irq if URSTEN = 0. • ERSTL: External Reset Length This field defines the external reset length. The external reset is asserted during a time of 2(ERSTL+1) Slow Clock cycles. This allows assertion duration to be programmed between 60 µs and 2 seconds. • KEY: Password Should be written at value 0xA5. Writing any other value in this field aborts the write operation. 86 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

12. Real-time Timer (RTT) 12.1 Description The Real-time Timer (RTT) is built around a 32-bit counter and used to count elapsed seconds. It generates a periodic interrupt and/or triggers an alarm on a programmed value. 12.2 Embedded Characteristics  Real-time Timer, allowing backup of time with different accuracies ̶ 32-bit Free-running back-up Counter ̶ Integrates a 16-bit programmable prescaler running on slow clock ̶ Alarm Register capable to generate a wake-up of the system through the Shutdown Controller 12.3 Block Diagram Figure 12-1. Real-time Timer RTT_MR RTT_MR RTTRST RTPRES RTT_MR reload RTTINCIEN SLCK 16-bit Divider 0 set RTT_MR RTT_SR RTTINC RTTRST 1 0 reset rtt_int 32-bit Counter read RTT_MR RTT_SR ALMIEN reset RTT_VR CRTV RTT_SR ALMS set rtt_alarm = RTT_AR ALMV 12.4 Functional Description The Real-time Timer is used to count elapsed seconds. It is built around a 32-bit counter fed by Slow Clock divided by a programmable 16-bit value. The value can be programmed in the field RTPRES of the Real-time Mode Register (RTT_MR). Programming RTPRES at 0x00008000 corresponds to feeding the real-time counter with a 1 Hz signal (if the Slow Clock is 32.768 kHz). The 32-bit counter can count up to 232 seconds, corresponding to more than 136 years, then roll over to 0. SAM9M11 [DATASHEET] 87 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The Real-time Timer can also be used as a free-running timer with a lower time-base. The best accuracy is achieved by writing RTPRES to 3. Programming RTPRES to 1 or 2 is possible, but may result in losing status events because the status register is cleared two Slow Clock cycles after read. Thus if the RTT is configured to trigger an interrupt, the interrupt occurs during 2 Slow Clock cycles after reading RTT_SR. To prevent several executions of the interrupt handler, the interrupt must be disabled in the interrupt handler and re-enabled when the status register is clear. The Real-time Timer value (CRTV) can be read at any time in the register RTT_VR (Real-time Value Register). As this value can be updated asynchronously from the Master Clock, it is advisable to read this register twice at the same value to improve accuracy of the returned value. The current value of the counter is compared with the value written in the alarm register RTT_AR (Real-time Alarm Register). If the counter value matches the alarm, the bit ALMS in RTT_SR is set. The alarm register is set to its maximum value, corresponding to 0xFFFF_FFFF, after a reset. The bit RTTINC in RTT_SR is set each time the Real-time Timer counter is incremented. This bit can be used to start a periodic interrupt, the period being one second when the RTPRES is programmed with 0x8000 and Slow Clock equal to 32.768 Hz. Reading the RTT_SR status register resets the RTTINC and ALMS fields. Writing the bit RTTRST in RTT_MR immediately reloads and restarts the clock divider with the new programmed value. This also resets the 32-bit counter. Note: Because of the asynchronism between the Slow Clock (SCLK) and the System Clock (MCK): 1) The restart of the counter and the reset of the RTT_VR current value register is effective only 2 slow clock cycles after the write of the RTTRST bit in the RTT_MR. 2) The status register flags reset is taken into account only 2 slow clock cycles after the read of the RTT_SR (Status Register). Figure 12-2. RTT Counting APB cycle APB cycle SCLK RTPRES - 1 Prescaler 0 RTT 0 ... ALMV-1 ALMV ALMV+1 ALMV+2 ALMV+3 RTTINC (RTT_SR) ALMS (RTT_SR) APB Interface read RTT_SR 88 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

12.5 Real-time Timer (RTT) User Interface Table 12-1. Register Mapping Offset Register Name Access Reset 0x00 Mode Register RTT_MR Read/Write 0x0000_8000 0x04 Alarm Register RTT_AR Read/Write 0xFFFF_FFFF 0x08 Value Register RTT_VR Read-only 0x0000_0000 0x0C Status Register RTT_SR Read-only 0x0000_0000 SAM9M11 [DATASHEET] 89 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

12.5.1 Real-time Timer Mode Register Name: RTT_MR Address: 0xFFFFFD20 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – RTTRST RTTINCIEN ALMIEN 15 14 13 12 11 10 9 8 RTPRES 7 6 5 4 3 2 1 0 RTPRES • RTPRES: Real-time Timer Prescaler Value Defines the number of SLCK periods required to increment the Real-time timer. RTPRES is defined as follows: RTPRES = 0: The prescaler period is equal to 216. RTPRES ≠ 0: The prescaler period is equal to RTPRES. • ALMIEN: Alarm Interrupt Enable 0: The bit ALMS in RTT_SR has no effect on interrupt. 1: The bit ALMS in RTT_SR asserts interrupt. • RTTINCIEN: Real-time Timer Increment Interrupt Enable 0: The bit RTTINC in RTT_SR has no effect on interrupt. 1: The bit RTTINC in RTT_SR asserts interrupt. • RTTRST: Real-time Timer Restart 1: Reloads and restarts the clock divider with the new programmed value. This also resets the 32-bit counter. 90 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

12.5.2 Real-time Timer Alarm Register Name: RTT_AR Address: 0xFFFFFD24 Access: Read/Write 31 30 29 28 27 26 25 24 ALMV 23 22 21 20 19 18 17 16 ALMV 15 14 13 12 11 10 9 8 ALMV 7 6 5 4 3 2 1 0 ALMV • ALMV: Alarm Value Defines the alarm value (ALMV+1) compared with the Real-time Timer. SAM9M11 [DATASHEET] 91 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

12.5.3 Real-time Timer Value Register Name: RTT_VR Address: 0xFFFFFD28 Access: Read-only 31 30 29 28 27 26 25 24 CRTV 23 22 21 20 19 18 17 16 CRTV 15 14 13 12 11 10 9 8 CRTV 7 6 5 4 3 2 1 0 CRTV • CRTV: Current Real-time Value Returns the current value of the Real-time Timer. 92 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

12.5.4 Real-time Timer Status Register Name: RTT_SR Address: 0xFFFFFD2C Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – RTTINC ALMS • ALMS: Real-time Alarm Status 0: The Real-time Alarm has not occurred since the last read of RTT_SR. 1: The Real-time Alarm occurred since the last read of RTT_SR. • RTTINC: Real-time Timer Increment 0: The Real-time Timer has not been incremented since the last read of the RTT_SR. 1: The Real-time Timer has been incremented since the last read of the RTT_SR. SAM9M11 [DATASHEET] 93 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

13. Real-time Clock (RTC) 13.1 Description The Real-time Clock (RTC) peripheral is designed for very low power consumption. It combines a complete time-of-day clock with alarm and a two-hundred-year Gregorian calendar, complemented by a programmable periodic interrupt. The alarm and calendar registers are accessed by a 32-bit data bus. The time and calendar values are coded in binary-coded decimal (BCD) format. The time format can be 24-hour mode or 12-hour mode with an AM/PM indicator. Updating time and calendar fields and configuring the alarm fields are performed by a parallel capture on the 32-bit data bus. An entry control is performed to avoid loading registers with incompatible BCD format data or with an incompatible date according to the current month/year/century. 13.2 Embedded Characteristics  Low power consumption  Full asynchronous design  Two hundred year calendar  Programmable Periodic Interrupt  Alarm and update parallel load 13.3 Block Diagram Figure 13-1. RTC Block Diagram Crystal Oscillator: SLCK 32768 Divider Time Date Bus Interface Bus Interface Entry Interrupt RTC Interrupt Control Control 94 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

13.4 Product Dependencies 13.4.1 Power Management The Real-time Clock is continuously clocked at 32768 Hz. The Power Management Controller has no effect on RTC behavior. 13.4.2 Interrupt The RTC Interrupt is connected to interrupt source 1 (IRQ1) of the advanced interrupt controller. This interrupt line is due to the OR-wiring of the system peripheral interrupt lines (System Timer, Real-time Clock, Power Management Controller, Memory Controller, etc.). When a system interrupt occurs, the service routine must first determine the cause of the interrupt. This is done by reading the status registers of the above system peripherals successively. 13.5 Functional Description The RTC provides a full binary-coded decimal (BCD) clock that includes century (19/20), year (with leap years), month, date, day, hours, minutes and seconds. The valid year range is 1900 to 2099, a two-hundred-year Gregorian calendar achieving full Y2K compliance. The RTC can operate in 24-hour mode or in 12-hour mode with an AM/PM indicator. Corrections for leap years are included (all years divisible by 4 being leap years, including year 2000). This is correct up to the year 2099. After a general reset (a backup reset), the calendar is initialized to Thursday, January 1, 1998. 13.5.1 Reference Clock The reference clock is Slow Clock (SLCK). It can be driven internally or by an external 32.768 kHz crystal. During low power modes of the processor (idle mode), the oscillator runs and power consumption is critical. The crystal selection has to take into account the current consumption for power saving and the frequency drift due to temperature effect on the circuit for time accuracy. 13.5.2 Timing The RTC is updated in real time at one-second intervals in normal mode for the counters of seconds, at one- minute intervals for the counter of minutes and so on. Due to the asynchronous operation of the RTC with respect to the rest of the chip, to be certain that the value read in the RTC registers (century, year, month, date, day, hours, minutes, seconds) are valid and stable, it is necessary to read these registers twice. If the data is the same both times, then it is valid. Therefore, a minimum of two and a maximum of three accesses are required. 13.5.3 Alarm The RTC has five programmable fields: month, date, hours, minutes and seconds. Each of these fields can be enabled or disabled to match the alarm condition:  If all the fields are enabled, an alarm flag is generated (the corresponding flag is asserted and an interrupt generated if enabled) at a given month, date, hour/minute/second.  If only the “seconds” field is enabled, then an alarm is generated every minute. Depending on the combination of fields enabled, a large number of possibilities are available to the user ranging from minutes to 365/366 days. SAM9M11 [DATASHEET] 95 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

13.5.4 Error Checking Verification on user interface data is performed when accessing the century, year, month, date, day, hours, minutes, seconds and alarms. A check is performed on illegal BCD entries such as illegal date of the month with regard to the year and century configured. If one of the time fields is not correct, the data is not loaded into the register/counter and a flag is set in the validity register. The user can not reset this flag. It is reset as soon as an acceptable value is programmed. This avoids any further side effects in the hardware. The same procedure is done for the alarm. The following checks are performed: 1. Century (check if it is in range 19–20) 2. Year (BCD entry check) 3. Date (check range 01–31) 4. Month (check if it is in BCD range 01–12, check validity regarding “date”) 5. Day (check range 1–7) 6. Hour (BCD checks: in 24-hour mode, check range 00–23 and check that AM/PM flag is not set if RTC is set in 24-hour mode; in 12-hour mode check range 01–12) 7. Minute (check BCD and range 00–59) 8. Second (check BCD and range 00–59) Note: If the 12-hour mode is selected by means of the RTC_MODE register, a 12-hour value can be programmed and the returned value on RTC_TIME will be the corresponding 24-hour value. The entry control checks the value of the AM/PM indicator (bit 22 of RTC_TIME register) to determine the range to be checked. 13.5.5 Updating Time/Calendar To update any of the time/calendar fields, the user must first stop the RTC by setting the corresponding field in the Control Register. Bit UPDTIM must be set to update time fields (hour, minute, second) and bit UPDCAL must be set to update calendar fields (century, year, month, date, day). Then the user must poll or wait for the interrupt (if enabled) of bit ACKUPD in the Status Register. Once the bit reads 1, it is mandatory to clear this flag by writing the corresponding bit in RTC_SCCR. The user can now write to the appropriate Time and Calendar register. Once the update is finished, the user must reset (0) UPDTIM and/or UPDCAL in the Control When entering programming mode of the calendar fields, the time fields remain enabled. When entering the programming mode of the time fields, both time and calendar fields are stopped. This is due to the location of the calendar logic circuity (downstream for low-power considerations). It is highly recommended to prepare all the fields to be updated before entering programming mode. In successive update operations, the user must wait at least one second after resetting the UPDTIM/UPDCAL bit in the RTC_CR (Control Register) before setting these bits again. This is done by waiting for the SEC flag in the Status Register before setting UPDTIM/UPDCAL bit. After resetting UPDTIM/UPDCAL, the SEC flag must also be cleared. 96 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 13-2. Update Sequence Begin Prepare TIme or Calendar Fields Set UPDTIM and/or UPDCAL bit(s) in RTC_CR Read RTC_SR Polling or IRQ (if enabled) No ACKUPD = 1 ? Yes Clear ACKUPD bit in RTC_SCCR Update Time andor Calendar values in RTC_TIMR/RTC_CALR Clear UPDTIM and/or UPDCAL bit in RTC_CR End SAM9M11 [DATASHEET] 97 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

13.6 Real-time Clock (RTC) User Interface Table 13-1. Register Mapping Offset Register Name Access Reset 0x00 Control Register RTC_CR Read/Write 0x0 0x04 Mode Register RTC_MR Read/Write 0x0 0x08 Time Register RTC_TIMR Read/Write 0x0 0x0C Calendar Register RTC_CALR Read/Write 0x01210720 0x10 Time Alarm Register RTC_TIMALR Read/Write 0x0 0x14 Calendar Alarm Register RTC_CALALR Read/Write 0x01010000 0x18 Status Register RTC_SR Read-only 0x0 0x1C Status Clear Command Register RTC_SCCR Write-only --- 0x20 Interrupt Enable Register RTC_IER Write-only --- 0x24 Interrupt Disable Register RTC_IDR Write-only --- 0x28 Interrupt Mask Register RTC_IMR Read-only 0x0 0x2C Valid Entry Register RTC_VER Read-only 0x0 0xFC Reserved – – – 98 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

13.6.1 RTC Control Register Name: RTC_CR Address: 0xFFFFFDB0 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – CALEVSEL 15 14 13 12 11 10 9 8 – – – – – – TIMEVSEL 7 6 5 4 3 2 1 0 – – – – – – UPDCAL UPDTIM • UPDTIM: Update Request Time Register 0: No effect. 1: Stops the RTC time counting. Time counting consists of second, minute and hour counters. Time counters can be programmed once this bit is set and acknowledged by the bit ACKUPD of the Status Register. • UPDCAL: Update Request Calendar Register 0: No effect. 1: Stops the RTC calendar counting. Calendar counting consists of day, date, month, year and century counters. Calendar counters can be programmed once this bit is set. • TIMEVSEL: Time Event Selection The event that generates the flag TIMEV in RTC_SR (Status Register) depends on the value of TIMEVSEL. 0: Minute change. 1: Hour change. 2: Every day at midnight. 3: Every day at noon. • CALEVSEL: Calendar Event Selection The event that generates the flag CALEV in RTC_SR depends on the value of CALEVSEL. 0: Week change (every Monday at time 00:00:00). 1: Month change (every 01 of each month at time 00:00:00). 2, 3: Year change (every January 1 at time 00:00:00). SAM9M11 [DATASHEET] 99 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

13.6.2 RTC Mode Register Name: RTC_MR Address: 0xFFFFFDB4 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – HRMOD • HRMOD: 12-/24-hour Mode 0: 24-hour mode is selected. 1: 12-hour mode is selected. All non-significant bits read zero. 100 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

13.6.3 RTC Time Register Name: RTC_TIMR Address: 0xFFFFFDB8 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – AMPM HOUR 15 14 13 12 11 10 9 8 – MIN 7 6 5 4 3 2 1 0 – SEC • SEC: Current Second The range that can be set is 0–59 (BCD). The lowest four bits encode the units. The higher bits encode the tens. • MIN: Current Minute The range that can be set is 0–59 (BCD). The lowest four bits encode the units. The higher bits encode the tens. • HOUR: Current Hour The range that can be set is 1–12 (BCD) in 12-hour mode or 0–23 (BCD) in 24-hour mode. • AMPM: Ante Meridiem Post Meridiem Indicator This bit is the AM/PM indicator in 12-hour mode. 0: AM. 1: PM. All non-significant bits read zero. SAM9M11 [DATASHEET] 101 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

13.6.4 RTC Calendar Register Name: RTC_CALR Address: 0xFFFFFDBC Access: Read/Write 31 30 29 28 27 26 25 24 – – DATE 23 22 21 20 19 18 17 16 DAY MONTH 15 14 13 12 11 10 9 8 YEAR 7 6 5 4 3 2 1 0 – CENT • CENT: Current Century The range that can be set is 19–20 (BCD). The lowest four bits encode the units. The higher bits encode the tens. • YEAR: Current Year The range that can be set is 00–99 (BCD). The lowest four bits encode the units. The higher bits encode the tens. • MONTH: Current Month The range that can be set is 01–12 (BCD). The lowest four bits encode the units. The higher bits encode the tens. • DAY: Current Day in Current Week The range that can be set is 1–7 (BCD). The coding of the number (which number represents which day) is user-defined as it has no effect on the date counter. • DATE: Current Day in Current Month The range that can be set is 01–31 (BCD). The lowest four bits encode the units. The higher bits encode the tens. All non-significant bits read zero. 102 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

13.6.5 RTC Time Alarm Register Name: RTC_TIMALR Address: 0xFFFFFDC0 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 HOUREN AMPM HOUR 15 14 13 12 11 10 9 8 MINEN MIN 7 6 5 4 3 2 1 0 SECEN SEC • SEC: Second Alarm This field is the alarm field corresponding to the BCD-coded second counter. • SECEN: Second Alarm Enable 0: The second-matching alarm is disabled. 1: The second-matching alarm is enabled. • MIN: Minute Alarm This field is the alarm field corresponding to the BCD-coded minute counter. • MINEN: Minute Alarm Enable 0: The minute-matching alarm is disabled. 1: The minute-matching alarm is enabled. • HOUR: Hour Alarm This field is the alarm field corresponding to the BCD-coded hour counter. • AMPM: AM/PM Indicator This field is the alarm field corresponding to the BCD-coded hour counter. • HOUREN: Hour Alarm Enable 0: The hour-matching alarm is disabled. 1: The hour-matching alarm is enabled. SAM9M11 [DATASHEET] 103 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

13.6.6 RTC Calendar Alarm Register Name: RTC_CALALR Address: 0xFFFFFDC4 Access: Read/Write 31 30 29 28 27 26 25 24 DATEEN – DATE 23 22 21 20 19 18 17 16 MTHEN – – MONTH 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – – • MONTH: Month Alarm This field is the alarm field corresponding to the BCD-coded month counter. • MTHEN: Month Alarm Enable 0: The month-matching alarm is disabled. 1: The month-matching alarm is enabled. • DATE: Date Alarm This field is the alarm field corresponding to the BCD-coded date counter. • DATEEN: Date Alarm Enable 0: The date-matching alarm is disabled. 1: The date-matching alarm is enabled. 104 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

13.6.7 RTC Status Register Name: RTC_SR Address: 0xFFFFFDC8 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – CALEV TIMEV SEC ALARM ACKUPD • ACKUPD: Acknowledge for Update 0: Time and calendar registers cannot be updated. 1: Time and calendar registers can be updated. • ALARM: Alarm Flag 0: No alarm matching condition occurred. 1: An alarm matching condition has occurred. • SEC: Second Event 0: No second event has occurred since the last clear. 1: At least one second event has occurred since the last clear. • TIMEV: Time Event 0: No time event has occurred since the last clear. 1: At least one time event has occurred since the last clear. The time event is selected in the TIMEVSEL field in RTC_CTRL (Control Register) and can be any one of the following events: minute change, hour change, noon, midnight (day change). • CALEV: Calendar Event 0: No calendar event has occurred since the last clear. 1: At least one calendar event has occurred since the last clear. The calendar event is selected in the CALEVSEL field in RTC_CR and can be any one of the following events: week change, month change and year change. SAM9M11 [DATASHEET] 105 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

13.6.8 RTC Status Clear Command Register Name: RTC_SCCR Address: 0xFFFFFDCC Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – CALCLR TIMCLR SECCLR ALRCLR ACKCLR • ACKCLR: Acknowledge Clear 0: No effect. 1: Clears corresponding status flag in the Status Register (RTC_SR). • ALRCLR: Alarm Clear 0: No effect. 1: Clears corresponding status flag in the Status Register (RTC_SR). • SECCLR: Second Clear 0: No effect. 1: Clears corresponding status flag in the Status Register (RTC_SR). • TIMCLR: Time Clear 0: No effect. 1: Clears corresponding status flag in the Status Register (RTC_SR). • CALCLR: Calendar Clear 0: No effect. 1: Clears corresponding status flag in the Status Register (RTC_SR). 106 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

13.6.9 RTC Interrupt Enable Register Name: RTC_IER Address: 0xFFFFFDD0 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – CALEN TIMEN SECEN ALREN ACKEN • ACKEN: Acknowledge Update Interrupt Enable 0: No effect. 1: The acknowledge for update interrupt is enabled. • ALREN: Alarm Interrupt Enable 0: No effect. 1: The alarm interrupt is enabled. • SECEN: Second Event Interrupt Enable 0: No effect. 1: The second periodic interrupt is enabled. • TIMEN: Time Event Interrupt Enable 0: No effect. 1: The selected time event interrupt is enabled. • CALEN: Calendar Event Interrupt Enable 0: No effect. 1: The selected calendar event interrupt is enabled. SAM9M11 [DATASHEET] 107 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

13.6.10 RTC Interrupt Disable Register Name: RTC_IDR Address: 0xFFFFFDD4 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – CALDIS TIMDIS SECDIS ALRDIS ACKDIS • ACKDIS: Acknowledge Update Interrupt Disable 0: No effect. 1: The acknowledge for update interrupt is disabled. • ALRDIS: Alarm Interrupt Disable 0: No effect. 1: The alarm interrupt is disabled. • SECDIS: Second Event Interrupt Disable 0: No effect. 1: The second periodic interrupt is disabled. • TIMDIS: Time Event Interrupt Disable 0: No effect. 1: The selected time event interrupt is disabled. • CALDIS: Calendar Event Interrupt Disable 0: No effect. 1: The selected calendar event interrupt is disabled. 108 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

13.6.11 RTC Interrupt Mask Register Name: RTC_IMR Address: 0xFFFFFDD8 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – CAL TIM SEC ALR ACK • ACK: Acknowledge Update Interrupt Mask 0: The acknowledge for update interrupt is disabled. 1: The acknowledge for update interrupt is enabled. • ALR: Alarm Interrupt Mask 0: The alarm interrupt is disabled. 1: The alarm interrupt is enabled. • SEC: Second Event Interrupt Mask 0: The second periodic interrupt is disabled. 1: The second periodic interrupt is enabled. • TIM: Time Event Interrupt Mask 0: The selected time event interrupt is disabled. 1: The selected time event interrupt is enabled. • CAL: Calendar Event Interrupt Mask 0: The selected calendar event interrupt is disabled. 1: The selected calendar event interrupt is enabled. SAM9M11 [DATASHEET] 109 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

13.6.12 RTC Valid Entry Register Name: RTC_VER Address: 0xFFFFFDDC Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – NVCALALR NVTIMALR NVCAL NVTIM • NVTIM: Non-valid Time 0: No invalid data has been detected in RTC_TIMR (Time Register). 1: RTC_TIMR has contained invalid data since it was last programmed. • NVCAL: Non-valid Calendar 0: No invalid data has been detected in RTC_CALR (Calendar Register). 1: RTC_CALR has contained invalid data since it was last programmed. • NVTIMALR: Non-valid Time Alarm 0: No invalid data has been detected in RTC_TIMALR (Time Alarm Register). 1: RTC_TIMALR has contained invalid data since it was last programmed. • NVCALALR: Non-valid Calendar Alarm 0: No invalid data has been detected in RTC_CALALR (Calendar Alarm Register). 1: RTC_CALALR has contained invalid data since it was last programmed. 110 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

14. Periodic Interval Timer (PIT) 14.1 Description The Periodic Interval Timer (PIT) provides the operating system’s scheduler interrupt. It is designed to offer maximum accuracy and efficient management, even for systems with long response time. 14.2 Embedded Characteristics  Includes a 20-bit Periodic Counter, with less than 1µs accuracy  Includes a 12-bit Interval Overlay Counter  Real-time OS or Linux/WinCE compliant tick generator 14.3 Block Diagram Figure 14-1. Periodic Interval Timer PIT_MR PIV = ? PIT_MR PITIEN set pit_irq 0 PIT_SR PITS reset 0 0 1 12-bit 0 1 Adder read PIT_PIVR MCK 20-bit Counter MCK/16 Prescaler CPIV PIT_PIVR PICNT PIT_PIIR CPIV PICNT SAM9M11 [DATASHEET] 111 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

14.4 Functional Description The Periodic Interval Timer aims at providing periodic interrupts for use by operating systems. The PIT provides a programmable overflow counter and a reset-on-read feature. It is built around two counters: a 20-bit CPIV counter and a 12-bit PICNT counter. Both counters work at Master Clock /16. The first 20-bit CPIV counter increments from 0 up to a programmable overflow value set in the field PIV of the Mode Register (PIT_MR). When the counter CPIV reaches this value, it resets to 0 and increments the Periodic Interval Counter, PICNT. The status bit PITS in the Status Register (PIT_SR) rises and triggers an interrupt, provided the interrupt is enabled (PITIEN in PIT_MR). Writing a new PIV value in PIT_MR does not reset/restart the counters. When CPIV and PICNT values are obtained by reading the Periodic Interval Value Register (PIT_PIVR), the overflow counter (PICNT) is reset and the PITS is cleared, thus acknowledging the interrupt. The value of PICNT gives the number of periodic intervals elapsed since the last read of PIT_PIVR. When CPIV and PICNT values are obtained by reading the Periodic Interval Image Register (PIT_PIIR), there is no effect on the counters CPIV and PICNT, nor on the bit PITS. For example, a profiler can read PIT_PIIR without clearing any pending interrupt, whereas a timer interrupt clears the interrupt by reading PIT_PIVR. The PIT may be enabled/disabled using the PITEN bit in the PIT_MR (disabled on reset). The PITEN bit only becomes effective when the CPIV value is 0. Figure 14-2 illustrates the PIT counting. After the PIT Enable bit is reset (PITEN = 0), the CPIV goes on counting until the PIV value is reached, and is then reset. PIT restarts counting, only if the PITEN is set again. The PIT is stopped when the core enters debug state. Figure 14-2. Enabling/Disabling PIT with PITEN APB cycle APB cycle MCK 15 restarts MCK Prescaler MCK Prescaler 0 PITEN CPIV 0 1 PIV - 1 PIV 0 1 PICNT 0 1 0 PITS (PIT_SR) APB Interface read PIT_PIVR 112 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

14.5 Periodic Interval Timer (PIT) User Interface Table 14-1. Register Mapping Offset Register Name Access Reset 0x00 Mode Register PIT_MR Read/Write 0x000F_FFFF 0x04 Status Register PIT_SR Read-only 0x0000_0000 0x08 Periodic Interval Value Register PIT_PIVR Read-only 0x0000_0000 0x0C Periodic Interval Image Register PIT_PIIR Read-only 0x0000_0000 SAM9M11 [DATASHEET] 113 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

14.5.1 Periodic Interval Timer Mode Register Name: PIT_MR Address: 0xFFFFFD30 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – PITIEN PITEN 23 22 21 20 19 18 17 16 – – – – PIV 15 14 13 12 11 10 9 8 PIV 7 6 5 4 3 2 1 0 PIV • PIV: Periodic Interval Value Defines the value compared with the primary 20-bit counter of the Periodic Interval Timer (CPIV). The period is equal to (PIV + 1). • PITEN: Period Interval Timer Enabled 0: The Periodic Interval Timer is disabled when the PIV value is reached. 1: The Periodic Interval Timer is enabled. • PITIEN: Periodic Interval Timer Interrupt Enable 0: The bit PITS in PIT_SR has no effect on interrupt. 1: The bit PITS in PIT_SR asserts interrupt. 114 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

14.5.2 Periodic Interval Timer Status Register Name: PIT_SR Address: 0xFFFFFD34 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – PITS • PITS: Periodic Interval Timer Status 0: The Periodic Interval timer has not reached PIV since the last read of PIT_PIVR. 1: The Periodic Interval timer has reached PIV since the last read of PIT_PIVR. SAM9M11 [DATASHEET] 115 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

14.5.3 Periodic Interval Timer Value Register Name: PIT_PIVR Address: 0xFFFFFD38 Access: Read-only 31 30 29 28 27 26 25 24 PICNT 23 22 21 20 19 18 17 16 PICNT CPIV 15 14 13 12 11 10 9 8 CPIV 7 6 5 4 3 2 1 0 CPIV Reading this register clears PITS in PIT_SR. • CPIV: Current Periodic Interval Value Returns the current value of the periodic interval timer. • PICNT: Periodic Interval Counter Returns the number of occurrences of periodic intervals since the last read of PIT_PIVR. 116 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

14.5.4 Periodic Interval Timer Image Register Name: PIT_PIIR Address: 0xFFFFFD3C Access: Read-only 31 30 29 28 27 26 25 24 PICNT 23 22 21 20 19 18 17 16 PICNT CPIV 15 14 13 12 11 10 9 8 CPIV 7 6 5 4 3 2 1 0 CPIV • CPIV: Current Periodic Interval Value Returns the current value of the periodic interval timer. • PICNT: Periodic Interval Counter Returns the number of occurrences of periodic intervals since the last read of PIT_PIVR. SAM9M11 [DATASHEET] 117 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

15. Watchdog Timer (WDT) 15.1 Description The Watchdog Timer can be used to prevent system lock-up if the software becomes trapped in a deadlock. It features a 12-bit down counter that allows a watchdog period of up to 16 seconds (slow clock at 32.768 kHz). It can generate a general reset or a processor reset only. In addition, it can be stopped while the processor is in debug mode or idle mode. 15.2 Embedded Characteristics  16-bit key-protected only-once-Programmable Counter  Windowed, prevents the processor to be in a dead-lock on the watchdog access 15.3 Block Diagram Figure 15-1. Watchdog Timer Block Diagram write WDT_MR WDT_MR WDV WDT_CR WDRSTT reload 1 0 12-bit Down Counter WDT_MR reload WDD Current 1/128 SLCK Value <= WDD WDT_MR WDRSTEN = 0 wdt_fault (to Reset Controller) set WDUNF wdt_int set reset WDERR read WDT_SR reset WDFIEN or reset WDT_MR 118 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

15.4 Functional Description The Watchdog Timer can be used to prevent system lock-up if the software becomes trapped in a deadlock. It is supplied with VDDCORE. It restarts with initial values on processor reset. The Watchdog is built around a 12-bit down counter, which is loaded with the value defined in the field WDV of the Mode Register (WDT_MR). The Watchdog Timer uses the Slow Clock divided by 128 to establish the maximum Watchdog period to be 16 seconds (with a typical Slow Clock of 32.768 kHz). After a Processor Reset, the value of WDV is 0xFFF, corresponding to the maximum value of the counter with the external reset generation enabled (field WDRSTEN at 1 after a Backup Reset). This means that a default Watchdog is running at reset, i.e., at power-up. The user must either disable it (by setting the WDDIS bit in WDT_MR) if he does not expect to use it or must reprogram it to meet the maximum Watchdog period the application requires. The Watchdog Mode Register (WDT_MR) can be written only once. Only a processor reset resets it. Writing the WDT_MR reloads the timer with the newly programmed mode parameters. In normal operation, the user reloads the Watchdog at regular intervals before the timer underflow occurs, by writing the Control Register (WDT_CR) with the bit WDRSTT to 1. The Watchdog counter is then immediately reloaded from WDT_MR and restarted, and the Slow Clock 128 divider is reset and restarted. The WDT_CR is write-protected. As a result, writing WDT_CR without the correct hard-coded key has no effect. If an underflow does occur, the “wdt_fault” signal to the Reset Controller is asserted if the bit WDRSTEN is set in the Mode Register (WDT_MR). Moreover, the bit WDUNF is set in the Watchdog Status Register (WDT_SR). To prevent a software deadlock that continuously triggers the Watchdog, the reload of the Watchdog must occur while the Watchdog counter is within a window between 0 and WDD, WDD is defined in the WatchDog Mode Register WDT_MR. Any attempt to restart the Watchdog while the Watchdog counter is between WDV and WDD results in a Watchdog error, even if the Watchdog is disabled. The bit WDERR is updated in the WDT_SR and the “wdt_fault” signal to the Reset Controller is asserted. Note that this feature can be disabled by programming a WDD value greater than or equal to the WDV value. In such a configuration, restarting the Watchdog Timer is permitted in the whole range [0; WDV] and does not generate an error. This is the default configuration on reset (the WDD and WDV values are equal). The status bits WDUNF (Watchdog Underflow) and WDERR (Watchdog Error) trigger an interrupt, provided the bit WDFIEN is set in the mode register. The signal “wdt_fault” to the reset controller causes a Watchdog reset if the WDRSTEN bit is set as already explained in the reset controller programmer Datasheet. In that case, the processor and the Watchdog Timer are reset, and the WDERR and WDUNF flags are reset. If a reset is generated or if WDT_SR is read, the status bits are reset, the interrupt is cleared, and the “wdt_fault” signal to the reset controller is deasserted. Writing the WDT_MR reloads and restarts the down counter. While the processor is in debug state or in idle mode, the counter may be stopped depending on the value programmed for the bits WDIDLEHLT and WDDBGHLT in the WDT_MR. SAM9M11 [DATASHEET] 119 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 15-2. Watchdog Behavior Watchdog Error Watchdog Underflow if WDRSTEN is 1 FFF Normal behavior if WDRSTEN is 0 WDV Forbidden Window WDD Permitted Window 0 WDT_CR = WDRSTT Watchdog Fault 120 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

15.5 Watchdog Timer (WDT) User Interface Table 15-1. Register Mapping Offset Register Name Access Reset 0x00 Control Register WDT_CR Write-only - 0x04 Mode Register WDT_MR Read-write Once 0x3FFF_2FFF 0x08 Status Register WDT_SR Read-only 0x0000_0000 SAM9M11 [DATASHEET] 121 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

15.5.1 Watchdog Timer Control Register Name: WDT_CR Address: 0xFFFFFD40 Access: Write-only 31 30 29 28 27 26 25 24 KEY 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – WDRSTT • WDRSTT: Watchdog Restart 0: No effect. 1: Restarts the Watchdog. • KEY: Password Should be written at value 0xA5. Writing any other value in this field aborts the write operation. 122 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

15.5.2 Watchdog Timer Mode Register Name: WDT_MR Address: 0xFFFFFD44 Access: Read-write Once 31 30 29 28 27 26 25 24 WDIDLEHLT WDDBGHLT WDD 23 22 21 20 19 18 17 16 WDD 15 14 13 12 11 10 9 8 WDDIS WDRPROC WDRSTEN WDFIEN WDV 7 6 5 4 3 2 1 0 WDV • WDV: Watchdog Counter Value Defines the value loaded in the 12-bit Watchdog Counter. • WDFIEN: Watchdog Fault Interrupt Enable 0: A Watchdog fault (underflow or error) has no effect on interrupt. 1: A Watchdog fault (underflow or error) asserts interrupt. • WDRSTEN: Watchdog Reset Enable 0: A Watchdog fault (underflow or error) has no effect on the resets. 1: A Watchdog fault (underflow or error) triggers a Watchdog reset. • WDRPROC: Watchdog Reset Processor 0: If WDRSTEN is 1, a Watchdog fault (underflow or error) activates all resets. 1: If WDRSTEN is 1, a Watchdog fault (underflow or error) activates the processor reset. • WDD: Watchdog Delta Value Defines the permitted range for reloading the Watchdog Timer. If the Watchdog Timer value is less than or equal to WDD, writing WDT_CR with WDRSTT = 1 restarts the timer. If the Watchdog Timer value is greater than WDD, writing WDT_CR with WDRSTT = 1 causes a Watchdog error. • WDDBGHLT: Watchdog Debug Halt 0: The Watchdog runs when the processor is in debug state. 1: The Watchdog stops when the processor is in debug state. • WDIDLEHLT: Watchdog Idle Halt 0: The Watchdog runs when the system is in idle mode. 1: The Watchdog stops when the system is in idle state. • WDDIS: Watchdog Disable 0: Enables the Watchdog Timer. SAM9M11 [DATASHEET] 123 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

1: Disables the Watchdog Timer. 15.5.3 Watchdog Timer Status Register Name: WDT_SR Address: 0xFFFFFD48 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – WDERR WDUNF • WDUNF: Watchdog Underflow 0: No Watchdog underflow occurred since the last read of WDT_SR. 1: At least one Watchdog underflow occurred since the last read of WDT_SR. • WDERR: Watchdog Error 0: No Watchdog error occurred since the last read of WDT_SR. 1: At least one Watchdog error occurred since the last read of WDT_SR. 124 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

16. Shutdown Controller (SHDWC) 16.1 Description The Shutdown Controller controls the power supplies VDDIO and VDDCORE and the wake-up detection on debounced input lines. 16.2 Embedded Characteristics The Shutdown Controller is supplied on VDDBU and allows a software-controllable shutdown of the system through the pin SHDN. An input change of the WKUP pin or an alarm releases the SHDN pin, and thus wakes up the system power supply. 16.3 Block Diagram Figure 16-1. Shutdown Controller Block Diagram SLCK Shutdown Controller SHDW_MR read SHDW_SR CPTWK0 reset WKMODE0 WAKEUP0 SHDW_SR set WKUP0 read SHDW_SR Wake-up reset RTTWKEN SHDW_MR RTTWK SHDW_SR Shutdown SHDN Output RTT Alarm set Controller SHDW_CR read SHDW_SR SHDW Shutdown reset RTCWKEN SHDW_MR RTCWK SHDW_SR RTC Alarm set 16.4 I/O Lines Description Table 16-1. I/O Lines Description Name Description Type WKUP0 Wake-up 0 input Input SHDN Shutdown output Output SAM9M11 [DATASHEET] 125 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

16.5 Product Dependencies 16.5.1 Power Management The Shutdown Controller is continuously clocked by Slow Clock. The Power Management Controller has no effect on the behavior of the Shutdown Controller. 16.6 Functional Description The Shutdown Controller manages the main power supply. To do so, it is supplied with VDDBU and manages wake-up input pins and one output pin, SHDN. A typical application connects the pin SHDN to the shutdown input of the DC/DC Converter providing the main power supplies of the system, and especially VDDCORE and/or VDDIO. The wake-up inputs (WKUP0) connect to any push-buttons or signal that wake up the system. The software is able to control the pin SHDN by writing the Shutdown Control Register (SHDW_CR) with the bit SHDW at 1. The shutdown is taken into account only 2 slow clock cycles after the write of SHDW_CR. This register is password-protected and so the value written should contain the correct key for the command to be taken into account. As a result, the system should be powered down. A level change on WKUP0 is used as wake-up. Wake-up is configured in the Shutdown Mode Register (SHDW_MR). The transition detector can be programmed to detect either a positive or negative transition or any level change on WKUP0. The detection can also be disabled. Programming is performed by defining WKMODE0. Moreover, a debouncing circuit can be programmed for WKUP0. The debouncing circuit filters pulses on WKUP0 shorter than the programmed number of 16 SLCK cycles in CPTWK0 of the SHDW_MR. If the programmed level change is detected on a pin, a counter starts. When the counter reaches the value programmed in the corresponding field, CPTWK0, the SHDN pin is released. If a new input change is detected before the counter reaches the corresponding value, the counter is stopped and cleared. WAKEUP0 of the Status Register (SHDW_SR) reports the detection of the programmed events on WKUP0 with a reset after the read of SHDW_SR. The Shutdown Controller can be programmed so as to activate the wake-up using the RTT alarm (the detection of the rising edge of the RTT alarm is synchronized with SLCK). This is done by writing the SHDW_MR using the RTTWKEN fields. When enabled, the detection of the RTT alarm is reported in the RTTWK bit of the SHDW_SR Status register. It is reset after the read of SHDW_SR. When using the RTT alarm to wake up the system, the user must ensure that the RTT alarm status flag is cleared before shutting down the system. Otherwise, no rising edge of the status flag may be detected and the wake-up fails. The Shutdown Controller can be programmed so as to activate the wake-up using the RTC alarm (the detection of the rising edge of the RTC alarm is synchronized with SLCK). This is done by writing the SHDW_MR using the RTCWKEN field. When enabled, the detection of the RTC alarm is reported in the RTCWK bit of the SHDW_SR Status register. It is reset after the read of SHDW_SR. When using the RTC alarm to wake up the system, the user must ensure that the RTC alarm status flag is cleared before shutting down the system. Otherwise, no rising edge of the status flag may be detected and the wake-up fails fail. 126 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

16.7 Shutdown Controller (SHDWC) User Interface Table 16-2. Register Mapping Offset Register Name Access Reset 0x00 Shutdown Control Register SHDW_CR Write-only - 0x04 Shutdown Mode Register SHDW_MR Read/Write 0x0000_0003 0x08 Shutdown Status Register SHDW_SR Read-only 0x0000_0000 SAM9M11 [DATASHEET] 127 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

16.7.1 Shutdown Control Register Name: SHDW_CR Address: 0xFFFFFD10 Access: Write-only 31 30 29 28 27 26 25 24 KEY 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – SHDW • SHDW: Shutdown Command 0: No effect. 1: If KEY is correct, asserts the SHDN pin. • KEY: Password Should be written at value 0xA5. Writing any other value in this field aborts the write operation. 128 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

16.7.2 Shutdown Mode Register Name: SHDW_MR Address: 0xFFFFFD14 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – RTCWKEN RTTWKEN 15 14 13 12 11 10 9 8 – – – – 7 6 5 4 3 2 1 0 CPTWK0 – – WKMODE0 • WKMODE0: Wake-up Mode 0 WKMODE[1:0] Wake-up Input Transition Selection 0 0 None. No detection is performed on the wake-up input 0 1 Low to high level 1 0 High to low level 1 1 Both levels change • CPTWK0: Counter on Wake-up 0 Defines the number of 16 Slow Clock cycles, the level detection on the corresponding input pin shall last before the wake- up event occurs. Because of the internal synchronization of WKUP0, the SHDN pin is released (CPTWK x 16 + 1) Slow Clock cycles after the event on WKUP. • RTTWKEN: Real-time Timer Wake-up Enable 0: The RTT Alarm signal has no effect on the Shutdown Controller. 1: The RTT Alarm signal forces the de-assertion of the SHDN pin. • RTCWKEN: Real-time Clock Wake-up Enable 0: The RTC Alarm signal has no effect on the Shutdown Controller. 1: The RTC Alarm signal forces the de-assertion of the SHDN pin. SAM9M11 [DATASHEET] 129 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

16.7.3 Shutdown Status Register Name: SHDW_SR Address: 0xFFFFFD18 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – RTCWK RTTWK 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – WAKEUP0 • WAKEUP0: Wake-up 0 Status 0: No wake-up event occurred on the corresponding wake-up input since the last read of SHDW_SR. 1: At least one wake-up event occurred on the corresponding wake-up input since the last read of SHDW_SR. • RTTWK: Real-time Timer Wake-up 0: No wake-up alarm from the RTT occurred since the last read of SHDW_SR. 1: At least one wake-up alarm from the RTT occurred since the last read of SHDW_SR. • RTCWK: Real-time Clock Wake-up 0: No wake-up alarm from the RTC occurred since the last read of SHDW_SR. 1: At least one wake-up alarm from the RTC occurred since the last read of SHDW_SR. 130 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

17. General Purpose Backup Registers (GPBR) 17.1 Description The System Controller embeds four general-purpose backup registers. 17.2 Embedded Characteristics  128-bit general-purpose backup registers 17.3 General Purpose Backup Registers (GPBR) User Interface Table 17-1. Register Mapping Offset Register Name Access Reset 0x0 General Purpose Backup Register 0 SYS_GPBR0 Read/Write – ... ... ... ... ... 0xC General Purpose Backup Register 3 SYS_GPBR3 Read/Write – SAM9M11 [DATASHEET] 131 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

17.3.1 General Purpose Backup Register x Name: SYS_GPBRx Address: 0xFFFFFD60 [0], 0xFFFFFD64 [1], 0xFFFFFD68 [2], 0xFFFFFD6C [3] Type: Read/Write 31 30 29 28 27 26 25 24 GPBR_VALUEx 23 22 21 20 19 18 17 16 GPBR_VALUEx 15 14 13 12 11 10 9 8 GPBR_VALUEx 7 6 5 4 3 2 1 0 GPBR_VALUEx • GPBR_VALUEx: Value of GPBR x 132 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18. Bus Matrix (MATRIX) 18.1 Description The Bus Matrix implements a multi-layer AHB, based on the AHB-Lite protocol, that enables parallel access paths between multiple AHB masters and slaves in a system, thus increasing the overall bandwidth. The Bus Matrix interconnects up to 16 AHB masters to up to 16 AHB slaves. The normal latency to connect a master to a slave is one cycle except for the default master of the accessed slave which is connected directly (zero cycle latency). The Bus Matrix user interface is compliant with ARM Advanced Peripheral Bus and provides a Chip Configuration User Interface with Registers that allow the Bus Matrix to support application specific features. 18.2 Embedded Characteristics  12-layer Matrix, handling requests from 11 masters  Programmable Arbitration strategy ̶ Fixed-priority Arbitration ̶ Round-Robin Arbitration, either with no default master, last accessed default master or fixed default master  Burst Management ̶ Breaking with Slot Cycle Limit Support ̶ Undefined Burst Length Support  One Address Decoder provided per Master  Boot Mode Select ̶ Non-volatile Boot Memory can be internal ROM or external memory on EBI_NCS0 ̶ Selection is made by General purpose NVM bit sampled at reset  Remap Command ̶ Allows Remapping of an Internal SRAM in Place of the Boot Non-Volatile Memory (ROM or External Flash) ̶ Allows Handling of Dynamic Exception Vectors SAM9M11 [DATASHEET] 133 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.2.1 Matrix Masters The Bus Matrix of the SAM9M11 manages Masters, thus each master can perform an access concurrently with others, depending on whether the slave it accesses is available. Each Master has its own decoder, which can be defined specifically for each master. In order to simplify the addressing, all the masters have the same decodings. Table 18-1. List of Bus Matrix Masters Master 0 ARM926™ Instruction Master 1 ARM926 Data Master 2 Peripheral DMA Controller (PDC) Master 3 USB HOST OHCI Master 4 DMA Master 5 DMA Master 6 ISI Controller DMA Master 7 LCD DMA Master 8 Ethernet MAC DMA Master 9 USB Device High Speed DMA Master 10 USB Host High Speed EHCI DMA Master 11 Video Decoder 18.2.2 Matrix Slaves Each Slave has its own arbiter, thus allowing a different arbitration per Slave to be programmed. Table 18-2. List of Bus Matrix Slaves Slave 0 Internal SRAM Internal ROM USB OHCI USB EHCI Slave 1 UDP High Speed RAM LCD User Interface Video Decoder Slave 2 DDR Port 0 Slave 3 DDR Port 1 Slave 4 DDR Port 2 Slave 5 DDR Port 3 Slave 6 External Bus Interface Slave 7 Internal Peripherals 134 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.2.3 Masters to Slaves Access All the Masters can normally access all the Slaves. However, some paths do not make sense, such as allowing access from the Ethernet MAC to the internal peripherals. Thus, these paths are forbidden or simply not wired, and shown as “-” in the following tables. The four DDR ports are connected differently according to the application device. The user can disable the Video Decoder in the Video Mode Configuration Register (bit VDEC_SEL) in the Chip Configuration User Interface.  When the Video Decoder is not enabled (VDEC_SEL = 0), the ARM instruction and data are respectively connected to DDR Port 0 and DDR Port 1. The other masters share DDR Port 2 and DDR Port 3.  When the Video Decoder is enabled (VDEC_SEL = 1), DDR Port 0 is dedicated to the video controller, and DDR Port 1 to the LCD controller. The remaining masters share DDR Port 2 and DDR Port 3. Figure 18-1. Video Mode Configuration VDEC_SEL Video Decoder LCD + Post DDR_S0 Processing ARM I DMA DDR_S1 ARM D AR AR M M D I VDEC_SEL DDR_S2 MATRIX DDR_S3 SAM9M11 [DATASHEET] 135 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 18-3. SAM9M11 Masters to Slaves Access with VDEC_SEL = 0 Master 0 1 2 3 4 & 5 6 7 8 9 10 11 ARM ARM USB Host ISI LCD Ethernet USB USB Host Slave 926 Instr. 926 Data PDC OHCI DMA DMA DMA MAC Device HS EHCI VDEC 0 Internal SRAM 0 X X X X X X - X X X - Internal ROM X X X - - - - - X - - UHP OHCI X X - - - - - - - - - UHP EHCI X X - - - - - - - - - 1 LCD User Int. X X - - - - - - - - - UDPHS RAM X X - - - - - - - - - VDEC X X - - - - - - - - - 2 DDR Port 0 X - - - - - - - - - - 3 DDR Port 1 - X - - - - - - - - - 4 DDR Port 2 - - - - - - - - - - X 5 DDR Port 3 - - X X X X X X X X - 6 EBI X X X X X X X X X X X 7 Internal Peripheral X X X - X - - - - - - Table 18-4. SAM9M11 Masters to Slaves Access with VDEC_SEL = 1 (default) Master 0 1 2 3 4 & 5 6 7 8 9 10 11 ARM ARM USB Host ISI LCD Ethernet USB USB Host Slave 926 Instr. 926 Data PDC OHCI DMA DMA DMA MAC Device HS EHCI VDEC 0 Internal SRAM 0 X X X X X X - X X X - Internal ROM X X X - - - - - X - - UHP OHCI X X - - - - - - - - - UHP EHCI X X - - - - - - - - - 1 LCD User Int. X X - - - - - - - - - UDPHS RAM X X - - - - - - - - - VDEC X X - - - - - - - - - 2 DDR Port 0 - - - - - - - - - - X 3 DDR Port 1 - - - - - - X - - - - 4 DDR Port 2 X - - - - - - - - - - 5 DDR Port 3 - X X X X X - X X X - 6 EBI X X X X X X X X X X X 7 Internal Peripheral X X X - X - - - - - - Table 18-5 summarizes the Slave Memory Mapping for each connected Master, depending on the Remap status (RCBx bit in Bus Matrix Master Remap Control Register MATRIX_MRCR) and the BMS state at reset. 136 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 18-5. Internal Memory Mapping Master RCBx = 0 RCBx = 1 Slave Base Address BMS = 1 BMS = 0 0x0000 0000 Internal ROM EBI NCS0 Internal SRAM 18.3 Memory Mapping The Bus Matrix provides one decoder for every AHB master interface. The decoder offers each AHB master several memory mappings. In fact, depending on the product, each memory area may be assigned to several slaves. Booting at the same address while using different AHB slaves (i.e., external RAM, internal ROM or internal Flash, etc.) becomes possible. The Bus Matrix user interface provides Master Remap Control Register (MATRIX_MRCR) that performs remap action for every master independently. 18.4 Special Bus Granting Mechanism The Bus Matrix provides some speculative bus granting techniques in order to anticipate access requests from some masters. This mechanism reduces latency at first access of a burst or single transfer as long as the slave is free from any other master access, but does not provide any benefit as soon as the slave is continuously accessed by more than one master, since arbitration is pipelined and then has no negative effect on the slave bandwidth or access latency. This bus granting mechanism sets a different default master for every slave. At the end of the current access, if no other request is pending, the slave remains connected to its associated default master. A slave can be associated with three kinds of default masters: no default master, last access master and fixed default master. To change from one kind of default master to another, the Bus Matrix user interface provides the Slave Configuration Registers, one for each slave, that set a default master for each slave. The Slave Configuration Register contains two fields: DEFMSTR_TYPE and FIXED_DEFMSTR. The 2-bit DEFMSTR_TYPE field selects the default master type (no default, last access master, fixed default master), whereas the 4-bit FIXED_DEFMSTR field selects a fixed default master provided that DEFMSTR_TYPE is set to fixed default master. Please refer to Section 18.7.2 “Bus Matrix Slave Configuration Registers” on page 145. 18.4.1 No Default Master After the end of the current access, if no other request is pending, the slave is disconnected from all masters. No Default Master suits low-power mode. This configuration incurs one latency clock cycle for the first access of a burst after bus Idle. Arbitration without default master may be used for masters that perform significant bursts or several transfers with no Idle in between, or if the slave bus bandwidth is widely used by one or more masters. This configuration provides no benefit on access latency or bandwidth when reaching maximum slave bus throughput whatever is the number of requesting masters. 18.4.2 Last Access Master After the end of the current access, if no other request is pending, the slave remains connected to the last master that performed an access request. SAM9M11 [DATASHEET] 137 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

This allows the Bus Matrix to remove the one latency cycle for the last master that accessed the slave. Other non privileged masters still get one latency clock cycle if they want to access the same slave. This technique is useful for masters that mainly perform single accesses or short bursts with some Idle cycles in between. This configuration provides no benefit on access latency or bandwidth when reaching maximum slave bus throughput whatever is the number of requesting masters. 18.4.3 Fixed Default Master After the end of the current access, if no other request is pending, the slave connects to its fixed default master. Unlike last access master, the fixed master does not change unless the user modifies it by a software action (field FIXED_DEFMSTR of the related MATRIX_SCFG). This allows the Bus Matrix arbiters to remove the one latency clock cycle for the fixed default master of the slave. Every request attempted by this fixed default master will not cause any arbitration latency whereas other non privileged masters will still get one latency cycle. This technique is useful for a master that mainly perform single accesses or short bursts with some Idle cycles in between. This configuration provides no benefit on access latency or bandwidth when reaching maximum slave bus throughput whatever is the number of requesting masters. 18.5 Arbitration The Bus Matrix provides an arbitration mechanism that reduces latency when conflict cases occur, i.e., when two or more masters try to access the same slave at the same time. One arbiter per AHB slave is provided, thus arbitrating each slave differently. The Bus Matrix provides the user with the possibility of choosing between two arbitration types or mixing them for each slave: 1. Round-Robin Arbitration (default) 2. Fixed Priority Arbitration The resulting algorithm may be complemented by selecting a default master configuration for each slave. When a re-arbitration must be done, specific conditions apply. See Section 18.5.1 “Arbitration Scheduling”. 18.5.1 Arbitration Scheduling Each arbiter has the ability to arbitrate between two or more different master requests. In order to avoid burst breaking and also to provide the maximum throughput for slave interfaces, arbitration may only take place during the following cycles: 1. Idle Cycles: When a slave is not connected to any master or is connected to a master which is not currently accessing it. 2. Single Cycles: When a slave is currently doing a single access. 3. End of Burst Cycles: When the current cycle is the last cycle of a burst transfer. For defined length burst, predicted end of burst matches the size of the transfer but is managed differently for undefined length burst. See “Undefined Length Burst Arbitration” on page 139. 4. Slot Cycle Limit: When the slot cycle counter has reached the limit value indicating that the current master access is too long and must be broken. See “Slot Cycle Limit Arbitration” on page 139. 138 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.5.1.1Undefined Length Burst Arbitration In order to optimize AHB burst lengths and arbitration, it may be interesting to set a maximum for undefined length bursts (INCR). The Bus Matrix provides specific logic in order to re-arbitrate before the end of the INCR transfer. A predicted end of burst is used as a defined length burst transfer and can be selected from among the following Undefined Length Burst Type (ULBT) possibilities: 1. Unlimited: No predicted end of burst is generated and therefore INCR burst transfer will not be broken by this way, but will be able to complete unless broken at the Slot Cycle Limit. This is normally the default and should be let as is in order to be able to allow full 1 Kilobyte AHB intra-boundary 256-beat word bursts performed by some Atmel AHB masters. 2. 1-beat bursts: Predicted end of burst is generated at each single transfer inside the INCR transfer. 3. 4-beat bursts: Predicted end of burst is generated at the end of each 4-beat boundary inside INCR transfer. 4. 8-beat bursts: Predicted end of burst is generated at the end of each 8-beat boundary inside INCR transfer. 5. 16-beat bursts: Predicted end of burst is generated at the end of each 16-beat boundary inside INCR transfer. 6. 32-beat bursts: Predicted end of burst is generated at the end of each 32-beat boundary inside INCR transfer. 7. 64-beat bursts: Predicted end of burst is generated at the end of each 64-beat boundary inside INCR transfer. 8. 128-beat bursts: Predicted end of burst is generated at the end of each 128-beat boundary inside INCR transfer. Use of undefined length 16-beat bursts or less is discouraged since this generally decreases significantly overall bus bandwidth due to arbitration and slave latencies at each first access of a burst. If the master does not permanently and continuously request the same slave or has an intrinsically limited average throughput, the ULBT should be let at its default unlimited value, knowing that the AHB specification natively limits all word bursts to 256 beats and double-word bursts to 128 beats because of its 1 Kilobyte address boundaries. Unless duly needed the ULBT should be let to its default 0 value for power saving. This selection can be done through the field ULBT of the Master Configuration Registers (MATRIX_MCFG). 18.5.1.2Slot Cycle Limit Arbitration The Bus Matrix contains specific logic to break long accesses, such as back to back undefined length bursts or very long bursts on a very slow slave (e.g., an external low speed memory). At each arbitration time a counter is loaded with the value previously written in the SLOT_CYCLE field of the related Slave Configuration Register (MATRIX_SCFG) and decreased at each clock cycle. When the counter elapses, the arbiter has the ability to re- arbitrate at the end of the current AHB bus access cycle. Unless some master has a very tight access latency constraint which could lead to data overflow or underflow due to a badly undersized internal fifo with respect to its throughput, the Slot Cycle Limit should be disabled (SLOT_CYCLE = 0) or let to its default maximum value in order not to inefficiently break long bursts performed by some Atmel masters. However, the Slot Cycle Limit should not be disabled in the very particular case of a master capable of accessing the slave by performing back to back undefined length bursts shorter than the number of ULBT beats with no Idle cycle in between, since in this case the arbitration could be frozen all along the bursts sequence. In most cases this feature is not needed and should be disabled for power saving. Warning: This feature cannot prevent any slave from locking its access indefinitely. SAM9M11 [DATASHEET] 139 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.5.2 Arbitration Priority Scheme The bus Matrix arbitration scheme is organized in priority pools. Round-Robin priority is used inside the highest and lowest priority pools, whereas fix level priority is used between priority pools and inside the intermediate priority pools. For each slave, each master x is assigned to one of the slave priority pools through the Priority Registers for Slaves (MxPR fields of MATRIX_PRAS and MATRIX_PRBS). When evaluating masters requests, this programmed priority level always takes precedence. After reset, all the masters are belonging to the lowest priority pool (MxPR = 0) and so are granted bus access in a true Round-Robin fashion. The highest priority pool must be specifically reserved for masters requiring very low access latency. If more than one master belong to this pool, these will be granted bus access in a biased Round-Robin fashion which allow tight and deterministic maximum access latency from AHB bus request. In fact, at worst, any currently high priority master request will be granted after the current bus master access is ended and the other high priority pool masters, if any, have been granted once each. The lowest priority pool shares the remaining bus bandwidth between AHB Masters. Intermediate priority pools allow fine priority tuning. Typically, a moderately latency critical master or a bandwidth only critical master will use such a priority level. The higher the priority level (MxPR value), the higher the master priority. All combination of MxPR values are allowed for all masters and slaves. For example some masters might be assigned to the highest priority pool (round-robin) and the remaining masters to the lowest priority pool (round- robin), with no master for intermediate fix priority levels. If more than one master is requesting the slave bus, whatever are the respective masters priorities, no master will be granted the slave bus for two consecutive runs. A master can only get back to back grants as long as it is the only requesting master. 18.5.2.1Fixed Priority Arbitration This arbitration algorithm is the first and only applied between masters from distinct priority pools. It is also used inside priority pools other than the highest and lowest ones (intermediate priority pools). It allows the Bus Matrix arbiters to dispatch the requests from different masters to the same slave by using the fixed priority defined by the user in the MxPR field for each master inside the MATRIX_PRAS and MATRIX_PRBS Priority Registers. If two or more master requests are active at the same time, the master with the highest priority number MxPR is serviced first. Inside intermediate priority pools, if two or more master requests with the same priority are active at the same time, the master with the highest number is serviced first. 18.5.2.2Round-Robin Arbitration This algorithm is only used inside the highest and lowest priority pools. It allows the Bus Matrix arbiters to dispatch the requests from different masters to the same slave in a fair way. If two or more master requests are active at the same time inside the priority pool, they are serviced in a round-robin increasing master number order. 140 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.6 Write Protect Registers To prevent any single software error that may corrupt MATRIX behavior, the entire MATRIX address space from address offset 0x000 to 0x1FC can be write-protected by setting the WPEN bit in the MATRIX Write Protect Mode Register (MATRIX_WPMR). If a write access to anywhere in the MATRIX address space from address offset 0x000 to 0x1FC is detected, then the WPVS flag in the MATRIX Write Protect Status Register (MATRIX_WPSR) is set and the field WPVSRC indicates in which register the write access has been attempted. The WPVS flag is reset by writing the MATRIX Write Protect Mode Register (MATRIX_WPMR) with the appropriate access key WPKEY. The protected registers are: “Bus Matrix Master Configuration Registers” “Bus Matrix Slave Configuration Registers” “Bus Matrix Priority Registers A For Slaves” “Bus Matrix Priority Registers B For Slaves” “Bus Matrix Master Remap Control Register” SAM9M11 [DATASHEET] 141 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.7 Bus Matrix (MATRIX) User Interface Table 18-6. Register Mapping Offset Register Name Access Reset 0x0000 Master Configuration Register 0 MATRIX_MCFG0 Read/Write 0x00000001 0x0004 Master Configuration Register 1 MATRIX_MCFG1 Read/Write 0x00000000 0x0008 Master Configuration Register 2 MATRIX_MCFG2 Read/Write 0x00000000 0x000C Master Configuration Register 3 MATRIX_MCFG3 Read/Write 0x00000000 0x0010 Master Configuration Register 4 MATRIX_MCFG4 Read/Write 0x00000000 0x0014 Master Configuration Register 5 MATRIX_MCFG5 Read/Write 0x00000000 0x0018 Master Configuration Register 6 MATRIX_MCFG6 Read/Write 0x00000000 0x001C Master Configuration Register 7 MATRIX_MCFG7 Read/Write 0x00000000 0x0020 Master Configuration Register 8 MATRIX_MCFG8 Read/Write 0x00000000 0x0024 Master Configuration Register 9 MATRIX_MCFG9 Read/Write 0x00000000 0x0028 Master Configuration Register 10 MATRIX_MCFG10 Read/Write 0x00000000 0x002C Master Configuration Register 11 MATRIX_MCFG11 Read-write 0x00000000 0x0030–0x003C Reserved – – – 0x0040 Slave Configuration Register 0 MATRIX_SCFG0 Read/Write 0x000001FF 0x0044 Slave Configuration Register 1 MATRIX_SCFG1 Read/Write 0x000001FF 0x0048 Slave Configuration Register 2 MATRIX_SCFG2 Read/Write 0x000001FF 0x004C Slave Configuration Register 3 MATRIX_SCFG3 Read/Write 0x000001FF 0x0050 Slave Configuration Register 4 MATRIX_SCFG4 Read/Write 0x000001FF 0x0054 Slave Configuration Register 5 MATRIX_SCFG5 Read/Write 0x000001FF 0x0058 Slave Configuration Register 6 MATRIX_SCFG6 Read/Write 0x000001FF 0x005C Slave Configuration Register 7 MATRIX_SCFG7 Read/Write 0x000001FF 0x0060–0x007C Reserved – – – 0x0080 Priority Register A for Slave 0 MATRIX_PRAS0 Read/Write 0x00000000 0x0084 Priority Register B for Slave 0 MATRIX_PRBS0 Read/Write 0x00000000 0x0088 Priority Register A for Slave 1 MATRIX_PRAS1 Read/Write 0x00000000 0x008C Priority Register B for Slave 1 MATRIX_PRBS1 Read/Write 0x00000000 0x0090 Priority Register A for Slave 2 MATRIX_PRAS2 Read/Write 0x00000000 0x0094 Priority Register B for Slave 2 MATRIX_PRBS2 Read/Write 0x00000000 0x0098 Priority Register A for Slave 3 MATRIX_PRAS3 Read/Write 0x00000000 0x009C Priority Register B for Slave 3 MATRIX_PRBS3 Read/Write 0x00000000 0x00A0 Priority Register A for Slave 4 MATRIX_PRAS4 Read/Write 0x00000000 0x00A4 Priority Register B for Slave 4 MATRIX_PRBS4 Read/Write 0x00000000 0x00A8 Priority Register A for Slave 5 MATRIX_PRAS5 Read/Write 0x00000000 0x00AC Priority Register B for Slave 5 MATRIX_PRBS5 Read/Write 0x00000000 0x00B0 Priority Register A for Slave 6 MATRIX_PRAS6 Read/Write 0x00000000 142 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 18-6. Register Mapping (Continued) Offset Register Name Access Reset 0x00B4 Priority Register B for Slave 6 MATRIX_PRBS6 Read/Write 0x00000000 0x00B8 Priority Register A for Slave 7 MATRIX_PRAS7 Read/Write 0x00000000 0x00BC Priority Register B for Slave 7 MATRIX_PRBS7 Read/Write 0x00000000 0x00C0–0x00FC Reserved – – – 0x0100 Master Remap Control Register MATRIX_MRCR Read/Write 0x00000000 0x0104–0x010C Reserved – – – 0x0110–0x01E0 Chip Configuration Registers – – – 0x01E4 Write Protect Mode Register MATRIX_WPMR Read/Write 0x00000000 0x01E8 Write Protect Status Register MATRIX_WPSR Read-only 0x00000000 SAM9M11 [DATASHEET] 143 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.7.1 Bus Matrix Master Configuration Registers Name: MATRIX_MCFG0...MATRIX_MCFG11 Address: 0xFFFFEA00 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – ULBT This register can only be written if the WPEN bit is cleared in the “Write Protect Mode Register”. • ULBT: Undefined Length Burst Type 0: Unlimited Length Burst No predicted end of burst is generated and therefore INCR bursts coming from this master can only be broken if the Slave Slot Cycle Limit is reached. If the Slot Cycle Limit is not reached, the burst is normally completed by the master, at the lat- est, on the next AHB 1 Kbyte address boundary, allowing up to 256-beat word bursts or 128-beat double-word bursts. 1: Single Access The undefined length burst is treated as a succession of single accesses, allowing re-arbitration at each beat of the INCR burst. 2: 4-beat Burst The undefined length burst is split into 4-beat bursts, allowing re-arbitration at each 4-beat burst end. 3: 8-beat Burst The undefined length burst is split into 8-beat bursts, allowing re-arbitration at each 8-beat burst end. 4: 16-beat Burst The undefined length burst is split into 16-beat bursts, allowing re-arbitration at each 16-beat burst end. 5: 32-beat Burst The undefined length burst is split into 32-beat bursts, allowing re-arbitration at each 32-beat burst end. 6: 64-beat Burst The undefined length burst is split into 64-beat bursts, allowing re-arbitration at each 64-beat burst end. 7: 128-beat Burst The undefined length burst is split into 128-beat bursts, allowing re-arbitration at each 128-beat burst end. Unless duly needed the ULBT should be let to its default 0 value for power saving. 144 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.7.2 Bus Matrix Slave Configuration Registers Name: MATRIX_SCFG0...MATRIX_SCFG7 Address: 0xFFFFEA40 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – FIXED_DEFMSTR DEFMSTR_TYPE 15 14 13 12 11 10 9 8 – – – – – – – SLOT_CYCLE 7 6 5 4 3 2 1 0 SLOT_CYCLE This register can only be written if the WPEN bit is cleared in the “Write Protect Mode Register”. • SLOT_CYCLE: Maximum Bus Grant Duration for Masters When SLOT_CYCLE AHB clock cycles have elapsed since the last arbitration, a new arbitration takes place so as to let an other master access this slave. If an other master is requesting the slave bus, then the current master burst is broken. If SLOT_CYCLE = 0, the Slot Cycle Limit feature is disabled and bursts always complete unless broken according to the ULBT. This limit has been placed in order to enforce arbitration so as to meet potential latency constraints of masters waiting for slave access or in the particular case of a master performing back to back undefined length bursts indefinitely freezing the arbitration. This limit must not be small. Unreasonably small values break every burst and the Bus Matrix arbitrates without performing any data transfer. The default maximum value is usually an optimal conservative choice. In most cases this feature is not needed and should be disabled for power saving. See “Slot Cycle Limit Arbitration” on page 139 for details. • DEFMSTR_TYPE: Default Master Type 0: No Default Master At the end of the current slave access, if no other master request is pending, the slave is disconnected from all masters. This results in a one clock cycle latency for the first access of a burst transfer or for a single access. 1: Last Default Master At the end of the current slave access, if no other master request is pending, the slave stays connected to the last master having accessed it. This results in not having one clock cycle latency when the last master tries to access the slave again. 2: Fixed Default Master At the end of the current slave access, if no other master request is pending, the slave connects to the fixed master the number that has been written in the FIXED_DEFMSTR field. This results in not having one clock cycle latency when the fixed master tries to access the slave again. SAM9M11 [DATASHEET] 145 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• FIXED_DEFMSTR: Fixed Default Master This is the number of the Default Master for this slave. Only used if DEFMSTR_TYPE is 2. Specifying the number of a master which is not connected to the selected slave is equivalent to setting DEFMSTR_TYPE to 0. 146 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.7.3 Bus Matrix Priority Registers A For Slaves Name: MATRIX_PRAS0...MATRIX_PRAS7 Address: 0xFFFFEA80 [0], 0xFFFFEA88 [1], 0xFFFFEA90 [2], 0xFFFFEA98 [3], 0xFFFFEAA0 [4], 0xFFFFEAA8 [5], 0xFFFFEAB0 [6], 0xFFFFEAB8 [7] Access: Read/Write 31 30 29 28 27 26 25 24 – – M7PR – – M6PR 23 22 21 20 19 18 17 16 – – M5PR – – M4PR 15 14 13 12 11 10 9 8 – – M3PR – – M2PR 7 6 5 4 3 2 1 0 – – M1PR – – M0PR This register can only be written if the WPEN bit is cleared in the “Write Protect Mode Register”. • MxPR: Master x Priority Fixed priority of Master x for accessing the selected slave. The higher the number, the higher the priority. All the masters programmed with the same MxPR value for the slave make up a priority pool. Round-Robin arbitration is used inside the lowest (MxPR = 0) and highest (MxPR = 3) priority pools. Fixed priority is used inside intermediate priority pools (MxPR = 1) and (MxPR = 2). See Section 18.5.2 “Arbitration Priority Scheme” for details. SAM9M11 [DATASHEET] 147 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.7.4 Bus Matrix Priority Registers B For Slaves Name: MATRIX_PRBS0...MATRIX_PRBS7 Address: 0xFFFFEA84 [0], 0xFFFFEA8C [1], 0xFFFFEA94 [2], 0xFFFFEA9C [3], 0xFFFFEAA4 [4], 0xFFFFEAAC [5], 0xFFFFEAB4 [6], 0xFFFFEABC [7] Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – M11PR M10PR 7 6 5 4 3 2 1 0 – – M9PR – – M8PR This register can only be written if the WPEN bit is cleared in the “Write Protect Mode Register”. • MxPR: Master x Priority Fixed priority of Master x for accessing the selected slave. The higher the number, the higher the priority. All the masters programmed with the same MxPR value for the slave make up a priority pool. Round-Robin arbitration is used inside the lowest (MxPR = 0) and highest (MxPR = 3) priority pools. Fixed priority is used inside intermediate priority pools (MxPR = 1) and (MxPR = 2). See Section 18.5.2 “Arbitration Priority Scheme” for details. 148 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.7.5 Bus Matrix Master Remap Control Register Name: MATRIX_MRCR Address: 0xFFFFEB00 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – RCB11 RCB10 RCB9 RCB8 7 6 5 4 3 2 1 0 RCB7 RCB6 RCB5 RCB4 RCB3 RCB2 RCB1 RCB0 This register can only be written if the WPEN bit is cleared in the “Write Protect Mode Register”. • RCB: Remap Command Bit for Master x 0: Disable remapped address decoding for the selected Master 1: Enable remapped address decoding for the selected Master SAM9M11 [DATASHEET] 149 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.7.6 Chip Configuration User Interface Table 18-7. Register Mapping (Chip Configuration User Interface) Offset Register Name Access Reset 0x0110 Bus Matrix TCM Configuration Register CCFG_TCMR Read/Write 0x00000000 0x0114 Reserved – – – 0x0118 Video Mode Configuration CCFG_VMRCR Read-write 0x00000001 0x011C–0x0124 Reserved – – – 0x0128 EBI Chip Select Assignment Register CCFG_EBICSA Read/Write 0x00070000 0x012C–0x01FC Reserved – – – 150 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.7.6.1Bus Matrix TCM Configuration Register Name: CCFG_TCMR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – TCM_NWS – – – 7 6 5 4 3 2 1 0 DTCM_SIZE ITCM_SIZE • ITCM_SIZE: Size of ITCM enabled memory block 000: 0 Kbyte (No ITCM Memory) 110: 32 Kbyte Others: Reserved • DTCM_SIZE: Size of DTCM enabled memory block 000: 0 Kbyte (No DTCM Memory) 110: 32 Kbyte 111: 64 Kbyte Others: Reserved • TCM_NWS: TCM Wait State 0: No TCM Wait State 1: 1 TCM Wait State (only for ration 3:1 or 4:1) SAM9M11 [DATASHEET] 151 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.7.6.2Bus Matrix Video Mode Configuration Register Register: CCFG_VMCR Access: Read-write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – VDEC_SEL • VDEC_SEL: Video Mode Selection 0: Video is OFF 1: Video is ON 152 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.7.6.3EBI Chip Select Assignment Register Name: CCFG_EBICSA Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – DDR_DRIVE EBI_DRIVE 15 14 13 12 11 10 9 8 – – – – – – – EBI_DBPUC 7 6 5 4 3 2 1 0 – – EBI_CS5A EBI_CS4A EBI_CS3A – EBI_CS1A – • EBI_CS1A: EBI Chip Select 1 Assignment 0: EBI Chip Select 1 is assigned to the Static Memory Controller. 1: EBI Chip Select 1 is assigned to the SDRAM Controller. • EBI_CS3A: EBI Chip Select 3 Assignment 0: EBI Chip Select 3 is only assigned to the Static Memory Controller and EBI_NCS3 behaves as defined by the SMC. 1: EBI Chip Select 3 is assigned to the Static Memory Controller and the SmartMedia Logic is activated. • EBI_CS4A: EBI Chip Select 4 Assignment 0: EBI Chip Select 4 is only assigned to the Static Memory Controller and EBI_NCS4 behaves as defined by the SMC. 1: EBI Chip Select 4 is assigned to the Static Memory Controller and the Compact Flash Logic Slot 0 is activated. • EBI_CS5A: EBI Chip Select 5 Assignment 0: EBI Chip Select 5 is only assigned to the Static Memory Controller and EBI_NCS5 behaves as defined by the SMC. 1: EBI Chip Select 5 is assigned to the Static Memory Controller and the Compact Flash Logic Slot 1 is activated. • EBI_DBPUC: EBI Data Bus Pull-up Configuration 0: EBI D0–D15 Data Bus bits are internally pulled-up to the VDDIOM1 power supply. 1: EBI D0–D15 Data Bus bits are not internally pulled-up. • EBI_DRIVE: EBI I/O Drive Configuration EBI I/O drive configuration allows to avoid overshoots and to give the best performance according to the bus load and external memories. Value Drive configuration Conditions 00 Optimized for 1.8V powered memories with Low Drive Maximum load capacitance < 30 pF 01 Optimized for 3.3V powered memories with Low Drive Maximum load capacitance < 30 pF 10 Optimized for 1.8V powered memories with High Drive Maximum load capacitance < 55 pF 11 Optimized for 3.3V powered memories with High Drive Maximum load capacitance < 55 pF SAM9M11 [DATASHEET] 153 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DDR_DRIVE: DDR2 dedicated port I/O slew rate selection DDR2 dedicated port I/O slew rate selection allows to avoid overshoots and to give the best performance according to the bus load and external memories. 0: Low Drive, optimized for load capacitance < 30 pF. 1: High Drive, optimized for load capacitance < 55 pF. Note: This concerns only stand-alone DDR controller. 154 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.7.7 Write Protect Mode Register Name: MATRIX_WPMR Address: 0xFFFFEBE4 Access: Read/Write 31 30 29 28 27 26 25 24 WPKEY 23 22 21 20 19 18 17 16 WPKEY 15 14 13 12 11 10 9 8 WPKEY 7 6 5 4 3 2 1 0 – – – – – – – WPEN For more details on MATRIX_WPMR, refer to Section 18.6 “Write Protect Registers” on page 141. • WPEN: Write Protect Enable 0: Disables the Write Protect if WPKEY corresponds to 0x4D4154 (“MAT” in ASCII). 1: Enables the Write Protect if WPKEY corresponds to 0x4D4154 (“MAT” in ASCII). Protects the entire MATRIX address space from address offset 0x000 to 0x1FC. • WPKEY: Write Protect Key (Write-only) Should be written at value 0x4D4154 (“MAT” in ASCII). Writing any other value in this field aborts the write operation of the WPEN bit. Always reads as 0. SAM9M11 [DATASHEET] 155 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18.7.8 Write Protect Status Register Name: MATRIX_WPSR Address: 0xFFFFEBE8 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 WPVSRC 15 14 13 12 11 10 9 8 WPVSRC 7 6 5 4 3 2 1 0 – – – – – – – WPVS For more details on MATRIX_WPSR, refer to Section 18.6 “Write Protect Registers” on page 141. • WPVS: Write Protect Violation Status 0: No Write Protect Violation has occurred since the last write of the MATRIX_WPMR. 1: At least one Write Protect Violation has occurred since the last write of the MATRIX_WPMR. • WPVSRC: Write Protect Violation Source When WPVS is active, this field indicates the register address offset in which a write access has been attempted. Otherwise it reads as 0. 156 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19. External Memories The product embeds two DDRSDR controllers: DDRSDRC0 and DDRSDRC1. Figure 19-1. DDRSDR Controllers DDRSDRC0 Port 3 Port 2 DDR2 or LP-DDR Port 1 Device Port 0 EBI Bus Matrix DDR2 or LP-DDR DDRSDRC1 or SDR or LP-SDR Device Compact Flash Compact Flash Controller Device NAND Flash NAND Flash Controller Device Static Memory Static Memory Controller Device  DDRSDRC0 is a multi-port DDRSDR controller, standalone. It supports only DDR2 and LPDDR devices. Its user interface is located at 0xFFFFE600.  DDRSDRC1 is a single-port DDRSDR controller, embedded in EBI. It supports DDR2, LPDDR, SDR and LP-SDR devices. Its user interface is located at 0xFFFFE400. Both are described in Section 21. “DDR SDR SDRAM Controller (DDRSDRC)”. All references to SDR and LPSDR must be ignored for DDRSDRC0, multi-port DDRSDR controller. All references to multi-port must be ignored for DDRSDRC1, DDRSDR controller embedded inEBI. SAM9M11 [DATASHEET] 157 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.1 DDRSDRC0 Multi-port DDRSDR Controller 19.1.1 Description The DDR2 Controller is dedicated to 4-port DDR2/LPDDR support. Data transfers are performed through a 16-bit data bus on one chip select. The DDR2 Controller operates with 1.8V Power Supply (VDDIOM0). 19.1.2 Embedded Characteristics 19.1.2.1 DDR2/LPDDR Controller Four AHB Interfaces, Management of All Accesses Maximizes Memory Bandwidth and Minimizes Transaction Latency.  Supports AHB Transfers: ̶ Word, Half Word, Byte Access.  Supports DDR-SDRAM 2, LPDDR  Numerous Configurations Supported ̶ 2K, 4K, 8K, 16K Row Address Memory Parts ̶ DDR2 with Four Internal Banks ̶ DDR2/LPDDR with 16-bit Data Path ̶ One Chip Select for DDR2/LPDDR Device (256 Mbytes Address Space)  Programming Facilities ̶ Multibank Ping-pong Access (Up to 4 Banks Opened at Same Time = Reduces Average Latency of Transactions) ̶ Timing Parameters Specified by Software ̶ Automatic Refresh Operation, Refresh Rate is Programmable ̶ Automatic Update of DS, TCR and PASR Parameters  Energy-saving Capabilities ̶ Self-refresh, Power-down and Deep Power Modes Supported  Power-up Initialization by Software  CAS Latency of 2, 3 Supported  Reset function supported (DDR2)  Auto Precharge Command Not Used  On Die Termination not supported  OCD mode not supported 158 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.1.3 DDR2 Controller Block Diagram Figure 19-2. Organization of the DDR2 DDR2 DDR_A0-DDR_A13 DDR_D0-DDR_D15 DDR_CS Bus Matrix DDR_CKE DDR_RAS, DDR_CAS DDR2 AHB LPDDR DDR_CLK,#DDR_CLK Controller DDR_DQS[0..1] DDR_DQM[0..1] DDR_WE DDR_BA0, DDR_BA1 Address Decoders DDR_VREF User Interface APB SAM9M11 [DATASHEET] 159 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.1.4 I/O Lines Description Table 19-1. DDR2 I/O Lines Description Name Function Type Active Level DDR2/LPDDR Controller DDR_D0–DDR_D15 Data Bus I/O DDR_A0–DDR_A13 Address Bus Output DDR_DQM0–DDR_DQM1 Data Mask Output DDR_DQS0–DDR_DQS1 Data Strobe Output DDR_VREF Reference Voltage for DDR2 operations, typically 0.9V Input DDR_CS Chip Select Output Low DDR_CLK - #DDR_CLK DDR2 Differential Clock Output DDR_CKE Clock enable Output High DDR_RAS Row signal Output Low DDR_CAS Column signal Output Low DDR_WE Write enable Output Low DDR_BA0–DDR_BA1 Bank Select Output 19.1.5 Product Dependencies The pins used for interfacing the DDR2 memory are not multiplexed with the PIO lines. 160 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.1.6 Implementation Example The following hardware configuration is given for illustration only. The user should refer to the memory manufacturer website to check current device availability. Figure 19-3. Hardware Configuration - 2 x 8-bit DDR2 DDR_D[0..15] DDR_A[0..13] MMNN66 MMNN77 DDDDDDDDDDDDDDDDDDDDDDDDDDDDRRRRRRRRRRRRRR______________AAAAAAAAAAAAAA012345678911110123 HHHHKKKKLLJJJJ28372828378372 AAAAAAAAAAAAAA012345678911110123MMTTDD44DD77RRHH226644SSMMDD88RRCCAARRFFMM--DD33QQSSDDDDDDDDDD//DQQNQQQQQQQQMUSS01234567 BBCCDDDDBBAA731982827319 DDDDDDDDDDDDDDDDRRRRRRRR________DDDDDDDD173240156V8 DDDDRR__DDQQSM00 DDDDDDDDDDDDDDDDDDDDDDDDDDDDRRRRRRRRRRRRRR______________AAAAAAAAAAAAAA012345678911110123 HHHHKKKKLLJJJJ28372883728372 AAAAAAAAAAAAAA012345678911110123MMTTDD44DD77RRHH226644SSMMDD88RRCCAARRFFMM--DD33QQSSDDDDDDDDDD//DQQNQQQQQQQQMUSS01234567 BBCCDDDDBBAA738219827319 DDDDDDDDDDDDDDDDRRRRRRRR________DDDDDDDD189111111V5102348 DDDDRR__DDQQSM11 DDDDRR__BBAA10 BBAA01 GGF239 BOBAAD01T VVVVVDDDDDDDDDDL HLEAE19119 CCCCCCCCCC66555555663399557711111111111100000000000000000000nnnnnnnnnnFFFFFFFFFF BBAA01 GGF239 BOBAAD01T VVVVVDDDDDDDDDDL HLEEA19119 CCCCCCCCCC66665566554422660088111111111100000000000000000000nnnnnnnnnnFFFFFFFFFF DDDDDDRRR___CNCKCLKELK CCNKKCEK EFF288 CCCKKKE VVVVVDDDDDDDDDDQQQQQ CACCC99137 CCCCCCCCCC77666677663399551177111111111100000000000000000000nnnnnnnnnnFFFFFFFFFF CNCKKCEK EFF288 CCCKKKE VVVVVDDDDDDDDDDQQQQQ CACCC99137 CCCCCCCCCC77777766664422008866111111111100000000000000000000nnnnnnnnnnFFFFFFFFFF DDR_CS CS G8 CS VREF E2 DDR_VREF CS G8 CS VREF E2 DDR_VREF DDDDDDRRR___RCWAAESS RCNAAWSSE GFF773 CRWAAESS VVVVSSSSSSSS AEJK1339 C1C100770055nnFF RCNAAWSSE GFF773 CRWAAESS VVVVSSSSSSSS AEJK1339 C1C100770066nnFF GLL137 RRRFFFUUU123 VVVVVSSSSSSSSSSQQQQQ BBDDA28728 GLL137 RRRFFFUUU123 VVVVVSSSSSSSSSSQQQQQ BBDDA28728 VSSDL E7 VSSDL E7 19.1.6.1 Software Configuration - 2 x 8-bit DDR2 The following configuration has to be performed:  Initialize the DDR2 Controller depending on the DDR2 device and system bus frequency. The DDR2 initialization sequence is described in Section 21.4.3 “DDR2-SDRAM Initialization”. SAM9M11 [DATASHEET] 161 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.2 External Bus Interface (EBI) 19.2.1 Description The External Bus Interface (EBI) is designed to ensure the successful data transfer between several external devices and the embedded Memory Controller of an ARM-based device. The Static Memory, DDR, SDRAM and ECC Controllers are all featured external Memory Controllers on the EBI. These external Memory Controllers are capable of handling several types of external memory and peripheral devices, such as SRAM, PROM, EPROM, EEPROM, Flash, DDR2 and SDRAM. The EBI operates with 1.8V or 3.3V Power Supply (VDDIOM1). The EBI also supports the CompactFlash and the NAND Flash protocols via integrated circuitry that greatly reduces the requirements for external components. Furthermore, the EBI handles data transfers with up to six external devices, each assigned to six address spaces defined by the embedded Memory Controller. Data transfers are performed through a 16-bit or 32-bit data bus, an address bus of up to 26 bits, up to six chip select lines (NCS[5:0]) and several control pins that are generally multiplexed between the different external Memory Controllers. 19.2.2 Embedded Characteristics The SAM9M11 features an External Bus Interface to interface to a wide range of external memories and to any parallel peripheral. 19.2.2.1 External Bus Interface  Integrates Three External Memory Controllers: ̶ Static Memory Controller ̶ DDR2/SDRAM Controller ̶ SLC NAND Flash ECC Controller  Additional logic for NAND Flash and CompactFlash  Optional Full 32-bit External Data Bus  Up to 26-bit Address Bus (up to 64 Mbytes linear per chip select)  Up to 6 chip selects, Configurable Assignment: ̶ Static Memory Controller on NCS0 ̶ DDR2/SDRAM Controller (SDCS) or Static Memory Controller on NCS1 ̶ Static Memory Controller on NCS2 ̶ Static Memory Controller on NCS3, Optional NAND Flash support ̶ Static Memory Controller on NCS4–NCS5, Optional CompactFlash support 19.2.2.2 Static Memory Controller  8-, 16- or 32-bit Data Bus  Multiple Access Modes supported ̶ Byte Write or Byte Select Lines ̶ Asynchronous read in Page Mode supported (4- up to 32-byte page size)  Multiple device adaptability ̶ Control signals programmable setup, pulse and hold time for each Memory Bank  Multiple Wait State Management ̶ Programmable Wait State Generation ̶ External Wait Request ̶ Programmable Data Float Time  Slow Clock mode supported 162 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.2.2.3 DDR2/SDR Controller  Supports DDR/LPDDR, SDR-SDRAM and LPSDR  Numerous Configurations Supported ̶ 2K, 4K, 8K, 16K Row Address Memory Parts ̶ SDRAM with Four Internal Banks ̶ SDR-SDRAM with 16- or 32- bit Data Path ̶ DDR2/LPDDR with 16-bit Data Path ̶ One Chip Select for SDRAM Device (256 Mbyte Address Space)  Programming Facilities ̶ Multibank Ping-pong Access (Up to 4 Banks Opened at Same Time = Reduces Average Latency of Transactions) ̶ Timing Parameters Specified by Software ̶ Automatic Refresh Operation, Refresh Rate is Programmable ̶ Automatic Update of DS, TCR and PASR Parameters (LPSDR)  Energy-saving Capabilities ̶ Self-refresh, Power-down and Deep Power Modes Supported  SDRAM Power-up Initialization by Software  CAS Latency of 2, 3 Supported  Auto Precharge Command Not Used  SDR-SDRAM with 16-bit Datapath and Eight Columns Not Supported ̶ Clock Frequency Change in Precharge Power-down Mode Not Supported 19.2.2.4 NAND Flash Error Correction Code Controller  Tracking the accesses to a NAND Flash device by triggering on the corresponding chip select  Single bit error correction and 2-bit Random detection  Automatic Hamming Code Calculation while writing ̶ ECC value available in a register  Automatic Hamming Code Calculation while reading ̶ Error Report, including error flag, correctable error flag and word address being detected erroneous ̶ Support 8- or 16-bit NAND Flash devices with 512-, 1024-, 2048- or 4096-bytes pages SAM9M11 [DATASHEET] 163 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.2.3 EBI Block Diagram Figure 19-4. Organization of the External Bus Interface External Bus Interface Bus Matrix D[15:0] DDR2 A0/NBS0 AHB LPDDR A1/NWR2/NBS2 SDRAM Controller A[15:2], A18 A16/BA0 A17/BA1 MUX Static Logic NCS0 Memory Controller NCS1/SDCS NRD/CFOE NWR0/NWE/CFWE NWR1/NBS1/CFIOR NWR3/NBS3/CFIOW SDCK, SDCK#, SDCKE DQM[1:0] CompactFlash DQS[1:0] Logic RAS, CAS SDWE SDA10 NANDOE NAND Flash Logic NANDWE A21/NANDALE A22/NANDCLE D[31:16] ECC Controller A[24:19] PIO A25/CFRNW NCS5/CFCS1 Chip Select Address Decoders Assignor NCS4/CFCS0 NCS3/NANDCS NCS2 NWAIT User Interface CFCE1 CFCE2 DQM[3:2] APB 164 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.2.4 I/O Lines Description Table 19-2. EBI I/O Lines Description Name Function Type Active Level EBI EBI_D0–EBI_D31 Data Bus I/O EBI_A0–EBI_A25 Address Bus Output EBI_NWAIT External Wait Signal Input Low SMC EBI_NCS0–EBI_NCS5 Chip Select Lines Output Low EBI_NWR0–EBI_NWR3 Write Signals Output Low EBI_NRD Read Signal Output Low EBI_NWE Write Enable Output Low EBI_NBS0–EBI_NBS3 Byte Mask Signals Output Low EBI for NAND Flash Support EBI_NANDCS NAND Flash Chip Select Line Output Low EBI_NANDOE NAND Flash Output Enable Output Low EBI_NANDWE NAND Flash Write Enable Output Low DDR2/SDRAM Controller EBI_SDCK, EBI_SDCK# DDR2/SDRAM Differential Clock Output EBI_SDCKE DDR2/SDRAM Clock Enable Output High EBI_SDCS DDR2/SDRAM Controller Chip Select Line Output Low EBI_BA0–EBI_BA1 Bank Select Output EBI_SDWE DDR2/SDRAM Write Enable Output Low EBI_RAS - EBI_CAS Row and Column Signal Output Low EBI_SDA10 SDRAM Address 10 Line Output The connection of some signals through the MUX logic is not direct and depends on the Memory Controller in use at the moment. Table 19-3 details the connections between the two Memory Controllers and the EBI pins. Table 19-3. EBI Pins and Memory Controllers I/O Lines Connections EBIx Pins SDRAM I/O Lines SMC I/O Lines EBI_NWR1/NBS1/CFIOR NBS1 NWR1 EBI_A0/NBS0 Not Supported SMC_A0 EBI_A1/NBS2/NWR2 Not Supported SMC_A1 EBI_A[11:2] SDRAMC_A[9:0] SMC_A[11:2] EBI_SDA10 SDRAMC_A10 Not Supported EBI_A12 Not Supported SMC_A12 EBI_A[14:13] SDRAMC_A[12:11] SMC_A[14:13] EBI_A[25:15] Not Supported SMC_A[25:15] EBI_D[31:0] D[31:0] D[31:0] SAM9M11 [DATASHEET] 165 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.2.5 Application Example 19.2.5.1 Hardware Interface Table 19-4 details the connections to be applied between the EBI pins and the external devices for each Memory Controller. Table 19-4. EBI Pins and External Static Devices Connections Pins of the SMC Interfaced Device 2 x 8-bit 4 x 8-bit 2 x 16-bit 8-bit Static Static 16-bit Static Static Static 32-bit Static Signals: EBI_ Device Devices Device Devices Devices Device D0–D7 D0–D7 D0–D7 D0–D7 D0–D7 D0–D7 D0–D7 D8–D15 – D8–D15 D8–D15 D8–D15 D8–D15 D8–D15 D16–D23 – – – D16–D23 D16–D23 D16–D23 D24–D31 – – – D24–D31 D24–D31 D24–D31 A0/NBS0 A0 – NLB – NLB(3) BE0(5) A1/NWR2/NBS2 A1 A0 A0 WE(2) NLB(4) BE2(5) A2–A25 A[2:25] A[1:24] A[1:24] A[0:23] A[0:23] A[0:23] NCS0 CS CS CS CS CS CS NCS1/DDRSDCS CS CS CS CS CS CS NCS2 CS CS CS CS CS CS NCS3/NANDCS CS CS CS CS CS CS NCS4/CFCS0 CS CS CS CS CS CS NCS5/CFCS1 CS CS CS CS CS CS NRD/CFOE OE OE OE OE OE OE NWR0/NWE WE WE(1) WE WE(2) WE WE NWR1/NBS1 – WE(1) NUB WE(2) NUB(3) BE1(5) NWR3/NBS3 – – – WE(2) NUB(4) BE3(5) Notes: 1. NWR1 enables upper byte writes. NWR0 enables lower byte writes. 2. NWRx enables corresponding byte x writes. (x = 0,1, 2 or 3) 3. NBS0 and NBS1 enable respectively lower and upper bytes of the lower 16-bit word. 4. NBS2 and NBS3 enable respectively lower and upper bytes of the upper 16-bit word. 5. BEx: Byte x Enable (x = 0, 1, 2 or 3) 166 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 19-5. EBI Pins and External Device Connections Pins of the Interfaced Device DDRC SDRAMC SMC CompactFlash Signals: EBI_ DDR2/LPDDR SDRAM CompactFlash True IDE Mode NAND Flash D0–D7 D0–D7 D0–D7 D0–D7 D0–D7 I/O0–I/O7 D8–D15 D8–D15 D8–D15 D8–D15 D8–D15 I/O8–I/O15(4) D16–D31 – D16–D31 – – – A0/NBS0 – – A0 A0 – A1/NWR2/NBS2 – – A1 A1 – DQM0–DQM3 DQM0–DQM3 DQM0–DQM3 – – – DQS0–DQM1 DQS0–DQS1 – – – – A2–A10 A[0:8] A[0:8] A[2:10] A[2:10] – A11 A9 A9 – – – SDA10 A10 A10 – – – A12 – – – – – A13–A14 A[11:12] A[11:12] – – – A15 A13 A13 – – – A16/BA0 BA0 BA0 – – – A17/BA1 BA1 BA1 – – – A18–A20 – – – – – A21/NANDALE – – – – ALE A22/NANDCLE – – REG REG CLE A23–A24 – – – – – A25 – – CFRNW(1) CFRNW(1) – NCS0 – – – – – NCS1/DDRSDCS DDRCS SDCS – – – NCS2 – – – – – NCS3/NANDCS – – – – CE(3) NCS4/CFCS0 – – CFCS0(1) CFCS0(1) – NCS5/CFCS1 – – CFCS1(1) CFCS1(1) – NANDOE – – – – OE NANDWE – – – – WE NRD/CFOE – – OE – – NWR0/NWE/CFWE – – WE WE – NWR1/NBS1/CFIOR – – IOR IOR – NWR3/NBS3/CFIOW – – IOW IOW – CFCE1 – – CE1 CS0 – CFCE2 – – CE2 CS1 – SDCK CK CLK – – – SDCK# CK# – – – – SDCKE CKE CKE – – – RAS RAS RAS – – – SAM9M11 [DATASHEET] 167 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 19-5. EBI Pins and External Device Connections (Continued) Pins of the Interfaced Device DDRC SDRAMC SMC CompactFlash Signals: EBI_ DDR2/LPDDR SDRAM CompactFlash True IDE Mode NAND Flash CAS CAS CAS – – – SDWE WE WE – – – NWAIT(5) – – WAIT WAIT – Pxx(2) – – CD1 or CD2 CD1 or CD2 – Pxx(2) – – – – CE(3) Pxx(2) – – – – RDY Notes: 1. Not directly connected to the CompactFlash slot. Permits the control of the bidirectional buffer between the EBI data bus and the CompactFlash slot. 2. Any PIO line. 3. CE connection depends on the NAND Flash. For standard NAND Flash devices, it must be connected to any free PIO line. For “CE don’t care” NAND Flash devices, it can be either connected to NCS3/NANDCS or to any free PIO line. 4. I/O8–I/O15 pins used only for 16-bit NAND Flash device. 5. EBI_NWAIT signal is multiplexed with PC15. 19.2.5.2 Connection Examples Figure 19-5 shows an example of connections between the EBI and external devices. Figure 19-5. EBI Connections to Memory Devices EBI D0-D31 RAS 2M x 8 2M x 8 CAS SDCK SDRAM SDRAM SSDDCWKEE D0-D7 D0-D7 D8-D15 D0-D7 A0/NBS0 CS CS AD1/QNNNNWWWMWN0RRRRR-2130DD////NNN/QNNBBBWMOSSSE3E213 DSQDWM0ERCCCWDKAALQEKESSM A0-A9, BBAAAA110101 SAAA11D267-AA//BB110AA101, A13 DSDQWME1RCCCWDKAALQEKESSM A0-A9, BBAAAA110101 AASA11D267-AA//BB110AA101, A13 SDA10 A2-A15 A16/BA0 A17/BA1 A18-A25 2M x 8 2M x 8 SDRAM SDRAM D16-D23 D0-D7 D24-D31 D0-D7 NCS0 NCS1/SDCS CS CS NNNNCCCCSSSS2345 SDWERCCCWKAALEKESS A0-A9, BBAAAA110011 AASA11D267-AA//BB110AA101, A13 SDWE RCCCWKAALEKESS A0-A9, BBAAAA111001 SAA1D26-AA/B110A10, A13 DQM DQM A17/BA1 DQM2 DQM3 128K x 8 128K x 8 SRAM SRAM D0-D7 D0-D7 A0-A16 A1-A17 D8-D15 D0-D7 A0-A16 A1-A17 CS CS NRD/NOE OWEE NRD/NOE OWEE A0/NWR0/NBS0 NWR1/NBS1 168 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.2.6 Product Dependencies 19.2.6.1 I/O Lines The pins used for interfacing the External Bus Interface may be multiplexed with the PIO lines. The programmer must first program the PIO controller to assign the External Bus Interface pins to their peripheral function. If I/O lines of the External Bus Interface are not used by the application, they can be used for other purposes by the PIO Controller. 19.2.7 Functional Description The EBI transfers data between the internal AHB Bus (handled by the Bus Matrix) and the external memories or peripheral devices. It controls the waveforms and the parameters of the external address, data and control buses and is composed of the following elements:  the Static Memory Controller (SMC)  the DDR2/SDRAM Controller (DDRSDRC)  the ECC Controller (ECC)  a chip select assignment feature that assigns an AHB address space to the external devices  a multiplex controller circuit that shares the pins between the different Memory Controllers  programmable CompactFlash support logic  programmable NAND Flash support logic 19.2.7.1 Bus Multiplexing The EBI offers a complete set of control signals that share the 32-bit data lines, the address lines of up to 26 bits and the control signals through a multiplex logic operating in function of the memory area requests. Multiplexing is specifically organized in order to guarantee the maintenance of the address and output control lines at a stable state while no external access is being performed. Multiplexing is also designed to respect the data float times defined in the Memory Controllers. Furthermore, refresh cycles of the DDR2 and SDRAM are executed independently by the DDR SDR SDRAM Controller (DDRSDRC) without delaying the other external Memory Controller accesses. 19.2.7.2 Pull-up Control The EBI Chip Select Assignment Register (CCFG_EBICSA) permits enabling of on-chip pull-up resistors on the data bus lines not multiplexed with the PIO Controller lines. The pull-up resistors are enabled after reset. Setting the CCFG_EBICSA.EBI_DBPUC bit disables the pull-up resistors on the lines D0–D15. Enabling the pull-up resistor on the lines D16–D31 can be performed by programming the appropriate PIO controller. 19.2.7.3 Static Memory Controller For information on the Static Memory Controller, refer to Section 20. “Static Memory Controller (SMC)”. 19.2.7.4 DDR2SDRAM Controller For information on the DDR2SDRAM Controller, refer to Section 21. “DDR SDR SDRAM Controller (DDRSDRC)”. 19.2.7.5 ECC Controller For information on the ECC Controller, refer to Section 22. “Error Correction Code Controller (ECC)”. 19.2.7.6 CompactFlash Support The External Bus Interface 0 integrates circuitry that interfaces to CompactFlash devices. The CompactFlash logic is driven by the Static Memory Controller (SMC) on the NCS4 and/or NCS5 address space. Programming the EBI_CS4A and/or EBI_CS5A bit of the CCFG_EBICSA register to the appropriate value enables this logic. (For details on this register, refer to the Section 18. “Bus Matrix (MATRIX)”.) Access to an SAM9M11 [DATASHEET] 169 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

external CompactFlash device is then made by accessing the address space reserved to NCS4 and/or NCS5 (i.e., between 0x5000 0000 and 0x5FFF FFFF for NCS4 and between 0x6000 0000 and 0x6FFF FFFF for NCS5). All CompactFlash modes (Attribute Memory, Common Memory, I/O and True IDE) are supported but the signals _IOIS16 (I/O and True IDE modes) and _ATA SEL (True IDE mode) are not handled. I/O Mode, Common Memory Mode, Attribute Memory Mode and True IDE Mode Within the NCS4 and/or NCS5 address space, the current transfer address is used to distinguish I/O mode, common memory mode, attribute memory mode and True IDE mode. The different modes are accessed through a specific memory mapping as illustrated on Figure 19-6. A[23:21] bits of the transfer address are used to select the desired mode as described in Table 19-6. Figure 19-6. CompactFlash Memory Mapping True IDE Alternate Mode Space Offset 0x00E0 0000 True IDE Mode Space Offset 0x00C0 0000 CF Address Space I/O Mode Space Offset 0x0080 0000 Common Memory Mode Space Offset 0x0040 0000 Attribute Memory Mode Space Offset 0x0000 0000 Note: The A22 pin is used to drive the REG signal of the CompactFlash Device (except in True IDE mode). Table 19-6. CompactFlash Mode Selection A[23:21] Mode Base Address 000 Attribute Memory 010 Common Memory 100 I/O Mode 110 True IDE Mode 111 Alternate True IDE Mode CFCE1 and CFCE2 Signals To cover all types of access, the SMC must be alternatively set to drive 8-bit data bus or 16-bit data bus. The odd byte access on the D[7:0] bus is only possible when the SMC is configured to drive 8-bit memory devices on the corresponding NCS pin (NCS4 or NCS5). The DBW field in the SMC MODE Register corresponding to the NCS4 and/or NCS5 address space must be set as shown in Table 19-7 to enable the required access type. NBS1 and NBS0 are the byte selection signals from SMC and are available when the SMC is set in Byte Select mode on the corresponding Chip Select. The CFCE1 and CFCE2 waveforms are identical to the corresponding NCSx waveform. For details on these waveforms and timings, refer to Section 20. “Static Memory Controller (SMC)”. 170 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 19-7. CFCE1 and CFCE2 Truth Table Mode CFCE2 CFCE1 DBW Comment SMC Access Mode Attribute Memory NBS1 NBS0 16 bits Access to Even Byte on D[7:0] Byte Select Access to Even Byte on D[7:0] NBS1 NBS0 16 bits Byte Select Common Memory Access to Odd Byte on D[15:8] 1 0 8 bits Access to Odd Byte on D[7:0] Access to Even Byte on D[7:0] NBS1 NBS0 16 bits Byte Select I/O Mode Access to Odd Byte on D[15:8] 1 0 8 bits Access to Odd Byte on D[7:0] True IDE Mode Access to Even Byte on D[7:0] Task File 1 0 8 bits Access to Odd Byte on D[7:0] Access to Even Byte on D[7:0] Data Register 1 0 16 bits Byte Select Access to Odd Byte on D[15:8] Alternate True IDE Mode Control Register 0 1 Don’t Care Access to Even Byte on D[7:0] Don’t Care Alternate Status Read Drive Address 0 1 8 bits Access to Odd Byte on D[7:0] Standby Mode or Address Space is not 1 1 – – – assigned to CF Read/Write Signals In I/O mode and True IDE mode, the CompactFlash logic drives the read and write command signals of the SMC on CFIOR and CFIOW signals, while the CFOE and CFWE signals are deactivated. Likewise, in common memory mode and attribute memory mode, the SMC signals are driven on the CFOE and CFWE signals, while the CFIOR and CFIOW are deactivated. Figure 19-7 on page 172 demonstrates a schematic representation of this logic. Attribute memory mode, common memory mode and I/O mode are supported by setting the address setup and hold time on the NCS4 (and/or NCS5) chip select to the appropriate values. For details on these signal waveforms, please refer to Section 20. “Static Memory Controller (SMC)”. SAM9M11 [DATASHEET] 171 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 19-7. CompactFlash Read/Write Control Signals External Bus Interface SMC CompactFlash Logic A23 1 0 1 0 0 CFOE 1 1 1 CFWE A22 NRD_NOE 0 NWR0_NWE CFIOR 1 CFIOW 1 1 Table 19-8. CompactFlash Mode Selection Mode Base Address CFOE CFWE CFIOR CFIOW Attribute Memory NRD NWR0_NWE 1 1 Common Memory I/O Mode 1 1 NRD NWR0_NWE True IDE Mode 0 1 NRD NWR0_NWE Multiplexing of CompactFlash Signals on EBI Pins Table 19-9 and Table 19-10 illustrate the multiplexing of the CompactFlash logic signals with other EBI signals on the EBI pins. The EBI pins in Table 19-9 are strictly dedicated to the CompactFlash interface as soon as the EBI_CS4A and/or EBI_CS5A bits(s) of the EBI Chip Select Assignment Register in the Chip Configuration User Interface is/are set. These pins must not be used to drive any other memory devices. The EBI pins in Table 19-10 remain shared between all memory areas when the corresponding CompactFlash interface is enabled (EBI_CS4A = 1 and/or EBI_CS5A = 1). Table 19-9. Dedicated CompactFlash Interface Multiplexing CompactFlash Signals EBI Signals Pins CS4A = 1 CS5A = 1 CS4A = 0 CS5A = 0 NCS4/CFCS0 CFCS0 NCS4 NCS5/CFCS1 CFCS1 NCS5 Table 19-10. Shared CompactFlash Interface Multiplexing Access to CompactFlash Device Access to Other EBI Devices Pins CompactFlash Signals EBI Signals NRD/CFOE CFOE NRD NWR0/NWE/CFWE CFWE NWR0/NWE NWR1/NBS1/CFIOR CFIOR NWR1/NBS1 NWR3/NBS3/CFIOW CFIOW NWR3/NBS3 A25/CFRNW CFRNW A25 172 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Application Example Figure 19-8 illustrates an example of a CompactFlash application. CFCS0 and CFRNW signals are not directly connected to the CompactFlash slot 0, but do control the direction and the output enable of the buffers between the EBI and the CompactFlash Device. The timing of the CFCS0 signal is identical to the NCS4 signal. Moreover, the CFRNW signal remains valid throughout the transfer, as does the address bus. The CompactFlash _WAIT signal is connected to the NWAIT input of the Static Memory Controller. For details on these waveforms and timings, refer to Section 20. “Static Memory Controller (SMC)”. Figure 19-8. CompactFlash Application Example EBI CompactFlash Connector D[15:0] D[15:0] DIR /OE A25/CFRNW NCS4/CFCS0 _CD1 CD (PIO) _CD2 /OE A[10:0] A[10:0] A22/REG _REG NOE/CFOE _OE NWE/CFWE _WE NWR1/CFIOR _IORD NWR3/CFIOW _IOWR CFCE1 _CE1 CFCE2 _CE2 NWAIT _WAIT SAM9M11 [DATASHEET] 173 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.2.7.7 NAND Flash Support External Bus Interfaces integrate circuitry that interfaces to NAND Flash devices. External Bus Interface The NAND Flash logic is driven by the Static Memory Controller on the NCS3 address space. Programming the EBI_CS3A field in the CCFG_EBICSA register to the appropriate value enables the NAND Flash logic. For details on this register, refer to Section 18. “Bus Matrix (MATRIX)”. Access to an external NAND Flash device is then made by accessing the address space reserved to NCS3 (i.e., between 0x4000 0000 and 0x4FFF FFFF). The NAND Flash Logic drives the read and write command signals of the SMC on the NANDOE and NANDWE signals when the NCS3 signal is active. NANDOE and NANDWE are invalidated as soon as the transfer address fails to lie in the NCS3 address space. See Figure 19-10 for more information. For details on these waveforms, refer to Section 20. “Static Memory Controller (SMC)”. Figure 19-9. NAND Flash Signal Multiplexing on EBI Pins SMC NAND Flash Logic NANDOE NCSx NANDOE NRD_NOE NANDWE NANDWE NWR0_NWE 174 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

NAND Flash Signals The address latch enable and command latch enable signals on the NAND Flash device are driven by address bits A22 and A21 of the EBI address bus. The command, address or data words on the data bus of the NAND Flash device are distinguished by using their address within the NCSx address space. The chip enable (CE) signal of the device and the ready/busy (R/B) signals are connected to PIO lines. The CE signal then remains asserted even when NCSx is not selected, preventing the device from returning to standby mode. Figure 19-10. NAND Flash Application Example D[7:0] AD[7:0] A[22:21] ALE CLE NCSx/NANDCS Not Connected EBI NAND Flash NANDOE NOE NANDWE NWE PIO CE PIO R/B SAM9M11 [DATASHEET] 175 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.2.8 Implementation Examples The following hardware configurations are given for illustration only. The user should refer to the memory manufacturer website to check current device availability. 19.2.8.1 2 x 8-bit DDR2 on EBI Figure 19-11. Hardware Configuration - 2 x 8-bit DDR2 on EBI EBI_SDA10 EBI_SDA10 Software Configuration - 2 x 8-bit DDR2 on EBI  Assign EBI_CS1 to the DDR2 controller by setting the EBI_CS1A bit in the EBI Chip Select Assignment Register located in the bus matrix memory space.  Initialize the DDR2 Controller depending on the DDR2 device and system bus frequency. The DDR2 initialization sequence is described in Section 21.4.3 “DDR2-SDRAM Initialization”. 176 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.2.8.2 16-bit LPDDR on EBI Figure 19-12. Hardware Configuration - 16-bit LPDDR on EBI Software Configuration - 16-bit LPDDR on EBI The following configuration has to be performed:  Assign EBI_CS1 to the DDR2 controller by setting the bit EBI_CS1A in the EBI Chip Select Assignment Register located in the bus matrix memory space.  Initialize the DDR2 Controller depending on the LPDDR device and system bus frequency. The LPDDR initialization sequence is described in Section 21.4.2 “Low-power DDR1-SDRAM Initialization”. SAM9M11 [DATASHEET] 177 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.2.8.3 16-bit SDRAM Figure 19-13. Hardware Configuration - 16-bit SDRAM Software Configuration - 16-bit SDRAM The following configuration has to be performed:  Assign the EBI CS1 to the SDRAM controller by setting the bit EBI_CS1A in the EBI Chip Select Assignment Register located in the bus matrix memory space.  Initialize the SDRAM Controller depending on the SDRAM device and system bus frequency. The Data Bus Width is to be programmed to 16 bits. The SDRAM initialization sequence is described in Section 21.4.1 “SDR-SDRAM Initialization”. 178 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.2.8.4 2 x 16-bit SDRAM Figure 19-14. Hardware Configuration - 2 x 16-bit SDRAM A[1..14] D[0..31] SDRAM MMNN11 MMNN22 VDR4R4D771100IOKKM AAADABCBAACDACRAWAASAA8AA63952471111DQQAKALE0134K01SESAMM1010 111122222333332234331332786934569012342060875951 AAAAAAAAAAABANCCDDCRWCAB1110123456789AAL.KQQAASEC021K01ESSMM1MMLHTT4488LLCC1166MM1166AA22VVVVVVVVDDDDDDDDDDVVSSSSVDDDDDDDDDDVVVQQQQQQDDDDSSSSDDDQQQQQQQQQQSSS111111QQQQQQQQDDDSSS0123450123456789 444555124215394461452457811144578013817443901324262 DDDDDDDDDDDDDDDD2593067814111111C1C1024531V001100DNNDC1C1FFI00O2200MNNC1C1FF003300NNC1C1FF004400NNFFC1C10055C1C10000NN6600FFNNFFC1C1007700NNFF VDDIOM DDAAAASAAAAAAAABBCCCRW34976528AA1D111QQKAALE3014K01ESSAMM1230 111122222333332234331332786934569012342060875951 AAAAAAAAAAABANCCDDCRWCAB01234567891A11ALKQQAA.SEC021K01ESSMM1MMLHTT4488LLCC1166MM1166AA22VVVVVVVVDDDDDDDDDDSSSSVVVDDDDDDDDDDVVVQQQQQQDDDDSSSSDDDQQQQQQQQQQSSS111111QQQQQQQQDDDSSS0123450123456789 444555124215394461452457811144578013817443926201324 C1C1V008800DDDDDDDDDDDDDDDDDNND2113223221221222C1C1FF3980461287576190I00O9900MNNC1C1FF00110000NNC1C1FF00110011NNFFC1C100110022NNC1C1FF00110033NNC1C1FF00110044NNFF MMTT4488LLCC1166MM1166AA22PP--7755IITT SDCS RR22 00RR 256 Mbits R4R4773300KK 256 Mbits RR44 00RR Software Configuration - 2 x 16-bit SDRAM The following configuration has to be performed:  Assign the EBI CS1 to the SDRAM controller by setting the bit EBI_CS1A in the EBI Chip Select Assignment Register located in the bus matrix memory space.  Initialize the SDRAM Controller depending on the SDRAM device and system bus frequency. The Data Bus Width is to be programmed to 32 bits. The data lines D[16..31] are multiplexed with PIO lines and thus the dedicated PIOs must be programmed in peripheral mode in the PIO controller. The SDRAM initialization sequence is described in Section 21.4.1 “SDR-SDRAM Initialization”. SAM9M11 [DATASHEET] 179 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.2.8.5 8-bit NAND Flash Figure 19-15. Hardware Configuration - 8-bit NAND Flash D[0..7] UU11 KK99FF22GG0088UU00MM CLE 16 CLE I/O0 29 D0 ALE 17 ALE I/O1 30 D1 NANDOE 8 RE I/O2 31 D2 NANDWE 18 WE I/O3 32 D3 (ANY PIO) 9 CE I/O4 41 D4 42 D5 I/O5 (ANY PIO) 7 R/B I/O6 43 D6 RR11 1100KK 44 D7 I/O7 3V3 19 WP RR22 1100KK 48 N.C 47 N.C 1 46 N.C N.C 2 45 N.C N.C 3 40 N.C N.C 4 39 N.C N.C 5 38 N.C PRE 6 35 N.C N.C 10 34 N.C N.C 11 33 N.C N.C 14 28 N.C N.C 15 N.C N.C 27 3V3 20 N.C 21 37 N.C VCC 22 12 N.C VCC 23 CC22 N.C 24 N.C 25 36 110000NNFF N.C VSS 26 13 N.C VSS CC11 2 Gb 110000NNFF TSOP48 PACKAGE Software Configuration - 8-bit NAND Flash The following configuration has to be performed:  Assign the EBI CS3 to the NAND Flash by setting the bit EBI_CS3A in the EBI Chip Select Assignment Register located in the bus matrix memory space  Reserve A21 / A22 for ALE / CLE functions. Address and Command Latches are controlled respectively by setting to 1 the address bit A21 and A22 during accesses.  Configure a PIO line as an input to manage the Ready/Busy signal.  Configure Static Memory Controller CS3 Setup, Pulse, Cycle and Mode accordingly to NAND Flash timings, the data bus width and the system bus frequency. 180 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.2.8.6 16-bit NAND Flash Figure 19-16. Hardware Configuration - 16-bit NAND Flash D[0..15] UU11 MMTT2299FF22GG1166AAAABBWWPP--EETT CLE 16 CLE I/O0 26 D0 ALE 17 ALE I/O1 28 D1 NANDOE 8 RE I/O2 30 D2 NANDWE 18 WE I/O3 32 D3 (ANY PIO) 9 CE I/O4 40 D4 42 D5 I/O5 (ANY PIO) 7 R/B I/O6 44 D6 RR11 1100KK 46 D7 I/O7 3V3 19 WP I/O8 27 D8 RR22 1100KK 29 D9 I/O9 31 D10 I/O10 1 33 D11 N.C I/O11 2 41 D12 N.C I/O12 3 43 D13 N.C I/O13 4 45 D14 N.C I/O14 5 47 D15 N.C I/O15 6 N.C 10 39 N.C N.C 11 38 N.C PRE 14 36 N.C N.C 15 3V3 N.C 20 N.C 21 37 N.C VCC 22 12 N.C VCC 23 N.C 24 48 CC22 N.C VSS 34 25 110000NNFF N.C VSS 35 13 N.C VSS CC11 2 Gb 110000NNFF TSOP48 PACKAGE Software Configuration - 16-bit NAND Flash The software configuration is the same as for an 8-bit NAND Flash except for the data bus width programmed in the SMC MODE Register. SAM9M11 [DATASHEET] 181 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.2.8.7 NOR Flash on NCS0 Figure 19-17. Hardware Configuration - NOR Flash on NCS0 D[0..15] A[1..22] UU11 A1 25 29 D0 A0 DQ0 A2 24 31 D1 A1 DQ1 A3 23 33 D2 A2 DQ2 A4 22 35 D3 A3 DQ3 A5 21 38 D4 A4 DQ4 A6 20 40 D5 A5 DQ5 A7 19 42 D6 A6 DQ6 A8 18 44 D7 A7 DQ7 A9 8 30 D8 A8 DQ8 A10 7 32 D9 A9 DQ9 A11 6 34 D10 A10 DQ10 A12 5 36 D11 A11 DQ11 A13 4 39 D12 A12 DQ12 A14 3 41 D13 A13 DQ13 A15 2 43 D14 A14 DQ14 A16 1 45 D15 A15 DQ15 A17 48 A16 A18 17 A17 A19 16 AATT4499BBVV66441166 A18 A20 15 A19 A21 10 A20 3V3 A22 9 A21 47 VCCQ 12 NRST RESET 11 NWE WE 14 WP VCC 37 CC22 3V3 13 VPP 110000NNFF 26 NCS0 CE 28 46 NRD OE VSS 27 VSS CC11 110000NNFF TSOP48 PACKAGE Software Configuration - NOR Flash on NCS0 The default configuration for the Static Memory Controller, byte select mode, 16-bit data bus, Read/Write controlled by Chip Select, allows boot on 16-bit non-volatile memory at slow clock. For another configuration, configure the Static Memory Controller CS0 Setup, Pulse, Cycle and Mode depending on Flash timings and system bus frequency. 182 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.2.8.8 CompactFlash Figure 19-18. Hardware Configuration - CompactFlash D[0..15] MEMORY & I/O MODE 3V3 MMNN11AA JJ11 A2(5A(cid:2)/N(cid:3)CC((cid:4)YFCF(cid:5) RCFP(cid:6)NC(cid:5)SIOW(cid:7)Sx)(cid:8)0(cid:7) o(cid:2)r(cid:8) CFCS1) 45DDDDDDDDDDDDDDDD1111119876542103543201 6SSNNMM7744NNAA22LLBBVVGGHHHHCCDDEEAAAABBCCFF212142134212132121213322M7M777222222222211111111114444NNAAAADDOBBBBBBBBOBBBBBBBB11LLLL1234567812345678IIEEBBRRVVVVCCCCHHHH22222222111111113333AAAAAAAAAAAAAAAA222222221234567812345678444435555EEFFGGHHAABBCCDD5656565656565656SSMMNNNN772244AAAACCCCCCCCCCCCCCCCLLFFFFFFFFFFFFFFFFVV________________CCDDDDDDDDDDDDDDDD33111111321076549822RR10543211124477KK 3V3R4R47722CKKCDD21 CCCCCCCCCCCCCCCCCCCCCCCCCCCCCFFFFFFFFFFFFFFFFFFFFFFFFFFFDD___________________________21ADDDDDDAAAAAAAAAADDDDDDDDDD1987654321011111149876532100354210 1111111112222222223344401245678901235678901789234568 DDDDDAAAAAAAAAAADDDCCDDDDDDDD1987654321034567012DD11111891012345021## GGVVNNCCDCCD 1315380 C1C1C1C1000022110000NNNNFFFF A[0..10] AAAAAAAA198734560 MMKKLLJJ56565656 MM33333333NNAAAAAAAA1112345678CC 33333333BBBBBBBB12345678 JJKKLLMM21212121 CCCCCCCCFFFFFFFF________AAAAAAAA198765430 WOIICCROOEEEEEWR21GDR 333342456479 COCIIWROOEEEEERW12G##D##R### INPCABBSCVVEDDKL##21 34449563 24 WP 3V3 JJ43 33DOIER WAIT# 42 WAIT# VVSS12## 3430 MM7744NNAA11LLDDVVCCHH3322224455 RESET 41 RESET RDY/BSY 37 RDY/BSY AC2CCC2FF/FFIRIOOWOEWREEG AAA021 NNRRPPTT56655656 44444444AAAAAAAA12345678 44444444BBBBBBBB12345678 NNPPRRTT12212121 CCCIIOOFFFWRRWO___DEEAAAREG210 NN77EE5500--77551166VVYY--2200 T3 4DIR T4 4OE 7744AALLVVCCHH3322224455 1 MMNN33AA SSNN7744AALLVVCC112255 CFCE2 2 3 CE2 4 MMNN33BB SSNN7744AALLVVCC112255 CFCE1 5 6 CE1 10 MMNN33CC SSNN7744AALLVVCC112255 (ANY PIO) CFRST 9 8 RESET 13 MMNN33DD RR33 SSNN7744AALLVVCC112255 1100KK (ANY PIO) CFIRQ 11 12 RDY/BSY 3V3 MMNN44 3V3 5 VVCCCC 1 RR44 1100KK NWAIT 4 2 WAIT# 3V3 GGNNDD 3 SSNN7744LLVVCC11GG112255--QQ11 SAM9M11 [DATASHEET] 183 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Software Configuration - CompactFlash The following configuration has to be performed:  Assign the EBI CS4 and/or EBI_CS5 to the CompactFlash Slot 0 and/or Slot 1 by setting the bit EBI_CS4A and/or EBI_CS5A in the EBI Chip Select Assignment Register located in the bus matrix memory space.  The address line A23 is to select I/O (A23 = 1) or Memory mode (A23 = 0) and the address line A22 for REG function.  A22, A23, CFRNW, CFS0, CFCS1, CFCE1 and CFCE2 signals are multiplexed with PIO lines and thus the dedicated PIOs must be programmed in peripheral mode in the PIO controller.  Configure a PIO line as an output for CFRST and two others as an input for CFIRQ and CARD DETECT functions respectively.  Configure SMC CS4 and/or SMC_CS5 (for Slot 0 or 1) Setup, Pulse, Cycle and Mode accordingly to CompactFlash timings and system bus frequency. 184 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

19.2.8.9 CompactFlash True IDE Figure 19-19. Hardware Configuration - CompactFlash True IDE D[0..15] TRUE IDE MODE 3V3 MMNN11AA JJ11 DDDDDDDDDDDDDDDD1111119876542103543201 GGCCDDHHAAAABBEEFF212134212121212121 77MM11111111112222222244NNAADOBBBBBBBBBBBBBBBB11LL1234567812345678IEBBRVVCCHH111111112222222233AAAAAAAAAAAAAAAA222212345678123456784455AABBCCDDEEFFGGHH5656565656565656 CCCCCCCCCCCCCCCCFFFFFFFFFFFFFFFF________________DDDDDDDDDDDDDDDD1111113210765498105432 3V3 CCCCCCCCCCCCCCCCCCFFFFFFFFFFFFFFFFDD________________21DDDDDDDDDDDDDDDD1111114987653210354210 1222222223344401235678901789234568 DDDDDAADDDCCDDDDDDDD1934567012DD11111891012345021## GGVVNNCCCCDD 1315380 C1C1C1C1000022110000NNNNFFFF 11 A8 A25/CFRNW H3 2DIR 12 A7 ((cid:2)A(cid:3)N((cid:4)CCY(cid:5)FF (cid:6)CPC(cid:5)SI(cid:7)SOx(cid:8)0)(cid:7) o(cid:2)r(cid:8) CFCS1) 45 6SSNNMM7744NNAA22LLBBVVHCC4332277244AAOLLEVVCCHH33222244355 SSMMNNNN772244AAAALLVVCC3322RR11124477KK R4R47722CKKCDD21 CCCFFF___AAA021 11111124567890 AAAAAAA6543210 A[0..10] MMNN11CC 3V3 44 REG# AAAAAAAA198734560 MMKKLLJJ56565656 33333333AAAAAAAA12345678 33333333BBBBBBBB12345678 JJKKLLMM21212121 CCCCCCCCFFFFFFFF________AAAAAAAA198765430 IICCOOEEWR21DR 3333245679 CACIIWOOTSSERWA01#D ##RS##EL# INPPDCDAASIACSEGKPL#### 34449635 24 IOIS16# 3V3 JJ43 33DOIER IORDY 42 IORDY VVSS12## 3430 MM7744NNAA11LLDDVVCCHH3322224455 RESET# 41 RESET# INTRQ 37 INTRQ AC2CCC2FF/FFIRIOOWOEWREEG AAA021 NNRRPPTT56655656 44444444AAAAAAAA12345678 44444444BBBBBBBB12345678 NNPPRRTT12212121 CCCIIOOFFFWRRWO___DEAAAEREG210 NN77EE5500--77551166VVYY--2200 T3 4DIR T4 4OE 7744AALLVVCCHH3322224455 1 MMNN33AA SSNN7744AALLVVCC112255 CFCE2 2 3 CE2 4 MMNN33BB SSNN7744AALLVVCC112255 CFCE1 5 6 CE1 10 MMNN33CC SSNN7744AALLVVCC112255 (ANY PIO) CFRST 9 8 RESET# 13 MMNN33DD RR33 SSNN7744AALLVVCC112255 1100KK (ANY PIO) CFIRQ 11 12 INTRQ 3V3 MMNN44 3V3 5 VVCCCC 1 RR44 1100KK NWAIT 4 2 IORDY 3V3 GGNNDD 3 SSNN7744LLVVCC11GG112255--QQ11 SAM9M11 [DATASHEET] 185 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Software Configuration - CompactFlash True IDE The following configuration has to be performed:  Assign the EBI CS4 and/or EBI_CS5 to the CompactFlash Slot 0 and/or Slot 1 by setting the bit EBI_CS4A and/or EBI_CS5A in the EBI Chip Select Assignment Register located in the bus matrix memory space.  The address line A21 is to select Alternate True IDE (A21 = 1) or True IDE (A21 = 0) modes.  A21, CFRNW, CFS0, CFCS1, CFCE1 and CFCE2 signals are multiplexed with PIO lines and thus the dedicated PIOs must be programmed in peripheral mode in the PIO controller.  Configure a PIO line as an output for CFRST and two others as an input for CFIRQ and CARD DETECT functions respectively.  Configure SMC CS4 and/or SMC_CS5 (for Slot 0 or 1) Setup, Pulse, Cycle and Mode accordingly to CompactFlash timings and system bus frequency. 19.2.9 Programmable I/O Lines Power Supplies and Drive Levels The power supply pin VDDIOM1 accepts two voltage ranges. This allows the device to reach its maximum speed either out of 1.8V or 3.3V external memories. The maximum speed is 133 MHz on the SDCK pin and #SDCK signals loaded with 10 pF. The load on data/address and control signals are 30 pF for power supply at 1.8V and 50 pF for power supply at 3.3V. The data lines frequency reaches 133 MHz in DDR2 mode. The other signals (control and address) do not go over 66 MHz. The EBI I/Os accept two drive levels, HIGH and LOW. This allows to avoid overshoots and give the best performance according to the bus load and external memories. Refer to the EBI Chip Select Assignment Register for more details. The voltage ranges and the drive level are determined by programming EBI_DRIVE field in the EBI Chip Select Assignment Register. At reset the selected default drive level is High. At reset, the selected voltage defaults to 3.3V typical and power supply pins can accept either 1.8V or 3.3V. The user must make sure to program the EBI voltage range before getting the device out of its Slow Clock Mode. 186 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20. Static Memory Controller (SMC) 20.1 Description The Static Memory Controller (SMC) generates the signals that control the access to the external memory devices or peripheral devices. It has 6 Chip Selects and a 26-bit address bus. The 32-bit data bus can be configured to interface with 8-, 16-, or 32-bit external devices. Separate read and write control signals allow for direct memory and peripheral interfacing. Read and write signal waveforms are fully parametrizable. The SMC can manage wait requests from external devices to extend the current access. The SMC is provided with an automatic slow clock mode. In slow clock mode, it switches from user-programmed waveforms to slow-rate specific waveforms on read and write signals. The SMC supports asynchronous burst read in page mode access for page size up to 32 bytes. 20.2 I/O Lines Description Table 20-1. I/O Line Description Name Description Type Active Level NCS[7:0] Static Memory Controller Chip Select Lines Output Low NRD Read Signal Output Low NWR0/NWE Write 0/Write Enable Signal Output Low A0/NBS0 Address Bit 0/Byte 0 Select Signal Output Low NWR1/NBS1 Write 1/Byte 1 Select Signal Output Low A1/NWR2/NBS2 Address Bit 1/Write 2/Byte 2 Select Signal Output Low NWR3/NBS3 Write 3/Byte 3 Select Signal Output Low A[25:2] Address Bus Output D[31:0] Data Bus I/O NWAIT External Wait Signal Input Low 20.3 Multiplexed Signals Table 20-2. Static Memory Controller (SMC) Multiplexed Signals Multiplexed Signals Related Function NWR0 NWE Byte-write or byte-select access, see “Byte Write or Byte Select Access” on page 189 A0 NBS0 8-bit or 16-/32-bit data bus, see “Data Bus Width” on page 189 NWR1 NBS1 Byte-write or byte-select access, see “Byte Write or Byte Select Access” on page 189 8-/16-bit or 32-bit data bus, see “Data Bus Width” on page 189. A1 NWR2 NBS2 Byte-write or byte-select access, see “Byte Write or Byte Select Access” on page 189 NWR3 NBS3 Byte-write or byte-select access, see “Byte Write or Byte Select Access” on page 189 SAM9M11 [DATASHEET] 187 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.4 Application Example 20.4.1 Hardware Interface Figure 20-1. SMC Connections to Static Memory Devices D0-D31 A0/NBS0 128K x 8 128K x 8 NWR0/NWE NWR1/NBS1 D0 - D7 SRAM D8-D15 SRAM A1/NWR2/NBS2 D0 - D7 D0-D7 NWR3/NBS3 CS CS A0 - A16 A2 - A18 A0 - A16 A2 - A18 NCS0 NRD NRD NCS1 OE OE NCS2 NWR0/NWE WE NWR1/NBS1 WE NCS3 NCS4 NCS5 NCS6 NCS7 128K x 8 128K x 8 SRAM SRAM D16 - D23 D24-D31 A2 - A25 D0 - D7 D0-D7 CS CS A2 - A18 A2 - A18 A0 - A16 A0 - A16 NRD NRD OE OE A1/NWR2/NBS2 WE NWR3/NBS3 WE Static Memory Controller 20.5 Product Dependencies 20.5.1 I/O Lines The pins used for interfacing the Static Memory Controller may be multiplexed with the PIO lines. The programmer must first program the PIO controller to assign the Static Memory Controller pins to their peripheral function. If I/O Lines of the SMC are not used by the application, they can be used for other purposes by the PIO Controller. 188 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.6 External Memory Mapping The SMC provides up to 26 address lines, A[25:0]. This allows each chip select line to address up to 64 Mbytes of memory. If the physical memory device connected on one chip select is smaller than 64 Mbytes, it wraps around and appears to be repeated within this space. The SMC correctly handles any valid access to the memory device within the page (see Figure 20-2). A[25:0] is only significant for 8-bit memory, A[25:1] is used for 16-bit memory, A[25:2] is used for 32-bit memory. Figure 20-2. Memory Connections for Eight External Devices NCS[0] - NCS[7] NCS7 Memory Enable NRD NCS6 Memory Enable SMC NWE NCS5 Memory Enable A[25:0] NCS4 Memory Enable D[31:0] NCS3 Memory Enable NCS2 Memory Enable NCS1 Memory Enable NCS0 Memory Enable Output Enable Write Enable A[25:0] 8 or 16 or 32 D[31:0] or D[15:0] or D[7:0] 20.7 Connection to External Devices 20.7.1 Data Bus Width A data bus width of 8, 16, or 32 bits can be selected for each chip select. This option is controlled by the field DBW in SMC_MODE (Mode Register) for the corresponding chip select. Figure 20-3 shows how to connect a 512K x 8-bit memory on NCS2. Figure 20-4 shows how to connect a 512K x 16-bit memory on NCS2. Figure 20-5 shows two 16-bit memories connected as a single 32-bit memory 20.7.2 Byte Write or Byte Select Access Each chip select with a 16-bit or 32-bit data bus can operate with one of two different types of write access: byte write or byte select access. This is controlled by the BAT field of the SMC_MODE register for the corresponding chip select. SAM9M11 [DATASHEET] 189 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 20-3. Memory Connection for an 8-bit Data Bus D[7:0] D[7:0] A[18:2] A[18:2] A0 A0 SMC A1 A1 NWE Write Enable NRD Output Enable NCS[2] Memory Enable Figure 20-4. Memory Connection for a 16-bit Data Bus D[15:0] D[15:0] A[19:2] A[18:1] A1 A[0] NBS0 Low Byte Enable SMC NBS1 High Byte Enable NWE Write Enable NRD Output Enable NCS[2] Memory Enable Figure 20-5. Memory Connection for a 32-bit Data Bus D[31:16] D[31:16] D[15:0] D[15:0] A[20:2] A[18:0] NBS0 Byte 0 Enable SMC NBS1 Byte 1 Enable NBS2 Byte 2 Enable NBS3 Byte 3 Enable NWE Write Enable NRD Output Enable NCS[2] Memory Enable 190 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.7.2.1Byte Write Access Byte write access supports one byte write signal per byte of the data bus and a single read signal. Note that the SMC does not allow boot in Byte Write Access mode.  For 16-bit devices: the SMC provides NWR0 and NWR1 write signals for respectively byte0 (lower byte) and byte1 (upper byte) of a 16-bit bus. One single read signal (NRD) is provided. Byte Write Access is used to connect 2 x 8-bit devices as a 16-bit memory.  For 32-bit devices: NWR0, NWR1, NWR2 and NWR3, are the write signals of byte0 (lower byte), byte1, byte2 and byte 3 (upper byte) respectively. One single read signal (NRD) is provided. Byte Write Access is used to connect 4 x 8-bit devices as a 32-bit memory. Byte Write option is illustrated on Figure 20-6. 20.7.2.2Byte Select Access In this mode, read/write operations can be enabled/disabled at a byte level. One byte-select line per byte of the data bus is provided. One NRD and one NWE signal control read and write.  For 16-bit devices: the SMC provides NBS0 and NBS1 selection signals for respectively byte0 (lower byte) and byte1 (upper byte) of a 16-bit bus. Byte Select Access is used to connect one 16-bit device.  For 32-bit devices: NBS0, NBS1, NBS2 and NBS3, are the selection signals of byte0 (lower byte), byte1, byte2 and byte 3 (upper byte) respectively. Byte Select Access is used to connect two 16-bit devices. Figure 20-7 shows how to connect two 16-bit devices on a 32-bit data bus in Byte Select Access mode, on NCS3 (BAT = Byte Select Access). Figure 20-6. Connection of 2 x 8-bit Devices on a 16-bit Bus: Byte Write Option D[7:0] D[7:0] D[15:8] A[24:2] A[23:1] SMC A1 A[0] NWR0 Write Enable NWR1 NRD Read Enable NCS[3] Memory Enable D[15:8] A[23:1] A[0] Write Enable Read Enable Memory Enable SAM9M11 [DATASHEET] 191 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.7.2.3Signal Multiplexing Depending on the BAT, only the write signals or the byte select signals are used. To save IOs at the external bus interface, control signals at the SMC interface are multiplexed. Table 20-3 shows signal multiplexing depending on the data bus width and the byte access type. For 32-bit devices, bits A0 and A1 are unused. For 16-bit devices, bit A0 of address is unused. When Byte Select Option is selected, NWR1 to NWR3 are unused. When Byte Write option is selected, NBS0 to NBS3 are unused. Figure 20-7. Connection of 2x16-bit Data Bus on a 32-bit Data Bus (Byte Select Option) D[15:0] D[15:0] D[31:16] A[25:2] A[23:0] NWE Write Enable NBS0 Low Byte Enable NBS1 High Byte Enable SMC NBS2 NBS3 NRD Read Enable NCS[3] Memory Enable D[31:16] A[23:0] Write Enable Low Byte Enable High Byte Enable Read Enable Memory Enable Table 20-3. SMC Multiplexed Signal Translation Signal Name 32-bit Bus 16-bit Bus 8-bit Bus Device Type 1x32-bit 2x16-bit 4 x 8-bit 1x16-bit 2 x 8-bit 1 x 8-bit Byte Access Type (BAT) Byte Select Byte Select Byte Write Byte Select Byte Write NBS0_A0 NBS0 NBS0 NBS0 A0 NWE_NWR0 NWE NWE NWR0 NWE NWR0 NWE NBS1_NWR1 NBS1 NBS1 NWR1 NBS1 NWR1 NBS2_NWR2_A1 NBS2 NBS2 NWR2 A1 A1 A1 NBS3_NWR3 NBS3 NBS3 NWR3 192 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.8 Standard Read and Write Protocols In the following sections, the byte access type is not considered. Byte select lines (NBS0 to NBS3) always have the same timing as the A address bus. NWE represents either the NWE signal in byte select access type or one of the byte write lines (NWR0 to NWR3) in byte write access type. NWR0 to NWR3 have the same timings and protocol as NWE. In the same way, NCS represents one of the NCS[0..5] chip select lines. 20.8.1 Read Waveforms The read cycle is shown on Figure 20-8. The read cycle starts with the address setting on the memory address bus, i.e.: {A[25:2], A1, A0} for 8-bit devices {A[25:2], A1} for 16-bit devices A[25:2] for 32-bit devices. Figure 20-8. Standard Read Cycle MCK A[25:2] NBS0,NBS1, NBS2,NBS3, A0, A1 NRD NCS D[31:0] NRD_SETUP NRD_PULSE NRD_HOLD NCS_RD_SETUP NCS_RD_PULSE NCS_RD_HOLD NRD_CYCLE 20.8.1.1NRD Waveform The NRD signal is characterized by a setup timing, a pulse width and a hold timing. 1. NRD_SETUP: the NRD setup time is defined as the setup of address before the NRD falling edge; 2. NRD_PULSE: the NRD pulse length is the time between NRD falling edge and NRD rising edge; 3. NRD_HOLD: the NRD hold time is defined as the hold time of address after the NRD rising edge. 20.8.1.2NCS Waveform Similarly, the NCS signal can be divided into a setup time, pulse length and hold time: 1. NCS_RD_SETUP: the NCS setup time is defined as the setup time of address before the NCS falling edge. 2. NCS_RD_PULSE: the NCS pulse length is the time between NCS falling edge and NCS rising edge; 3. NCS_RD_HOLD: the NCS hold time is defined as the hold time of address after the NCS rising edge. SAM9M11 [DATASHEET] 193 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.8.1.3Read Cycle The NRD_CYCLE time is defined as the total duration of the read cycle, i.e., from the time where address is set on the address bus to the point where address may change. The total read cycle time is equal to: NRD_CYCLE = NRD_SETUP + NRD_PULSE + NRD_HOLD = NCS_RD_SETUP + NCS_RD_PULSE + NCS_RD_HOLD All NRD and NCS timings are defined separately for each chip select as an integer number of Master Clock cycles. To ensure that the NRD and NCS timings are coherent, user must define the total read cycle instead of the hold timing. NRD_CYCLE implicitly defines the NRD hold time and NCS hold time as: NRD_HOLD = NRD_CYCLE - NRD SETUP - NRD PULSE NCS_RD_HOLD = NRD_CYCLE - NCS_RD_SETUP - NCS_RD_PULSE 20.8.1.4Null Delay Setup and Hold If null setup and hold parameters are programmed for NRD and/or NCS, NRD and NCS remain active continuously in case of consecutive read cycles in the same memory (see Figure 20-9). Figure 20-9. No Setup, No Hold On NRD and NCS Read Signals MCK A[25:2] NBS0,NBS1, NBS2,NBS3, A0, A1 NRD NCS D[31:0] NRD_PULSE NRD_PULSE NRD_PULSE NCS_RD_PULSE NCS_RD_PULSE NCS_RD_PULSE NRD_CYCLE NRD_CYCLE NRD_CYCLE 20.8.1.5Null Pulse Programming null pulse is not permitted. Pulse must be at least set to 1. A null value leads to unpredictable behavior. 194 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.8.2 Read Mode As NCS and NRD waveforms are defined independently of one other, the SMC needs to know when the read data is available on the data bus. The SMC does not compare NCS and NRD timings to know which signal rises first. The READ_MODE parameter in the SMC_MODE register of the corresponding chip select indicates which signal of NRD and NCS controls the read operation. 20.8.2.1Read is Controlled by NRD (READ_MODE = 1): Figure 20-10 shows the waveforms of a read operation of a typical asynchronous RAM. The read data is available t after the falling edge of NRD, and turns to ‘Z’ after the rising edge of NRD. In this case, the READ_MODE PACC must be set to 1 (read is controlled by NRD), to indicate that data is available with the rising edge of NRD. The SMC samples the read data internally on the rising edge of Master Clock that generates the rising edge of NRD, whatever the programmed waveform of NCS may be. Figure 20-10. READ_MODE = 1: Data is sampled by SMC before the rising edge of NRD MCK A[25:2] NBS0,NBS1, NBS2,NBS3, A0, A1 NRD NCS t PACC D[31:0] Data Sampling 20.8.2.2Read is Controlled by NCS (READ_MODE = 0) Figure 20-11 shows the typical read cycle of an LCD module. The read data is valid t after the falling edge of PACC the NCS signal and remains valid until the rising edge of NCS. Data must be sampled when NCS is raised. In that case, the READ_MODE must be set to 0 (read is controlled by NCS): the SMC internally samples the data on the rising edge of Master Clock that generates the rising edge of NCS, whatever the programmed waveform of NRD may be. SAM9M11 [DATASHEET] 195 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 20-11. READ_MODE = 0: Data is sampled by SMC before the rising edge of NCS MCK A[25:2] NBS0,NBS1, NBS2,NBS3, A0, A1 NRD NCS tPACC D[31:0] Data Sampling 196 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.8.3 Write Waveforms The write protocol is similar to the read protocol. It is depicted in Figure 20-12. The write cycle starts with the address setting on the memory address bus. 20.8.3.1NWE Waveforms The NWE signal is characterized by a setup timing, a pulse width and a hold timing. 1. NWE_SETUP: the NWE setup time is defined as the setup of address and data before the NWE falling edge; 2. NWE_PULSE: The NWE pulse length is the time between NWE falling edge and NWE rising edge; 3. NWE_HOLD: The NWE hold time is defined as the hold time of address and data after the NWE rising edge. The NWE waveforms apply to all byte-write lines in Byte Write access mode: NWR0 to NWR3. 20.8.3.2NCS Waveforms The NCS signal waveforms in write operation are not the same that those applied in read operations, but are separately defined: 1. NCS_WR_SETUP: the NCS setup time is defined as the setup time of address before the NCS falling edge. 2. NCS_WR_PULSE: the NCS pulse length is the time between NCS falling edge and NCS rising edge; 3. NCS_WR_HOLD: the NCS hold time is defined as the hold time of address after the NCS rising edge. Figure 20-12. Write Cycle MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0, A1 NWE NCS NWE_SETUP NWE_PULSE NWE_HOLD NCS_WR_SETUP NCS_WR_PULSE NCS_WR_HOLD NWE_CYCLE 20.8.3.3Write Cycle The write_cycle time is defined as the total duration of the write cycle, that is, from the time where address is set on the address bus to the point where address may change. The total write cycle time is equal to: NWE_CYCLE = NWE_SETUP + NWE_PULSE + NWE_HOLD = NCS_WR_SETUP + NCS_WR_PULSE + NCS_WR_HOLD SAM9M11 [DATASHEET] 197 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

All NWE and NCS (write) timings are defined separately for each chip select as an integer number of Master Clock cycles. To ensure that the NWE and NCS timings are coherent, the user must define the total write cycle instead of the hold timing. This implicitly defines the NWE hold time and NCS (write) hold times as: NWE_HOLD = NWE_CYCLE - NWE_SETUP - NWE_PULSE NCS_WR_HOLD = NWE_CYCLE - NCS_WR_SETUP - NCS_WR_PULSE 20.8.3.4Null Delay Setup and Hold If null setup parameters are programmed for NWE and/or NCS, NWE and/or NCS remain active continuously in case of consecutive write cycles in the same memory (see Figure 20-13). However, for devices that perform write operations on the rising edge of NWE or NCS, such as SRAM, either a setup or a hold must be programmed. Figure 20-13. Null Setup and Hold Values of NCS and NWE in Write Cycle MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0, A1 NWE, NWR0, NWR1, NWR2, NWR3 NCS D[31:0] NWE_PULSE NWE_PULSE NWE_PULSE NCS_WR_PULSE NCS_WR_PULSE NCS_WR_PULSE NWE_CYCLE NWE_CYCLE NWE_CYCLE 20.8.3.5Null Pulse Programming null pulse is not permitted. Pulse must be at least set to 1. A null value leads to unpredictable behavior. 20.8.4 Write Mode The WRITE_MODE parameter in the SMC_MODE register of the corresponding chip select indicates which signal controls the write operation. 20.8.4.1Write is Controlled by NWE (WRITE_MODE = 1): Figure 20-14 shows the waveforms of a write operation with WRITE_MODE set to 1. The data is put on the bus during the pulse and hold steps of the NWE signal. The internal data buffers are turned out after the NWE_SETUP time, and until the end of the write cycle, regardless of the programmed waveform on NCS. 198 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 20-14. WRITE_MODE = 1. The write operation is controlled by NWE MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0, A1 NWE, NWR0, NWR1, NWR2, NWR3 NCS D[31:0] 20.8.4.2Write is Controlled by NCS (WRITE_MODE = 0) Figure 20-15 shows the waveforms of a write operation with WRITE_MODE set to 0. The data is put on the bus during the pulse and hold steps of the NCS signal. The internal data buffers are turned out after the NCS_WR_SETUP time, and until the end of the write cycle, regardless of the programmed waveform on NWE. Figure 20-15. WRITE_MODE = 0. The write operation is controlled by NCS MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0, A1 NWE, NWR0, NWR1, NWR2, NWR3 NCS D[31:0] SAM9M11 [DATASHEET] 199 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.8.5 Coding Timing Parameters All timing parameters are defined for one chip select and are grouped together in one SMC_REGISTER according to their type. The SMC_SETUP register groups the definition of all setup parameters:  NRD_SETUP, NCS_RD_SETUP, NWE_SETUP, NCS_WR_SETUP The SMC_PULSE register groups the definition of all pulse parameters:  NRD_PULSE, NCS_RD_PULSE, NWE_PULSE, NCS_WR_PULSE The SMC_CYCLE register groups the definition of all cycle parameters:  NRD_CYCLE, NWE_CYCLE Table 20-4 shows how the timing parameters are coded and their permitted range. Table 20-4. Coding and Range of Timing Parameters Permitted Range Coded Value Number of Bits Effective Value Coded Value Effective Value setup [5:0] 6 128 x setup[5] + setup[4:0] 0 ≤ 31 0 ≤ 128 + 31 pulse [6:0] 7 256 x pulse[6] + pulse[5:0] 0 ≤ 63 0 ≤ 256 + 63 0 ≤ 256 + 127 cycle [8:0] 9 256 x cycle[8:7] + cycle[6:0] 0 ≤ 127 0 ≤ 512 + 127 0 ≤ 768 + 127 20.8.6 Reset Values of Timing Parameters Table 20-8 gives the default value of timing parameters at reset. 20.8.7 Usage Restriction The SMC does not check the validity of the user-programmed parameters. If the sum of SETUP and PULSE parameters is larger than the corresponding CYCLE parameter, this leads to unpredictable behavior of the SMC. For read operations: Null but positive setup and hold of address and NRD and/or NCS can not be guaranteed at the memory interface because of the propagation delay of theses signals through external logic and pads. If positive setup and hold values must be verified, then it is strictly recommended to program non-null values so as to cover possible skews between address, NCS and NRD signals. For write operations: If a null hold value is programmed on NWE, the SMC can guarantee a positive hold of address, byte select lines, and NCS signal after the rising edge of NWE. This is true for WRITE_MODE = 1 only. See “Early Read Wait State” on page 201. For read and write operations: a null value for pulse parameters is forbidden and may lead to unpredictable behavior. In read and write cycles, the setup and hold time parameters are defined in reference to the address bus. For external devices that require setup and hold time between NCS and NRD signals (read), or between NCS and NWE signals (write), these setup and hold times must be converted into setup and hold times in reference to the address bus. 200 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.9 Automatic Wait States Under certain circumstances, the SMC automatically inserts idle cycles between accesses to avoid bus contention or operation conflict. 20.9.1 Chip Select Wait States The SMC always inserts an idle cycle between two transfers on separate chip selects. This idle cycle ensures that there is no bus contention between the de-activation of one device and the activation of the next one. During chip select wait state, all control lines are turned inactive: NBS0 to NBS3, NWR0 to NWR3, NCS[0..5], NRD lines are all set to 1. Figure 20-16 illustrates a chip select wait state between access on Chip Select 0 and Chip Select 2. Figure 20-16. Chip Select Wait State between a Read Access on NCS0 and a Write Access on NCS2 MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0,A1 NRD NWE NCS0 NCS2 NRD_CYCLE NWE_CYCLE D[31:0] Read to Write Chip Select Wait State Wait State 20.9.2 Early Read Wait State In some cases, the SMC inserts a wait state cycle between a write access and a read access to allow time for the write cycle to end before the subsequent read cycle begins. This wait state is not generated in addition to a chip select wait state. The early read cycle thus only occurs between a write and read access to the same memory device (same chip select). An early read wait state is automatically inserted if at least one of the following conditions is valid:  if the write controlling signal has no hold time and the read controlling signal has no setup time (Figure 20- 17).  in NCS write controlled mode (WRITE_MODE = 0), if there is no hold timing on the NCS signal and the NCS_RD_SETUP parameter is set to 0, regardless of the read mode (Figure 20-18). The write operation must end with a NCS rising edge. Without an Early Read Wait State, the write operation could not complete properly. SAM9M11 [DATASHEET] 201 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

 in NWE controlled mode (WRITE_MODE = 1) and if there is no hold timing (NWE_HOLD = 0), the feedback of the write control signal is used to control address, data, chip select and byte select lines. If the external write control signal is not inactivated as expected due to load capacitances, an Early Read Wait State is inserted and address, data and control signals are maintained one more cycle. See Figure 20-19. Figure 20-17. Early Read Wait State: Write with No Hold Followed by Read with No Setup MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0, A1 NWE NRD no hold no setup D[31:0] write cycle Early Read read cycle wait state Figure 20-18. Early Read Wait State: NCS Controlled Write with No Hold Followed by a Read with No NCS Setup MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0,A1 NCS NRD no hold no setup D[31:0] read cycle write cycle Early Read (READ_MODE = 0 or READ_MODE = 1) (WRITE_MODE = 0) wait state 202 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 20-19. Early Read Wait State: NWE-controlled Write with No Hold Followed by a Read with one Set-up Cycle MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0, A1 internal write controlling signal external write controlling signal (NWE) no hold read setup = 1 NRD D[31:0] read cycle write cycle Early Read (READ_MODE = 0 or READ_MODE = 1) (WRITE_MODE = 1) wait state 20.9.3 Reload User Configuration Wait State The user may change any of the configuration parameters by writing the SMC user interface. When detecting that a new user configuration has been written in the user interface, the SMC inserts a wait state before starting the next access. The so called “Reload User Configuration Wait State” is used by the SMC to load the new set of parameters to apply to next accesses. The Reload Configuration Wait State is not applied in addition to the Chip Select Wait State. If accesses before and after re-programming the user interface are made to different devices (Chip Selects), then one single Chip Select Wait State is applied. On the other hand, if accesses before and after writing the user interface are made to the same device, a Reload Configuration Wait State is inserted, even if the change does not concern the current Chip Select. 20.9.3.1User Procedure To insert a Reload Configuration Wait State, the SMC detects a write access to any SMC_MODE register of the user interface. If the user only modifies timing registers (SMC_SETUP, SMC_PULSE, SMC_CYCLE registers) in the user interface, he must validate the modification by writing the SMC_MODE, even if no change was made on the mode parameters. The user must not change the configuration parameters of an SMC Chip Select (Setup, Pulse, Cycle, Mode) if accesses are performed on this CS during the modification. Any change of the Chip Select parameters, while fetching the code from a memory connected on this CS, may lead to unpredictable behavior. The instructions used to modify the parameters of an SMC Chip Select can be executed from the internal RAM or from a memory connected to another CS. SAM9M11 [DATASHEET] 203 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.9.3.2Slow Clock Mode Transition A Reload Configuration Wait State is also inserted when the Slow Clock Mode is entered or exited, after the end of the current transfer (see “Slow Clock Mode” on page 214). 20.9.4 Read to Write Wait State Due to an internal mechanism, a wait cycle is always inserted between consecutive read and write SMC accesses. This wait cycle is referred to as a read to write wait state in this document. This wait cycle is applied in addition to chip select and reload user configuration wait states when they are to be inserted. See Figure 20-16 on page 201. 20.10 Data Float Wait States Some memory devices are slow to release the external bus. For such devices, it is necessary to add wait states (data float wait states) after a read access:  Before starting a read access to a different external memory  Before starting a write access to the same device or to a different external one. The Data Float Output Time (t ) for each external memory device is programmed in the TDF_CYCLES field of the DF SMC_MODE register for the corresponding chip select. The value of TDF_CYCLES indicates the number of data float wait cycles (between 0 and 15) before the external device releases the bus, and represents the time allowed for the data output to go to high impedance after the memory is disabled. Data float wait states do not delay internal memory accesses. Hence, a single access to an external memory with long t will not slow down the execution of a program from internal memory. DF The data float wait states management depends on the READ_MODE and the TDF_MODE fields of the SMC_MODE register for the corresponding chip select. 20.10.1READ_MODE Setting the READ_MODE to 1 indicates to the SMC that the NRD signal is responsible for turning off the tri-state buffers of the external memory device. The Data Float Period then begins after the rising edge of the NRD signal and lasts TDF_CYCLES MCK cycles. When the read operation is controlled by the NCS signal (READ_MODE = 0), the TDF field gives the number of MCK cycles during which the data bus remains busy after the rising edge of NCS. Figure 20-20 illustrates the Data Float Period in NRD-controlled mode (READ_MODE = 1), assuming a data float period of 2 cycles (TDF_CYCLES = 2). Figure 20-21 shows the read operation when controlled by NCS (READ_MODE = 0) and the TDF_CYCLES parameter equals 3. 204 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 20-20. TDF Period in NRD Controlled Read Access (TDF = 2) MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0, A1 NRD NCS tpacc D[31:0] TDF = 2 clock cycles NRD controlled read operation Figure 20-21. TDF Period in NCS Controlled Read Operation (TDF = 3) MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0,A1 NRD NCS tpacc D[31:0] TDF = 3 clock cycles NCS controlled read operation SAM9M11 [DATASHEET] 205 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.10.2TDF Optimization Enabled (TDF_MODE = 1) When the TDF_MODE of the SMC_MODE register is set to 1 (TDF optimization is enabled), the SMC takes advantage of the setup period of the next access to optimize the number of wait states cycle to insert. Figure 20-22 shows a read access controlled by NRD, followed by a write access controlled by NWE, on Chip Select 0. Chip Select 0 has been programmed with: NRD_HOLD = 4; READ_MODE = 1 (NRD controlled) NWE_SETUP = 3; WRITE_MODE = 1 (NWE controlled) TDF_CYCLES = 6; TDF_MODE = 1 (optimization enabled). Figure 20-22. TDF Optimization: No TDF wait states are inserted if the TDF period is over when the next access begins MCK A[25:2] NRD NRD_HOLD= 4 NWE NWE_SETUP= 3 NCS0 TDF_CYCLES = 6 D[31:0] read access on NCS0 (NRD controlled) Read to Write write access on NCS0 (NWE controlled) Wait State 20.10.3TDF Optimization Disabled (TDF_MODE = 0) When optimization is disabled, tdf wait states are inserted at the end of the read transfer, so that the data float period is ended when the second access begins. If the hold period of the read1 controlling signal overlaps the data float period, no additional tdf wait states will be inserted. Figure 20-23, Figure 20-24 and Figure 20-25 illustrate the cases:  Read access followed by a read access on another chip select,  Read access followed by a write access on another chip select,  Read access followed by a write access on the same chip select, with no TDF optimization. 206 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 20-23. TDF Optimization Disabled (TDF_MODE = 0). TDF wait states between 2 read accesses on different chip selects MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0, A1 read1 controlling signal (NRD) read1 hold = 1 read2 setup = 1 read2 controlling signal (NRD) TDF_CYCLES = 6 D[31:0] 5 TDF WAIT STATES read1 cycle read 2 cycle TDF_CYCLES = 6 TDF_MODE = 0 (optimization disabled) Chip Select Wait State Figure 20-24. TDF_MODE = 0: TDF wait states between a read and a write access on different chip selects MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0, A1 read1 controlling signal (NRD) read1 hold = 1 write2 setup = 1 write2 controlling signal (NWE) TDF_CYCLES = 4 D[31:0] read1 cycle 2 TDF WAIT STATES write2 cycle TDF_CYCLES = 4 TDF_MODE = 0 Read to Write Chip Select (optimization disabled) Wait State Wait State SAM9M11 [DATASHEET] 207 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 20-25. TDF_MODE = 0: TDF wait states between read and write accesses on the same chip select MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0, A1 read1 controlling signal (NRD) read1 hold = 1 write2 setup = 1 write2 controlling signal (NWE) TDF_CYCLES = 5 D[31:0] 4 TDF WAIT STATES read1 cycle TDF_CYCLES = 5 write2 cycle Read to Write Wait State TDF_MODE = 0 (optimization disabled) 20.11 External Wait Any access can be extended by an external device using the NWAIT input signal of the SMC. The EXNW_MODE field of the SMC_MODE register on the corresponding chip select must be set to either to “10” (frozen mode) or “11” (ready mode). When the EXNW_MODE is set to “00” (disabled), the NWAIT signal is simply ignored on the corresponding chip select. The NWAIT signal delays the read or write operation in regards to the read or write controlling signal, depending on the read and write modes of the corresponding chip select. 20.11.1 Restriction When one of the EXNW_MODE is enabled, it is mandatory to program at least one hold cycle for the read/write controlling signal. For that reason, the NWAIT signal cannot be used in Page Mode (“Asynchronous Page Mode” on page 216), or in Slow Clock Mode (“Slow Clock Mode” on page 214). The NWAIT signal is assumed to be a response of the external device to the read/write request of the SMC. Then NWAIT is examined by the SMC only in the pulse state of the read or write controlling signal. The assertion of the NWAIT signal outside the expected period has no impact on SMC behavior. 208 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.11.2 Frozen Mode When the external device asserts the NWAIT signal (active low), and after internal synchronization of this signal, the SMC state is frozen, i.e., SMC internal counters are frozen, and all control signals remain unchanged. When the resynchronized NWAIT signal is deasserted, the SMC completes the access, resuming the access from the point where it was stopped. See Figure 20-26. This mode must be selected when the external device uses the NWAIT signal to delay the access and to freeze the SMC. The assertion of the NWAIT signal outside the expected period is ignored as illustrated in Figure 20-27. Figure 20-26. Write Access with NWAIT Assertion in Frozen Mode (EXNW_MODE = 10) MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0,A1 FROZEN STATE 4 3 2 1 1 1 1 0 NWE 6 5 4 3 2 2 2 2 1 0 NCS D[31:0] NWAIT internally synchronized NWAIT signal Write cycle EXNW_MODE = 10 (Frozen) WRITE_MODE = 1 (NWE_controlled) NWE_PULSE = 5 NCS_WR_PULSE = 7 SAM9M11 [DATASHEET] 209 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 20-27. Read Access with NWAIT Assertion in Frozen Mode (EXNW_MODE = 10) MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0,A1 FROZEN STATE 4 3 2 2 2 1 0 NCS 2 1 0 1 0 NRD 5 5 5 4 3 2 1 0 NWAIT internally synchronized NWAIT signal Read cycle EXNW_MODE = 10 (Frozen) READ_MODE = 0 (NCS_controlled) Assertion is ignored NRD_PULSE = 2, NRD_HOLD = 6 NCS_RD_PULSE =5, NCS_RD_HOLD =3 210 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.11.3 Ready Mode In Ready mode (EXNW_MODE = 11), the SMC behaves differently. Normally, the SMC begins the access by down counting the setup and pulse counters of the read/write controlling signal. In the last cycle of the pulse phase, the resynchronized NWAIT signal is examined. If asserted, the SMC suspends the access as shown in Figure 20-28 and Figure 20-29. After deassertion, the access is completed: the hold step of the access is performed. This mode must be selected when the external device uses deassertion of the NWAIT signal to indicate its ability to complete the read or write operation. If the NWAIT signal is deasserted before the end of the pulse, or asserted after the end of the pulse of the controlling read/write signal, it has no impact on the access length as shown in Figure 20-29. Figure 20-28. NWAIT Assertion in Write Access: Ready Mode (EXNW_MODE = 11) MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0,A1 Wait STATE 4 3 2 1 0 0 0 NWE 6 5 4 3 2 1 1 1 0 NCS D[31:0] NWAIT internally synchronized NWAIT signal Write cycle EXNW_MODE = 11 (Ready mode) WRITE_MODE = 1 (NWE_controlled) NWE_PULSE = 5 NCS_WR_PULSE = 7 SAM9M11 [DATASHEET] 211 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 20-29. NWAIT Assertion in Read Access: Ready Mode (EXNW_MODE = 11) MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0,A1 Wait STATE 6 5 4 3 2 1 0 0 NCS 6 5 4 3 2 1 1 0 NRD NWAIT internally synchronized NWAIT signal Read cycle EXNW_MODE = 11(Ready mode) READ_MODE = 0 (NCS_controlled) Assertion is ignored Assertion is ignored NRD_PULSE = 7 NCS_RD_PULSE =7 212 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.11.4 NWAIT Latency and Read/Write Timings There may be a latency between the assertion of the read/write controlling signal and the assertion of the NWAIT signal by the device. The programmed pulse length of the read/write controlling signal must be at least equal to this latency plus the 2 cycles of resynchronization + 1 cycle. Otherwise, the SMC may enter the hold state of the access without detecting the NWAIT signal assertion. This is true in frozen mode as well as in ready mode. This is illustrated on Figure 20-30. When EXNW_MODE is enabled (ready or frozen), the user must program a pulse length of the read and write controlling signal of at least: minimal pulse length = NWAIT latency + 2 resynchronization cycles + 1 cycle Figure 20-30. NWAIT Latency MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0,A1 WAIT STATE 4 3 2 1 0 0 0 NRD minimal pulse length NWAIT intenally synchronized NWAIT latency 2 cycle resynchronization NWAIT signal Read cycle EXNW_MODE = 10 or 11 READ_MODE = 1 (NRD_controlled) NRD_PULSE = 5 SAM9M11 [DATASHEET] 213 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.12 Slow Clock Mode The SMC is able to automatically apply a set of “slow clock mode” read/write waveforms when an internal signal driven by the Power Management Controller is asserted because MCK has been turned to a very slow clock rate (typically 32 kHz clock rate). In this mode, the user-programmed waveforms are ignored and the slow clock mode waveforms are applied. This mode is provided so as to avoid reprogramming the User Interface with appropriate waveforms at very slow clock rate. When activated, the slow mode is active on all chip selects. 20.12.1Slow Clock Mode Waveforms Figure 20-31 illustrates the read and write operations in slow clock mode. They are valid on all chip selects. Table 20-5 indicates the value of read and write parameters in slow clock mode. Figure 20-31. Read/Write Cycles in Slow Clock Mode MCK MCK A[25:2] A[25:2] NBS0, NBS1, NBS0, NBS1, NBS2, NBS3, NBS2, NBS3, A0,A1 A0,A1 NRD NWE 1 1 1 1 1 NCS NCS NRD_CYCLE = 2 NWE_CYCLE = 3 SLOW CLOCK MODE WRITE SLOW CLOCK MODE READ Table 20-5. Read and Write Timing Parameters in Slow Clock Mode Read Parameters Duration (cycles) Write Parameters Duration (cycles) NRD_SETUP 1 NWE_SETUP 1 NRD_PULSE 1 NWE_PULSE 1 NCS_RD_SETUP 0 NCS_WR_SETUP 0 NCS_RD_PULSE 2 NCS_WR_PULSE 3 NRD_CYCLE 2 NWE_CYCLE 3 20.12.2Switching from (to) Slow Clock Mode to (from) Normal Mode When switching from slow clock mode to the normal mode, the current slow clock mode transfer is completed at high clock rate, with the set of slow clock mode parameters.See Figure 20-32. The external device may not be fast enough to support such timings. Figure 20-33 illustrates the recommended procedure to properly switch from one mode to the other. 214 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 20-32. Clock Rate Transition Occurs while the SMC is Performing a Write Operation Slow Clock Mode internal signal from PMC MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0,A1 NWE 1 1 1 1 1 1 2 3 2 NCS NWE_CYCLE = 3 NWE_CYCLE = 7 SLOW CLOCK MODE WRITE SLOW CLOCK MODE WRITE NORMAL MODE WRITE This write cycle finishes with the slow clock mode set Slow clock mode transition is detected: of parameters after the clock rate transition Reload Configuration Wait State Figure 20-33. Recommended Procedure to Switch from Slow Clock Mode to Normal Mode or from Normal Mode to Slow Clock Mode Slow Clock Mode internal signal from PMC MCK A[25:2] NBS0, NBS1, NBS2, NBS3, A0,A1 NWE 1 1 1 2 3 2 NCS SLOW CLOCK MODE WRITE IDLE STATE NORMAL MODE WRITE Reload Configuration Wait State SAM9M11 [DATASHEET] 215 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.13 Asynchronous Page Mode The SMC supports asynchronous burst reads in page mode, providing that the page mode is enabled in the SMC_MODE register (PMEN field). The page size must be configured in the SMC_MODE register (PS field) to 4, 8, 16 or 32 bytes. The page defines a set of consecutive bytes into memory. A 4-byte page (resp. 8-, 16-, 32-byte page) is always aligned to 4-byte boundaries (resp. 8-, 16-, 32-byte boundaries) of memory. The MSB of data address defines the address of the page in memory, the LSB of address define the address of the data in the page as detailed in Table 20-6. With page mode memory devices, the first access to one page (t ) takes longer than the subsequent accesses to pa the page (t ) as shown in Figure 20-34. When in page mode, the SMC enables the user to define different read sa timings for the first access within one page, and next accesses within the page. Table 20-6. Page Address and Data Address within a Page Page Size Page Address(1) Data Address in the Page(2) 4 bytes A[25:2] A[1:0] 8 bytes A[25:3] A[2:0] 16 bytes A[25:4] A[3:0] 32 bytes A[25:5] A[4:0] Notes: 1. A denotes the address bus of the memory device 2. For 16-bit devices, the bit 0 of address is ignored. For 32-bit devices, bits [1:0] are ignored. 20.13.1Protocol and Timings in Page Mode Figure 20-34 shows the NRD and NCS timings in page mode access. Figure 20-34. Page Mode Read Protocol (Address MSB and LSB are defined in Table 20-6) MCK A[MSB] A[LSB] NRD NCS tpa tsa tsa D[31:0] NCS_RD_PULSE NRD_PULSE NRD_PULSE The NRD and NCS signals are held low during all read transfers, whatever the programmed values of the setup and hold timings in the User Interface may be. Moreover, the NRD and NCS timings are identical. The pulse length of the first access to the page is defined with the NCS_RD_PULSE field of the SMC_PULSE register. The pulse length of subsequent accesses within the page are defined using the NRD_PULSE parameter. 216 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The programming of the read timings in page mode is described in Table 20-7. Table 20-7. Programming of Read Timings in Page Mode Parameter Value Definition READ_MODE ‘x’ No impact NCS_RD_SETUP ‘x’ No impact NCS_RD_PULSE t Access time of first access to the page pa NRD_SETUP ‘x’ No impact NRD_PULSE t Access time of subsequent accesses in the page sa NRD_CYCLE ‘x’ No impact The SMC does not check the coherency of timings. It will always apply the NCS_RD_PULSE timings as page access timing (t ) and the NRD_PULSE for accesses to the page (t ), even if the programmed value for t is pa sa pa shorter than the programmed value for t . sa 20.13.2Byte Access Type in Page Mode The Byte Access Type configuration remains active in page mode. For 16-bit or 32-bit page mode devices that require byte selection signals, configure the BAT field of the SMC_REGISTER to 0 (byte select access type). 20.13.3Page Mode Restriction The page mode is not compatible with the use of the NWAIT signal. Using the page mode and the NWAIT signal may lead to unpredictable behavior. 20.13.4Sequential and Non-sequential Accesses If the chip select and the MSB of addresses as defined in Table 20-6 are identical, then the current access lies in the same page as the previous one, and no page break occurs. Using this information, all data within the same page, sequential or not sequential, are accessed with a minimum access time (t ). Figure 20-35 illustrates access to an 8-bit memory device in page mode, with 8-byte pages. sa Access to D1 causes a page access with a long access time (t ). Accesses to D3 and D7, though they are not pa sequential accesses, only require a short access time (t ). sa If the MSB of addresses are different, the SMC performs the access of a new page. In the same way, if the chip select is different from the previous access, a page break occurs. If two sequential accesses are made to the page mode memory, but separated by an other internal or external peripheral access, a page break occurs on the second access because the chip select of the device was deasserted between both accesses. SAM9M11 [DATASHEET] 217 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 20-35. Access to Non-sequential Data within the Same Page MCK A[25:3] Page address A[2], A1, A0 A1 A3 A7 NRD NCS D[7:0] D1 D3 D7 NCS_RD_PULSE NRD_PULSE NRD_PULSE 218 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.14 Programmable IO Delays The external bus interface consists of a data bus, an address bus and control signals. The simultaneous switching outputs on these busses may lead to a peak of current in the internal and external power supply lines. In order to reduce the peak of current in such cases, additional propagation delays can be adjusted independently for pad buffers by means of configuration registers, SMC_DELAY1-8. The additional programmable delays for each IO range from 0 to 4 ns (Worst Case PVT). The delay can differ between IOs supporting this feature. Delay can be modified per programming for each IO. The minimal additional delay that can be programmed on a PAD suppporting this feature is 1/16 of the maximum programmable delay. When programming 0x0 in fields “Delay1 to Delay 8”, no delay is added (reset value) and the propagation delay of the pad buffers is the inherent delay of the pad buffer. When programming 0xF in field “Delay1” the propagation delay of the corresponding pad is maximal. SMC_DELAY1, SMC_DELAY2 allow to configure delay on D[15:0], SMC_DELAY1[3:0] corresponds to D[0] and SMC_DELAY2[3:0] corresponds to D[8]. SMC_DELAY3, SMC_DELAY4 allow to configure delay on D[31:16], SMC_DELAY3[3:0] corresponds to D[16] and SMC_DELAY4[3:0] corresponds to D[24]. In case of multiplexing through the PIO controller, refer to the alternate function of D[31:16]. SMC_DELAY5, 6, 7 and 8 allow to configure delay on A[25:0], SMC_DELAY5[3:0] corresponds to A[0]. In case of multiplexing through the PIO controller, refer to the alternate function of A[25:0]. Figure 20-36. Programmable IO Delays D_in[0] SMC D_out[0] Programmable Delay Line D[0] DELAY1 D_in[1] D_out[1] Programmable Delay Line D[1] DELAY2 PIO D_in[n] D_out[n] Programmable Delay Line D[n] DELAYx PIO A[m] Programmable Delay Line A[m] DELAYy SAM9M11 [DATASHEET] 219 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.15 Static Memory Controller (SMC) User Interface The SMC is programmed using the registers listed in Table 20-8. For each chip select, a set of 4 registers is used to pro- gram the parameters of the external device connected on it. In Table 20-8, “CS_number” denotes the chip select number. 16 bytes (0x10) are required per chip select. The user must complete writing the configuration by writing any one of the SMC_MODE registers. Table 20-8. Register Mapping Offset Register Name Access Reset 0x10 x CS_number + 0x00 SMC Setup Register SMC_SETUP Read/Write 0x01010101 0x10 x CS_number + 0x04 SMC Pulse Register SMC_PULSE Read/Write 0x01010101 0x10 x CS_number + 0x08 SMC Cycle Register SMC_CYCLE Read/Write 0x00030003 0x10 x CS_number + 0x0C SMC Mode Register SMC_MODE Read/Write 0x10001000 0xC0 SMC Delay on I/O SMC_DELAY1 Read/Write 0x00000000 0xC4 SMC Delay on I/O SMC_DELAY2 Read/Write 0x00000000 0xC8 SMC Delay on I/O SMC_DELAY3 Read/Write 0x00000000 0xCC SMC Delay on I/O SMC_DELAY4 Read/Write 0x00000000 0xD0 SMC Delay on I/O SMC_DELAY5 Read/Write 0x00000000 0xD4 SMC Delay on I/O SMC_DELAY6 Read/Write 0x00000000 0xD8 SMC Delay on I/O SMC_DELAY7 Read/Write 0x00000000 0xDC SMC Delay on I/O SMC_DELAY8 Read/Write 0x00000000 0xEC-0xFC Reserved - - - 220 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.15.1SMC Setup Register Name: SMC_SETUP[0..5] Address: 0xFFFFE800 [0], 0xFFFFE810 [1], 0xFFFFE820 [2], 0xFFFFE830 [3], 0xFFFFE840 [4], 0xFFFFE850 [5] Access: Read/Write 31 30 29 28 27 26 25 24 – – NCS_RD_SETUP 23 22 21 20 19 18 17 16 – – NRD_SETUP 15 14 13 12 11 10 9 8 – – NCS_WR_SETUP 7 6 5 4 3 2 1 0 – – NWE_SETUP • NWE_SETUP: NWE Setup Length The NWE signal setup length is defined as: NWE setup length = (128 * NWE_SETUP[5] + NWE_SETUP[4:0]) clock cycles • NCS_WR_SETUP: NCS Setup Length in WRITE Access In write access, the NCS signal setup length is defined as: NCS setup length = (128 * NCS_WR_SETUP[5] + NCS_WR_SETUP[4:0]) clock cycles • NRD_SETUP: NRD Setup Length The NRD signal setup length is defined in clock cycles as: NRD setup length = (128 * NRD_SETUP[5] + NRD_SETUP[4:0]) clock cycles • NCS_RD_SETUP: NCS Setup Length in READ Access In read access, the NCS signal setup length is defined as: NCS setup length = (128 * NCS_RD_SETUP[5] + NCS_RD_SETUP[4:0]) clock cycles SAM9M11 [DATASHEET] 221 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.15.2SMC Pulse Register Name: SMC_PULSE[0..5] Address: 0xFFFFE804 [0], 0xFFFFE814 [1], 0xFFFFE824 [2], 0xFFFFE834 [3], 0xFFFFE844 [4], 0xFFFFE854 [5] Access: Read/Write 31 30 29 28 27 26 25 24 – NCS_RD_PULSE 23 22 21 20 19 18 17 16 – NRD_PULSE 15 14 13 12 11 10 9 8 – NCS_WR_PULSE 7 6 5 4 3 2 1 0 – NWE_PULSE • NWE_PULSE: NWE Pulse Length The NWE signal pulse length is defined as: NWE pulse length = (256 * NWE_PULSE[6] + NWE_PULSE[5:0]) clock cycles The NWE pulse length must be at least 1 clock cycle. • NCS_WR_PULSE: NCS Pulse Length in WRITE Access In write access, the NCS signal pulse length is defined as: NCS pulse length = (256 * NCS_WR_PULSE[6] + NCS_WR_PULSE[5:0]) clock cycles The NCS pulse length must be at least 1 clock cycle. • NRD_PULSE: NRD Pulse Length In standard read access, the NRD signal pulse length is defined in clock cycles as: NRD pulse length = (256 * NRD_PULSE[6] + NRD_PULSE[5:0]) clock cycles The NRD pulse length must be at least 1 clock cycle. In page mode read access, the NRD_PULSE parameter defines the duration of the subsequent accesses in the page. • NCS_RD_PULSE: NCS Pulse Length in READ Access In standard read access, the NCS signal pulse length is defined as: NCS pulse length = (256 * NCS_RD_PULSE[6] + NCS_RD_PULSE[5:0]) clock cycles The NCS pulse length must be at least 1 clock cycle. In page mode read access, the NCS_RD_PULSE parameter defines the duration of the first access to one page. 222 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.15.3SMC Cycle Register Name: SMC_CYCLE[0..5] Address: 0xFFFFE808 [0], 0xFFFFE818 [1], 0xFFFFE828 [2], 0xFFFFE838 [3], 0xFFFFE848 [4], 0xFFFFE858 [5] Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – NRD_CYCLE 23 22 21 20 19 18 17 16 NRD_CYCLE 15 14 13 12 11 10 9 8 – – – – – – – NWE_CYCLE 7 6 5 4 3 2 1 0 NWE_CYCLE • NWE_CYCLE: Total Write Cycle Length The total write cycle length is the total duration in clock cycles of the write cycle. It is equal to the sum of the setup, pulse and hold steps of the NWE and NCS signals. It is defined as: Write cycle length = (NWE_CYCLE[8:7] * 256 + NWE_CYCLE[6:0]) clock cycles • NRD_CYCLE: Total Read Cycle Length The total read cycle length is the total duration in clock cycles of the read cycle. It is equal to the sum of the setup, pulse and hold steps of the NRD and NCS signals. It is defined as: Read cycle length = (NRD_CYCLE[8:7] * 256 + NRD_CYCLE[6:0]) clock cycles SAM9M11 [DATASHEET] 223 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.15.4SMC MODE Register Name: SMC_MODE[0..5] Address: 0xFFFFE80C [0], 0xFFFFE81C [1], 0xFFFFE82C [2], 0xFFFFE83C [3], 0xFFFFE84C [4], 0xFFFFE85C [5] Access: Read/Write 31 30 29 28 27 26 25 24 – – PS – – – PMEN 23 22 21 20 19 18 17 16 – – – TDF_MODE TDF_CYCLES 15 14 13 12 11 10 9 8 – – DBW – – – BAT 7 6 5 4 3 2 1 0 – – EXNW_MODE – – WRITE_MODE READ_MODE • READ_MODE: 1: The read operation is controlled by the NRD signal. – If TDF cycles are programmed, the external bus is marked busy after the rising edge of NRD. – If TDF optimization is enabled (TDF_MODE =1), TDF wait states are inserted after the setup of NRD. 0: The read operation is controlled by the NCS signal. – If TDF cycles are programmed, the external bus is marked busy after the rising edge of NCS. – If TDF optimization is enabled (TDF_MODE =1), TDF wait states are inserted after the setup of NCS. • WRITE_MODE 1: The write operation is controlled by the NWE signal. – If TDF optimization is enabled (TDF_MODE =1), TDF wait states will be inserted after the setup of NWE. 0: The write operation is controlled by the NCS signal. – If TDF optimization is enabled (TDF_MODE =1), TDF wait states will be inserted after the setup of NCS. • EXNW_MODE: NWAIT Mode The NWAIT signal is used to extend the current read or write signal. It is only taken into account during the pulse phase of the read and write controlling signal. When the use of NWAIT is enabled, at least one cycle hold duration must be pro- grammed for the read and write controlling signal. EXNW_MODE NWAIT Mode 0 0 Disabled 0 1 Reserved 1 0 Frozen Mode 1 1 Ready Mode • Disabled Mode: The NWAIT input signal is ignored on the corresponding Chip Select. • Frozen Mode: If asserted, the NWAIT signal freezes the current read or write cycle. After deassertion, the read/write cycle is resumed from the point where it was stopped. • Ready Mode: The NWAIT signal indicates the availability of the external device at the end of the pulse of the controlling read or write signal, to complete the access. If high, the access normally completes. If low, the access is extended until NWAIT returns high. 224 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• BAT: Byte Access Type This field is used only if DBW defines a 16- or 32-bit data bus. • 1: Byte write access type: – Write operation is controlled using NCS, NWR0, NWR1, NWR2, NWR3. – Read operation is controlled using NCS and NRD. • 0: Byte select access type: – Write operation is controlled using NCS, NWE, NBS0, NBS1, NBS2 and NBS3 – Read operation is controlled using NCS, NRD, NBS0, NBS1, NBS2 and NBS3 • DBW: Data Bus Width DBW Data Bus Width 0 0 8-bit bus 0 1 16-bit bus 1 0 32-bit bus 1 1 Reserved • TDF_CYCLES: Data Float Time This field gives the integer number of clock cycles required by the external device to release the data after the rising edge of the read controlling signal. The SMC always provide one full cycle of bus turnaround after the TDF_CYCLES period. The external bus cannot be used by another chip select during TDF_CYCLES + 1 cycles. From 0 up to 15 TDF_CYCLES can be set. • TDF_MODE: TDF Optimization 1: TDF optimization is enabled. – The number of TDF wait states is optimized using the setup period of the next read/write access. 0: TDF optimization is disabled. – The number of TDF wait states is inserted before the next access begins. • PMEN: Page Mode Enabled 1: Asynchronous burst read in page mode is applied on the corresponding chip select. 0: Standard read is applied. • PS: Page Size If page mode is enabled, this field indicates the size of the page in bytes. PS Page Size 0 0 4-byte page 0 1 8-byte page 1 0 16-byte page 1 1 32-byte page SAM9M11 [DATASHEET] 225 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

20.15.5SMC DELAY I/O Register Name: SMC_DELAY 1-8 Address: 0xFFFFE8C0 [1], 0xFFFFE8C4 [2], 0xFFFFE8C8 [3], 0xFFFFE8CC [4], 0xFFFFE8D0 [5], 0xFFFFE8D4 [6], 0xFFFFE8D8 [7], 0xFFFFE8DC [8] Access: Read/Write 31 30 29 28 27 26 25 24 Delay8 Delay7 23 22 21 20 19 18 17 16 Delay6 Delay5 15 14 13 12 11 10 9 8 Delay4 Delay3 7 6 5 4 3 2 1 0 Delay2 Delay1 • Delay x Gives the number of elements in the delay line. 226 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21. DDR SDR SDRAM Controller (DDRSDRC) 21.1 Description The DDR SDR SDRAM Controller (DDRSDRC) is a multiport memory controller. It comprises four slave AHB interfaces. All simultaneous accesses (four independent AHB ports) are interleaved to maximize memory bandwidth and minimize transaction latency due to SDRAM protocol. The DDRSDRC extends the memory capabilities of a chip by providing the interface to an external 16-bit or 32-bit SDR-SDRAM device and external 16-bit DDR-SDRAM device. The page size supports ranges from 2048 to 16384 and the number of columns from 256 to 4096. It supports byte (8-bit), half-word (16-bit) and word (32-bit) accesses. The DDRSDRC supports a read or write burst length of eight locations which frees the command and address bus to anticipate the next command, thus reducing latency imposed by the SDRAM protocol and improving the SDRAM bandwidth. Moreover it keeps track of the active row in each bank, thus maximizing SDRAM performance, e.g., the application may be placed in one bank and data in the other banks. So as to optimize performance, it is advisable to avoid accessing different rows in the same bank. The DDRSDRC supports a CAS latency of 2 or 3 and optimizes the read access depending on the frequency. The features of self refresh, power-down and deep power-down modes minimize the consumption of the SDRAM device. The DDRSDRC user interface is compliant with ARM Advanced Peripheral Bus (APB rev2). Note: The term “SDRAM device” regroups SDR-SDRAM, Low-power SDR-SDRAM, Low-power DDR1-SDRAM and DDR2-SDRAM devices. SAM9M11 [DATASHEET] 227 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.2 Embedded Characteristics  AMBA Compliant Interface, interfaces Directly to the ARM Advanced High performance Bus (AHB) ̶ Four AHB Interfaces, Management of All Accesses Maximizes Memory Bandwidth and Minimizes Transaction Latency ̶ AHB Transfer: Word, Half Word, Byte Access  Supports DDR2-SDRAM, Low-power DDR1-SDRAM or DDR2-SDRAM, SDR-SDRAM and Low-power SDR-SDRAM  Numerous Configurations Supported ̶ 2K, 4K, 8K, 16K Row Address Memory Parts ̶ SDRAM with Four Internal Banks ̶ SDR-SDRAM with 16- or 32-bit Data Path ̶ DDR-SDRAM with 16-bit Data Path ̶ One Chip Select for SDRAM Device (256 Mbyte Address Space)  Programming Facilities ̶ Multibank Ping-pong Access (Up to or 4 Banks Opened at Same Time = Reduces Average Latency of Transactions) ̶ Timing Parameters Specified by Software ̶ Automatic Refresh Operation, Refresh Rate is Programmable ̶ Automatic Update of DS, TCR and PASR Parameters (Low-power SDRAM Devices)  Energy-saving Capabilities ̶ Self-refresh, Power-down, Active Power-down and Deep Power-down Modes Supported  SDRAM Power-up Initialization by Software  CAS Latency of 2, 3 Supported  Reset Function Supported (DDR2-SDRAM)  ODT (On-die Termination) Not Supported  Auto Precharge Command Not Used  SDR-SDRAM with 16-bit Datapath and Eight Columns Not Supported  DDR2-SDRAM with Eight Internal Banks Not Supported  SDR-SDRAM or Low-power DDR1-SDRAM with 2 Internal Banks Not Supported  Clock Frequency Change in Precharge Power-down Mode Not Supported  OCD (Off-chip Driver) Mode Not Supported 228 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.3 DDRSDRC Module Diagram Figure 21-1. DDRSDRC Module Diagram DDR-SDR Controller AHB Slave Interface 0 Input Stage Power Management CLK/NCLK AHB Slave Interface 1 Input RAS, CAS, Stage WE, CKE Output Memory Controller Addr, DQM Stage Finite State Machine DDR-SDR SDRAM Signal Management Devices DQS AHB Slave Interface 2 Input Arbiter Stage Data ODT Asynchronous Timing AHB Slave Interface 3 Input Refresh Management Stage Interconnect Matrix APB Interface APB DDRSDRC is partitioned in two blocks (see Figure 21-1):  An Interconnect-Matrix that manages concurrent accesses on the AHB bus between four AHB masters and integrates an arbiter.  A controller that translates AHB requests (Read/Write) in the SDRAM protocol. SAM9M11 [DATASHEET] 229 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.4 Initialization Sequence The addresses given are for example purposes only. The real address depends on implementation in the product. 21.4.1 SDR-SDRAM Initialization The initialization sequence is generated by software. The SDR-SDRAM devices are initialized by the following sequence: 1. Program the memory device type into the Memory Device Register (see Section 21.8.8 on page 267). 2. Program the features of the SDR-SDRAM device into the Timing Register (asynchronous timing (trc, tras, etc.)), and into the Configuration Register (number of columns, rows, CAS latency) (see Section 21.8.3 on page 258, Section 21.8.4 on page 261 and Section 21.8.5 on page 263). 3. For low-power SDRAM, temperature-compensated self refresh (TCSR), drive strength (DS) and partial array self refresh (PASR) must be set in the Low-power Register (see Section 21.8.7 on page 265). Note: A minimum pause of 200 µs must be respected to precede any signal toggle. 4. A NOP command is issued to the SDR-SDRAM. Program NOP command into Mode Register, the application must configure the MODE field value to 1 in the Mode Register (See Section 21.8.1 on page 256). Perform a write access to any SDR-SDRAM address to acknowledge this command. Now the clock which drives SDR-SDRAM device is enabled. 5. An all banks precharge command is issued to the SDR-SDRAM. Program all banks precharge command into Mode Register, the application must configure the MODE field value to 2 in the Mode Register (See Section 21.8.1 on page 256). Perform a write access to any SDR-SDRAM address to acknowledge this command. 6. Eight auto-refresh (CBR) cycles are provided. Program the auto refresh command (CBR) into Mode Register, the application must configure the MODE field value to 4 in the Mode Register (see Section 21.8.1 on page 256).Performs a write access to any SDR-SDRAM location eight times to acknowledge these commands. 7. A Mode Register set (MRS) cycle is issued to program the parameters of the SDR-SDRAM devices, in particular CAS latency and burst length. The application must configure the MODE field value to 3 in the Mode Register (see Section 21.8.1 on page 256) and perform a write access to the SDR-SDRAM to acknowledge this command. The write address must be chosen so that BA[1:0] are set to 0. For example, with a 16-bit 128 MB SDR-SDRAM (12 rows, 9 columns, 4 banks) bank address, the SDRAM write access should be done at the address 0x20000000. Note: This address is for example purposes only. The real address is dependent on implementation in the product. 8. For low-power SDR-SDRAM initialization, an Extended Mode Register set (EMRS) cycle is issued to program the SDR-SDRAM parameters (TCSR, PASR, DS). The application must configure the MODE field value to 5 in the Mode Register (see Section 21.8.1 on page 256) and perform a write access to the SDR- SDRAM to acknowledge this command. The write address must be chosen so that BA[1] is set to 1 and BA[0] is set to 0. For example, with a 16-bit 128 MB SDRAM, (12 rows, 9 columns, 4 banks) bank address the SDRAM write access should be done at the address 0x20800000. 9. The application must go into Normal Mode, setting Mode to 0 in the Mode Register (see Section 21.8.1 on page 256) and perform a write access at any location in the SDRAM to acknowledge this command. 10. Write the refresh rate into the count field in the DDRSDRC Refresh Timer register (see page 257). (Refresh rate = delay between refresh cycles). The SDR-SDRAM device requires a refresh every 15.625 µs or 7.81 µs. With a 100 MHz frequency, the refresh timer count register must to be set with (15.625*100 MHz) = 1562 i.e., 0x061A or (7.81*100 MHz) = 781 i.e., 0x030d After initialization, the SDR-SDRAM device is fully functional. 230 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.4.2 Low-power DDR1-SDRAM Initialization The initialization sequence is generated by software. The low-power DDR1-SDRAM devices are initialized by the following sequence: 1. Program the memory device type into the Memory Device Register (see Section 21.8.8 on page 267). 2. Program the features of the low-power DDR1-SDRAM device into the Configuration Register: asynchronous timing (trc, tras, etc.), number of columns, rows, CAS latency. See Section 21.8.3 on page 258, Section 21.8.4 on page 261 and Section 21.8.5 on page 263. 3. Program temperature compensated self refresh (tcr), Partial array self refresh (pasr) and Drive strength (ds) into the Low-power Register. See Section 21.8.7 on page 265. 4. An NOP command will be issued to the low-power DDR1-SDRAM. Program NOP command into the Mode Register, the application must configure the MODE field value to 1 in the Mode Register (see Section 21.8.1 on page 256). Perform a write access to any DDR1-SDRAM address to acknowledge this command. Now clocks which drive DDR1-SDRAM device are enabled. Note: A minimum pause of 200 µs must be respected to precede any signal toggle. 5. An all banks precharge command is issued to the low-power DDR1-SDRAM. Program all banks precharge command into the Mode Register, the application must configure the MODE field value to 2 in the Mode Register (See Section 21.8.1 on page 256). Perform a write access to any low-power DDR1-SDRAM address to acknowledge this command 6. Two auto-refresh (CBR) cycles are provided. Program the auto refresh command (CBR) into the Mode Register, the application must configure the MODE field value to 4 in the Mode Register (see Section 21.8.1 on page 256). Perform a write access to any low-power DDR1-SDRAM location twice to acknowledge these commands. 7. An Extended Mode Register set (EMRS) cycle is issued to program the low-power DDR1-SDRAM parameters (TCSR, PASR, DS). The application must configure the MODE field value to 5 in the Mode Register (see Section 21.8.1 on page 256) and perform a write access to the SDRAM to acknowledge this command. The write address must be chosen so that BA[1] is set to 1 BA[0] is set to 0. For example, with a 16-bit 128 MB SDRAM (12 rows, 9 columns, 4 banks) bank address, the low-power DDR1-SDRAM write access should be done at address 0x20800000. Note: This address is for example purposes only. The real address is dependent on implementation in the product. 8. A Mode Register set (MRS) cycle is issued to program the parameters of the low-power DDR1-SDRAM devices, in particular CAS latency, burst length. The application must configure the MODE field value to 3 in the Mode Register (see Section 21.8.1 on page 256) and perform a write access to the low-power DDR1- SDRAM to acknowledge this command. The write address must be chosen so that BA[1:0] bits are set to 0. For example, with a 16-bit 128 MB low-power DDR1-SDRAM (12 rows, 9 columns, 4 banks) bank address, the SDRAM write access should be done at the address 0x20000000. 9. The application must go into Normal Mode, setting Mode to 0 in the Mode Register (see Section 21.8.1 on page 256) and performing a write access at any location in the low-power DDR1-SDRAM to acknowledge this command. 10. Perform a write access to any low-power DDR1-SDRAM address. 11. Write the refresh rate into the count field in the DDRSDRC Refresh Timer register (see page 257). (Refresh rate = delay between refresh cycles). The low-power DDR1-SDRAM device requires a refresh every 15.625 µs or 7.81 µs. With a 100 MHz frequency, the refresh timer count register must to be set with (15.625*100 MHz) = 1562 i.e., 0x061A or (7.81*100 MHz) = 781 i.e., 0x030d After initialization, the low-power DDR1-SDRAM device is fully functional. SAM9M11 [DATASHEET] 231 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.4.3 DDR2-SDRAM Initialization The initialization sequence is generated by software. The DDR2-SDRAM devices are initialized by the following sequence: 1. Program the memory device type into the Memory Device Register (see Section 21.8.8 on page 267). 2. Program the features of DDR2-SDRAM device into the Timing Register (asynchronous timing (trc, tras, etc.)), and into the Configuration Register (number of columns, rows, CAS latency and output drive strength) (see Section 21.8.3 on page 258, Section 21.8.4 on page 261 and Section 21.8.5 on page 263). 3. An NOP command is issued to the DDR2-SDRAM. Program the NOP command into the Mode Register, the application must configure the MODE field value to 1 in the Mode Register (see Section 21.8.1 on page 256). Perform a write access to any DDR2-SDRAM address to acknowledge this command. Now clocks which drive DDR2-SDRAM device are enabled. Note: A minimum pause of 200 µs must be respected to precede any signal toggle. 4. An NOP command is issued to the DDR2-SDRAM. Program the NOP command into the Mode Register, the application must configure the MODE field value to 1 in the Mode Register (see Section 21.8.1 on page 256). Perform a write access to any DDR2-SDRAM address to acknowledge this command. Now CKE is driven high. 5. An all banks precharge command is issued to the DDR2-SDRAM. Program all banks precharge command into the Mode Register, the application must configure the MODE field value to 2 in the Mode Register (See Section 21.8.1 on page 256). Perform a write access to any DDR2-SDRAM address to acknowledge this command 6. An Extended Mode Register set (EMRS2) cycle is issued to chose between commercial or high temperature operations. The application must configure the MODE field value to 5 in the Mode Register (see Section 21.8.1 on page 256) and perform a write access to the DDR2-SDRAM to acknowledge this command. The write address must be chosen so that BA[1] is set to 1 and BA[0] is set to 0. For example, with a 16-bit 128 MB DDR2-SDRAM (12 rows, 9 columns, 4 banks) bank address, the DDR2-SDRAM write access should be done at the address 0x20800000. Note: This address is for example purposes only. The real address is dependent on implementation in the product. 7. An Extended Mode Register set (EMRS3) cycle is issued to set the Extended Mode Register to “0”. The application must configure the MODE field value to 5 in the Mode Register (see Section 21.8.1 on page 256) and perform a write access to the DDR2-SDRAM to acknowledge this command. The write address must be chosen so that BA[1] is set to 1 and BA[0] is set to 1. For example, with a 16-bit 128 MB DDR2-SDRAM (12 rows, 9 columns, 4 banks) bank address, the DDR2-SDRAM write access should be done at the address 0x20C00000. 8. An Extended Mode Register set (EMRS1) cycle is issued to enable DLL. The application must configure the MODE field value to 5 in the Mode Register (see Section 21.8.1 on page 256) and perform a write access to the DDR2-SDRAM to acknowledge this command. The write address must be chosen so that BA[1] is set to 0 and BA[0] is set to 1. For example, with a 16-bit 128 MB DDR2-SDRAM (12 rows, 9 columns, 4 banks) bank address, the DDR2-SDRAM write access should be done at the address 0x20400000. Note: An additional 200 cycles of clock are required for locking DLL 9. Program DLL field into the Configuration Register (see Section 21.8.3 on page 258) to high (Enable DLL reset). 10. A Mode Register set (MRS) cycle is issued to reset DLL. The application must configure the MODE field value to 3 in the Mode Register (see Section 21.8.1 on page 256) and perform a write access to the DDR2- SDRAM to acknowledge this command. The write address must be chosen so that BA[1:0] bits are set to 0. For example, with a 16-bit 128 MB DDR2-SDRAM (12 rows, 9 columns, 4 banks) bank address, the SDRAM write access should be done at the address 0x20000000. 11. An all banks precharge command is issued to the DDR2-SDRAM. Program all banks precharge command into the Mode Register, the application must configure the MODE field value to 2 in the Mode Register (See 232 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Section 21.8.1 on page 256). Perform a write access to any DDR2-SDRAM address to acknowledge this command 12. Two auto-refresh (CBR) cycles are provided. Program the auto refresh command (CBR) into the Mode Register, the application must configure the MODE field value to 4 in the Mode Register (see Section 21.8.1 on page 256). Performs a write access to any DDR2-SDRAM location twice to acknowledge these commands. 13. Program DLL field into the Configuration Register (see Section 21.8.3 on page 258) to low (Disable DLL reset). 14. A Mode Register set (MRS) cycle is issued to program the parameters of the DDR2-SDRAM devices, in particular CAS latency, burst length and to disable DLL reset. The application must configure the MODE field value to 3 in the Mode Register (see Section 21.8.1 on page 256) and perform a write access to the DDR2- SDRAM to acknowledge this command. The write address must be chosen so that BA[1:0] are set to 0. For example, with a 16-bit 128 MB SDRAM (12 rows, 9 columns, 4 banks) bank address, the SDRAM write access should be done at the address 0x20000000 15. Program OCD field into the Configuration Register (see Section 21.8.3 on page 258) to high (OCD calibration default). 16. An Extended Mode Register set (EMRS1) cycle is issued to OCD default value. The application must configure the MODE field value to 5 in the Mode Register (see Section 21.8.1 on page 256) and perform a write access to the DDR2-SDRAM to acknowledge this command. The write address must be chosen so that BA[1] is set to 0 and BA[0] is set to 1. For example, with a 16-bit 128 MB DDR2-SDRAM (12 rows, 9 columns, 4 banks) bank address, the DDR2-SDRAM write access should be done at the address 0x20400000. 17. Program OCD field into the Configuration Register (see Section 21.8.3 on page 258) to low (OCD calibration mode exit). 18. An Extended Mode Register set (EMRS1) cycle is issued to enable OCD exit. The application must configure the MODE field value to 5 in the Mode Register (see Section 21.8.1 on page 256) and perform a write access to the DDR2-SDRAM to acknowledge this command. The write address must be chosen so that BA[1] is set to 0 and BA[0] is set to 1. For example, with a 16-bit 128 MB DDR2-SDRAM (12 rows, 9 columns, 4 banks) bank address, the DDR2-SDRAM write access should be done at the address 0x20400000. 19. A mode Normal command is provided. Program the Normal mode into Mode Register (see Section 21.8.1 on page 256). Perform a write access to any DDR2-SDRAM address to acknowledge this command. 20. Perform a write access to any DDR2-SDRAM address. 21. Write the refresh rate into the count field in the Refresh Timer register (see page 257). (Refresh rate = delay between refresh cycles). The DDR2-SDRAM device requires a refresh every 15.625 µs or 7.81 µs. With a 133 MHz frequency, the refresh timer count register must to be set with (15.625*133 MHz) = 2079 i.e., 0x081f or (7.81*133 MHz) = 1039 i.e., 0x040f. After initialization, the DDR2-SDRAM devices are fully functional. SAM9M11 [DATASHEET] 233 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.5 Functional Description 21.5.1 SDRAM Controller Write Cycle The DDRSDRC allows burst access or single access in normal mode (DDRSDRC_MR.MODE = 000). Whatever the access type, the DDRSDRC keeps track of the active row in each bank, thus maximizing performance. The SDRAM device is programmed with a burst length equal to 8. This determines the length of a sequential data input by the write command that is set to 8. The latency from write command to data input is fixed to 1 in the case of DDR-SDRAM devices. In the case of SDR-SDRAM devices, there is no latency from write command to data input. To initiate a single access, the DDRSDRC checks if the page access is already open. If row/bank addresses match with the previous row/bank addresses, the controller generates a write command. If the bank addresses are not identical or if bank addresses are identical but the row addresses are not identical, the controller generates a precharge command, activates the new row and initiates a write command. To comply with SDRAM timing parameters, additional clock cycles are inserted between precharge/active (t RP) commands and active/write (t RCD) command. As the burst length is fixed to 8, in the case of single access, it has to stop the burst, otherwise seven invalid values may be written. In the case of SDR-SDRAM devices, a Burst Stop command is generated to interrupt the write operation. In the case of DDR-SDRAM devices, Burst Stop command is not supported for the burst write operation. In order to then interrupt the write operation, DM must be set to 1 to mask invalid data (see Figure 21-2 on page 235 and Figure 21-5 on page 236) and DQS must continue to toggle. To initiate a burst access, the DDRSDRC uses the transfer type signal provided by the master requesting the access. If the next access is a sequential write access, writing to the SDRAM device is carried out. If the next access is a write non-sequential access, then an automatic access break is inserted, the DDRSDRC generates a precharge command, activates the new row and initiates a write command. To comply with SDRAM timing parameters, additional clock cycles are inserted between precharge/active (tRP) commands and active/write (tRCD) commands. For a definition of timing parameters, refer to Section 21.8.4 “DDRSDRC Timing Parameter 0 Register” on page 261. Write accesses to the SDRAM devices are burst oriented and the burst length is programmed to 8. It determines the maximum number of column locations that can be accessed for a given write command. When the write command is issued, 8 columns are selected. All accesses for that burst take place within these eight columns, thus the burst wraps within these 8 columns if a boundary is reached. These 8 columns are selected by addr[13:3]. addr[2:0] is used to select the starting location within the block. In the case of incrementing burst (INCR/INCR4/INCR8/INCR16), the addresses can cross the 16-byte boundary of the SDRAM device. For example, in the case of DDR-SDRAM devices, when a transfer (INCR4) starts at address 0x0C, the next access is 0x10, but since the burst length is programmed to 8, the next access is at 0x00. Since the boundary is reached, the burst is wrapping. The DDRSDRC takes this feature of the SDRAM device into account. In the case of transfer starting at address 0x04/0x08/0x0C (DDR-SDRAM devices) or starting at address 0x10/0x14/0x18/0x1C, two write commands are issued to avoid to wrap when the boundary is reached. The last write command is subject to DM input logic level. If DM is registered high, the corresponding data input is ignored and write access is not done. This avoids additional writing being done. 234 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 21-2. Single Write Access, Row Closed, Low-power DDR1-SDRAM Device SDCLK A[12:0] Row a col a COMMAND NOP PRCHG NOP ACT NOP WRITE NOP BA[1:0] 00 DQS[1:0] DM[1:0] 3 0 3 D[15:0] Da Db Trp = 2 Trcd = 2 Figure 21-3. Single Write Access, Row Closed, DDR2-SDRAM Device SDCLK A[12:0] Row a col a COMMAND NOP PRCHG NOP ACT NOP WRITE NOP BA[1:0] 00 DQS[1:0] DM[1:0] 3 0 3 D[15:0] Da Db Trp = 2 Trcd = 2 SAM9M11 [DATASHEET] 235 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 21-4. Single Write Access, Row Closed, SDR-SDRAM Device SDCLK A[12:0] Row a Col a COMMAND NOP PRCHG NOP ACT NOP WRITE BST NOP BA[1:0] 00 DM[1:0] 3 0 3 D[31:0] DaDb Trp = 2 Trcd = 2 Figure 21-5. Burst Write Access, Row Closed, Low-power DDR1-SDRAM Device SDCLK A[12:0] Row a col a COMMAND NOP PRCHG NOP ACT NOP WRITE NOP BA[1:0] 0 DQS[1:0] DM[1:0] 3 0 3 D [15:0] Da Db Dc Dd De Df Dg Dh Trp = 2 Trcd = 2 236 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 21-6. Burst Write Access, Row Closed, DDR2-SDRAM Device SDCLK A[12:0] Row a col a COMMAND NOP PRCHG NOP ACT NOP WRITE NOP BA[1:0] 0 DQS[1:0] DM[1:0] 3 0 3 D [15:0] Da Db Dc Dd De Df Dg Dh Trp = 2 Trcd = 2 Figure 21-7. Burst Write Access, Row Closed, SDR-SDRAM Device SDCLK A[12:0] Row a Col a COMMAND NOP PRCHG NOP ACT NOP WRITE NOP BST NOP BA[1:0] 0 DM[3:0] F 0 F D[31:0] DaDb DcDd DeDf DgDhs Trp Trcd A write command can be followed by a read command. To avoid breaking the current write burst, Twtr/Twrd (bl/2 + 2 = 6 cycles) should be met. See Figure 21-8 on page 238. SAM9M11 [DATASHEET] 237 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 21-8. Write Command Followed By a Read Command without Burst Write Interrupt, Low-power DDR1-SDRAM Device SDCLK A[12:0] col a col a COMMAND NOP WRITE NOP READ BST NOP BA[1:0] 0 DQS[1:0] DM[1:0] 3 0 3 D[15:0] Da DbDc Dd De Df Dg Dh Da Db Twrd = BL/2 +2 = 8/2 +2 = 6 Twr = 1 In the case of a single write access, write operation should be interrupted by a read access but DM must be input 1 cycle prior to the read command to avoid writing invalid data. See Figure 21-9. Figure 21-9. Single Write Access Followed By A Read Access Low-power DDR1-SDRAM Devices SDCLK A[12:0] Row a col a COMMAND NOP PRCHG NOP ACT NOP WRITE NOP READ BST NOP BA[1:0] 0 DQS[1:0] DM[1:0] 3 0 3 D[15:0] Da Db Da Db Data masked 238 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 21-10. SINGLE Write Access Followed By A Read Access, DDR2 -SDRAM Device SDCLK A[12:0] Row a col a COMMAND NOPPRCHG NOP ACT NOP WRITE NOP READ NOP BA[1:0] 0 DQS[1:0] DM[1:0] 3 0 3 D[15:0] Da Db Da Db Data masked twtr 21.5.2 SDRAM Controller Read Cycle The DDRSDRC allows burst access or single access in normal mode (DDRSDRC_MR.MODE =000). Whatever access type, the DDRSDRC keeps track of the active row in each bank, thus maximizing performance of the DDRSDRC. The SDRAM devices are programmed with a burst length equal to 8 which determines the length of a sequential data output by the read command that is set to 8. The latency from read command to data output is equal to 2 or 3. This value is programmed during the initialization phase (see Section 21.4.1 “SDR-SDRAM Initialization” on page 230). To initiate a single access, the DDRSDRC checks if the page access is already open. If row/bank addresses match with the previous row/bank addresses, the controller generates a read command. If the bank addresses are not identical or if bank addresses are identical but the row addresses are not identical, the controller generates a precharge command, activates the new row and initiates a read command. To comply with SDRAM timing parameters, additional clock cycles are inserted between precharge/active (Trp) commands and active/read (Trcd) command. After a read command, additional wait states are generated to comply with CAS latency. The DDRSDRC supports a CAS latency of two, two and half, and three (2 or 3 clocks delay). As the burst length is fixed to 8, in the case of single access or burst access inferior to 8 data requests, it has to stop the burst otherwise seven or X values could be read. Burst Stop Command (BST) is used to stop output during a burst read. To initiate a burst access, the DDRSDRC checks the transfer type signal. If the next accesses are sequential read accesses, reading to the SDRAM device is carried out. If the next access is a read non-sequential access, then an automatic page break can be inserted. If the bank addresses are not identical or if bank addresses are identical but the row addresses are not identical, the controller generates a precharge command, activates the new row and initiates a read command. In the case where the page access is already open, a read command is generated. To comply with SDRAM timing parameters, additional clock cycles are inserted between precharge/active (Trp) commands and active/read (Trcd) commands. The DDRSDRC supports a CAS latency of two, two and half, and three (2 or 3 clocks delay). During this delay, the controller uses internal signals to anticipate the next access and improve the performance of the controller. Depending on the latency(2/3), the DDRSDRC anticipates 2 or 3 read accesses. In the case of burst of specified length, accesses are not anticipated, but if the burst is broken (border, busy mode, etc.), the next access is treated as an incrementing burst of unspecified length, and in function of the latency(2/3), the DDRSDRC anticipates 2 or 3 read accesses. SAM9M11 [DATASHEET] 239 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

For a definition of timing parameters, refer to Section 21.8.3 “DDRSDRC Configuration Register” on page 258. Read accesses to the SDRAM are burst oriented and the burst length is programmed to 8. It determines the maximum number of column locations that can be accessed for a given read command. When the read command is issued, 8 columns are selected. All accesses for that burst take place within these eight columns, meaning that the burst wraps within these 8 columns if the boundary is reached. These 8 columns are selected by addr[13:3]; addr[2:0] is used to select the starting location within the block. In the case of incrementing burst (INCR/INCR4/INCR8/INCR16), the addresses can cross the 16-byte boundary of the SDRAM device. For example, when a transfer (INCR4) starts at address 0x0C, the next access is 0x10, but since the burst length is programmed to 8, the next access is 0x00. Since the boundary is reached, the burst wraps. The DDRSDRC takes into account this feature of the SDRAM device. In the case of DDR-SDRAM devices, transfers start at address 0x04/0x08/0x0C. In the case of SDR-SDRAM devices, transfers start at address 0x14/0x18/0x1C. Two read commands are issued to avoid wrapping when the boundary is reached. The last read command may generate additional reading (1 read cmd = 4 DDR words or 1 read cmd = 8 SDR words). To avoid additional reading, it is possible to use the burst stop command to truncate the read burst and to decrease power consumption. Figure 21-11. Single Read Access, Row Closed, Latency = 2,Low-power DDR1-SDRAM Device SDCLK A[12:0] Row a Col a COMMAND NOP PRCHG NOP ACT NOP READ BST NOP BA[1:0] 0 DQS[1] DQS[0] DM[1:0] 3 D[15:0] Da Db Trp Trcd Latency = 2 240 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 21-12. Single Read Access, Row Closed, Latency = 3, DDR2-SDRAM Device SDCLK A[12:0] Row a Column a COMMAND NOP PRCHG NOP ACT NOP READ BA[1:0] 0 DQS[1] DQS[0] DM[1:0] 3 D[15:0] Da Db TRP TRCD Latency = 3 Figure 21-13. Single Read Access, Row Closed, Latency = 2, SDR-SDRAM Device SDCLK A[12:0] Row a col a COMMAND NOP PRCHG NOP ACT NOP READ BST NOP BA[1:0] 0 DM[3:0] 3 D[31:0] DaDb Trp Trcd Latency = 2 SAM9M11 [DATASHEET] 241 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 21-14. Burst Read Access, Latency = 2, Low-power DDR1-SDRAM Devices SDCLK A[12:0] Col a COMMAND NOP READ NOP BA[1:0] 0 DQS[1:0] DM[1:0] 3 D[15:0] Da Db Dc Dd De Df Dg Dh Latency = 2 Figure 21-15. Burst Read Access, Latency = 3, DDR2-SDRAM Devices SDCLK A[12:0] Col a COMMAND NOP READ NOP BA[1:0] 0 DQS[1:0] DM[1:0] 3 D[15:0] Da Db Dc Dd De Df Dg Dh Latency = 3 242 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 21-16. Burst Read Access, Latency = 2, SDR-SDRAM Devices SDCLK A[12:0] col a COMMAND NOP READ NOP BST NOP BA[1:0] 0 DQS[1:0] DM[3:0] F D[31:0] DaDb DcDd DeDf Dg Dh Latency = 2 21.5.3 Refresh (Auto-refresh Command) An auto-refresh command is used to refresh the DDRSDRC. Refresh addresses are generated internally by the SDRAM device and incremented after each auto-refresh automatically. The DDRSDRC generates these auto- refresh commands periodically. A timer is loaded with the value in the register DDRSDRC_TR that indicates the number of clock cycles between refresh cycles. When the DDRSDRC initiates a refresh of an SDRAM device, internal memory accesses are not delayed. However, if the CPU tries to access the SDRAM device, the slave indicates that the device is busy. A request of refresh does not interrupt a burst transfer in progress. 21.5.4 Power Management 21.5.4.1 Self Refresh Mode This mode is activated by setting low-power command bits [LPCB] to ‘01’ in the DDRSDRC_LPR. Self refresh mode is used to reduce power consumption, i.e., when no access to the SDRAM device is possible. In this case, power consumption is very low. In self refresh mode, the SDRAM device retains data without external clocking and provides its own internal clocking, thus performing its own auto-refresh cycles. All the inputs to the SDRAM device become “don’t care” except CKE, which remains low. As soon as the SDRAM device is selected, the DDRSDRC provides a sequence of commands and exits self refresh mode. The DDRSDRC re-enables self refresh mode as soon as the SDRAM device is not selected. It is possible to define when self refresh mode will be enabled by setting the register LPR (see Section 21.8.7 “DDRSDRC Low-power Register” on page 265), timeout command bit:  00 = Self refresh mode is enabled as soon as the SDRAM device is not selected  01 = Self refresh mode is enabled 64 clock cycles after completion of the last access  10 = Self refresh mode is enabled 128 clock cycles after completion of the last access As soon as the SDRAM device is no longer selected, PRECHARGE ALL BANKS command is generated followed by a SELF-REFREFSH command. If, between these two commands an SDRAM access is detected, SELF- REFREFSH command will be replaced by an AUTO-REFRESH command. According to the application, more AUTO-REFRESH commands will be performed when the self refresh mode is enabled during the application. This controller also interfaces low-power SDRAM. These devices add a new feature: A single quarter, one half quarter or all banks of the SDRAM array can be enabled in self refresh mode. Disabled banks will be not refreshed in self refresh mode. This feature permits to reduce the self refresh current. The extended mode register controls this feature, it includes Temperature Compensated Self Refresh (TSCR), Partial Array Self Refresh (PASR) SAM9M11 [DATASHEET] 243 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

parameters and Drive Strength (DS). These parameters are set during the initialization phase. After initialization, as soon as PASR/DS/TCSR fields are modified, the Extended Mode Register in the memory of the external device is accessed automatically and PASR/DS/TCSR bits are updated before entry into self refresh mode if DDRSDRC does not share an external bus with another controller or during a refresh command, and a pending read or write access, if DDRSDRC does share an external bus with another controller. This type of update depends on the value of the UPD_MR field (see Section 21.8.7 “DDRSDRC Low-power Register” on page 265). The low-power SDR-SDRAM must remain in self refresh mode for a minimum period of TRAS periods and may remain in self refresh mode for an indefinite period. (See Figure 21-17) The low-power DDR1-SDRAM must remain in self refresh mode for a minimum of TRFC periods and may remain in self refresh mode for an indefinite period. The DDR2-SDRAM must remain in self refresh mode for a minimum of TCKE periods and may remain in self refresh mode for an indefinite period. Figure 21-17. Self Refresh Mode Entry, Timeout = 0 SDCLK A[12:0] COMMAND NOP READ BST NOP PRCHG NOP ARFSH NOP CKE BA[1:0] 0 DQS[0:1] DM[1:0] 3 D[15:0] Da Db Enter Self refresh Mode Trp 244 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 21-18. Self Refresh Mode Entry, Timeout = 1 or 2 SDCLK A[12:0] COMMAND NOPREAD BST NOP PRCHG NOP ARFSH NOP CKE BA[1:0] 0 DQS[1:0] DM[1:0] 3 D[15:0] Da Db 64 or 128 Trp Enter Self refresh wait states Mode Figure 21-19. Self Refresh Mode Exit SDCLK A[12:0] COMMAND NOP VALID NOP CKE BA[1:0] 0 DQS[1:0] DM[1:0] 3 D[15:0] DaDb Exit Self Refresh mode clock must be stable TXNRD/TXSRD (DDR device) before exiting self refresh mode TXSR (Low-power DDR1 device) TXSR (Low-power SDR, SDR-SDRAM device) SAM9M11 [DATASHEET] 245 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 21-20. Self Refresh and Automatic Update SDCLK A[12:0] Pasr-Tcr-Ds COMMAND NOP PRCHG NOP MRS NOP ARFSH NOP CKE BA[1:0] 0 2 Enter Self Refresh Mode Trp Tmrd Update Extended Mode register Figure 21-21. Automatic Update During AUTO-REFRESH Command and SDRAM Access SDCLK A[12:0] Pasr-Tcr-Ds COMMAND NOP PRCHALL NOP ARFSH NOP MRS NOP ACT CKE BA[1:0] 0 2 0 Trp Trfc Tmrd Update Extended mode register 246 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.5.4.2 Power-down Mode This mode is activated by setting the low-power command bits [LPCB] to ‘10’. Power-down mode is used when no access to the SDRAM device is possible. In this mode, power consumption is greater than in self refresh mode. This state is similar to normal mode (No low-power mode/No self refresh mode), but the CKE pin is low and the input and output buffers are deactivated as soon the SDRAM device is no longer accessible. In contrast to self refresh mode, the SDRAM device cannot remain in low-power mode longer than the refresh period (64 ms). As no auto-refresh operations are performed in this mode, the DDRSDRC carries out the refresh operation. In order to exit low-power mode, a NOP command is required in the case of Low-power SDR- SDRAM and SDR-SDRAM devices. In the case of Low-power DDR1-SDRAM devices, the controller generates a NOP command during a delay of at least TXP. In addition, Low-power DDR1-SDRAM and DDR2-SDRAM must remain in power-down mode for a minimum period of TCKE periods. The exit procedure is faster than in self refresh mode. See Figure 21-22. The DDRSDRC returns to power-down mode as soon as the SDRAM device is not selected. It is possible to define when power-down mode is enabled by setting the register LPR, timeout command bit.  00 = Power-down mode is enabled as soon as the SDRAM device is not selected  01 = Power-down mode is enabled 64 clock cycles after completion of the last access  10 = Power-down mode is enabled 128 clock cycles after completion of the last access Figure 21-22. Power-down Entry/Exit, Timeout = 0 SDCLK A[12:0] COMMAND READ BST NOP READ CKE BA[1:0] 0 DQS[1:0] DM[1:0] 3 D[15:0] Da Db Entry power down mode Exit power down mode SAM9M11 [DATASHEET] 247 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.5.4.3 Deep Power-down Mode The deep power-down mode is a new feature of the Low-power SDRAM. When this mode is activated, all internal voltage generators inside the device are stopped and all data is lost. This mode is activated by setting the low-power command bits [LPCB] to ‘11’. When this mode is enabled, the DDRSDRC leaves normal mode (DDRSDRC_MR.MODE = 000) and the controller is frozen. To exit deep power- down mode, the low-power bits (LPCB) must be set to “00”, an initialization sequence must be generated by software. See Section 21.4.2 “Low-power DDR1-SDRAM Initialization” on page 231. Figure 21-23. Deep Power-down Mode Entry SDCLK A[12:0] COMMAND NOP READ BST NOP PRCHG NOP DEEPOWER NOP CKE BA[1:0] 0 DQS[1:0] DM[1:0] 3 D[15:0] Da Db Enter Deep Trp Power-down Mode 21.5.4.4 Reset Mode The reset mode is a feature of the DDR2-SDRAM. This mode is activated by setting the low-power command bits (LPCB) to 11 and the clock frozen command bit (CLK_FR) to 1. When this mode is enabled, the DDRSDRC leaves normal mode (DDRSDRC_MR.MODE = 000) and the controller is frozen. Before enabling this mode, the end user must assume there is not an access in progress. To exit reset mode, the low-power command bits (LPCB) must be set to “00”, clock frozen command bit (CLK_FR) set to 0 and an initialization sequence must be generated by software. See Section 21.4.3 “DDR2-SDRAM Initialization” on page 232. 248 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.5.5 Multi-port Functionality The SDRAM protocol imposes a check of timings prior to performing a read or a write access, thus decreasing the performance of systems. An access to SDRAM is performed if banks and rows are open (or active). To activate a row in a particular bank, it has to de-active the last open row and open the new row. Two SDRAM commands must be performed to open a bank: Precharge and Active command with respect to Trp timing. Before performing a read or write command, Trcd timing must checked. This operation represents a significative loss. (see Figure 21-24). Figure 21-24. Trp and Trcd Timings SDCLK A[12:0] COMMAND NOP PRCHG NOP ACT NOP READ BST NOP BA[1:0] 0 DQS[1:0] DM1:0] 3 D[15:0] Da Db Trp Trcd Latency =2 4 cycles before performing a read command The multi-port controller has been designed to mask these timings and thus improve the bandwidth of the system. DDRSDRC is a multi-port controller since four masters can simultaneously reach the controller. This feature improves the bandwidth of the system because it can detect four requests on the AHB slave inputs and thus anticipate the commands that follow, PRECHARGE and ACTIVE commands in bank X during current access in bank Y. This allows Trp and Trcd timings to be masked (see Figure 21-25). In the best case, all accesses are done as if the banks and rows were already open. The best condition is met when the four masters work in different banks. In the case of four simultaneous read accesses, when the four banks and associated rows are open, the controller reads with a continuous flow and masks the CAS latency for each different access. To allow a continuous flow, the read command must be set at 2 or 3 cycles (CAS latency) before the end of current access. This requires that the scheme of arbitration changes since the round-robin arbitration cannot be respected. If the controller anticipates a read access, and thus before the end of current access a master with a high priority arises, then this master will not serviced. The arbitration mechanism reduces latency when conflicts occur, i.e., when two or more masters try to access the SDRAM device at the same time. The arbitration type is round-robin arbitration. This algorithm dispatches the requests from different masters to the SDRAM device in a round-robin manner. If two or more master requests arise at the same time, the master with the lowest number is serviced first, then the others are serviced in a round-robin manner. To avoid burst breaking and to provide the maximum throughput for the SDRAM device, arbitration may only take place during the following cycles: 1. Idle cycles: When no master is connected to the SDRAM device. SAM9M11 [DATASHEET] 249 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

2. Single cycles: When a slave is currently doing a single access. 3. End of Burst cycles: When the current cycle is the last cycle of a burst transfer. For bursts of defined length, predicted end of burst matches the size of the transfer. For bursts of undefined length, predicted end of burst is generated at the end of each four beat boundary inside the INCR transfer. 4. Anticipated Access: When an anticipate read access is done while current access is not complete, the arbitration scheme can be changed if the anticipated access is not the next access serviced by the arbitration scheme. Figure 21-25. Anticipate Precharge/Active Command in Bank 2 during Read Access in Bank 1 SDClK A[12:0] COMMAND NOP READ PRECH NOP ACT READ NOP BA[1:0] 0 1 2 1 DQS[1:0] DM1:0] 3 D[15:0] Da Db Dc Dd De Df Dg Dh Di Dj Dk Dl Trp Anticipate command, Precharge/Active Bank 2 Read access in Bank 1 250 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.5.6 Write Protected Registers To prevent any single software error that may corrupt DDRSDRC behavior, the registers listed below can be write- protected by setting the WPEN bit in the DDRSDRC Write Protect Mode Register (DDRSDRC_WPMR). If a write access in a write-protected register is detected, then the WPVS flag in the DDRSDRC Write Protect Status Register (DDRSDRC_WPSR) is set and the field WPVSRC indicates in which register the write access has been attempted. The WPVS flag is automatically reset after reading the DDRSDRC Write Protect Status Register (DDRSDRC_WPSR). Following is a list of the write protected registers:  “DDRSDRC Mode Register” on page 256  “DDRSDRC Refresh Timer Register” on page 257  “DDRSDRC Configuration Register” on page 258  “DDRSDRC Timing Parameter 0 Register” on page 261  “DDRSDRC Timing Parameter 1 Register” on page 263  “DDRSDRC Timing Parameter 2 Register” on page 264  “DDRSDRC Memory Device Register” on page 267  “DDRSDRC High Speed Register” on page 269 SAM9M11 [DATASHEET] 251 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.6 Software Interface/SDRAM Organization, Address Mapping The SDRAM address space is organized into banks, rows and columns. The DDRSDRC maps different memory types depending on the values set in the DDRSDRC Configuration Register. See Section 21.8.3 “DDRSDRC Configuration Register” on page 258. The following figures illustrate the relation between CPU addresses and columns, rows and banks addresses for 16-bit memory data bus widths and 32-bit memory data bus widths. The DDRSDRC supports address mapping in linear mode. Linear mode is a method for address mapping where banks alternate at each last SDRAM page of current bank. The DDRSDRC makes the SDRAM devices access protocol transparent to the user. Table 21-1 to Table 21-7 illustrate the SDRAM device memory mapping seen by the user in correlation with the device structure. Various configurations are illustrated. 21.6.1 SDRAM Address Mapping for 16-bit Memory Data Bus Width(1) and Four Banks Table 21-1. Linear Mapping for SDRAM Configuration, 2K Rows, 512/1024/2048/4096 Columns CPU Address Line 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bk[1:0] Row[10:0] Column[8:0] M0 Bk[1:0] Row[10:0] Column[9:0] M0 Bk[1:0] Row[10:0] Column[10:0] M0 Bk[1:0] Row[10:0] Column[11:0] M0 Table 21-2. Linear Mapping for SDRAM Configuration: 4K Rows, 512/1024/2048/4096 Columns CPU Address Line 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bk[1:0] Row[11:0] Column[8:0] M0 Bk[1:0] Row[11:0] Column[9:0] M0 Bk[1:0] Row[11:0] Column[10:0] M0 Bk[1:0] Row[11:0] Column[11:0] M0 Table 21-3. Linear Mapping for SDRAM Configuration: 8K Rows, 512/1024/2048/4096 Columns CPU Address Line 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bk[1:0] Row[12:0] Column[8:0] M0 Bk[1:0] Row[12:0] Column[9:0] M0 Bk[1:0] Row[12:0] Column[10:0] M0 Bk[1:0] Row[12:0] Column[11:0] M0 252 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 21-4. Linear Mapping for SDRAM Configuration: 16K Rows, 512/1024/2048 Columns CPU Address Line 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bk[1:0] Row[13:0] Column[8:0] M0 Bk[1:0] Row[13:0] Column[9:0] M0 Bk[1:0] Row[13:0] Column[10:0] M0 Note: 1. SDR-SDRAM devices with eight columns in 16-bit mode are not supported. 21.6.2 SDR-SDRAM Address Mapping for 32-bit Memory Data Bus Width Table 21-5. SDR-SDRAM Configuration Mapping: 2K Rows, 256/512/1024/2048 Columns CPU Address Line 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bk[1:0] Row[10:0] Column[7:0] M[1:0] Bk[1:0] Row[10:0] Column[8:0] M[1:0] Bk[1:0] Row[10:0] Column[9:0] M[1:0] Bk[1:0] Row[10:0] Column[10:0] M[1:0] Table 21-6. SDR-SDRAM Configuration Mapping: 4K Rows, 256/512/1024/2048 Columns CPU Address Line 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bk[1:0] Row[11:0] Column[7:0] M[1:0] Bk[1:0] Row[11:0] Column[8:0] M[1:0] Bk[1:0] Row[11:0] Column[9:0] M[1:0] Bk[1:0] Row[11:0] Column[10:0] M[1:0] Table 21-7. SDR-SDRAM Configuration Mapping: 8K Rows, 256/512/1024/2048 Columns CPU Address Line 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bk[1:0] Row[12:0] Column[7:0] M[1:0] Bk[1:0] Row[12:0] Column[8:0] M[1:0] Bk[1:0] Row[12:0] Column[9:0] M[1:0] Bk[1:0] Row[12:0] Column[10:0] M[1:0] Notes: 1. M[1:0] is the byte address inside a 32-bit word. 2. Bk[1] = BA1, Bk[0] = BA0 SAM9M11 [DATASHEET] 253 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.7 Programmable IO Delays The external bus interface consists of a data bus, an address bus and control signals. The simultaneous switching outputs on these busses may lead to a peak of current in the internal and external power supply lines. In order to reduce the peak of current in such cases, additional propagation delays can be adjusted independently for pad buffers by means of configuration registers, DDRSDRC_DELAY1–8. The additional programmable delays for each IO range from 0 to 4 ns (Worst Case PVT). The delay can differ between IOs supporting this feature. Delay can be modified per programming for each IO. The minimal additional delay that can be programmed on a PAD supporting this feature is 1/16 of the maximum programmable delay. When programming 0x0 in fields “Delay1 to Delay8”, no delay is added (reset value) and the propagation delay of the pad buffers is the inherent delay of the pad buffer. When programming 0xF in field “Delay1” the propagation delay of the corresponding pad is maximal. DDRSDRC_DELAY1, DDRSDRC_DELAY2 allow to configure delay on D[15:0], DDRSDRC_DELAY1[3:0] corresponds to D[0] and DDRSDRC_DELAY2[3:0] corresponds to D[8]. DDRSDRC_DELAY3, DDRSDRC_DELAY4 allow to configure delay on A13:0], DDRSDRC_DELAY3[3:0] corresponds to A[0] and DDRSDRC_DELAY4[3:0] corresponds to A[8]. Figure 21-26. Programmable IO Delays D_in[0] SMC D_out[0] Programmable Delay Line D[0] DELAY1 D_in[1] D_out[1] Programmable Delay Line D[1] DELAY2 D_in[n] D_out[n] Programmable Delay Line D[n] DELAYx A[m] Programmable Delay Line A[m] DELAYy 254 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.8 DDR SDR SDRAM Controller (DDRSDRC) User Interface The User Interface is connected to the APB bus. The DDRSDRC is programmed using the registers listed in Table 21-8. Table 21-8. Register Mapping Offset Register Name Access Reset 0x00 DDRSDRC Mode Register DDRSDRC_MR Read/Write 0x00000000 0x04 DDRSDRC Refresh Timer Register DDRSDRC_RTR Read/Write 0x00000000 0x08 DDRSDRC Configuration Register DDRSDRC_CR Read/Write 0x7024 0x0C DDRSDRC Timing Parameter 0 Register DDRSDRC_TPR0 Read/Write 0x20227225 0x10 DDRSDRC Timing Parameter 1 Register DDRSDRC_TPR1 Read/Write 0x3C80808 0x14 DDRSDRC Timing Parameter 2 Register DDRSDRC_TPR2 Read/Write 0x2062 0x18 Reserved – – – 0x1C DDRSDRC Low-power Register DDRSDRC_LPR Read/Write 0x10000 0x20 DDRSDRC Memory Device Register DDRSDRC_MD Read/Write 0x10 0x24 DDRSDRC DLL Information Register DDRSDRC_DLL Read-only 0x00000001 0x2C DDRSDRC High Speed Register DDRSDRC_HS Read/Write 0x0 0x40 DDRSDRC Delay I/O Register DDRSDRC_DELAY1 Read/Write 0x00000000 0x44 DDRSDRC Delay I/O Register DDRSDRC_DELAY2 Read/Write 0x00000000 0x48 DDRSDRC Delay I/O Register DDRSDRC_DELAY3 Read/Write 0x00000000 0x4C DDRSDRC Delay I/O Register DDRSDRC_DELAY4 Read/Write 0x00000000 0x50 Reserved – – – 0x54–0x58 Reserved – – – 0x60–0xE0 Reserved – – – 0xE4 DDRSDRC Write Protect Mode Register DDRSDRC_WPMR Read/Write 0x00000000 0xE8 DDRSDRC Write Protect Status Register DDRSDRC_WPSR Read-only 0x00000000 SAM9M11 [DATASHEET] 255 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.8.1 DDRSDRC Mode Register Name: DDRSDRC_MR Address: 0xFFFFE600 (0), 0xFFFFE400 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – MODE This register can only be written if the bit WPEN is cleared in “DDRSDRC Write Protect Mode Register” on page 271. • MODE: DDRSDRC Command Mode This field defines the command issued by the DDRSDRC when the SDRAM device is accessed. This register is used to ini- tialize the SDRAM device and to activate deep power-down mode. MODE Description Normal Mode. Any access to the DDRSDRC will be decoded normally. To activate this mode, command must be followed 000 by a write to the SDRAM. The DDRSDRC issues a NOP command when the SDRAM device is accessed regardless of the cycle. To activate this 001 mode, command must be followed by a write to the SDRAM. The DDRSDRC issues an “All Banks Precharge” command when the SDRAM device is accessed regardless of the cycle. 010 To activate this mode, command must be followed by a write to the SDRAM. The DDRSDRC issues a “Load Mode Register” command when the SDRAM device is accessed regardless of the cycle. 011 To activate this mode, command must be followed by a write to the SDRAM. The DDRSDRC issues an “Auto-Refresh” Command when the SDRAM device is accessed regardless of the cycle. 100 Previously, an “All Banks Precharge” command must be issued. To activate this mode, command must be followed by a write to the SDRAM. The DDRSDRC issues an “Extended Load Mode Register” command when the SDRAM device is accessed regardless of 101 the cycle. To activate this mode, the “Extended Load Mode Register” command must be followed by a write to the SDRAM. The write in the SDRAM must be done in the appropriate bank. 110 Deep power mode: Access to deep power-down mode 111 Reserved 256 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.8.2 DDRSDRC Refresh Timer Register Name: DDRSDRC_RTR Address: 0xFFFFE604 (0), 0xFFFFE404 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – COUNT 7 6 5 4 3 2 1 0 COUNT This register can only be written if the bit WPEN is cleared in “DDRSDRC Write Protect Mode Register” on page 271. • COUNT: DDRSDRC Refresh Timer Count This 12-bit field is loaded into a timer which generates the refresh pulse. Each time the refresh pulse is generated, a refresh sequence is initiated. SDRAM devices require a refresh of all rows every 64 ms. The value to be loaded depends on the DDRSDRC clock fre- quency (MCK: Master Clock) and the number of rows in the device. For example, for an SDRAM with 8192 rows and a 100 MHz Master clock, the value of Refresh Timer Count bit is pro- grammed: (((64 x 10-3)/8192) x100 x106 = 781 or 0x030D. SAM9M11 [DATASHEET] 257 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.8.3 DDRSDRC Configuration Register Name: DDRSDRC_CR Address: 0xFFFFE608 (0), 0xFFFFE408 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – ACTBST – EBISHARE 15 14 13 12 11 10 9 8 – OCD – – DIS_DLL DIC/DS 7 6 5 4 3 2 1 0 DLL CAS NR NC This register can only be written if the bit WPEN is cleared in “DDRSDRC Write Protect Mode Register” on page 271. • NC: Number of Column Bits The reset value is 9 column bits. SDR-SDRAM devices with eight columns in 16-bit mode are not supported. NC DDR - Column bits SDR - Column bits 00 9 8 01 10 9 10 11 10 11 12 11 • NR: Number of Row Bits The reset value is 12 row bits. NR Row bits 00 11 01 12 10 13 11 14 258 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• CAS: CAS Latency The reset value is 2 cycles. CAS DDR2 CAS Latency SDR CAS Latency 000 Reserved Reserved 001 Reserved Reserved 010 Reserved 2 011 3 3 100 Reserved Reserved 101 Reserved Reserved 110 Reserved Reserved 111 Reserved Reserved • DLL: Reset DLL Reset value is 0. This field defines the value of Reset DLL. 0: Disable DLL reset. 1: Enable DLL reset. This value is used during the power-up sequence. Note: This field is found only in DDR2-SDRAM devices. • DIC/DS: Output Driver Impedance Control Reset value is 0. This field defines the output drive strength. 0: Normal driver strength. 1: Weak driver strength. This value is used during the power-up sequence. This parameter is found in the datasheet as DIC or DS. Note: This field is found only in DDR2-SDRAM devices. • DIS_DLL: Disable DLL Reset value is 0. 0: Enable DLL 1: Disable DLL Note: This field is found only in DDR2-SDRAM devices. • OCD: Off-chip Driver Reset value is 7. Note: OCD is NOT supported by the controller, but these values MUST be programmed during the initialization sequence. Note: This field is found only in DDR2-SDRAM devices. OCD 000 OCD calibration mode exit, maintain setting 111 OCD calibration default SAM9M11 [DATASHEET] 259 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• EBISHARE: External Bus Interface is Shared The DDR controller embedded in the EBI is used at the same time as another memory controller (SMC,..) Reset value is 0. 0: Only the DDR controller function is used. 1: The DDR controller shares the EBI with another memory controller (SMC, NAND,..) • ACTBST: ACTIVE Bank X to Burst Stop Read Access Bank Y Reset value is 0. 0: After an ACTIVE command in Bank X, BURST STOP command can be issued to another bank to stop current read access. 1: After an ACTIVE command in Bank X, BURST STOP command cannot be issued to another bank to stop current read access. This field is unique to SDR-SDRAM, Low-power SDR-SDRAM and Low-power DDR1-SDRAM devices. 260 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.8.4 DDRSDRC Timing Parameter 0 Register Name: DDRSDRC_TPR0 Address: 0xFFFFE60C (0), 0xFFFFE40C (1) Access: Read/Write 31 30 29 28 27 26 25 24 TMRD REDUCE_WRRD TWTR 23 22 21 20 19 18 17 16 TRRD TRP 15 14 13 12 11 10 9 8 TRC TWR 7 6 5 4 3 2 1 0 TRCD TRAS This register can only be written if the bit WPEN is cleared in “DDRSDRC Write Protect Mode Register” on page 271. • TRAS: Active to Precharge Delay Reset value is 5 cycles. This field defines the delay between an Activate Command and a Precharge Command in number of cycles. Number of cycles is between 0 and 15. • TRCD: Row to Column Delay Reset value is 2 cycles. This field defines the delay between an Activate Command and a Read/Write Command in number of cycles. Number of cycles is between 0 and 15. • TWR: Write Recovery Delay Reset value is 2 cycles. This field defines the Write Recovery Time in number of cycles. Number of cycles is between 1 and 15. • TRC: Row Cycle Delay Reset value is 7 cycles. This field defines the delay between an Activate command and Refresh command in number of cycles. Number of cycles is between 0 and 15. • TRP: Row Precharge Delay Reset value is 2 cycles. This field defines the delay between a Precharge Command and another command in number of cycles. Number of cycles is between 0 and 15. • TRRD: Active bankA to Active bankB Reset value is 2 cycles. This field defines the delay between an Active command in BankA and an active command in bankB in number of cycles. Number of cycles is between 1 and 15. SAM9M11 [DATASHEET] 261 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• TWTR: Internal Write to Read Delay Reset value is 0. This field is unique to Low-power DDR1-SDRAM devices and DDR2-SDRAM devices. This field defines the internal write to read command Time in number of cycles. Number of cycles is between 1 and 7. Value Name Description 1 ONE does 1 2 TWO does 2 3 THREE does 3 4 FOUR does 4 5 FIVE does 5 6 SIX does 6 7 SEVEN does 7 In the case of low-power DDR1-SDRAM device the coding is different: Value Name Description 0 ONE does 1 1 TWO does 2 2–7 – Reserved • REDUCE_WRRD: Reduce Write to Read Delay Reset value is 0. This field reduces the delay between write to read access for low-power DDR-SDRAM devices with a latency equal to 2. To use this feature, TWTR field must be equal to 0. Important to note is that some devices do not support this feature. • TMRD: Load Mode Register Command to Active or Refresh Command Reset value is 2 cycles. This field defines the delay between a Load mode register command and an active or refresh command in number of cycles. Number of cycles is between 0 and 15. 262 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.8.5 DDRSDRC Timing Parameter 1 Register Name: DDRSDRC_TPR1 Address: 0xFFFFE610 (0), 0xFFFFE410 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – TXP 23 22 21 20 19 18 17 16 TXSRD 15 14 13 12 11 10 9 8 TXSNR 7 6 5 4 3 2 1 0 – – – TRFC This register can only be written if the bit WPEN is cleared in “DDRSDRC Write Protect Mode Register” on page 271. • TRFC: Row Cycle Delay Reset value is 8 cycles. This field defines the delay between a Refresh and an Activate command or Refresh command in number of cycles. Num- ber of cycles is between 0 and 31. • TXSNR: Exit Self Refresh Delay to Non-read Command Reset value is 8 cycles. This field defines the delay between CKE set high and a non Read Command in number of cycles. Number of cycles is between 0 and 255. This field is used for SDR-SDRAM and DDR-SDRAM devices. In the case of SDR-SDRAM devices and Low-power DDR1-SDRAM, this field is equivalent to TXSR timing. • TXSRD: Exit Self Refresh Delay to Read Command Reset value is 200 cycles. This field defines the delay between CKE set high and a Read Command in number of cycles. Number of cycles is between 0 and 255 cycles. This field is unique to DDR-SDRAM devices. In the case of a Low-power DDR1-SDRAM, this field must be written to 0. • TXP: Exit Power-down Delay to First Command Reset value is 3 cycles. This field defines the delay between CKE set high and a Valid Command in number of cycles. Number of cycles is between 0 and 15 cycles. This field is unique to Low-power DDR1-SDRAM devices and DDR2-SDRAM devices. SAM9M11 [DATASHEET] 263 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.8.6 DDRSDRC Timing Parameter 2 Register Name: DDRSDRC_TPR2 Address: 0xFFFFE614 (0), 0xFFFFE414 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – TRTP TRPA 7 6 5 4 3 2 1 0 TXARDS TXARD This register can only be written if the bit WPEN is cleared in “DDRSDRC Write Protect Mode Register” on page 271. • TXARD: Exit Active Power Down Delay to Read Command in Mode “Fast Exit” Reset value is 2 cycles. This field defines the delay between CKE set high and a Read Command in number of cycles. Number of cycles is between 0 and 15. Note: This field is found only in DDR2-SDRAM devices. • TXARDS: Exit Active Power Down Delay to Read Command in Mode “Slow Exit” Reset value is 6 cycles. This field defines the delay between CKE set high and a Read Command in number of cycles. Number of cycles is between 0 and 15. Note: This field is found only in DDR2-SDRAM devices. • TRPA: Row Precharge All Delay Reset value is 0 cycles. This field defines the delay between a Precharge ALL banks Command and another command in number of cycles. Num- ber of cycles is between 0 and 15. Note: This field is found only in DDR2-SDRAM devices. • TRTP: Read to Precharge Reset value is 2 cycles. This field defines the delay between Read Command and a Precharge command in number of cycle. Number of cycles is between 0 and 7. 264 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.8.7 DDRSDRC Low-power Register Name: DDRSDRC_LPR Address: 0xFFFFE61C (0), 0xFFFFE41C (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – UPD_MR – – – APDE 15 14 13 12 11 10 9 8 – – TIMEOUT DS TCR 7 6 5 4 3 2 1 0 – PASR CLK_FR LPCB • LPCB: Low-power Command Bit Reset value is “00”. 00: Low-power Feature is inhibited: no power-down, self refresh and Deep power mode are issued to the SDRAM device. 01: The DDRSDRC issues a Self Refresh Command to the SDRAM device, the clock(s) is/are de-activated and the CKE signal is set low. The SDRAM device leaves the self refresh mode when accessed and enters it after the access. 10: The DDRSDRC issues a Power-down Command to the SDRAM device after each access, the CKE signal is set low. The SDRAM device leaves the power-down mode when accessed and enters it after the access. 11: The DDRSDRC issues a Deep Power-down Command to the Low-power SDRAM device. This mode is unique to Low-power SDRAM devices. • CLK_FR: Clock Frozen Command Bit Reset value is “0”. This field sets the clock low during power-down mode or during deep power-down mode. Some SDRAM devices do not support freezing the clock during power-down mode or during deep power-down mode. Refer to the SDRAM device data- sheet for details on this. 1: Clock(s) is/are frozen. 0: Clock(s) is/are not frozen. • PASR: Partial Array Self Refresh Reset value is “0”. This field is unique to Low-power SDRAM. It is used to specify whether only one quarter, one half or all banks of the SDRAM array are enabled. Disabled banks are not refreshed in self refresh mode. The values of this field are dependant on Low-power SDRAM devices. After the initialization sequence, as soon as PASR field is modified, Extended Mode Register in the external device mem- ory is accessed automatically and PASR bits are updated. Depending on the value of the UPD_MR field, update is done before entering in self refresh mode or during a refresh command and a pending read or write access. SAM9M11 [DATASHEET] 265 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• TCR: Temperature Compensated Self Refresh Reset value is “0”. This field is unique to Low-power SDRAM. It is used to program the refresh interval during self refresh mode, depending on the case temperature of the low-power SDRAM. The values of this field are dependent on Low-power SDRAM devices. After the initialization sequence, as soon as TCR field is modified, Extended Mode Register is accessed automatically and TCR bits are updated. Depending on the value of the UPD_MR field, update is done before entering in self refresh mode or during a refresh command and a pending read or write access. • DS: Drive Strength Reset value is “0”. This field is unique to Low-power SDRAM. It selects the driver strength of SDRAM output. After the initialization sequence, as soon as DS field is modified, Extended Mode Register is accessed automatically and DS bits are updated. Depending on the value of the UPD_MR field, update is done before entering in self refresh mode or during a refresh command and a pending read or write access. • TIMEOUT: Low Power Mode Reset value is “00”. This field defines when low-power mode is enabled. 00 The SDRAM controller activates the SDRAM low-power mode immediately after the end of the last transfer. 01 The SDRAM controller activates the SDRAM low-power mode 64 clock cycles after the end of the last transfer. 10 The SDRAM controller activates the SDRAM low-power mode 128 clock cycles after the end of the last transfer. 11 Reserved • APDE: Active Power Down Exit Time Reset value is “1”. This mode is unique to DDR2-SDRAM devices. This mode allows to determine the active power-down mode, which determines performance versus power saving. 0: Fast Exit 1: Slow Exit After the initialization sequence, as soon as the APDE bit is modified, the Extended Mode Register, located in the memory of the external device, is accessed automatically and the APDE bit is updated. Depending on the value of the UPD_MR field, the update is done before entering in Self Refresh mode or during a refresh command and a pending read or write access. • UPD_MR: Update Load Mode Register and Extended Mode Register Reset value is “0”. This bit is used to enable or disable automatic update of the Load Mode Register and Extended Mode Register. This update depends on the DDRSDRC integration in a system. DDRSDRC can either share or not share an external bus with another controller. 00 Update is disabled. DDRSDRC shares external bus. Automatic update is done during a refresh command and a pending read or write 01 access in SDRAM device. 10 DDRSDRC does not share external bus. Automatic update is done before entering in self refresh mode. 11 Reserved 266 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.8.8 DDRSDRC Memory Device Register Name: DDRSDRC_MD Address: 0xFFFFE620 (0), 0xFFFFE420 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – DBW – MD This register can only be written if the bit WPEN is cleared in “DDRSDRC Write Protect Mode Register” on page 271. • MD: Memory Device Indicates the type of memory used. Reset value is for SDR-SDRAM device. 000: SDR-SDRAM 001: Low-power SDR-SDRAM 010: Reserved 011: Low-power DDR1-SDRAM 110: DDR2-SDRAM • DBW: Data Bus Width Reset value is 16 bits. 0: Data bus width is 32 bits (reserved for SDR-SDRAM device). 1: Data bus width is 16 bits. SAM9M11 [DATASHEET] 267 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.8.9 DDRSDRC DLL Register Name: DDRSDRC_DLL Address: 0xFFFFE624 (0), 0xFFFFE424 (1) Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 MDVAL 7 6 5 4 3 2 1 0 – – – – – MDOVF MDDEC MDINC The DLL logic is internally used by the controller in order to delay DQS inputs. This is necessary to center the strobe time and the data valid window. • MDINC: DLL Master Delay Increment 0: The DLL is not incrementing the Master delay counter. 1: The DLL is incrementing the Master delay counter. • MDDEC: DLL Master Delay Decrement 0: The DLL is not decrementing the Master delay counter. 1: The DLL is decrementing the Master delay counter. • MDOVF: DLL Master Delay Overflow Flag 0: The Master delay counter has not reached its maximum value, or the Master is not locked yet. 1: The Master delay counter has reached its maximum value, the Master delay counter increment is stopped and the DLL forces the Master lock. If this flag is set, it means the DDRSDRC clock frequency is too low compared to Master delay line number of elements. • MDVAL: DLL Master Delay Value Value of the Master delay counter. 268 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.8.10DDRSDRC High Speed Register Name: DDRSDRC_HS Address: 0xFFFFE62C (0), 0xFFFFE42C (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 DIS_ANTICIP_ – – – – – – – READ This register can only be written if the bit WPEN is cleared in “DDRSDRC Write Protect Mode Register” on page 271. • DIS_ANTICIP_READ: Anticip Read Access 0: Anticip read access is enabled. 1: Anticip read access is disabled (default). DIS_ANTICIP_READ allows DDR2 read access optimization with multi-port. As this feature is based on the “bank open policy”, the software must map different buffers in different DDR2 banks to take advantage of that feature. SAM9M11 [DATASHEET] 269 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.8.11 DDRSDRC DELAY I/O Register Name: DDRSDRC_DELAYx [x=1..4] Address: 0xFFFFE640 (0), 0xFFFFE440 (1) Access: Read/Write 31 30 29 28 27 26 25 24 DELAY8 DELAY7 23 22 21 20 19 18 17 16 DELAY6 DELAY5 15 14 13 12 11 10 9 8 DELAY4 DELAY3 7 6 5 4 3 2 1 0 DELAY2 DELAY1 • DELAYx: Delay1..Delay8 Gives the number of elements in the delay line. 270 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.8.12DDRSDRC Write Protect Mode Register Name: DDRSDRC_WPMR Address: 0xFFFFE6E4 (0), 0xFFFFE4E4 (1) Access: Read/Write 31 30 29 28 27 26 25 24 WPKEY 23 22 21 20 19 18 17 16 WPKEY 15 14 13 12 11 10 9 8 WPKEY 7 6 5 4 3 2 1 0 — — — — — — — WPEN • WPEN: Write Protect Enable 0: Disables the Write Protect if WPKEY corresponds to 0x444452 (“DDR” in ASCII). 1: Enables the Write Protect if WPKEY corresponds to 0x444452 (“DDR” in ASCII). Protects the registers: • “DDRSDRC Mode Register” on page 256 (cid:129) “DDRSDRC Refresh Timer Register” on page 257 (cid:129) “DDRSDRC Configuration Register” on page 258 (cid:129) “DDRSDRC Timing Parameter 0 Register” on page 261 (cid:129) “DDRSDRC Timing Parameter 1 Register” on page 263 (cid:129) “DDRSDRC Timing Parameter 2 Register” on page 264 (cid:129) “DDRSDRC Memory Device Register” on page 267 (cid:129) “DDRSDRC High Speed Register” on page 269 • WPKEY: Write Protect Key Should be written at value 0x444452 (“DDR” in ASCII). Writing any other value in this field aborts the write operation of the WPEN bit. Always reads as 0. SAM9M11 [DATASHEET] 271 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

21.8.13DDRSDRC Write Protect Status Register Name: DDRSDRC_WPSR Address: 0xFFFFE6E8 (0), 0xFFFFE4E8 (1) Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 WPVSRC 15 14 13 12 11 10 9 8 WPVSRC 7 6 5 4 3 2 1 0 – – – – – – – WPVS • WPVS: Write Protect Violation Status 0: No Write Protect Violation has occurred since the last read of the DDRSDRC_WPSR. 1: A Write Protect Violation has occurred since the last read of the DDRSDRC_WPSR. If this violation is an unauthorized attempt to write a protected register, the associated violation is reported into field WPVSRC. • WPVSRC: Write Protect Violation Source When WPVS is active, this field indicates the write-protected register (through address offset or code) in which a write access has been attempted. Note: Reading DDRSDRC_WPSR automatically clears all fields. 272 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22. Error Correction Code Controller (ECC) 22.1 Description NAND Flash/SmartMedia devices contain by default invalid blocks which have one or more invalid bits. Over the NAND Flash/SmartMedia lifetime, additional invalid blocks may occur which can be detected/corrected by ECC code. The ECC Controller is a mechanism that encodes data in a manner that makes possible the identification and correction of certain errors in data. The ECC controller is capable of single bit error correction and 2-bit random detection. When NAND Flash/SmartMedia have more than 2 bits of errors, the data cannot be corrected. The ECC user interface is compliant with the ARM Advanced Peripheral Bus (APB rev2). 22.2 Block Diagram Figure 22-1. Block Diagram NAND Flash Static Memory SmartMedia Controller Logic ECC Controller Ctrl/ECC Algorithm User Interface APB SAM9M11 [DATASHEET] 273 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.3 Functional Description A page in NAND Flash and SmartMedia memories contains an area for main data and an additional area used for redundancy (ECC). The page is organized in 8-bit or 16-bit words. The page size corresponds to the number of words in the main area plus the number of words in the extra area used for redundancy. Over time, some memory locations may fail to program or erase properly. In order to ensure that data is stored properly over the life of the NAND Flash device, NAND Flash providers recommend to utilize either 1 ECC per 256 bytes of data, 1 ECC per 512 bytes of data or 1 ECC for all of the page. The only configurations required for ECC are the NAND Flash or the SmartMedia page size (528/2112/4224) and the type of correction wanted (1 ECC for all the page/1 ECC per 256 bytes of data /1 ECC per 512 bytes of data). Page size is configured setting the PAGESIZE field in the ECC Mode Register (ECC_MR). Type of correction is configured setting the TYPECORRECT field in the ECC Mode Register (ECC_MR). ECC is automatically computed as soon as a read (00h)/write (80h) command to the NAND Flash or the SmartMedia is detected. Read and write access must start at a page boundary. ECC results are available as soon as the counter reaches the end of the main area. Values in the ECC Parity Registers (ECC_PR0 to ECC_PR15) are then valid and locked until a new start condition occurs (read/write command followed by address cycles). 22.3.1 Write Access Once the Flash memory page is written, the computed ECC codes are available in the ECC Parity (ECC_PR0 to ECC_PR15) registers. The ECC code values must be written by the software application in the extra area used for redundancy. The number of write accesses in the extra area is a function of the value of the type of correction field. For example, for 1 ECC per 256 bytes of data for a page of 512 bytes, only the values of ECC_PR0 and ECC_PR1 must be written by the software application. Other registers are meaningless. 22.3.2 Read Access After reading the whole data in the main area, the application must perform read accesses to the extra area where ECC code has been previously stored. Error detection is automatically performed by the ECC controller. Please note that it is mandatory to read consecutively the entire main area and the locations where Parity and NParity values have been previously stored to let the ECC controller perform error detection. The application can check the ECC Status Registers (ECC_SR1/ECC_SR2) for any detected errors. It is up to the application to correct any detected error. ECC computation can detect four different circumstances:  No error: XOR between the ECC computation and the ECC code stored at the end of the NAND Flash or SmartMedia page is equal to 0. No error flags in the ECC Status Registers (ECC_SR1/ECC_SR2).  Recoverable error: Only the RECERR flags in the ECC Status registers (ECC_SR1/ECC_SR2) are set. The corrupted word offset in the read page is defined by the WORDADDR field in the ECC Parity Registers (ECC_PR0 to ECC_PR15). The corrupted bit position in the concerned word is defined in the BITADDR field in the ECC Parity Registers (ECC_PR0 to ECC_PR15).  ECC error: The ECCERR flag in the ECC Status Registers (ECC_SR1/ECC_SR2) are set. An error has been detected in the ECC code stored in the Flash memory. The position of the corrupted bit can be found by the application performing an XOR between the Parity and the NParity contained in the ECC code stored in the Flash memory.  Non correctable error: The MULERR flag in the ECC Status Registers (ECC_SR1/ECC_SR2) are set. Several unrecoverable errors have been detected in the Flash memory page. ECC Status Registers, ECC Parity Registers are cleared when a read/write command is detected or a software reset is performed. 274 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

For Single-bit Error Correction and Double-bit Error Detection (SEC-DED) hsiao code is used. 24-bit ECC is generated in order to perform one bit correction per 256 or 512 bytes for pages of 512/2048/4096 8-bit words. 32- bit ECC is generated in order to perform one bit correction per 512/1024/2048/4096 8- or 16-bit words.They are generated according to the schemes shown in Figure 22-2 and Figure 22-3. Figure 22-2. Parity Generation for 512/1024/2048/4096 8-bit Words 1st byte Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 P8 P16 2nd byte Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 P8' PP3322 PX 3rd byte Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 P8 P16' 4 th byte Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 P8' (page size -3 )th byte Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 P8 P16 (page size -2 )th byte Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 P8' P32 PX' (page size -1 )th byte Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 P8 P16' Page size th byte Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 P8' P1 P1' P1 P1' P1 P1' P1 P1' P2 P2' P2 P2' P4 P4' Page size = 512 Px = 2048 P1=bit7(+)bit5(+)bit3(+)bit1(+)P1 Page size = 1024 Px = 4096 P2=bit7(+)bit6(+)bit3(+)bit2(+)P2 Page size = 2048 Px = 8192 P4=bit7(+)bit6(+)bit5(+)bit4(+)P4 Page size = 4096 Px = 16384 P1'=bit6(+)bit4(+)bit2(+)bit0(+)P1' P2'=bit5(+)bit4(+)bit1(+)bit0(+)P2' P4'=bit7(+)bit6(+)bit5(+)bit4(+)P4' To calculate P8’ to PX’ and P8 to PX, apply the algorithm that follows. Page size = 2n for i =0 to n begin for (j = 0 to page_size_byte) begin if(j[i] ==1) P[2i+3]=bit7(+)bit6(+)bit5(+)bit4(+)bit3(+) bit2(+)bit1(+)bit0(+)P[2i+3] else P[2i+3]’=bit7(+)bit6(+)bit5(+)bit4(+)bit3(+) bit2(+)bit1(+)bit0(+)P[2i+3]' end end SAM9M11 [DATASHEET] 275 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 22-3. Parity Generation for 512/1024/2048/4096 16-bit Words +)+) (( d d d d d d d d or or or or or or or or w w w w w w w w 1st 2nd 3rd 4th ze -3 )th ze -2 )th ze -1 )th e size th si si si g e e e Pa g g g a a a P P P ( ( ( 276 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

To calculate P8’ to PX’ and P8 to PX, apply the algorithm that follows. Page size = 2n for i =0 to n begin for (j = 0 to page_size_word) begin if(j[i] ==1) P[2i+3]= bit15(+)bit14(+)bit13(+)bit12(+) bit11(+)bit10(+)bit9(+)bit8(+) bit7(+)bit6(+)bit5(+)bit4(+)bit3(+) bit2(+)bit1(+)bit0(+)P[2n+3] else P[2i+3]’=bit15(+)bit14(+)bit13(+)bit12(+) bit11(+)bit10(+)bit9(+)bit8(+) bit7(+)bit6(+)bit5(+)bit4(+)bit3(+) bit2(+)bit1(+)bit0(+)P[2i+3]' end end SAM9M11 [DATASHEET] 277 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.4 Error Correction Code Controller (ECC) User Interface Table 22-1. Register Mapping Offset Register Name Access Reset 0x00 ECC Control Register ECC_CR Write-only – 0x04 ECC Mode Register ECC_MR Read/Write 0x0 0x08 ECC Status Register 1 ECC_SR1 Read-only 0x0 0x0C ECC Parity Register 0 ECC_PR0 Read-only 0x0 0x10 ECC Parity Register 1 ECC_PR1 Read-only 0x0 0x14 ECC Status Register 2 ECC_SR2 Read-only 0x0 0x18 ECC Parity 2 ECC_PR2 Read-only 0x0 0x1C ECC Parity 3 ECC_PR3 Read-only 0x0 0x20 ECC Parity 4 ECC_PR4 Read-only 0x0 0x24 ECC Parity 5 ECC_PR5 Read-only 0x0 0x28 ECC Parity 6 ECC_PR6 Read-only 0x0 0x2C ECC Parity 7 ECC_PR7 Read-only 0x0 0x30 ECC Parity 8 ECC_PR8 Read-only 0x0 0x34 ECC Parity 9 ECC_PR9 Read-only 0x0 0x38 ECC Parity 10 ECC_PR10 Read-only 0x0 0x3C ECC Parity 11 ECC_PR11 Read-only 0x0 0x40 ECC Parity 12 ECC_PR12 Read-only 0x0 0x44 ECC Parity 13 ECC_PR13 Read-only 0x0 0x48 ECC Parity 14 ECC_PR14 Read-only 0x0 0x4C ECC Parity 15 ECC_PR15 Read-only 0x0 0x14–0xFC Reserved – – – 278 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.4.1 ECC Control Register Name: ECC_CR Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – SRST RST • RST: RESET Parity Provides reset to current ECC by software. 1: Reset ECC Parity registers 0: No effect • SRST: Soft Reset Provides soft reset to ECC block 1: Resets all registers. 0: No effect. SAM9M11 [DATASHEET] 279 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.4.2 ECC Mode Register Name: ECC_MR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – TYPECORRECT – – PAGESIZE • PAGESIZE: Page Size This field defines the page size of the NAND Flash device. PAGESIZE Description 00 528 words 01 1056 words 10 2112 words 11 4224 words A word has a value of 8 bits or 16 bits, depending on the NAND Flash or SmartMedia memory organization. • TYPECORRECT: Type of Correction 00: 1 bit correction for a page size of 512/1024/2048/4096 bytes. 01: 1 bit correction for 256 bytes of data for a page size of 512/2048/4096 bytes. 10: 1 bit correction for 512 bytes of data for a page size of 512/2048/4096 bytes. 280 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.4.3 ECC Status Register 1 Name: ECC_SR1 Access: Read-only 31 30 29 28 27 26 25 24 – MULERR7 ECCERR7 RECERR7 – MULERR6 ECCERR6 RECERR6 23 22 21 20 19 18 17 16 – MULERR5 ECCERR5 RECERR5 – MULERR4 ECCERR4 RECERR4 15 14 13 12 11 10 9 8 – MULERR3 ECCERR3 RECERR3 – MULERR2 ECCERR2 RECERR2 7 6 5 4 3 2 1 0 – MULERR1 ECCERR1 RECERR1 – MULERR0 ECCERR0 RECERR0 • RECERR0: Recoverable Error 0: No Errors Detected. 1: Errors Detected. If MUL_ERROR is 0, a single correctable error was detected. Otherwise multiple uncorrected errors were detected. • ECCERR0: ECC Error 0: No Errors Detected. 1: A single bit error occurred in the ECC bytes. If TYPECORRECT = 0, read both ECC Parity 0 and ECC Parity 1 registers, the error occurred at the location which con- tains a 1 in the least significant 16 bits; else read ECC Parity 0 register, the error occurred at the location which contains a 1 in the least significant 24 bits. • MULERR0: Multiple Error 0: No Multiple Errors Detected. 1: Multiple Errors Detected. • RECERR1: Recoverable Error in the page between the 256th and the 511th bytes or the 512th and the 1023rd bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: Errors Detected. If MUL_ERROR is 0, a single correctable error was detected. Otherwise multiple uncorrected errors were detected. • ECCERR1: ECC Error in the page between the 256th and the 511th bytes or the 512th and the 1023rd bytes Fixed to 0 if TYPECORREC = 0 0: No Errors Detected. 1: A single bit error occurred in the ECC bytes. Read ECC Parity 1 register, the error occurred at the location which contains a 1 in the least significant 24 bits. • MULERR1: Multiple Error in the page between the 256th and the 511th bytes or the 512th and the 1023rd bytes Fixed to 0 if TYPECORREC = 0. 0: No Multiple Errors Detected. 1: Multiple Errors Detected. SAM9M11 [DATASHEET] 281 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• RECERR2: Recoverable Error in the page between the 512th and the 767th bytes or the 1024th and the 1535th bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: Errors Detected. If MUL_ERROR is 0, a single correctable error was detected. Otherwise, multiple uncorrected errors were detected. • ECCERR2: ECC Error in the page between the 512th and the 767th bytes or the 1024th and the 1535th bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: A single bit error occurred in the ECC bytes. Read ECC Parity 2 register, the error occurred at the location which contains a 1 in the least significant 24 bits. • MULERR2: Multiple Error in the page between the 512th and the 767th bytes or the 1024th and the 1535th bytes Fixed to 0 if TYPECORREC = 0. 0: No Multiple Errors Detected. 1: Multiple Errors Detected. • RECERR3: Recoverable Error in the page between the 768th and the 1023rd bytes or the 1536th and the 2047th bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: Errors Detected. If MUL_ERROR is 0, a single correctable error was detected. Otherwise multiple uncorrected errors were detected. • ECCERR3: ECC Error in the page between the 768th and the 1023rd bytes or the 1536th and the 2047th bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: A single bit error occurred in the ECC bytes. Read ECC Parity 3 register, the error occurred at the location which contains a 1 in the least significant 24 bits. • MULERR3: Multiple Error in the page between the 768th and the 1023rd bytes or the 1536th and the 2047th bytes Fixed to 0 if TYPECORREC = 0. 0: No Multiple Errors Detected. 1: Multiple Errors Detected. • RECERR4: Recoverable Error in the page between the 1024th and the 1279th bytes or the 2048th and the 2559th bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: Errors Detected. If MUL_ERROR is 0, a single correctable error was detected. Otherwise multiple uncorrected errors were detected. • ECCERR4: ECC Error in the page between the 1024th and the 1279th bytes or the 2048th and the 2559th bytes 282 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: A single bit error occurred in the ECC bytes. Read ECC Parity 4 register, the error occurred at the location which contains a 1 in the least significant 24 bits. • MULERR4: Multiple Error in the page between the 1024th and the 1279th bytes or the 2048th and the 2559th bytes Fixed to 0 if TYPECORREC = 0. 0: No Multiple Errors Detected. 1: Multiple Errors Detected. • RECERR5: Recoverable Error in the page between the 1280th and the 1535th bytes or the 2560th and the 3071st bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: Errors Detected. If MUL_ERROR is 0, a single correctable error was detected. Otherwise multiple uncorrected errors were detected • ECCERR5: ECC Error in the page between the 1280th and the 1535th bytes or the 2560th and the 3071st bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: A single bit error occurred in the ECC bytes. Read ECC Parity 5 register, the error occurred at the location which contains a 1 in the least significant 24 bits. • MULERR5: Multiple Error in the page between the 1280th and the 1535th bytes or the 2560th and the 3071st bytes Fixed to 0 if TYPECORREC = 0. 0: No Multiple Errors Detected. 1: Multiple Errors Detected. • RECERR6: Recoverable Error in the page between the 1536th and the 1791st bytes or the 3072nd and the 3583rd bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: Errors Detected. If MUL_ERROR is 0, a single correctable error was detected. Otherwise multiple uncorrected errors were detected. • ECCERR6: ECC Error in the page between the 1536th and the 1791st bytes or the 3072nd and the 3583rd bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: A single bit error occurred in the ECC bytes. Read ECC Parity 6 register, the error occurred at the location which contains a 1 in the least significant 24 bits. • MULERR6: Multiple Error in the page between the 1536th and the 1791st bytes or the 3072nd and the 3583rd bytes SAM9M11 [DATASHEET] 283 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Fixed to 0 if TYPECORREC = 0. 0: No Multiple Errors Detected. 1: Multiple Errors Detected. • RECERR7: Recoverable Error in the page between the 1792nd and the 2047th bytes or the 3584th and the 4095th bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: Errors Detected. If MUL_ERROR is 0, a single correctable error was detected. Otherwise, multiple uncorrected errors were detected. • ECCERR7: ECC Error in the page between the 1792nd and the 2047th bytes or the 3584th and the 4095th bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: A single bit error occurred in the ECC bytes. Read ECC Parity 7 register, the error occurred at the location which contains a 1 in the least significant 24 bits. • MULERR7: Multiple Error in the page between the 1792nd and the 2047th bytes or the 3584th and the 4095th bytes Fixed to 0 if TYPECORREC = 0. 0: No Multiple Errors Detected. 1: Multiple Errors Detected. 284 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.4.4 ECC Status Register 2 Name: ECC_SR2 Access: Read-only 31 30 29 28 27 26 25 24 – MULERR15 ECCERR15 RECERR15 – MULERR14 ECCERR14 RECERR14 23 22 21 20 19 18 17 16 – MULERR13 ECCERR13 RECERR13 – MULERR12 ECCERR12 RECERR12 15 14 13 12 11 10 9 8 – MULERR11 ECCERR11 RECERR11 – MULERR10 ECCERR10 RECERR10 7 6 5 4 3 2 1 0 – MULERR9 ECCERR9 RECERR9 – MULERR8 ECCERR8 RECERR8 • RECERR8: Recoverable Error in the page between the 2048th and the 2303rd bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: Errors Detected. If MUL_ERROR is 0, a single correctable error was detected. Otherwise multiple uncorrected errors were detected • ECCERR8: ECC Error in the page between the 2048th and the 2303rd bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: A single bit error occurred in the ECC bytes. Read ECC Parity 8 register, the error occurred at the location which contains a 1 in the least significant 24 bits. • MULERR8: Multiple Error in the page between the 2048th and the 2303rd bytes Fixed to 0 if TYPECORREC = 0. 0: No Multiple Errors Detected. 1: Multiple Errors Detected. • RECERR9: Recoverable Error in the page between the 2304th and the 2559th bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: Errors Detected. If MUL_ERROR is 0, a single correctable error was detected. Otherwise multiple uncorrected errors were detected. • ECCERR9: ECC Error in the page between the 2304th and the 2559th bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: A single bit error occurred in the ECC bytes. Read ECC Parity 9 register, the error occurred at the location which contains a 1 in the least significant 24 bits. SAM9M11 [DATASHEET] 285 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• MULERR9: Multiple Error in the page between the 2304th and the 2559th bytes Fixed to 0 if TYPECORREC = 0. 0: No Multiple Errors Detected. 1: Multiple Errors Detected. • RECERR10: Recoverable Error in the page between the 2560th and the 2815th bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: Errors Detected. If MUL_ERROR is 0, a single correctable error was detected. Otherwise, multiple uncorrected errors were detected. • ECCERR10: ECC Error in the page between the 2560th and the 2815th bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: A single bit error occurred in the ECC bytes. Read ECC Parity 10 register, the error occurred at the location which contains a 1 in the least significant 24 bits. • MULERR10: Multiple Error in the page between the 2560th and the 2815th bytes Fixed to 0 if TYPECORREC = 0. 0: No Multiple Errors Detected. 1: Multiple Errors Detected. • RECERR11: Recoverable Error in the page between the 2816th and the 3071st bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: Errors Detected. If MUL_ERROR is 0, a single correctable error was detected. Otherwise, multiple uncorrected errors were detected • ECCERR11: ECC Error in the page between the 2816th and the 3071st bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: A single bit error occurred in the ECC bytes. Read ECC Parity 11 register, the error occurred at the location which contains a 1 in the least significant 24 bits. • MULERR11: Multiple Error in the page between the 2816th and the 3071st bytes Fixed to 0 if TYPECORREC = 0. 0: No Multiple Errors Detected. 1: Multiple Errors Detected. • RECERR12: Recoverable Error in the page between the 3072nd and the 3327th bytes Fixed to 0 if TYPECORREC = 0 0: No Errors Detected 1: Errors Detected. If MUL_ERROR is 0, a single correctable error was detected. Otherwise multiple uncorrected errors were detected 286 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• ECCERR12: ECC Error in the page between the 3072nd and the 3327th bytes Fixed to 0 if TYPECORREC = 0 0: No Errors Detected 1: A single bit error occurred in the ECC bytes. Read ECC Parity 12 register, the error occurred at the location which contains a 1 in the least significant 24 bits. • MULERR12: Multiple Error in the page between the 3072nd and the 3327th bytes Fixed to 0 if TYPECORREC = 0. 0: No Multiple Errors Detected. 1: Multiple Errors Detected. • RECERR13: Recoverable Error in the page between the 3328th and the 3583rd bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: Errors Detected. If MUL_ERROR is 0, a single correctable error was detected. Otherwise multiple uncorrected errors were detected. • ECCERR13: ECC Error in the page between the 3328th and the 3583rd bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: A single bit error occurred in the ECC bytes. Read ECC Parity 13 register, the error occurred at the location which contains a 1 in the least significant 24 bits. • MULERR13: Multiple Error in the page between the 3328th and the 3583rd bytes Fixed to 0 if TYPECORREC = 0. 0: No Multiple Errors Detected. 1: Multiple Errors Detected. • RECERR14: Recoverable Error in the page between the 3584th and the 3839th bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: Errors Detected. If MUL_ERROR is 0, a single correctable error was detected. Otherwise, multiple uncorrected errors were detected. • ECCERR14: ECC Error in the page between the 3584th and the 3839th bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: A single bit error occurred in the ECC bytes. Read ECC Parity 14 register, the error occurred at the location which contains a 1 in the least significant 24 bits. • MULERR14: Multiple Error in the page between the 3584th and the 3839th bytes Fixed to 0 if TYPECORREC = 0. 0: No Multiple Errors Detected. 1: Multiple Errors Detected. SAM9M11 [DATASHEET] 287 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• RECERR15: Recoverable Error in the page between the 3840th and the 4095th bytes Fixed to 0 if TYPECORREC = 0. 0: No Errors Detected. 1: Errors Detected. If MUL_ERROR is 0, a single correctable error was detected. Otherwise, multiple uncorrected errors were detected • ECCERR15: ECC Error in the page between the 3840th and the 4095th bytes Fixed to 0 if TYPECORREC = 0 0: No Errors Detected. 1: A single bit error occurred in the ECC bytes. Read ECC Parity 15 register, the error occurred at the location which contains a 1 in the least significant 24 bits. • MULERR15: Multiple Error in the page between the 3840th and the 4095th bytes Fixed to 0 if TYPECORREC = 0. 0: No Multiple Errors Detected. 1: Multiple Errors Detected. 288 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.5 Registers for 1 ECC for a page of 512/1024/2048/4096 bytes 22.5.1 ECC Parity Register 0 Name: ECC_PR0 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 WORDADDR 7 6 5 4 3 2 1 0 WORDADDR BITADDR Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR: Bit Address During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR: Word Address During a page read, this value contains the word address (8-bit or 16-bit word depending on the memory plane organiza- tion) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. SAM9M11 [DATASHEET] 289 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.5.2 ECC Parity Register 1 Name: ECC_PR1 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 NPARITY 7 6 5 4 3 2 1 0 NPARITY • NPARITY Parity N 290 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.6 Registers for 1 ECC per 512 bytes for a page of 512/2048/4096 bytes, 8-bit word 22.6.1 ECC Parity Register 0 Name: ECC_PR0 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 NPARITY0 15 14 13 12 11 10 9 8 NPARITY0 WORDADD0 7 6 5 4 3 2 1 0 WORDADDR0 BITADDR0 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR0: corrupted Bit Address in the page between the first byte and the 511th bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR0: corrupted Word Address in the page between the first byte and the 511th bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY0 Parity N SAM9M11 [DATASHEET] 291 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.6.2 ECC Parity Register 1 Name: ECC_PR1 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 NPARITY1 15 14 13 12 11 10 9 8 NPARITY1 WORDADD1 7 6 5 4 3 2 1 0 WORDADDR1 BITADDR1 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR1: corrupted Bit Address in the page between the 512th and the 1023rd bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR1: corrupted Word Address in the page between the 512th and the 1023rd bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY1 Parity N 292 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.6.3 ECC Parity Register 2 Name: ECC_PR2 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 NPARITY2 15 14 13 12 11 10 9 8 NPARITY2 WORDADDR2 7 6 5 4 3 2 1 0 WORDADDR2 BITADDR2 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR2: corrupted Bit Address in the page between the 1023rd and the 1535th bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR2: corrupted Word Address in the page in the page between the 1023rd and the 1535th bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY2 Parity N SAM9M11 [DATASHEET] 293 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.6.4 ECC Parity Register 3 Name: ECC_PR3 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 NPARITY3 15 14 13 12 11 10 9 8 NPARITY3 WORDADDR3 7 6 5 4 3 2 1 0 WORDADDR3 BITADDR3 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR3: corrupted Bit Address in the page between the1536th and the 2047th bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR3 corrupted Word Address in the page between the 1536th and the 2047th bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY3 Parity N 294 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.6.5 ECC Parity Register 4 Name: ECC_PR4 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 NPARITY4 15 14 13 12 11 10 9 8 NPARITY4 WORDADDR4 7 6 5 4 3 2 1 0 WORDADDR4 BITADDR4 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR4: corrupted Bit Address in the page between the 2048th and the 2559th bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR4: corrupted Word Address in the page between the 2048th and the 2559th bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY4 Parity N SAM9M11 [DATASHEET] 295 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.6.6 ECC Parity Register 5 Name: ECC_PR5 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 NPARITY5 15 14 13 12 11 10 9 8 NPARITY5 WORDADDR5 7 6 5 4 3 2 1 0 WORDADDR5 BITADDR5 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR5: corrupted Bit Address in the page between the 2560th and the 3071st bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR5: corrupted Word Address in the page between the 2560th and the 3071st bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY5 Parity N 296 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.6.7 ECC Parity Register 6 Name: ECC_PR6 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 NPARITY6 15 14 13 12 11 10 9 8 NPARITY6 WORDADDR6 7 6 5 4 3 2 1 0 WORDADDR6 BITADDR6 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR6: corrupted Bit Address in the page between the 3072nd and the 3583rd bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR6: corrupted Word Address in the page between the 3072nd and the 3583rd bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY6 Parity N SAM9M11 [DATASHEET] 297 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.6.8 ECC Parity Register 7 Name: ECC_PR7 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 NPARITY7 15 14 13 12 11 10 9 8 NPARITY7 WORDADDR7 7 6 5 4 3 2 1 0 WORDADDR7 BITADDR7 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR7: corrupted Bit Address in the page between the 3584h and the 4095th bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR7: corrupted Word Address in the page between the 3584th and the 4095th bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY7 Parity N 298 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7 Registers for 1 ECC per 256 bytes for a page of 512/2048/4096 bytes, 8-bit word 22.7.1 ECC Parity Register 0 Name: ECC_PR0 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 0 NPARITY0 15 14 13 12 11 10 9 8 NPARITY0 0 WORDADDR0 7 6 5 4 3 2 1 0 WORDADDR0 BITADDR0 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR0: corrupted Bit Address in the page between the first byte and the 255th bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR0: corrupted Word Address in the page between the first byte and the 255th bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY0 Parity N SAM9M11 [DATASHEET] 299 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7.2 ECC Parity Register 1 Name: ECC_PR1 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 0 NPARITY1 15 14 13 12 11 10 9 8 NPARITY1 0 WORDADDR1 7 6 5 4 3 2 1 0 WORDADDR1 BITADDR1 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR1: corrupted Bit Address in the page between the 256th and the 511th bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR1: corrupted Word Address in the page between the 256th and the 511th bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY1 Parity N 300 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7.3 ECC Parity Register 2 Name: ECC_PR2 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 0 NPARITY2 15 14 13 12 11 10 9 8 NPARITY2 0 WORDADD2 7 6 5 4 3 2 1 0 WORDADDR2 BITADDR2 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR2: corrupted Bit Address in the page between the 512th and the 767th bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR2: corrupted Word Address in the page between the 512th and the 767th bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY2 Parity N SAM9M11 [DATASHEET] 301 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7.4 ECC Parity Register 3 Name: ECC_PR3 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 0 NPARITY3 15 14 13 12 11 10 9 8 NPARITY3 0 WORDADDR3 7 6 5 4 3 2 1 0 WORDADDR3 BITADDR3 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR3: corrupted Bit Address in the page between the 768th and the 1023rd bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR3: corrupted Word Address in the page between the 768th and the 1023rd bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless • NPARITY3 Parity N 302 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7.5 ECC Parity Register 4 Name: ECC_PR4 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 0 NPARITY4 15 14 13 12 11 10 9 8 NPARITY4 0 WORDADDR4 7 6 5 4 3 2 1 0 WORDADDR4 BITADDR4 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR4: corrupted bit address in the page between the 1024th and the 1279th bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR4: corrupted word address in the page between the 1024th and the 1279th bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY4 Parity N SAM9M11 [DATASHEET] 303 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7.6 ECC Parity Register 5 Name: ECC_PR5 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 0 NPARITY5 15 14 13 12 11 10 9 8 NPARITY5 0 WORDADDR5 7 6 5 4 3 2 1 0 WORDADDR5 BITADDR5 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR5: corrupted Bit Address in the page between the 1280th and the 1535th bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR5: corrupted Word Address in the page between the 1280th and the 1535th bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY5 Parity N 304 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7.7 ECC Parity Register 6 Name: ECC_PR6 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 0 NPARITY6 15 14 13 12 11 10 9 8 NPARITY6 0 WORDADDR6 7 6 5 4 3 2 1 0 WORDADDR6 BITADDR6 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR6: corrupted bit address in the page between the 1536th and the1791st bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR6: corrupted word address in the page between the 1536th and the1791st bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY6 Parity N SAM9M11 [DATASHEET] 305 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7.8 ECC Parity Register 7 Name: ECC_PR7 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 0 NPARITY7 15 14 13 12 11 10 9 8 NPARITY7 0 WORDADDR7 7 6 5 4 3 2 1 0 WORDADDR7 BITADDR7 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR7: corrupted Bit Address in the page between the 1792nd and the 2047th bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR7: corrupted Word Address in the page between the 1792nd and the 2047th bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY7 Parity N 306 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7.9 ECC Parity Register 8 Name: ECC_PR8 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 0 NPARITY8 15 14 13 12 11 10 9 8 NPARITY8 0 WORDADDR8 7 6 5 4 3 2 1 0 WORDADDR8 BITADDR8 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR8: corrupted Bit Address in the page between the 2048th and the2303rd bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR8: corrupted Word Address in the page between the 2048th and the 2303rd bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY8 Parity N. SAM9M11 [DATASHEET] 307 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7.10ECC Parity Register 9 Name: ECC_PR9 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 0 NPARITY9 15 14 13 12 11 10 9 8 NPARITY9 0 WORDADDR9 7 6 5 4 3 2 1 0 WORDADDR9 BITADDR9 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR9: corrupted bit address in the page between the 2304th and the 2559th bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR9: corrupted word address in the page between the 2304th and the 2559th bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless • NPARITY9 Parity N 308 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7.11 ECC Parity Register 10 Name: ECC_PR10 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 0 NPARITY10 15 14 13 12 11 10 9 8 NPARITY10 0 WORDADDR10 7 6 5 4 3 2 1 0 WORDADDR10 BITADDR10 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR10: corrupted Bit Address in the page between the 2560th and the2815th bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR10: corrupted Word Address in the page between the 2560th and the 2815th bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY10 Parity N SAM9M11 [DATASHEET] 309 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7.12ECC Parity Register 11 Name: ECC_PR11 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 0 NPARITY11 15 14 13 12 11 10 9 8 NPARITY11 0 WORDADDR11 7 6 5 4 3 2 1 0 WORDADDR11 BITADDR11 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR11: corrupted Bit Address in the page between the 2816th and the 3071st bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR11: corrupted Word Address in the page between the 2816th and the 3071st bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY11 Parity N 310 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7.13ECC Parity Register 12 Name: ECC_PR12 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 0 NPARITY12 15 14 13 12 11 10 9 8 NPARITY12 0 WORDADDR12 7 6 5 4 3 2 1 0 WORDADDR12 BITADDR12 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR12; corrupted Bit Address in the page between the 3072nd and the 3327th bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR12: corrupted Word Address in the page between the 3072nd and the 3327th bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY12 Parity N SAM9M11 [DATASHEET] 311 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7.14ECC Parity Register 13 Name: ECC_PR13 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 0 NPARITY13 15 14 13 12 11 10 9 8 NPARITY13 0 WORDADDR13 7 6 5 4 3 2 1 0 WORDADDR13 BITADDR13 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR13: corrupted Bit Address in the page between the 3328th and the 3583rd bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR13: corrupted Word Address in the page between the 3328th and the 3583rd bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY13 Parity N 312 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7.15ECC Parity Register 14 Name: ECC_PR14 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 0 NPARITY14 15 14 13 12 11 10 9 8 NPARITY14 0 WORDADDR14 7 6 5 4 3 2 1 0 WORDADDR14 BITADDR14 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR14: corrupted Bit Address in the page between the 3584th and the 3839th bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR14: corrupted Word Address in the page between the 3584th and the 3839th bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY14 Parity N SAM9M11 [DATASHEET] 313 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7.16ECC Parity Register 15 Name: ECC_PR15 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 0 NPARITY15 15 14 13 12 11 10 9 8 NPARITY15 0 WORDADDR15 7 6 5 4 3 2 1 0 WORDADDR15 BITADDR15 Once the entire main area of a page is written with data, the register content must be stored at any free location of the spare area. • BITADDR15: corrupted Bit Address in the page between the 3840th and the 4095th bytes During a page read, this value contains the corrupted bit offset where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • WORDADDR15: corrupted Word Address in the page between the 3840th and the 4095th bytes During a page read, this value contains the word address (8-bit word) where an error occurred, if a single error was detected. If multiple errors were detected, this value is meaningless. • NPARITY15 Parity N 314 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

23. Peripheral DMA Controller (PDC) 23.1 Description The Peripheral DMA Controller (PDC) transfers data between on-chip serial peripherals and the on- and/or off-chip memories. The link between the PDC and a serial peripheral is operated by the AHB to ABP bridge. The user interface of each PDC channel is integrated into the user interface of the peripheral it serves. The user interface of mono directional channels (receive only or transmit only), contains two 32-bit memory pointers and two 16-bit counters, one set (pointer, counter) for current transfer and one set (pointer, counter) for next transfer. The bi-directional channel user interface contains four 32-bit memory pointers and four 16-bit counters. Each set (pointer, counter) is used by current transmit, next transmit, current receive and next receive. Using the PDC removes processor overhead by reducing its intervention during the transfer. This significantly reduces the number of clock cycles required for a data transfer, which improves microcontroller performance. To launch a transfer, the peripheral triggers its associated PDC channels by using transmit and receive signals. When the programmed data is transferred, an end of transfer interrupt is generated by the peripheral itself. 23.2 Embedded Characteristics  Acting as one AHB Bus Matrix Master  Allows data transfers from/to peripheral to/from any memory space without any intervention of the processor.  Next Pointer support, prevents strong real-time constraints on buffer management. SAM9M11 [DATASHEET] 315 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The Peripheral DMA Controller handles transfer requests from the channel according to the following priorities (Low to High priorities): Table 23-1. Peripheral DMA Controller Instance name Channel T/R DBGU Transmit USART3 Transmit USART2 Transmit USART1 Transmit USART0 Transmit AC97C Transmit SPI1 Transmit SPI0 Transmit SSC1 Transmit SSC0 Transmit TSADCC Receive DBGU Receive USART3 Receive USART2 Receive USART1 Receive USART0 Receive AC97C Receive SPI1 Receive SPI0 Receive SSC1 Receive SSC0 Receive 316 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

23.3 Block Diagram Figure 23-1. Block Diagram FULL DUPLEX PDC PERIPHERAL THR PDC Channel A RHR PDC Channel B Status & Control Control HALF DUPLEX PERIPHERAL Control THR PDC Channel C RHR Status & Control Control RECEIVE or TRANSMIT PERIPHERAL RHR or THR PDC Channel D Status & Control Control SAM9M11 [DATASHEET] 317 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

23.4 Functional Description 23.4.1 Configuration The PDC channel user interface enables the user to configure and control data transfers for each channel. The user interface of each PDC channel is integrated into the associated peripheral user interface. The user interface of a serial peripheral, whether it is full or half duplex, contains four 32-bit pointers (RPR, RNPR, TPR, TNPR) and four 16-bit counter registers (RCR, RNCR, TCR, TNCR). However, the transmit and receive parts of each type are programmed differently: the transmit and receive parts of a full duplex peripheral can be programmed at the same time, whereas only one part (transmit or receive) of a half duplex peripheral can be programmed at a time. 32-bit pointers define the access location in memory for current and next transfer, whether it is for read (transmit) or write (receive). 16-bit counters define the size of current and next transfers. It is possible, at any moment, to read the number of transfers left for each channel. The PDC has dedicated status registers which indicate if the transfer is enabled or disabled for each channel. The status for each channel is located in the associated peripheral status register. Transfers can be enabled and/or disabled by setting TXTEN/TXTDIS and RXTEN/RXTDIS in the peripheral’s Transfer Control Register. At the end of a transfer, the PDC channel sends status flags to its associated peripheral. These flags are visible in the peripheral status register (ENDRX, ENDTX, RXBUFF, and TXBUFE). Refer to Section 23.4.3 and to the associated peripheral user interface. 23.4.2 Memory Pointers Each full duplex peripheral is connected to the PDC by a receive channel and a transmit channel. Both channels have 32-bit memory pointers that point respectively to a receive area and to a transmit area in on- and/or off-chip memory. Each half duplex peripheral is connected to the PDC by a bidirectional channel. This channel has two 32-bit memory pointers, one for current transfer and the other for next transfer. These pointers point to transmit or receive data depending on the operating mode of the peripheral. Depending on the type of transfer (byte, half-word or word), the memory pointer is incremented respectively by 1, 2 or 4 bytes. If a memory pointer address changes in the middle of a transfer, the PDC channel continues operating using the new address. 23.4.3 Transfer Counters Each channel has two 16-bit counters, one for current transfer and the other one for next transfer. These counters define the size of data to be transferred by the channel. The current transfer counter is decremented first as the data addressed by current memory pointer starts to be transferred. When the current transfer counter reaches zero, the channel checks its next transfer counter. If the value of next counter is zero, the channel stops transferring data and sets the appropriate flag. But if the next counter value is greater then zero, the values of the next pointer/next counter are copied into the current pointer/current counter and the channel resumes the transfer whereas next pointer/next counter get zero/zero as values. At the end of this transfer the PDC channel sets the appropriate flags in the Peripheral Status Register. The following list gives an overview of how status register flags behave depending on the counters’ values:  ENDRX flag is set when the PERIPH_RCR reaches zero.  RXBUFF flag is set when both PERIPH_RCR and PERIPH_RNCR reach zero.  ENDTX flag is set when the PERIPH_TCR reaches zero.  TXBUFE flag is set when both PERIPH_TCR and PERIPH_TNCR reach zero. 318 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

These status flags are described in the Peripheral Status Register. 23.4.4 Data Transfers The serial peripheral triggers its associated PDC channels’ transfers using transmit enable (TXEN) and receive enable (RXEN) flags in the transfer control register integrated in the peripheral’s user interface. When the peripheral receives an external data, it sends a Receive Ready signal to its PDC receive channel which then requests access to the Matrix. When access is granted, the PDC receive channel starts reading the peripheral Receive Holding Register (RHR). The read data are stored in an internal buffer and then written to memory. When the peripheral is about to send data, it sends a Transmit Ready to its PDC transmit channel which then requests access to the Matrix. When access is granted, the PDC transmit channel reads data from memory and puts them to Transmit Holding Register (THR) of its associated peripheral. The same peripheral sends data according to its mechanism. 23.4.5 PDC Flags and Peripheral Status Register Each peripheral connected to the PDC sends out receive ready and transmit ready flags and the PDC sends back flags to the peripheral. All these flags are only visible in the Peripheral Status Register. Depending on the type of peripheral, half or full duplex, the flags belong to either one single channel or two different channels. 23.4.5.1Receive Transfer End This flag is set when PERIPH_RCR reaches zero and the last data has been transferred to memory. It is reset by writing a non zero value in PERIPH_RCR or PERIPH_RNCR. 23.4.5.2Transmit Transfer End This flag is set when PERIPH_TCR reaches zero and the last data has been written into peripheral THR. It is reset by writing a non zero value in PERIPH_TCR or PERIPH_TNCR. 23.4.5.3Receive Buffer Full This flag is set when PERIPH_RCR reaches zero with PERIPH_RNCR also set to zero and the last data has been transferred to memory. It is reset by writing a non zero value in PERIPH_TCR or PERIPH_TNCR. 23.4.5.4Transmit Buffer Empty This flag is set when PERIPH_TCR reaches zero with PERIPH_TNCR also set to zero and the last data has been written into peripheral THR. It is reset by writing a non zero value in PERIPH_TCR or PERIPH_TNCR. SAM9M11 [DATASHEET] 319 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

23.5 Peripheral DMA Controller (PDC) User Interface Table 23-2. Register Mapping Offset Register Name(1) Access Reset 0x100 Receive Pointer Register PERIPH_RPR Read/Write 0 0x104 Receive Counter Register PERIPH_RCR Read/Write 0 0x108 Transmit Pointer Register PERIPH_TPR Read/Write 0 0x10C Transmit Counter Register PERIPH_TCR Read/Write 0 0x110 Receive Next Pointer Register PERIPH_RNPR Read/Write 0 0x114 Receive Next Counter Register PERIPH_RNCR Read/Write 0 0x118 Transmit Next Pointer Register PERIPH_TNPR Read/Write 0 0x11C Transmit Next Counter Register PERIPH_TNCR Read/Write 0 0x120 Transfer Control Register PERIPH_PTCR Write-only – 0x124 Transfer Status Register PERIPH_PTSR Read-only 0 Note: 1. PERIPH: Ten registers are mapped in the peripheral memory space at the same offset. These can be configured by the user according to the function and the desired peripheral. 320 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

23.5.1 Receive Pointer Register Name: PERIPH_RPR Access: Read/Write 31 30 29 28 27 26 25 24 RXPTR 23 22 21 20 19 18 17 16 RXPTR 15 14 13 12 11 10 9 8 RXPTR 7 6 5 4 3 2 1 0 RXPTR • RXPTR: Receive Pointer Register RXPTR must be set to receive buffer address. When a half duplex peripheral is connected to the PDC, RXPTR = TXPTR. SAM9M11 [DATASHEET] 321 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

23.5.2 Receive Counter Register Name: PERIPH_RCR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 RXCTR 7 6 5 4 3 2 1 0 RXCTR • RXCTR: Receive Counter Register RXCTR must be set to receive buffer size. When a half duplex peripheral is connected to the PDC, RXCTR = TXCTR. 0: Stops peripheral data transfer to the receiver 1–65535 = Starts peripheral data transfer if corresponding channel is active 322 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

23.5.3 Transmit Pointer Register Name: PERIPH_TPR Access: Read/Write 31 30 29 28 27 26 25 24 TXPTR 23 22 21 20 19 18 17 16 TXPTR 15 14 13 12 11 10 9 8 TXPTR 7 6 5 4 3 2 1 0 TXPTR • TXPTR: Transmit Counter Register TXPTR must be set to transmit buffer address. When a half duplex peripheral is connected to the PDC, RXPTR = TXPTR. SAM9M11 [DATASHEET] 323 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

23.5.4 Transmit Counter Register Name: PERIPH_TCR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 TXCTR 7 6 5 4 3 2 1 0 TXCTR • TXCTR: Transmit Counter Register TXCTR must be set to transmit buffer size. When a half duplex peripheral is connected to the PDC, RXCTR = TXCTR. 0: Stops peripheral data transfer to the transmitter 1–65535 = Starts peripheral data transfer if corresponding channel is active 324 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

23.5.5 Receive Next Pointer Register Name: PERIPH_RNPR Access: Read/Write 31 30 29 28 27 26 25 24 RXNPTR 23 22 21 20 19 18 17 16 RXNPTR 15 14 13 12 11 10 9 8 RXNPTR 7 6 5 4 3 2 1 0 RXNPTR • RXNPTR: Receive Next Pointer RXNPTR contains next receive buffer address. When a half duplex peripheral is connected to the PDC, RXNPTR = TXNPTR. SAM9M11 [DATASHEET] 325 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

23.5.6 Receive Next Counter Register Name: PERIPH_RNCR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 RXNCTR 7 6 5 4 3 2 1 0 RXNCTR • RXNCTR: Receive Next Counter RXNCTR contains next receive buffer size. When a half duplex peripheral is connected to the PDC, RXNCTR = TXNCTR. 326 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

23.5.7 Transmit Next Pointer Register Name: PERIPH_TNPR Access: Read/Write 31 30 29 28 27 26 25 24 TXNPTR 23 22 21 20 19 18 17 16 TXNPTR 15 14 13 12 11 10 9 8 TXNPTR 7 6 5 4 3 2 1 0 TXNPTR • TXNPTR: Transmit Next Pointer TXNPTR contains next transmit buffer address. When a half duplex peripheral is connected to the PDC, RXNPTR = TXNPTR. SAM9M11 [DATASHEET] 327 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

23.5.8 Transmit Next Counter Register Name: PERIPH_TNCR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 TXNCTR 7 6 5 4 3 2 1 0 TXNCTR • TXNCTR: Transmit Counter Next TXNCTR contains next transmit buffer size. When a half duplex peripheral is connected to the PDC, RXNCTR = TXNCTR. 328 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

23.5.9 Transfer Control Register Name: PERIPH_PTCR Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – TXTDIS TXTEN 7 6 5 4 3 2 1 0 – – – – – – RXTDIS RXTEN • RXTEN: Receiver Transfer Enable 0: No effect. 1: Enables PDC receiver channel requests if RXTDIS is not set. When a half duplex peripheral is connected to the PDC, enabling the receiver channel requests automatically disables the transmitter channel requests. It is forbidden to set both TXTEN and RXTEN for a half duplex peripheral. • RXTDIS: Receiver Transfer Disable 0: No effect. 1: Disables the PDC receiver channel requests. When a half duplex peripheral is connected to the PDC, disabling the receiver channel requests also disables the transmit- ter channel requests. • TXTEN: Transmitter Transfer Enable 0: No effect. 1: Enables the PDC transmitter channel requests. When a half duplex peripheral is connected to the PDC, it enables the transmitter channel requests only if RXTEN is not set. It is forbidden to set both TXTEN and RXTEN for a half duplex peripheral. • TXTDIS: Transmitter Transfer Disable 0: No effect. 1: Disables the PDC transmitter channel requests. When a half duplex peripheral is connected to the PDC, disabling the transmitter channel requests disables the receiver channel requests. SAM9M11 [DATASHEET] 329 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

23.5.10Transfer Status Register Name: PERIPH_PTSR Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – TXTEN 7 6 5 4 3 2 1 0 – – – – – – – RXTEN • RXTEN: Receiver Transfer Enable 0: PDC Receiver channel requests are disabled. 1: PDC Receiver channel requests are enabled. • TXTEN: Transmitter Transfer Enable 0: PDC Transmitter channel requests are disabled. 1: PDC Transmitter channel requests are enabled. 330 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

24. Clock Generator 24.1 Description The Clock Generator User Interface is embedded within the Power Management Controller Interface and is described in Section 25.12. However, the Clock Generator registers are named CKGR_. 24.2 Embedded Characteristics The Clock Generator is made up of:  One Low Power 32768 Hz Slow Clock Oscillator with bypass mode  One Low-Power RC oscillator  One 12 MHz Main Oscillator, which can be bypassed  One 400 to 800 MHz programmable PLLA, capable to provide the clock MCK to the processor and to the peripherals. This PLL has an input divider to offer a wider range of output frequencies from the 12 MHz input, the only limitation being the lowest input frequency shall be higher or equal to 2 MHz. The USB Device and Host HS Clocks are provided by a the dedicated UTMI PLL (UPLL) embedded in the UTMI macro. Figure 24-1. Clock Generator Block Diagram Clock Generator RCEN On Chip RC OSC Slow Clock SLCK XIN32 Slow Clock Oscillator XOUT32 OSCSEL OSC32EN OSC32BYP XIN 12M Main Main Clock Oscillator MAINCK XOUT UPLL UPLLCK PLLA and PLLA Clock Divider PLLACK Status Control Power Management Controller SAM9M11 [DATASHEET] 331 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

24.3 Slow Clock Crystal Oscillator The Clock Generator integrates a 32768 Hz low-power oscillator. The XIN32 and XOUT32 pins must be connected to a 32768 Hz crystal. Two external capacitors must be wired as shown in Figure 24-2. Figure 24-2. Typical Slow Clock Crystal Oscillator Connection XIN32 XOUT32 GNDOSC 32768 Hz Crystal 24.4 Slow Clock RC Oscillator The user has to take into account the possible drifts of the RC Oscillator. More details are given in Section 49.2 “DC Characteristics”. 24.5 Slow Clock Selection The slow clock can be generated either by an external 32768 Hz crystal or by the on-chip RC oscillator. The 32768Hz crystal oscillator can be bypassed by setting the bit OSC32BYP to accept an external slow clock on XIN32. The internal RC oscillator and the 32768 Hz oscillator can be enabled by setting to 1, respectively, RCEN bit and OSC32EN bit in the System Controller user interface. The OSCSEL command selects the slow clock source. Figure 24-3. Slow Clock Selection Clock Generator RCEN On Chip RC OSC Slow Clock SLCK XIN32 Slow Clock Oscillator XOUT32 OSCSEL OSC32EN OSC32BYP RCEN, OSC32EN,OSCSEL and OSC32BYP bits are located in the Slow Clock Controller Configuration Register (SCKCR) located at address 0xFFFFFD50 in the backed up part of the System Controller and so are preserved while VDDBU is present. After a VDDBU power on reset, the default configuration is RCEN = 1, OSC32EN = 0 and OSCSEL = 0, allowing the system to start on the internal RC oscillator. The programmer controls the slow clock switching by software and so must take precautions during the switching phase. 332 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

24.5.1 Switch from Internal RC Oscillator to the 32768 Hz Crystal To switch from internal RC oscillator to the 32768 Hz crystal, the programmer must execute the following sequence:  Switch the master clock to a source different from slow clock (PLLA or PLLB or Main Oscillator) through the Power management Controller.  Enable the 32768 Hz oscillator by setting the bit OSCEN to 1.  Wait 32768 Hz Startup Time for clock stabilization (software loop)  Switch from internal RC to 32768Hz by setting the bit OSCSEL to 1.  Wait 5 slow clock cycles for internal resynchronization  Disable the RC oscillator by setting the bit RCEN to 0. 24.5.2 Bypass the 32768 Hz Oscillator The following step must be added to bypass the 32768 Hz Oscillator.  An external clock must be connected on XIN32.  Enable the bypass path OSC32BYP bit set to 1.  Disable the 32768 Hz oscillator by setting the bit OSC32EN to 0. 24.5.3 Switch from 32768 Hz Crystal to the Internal RC oscillator The same procedure must be followed to switch from 32768 Hz crystal to the internal RC oscillator.  Switch the master clock to a source different from slow clock (PLLA or PLLB or Main Oscillator)  Enable the internal RC oscillator by setting the bit RCEN to 1.  Wait internal RC Startup Time for clock stabilization (software loop)  Switch from 32768 Hz oscillator to internal RC by setting the bit OSCSEL to 0  Wait 5 slow clock cycles for internal resynchronization  Disable the 32768 Hz oscillator by setting the bit OSC32EN to 0 SAM9M11 [DATASHEET] 333 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

24.5.4 Slow Clock Controller Configuration Register Name: SCKCR Address: 0xFFFFFD50 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – OSCSEL OSC32BYP OSC32EN RCEN • RCEN: Internal RC 0: RC is disabled 1: RC is enabled • OSC32EN: 32768 Hz Oscillator 0: 32768 Hz oscillator is disabled 1: 32768 Hz oscillator is enabled • OSC32BYP: 32768 Hz Oscillator Bypass 0: 32768 Hz oscillator is not bypassed 1: 32768 Hz oscillator is bypassed, accept an external slow clock on XIN32 • OSCSEL: Slow Clock Selector 0: Slow clock is internal RC 1: Slow clock is 32768 Hz oscillator 334 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

24.6 Main Oscillator The Main Oscillator is designed for a 12 MHz fundamental crystal. The 12 MHz is an input of the PLLA and the UPLL used to generate the 480 MHz USB High Speed Clock (UPLLCK). Figure 24-4 shows the Main Oscillator block diagram. Figure 24-4. Main Oscillator Block Diagram XIN 12M Main Main Clock Oscillator MAINCK XOUT UPLL UPLLCK PLLA and PLLA Clock Divider PLLACK 24.6.1 Main Oscillator Connections The typical crystal connection is illustrated in Figure 24-5. For further details on the electrical characteristics of the Main Oscillator, see Section 49.2 “DC Characteristics”. Figure 24-5. Typical Crystal Connection XIN XOUT GNDOSC 24.6.2 Main Oscillator Startup Time The startup time of the 12 MHz Main Oscillator is given in Section 49.2 “DC Characteristics”. 24.6.3 Main Oscillator Control To minimize the power required to start up the system, the main oscillator is disabled after reset and slow clock is selected. The software enables or disables the main oscillator so as to reduce power consumption by clearing the MOSCEN bit in the Main Oscillator Register (CKGR_MOR). When disabling the main oscillator by clearing the MOSCEN bit in CKGR_MOR, the MOSCS bit in PMC_SR is automatically cleared, indicating the main clock is off. When enabling the main oscillator, the user must initiate the main oscillator counter with a value corresponding to the startup time of the oscillator. This startup time depends on the crystal frequency connected to the main oscillator. When the MOSCEN bit and the OSCOUNT are written in CKGR_MOR to enable the main oscillator, the MOSCS bit in PMC_SR (Status Register) is cleared and the counter starts counting down on the slow clock divided by 8 SAM9M11 [DATASHEET] 335 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

from the OSCOUNT value. Since the OSCOUNT value is coded with 8 bits, the maximum startup time is about 62 ms. When the counter reaches 0, the MOSCS bit is set, indicating that the main clock is valid. Setting the MOSCS bit in PMC_IMR can trigger an interrupt to the processor. 24.6.4 Main Oscillator Bypass The user can input a clock on the device instead of connecting a crystal. In this case, the user has to provide the external clock signal on the XIN pin. The input characteristics of the XIN pin under these conditions are given in the product electrical characteristics section. The programmer has to be sure to set the OSCBYPASS bit to 1 and the MOSCEN bit to 0 in the Main OSC register (CKGR_MOR) for the external clock to operate properly. 24.7 Divider and PLLA Block The PLLA embeds an input divider to increase the accuracy of the resulting clock signals. However, the user must respect the PLLA minimum input frequency when programming the divider. The PLLA embeds also an output divisor by 2. Figure 24-6 shows the block diagram of the divider and PLLA block. Figure 24-6. Divider and PLLA Block Diagram DIVA MULA OUTA PLLADIV2 MAINCK Divider PLLA /1 or /2 PLLACK Divider PLLACOUNT PLLA SLCK LOCKA Counter 24.7.1 Divider and Phase Lock Loop Programming The divider can be set between 1 and 255 in steps of 1. When a divider field (DIV) is set to 0, the output of the corresponding divider and the PLL output is a continuous signal at level 0. On reset, each DIV field is set to 0, thus the corresponding PLL input clock is set to 0. The PLLA allows multiplication of the divider’s outputs. The PLLA clock signal has a frequency that depends on the respective source signal frequency and on the parameters DIVA and MULA. The factor applied to the source signal frequency is (MULA + 1)/DIVA. When MULA is written to 0, the PLLA is disabled and its power consumption is saved. Re-enabling the PLLA can be performed by writing a value higher than 0 in the MUL field. Whenever the PLLA is re-enabled or one of its parameters is changed, the LOCKA bit in PMC_SR is automatically cleared. The values written in the PLLACOUNT field in CKGR_PLLAR are loaded in the PLLA counter. The PLLA counter then decrements at the speed of the Slow Clock until it reaches 0. At this time, the LOCK bit is set in PMC_SR and can trigger an interrupt to the processor. The user has to load the number of Slow Clock cycles required to cover the PLLA transient time into the PLLACOUNT field. The PLLA clock can be divided by 2 by writing the PLLADIV2 bit in PMC_MCKR. 336 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

24.8 UTMI Bias and Phase Lock Loop Programming The multiplier is built-in to 40 to obtain the USB High Speed 480 MHz. UPLLEN MAINCK UPLL UPLLCK PLLCOUNT UPLL SLCK LOCKU Counter Whenever the UPLL is enabled by writing UPLLEN in CKGR_UCKR, the LOCKU bit in PMC_SR is automatically cleared. The values written in the PLLCOUNT field in CKGR_UCKR are loaded in the UPLL counter. The UPLL counter then decrements at the speed of the Slow Clock divided by 8 until it reaches 0. At this time, the LOCKU bit is set in PMC_SR and can trigger an interrupt to the processor. The user has to load the number of Slow Clock cycles required to cover the UPLL transient time into the PLLCOUNT field. The BIAS, needed for High Speed operations, is enabled by writing BIASEN in CKGR_UCKR once the PLL locked. SAM9M11 [DATASHEET] 337 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25. Power Management Controller (PMC) 25.1 Description The Power Management Controller (PMC) optimizes power consumption by controlling all system and user peripheral clocks. The PMC enables/disables the clock inputs to many of the peripherals and the ARM Processor. 25.2 Embedded Characteristics The Power Management Controller provides all the clock signals to the system. PMC input clocks:  UPLLCK: From UTMI PLL  PLLACK From PLLA  SLCK: slow clock from OSC32K or internal RC OSC  MAINCK: from 12 MHz external oscillator PMC output clocks  Processor Clock PCK  Master Clock MCK, in particular to the Matrix and the memory interfaces. The divider can be 1,2,3 or 4  DDR system clock equal to 2xMCK Note: DDR system clock is not available when Master Clock (MCK) equals Processor Clock (PCK).  USB Host EHCI High speed clock (UPLLCK)  USB OHCI clocks (UHP48M and UHP12M)  Independent peripheral clocks, typically at the frequency of MCK  Two programmable clock outputs: PCK0 and PCK1 This allows the software control of five flexible operating modes:  Normal Mode, processor and peripherals running at a programmable frequency  Idle Mode, processor stopped waiting for an interrupt  Slow Clock Mode, processor and peripherals running at low frequency  Standby Mode, mix of Idle and Backup Mode, peripheral running at low frequency, processor stopped waiting for an interrupt  Backup Mode, Main Power Supplies off, VDDBU powered by a battery 338 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.3 Block Diagram Figure 25-1. Power Management Controller Block Diagram PLLACK USBS USB UHP48M USBDIV+1 OHCI UHP12M /4 USB EHCI Processor PCK UPLLCK Clock Controller int Divider X /1 /1.5 /2 SysClk DDR Prescaler /1 /2 /3 /4 MCK MAINCK /1,/2,/4,.../64 SLCK Peripherals Master Clock Controller Clock Controller periph_clk[..] ON/OFF SLCK ON/OFF MAINCK Prescaler pck[..] /1,/2,/4,...,/64 UPLLCK Programmable Clock Controller 25.3.1 Main Application Modes The Power Management Controller provides three main application modes. 25.3.1.1 Normal Mode  PLLA and UPLL are running respectively at 400 MHz and 480 MHz  USB Device High Speed and Host EHCI High Speed operations are allowed  Full Speed OHCI input clock is UPLLCK, USBDIV is 9 (division by 10)  System Input clock is PLLACK, PCK is 400 MHz  MDIV is ‘11’, MCK is 133 MHz  DDR2 can be used at up to 133 MHz 25.3.1.2 USB HS and LPDDR Mode  Only UPLL is running at 480 MHz, PLLA power consumption is saved  USB Device High Speed and Host EHCI High Speed operations are allowed  Full Speed OHCI input clock is UPLLCK, USBDIV is 9 (division by 10)  System Input clock is UPLLCK, Prescaler is 2, PCK is 240 MHz  MDIV is ‘01’, MCK is 120 MHz  Only LPDDR can be used at up to 120 MHz SAM9M11 [DATASHEET] 339 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.3.1.3 No UDP HS, UHP FS and DDR2 Mode  Only PLLA is running at 384 MHz, UPLL power consumption is saved  USB Device High Speed and Host EHCI High Speed operations are NOT allowed  Full Speed OHCI input clock is PLLACK, USBDIV is 7 (division by 8)  System Input clock is PLLACK, PCK is 384 MHz  MDIV is ‘11’, MCK is 128 MHz  DDR2 can be used at up to 128 MHz 25.4 Master Clock Controller The Master Clock Controller provides selection and division of the Master Clock (MCK). MCK is the clock provided to all the peripherals and the memory controller. The Master Clock is selected from one of the clocks provided by the Clock Generator. Selecting the Slow Clock provides a Slow Clock signal to the whole device. Selecting the Main Clock saves power consumption of the PLLA. The Master Clock Controller is made up of a clock selector and a prescaler. It also contains a Master Clock divider which allows the processor clock to be faster than the Master Clock. The Master Clock selection is made by writing the CSS field (Clock Source Selection) in PMC_MCKR (Master Clock Register). The prescaler supports the division by a power of 2 of the selected clock between 1 and 64. The PRES field in PMC_MCKR programs the prescaler. The Master Clock divider can be programmed through the MDIV field in PMC_MCKR. Note: It is forbidden to modify MDIV and CSS at the same access. Each field must be modified separately with a wait for MCKRDY flag between the first field modification and the second field modification. Each time PMC_MCKR is written to define a new Master Clock, the MCKRDY bit is cleared in PMC_SR. It reads 0 until the Master Clock is established. Then, the MCKRDY bit is set and can trigger an interrupt to the processor. This feature is useful when switching from a high-speed clock to a lower one to inform the software when the change is actually done. Figure 25-2. Master Clock Controller PMC_MCKR PMC_MCKR CSS PRES PMC_MCKR MDIV SLCK Master MAINCK Master Clock Clock MCK Prescaler PLLACK Divider UPLLCK Processor To the Processor Clock Clock Controller (PCK) Divider 25.5 Processor Clock Controller The PMC features a Processor Clock Controller (PCK) that implements the Processor Idle Mode. The Processor Clock can be disabled by writing the System Clock Disable Register (PMC_SCDR). The status of this clock (at least for debug purpose) can be read in the System Clock Status Register (PMC_SCSR). The Processor Clock PCK is enabled after a reset and is automatically re-enabled by any enabled interrupt. The Processor Idle Mode is achieved by disabling the Processor Clock and entering Wait for Interrupt Mode. The Processor Clock is automatically re-enabled by any enabled fast or normal interrupt, or by reset of the product. 340 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Note: The ARM Wait for Interrupt mode is entered by means of CP15 coprocessor operation. Refer to the Atmel application note Optimizing Power Consumption of AT91SAM9261-based Systems, literature number 6217. When the Processor Clock is disabled, the current instruction is finished before the clock is stopped, but this does not prevent data transfers from other masters of the system bus. 25.6 USB Device and Host clocks The USB Device and Host High Speed ports clocks are controlled by the UDPHS and UHPHS bits in PMC_PCER. To save power on this peripheral when they are is not used, the user can set these bits in PMC_PCDR. The UDPHS and UHPHS bits PMC_PCSR gives the activity of these clocks. The PMC also provides the clocks UHP48M and UHP12M to the USB Host OHCI. The USB Host OHCI clocks are controlled by the UHP bit in PMC_SCER. To save power on this peripheral when it is not used, the user can set the UHP bit in PMC_SCDR. The UHP bit in PMC_SCSR gives the activity of this clock. The USB host OHCI requires both the 12/48 MHz signal and the Master Clock. USBDIV field in PMC_USB register is to be programmed to 9 (division by 10) for normal operations. To further reduce power consumption the user can stop UTMI PLL (in this case USB high-speed operations are not possible). Nevertheless, as the USB OHCI input clock (PLLA or UTMI PLL) can be selected with the USBS bit in the PMC_USB register, OHCI full-speed operation remains possible. The user must program the USB OHCI Input Clock and the USBDIV divider in the PMC_USB register to generate a 48MHz and a 12 MHz signal with an accuracy of ± 0.25%. 25.7 LPDDR/DDR2 Clock The Power Management Controller controls the clocks of the DDR memory. It provides SysClk DDR internal clock. That clock is used by the DDR Controller to provide DDR control, data and DDR clock signals. The DDR clock can be enabled and disabled with DDRCK bit respectively in PMC_SCER and PMC_SDER registers. At reset DDR clock is disabled to save power consumption. The Input clock is the same as Master Clock. The Output SysClk DDR Clock is 2xMCK. In the case MDIV = ‘00’, PCK = MCK and SysClk DDR and DDRCK clocks are not available. If Input clock is PLLACK/PLLADIV2, the DDR Controller can drive DDR2 and LPDDR at up to 133 MHz with MDIV= ‘11’. To save PLLA power consumption, the user can choose UPLLCK an Input clock for the system. In this case the DDR Controller can drive LPDDR at up to 120 MHz. 25.8 Peripheral Clock Controller The Power Management Controller controls the clocks of each embedded peripheral by the way of the Peripheral Clock Controller. The user can individually enable and disable the Master Clock on the peripherals by writing into the Peripheral Clock Enable (PMC_PCER) and Peripheral Clock Disable (PMC_PCDR) registers. The status of the peripheral clock activity can be read in the Peripheral Clock Status Register (PMC_PCSR). When a peripheral clock is disabled, the clock is immediately stopped. The peripheral clocks are automatically disabled after a reset. In order to stop a peripheral, it is recommended that the system software wait until the peripheral has executed its last programmed operation before disabling the clock. This is to avoid data corruption or erroneous behavior of the system. SAM9M11 [DATASHEET] 341 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The bit number within the Peripheral Clock Control registers (PMC_PCER, PMC_PCDR, and PMC_PCSR) is the Peripheral Identifier defined at the product level. Generally, the bit number corresponds to the interrupt source number assigned to the peripheral. 25.9 Programmable Clock Output Controller The PMC controls two signals to be output on external pins PCKx. Each signal can be independently programmed via the PMC_PCKx registers. PCKx can be independently selected between the Slow clock, the Master Clock, the PLLACK/PLLADIV2, the UTMI PLL output and the main clock by writing the CSS and CSSMCK fields in PMC_PCKx. Each output signal can also be divided by a power of 2 between 1 and 64 by writing the PRES (Prescaler) field in PMC_PCKx. Each output signal can be enabled and disabled by writing 1 in the corresponding bit, PCKx of PMC_SCER and PMC_SCDR, respectively. Status of the active programmable output clocks are given in the PCKx bits of PMC_SCSR (System Clock Status Register). Moreover, like the PCK, a status bit in PMC_SR indicates that the Programmable Clock is actually what has been programmed in the Programmable Clock registers. As the Programmable Clock Controller does not manage with glitch prevention when switching clocks, it is strongly recommended to disable the Programmable Clock before any configuration change and to re-enable it after the change is actually performed. 25.10 Programming Sequence 1. Enabling the 12 MHz Main Oscillator: The main oscillator is enabled by setting the MOSCEN field in the CKGR_MOR. In some cases it may be advantageous to define a start-up time. This can be achieved by writing a value in the OSCOUNT field in the CKGR_MOR. Once this register has been correctly configured, the user must wait for MOSCS field in the PMC_SR to be set. This can be done either by polling the status register or by waiting the interrupt line to be raised if the associated interrupt to MOSCS has been enabled in the PMC_IER. 2. Setting PLLA and divider: All parameters needed to configure PLLA and the divider are located in the CKGR_PLLAR. The DIVA field is used to control divider itself. A value between 0 and 255 can be programmed. Divider output is divider input divided by DIVA parameter. By default DIVA parameter is set to 0 which means that divider is turned off. The OUTA field is used to select the PLLA output frequency range. The MULA field is the PLLA multiplier factor. This parameter can be programmed between 0 and 254. If MULA is set to 0, PLLA will be turned off, otherwise the PLLA output frequency is PLLA input frequency multiplied by (MULA + 1). The PLLACOUNT field specifies the number of slow clock cycles before LOCKA bit is set in the PMC_SR after CKGR_PLLAR has been written. Once the PMC_PLLAR has been written, the user must wait for the LOCKA bit to be set in the PMC_SR. This can be done either by polling the status register or by waiting the interrupt line to be raised if the associated interrupt to LOCKA has been enabled in the PMC_IER. All parameters in CKGR_PLLAR can be programmed in a single write operation. If at some stage one of the following parameters, MULA, DIVA is modified, LOCKA bit will go low to indicate that PLLA is not ready yet. When PLLA is locked, LOCKA will be set again. The user is constrained to wait for LOCKA bit to be set before using the PLLA output clock. 342 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Code Example: write_register(CKGR_PLLAR,0x00040805) If PLLA and divider are enabled, the PLLA input clock is the main clock. PLLA output clock is PLLA input clock multiplied by 5. Once CKGR_PLLAR has been written, LOCKA bit will be set after eight slow clock cycles. 3. Setting Bias and High Speed PLL (UPLL) for UTMI The UTMI PLL is enabled by setting the UPLLEN field in the CKGR_UCKR. The UTMI Bias must is enabled by setting the BIASEN field in the CKGR_UCKR in the same time. In some cases it may be advantageous to define a start-up time. This can be achieved by writing a value in the PLLCOUNT field in the CKGR_UCKR. Once this register has been correctly configured, the user must wait for LOCKU field in the PMC_SR to be set. This can be done either by polling the status register or by waiting the interrupt line to be raised if the associated interrupt to LOCKU has been enabled in the PMC_IER. 4. Selection of Master Clock and Processor Clock The Master Clock and the Processor Clock are configurable via the PMC_MCKR. The CSS field is used to select the clock source of the Master Clock and Processor Clock dividers. By default, the selected clock source is slow clock. The PRES field is used to control the Master/Processor Clock prescaler. The user can choose between different values (1, 2, 4, 8, 16, 32, 64). Prescaler output is the selected clock source divided by PRES parameter. By default, PRES parameter is set to 1 which means that the input clock of the Master Clock and Processor Clock dividers is equal to slow clock. The MDIV field is used to control the Master Clock divider. It is possible to choose between different values (0, 1, 2, 3). The Master Clock output is Master/Processor Clock Prescaler output divided by 1, 2, 4 or 3, depending on the value programmed in MDIV. The PLLADIV2 field is used to control the PLLA Clock divider. It is possible to choose between different values (0, 1). The PMC PLLA Clock input is divided by 1 or 2, depending on the value programmed in PLLADIV2. By default, MDIV and PLLLADIV2 are set to 0, which indicates that Processor Clock is equal to the Master Clock. Once the PMC_MCKR has been written, the user must wait for the MCKRDY bit to be set in the PMC_SR. This can be done either by polling the status register or by waiting for the interrupt line to be raised if the associated interrupt to MCKRDY has been enabled in the PMC_IER. The PMC_MCKR must not be programmed in a single write operation. The preferred programming sequence for the PMC_MCKR is as follows:  If a new value for CSS field corresponds to PLLA Clock, ̶ Program the PRES field in the PMC_MCKR. ̶ Wait for the MCKRDY bit to be set in the PMC_SR. ̶ Program the CSS field in the PMC_MCKR. ̶ Wait for the MCKRDY bit to be set in the PMC_SR.  If a new value for CSS field corresponds to Main Clock or Slow Clock, ̶ Program the CSS field in the PMC_MCKR. ̶ Wait for the MCKRDY bit to be set in the PMC_SR. ̶ Program the PRES field in the PMC_MCKR. ̶ Wait for the MCKRDY bit to be set in the PMC_SR. SAM9M11 [DATASHEET] 343 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

If at some stage one of the following parameters, CSS or PRES, is modified, the MCKRDY bit will go low to indicate that the Master Clock and the Processor Clock are not ready yet. The user must wait for MCKRDY bit to be set again before using the Master and Processor Clocks. Note: IF PLLA clock was selected as the Master Clock and the user decides to modify it by writing in CKGR_PLLAR, the MCKRDY flag will go low while PLLA is unlocked. Once PLLA is locked again, LOCK goes high and MCKRDY is set. While PLLA is unlocked, the Master Clock selection is automatically changed to Main Clock. For further information, see Section 25.11.2. “Clock Switching Waveforms” on page 346. Code Example: write_register(PMC_MCKR,0x00000001) wait (MCKRDY=1) write_register(PMC_MCKR,0x00000011) wait (MCKRDY=1) The Master Clock is main clock divided by 16. The Processor Clock is the Master Clock. 5. Selection of Programmable clocks Programmable clocks are controlled via registers; PMC_SCER, PMC_SCDR and PMC_SCSR. Programmable clocks can be enabled and/or disabled via the PMC_SCER and PMC_SCDRs. Depending on the system used, two programmable clocks can be enabled or disabled. The PMC_SCSR provides a clear indication as to which Programmable clock is enabled. By default all Programmable clocks are disabled. PMC_PCKx registers are used to configure programmable clocks. The CSS and CSSMCK fields are used to select the programmable clock divider source. Five clock options are available: main clock, slow clock, master clock, PLLACK, UPLLCK. By default, the clock source selected is slow clock. The PRES field is used to control the programmable clock prescaler. It is possible to choose between different values (1, 2, 4, 8, 16, 32, 64). Programmable clock output is prescaler input divided by PRES parameter. By default, the PRES parameter is set to 1 which means that master clock is equal to slow clock. Once the PMC_PCKx register has been programmed, The corresponding programmable clock must be enabled and the user is constrained to wait for the PCKRDYx bit to be set in the PMC_SR. This can be done either by polling the status register or by waiting the interrupt line to be raised if the associated interrupt to PCKRDYx has been enabled in the PMC_IER. All parameters in PMC_PCKx can be programmed in a single write operation. If the CSS and PRES parameters are to be modified, the corresponding programmable clock must be disabled first. The parameters can then be modified. Once this has been done, the user must re-enable the programmable clock and wait for the PCKRDYx bit to be set. Code Example: write_register(PMC_PCK0,0x00000015) Programmable clock 0 is main clock divided by 32. 6. Enabling Peripheral Clocks Once all of the previous steps have been completed, the peripheral clocks can be enabled and/or disabled via registers PMC_PCER and PMC_PCDR. 344 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Depending on the system used, 19 peripheral clocks can be enabled or disabled. The PMC_PCSR provides a clear view as to which peripheral clock is enabled. Note: Each enabled peripheral clock corresponds to Master Clock. Code Examples: write_register(PMC_PCER,0x00000110) Peripheral clocks 4 and 8 are enabled. write_register(PMC_PCDR,0x00000010) Peripheral clock 4 is disabled. 25.11 Clock Switching Details 25.11.1 Master Clock Switching Timings Table 25-1 gives the worst case timings required for the Master Clock to switch from one selected clock to another one. This is in the event that the prescaler is de-activated. When the prescaler is activated, an additional time of 64 clock cycles of the new selected clock has to be added. Table 25-1. Clock Switching Timings (Worst Case) From Main Clock SLCK PLLA Clock To 3 x PLLA Clock + 4 x SLCK + Main Clock – 4 x SLCK + 2.5 x Main Clock 1 x Main Clock 0.5 x Main Clock + 3 x PLLA Clock + SLCK – 4.5 x SLCK 5 x SLCK 0.5 x Main Clock + 2.5 x PLLA Clock + 2.5 x PLLA Clock + 4 x SLCK + PLLA Clock 5 x SLCK + 4 x SLCK + PLLACOUNT x SLCK + PLLACOUNT x SLCK PLLACOUNT x SLCK 2.5 x PLLAx Clock SAM9M11 [DATASHEET] 345 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.11.2 Clock Switching Waveforms Figure 25-3. Switch Master Clock from Slow Clock to PLLA Clock Slow Clock PLL Clock LOCK MCKRDY Master Clock Write PMC_MCKR Figure 25-4. Switch Master Clock from Main Clock to Slow Clock Slow Clock Main Clock MCKRDY Master Clock Write PMC_MCKR 346 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 25-5. Change PLLA Programming Main Clock PLL Clock LOCK MCKRDY Master Clock Main Clock Write CKGR_PLLR Figure 25-6. Programmable Clock Output Programming PLL Clock PCKRDY PCKx Output Write PMC_PCKx PLL Clock is selected Write PMC_SCER PCKx is enabled Write PMC_SCDR PCKx is disabled SAM9M11 [DATASHEET] 347 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12 Power Management Controller (PMC) User Interface Table 25-2. Register Mapping Offset Register Name Access Reset Value 0x0000 System Clock Enable Register PMC_SCER Write-only – 0x0004 System Clock Disable Register PMC_SCDR Write-only – 0x0008 System Clock Status Register PMC _SCSR Read-only 0x01 0x000C Reserved – – – 0x0010 Peripheral Clock Enable Register PMC _PCER Write-only – 0x0014 Peripheral Clock Disable Register PMC_PCDR Write-only – 0x0018 Peripheral Clock Status Register PMC_PCSR Read-only 0x0 0x001C UTMI Clock Configuration Register CKGR_UCKR Read/Write 0x1020 0800 0x0020 Main Oscillator Register CKGR_MOR Read/Write 0x0 0x0024 Main Clock Frequency Register CKGR_MCFR Read-only 0x0 0x0028 PLLA Register CKGR_PLLAR Read/Write 0x3F00 0x002C Reserved – – – 0x0030 Master Clock Register PMC_MCKR Read/Write 0x0 0x0038 USB Clock Register PMC_USB Read/Write 0x0 0x003C Reserved – – – 0x0040 Programmable Clock 0 Register PMC_PCK0 Read/Write 0x0 0x0044 Programmable Clock 1 Register PMC_PCK1 Read/Write 0x0 0x0048–0x005C Reserved – – – 0x0060 Interrupt Enable Register PMC_IER Write-only – 0x0064 Interrupt Disable Register PMC_IDR Write-only – 0x0068 Status Register PMC_SR Read-only 0x08 0x006C Interrupt Mask Register PMC_IMR Read-only 0x0 0x0070–0x007C Reserved – – – 0x0080 PLL Charge Pump Current Register PMC_PLLICPR Read/Write 0x0 348 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.1 PMC System Clock Enable Register Name: PMC_SCER Address: 0xFFFFFC00 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 PCK7 PCK6 PCK5 PCK4 PCK5 PCK4 PCK1 PCK0 7 6 5 4 3 2 1 0 PCK7 UHP – – – DDRCK – – • DDRCK: DDR Clock Enable 0: No effect. 1: Enables the DDR clock. • UHP: USB Host OHCI Clocks Enable 0: No effect. 1: Enables the UHP48M and UHP12M OHCI clocks. • PCKx: Programmable Clock x Output Enable 0: No effect. 1: Enables the corresponding Programmable Clock output. SAM9M11 [DATASHEET] 349 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.2 PMC System Clock Disable Register Name: PMC_SCDR Address: 0xFFFFFC04 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 PCK7 PCK6 PCK5 PCK4 PCK5 PCK4 PCK1 PCK0 7 6 5 4 3 2 1 0 PCK7 UHP – – – DDRCK – PCK • PCK: Processor Clock Disable 0: No effect. 1: Disables the Processor clock. This is used to enter the processor in Idle Mode. • DDRCK: DDR Clock Disable 0: No effect. 1: Disables the DDR clock. • UHP: USB Host OHCI Clock Disable 0: No effect. 1: Disables the UHP48M and UHP12M OHCI clocks. • PCKx: Programmable Clock x Output Disable 0: No effect. 1: Disables the corresponding Programmable Clock output. 350 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.3 PMC System Clock Status Register Name: PMC_SCSR Address: 0xFFFFFC08 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 PCK7 PCK6 PCK5 PCK4 PCK5 PCK4 PCK1 PCK0 7 6 5 4 3 2 1 0 PCK7 UHP – – – DDRCK – PCK • PCK: Processor Clock Status 0: The Processor clock is disabled. 1: The Processor clock is enabled. • DDRCK: DDR Clock Status 0: The DDR clock is disabled. 1: The DDR clock is enabled. • UHP: USB Host Port Clock Status 0: The UHP48M and UHP12M OHCI clocks are disabled. 1: The UHP48M and UHP12M OHCI clocks are enabled. • PCKx: Programmable Clock x Output Status 0: The corresponding Programmable Clock output is disabled. 1: The corresponding Programmable Clock output is enabled. SAM9M11 [DATASHEET] 351 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.4 PMC Peripheral Clock Enable Register Name: PMC_PCER Address: 0xFFFFFC10 Access: Write-only 31 30 29 28 27 26 25 24 PID31 PID30 PID29 PID28 PID27 PID26 PID25 PID24 23 22 21 20 19 18 17 16 PID23 PID22 PID21 PID20 PID19 PID18 PID17 PID16 15 14 13 12 11 10 9 8 PID15 PID14 PID13 PID12 PID11 PID10 PID9 PID8 7 6 5 4 3 2 1 0 PID7 PID6 PID5 PID4 PID3 PID2 - - • PIDx: Peripheral Clock x Enable 0: No effect. 1: Enables the corresponding peripheral clock. Note: PID2 to PID31 refer to identifiers as defined in the section “Peripheral Identifiers” in the product datasheet. Note: Programming the control bits of the Peripheral ID that are not implemented has no effect on the behavior of the PMC. 352 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.5 PMC Peripheral Clock Disable Register Name: PMC_PCDR Address: 0xFFFFFC14 Access: Write-only 31 30 29 28 27 26 25 24 PID31 PID30 PID29 PID28 PID27 PID26 PID25 PID24 23 22 21 20 19 18 17 16 PID23 PID22 PID21 PID20 PID19 PID18 PID17 PID16 15 14 13 12 11 10 9 8 PID15 PID14 PID13 PID12 PID11 PID10 PID9 PID8 7 6 5 4 3 2 1 0 PID7 PID6 PID5 PID4 PID3 PID2 - - • PIDx: Peripheral Clock x Disable 0: No effect. 1: Disables the corresponding peripheral clock. Note: PID2 to PID31 refer to identifiers as defined in the section “Peripheral Identifiers” in the product datasheet. SAM9M11 [DATASHEET] 353 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.6 PMC Peripheral Clock Status Register Name: PMC_PCSR Address: 0xFFFFFC18 Access: Read-only 31 30 29 28 27 26 25 24 PID31 PID30 PID29 PID28 PID27 PID26 PID25 PID24 23 22 21 20 19 18 17 16 PID23 PID22 PID21 PID20 PID19 PID18 PID17 PID16 15 14 13 12 11 10 9 8 PID15 PID14 PID13 PID12 PID11 PID10 PID9 PID8 7 6 5 4 3 2 1 0 PID7 PID6 PID5 PID4 PID3 PID2 – – • PIDx: Peripheral Clock x Status 0: The corresponding peripheral clock is disabled. 1: The corresponding peripheral clock is enabled. Note: PID2 to PID31 refer to identifiers as defined in the section “Peripheral Identifiers” in the product datasheet. 354 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.7 PMC UTMI Clock Configuration Register Name: CKGR_UCKR Address: 0xFFFFFC1C Access: Read/Write 31 30 29 28 27 26 25 24 BIASCOUNT – – – BIASEN 23 22 21 20 19 18 17 16 PLLCOUNT – – – UPLLEN 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – – • UPLLEN: UTMI PLL Enable 0: The UTMI PLL is disabled. 1: The UTMI PLL is enabled. When UPLLEN is set, the LOCKU flag is set once the UTMI PLL startup time is achieved. • PLLCOUNT: UTMI PLL Start-up Time Specifies the number of Slow Clock cycles multiplied by 8 for the UTMI PLL start-up time. • BIASEN: UTMI BIAS Enable 0: The UTMI BIAS is disabled. 1: The UTMI BIAS is enabled. • BIASCOUNT: UTMI BIAS Start-up Time Specifies the number of Slow Clock cycles for the UTMI BIAS start-up time. SAM9M11 [DATASHEET] 355 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.8 PMC Clock Generator Main Oscillator Register Name: CKGR_MOR Address: 0xFFFFFC20 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 OSCOUNT 7 6 5 4 3 2 1 0 – – – – – – OSCBYPASS MOSCEN • MOSCEN: Main Oscillator Enable A crystal must be connected between XIN and XOUT. 0: The Main Oscillator is disabled. 1: The Main Oscillator is enabled. OSCBYPASS must be set to 0. When MOSCEN is set, the MOSCS flag is set once the Main Oscillator startup time is achieved. • OSCBYPASS: Oscillator Bypass 0: No effect. 1: The Main Oscillator is bypassed. MOSCEN must be set to 0. An external clock must be connected on XIN. When OSCBYPASS is set, the MOSCS flag in PMC_SR is automatically set. Clearing MOSCEN and OSCBYPASS bits allows resetting the MOSCS flag. • OSCOUNT: Main Oscillator Start-up Time Specifies the number of Slow Clock cycles multiplied by 8 for the Main Oscillator start-up time. 356 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.9 PMC Clock Generator Main Clock Frequency Register Name: CKGR_MCFR Address: 0xFFFFFC24 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – MAINRDY 15 14 13 12 11 10 9 8 MAINF 7 6 5 4 3 2 1 0 MAINF • MAINF: Main Clock Frequency Gives the number of Main Clock cycles within 16 Slow Clock periods. • MAINRDY: Main Clock Ready 0: MAINF value is not valid or the Main Oscillator is disabled. 1: The Main Oscillator has been enabled previously and MAINF value is available. SAM9M11 [DATASHEET] 357 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.10 PMC Clock Generator PLLA Register Name: CKGR_PLLAR Address: 0xFFFFFC28 Access: Read/Write 31 30 29 28 27 26 25 24 – – 1 – – – – – 23 22 21 20 19 18 17 16 MULA 15 14 13 12 11 10 9 8 OUTA PLLACOUNT 7 6 5 4 3 2 1 0 DIVA Possible limitations on PLL input frequencies and multiplier factors should be checked before using the PMC. Warning: Bit 29 must always be set to 1 when programming the CKGR_PLLAR. • DIVA: Divider A DIVA Divider Selected 0 Divider output is 0 1 Divider is bypassed 2–255 Divider output is the selected clock divided by DIVA. • PLLACOUNT: PLLA Counter Specifies the number of slow clock cycles before the LOCKA bit is set in PMC_SR after CKGR_PLLAR is written. • OUTA: PLLA Clock Frequency Range To optimize clock performance, this field must be programmed as specified in “PLL Characteristics” in the Electrical Char- acteristics section of the product datasheet. • MULA: PLLA Multiplier 0: The PLLA is deactivated. 1–254 = The PLLA Clock frequency is the PLLA input frequency multiplied by MULA+ 1. 358 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.11 PMC USB Clock Register Name: PMC_USB Address: 0xFFFFFC38 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – USBDIV 7 6 5 4 3 2 1 0 – – – – – – – USBS • USBS: USB OHCI Input Clock Selection 0: USB Clock Input is PLLA 1: USB Clock Input is UPLL • USBDIV: Divider for USB OHCI Clock USB Clock is Input clock divided by USBDIV + 1. SAM9M11 [DATASHEET] 359 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.12 PMC Master Clock Register Name: PMC_MCKR Address: 0xFFFFFC30 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – PLLADIV2 – – MDIV 7 6 5 4 3 2 1 0 – – – PRES CSS • CSS: Master/Processor Clock Source Selection CSS Clock Source Selection 0 0 Slow Clock is selected. 0 1 Main Clock is selected. 1 0 PLLA Output clock is selected. 1 1 UPLL Output clock is selected. • PRES: Master/Processor Clock Prescaler PRES Master/Processor Clock Dividers Input Clock 0 0 0 Selected clock 0 0 1 Selected clock divided by 2 0 1 0 Selected clock divided by 4 0 1 1 Selected clock divided by 8 1 0 0 Selected clock divided by 16 1 0 1 Selected clock divided by 32 1 1 0 Selected clock divided by 64 1 1 1 Reserved 360 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• MDIV: Master Clock Division MDIV Master Clock Division Master Clock is Prescaler Output Clock divided by 1. 0 0 Warning: SysClk DDR and DDRCK are not available. Master Clock is Prescaler Output Clock divided by 2. 0 1 SysClk DDR is equal to 2 x MCK. DDRCK is equal to MCK. Master Clock is Prescaler Output Clock divided by 4. 1 0 SysClk DDR is equal to 2 x MCK. DDRCK is equal to MCK. Master Clock is Prescaler Output Clock divided by 3. 1 1 SysClk DDR is equal to 2 x MCK. DDRCK is equal to MCK. Note: It is forbidden to modify MDIV and CSS at the same access. Each field must be modified separately with a wait for MCKRDY flag between the first field modification and the second field modification. • PLLADIV2: PLLA divisor by 2 PLLADIV2 PLLA Clock Division 0 PLLA clock frequency is divided by 1. 1 PLLA clock frequency is divided by 2. SAM9M11 [DATASHEET] 361 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.13 PMC Programmable Clock Register Name: PMC_PCKx Address: 0xFFFFFC40 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – SLCKMCK 7 6 5 4 3 2 1 0 – – – PRES CSS • CSS: Master Clock Selection CSS Clock Source Selection 0 0 Slow Clock or Master Clock may be selected depending on SLCKMCK field. 0 1 Main Clock is selected. 1 0 PLLACK/PLLADIV2 is selected. 1 1 UPLLCK is selected. • PRES: Programmable Clock Prescaler PRES Programmable Clock 0 0 0 Selected clock 0 0 1 Selected clock divided by 2 0 1 0 Selected clock divided by 4 0 1 1 Selected clock divided by 8 1 0 0 Selected clock divided by 16 1 0 1 Selected clock divided by 32 1 1 0 Selected clock divided by 64 1 1 1 Reserved • SLCKMCK: Slow Clock or Master Clock Selection 0: Slow clock is selected 1: Master clock is selected To select between Slow Clock and Master Clock, the CSS field must be programmed to ‘00’. 362 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.14 PMC Interrupt Enable Register Name: PMC_IER Address: 0xFFFFFC60 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – PCK5 PCK4 PCKRDY1 PCKRDY0 7 6 5 4 3 2 1 0 – LOCKU – – MCKRDY – LOCKA MOSCS • MOSCS: Main Oscillator Status Interrupt Enable • LOCKA: PLL Lock Interrupt Enable • MCKRDY: Master Clock Ready Interrupt Enable • LOCKU: UTMI PLL Lock Interrupt Enable • PCKRDYx: Programmable Clock Ready x Interrupt Enable 0: No effect. 1: Enables the corresponding interrupt. SAM9M11 [DATASHEET] 363 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.15 PMC Interrupt Disable Register Name: PMC_IDR Address: 0xFFFFFC64 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – PCK5 PCK4 PCKRDY1 PCKRDY0 7 6 5 4 3 2 1 0 – LOCKU – – MCKRDY – LOCKA MOSCS • MOSCS: Main Oscillator Status Interrupt Disable • LOCKA: PLLA Lock Interrupt Disable • MCKRDY: Master Clock Ready Interrupt Disable • LOCKU: UTMI PLL Lock Interrupt Disable • PCKRDYx: Programmable Clock Ready x Interrupt Disable 0: No effect. 1: Disables the corresponding interrupt. 364 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.16 PMC Status Register Name: PMC_SR Address: 0xFFFFFC68 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – PCK5 PCK4 PCKRDY1 PCKRDY0 7 6 5 4 3 2 1 0 – LOCKU – – MCKRDY – LOCKA MOSCS • MOSCS: MOSCS Flag Status 0: Main oscillator is not stabilized. 1: Main oscillator is stabilized. • LOCKA: PLLA Lock Status 0: PLLA is not locked 1: PLLA is locked. • MCKRDY: Master Clock Status 0: Master Clock is not ready. 1: Master Clock is ready. • LOCKU: UPLL Lock Status 0: UPLL is not locked 1: UPLL is locked. • PCKRDYx: Programmable Clock Ready Status 0: Programmable Clock x is not ready. 1: Programmable Clock x is ready. SAM9M11 [DATASHEET] 365 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.17 PMC Interrupt Mask Register Name: PMC_IMR Address: 0xFFFFFC6C Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – PCK5 PCK4 PCKRDY1 PCKRDY0 7 6 5 4 3 2 1 0 – LOCKU – – MCKRDY – LOCKA MOSCS • MOSCS: Main Oscillator Status Interrupt Mask • LOCKA: PLLA Lock Interrupt Mask • MCKRDY: Master Clock Ready Interrupt Mask • LOCKU: UTMI PLL Lock Interrupt Mask • PCKRDYx: Programmable Clock Ready x Interrupt Mask 0: The corresponding interrupt is enabled. 1: The corresponding interrupt is disabled. 366 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

25.12.18 PLL Charge Pump Current Register Name: PMC_PLLICPR Address: 0xFFFFFC80 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – ICPLLA • ICPLLA: Charge Pump Current To optimize clock performance, this field must be programmed as specified in “PLL A Characteristics” in the Electrical Characteristics section of the product datasheet. SAM9M11 [DATASHEET] 367 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26. Serial Peripheral Interface (SPI) 26.1 Description The Serial Peripheral Interface (SPI) circuit is a synchronous serial data link that provides communication with external devices in Master or Slave Mode. It also enables communication between processors if an external processor is connected to the system. The Serial Peripheral Interface is essentially a shift register that serially transmits data bits to other SPIs. During a data transfer, one SPI system acts as the “master”' which controls the data flow, while the other devices act as “slaves'' which have data shifted into and out by the master. Different CPUs can take turn being masters (Multiple Master Protocol opposite to Single Master Protocol where one CPU is always the master while all of the others are always slaves) and one master may simultaneously shift data into multiple slaves. However, only one slave may drive its output to write data back to the master at any given time. A slave device is selected when the master asserts its NSS signal. If multiple slave devices exist, the master generates a separate slave select signal for each slave (NPCS). The SPI system consists of two data lines and two control lines:  Master Out Slave In (MOSI): This data line supplies the output data from the master shifted into the input(s) of the slave(s).  Master In Slave Out (MISO): This data line supplies the output data from a slave to the input of the master. There may be no more than one slave transmitting data during any particular transfer.  Serial Clock (SPCK): This control line is driven by the master and regulates the flow of the data bits. The master may transmit data at a variety of baud rates; the SPCK line cycles once for each bit that is transmitted.  Slave Select (NSS): This control line allows slaves to be turned on and off by hardware. 26.2 Embedded Characteristics  Supports communication with serial external devices ̶ Four chip selects with external decoder support allow communication with up to 15 peripherals ̶ Serial memories, such as DataFlash and 3-wire EEPROMs ̶ Serial peripherals, such as ADCs, DACs, LCD Controllers, CAN Controllers and Sensors ̶ External co-processors  Master or slave serial peripheral bus interface ̶ 8- to 16-bit programmable data length per chip select ̶ Programmable phase and polarity per chip select ̶ Programmable transfer delays between consecutive transfers and between clock and data per chip select ̶ Programmable delay between consecutive transfers ̶ Selectable mode fault detection  Very fast transfers supported ̶ Transfers with baud rates up to MCK ̶ The chip select line may be left active to speed up transfers on the same device 368 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.3 Block Diagram Figure 26-1. Block Diagram PDC APB SPCK MISO MOSI MCK PMC SPI Interface PIO NPCS0/NSS NPCS1 NPCS2 Interrupt Control NPCS3 SPI Interrupt Figure 26-2. Block Diagram AHB Matrix DMA Ch. Peripheral Bridge APB SPCK MISO MOSI MCK PMC SPI Interface PIO NPCS0/NSS NPCS1 NPCS2 Interrupt Control NPCS3 SPI Interrupt SAM9M11 [DATASHEET] 369 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.4 Application Block Diagram Figure 26-3. Application Block Diagram: Single Master/Multiple Slave Implementation SPCK SPCK MISO MISO Slave 0 MOSI MOSI SPI Master NPCS0 NSS SPCK NPCS1 MISO NPCS2 NC Slave 1 NPCS3 MOSI NSS SPCK MISO Slave 2 MOSI NSS 26.5 Signal Description Table 26-1. Signal Description Type Pin Name Pin Description Master Slave MISO Master In Slave Out Input Output MOSI Master Out Slave In Output Input SPCK Serial Clock Output Input NPCS1–NPCS3 Peripheral Chip Selects Output Unused NPCS0/NSS Peripheral Chip Select/Slave Select Output Input 370 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.6 Product Dependencies 26.6.1 I/O Lines The pins used for interfacing the compliant external devices may be multiplexed with PIO lines. The programmer must first program the PIO controllers to assign the SPI pins to their peripheral functions. Table 26-2. I/O Lines Instance Signal I/O Line Peripheral SPI0 SPI0_MISO PB0 A SPI0 SPI0_MOSI PB1 A SPI0 SPI0_NPCS0 PB3 A SPI0 SPI0_NPCS1 PB18 B SPI0 SPI0_NPCS1 PD24 A SPI0 SPI0_NPCS2 PB19 B SPI0 SPI0_NPCS2 PD25 A SPI0 SPI0_NPCS3 PD27 B SPI0 SPI0_SPCK PB2 A SPI1 SPI1_MISO PB14 A SPI1 SPI1_MOSI PB15 A SPI1 SPI1_NPCS0 PB17 A SPI1 SPI1_NPCS1 PD28 B SPI1 SPI1_NPCS2 PD18 A SPI1 SPI1_NPCS3 PD19 A SPI1 SPI1_SPCK PB16 A 26.6.2 Power Management The SPI may be clocked through the Power Management Controller (PMC), thus the programmer must first configure the PMC to enable the SPI clock. 26.6.3 Interrupt The SPI interface has an interrupt line connected to the Advanced Interrupt Controller (AIC). Handling the SPI interrupt requires programming the AIC before configuring the SPI. Table 26-3. Peripheral IDs Instance ID SPI0 14 SPI1 15 26.6.4 Peripheral DMA Controller (PDC) or Direct Memory Access Controller (DMAC) The SPI interface can be used in conjunction with the PDC or DMAC in order to reduce processor overhead. For a full description of the PDC or DMAC, refer to the corresponding section in the full datasheet. SAM9M11 [DATASHEET] 371 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.7 Functional Description 26.7.1 Modes of Operation The SPI operates in Master Mode or in Slave Mode. Operation in Master Mode is programmed by writing at 1 the MSTR bit in the Mode Register. The pins NPCS0 to NPCS3 are all configured as outputs, the SPCK pin is driven, the MISO line is wired on the receiver input and the MOSI line driven as an output by the transmitter. If the MSTR bit is written at 0, the SPI operates in Slave Mode. The MISO line is driven by the transmitter output, the MOSI line is wired on the receiver input, the SPCK pin is driven by the transmitter to synchronize the receiver. The NPCS0 pin becomes an input, and is used as a Slave Select signal (NSS). The pins NPCS1 to NPCS3 are not driven and can be used for other purposes. The data transfers are identically programmable for both modes of operations. The baud rate generator is activated only in Master Mode. 26.7.2 Data Transfer Four combinations of polarity and phase are available for data transfers. The clock polarity is programmed with the CPOL bit in the Chip Select Register. The clock phase is programmed with the NCPHA bit. These two parameters determine the edges of the clock signal on which data is driven and sampled. Each of the two parameters has two possible states, resulting in four possible combinations that are incompatible with one another. Thus, a master/slave pair must use the same parameter pair values to communicate. If multiple slaves are used and fixed in different configurations, the master must reconfigure itself each time it needs to communicate with a different slave. Table 26-4 shows the four modes and corresponding parameter settings. Table 26-4. SPI Bus Protocol Mode SPI Mode CPOL NCPHA Shift SPCK Edge Capture SPCK Edge SPCK Inactive Level 0 0 1 Falling Rising Low 1 0 0 Rising Falling Low 2 1 1 Rising Falling High 3 1 0 Falling Rising High Figure 26-4 and Figure 26-5 show examples of data transfers. 372 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 26-4. SPI Transfer Format (NCPHA = 1, 8 bits per transfer) SPCK cycle (for reference) 1 2 3 4 5 66 7 8 SPCK (CPOL = 0) SPCK (CPOL = 1) MOSI MSB 6 5 4 3 2 1 LSB (from master) MISO MSB 6 5 4 3 2 1 LSB * (from slave) NSS (to slave) * Not defined, but normally MSB of previous character received. Figure 26-5. SPI Transfer Format (NCPHA = 0, 8 bits per transfer) SPCK cycle (for reference) 1 2 3 4 5 6 7 8 SPCK (CPOL = 0) SPCK (CPOL = 1) MOSI MSB 6 5 4 3 2 1 LSB (from master) MISO (from slave) * MSB 6 5 4 3 2 1 LSB NSS (to slave) * Not defined but normally LSB of previous character transmitted. SAM9M11 [DATASHEET] 373 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.7.3 Master Mode Operations When configured in Master Mode, the SPI operates on the clock generated by the internal programmable baud rate generator. It fully controls the data transfers to and from the slave(s) connected to the SPI bus. The SPI drives the chip select line to the slave and the serial clock signal (SPCK). The SPI features two holding registers, the Transmit Data Register and the Receive Data Register, and a single Shift Register. The holding registers maintain the data flow at a constant rate. After enabling the SPI, a data transfer begins when the processor writes to the SPI_TDR (Transmit Data Register). The written data is immediately transferred in the Shift Register and transfer on the SPI bus starts. While the data in the Shift Register is shifted on the MOSI line, the MISO line is sampled and shifted in the Shift Register. Receiving data cannot occur without transmitting data. If receiving mode is not needed, for example when communicating with a slave receiver only (such as an LCD), the receive status flags in the status register can be discarded. Before writing the TDR, the PCS field in the SPI_MR must be set in order to select a slave. After enabling the SPI, a data transfer begins when the processor writes to the SPI_TDR (Transmit Data Register). The written data is immediately transferred in the Shift Register and transfer on the SPI bus starts. While the data in the Shift Register is shifted on the MOSI line, the MISO line is sampled and shifted in the Shift Register. Transmission cannot occur without reception. Before writing the TDR, the PCS field must be set in order to select a slave. If new data is written in SPI_TDR during the transfer, it stays in it until the current transfer is completed. Then, the received data is transferred from the Shift Register to SPI_RDR, the data in SPI_TDR is loaded in the Shift Register and a new transfer starts. The transfer of a data written in SPI_TDR in the Shift Register is indicated by the TDRE bit (Transmit Data Register Empty) in the Status Register (SPI_SR). When new data is written in SPI_TDR, this bit is cleared. The TDRE bit is used to trigger the Transmit PDC channel. The end of transfer is indicated by the TXEMPTY flag in the SPI_SR. If a transfer delay (DLYBCT) is greater than 0 for the last transfer, TXEMPTY is set after the completion of said delay. The master clock (MCK) can be switched off at this time. The transfer of received data from the Shift Register in SPI_RDR is indicated by the RDRF bit (Receive Data Register Full) in the Status Register (SPI_SR). When the received data is read, the RDRF bit is cleared. If the SPI_RDR (Receive Data Register) has not been read before new data is received, the Overrun Error bit (OVRES) in SPI_SR is set. As long as this flag is set, data is loaded in SPI_RDR. The user has to read the status register to clear the OVRES bit. Figure 26-6 on page 375 shows a block diagram of the SPI when operating in Master Mode. Figure 26-7 on page 376 shows a flow chart describing how transfers are handled. 374 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.7.3.1 Master Mode Block Diagram Figure 26-6. Master Mode Block Diagram SPI_CSR0..3 SCBR MCK Baud Rate Generator SPCK SPI Clock SPI_CSR0..3 SPI_RDR RDRF BITS RD OVRES NCPHA CPOL LSB MSB MISO Shift Register MOSI SPI_TDR TD TDRE SPI_CSR0..3 SPI_RDR CSAAT PCS PS NPCS3 PCSDEC SPI_MR PCS Current NPCS2 0 Peripheral NPCS1 SPI_TDR PCS NPCS0 1 MSTR MODF NPCS0 MODFDIS SAM9M11 [DATASHEET] 375 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.7.3.2 Master Mode Flow Diagram Figure 26-7. Master Mode Flow Diagram SPI Enable - NPCS defines the current Chip Select - CSAAT, DLYBS, DLYBCT refer to the fields of the Chip Select Register corresponding to the Current Chip Select - When NPCS is 0xF, CSAAT is 0. 1 TDRE ? 0 Fixed 1 0 peripheral CSAAT ? PS ? Variable 0 1 peripheral Fixed 0 peripheral yes SPI_TDR(PCS) SPI_MR(PCS) PS ? = NPCS ? = NPCS ? Variable 1 peripheral no no NPCS = SPI_TDR(PCS) NPCS = SPI_MR(PCS) NPCS = 0xF NPCS = 0xF Delay DLYBCS Delay DLYBCS NPCS = SPI_TDR(PCS) NPCS = SPI_MR(PCS), SPI_TDR(PCS) Delay DLYBS Serializer = SPI_TDR(TD) TDRE = 1 Data Transfer SPI_RDR(RD) = Serializer RDRF = 1 Delay DLYBCT 0 TDRE ? 1 1 CSAAT ? 0 NPCS = 0xF Delay DLYBCS 376 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 26-8 shows Transmit Data Register Empty (TDRE), Receive Data Register (RDRF) and Transmission Register Empty (TXEMPTY) status flags behavior within the SPI_SR (Status Register) during an 8-bit data transfer in fixed mode and no Peripheral Data Controller involved. Figure 26-8. Status Register Flags Behavior 1 2 3 4 5 66 7 8 SPCK NPCS0 MOSI MSB 6 5 4 3 2 1 LSB (from master) TDRE RDR read Write in SPI_TDR RDRF MISO MSB 6 5 4 3 2 1 LSB (from slave) TXEMPTY shift register empty SAM9M11 [DATASHEET] 377 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 26-9 shows Transmission Register Empty (TXEMPTY), End of RX buffer (ENDRX), End of TX buffer (ENDTX), RX Buffer Full (RXBUFF) and TX Buffer Empty (TXBUFE) status flags behavior within the SPI_SR (Status Register) during an 8-bit data transfer in fixed mode with the Peripheral Data Controller involved. The PDC is programmed to transfer and receive three data. The next pointer and counter are not used. The RDRF and TDRE are not shown because these flags are managed by the PDC when using the PDC. Figure 26-9. PDC Status Register Flags Behavior 1 2 3 SPCK NPCS0 MOSI MSB 6 5 4 3 2 1 LSB MSB 6 5 4 3 2 1 LSB MSB 6 5 4 3 2 1 LSB (from master) MISO MSB 6 5 4 3 2 1 LSB MSB 6 5 4 3 2 1 LSB MSB 6 5 4 3 2 1 LSB (from slave) ENDTX ENDRX TXBUFE RXBUFF TXEMPTY 26.7.3.3 Clock Generation The SPI Baud rate clock is generated by dividing the Master Clock (MCK), by a value between 1 and 255. This allows a maximum operating baud rate at up to Master Clock and a minimum operating baud rate of MCK divided by 255. Programming the SCBR field at 0 is forbidden. Triggering a transfer while SCBR is at 0 can lead to unpredictable results. At reset, SCBR is 0 and the user has to program it at a valid value before performing the first transfer. The divisor can be defined independently for each chip select, as it has to be programmed in the SCBR field of the Chip Select Registers. This allows the SPI to automatically adapt the baud rate for each interfaced peripheral without reprogramming. 378 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.7.3.4 Transfer Delays Figure 26-10 shows a chip select transfer change and consecutive transfers on the same chip select. Three delays can be programmed to modify the transfer waveforms:  The delay between chip selects, programmable only once for all the chip selects by writing the DLYBCS field in the Mode Register. Allows insertion of a delay between release of one chip select and before assertion of a new one.  The delay before SPCK, independently programmable for each chip select by writing the field DLYBS. Allows the start of SPCK to be delayed after the chip select has been asserted.  The delay between consecutive transfers, independently programmable for each chip select by writing the DLYBCT field. Allows insertion of a delay between two transfers occurring on the same chip select These delays allow the SPI to be adapted to the interfaced peripherals and their speed and bus release time. Figure 26-10. Programmable Delays Chip Select 1 Chip Select 2 SPCK DLYBCS DLYBS DLYBCT DLYBCT 26.7.3.5 Peripheral Selection The serial peripherals are selected through the assertion of the NPCS0 to NPCS3 signals. By default, all the NPCS signals are high before and after each transfer.  Fixed Peripheral Select: SPI exchanges data with only one peripheral Fixed Peripheral Select is activated by writing the PS bit to zero in SPI_MR (Mode Register). In this case, the current peripheral is defined by the PCS field in SPI_MR and the PCS field in the SPI_TDR has no effect.  Variable Peripheral Select: Data can be exchanged with more than one peripheral without having to reprogram the NPCS field in the SPI_MR register. Variable Peripheral Select is activated by setting PS bit to one. The PCS field in SPI_TDR is used to select the current peripheral. This means that the peripheral selection can be defined for each new data. The value to write in the SPI_TDR register as the following format. [xxxxxxx(7-bit) + LASTXFER(1-bit)(1)+ xxxx(4-bit) + PCS (4-bit) + DATA (8 to 16-bit)] with PCS equals to the chip select to assert as defined in Section 26.8.4 (SPI Transmit Data Register) and LASTXFER bit at 0 or 1 depending on CSAAT bit. CSAAT, LASTXFER and CSNAAT bit are discussed in the Peripheral Deselection in Section 26.7.3.11. Note: 1. Optional. 26.7.3.6 SPI Peripheral DMA Controller (PDC) In both fixed and variable mode the Peripheral DMA Controller (PDC) can be used to reduce processor overhead. The Fixed Peripheral Selection allows buffer transfers with a single peripheral. Using the PDC is an optimal means, as the size of the data transfer between the memory and the SPI is either 8 bits or 16 bits. However, changing the peripheral selection requires the Mode Register to be reprogrammed. SAM9M11 [DATASHEET] 379 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The Variable Peripheral Selection allows buffer transfers with multiple peripherals without reprogramming the Mode Register. Data written in SPI_TDR is 32 bits wide and defines the real data to be transmitted and the peripheral it is destined to. Using the PDC in this mode requires 32-bit wide buffers, with the data in the LSBs and the PCS and LASTXFER fields in the MSBs, however the SPI still controls the number of bits (8 to16) to be transferred through MISO and MOSI lines with the chip select configuration registers. This is not the optimal means in term of memory size for the buffers, but it provides a very effective means to exchange data with several peripherals without any intervention of the processor. 26.7.3.7 Transfer Size Depending on the data size to transmit, from 8 to 16 bits, the PDC manages automatically the type of pointer's size it has to point to. The PDC will perform the following transfer size depending on the mode and number of bits per data. Fixed Mode:  8-bit Data: Byte transfer, PDC Pointer Address = Address + 1 byte, PDC Counter = Counter - 1  8-bit to 16-bit Data: 2 bytes transfer. n-bit data transfer with don’t care data (MSB) filled with 0’s, PDC Pointer Address = Address + 2 bytes, PDC Counter = Counter - 1 Variable Mode: In variable Mode, PDC Pointer Address = Address +4 bytes and PDC Counter = Counter - 1 for 8 to 16-bit transfer size. When using the PDC, the TDRE and RDRF flags are handled by the PDC, thus the user’s application does not have to check those bits. Only End of RX Buffer (ENDRX), End of TX Buffer (ENDTX), Buffer Full (RXBUFF), TX Buffer Empty (TXBUFE) are significant. For further details about the Peripheral DMA Controller and user interface, refer to the PDC section of the product datasheet. 26.7.3.8 SPI Direct Access Memory Controller (DMAC) In both fixed and variable mode the Direct Memory Access Controller (DMAC) can be used to reduce processor overhead. The Fixed Peripheral Selection allows buffer transfers with a single peripheral. Using the DMAC is an optimal means, as the size of the data transfer between the memory and the SPI is either 8 bits or 16 bits. However, changing the peripheral selection requires the Mode Register to be reprogrammed. The Variable Peripheral Selection allows buffer transfers with multiple peripherals without reprogramming the Mode Register. Data written in SPI_TDR is 32 bits wide and defines the real data to be transmitted and the peripheral it is destined to. Using the DMAC in this mode requires 32-bit wide buffers, with the data in the LSBs and the PCS and LASTXFER fields in the MSBs, however the SPI still controls the number of bits (8 to16) to be transferred through MISO and MOSI lines with the chip select configuration registers. This is not the optimal means in term of memory size for the buffers, but it provides a very effective means to exchange data with several peripherals without any intervention of the processor. 26.7.3.9 Peripheral Chip Select Decoding The user can program the SPI to operate with up to 15 peripherals by decoding the four Chip Select lines, NPCS0 to NPCS3 with 1 of up to 16 decoder/demultiplexer. This can be enabled by writing the PCSDEC bit at 1 in the Mode Register (SPI_MR). When operating without decoding, the SPI makes sure that in any case only one chip select line is activated, i.e., one NPCS line driven low at a time. If two bits are defined low in a PCS field, only the lowest numbered chip select is driven low. 380 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

When operating with decoding, the SPI directly outputs the value defined by the PCS field on NPCS lines of either the Mode Register or the Transmit Data Register (depending on PS). As the SPI sets a default value of 0xF on the chip select lines (i.e., all chip select lines at 1) when not processing any transfer, only 15 peripherals can be decoded. The SPI has only four Chip Select Registers, not 15. As a result, when decoding is activated, each chip select defines the characteristics of up to four peripherals. As an example, SPI_CRS0 defines the characteristics of the externally decoded peripherals 0 to 3, corresponding to the PCS values 0x0 to 0x3. Thus, the user has to make sure to connect compatible peripherals on the decoded chip select lines 0 to 3, 4 to 7, 8 to 11 and 12 to 14. Figure 26-11 below shows such an implementation. If the CSAAT bit is used, with or without the PDC, the Mode Fault detection for NPCS0 line must be disabled. This is not needed for all other chip select lines since Mode Fault Detection is only on NPCS0. If the CSAAT bit is used, with or without the DMAC, the Mode Fault detection for NPCS0 line must be disabled. This is not needed for all other chip select lines since Mode Fault Detection is only on NPCS0. Figure 26-11. Chip Select Decoding Application Block Diagram: Single Master/Multiple Slave Implementation SPCK MISO MOSI SPCK MISO MOSI SPCK MISO MOSI SPCK MISO MOSI Slave 0 Slave 1 Slave 14 SPI Master NSS NSS NSS NPCS0 NPCS1 NPCS2 NPCS3 1-of-n Decoder/Demultiplexer SAM9M11 [DATASHEET] 381 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.7.3.10 Peripheral Deselection Without PDC nor DMAC During a transfer of more than one data on a Chip Select without the PDC nor DMAC, the SPI_TDR is loaded by the processor, the flag TDRE rises as soon as the content of the SPI_TDR is transferred into the internal shift register. When this flag is detected high, the SPI_TDR can be reloaded. If this reload by the processor occurs before the end of the current transfer and if the next transfer is performed on the same chip select as the current transfer, the Chip Select is not de-asserted between the two transfers. But depending on the application software handling the SPI status register flags (by interrupt or polling method) or servicing other interrupts or other tasks, the processor may not reload the SPI_TDR in time to keep the chip select active (low). A null Delay Between Consecutive Transfer (DLYBCT) value in the SPI_CSR, will give even less time for the processor to reload the SPI_TDR. With some SPI slave peripherals, requiring the chip select line to remain active (low) during a full set of transfers might lead to communication errors. To facilitate interfacing with such devices, the Chip Select Register [CSR0...CSR3] can be programmed with the CSAAT bit (Chip Select Active After Transfer) at 1. This allows the chip select lines to remain in their current state (low = active) until transfer to another chip select is required. Even if the SPI_TDR is not reloaded the chip select will remain active. To have the chip select line to raise at the end of the transfer the Last Transfer Bit (LASTXFER) in the SPI_MR must be set at 1 before writing the last data to transmit into the SPI_TDR. 26.7.3.11 Peripheral Deselection with PDC When the Peripheral DMA Controller is used, the chip select line will remain low during the whole transfer since the TDRE flag is managed by the PDC itself. The reloading of the SPI_TDR by the PDC is done as soon as TDRE flag is set to one. In this case the use of CSAAT bit might not be needed. However, it may happen that when other PDC channels connected to other peripherals are in use as well, the SPI PDC might be delayed by another (PDC with a higher priority on the bus). Having PDC buffers in slower memories like flash memory or SDRAM compared to fast internal SRAM, may lengthen the reload time of the SPI_TDR by the PDC as well. This means that the SPI_TDR might not be reloaded in time to keep the chip select line low. In this case the chip select line may toggle between data transfer and according to some SPI Slave devices, the communication might get lost. The use of the CSAAT bit might be needed. 26.7.3.12 Peripheral Deselection with DMAC When the Direct Memory Access Controller is used, the chip select line will remain low during the whole transfer since the TDRE flag is managed by the DMAC itself. The reloading of the SPI_TDR by the DMAC is done as soon as TDRE flag is set to one. In this case the use of CSAAT bit might not be needed. However, it may happen that when other DMAC channels connected to other peripherals are in use as well, the SPI DMAC might be delayed by another (DMAC with a higher priority on the bus). Having DMAC buffers in slower memories like flash memory or SDRAM compared to fast internal SRAM, may lengthen the reload time of the SPI_TDR by the DMAC as well. This means that the SPI_TDR might not be reloaded in time to keep the chip select line low. In this case the chip select line may toggle between data transfer and according to some SPI Slave devices, the communication might get lost. The use of the CSAAT bit might be needed. Figure 26-12 shows different peripheral deselction cases and the effect of the CSAAT bit. 382 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 26-12. Peripheral Deselection CSAAT = 0 CSAAT = 1 TDRE DLYBCT DLYBCT NPCS[0..3] A A A A A DLYBCS DLYBCS PCS = A PCS = A Write SPI_TDR TDRE DLYBCT DLYBCT NPCS[0..3] A A A A A DLYBCS DLYBCS PCS=A PCS = A Write SPI_TDR TDRE DLYBCT DLYBCT NPCS[0..3] A B A B DLYBCS DLYBCS PCS = B PCS = B Write SPI_TDR 26.7.3.13 Mode Fault Detection A mode fault is detected when the SPI is programmed in Master Mode and a low level is driven by an external master on the NPCS0/NSS signal. In this case, multi-master configuration, NPCS0, MOSI, MISO and SPCK pins must be configured in open drain (through the PIO controller). When a mode fault is detected, the MODF bit in the SPI_SR is set until the SPI_SR is read and the SPI is automatically disabled until re-enabled by writing the SPIEN bit in the SPI_CR (Control Register) at 1. By default, the Mode Fault detection circuitry is enabled. The user can disable Mode Fault detection by setting the MODFDIS bit in the SPI Mode Register (SPI_MR). 26.7.4 SPI Slave Mode When operating in Slave Mode, the SPI processes data bits on the clock provided on the SPI clock pin (SPCK). The SPI waits for NSS to go active before receiving the serial clock from an external master. When NSS falls, the clock is validated on the serializer, which processes the number of bits defined by the BITS field of the Chip Select Register 0 (SPI_CSR0). These bits are processed following a phase and a polarity defined respectively by the NCPHA and CPOL bits of the SPI_CSR0. Note that BITS, CPOL and NCPHA of the other Chip Select Registers have no effect when the SPI is programmed in Slave Mode. The bits are shifted out on the MISO line and sampled on the MOSI line. (For more information on the BITS field, see the note below the register bitmap in Section 26.8.9 “SPI Chip Select Register” on page 396.) SAM9M11 [DATASHEET] 383 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

When all the bits are processed, the received data is transferred in the Receive Data Register and the RDRF bit rises. If the SPI_RDR (Receive Data Register) has not been read before new data is received, the Overrun Error bit (OVRES) in SPI_SR is set. As long as this flag is set, data is loaded in SPI_RDR. The user has to read the status register to clear the OVRES bit. When a transfer starts, the data shifted out is the data present in the Shift Register. If no data has been written in the Transmit Data Register (SPI_TDR), the last data received is transferred. If no data has been received since the last reset, all bits are transmitted low, as the Shift Register resets at 0. When a first data is written in SPI_TDR, it is transferred immediately in the Shift Register and the TDRE bit rises. If new data is written, it remains in SPI_TDR until a transfer occurs, i.e., NSS falls and there is a valid clock on the SPCK pin. When the transfer occurs, the last data written in SPI_TDR is transferred in the Shift Register and the TDRE bit rises. This enables frequent updates of critical variables with single transfers. Then, a new data is loaded in the Shift Register from the Transmit Data Register. In case no character is ready to be transmitted, i.e., no character has been written in SPI_TDR since the last load from SPI_TDR to the Shift Register, the Shift Register is not modified and the last received character is retransmitted. Figure 26-13 shows a block diagram of the SPI when operating in Slave Mode. Figure 26-13. Slave Mode Functional Block Diagram SPCK NSS SPI Clock SPIEN SPIENS SPIDIS SPI_CSR0 SPI_RDR RDRF BITS NCPHA RD OVRES CPOL LSB MSB MOSI Shift Register MISO SPI_TDR TD TDRE 384 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.8 Serial Peripheral Interface (SPI) User Interface Table 26-5. Register Mapping Offset Register Name Access Reset 0x00 Control Register SPI_CR Write-only – 0x04 Mode Register SPI_MR Read/Write 0x0 0x08 Receive Data Register SPI_RDR Read-only 0x0 0x0C Transmit Data Register SPI_TDR Write-only – 0x10 Status Register SPI_SR Read-only 0x000000F0 0x14 Interrupt Enable Register SPI_IER Write-only – 0x18 Interrupt Disable Register SPI_IDR Write-only – 0x1C Interrupt Mask Register SPI_IMR Read-only 0x0 0x20–0x2C Reserved – – – 0x30 Chip Select Register 0 SPI_CSR0 Read/Write 0x0 0x34 Chip Select Register 1 SPI_CSR1 Read/Write 0x0 0x38 Chip Select Register 2 SPI_CSR2 Read/Write 0x0 0x3C Chip Select Register 3 SPI_CSR3 Read/Write 0x0 0x004C–0x00FC Reserved – – – 0x100–0x124 Reserved for the PDC – – – SAM9M11 [DATASHEET] 385 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.8.1 SPI Control Register Name: SPI_CR Address: 0xFFFA4000 (0), 0xFFFA8000 (1) Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – LASTXFER 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 SWRST – – – – – SPIDIS SPIEN • SPIEN: SPI Enable 0: No effect. 1: Enables the SPI to transfer and receive data. • SPIDIS: SPI Disable 0: No effect. 1: Disables the SPI. As soon as SPIDIS is set, SPI finishes its transfer. All pins are set in input mode and no data is received or transmitted. If a transfer is in progress, the transfer is finished before the SPI is disabled. If both SPIEN and SPIDIS are equal to one when the control register is written, the SPI is disabled. • SWRST: SPI Software Reset 0: No effect. 1: Reset the SPI. A software-triggered hardware reset of the SPI interface is performed. The SPI is in slave mode after software reset. PDC channels are not affected by software reset. • LASTXFER: Last Transfer 0: No effect. 1: The current NPCS will be deasserted after the character written in TD has been transferred. When CSAAT is set, this allows to close the communication with the current serial peripheral by raising the corresponding NPCS line as soon as TD transfer has completed. 386 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.8.2 SPI Mode Register Name: SPI_MR Address: 0xFFFA4004 (0), 0xFFFA8004 (1) Access: Read/Write 31 30 29 28 27 26 25 24 DLYBCS 23 22 21 20 19 18 17 16 – – – – PCS 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 LLB – WDRBT MODFDIS – PCSDEC PS MSTR • MSTR: Master/Slave Mode 0: SPI is in Slave mode. 1: SPI is in Master mode. • PS: Peripheral Select 0: Fixed Peripheral Select. 1: Variable Peripheral Select. • PCSDEC: Chip Select Decode 0: The chip selects are directly connected to a peripheral device. 1: The four chip select lines are connected to a 4- to 16-bit decoder. When PCSDEC equals one, up to 15 Chip Select signals can be generated with the four lines using an external 4- to 16-bit decoder. The Chip Select Registers define the characteristics of the 15 chip selects according to the following rules: SPI_CSR0 defines peripheral chip select signals 0 to 3. SPI_CSR1 defines peripheral chip select signals 4 to 7. SPI_CSR2 defines peripheral chip select signals 8 to 11. SPI_CSR3 defines peripheral chip select signals 12 to 14. • MODFDIS: Mode Fault Detection 0: Mode fault detection is enabled. 1: Mode fault detection is disabled. • WDRBT: Wait Data Read Before Transfer 0: No effect. In master mode, a transfer can be initiated whatever the state of the Receive Data Register is. 1: In Master Mode, a transfer can start only if the Receive Data Register is empty, i.e., does not contain any unread data. This mode prevents overrun error in reception. SAM9M11 [DATASHEET] 387 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• LLB: Local Loopback Enable 0: Local loopback path disabled. 1: Local loopback path enabled LLB controls the local loopback on the data serializer for testing in Master Mode only. (MISO is internally connected on MOSI.) • PCS: Peripheral Chip Select This field is only used if Fixed Peripheral Select is active (PS = 0). If PCSDEC = 0: PCS = xxx0 NPCS[3:0] = 1110 PCS = xx01 NPCS[3:0] = 1101 PCS = x011 NPCS[3:0] = 1011 PCS = 0111 NPCS[3:0] = 0111 PCS = 1111 forbidden (no peripheral is selected) (x = don’t care) If PCSDEC = 1: NPCS[3:0] output signals = PCS. • DLYBCS: Delay Between Chip Selects This field defines the delay from NPCS inactive to the activation of another NPCS. The DLYBCS time guarantees non- overlapping chip selects and solves bus contentions in case of peripherals having long data float times. If DLYBCS is less than or equal to six, six MCK periods will be inserted by default. Otherwise, the following equation determines the delay: DLYBCS Delay Between Chip Selects = ----------------------- MCK 388 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.8.3 SPI Receive Data Register Name: SPI_RDR Address: 0xFFFA4008 (0), 0xFFFA8008 (1) Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – PCS 15 14 13 12 11 10 9 8 RD 7 6 5 4 3 2 1 0 RD • RD: Receive Data Data received by the SPI Interface is stored in this register right-justified. Unused bits read zero. • PCS: Peripheral Chip Select In Master Mode only, these bits indicate the value on the NPCS pins at the end of a transfer. Otherwise, these bits read zero. SAM9M11 [DATASHEET] 389 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.8.4 SPI Transmit Data Register Name: SPI_TDR Address: 0xFFFA400C (0), 0xFFFA800C (1) Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – LASTXFER 23 22 21 20 19 18 17 16 – – – – PCS 15 14 13 12 11 10 9 8 TD 7 6 5 4 3 2 1 0 TD • TD: Transmit Data Data to be transmitted by the SPI Interface is stored in this register. Information to be transmitted must be written to the transmit data register in a right-justified format. • PCS: Peripheral Chip Select This field is only used if Variable Peripheral Select is active (PS = 1). If PCSDEC = 0: PCS = xxx0 NPCS[3:0] = 1110 PCS = xx01 NPCS[3:0] = 1101 PCS = x011 NPCS[3:0] = 1011 PCS = 0111 NPCS[3:0] = 0111 PCS = 1111 forbidden (no peripheral is selected) (x = don’t care) If PCSDEC = 1: NPCS[3:0] output signals = PCS • LASTXFER: Last Transfer 0: No effect. 1: The current NPCS will be deasserted after the character written in TD has been transferred. When CSAAT is set, this allows to close the communication with the current serial peripheral by raising the corresponding NPCS line as soon as TD transfer has completed. This field is only used if Variable Peripheral Select is active (PS = 1). 390 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.8.5 SPI Status Register Name: SPI_SR Address: 0xFFFA4010 (0), 0xFFFA8010 (1) Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – SPIENS 15 14 13 12 11 10 9 8 – – – – – – TXEMPTY NSSR 7 6 5 4 3 2 1 0 TXBUFE RXBUFF ENDTX ENDRX OVRES MODF TDRE RDRF • RDRF: Receive Data Register Full 0: No data has been received since the last read of SPI_RDR 1: Data has been received and the received data has been transferred from the serializer to SPI_RDR since the last read of SPI_RDR. • TDRE: Transmit Data Register Empty 0: Data has been written to SPI_TDR and not yet transferred to the serializer. 1: The last data written in the Transmit Data Register has been transferred to the serializer. TDRE equals zero when the SPI is disabled or at reset. The SPI enable command sets this bit to one. • MODF: Mode Fault Error 0: No Mode Fault has been detected since the last read of SPI_SR. 1: A Mode Fault occurred since the last read of the SPI_SR. • OVRES: Overrun Error Status 0: No overrun has been detected since the last read of SPI_SR. 1: An overrun has occurred since the last read of SPI_SR. An overrun occurs when SPI_RDR is loaded at least twice from the serializer since the last read of the SPI_RDR. • ENDRX: End of RX buffer 0: The Receive Counter Register has not reached 0 since the last write in SPI_RCR(1) or SPI_RNCR(1). 1: The Receive Counter Register has reached 0 since the last write in SPI_RCR(1) or SPI_RNCR(1). • ENDTX: End of TX buffer 0: The Transmit Counter Register has not reached 0 since the last write in SPI_TCR(1) or SPI_TNCR(1). 1: The Transmit Counter Register has reached 0 since the last write in SPI_TCR(1) or SPI_TNCR(1). • RXBUFF: RX Buffer Full 0: SPI_RCR(1) or SPI_RNCR(1) has a value other than 0. 1: Both SPI_RCR(1) and SPI_RNCR(1) have a value of 0. SAM9M11 [DATASHEET] 391 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• TXBUFE: TX Buffer Empty 0: SPI_TCR(1) or SPI_TNCR(1) has a value other than 0. 1: Both SPI_TCR(1) and SPI_TNCR(1) have a value of 0. • NSSR: NSS Rising 0: No rising edge detected on NSS pin since last read. 1: A rising edge occurred on NSS pin since last read. • TXEMPTY: Transmission Registers Empty 0: As soon as data is written in SPI_TDR. 1: SPI_TDR and internal shifter are empty. If a transfer delay has been defined, TXEMPTY is set after the completion of such delay. • SPIENS: SPI Enable Status 0: SPI is disabled. 1: SPI is enabled. Note: 1. SPI_RCR, SPI_RNCR, SPI_TCR, SPI_TNCR are physically located in the PDC. 392 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.8.6 SPI Interrupt Enable Register Name: SPI_IER Address: 0xFFFA4014 (0), 0xFFFA8014 (1) Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – TXEMPTY NSSR 7 6 5 4 3 2 1 0 TXBUFE RXBUFF ENDTX ENDRX OVRES MODF TDRE RDRF 0: No effect. 1: Enables the corresponding interrupt. • RDRF: Receive Data Register Full Interrupt Enable • TDRE: SPI Transmit Data Register Empty Interrupt Enable • MODF: Mode Fault Error Interrupt Enable • OVRES: Overrun Error Interrupt Enable • ENDRX: End of Receive Buffer Interrupt Enable • ENDTX: End of Transmit Buffer Interrupt Enable • RXBUFF: Receive Buffer Full Interrupt Enable • TXBUFE: Transmit Buffer Empty Interrupt Enable • NSSR: NSS Rising Interrupt Enable • TXEMPTY: Transmission Registers Empty Enable SAM9M11 [DATASHEET] 393 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.8.7 SPI Interrupt Disable Register Name: SPI_IDR Address: 0xFFFA4018 (0), 0xFFFA8018 (1) Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – TXEMPTY NSSR 7 6 5 4 3 2 1 0 TXBUFE RXBUFF ENDTX ENDRX OVRES MODF TDRE RDRF 0: No effect. 1: Disables the corresponding interrupt. • RDRF: Receive Data Register Full Interrupt Disable • TDRE: SPI Transmit Data Register Empty Interrupt Disable • MODF: Mode Fault Error Interrupt Disable • OVRES: Overrun Error Interrupt Disable • ENDRX: End of Receive Buffer Interrupt Disable • ENDTX: End of Transmit Buffer Interrupt Disable • RXBUFF: Receive Buffer Full Interrupt Disable • TXBUFE: Transmit Buffer Empty Interrupt Disable • NSSR: NSS Rising Interrupt Disable • TXEMPTY: Transmission Registers Empty Disable 394 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.8.8 SPI Interrupt Mask Register Name: SPI_IMR Address: 0xFFFA401C (0), 0xFFFA801C (1) Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – TXEMPTY NSSR 7 6 5 4 3 2 1 0 TXBUFE RXBUFF ENDTX ENDRX OVRES MODF TDRE RDRF 0: The corresponding interrupt is not enabled. 1: The corresponding interrupt is enabled. • RDRF: Receive Data Register Full Interrupt Mask • TDRE: SPI Transmit Data Register Empty Interrupt Mask • MODF: Mode Fault Error Interrupt Mask • OVRES: Overrun Error Interrupt Mask • ENDRX: End of Receive Buffer Interrupt Mask • ENDTX: End of Transmit Buffer Interrupt Mask • RXBUFF: Receive Buffer Full Interrupt Mask • TXBUFE: Transmit Buffer Empty Interrupt Mask • NSSR: NSS Rising Interrupt Mask • TXEMPTY: Transmission Registers Empty Mask SAM9M11 [DATASHEET] 395 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

26.8.9 SPI Chip Select Register Name: SPI_CSR0... SPI_CSR3 Address: 0xFFFA4030 (0), 0xFFFA8030 (1) Access: Read/Write 31 30 29 28 27 26 25 24 DLYBCT 23 22 21 20 19 18 17 16 DLYBS 15 14 13 12 11 10 9 8 SCBR 7 6 5 4 3 2 1 0 BITS CSAAT – NCPHA CPOL Note: SPI_CSRx registers must be written even if the user wants to use the defaults. The BITS field will not be updated with the translated value unless the register is written. • CPOL: Clock Polarity 0: The inactive state value of SPCK is logic level zero. 1: The inactive state value of SPCK is logic level one. CPOL is used to determine the inactive state value of the serial clock (SPCK). It is used with NCPHA to produce the required clock/data relationship between master and slave devices. • NCPHA: Clock Phase 0: Data is changed on the leading edge of SPCK and captured on the following edge of SPCK. 1: Data is captured on the leading edge of SPCK and changed on the following edge of SPCK. NCPHA determines which edge of SPCK causes data to change and which edge causes data to be captured. NCPHA is used with CPOL to produce the required clock/data relationship between master and slave devices. • CSAAT: Chip Select Active After Transfer 0: The Peripheral Chip Select Line rises as soon as the last transfer is achieved. 1: The Peripheral Chip Select does not rise after the last transfer is achieved. It remains active until a new transfer is requested on a different chip select. • BITS: Bits Per Transfer (See the note below the register bitmap.) The BITS field determines the number of data bits transferred. Reserved values should not be used. BITS Bits Per Transfer 0000 8 0001 9 0010 10 0011 11 0100 12 0101 13 0110 14 0111 15 396 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

BITS (Continued) Bits Per Transfer 1000 16 1001 Reserved 1010 Reserved 1011 Reserved 1100 Reserved 1101 Reserved 1110 Reserved 1111 Reserved • SCBR: Serial Clock Baud Rate In Master Mode, the SPI Interface uses a modulus counter to derive the SPCK baud rate from the Master Clock MCK. The Baud rate is selected by writing a value from 1 to 255 in the SCBR field. The following equations determine the SPCK baud rate: MCK SPCK Baudrate = --------------- SCBR Programming the SCBR field at 0 is forbidden. Triggering a transfer while SCBR is at 0 can lead to unpredictable results. At reset, SCBR is 0 and the user has to program it at a valid value before performing the first transfer. • DLYBS: Delay Before SPCK This field defines the delay from NPCS valid to the first valid SPCK transition. When DLYBS equals zero, the NPCS valid to SPCK transition is 1/2 the SPCK clock period. Otherwise, the following equations determine the delay: DLYBS Delay Before SPCK = ------------------- MCK • DLYBCT: Delay Between Consecutive Transfers This field defines the delay between two consecutive transfers with the same peripheral without removing the chip select. The delay is always inserted after each transfer and before removing the chip select if needed. When DLYBCT equals zero, no delay between consecutive transfers is inserted and the clock keeps its duty cycle over the character transfers. Otherwise, the following equation determines the delay: 32×DLYBCT Delay Between Consecutive Transfers = ------------------------------------ MCK SAM9M11 [DATASHEET] 397 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27. Advanced Interrupt Controller (AIC) 27.1 Description The Advanced Interrupt Controller (AIC) is an 8-level priority, individually maskable, vectored interrupt controller, providing handling of up to thirty-two interrupt sources. It is designed to substantially reduce the software and real- time overhead in handling internal and external interrupts. The AIC drives the nFIQ (fast interrupt request) and the nIRQ (standard interrupt request) inputs of an ARM processor. Inputs of the AIC are either internal peripheral interrupts or external interrupts coming from the product's pins. The 8-level Priority Controller allows the user to define the priority for each interrupt source, thus permitting higher priority interrupts to be serviced even if a lower priority interrupt is being treated. Internal interrupt sources can be programmed to be level sensitive or edge triggered. External interrupt sources can be programmed to be positive-edge or negative-edge triggered or high-level or low-level sensitive. The fast forcing feature redirects any internal or external interrupt source to provide a fast interrupt rather than a normal interrupt. 27.2 Embedded Characteristics  Controls the interrupt lines (nIRQ and nFIQ) of the ARM Processor  Thirty-two individually maskable and vectored interrupt sources ̶ Source 0 is reserved for the Fast Interrupt Input (FIQ) ̶ Source 1 is reserved for system peripherals (PIT, RTT, PMC, DBGU, etc.) ̶ Programmable Edge-triggered or Level-sensitive Internal Sources ̶ Programmable Positive/Negative Edge-triggered or High/Low Level-sensitive  One External Sources plus the Fast Interrupt signal  8-level Priority Controller ̶ Drives the Normal Interrupt of the processor ̶ Handles priority of the interrupt sources 1 to 31 ̶ Higher priority interrupts can be served during service of lower priority interrupt  Vectoring ̶ Optimizes Interrupt Service Routine Branch and Execution ̶ One 32-bit Vector Register per interrupt source ̶ Interrupt Vector Register reads the corresponding current Interrupt Vector  Protect Mode ̶ Easy debugging by preventing automatic operations when protect modes are enabled  Fast Forcing ̶ Permits redirecting any normal interrupt source on the Fast Interrupt of the processor 398 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.3 Block Diagram Figure 27-1. Block Diagram FIQ AIC ARM Processor IRQ0-IRQn Up to Thirty-two nFIQ Embedded Sources PeEripmhbeeradlEdEed nIRQ PEermipbheerdadled Peripheral APB 27.4 Application Block Diagram Figure 27-2. Description of the Application Block OS-based Applications Standalone Applications OS Drivers RTOS Drivers Hard Real Time Tasks General OS Interrupt Handler Advanced Interrupt Controller External Peripherals Embedded Peripherals (External Interrupts) 27.5 AIC Detailed Block Diagram Figure 27-3. AIC Detailed Block Diagram Advanced Interrupt Controller ARM FIQ Processor Fast PIO External nFIQ Interrupt Controller Source Controller Input Stage nIRQ IRQ0-IRQn PIOIRQ FoFracsintg InPtreiorrruitpyt Processor Internal Controller Clock Source Input Power Embedded Stage Management Peripherals Controller User Interface Wake Up APB SAM9M11 [DATASHEET] 399 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.6 I/O Line Description Table 27-1. I/O Line Description Pin Name Pin Description Type FIQ Fast Interrupt Input IRQ0–IRQn Interrupt 0–Interrupt n Input 27.7 Product Dependencies 27.7.1 I/O Lines The interrupt signals FIQ and IRQ0 to IRQn are normally multiplexed through the PIO controllers. Depending on the features of the PIO controller used in the product, the pins must be programmed in accordance with their assigned interrupt function. This is not applicable when the PIO controller used in the product is transparent on the input path. Table 27-2. I/O Lines Instance Signal I/O Line Peripheral AIC FIQ PD19 B AIC IRQ PD18 B 27.7.2 Power Management The Advanced Interrupt Controller is continuously clocked. The Power Management Controller has no effect on the Advanced Interrupt Controller behavior. The assertion of the Advanced Interrupt Controller outputs, either nIRQ or nFIQ, wakes up the ARM processor while it is in Idle Mode. The General Interrupt Mask feature enables the AIC to wake up the processor without asserting the interrupt line of the processor, thus providing synchronization of the processor on an event. 27.7.3 Interrupt Sources The Interrupt Source 0 is always located at FIQ. If the product does not feature an FIQ pin, the Interrupt Source 0 cannot be used. The Interrupt Source 1 is always located at System Interrupt. This is the result of the OR-wiring of the system peripheral interrupt lines. When a system interrupt occurs, the service routine must first distinguish the cause of the interrupt. This is performed by reading successively the status registers of the above mentioned system peripherals. The interrupt sources 2 to 31 can either be connected to the interrupt outputs of an embedded user peripheral or to external interrupt lines. The external interrupt lines can be connected directly, or through the PIO Controller. The PIO Controllers are considered as user peripherals in the scope of interrupt handling. Accordingly, the PIO Controller interrupt lines are connected to the Interrupt Sources 2 to 31. The peripheral identification defined at the product level corresponds to the interrupt source number (as well as the bit number controlling the clock of the peripheral). Consequently, to simplify the description of the functional operations and the user interface, the interrupt sources are named FIQ, SYS, and PID2 to PID31. 400 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.8 Functional Description 27.8.1 Interrupt Source Control 27.8.1.1 Interrupt Source Mode The Advanced Interrupt Controller independently programs each interrupt source. The SRCTYPE field of the corresponding AIC_SMR (Source Mode Register) selects the interrupt condition of each source. The internal interrupt sources wired on the interrupt outputs of the embedded peripherals can be programmed either in level-sensitive mode or in edge-triggered mode. The active level of the internal interrupts is not important for the user. The external interrupt sources can be programmed either in high level-sensitive or low level-sensitive modes, or in positive edge-triggered or negative edge-triggered modes. 27.8.1.2 Interrupt Source Enabling Each interrupt source, including the FIQ in source 0, can be enabled or disabled by using the command registers; AIC_IECR (Interrupt Enable Command Register) and AIC_IDCR (Interrupt Disable Command Register). This set of registers conducts enabling or disabling in one instruction. The interrupt mask can be read in the AIC_IMR. A disabled interrupt does not affect servicing of other interrupts. 27.8.1.3 Interrupt Clearing and Setting All interrupt sources programmed to be edge-triggered (including the FIQ in source 0) can be individually set or cleared by writing respectively the AIC_ISCR and AIC_ICCR registers. Clearing or setting interrupt sources programmed in level-sensitive mode has no effect. The clear operation is perfunctory, as the software must perform an action to reinitialize the “memorization” circuitry activated when the source is programmed in edge-triggered mode. However, the set operation is available for auto-test or software debug purposes. It can also be used to execute an AIC-implementation of a software interrupt. The AIC features an automatic clear of the current interrupt when the AIC_IVR (Interrupt Vector Register) is read. Only the interrupt source being detected by the AIC as the current interrupt is affected by this operation. (See “Priority Controller” on page 404.) The automatic clear reduces the operations required by the interrupt service routine entry code to reading the AIC_IVR. Note that the automatic interrupt clear is disabled if the interrupt source has the Fast Forcing feature enabled as it is considered uniquely as a FIQ source. (For further details, See “Fast Forcing” on page 407.) The automatic clear of the interrupt source 0 is performed when AIC_FVR is read. 27.8.1.4 Interrupt Status For each interrupt, the AIC operation originates in AIC_IPR (Interrupt Pending Register) and its mask in AIC_IMR (Interrupt Mask Register). AIC_IPR enables the actual activity of the sources, whether masked or not. The AIC_ISR reads the number of the current interrupt (see “Priority Controller” on page 404) and the register AIC_CISR gives an image of the signals nIRQ and nFIQ driven on the processor. Each status referred to above can be used to optimize the interrupt handling of the systems. SAM9M11 [DATASHEET] 401 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.8.1.5 Internal Interrupt Source Input Stage Figure 27-4. Internal Interrupt Source Input Stage AIC_SMRI (SRCTYPE) Level/ AIC_IPR Source i Edge AIC_IMR Fast Interrupt Controller or Priority Controller Edge Detector AIC_IECR Set Clear FF AIC_ISCR AIC_ICCR AIC_IDCR 27.8.1.6 External Interrupt Source Input Stage Figure 27-5. External Interrupt Source Input Stage AIC_SMRi High/Low SRCTYPE Level/ AIC_IPR Edge AIC_IMR Source i Fast Interrupt Controller or Priority Controller Pos./Neg. AIC_IECR Edge Detector FF Set Clear AIC_ISCR AIC_IDCR AIC_ICCR 402 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.8.2 Interrupt Latencies Global interrupt latencies depend on several parameters, including:  The time the software masks the interrupts.  Occurrence, either at the processor level or at the AIC level.  The execution time of the instruction in progress when the interrupt occurs.  The treatment of higher priority interrupts and the resynchronization of the hardware signals. This section addresses only the hardware resynchronizations. It gives details of the latency times between the event on an external interrupt leading in a valid interrupt (edge or level) or the assertion of an internal interrupt source and the assertion of the nIRQ or nFIQ line on the processor. The resynchronization time depends on the programming of the interrupt source and on its type (internal or external). For the standard interrupt, resynchronization times are given assuming there is no higher priority in progress. The PIO Controller multiplexing has no effect on the interrupt latencies of the external interrupt sources. 27.8.2.1 External Interrupt Edge Triggered Source Figure 27-6. External Interrupt Edge Triggered Source MCK IRQ or FIQ (Positive Edge) IRQ or FIQ (Negative Edge) nIRQ Maximum IRQ Latency = 4 Cycles nFIQ Maximum FIQ Latency = 4 Cycles 27.8.2.2 External Interrupt Level Sensitive Source Figure 27-7. External Interrupt Level Sensitive Source MCK IRQ or FIQ (High Level) IRQ or FIQ (Low Level) nIRQ Maximum IRQ Latency = 3 Cycles nFIQ Maximum FIQ Latency = 3 cycles SAM9M11 [DATASHEET] 403 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.8.2.3 Internal Interrupt Edge Triggered Source Figure 27-8. Internal Interrupt Edge Triggered Source MCK nIRQ Maximum IRQ Latency = 4.5 Cycles Peripheral Interrupt Becomes Active 27.8.2.4 Internal Interrupt Level Sensitive Source Figure 27-9. Internal Interrupt Level Sensitive Source MCK nIRQ Maximum IRQ Latency = 3.5 Cycles Peripheral Interrupt Becomes Active 27.8.3 Normal Interrupt 27.8.3.1 Priority Controller An 8-level priority controller drives the nIRQ line of the processor, depending on the interrupt conditions occurring on the interrupt sources 1 to 31 (except for those programmed in Fast Forcing). Each interrupt source has a programmable priority level of 7 to 0, which is user-definable by writing the PRIOR field of the corresponding AIC_SMR (Source Mode Register). Level 7 is the highest priority and level 0 the lowest. As soon as an interrupt condition occurs, as defined by the SRCTYPE field of the AIC_SMR (Source Mode Register), the nIRQ line is asserted. As a new interrupt condition might have happened on other interrupt sources since the nIRQ has been asserted, the priority controller determines the current interrupt at the time the AIC_IVR (Interrupt Vector Register) is read. The read of AIC_IVR is the entry point of the interrupt handling which allows the AIC to consider that the interrupt has been taken into account by the software. The current priority level is defined as the priority level of the current interrupt. If several interrupt sources of equal priority are pending and enabled when the AIC_IVR is read, the interrupt with the lowest interrupt source number is serviced first. The nIRQ line can be asserted only if an interrupt condition occurs on an interrupt source with a higher priority. If an interrupt condition happens (or is pending) during the interrupt treatment in progress, it is delayed until the software indicates to the AIC the end of the current service by writing the AIC_EOICR (End of Interrupt Command Register). The write of AIC_EOICR is the exit point of the interrupt handling. 404 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.8.3.2 Interrupt Nesting The priority controller utilizes interrupt nesting in order for the high priority interrupt to be handled during the service of lower priority interrupts. This requires the interrupt service routines of the lower interrupts to re-enable the interrupt at the processor level. When an interrupt of a higher priority happens during an already occurring interrupt service routine, the nIRQ line is re-asserted. If the interrupt is enabled at the core level, the current execution is interrupted and the new interrupt service routine should read the AIC_IVR. At this time, the current interrupt number and its priority level are pushed into an embedded hardware stack, so that they are saved and restored when the higher priority interrupt servicing is finished and the AIC_EOICR is written. The AIC is equipped with an 8-level wide hardware stack in order to support up to eight interrupt nestings pursuant to having eight priority levels. 27.8.3.3 Interrupt Vectoring The interrupt handler addresses corresponding to each interrupt source can be stored in the registers AIC_SVR1 to AIC_SVR31 (Source Vector Register 1 to 31). When the processor reads AIC_IVR (Interrupt Vector Register), the value written into AIC_SVR corresponding to the current interrupt is returned. This feature offers a way to branch in one single instruction to the handler corresponding to the current interrupt, as AIC_IVR is mapped at the absolute address 0xFFFF F100 and thus accessible from the ARM interrupt vector at address 0x0000 0018 through the following instruction: LDR PC,[PC,# -&F20] When the processor executes this instruction, it loads the read value in AIC_IVR in its program counter, thus branching the execution on the correct interrupt handler. This feature is often not used when the application is based on an operating system (either real-time or not). Operating systems often have a single entry point for all the interrupts and the first task performed is to discern the source of the interrupt. However, it is strongly recommended to port the operating system on AT91 products by supporting the interrupt vectoring. This can be performed by defining all the AIC_SVR of the interrupt source to be handled by the operating system at the address of its interrupt handler. When doing so, the interrupt vectoring permits a critical interrupt to transfer the execution on a specific very fast handler and not onto the operating system’s general interrupt handler. This facilitates the support of hard real-time tasks (input/outputs of voice/audio buffers and software peripheral handling) to be handled efficiently and independently of the application running under an operating system. 27.8.3.4 Interrupt Handlers This section gives an overview of the fast interrupt handling sequence when using the AIC. It is assumed that the programmer understands the architecture of the ARM processor, and especially the processor interrupt modes and the associated status bits. It is assumed that: 1. The Advanced Interrupt Controller has been programmed, AIC_SVR registers are loaded with corresponding interrupt service routine addresses and interrupts are enabled. 2. The instruction at the ARM interrupt exception vector address is required to work with the vectoring LDR PC, [PC, # -&F20] When nIRQ is asserted, if the bit “I” of CPSR is 0, the sequence is as follows: 1. The CPSR is stored in SPSR_irq, the current value of the Program Counter is loaded in the Interrupt link register (R14_irq) and the Program Counter (R15) is loaded with 0x18. In the following cycle during fetch at address 0x1C, the ARM core adjusts R14_irq, decrementing it by four. 2. The ARM core enters Interrupt mode, if it has not already done so. SAM9M11 [DATASHEET] 405 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

3. When the instruction loaded at address 0x18 is executed, the program counter is loaded with the value read in AIC_IVR. Reading the AIC_IVR has the following effects: ̶ Sets the current interrupt to be the pending and enabled interrupt with the highest priority. The current level is the priority level of the current interrupt. ̶ De-asserts the nIRQ line on the processor. Even if vectoring is not used, AIC_IVR must be read in order to de-assert nIRQ. ̶ Automatically clears the interrupt, if it has been programmed to be edge-triggered. ̶ Pushes the current level and the current interrupt number on to the stack. ̶ Returns the value written in the AIC_SVR corresponding to the current interrupt. 4. The previous step has the effect of branching to the corresponding interrupt service routine. This should start by saving the link register (R14_irq) and SPSR_IRQ. The link register must be decremented by four when it is saved if it is to be restored directly into the program counter at the end of the interrupt. For example, the instruction SUB PC, LR, #4 may be used. 5. Further interrupts can then be unmasked by clearing the “I” bit in CPSR, allowing re-assertion of the nIRQ to be taken into account by the core. This can happen if an interrupt with a higher priority than the current interrupt occurs. 6. The interrupt handler can then proceed as required, saving the registers that will be used and restoring them at the end. During this phase, an interrupt of higher priority than the current level will restart the sequence from step 1. Note: If the interrupt is programmed to be level sensitive, the source of the interrupt must be cleared during this phase. 7. The “I” bit in CPSR must be set in order to mask interrupts before exiting to ensure that the interrupt is completed in an orderly manner. 8. The End of Interrupt Command Register (AIC_EOICR) must be written in order to indicate to the AIC that the current interrupt is finished. This causes the current level to be popped from the stack, restoring the previous current level if one exists on the stack. If another interrupt is pending, with lower or equal priority than the old current level but with higher priority than the new current level, the nIRQ line is re-asserted, but the interrupt sequence does not immediately start because the “I” bit is set in the core. SPSR_irq is restored. Finally, the saved value of the link register is restored directly into the PC. This has the effect of returning from the interrupt to whatever was being executed before, and of loading the CPSR with the stored SPSR, masking or unmasking the interrupts depending on the state saved in SPSR_irq. Note: The “I” bit in SPSR is significant. If it is set, it indicates that the ARM core was on the verge of masking an interrupt when the mask instruction was interrupted. Hence, when SPSR is restored, the mask instruction is completed (interrupt is masked). 27.8.4 Fast Interrupt 27.8.4.1 Fast Interrupt Source The interrupt source 0 is the only source which can raise a fast interrupt request to the processor except if fast forcing is used. The interrupt source 0 is generally connected to a FIQ pin of the product, either directly or through a PIO Controller. 27.8.4.2 Fast Interrupt Control The fast interrupt logic of the AIC has no priority controller. The mode of interrupt source 0 is programmed with the AIC_SMR0 and the field PRIOR of this register is not used even if it reads what has been written. The field SRCTYPE of AIC_SMR0 enables programming the fast interrupt source to be positive-edge triggered or negative- edge triggered or high-level sensitive or low-level sensitive Writing 0x1 in the AIC_IECR (Interrupt Enable Command Register) and AIC_IDCR (Interrupt Disable Command Register) respectively enables and disables the fast interrupt. The bit 0 of AIC_IMR (Interrupt Mask Register) indicates whether the fast interrupt is enabled or disabled. 406 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.8.4.3 Fast Interrupt Vectoring The fast interrupt handler address can be stored in AIC_SVR0 (Source Vector Register0). The value written into this register is returned when the processor reads AIC_FVR (Fast Vector Register). This offers a way to branch in one single instruction to the interrupt handler, as AIC_FVR is mapped at the absolute address 0xFFFF F104 and thus accessible from the ARM fast interrupt vector at address 0x0000 001C through the following instruction: LDR PC,[PC,# -&F20] When the processor executes this instruction it loads the value read in AIC_FVR in its program counter, thus branching the execution on the fast interrupt handler. It also automatically performs the clear of the fast interrupt source if it is programmed in edge-triggered mode. 27.8.4.4 Fast Interrupt Handlers This section gives an overview of the fast interrupt handling sequence when using the AIC. It is assumed that the programmer understands the architecture of the ARM processor, and especially the processor interrupt modes and associated status bits. Assuming that: 1. The Advanced Interrupt Controller has been programmed, AIC_SVR0 is loaded with the fast interrupt service routine address, and the interrupt source 0 is enabled. 2. The Instruction at address 0x1C (FIQ exception vector address) is required to vector the fast interrupt: LDR PC, [PC, # -&F20] 3. The user does not need nested fast interrupts. When nFIQ is asserted, if the bit “F” of CPSR is 0, the sequence is: 1. The CPSR is stored in SPSR_fiq, the current value of the program counter is loaded in the FIQ link register (R14_FIQ) and the program counter (R15) is loaded with 0x1C. In the following cycle, during fetch at address 0x20, the ARM core adjusts R14_fiq, decrementing it by four. 2. The ARM core enters FIQ mode. 3. When the instruction loaded at address 0x1C is executed, the program counter is loaded with the value read in AIC_FVR. Reading the AIC_FVR has effect of automatically clearing the fast interrupt, if it has been programmed to be edge triggered. In this case only, it de-asserts the nFIQ line on the processor. 4. The previous step enables branching to the corresponding interrupt service routine. It is not necessary to save the link register R14_fiq and SPSR_fiq if nested fast interrupts are not needed. 5. The Interrupt Handler can then proceed as required. It is not necessary to save registers R8 to R13 because FIQ mode has its own dedicated registers and the user R8 to R13 are banked. The other registers, R0 to R7, must be saved before being used, and restored at the end (before the next step). Note that if the fast interrupt is programmed to be level sensitive, the source of the interrupt must be cleared during this phase in order to de-assert the interrupt source 0. 6. Finally, the Link Register R14_fiq is restored into the PC after decrementing it by four (with instruction SUB PC, LR, #4 for example). This has the effect of returning from the interrupt to whatever was being executed before, loading the CPSR with the SPSR and masking or unmasking the fast interrupt depending on the state saved in the SPSR. Note: The “F” bit in SPSR is significant. If it is set, it indicates that the ARM core was just about to mask FIQ interrupts when the mask instruction was interrupted. Hence when the SPSR is restored, the interrupted instruction is completed (FIQ is masked). Another way to handle the fast interrupt is to map the interrupt service routine at the address of the ARM vector 0x1C. This method does not use the vectoring, so that reading AIC_FVR must be performed at the very beginning of the handler operation. However, this method saves the execution of a branch instruction. 27.8.4.5 Fast Forcing The Fast Forcing feature of the advanced interrupt controller provides redirection of any normal Interrupt source on the fast interrupt controller. SAM9M11 [DATASHEET] 407 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Fast Forcing is enabled or disabled by writing to the Fast Forcing Enable Register (AIC_FFER) and the Fast Forcing Disable Register (AIC_FFDR). Writing to these registers results in an update of the Fast Forcing Status Register (AIC_FFSR) that controls the feature for each internal or external interrupt source. When Fast Forcing is disabled, the interrupt sources are handled as described in the previous pages. When Fast Forcing is enabled, the edge/level programming and, in certain cases, edge detection of the interrupt source is still active but the source cannot trigger a normal interrupt to the processor and is not seen by the priority handler. If the interrupt source is programmed in level-sensitive mode and an active level is sampled, Fast Forcing results in the assertion of the nFIQ line to the core. If the interrupt source is programmed in edge-triggered mode and an active edge is detected, Fast Forcing results in the assertion of the nFIQ line to the core. The Fast Forcing feature does not affect the Source 0 pending bit in the Interrupt Pending Register (AIC_IPR). The FIQ Vector Register (AIC_FVR) reads the contents of the Source Vector Register 0 (AIC_SVR0), whatever the source of the fast interrupt may be. The read of the FVR does not clear the Source 0 when the fast forcing feature is used and the interrupt source should be cleared by writing to the Interrupt Clear Command Register (AIC_ICCR). All enabled and pending interrupt sources that have the fast forcing feature enabled and that are programmed in edge-triggered mode must be cleared by writing to the Interrupt Clear Command Register. In doing so, they are cleared independently and thus lost interrupts are prevented. The read of AIC_IVR does not clear the source that has the fast forcing feature enabled. The source 0, reserved to the fast interrupt, continues operating normally and becomes one of the Fast Interrupt sources. Figure 27-10. Fast Forcing _ Source 0 FIQ AIC_IPR Input Stage Automatic Clear AIC_IMR nFIQ Read FVR if Fast Forcing is disabled on Sources 1 to 31. AIC_FFSR Source n AIC_IPR Input Stage Priority Manager Automatic Clear AIC_IMR nIRQ Read IVR if Source n is the current interrupt and if Fast Forcing is disabled on Source n. 27.8.5 Protect Mode The Protect Mode permits reading the Interrupt Vector Register without performing the associated automatic operations. This is necessary when working with a debug system. When a debugger, working either with a Debug Monitor or the ARM processor's ICE, stops the applications and updates the opened windows, it might read the AIC User Interface and thus the IVR. This has undesirable consequences:  If an enabled interrupt with a higher priority than the current one is pending, it is stacked.  If there is no enabled pending interrupt, the spurious vector is returned. 408 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

In either case, an End of Interrupt command is necessary to acknowledge and to restore the context of the AIC. This operation is generally not performed by the debug system as the debug system would become strongly intrusive and cause the application to enter an undesired state. This is avoided by using the Protect Mode. Writing PROT in AIC_DCR (Debug Control Register) at 0x1 enables the Protect Mode. When the Protect Mode is enabled, the AIC performs interrupt stacking only when a write access is performed on the AIC_IVR. Therefore, the Interrupt Service Routines must write (arbitrary data) to the AIC_IVR just after reading it. The new context of the AIC, including the value of the Interrupt Status Register (AIC_ISR), is updated with the current interrupt only when AIC_IVR is written. An AIC_IVR read on its own (e.g., by a debugger), modifies neither the AIC context nor the AIC_ISR. Extra AIC_IVR reads perform the same operations. However, it is recommended to not stop the processor between the read and the write of AIC_IVR of the interrupt service routine to make sure the debugger does not modify the AIC context. To summarize, in normal operating mode, the read of AIC_IVR performs the following operations within the AIC: 1. Calculates active interrupt (higher than current or spurious). 2. Determines and returns the vector of the active interrupt. 3. Memorizes the interrupt. 4. Pushes the current priority level onto the internal stack. 5. Acknowledges the interrupt. However, while the Protect Mode is activated, only operations 1 to 3 are performed when AIC_IVR is read. Operations 4 and 5 are only performed by the AIC when AIC_IVR is written. Software that has been written and debugged using the Protect Mode runs correctly in Normal Mode without modification. However, in Normal Mode the AIC_IVR write has no effect and can be removed to optimize the code. 27.8.6 Spurious Interrupt The Advanced Interrupt Controller features protection against spurious interrupts. A spurious interrupt is defined as being the assertion of an interrupt source long enough for the AIC to assert the nIRQ, but no longer present when AIC_IVR is read. This is most prone to occur when:  An external interrupt source is programmed in level-sensitive mode and an active level occurs for only a short time.  An internal interrupt source is programmed in level sensitive and the output signal of the corresponding embedded peripheral is activated for a short time. (As in the case for the Watchdog.)  An interrupt occurs just a few cycles before the software begins to mask it, thus resulting in a pulse on the interrupt source. The AIC detects a spurious interrupt at the time the AIC_IVR is read while no enabled interrupt source is pending. When this happens, the AIC returns the value stored by the programmer in AIC_SPU (Spurious Vector Register). The programmer must store the address of a spurious interrupt handler in AIC_SPU as part of the application, to enable an as fast as possible return to the normal execution flow. This handler writes in AIC_EOICR and performs a return from interrupt. 27.8.7 General Interrupt Mask The AIC features a General Interrupt Mask bit to prevent interrupts from reaching the processor. Both the nIRQ and the nFIQ lines are driven to their inactive state if the bit GMSK in AIC_DCR (Debug Control Register) is set. However, this mask does not prevent waking up the processor if it has entered Idle Mode. This function facilitates synchronizing the processor on a next event and, as soon as the event occurs, performs subsequent operations without having to handle an interrupt. It is strongly recommended to use this mask with caution. SAM9M11 [DATASHEET] 409 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9 Advanced Interrupt Controller (AIC) User Interface 27.9.1 Base Address The AIC is mapped at the address 0xFFFF F000. It has a total 4-Kbyte addressing space. This permits the vectoring fea- ture, as the PC-relative load/store instructions of the ARM processor support only a ± 4-Kbyte offset. Table 27-3. Register Mapping Offset Register Name Access Reset 0x00 Source Mode Register 0 AIC_SMR0 Read/Write 0x0 0x04 Source Mode Register 1 AIC_SMR1 Read/Write 0x0 ... ... ... ... ... 0x7C Source Mode Register 31 AIC_SMR31 Read/Write 0x0 0x80 Source Vector Register 0 AIC_SVR0 Read/Write 0x0 0x84 Source Vector Register 1 AIC_SVR1 Read/Write 0x0 ... ... ... ... ... 0xFC Source Vector Register 31 AIC_SVR31 Read/Write 0x0 0x100 Interrupt Vector Register AIC_IVR Read-only 0x0 0x104 FIQ Interrupt Vector Register AIC_FVR Read-only 0x0 0x108 Interrupt Status Register AIC_ISR Read-only 0x0 0x10C Interrupt Pending Register(2) AIC_IPR Read-only 0x0(1) 0x110 Interrupt Mask Register(2) AIC_IMR Read-only 0x0 0x114 Core Interrupt Status Register AIC_CISR Read-only 0x0 0x118–0x11C Reserved – – – 0x120 Interrupt Enable Command Register(2) AIC_IECR Write-only – 0x124 Interrupt Disable Command Register(2) AIC_IDCR Write-only – 0x128 Interrupt Clear Command Register(2) AIC_ICCR Write-only – 0x12C Interrupt Set Command Register(2) AIC_ISCR Write-only – 0x130 End of Interrupt Command Register AIC_EOICR Write-only – 0x134 Spurious Interrupt Vector Register AIC_SPU Read/Write 0x0 0x138 Debug Control Register AIC_DCR Read/Write 0x0 0x13C Reserved – – – 0x140 Fast Forcing Enable Register(2) AIC_FFER Write-only – 0x144 Fast Forcing Disable Register(2) AIC_FFDR Write-only – 0x148 Fast Forcing Status Register(2) AIC_FFSR Read-only 0x0 0x14C–0x1E0 Reserved – – – 0x1EC–0x1FC Reserved – – – Notes: 1. The reset value of this register depends on the level of the external interrupt source. All other sources are cleared at reset, thus not pending. 2. PID2...PID31 bit fields refer to the identifiers as defined in the “Peripheral Identifiers” section of the product datasheet. 3. Values in the Version Register vary with the version of the IP block implementation. 410 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.2 AIC Source Mode Register Name: AIC_SMR0..AIC_SMR31 Address: 0xFFFFF000 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – SRCTYPE – – PRIOR • PRIOR: Priority Level Programs the priority level for all sources except FIQ source (source 0). The priority level can be between 0 (lowest) and 7 (highest). The priority level is not used for the FIQ in the related SMR register AIC_SMRx. • SRCTYPE: Interrupt Source Type The active level or edge is not programmable for the internal interrupt sources. SRCTYPE Internal Interrupt Sources External Interrupt Sources 0 0 High level Sensitive Low level Sensitive 0 1 Positive edge triggered Negative edge triggered 1 0 High level Sensitive High level Sensitive 1 1 Positive edge triggered Positive edge triggered SAM9M11 [DATASHEET] 411 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.3 AIC Source Vector Register Name: AIC_SVR0..AIC_SVR31 Address: 0xFFFFF080 Access: Read/Write 31 30 29 28 27 26 25 24 VECTOR 23 22 21 20 19 18 17 16 VECTOR 15 14 13 12 11 10 9 8 VECTOR 7 6 5 4 3 2 1 0 VECTOR • VECTOR: Source Vector The user may store in these registers the addresses of the corresponding handler for each interrupt source. 412 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.4 AIC Interrupt Vector Register Name: AIC_IVR Address: 0xFFFFF100 Access: Read-only 31 30 29 28 27 26 25 24 IRQV 23 22 21 20 19 18 17 16 IRQV 15 14 13 12 11 10 9 8 IRQV 7 6 5 4 3 2 1 0 IRQV • IRQV: Interrupt Vector Register The Interrupt Vector Register contains the vector programmed by the user in the Source Vector Register corresponding to the current interrupt. The Source Vector Register is indexed using the current interrupt number when the Interrupt Vector Register is read. When there is no current interrupt, the Interrupt Vector Register reads the value stored in AIC_SPU. SAM9M11 [DATASHEET] 413 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.5 AIC FIQ Vector Register Name: AIC_FVR Address: 0xFFFFF104 Access: Read-only 31 30 29 28 27 26 25 24 FIQV 23 22 21 20 19 18 17 16 FIQV 15 14 13 12 11 10 9 8 FIQV 7 6 5 4 3 2 1 0 FIQV • FIQV: FIQ Vector Register The FIQ Vector Register contains the vector programmed by the user in the Source Vector Register 0. When there is no fast interrupt, the FIQ Vector Register reads the value stored in AIC_SPU. 414 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.6 AIC Interrupt Status Register Name: AIC_ISR Address: 0xFFFFF108 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – IRQID • IRQID: Current Interrupt Identifier The Interrupt Status Register returns the current interrupt source number. SAM9M11 [DATASHEET] 415 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.7 AIC Interrupt Pending Register Name: AIC_IPR Address: 0xFFFFF10C Access: Read-only 31 30 29 28 27 26 25 24 PID31 PID30 PID29 PID28 PID27 PID26 PID25 PID24 23 22 21 20 19 18 17 16 PID23 PID22 PID21 PID20 PID19 PID18 PID17 PID16 15 14 13 12 11 10 9 8 PID15 PID14 PID13 PID12 PID11 PID10 PID9 PID8 7 6 5 4 3 2 1 0 PID7 PID6 PID5 PID4 PID3 PID2 SYS FIQ • FIQ, SYS, PID2–PID31: Interrupt Pending 0: Corresponding interrupt is not pending. 1: Corresponding interrupt is pending. 416 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.8 AIC Interrupt Mask Register Name: AIC_IMR Address: 0xFFFFF110 Access: Read-only 31 30 29 28 27 26 25 24 PID31 PID30 PID29 PID28 PID27 PID26 PID25 PID24 23 22 21 20 19 18 17 16 PID23 PID22 PID21 PID20 PID19 PID18 PID17 PID16 15 14 13 12 11 10 9 8 PID15 PID14 PID13 PID12 PID11 PID10 PID9 PID8 7 6 5 4 3 2 1 0 PID7 PID6 PID5 PID4 PID3 PID2 SYS FIQ • FIQ, SYS, PID2–PID31: Interrupt Mask 0: Corresponding interrupt is disabled. 1: Corresponding interrupt is enabled. SAM9M11 [DATASHEET] 417 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.9 AIC Core Interrupt Status Register Name: AIC_CISR Address: 0xFFFFF114 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – NIRQ NFIQ • NFIQ: NFIQ Status 0: nFIQ line is deactivated. 1: nFIQ line is active. • NIRQ: NIRQ Status 0: nIRQ line is deactivated. 1: nIRQ line is active. 418 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.10AIC Interrupt Enable Command Register Name: AIC_IECR Address: 0xFFFFF120 Access: Write-only 31 30 29 28 27 26 25 24 PID31 PID30 PID29 PID28 PID27 PID26 PID25 PID24 23 22 21 20 19 18 17 16 PID23 PID22 PID21 PID20 PID19 PID18 PID17 PID16 15 14 13 12 11 10 9 8 PID15 PID14 PID13 PID12 PID11 PID10 PID9 PID8 7 6 5 4 3 2 1 0 PID7 PID6 PID5 PID4 PID3 PID2 SYS FIQ • FIQ, SYS, PID2–PID31: Interrupt Enable 0: No effect. 1: Enables corresponding interrupt. SAM9M11 [DATASHEET] 419 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.11 AIC Interrupt Disable Command Register Name: AIC_IDCR Address: 0xFFFFF124 Access: Write-only 31 30 29 28 27 26 25 24 PID31 PID30 PID29 PID28 PID27 PID26 PID25 PID24 23 22 21 20 19 18 17 16 PID23 PID22 PID21 PID20 PID19 PID18 PID17 PID16 15 14 13 12 11 10 9 8 PID15 PID14 PID13 PID12 PID11 PID10 PID9 PID8 7 6 5 4 3 2 1 0 PID7 PID6 PID5 PID4 PID3 PID2 SYS FIQ • FIQ, SYS, PID2–PID31: Interrupt Disable 0: No effect. 1: Disables corresponding interrupt. 420 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.12AIC Interrupt Clear Command Register Name: AIC_ICCR Address: 0xFFFFF128 Access: Write-only 31 30 29 28 27 26 25 24 PID31 PID30 PID29 PID28 PID27 PID26 PID25 PID24 23 22 21 20 19 18 17 16 PID23 PID22 PID21 PID20 PID19 PID18 PID17 PID16 15 14 13 12 11 10 9 8 PID15 PID14 PID13 PID12 PID11 PID10 PID9 PID8 7 6 5 4 3 2 1 0 PID7 PID6 PID5 PID4 PID3 PID2 SYS FIQ • FIQ, SYS, PID2–PID31: Interrupt Clear 0: No effect. 1: Clears corresponding interrupt. SAM9M11 [DATASHEET] 421 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.13AIC Interrupt Set Command Register Name: AIC_ISCR Address: 0xFFFFF12C Access: Write-only 31 30 29 28 27 26 25 24 PID31 PID30 PID29 PID28 PID27 PID26 PID25 PID24 23 22 21 20 19 18 17 16 PID23 PID22 PID21 PID20 PID19 PID18 PID17 PID16 15 14 13 12 11 10 9 8 PID15 PID14 PID13 PID12 PID11 PID10 PID9 PID8 7 6 5 4 3 2 1 0 PID7 PID6 PID5 PID4 PID3 PID2 SYS FIQ • FIQ, SYS, PID2–PID31: Interrupt Set 0: No effect. 1: Sets corresponding interrupt. 422 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.14AIC End of Interrupt Command Register Name: AIC_EOICR Address: 0xFFFFF130 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – – The End of Interrupt Command Register is used by the interrupt routine to indicate that the interrupt treatment is complete. Any value can be written because it is only necessary to make a write to this register location to signal the end of interrupt treatment. SAM9M11 [DATASHEET] 423 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.15AIC Spurious Interrupt Vector Register Name: AIC_SPU Address: 0xFFFFF134 Access: Read/Write 31 30 29 28 27 26 25 24 SIVR 23 22 21 20 19 18 17 16 SIVR 15 14 13 12 11 10 9 8 SIVR 7 6 5 4 3 2 1 0 SIVR • SIVR: Spurious Interrupt Vector Register The user may store the address of a spurious interrupt handler in this register. The written value is returned in AIC_IVR in case of a spurious interrupt and in AIC_FVR in case of a spurious fast interrupt. 424 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.16AIC Debug Control Register Name: AIC_DCR Address: 0xFFFFF138 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – GMSK PROT • PROT: Protection Mode 0: The Protection Mode is disabled. 1: The Protection Mode is enabled. • GMSK: General Mask 0: The nIRQ and nFIQ lines are normally controlled by the AIC. 1: The nIRQ and nFIQ lines are tied to their inactive state. SAM9M11 [DATASHEET] 425 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.17AIC Fast Forcing Enable Register Name: AIC_FFER Address: 0xFFFFF140 Access: Write-only 31 30 29 28 27 26 25 24 PID31 PID30 PID29 PID28 PID27 PID26 PID25 PID24 23 22 21 20 19 18 17 16 PID23 PID22 PID21 PID20 PID19 PID18 PID17 PID16 15 14 13 12 11 10 9 8 PID15 PID14 PID13 PID12 PID11 PID10 PID9 PID8 7 6 5 4 3 2 1 0 PID7 PID6 PID5 PID4 PID3 PID2 SYS – • SYS, PID2–PID31: Fast Forcing Enable 0: No effect. 1: Enables the fast forcing feature on the corresponding interrupt. 426 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.18AIC Fast Forcing Disable Register Name: AIC_FFDR Address: 0xFFFFF144 Access: Write-only 31 30 29 28 27 26 25 24 PID31 PID30 PID29 PID28 PID27 PID26 PID25 PID24 23 22 21 20 19 18 17 16 PID23 PID22 PID21 PID20 PID19 PID18 PID17 PID16 15 14 13 12 11 10 9 8 PID15 PID14 PID13 PID12 PID11 PID10 PID9 PID8 7 6 5 4 3 2 1 0 PID7 PID6 PID5 PID4 PID3 PID2 SYS – • SYS, PID2–PID31: Fast Forcing Disable 0: No effect. 1: Disables the Fast Forcing feature on the corresponding interrupt. SAM9M11 [DATASHEET] 427 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9.19AIC Fast Forcing Status Register Name: AIC_FFSR Address: 0xFFFFF148 Access: Read-only 31 30 29 28 27 26 25 24 PID31 PID30 PID29 PID28 PID27 PID26 PID25 PID24 23 22 21 20 19 18 17 16 PID23 PID22 PID21 PID20 PID19 PID18 PID17 PID16 15 14 13 12 11 10 9 8 PID15 PID14 PID13 PID12 PID11 PID10 PID9 PID8 7 6 5 4 3 2 1 0 PID7 PID6 PID5 PID4 PID3 PID2 SYS – • SYS, PID2–PID31: Fast Forcing Status 0: The Fast Forcing feature is disabled on the corresponding interrupt. 1: The Fast Forcing feature is enabled on the corresponding interrupt. 428 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28. Debug Unit (DBGU) 28.1 Description The Debug Unit provides a single entry point from the processor for access to all the debug capabilities of Atmel’s ARM-based systems. The Debug Unit features a two-pin UART that can be used for several debug and trace purposes and offers an ideal medium for in-situ programming solutions and debug monitor communications. The Debug Unit two-pin UART can be used stand-alone for general purpose serial communication. Moreover, the association with two peripheral data controller channels permits packet handling for these tasks with processor time reduced to a minimum. The Debug Unit also makes the Debug Communication Channel (DCC) signals provided by the In-circuit Emulator of the ARM processor visible to the software. These signals indicate the status of the DCC read and write registers and generate an interrupt to the ARM processor, making possible the handling of the DCC under interrupt control. Chip Identifier registers permit recognition of the device and its revision. These registers inform as to the sizes and types of the on-chip memories, as well as the set of embedded peripherals. Finally, the Debug Unit features a Force NTRST capability that enables the software to decide whether to prevent access to the system via the In-circuit Emulator. This permits protection of the code, stored in ROM. 28.2 Embedded Characteristics  Composed of two functions ̶ Two-pin UART ̶ Debug Communication Channel (DCC) support  Two-pin UART ̶ Implemented features are 100% compatible with the standard Atmel USART ̶ Independent receiver and transmitter with a common programmable Baud Rate Generator ̶ Even, Odd, Mark or Space Parity Generation ̶ Parity, Framing and Overrun Error Detection ̶ Automatic Echo, Local Loopback and Remote Loopback Channel Modes ̶ Support for two PDC channels with connection to receiver and transmitter  Debug Communication Channel Support ̶ Offers visibility of an interrupt trigger from COMMRX and COMMTX signals from the ARM Processor’s ICE Interface SAM9M11 [DATASHEET] 429 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.3 Block Diagram Figure 28-1. Debug Unit Functional Block Diagram Peripheral Bridge Peripheral DMA Controller APB Debug Unit DTXD Transmit Power Parallel MCK Baud Rate Management Input/ Generator Controller Output Receive DRXD COMMRX DCC Chip ID ARM Handler COMMTX Processor nTRST ICE Interrupt Access dbgu_irq Control Handler Power-on Reset force_ntrst Table 28-1. Debug Unit Pin Description Pin Name Description Type DRXD Debug Receive Data Input DTXD Debug Transmit Data Output Figure 28-2. Debug Unit Application Example Boot Program Debug Monitor Trace Manager Debug Unit RS232 Drivers Programming Tool Debug Console Trace Console 430 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.4 Product Dependencies 28.4.1 I/O Lines Depending on product integration, the Debug Unit pins may be multiplexed with PIO lines. In this case, the programmer must first configure the corresponding PIO Controller to enable I/O lines operations of the Debug Unit. Table 28-2. I/O Lines Instance Signal I/O Line Peripheral DBGU DRXD PB12 A DBGU DTXD PB13 A 28.4.2 Power Management Depending on product integration, the Debug Unit clock may be controllable through the Power Management Controller. In this case, the programmer must first configure the PMC to enable the Debug Unit clock. Usually, the peripheral identifier used for this purpose is 1. 28.4.3 Interrupt Source Depending on product integration, the Debug Unit interrupt line is connected to one of the interrupt sources of the Advanced Interrupt Controller. Interrupt handling requires programming of the AIC before configuring the Debug Unit. Usually, the Debug Unit interrupt line connects to the interrupt source 1 of the AIC, which may be shared with the real-time clock, the system timer interrupt lines and other system peripheral interrupts, as shown in Figure 28- 1. This sharing requires the programmer to determine the source of the interrupt when the source 1 is triggered. 28.5 UART Operations The Debug Unit operates as a UART, (asynchronous mode only) and supports only 8-bit character handling (with parity). It has no clock pin. The Debug Unit's UART is made up of a receiver and a transmitter that operate independently, and a common baud rate generator. Receiver timeout and transmitter time guard are not implemented. However, all the implemented features are compatible with those of a standard USART. 28.5.1 Baud Rate Generator The baud rate generator provides the bit period clock named Baud Rate Clock to both the receiver and the transmitter. The Baud Rate Clock is the master clock divided by 16 times the value (CD) written in DBGU_BRGR (Baud Rate Generator Register). If DBGU_BRGR is set to 0, the Baud Rate Clock is disabled and the Debug Unit's UART remains inactive. The maximum allowable baud rate is Master Clock divided by 16. The minimum allowable baud rate is Master Clock divided by (16 x 65536). MCK Baud Rate = -------------------- 16×CD SAM9M11 [DATASHEET] 431 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 28-3. Baud Rate Generator CD CD MCK 16-bit Counter OUT >1 1 Divide Baud Rate by 16 Clock 0 0 Receiver Sampling Clock 28.5.2 Receiver 28.5.2.1 Receiver Reset, Enable and Disable After device reset, the Debug Unit receiver is disabled and must be enabled before being used. The receiver can be enabled by writing the control register DBGU_CR with the bit RXEN at 1. At this command, the receiver starts looking for a start bit. The programmer can disable the receiver by writing DBGU_CR with the bit RXDIS at 1. If the receiver is waiting for a start bit, it is immediately stopped. However, if the receiver has already detected a start bit and is receiving the data, it waits for the stop bit before actually stopping its operation. The programmer can also put the receiver in its reset state by writing DBGU_CR with the bit RSTRX at 1. In doing so, the receiver immediately stops its current operations and is disabled, whatever its current state. If RSTRX is applied when data is being processed, this data is lost. 28.5.2.2 Start Detection and Data Sampling The Debug Unit only supports asynchronous operations, and this affects only its receiver. The Debug Unit receiver detects the start of a received character by sampling the DRXD signal until it detects a valid start bit. A low level (space) on DRXD is interpreted as a valid start bit if it is detected for more than 7 cycles of the sampling clock, which is 16 times the baud rate. Hence, a space that is longer than 7/16 of the bit period is detected as a valid start bit. A space which is 7/16 of a bit period or shorter is ignored and the receiver continues to wait for a valid start bit. When a valid start bit has been detected, the receiver samples the DRXD at the theoretical midpoint of each bit. It is assumed that each bit lasts 16 cycles of the sampling clock (1-bit period) so the bit sampling point is eight cycles (0.5-bit period) after the start of the bit. The first sampling point is therefore 24 cycles (1.5-bit periods) after the falling edge of the start bit was detected. Each subsequent bit is sampled 16 cycles (1-bit period) after the previous one. Figure 28-4. Start Bit Detection Sampling Clock DRXD True Start D0 Detection Baud Rate Clock 432 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 28-5. Character Reception Example: 8-bit, parity enabled 1 stop 0.5 bit 1 bit period period DRXD Sampling D0 D1 D2 D3 D4 D5 D6 D7 Stop Bit True Start Detection Parity Bit 28.5.2.3 Receiver Ready When a complete character is received, it is transferred to the DBGU_RHR and the RXRDY status bit in DBGU_SR (Status Register) is set. The bit RXRDY is automatically cleared when the receive holding register DBGU_RHR is read. Figure 28-6. Receiver Ready DRXD S D0 D1 D2 D3 D4 D5 D6 D7 P S D0 D1 D2 D3 D4 D5 D6 D7 P RXRDY Read DBGU_RHR 28.5.2.4 Receiver Overrun If DBGU_RHR has not been read by the software (or the Peripheral Data Controller) since the last transfer, the RXRDY bit is still set and a new character is received, the OVRE status bit in DBGU_SR is set. OVRE is cleared when the software writes the control register DBGU_CR with the bit RSTSTA (Reset Status) at 1. Figure 28-7. Receiver Overrun DRXD S D0 D1 D2 D3 D4 D5 D6 D7 P stop S D0 D1 D2 D3 D4 D5 D6 D7 P stop RXRDY OVRE RSTSTA 28.5.2.5 Parity Error Each time a character is received, the receiver calculates the parity of the received data bits, in accordance with the field PAR in DBGU_MR. It then compares the result with the received parity bit. If different, the parity error bit PARE in DBGU_SR is set at the same time the RXRDY is set. The parity bit is cleared when the control register DBGU_CR is written with the bit RSTSTA (Reset Status) at 1. If a new character is received before the reset status command is written, the PARE bit remains at 1. Figure 28-8. Parity Error DRXD S D0 D1 D2 D3 D4 D5 D6 D7 P stop RXRDY PARE Wrong Parity Bit RSTSTA SAM9M11 [DATASHEET] 433 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.5.2.6 Receiver Framing Error When a start bit is detected, it generates a character reception when all the data bits have been sampled. The stop bit is also sampled and when it is detected at 0, the FRAME (Framing Error) bit in DBGU_SR is set at the same time the RXRDY bit is set. The bit FRAME remains high until the control register DBGU_CR is written with the bit RSTSTA at 1. Figure 28-9. Receiver Framing Error DRXD S D0 D1 D2 D3 D4 D5 D6 D7 P stop RXRDY FRAME Stop Bit RSTSTA Detected at 0 28.5.3 Transmitter 28.5.3.1 Transmitter Reset, Enable and Disable After device reset, the Debug Unit transmitter is disabled and it must be enabled before being used. The transmitter is enabled by writing the control register DBGU_CR with the bit TXEN at 1. From this command, the transmitter waits for a character to be written in the Transmit Holding Register DBGU_THR before actually starting the transmission. The programmer can disable the transmitter by writing DBGU_CR with the bit TXDIS at 1. If the transmitter is not operating, it is immediately stopped. However, if a character is being processed into the Shift Register and/or a character has been written in the Transmit Holding Register, the characters are completed before the transmitter is actually stopped. The programmer can also put the transmitter in its reset state by writing the DBGU_CR with the bit RSTTX at 1. This immediately stops the transmitter, whether or not it is processing characters. 28.5.3.2 Transmit Format The Debug Unit transmitter drives the pin DTXD at the baud rate clock speed. The line is driven depending on the format defined in the Mode Register and the data stored in the Shift Register. One start bit at level 0, then the 8 data bits, from the lowest to the highest bit, one optional parity bit and one stop bit at 1 are consecutively shifted out as shown on the following figure. The field PARE in the mode register DBGU_MR defines whether or not a parity bit is shifted out. When a parity bit is enabled, it can be selected between an odd parity, an even parity, or a fixed space or mark bit. Figure 28-10. Character Transmission Example: Parity enabled Baud Rate Clock DTXD Start D0 D1 D2 D3 D4 D5 D6 D7 Parity Stop Bit Bit Bit 434 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.5.3.3 Transmitter Control When the transmitter is enabled, the bit TXRDY (Transmitter Ready) is set in the status register DBGU_SR. The transmission starts when the programmer writes in the Transmit Holding Register DBGU_THR, and after the written character is transferred from DBGU_THR to the Shift Register. The bit TXRDY remains high until a second character is written in DBGU_THR. As soon as the first character is completed, the last character written in DBGU_THR is transferred into the shift register and TXRDY rises again, showing that the holding register is empty. When both the Shift Register and the DBGU_THR are empty, i.e., all the characters written in DBGU_THR have been processed, the bit TXEMPTY rises after the last stop bit has been completed. Figure 28-11. Transmitter Control DBGU_THR Data 0 Data 1 Shift Register Data 0 Data 1 DTXD S Data 0 P stop S Data 1 P stop TXRDY TXEMPTY Write Data 0 Write Data 1 in DBGU_THR in DBGU_THR 28.5.4 Peripheral Data Controller Both the receiver and the transmitter of the Debug Unit's UART are generally connected to a Peripheral Data Controller (PDC) channel. The peripheral data controller channels are programmed via registers that are mapped within the Debug Unit user interface from the offset 0x100. The status bits are reported in the Debug Unit status register DBGU_SR and can generate an interrupt. The RXRDY bit triggers the PDC channel data transfer of the receiver. This results in a read of the data in DBGU_RHR. The TXRDY bit triggers the PDC channel data transfer of the transmitter. This results in a write of a data in DBGU_THR. 28.5.5 Test Modes The Debug Unit supports three tests modes. These modes of operation are programmed by using the field CHMODE (Channel Mode) in the mode register DBGU_MR. The Automatic Echo mode allows bit-by-bit retransmission. When a bit is received on the DRXD line, it is sent to the DTXD line. The transmitter operates normally, but has no effect on the DTXD line. The Local Loopback mode allows the transmitted characters to be received. DTXD and DRXD pins are not used and the output of the transmitter is internally connected to the input of the receiver. The DRXD pin level has no effect and the DTXD line is held high, as in idle state. The Remote Loopback mode directly connects the DRXD pin to the DTXD line. The transmitter and the receiver are disabled and have no effect. This mode allows a bit-by-bit retransmission. SAM9M11 [DATASHEET] 435 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 28-12. Test Modes Automatic Echo Receiver RXD Disabled Transmitter TXD Local Loopback Disabled Receiver RXD VDD Disabled Transmitter TXD Remote Loopback VDD Disabled Receiver RXD Disabled Transmitter TXD 28.5.6 Debug Communication Channel Support The Debug Unit handles the signals COMMRX and COMMTX that come from the Debug Communication Channel of the ARM Processor and are driven by the In-circuit Emulator. The Debug Communication Channel contains two registers that are accessible through the ICE Breaker on the JTAG side and through the coprocessor 0 on the ARM Processor side. As a reminder, the following instructions are used to read and write the Debug Communication Channel: MRC p14, 0, Rd, c1, c0, 0 Returns the debug communication data read register into Rd MCR p14, 0, Rd, c1, c0, 0 Writes the value in Rd to the debug communication data write register. The bits COMMRX and COMMTX, which indicate, respectively, that the read register has been written by the debugger but not yet read by the processor, and that the write register has been written by the processor and not yet read by the debugger, are wired on the two highest bits of the status register DBGU_SR. These bits can generate an interrupt. This feature permits handling under interrupt a debug link between a debug monitor running on the target system and a debugger. 436 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.5.7 Chip Identifier The Debug Unit features two chip identifier registers, DBGU_CIDR (Chip ID Register) and DBGU_EXID (Extension ID). Both registers contain a hard-wired value that is read-only. The first register contains the following fields:  EXT - shows the use of the extension identifier register  NVPTYP and NVPSIZ - identifies the type of embedded non-volatile memory and its size  ARCH - identifies the set of embedded peripherals  SRAMSIZ - indicates the size of the embedded SRAM  EPROC - indicates the embedded ARM processor  VERSION - gives the revision of the silicon The second register is device-dependent and reads 0 if the bit EXT is 0. 28.5.8 ICE Access Prevention The Debug Unit allows blockage of access to the system through the ARM processor's ICE interface. This feature is implemented via the register Force NTRST (DBGU_FNR), that allows assertion of the NTRST signal of the ICE Interface. Writing the bit FNTRST (Force NTRST) to 1 in this register prevents any activity on the TAP controller. On standard devices, the bit FNTRST resets to 0 and thus does not prevent ICE access. This feature is especially useful on custom ROM devices for customers who do not want their on-chip code to be visible. SAM9M11 [DATASHEET] 437 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.6 Debug Unit (DBGU) User Interface Table 28-3. Register Mapping Offset Register Name Access Reset 0x0000 Control Register DBGU_CR Write-only – 0x0004 Mode Register DBGU_MR Read/Write 0x0 0x0008 Interrupt Enable Register DBGU_IER Write-only – 0x000C Interrupt Disable Register DBGU_IDR Write-only – 0x0010 Interrupt Mask Register DBGU_IMR Read-only 0x0 0x0014 Status Register DBGU_SR Read-only – 0x0018 Receive Holding Register DBGU_RHR Read-only 0x0 0x001C Transmit Holding Register DBGU_THR Write-only – 0x0020 Baud Rate Generator Register DBGU_BRGR Read/Write 0x0 0x0024–0x003C Reserved – – – 0x0040 Chip ID Register DBGU_CIDR Read-only – 0x0044 Chip ID Extension Register DBGU_EXID Read-only – 0x0048 Force NTRST Register DBGU_FNR Read/Write 0x0 0x004C–0x00FC Reserved – – – 0x0100–0x0124 PDC Area – – – 438 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.6.1 Debug Unit Control Register Name: DBGU_CR Address: 0xFFFFEE00 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – RSTSTA 7 6 5 4 3 2 1 0 TXDIS TXEN RXDIS RXEN RSTTX RSTRX – – • RSTRX: Reset Receiver 0: No effect. 1: The receiver logic is reset and disabled. If a character is being received, the reception is aborted. • RSTTX: Reset Transmitter 0: No effect. 1: The transmitter logic is reset and disabled. If a character is being transmitted, the transmission is aborted. • RXEN: Receiver Enable 0: No effect. 1: The receiver is enabled if RXDIS is 0. • RXDIS: Receiver Disable 0: No effect. 1: The receiver is disabled. If a character is being processed and RSTRX is not set, the character is completed before the receiver is stopped. • TXEN: Transmitter Enable 0: No effect. 1: The transmitter is enabled if TXDIS is 0. • TXDIS: Transmitter Disable 0: No effect. 1: The transmitter is disabled. If a character is being processed and a character has been written the DBGU_THR and RSTTX is not set, both characters are completed before the transmitter is stopped. • RSTSTA: Reset Status Bits 0: No effect. 1: Resets the status bits PARE, FRAME and OVRE in the DBGU_SR. SAM9M11 [DATASHEET] 439 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.6.2 Debug Unit Mode Register Name: DBGU_MR Address: 0xFFFFEE04 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 CHMODE – – PAR – 7 6 5 4 3 2 1 0 – – – – – – – – • PAR: Parity Type PAR Parity Type 0 0 0 Even parity 0 0 1 Odd parity 0 1 0 Space: parity forced to 0 0 1 1 Mark: parity forced to 1 1 x x No parity • CHMODE: Channel Mode CHMODE Mode Description 0 0 Normal Mode 0 1 Automatic Echo 1 0 Local Loopback 1 1 Remote Loopback 440 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.6.3 Debug Unit Interrupt Enable Register Name: DBGU_IER Address: 0xFFFFEE08 Access: Write-only 31 30 29 28 27 26 25 24 COMMRX COMMTX – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – RXBUFF TXBUFE – TXEMPTY – 7 6 5 4 3 2 1 0 PARE FRAME OVRE ENDTX ENDRX – TXRDY RXRDY • RXRDY: Enable RXRDY Interrupt • TXRDY: Enable TXRDY Interrupt • ENDRX: Enable End of Receive Transfer Interrupt • ENDTX: Enable End of Transmit Interrupt • OVRE: Enable Overrun Error Interrupt • FRAME: Enable Framing Error Interrupt • PARE: Enable Parity Error Interrupt • TXEMPTY: Enable TXEMPTY Interrupt • TXBUFE: Enable Buffer Empty Interrupt • RXBUFF: Enable Buffer Full Interrupt • COMMTX: Enable COMMTX (from ARM) Interrupt • COMMRX: Enable COMMRX (from ARM) Interrupt 0: No effect. 1: Enables the corresponding interrupt. SAM9M11 [DATASHEET] 441 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.6.4 Debug Unit Interrupt Disable Register Name: DBGU_IDR Address: 0xFFFFEE0C Access: Write-only 31 30 29 28 27 26 25 24 COMMRX COMMTX – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – RXBUFF TXBUFE – TXEMPTY – 7 6 5 4 3 2 1 0 PARE FRAME OVRE ENDTX ENDRX – TXRDY RXRDY • RXRDY: Disable RXRDY Interrupt • TXRDY: Disable TXRDY Interrupt • ENDRX: Disable End of Receive Transfer Interrupt • ENDTX: Disable End of Transmit Interrupt • OVRE: Disable Overrun Error Interrupt • FRAME: Disable Framing Error Interrupt • PARE: Disable Parity Error Interrupt • TXEMPTY: Disable TXEMPTY Interrupt • TXBUFE: Disable Buffer Empty Interrupt • RXBUFF: Disable Buffer Full Interrupt • COMMTX: Disable COMMTX (from ARM) Interrupt • COMMRX: Disable COMMRX (from ARM) Interrupt 0: No effect. 1: Disables the corresponding interrupt. 442 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.6.5 Debug Unit Interrupt Mask Register Name: DBGU_IMR Address: 0xFFFFEE10 Access: Read-only 31 30 29 28 27 26 25 24 COMMRX COMMTX – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – RXBUFF TXBUFE – TXEMPTY – 7 6 5 4 3 2 1 0 PARE FRAME OVRE ENDTX ENDRX – TXRDY RXRDY • RXRDY: Mask RXRDY Interrupt • TXRDY: Disable TXRDY Interrupt • ENDRX: Mask End of Receive Transfer Interrupt • ENDTX: Mask End of Transmit Interrupt • OVRE: Mask Overrun Error Interrupt • FRAME: Mask Framing Error Interrupt • PARE: Mask Parity Error Interrupt • TXEMPTY: Mask TXEMPTY Interrupt • TXBUFE: Mask TXBUFE Interrupt • RXBUFF: Mask RXBUFF Interrupt • COMMTX: Mask COMMTX Interrupt • COMMRX: Mask COMMRX Interrupt 0: The corresponding interrupt is disabled. 1: The corresponding interrupt is enabled. SAM9M11 [DATASHEET] 443 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.6.6 Debug Unit Status Register Name: DBGU_SR Address: 0xFFFFEE14 Access: Read-only 31 30 29 28 27 26 25 24 COMMRX COMMTX – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – RXBUFF TXBUFE – TXEMPTY – 7 6 5 4 3 2 1 0 PARE FRAME OVRE ENDTX ENDRX – TXRDY RXRDY • RXRDY: Receiver Ready 0: No character has been received since the last read of the DBGU_RHR or the receiver is disabled. 1: At least one complete character has been received, transferred to DBGU_RHR and not yet read. • TXRDY: Transmitter Ready 0: A character has been written to DBGU_THR and not yet transferred to the Shift Register, or the transmitter is disabled. 1: There is no character written to DBGU_THR not yet transferred to the Shift Register. • ENDRX: End of Receiver Transfer 0: The End of Transfer signal from the receiver Peripheral Data Controller channel is inactive. 1: The End of Transfer signal from the receiver Peripheral Data Controller channel is active. • ENDTX: End of Transmitter Transfer 0: The End of Transfer signal from the transmitter Peripheral Data Controller channel is inactive. 1: The End of Transfer signal from the transmitter Peripheral Data Controller channel is active. • OVRE: Overrun Error 0: No overrun error has occurred since the last RSTSTA. 1: At least one overrun error has occurred since the last RSTSTA. • FRAME: Framing Error 0: No framing error has occurred since the last RSTSTA. 1: At least one framing error has occurred since the last RSTSTA. • PARE: Parity Error 0: No parity error has occurred since the last RSTSTA. 1: At least one parity error has occurred since the last RSTSTA. • TXEMPTY: Transmitter Empty 0: There are characters in DBGU_THR, or characters being processed by the transmitter, or the transmitter is disabled. 1: There are no characters in DBGU_THR and there are no characters being processed by the transmitter. 444 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• TXBUFE: Transmission Buffer Empty 0: The buffer empty signal from the transmitter PDC channel is inactive. 1: The buffer empty signal from the transmitter PDC channel is active. • RXBUFF: Receive Buffer Full 0: The buffer full signal from the receiver PDC channel is inactive. 1: The buffer full signal from the receiver PDC channel is active. • COMMTX: Debug Communication Channel Write Status 0: COMMTX from the ARM processor is inactive. 1: COMMTX from the ARM processor is active. • COMMRX: Debug Communication Channel Read Status 0: COMMRX from the ARM processor is inactive. 1: COMMRX from the ARM processor is active. SAM9M11 [DATASHEET] 445 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.6.7 Debug Unit Receiver Holding Register Name: DBGU_RHR Address: 0xFFFFEE18 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 RXCHR • RXCHR: Received Character Last received character if RXRDY is set. 446 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.6.8 Debug Unit Transmit Holding Register Name: DBGU_THR Address: 0xFFFFEE1C Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 TXCHR • TXCHR: Character to be Transmitted Next character to be transmitted after the current character if TXRDY is not set. SAM9M11 [DATASHEET] 447 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.6.9 Debug Unit Baud Rate Generator Register Name: DBGU_BRGR Address: 0xFFFFEE20 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 CD 7 6 5 4 3 2 1 0 CD • CD: Clock Divisor CD Baud Rate Clock 0 Disabled 1 MCK 2–65535 MCK / (CD x 16) 448 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.6.10Debug Unit Chip ID Register Name: DBGU_CIDR Address: 0xFFFFEE40 Access: Read-only 31 30 29 28 27 26 25 24 EXT NVPTYP ARCH 23 22 21 20 19 18 17 16 ARCH SRAMSIZ 15 14 13 12 11 10 9 8 NVPSIZ2 NVPSIZ 7 6 5 4 3 2 1 0 EPROC VERSION • VERSION: Version of the Device Values depend upon the version of the device. • EPROC: Embedded Processor EPROC Processor 0 0 1 ARM946ES 0 1 0 ARM7TDMI 1 0 0 ARM920T 1 0 1 ARM926EJS • NVPSIZ: Nonvolatile Program Memory Size NVPSIZ Size 0 0 0 0 None 0 0 0 1 8 Kbytes 0 0 1 0 16 Kbytes 0 0 1 1 32 Kbytes 0 1 0 0 Reserved 0 1 0 1 64 Kbytes 0 1 1 0 Reserved 0 1 1 1 128 Kbytes 1 0 0 0 Reserved 1 0 0 1 256 Kbytes 1 0 1 0 512 Kbytes 1 0 1 1 Reserved 1 1 0 0 1024 Kbytes 1 1 0 1 Reserved 1 1 1 0 2048 Kbytes 1 1 1 1 Reserved SAM9M11 [DATASHEET] 449 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• NVPSIZ2 Second Nonvolatile Program Memory Size NVPSIZ2 Size 0 0 0 0 None 0 0 0 1 8 Kbytes 0 0 1 0 16 Kbytes 0 0 1 1 32 Kbytes 0 1 0 0 Reserved 0 1 0 1 64 Kbytes 0 1 1 0 Reserved 0 1 1 1 128 Kbytes 1 0 0 0 Reserved 1 0 0 1 256 Kbytes 1 0 1 0 512 Kbytes 1 0 1 1 Reserved 1 1 0 0 1024 Kbytes 1 1 0 1 Reserved 1 1 1 0 2048 Kbytes 1 1 1 1 Reserved • SRAMSIZ: Internal SRAM Size SRAMSIZ Size 0 0 0 0 Reserved 0 0 0 1 1 Kbytes 0 0 1 0 2 Kbytes 0 0 1 1 6 Kbytes 0 1 0 0 112 Kbytes 0 1 0 1 4 Kbytes 0 1 1 0 80 Kbytes 0 1 1 1 160 Kbytes 1 0 0 0 8 Kbytes 1 0 0 1 16 Kbytes 1 0 1 0 32 Kbytes 1 0 1 1 64 Kbytes 1 1 0 0 128 Kbytes 1 1 0 1 256 Kbytes 1 1 1 0 96 Kbytes 1 1 1 1 512 Kbytes 450 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• ARCH: Architecture Identifier ARCH Hex Bin Architecture 0x19 0001 1001 AT91SAM9xx Series 0x29 0010 1001 AT91SAM9XExx Series 0x34 0011 0100 AT91x34 Series 0x37 0011 0111 CAP7 Series 0x39 0011 1001 CAP9 Series 0x3B 0011 1011 CAP11 Series 0x40 0100 0000 AT91x40 Series 0x42 0100 0010 AT91x42 Series 0x55 0101 0101 AT91x55 Series 0x60 0110 0000 AT91SAM7Axx Series 0x61 0110 0001 AT91SAM7AQxx Series 0x63 0110 0011 AT91x63 Series 0x70 0111 0000 AT91SAM7Sxx Series 0x71 0111 0001 AT91SAM7XCxx Series 0x72 0111 0010 AT91SAM7SExx Series 0x73 0111 0011 AT91SAM7Lxx Series 0x75 0111 0101 AT91SAM7Xxx Series 0x92 1001 0010 AT91x92 Series 0xF0 1111 0000 AT75Cxx Series • NVPTYP: Nonvolatile Program Memory Type NVPTYP Memory 0 0 0 ROM 0 0 1 ROMless or on-chip Flash 1 0 0 SRAM emulating ROM 0 1 0 Embedded Flash Memory ROM and Embedded Flash Memory 0 1 1 NVPSIZ is ROM size NVPSIZ2 is Flash size • EXT: Extension Flag 0: Chip ID has a single register definition without extension 1: An extended Chip ID exists. SAM9M11 [DATASHEET] 451 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.6.11 Debug Unit Chip ID Extension Register Name: DBGU_EXID Address: 0xFFFFEE44 Access: Read-only 31 30 29 28 27 26 25 24 EXID 23 22 21 20 19 18 17 16 EXID 15 14 13 12 11 10 9 8 EXID 7 6 5 4 3 2 1 0 EXID • EXID: Chip ID Extension Reads 0 if the bit EXT in DBGU_CIDR is 0. 452 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

28.6.12Debug Unit Force NTRST Register Name: DBGU_FNR Address: 0xFFFFEE48 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – FNTRST • FNTRST: Force NTRST 0: NTRST of the ARM processor’s TAP controller is driven by the power_on_reset signal. 1: NTRST of the ARM processor’s TAP controller is held low. SAM9M11 [DATASHEET] 453 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29. Parallel Input/Output Controller (PIO) 29.1 Description The Parallel Input/Output Controller (PIO) manages up to 32 fully programmable input/output lines. Each I/O line may be dedicated as a general-purpose I/O or be assigned to a function of an embedded peripheral. This assures effective optimization of the pins of a product. Each I/O line is associated with a bit number in all of the 32-bit registers of the 32-bit wide User Interface. Each I/O line of the PIO Controller features:  An input change interrupt enabling level change detection on any I/O line.  A glitch filter providing rejection of pulses lower than one-half of clock cycle.  Multi-drive capability similar to an open drain I/O line.  Control of the pull-up of the I/O line.  Input visibility and output control. The PIO Controller also features a synchronous output providing up to 32 bits of data output in a single write operation. 454 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.2 Block Diagram Figure 29-1. Block Diagram PIO Controller PIO Interrupt AIC PIO Clock PMC Data, Enable Up to 32 peripheral IOs Embedded Peripheral PIN 0 Data, Enable PIN 1 Up to 32 pins Up to 32 peripheral IOs Embedded Peripheral PIN 31 APB Figure 29-2. Application Block Diagram On-Chip Peripheral Drivers Keyboard Driver Control & Command Driver On-Chip Peripherals PIO Controller Keyboard Driver General Purpose I/Os External Devices SAM9M11 [DATASHEET] 455 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.3 Product Dependencies 29.3.1 Pin Multiplexing Each pin is configurable, according to product definition as either a general-purpose I/O line only, or as an I/O line multiplexed with one or two peripheral I/Os. As the multiplexing is hardware-defined and thus product-dependent, the hardware designer and programmer must carefully determine the configuration of the PIO controllers required by their application. When an I/O line is general-purpose only, i.e., not multiplexed with any peripheral I/O, programming of the PIO Controller regarding the assignment to a peripheral has no effect and only the PIO Controller can control how the pin is driven by the product. 29.3.2 External Interrupt Lines The interrupt signals FIQ and IRQ0 to IRQn are most generally multiplexed through the PIO Controllers. However, it is not necessary to assign the I/O line to the interrupt function as the PIO Controller has no effect on inputs and the interrupt lines (FIQ or IRQs) are used only as inputs. 29.3.3 Power Management The Power Management Controller controls the PIO Controller clock in order to save power. Writing any of the registers of the user interface does not require the PIO Controller clock to be enabled. This means that the configuration of the I/O lines does not require the PIO Controller clock to be enabled. However, when the clock is disabled, not all of the features of the PIO Controller are available. Note that the Input Change Interrupt and the read of the pin level require the clock to be validated. After a hardware reset, the PIO clock is disabled by default. The user must configure the Power Management Controller before any access to the input line information. 29.3.4 Interrupt Generation For interrupt handling, the PIO Controllers are considered as user peripherals. This means that the PIO Controller interrupt lines are connected among the interrupt sources 2 to 31. Refer to the PIO Controller peripheral identifier in the product description to identify the interrupt sources dedicated to the PIO Controllers. The PIO Controller interrupt can be generated only if the PIO Controller clock is enabled. 456 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.4 Functional Description The PIO Controller features up to 32 fully-programmable I/O lines. Most of the control logic associated to each I/O is represented in Figure 29-3. In this description each signal shown represents but one of up to 32 possible indexes. Figure 29-3. I/O Line Control Logic PIO_OER[0] PIO_OSR[0] PIO_PUER[0] PIO_ODR[0] PIO_PUSR[0] PIO_PUDR[0] 1 Peripheral A Output Enable 0 0 Peripheral B 0 Output Enable 1 PIO_ASR[0] PIO_PER[0] PIO_ABSR[0] PIO_PSR[0] 1 PIO_BSR[0] PIO_PDR[0] PIO_MDER[0] Peripheral A 0 PIO_MDSR[0] Output 0 PIO_MDDR[0] Peripheral B 1 PIO_SODR[0] 0 Output PIO_ODSR[0] 1 Pad PIO_CODR[0] 1 Peripheral A Input Peripheral B PIO_PDSR[0] PIO_ISR[0] Input 0 (Up to 32 possible inputs) Edge Detector Glitch 1 PIO Interrupt Filter PIO_IFER[0] PIO_IFSR[0] PIO_IER[0] PIO_IFDR[0] PIO_IMR[0] PIO_IDR[0] PIO_ISR[31] PIO_IER[31] PIO_IMR[31] PIO_IDR[31] SAM9M11 [DATASHEET] 457 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.4.1 Pull-up Resistor Control Each I/O line is designed with an embedded pull-up resistor. The pull-up resistor can be enabled or disabled by writing respectively PIO_PUER (Pull-up Enable Register) and PIO_PUDR (Pull-up Disable Resistor). Writing in these registers results in setting or clearing the corresponding bit in PIO_PUSR (Pull-up Status Register). Reading a 1 in PIO_PUSR means the pull-up is disabled and reading a 0 means the pull-up is enabled. Control of the pull-up resistor is possible regardless of the configuration of the I/O line. After reset, all of the pull-ups are enabled, i.e., PIO_PUSR resets at the value 0x0. 29.4.2 I/O Line or Peripheral Function Selection When a pin is multiplexed with one or two peripheral functions, the selection is controlled with the registers PIO_PER (PIO Enable Register) and PIO_PDR (PIO Disable Register). The register PIO_PSR (PIO Status Register) is the result of the set and clear registers and indicates whether the pin is controlled by the corresponding peripheral or by the PIO Controller. A value of 0 indicates that the pin is controlled by the corresponding on-chip peripheral selected in the PIO_ABSR (AB Select Status Register). A value of 1 indicates the pin is controlled by the PIO controller. If a pin is used as a general purpose I/O line (not multiplexed with an on-chip peripheral), PIO_PER and PIO_PDR have no effect and PIO_PSR returns 1 for the corresponding bit. After reset, most generally, the I/O lines are controlled by the PIO controller, i.e., PIO_PSR resets at 1. However, in some events, it is important that PIO lines are controlled by the peripheral (as in the case of memory chip select lines that must be driven inactive after reset or for address lines that must be driven low for booting out of an external memory). Thus, the reset value of PIO_PSR is defined at the product level, depending on the multiplexing of the device. 29.4.3 Peripheral A or B Selection The PIO Controller provides multiplexing of up to two peripheral functions on a single pin. The selection is performed by writing PIO_ASR (A Select Register) and PIO_BSR (Select B Register). PIO_ABSR (AB Select Status Register) indicates which peripheral line is currently selected. For each pin, the corresponding bit at level 0 means peripheral A is selected whereas the corresponding bit at level 1 indicates that peripheral B is selected. Note that multiplexing of peripheral lines A and B only affects the output line. The peripheral input lines are always connected to the pin input. After reset, PIO_ABSR is 0, thus indicating that all the PIO lines are configured on peripheral A. However, peripheral A generally does not drive the pin as the PIO Controller resets in I/O line mode. Writing in PIO_ASR and PIO_BSR manages PIO_ABSR regardless of the configuration of the pin. However, assignment of a pin to a peripheral function requires a write in the corresponding peripheral selection register (PIO_ASR or PIO_BSR) in addition to a write in PIO_PDR. 29.4.4 Output Control When the I/0 line is assigned to a peripheral function, i.e., the corresponding bit in PIO_PSR is at 0, the drive of the I/O line is controlled by the peripheral. Peripheral A or B, depending on the value in PIO_ABSR, determines whether the pin is driven or not. When the I/O line is controlled by the PIO controller, the pin can be configured to be driven. This is done by writing PIO_OER (Output Enable Register) and PIO_ODR (Output Disable Register). The results of these write operations are detected in PIO_OSR (Output Status Register). When a bit in this register is at 0, the corresponding I/O line is used as an input only. When the bit is at1, the corresponding I/O line is driven by the PIO controller. The level driven on an I/O line can be determined by writing in PIO_SODR (Set Output Data Register) and PIO_CODR (Clear Output Data Register). These write operations respectively set and clear PIO_ODSR (Output Data Status Register), which represents the data driven on the I/O lines. Writing in PIO_OER and PIO_ODR 458 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

manages PIO_OSR whether the pin is configured to be controlled by the PIO controller or assigned to a peripheral function. This enables configuration of the I/O line prior to setting it to be managed by the PIO Controller. Similarly, writing in PIO_SODR and PIO_CODR effects PIO_ODSR. This is important as it defines the first level driven on the I/O line. 29.4.5 Synchronous Data Output Controlling all parallel busses using several PIOs requires two successive write operations in the PIO_SODR and PIO_CODR registers. This may lead to unexpected transient values. The PIO controller offers a direct control of PIO outputs by single write access to PIO_ODSR (Output Data Status Register). Only bits unmasked by PIO_OWSR (Output Write Status Register) are written. The mask bits in the PIO_OWSR are set by writing to PIO_OWER (Output Write Enable Register) and cleared by writing to PIO_OWDR (Output Write Disable Register). After reset, the synchronous data output is disabled on all the I/O lines as PIO_OWSR resets at 0x0. 29.4.6 Multi Drive Control (Open Drain) Each I/O can be independently programmed in Open Drain by using the Multi Drive feature. This feature permits several drivers to be connected on the I/O line which is driven low only by each device. An external pull-up resistor (or enabling of the internal one) is generally required to guarantee a high level on the line. The Multi Drive feature is controlled by PIO_MDER (Multi-driver Enable Register) and PIO_MDDR (Multi-driver Disable Register). The Multi Drive can be selected whether the I/O line is controlled by the PIO controller or assigned to a peripheral function. PIO_MDSR (Multi-driver Status Register) indicates the pins that are configured to support external drivers. After reset, the Multi Drive feature is disabled on all pins, i.e., PIO_MDSR resets at value 0x0. 29.4.7 Output Line Timings Figure 29-4 shows how the outputs are driven either by writing PIO_SODR or PIO_CODR, or by directly writing PIO_ODSR. This last case is valid only if the corresponding bit in PIO_OWSR is set. Figure 29-4 also shows when the feedback in PIO_PDSR is available. Figure 29-4. Output Line Timings MCK Write PIO_SODR APB Access Write PIO_ODSR at 1 Write PIO_CODR APB Access Write PIO_ODSR at 0 PIO_ODSR 2 cycles 2 cycles PIO_PDSR 29.4.8 Inputs The level on each I/O line can be read through PIO_PDSR (Pin Data Status Register). This register indicates the level of the I/O lines regardless of their configuration, whether uniquely as an input or driven by the PIO controller or driven by a peripheral. SAM9M11 [DATASHEET] 459 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Reading the I/O line levels requires the clock of the PIO controller to be enabled, otherwise PIO_PDSR reads the levels present on the I/O line at the time the clock was disabled. 29.4.9 Input Glitch Filtering Optional input glitch filters are independently programmable on each I/O line. When the glitch filter is enabled, a glitch with a duration of less than 1/2 Master Clock (MCK) cycle is automatically rejected, while a pulse with a duration of 1 Master Clock cycle or more is accepted. For pulse durations between 1/2 Master Clock cycle and 1 Master Clock cycle the pulse may or may not be taken into account, depending on the precise timing of its occurrence. Thus for a pulse to be visible it must exceed 1 Master Clock cycle, whereas for a glitch to be reliably filtered out, its duration must not exceed 1/2 Master Clock cycle. The filter introduces one Master Clock cycle latency if the pin level change occurs before a rising edge. However, this latency does not appear if the pin level change occurs before a falling edge. This is illustrated in Figure 29-5. The glitch filters are controlled by the register set; PIO_IFER (Input Filter Enable Register), PIO_IFDR (Input Filter Disable Register) and PIO_IFSR (Input Filter Status Register). Writing PIO_IFER and PIO_IFDR respectively sets and clears bits in PIO_IFSR. This last register enables the glitch filter on the I/O lines. When the glitch filter is enabled, it does not modify the behavior of the inputs on the peripherals. It acts only on the value read in PIO_PDSR and on the input change interrupt detection. The glitch filters require that the PIO Controller clock is enabled. Figure 29-5. Input Glitch Filter Timing MCK up to 1.5 cycles Pin Level 1 cycle 1 cycle 1 cycle 1 cycle PIO_PDSR if PIO_IFSR = 0 2 cycles 1 cycle PIO_PDSR up to 2.5 cycles up to 2 cycles if PIO_IFSR = 1 29.4.10Input Change Interrupt The PIO Controller can be programmed to generate an interrupt when it detects an input change on an I/O line. The Input Change Interrupt is controlled by writing PIO_IER (Interrupt Enable Register) and PIO_IDR (Interrupt Disable Register), which respectively enable and disable the input change interrupt by setting and clearing the corresponding bit in PIO_IMR (Interrupt Mask Register). As Input change detection is possible only by comparing two successive samplings of the input of the I/O line, the PIO Controller clock must be enabled. The Input Change Interrupt is available, regardless of the configuration of the I/O line, i.e., configured as an input only, controlled by the PIO Controller or assigned to a peripheral function. When an input change is detected on an I/O line, the corresponding bit in PIO_ISR (Interrupt Status Register) is set. If the corresponding bit in PIO_IMR is set, the PIO Controller interrupt line is asserted. The interrupt signals of the thirty-two channels are ORed-wired together to generate a single interrupt signal to the Advanced Interrupt Controller. When the software reads PIO_ISR, all the interrupts are automatically cleared. This signifies that all the interrupts that are pending when PIO_ISR is read must be handled. 460 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 29-6. Input Change Interrupt Timings MCK Pin Level PIO_ISR Read PIO_ISR APB Access APB Access 29.4.11 Write Protected Registers To prevent any single software error that may corrupt the PIO behavior, the registers listed below can be write- protected by setting the WPEN bit in the PIO Write Protect Mode Register (PIO_WPMR). If a write access in a write-protected register is detected, then the WPVS flag in the PIO Write Protect Status Register (PIO_WPSR) is set and the field WPVSRC indicates in which register the write access has been attempted. The WPVS flag is automatically reset after reading the PIO Write Protect Status Register (PIO_WPSR). List of the write-protected registers:  “PIO Enable Register” on page 466  “PIO Disable Register” on page 467  “PIO Output Enable Register” on page 469  “PIO Output Disable Register” on page 470  “PIO Input Filter Enable Register” on page 472  “PIO Input Filter Disable Register” on page 473  “PIO Set Output Data Register” on page 475  “PIO Clear Output Data Register” on page 476  “PIO Multi-driver Enable Register” on page 483  “PIO Multi-driver Disable Register” on page 484  “PIO Pull-up Disable Register” on page 486  “PIO Pull-up Enable Register” on page 487  “PIO Peripheral A Select Register” on page 489  “PIO Peripheral B Select Register” on page 490  “PIO Output Write Enable Register” on page 492  “PIO Output Write Disable Register” on page 493 SAM9M11 [DATASHEET] 461 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.4.12Programmable I/O Delays The PIO interface consists of a series of signals driven by peripherals or directly by software. The simultaneous switching outputs on these busses may lead to a peak of current in the internal and external power supply lines. In order to reduce the peak of current in such cases, additional propagation delays can be adjusted independently for pad buffers by means of configuration registers, PIO_DELAY. For each I/O, the additional programmable delays range from 0 to 4 ns (Worst Case PVT). The delay can differ between IOs supporting this feature. The delay can be modified according to programming for each I/O. The minimum additional delay that can be programmed on a PAD supporting this feature is 1/16 of the maximum programmable delay. Only PADs PC[12], PC[7:2], PA[30:23] and PA[9:2] can be configured. When programming 0x0 in fields, no delay is added (reset value) and the propagation delay of the pad buffers is the inherent delay of the pad buffer. When programming 0xF in field, the propagation delay of the corresponding pad is maximal. Figure 29-7. Programmable I/O Delays PAin[0] PIO PAout[0] Programmable Delay Line DELAY1 PAin[1] PAout[1] Programmable Delay Line DELAY2 PAin[2] PAout[2] Programmable Delay Line DELAYx 462 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.5 I/O Lines Programming Example The programing example as shown in Table 29-1 below is used to define the following configuration.  4-bit output port on I/O lines 0 to 3, (should be written in a single write operation), open-drain, with pull-up resistor  Four output signals on I/O lines 4 to 7 (to drive LEDs for example), driven high and low, no pull-up resistor  Four input signals on I/O lines 8 to 11 (to read push-button states for example), with pull-up resistors, glitch filters and input change interrupts  Four input signals on I/O line 12 to 15 to read an external device status (polled, thus no input change interrupt), no pull-up resistor, no glitch filter  I/O lines 16 to 19 assigned to peripheral A functions with pull-up resistor  I/O lines 20 to 23 assigned to peripheral B functions, no pull-up resistor  I/O line 24 to 27 assigned to peripheral A with Input Change Interrupt and pull-up resistor Table 29-1. Programming Example Register Value to be Written PIO_PER 0x0000 FFFF PIO_PDR 0x0FFF 0000 PIO_OER 0x0000 00FF PIO_ODR 0x0FFF FF00 PIO_IFER 0x0000 0F00 PIO_IFDR 0x0FFF F0FF PIO_SODR 0x0000 0000 PIO_CODR 0x0FFF FFFF PIO_IER 0x0F00 0F00 PIO_IDR 0x00FF F0FF PIO_MDER 0x0000 000F PIO_MDDR 0x0FFF FFF0 PIO_PUDR 0x00F0 00F0 PIO_PUER 0x0F0F FF0F PIO_ASR 0x0F0F 0000 PIO_BSR 0x00F0 0000 PIO_OWER 0x0000 000F PIO_OWDR 0x0FFF FFF0 SAM9M11 [DATASHEET] 463 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6 Parallel Input/Output Controller (PIO) User Interface Each I/O line controlled by the PIO Controller is associated with a bit in each of the PIO Controller User Interface registers. Each register is 32 bits wide. If a parallel I/O line is not defined, writing to the corresponding bits has no effect. Undefined bits read zero. If the I/O line is not multiplexed with any peripheral, the I/O line is controlled by the PIO Controller and PIO_PSR returns 1 systematically. Table 29-2. Register Mapping Offset Register Name Access Reset 0x0000 PIO Enable Register PIO_PER Write-only – 0x0004 PIO Disable Register PIO_PDR Write-only – 0x0008 PIO Status Register PIO_PSR Read-only (1) 0x000C Reserved 0x0010 Output Enable Register PIO_OER Write-only – 0x0014 Output Disable Register PIO_ODR Write-only – 0x0018 Output Status Register PIO_OSR Read-only 0x0000 0000 0x001C Reserved 0x0020 Glitch Input Filter Enable Register PIO_IFER Write-only – 0x0024 Glitch Input Filter Disable Register PIO_IFDR Write-only – 0x0028 Glitch Input Filter Status Register PIO_IFSR Read-only 0x0000 0000 0x002C Reserved 0x0030 Set Output Data Register PIO_SODR Write-only – 0x0034 Clear Output Data Register PIO_CODR Write-only Read-only 0x0038 Output Data Status Register PIO_ODSR or(2) – Read/Write 0x003C Pin Data Status Register PIO_PDSR Read-only (3) 0x0040 Interrupt Enable Register PIO_IER Write-only – 0x0044 Interrupt Disable Register PIO_IDR Write-only – 0x0048 Interrupt Mask Register PIO_IMR Read-only 0x00000000 0x004C Interrupt Status Register(4) PIO_ISR Read-only 0x00000000 0x0050 Multi-driver Enable Register PIO_MDER Write-only – 0x0054 Multi-driver Disable Register PIO_MDDR Write-only – 0x0058 Multi-driver Status Register PIO_MDSR Read-only 0x00000000 0x005C Reserved 0x0060 Pull-up Disable Register PIO_PUDR Write-only – 0x0064 Pull-up Enable Register PIO_PUER Write-only – 0x0068 Pad Pull-up Status Register PIO_PUSR Read-only 0x00000000 0x006C Reserved 0x0070 Peripheral A Select Register(5) PIO_ASR Write-only – 0x0074 Peripheral B Select Register(5) PIO_BSR Write-only – 0x0078 AB Status Register(5) PIO_ABSR Read-only 0x00000000 464 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 29-2. Register Mapping (Continued) Offset Register Name Access Reset 0x007C–0x009C Reserved 0x00A0 Output Write Enable PIO_OWER Write-only – 0x00A4 Output Write Disable PIO_OWDR Write-only – 0x00A8 Output Write Status Register PIO_OWSR Read-only 0x00000000 0x00AC Reserved 0x00C0 I/O Delay Register PIO_DELAY0R Read/Write 0x00000000 0x00C4 I/O Delay Register PIO_DELAY1R Read/Write 0x00000000 0x00C8 I/O Delay Register PIO_DELAY2R Read/Write 0x00000000 0x00CC I/O Delay Register PIO_DELAY3R Read/Write 0x00000000 0x00C4–0x00E0 Reserved 0x00E4 Write Protect Mode Register PIO_WPMR Read/Write 0x00000000 0x00E8 Write Protect Status Register PIO_WPSR Read-only 0x00000000 0x00F0–0x00F8 Reserved Notes: 1. Reset value of PIO_PSR depends on the product implementation. 2. PIO_ODSR is Read-only or Read/Write depending on PIO_OWSR I/O lines. 3. Reset value of PIO_PDSR depends on the level of the I/O lines. Reading the I/O line levels requires the clock of the PIO Controller to be enabled, otherwise PIO_PDSR reads the levels present on the I/O line at the time the clock was disabled. 4. PIO_ISR is reset at 0x0. However, the first read of the register may read a different value as input changes may have occurred. 5. Only this set of registers clears the status by writing 1 in the first register and sets the status by writing 1 in the second register. SAM9M11 [DATASHEET] 465 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.1 PIO Enable Register Name: PIO_PER Address: 0xFFFFF200 (PIOA), 0xFFFFF400 (PIOB), 0xFFFFF600 (PIOC), 0xFFFFF800 (PIOD), 0xFFFFFA00 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: PIO Enable 0: No effect. 1: Enables the PIO to control the corresponding pin (disables peripheral control of the pin). 466 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.2 PIO Disable Register Name: PIO_PDR Address: 0xFFFFF204 (PIOA), 0xFFFFF404 (PIOB), 0xFFFFF604 (PIOC), 0xFFFFF804 (PIOD), 0xFFFFFA04 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: PIO Disable 0: No effect. 1: Disables the PIO from controlling the corresponding pin (enables peripheral control of the pin). SAM9M11 [DATASHEET] 467 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.3 PIO Status Register Name: PIO_PSR Address: 0xFFFFF208 (PIOA), 0xFFFFF408 (PIOB), 0xFFFFF608 (PIOC), 0xFFFFF808 (PIOD), 0xFFFFFA08 (PIOE) Access: Read-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: PIO Status 0: PIO is inactive on the corresponding I/O line (peripheral is active). 1: PIO is active on the corresponding I/O line (peripheral is inactive). 468 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.4 PIO Output Enable Register Name: PIO_OER Address: 0xFFFFF210 (PIOA), 0xFFFFF410 (PIOB), 0xFFFFF610 (PIOC), 0xFFFFF810 (PIOD), 0xFFFFFA10 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Output Enable 0: No effect. 1: Enables the output on the I/O line. SAM9M11 [DATASHEET] 469 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.5 PIO Output Disable Register Name: PIO_ODR Address: 0xFFFFF214 (PIOA), 0xFFFFF414 (PIOB), 0xFFFFF614 (PIOC), 0xFFFFF814 (PIOD), 0xFFFFFA14 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Output Disable 0: No effect. 1: Disables the output on the I/O line. 470 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.6 PIO Output Status Register Name: PIO_OSR Address: 0xFFFFF218 (PIOA), 0xFFFFF418 (PIOB), 0xFFFFF618 (PIOC), 0xFFFFF818 (PIOD), 0xFFFFFA18 (PIOE) Access: Read-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Output Status 0: The I/O line is a pure input. 1: The I/O line is enabled in output. SAM9M11 [DATASHEET] 471 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.7 PIO Input Filter Enable Register Name: PIO_IFER Address: 0xFFFFF220 (PIOA), 0xFFFFF420 (PIOB), 0xFFFFF620 (PIOC), 0xFFFFF820 (PIOD), 0xFFFFFA20 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Input Filter Enable 0: No effect. 1: Enables the input glitch filter on the I/O line. 472 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.8 PIO Input Filter Disable Register Name: PIO_IFDR Address: 0xFFFFF224 (PIOA), 0xFFFFF424 (PIOB), 0xFFFFF624 (PIOC), 0xFFFFF824 (PIOD), 0xFFFFFA24 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Input Filter Disable 0: No effect. 1: Disables the input glitch filter on the I/O line. SAM9M11 [DATASHEET] 473 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.9 PIO Input Filter Status Register Name: PIO_IFSR Address: 0xFFFFF228 (PIOA), 0xFFFFF428 (PIOB), 0xFFFFF628 (PIOC), 0xFFFFF828 (PIOD), 0xFFFFFA28 (PIOE) Access: Read-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Input Filer Status 0: The input glitch filter is disabled on the I/O line. 1: The input glitch filter is enabled on the I/O line. 474 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.10PIO Set Output Data Register Name: PIO_SODR Address: 0xFFFFF230 (PIOA), 0xFFFFF430 (PIOB), 0xFFFFF630 (PIOC), 0xFFFFF830 (PIOD), 0xFFFFFA30 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Set Output Data 0: No effect. 1: Sets the data to be driven on the I/O line. SAM9M11 [DATASHEET] 475 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.11 PIO Clear Output Data Register Name: PIO_CODR Address: 0xFFFFF234 (PIOA), 0xFFFFF434 (PIOB), 0xFFFFF634 (PIOC), 0xFFFFF834 (PIOD), 0xFFFFFA34 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Clear Output Data 0: No effect. 1: Clears the data to be driven on the I/O line. 476 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.12PIO Output Data Status Register Name: PIO_ODSR Address: 0xFFFFF238 (PIOA), 0xFFFFF438 (PIOB), 0xFFFFF638 (PIOC), 0xFFFFF838 (PIOD), 0xFFFFFA38 (PIOE) Access: Read-only or Read/Write 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Output Data Status 0: The data to be driven on the I/O line is 0. 1: The data to be driven on the I/O line is 1. SAM9M11 [DATASHEET] 477 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.13PIO Pin Data Status Register Name: PIO_PDSR Address: 0xFFFFF23C (PIOA), 0xFFFFF43C (PIOB), 0xFFFFF63C (PIOC), 0xFFFFF83C (PIOD), 0xFFFFFA3C (PIOE) Access: Read-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Output Data Status 0: The I/O line is at level 0. 1: The I/O line is at level 1. 478 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.14PIO Interrupt Enable Register Name: PIO_IER Address: 0xFFFFF240 (PIOA), 0xFFFFF440 (PIOB), 0xFFFFF640 (PIOC), 0xFFFFF840 (PIOD), 0xFFFFFA40 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Input Change Interrupt Enable 0: No effect. 1: Enables the Input Change Interrupt on the I/O line. SAM9M11 [DATASHEET] 479 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.15PIO Interrupt Disable Register Name: PIO_IDR Address: 0xFFFFF244 (PIOA), 0xFFFFF444 (PIOB), 0xFFFFF644 (PIOC), 0xFFFFF844 (PIOD), 0xFFFFFA44 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Input Change Interrupt Disable 0: No effect. 1: Disables the Input Change Interrupt on the I/O line. 480 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.16PIO Interrupt Mask Register Name: PIO_IMR Address: 0xFFFFF248 (PIOA), 0xFFFFF448 (PIOB), 0xFFFFF648 (PIOC), 0xFFFFF848 (PIOD), 0xFFFFFA48 (PIOE) Access: Read-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Input Change Interrupt Mask 0: Input Change Interrupt is disabled on the I/O line. 1: Input Change Interrupt is enabled on the I/O line. SAM9M11 [DATASHEET] 481 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.17PIO Interrupt Status Register Name: PIO_ISR Address: 0xFFFFF24C (PIOA), 0xFFFFF44C (PIOB), 0xFFFFF64C (PIOC), 0xFFFFF84C (PIOD), 0xFFFFFA4C (PIOE) Access: Read-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Input Change Interrupt Status 0: No Input Change has been detected on the I/O line since PIO_ISR was last read or since reset. 1: At least one Input Change has been detected on the I/O line since PIO_ISR was last read or since reset. 482 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.18PIO Multi-driver Enable Register Name: PIO_MDER Address: 0xFFFFF250 (PIOA), 0xFFFFF450 (PIOB), 0xFFFFF650 (PIOC), 0xFFFFF850 (PIOD), 0xFFFFFA50 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Multi Drive Enable 0: No effect. 1: Enables Multi Drive on the I/O line. SAM9M11 [DATASHEET] 483 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.19PIO Multi-driver Disable Register Name: PIO_MDDR Address: 0xFFFFF254 (PIOA), 0xFFFFF454 (PIOB), 0xFFFFF654 (PIOC), 0xFFFFF854 (PIOD), 0xFFFFFA54 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Multi Drive Disable 0: No effect. 1: Disables Multi Drive on the I/O line. 484 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.20PIO Multi-driver Status Register Name: PIO_MDSR Address: 0xFFFFF258 (PIOA), 0xFFFFF458 (PIOB), 0xFFFFF658 (PIOC), 0xFFFFF858 (PIOD), 0xFFFFFA58 (PIOE) Access: Read-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Multi Drive Status 0: The Multi Drive is disabled on the I/O line. The pin is driven at high and low level. 1: The Multi Drive is enabled on the I/O line. The pin is driven at low level only. SAM9M11 [DATASHEET] 485 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.21PIO Pull-up Disable Register Name: PIO_PUDR Address: 0xFFFFF260 (PIOA), 0xFFFFF460 (PIOB), 0xFFFFF660 (PIOC), 0xFFFFF860 (PIOD), 0xFFFFFA60 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Pull-up Disable 0: No effect. 1: Disables the pull-up resistor on the I/O line. 486 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.22PIO Pull-up Enable Register Name: PIO_PUER Address: 0xFFFFF264 (PIOA), 0xFFFFF464 (PIOB), 0xFFFFF664 (PIOC), 0xFFFFF864 (PIOD), 0xFFFFFA64 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Pull-up Enable 0: No effect. 1: Enables the pull-up resistor on the I/O line. SAM9M11 [DATASHEET] 487 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.23PIO Pull-up Status Register Name: PIO_PUSR Address: 0xFFFFF268 (PIOA), 0xFFFFF468 (PIOB), 0xFFFFF668 (PIOC), 0xFFFFF868 (PIOD), 0xFFFFFA68 (PIOE) Access: Read-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Pull-up Status 0: Pull-up resistor is enabled on the I/O line. 1: Pull-up resistor is disabled on the I/O line. 488 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.24PIO Peripheral A Select Register Name: PIO_ASR Address: 0xFFFFF270 (PIOA), 0xFFFFF470 (PIOB), 0xFFFFF670 (PIOC), 0xFFFFF870 (PIOD), 0xFFFFFA70 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Peripheral A Select 0: No effect. 1: Assigns the I/O line to the Peripheral A function. SAM9M11 [DATASHEET] 489 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.25PIO Peripheral B Select Register Name: PIO_BSR Address: 0xFFFFF274 (PIOA), 0xFFFFF474 (PIOB), 0xFFFFF674 (PIOC), 0xFFFFF874 (PIOD), 0xFFFFFA74 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Peripheral B Select 0: No effect. 1: Assigns the I/O line to the peripheral B function. 490 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.26PIO Peripheral A B Status Register Name: PIO_ABSR Address: 0xFFFFF278 (PIOA), 0xFFFFF478 (PIOB), 0xFFFFF678 (PIOC), 0xFFFFF878 (PIOD), 0xFFFFFA78 (PIOE) Access: Read-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Peripheral A B Status 0: The I/O line is assigned to the Peripheral A. 1: The I/O line is assigned to the Peripheral B. SAM9M11 [DATASHEET] 491 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.27PIO Output Write Enable Register Name: PIO_OWER Address: 0xFFFFF2A0 (PIOA), 0xFFFFF4A0 (PIOB), 0xFFFFF6A0 (PIOC), 0xFFFFF8A0 (PIOD), 0xFFFFFAA0 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Output Write Enable 0: No effect. 1: Enables writing PIO_ODSR for the I/O line. 492 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.28PIO Output Write Disable Register Name: PIO_OWDR Address: 0xFFFFF2A4 (PIOA), 0xFFFFF4A4 (PIOB), 0xFFFFF6A4 (PIOC), 0xFFFFF8A4 (PIOD), 0xFFFFFAA4 (PIOE) Access: Write-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Output Write Disable 0: No effect. 1: Disables writing PIO_ODSR for the I/O line. SAM9M11 [DATASHEET] 493 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.29PIO Output Write Status Register Name: PIO_OWSR Address: 0xFFFFF2A8 (PIOA), 0xFFFFF4A8 (PIOB), 0xFFFFF6A8 (PIOC), 0xFFFFF8A8 (PIOD), 0xFFFFFAA8 (PIOE) Access: Read-only 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 • P0–P31: Output Write Status 0: Writing PIO_ODSR does not affect the I/O line. 1: Writing PIO_ODSR affects the I/O line. 494 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.30PIO I/O Delay Register Name: PIO_DELAYxR [x=0..3] Address: 0xFFFFF2C0 (PIOA), 0xFFFFF4C0 (PIOB), 0xFFFFF6C0 (PIOC), 0xFFFFF8C0 (PIOD), 0xFFFFFAC0 (PIOE) Access: Read/Write 31 30 29 28 27 26 25 24 Delay7 Delay6 23 22 21 20 19 18 17 16 Delay5 Delay4 15 14 13 12 11 10 9 8 Delay3 Delay2 7 6 5 4 3 2 1 0 Delay1 Delay0 • Delay x: Gives the number of elements in the delay line associated to pad x. SAM9M11 [DATASHEET] 495 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.31PIO Write Protect Mode Register Name: PIO_WPMR Address: 0xFFFFF2E4 (PIOA), 0xFFFFF4E4 (PIOB), 0xFFFFF6E4 (PIOC), 0xFFFFF8E4 (PIOD), 0xFFFFFAE4 (PIOE) Access: Read/Write 31 30 29 28 27 26 25 24 WPKEY 23 22 21 20 19 18 17 16 WPKEY 15 14 13 12 11 10 9 8 WPKEY 7 6 5 4 3 2 1 0 — — — — — — — WPEN • WPEN: Write Protect Enable 0: Disables the Write Protect if WPKEY corresponds to 0x50494F (“PIO” in ASCII). 1: Enables the Write Protect if WPKEY corresponds to 0x50494F (“PIO” in ASCII). Protects the registers listed below: (cid:129) “PIO Enable Register” on page 466 (cid:129) “PIO Disable Register” on page 467 (cid:129) “PIO Output Enable Register” on page 469 (cid:129) “PIO Output Disable Register” on page 470 (cid:129) “PIO Input Filter Enable Register” on page 472 (cid:129) “PIO Input Filter Disable Register” on page 473 (cid:129) “PIO Set Output Data Register” on page 475 (cid:129) “PIO Clear Output Data Register” on page 476 (cid:129) “PIO Multi-driver Enable Register” on page 483 (cid:129) “PIO Multi-driver Disable Register” on page 484 (cid:129) “PIO Pull-up Disable Register” on page 486 (cid:129) “PIO Pull-up Enable Register” on page 487 (cid:129) “PIO Peripheral A Select Register” on page 489 (cid:129) “PIO Peripheral B Select Register” on page 490 (cid:129) “PIO Output Write Enable Register” on page 492 (cid:129) “PIO Output Write Disable Register” on page 493 • WPKEY: Write Protect Key Should be written at value 0x534D43 (“SMC” in ASCII). Writing any other value in this field aborts the write operation of the WPEN bit. Always reads as 0. 496 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

29.6.32PIO Write Protect Status Register Name: PIO_WPSR Address: 0xFFFFF2E8 (PIOA), 0xFFFFF4E8 (PIOB), 0xFFFFF6E8 (PIOC), 0xFFFFF8E8 (PIOD), 0xFFFFFAE8 (PIOE) Access: Read-only 31 30 29 28 27 26 25 24 — — — — — — — — 23 22 21 20 19 18 17 16 WPVSRC 15 14 13 12 11 10 9 8 WPVSRC 7 6 5 4 3 2 1 0 — — — — — — — WPVS • WPVS: Write Protect Enable 0: No Write Protect Violation has occurred since the last read of the PIO_WPSR. 1: A Write Protect Violation occurred since the last read of the PIO_WPSR. If this violation is an unauthorized attempt to write a protected register, the associated violation is reported into field WPVSRC. • WPVSRC: Write Protect Violation Source When WPVS is active, this field indicates the write-protected register (through address offset or code) in which a write access has been attempted. Note: Reading PIO_WPSR automatically clears all fields. SAM9M11 [DATASHEET] 497 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30. Universal Synchronous Asynchronous Receiver Transmitter (USART) 30.1 Description The Universal Synchronous Asynchronous Receiver Transmitter (USART) provides one full duplex universal synchronous asynchronous serial link. Data frame format is widely programmable (data length, parity, number of stop bits) to support a maximum of standards. The receiver implements parity error, framing error and overrun error detection. The receiver time-out enables handling variable-length frames and the transmitter timeguard facilitates communications with slow remote devices. Multidrop communications are also supported through address bit handling in reception and transmission. The USART features three test modes: remote loopback, local loopback and automatic echo. The USART supports specific operating modes providing interfaces on RS485, LIN and SPI buses, with ISO7816 T = 0 or T = 1 smart card slots and infrared transceivers. The hardware handshaking feature enables an out-of- band flow control by automatic management of the pins RTS and CTS. The USART supports the connection to the Peripheral DMA Controller, which enables data transfers to the transmitter and from the receiver. The PDC provides chained buffer management without any intervention of the processor. 30.2 Embedded Characteristics  Programmable Baud Rate Generator  5- to 9-bit full-duplex synchronous or asynchronous serial communications ̶ 1, 1.5 or 2 stop bits in Asynchronous Mode or 1 or 2 stop bits in Synchronous Mode ̶ Parity generation and error detection ̶ Framing error detection, overrun error detection ̶ MSB- or LSB-first ̶ Optional break generation and detection ̶ By 8 or by-16 over-sampling receiver frequency ̶ Hardware handshaking RTS-CTS ̶ Receiver time-out and transmitter timeguard ̶ Optional Multi-drop Mode with address generation and detection ̶ Optional Manchester Encoding  RS485 with driver control signal  ISO7816, T = 0 or T = 1 Protocols for interfacing with smart cards ̶ NACK handling, error counter with repetition and iteration limit  IrDA modulation and demodulation ̶ Communication at up to 115.2 Kbps  Test Modes ̶ Remote Loopback, Local Loopback, Automatic Echo 498 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.3 Block Diagram Figure 30-1. USART Block Diagram Peripheral DMA Controller Channel Channel PIO USART Controller RXD Receiver RTS AIC USART TXD Interrupt Transmitter CTS PMC MCK SCK Baud Rate Generator MCK/DIV DIV User Interface SLCK APB Table 30-1. SPI Operating Mode PIN USART SPI Slave SPI Master RXD RXD MOSI MISO TXD TXD MISO MOSI RTS RTS – CS CTS CTS CS – SAM9M11 [DATASHEET] 499 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.4 Application Block Diagram Figure 30-2. Application Block Diagram PPP IrLAP Field Bus EMV SPI Serial Driver Driver IrDA Driver Driver Driver USART RS232 RS485 Smart IrDA SPI Drivers Drivers Card Transceivers Bus Slot Serial Differential Port Bus 30.5 I/O Lines Description Table 30-2. I/O Line Description Name Description Type Active Level SCK Serial Clock I/O Transmit Serial Data TXD or Master Out Slave In (MOSI) in SPI Master Mode I/O or Master In Slave Out (MISO) in SPI Slave Mode Receive Serial Data RXD or Master In Slave Out (MISO) in SPI Master Mode Input or Master Out Slave In (MOSI) in SPI Slave Mode Clear to Send CTS Input Low or Slave Select (NSS) in SPI Slave Mode Request to Send RTS Output Low or Slave Select (NSS) in SPI Master Mode 500 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.6 Product Dependencies 30.6.1 I/O Lines The pins used for interfacing the USART may be multiplexed with the PIO lines. The programmer must first program the PIO controller to assign the desired USART pins to their peripheral function. If I/O lines of the USART are not used by the application, they can be used for other purposes by the PIO Controller. To prevent the TXD line from falling when the USART is disabled, the use of an internal pull-up is mandatory. If the hardware handshaking feature is used, the internal pull-up on TXD must also be enabled. Table 30-3. I/O Lines Instance Signal I/O Line Peripheral USART0 CTS0 PB15 B USART0 RTS0 PB17 B USART0 RXD0 PB18 A USART0 SCK0 PB16 B USART0 TXD0 PB19 A USART1 CTS1 PD17 A USART1 RTS1 PD16 A USART1 RXD1 PB5 A USART1 SCK1 PD29 B USART1 TXD1 PB4 A USART2 CTS2 PC11 B USART2 RTS2 PC9 B USART2 RXD2 PB7 A USART2 SCK2 PD30 B USART2 TXD2 PB6 A USART3 CTS3 PA24 B USART3 RTS3 PA23 B USART3 RXD3 PB9 A USART3 SCK3 PA22 B USART3 TXD3 PB8 A 30.6.2 Power Management The USART is not continuously clocked. The programmer must first enable the USART Clock in the Power Management Controller (PMC) before using the USART. However, if the application does not require USART operations, the USART clock can be stopped when not needed and be restarted later. In this case, the USART will resume its operations where it left off. Configuring the USART does not require the USART clock to be enabled. SAM9M11 [DATASHEET] 501 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.6.3 Interrupt The USART interrupt line is connected on one of the internal sources of the Advanced Inter-rupt Controller. Using the USART interrupt requires the AIC to be programmed first. Note that it is not recommended to use the USART interrupt line in edge sensitive mode. Table 30-4. Peripheral IDs Instance ID USART0 7 USART1 8 USART2 9 USART3 10 502 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.7 Functional Description The USART is capable of managing several types of serial synchronous or asynchronous communications. It supports the following communication modes:  5- to 9-bit full-duplex asynchronous serial communication ̶ MSB- or LSB-first ̶ 1, 1.5 or 2 stop bits ̶ Parity even, odd, marked, space or none ̶ By 8 or by 16 over-sampling receiver frequency ̶ Optional hardware handshaking ̶ Optional break management ̶ Optional multidrop serial communication  High-speed 5- to 9-bit full-duplex synchronous serial communication ̶ MSB- or LSB-first ̶ 1 or 2 stop bits ̶ Parity even, odd, marked, space or none ̶ By 8 or by 16 over-sampling frequency ̶ Optional hardware handshaking ̶ Optional break management ̶ Optional multidrop serial communication  RS485 with driver control signal  ISO7816, T0 or T1 protocols for interfacing with smart cards ̶ NACK handling, error counter with repetition and iteration limit  InfraRed IrDA Modulation and Demodulation  SPI Mode ̶ Master or Slave ̶ Serial Clock Programmable Phase and Polarity ̶ SPI Serial Clock (SCK) Frequency up to Internal Clock Frequency MCK/4  LIN Mode ̶ Compliant with LIN 1.3 and LIN 2.0 specifications ̶ Master or Slave ̶ Processing of frames with up to 256 data bytes ̶ Response Data length can be configurable or defined automatically by the Identifier ̶ Self synchronization in Slave node configuration ̶ Automatic processing and verification of the “Synch Break” and the “Synch Field” ̶ The “Synch Break” is detected even if it is partially superimposed with a data byte ̶ Automatic Identifier parity calculation/sending and verification ̶ Parity sending and verification can be disabled ̶ Automatic Checksum calculation/sending and verification ̶ Checksum sending and verification can be disabled ̶ Support both “Classic” and “Enhanced” checksum types ̶ Full LIN error checking and reporting ̶ Frame Slot Mode: the Master allocates slots to the scheduled frames automatically. ̶ Generation of the Wakeup signal  Test modes ̶ Remote loopback, local loopback, automatic echo SAM9M11 [DATASHEET] 503 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.7.1 Baud Rate Generator The Baud Rate Generator provides the bit period clock named the Baud Rate Clock to both the receiver and the transmitter. The Baud Rate Generator clock source can be selected by setting the USCLKS field in the Mode Register (US_MR) between:  the Master Clock MCK  a division of the Master Clock, the divider being product dependent, but generally set to 8  the external clock, available on the SCK pin The Baud Rate Generator is based upon a 16-bit divider, which is programmed with the CD field of the Baud Rate Generator Register (US_BRGR). If CD is programmed at 0, the Baud Rate Generator does not generate any clock. If CD is programmed at 1, the divider is bypassed and becomes inactive. If the external SCK clock is selected, the duration of the low and high levels of the signal provided on the SCK pin must be longer than a Master Clock (MCK) period. The frequency of the signal provided on SCK must be at least 4.5 times lower than MCK. Figure 30-3. Baud Rate Generator USCLKS CD MCK CD 0 SCK MCK/DIV 1 16-bit Counter Reserved SCK 2 FIDI >1 SYNC 3 OVER 1 0 0 0 Sampling 0 Divider Baud Rate 1 Clock 1 SYNC Sampling USCLKS = 3 Clock 30.7.1.1 Baud Rate in Asynchronous Mode If the USART is programmed to operate in asynchronous mode, the selected clock is first divided by CD, which is field programmed in the Baud Rate Generator Register (US_BRGR). The resulting clock is provided to the receiver as a sampling clock and then divided by 16 or 8, depending on the programming of the OVER bit in US_MR. If OVER is set to 1, the receiver sampling is 8 times higher than the Baud Rate Clock. If OVER is cleared, the sampling is performed at 16 times the Baud Rate Clock. The following formula performs the calculation of the baud rate. SelectedClock Baudrate = -------------------------------------------- (8(2–Over)CD) This gives a maximum baud rate of MCK divided by 8, assuming that MCK is the highest possible clock and that OVER is programmed at 1. 504 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Baud Rate Calculation Example Table 30-5 shows calculations of CD to obtain a baud rate at 38400 bauds for different source clock frequencies. This table also shows the actual resulting baud rate and the error. Table 30-5. Baud Rate Example (OVER = 0) Source Clock Expected Baud Rate Actual Baud Rate (MHz (bit/s) Calculation Result CD (bit/s) Error 3 686 400 38 400 6.00 6 38 400.00 0.00% 4 915 200 38 400 8.00 8 38 400.00 0.00% 5 000 000 38 400 8.14 8 39 062.50 1.70% 7 372 800 38 400 12.00 12 38 400.00 0.00% 8 000 000 38 400 13.02 13 38 461.54 0.16% 12 000 000 38 400 19.53 20 37 500.00 2.40% 12 288 000 38 400 20.00 20 38 400.00 0.00% 14 318 180 38 400 23.30 23 38 908.10 1.31% 14 745 600 38 400 24.00 24 38 400.00 0.00% 18 432 000 38 400 30.00 30 38 400.00 0.00% 24 000 000 38 400 39.06 39 38 461.54 0.16% 24 576 000 38 400 40.00 40 38 400.00 0.00% 25 000 000 38 400 40.69 40 38 109.76 0.76% 32 000 000 38 400 52.08 52 38 461.54 0.16% 32 768 000 38 400 53.33 53 38 641.51 0.63% 33 000 000 38 400 53.71 54 38 194.44 0.54% 40 000 000 38 400 65.10 65 38 461.54 0.16% 50 000 000 38 400 81.38 81 38 580.25 0.47% The baud rate is calculated with the following formula: BaudRate = MCK⁄CD×16 The baud rate error is calculated with the following formula. It is not recommended to work with an error higher than 5%. Error = 1–E-----x---p---e---c---t--e---d---B----a----u---d---R----a----t--e--  ActualBaudRate  SAM9M11 [DATASHEET] 505 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.7.1.2 Fractional Baud Rate in Asynchronous Mode The baud rate generator previously defined is subject to the following limitation: the output frequency changes by only integer multiples of the reference frequency. An approach to this problem is to integrate a fractional N clock generator that has a high resolution. The generator architecture is modified to obtain baud rate changes by a fraction of the reference source clock. This fractional part is programmed with the FP field in the Baud Rate Generator Register (US_BRGR). If FP is not 0, the fractional part is activated. The resolution is one eighth of the clock divider. This feature is only available when using USART normal mode. The fractional baud rate is calculated using the following formula: SelectedClock Baudrate = ---------------------------------------------------------------- 8(2–Over)CD+F----P---   8  The modified architecture is presented below: Figure 30-4. Fractional Baud Rate Generator FP USCLKS Modulus CD Control FP MCK CD 0 SCK MCK/DIV 1 16-bit Counter SCK Reserved 2 glitch-free FIDI logic >1 SYNC 3 OVER 1 0 0 0 Sampling 0 Divider Baud Rate 1 Clock 1 SYNC Sampling USCLKS = 3 Clock 30.7.1.3 Baud Rate in Synchronous Mode or SPI Mode If the USART is programmed to operate in synchronous mode, the selected clock is simply divided by the field CD in US_BRGR. SelectedClock BaudRate = -------------------------------------- CD In synchronous mode, if the external clock is selected (USCLKS = 3), the clock is provided directly by the signal on the USART SCK pin. No division is active. The value written in US_BRGR has no effect. The external clock frequency must be at least 4.5 times lower than the system clock. In synchronous mode master (USCLKS = 0 or 1, CLK0 set to 1), the receive part limits the SCK maximum frequency to MCK/4.5. When either the external clock SCK or the internal clock divided (MCK/DIV) is selected, the value programmed in CD must be even if the user has to ensure a 50:50 mark/space ratio on the SCK pin. If the internal clock MCK is selected, the Baud Rate Generator ensures a 50:50 duty cycle on the SCK pin, even if the value programmed in CD is odd. 506 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.7.1.4 Baud Rate in ISO 7816 Mode The ISO7816 specification defines the bit rate with the following formula: Di B = ------×f Fi where:  B is the bit rate  Di is the bit-rate adjustment factor  Fi is the clock frequency division factor  f is the ISO7816 clock frequency (Hz) Di is a binary value encoded on a 4-bit field, named DI, as represented in Table 30-6. Table 30-6. Binary and Decimal Values for Di DI field 0001 0010 0011 0100 0101 0110 1000 1001 Di (decimal) 1 2 4 8 16 32 12 20 Fi is a binary value encoded on a 4-bit field, named FI, as represented in Table 30-7. Table 30-7. Binary and Decimal Values for Fi FI field 0000 0001 0010 0011 0100 0101 0110 1001 1010 1011 1100 1101 Fi (decimal 372 372 558 744 1116 1488 1860 512 768 1024 1536 2048 Table 30-8 shows the resulting Fi/Di Ratio, which is the ratio between the ISO7816 clock and the Baud Rate Clock. Table 30-8. Possible Values for the Fi/Di Ratio Fi/Di 372 558 744 1116 1488 1806 512 768 1024 1536 2048 1 372 558 744 1116 1488 1860 512 768 1024 1536 2048 2 186 279 372 558 744 930 256 384 512 768 1024 4 93 139.5 186 279 372 465 128 192 256 384 512 8 46.5 69.75 93 139.5 186 232.5 64 96 128 192 256 16 23.25 34.87 46.5 69.75 93 116.2 32 48 64 96 128 32 11.62 17.43 23.25 34.87 46.5 58.13 16 24 32 48 64 12 31 46.5 62 93 124 155 42.66 64 85.33 128 170.6 20 18.6 27.9 37.2 55.8 74.4 93 25.6 38.4 51.2 76.8 102.4 If the USART is configured in ISO7816 Mode, the clock selected by the USCLKS field in the Mode Register (US_MR) is first divided by the value programmed in the field CD in the Baud Rate Generator Register (US_BRGR). The resulting clock can be provided to the SCK pin to feed the smart card clock inputs. This means that the CLKO bit can be set in US_MR. This clock is then divided by the value programmed in the FI_DI_RATIO field in the FI_DI_Ratio register (US_FIDI). This is performed by the Sampling Divider, which performs a division by up to 2047 in ISO7816 Mode. The non-integer values of the Fi/Di Ratio are not supported and the user must program the FI_DI_RATIO field to a value as close as possible to the expected value. The FI_DI_RATIO field resets to the value 0x174 (372 in decimal) and is the most common divider between the ISO7816 clock and the bit rate (Fi = 372, Di = 1). Figure 30-5 shows the relation between the Elementary Time Unit, corresponding to a bit time, and the ISO 7816 clock. SAM9M11 [DATASHEET] 507 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 30-5. Elementary Time Unit (ETU) FI_DI_RATIO ISO7816 Clock Cycles ISO7816 Clock on SCK ISO7816 I/O Line on TXD 1 ETU 30.7.2 Receiver and Transmitter Control After reset, the receiver is disabled. The user must enable the receiver by setting the RXEN bit in the Control Register (US_CR). However, the receiver registers can be programmed before the receiver clock is enabled. After reset, the transmitter is disabled. The user must enable it by setting the TXEN bit in the Control Register (US_CR). However, the transmitter registers can be programmed before being enabled. The Receiver and the Transmitter can be enabled together or independently. At any time, the software can perform a reset on the receiver or the transmitter of the USART by setting the corresponding bit, RSTRX and RSTTX respectively, in the Control Register (US_CR). The software resets clear the status flag and reset internal state machines but the user interface configuration registers hold the value configured prior to software reset. Regardless of what the receiver or the transmitter is performing, the communication is immediately stopped. The user can also independently disable the receiver or the transmitter by setting RXDIS and TXDIS respectively in US_CR. If the receiver is disabled during a character reception, the USART waits until the end of reception of the current character, then the reception is stopped. If the transmitter is disabled while it is operating, the USART waits the end of transmission of both the current character and character being stored in the Transmit Holding Register (US_THR). If a timeguard is programmed, it is handled normally. 30.7.3 Synchronous and Asynchronous Modes 30.7.3.1 Transmitter Operations The transmitter performs the same in both synchronous and asynchronous operating modes (SYNC = 0 or SYNC = 1). One start bit, up to 9 data bits, one optional parity bit and up to two stop bits are successively shifted out on the TXD pin at each falling edge of the programmed serial clock. The number of data bits is selected by the CHRL field and the MODE 9 bit in the Mode Register (US_MR). Nine bits are selected by setting the MODE 9 bit regardless of the CHRL field. The parity bit is set according to the PAR field in US_MR. The even, odd, space, marked or none parity bit can be configured. The MSBF field in US_MR configures which data bit is sent first. If written at 1, the most significant bit is sent first. At 0, the less significant bit is sent first. The number of stop bits is selected by the NBSTOP field in US_MR. The 1.5 stop bit is supported in asynchronous mode only. 508 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 30-6. Character Transmit Example: 8-bit, Parity Enabled One Stop Baud Rate Clock TXD Start D0 D1 D2 D3 D4 D5 D6 D7 Parity Stop Bit Bit Bit The characters are sent by writing in the Transmit Holding Register (US_THR). The transmitter reports two status bits in the Channel Status Register (US_CSR): TXRDY (Transmitter Ready), which indicates that US_THR is empty and TXEMPTY, which indicates that all the characters written in US_THR have been processed. When the current character processing is completed, the last character written in US_THR is transferred into the Shift Register of the transmitter and US_THR becomes empty, thus TXRDY rises. Both TXRDY and TXEMPTY bits are low when the transmitter is disabled. Writing a character in US_THR while TXRDY is low has no effect and the written character is lost. Figure 30-7. Transmitter Status Baud Rate Clock TXD Start ParityStopStart ParityStop D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 Bit Bit Bit Bit Bit Bit Write US_THR TXRDY TXEMPTY 30.7.3.2 Manchester Encoder When the Manchester encoder is in use, characters transmitted through the USART are encoded based on biphase Manchester II format. To enable this mode, set the MAN field in the US_MR to 1. Depending on polarity configuration, a logic level (zero or one), is transmitted as a coded signal one-to-zero or zero-to-one. Thus, a transition always occurs at the midpoint of each bit time. It consumes more bandwidth than the original NRZ signal (2x) but the receiver has more error control since the expected input must show a change at the center of a bit cell. An example of Manchester encoded sequence is: the byte 0xB1 or 10110001 encodes to 10 01 10 10 01 01 01 10, assuming the default polarity of the encoder. Figure 30-8 illustrates this coding scheme. Figure 30-8. NRZ to Manchester Encoding NRZ 1 0 1 1 0 0 0 1 encoded data Manchester encoded Txd data SAM9M11 [DATASHEET] 509 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The Manchester encoded character can also be encapsulated by adding both a configurable preamble and a start frame delimiter pattern. Depending on the configuration, the preamble is a training sequence, composed of a pre- defined pattern with a programmable length from 1 to 15 bit times. If the preamble length is set to 0, the preamble waveform is not generated prior to any character. The preamble pattern is chosen among the following sequences: ALL_ONE, ALL_ZERO, ONE_ZERO or ZERO_ONE, writing the field TX_PP in the US_MAN register, the field TX_PL is used to configure the preamble length. Figure 30-9 illustrates and defines the valid patterns. To improve flexibility, the encoding scheme can be configured using the TX_MPOL field in the US_MAN register. If the TX_MPOL field is set to zero (default), a logic zero is encoded with a zero-to-one transition and a logic one is encoded with a one-to-zero transition. If the TX_MPOL field is set to one, a logic one is encoded with a one-to-zero transition and a logic zero is encoded with a zero-to-one transition. Figure 30-9. Preamble Patterns, Default Polarity Assumed Manchester encoded SFD DATA Txd data 8 bit width "ALL_ONE" Preamble Manchester encoded SFD DATA Txd data 8 bit width "ALL_ZERO" Preamble Manchester encoded Txd SFD DATA data 8 bit width "ZERO_ONE" Preamble Manchester encoded SFD DATA Txd data 8 bit width "ONE_ZERO" Preamble A start frame delimiter is to be configured using the ONEBIT field in the US_MR. It consists of a user-defined pattern that indicates the beginning of a valid data. Figure 30-10 illustrates these patterns. If the start frame delimiter, also known as start bit, is one bit, (ONEBIT at 1), a logic zero is Manchester encoded and indicates that a new character is being sent serially on the line. If the start frame delimiter is a synchronization pattern also referred to as sync (ONEBIT at 0), a sequence of 3 bit times is sent serially on the line to indicate the start of a new character. The sync waveform is in itself an invalid Manchester waveform as the transition occurs at the middle of the second bit time. Two distinct sync patterns are used: the command sync and the data sync. The command sync has a logic one level for one and a half bit times, then a transition to logic zero for the second one and a half bit times. If the MODSYNC field in the US_MR is set to 1, the next character is a command. If it is set to 0, the next character is a data. When direct memory access is used, the MODSYNC field can be immediately updated with a modified character located in memory. To enable this mode, VAR_SYNC field in US_MR must be set to 1. In this case, the MODSYNC field in US_MR is bypassed and the sync configuration is held in the TXSYNH in the US_THR. The USART character format is modified and includes sync information. 510 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 30-10. Start Frame Delimiter Preamble Length is set to 0 SFD Manchester encoded DATA Txd data One bit start frame delimiter SFD Manchester encoded DATA Txd data Command Sync start frame delimiter SFD Manchester encoded DATA Txd data Data Sync start frame delimiter 30.7.3.3 Drift Compensation Drift compensation is available only in 16X oversampling mode. An hardware recovery system allows a larger clock drift. To enable the hardware system, the bit in the USART_MAN register must be set. If the RXD edge is one 16X clock cycle from the expected edge, this is considered as normal jitter and no corrective actions is taken. If the RXD event is between 4 and 2 clock cycles before the expected edge, then the current period is shortened by one clock cycle. If the RXD event is between 2 and 3 clock cycles after the expected edge, then the current period is lengthened by one clock cycle. These intervals are considered to be drift and so corrective actions are automatically taken. Figure 30-11. Bit Resynchronization Oversampling 16x Clock RXD Sampling point Expected edge Synchro. Tolerance Sync Synchro. Synchro. Jump Jump Error Error 30.7.3.4 Asynchronous Receiver If the USART is programmed in asynchronous operating mode (SYNC = 0), the receiver oversamples the RXD input line. The oversampling is either 16 or 8 times the Baud Rate clock, depending on the OVER bit in the Mode Register (US_MR). The receiver samples the RXD line. If the line is sampled during one half of a bit time at 0, a start bit is detected and data, parity and stop bits are successively sampled on the bit rate clock. If the oversampling is 16, (OVER at 0), a start is detected at the eighth sample at 0. Then, data bits, parity bit and stop bit are sampled on each 16 sampling clock cycle. If the oversampling is 8 (OVER at 1), a start bit is detected at the fourth sample at 0. Then, data bits, parity bit and stop bit are sampled on each 8 sampling clock cycle. SAM9M11 [DATASHEET] 511 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The number of data bits, first bit sent and parity mode are selected by the same fields and bits as the transmitter, i.e., respectively CHRL, MODE9, MSBF and PAR. For the synchronization mechanism only, the number of stop bits has no effect on the receiver as it considers only one stop bit, regardless of the field NBSTOP, so that resynchronization between the receiver and the transmitter can occur. Moreover, as soon as the stop bit is sampled, the receiver starts looking for a new start bit so that resynchronization can also be accomplished when the transmitter is operating with one stop bit. Figure 30-12 and Figure 30-13 illustrate start detection and character reception when USART operates in asynchronous mode. Figure 30-12. Asynchronous Start Detection Baud Rate Clock Sampling Clock (x16) RXD Sampling 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 D0 Start Sampling Detection RXD Sampling 1 2 3 4 5 6 7 0 1 2 3 4 Start Rejection Figure 30-13. Asynchronous Character Reception Example: 8-bit, Parity Enabled Baud Rate Clock RXD Start 16 16 16 16 16 16 16 16 16 16 Detection samplessamplessamplessamplessamplessamplessamplessamplessamplessamples D0 D1 D2 D3 D4 D5 D6 D7 Parity Stop Bit Bit 30.7.3.5 Manchester Decoder When the MAN field in US_MR is set to 1, the Manchester decoder is enabled. The decoder performs both preamble and start frame delimiter detection. One input line is dedicated to Manchester encoded input data. An optional preamble sequence can be defined, its length is user-defined and totally independent of the emitter side. Use RX_PL in US_MAN register to configure the length of the preamble sequence. If the length is set to 0, no preamble is detected and the function is disabled. In addition, the polarity of the input stream is programmable with RX_MPOL field in US_MAN register. Depending on the desired application the preamble pattern matching is to be defined via the RX_PP field in US_MAN. See Figure 30-9 for available preamble patterns. 512 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Unlike preamble, the start frame delimiter is shared between Manchester Encoder and Decoder. So, if ONEBIT field is set to 1, only a zero encoded Manchester can be detected as a valid start frame delimiter. If ONEBIT is set to 0, only a sync pattern is detected as a valid start frame delimiter. Decoder operates by detecting transition on incoming stream. If RXD is sampled during one quarter of a bit time at zero, a start bit is detected. See Figure 30- 14. The sample pulse rejection mechanism applies. Figure 30-14. Asynchronous Start Bit Detection Sampling Clock (16 x) Manchester encoded Txd data Start Detection 1 2 3 4 The receiver is activated and starts Preamble and Frame Delimiter detection, sampling the data at one quarter and then three quarters. If a valid preamble pattern or start frame delimiter is detected, the receiver continues decoding with the same synchronization. If the stream does not match a valid pattern or a valid start frame delimiter, the receiver re-synchronizes on the next valid edge.The minimum time threshold to estimate the bit value is three quarters of a bit time. If a valid preamble (if used) followed with a valid start frame delimiter is detected, the incoming stream is decoded into NRZ data and passed to USART for processing. Figure 30-15 illustrates Manchester pattern mismatch. When incoming data stream is passed to the USART, the receiver is also able to detect Manchester code violation. A code violation is a lack of transition in the middle of a bit cell. In this case, MANE flag in US_CSR is raised. It is cleared by writing the Control Register (US_CR) with the RSTSTA bit at 1. See Figure 30-16 for an example of Manchester error detection during data phase. Figure 30-15. Preamble Pattern Mismatch Preamble Mismatch Preamble Mismatch Manchester coding error invalid pattern Manchester encoded SFD DATA Txd data Preamble Length is set to 8 Figure 30-16. Manchester Error Flag Preamble Length is set to 4 Elementary character bit time SFD Manchester encoded Txd data Entering USART character area sampling points Preamble subpacket Manchester and Start Frame Delimiter Coding Error were successfully detected decoded SAM9M11 [DATASHEET] 513 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

When the start frame delimiter is a sync pattern (ONEBIT field at 0), both command and data delimiter are supported. If a valid sync is detected, the received character is written as RXCHR field in the US_RHR and the RXSYNH is updated. RXCHR is set to 1 when the received character is a command, and it is set to 0 if the received character is a data. This mechanism alleviates and simplifies the direct memory access as the character contains its own sync field in the same register. As the decoder is set up to be used in unipolar mode, the first bit of the frame has to be a zero-to-one transition. 30.7.3.6 Radio Interface: Manchester Encoded USART Application This section describes low data rate RF transmission systems and their integration with a Manchester encoded USART. These systems are based on transmitter and receiver ICs that support ASK and FSK modulation schemes. The goal is to perform full duplex radio transmission of characters using two different frequency carriers. See the configuration in Figure 30-17. Figure 30-17. Manchester Encoded Characters RF Transmission Fup frequency Carrier ASK/FSK Upstream Receiver Upstream Emitter LNA Serial VCO Configuration RF filter Interface Demod control Manchester USART Fdown frequency Carrier bi-dir decoder Receiver line ASK/FSK downstream transmitter Downstream Manchester USART encoder Emitter Receiver PA RF filter Mod VCO control The USART module is configured as a Manchester encoder/decoder. Looking at the downstream communication channel, Manchester encoded characters are serially sent to the RF emitter. This may also include a user defined preamble and a start frame delimiter. Mostly, preamble is used in the RF receiver to distinguish between a valid data from a transmitter and signals due to noise. The Manchester stream is then modulated. See Figure 30-18 for an example of ASK modulation scheme. When a logic one is sent to the ASK modulator, the power amplifier, referred to as PA, is enabled and transmits an RF signal at downstream frequency. When a logic zero is transmitted, the RF signal is turned off. If the FSK modulator is activated, two different frequencies are used to transmit data. When a logic 1 is sent, the modulator outputs an RF signal at frequency F0 and switches to F1 if the data sent is a 0. See Figure 30-19. From the receiver side, another carrier frequency is used. The RF receiver performs a bit check operation examining demodulated data stream. If a valid pattern is detected, the receiver switches to receiving mode. The demodulated stream is sent to the Manchester decoder. Because of bit checking inside RF IC, the data transferred to the microcontroller is reduced by a user-defined number of bits. The Manchester preamble length is to be defined in accordance with the RF IC configuration. 514 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 30-18. ASK Modulator Output 1 0 0 1 NRZ stream Manchester encoded data default polarity Txd unipolar output ASK Modulator Output Uptstream Frequency F0 Figure 30-19. FSK Modulator Output 1 0 0 1 NRZ stream Manchester encoded data Txd default polarity unipolar output FSK Modulator Output Uptstream Frequencies [F0, F0+offset] 30.7.3.7 Synchronous Receiver In synchronous mode (SYNC = 1), the receiver samples the RXD signal on each rising edge of the Baud Rate Clock. If a low level is detected, it is considered as a start. All data bits, the parity bit and the stop bits are sampled and the receiver waits for the next start bit. Synchronous mode operations provide a high speed transfer capability. Configuration fields and bits are the same as in asynchronous mode. Figure 30-20 illustrates a character reception in synchronous mode. Figure 30-20. Synchronous Mode Character Reception Example: 8-bit, Parity Enabled 1 Stop Baud Rate Clock RXD Sampling Start D0 D1 D2 D3 D4 D5 D6 D7 Stop Bit Parity Bit 30.7.3.8 Receiver Operations When a character reception is completed, it is transferred to the Receive Holding Register (US_RHR) and the RXRDY bit in the Status Register (US_CSR) rises. If a character is completed while the RXRDY is set, the OVRE (Overrun Error) bit is set. The last character is transferred into US_RHR and overwrites the previous one. The OVRE bit is cleared by writing the Control Register (US_CR) with the RSTSTA (Reset Status) bit at 1. SAM9M11 [DATASHEET] 515 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 30-21. Receiver Status Baud Rate Clock RXD Start ParityStopStart ParityStop D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 Bit Bit Bit Bit Bit Bit RSTSTA = 1 Write US_CR Read US_RHR RXRDY OVRE 30.7.3.9 Parity The USART supports five parity modes selected by programming the PAR field in the Mode Register (US_MR). The PAR field also enables the Multidrop mode, see “Multidrop Mode” on page 517. Even and odd parity bit generation and error detection are supported. If even parity is selected, the parity generator of the transmitter drives the parity bit at 0 if a number of 1s in the character data bit is even, and at 1 if the number of 1s is odd. Accordingly, the receiver parity checker counts the number of received 1s and reports a parity error if the sampled parity bit does not correspond. If odd parity is selected, the parity generator of the transmitter drives the parity bit at 1 if a number of 1s in the character data bit is even, and at 0 if the number of 1s is odd. Accordingly, the receiver parity checker counts the number of received 1s and reports a parity error if the sampled parity bit does not correspond. If the mark parity is used, the parity generator of the transmitter drives the parity bit at 1 for all characters. The receiver parity checker reports an error if the parity bit is sampled at 0. If the space parity is used, the parity generator of the transmitter drives the parity bit at 0 for all characters. The receiver parity checker reports an error if the parity bit is sampled at 1. If parity is disabled, the transmitter does not generate any parity bit and the receiver does not report any parity error. Table 30-9 shows an example of the parity bit for the character 0x41 (character ASCII “A”) depending on the configuration of the USART. Because there are two bits at 1, 1 bit is added when a parity is odd, or 0 is added when a parity is even. Table 30-9. Parity Bit Examples Character Hexadecimal Binary Parity Bit Parity Mode A 0x41 0100 0001 1 Odd A 0x41 0100 0001 0 Even A 0x41 0100 0001 1 Mark A 0x41 0100 0001 0 Space A 0x41 0100 0001 None None When the receiver detects a parity error, it sets the PARE (Parity Error) bit in the Channel Status Register (US_CSR). The PARE bit can be cleared by writing the Control Register (US_CR) with the RSTSTA bit at 1. Figure 30-22 illustrates the parity bit status setting and clearing. 516 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 30-22. Parity Error Baud Rate Clock RXD Start BadStop D0 D1 D2 D3 D4 D5 D6 D7 Bit Parity Bit Bit RSTSTA = 1 Write US_CR PARE RXRDY 30.7.3.10 Multidrop Mode If the PAR field in the Mode Register (US_MR) is programmed to the value 0x6 or 0x07, the USART runs in Multidrop Mode. This mode differentiates the data characters and the address characters. Data is transmitted with the parity bit at 0 and addresses are transmitted with the parity bit at 1. If the USART is configured in multidrop mode, the receiver sets the PARE parity error bit when the parity bit is high and the transmitter is able to send a character with the parity bit high when the Control Register is written with the SENDA bit at 1. To handle parity error, the PARE bit is cleared when the Control Register is written with the bit RSTSTA at 1. The transmitter sends an address byte (parity bit set) when SENDA is written to US_CR. In this case, the next byte written to US_THR is transmitted as an address. Any character written in US_THR without having written the command SENDA is transmitted normally with the parity at 0. SAM9M11 [DATASHEET] 517 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.7.3.11 Transmitter Timeguard The timeguard feature enables the USART interface with slow remote devices. The timeguard function enables the transmitter to insert an idle state on the TXD line between two characters. This idle state actually acts as a long stop bit. The duration of the idle state is programmed in the TG field of the Transmitter Timeguard Register (US_TTGR). When this field is programmed at zero no timeguard is generated. Otherwise, the transmitter holds a high level on TXD after each transmitted byte during the number of bit periods programmed in TG in addition to the number of stop bits. As illustrated in Figure 30-23, the behavior of TXRDY and TXEMPTY status bits is modified by the programming of a timeguard. TXRDY rises only when the start bit of the next character is sent, and thus remains at 0 during the timeguard transmission if a character has been written in US_THR. TXEMPTY remains low until the timeguard transmission is completed as the timeguard is part of the current character being transmitted. Figure 30-23. Timeguard Operations TG = 4 TG = 4 Baud Rate Clock TXD Start ParityStop Start ParityStop D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 Bit Bit Bit Bit Bit Bit Write US_THR TXRDY TXEMPTY Table 30-10 indicates the maximum length of a timeguard period that the transmitter can handle in relation to the function of the Baud Rate. Table 30-10. Maximum Timeguard Length Depending on Baud Rate Baud Rate (bit/s) Bit Time (µs) Timeguard (ms) 1 200 833 212.50 9 600 104 26.56 14400 69.4 17.71 19200 52.1 13.28 28800 34.7 8.85 33400 29.9 7.63 56000 17.9 4.55 57600 17.4 4.43 115200 8.7 2.21 518 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.7.3.12 Receiver Time-out The Receiver Time-out provides support in handling variable-length frames. This feature detects an idle condition on the RXD line. When a time-out is detected, the bit TIMEOUT in the Channel Status Register (US_CSR) rises and can generate an interrupt, thus indicating to the driver an end of frame. The time-out delay period (during which the receiver waits for a new character) is programmed in the TO field of the Receiver Time-out Register (US_RTOR). If the TO field is programmed at 0, the Receiver Time-out is disabled and no time-out is detected. The TIMEOUT bit in US_CSR remains at 0. Otherwise, the receiver loads a 16-bit counter with the value programmed in TO. This counter is decremented at each bit period and reloaded each time a new character is received. If the counter reaches 0, the TIMEOUT bit in the Status Register rises. Then, the user can either:  Stop the counter clock until a new character is received. This is performed by writing the Control Register (US_CR) with the STTTO (Start Time-out) bit at 1. In this case, the idle state on RXD before a new character is received will not provide a time-out. This prevents having to handle an interrupt before a character is received and allows waiting for the next idle state on RXD after a frame is received.  Obtain an interrupt while no character is received. This is performed by writing US_CR with the RETTO (Reload and Start Time-out) bit at 1. If RETTO is performed, the counter starts counting down immediately from the value TO. This enables generation of a periodic interrupt so that a user time-out can be handled, for example when no key is pressed on a keyboard. If STTTO is performed, the counter clock is stopped until a first character is received. The idle state on RXD before the start of the frame does not provide a time-out. This prevents having to obtain a periodic interrupt and enables a wait of the end of frame when the idle state on RXD is detected. If RETTO is performed, the counter starts counting down immediately from the value TO. This enables generation of a periodic interrupt so that a user time-out can be handled, for example when no key is pressed on a keyboard. Figure 30-24 shows the block diagram of the Receiver Time-out feature. Figure 30-24. Receiver Time-out Block Diagram Baud Rate TO Clock 16-bit Value 1 D Q Clock 16-bit Time-out Counter = TIMEOUT STTTO Load 0 Clear Character Received RETTO SAM9M11 [DATASHEET] 519 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 30-11 gives the maximum time-out period for some standard baud rates. Table 30-11. Maximum Time-out Period Baud Rate (bit/s) Bit Time (µs) Time-out (ms) 600 1 667 109 225 1 200 833 54 613 2 400 417 27 306 4 800 208 13 653 9 600 104 6 827 14400 69 4 551 19200 52 3 413 28800 35 2 276 33400 30 1 962 56000 18 1 170 57600 17 1 138 200000 5 328 30.7.3.13 Framing Error The receiver is capable of detecting framing errors. A framing error happens when the stop bit of a received character is detected at level 0. This can occur if the receiver and the transmitter are fully desynchronized. A framing error is reported on the FRAME bit of the Channel Status Register (US_CSR). The FRAME bit is asserted in the middle of the stop bit as soon as the framing error is detected. It is cleared by writing the Control Register (US_CR) with the RSTSTA bit at 1. Figure 30-25. Framing Error Status Baud Rate Clock RXD Start ParityStop D0 D1 D2 D3 D4 D5 D6 D7 Bit Bit Bit RSTSTA = 1 Write US_CR FRAME RXRDY 30.7.3.14 Transmit Break The user can request the transmitter to generate a break condition on the TXD line. A break condition drives the TXD line low during at least one complete character. It appears the same as a 0x00 character sent with the parity and the stop bits at 0. However, the transmitter holds the TXD line at least during one character until the user requests the break condition to be removed. A break is transmitted by writing the Control Register (US_CR) with the STTBRK bit at 1. This can be performed at any time, either while the transmitter is empty (no character in either the Shift Register or in US_THR) or when a 520 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

character is being transmitted. If a break is requested while a character is being shifted out, the character is first completed before the TXD line is held low. Once STTBRK command is requested further STTBRK commands are ignored until the end of the break is completed. The break condition is removed by writing US_CR with the STPBRK bit at 1. If the STPBRK is requested before the end of the minimum break duration (one character, including start, data, parity and stop bits), the transmitter ensures that the break condition completes. The transmitter considers the break as though it is a character, i.e., the STTBRK and STPBRK commands are taken into account only if the TXRDY bit in US_CSR is at 1 and the start of the break condition clears the TXRDY and TXEMPTY bits as if a character is processed. Writing US_CR with the both STTBRK and STPBRK bits at 1 can lead to an unpredictable result. All STPBRK commands requested without a previous STTBRK command are ignored. A byte written into the Transmit Holding Register while a break is pending, but not started, is ignored. After the break condition, the transmitter returns the TXD line to 1 for a minimum of 12 bit times. Thus, the transmitter ensures that the remote receiver detects correctly the end of break and the start of the next character. If the timeguard is programmed with a value higher than 12, the TXD line is held high for the timeguard period. After holding the TXD line for this period, the transmitter resumes normal operations. Figure 30-26 illustrates the effect of both the Start Break (STTBRK) and Stop Break (STPBRK) commands on the TXD line. Figure 30-26. Break Transmission Baud Rate Clock TXD Start D0 D1 D2 D3 D4 D5 D6 D7ParityStop Break Transmission End of Break Bit Bit Bit STTBRK = 1 STPBRK = 1 Write US_CR TXRDY TXEMPTY 30.7.3.15 Receive Break The receiver detects a break condition when all data, parity and stop bits are low. This corresponds to detecting a framing error with data at 0x00, but FRAME remains low. When the low stop bit is detected, the receiver asserts the RXBRK bit in US_CSR. This bit may be cleared by writing the Control Register (US_CR) with the bit RSTSTA at 1. An end of receive break is detected by a high level for at least 2/16 of a bit period in asynchronous operating mode or one sample at high level in synchronous operating mode. The end of break detection also asserts the RXBRK bit. SAM9M11 [DATASHEET] 521 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.7.3.16 Hardware Handshaking The USART features a hardware handshaking out-of-band flow control. The RTS and CTS pins are used to connect with the remote device, as shown in Figure 30-27. Figure 30-27. Connection with a Remote Device for Hardware Handshaking USART Remote Device TXD RXD RXD TXD CTS RTS RTS CTS Setting the USART to operate with hardware handshaking is performed by writing the USART_MODE field in the Mode Register (US_MR) to the value 0x2. The USART behavior when hardware handshaking is enabled is the same as the behavior in standard synchronous or asynchronous mode, except that the receiver drives the RTS pin as described below and the level on the CTS pin modifies the behavior of the transmitter as described below. Using this mode requires using the PDC channel for reception. The transmitter can handle hardware handshaking in any case. Figure 30-28 shows how the receiver operates if hardware handshaking is enabled. The RTS pin is driven high if the receiver is disabled and if the status RXBUFF (Receive Buffer Full) coming from the PDC channel is high. Normally, the remote device does not start transmitting while its CTS pin (driven by RTS) is high. As soon as the Receiver is enabled, the RTS falls, indicating to the remote device that it can start transmitting. Defining a new buffer to the PDC clears the status bit RXBUFF and, as a result, asserts the pin RTS low. Figure 30-28. Receiver Behavior when Operating with Hardware Handshaking RXD RXEN = 1 RXDIS = 1 Write US_CR RTS RXBUFF Figure 30-29 shows how the transmitter operates if hardware handshaking is enabled. The CTS pin disables the transmitter. If a character is being processing, the transmitter is disabled only after the completion of the current character and transmission of the next character happens as soon as the pin CTS falls. Figure 30-29. Transmitter Behavior when Operating with Hardware Handshaking CTS TXD 522 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.7.4 ISO7816 Mode The USART features an ISO7816-compatible operating mode. This mode permits interfacing with smart cards and Security Access Modules (SAM) communicating through an ISO7816 link. Both T = 0 and T = 1 protocols defined by the ISO7816 specification are supported. Setting the USART in ISO7816 mode is performed by writing the USART_MODE field in the Mode Register (US_MR) to the value 0x4 for protocol T = 0 and to the value 0x5 for protocol T = 1. 30.7.4.1 ISO7816 Mode Overview The ISO7816 is a half duplex communication on only one bidirectional line. The baud rate is determined by a division of the clock provided to the remote device (see “Baud Rate Generator” on page 504). The USART connects to a smart card as shown in Figure 30-30. The TXD line becomes bidirectional and the Baud Rate Generator feeds the ISO7816 clock on the SCK pin. As the TXD pin becomes bidirectional, its output remains driven by the output of the transmitter but only when the transmitter is active while its input is directed to the input of the receiver. The USART is considered as the master of the communication as it generates the clock. Figure 30-30. Connection of a Smart Card to the USART USART CLK SCK Smart Card I/O TXD When operating in ISO7816, either in T = 0 or T = 1 modes, the character format is fixed. The configuration is 8 data bits, even parity and 1 or 2 stop bits, regardless of the values programmed in the CHRL, MODE9, PAR and CHMODE fields. MSBF can be used to transmit LSB or MSB first. Parity Bit (PAR) can be used to transmit in normal or inverse mode. Refer to “USART Mode Register” on page 551 and “PAR: Parity Type” on page 552. The USART cannot operate concurrently in both receiver and transmitter modes as the communication is unidirectional at a time. It has to be configured according to the required mode by enabling or disabling either the receiver or the transmitter as desired. Enabling both the receiver and the transmitter at the same time in ISO7816 mode may lead to unpredictable results. The ISO7816 specification defines an inverse transmission format. Data bits of the character must be transmitted on the I/O line at their negative value. The USART does not support this format and the user has to perform an exclusive OR on the data before writing it in the Transmit Holding Register (US_THR) or after reading it in the Receive Holding Register (US_RHR). 30.7.4.2 Protocol T = 0 In T = 0 protocol, a character is made up of one start bit, eight data bits, one parity bit and one guard time, which lasts two bit times. The transmitter shifts out the bits and does not drive the I/O line during the guard time. If no parity error is detected, the I/O line remains at 1 during the guard time and the transmitter can continue with the transmission of the next character, as shown in Figure 30-31. If a parity error is detected by the receiver, it drives the I/O line at 0 during the guard time, as shown in Figure 30- 32. This error bit is also named NACK, for Non Acknowledge. In this case, the character lasts 1 bit time more, as the guard time length is the same and is added to the error bit time which lasts 1 bit time. When the USART is the receiver and it detects an error, it does not load the erroneous character in the Receive Holding Register (US_RHR). It appropriately sets the PARE bit in the Status Register (US_SR) so that the software can handle the error. SAM9M11 [DATASHEET] 523 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 30-31. T = 0 Protocol without Parity Error Baud Rate Clock RXD Start D0 D1 D2 D3 D4 D5 D6 D7 Parity Guard Guard Next Bit Bit Time 1 Time 2 Start Bit Figure 30-32. T = 0 Protocol with Parity Error Baud Rate Clock I/O Error Start D0 D1 D2 D3 D4 D5 D6 D7 Parity Guard Guard Start D0 D1 Bit Bit Time 1 Time 2 Bit Repetition Receive Error Counter The USART receiver also records the total number of errors. This can be read in the Number of Error (US_NER) register. The NB_ERRORS field can record up to 255 errors. Reading US_NER automatically clears the NB_ERRORS field. Receive NACK Inhibit The USART can also be configured to inhibit an error. This can be achieved by setting the INACK bit in the Mode Register (US_MR). If INACK is at 1, no error signal is driven on the I/O line even if a parity bit is detected, but the INACK bit is set in the Status Register (US_SR). The INACK bit can be cleared by writing the Control Register (US_CR) with the RSTNACK bit at 1. Moreover, if INACK is set, the erroneous received character is stored in the Receive Holding Register, as if no error occurred. However, the RXRDY bit does not raise. Transmit Character Repetition When the USART is transmitting a character and gets a NACK, it can automatically repeat the character before moving on to the next one. Repetition is enabled by writing the MAX_ITERATION field in the Mode Register (US_MR) at a value higher than 0. Each character can be transmitted up to eight times; the first transmission plus seven repetitions. If MAX_ITERATION does not equal zero, the USART repeats the character as many times as the value loaded in MAX_ITERATION. When the USART repetition number reaches MAX_ITERATION, the ITERATION bit is set in the Channel Status Register (US_CSR). If the repetition of the character is acknowledged by the receiver, the repetitions are stopped and the iteration counter is cleared. The ITERATION bit in US_CSR can be cleared by writing the Control Register with the RSIT bit at 1. Disable Successive Receive NACK The receiver can limit the number of successive NACKs sent back to the remote transmitter. This is programmed by setting the bit DSNACK in the Mode Register (US_MR). The maximum number of NACK transmitted is programmed in the MAX_ITERATION field. As soon as MAX_ITERATION is reached, the character is considered as correct, an acknowledge is sent on the line and the ITERATION bit in the Channel Status Register is set. 524 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.7.4.3 Protocol T = 1 When operating in ISO7816 protocol T = 1, the transmission is similar to an asynchronous format with only one stop bit. The parity is generated when transmitting and checked when receiving. Parity error detection sets the PARE bit in the Channel Status Register (US_CSR). 30.7.5 IrDA Mode The USART features an IrDA mode supplying half-duplex point-to-point wireless communication. It embeds the modulator and demodulator which allows a glueless connection to the infrared transceivers, as shown in Figure 30-33. The modulator and demodulator are compliant with the IrDA specification version 1.1 and support data transfer speeds ranging from 2.4 kbit/s to 115.2 kbit/s. The USART IrDA mode is enabled by setting the USART_MODE field in the Mode Register (US_MR) to the value 0x8. The IrDA Filter Register (US_IF) allows configuring the demodulator filter. The USART transmitter and receiver operate in a normal asynchronous mode and all parameters are accessible. Note that the modulator and the demodulator are activated. Figure 30-33. Connection to IrDA Transceivers USART IrDA Transceivers Receiver Demodulator RXD RX TX Transmitter Modulator TXD The receiver and the transmitter must be enabled or disabled according to the direction of the transmission to be managed. To receive IrDA signals, the following needs to be done:  Disable TX and Enable RX  Configure the TXD pin as PIO and set it as an output at 0 (to avoid LED emission). Disable the internal pull- up (better for power consumption).  Receive data 30.7.5.1 IrDA Modulation For baud rates up to and including 115.2 kbit/s, the RZI modulation scheme is used. “0” is represented by a light pulse of 3/16th of a bit time. Some examples of signal pulse duration are shown in Table 30-12. Table 30-12. IrDA Pulse Duration Baud Rate Pulse Duration (3/16) 2.4 kbit/s 78.13 µs 9.6 kbit/s 19.53 µs 19.2 kbit/s 9.77 µs 38.4 kbit/s 4.88 µs 57.6 kbit/s 3.26 µs 115.2 kbit/s 1.63 µs SAM9M11 [DATASHEET] 525 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 30-34 shows an example of character transmission. Figure 30-34. IrDA Modulation Start Data Bits Stop Bit Bit Transmitter 0 1 0 1 0 0 1 1 0 1 Output TXD 3 Bit Period Bit Period 16 30.7.5.2 IrDA Baud Rate Table 30-13 gives some examples of CD values, baud rate error and pulse duration. Note that the requirement on the maximum acceptable error of ±1.87% must be met. Table 30-13. IrDA Baud Rate Error Peripheral Clock Baud Rate (bit/s) CD Baud Rate Error Pulse Time (µs) 3 686 400 115 200 2 0.00% 1.63 20 000 000 115 200 11 1.38% 1.63 32 768 000 115 200 18 1.25% 1.63 40 000 000 115 200 22 1.38% 1.63 3 686 400 57 600 4 0.00% 3.26 20 000 000 57 600 22 1.38% 3.26 32 768 000 57 600 36 1.25% 3.26 40 000 000 57 600 43 0.93% 3.26 3 686 400 38 400 6 0.00% 4.88 20 000 000 38 400 33 1.38% 4.88 32 768 000 38 400 53 0.63% 4.88 40 000 000 38 400 65 0.16% 4.88 3 686 400 19 200 12 0.00% 9.77 20 000 000 19 200 65 0.16% 9.77 32 768 000 19 200 107 0.31% 9.77 40 000 000 19 200 130 0.16% 9.77 3 686 400 9 600 24 0.00% 19.53 20 000 000 9 600 130 0.16% 19.53 32 768 000 9 600 213 0.16% 19.53 40 000 000 9 600 260 0.16% 19.53 3 686 400 2 400 96 0.00% 78.13 20 000 000 2 400 521 0.03% 78.13 32 768 000 2 400 853 0.04% 78.13 526 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.7.5.3 IrDA Demodulator The demodulator is based on the IrDA Receive filter comprised of an 8-bit down counter which is loaded with the value programmed in US_IF. When a falling edge is detected on the RXD pin, the Filter Counter starts counting down at the Master Clock (MCK) speed. If a rising edge is detected on the RXD pin, the counter stops and is reloaded with US_IF. If no rising edge is detected when the counter reaches 0, the input of the receiver is driven low during one bit time. Figure 30-35 illustrates the operations of the IrDA demodulator. Figure 30-35. IrDA Demodulator Operations MCK RXD Counter Value 6 5 4 3 2 6 6 5 4 3 2 1 0 Pulse Pulse Rejected Accepted Receiver Input As the IrDA mode uses the same logic as the ISO7816, note that the FI_DI_RATIO field in US_FIDI must be set to a value higher than 0 in order to assure IrDA communications operate correctly. 30.7.6 RS485 Mode The USART features the RS485 mode to enable line driver control. While operating in RS485 mode, the USART behaves as though in asynchronous or synchronous mode and configuration of all the parameters is possible. The difference is that the RTS pin is driven high when the transmitter is operating. The behavior of the RTS pin is controlled by the TXEMPTY bit. A typical connection of the USART to a RS485 bus is shown in Figure 30-36. Figure 30-36. Typical Connection to a RS485 Bus USART RXD Differential TXD Bus RTS The USART is set in RS485 mode by programming the USART_MODE field in the Mode Register (US_MR) to the value 0x1. The RTS pin is at a level inverse to the TXEMPTY bit. Significantly, the RTS pin remains high when a timeguard is programmed so that the line can remain driven after the last character completion. Figure 30-37 gives an example of the RTS waveform during a character transmission when the timeguard is enabled. SAM9M11 [DATASHEET] 527 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 30-37. Example of RTS Drive with Timeguard TG = 4 Baud Rate Clock TXD Start ParityStop D0 D1 D2 D3 D4 D5 D6 D7 Bit Bit Bit Write US_THR TXRDY TXEMPTY RTS 30.7.7 SPI Mode The Serial Peripheral Interface (SPI) Mode is a synchronous serial data link that provides communication with external devices in Master or Slave Mode. It also enables communication between processors if an external processor is connected to the system. The Serial Peripheral Interface is essentially a shift register that serially transmits data bits to other SPIs. During a data transfer, one SPI system acts as the “master” which controls the data flow, while the other devices act as “slaves'' which have data shifted into and out by the master. Different CPUs can take turns being masters and one master may simultaneously shift data into multiple slaves. (Multiple Master Protocol is the opposite of Single Master Protocol, where one CPU is always the master while all of the others are always slaves.) However, only one slave may drive its output to write data back to the master at any given time. A slave device is selected when its NSS signal is asserted by the master. The USART in SPI Master mode can address only one SPI Slave because it can generate only one NSS signal. The SPI system consists of two data lines and two control lines:  Master Out Slave In (MOSI): This data line supplies the output data from the master shifted into the input of the slave.  Master In Slave Out (MISO): This data line supplies the output data from a slave to the input of the master.  Serial Clock (SCK): This control line is driven by the master and regulates the flow of the data bits. The master may transmit data at a variety of baud rates. The SCK line cycles once for each bit that is transmitted.  Slave Select (NSS): This control line allows the master to select or deselect the slave. 30.7.7.1 Modes of Operation The USART can operate in SPI Master Mode or in SPI Slave Mode. Operation in SPI Master Mode is programmed by writing at 0xE the USART_MODE field in the Mode Register. In this case the SPI lines must be connected as described below:  The MOSI line is driven by the output pin TXD  The MISO line drives the input pin RXD  The SCK line is driven by the output pin SCK  The NSS line is driven by the output pin RTS 528 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Operation in SPI Slave Mode is programmed by writing at 0xF the USART_MODE field in the Mode Register. In this case the SPI lines must be connected as described below:  The MOSI line drives the input pin RXD  The MISO line is driven by the output pin TXD  The SCK line drives the input pin SCK  The NSS line drives the input pin CTS In order to avoid unpredicted behavior, any change of the SPI Mode must be followed by a software reset of the transmitter and of the receiver (except the initial configuration after a hardware reset). (See Section 30.7.8.2). 30.7.7.2 Baud Rate In SPI Mode, the baudrate generator operates in the same way as in USART synchronous mode: See “Baud Rate in Synchronous Mode or SPI Mode” on page 506. However, there are some restrictions: In SPI Master Mode:  The external clock SCK must not be selected (USCLKS ≠ 0x3), and the bit CLKO must be set to “1” in the Mode Register (US_MR), in order to generate correctly the serial clock on the SCK pin.  To obtain correct behavior of the receiver and the transmitter, the value programmed in CD of must be superior or equal to 6.  If the internal clock divided (MCK/DIV) is selected, the value programmed in CD must be even to ensure a 50:50 mark/space ratio on the SCK pin, this value can be odd if the internal clock is selected (MCK). In SPI Slave Mode:  The external clock (SCK) selection is forced regardless of the value of the USCLKS field in the Mode Register (US_MR). Likewise, the value written in US_BRGR has no effect, because the clock is provided directly by the signal on the USART SCK pin.  To obtain correct behavior of the receiver and the transmitter, the external clock (SCK) frequency must be at least 4 times lower than the system clock. 30.7.7.3 Data Transfer Up to 9 data bits are successively shifted out on the TXD pin at each rising or falling edge (depending of CPOL and CPHA) of the programmed serial clock. There is no Start bit, no Parity bit and no Stop bit. The number of data bits is selected by the CHRL field and the MODE 9 bit in the Mode Register (US_MR). The 9 bits are selected by setting the MODE 9 bit regardless of the CHRL field. The MSB data bit is always sent first in SPI Mode (Master or Slave). Four combinations of polarity and phase are available for data transfers. The clock polarity is programmed with the CPOL bit in the Mode Register. The clock phase is programmed with the CPHA bit. These two parameters determine the edges of the clock signal upon which data is driven and sampled. Each of the two parameters has two possible states, resulting in four possible combinations that are incompatible with one another. Thus, a master/slave pair must use the same parameter pair values to communicate. If multiple slaves are used and fixed in different configurations, the master must reconfigure itself each time it needs to communicate with a different slave. Table 30-14. SPI Bus Protocol Mode SPI Bus Protocol Mode CPOL CPHA 0 0 1 1 0 0 2 1 1 3 1 0 SAM9M11 [DATASHEET] 529 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 30-38. SPI Transfer Format (CPHA = 1, 8 bits per transfer) SCK cycle (for reference) 1 2 3 4 5 66 7 8 SCK (CPOL = 0) SCK (CPOL = 1) MOSI SPI Master ->TXD MSB 6 5 4 3 2 1 LSB SPI Slave -> RXD MISO SPI Master ->RXD MSB 6 5 4 3 2 1 LSB SPI Slave -> TXD NSS SPI Master -> RTS SPI Slave -> CTS Figure 30-39. SPI Transfer Format (CPHA = 0, 8 bits per transfer) SCK cycle (for reference) 1 2 3 4 5 6 7 8 SCK (CPOL = 0) SCK (CPOL = 1) MOSI SPI Master -> TXD MSB 6 5 4 3 2 1 LSB SPI Slave -> RXD MISO SPI Master -> RXD MSB 6 5 4 3 2 1 LSB SPI Slave -> TXD NSS SPI Master -> RTS SPI Slave -> CTS 30.7.7.4 Receiver and Transmitter Control See “Receiver and Transmitter Control” on page 508. 30.7.7.5 Character Transmission The characters are sent by writing in the Transmit Holding Register (US_THR). The transmitter reports two status bits in the Channel Status Register (US_CSR): TXRDY (Transmitter Ready), which indicates that US_THR is empty and TXEMPTY, which indicates that all the characters written in US_THR have been processed. When the 530 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

current character processing is completed, the last character written in US_THR is transferred into the Shift Register of the transmitter and US_THR becomes empty, thus TXRDY rises. Both TXRDY and TXEMPTY bits are low when the transmitter is disabled. Writing a character in US_THR while TXRDY is low has no effect and the written character is lost. If the USART is in SPI Slave Mode and if a character must be sent while the Transmit Holding Register (US_THR) is empty, the UNRE (Underrun Error) bit is set. The TXD transmission line stays at high level during all this time. The UNRE bit is cleared by writing the Control Register (US_CR) with the RSTSTA (Reset Status) bit at 1. In SPI Master Mode, the slave select line (NSS) is asserted at low level one t (t being the nominal time required bit bit to transmit a bit) before the transmission of the MSB bit and released at high level one t after the transmission of bit the LSB bit. So, the slave select line (NSS) is always released between each character transmission and a minimum delay of three t always inserted. However, in order to address slave devices supporting the CSAAT bit mode (Chip Select Active After Transfer), the slave select line (NSS) can be forced at low level by writing the Control Register (US_CR) with the RTSEN bit at 1. The slave select line (NSS) can be released at high level only by writing the Control Register (US_CR) with the RTSDIS bit at 1 (for example, when all data have been transferred to the slave device). In SPI Slave Mode, the transmitter does not require a falling edge of the slave select line (NSS) to initiate a character transmission but only a low level. However, this low level must be present on the slave select line (NSS) at least one t before the first serial clock cycle corresponding to the MSB bit. bit 30.7.7.6 Character Reception When a character reception is completed, it is transferred to the Receive Holding Register (US_RHR) and the RXRDY bit in the Status Register (US_CSR) rises. If a character is completed while RXRDY is set, the OVRE (Overrun Error) bit is set. The last character is transferred into US_RHR and overwrites the previous one. The OVRE bit is cleared by writing the Control Register (US_CR) with the RSTSTA (Reset Status) bit at 1. To ensure correct behavior of the receiver in SPI Slave Mode, the master device sending the frame must ensure a minimum delay of one t between each character transmission. The receiver does not require a falling edge of the bit slave select line (NSS) to initiate a character reception but only a low level. However, this low level must be present on the slave select line (NSS) at least one t before the first serial clock cycle corresponding to the MSB bit bit. 30.7.7.7 Receiver Timeout Because the receiver baud rate clock is active only during data transfers in SPI Mode, a receiver timeout is impossible in this mode, whatever the Time-out value is (field TO) in the Time-out Register (US_RTOR). 30.7.8 LIN Mode The LIN Mode provides Master node and Slave node connectivity on a LIN bus. The LIN (Local Interconnect Network) is a serial communication protocol which efficiently supports the control of mechatronic nodes in distributed automotive applications. The main properties of the LIN bus are:  Single Master/Multiple Slaves concept  Low cost silicon implementation based on common UART/SCI interface hardware, an equivalent in software, or as a pure state machine.  Self synchronization without quartz or ceramic resonator in the slave nodes  Deterministic signal transmission  Low cost single-wire implementation  Speed up to 20 kbit/s LIN provides cost efficient bus communication where the bandwidth and versatility of CAN are not required. SAM9M11 [DATASHEET] 531 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The LIN Mode enables processing LIN frames with a minimum of action from the microprocessor. 30.7.8.1 Modes of operation The USART can act either as a LIN Master node or as a LIN Slave node. The node configuration is chosen by setting the USART_MODE field in the USART3 Mode register (US_MR):  LIN Master Node (USART_MODE = 0xA)  LIN Slave Node (USART_MODE = 0xB) In order to avoid unpredicted behavior, any change of the LIN node configuration must be followed by a software reset of the transmitter and of the receiver (except the initial node configuration after a hardware reset). (See Section 30.7.8.2) 30.7.8.2 Receiver and Transmitter Control See “Receiver and Transmitter Control” on page 508. 30.7.8.3 Character Transmission See “Transmitter Operations” on page 508. 30.7.8.4 Character Reception See “Receiver Operations” on page 515. 30.7.8.5 Header Transmission (Master Node Configuration) All the LIN Frames start with a header which is sent by the master node and consists of a Synch Break Field, Synch Field and Identifier Field. So in Master node configuration, the frame handling starts with the sending of the header. The header is transmitted as soon as the identifier is written in the LIN Identifier register (US_LINIR). At this moment the flag TXRDY falls. The Break Field, the Synch Field and the Identifier Field are sent automatically one after the other. The Break Field consists of 13 dominant bits and 1 recessive bit, the Synch Field is the character 0x55 and the Identifier corresponds to the character written in the LIN Identifier Register (US_LINIR). The Identifier parity bits can be automatically computed and sent (see Section 30.7.8.8). The flag TXRDY rises when the identifier character is transferred into the Shift Register of the transmitter.As soon as the Synch Break Field is transmitted, the flag LINBK in the Channel Status register (US_CSR) is set to “1”. Likewise, as soon as the Identifier Field is sent, the flag LINID in the Channel Status register (US_CSR) is set to “1”. These flags are reset by writing the bit RSTSTA at “1” in the Control register (US_CR). Figure 30-40. Header Transmission Baud Rate Clock TXD 13 doBmrienaakn tF bieitlsd (at 0) 1 reDcBeelrisemsaiitkveer bit SBtairtt 1 0 Sy1nch B0yte =1 0x550 1 0 SBtoitpSBtaitrt ID0 ID1 ID2 ID3 ID4 ID5 ID6 ID7 SBtoitp Write (at 1) US_LINIR US_LINIR ID TXRDY LINBK in US_CSR LINID in US_CSR Write RSTSTA=1 in US_CR 532 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.7.8.6 Header Reception (Slave Node Configuration) All the LIN Frames start with a header which is sent by the master node and consists of a Synch Break Field, Synch Field and Identifier Field. In Slave node configuration, the frame handling starts with the reception of the header. The USART uses a break detection threshold of 11 nominal bit times at the actual baud rate. At any time, if 11 consecutive recessive bits are detected on the bus, the USART detects a Break Field. As long as a Break Field has not been detected, the USART stays idle and the received data are not taken in account. When a Break Field has been detected, the flag LINBK in the Channel Status register (US_CSR) is set to “1” and the USART expects the Synch Field character to be 0x55. This field is used to update the actual baud rate in order to stay synchronized (see Section 30.7.8.7). If the received Synch character is not 0x55, an Inconsistent Synch Field error is generated (see Section 30.7.8.13). After receiving the Synch Field, the USART expects to receive the Identifier Field. When the Identifier Field has been received, the flag LINID in the Channel Status register (US_CSR) is set to “1”. At this moment the field IDCHR in the LIN Identifier register (US_LINIR) is updated with the received character. The Identifier parity bits can be automatically computed and checked (see Section 30.7.8.8).The flags LINID and LINBK are reset by writing the bit RSTSTA at “1” in the Control register (US_CR). Figure 30-41. Header Reception Baud Rate Clock RXD Break Start StopStart Stop Break Field 1 0 1 0 1 0 1 0 ID0 ID1 ID2 ID3 ID4 ID5 ID6 ID7 13 dominant bits (at 0) Delimiter Bit Synch Byte = 0x55 Bit Bit Bit 1 recessive bit (at 1) LINBK LINID US_LINIR te RSTSTA=1 in US_CR 30.7.8.7 Slave Node Synchronization The synchronization is done only in Slave node configuration. The procedure is based on time measurement between falling edges of the Synch Field. The falling edges are available in distances of 2, 4, 6 and 8 bit times. Figure 30-42. Synch Field Synch Field 8 Tbit 2 Tbit 2 Tbit 2 Tbit 2 Tbit Start Stop bit bit The time measurement is made by a 19-bit counter clocked by the sampling clock (see Section 30.7.1). When the start bit of the Synch Field is detected the counter is reset. Then during the next eight t of the Synch bit Field, the counter is incremented. At the end of these eight t , the counter is stopped. At this moment, the 16 most bit SAM9M11 [DATASHEET] 533 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

significant bits of the counter (value divided by 8) gives the new clock divider (CD) and the 3 least significant bits of this value (the remainder) gives the new fractional part (FP). When the Synch Field has been received, the clock divider (CD) and the fractional part (FP) are updated in the Baud Rate Generator register (US_BRGR). Figure 30-43. Slave Node Synchronization Baud Rate Clock RXD Break Start StopStart Stop Break Field 1 0 1 0 1 0 1 0 ID0 ID1 ID2 ID3 ID4 ID5 ID6 ID7 Delimiter Bit Bit Bit Bit 13 dominant bits (at 0) Synch Byte = 0x55 1 recessive bit (at 1) LINIDRX Reset Synchro Counter 000_0011_0001_0110_1101 US_BRGR Initial CD 0000_0110_0010_1101 Clcok Divider (CD) US_BRGR Initial FP 101 Fractional Part (FP) The accuracy of the synchronization depends on several parameters:  The nominal clock frequency (f ) (the theoretical slave node clock frequency) Nom  The baud rate  The oversampling (OVER = 0 => 16X or OVER = 1 => 8X) The following formula is used to compute the deviation of the slave bit rate relative to the master bit rate after synchronization (f is the real slave node clock frequency). SLAVE Baudrate_deviation = 100×-[--α------×----8-----×-----(--2-----–----O-----v--e---r---)---+-----β----]----×----B----a---u---d---r--a---t-e--%  8×f  SLAVE    [α ×8×(2–Over)+β]×Baudrate Baudrate_deviation = 100×----------------------------------------------------------------------------------------%  8×f---T---O---L---_--U-1---0N---0S---Y----N---C---H---xFNom  –0.5≤α≤+0.5 -1<β<+1 f is the deviation of the real slave node clock from the nominal clock frequency. The LIN Standard TOL_UNSYNCH imposes that it must not exceed ±15%. The LIN Standard imposes also that for communication between two nodes, their bit rate must not differ by more than ±2%. This means that the Baudrate_deviation must not exceed ±1%. It follows from that, a minimum value for the nominal clock frequency:    [0.5×8×(2–Over)+1]×Baudrate f (min) = 100×-------------------------------------------------------------------------------------------Hz Nom  8×–----1---5--+1 ×1%   100   Examples:  Baudrate = 20 kbit/s, OVER = 0 (Oversampling 16X) => f (min) = 2.64 MHz Nom  Baudrate = 20 kbit/s, OVER = 1 (Oversampling 8X) => f (min) = 1.47 MHz Nom  Baudrate = 1 kbit/s, OVER = 0 (Oversampling 16X) => f (min) = 132 kHz Nom  Baudrate = 1 kbit/s, OVER = 1 (Oversampling 8X) => f (min) = 74 kHz Nom 534 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

If the fractional baud rate is not used, the accuracy of the synchronization becomes much lower. When the counter is stopped, the 16 most significant bits of the counter (value divided by 8) gives the new clock divider (CD). This value is rounded by adding the first insignificant bit. The equation of the Baudrate deviation is the same as given above, but the constants are as follows: –4≤α≤+4 -1<β<+1It follows from that, a minimum value for the nominal clock frequency:    [4×8×(2–Over)+1]×Baudrate f (min) = 100×--------------------------------------------------------------------------------------Hz Nom  8×–----1---5--+1 ×1%   100   Examples:  Baudrate = 20 kbit/s, OVER = 0 (Oversampling 16X) => f (min) = 19.12 MHz Nom  Baudrate = 20 kbit/s, OVER = 1 (Oversampling 8X) => f (min) = 9.71 MHz Nom  Baudrate = 1 kbit/s, OVER = 0 (Oversampling 16X) => f (min) = 956 kHz Nom  Baudrate = 1 kbit/s, OVER = 1 (Oversampling 8X) => f (min) = 485 kHz Nom 30.7.8.8 Identifier Parity A protected identifier consists of two sub-fields; the identifier and the identifier parity. Bits 0 to 5 are assigned to the identifier and bits 6 and 7 are assigned to the parity. The USART interface can generate/check these parity bits, but this feature can also be disabled. The user can choose between two modes by the PARDIS bit of the LIN Mode register (US_LINMR):  PARDIS = 0: ̶ During header transmission, the parity bits are computed and sent with the 6 least significant bits of the IDCHR field of the LIN Identifier register (US_LINIR). The bits 6 and 7 of this register are discarded. ̶ During header reception, the parity bits of the identifier are checked. If the parity bits are wrong, an Identifier Parity error occurs (see Section 30.7.3.9). Only the 6 least significant bits of the IDCHR field are updated with the received Identifier. The bits 6 and 7 are stuck at 0.  PARDIS = 1: ̶ During header transmission, all the bits of the IDCHR field of the LIN Identifier register (US_LINIR) are sent on the bus. ̶ During header reception, all the bits of the IDCHR field are updated with the received Identifier. SAM9M11 [DATASHEET] 535 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.7.8.9 Node Action Depending on the identifier, the node is affected – or not – by the LIN response. Consequently, after sending or receiving the identifier, the USART must be configured. There are three possible configurations:  PUBLISH: the node sends the response.  SUBSCRIBE: the node receives the response.  IGNORE: the node is not concerned by the response, it does not send and does not receive the response. This configuration is made by the field Node Action (NACT) in the US_LINMR (see Section 30.8.16). Example: a LIN cluster that contains a Master and two Slaves:  Data transfer from the Master to the Slave 1 and to the Slave 2: NACT(Master)=PUBLISH NACT(Slave1)=SUBSCRIBE NACT(Slave2)=SUBSCRIBE  Data transfer from the Master to the Slave 1 only: NACT(Master)=PUBLISH NACT(Slave1)=SUBSCRIBE NACT(Slave2)=IGNORE  Data transfer from the Slave 1 to the Master: NACT(Master)=SUBSCRIBE NACT(Slave1)=PUBLISH NACT(Slave2)=IGNORE  Data transfer from the Slave1 to the Slave2: NACT(Master)=IGNORE NACT(Slave1)=PUBLISH NACT(Slave2)=SUBSCRIBE  Data transfer from the Slave2 to the Master and to the Slave1: NACT(Master)=SUBSCRIBE NACT(Slave1)=SUBSCRIBE NACT(Slave2)=PUBLISH 536 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.7.8.10 Response Data Length The LIN response data length is the number of data fields (bytes) of the response excluding the checksum. The response data length can either be configured by the user or be defined automatically by bits 4 and 5 of the Identifier (compatibility to LIN Specification 1.1). The user can choose between these two modes by the DLM bit of the LIN Mode register (US_LINMR):  DLM = 0: the response data length is configured by the user via the DLC field of the LIN Mode register (US_LINMR). The response data length is equal to (DLC + 1) bytes. DLC can be programmed from 0 to 255, so the response can contain from 1 data byte up to 256 data bytes.  DLM = 1: the response data length is defined by the Identifier (IDCHR in US_LINIR) according to the table below. The DLC field of the LIN Mode register (US_LINMR) is discarded. The response can contain 2 or 4 or 8 data bytes. Table 30-15. Response Data Length if DLM = 1 IDCHR[5] IDCHR[4] Response Data Length [bytes] 0 0 2 0 1 2 1 0 4 1 1 8 Figure 30-44. Response Data Length User configuration: 1 - 256 data fields (DLC+1) Identifier configuration: 2/4/8 data fields Sync Sync Identifier Data Data Data Data Checksum Break Field Field Field Field Field Field Field 30.7.8.11 Checksum The last field of a frame is the checksum. The checksum contains the inverted 8- bit sum with carry, over all data bytes or all data bytes and the protected identifier. Checksum calculation over the data bytes only is called classic checksum and it is used for communication with LIN 1.3 slaves. Checksum calculation over the data bytes and the protected identifier byte is called enhanced checksum and it is used for communication with LIN 2.0 slaves. The USART can be configured to:  Send/Check an Enhanced checksum automatically (CHKDIS = 0 & CHKTYP = 0)  Send/Check a Classic checksum automatically (CHKDIS = 0 & CHKTYP = 1)  Not send/check a checksum (CHKDIS = 1) This configuration is made by the Checksum Type (CHKTYP) and Checksum Disable (CHKDIS) fields of the LIN Mode register (US_LINMR). If the checksum feature is disabled, the user can send it manually all the same, by considering the checksum as a normal data byte and by adding 1 to the response data length (see Section 30.7.8.10). SAM9M11 [DATASHEET] 537 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.7.8.12 Frame Slot Mode This mode is useful only for Master nodes. It respects the following rule: each frame slot shall be longer than or equal to t . Frame_Maximum If the Frame Slot Mode is enabled (FSDIS = 0) and a frame transfer has been completed, the TXRDY flag is set again only after t delay, from the start of frame. So the Master node cannot send a new header if the Frame_Maximum frame slot duration of the previous frame is inferior to t . Frame_Maximum If the Frame Slot Mode is disabled (FDIS = 1) and a frame transfer has been completed, the TXRDY flag is set again immediately. The t is calculated as below: Frame_Maximum If the Checksum is sent (CHKDIS = 0):  t = 34 x t Header_Nominal bit  t = 10 x (NData + 1) x t Response_Nominal bit  t = 1.4 x (t + t + 1)(Note:) Frame_Maximum Header_Nominal Response_Nominal  t = 1.4 x (34 + 10 x (DLC + 1 + 1) + 1) x t Frame_Maximum bit  t = (77 + 14 x DLC) x t Frame_Maximum bit If the Checksum is not sent (CHKDIS = 1):  t = 34 x t Header_Nominal bit  t = 10 x NData x t Response_Nominal bit  t = 1.4 x (t + t + 1(Note:)) Frame_Maximum Header_Nominal Response_Nominal  t = 1.4 x (34 + 10 x (DLC + 1) + 1) x t Frame_Maximum bit  t = (63 + 14 x DLC) x t Frame_Maximum bit Note: The term “+1” leads to an integer result for t (LIN Specification 1.3) Frame_Max Figure 30-45. Frame Slot Mode Frame slot = TFrame_Maximum Frame Inter- frame Response space space Header Data3 Response Break Synch Protected Data 1 Data N-1 Data N Checksum Identifier TXRDY Frame Slot Mode Frame Slot Mode Disabled Enabled Write US_LINID Write US_THR Data 1 Data 2 Data 3 Data N LINTC 30.7.8.13 LIN Errors Bit Error This error is generated when the USART is transmitting and if the transmitted value on the Tx line is different from the value sampled on the Rx line. If a bit error is detected, the transmission is aborted at the next byte border. 538 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Inconsistent Synch Field Error This error is generated in Slave node configuration if the Synch Field character received is other than 0x55. Parity Error This error is generated if the parity of the identifier is wrong. This error can be generated only if the parity feature is enabled (PARDIS = 0). Checksum Error This error is set if the received checksum is wrong. This error can be generated only if the checksum feature is enabled (CHKDIS = 0). Slave Not Responding Error This error is set when the USART expects a response from another node (NACT = SUBSCRIBE) but no valid message appears on the bus within the time frame given by the maximum length of the message frame, TFrame_Maximum (see Section 30.7.8.12). This error is disabled if the USART does not expect any message (NACT = PUBLISH or NACT = IGNORE). 30.7.8.14 LIN Frame Handling Master Node Configuration  Write TXEN and RXEN in US_CR to enable both the transmitter and the receiver.  Write USART_MODE in US_MR to select the LIN mode and the Master Node configuration.  Write CD and FP in US_BRGR to configure the baud rate.  Write NACT, PARDIS, CHKDIS, CHKTYPE, DLCM, FDIS and DLC in US_LINMR to configure the frame transfer.  Check that TXRDY in US_CSR is set to “1” Write IDCHR in US_LINIR to send the header What comes next depends on the NACT configuration:  Case 1: NACT = PUBLISH, the USART sends the response ̶ Wait until TXRDY in US_CSR rises ̶ Write TCHR in US_THR to send a byte ̶ If all the data have not been written, redo the two previous steps ̶ Wait until LINTC in US_CSR rises ̶ Check the LIN errors  Case 2: NACT = SUBSCRIBE, the USART receives the response ̶ Wait until RXRDY in US_CSR rises ̶ Read RCHR in US_RHR ̶ If all the data have not been read, redo the two previous steps ̶ Wait until LINTC in US_CSR rises ̶ Check the LIN errors  Case 3: NACT = IGNORE, the USART is not concerned by the response ̶ Wait until LINTC in US_CSR rises ̶ Check the LIN errors SAM9M11 [DATASHEET] 539 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 30-46. Master Node Configuration, NACT = PUBLISH Frame slot = TFrame_Maximum Frame Inter- frame Response space space Header Data3 Response Break Synch Protected Data 1 Data N-1 Data N Checksum Identifier TXRDY FSDIS=1 FSDIS=0 RXRDY Write US_LINIR Write US_THR Data 1 Data 2 Data 3 Data N LINTC Figure 30-47. Master Node Configuration, NACT = SUBSCRIBE Frame slot = TFrame_Maximum Frame Inter- frame Response space space Header Data3 Response Break Synch Protected Data 1 Data N-1 Data N Checksum Identifier TXRDY FSDIS=1 FSDIS=0 RXRDY Write US_LINIR Read US_RHR Data 1 Data N-2 Data N-1 Data N LINTC Figure 30-48. Master Node Configuration, NACT = IGNORE Frame slot = TFrame_Maximum Frame Inter- frame Response space space Header Data3 Response Break Synch Protected Data 1 Data N-1 Data N Checksum Identifier TXRDY FSDIS=1 FSDIS=0 RXRDY Write US_LINIR LINTC 540 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Slave Node Configuration  Write TXEN and RXEN in US_CR to enable both the transmitter and the receiver.  Write USART_MODE in US_MR to select the LIN mode and the Slave Node configuration.  Write CD and FP in US_BRGR to configure the baud rate.  Wait until LINID in US_CSR rises  Check LINISFE and LINPE errors  Read IDCHR in US_RHR Write NACT, PARDIS, CHKDIS, CHKTYPE, DLCM and DLC in US_LINMR to configure the frame transfer. IMPORTANT: if the NACT configuration for this frame is PUBLISH, the US_LINMR, must be write with NACT = PUBLISH even if this field is already correctly configured, in order to set the TXREADY flag and the corresponding PDC write transfer request. What comes next depends on the NACT configuration:  Case 1: NACT = PUBLISH, the LIN controller sends the response ̶ Wait until TXRDY in US_CSR rises ̶ Write TCHR in US_THR to send a byte ̶ If all the data have not been written, redo the two previous steps ̶ Wait until LINTC in US_CSR rises ̶ Check the LIN errors  Case 2: NACT = SUBSCRIBE, the USART receives the response ̶ Wait until RXRDY in US_CSR rises ̶ Read RCHR in US_RHR ̶ If all the data have not been read, redo the two previous steps ̶ Wait until LINTC in US_CSR rises ̶ Check the LIN errors  Case 3: NACT = IGNORE, the USART is not concerned by the response ̶ Wait until LINTC in US_CSR rises ̶ Check the LIN errors Figure 30-49. Slave Node Configuration, NACT = PUBLISH Break Synch Protected Data 1 Data N-1 Data N Checksum Identifier TXRDY RXRDY LINIDRX Read US_LINID Write US_THR Data 1 Data 2 Data 3 Data N LINTC SAM9M11 [DATASHEET] 541 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 30-50. Slave Node Configuration, NACT = SUBSCRIBE Break Synch Protected Data 1 Data N-1 Data N Checksum Identifier TXRDY RXRDY LINIDRX Read US_LINID Read US_RHR Data 1 Data N-2 Data N-1 Data N LINTC Figure 30-51. Slave Node Configuration, NACT = IGNORE Break Synch Protected Data 1 Data N-1 Data N Checksum Identifier TXRDY RXRDY LINIDRX Read US_LINID Read US_RHR LINTC 30.7.8.15 LIN Frame Handling With the Peripheral DMA Controller The USART can be used in association with the Peripheral DMA Controller (PDC) in order to transfer data directly into/from the on- and off-chip memories without any processor intervention. The PDC uses the trigger flags, TXRDY and RXRDY, to write or read into the USART. The PDC always writes in the Transmit Holding register (US_THR) and it always reads in the Receive Holding register (US_RHR). The size of the data written or read by the PDC in the USART is always a byte. Master Node Configuration The user can choose between two PDC modes by the PDCM bit in the LIN Mode register (US_LINMR):  PDCM = 1: the LIN configuration is stored in the WRITE buffer and it is written by the PDC in the Transmit Holding register US_THR (instead of the LIN Mode register US_LINMR). Because the PDC transfer size is limited to a byte, the transfer is split into two accesses. During the first access the bits, NACT, PARDIS, CHKDIS, CHKTYP, DLM and FDIS are written. During the second access the 8-bit DLC field is written.  PDCM = 0: the LIN configuration is not stored in the WRITE buffer and it must be written by the user in the LIN Mode register (US_LINMR). The WRITE buffer also contains the Identifier and the DATA, if the USART sends the response (NACT = PUBLISH). The READ buffer contains the DATA if the USART receives the response (NACT = SUBSCRIBE). 542 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 30-52. Master Node with PDC (PDCM = 1) WRITE BUFFER WRITE BUFFER NACT NACT PARDIS PARDIS CHKDIS CHKDIS CHKTYP CHKTYP DLM DLM FSDIS FSDIS DLC DLC NODE ACTION = PUBLISH NODE ACTION = SUBSCRIBE APB bus IDENTIFIER APB bus IDENTIFIER PDC USART3 READ BUFFER PDC USART3 (DMA) LIN CONTROLLER (DMA) RXRDY LIN CONTROLLER RXRDY DATA 0 DATA 0 TXRDY | | | | | | | | DATA N DATA N Figure 30-53. Master Node with PDC (PDCM = 0) WRITE BUFFER WRITE BUFFER IDENTIFIER IDENTIFIER NODE ACTION = PUBLISH NODE ACTION = SUBSCRIBE APB bus APB bus DATA 0 READ BUFFER PDC USART3 PDC USART3 (DMA) LIN CONTROLLER (DMA) RXRDY LIN CONTROLLER | RXRDY DATA 0 | | TXRDY | | | DATA N | | DATA N SAM9M11 [DATASHEET] 543 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Slave Node Configuration In this configuration, the PDC transfers only the DATA. The Identifier must be read by the user in the LIN Identifier register (US_LINIR). The LIN mode must be written by the user in the LIN Mode register (US_LINMR). The WRITE buffer contains the DATA if the USART sends the response (NACT = PUBLISH). The READ buffer contains the DATA if the USART receives the response (NACT = SUBSCRIBE). Figure 30-54. Slave Node with PDC WRITE BUFFER READ BUFFER DATA 0 DATA 0 NACT = SUBSCRIBE APB bus APB bus | | | PDC USART3 | PDC USART3 | (DMA) LIN CONTROLLER | (DMA) LIN CONTROLLER | TXRDY | RXRDY DATA N DATA N 30.7.8.16 Wake-up Request Any node in a sleeping LIN cluster may request a wake-up. In the LIN 2.0 specification, the wakeup request is issued by forcing the bus to the dominant state from 250 µs to 5ms. For this, it is necessary to send the character 0xF0 in order to impose 5 successive dominant bits. Whatever the baud rate is, this character respects the specified timings.  Baud rate min = 1 kbit/s -> t = 1ms -> 5 t = 5 ms bit bit  Baud rate max = 20 kbit/s -> t = 50 µs -> 5 t = 250 µs bit bit In the LIN 1.3 specification, the wakeup request should be generated with the character 0x80 in order to impose 8 successive dominant bits. The user can choose by the WKUPTYP bit in the LIN Mode register (US_LINMR) either to send a LIN 2.0 wakeup request (WKUPTYP = 0) or to send a LIN 1.3 wakeup request (WKUPTYP = 1). A wake-up request is transmitted by writing the Control Register (US_CR) with the LINWKUP bit at 1. Once the transfer is completed, the LINTC flag is asserted in the Status Register (US_SR). It is cleared by writing the Control Register (US_CR) with the RSTSTA bit at 1. 30.7.8.17 Bus Idle Time-out If the LIN bus is inactive for a certain duration, the slave nodes shall automatically enter in sleep mode. In the LIN 2.0 specification, this time-out is fixed at 4 seconds. In the LIN 1.3 specification, it is fixed at 25,000 t . bit In Slave Node configuration, the Receiver Time-out detects an idle condition on the RXD line. When a time-out is detected, the bit TIMEOUT in the Channel Status Register (US_CSR) rises and can generate an interrupt, thus indicating to the driver to go into sleep mode. The time-out delay period (during which the receiver waits for a new character) is programmed in the TO field of the Receiver Time-out Register (US_RTOR). If the TO field is programmed at 0, the Receiver Time-out is disabled and no time-out is detected. The TIMEOUT bit in US_CSR remains at 0. Otherwise, the receiver loads a 17-bit counter with the value programmed in TO. This counter is decremented at each bit period and reloaded each time a new character is received. If the counter reaches 0, the TIMEOUT bit in the Status Register rises. If STTTO is performed, the counter clock is stopped until a first character is received. If RETTO is performed, the counter starts counting down immediately from the value TO. 544 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 30-16. Receiver Time-out Programming LIN Specification Baud Rate Time-out period US_RTOR.TO 1 000 bit/s 4,000 2 400 bit/s 9,600 2.0 9 600 bit/s 4 s 38,400 19 200 bit/s 76,800 20 000 bit/s 80,000 1.3 - 25,000 t 25,000 bit 30.7.9 Test Modes The USART can be programmed to operate in three different test modes. The internal loopback capability allows on-board diagnostics. In the loopback mode the USART interface pins are disconnected or not and reconfigured for loopback internally or externally. 30.7.9.1 Normal Mode Normal mode connects the RXD pin on the receiver input and the transmitter output on the TXD pin. Figure 30-55. Normal Mode Configuration RXD Receiver TXD Transmitter 30.7.9.2 Automatic Echo Mode Automatic echo mode allows bit-by-bit retransmission. When a bit is received on the RXD pin, it is sent to the TXD pin, as shown in Figure 30-56. Programming the transmitter has no effect on the TXD pin. The RXD pin is still connected to the receiver input, thus the receiver remains active. Figure 30-56. Automatic Echo Mode Configuration RXD Receiver TXD Transmitter SAM9M11 [DATASHEET] 545 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.7.9.3 Local Loopback Mode Local loopback mode connects the output of the transmitter directly to the input of the receiver, as shown in Figure 30-57. The TXD and RXD pins are not used. The RXD pin has no effect on the receiver and the TXD pin is continuously driven high, as in idle state. Figure 30-57. Local Loopback Mode Configuration RXD Receiver TXD 1 Transmitter 30.7.9.4 Remote Loopback Mode Remote loopback mode directly connects the RXD pin to the TXD pin, as shown in Figure 30-58. The transmitter and the receiver are disabled and have no effect. This mode allows bit-by-bit retransmission. Figure 30-58. Remote Loopback Mode Configuration RXD 1 Receiver TXD Transmitter 546 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8 Universal Synchronous Asynchronous Receiver Transmitter (USART) User Interface Table 30-17. Register Mapping Offset Register Name Access Reset 0x0000 Control Register US_CR Write-only – 0x0004 Mode Register US_MR Read/Write 0x0 0x0008 Interrupt Enable Register US_IER Write-only – 0x000C Interrupt Disable Register US_IDR Write-only – 0x0010 Interrupt Mask Register US_IMR Read-only 0x0 0x0014 Channel Status Register US_CSR Read-only 0x0 0x0018 Receiver Holding Register US_RHR Read-only 0x0 0x001C Transmitter Holding Register US_THR Write-only – 0x0020 Baud Rate Generator Register US_BRGR Read/Write 0x0 0x0024 Receiver Time-out Register US_RTOR Read/Write 0x0 0x0028 Transmitter Timeguard Register US_TTGR Read/Write 0x0 0x2C–0x3C Reserved – – – 0x0040 FI DI Ratio Register US_FIDI Read/Write 0x174 0x0044 Number of Errors Register US_NER Read-only 0x0 0x0048 Reserved – – – 0x004C IrDA Filter Register US_IF Read/Write 0x0 0x0050 Manchester Encoder Decoder Register US_MAN Read/Write 0x30011004 0x0054 LIN Mode Register US_LINMR Read/Write 0x0 0x0058 LIN Identifier Register US_LINIR Read/Write(1) 0x0 0x5C–0xFC Reserved – – – 0x100–0x128 Reserved for PDC Registers – – – Notes: 1. Write is possible only in LIN Master node configuration. SAM9M11 [DATASHEET] 547 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.1 USART Control Register Name: US_CR Address: 0xFFF8C000 (0), 0xFFF90000 (1), 0xFFF94000 (2), 0xFFF98000 (3) Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – LINWKUP LINABT RTSDIS/RCS RTSEN/FCS – – 15 14 13 12 11 10 9 8 RETTO RSTNACK RSTIT SENDA STTTO STPBRK STTBRK RSTSTA 7 6 5 4 3 2 1 0 TXDIS TXEN RXDIS RXEN RSTTX RSTRX – – • RSTRX: Reset Receiver 0: No effect. 1: Resets the receiver. • RSTTX: Reset Transmitter 0: No effect. 1: Resets the transmitter. • RXEN: Receiver Enable 0: No effect. 1: Enables the receiver, if RXDIS is 0. • RXDIS: Receiver Disable 0: No effect. 1: Disables the receiver. • TXEN: Transmitter Enable 0: No effect. 1: Enables the transmitter if TXDIS is 0. • TXDIS: Transmitter Disable 0: No effect. 1: Disables the transmitter. • RSTSTA: Reset Status Bits 0: No effect. 1: Resets the status bits PARE, FRAME, OVRE, MANERR, LINBE, LINSFE, LINIPE, LINCE, LINSNRE and RXBRK in US_CSR. 548 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• STTBRK: Start Break 0: No effect. 1: Starts transmission of a break after the characters present in US_THR and the Transmit Shift Register have been trans- mitted. No effect if a break is already being transmitted. • STPBRK: Stop Break 0: No effect. 1: Stops transmission of the break after a minimum of one character length and transmits a high level during 12-bit periods. No effect if no break is being transmitted. • STTTO: Start Time-out 0: No effect. 1: Starts waiting for a character before clocking the time-out counter. Resets the status bit TIMEOUT in US_CSR. • SENDA: Send Address 0: No effect. 1: In Multidrop Mode only, the next character written to the US_THR is sent with the address bit set. • RSTIT: Reset Iterations 0: No effect. 1: Resets ITERATION in US_CSR. No effect if the ISO7816 is not enabled. • RSTNACK: Reset Non Acknowledge 0: No effect 1: Resets NACK in US_CSR. • RETTO: Rearm Time-out 0: No effect 1: Restart Time-out • RTSEN/FCS: Request to Send Enable/Force SPI Chip Select – If USART does not operate in SPI Master Mode (USART_MODE ≠ 0xE): 0: No effect. 1: Drives the pin RTS to 0. – If USART operates in SPI Master Mode (USART_MODE = 0xE): FCS = 0: No effect. FCS = 1: Forces the Slave Select Line NSS (RTS pin) to 0, even if USART is no transmitting, in order to address SPI slave devices supporting the CSAAT Mode (Chip Select Active After Transfer). SAM9M11 [DATASHEET] 549 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• RTSDIS/RCS: Request to Send Disable/Release SPI Chip Select – If USART does not operate in SPI Master Mode (USART_MODE ≠ 0xE): 0: No effect. 1: Drives the pin RTS to 1. – If USART operates in SPI Master Mode (USART_MODE = 0xE): RCS = 0: No effect. RCS = 1: Releases the Slave Select Line NSS (RTS pin). • LINABT: Abort LIN Transmission 0: No effect. 1: Abort the current LIN transmission. • LINWKUP: Send LIN Wakeup Signal 0: No effect: 1: Sends a wakeup signal on the LIN bus. 550 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.2 USART Mode Register Name: US_MR Address: 0xFFF8C004 (0), 0xFFF90004 (1), 0xFFF94004 (2), 0xFFF98004 (3) Access: Read/Write 31 30 29 28 27 26 25 24 ONEBIT MODSYNC MAN FILTER – MAX_ITERATION 23 22 21 20 19 18 17 16 VAR_SYNC DSNACK INACK OVER CLKO MODE9 MSBF/CPOL 15 14 13 12 11 10 9 8 CHMODE NBSTOP PAR SYNC/CPHA 7 6 5 4 3 2 1 0 CHRL USCLKS USART_MODE • USART_MODE USART_MODE Mode of the USART 0 0 0 0 Normal 0 0 0 1 RS485 0 0 1 0 Hardware Handshaking 0 1 0 0 IS07816 Protocol: T = 0 0 1 1 0 IS07816 Protocol: T = 1 1 0 0 0 IrDA 1 0 1 0 LIN Master 1 0 1 1 LIN Slave 1 1 1 0 SPI Master 1 1 1 1 SPI Slave Others Reserved • USCLKS: Clock Selection USCLKS Selected Clock 0 0 MCK 0 1 MCK/DIV (DIV = 8) 1 0 Reserved 1 1 SCK • CHRL: Character Length CHRL Character Length 0 0 5 bits 0 1 6 bits 1 0 7 bits 1 1 8 bits SAM9M11 [DATASHEET] 551 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• SYNC/CPHA: Synchronous Mode Select or SPI Clock Phase – If USART does not operate in SPI Mode (USART_MODE is ≠ 0xE and 0xF): SYNC = 0: USART operates in Asynchronous Mode. SYNC = 1: USART operates in Synchronous Mode. – If USART operates in SPI Mode (USART_MODE = 0xE or 0xF): CPHA = 0: Data is changed on the leading edge of SPCK and captured on the following edge of SPCK. CPHA = 1: Data is captured on the leading edge of SPCK and changed on the following edge of SPCK. CPHA determines which edge of SPCK causes data to change and which edge causes data to be captured. CPHA is used with CPOL to produce the required clock/data relationship between master and slave devices. • PAR: Parity Type PAR Parity Type 0 0 0 Even parity 0 0 1 Odd parity 0 1 0 Parity forced to 0 (Space) 0 1 1 Parity forced to 1 (Mark) 1 0 x No parity 1 1 x Multidrop mode • NBSTOP: Number of Stop Bits NBSTOP Asynchronous (SYNC = 0) Synchronous (SYNC = 1) 0 0 1 stop bit 1 stop bit 0 1 1.5 stop bits Reserved 1 0 2 stop bits 2 stop bits 1 1 Reserved Reserved • CHMODE: Channel Mode CHMODE Mode Description 0 0 Normal Mode 0 1 Automatic Echo. Receiver input is connected to the TXD pin. 1 0 Local Loopback. Transmitter output is connected to the Receiver Input. 1 1 Remote Loopback. RXD pin is internally connected to the TXD pin. • MSBF/CPOL: Bit Order or SPI Clock Polarity – If USART does not operate in SPI Mode (USART_MODE ≠ 0xE and 0xF): MSBF = 0: Least Significant Bit is sent/received first. MSBF = 1: Most Significant Bit is sent/received first. – If USART operates in SPI Mode (Slave or Master, USART_MODE = 0xE or 0xF): CPOL = 0: The inactive state value of SPCK is logic level zero. CPOL = 1: The inactive state value of SPCK is logic level one. CPOL is used to determine the inactive state value of the serial clock (SPCK). It is used with CPHA to produce the required clock/data relationship between master and slave devices. 552 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• MODE9: 9-bit Character Length 0: CHRL defines character length. 1: 9-bit character length. • CLKO: Clock Output Select 0: The USART does not drive the SCK pin. 1: The USART drives the SCK pin if USCLKS does not select the external clock SCK. • OVER: Oversampling Mode 0: 16x Oversampling. 1: 8x Oversampling. • INACK: Inhibit Non Acknowledge 0: The NACK is generated. 1: The NACK is not generated. • DSNACK: Disable Successive NACK 0: NACK is sent on the ISO line as soon as a parity error occurs in the received character (unless INACK is set). 1: Successive parity errors are counted up to the value specified in the MAX_ITERATION field. These parity errors gener- ate a NACK on the ISO line. As soon as this value is reached, no additional NACK is sent on the ISO line. The flag ITERATION is asserted. • VAR_SYNC: Variable Synchronization of Command/Data Sync Start Frame Delimiter 0: User defined configuration of command or data sync field depending on SYNC value. 1: The sync field is updated when a character is written into US_THR. • MAX_ITERATION Defines the maximum number of iterations in mode ISO7816, protocol T = 0. • FILTER: Infrared Receive Line Filter 0: The USART does not filter the receive line. 1: The USART filters the receive line using a three-sample filter (1/16-bit clock) (2 over 3 majority). • MAN: Manchester Encoder/Decoder Enable 0: Manchester Encoder/Decoder are disabled. 1: Manchester Encoder/Decoder are enabled. • MODSYNC: Manchester Synchronization Mode 0:The Manchester Start bit is a 0 to 1 transition 1: The Manchester Start bit is a 1 to 0 transition. • ONEBIT: Start Frame Delimiter Selector 0: Start Frame delimiter is COMMAND or DATA SYNC. 1: Start Frame delimiter is One Bit. SAM9M11 [DATASHEET] 553 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.3 USART Interrupt Enable Register Name: US_IER Address: 0xFFF8C008 (0), 0xFFF90008 (1), 0xFFF94008 (2), 0xFFF98008 (3) Access: Write-only 31 30 29 28 27 26 25 24 – – LINSNRE LINCE LINIPE LINISFE LINBE MANE 23 22 21 20 19 18 17 16 – – – – CTSIC – – – 15 14 13 12 11 10 9 8 LINTC LINID NACK/LINBK RXBUFF TXBUFE ITER/UNRE TXEMPTY TIMEOUT 7 6 5 4 3 2 1 0 PARE FRAME OVRE ENDTX ENDRX RXBRK TXRDY RXRDY • RXRDY: RXRDY Interrupt Enable • TXRDY: TXRDY Interrupt Enable • RXBRK: Receiver Break Interrupt Enable • ENDRX: End of Receive Transfer Interrupt Enable • ENDTX: End of Transmit Interrupt Enable • OVRE: Overrun Error Interrupt Enable • FRAME: Framing Error Interrupt Enable • PARE: Parity Error Interrupt Enable • TIMEOUT: Time-out Interrupt Enable • TXEMPTY: TXEMPTY Interrupt Enable • ITER/UNRE: Iteration or SPI Underrun Error Interrupt Enable • TXBUFE: Buffer Empty Interrupt Enable • RXBUFF: Buffer Full Interrupt Enable • NACK/LINBK: Non Acknowledge or LIN Break Sent or LIN Break Received Interrupt Enable • LINID: LIN Identifier Sent or LIN Identifier Received Interrupt Enable • LINTC: LIN Transfer Completed Interrupt Enable • CTSIC: Clear to Send Input Change Interrupt Enable • MANE: Manchester Error Interrupt Enable 554 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• LINBE: LIN Bus Error Interrupt Enable • LINISFE: LIN Inconsistent Synch Field Error Interrupt Enable • LINIPE: LIN Identifier Parity Interrupt Enable • LINCE: LIN Checksum Error Interrupt Enable • LINSNRE: LIN Slave Not Responding Error Interrupt Enable SAM9M11 [DATASHEET] 555 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.4 USART Interrupt Disable Register Name: US_IDR Address: 0xFFF8C00C (0), 0xFFF9000C (1), 0xFFF9400C (2), 0xFFF9800C (3) Access: Write-only 31 30 29 28 27 26 25 24 – – LINSNRE LINCE LINIPE LINISFE LINBE MANE 23 22 21 20 19 18 17 16 – – – – CTSIC – – – 15 14 13 12 11 10 9 8 LINTC LINID NACK/LINBK RXBUFF TXBUFE ITER/UNRE TXEMPTY TIMEOUT 7 6 5 4 3 2 1 0 PARE FRAME OVRE ENDTX ENDRX RXBRK TXRDY RXRDY • RXRDY: RXRDY Interrupt Disable • TXRDY: TXRDY Interrupt Disable • RXBRK: Receiver Break Interrupt Disable • ENDRX: End of Receive Transfer Interrupt Disable • ENDTX: End of Transmit Interrupt Disable • OVRE: Overrun Error Interrupt Disable • FRAME: Framing Error Interrupt Disable • PARE: Parity Error Interrupt Disable • TIMEOUT: Time-out Interrupt Disable • TXEMPTY: TXEMPTY Interrupt Disable • ITER/UNRE: Iteration or SPI Underrun Error Interrupt Enable • TXBUFE: Buffer Empty Interrupt Disable • RXBUFF: Buffer Full Interrupt Disable • NACK/LINBK: Non Acknowledge or LIN Break Sent or LIN Break Received Interrupt Disable • LINID: LIN Identifier Sent or LIN Identifier Received Interrupt Disable • LINTC: LIN Transfer Completed Interrupt Disable • CTSIC: Clear to Send Input Change Interrupt Disable • MANE: Manchester Error Interrupt Disable 556 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• LINBE: LIN Bus Error Interrupt Disable • LINISFE: LIN Inconsistent Synch Field Error Interrupt Disable • LINIPE: LIN Identifier Parity Interrupt Disable • LINCE: LIN Checksum Error Interrupt Disable • LINSNRE: LIN Slave Not Responding Error Interrupt Disable SAM9M11 [DATASHEET] 557 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.5 USART Interrupt Mask Register Name: US_IMR Address: 0xFFF8C010 (0), 0xFFF90010 (1), 0xFFF94010 (2), 0xFFF98010 (3) Access: Read-only 31 30 29 28 27 26 25 24 – – LINSNRE LINCE LINIPE LINISFE LINBE MANE 23 22 21 20 19 18 17 16 – – – – CTSIC – – – 15 14 13 12 11 10 9 8 LINTC LINID NACK/LINBK RXBUFF TXBUFE ITER/UNRE TXEMPTY TIMEOUT 7 6 5 4 3 2 1 0 PARE FRAME OVRE ENDTX ENDRX RXBRK TXRDY RXRDY • RXRDY: RXRDY Interrupt Mask • TXRDY: TXRDY Interrupt Mask • RXBRK: Receiver Break Interrupt Mask • ENDRX: End of Receive Transfer Interrupt Mask • ENDTX: End of Transmit Interrupt Mask • OVRE: Overrun Error Interrupt Mask • FRAME: Framing Error Interrupt Mask • PARE: Parity Error Interrupt Mask • TIMEOUT: Time-out Interrupt Mask • TXEMPTY: TXEMPTY Interrupt Mask • ITER/UNRE: Iteration or SPI Underrun Error Interrupt Enable • TXBUFE: Buffer Empty Interrupt Mask • RXBUFF: Buffer Full Interrupt Mask • NACK/LINBK: Non Acknowledge or LIN Break Sent or LIN Break Received Interrupt Mask • LINID: LIN Identifier Sent or LIN Identifier Received Interrupt Mask • LINTC: LIN Transfer Completed Interrupt Mask • CTSIC: Clear to Send Input Change Interrupt Mask • MANE: Manchester Error Interrupt Mask 558 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• LINBE: LIN Bus Error Interrupt Mask • LINISFE: LIN Inconsistent Synch Field Error Interrupt Mask • LINIPE: LIN Identifier Parity Interrupt Mask • LINCE: LIN Checksum Error Interrupt Mask • LINSNRE: LIN Slave Not Responding Error Interrupt Mask SAM9M11 [DATASHEET] 559 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.6 USART Channel Status Register Name: US_CSR Address: 0xFFF8C014 (0), 0xFFF90014 (1), 0xFFF94014 (2), 0xFFF98014 (3) Access: Read-only 31 30 29 28 27 26 25 24 – – LINSNRE LINCE LINIPE LINISFE LINBE MANERR 23 22 21 20 19 18 17 16 CTS – – – CTSIC – – – 15 14 13 12 11 10 9 8 LINTC LINID NACK/LINBK RXBUFF TXBUFE ITER/UNRE TXEMPTY TIMEOUT 7 6 5 4 3 2 1 0 PARE FRAME OVRE ENDTX ENDRX RXBRK TXRDY RXRDY • RXRDY: Receiver Ready 0: No complete character has been received since the last read of US_RHR or the receiver is disabled. If characters were being received when the receiver was disabled, RXRDY changes to 1 when the receiver is enabled. 1: At least one complete character has been received and US_RHR has not yet been read. • TXRDY: Transmitter Ready 0: A character is in the US_THR waiting to be transferred to the Transmit Shift Register, or an STTBRK command has been requested, or the transmitter is disabled. As soon as the transmitter is enabled, TXRDY becomes 1. 1: There is no character in the US_THR. • RXBRK: Break Received/End of Break 0: No Break received or End of Break detected since the last RSTSTA. 1: Break Received or End of Break detected since the last RSTSTA. • ENDRX: End of Receiver Transfer 0: The End of Transfer signal from the Receive PDC channel is inactive. 1: The End of Transfer signal from the Receive PDC channel is active. • ENDTX: End of Transmitter Transfer 0: The End of Transfer signal from the Transmit PDC channel is inactive. 1: The End of Transfer signal from the Transmit PDC channel is active. • OVRE: Overrun Error 0: No overrun error has occurred since the last RSTSTA. 1: At least one overrun error has occurred since the last RSTSTA. • FRAME: Framing Error 0: No stop bit has been detected low since the last RSTSTA. 1: At least one stop bit has been detected low since the last RSTSTA. 560 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• PARE: Parity Error 0: No parity error has been detected since the last RSTSTA. 1: At least one parity error has been detected since the last RSTSTA. • TIMEOUT: Receiver Time-out 0: There has not been a time-out since the last Start Time-out command (STTTO in US_CR) or the Time-out Register is 0. 1: There has been a time-out since the last Start Time-out command (STTTO in US_CR). • TXEMPTY: Transmitter Empty 0: There are characters in either US_THR or the Transmit Shift Register, or the transmitter is disabled. 1: There are no characters in US_THR, nor in the Transmit Shift Register. • ITER/UNRE: Max number of Repetitions Reached or SPI Underrun Error – If USART does not operate in SPI Slave Mode (USART_MODE ≠ 0xF): ITER = 0: Maximum number of repetitions has not been reached since the last RSTSTA. ITER = 1: Maximum number of repetitions has been reached since the last RSTSTA. – If USART operates in SPI Slave Mode (USART_MODE = 0xF): UNRE = 0: No SPI underrun error has occurred since the last RSTSTA. UNRE = 1: At least one SPI underrun error has occurred since the last RSTSTA. • TXBUFE: Transmission Buffer Empty 0: The signal Buffer Empty from the Transmit PDC channel is inactive. 1: The signal Buffer Empty from the Transmit PDC channel is active. • RXBUFF: Reception Buffer Full 0: The signal Buffer Full from the Receive PDC channel is inactive. 1: The signal Buffer Full from the Receive PDC channel is active. • NACK/LINBK Non Acknowledge or LIN Break Sent or LIN Break Received – If USART does not operate in LIN Mode (USART_MODE ≠ 0xA AND ≠ 0xB): 0: No Non Acknowledge has not been detected since the last RSTNACK. 1: At least one Non Acknowledge has been detected since the last RSTNACK. – If USART operates in LIN Master Mode (USART_MODE = 0xA): 0: No LIN Break has been sent since the last RSTSTA. 1:At least one LIN Break has been sent since the last RSTSTA. – If USART operates in LIN Slave Mode (USART_MODE = 0xB): 0: No LIN Break has received sent since the last RSTSTA. 1:At least one LIN Break has been received since the last RSTSTA. SAM9M11 [DATASHEET] 561 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• LINID: LIN Identifier Sent or LIN Identifier Received – If USART operates in LIN Master Mode (USART_MODE = 0xA): 0: No LIN Identifier has been sent since the last RSTSTA. 1:At least one LIN Identifier has been sent since the last RSTSTA. – If USART operates in LIN Slave Mode (USART_MODE = 0xB): 0: No LIN Identifier has been received since the last RSTSTA. 1:At least one LIN Identifier has been received since the last RSTSTA • LINTC: LIN Transfer Completed 0: The USART is idle or a LIN transfer is ongoing. 1: A LIN transfer has been completed since the last RSTSTA. • CTSIC: Clear to Send Input Change Flag 0: No input change has been detected on the CTS pin since the last read of US_CSR. 1: At least one input change has been detected on the CTS pin since the last read of US_CSR. • CTS: Image of CTS Input 0: CTS is at 0. 1: CTS is at 1. • MANERR: Manchester Error 0: No Manchester error has been detected since the last RSTSTA. 1: At least one Manchester error has been detected since the last RSTSTA. • LINBE: LIN Bit Error 0: No Bit Error has been detected since the last RSTSTA. 1: A Bit Error has been detected since the last RSTSTA. • LINISFE: LIN Inconsistent Synch Field Error 0: No LIN Inconsistent Synch Field Error has been detected since the last RSTSTA 1: The USART is configured as a Slave node and a LIN Inconsistent Synch Field Error has been detected since the last RSTSTA. • LINIPE: LIN Identifier Parity Error 0: No LIN Identifier Parity Error has been detected since the last RSTSTA. 1: A LIN Identifier Parity Error has been detected since the last RSTSTA. • LINCE: LIN Checksum Error 0: No LIN Checksum Error has been detected since the last RSTSTA. 1: A LIN Checksum Error has been detected since the last RSTSTA. • LINSNRE: LIN Slave Not Responding Error 0: No LIN Slave Not Responding Error has been detected since the last RSTSTA. 1: A LIN Slave Not Responding Error has been detected since the last RSTSTA. 562 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.7 USART Receive Holding Register Name: US_RHR Address: 0xFFF8C018 (0), 0xFFF90018 (1), 0xFFF94018 (2), 0xFFF98018 (3) Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 RXSYNH – – – – – – RXCHR 7 6 5 4 3 2 1 0 RXCHR • RXCHR: Received Character Last character received if RXRDY is set. • RXSYNH: Received Sync 0: Last Character received is a Data. 1: Last Character received is a Command. SAM9M11 [DATASHEET] 563 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.8 USART Transmit Holding Register Name: US_THR Address: 0xFFF8C01C (0), 0xFFF9001C (1), 0xFFF9401C (2), 0xFFF9801C (3) Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 TXSYNH – – – – – – TXCHR 7 6 5 4 3 2 1 0 TXCHR • TXCHR: Character to be Transmitted Next character to be transmitted after the current character if TXRDY is not set. • TXSYNH: Sync Field to be transmitted 0: The next character sent is encoded as a data. Start Frame Delimiter is DATA SYNC. 1: The next character sent is encoded as a command. Start Frame Delimiter is COMMAND SYNC. 564 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.9 USART Baud Rate Generator Register Name: US_BRGR Address: 0xFFF8C020 (0), 0xFFF90020 (1), 0xFFF94020 (2), 0xFFF98020 (3) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – FP 15 14 13 12 11 10 9 8 CD 7 6 5 4 3 2 1 0 CD • CD: Clock Divider ≠ USART_MODE ISO7816 SYNC = 1 or USART_MODE = SPI SYNC = 0 (Master or Slave) USART_MODE = CD OVER = 0 OVER = 1 ISO7816 0 Baud Rate Clock Disabled Baud Rate = Baud Rate = Baud Rate = Baud Rate = Selected 1–65535 Selected Clock/16/CD Selected Clock/8/CD Selected Clock /CD Clock/CD/FI_DI_RATIO • FP: Fractional Part 0: Fractional divider is disabled. 1–7: Baud rate resolution, defined by FP x 1/8. SAM9M11 [DATASHEET] 565 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.10USART Receiver Time-out Register Name: US_RTOR Address: 0xFFF8C024 (0), 0xFFF90024 (1), 0xFFF94024 (2), 0xFFF98024 (3) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – TO 15 14 13 12 11 10 9 8 TO 7 6 5 4 3 2 1 0 TO • TO: Time-out Value 0: The Receiver Time-out is disabled. 1–131071: The Receiver Time-out is enabled and the Time-out delay is TO x Bit Period. 566 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.11 USART Transmitter Timeguard Register Name: US_TTGR Address: 0xFFF8C028 (0), 0xFFF90028 (1), 0xFFF94028 (2), 0xFFF98028 (3) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 TG • TG: Timeguard Value 0: The Transmitter Timeguard is disabled. 1–255: The Transmitter timeguard is enabled and the timeguard delay is TG x Bit Period. SAM9M11 [DATASHEET] 567 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.12USART FI DI RATIO Register Name: US_FIDI Address: 0xFFF8C040 (0), 0xFFF90040 (1), 0xFFF94040 (2), 0xFFF98040 (3) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – FI_DI_RATIO 7 6 5 4 3 2 1 0 FI_DI_RATIO • FI_DI_RATIO: FI Over DI Ratio Value 0: If ISO7816 mode is selected, the Baud Rate Generator generates no signal. 1–2047: If ISO7816 mode is selected, the Baud Rate is the clock provided on SCK divided by FI_DI_RATIO. 568 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.13USART Number of Errors Register Name: US_NER Address: 0xFFF8C044 (0), 0xFFF90044 (1), 0xFFF94044 (2), 0xFFF98044 (3) Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 NB_ERRORS • NB_ERRORS: Number of Errors Total number of errors that occurred during an ISO7816 transfer. This register automatically clears when read. SAM9M11 [DATASHEET] 569 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.14USART IrDA FILTER Register Name: US_IF Address: 0xFFF8C04C (0), 0xFFF9004C (1), 0xFFF9404C (2), 0xFFF9804C (3) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 IRDA_FILTER • IRDA_FILTER: IrDA Filter Sets the filter of the IrDA demodulator. 570 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.15USART Manchester Configuration Register Name: US_MAN Address: 0xFFF8C050 (0), 0xFFF90050 (1), 0xFFF94050 (2), 0xFFF98050 (3) Access: Read/Write 31 30 29 28 27 26 25 24 – DRIFT 1 RX_MPOL – – RX_PP 23 22 21 20 19 18 17 16 – – – – RX_PL 15 14 13 12 11 10 9 8 – – – TX_MPOL – – TX_PP 7 6 5 4 3 2 1 0 – – – – TX_PL • TX_PL: Transmitter Preamble Length 0: The Transmitter Preamble pattern generation is disabled 1–15: The Preamble Length is TX_PL x Bit Period • TX_PP: Transmitter Preamble Pattern TX_PP Preamble Pattern default polarity assumed (TX_MPOL field not set) 0 0 ALL_ONE 0 1 ALL_ZERO 1 0 ZERO_ONE 1 1 ONE_ZERO • TX_MPOL: Transmitter Manchester Polarity 0: Logic Zero is coded as a zero-to-one transition, Logic One is coded as a one-to-zero transition. 1: Logic Zero is coded as a one-to-zero transition, Logic One is coded as a zero-to-one transition. • RX_PL: Receiver Preamble Length 0: The receiver preamble pattern detection is disabled 1–15: The detected preamble length is RX_PL x Bit Period • RX_PP: Receiver Preamble Pattern detected RX_PP Preamble Pattern default polarity assumed (RX_MPOL field not set) 0 0 ALL_ONE 0 1 ALL_ZERO 1 0 ZERO_ONE 1 1 ONE_ZERO • RX_MPOL: Receiver Manchester Polarity 0: Logic Zero is coded as a zero-to-one transition, Logic One is coded as a one-to-zero transition. 1: Logic Zero is coded as a one-to-zero transition, Logic One is coded as a zero-to-one transition. SAM9M11 [DATASHEET] 571 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DRIFT: Drift compensation 0: The USART can not recover from an important clock drift 1: The USART can recover from clock drift. The 16X clock mode must be enabled. 572 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.16USART3 LIN Mode Register Name: US_LINMR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – PDCM 15 14 13 12 11 10 9 8 DLC 7 6 5 4 3 2 1 0 WKUPTYP FSDIS DLM CHKTYP CHKDIS PARDIS NACT • NACT: LIN Node Action NACT Mode Description 0 0 PUBLISH: The USART transmits the response. 0 1 SUBSCRIBE: The USART receives the response. 1 0 IGNORE: The USART does not transmit and does not receive the response. 1 1 Reserved • PARDIS: Parity Disable 0: In Master node configuration, the Identifier Parity is computed and sent automatically. In Master node and Slave node configuration, the parity is checked automatically. 1:Whatever the node configuration is, the Identifier parity is not computed/sent and it is not checked. • CHKDIS: Checksum Disable 0: In Master node configuration, the checksum is computed and sent automatically. In Slave node configuration, the check- sum is checked automatically. 1: Whatever the node configuration is, the checksum is not computed/sent and it is not checked. • CHKTYP: Checksum Type 0: LIN 2.0 “Enhanced” Checksum 1: LIN 1.3 “Classic” Checksum • DLM: Data Length Mode 0: The response data length is defined by the field DLC of this register. 1: The response data length is defined by the bits 5 and 6 of the Identifier (IDCHR in US_LINIR). • FDIS: Frame Slot Mode Disable 0: The Frame Slot Mode is enabled. 1: The Frame Slot Mode is disabled. SAM9M11 [DATASHEET] 573 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• WKUPTYP: Wakeup Signal Type 0: setting the bit LINWKUP in the control register sends a LIN 2.0 wakeup signal. 1: setting the bit LINWKUP in the control register sends a LIN 1.3 wakeup signal. • DLC: Data Length Control 0–255: Defines the response data length if DLM = 0,in that case the response data length is equal to DLC+1 bytes. • PDCM: PDC Mode 0: The LIN mode register US_LINMR is not written by the PDC. 1: The LIN mode register US_LINMR (excepting that flag) is written by the PDC. 574 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

30.8.17USART3 LIN Identifier Register Name: US_LINIR Access: Read/Write or Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 IDCHR • IDCHR: Identifier Character If USART_MODE = 0xA (Master node configuration): IDCHR is Read/Write and its value is the Identifier character to be transmitted. if USART_MODE = 0xB (Slave node configuration): IDCHR is Read-only and its value is the last Identifier character that has been received. SAM9M11 [DATASHEET] 575 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31. Two-wire Interface (TWI) 31.1 Description The Atmel Two-wire Interface (TWI) interconnects components on a unique two-wire bus, made up of one clock line and one data line with speeds of up to 400 Kbits per second, based on a byte-oriented transfer format. It can be used with any Atmel Two-wire Interface bus Serial EEPROM and I²C compatible device such as Real-time Clock (RTC), Dot Matrix/Graphic LCD Controllers and Temperature Sensor, to name but a few. The TWI is programmable as a master or a slave with sequential or single-byte access. Multiple master capability is supported. Arbitration of the bus is performed internally and puts the TWI in slave mode automatically if the bus arbitration is lost. A configurable baud rate generator permits the output data rate to be adapted to a wide range of core clock frequencies. Below, Table 31-1 lists the compatibility level of the Atmel Two-wire Interface in Master Mode and a full I2C compatible device. Table 31-1. Atmel TWI compatibility with I2C Standard I2C Standard Atmel TWI Standard Mode Speed (100 kHz) Supported Fast Mode Speed (400 kHz) Supported 7 or 10 bits Slave Addressing Supported START BYTE(1) Not Supported Repeated Start (Sr) Condition Supported ACK and NACK Management Supported Slope control and input filtering (Fast mode) Not Supported Clock stretching Supported Multi Master Capability Supported Note: 1. START + b000000001 + Ack + Sr 31.2 Embedded Characteristics  Compatibility with standard two-wire serial memory  One, two or three bytes for slave address  Sequential read/write operations  Supports either master or slave modes  Compatible with Standard Two-wire Serial Memories  Master, Multi-master and Slave Mode Operation  Bit Rate: Up to 400 Kbits  General Call Supported in Slave mode 576 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.3 List of Abbreviations Table 31-2. Abbreviations Abbreviation Description TWI Two-wire Interface A Acknowledge NA Non Acknowledge P Stop S Start Sr Repeated Start SADR Slave Address ADR Any address except SADR R Read W Write 31.4 Block Diagram Figure 31-1. Block Diagram APB Bridge TWCK PIO TWD Two-wire Interface MCK PMC TWI Interrupt AIC SAM9M11 [DATASHEET] 577 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.5 Application Block Diagram Figure 31-2. Application Block Diagram VDD Rp Rp TWD Host with TWI TWCK Interface Atmel TWI I²C LCD I²C Temp. I²C RTC Serial EEPROM Controller Sensor Slave 1 Slave 2 Slave 3 Slave 4 Rp: Pull up value as given by the I²C Standard 31.5.1 I/O Lines Description Table 31-3. I/O Lines Description Pin Name Pin Description Type TWD Two-wire Serial Data Input/Output TWCK Two-wire Serial Clock Input/Output 31.6 Product Dependencies 31.6.1 I/O Lines Both TWD and TWCK are bidirectional lines, connected to a positive supply voltage via a current source or pull-up resistor (see Figure 31-2). When the bus is free, both lines are high. The output stages of devices connected to the bus must have an open-drain or open-collector to perform the wired-AND function. TWD and TWCK pins may be multiplexed with PIO lines. To enable the TWI, the programmer must perform the following step:  Program the PIO controller to dedicate TWD and TWCK as peripheral lines. The user must not program TWD and TWCK as open-drain. It is already done by the hardware. Table 31-4. I/O Lines Instance Signal I/O Line Peripheral TWI0 TWCK0 PA21 A TWI0 TWD0 PA20 A TWI1 TWCK1 PB11 A TWI1 TWD1 PB10 A 31.6.2 Power Management  Enable the peripheral clock. The TWI interface may be clocked through the Power Management Controller (PMC), thus the programmer must first configure the PMC to enable the TWI clock. 578 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.6.3 Interrupt The TWI interface has an interrupt line connected to the Advanced Interrupt Controller (AIC). In order to handle interrupts, the AIC must be programmed before configuring the TWI. Table 31-5. Peripheral IDs Instance ID TWI0 12 TWI1 13 31.7 Functional Description 31.7.1 Transfer Format The data put on the TWD line must be 8 bits long. Data is transferred MSB first; each byte must be followed by an acknowledgement. The number of bytes per transfer is unlimited (see Figure 31-4). Each transfer begins with a START condition and terminates with a STOP condition (see Figure 31-3).  A high-to-low transition on the TWD line while TWCK is high defines the START condition.  A low-to-high transition on the TWD line while TWCK is high defines a STOP condition. Figure 31-3. START and STOP Conditions TWD TWCK Start Stop Figure 31-4. Transfer Format TWD TWCK Start Address R/W Ack Data Ack Data Ack Stop 31.7.2 Modes of Operation The TWI has six modes of operations:  Master transmitter mode  Master receiver mode  Multi-master transmitter mode  Multi-master receiver mode  Slave transmitter mode  Slave receiver mode These modes are described in the following sections. SAM9M11 [DATASHEET] 579 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.7.3 Master Mode 31.7.3.1 Definition The Master is the device that starts a transfer, generates a clock and stops it. 31.7.3.2 Application Block Diagram Figure 31-5. Master Mode Typical Application Block Diagram VDD Rp Rp TWD Host with TWI TWCK Interface Atmel TWI I²C LCD I²C Temp. I²C RTC Serial EEPROM Controller Sensor Slave 1 Slave 2 Slave 3 Slave 4 Rp: Pull up value as given by the I²C Standard 31.7.3.3 Programming Master Mode The following registers have to be programmed before entering Master mode: 1. DADR (+ IADRSZ + IADR if a 10 bit device is addressed): The device address is used to access slave devices in read or write mode. 2. CKDIV + CHDIV + CLDIV: Clock Waveform. 3. SVDIS: Disable the slave mode. 4. MSEN: Enable the master mode. 31.7.3.4 Master Transmitter Mode After the master initiates a Start condition when writing into the Transmit Holding Register, TWI_THR, it sends a 7- bit slave address, configured in the Master Mode register (DADR in TWI_MMR), to notify the slave device. The bit following the slave address indicates the transfer direction, 0 in this case (MREAD = 0 in TWI_MMR). The TWI transfers require the slave to acknowledge each received byte. During the acknowledge clock pulse (9th pulse), the master releases the data line (HIGH), enabling the slave to pull it down in order to generate the acknowledge. The master polls the data line during this clock pulse and sets the Not Acknowledge bit (NACK) in the status register if the slave does not acknowledge the byte. As with the other status bits, an interrupt can be generated if enabled in the interrupt enable register (TWI_IER). If the slave acknowledges the byte, the data written in the TWI_THR, is then shifted in the internal shifter and transferred. When an acknowledge is detected, the TXRDY bit is set until a new write in the TWI_THR. While no new data is written in the TWI_THR, the Serial Clock Line is tied low. When new data is written in the TWI_THR, the SCL is released and the data is sent. To generate a STOP event, the STOP command must be performed by writing in the STOP field of TWI_CR. After a Master Write transfer, the Serial Clock line is stretched (tied low) while no new data is written in the TWI_THR or until a STOP command is performed. See Figure 31-6, Figure 31-7, and Figure 31-8. 580 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 31-6. Master Write with One Data Byte STOP Command sent (write in TWI_CR) TWD S DADR W A DATA A P TXCOMP TXRDY Write THR (DATA) Figure 31-7. Master Write with Multiple Data Bytes STOP command performed (by writing in the TWI_CR) TWD S DADR W A DATA n A DATA n+1 A DATA n+2 A P TWCK TXCOMP TXRDY Write THR (Data n) Write THR (Data n+1) Write THR (Data n+2) Last data sent Figure 31-8. Master Write with One Byte Internal Address and Multiple Data Bytes STOP command performed (by writing in the TWI_CR) TWD S DADR W A IADR A DATA n A DATA n+1 A DATA n+2 A P TWCK TXCOMP TXRDY Write THR (Data n) Write THR (Data n+1) Write THR (Data n+2) Last data sent SAM9M11 [DATASHEET] 581 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.7.3.5 Master Receiver Mode The read sequence begins by setting the START bit. After the start condition has been sent, the master sends a 7- bit slave address to notify the slave device. The bit following the slave address indicates the transfer direction, 1 in this case (MREAD = 1 in TWI_MMR). During the acknowledge clock pulse (9th pulse), the master releases the data line (HIGH), enabling the slave to pull it down in order to generate the acknowledge. The master polls the data line during this clock pulse and sets the NACK bit in the status register if the slave does not acknowledge the byte. If an acknowledge is received, the master is then ready to receive data from the slave. After data has been received, the master sends an acknowledge condition to notify the slave that the data has been received except for the last data, after the stop condition. See Figure 31-9. When the RXRDY bit is set in the status register, a character has been received in the receive-holding register (TWI_RHR). The RXRDY bit is reset when reading the TWI_RHR. When a single data byte read is performed, with or without internal address (IADR), the START and STOP bits must be set at the same time. See Figure 31-9. When a multiple data byte read is performed, with or without internal address (IADR), the STOP bit must be set after the next-to-last data received. See Figure 31-10. For Internal Address usage see Section 31.7.3.6. Figure 31-9. Master Read with One Data Byte TWD S DADR R A DATA N P TXCOMP Write START & STOP Bit RXRDY Read RHR Figure 31-10. Master Read with Multiple Data Bytes TWD S DADR R A DATA n A DATA (n+1) A DATA (n+m)-1 A DATA (n+m) N P TXCOMP Write START Bit RXRDY Read RHR Read RHR Read RHR Read RHR DATA n DATA (n+1) DATA (n+m)-1 DATA (n+m) Write STOP Bit after next-to-last data read 582 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.7.3.6 Internal Address The TWI interface can perform various transfer formats: Transfers with 7-bit slave address devices and 10-bit slave address devices. 7-bit Slave Addressing When Addressing 7-bit slave devices, the internal address bytes are used to perform random address (read or write) accesses to reach one or more data bytes, within a memory page location in a serial memory, for example. When performing read operations with an internal address, the TWI performs a write operation to set the internal address into the slave device, and then switch to Master Receiver mode. Note that the second start condition (after sending the IADR) is sometimes called “repeated start” (Sr) in I2C fully-compatible devices. See Figure 31-12. See Figure 31-11 and Figure 31-13 for Master Write operation with internal address. The three internal address bytes are configurable through the Master Mode register (TWI_MMR). If the slave device supports only a 7-bit address, i.e., no internal address, IADRSZ must be set to 0. In the figures below the following abbreviations are used:  S Start  Sr Repeated Start  P Stop  W Write  R Read  A Acknowledge  N Not Acknowledge  DADR Device Address  IADR Internal Address Figure 31-11. Master Write with One, Two or Three Bytes Internal Address and One Data Byte Three bytes internal address TWD S DADR W A IADR(23:16) A IADR(15:8) A IADR(7:0) A DATA A P Two bytes internal address TWD S DADR W A IADR(15:8) A IADR(7:0) A DATA A P One byte internal address TWD S DADR W A IADR(7:0) A DATA A P Figure 31-12. Master Read with One, Two or Three Bytes Internal Address and One Data Byte Three bytes internal address TWD S DADR W A IADR(23:16) A IADR(15:8) A IADR(7:0) A Sr DADR R A DATA N P Two bytes internal address TWD S DADR W A IADR(15:8) A IADR(7:0) A Sr DADR R A DATA N P One byte internal address TWD S DADR W A IADR(7:0) A Sr DADR R A DATA N P SAM9M11 [DATASHEET] 583 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

10-bit Slave Addressing For a slave address higher than 7 bits, the user must configure the address size (IADRSZ) and set the other slave address bits in the internal address register (TWI_IADR). The two remaining Internal address bytes, IADR[15:8] and IADR[23:16] can be used the same as in 7-bit Slave Addressing. Example: Address a 10-bit device (10-bit device address is b1 b2 b3 b4 b5 b6 b7 b8 b9 b10) 1. Program IADRSZ = 1, 2. Program DADR with 1 1 1 1 0 b1 b2 (b1 is the MSB of the 10-bit address, b2, etc.) 3. Program TWI_IADR with b3 b4 b5 b6 b7 b8 b9 b10 (b10 is the LSB of the 10-bit address) Figure 31-13 below shows a byte write to an Atmel AT24LC512 EEPROM. This demonstrates the use of internal addresses to access the device. Figure 31-13. Internal Address Usage S W T R S A I T R Device T FIRST SECOND O T Address E WORD ADDRESS WORD ADDRESS DATA P 0 M LR A M A LA A S S / C S C SC C B BWK B K BK K 31.7.3.7 SMBUS Quick Command (Master Mode Only) The TWI interface can perform a Quick Command: 1. Configure the master mode (DADR, CKDIV, etc.). 2. Write the MREAD bit in the TWI_MMR at the value of the one-bit command to be sent. 3. Start the transfer by setting the QUICK bit in the TWI_CR. Figure 31-14. SMBUS Quick Command TWD S DADR R/W A P TXCOMP TXRDY Write QUICK command in TWI_CR 31.7.3.8 Read/Write Flowcharts The flowcharts in the following figures provide examples for read and write operations. A polling or interrupt method can be used to check the status bits. The interrupt method requires that the interrupt enable register (TWI_IER) be configured first. 584 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 31-15. TWI Write Operation with Single Data Byte without Internal Address BEGIN Set TWI clock (CLDIV, CHDIV, CKDIV) in TWI_CWGR (Needed only once) Set the Control register: - Master enable TWI_CR = MSEN + SVDIS Set the Master Mode register: - Device slave address (DADR) - Transfer direction bit Write ==> bit MREAD = 0 Load Transmit register TWI_THR = Data to send Write STOP Command TWI_CR = STOP Read Status register No TXRDY = 1? Yes Read Status register No TXCOMP = 1? Yes Transfer finished SAM9M11 [DATASHEET] 585 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 31-16. TWI Write Operation with Single Data Byte and Internal Address BEGIN Set TWI clock (CLDIV, CHDIV, CKDIV) in TWI_CWGR (Needed only once) Set the Control register: - Master enable TWI_CR = MSEN + SVDIS Set the Master Mode register: - Device slave address (DADR) - Internal address size (IADRSZ) - Transfer direction bit Write ==> bit MREAD = 0 Set the internal address TWI_IADR = address Load transmit register TWI_THR = Data to send Write STOP command TWI_CR = STOP Read Status register No TXRDY = 1? Yes Read Status register TXCOMP = 1? No Yes Transfer finished 586 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 31-17. TWI Write Operation with Multiple Data Bytes with or without Internal Address BEGIN Set TWI clock (CLDIV, CHDIV, CKDIV) in TWI_CWGR (Needed only once) Set the Control register: - Master enable TWI_CR = MSEN + SVDIS Set the Master Mode register: - Device slave address - Internal address size (if IADR used) - Transfer direction bit Write ==> bit MREAD = 0 No Internal address size = 0? Set the internal address TWI_IADR = address Yes Load Transmit register TWI_THR = Data to send Read Status register TWI_THR = data to send No TXRDY = 1? Yes Data to send? Yes Write STOP Command TWI_CR = STOP Read Status register Yes No TXCOMP = 1? END SAM9M11 [DATASHEET] 587 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 31-18. TWI Read Operation with Single Data Byte without Internal Address BEGIN Set TWI clock (CLDIV, CHDIV, CKDIV) in TWI_CWGR (Needed only once) Set the Control register: - Master enable TWI_CR = MSEN + SVDIS Set the Master Mode register: - Device slave address - Transfer direction bit Read ==> bit MREAD = 1 Start the transfer TWI_CR = START | STOP Read status register No RXRDY = 1? Yes Read Receive Holding Register Read Status register No TXCOMP = 1? Yes END 588 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 31-19. TWI Read Operation with Single Data Byte and Internal Address BEGIN Set TWI clock (CLDIV, CHDIV, CKDIV) in TWI_CWGR (Needed only once) Set the Control register: - Master enable TWI_CR = MSEN + SVDIS Set the Master Mode register: - Device slave address - Internal address size (IADRSZ) - Transfer direction bit Read ==> bit MREAD = 1 Set the internal address TWI_IADR = address Start the transfer TWI_CR = START | STOP Read Status register No RXRDY = 1? Yes Read Receive Holding register Read Status register No TXCOMP = 1? Yes END SAM9M11 [DATASHEET] 589 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 31-20. TWI Read Operation with Multiple Data Bytes with or without Internal Address BEGIN Set TWI clock (CLDIV, CHDIV, CKDIV) in TWI_CWGR (Needed only once) Set the Control register: - Master enable TWI_CR = MSEN + SVDIS Set the Master Mode register: - Device slave address - Internal address size (if IADR used) - Transfer direction bit Read ==> bit MREAD = 1 Internal address size = 0? Set the internal address TWI_IADR = address Yes Start the transfer TWI_CR = START Read Status register No RXRDY = 1? Yes Read Receive Holding register (TWI_RHR) No Last data to read but one? Yes Stop the transfer TWI_CR = STOP Read Status register No RXRDY = 1? Yes Read Receive Holding register (TWI_RHR) Read status register No TXCOMP = 1? Yes END 590 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.7.4 Multi- master Mode 31.7.4.1 Definition More than one master may handle the bus at the same time without data corruption by using arbitration. Arbitration starts as soon as two or more masters place information on the bus at the same time, and stops (arbitration is lost) for the master that intends to send a logical one while the other master sends a logical zero. As soon as arbitration is lost by a master, it stops sending data and listens to the bus in order to detect a stop. When the stop is detected, the master who has lost arbitration may put its data on the bus by respecting arbitration. Arbitration is illustrated in Figure 31-22 on page 592. 31.7.4.2 Different Multi-master Modes Two multi-master modes may be distinguished: 1. TWI is considered as a Master only and will never be addressed. 2. TWI may be either a Master or a Slave and may be addressed. Note: In both Multi-master modes arbitration is supported. TWI as Master Only In this mode, TWI is considered as a Master only (MSEN is always at one) and must be driven like a Master with the ARBLST (ARBitration Lost) flag in addition. If arbitration is lost (ARBLST = 1), the programmer must reinitiate the data transfer. If the user starts a transfer (ex.: DADR + START + W + Write in THR) and if the bus is busy, the TWI automatically waits for a STOP condition on the bus to initiate the transfer (see Figure 31-21 on page 592). Note: The state of the bus (busy or free) is not indicated in the user interface. TWI as Master or Slave The automatic reversal from Master to Slave is not supported in case of a lost arbitration. Then, in the case where TWI may be either a Master or a Slave, the programmer must manage the pseudo Multi- master mode described in the steps below. 1. Program TWI in Slave mode (SADR + MSDIS + SVEN) and perform Slave Access (if TWI is addressed). 2. If TWI has to be set in Master mode, wait until TXCOMP flag is at 1. 3. Program Master mode (DADR + SVDIS + MSEN) and start the transfer (ex: START + Write in THR). 4. As soon as the Master mode is enabled, TWI scans the bus in order to detect if it is busy or free. When the bus is considered as free, TWI initiates the transfer. 5. As soon as the transfer is initiated and until a STOP condition is sent, the arbitration becomes relevant and the user must monitor the ARBLST flag. 6. If the arbitration is lost (ARBLST is set to 1), the user must program the TWI in Slave mode in the case where the Master that won the arbitration wanted to access the TWI. 7. If TWI has to be set in Slave mode, wait until TXCOMP flag is at 1 and then program the Slave mode. Note: In the case where the arbitration is lost and TWI is addressed, TWI will not acknowledge even if it is programmed in Slave mode as soon as ARBLST is set to 1. Then, the Master must repeat SADR. SAM9M11 [DATASHEET] 591 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 31-21. Programmer Sends Data While the Bus is Busy TWCK STOP sent by the master START sent by the TWI TWD DATA sent by a master DATA sent by the TWI Bus is busy Bus is free TWI DATA transfer Transfer is kept A transfer is programmed Bus is considered as free (DADR + W + START + Write THR) Transfer is initiated Figure 31-22. Arbitration Cases TWCK TWD TWCK Arbitration is lost Data from a Master S 1 0 0 1 1 P S 1 0 1 The master stops sending data Arbitration is lost Data from TWI S 1 0 1 S 1 0 0 1 1 TWI stops sending data TWD S 1 0 0 1 1 Data from the master P S 1 0 0 1 1 Data from the TWI ARBLST Bus is busy Bus is free TWI DATA transfer Transfer is kept A transfer is programmed Transfer is stopped Bus is considered as free (DADR + W + START + Write THR) Transfer is programmed again Transfer is initiated (DADR + W + START + Write THR) The flowchart shown in Figure 31-23 on page 593 gives an example of read and write operations in Multi-master mode. 592 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 31-23. Multi-master Flowchart START Programm the SLAVE mode: SADR + MSDIS + SVEN Read Status Register Yes No SVACC = 1 ? GACC = 1 ? No No SVREAD = 0 ? No No EOSACC = 1 ? Yes TXRDY= 1 ? Yes Yes No Write in TWI_THR TXCOMP = 1 ? No RXRDY= 0 ? Yes Yes No Need to perform Read TWI_RHR a master access ? GENERAL CALL TREATMENT Yes Decoding of the programming sequence Prog seq No OK ? Change SADR Program the Master mode DADR + SVDIS + MSEN + CLK + R / W Read Status Register Yes No ARBLST = 1 ? Yes No MREAD = 1 ? Yes Yes RXRDY= 0 ? TXRDY= 0 ? No No Yes Yes Read TWI_RHR Data to read? Data to send ? Write in TWI_THR No No Stop Transfer TWI_CR = STOP Read Status Register Yes No TXCOMP = 0 ? SAM9M11 [DATASHEET] 593 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.7.5 Slave Mode 31.7.5.1 Definition The Slave Mode is defined as a mode where the device receives the clock and the address from another device called the master. In this mode, the device never initiates and never completes the transmission (START, REPEATED_START and STOP conditions are always provided by the master). 31.7.5.2 Application Block Diagram Figure 31-24. Slave Mode Typical Application Block Diagram VDD R R Master TWD Host with TWI TWCK Interface Host with TWI Host with TWI LCD Controller Interface Interface Slave 1 Slave 2 Slave 3 31.7.5.3 Programming Slave Mode The following fields must be programmed before entering Slave mode: 1. SADR (TWI_SMR): The slave device address is used in order to be accessed by master devices in read or write mode. 2. MSDIS (TWI_CR): Disable the master mode. 3. SVEN (TWI_CR): Enable the slave mode. As the device receives the clock, values written in TWI_CWGR are not taken into account. 31.7.5.4 Receiving Data After a Start or Repeated Start condition is detected and if the address sent by the Master matches with the Slave address programmed in the SADR (Slave ADdress) field, SVACC (Slave ACCess) flag is set and SVREAD (Slave READ) indicates the direction of the transfer. SVACC remains high until a STOP condition or a repeated START is detected. When such a condition is detected, EOSACC (End Of Slave ACCess) flag is set. Read Sequence In the case of a Read sequence (SVREAD is high), TWI transfers data written in the TWI_THR (TWI Transmit Holding Register) until a STOP condition or a REPEATED_START + an address different from SADR is detected. Note that at the end of the read sequence TXCOMP (Transmission Complete) flag is set and SVACC reset. As soon as data is written in the TWI_THR, TXRDY (Transmit Holding Register Ready) flag is reset, and it is set when the shift register is empty and the sent data acknowledged or not. If the data is not acknowledged, the NACK flag is set. Note that a STOP or a repeated START always follows a NACK. See Figure 31-25 on page 595. 594 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Write Sequence In the case of a Write sequence (SVREAD is low), the RXRDY (Receive Holding Register Ready) flag is set as soon as a character has been received in the TWI_RHR (TWI Receive Holding Register). RXRDY is reset when reading the TWI_RHR. TWI continues receiving data until a STOP condition or a REPEATED_START + an address different from SADR is detected. Note that at the end of the write sequence TXCOMP flag is set and SVACC reset. See Figure 31-26 on page 596. Clock Synchronization Sequence In the case where TWI_THR or TWI_RHR is not written/read in time, TWI performs a clock synchronization. Clock stretching information is given by the SCLWS (Clock Wait state) bit. See Figure 31-28 on page 597 and Figure 31-29 on page 598. General Call In the case where a GENERAL CALL is performed, GACC (General Call ACCess) flag is set. After GACC is set, it is up to the programmer to interpret the meaning of the GENERAL CALL and to decode the new address programming sequence. See Figure 31-27 on page 596. 31.7.5.5 Data Transfer Read Operation The read mode is defined as a data requirement from the master. After a START or a REPEATED START condition is detected, the decoding of the address starts. If the slave address (SADR) is decoded, SVACC is set and SVREAD indicates the direction of the transfer. Until a STOP or REPEATED START condition is detected, TWI continues sending data loaded in the TWI_THR. If a STOP condition or a REPEATED START + an address different from SADR is detected, SVACC is reset. Figure 31-25 describes the write operation. Figure 31-25. Read Access Ordered by a MASTER SADR does not match, SADR matches, TWI answers with a NACK TWI answers with an ACK ACK/NACK from the Master TWD S ADR R NA DATA NA P/S/Sr SADR R A DATA A A DATA NA S/Sr TXRDY Write THR Read RHR NACK SVACC SVREAD SVREAD has to be taken into account only while SVACC is active EOSVACC Notes: 1. When SVACC is low, the state of SVREAD becomes irrelevant. 2. TXRDY is reset when data has been transmitted from TWI_THR to the shift register and set when this data has been acknowledged or non acknowledged. SAM9M11 [DATASHEET] 595 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Write Operation The write mode is defined as a data transmission from the master. After a START or a REPEATED START, the decoding of the address starts. If the slave address is decoded, SVACC is set and SVREAD indicates the direction of the transfer (SVREAD is low in this case). Until a STOP or REPEATED START condition is detected, TWI stores the received data in the TWI_RHR. If a STOP condition or a REPEATED START + an address different from SADR is detected, SVACC is reset. Figure 31-26 describes the Write operation. Figure 31-26. Write Access Ordered by a Master SADR does not match, SADR matches, TWI answers with a NACK TWI answers with an ACK Read RHR TWD S ADR W NA DATA NA P/S/Sr SADR W A DATA A A DATA NA S/Sr RXRDY SVACC SVREAD SVREAD has to be taken into account only while SVACC is active EOSVACC Notes: 1. When SVACC is low, the state of SVREAD becomes irrelevant. 2. RXRDY is set when data has been transmitted from the shift register to the TWI_RHR and reset when this data is read. General Call The general call is performed in order to change the address of the slave. If a GENERAL CALL is detected, GACC is set. After the detection of General Call, it is up to the programmer to decode the commands which come afterwards. In case of a WRITE command, the programmer has to decode the programming sequence and program a new SADR if the programming sequence matches. Figure 31-27 describes the General Call access. Figure 31-27. Master Performs a General Call RESET command = 00000110X 0000000 + W WRITE command = 00000100X TXD S GGEENNEERRAALL CCAALLLL A Reset or write DADD A DATA1 A DATA2 A New SADR A P New SADR Programming sequence GCACC Reset after read SVACC Note: This method allows the user to create an own programming sequence by choosing the programming bytes and the number of them. The programming sequence has to be provided to the master. Clock Synchronization In both read and write modes, it may happen that TWI_THR/TWI_RHR buffer is not filled /emptied before the emission/reception of a new character. In this case, to avoid sending/receiving undesired data, a clock stretching mechanism is implemented. 596 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Clock Synchronization in Read Mode The clock is tied low if the shift register is empty and if a STOP or REPEATED START condition was not detected. It is tied low until the shift register is loaded. Figure 31-28 describes the clock synchronization in Read mode. Figure 31-28. Clock Synchronization in Read Mode TWI_THR DDAATTAA00 1 DATA1 DATA2 SS SADR R A DATA0 A DATA1 A XXXXXXX DATA2 NA S 2 TWCK CLOCK is tied low by the TWI as long as THR is empty Write THR SCLWS TXRDY SVACC SVREAD As soon as a START is detected TXCOMP TWI_THR is transmitted to the shift register Ack or Nack from the master 1 The data is memorized in TWI_THR until a new value is written 2 The clock is stretched after the ACK, the state of TWD is undefined during clock stretching Notes: 1. TXRDY is reset when data has been written in the TWI_THR to the shift register and set when this data has been acknowledged or non acknowledged. 2. At the end of the read sequence, TXCOMP is set after a STOP or after a REPEATED_START + an address different from SADR. 3. SCLWS is automatically set when the clock synchronization mechanism is started. Clock Synchronization in Write Mode The clock is tied low if the shift register and the TWI_RHR is full. If a STOP or REPEATED_START condition was not detected, it is tied low until TWI_RHR is read. Figure 31-29 describes the clock synchronization in Read mode. SAM9M11 [DATASHEET] 597 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 31-29. Clock Synchronization in Write Mode TWCK CLOCK is tied low by the TWI as long as RHR is full TWD S SADR W A DATA0 A DATA1 A DATA2 NA S ADR TWI_RHR DATA0 is not read in the RHR DATA1 DATA2 SCLWS SCL is stretched on the last bit of DATA1 RXRDY Rd DATA0 Rd DATA1 Rd DATA2 SVACC SVREAD As soon as a START is detected TXCOMP Notes: 1. At the end of the read sequence, TXCOMP is set after a STOP or after a REPEATED_START + an address different from SADR. 2. SCLWS is automatically set when the clock synchronization mechanism is started and automatically reset when the mechanism is finished. Reversal after a Repeated Start Reversal of Read to Write The master initiates the communication by a read command and finishes it by a write command. Figure 31-30 describes the repeated start + reversal from Read to Write mode. Figure 31-30. Repeated Start + Reversal from Read to Write Mode TWI_THR DATA0 DATA1 TWD S SADR R A DATA0 A DATA1 NA Sr SADR W A DATA2 A DATA3 A P TWI_RHR DATA2 DATA3 SVACC SVREAD TXRDY RXRDY EOSACC Cleared after read TXCOMP As soon as a START is detected Note: 1. 1. TXCOMP is only set at the end of the transmission because after the repeated start, SADR is detected again. Reversal of Write to Read The master initiates the communication by a write command and finishes it by a read command. Figure 31-31 describes the repeated start + reversal from Write to Read mode. 598 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 31-31. Repeated Start + Reversal from Write to Read Mode TWI_THR DATA2 DATA3 TWD S SADR W A DATA0 A DATA1 A Sr SADR R A DATA2 A DATA3 NA P TWI_RHR DATA0 DATA1 SVACC SVREAD TXRDY RXRDY Read TWI_RHR EOSACC Cleared after read TXCOMP As soon as a START is detected Notes: 1. In this case, if TWI_THR has not been written at the end of the read command, the clock is automatically stretched before the ACK. 2. TXCOMP is only set at the end of the transmission because after the repeated start, SADR is detected again. 31.7.5.6 Read Write Flowcharts The flowchart shown in Figure 31-32 gives an example of read and write operations in Slave mode. A polling or interrupt method can be used to check the status bits. The interrupt method requires that the interrupt enable register (TWI_IER) be configured first. SAM9M11 [DATASHEET] 599 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 31-32. Read Write Flowchart in Slave Mode Set the SLAVE mode: SADR + MSDIS + SVEN Read Status Register No SVACC = 1 ? GACC = 1 ? No SVREAD = 0 ? No No EOSACC = 1 ? No TXRDY= 1 ? Write in TWI_THR No TXCOMP = 1 ? No RXRDY= 0 ? END Read TWI_RHR GENERAL CALL TREATMENT Decoding of the programming sequence Prog seq No OK ? Change SADR 600 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.8 Two-wire Interface (TWI) User Interface Table 31-6. Register Mapping Offset Register Name Access Reset 0x00 Control Register TWI_CR Write-only – 0x04 Master Mode Register TWI_MMR Read/Write 0x00000000 0x08 Slave Mode Register TWI_SMR Read/Write 0x00000000 0x0C Internal Address Register TWI_IADR Read/Write 0x00000000 0x10 Clock Waveform Generator Register TWI_CWGR Read/Write 0x00000000 0x20 Status Register TWI_SR Read-only 0x0000F009 0x24 Interrupt Enable Register TWI_IER Write-only – 0x28 Interrupt Disable Register TWI_IDR Write-only – 0x2C Interrupt Mask Register TWI_IMR Read-only 0x00000000 0x30 Receive Holding Register TWI_RHR Read-only 0x00000000 0x34 Transmit Holding Register TWI_THR Write-only – 0x38–0xFC Reserved – – – SAM9M11 [DATASHEET] 601 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.8.1 TWI Control Register Name: TWI_CR Address: 0xFFF84000 (0), 0xFFF88000 (1) Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 SWRST QUICK SVDIS SVEN MSDIS MSEN STOP START • START: Send a START Condition 0: No effect. 1: A frame beginning with a START bit is transmitted according to the features defined in the mode register. This action is necessary when the TWI peripheral wants to read data from a slave. When configured in Master Mode with a write operation, a frame is sent as soon as the user writes a character in the Transmit Holding Register (TWI_THR). • STOP: Send a STOP Condition 0: No effect. 1: STOP Condition is sent just after completing the current byte transmission in master read mode. – In single data byte master read, the START and STOP must both be set. – In multiple data bytes master read, the STOP must be set after the last data received but one. – In master read mode, if a NACK bit is received, the STOP is automatically performed. – In master data write operation, a STOP condition will be sent after the transmission of the current data is finished. • MSEN: TWI Master Mode Enabled 0: No effect. 1: If MSDIS = 0, the master mode is enabled. Note: Switching from Slave to Master mode is only permitted when TXCOMP = 1. • MSDIS: TWI Master Mode Disabled 0: No effect. 1: The master mode is disabled, all pending data is transmitted. The shifter and holding characters (if it contains data) are transmitted in case of write operation. In read operation, the character being transferred must be completely received before disabling. • SVEN: TWI Slave Mode Enabled 0: No effect. 1: If SVDIS = 0, the slave mode is enabled. Note: Switching from Master to Slave mode is only permitted when TXCOMP = 1. 602 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• SVDIS: TWI Slave Mode Disabled 0: No effect. 1: The slave mode is disabled. The shifter and holding characters (if it contains data) are transmitted in case of read oper- ation. In write operation, the character being transferred must be completely received before disabling. • QUICK: SMBUS Quick Command 0: No effect. 1: If Master mode is enabled, a SMBUS Quick Command is sent. • SWRST: Software Reset 0: No effect. 1: Equivalent to a system reset. SAM9M11 [DATASHEET] 603 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.8.2 TWI Master Mode Register Name: TWI_MMR Address: 0xFFF84004 (0), 0xFFF88004 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – DADR 15 14 13 12 11 10 9 8 – – – MREAD – – IADRSZ 7 6 5 4 3 2 1 0 – – – – – – – – • IADRSZ: Internal Device Address Size IADRSZ[9:8] Description 0 0 No internal device address 0 1 One-byte internal device address 1 0 Two-byte internal device address 1 1 Three-byte internal device address • MREAD: Master Read Direction 0: Master write direction. 1: Master read direction. • DADR: Device Address The device address is used to access slave devices in read or write mode. Those bits are only used in Master mode. 604 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.8.3 TWI Slave Mode Register Name: TWI_SMR Address: 0xFFF84008 (0), 0xFFF88008 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – SADR 15 14 13 12 11 10 9 8 – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – – • SADR: Slave Address The slave device address is used in Slave mode in order to be accessed by master devices in read or write mode. SADR must be programmed before enabling the Slave mode or after a general call. Writes at other times have no effect. SAM9M11 [DATASHEET] 605 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.8.4 TWI Internal Address Register Name: TWI_IADR Address: 0xFFF8400C (0), 0xFFF8800C (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 IADR 15 14 13 12 11 10 9 8 IADR 7 6 5 4 3 2 1 0 IADR • IADR: Internal Address 0, 1, 2 or 3 bytes depending on IADRSZ. 606 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.8.5 TWI Clock Waveform Generator Register Name: TWI_CWGR Address: 0xFFF84010 (0), 0xFFF88010 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – CKDIV 15 14 13 12 11 10 9 8 CHDIV 7 6 5 4 3 2 1 0 CLDIV TWI_CWGR is only used in Master mode. • CLDIV: Clock Low Divider The SCL low period is defined as follows: t = ((CLDIV×2CKDIV)+4)×t low MCK • CHDIV: Clock High Divider The SCL high period is defined as follows: t = ((CHDIV×2CKDIV)+4)×t high MCK • CKDIV: Clock Divider The CKDIV is used to increase both SCL high and low periods. SAM9M11 [DATASHEET] 607 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.8.6 TWI Status Register Name: TWI_SR Address: 0xFFF84020 (0), 0xFFF88020 (1) Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 EOSACC SCLWS ARBLST NACK 7 6 5 4 3 2 1 0 – OVRE GACC SVACC SVREAD TXRDY RXRDY TXCOMP • TXCOMP: Transmission Completed (automatically set / reset) TXCOMP used in Master mode: 0: During the length of the current frame. 1: When both holding and shifter registers are empty and STOP condition has been sent. TXCOMP behavior in Master mode can be seen in Figure 31-8 on page 581 and in Figure 31-10 on page 582. TXCOMP used in Slave mode: 0: As soon as a Start is detected. 1: After a Stop or a Repeated Start + an address different from SADR is detected. TXCOMP behavior in Slave mode can be seen in Figure 31-28 on page 597, Figure 31-29 on page 598, Figure 31-30 on page 598 and Figure 31-31 on page 599. • RXRDY: Receive Holding Register Ready (automatically set / reset) 0: No character has been received since the last TWI_RHR read operation. 1: A byte has been received in the TWI_RHR since the last read. RXRDY behavior in Master mode can be seen in Figure 31-10 on page 582. RXRDY behavior in Slave mode can be seen in Figure 31-26 on page 596, Figure 31-29 on page 598, Figure 31-30 on page 598 and Figure 31-31 on page 599. • TXRDY: Transmit Holding Register Ready (automatically set / reset) TXRDY used in Master mode: 0: The transmit holding register has not been transferred into shift register. Set to 0 when writing into TWI_THR. 1: As soon as a data byte is transferred from TWI_THR to internal shifter or if a NACK error is detected, TXRDY is set at the same time as TXCOMP and NACK. TXRDY is also set when MSEN is set (enable TWI). TXRDY behavior in Master mode can be seen in Figure 31-8 on page 581. TXRDY used in Slave mode: 0: As soon as data is written in the TWI_THR, until this data has been transmitted and acknowledged (ACK or NACK). 1: It indicates that the TWI_THR is empty and that data has been transmitted and acknowledged. 608 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

If TXRDY is high and if a NACK has been detected, the transmission will be stopped. Thus when TRDY = NACK = 1, the programmer must not fill TWI_THR to avoid losing it. TXRDY behavior in Slave mode can be seen in Figure 31-25 on page 595, Figure 31-28 on page 597, Figure 31-30 on page 598 and Figure 31-31 on page 599. • SVREAD: Slave Read (automatically set / reset) This bit is only used in Slave mode. When SVACC is low (no Slave access has been detected) SVREAD is irrelevant. 0: Indicates that a write access is performed by a Master. 1: Indicates that a read access is performed by a Master. SVREAD behavior can be seen in Figure 31-25 on page 595, Figure 31-26 on page 596, Figure 31-30 on page 598 and Figure 31-31 on page 599. • SVACC: Slave Access (automatically set / reset) This bit is only used in Slave mode. 0: TWI is not addressed. SVACC is automatically cleared after a NACK or a STOP condition is detected. 1: Indicates that the address decoding sequence has matched (A Master has sent SADR). SVACC remains high until a NACK or a STOP condition is detected. SVACC behavior can be seen in Figure 31-25 on page 595, Figure 31-26 on page 596, Figure 31-30 on page 598 and Fig- ure 31-31 on page 599. • GACC: General Call Access (clear on read) This bit is only used in Slave mode. 0: No General Call has been detected. 1: A General Call has been detected. After the detection of General Call, if need be, the programmer may acknowledge this access and decode the following bytes and respond according to the value of the bytes. GACC behavior can be seen in Figure 31-27 on page 596. • OVRE: Overrun Error (clear on read) This bit is only used in Master mode. 0: TWI_RHR has not been loaded while RXRDY was set 1: TWI_RHR has been loaded while RXRDY was set. Reset by read in TWI_SR when TXCOMP is set. • NACK: Not Acknowledged (clear on read) NACK used in Master mode: 0: Each data byte has been correctly received by the far-end side TWI slave component. 1: A data byte has not been acknowledged by the slave component. Set at the same time as TXCOMP. NACK used in Slave Read mode: 0: Each data byte has been correctly received by the Master. 1: In read mode, a data byte has not been acknowledged by the Master. When NACK is set the programmer must not fill TWI_THR even if TXRDY is set, because it means that the Master will stop the data transfer or re initiate it. Note that in Slave Write mode all data are acknowledged by the TWI. SAM9M11 [DATASHEET] 609 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• ARBLST: Arbitration Lost (clear on read) This bit is only used in Master mode. 0: Arbitration won. 1: Arbitration lost. Another master of the TWI bus has won the multi-master arbitration. TXCOMP is set at the same time. • SCLWS: Clock Wait State (automatically set / reset) This bit is only used in Slave mode. 0: The clock is not stretched. 1: The clock is stretched. TWI_THR / TWI_RHR buffer is not filled / emptied before the emission / reception of a new character. SCLWS behavior can be seen in Figure 31-28 on page 597 and Figure 31-29 on page 598. • EOSACC: End Of Slave Access (clear on read) This bit is only used in Slave mode. 0: A slave access is being performing. 1: The Slave Access is finished. End Of Slave Access is automatically set as soon as SVACC is reset. EOSACC behavior can be seen in Figure 31-30 on page 598 and Figure 31-31 on page 599 610 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.8.7 TWI Interrupt Enable Register Name: TWI_IER Address: 0xFFF84024 (0), 0xFFF88024 (1) Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 EOSACC SCL_WS ARBLST NACK 7 6 5 4 3 2 1 0 – OVRE GACC SVACC – TXRDY RXRDY TXCOMP • TXCOMP: Transmission Completed Interrupt Enable • RXRDY: Receive Holding Register Ready Interrupt Enable • TXRDY: Transmit Holding Register Ready Interrupt Enable • SVACC: Slave Access Interrupt Enable • GACC: General Call Access Interrupt Enable • OVRE: Overrun Error Interrupt Enable • NACK: Not Acknowledge Interrupt Enable • ARBLST: Arbitration Lost Interrupt Enable • SCL_WS: Clock Wait State Interrupt Enable • EOSACC: End Of Slave Access Interrupt Enable 0: No effect. 1: Enables the corresponding interrupt. SAM9M11 [DATASHEET] 611 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.8.8 TWI Interrupt Disable Register Name: TWI_IDR Address: 0xFFF84028 (0), 0xFFF88028 (1) Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 EOSACC SCL_WS ARBLST NACK 7 6 5 4 3 2 1 0 – OVRE GACC SVACC – TXRDY RXRDY TXCOMP • TXCOMP: Transmission Completed Interrupt Disable • RXRDY: Receive Holding Register Ready Interrupt Disable • TXRDY: Transmit Holding Register Ready Interrupt Disable • SVACC: Slave Access Interrupt Disable • GACC: General Call Access Interrupt Disable • OVRE: Overrun Error Interrupt Disable • NACK: Not Acknowledge Interrupt Disable • ARBLST: Arbitration Lost Interrupt Disable • SCL_WS: Clock Wait State Interrupt Disable • EOSACC: End Of Slave Access Interrupt Disable 0: No effect. 1: Disables the corresponding interrupt. 612 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.8.9 TWI Interrupt Mask Register Name: TWI_IMR Address: 0xFFF8402C (0), 0xFFF8802C (1) Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 EOSACC SCL_WS ARBLST NACK 7 6 5 4 3 2 1 0 – OVRE GACC SVACC – TXRDY RXRDY TXCOMP • TXCOMP: Transmission Completed Interrupt Mask • RXRDY: Receive Holding Register Ready Interrupt Mask • TXRDY: Transmit Holding Register Ready Interrupt Mask • SVACC: Slave Access Interrupt Mask • GACC: General Call Access Interrupt Mask • OVRE: Overrun Error Interrupt Mask • NACK: Not Acknowledge Interrupt Mask • ARBLST: Arbitration Lost Interrupt Mask • SCL_WS: Clock Wait State Interrupt Mask • EOSACC: End Of Slave Access Interrupt Mask 0: The corresponding interrupt is disabled. 1: The corresponding interrupt is enabled. SAM9M11 [DATASHEET] 613 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.8.10 TWI Receive Holding Register Name: TWI_RHR Address: 0xFFF84030 (0), 0xFFF88030 (1) Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 RXDATA • RXDATA: Master or Slave Receive Holding Data 614 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

31.8.11 TWI Transmit Holding Register Name: TWI_THR Address: 0xFFF84034 (0), 0xFFF88034 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 TXDATA • TXDATA: Master or Slave Transmit Holding Data SAM9M11 [DATASHEET] 615 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32. Synchronous Serial Controller (SSC) 32.1 Description The Atmel Synchronous Serial Controller (SSC) provides a synchronous communication link with external devices. It supports many serial synchronous communication protocols generally used in audio and telecom applications such as I2S, Short Frame Sync, Long Frame Sync, etc. The SSC contains an independent receiver and transmitter and a common clock divider. The receiver and the transmitter each interface with three signals: the TD/RD signal for data, the TK/RK signal for the clock and the TF/RF signal for the Frame Sync. The transfers can be programmed to start automatically or on different events detected on the Frame Sync signal. The SSC’s high-level of programmability and its two dedicated PDC channels of up to 32 bits permit a continuous high bit rate data transfer without processor intervention. The SSC’s high-level of programmability and its use of DMA permit a continuous high bit rate data transfer without processor intervention. Featuring connection to two PDC channels and connection to the DMA, the SSC permits interfacing with low processor overhead to the following:  Codecs in master or slave mode  DAC through dedicated serial interface, particularly I2S  Magnetic card reader 32.2 Embedded Characteristics  Provides serial synchronous communication links used in audio and telecom applications (with CODECs in Master or Slave Modes, I2S, TDM Buses, Magnetic Card Reader,...)  Contains an independent receiver and transmitter and a common clock divider  Offers a configurable frame sync and data length  Receiver and transmitter can be programmed to start automatically or on detection of different event on the frame sync signal  Receiver and transmitter include a data signal, a clock signal and a frame synchronization signal 616 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.3 Block Diagram Figure 32-1. Block Diagram (with PDC) System Bus APB Bridge PDC Peripheral Bus TF TK TD MCK PMC PIO SSC Interface RF RK Interrupt Control RD SSC Interrupt SAM9M11 [DATASHEET] 617 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 32-2. Block Diagram (with DMA) System Bus APB Bridge DMA Peripheral Bus TF TK TD MCK PMC PIO SSC Interface RF RK Interrupt Control RD SSC Interrupt 32.4 Application Block Diagram Figure 32-3. Application Block Diagram Power Interrupt Test OS or RTOS Driver Management Management Management SSC Time Slot Frame Serial AUDIO Codec Line Interface Management Management 618 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.5 Pin Name List Table 32-1. I/O Lines Description Pin Name Pin Description Type RF Receiver Frame Synchro Input/Output RK Receiver Clock Input/Output RD Receiver Data Input TF Transmitter Frame Synchro Input/Output TK Transmitter Clock Input/Output TD Transmitter Data Output 32.6 Product Dependencies 32.6.1 I/O Lines The pins used for interfacing the compliant external devices may be multiplexed with PIO lines. Before using the SSC receiver, the PIO controller must be configured to dedicate the SSC receiver I/O lines to the SSC peripheral mode. Before using the SSC transmitter, the PIO controller must be configured to dedicate the SSC transmitter I/O lines to the SSC peripheral mode. Table 32-2. I/O Lines Instance Signal I/O Line Peripheral SSC0 RD0 PD3 A SSC0 RF0 PD5 A SSC0 RK0 PD4 A SSC0 TD0 PD2 A SSC0 TF0 PD1 A SSC0 TK0 PD0 A SSC1 RD1 PD11 A SSC1 RF1 PD15 A SSC1 RK1 PD13 A SSC1 TD1 PD10 A SSC1 TF1 PD14 A SSC1 TK1 PD12 A 32.6.2 Power Management The SSC is not continuously clocked. The SSC interface may be clocked through the Power Management Controller (PMC), therefore the programmer must first configure the PMC to enable the SSC clock. SAM9M11 [DATASHEET] 619 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.6.3 Interrupt The SSC interface has an interrupt line connected to the Advanced Interrupt Controller (AIC). Handling interrupts requires programming the AIC before configuring the SSC. All SSC interrupts can be enabled/disabled configuring the SSC Interrupt mask register. Each pending and Table 32-3. Peripheral IDs Instance ID SSC0 16 SSC1 17 unmasked SSC interrupt will assert the SSC interrupt line. The SSC interrupt service routine can get the interrupt origin by reading the SSC interrupt status register. 620 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.7 Functional Description This chapter contains the functional description of the following: SSC Functional Block, Clock Management, Data format, Start, Transmitter, Receiver and Frame Sync. The receiver and transmitter operate separately. However, they can work synchronously by programming the receiver to use the transmit clock and/or to start a data transfer when transmission starts. Alternatively, this can be done by programming the transmitter to use the receive clock and/or to start a data transfer when reception starts. The transmitter and the receiver can be programmed to operate with the clock signals provided on either the TK or RK pins. This allows the SSC to support many slave-mode data transfers. The maximum clock speed allowed on the TK and RK pins is the master clock divided by 2. Figure 32-4. SSC Functional Block Diagram Transmitter Clock Output TK Controller TK Input MCK Clock Transmit Clock TX clock Frame Sync TF Divider Controller Controller RX clock TXEN RX Start Start TX Start Data TD TF Selector Transmit Shift Register Controller APB Transmit Holding Transmit Sync Register Holding Register User Interface Receiver Clock Output Controller RK RK Input Receive Clock RX Clock Frame Sync Controller Controller RF TX Clock RXEN RX Start TX Start Start Data RD RF Selector Controller Receive Shift Register RC0R Receive Holding Receive Sync Interrupt Control Register Holding Register AIC SAM9M11 [DATASHEET] 621 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.7.1 Clock Management The transmitter clock can be generated by:  an external clock received on the TK I/O pad  the receiver clock  the internal clock divider The receiver clock can be generated by:  an external clock received on the RK I/O pad  the transmitter clock  the internal clock divider Furthermore, the transmitter block can generate an external clock on the TK I/O pad, and the receiver block can generate an external clock on the RK I/O pad. This allows the SSC to support many Master and Slave Mode data transfers. 32.7.1.1 Clock Divider Figure 32-5. Divided Clock Block Diagram Clock Divider SSC_CMR MCK Divided Clock / 2 12-bit Counter The Master Clock divider is determined by the 12-bit field DIV counter and comparator (so its maximal value is 4095) in the Clock Mode Register SSC_CMR, allowing a Master Clock division by up to 8190. The Divided Clock is provided to both the Receiver and Transmitter. When this field is programmed to 0, the Clock Divider is not used and remains inactive. When DIV is set to a value equal to or greater than 1, the Divided Clock has a frequency of Master Clock divided by 2 times DIV. Each level of the Divided Clock has a duration of the Master Clock multiplied by DIV. This ensures a 50% duty cycle for the Divided Clock regardless of whether the DIV value is even or odd. Figure 32-6. Divided Clock Generation Master Clock Divided Clock DIV = 1 Divided Clock Frequency = MCK/2 Master Clock Divided Clock DIV = 3 Divided Clock Frequency = MCK/6 622 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.7.1.2 Transmitter Clock Management The transmitter clock is generated from the receiver clock or the divider clock or an external clock scanned on the TK I/O pad. The transmitter clock is selected by the CKS field in SSC_TCMR (Transmit Clock Mode Register). Transmit Clock can be inverted independently by the CKI bits in SSC_TCMR. The transmitter can also drive the TK I/O pad continuously or be limited to the actual data transfer. The clock output is configured by the SSC_TCMR. The Transmit Clock Inversion (CKI) bits have no effect on the clock outputs. Programming the TCMR to select TK pin (CKS field) and at the same time Continuous Transmit Clock (CKO field) might lead to unpredictable results. Figure 32-7. Transmitter Clock Management TK (pin) MUX Tri_state Clock Controller Output Receiver Clock Divider Clock CKO Data Transfer CKS MINUVX CTorin-strtoaltleer TCrlaoncskmitter CKI CKG SAM9M11 [DATASHEET] 623 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.7.1.3 Receiver Clock Management The receiver clock is generated from the transmitter clock or the divider clock or an external clock scanned on the RK I/O pad. The Receive Clock is selected by the CKS field in SSC_RCMR (Receive Clock Mode Register). Receive Clocks can be inverted independently by the CKI bits in SSC_RCMR. The receiver can also drive the RK I/O pad continuously or be limited to the actual data transfer. The clock output is configured by the SSC_RCMR. The Receive Clock Inversion (CKI) bits have no effect on the clock outputs. Programming the RCMR to select RK pin (CKS field) and at the same time Continuous Receive Clock (CKO field) can lead to unpredictable results. Figure 32-8. Receiver Clock Management RK (pin) MUX Tri-state Clock Controller Output Transmitter Clock Divider Clock CKO Data Transfer CKS INV Tri-state MUX Controller Receiver Clock CKI CKG 32.7.1.4 Serial Clock Ratio Considerations The Transmitter and the Receiver can be programmed to operate with the clock signals provided on either the TK or RK pins. This allows the SSC to support many slave-mode data transfers. In this case, the maximum clock speed allowed on the RK pin is: ̶ Master Clock divided by 2 if Receiver Frame Synchro is input ̶ Master Clock divided by 3 if Receiver Frame Synchro is output In addition, the maximum clock speed allowed on the TK pin is: ̶ Master Clock divided by 6 if Transmit Frame Synchro is input ̶ Master Clock divided by 2 if Transmit Frame Synchro is output 32.7.2 Transmitter Operations A transmitted frame is triggered by a start event and can be followed by synchronization data before data transmission. The start event is configured by setting the Transmit Clock Mode Register (SSC_TCMR). See “Start” on page 626. The frame synchronization is configured setting the Transmit Frame Mode Register (SSC_TFMR). See “Frame Sync” on page 628. To transmit data, the transmitter uses a shift register clocked by the transmitter clock signal and the start mode selected in the SSC_TCMR. Data is written by the application to the SSC_THR then transferred to the shift register according to the data format selected. 624 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

When both the SSC_THR and the transmit shift register are empty, the status flag TXEMPTY is set in SSC_SR. When the Transmit Holding register is transferred in the Transmit shift register, the status flag TXRDY is set in SSC_SR and additional data can be loaded in the holding register. Figure 32-9. Transmitter Block Diagram SSC_CRTXEN TXEN SSC_SRTXEN SSC_CRTXDIS SSC_TCMR.STTDLY SSC_TFMR.FSDEN SSC_RCMR.START SSC_TCMR.START SSC_TFMR.DATNB SSC_TFMR.DATDEF RXEN TXEN SSC_TFMR.MSBF TX Controller TX Start Start RX Start Start TX Start TD RF Selector Selector RC0R RF Transmit Shift Register SSC_TFMR.FSDEN SSC_TCMR.STTDLY != 0 0 1 Transmitter Clock SSC_TFMR.DATLEN SSC_THR SSC_TSHR SSC_TFMR.FSLEN TX Controller counter reached STTDLY 32.7.3 Receiver Operations A received frame is triggered by a start event and can be followed by synchronization data before data transmission. The start event is configured setting the Receive Clock Mode Register (SSC_RCMR). See “Start” on page 626. The frame synchronization is configured setting the Receive Frame Mode Register (SSC_RFMR). See “Frame Sync” on page 628. The receiver uses a shift register clocked by the receiver clock signal and the start mode selected in the SSC_RCMR. The data is transferred from the shift register depending on the data format selected. When the receiver shift register is full, the SSC transfers this data in the holding register, the status flag RXRDY is set in SSC_SR and the data can be read in the receiver holding register. If another transfer occurs before read of the RHR, the status flag OVERUN is set in SSC_SR and the receiver shift register is transferred in the RHR. SAM9M11 [DATASHEET] 625 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 32-10. Receiver Block Diagram SSC_CR.RXEN SSC_SR.RXEN SSC_CR.RXDIS SSC_TCMR.START SSC_RCMR.START SSC_RFMR.MSBF TXEN SSC_RFMR.DATNB RXEN RX Start Start RX Start RF Selector RF Start RX Controller Selector RC0R RD Receive Shift Register SSC_RCMR.STTDLY != 0 load SSC_RSHR load SSC_RHR Receiver Clock SSC_RFMR.FSLEN SSC_RFMR.DATLEN RX Controller counter reached STTDLY 32.7.4 Start The transmitter and receiver can both be programmed to start their operations when an event occurs, respectively in the Transmit Start Selection (START) field of SSC_TCMR and in the Receive Start Selection (START) field of SSC_RCMR. Under the following conditions the start event is independently programmable:  Continuous. In this case, the transmission starts as soon as a word is written in SSC_THR and the reception starts as soon as the Receiver is enabled.  Synchronously with the transmitter/receiver  On detection of a falling/rising edge on TF/RF  On detection of a low level/high level on TF/RF  On detection of a level change or an edge on TF/RF A start can be programmed in the same manner on either side of the Transmit/Receive Clock Register (RCMR/TCMR). Thus, the start could be on TF (Transmit) or RF (Receive). Moreover, the Receiver can start when data is detected in the bit stream with the Compare Functions. Detection on TF/RF input/output is done by the field FSOS of the Transmit/Receive Frame Mode Register (TFMR/RFMR). 626 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 32-11. Transmit Start Mode TK TF (Input) TD Start = Low Level on TF (Output) X BO B1 STTDLY Start = Falling Edge on TF TD X BO B1 (Output) STTDLY Start = High Level on TF TD X BO B1 (Output) STTDLY Start = Rising Edge on TF TD X BO B1 (Output) STTDLY TD Start = Level Change on TF (Output) X BO B1 BO B1 STTDLY TD Start = Any Edge on TF (Output) X BO B1 BO B1 STTDLY Figure 32-12. Receive Pulse/Edge Start Modes RK RF (Input) RD Start = Low Level on RF (Input) X BO B1 STTDLY Start = Falling Edge on RF RD X BO B1 (Input) STTDLY Start = High Level on RF RD X BO B1 (Input) STTDLY Start = Rising Edge on RF RD X BO B1 (Input) STTDLY RD Start = Level Change on RF (Input) X BO B1 BO B1 STTDLY RD Start = Any Edge on RF (Input) X BO B1 BO B1 STTDLY SAM9M11 [DATASHEET] 627 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.7.5 Frame Sync The Transmitter and Receiver Frame Sync pins, TF and RF, can be programmed to generate different kinds of frame synchronization signals. The Frame Sync Output Selection (FSOS) field in the Receive Frame Mode Register (SSC_RFMR) and in the Transmit Frame Mode Register (SSC_TFMR) are used to select the required waveform.  Programmable low or high levels during data transfer are supported.  Programmable high levels before the start of data transfers or toggling are also supported. If a pulse waveform is selected, the Frame Sync Length (FSLEN) field in SSC_RFMR and SSC_TFMR programs the length of the pulse, from 1 bit time up to 256 bit time. The periodicity of the Receive and Transmit Frame Sync pulse output can be programmed through the Period Divider Selection (PERIOD) field in SSC_RCMR and SSC_TCMR. 32.7.5.1 Frame Sync Data Frame Sync Data transmits or receives a specific tag during the Frame Sync signal. During the Frame Sync signal, the Receiver can sample the RD line and store the data in the Receive Sync Holding Register and the transmitter can transfer Transmit Sync Holding Register in the Shifter Register. The data length to be sampled/shifted out during the Frame Sync signal is programmed by the FSLEN field in SSC_RFMR/SSC_TFMR and has a maximum value of 16. Concerning the Receive Frame Sync Data operation, if the Frame Sync Length is equal to or lower than the delay between the start event and the actual data reception, the data sampling operation is performed in the Receive Sync Holding Register through the Receive Shift Register. The Transmit Frame Sync Operation is performed by the transmitter only if the bit Frame Sync Data Enable (FSDEN) in SSC_TFMR is set. If the Frame Sync length is equal to or lower than the delay between the start event and the actual data transmission, the normal transmission has priority and the data contained in the Transmit Sync Holding Register is transferred in the Transmit Register, then shifted out. 32.7.5.2 Frame Sync Edge Detection The Frame Sync Edge detection is programmed by the FSEDGE field in SSC_RFMR/SSC_TFMR. This sets the corresponding flags RXSYN/TXSYN in the SSC Status Register (SSC_SR) on frame synchro edge detection (signals RF/TF). 32.7.6 Receive Compare Modes Figure 32-13. Receive Compare Modes RK RD CMP0 CMP1 CMP2 CMP3 Ignored B0 B1 B2 (Input) Start FSLEN STDLY DATLEN Up to 16 Bits (4 in This Example) 32.7.6.1 Compare Functions Length of the comparison patterns (Compare 0, Compare 1) and thus the number of bits they are compared to is defined by FSLEN, but with a maximum value of 16 bits. Comparison is always done by comparing the last bits received with the comparison pattern. Compare 0 can be one start event of the Receiver. In this case, the receiver compares at each new sample the last bits received at the Compare 0 pattern contained in the Compare 0 628 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Register (SSC_RC0R). When this start event is selected, the user can program the Receiver to start a new data transfer either by writing a new Compare 0, or by receiving continuously until Compare 1 occurs. This selection is done with the bit (STOP) in SSC_RCMR. 32.7.7 Data Format The data framing format of both the transmitter and the receiver are programmable through the Transmitter Frame Mode Register (SSC_TFMR) and the Receiver Frame Mode Register (SSC_RFMR). In either case, the user can independently select:  the event that starts the data transfer (START)  the delay in number of bit periods between the start event and the first data bit (STTDLY)  the length of the data (DATLEN)  the number of data to be transferred for each start event (DATNB).  the length of synchronization transferred for each start event (FSLEN)  the bit sense: most or lowest significant bit first (MSBF) Additionally, the transmitter can be used to transfer synchronization and select the level driven on the TD pin while not in data transfer operation. This is done respectively by the Frame Sync Data Enable (FSDEN) and by the Data Default Value (DATDEF) bits in SSC_TFMR. Table 32-4. Data Frame Registers Transmitter Receiver Field Length Comment SSC_TFMR SSC_RFMR DATLEN Up to 32 Size of word SSC_TFMR SSC_RFMR DATNB Up to 16 Number of words transmitted in frame SSC_TFMR SSC_RFMR MSBF Most significant bit first SSC_TFMR SSC_RFMR FSLEN Up to 16 Size of Synchro data register SSC_TFMR DATDEF 0 or 1 Data default value ended SSC_TFMR FSDEN Enable send SSC_TSHR SSC_TCMR SSC_RCMR PERIOD Up to 512 Frame size SSC_TCMR SSC_RCMR STTDLY Up to 255 Size of transmit start delay SAM9M11 [DATASHEET] 629 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 32-14. Transmit and Receive Frame Format in Edge/Pulse Start Modes Start Start PERIOD TF/RF(1) FSLEN Sync Data Default Data Data Default Sync Data TD (If FSDEN = 1) From SSC_TSHR FromDATDEF From SSC_THR From SSC_THR FromDATDEF Default Data Data Default TD (If FSDEN = 0) From DATDEF From SSC_THR From SSC_THR From DATDEF RD Sync Data Ignored Data Data Ignored Sync Data To SSC_RSHR To SSC_RHR To SSC_RHR STTDLY DATLEN DATLEN DATNB Note: 1. Example of input on falling edge of TF/RF. Figure 32-15. Transmit Frame Format in Continuous Mode Start TD Data Data Default From SSC_THR From SSC_THR DATLEN DATLEN Start: 1. TXEMPTY set to 1 2. Write into the SSC_THR Note: 1. STTDLY is set to 0. In this example, SSC_THR is loaded twice. FSDEN value has no effect on the transmission. SyncData cannot be output in continuous mode. Figure 32-16. Receive Frame Format in Continuous Mode Start = Enable Receiver RD Data Data To SSC_RHR To SSC_RHR DATLEN DATLEN Note: 1. STTDLY is set to 0. 32.7.8 Loop Mode The receiver can be programmed to receive transmissions from the transmitter. This is done by setting the Loop Mode (LOOP) bit in SSC_RFMR. In this case, RD is connected to TD, RF is connected to TF and RK is connected to TK. 630 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.7.9 Interrupt Most bits in SSC_SR have a corresponding bit in interrupt management registers. The SSC can be programmed to generate an interrupt when it detects an event. The interrupt is controlled by writing SSC_IER (Interrupt Enable Register) and SSC_IDR (Interrupt Disable Register) These registers enable and disable, respectively, the corresponding interrupt by setting and clearing the corresponding bit in SSC_IMR (Interrupt Mask Register), which controls the generation of interrupts by asserting the SSC interrupt line connected to the AIC. Figure 32-17. Interrupt Block Diagram (with PDC) SSC_IMR SSC_IER SSC_IDR PDC Set Clear TXBUFE ENDTX Transmitter TXRDY TXEMPTY TXSYNC SSC Interrupt Interrupt RXBUFF Control ENDRX Receiver RXRDY OVRUN RXSYNC Figure 32-18. Interrupt Block Diagram (with DMA) SSC_IMR SSC_IER SSC_IDR Set Clear Transmitter TXRDY TXEMPTY TXSYNC SSC Interrupt Interrupt Control Receiver RXRDY OVRUN RXSYNC SAM9M11 [DATASHEET] 631 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.8 SSC Application Examples The SSC can support several serial communication modes used in audio or high speed serial links. Some standard applications are shown in the following figures. All serial link applications supported by the SSC are not listed here. Figure 32-19. Audio Application Block Diagram Clock SCK TK Word Select WS I2S TF RECEIVER Data SD TD SSC RD Clock SCK RF Word Select WS RK Data SD MSB LSB MSB Left Channel Right Channel Figure 32-20. Codec Application Block Diagram Serial Data Clock (SCLK) TK Frame sync (FSYNC) TF CODEC Serial Data Out TD SSC Serial Data In RD RF Serial Data Clock (SCLK) RK Frame sync (FSYNC) First Time Slot Dstart Dend Serial Data Out Serial Data In 632 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 32-21. Time Slot Application Block Diagram SCLK TK FSYNC TF CODEC First Data Out Time Slot TD SSC Data in RD RF RK CODEC Second Time Slot Serial Data Clock (SCLK) Frame sync (FSYNC) First Time Slot Second Time Slot Dstart Dend Serial Data Out Serial Data in SAM9M11 [DATASHEET] 633 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9 Synchronous Serial Controller (SSC) User Interface Table 32-5. Register Mapping Offset Register Name Access Reset 0x0 Control Register SSC_CR Write-only – 0x4 Clock Mode Register SSC_CMR Read/Write 0x0 0x8 Reserved – – – 0xC Reserved – – – 0x10 Receive Clock Mode Register SSC_RCMR Read/Write 0x0 0x14 Receive Frame Mode Register SSC_RFMR Read/Write 0x0 0x18 Transmit Clock Mode Register SSC_TCMR Read/Write 0x0 0x1C Transmit Frame Mode Register SSC_TFMR Read/Write 0x0 0x20 Receive Holding Register SSC_RHR Read-only 0x0 0x24 Transmit Holding Register SSC_THR Write-only – 0x28 Reserved – – – 0x2C Reserved – – – 0x30 Receive Sync. Holding Register SSC_RSHR Read-only 0x0 0x34 Transmit Sync. Holding Register SSC_TSHR Read/Write 0x0 0x38 Receive Compare 0 Register SSC_RC0R Read/Write 0x0 0x3C Receive Compare 1 Register SSC_RC1R Read/Write 0x0 0x40 Status Register SSC_SR Read-only 0x000000CC 0x44 Interrupt Enable Register SSC_IER Write-only – 0x48 Interrupt Disable Register SSC_IDR Write-only – 0x4C Interrupt Mask Register SSC_IMR Read-only 0x0 0x50–0xFC Reserved – – – 0x100–0x124 Reserved for Peripheral Data Controller (PDC) – – – 634 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9.1 SSC Control Register Name: SSC_CR: Address: 0xFFF9C000 (0), 0xFFFA0000 (1) Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 SWRST – – – – – TXDIS TXEN 7 6 5 4 3 2 1 0 – – – – – – RXDIS RXEN • RXEN: Receive Enable 0: No effect. 1: Enables Receive if RXDIS is not set. • RXDIS: Receive Disable 0: No effect. 1: Disables Receive. If a character is currently being received, disables at end of current character reception. • TXEN: Transmit Enable 0: No effect. 1: Enables Transmit if TXDIS is not set. • TXDIS: Transmit Disable 0: No effect. 1: Disables Transmit. If a character is currently being transmitted, disables at end of current character transmission. • SWRST: Software Reset 0: No effect. 1: Performs a software reset. Has priority on any other bit in SSC_CR. SAM9M11 [DATASHEET] 635 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9.2 SSC Clock Mode Register Name: SSC_CMR Address: 0xFFF9C004 (0), 0xFFFA0004 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – DIV 7 6 5 4 3 2 1 0 DIV • DIV: Clock Divider 0: The Clock Divider is not active. Any Other Value: The Divided Clock equals the Master Clock divided by 2 times DIV. The maximum bit rate is MCK/2. The minimum bit rate is MCK/2 x 4095 = MCK/8190. 636 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9.3 SSC Receive Clock Mode Register Name: SSC_RCMR Address: 0xFFF9C010 (0), 0xFFFA0010 (1) Access: Read/Write 31 30 29 28 27 26 25 24 PERIOD 23 22 21 20 19 18 17 16 STTDLY 15 14 13 12 11 10 9 8 – – – STOP START 7 6 5 4 3 2 1 0 CKG CKI CKO CKS • CKS: Receive Clock Selection CKS Selected Receive Clock 0x0 Divided Clock 0x1 TK Clock signal 0x2 RK pin 0x3 Reserved • CKO: Receive Clock Output Mode Selection CKO Receive Clock Output Mode RK pin 0x0 None Input-only 0x1 Continuous Receive Clock Output 0x2 Receive Clock only during data transfers Output 0x3–0x7 Reserved • CKI: Receive Clock Inversion 0: The data inputs (Data and Frame Sync signals) are sampled on Receive Clock falling edge. The Frame Sync signal out- put is shifted out on Receive Clock rising edge. 1: The data inputs (Data and Frame Sync signals) are sampled on Receive Clock rising edge. The Frame Sync signal out- put is shifted out on Receive Clock falling edge. CKI affects only the Receive Clock and not the output clock signal. • CKG: Receive Clock Gating Selection CKG Receive Clock Gating 0x0 None, continuous clock 0x1 Receive Clock enabled only if RF Low 0x2 Receive Clock enabled only if RF High 0x3 Reserved SAM9M11 [DATASHEET] 637 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• START: Receive Start Selection START Receive Start 0x0 Continuous, as soon as the receiver is enabled, and immediately after the end of transfer of the previous data. 0x1 Transmit start 0x2 Detection of a low level on RF signal 0x3 Detection of a high level on RF signal 0x4 Detection of a falling edge on RF signal 0x5 Detection of a rising edge on RF signal 0x6 Detection of any level change on RF signal 0x7 Detection of any edge on RF signal 0x8 Compare 0 0x9–0xF Reserved • STOP: Receive Stop Selection 0: After completion of a data transfer when starting with a Compare 0, the receiver stops the data transfer and waits for a new compare 0. 1: After starting a receive with a Compare 0, the receiver operates in a continuous mode until a Compare 1 is detected. • STTDLY: Receive Start Delay If STTDLY is not 0, a delay of STTDLY clock cycles is inserted between the start event and the actual start of reception. When the Receiver is programmed to start synchronously with the Transmitter, the delay is also applied. Note: It is very important that STTDLY be set carefully. If STTDLY must be set, it should be done in relation to TAG (Receive Sync Data) reception. • PERIOD: Receive Period Divider Selection This field selects the divider to apply to the selected Receive Clock in order to generate a new Frame Sync Signal. If 0, no PERIOD signal is generated. If not 0, a PERIOD signal is generated each 2 x (PERIOD+1) Receive Clock. 638 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9.4 SSC Receive Frame Mode Register Name: SSC_RFMR Address: 0xFFF9C014 (0), 0xFFFA0014 (1) Access: Read/Write 31 30 29 28 27 26 25 24 FSLEN_EXT FSLEN_EXT FSLEN_EXT FSLEN_EXT – – – FSEDGE 23 22 21 20 19 18 17 16 – FSOS FSLEN 15 14 13 12 11 10 9 8 – – – – DATNB 7 6 5 4 3 2 1 0 MSBF – LOOP DATLEN • DATLEN: Data Length 0: Forbidden value (1-bit data length not supported). Any other value: The bit stream contains DATLEN + 1 data bits. Moreover, it defines the transfer size performed by the PDC assigned to the Receiver. If DATLEN is lower or equal to 7, data transfers are in bytes. If DATLEN is between 8 and 15 (included), half-words are transferred, and for any other value, 32-bit words are transferred. • LOOP: Loop Mode 0: Normal operating mode. 1: RD is driven by TD, RF is driven by TF and TK drives RK. • MSBF: Most Significant Bit First 0: The lowest significant bit of the data register is sampled first in the bit stream. 1: The most significant bit of the data register is sampled first in the bit stream. • DATNB: Data Number per Frame This field defines the number of data words to be received after each transfer start, which is equal to (DATNB + 1). • FSLEN: Receive Frame Sync Length This field defines the number of bits sampled and stored in the Receive Sync Data Register. When this mode is selected by the START field in the Receive Clock Mode Register, it also determines the length of the sampled data to be compared to the Compare 0 or Compare 1 register. This field is used with FSLEN_EXT to determine the pulse length of the Receive Frame Sync signal. Pulse length is equal to FSLEN + (FSLEN_EXT * 16) + 1 Receive Clock periods. SAM9M11 [DATASHEET] 639 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• FSOS: Receive Frame Sync Output Selection FSOS Selected Receive Frame Sync Signal RF Pin 0x0 None Input-only 0x1 Negative Pulse Output 0x2 Positive Pulse Output 0x3 Driven Low during data transfer Output 0x4 Driven High during data transfer Output 0x5 Toggling at each start of data transfer Output 0x6–0x7 Reserved Undefined • FSEDGE: Frame Sync Edge Detection Determines which edge on Frame Sync will generate the interrupt RXSYN in the SSC Status Register. FSEDGE Frame Sync Edge Detection 0x0 Positive Edge Detection 0x1 Negative Edge Detection • FSLEN_EXT: FSLEN Field Extension Extends FSLEN field. For details, refer to FSLEN bit description on page 639. 640 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9.5 SSC Transmit Clock Mode Register Name: SSC_TCMR Address: 0xFFF9C018 (0), 0xFFFA0018 (1) Access: Read/Write 31 30 29 28 27 26 25 24 PERIOD 23 22 21 20 19 18 17 16 STTDLY 15 14 13 12 11 10 9 8 – – – – START 7 6 5 4 3 2 1 0 CKG CKI CKO CKS • CKS: Transmit Clock Selection CKS Selected Transmit Clock 0x0 Divided Clock 0x1 RK Clock signal 0x2 TK Pin 0x3 Reserved • CKO: Transmit Clock Output Mode Selection CKO Transmit Clock Output Mode TK pin 0x0 None Input-only 0x1 Continuous Transmit Clock Output 0x2 Transmit Clock only during data transfers Output 0x3–0x7 Reserved • CKI: Transmit Clock Inversion 0: The data outputs (Data and Frame Sync signals) are shifted out on Transmit Clock falling edge. The Frame sync signal input is sampled on Transmit clock rising edge. 1: The data outputs (Data and Frame Sync signals) are shifted out on Transmit Clock rising edge. The Frame sync signal input is sampled on Transmit clock falling edge. CKI affects only the Transmit Clock and not the output clock signal. • CKG: Transmit Clock Gating Selection CKG Transmit Clock Gating 0x0 None, continuous clock 0x1 Transmit Clock enabled only if TF Low 0x2 Transmit Clock enabled only if TF High 0x3 Reserved SAM9M11 [DATASHEET] 641 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• START: Transmit Start Selection START Transmit Start Continuous, as soon as a word is written in the SSC_THR Register (if Transmit is enabled), and 0x0 immediately after the end of transfer of the previous data. 0x1 Receive start 0x2 Detection of a low level on TF signal 0x3 Detection of a high level on TF signal 0x4 Detection of a falling edge on TF signal 0x5 Detection of a rising edge on TF signal 0x6 Detection of any level change on TF signal 0x7 Detection of any edge on TF signal 0x8–0xF Reserved • STTDLY: Transmit Start Delay If STTDLY is not 0, a delay of STTDLY clock cycles is inserted between the start event and the actual start of transmission of data. When the Transmitter is programmed to start synchronously with the Receiver, the delay is also applied. Note: STTDLY must be set carefully. If STTDLY is too short in respect to TAG (Transmit Sync Data) emission, data is emit- ted instead of the end of TAG. • PERIOD: Transmit Period Divider Selection This field selects the divider to apply to the selected Transmit Clock to generate a new Frame Sync Signal. If 0, no period signal is generated. If not 0, a period signal is generated at each 2 x (PERIOD+1) Transmit Clock. 642 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9.6 SSC Transmit Frame Mode Register Name: SSC_TFMR Address: 0xFFF9C01C (0), 0xFFFA001C (1) Access: Read/Write 31 30 29 28 27 26 25 24 FSLEN_EXT FSLEN_EXT FSLEN_EXT FSLEN_EXT – – – FSEDGE 23 22 21 20 19 18 17 16 FSDEN FSOS FSLEN 15 14 13 12 11 10 9 8 – – – – DATNB 7 6 5 4 3 2 1 0 MSBF – DATDEF DATLEN • DATLEN: Data Length 0: Forbidden value (1-bit data length not supported). Any other value: The bit stream contains DATLEN + 1 data bits. Moreover, it defines the transfer size performed by the PDC assigned to the Transmit. If DATLEN is lower or equal to 7, data transfers are bytes, if DATLEN is between 8 and 15 (included), half-words are transferred, and for any other value, 32-bit words are transferred. • DATDEF: Data Default Value This bit defines the level driven on the TD pin while out of transmission. Note that if the pin is defined as multi-drive by the PIO Controller, the pin is enabled only if the SCC TD output is 1. • MSBF: Most Significant Bit First 0: The lowest significant bit of the data register is shifted out first in the bit stream. 1: The most significant bit of the data register is shifted out first in the bit stream. • DATNB: Data Number per frame This field defines the number of data words to be transferred after each transfer start, which is equal to (DATNB +1). • FSLEN: Transmit Frame Sync Length This field defines the length of the Transmit Frame Sync signal and the number of bits shifted out from the Transmit Sync Data Register if FSDEN is 1. This field is used with FSLEN_EXT to determine the pulse length of the Transmit Frame Sync signal. Pulse length is equal to FSLEN + (FSLEN_EXT * 16) + 1 Transmit Clock period. SAM9M11 [DATASHEET] 643 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• FSOS: Transmit Frame Sync Output Selection FSOS Selected Transmit Frame Sync Signal TF Pin 0x0 None Input-only 0x1 Negative Pulse Output 0x2 Positive Pulse Output 0x3 Driven Low during data transfer Output 0x4 Driven High during data transfer Output 0x5 Toggling at each start of data transfer Output 0x6–0x7 Reserved Undefined • FSDEN: Frame Sync Data Enable 0: The TD line is driven with the default value during the Transmit Frame Sync signal. 1: SSC_TSHR value is shifted out during the transmission of the Transmit Frame Sync signal. • FSEDGE: Frame Sync Edge Detection Determines which edge on frame sync will generate the interrupt TXSYN (Status Register). FSEDGE Frame Sync Edge Detection 0x0 Positive Edge Detection 0x1 Negative Edge Detection • FSLEN_EXT: FSLEN Field Extension Extends FSLEN field. For details, refer to FSLEN bit description on page 643. 644 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9.7 SSC Receive Holding Register Name: SSC_RHR Address: 0xFFF9C020 (0), 0xFFFA0020 (1) Access: Read-only 31 30 29 28 27 26 25 24 RDAT 23 22 21 20 19 18 17 16 RDAT 15 14 13 12 11 10 9 8 RDAT 7 6 5 4 3 2 1 0 RDAT • RDAT: Receive Data Right aligned regardless of the number of data bits defined by DATLEN in SSC_RFMR. SAM9M11 [DATASHEET] 645 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9.8 SSC Transmit Holding Register Name: SSC_THR Address: 0xFFF9C024 (0), 0xFFFA0024 (1) Access: Write-only 31 30 29 28 27 26 25 24 TDAT 23 22 21 20 19 18 17 16 TDAT 15 14 13 12 11 10 9 8 TDAT 7 6 5 4 3 2 1 0 TDAT • TDAT: Transmit Data Right aligned regardless of the number of data bits defined by DATLEN in SSC_TFMR. 646 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9.9 SSC Receive Synchronization Holding Register Name: SSC_RSHR Address: 0xFFF9C030 (0), 0xFFFA0030 (1) Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 RSDAT 7 6 5 4 3 2 1 0 RSDAT • RSDAT: Receive Synchronization Data SAM9M11 [DATASHEET] 647 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9.10SSC Transmit Synchronization Holding Register Name: SSC_TSHR Address: 0xFFF9C034 (0), 0xFFFA0034 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 TSDAT 7 6 5 4 3 2 1 0 TSDAT • TSDAT: Transmit Synchronization Data 648 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9.11 SSC Receive Compare 0 Register Name: SSC_RC0R Address: 0xFFF9C038 (0), 0xFFFA0038 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 CP0 7 6 5 4 3 2 1 0 CP0 • CP0: Receive Compare Data 0 SAM9M11 [DATASHEET] 649 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9.12SSC Receive Compare 1 Register Name: SSC_RC1R Address: 0xFFF9C03C (0), 0xFFFA003C (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 CP1 7 6 5 4 3 2 1 0 CP1 • CP1: Receive Compare Data 1 650 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9.13SSC Status Register Name: SSC_SR Address: 0xFFF9C040 (0), 0xFFFA0040 (1) Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – RXEN TXEN 15 14 13 12 11 10 9 8 – – – – RXSYN TXSYN CP1 CP0 7 6 5 4 3 2 1 0 RXBUFF ENDRX OVRUN RXRDY TXBUFE ENDTX TXEMPTY TXRDY • TXRDY: Transmit Ready 0: Data has been loaded in SSC_THR and is waiting to be loaded in the Transmit Shift Register (TSR). 1: SSC_THR is empty. • TXEMPTY: Transmit Empty 0: Data remains in SSC_THR or is currently transmitted from TSR. 1: Last data written in SSC_THR has been loaded in TSR and last data loaded in TSR has been transmitted. • ENDTX: End of Transmission 0: The register SSC_TCR has not reached 0 since the last write in SSC_TCR or SSC_TNCR. 1: The register SSC_TCR has reached 0 since the last write in SSC_TCR or SSC_TNCR. • TXBUFE: Transmit Buffer Empty 0: SSC_TCR or SSC_TNCR have a value other than 0. 1: Both SSC_TCR and SSC_TNCR have a value of 0. • RXRDY: Receive Ready 0: SSC_RHR is empty. 1: Data has been received and loaded in SSC_RHR. • OVRUN: Receive Overrun 0: No data has been loaded in SSC_RHR while previous data has not been read since the last read of the Status Register. 1: Data has been loaded in SSC_RHR while previous data has not yet been read since the last read of the Status Register. • ENDRX: End of Reception 0: Data is written on the Receive Counter Register or Receive Next Counter Register. 1: End of PDCDMAC transfer when Receive Counter Register has arrived at zero. SAM9M11 [DATASHEET] 651 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• RXBUFF: Receive Buffer Full 0: SSC_RCR or SSC_RNCR have a value other than 0. 1: Both SSC_RCR and SSC_RNCR have a value of 0. • CP0: Compare 0 0: A compare 0 has not occurred since the last read of the Status Register. 1: A compare 0 has occurred since the last read of the Status Register. • CP1: Compare 1 0: A compare 1 has not occurred since the last read of the Status Register. 1: A compare 1 has occurred since the last read of the Status Register. • TXSYN: Transmit Sync 0: A Tx Sync has not occurred since the last read of the Status Register. 1: A Tx Sync has occurred since the last read of the Status Register. • RXSYN: Receive Sync 0: An Rx Sync has not occurred since the last read of the Status Register. 1: An Rx Sync has occurred since the last read of the Status Register. • TXEN: Transmit Enable 0: Transmit is disabled. 1: Transmit is enabled. • RXEN: Receive Enable 0: Receive is disabled. 1: Receive is enabled. 652 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9.14SSC Interrupt Enable Register Name: SSC_IER Address: 0xFFF9C044 (0), 0xFFFA0044 (1) Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – RXSYN TXSYN CP1 CP0 7 6 5 4 3 2 1 0 RXBUFF ENDRX OVRUN RXRDY TXBUFE ENDTX TXEMPTY TXRDY • TXRDY: Transmit Ready Interrupt Enable 0: No effect. 1: Enables the Transmit Ready Interrupt. • TXEMPTY: Transmit Empty Interrupt Enable 0: No effect. 1: Enables the Transmit Empty Interrupt. • ENDTX: End of Transmission Interrupt Enable 0: No effect. 1: Enables the End of Transmission Interrupt. • TXBUFE: Transmit Buffer Empty Interrupt Enable 0: No effect. 1: Enables the Transmit Buffer Empty Interrupt • RXRDY: Receive Ready Interrupt Enable 0: No effect. 1: Enables the Receive Ready Interrupt. • OVRUN: Receive Overrun Interrupt Enable 0: No effect. 1: Enables the Receive Overrun Interrupt. • ENDRX: End of Reception Interrupt Enable 0: No effect. 1: Enables the End of Reception Interrupt. SAM9M11 [DATASHEET] 653 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• RXBUFF: Receive Buffer Full Interrupt Enable 0: No effect. 1: Enables the Receive Buffer Full Interrupt. • CP0: Compare 0 Interrupt Enable 0: No effect. 1: Enables the Compare 0 Interrupt. • CP1: Compare 1 Interrupt Enable 0: No effect. 1: Enables the Compare 1 Interrupt. • TXSYN: Tx Sync Interrupt Enable 0: No effect. 1: Enables the Tx Sync Interrupt. • RXSYN: Rx Sync Interrupt Enable 0: No effect. 1: Enables the Rx Sync Interrupt. 654 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9.15SSC Interrupt Disable Register Name: SSC_IDR Address: 0xFFF9C048 (0), 0xFFFA0048 (1) Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – RXSYN TXSYN CP1 CP0 7 6 5 4 3 2 1 0 RXBUFF ENDRX OVRUN RXRDY TXBUFE ENDTX TXEMPTY TXRDY • TXRDY: Transmit Ready Interrupt Disable 0: No effect. 1: Disables the Transmit Ready Interrupt. • TXEMPTY: Transmit Empty Interrupt Disable 0: No effect. 1: Disables the Transmit Empty Interrupt. • ENDTX: End of Transmission Interrupt Disable 0: No effect. 1: Disables the End of Transmission Interrupt. • TXBUFE: Transmit Buffer Empty Interrupt Disable 0: No effect. 1: Disables the Transmit Buffer Empty Interrupt. • RXRDY: Receive Ready Interrupt Disable 0: No effect. 1: Disables the Receive Ready Interrupt. • OVRUN: Receive Overrun Interrupt Disable 0: No effect. 1: Disables the Receive Overrun Interrupt. • ENDRX: End of Reception Interrupt Disable 0: No effect. 1: Disables the End of Reception Interrupt. SAM9M11 [DATASHEET] 655 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• RXBUFF: Receive Buffer Full Interrupt Disable 0: No effect. 1: Disables the Receive Buffer Full Interrupt. • CP0: Compare 0 Interrupt Disable 0: No effect. 1: Disables the Compare 0 Interrupt. • CP1: Compare 1 Interrupt Disable 0: No effect. 1: Disables the Compare 1 Interrupt. • TXSYN: Tx Sync Interrupt Enable 0: No effect. 1: Disables the Tx Sync Interrupt. • RXSYN: Rx Sync Interrupt Enable 0: No effect. 1: Disables the Rx Sync Interrupt. 656 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

32.9.16SSC Interrupt Mask Register Name: SSC_IMR Address: 0xFFF9C04C (0), 0xFFFA004C (1) Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – RXSYN TXSYN CP1 CP0 7 6 5 4 3 2 1 0 RXBUFF ENDRX OVRUN RXRDY TXBUFE ENDTX TXEMPTY TXRDY • TXRDY: Transmit Ready Interrupt Mask 0: The Transmit Ready Interrupt is disabled. 1: The Transmit Ready Interrupt is enabled. • TXEMPTY: Transmit Empty Interrupt Mask 0: The Transmit Empty Interrupt is disabled. 1: The Transmit Empty Interrupt is enabled. • ENDTX: End of Transmission Interrupt Mask 0: The End of Transmission Interrupt is disabled. 1: The End of Transmission Interrupt is enabled. • TXBUFE: Transmit Buffer Empty Interrupt Mask 0: The Transmit Buffer Empty Interrupt is disabled. 1: The Transmit Buffer Empty Interrupt is enabled. • RXRDY: Receive Ready Interrupt Mask 0: The Receive Ready Interrupt is disabled. 1: The Receive Ready Interrupt is enabled. • OVRUN: Receive Overrun Interrupt Mask 0: The Receive Overrun Interrupt is disabled. 1: The Receive Overrun Interrupt is enabled. • ENDRX: End of Reception Interrupt Mask 0: The End of Reception Interrupt is disabled. 1: The End of Reception Interrupt is enabled. SAM9M11 [DATASHEET] 657 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• RXBUFF: Receive Buffer Full Interrupt Mask 0: The Receive Buffer Full Interrupt is disabled. 1: The Receive Buffer Full Interrupt is enabled. • CP0: Compare 0 Interrupt Mask 0: The Compare 0 Interrupt is disabled. 1: The Compare 0 Interrupt is enabled. • CP1: Compare 1 Interrupt Mask 0: The Compare 1 Interrupt is disabled. 1: The Compare 1 Interrupt is enabled. • TXSYN: Tx Sync Interrupt Mask 0: The Tx Sync Interrupt is disabled. 1: The Tx Sync Interrupt is enabled. • RXSYN: Rx Sync Interrupt Mask 0: The Rx Sync Interrupt is disabled. 1: The Rx Sync Interrupt is enabled. 658 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33. Timer Counter (TC) 33.1 Description The Timer Counter (TC) includes three identical 16-bit Timer Counter channels. Each channel can be independently programmed to perform a wide range of functions including frequency measurement, event counting, interval measurement, pulse generation, delay timing and pulse width modulation. Each channel has three external clock inputs, five internal clock inputs and two multi-purpose input/output signals which can be configured by the user. Each channel drives an internal interrupt signal which can be programmed to generate processor interrupts. The Timer Counter block has two global registers which act upon all three TC channels. The Block Control Register allows the three channels to be started simultaneously with the same instruction. The Block Mode Register defines the external clock inputs for each channel, allowing them to be chained. Table 33-1 gives the assignment of the device Timer Counter clock inputs common to Timer Counter 0 to 2. Table 33-1. Timer Counter Clock Assignment Name Definition TIMER_CLOCK1 MCK/2 TIMER_CLOCK2 MCK/8 TIMER_CLOCK3 MCK/32 TIMER_CLOCK4 MCK/128 TIMER_CLOCK5(1) SLCK Note: 1. When Slow Clock is selected for Master Clock (CSS = 0 in PMC Master CLock Register), TIMER_CLOCK5 input is Master Clock, i.e., Slow CLock modified by PRES and MDIV fields. 33.2 Embedded Characteristics  Three 16-bit Timer Counter Channels  Wide range of functions including: ̶ Frequency Measurement ̶ Event Counting ̶ Interval Measurement ̶ Pulse Generation ̶ Delay Timing ̶ Pulse Width Modulation ̶ Up/down Capabilities  Each channel is user-configurable and contains: ̶ Three external clock inputs ̶ Five internal clock inputs ̶ Two multi-purpose input/output signals  Two global registers that act on all three TC Channels SAM9M11 [DATASHEET] 659 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.3 Block Diagram Figure 33-1. Timer Counter Block Diagram Parallel I/O TIMER_CLOCK1 Controller TCLK0 TCLK0 TIMER_CLOCK2 TCLK1 TIOA1 TCLK2 TIMER_CLOCK3 TIOA2 XC0 Timer/Counter TCLK1 XC1 Channel 0 TIOA TIOA0 TIOA0 TIMER_CLOCK4 TIOB TIOB0 TCLK2 XC2 TIOB0 TIMER_CLOCK5 TC0XC0S SYNC INT0 TCLK0 TCLK1 XC0 Timer/Counter TIOA0 XC1 Channel 1 TIOA TIOA1 TIOA1 TIOB TIOB1 TIOA2 XC2 TIOB1 TCLK2 TC1XC1S SYNC INT1 TCLK0 XC0 Timer/Counter TCLK1 XC1 Channel 2 TIOA TIOA2 TIOA2 TIOB TIOB2 TCLK2 XC2 TIOB2 TIOA0 TC2XC2S SYNC INT2 TIOA1 Timer Counter Interrupt Controller Table 33-2. Channel Signal Description Signal Name Description XC0, XC1, XC2 External Clock Inputs Capture Mode: Timer Counter Input TIOA Waveform Mode: Timer Counter Output Capture Mode: Timer Counter Input TIOB Waveform Mode: Timer Counter Input/Output INT Interrupt Signal Output SYNC Synchronization Input Signal 660 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.4 Pin Name List Table 33-3. TC Pin List Pin Name Description Type TCLK0–TCLK2 External Clock Input Input TIOA0–TIOA2 I/O Line A I/O TIOB0–TIOB2 I/O Line B I/O 33.5 Product Dependencies 33.5.1 I/O Lines The pins used for interfacing the compliant external devices may be multiplexed with PIO lines. The programmer must first program the PIO controllers to assign the TC pins to their peripheral functions. Table 33-4. I/O Lines Instance Signal I/O Line Peripheral TC0 TCLK0 PD23 A TC0 TCLK1 PD29 A TC0 TCLK2 PC10 B TC0 TIOA0 PD20 A TC0 TIOA1 PD21 A TC0 TIOA2 PD22 A TC0 TIOB0 PD30 A TC0 TIOB1 PD31 A TC0 TIOB2 PA26 B TC1 TCLK3 PA0 B TC1 TCLK4 PA3 B TC1 TCLK5 PD9 B TC1 TIOA3 PA1 B TC1 TIOA4 PA4 B TC1 TIOA5 PD7 B TC1 TIOB3 PA2 B TC1 TIOB4 PA5 B TC1 TIOB5 PD8 B 33.5.2 Power Management The TC is clocked through the Power Management Controller (PMC), thus the programmer must first configure the PMC to enable the Timer Counter clock. 33.5.3 Interrupt The TC has an interrupt line connected to the Interrupt Controller (IC). Handling the TC interrupt requires programming the IC before configuring the TC. SAM9M11 [DATASHEET] 661 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.6 Functional Description 33.6.1 TC Description The three channels of the Timer Counter are independent and identical in operation. The registers for channel programming are listed in Table 33-5 on page 674. 33.6.2 16-bit Counter Each channel is organized around a 16-bit counter. The value of the counter is incremented at each positive edge of the selected clock. When the counter has reached the value 0xFFFF and passes to 0x0000, an overflow occurs and the COVFS bit in TC_SR (Status Register) is set. The current value of the counter is accessible in real time by reading the Counter Value Register, TC_CV. The counter can be reset by a trigger. In this case, the counter value passes to 0x0000 on the next valid edge of the selected clock. 33.6.3 Clock Selection At block level, input clock signals of each channel can either be connected to the external inputs TCLK0, TCLK1 or TCLK2, or be connected to the internal I/O signals TIOA0, TIOA1 or TIOA2 for chaining by programming the TC_BMR (Block Mode). See Figure 33-2 ”Clock Chaining Selection”. Each channel can independently select an internal or external clock source for its counter:  Internal clock signals: TIMER_CLOCK1, TIMER_CLOCK2, TIMER_CLOCK3, TIMER_CLOCK4, TIMER_CLOCK5  External clock signals: XC0, XC1 or XC2 This selection is made by the TCCLKS bits in the TC Channel Mode Register. The selected clock can be inverted with the CLKI bit in TC_CMR. This allows counting on the opposite edges of the clock. The burst function allows the clock to be validated when an external signal is high. The BURST parameter in the Mode Register defines this signal (none, XC0, XC1, XC2). See Figure 33-3 ”Clock Selection” Note: In all cases, if an external clock is used, the duration of each of its levels must be longer than the master clock period. The external clock frequency must be at least 2.5 times lower than the master clock 662 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 33-2. Clock Chaining Selection TC0XC0S Timer/Counter TCLK0 Channel 0 TIOA1 XC0 TIOA0 TIOA2 XC1 = TCLK1 XC2 = TCLK2 TIOB0 SYNC TC1XC1S Timer/Counter Channel 1 TCLK1 XC0 = TCLK2 TIOA1 TIOA0 XC1 TIOA2 XC2 = TCLK2 TIOB1 SYNC Timer/Counter TC2XC2S Channel 2 XC0 = TCLK0 TIOA2 TCLK2 XC1 = TCLK1 TIOA0 XC2 TIOB2 TIOA1 SYNC Figure 33-3. Clock Selection TCCLKS TIMER_CLOCK1 TIMER_CLOCK2 CLKI TIMER_CLOCK3 TIMER_CLOCK4 TIMER_CLOCK5 Selected XC0 Clock XC1 XC2 BURST 1 SAM9M11 [DATASHEET] 663 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.6.4 Clock Control The clock of each counter can be controlled in two different ways: it can be enabled/disabled and started/stopped. See Figure 33-4.  The clock can be enabled or disabled by the user with the CLKEN and the CLKDIS commands in the Control Register. In Capture Mode it can be disabled by an RB load event if LDBDIS is set to 1 in TC_CMR. In Waveform Mode, it can be disabled by an RC Compare event if CPCDIS is set to 1 in TC_CMR. When disabled, the start or the stop actions have no effect: only a CLKEN command in the Control Register can re- enable the clock. When the clock is enabled, the CLKSTA bit is set in the Status Register.  The clock can also be started or stopped: a trigger (software, synchro, external or compare) always starts the clock. The clock can be stopped by an RB load event in Capture Mode (LDBSTOP = 1 in TC_CMR) or a RC compare event in Waveform Mode (CPCSTOP = 1 in TC_CMR). The start and the stop commands have effect only if the clock is enabled. Figure 33-4. Clock Control Selected Clock Trigger CLKSTA CLKEN CLKDIS Q S R Q S R Stop Disable Event Event Counter Clock 33.6.5 TC Operating Modes Each channel can independently operate in two different modes:  Capture Mode provides measurement on signals.  Waveform Mode provides wave generation. The TC Operating Mode is programmed with the WAVE bit in the TC Channel Mode Register. In Capture Mode, TIOA and TIOB are configured as inputs. In Waveform Mode, TIOA is always configured to be an output and TIOB is an output if it is not selected to be the external trigger. 33.6.6 Trigger A trigger resets the counter and starts the counter clock. Three types of triggers are common to both modes, and a fourth external trigger is available to each mode. Regardless of the trigger used, it will be taken into account at the following active edge of the selected clock. This means that the counter value can be read differently from zero just after a trigger, especially when a low frequency signal is selected as the clock. 664 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The following triggers are common to both modes:  Software Trigger: Each channel has a software trigger, available by setting SWTRG in TC_CCR.  SYNC: Each channel has a synchronization signal SYNC. When asserted, this signal has the same effect as a software trigger. The SYNC signals of all channels are asserted simultaneously by writing TC_BCR (Block Control) with SYNC set.  Compare RC Trigger: RC is implemented in each channel and can provide a trigger when the counter value matches the RC value if CPCTRG is set in TC_CMR. The channel can also be configured to have an external trigger. In Capture Mode, the external trigger signal can be selected between TIOA and TIOB. In Waveform Mode, an external event can be programmed on one of the following signals: TIOB, XC0, XC1 or XC2. This external event can then be programmed to perform a trigger by setting ENETRG in TC_CMR. If an external trigger is used, the duration of the pulses must be longer than the master clock period in order to be detected. 33.6.7 Capture Operating Mode This mode is entered by clearing the WAVE parameter in TC_CMR (Channel Mode Register). Capture Mode allows the TC channel to perform measurements such as pulse timing, frequency, period, duty cycle and phase on TIOA and TIOB signals which are considered as inputs. Figure 33-5 shows the configuration of the TC channel when programmed in Capture Mode. 33.6.8 Capture Registers A and B Registers A and B (RA and RB) are used as capture registers. This means that they can be loaded with the counter value when a programmable event occurs on the signal TIOA. The LDRA parameter in TC_CMR defines the TIOA edge for the loading of register A, and the LDRB parameter defines the TIOA edge for the loading of Register B. RA is loaded only if it has not been loaded since the last trigger or if RB has been loaded since the last loading of RA. RB is loaded only if RA has been loaded since the last trigger or the last loading of RB. Loading RA or RB before the read of the last value loaded sets the Overrun Error Flag (LOVRS) in TC_SR (Status Register). In this case, the old value is overwritten. 33.6.9 Trigger Conditions In addition to the SYNC signal, the software trigger and the RC compare trigger, an external trigger can be defined. The ABETRG bit in TC_CMR selects TIOA or TIOB input signal as an external trigger. The ETRGEDG parameter defines the edge (rising, falling or both) detected to generate an external trigger. If ETRGEDG = 0 (none), the external trigger is disabled. SAM9M11 [DATASHEET] 665 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 33-5. Capture Mode = Register C mpare RC LCOPVCRSS Co COVFS NT LDRBS I S DI LDRAS B DIS LD Capture Register B TECT1R_GSSR TC1_IMR K L C N P E O TACLK SQ R LDBST Capture Register A LDRB Edge Detector S K L C d e d VF Loa O s A i R er RG If nt T u C S R o P C C 6-bit SET Q 1 E R g CLK Tri LDRA Edge Detector KI L G C R T d SW G ETRGEDG EdgeDetector If RA is not loadeor RB is Loaded unter Channel R o T C KS RST ABE mer/ CCL BU Ti T 1 1 2 3 4 5 K K K K K B A C C C C C O O CLO CLO CLO CLO CLO MTI MTI _ _ _ _ _ R R R R R E E E E E M M M M M C0 C1 C2 TI TI TI TI TI X X X C B A N O O SY TI TI 666 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.6.10Waveform Operating Mode Waveform operating mode is entered by setting the WAVE parameter in TC_CMR (Channel Mode Register). In Waveform Operating Mode the TC channel generates 1 or 2 PWM signals with the same frequency and independently programmable duty cycles, or generates different types of one-shot or repetitive pulses. In this mode, TIOA is configured as an output and TIOB is defined as an output if it is not used as an external event (EEVT parameter in TC_CMR). Figure 33-6 shows the configuration of the TC channel when programmed in Waveform Operating Mode. 33.6.11 Waveform Selection Depending on the WAVSEL parameter in TC_CMR (Channel Mode Register), the behavior of TC_CV varies. With any selection, RA, RB and RC can all be used as compare registers. RA Compare is used to control the TIOA output, RB Compare is used to control the TIOB output (if correctly configured) and RC Compare is used to control TIOA and/or TIOB outputs. SAM9M11 [DATASHEET] 667 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 33-6. Waveform Mode OA TIOA OB TIOB TI TI M M rellortnoC tuptuO rellortnoC tuptuO G G ACPC ACPA AEEVT SWTR BCPC BCPB BEEVT SWTR A B CPCDIS CPCSTOP Register C mpare RC = o S C DI K L C = CLKEN S R Register B mpare RB CCPPCBSS o C CPAS NT STA Q COVFS I K CL A A = ETRGS Register mpare R TC1_SR TC1_IMR o C OVF L S R VSEL Counter RESET WAVSE Q WA 6-bit 1 CLK Trig G R T E N E CLKI nnel a h C SWTRG EEVTEDG Edge Detector mer/Counter Ti CCLKS BURST EEVT T 1 12 3 4 5 KK K K K CC C C C OO O O O LL L L L CC C C C __ _ _ _ RR R R R TIMETIME TIME TIME TIME XC0 XC1 XC2 C N B Y O S TI 668 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.6.11.1 WAVSEL = 00 When WAVSEL = 00, the value of TC_CV is incremented from 0 to 0xFFFF. Once 0xFFFF has been reached, the value of TC_CV is reset. Incrementation of TC_CV starts again and the cycle continues. See Figure 33-7. An external event trigger or a software trigger can reset the value of TC_CV. It is important to note that the trigger may occur at any time. See Figure 33-8. RC Compare cannot be programmed to generate a trigger in this configuration. At the same time, RC Compare can stop the counter clock (CPCSTOP = 1 in TC_CMR) and/or disable the counter clock (CPCDIS = 1 in TC_CMR). Figure 33-7. WAVSEL = 00 without trigger Counter Value Counter cleared by compare match with 0xFFFF 0xFFFF R C R B R A Time Waveform Examples TIOB TIOA Figure 33-8. WAVSEL = 00 with trigger Counter Value Counter cleared by compare match with 0xFFFF 0xFFFF Counter cleared by trigger R C R B R A Time Waveform Examples TIOB TIOA SAM9M11 [DATASHEET] 669 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.6.11.2 WAVSEL = 10 When WAVSEL = 10, the value of TC_CV is incremented from 0 to the value of RC, then automatically reset on a RC Compare. Once the value of TC_CV has been reset, it is then incremented and so on. See Figure 33-9. It is important to note that TC_CV can be reset at any time by an external event or a software trigger if both are programmed correctly. See Figure 33-10. In addition, RC Compare can stop the counter clock (CPCSTOP = 1 in TC_CMR) and/or disable the counter clock (CPCDIS = 1 in TC_CMR). Figure 33-9. WAVSEL = 10 Without Trigger Counter Value 0xFFFF Counter cleared by compare match with RC R C R B R A Time Waveform Examples TIOB TIOA Figure 33-10. WAVSEL = 10 With Trigger Counter Value 0xFFFF Counter cleared by compare match with RC Counter cleared by trigger R C R B R A Time Waveform Examples TIOB TIOA 670 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.6.11.3 WAVSEL = 01 When WAVSEL = 01, the value of TC_CV is incremented from 0 to 0xFFFF. Once 0xFFFF is reached, the value of TC_CV is decremented to 0, then re-incremented to 0xFFFF and so on. See Figure 33-11. A trigger such as an external event or a software trigger can modify TC_CV at any time. If a trigger occurs while TC_CV is incrementing, TC_CV then decrements. If a trigger is received while TC_CV is decrementing, TC_CV then increments. See Figure 33-12. RC Compare cannot be programmed to generate a trigger in this configuration. At the same time, RC Compare can stop the counter clock (CPCSTOP = 1) and/or disable the counter clock (CPCDIS = 1). Figure 33-11. WAVSEL = 01 Without Trigger Counter Value Counter decremented by compare match with 0xFFFF 0xFFFF R C R B R A Time Waveform Examples TIOB TIOA Figure 33-12. WAVSEL = 01 With Trigger Counter Value Counter decremented by compare match with 0xFFFF 0xFFFF Counter decremented by trigger R C R B Counter incremented by trigger R A Time Waveform Examples TIOB TIOA SAM9M11 [DATASHEET] 671 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.6.11.4 WAVSEL = 11 When WAVSEL = 11, the value of TC_CV is incremented from 0 to RC. Once RC is reached, the value of TC_CV is decremented to 0, then re-incremented to RC and so on. See Figure 33-13. A trigger such as an external event or a software trigger can modify TC_CV at any time. If a trigger occurs while TC_CV is incrementing, TC_CV then decrements. If a trigger is received while TC_CV is decrementing, TC_CV then increments. See Figure 33-14. RC Compare can stop the counter clock (CPCSTOP = 1) and/or disable the counter clock (CPCDIS = 1). Figure 33-13. WAVSEL = 11 Without Trigger Counter Value 0xFFFF Counter decremented by compare match with RC R C R B R A Time Waveform Examples TIOB TIOA Figure 33-14. WAVSEL = 11 With Trigger Counter Value 0xFFFF Counter decremented by compare match with RC R C Counter decremented by trigger R B Counter incremented by trigger R A Time Waveform Examples TIOB TIOA 672 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.6.12External Event/Trigger Conditions An external event can be programmed to be detected on one of the clock sources (XC0, XC1, XC2) or TIOB. The external event selected can then be used as a trigger. The EEVT parameter in TC_CMR selects the external trigger. The EEVTEDG parameter defines the trigger edge for each of the possible external triggers (rising, falling or both). If EEVTEDG is cleared (none), no external event is defined. If TIOB is defined as an external event signal (EEVT = 0), TIOB is no longer used as an output and the compare register B is not used to generate waveforms and subsequently no IRQs. In this case the TC channel can only generate a waveform on TIOA. When an external event is defined, it can be used as a trigger by setting bit ENETRG in TC_CMR. As in Capture Mode, the SYNC signal and the software trigger are also available as triggers. RC Compare can also be used as a trigger depending on the parameter WAVSEL. 33.6.13Output Controller The output controller defines the output level changes on TIOA and TIOB following an event. TIOB control is used only if TIOB is defined as output (not as an external event). The following events control TIOA and TIOB: software trigger, external event and RC compare. RA compare controls TIOA and RB compare controls TIOB. Each of these events can be programmed to set, clear or toggle the output as defined in the corresponding parameter in TC_CMR. SAM9M11 [DATASHEET] 673 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.7 Timer Counter (TC) User Interface Table 33-5. Register Mapping Offset(1) Register Name Access Reset 0x00 + channel * 0x40 + 0x00 Channel Control Register TC_CCR Write-only – 0x00 + channel * 0x40 + 0x04 Channel Mode Register TC_CMR Read/Write 0 0x00 + channel * 0x40 + 0x08 Reserved – – – 0x00 + channel * 0x40 + 0x0C Reserved – – – 0x00 + channel * 0x40 + 0x10 Counter Value TC_CV Read-only 0 0x00 + channel * 0x40 + 0x14 Register A TC_RA Read/Write(2) 0 0x00 + channel * 0x40 + 0x18 Register B TC_RB Read/Write(2) 0 0x00 + channel * 0x40 + 0x1C Register C TC_RC Read/Write 0 0x00 + channel * 0x40 + 0x20 Status Register TC_SR Read-only 0 0x00 + channel * 0x40 + 0x24 Interrupt Enable Register TC_IER Write-only – 0x00 + channel * 0x40 + 0x28 Interrupt Disable Register TC_IDR Write-only – 0x00 + channel * 0x40 + 0x2C Interrupt Mask Register TC_IMR Read-only 0 0xC0 Block Control Register TC_BCR Write-only – 0xC4 Block Mode Register TC_BMR Read/Write 0 0xD8 Reserved – – – 0xE4 Reserved – – – 0xFC Reserved – – – Notes: 1. Channel index ranges from 0 to 2. 2. Read-only if WAVE = 0 674 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.7.1 TC Block Control Register Name: TC_BCR Address: 0xFFF7C0C0 (0), 0xFFFD40C0 (1) Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – SYNC • SYNC: Synchro Command 0: No effect. 1: Asserts the SYNC signal which generates a software trigger simultaneously for each of the channels. SAM9M11 [DATASHEET] 675 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.7.2 TC Block Mode Register Name: TC_BMR Address: 0xFFF7C0C4 (0), 0xFFFD40C4 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – TC2XC2S TC1XC1S TC0XC0S • TC0XC0S: External Clock Signal 0 Selection TC0XC0S Signal Connected to XC0 0 0 TCLK0 0 1 none 1 0 TIOA1 1 1 TIOA2 • TC1XC1S: External Clock Signal 1 Selection TC1XC1S Signal Connected to XC1 0 0 TCLK1 0 1 none 1 0 TIOA0 1 1 TIOA2 • TC2XC2S: External Clock Signal 2 Selection TC2XC2S Signal Connected to XC2 0 0 TCLK2 0 1 none 1 0 TIOA0 1 1 TIOA1 676 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.7.3 TC Channel Control Register Name: TC_CCRx [x=0..2] Address: 0xFFF7C000 (0)[0], 0xFFF7C040 (0)[1], 0xFFF7C080 (0)[2], 0xFFFD4000 (1)[0], 0xFFFD4040 (1)[1], 0xFFFD4080 (1)[2] Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – SWTRG CLKDIS CLKEN • CLKEN: Counter Clock Enable Command 0: No effect. 1: Enables the clock if CLKDIS is not 1. • CLKDIS: Counter Clock Disable Command 0: No effect. 1: Disables the clock. • SWTRG: Software Trigger Command 0: No effect. 1: A software trigger is performed: the counter is reset and the clock is started. SAM9M11 [DATASHEET] 677 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.7.4 TC Channel Mode Register: Capture Mode Name: TC_CMRx [x=0..2] (WAVE = 0) Address: 0xFFF7C004 (0)[0], 0xFFF7C044 (0)[1], 0xFFF7C084 (0)[2], 0xFFFD4004 (1)[0], 0xFFFD4044 (1)[1], 0xFFFD4084 (1)[2] Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – LDRB LDRA 15 14 13 12 11 10 9 8 WAVE CPCTRG – – – ABETRG ETRGEDG 7 6 5 4 3 2 1 0 LDBDIS LDBSTOP BURST CLKI TCCLKS • TCCLKS: Clock Selection TCCLKS Clock Selected 0 0 0 TIMER_CLOCK1 0 0 1 TIMER_CLOCK2 0 1 0 TIMER_CLOCK3 0 1 1 TIMER_CLOCK4 1 0 0 TIMER_CLOCK5 1 0 1 XC0 1 1 0 XC1 1 1 1 XC2 • CLKI: Clock Invert 0: counter is incremented on rising edge of the clock. 1: counter is incremented on falling edge of the clock. • BURST: Burst Signal Selection BURST Description 0 0 The clock is not gated by an external signal. 0 1 XC0 is ANDed with the selected clock. 1 0 XC1 is ANDed with the selected clock. 1 1 XC2 is ANDed with the selected clock. • LDBSTOP: Counter Clock Stopped with RB Loading 0: counter clock is not stopped when RB loading occurs. 1: counter clock is stopped when RB loading occurs. 678 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• LDBDIS: Counter Clock Disable with RB Loading 0: counter clock is not disabled when RB loading occurs. 1: counter clock is disabled when RB loading occurs. • ETRGEDG: External Trigger Edge Selection ETRGEDG Edge 0 0 none 0 1 rising edge 1 0 falling edge 1 1 each edge • ABETRG: TIOA or TIOB External Trigger Selection 0: TIOB is used as an external trigger. 1: TIOA is used as an external trigger. • CPCTRG: RC Compare Trigger Enable 0: RC Compare has no effect on the counter and its clock. 1: RC Compare resets the counter and starts the counter clock. • WAVE 0: Capture Mode is enabled. 1: Capture Mode is disabled (Waveform Mode is enabled). • LDRA: RA Loading Selection LDRA Edge 0 0 none 0 1 rising edge of TIOA 1 0 falling edge of TIOA 1 1 each edge of TIOA • LDRB: RB Loading Selection LDRB Edge 0 0 none 0 1 rising edge of TIOA 1 0 falling edge of TIOA 1 1 each edge of TIOA SAM9M11 [DATASHEET] 679 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.7.5 TC Channel Mode Register: Waveform Mode Name: TC_CMRx [x=0..2] (WAVE = 1) Address: 0xFFF7C004 (0)[0], 0xFFF7C044 (0)[1], 0xFFF7C084 (0)[2], 0xFFFD4004 (1)[0], 0xFFFD4044 (1)[1], 0xFFFD4084 (1)[2] Access: Read/Write 31 30 29 28 27 26 25 24 BSWTRG BEEVT BCPC BCPB 23 22 21 20 19 18 17 16 ASWTRG AEEVT ACPC ACPA 15 14 13 12 11 10 9 8 WAVE WAVSEL ENETRG EEVT EEVTEDG 7 6 5 4 3 2 1 0 CPCDIS CPCSTOP BURST CLKI TCCLKS • TCCLKS: Clock Selection TCCLKS Clock Selected 0 0 0 TIMER_CLOCK1 0 0 1 TIMER_CLOCK2 0 1 0 TIMER_CLOCK3 0 1 1 TIMER_CLOCK4 1 0 0 TIMER_CLOCK5 1 0 1 XC0 1 1 0 XC1 1 1 1 XC2 • CLKI: Clock Invert 0: counter is incremented on rising edge of the clock. 1: counter is incremented on falling edge of the clock. • BURST: Burst Signal Selection BURST Description 0 0 The clock is not gated by an external signal. 0 1 XC0 is ANDed with the selected clock. 1 0 XC1 is ANDed with the selected clock. 1 1 XC2 is ANDed with the selected clock. • CPCSTOP: Counter Clock Stopped with RC Compare 0: counter clock is not stopped when counter reaches RC. 1: counter clock is stopped when counter reaches RC. • CPCDIS: Counter Clock Disable with RC Compare 0: counter clock is not disabled when counter reaches RC. 1: counter clock is disabled when counter reaches RC. 680 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• EEVTEDG: External Event Edge Selection EEVTEDG Edge 0 0 none 0 1 rising edge 1 0 falling edge 1 1 each edge • EEVT: External Event Selection EEVT Signal selected as external event TIOB Direction 0 0 TIOB input (1) 0 1 XC0 output 1 0 XC1 output 1 1 XC2 output Note: 1. If TIOB is chosen as the external event signal, it is configured as an input and no longer generates waveforms and subsequently no IRQs. • ENETRG: External Event Trigger Enable 0: the external event has no effect on the counter and its clock. In this case, the selected external event only controls the TIOA output. 1: the external event resets the counter and starts the counter clock. • WAVSEL: Waveform Selection WAVSEL Effect 0 0 UP mode without automatic trigger on RC Compare 1 0 UP mode with automatic trigger on RC Compare 0 1 UPDOWN mode without automatic trigger on RC Compare 1 1 UPDOWN mode with automatic trigger on RC Compare • WAVE 0: Waveform Mode is disabled (Capture Mode is enabled). 1: Waveform Mode is enabled. • ACPA: RA Compare Effect on TIOA ACPA Effect 0 0 none 0 1 set 1 0 clear 1 1 toggle SAM9M11 [DATASHEET] 681 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• ACPC: RC Compare Effect on TIOA ACPC Effect 0 0 none 0 1 set 1 0 clear 1 1 toggle • AEEVT: External Event Effect on TIOA AEEVT Effect 0 0 none 0 1 set 1 0 clear 1 1 toggle • ASWTRG: Software Trigger Effect on TIOA ASWTRG Effect 0 0 none 0 1 set 1 0 clear 1 1 toggle • BCPB: RB Compare Effect on TIOB BCPB Effect 0 0 none 0 1 set 1 0 clear 1 1 toggle • BCPC: RC Compare Effect on TIOB BCPC Effect 0 0 none 0 1 set 1 0 clear 1 1 toggle • BEEVT: External Event Effect on TIOB BEEVT Effect 0 0 none 0 1 set 1 0 clear 1 1 toggle 682 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• BSWTRG: Software Trigger Effect on TIOB BSWTRG Effect 0 0 none 0 1 set 1 0 clear 1 1 toggle SAM9M11 [DATASHEET] 683 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.7.6 TC Counter Value Register Name: TC_CVx [x=0..2] Address: 0xFFF7C010 (0)[0], 0xFFF7C050 (0)[1], 0xFFF7C090 (0)[2], 0xFFFD4010 (1)[0], 0xFFFD4050 (1)[1], 0xFFFD4090 (1)[2] Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 CV 7 6 5 4 3 2 1 0 CV • CV: Counter Value CV contains the counter value in real time. 684 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.7.7 TC Register A Name: TC_RAx [x=0..2] Address: 0xFFF7C014 (0)[0], 0xFFF7C054 (0)[1], 0xFFF7C094 (0)[2], 0xFFFD4014 (1)[0], 0xFFFD4054 (1)[1], 0xFFFD4094 (1)[2] Access: Read-only if WAVE = 0, Read/Write if WAVE = 1 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 RA 7 6 5 4 3 2 1 0 RA • RA: Register A RA contains the Register A value in real time. SAM9M11 [DATASHEET] 685 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.7.8 TC Register B Name: TC_RBx [x=0..2] Address: 0xFFF7C018 (0)[0], 0xFFF7C058 (0)[1], 0xFFF7C098 (0)[2], 0xFFFD4018 (1)[0], 0xFFFD4058 (1)[1], 0xFFFD4098 (1)[2] Access: Read-only if WAVE = 0, Read/Write if WAVE = 1 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 RB 7 6 5 4 3 2 1 0 RB • RB: Register B RB contains the Register B value in real time. 686 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.7.9 TC Register C Name: TC_RCx [x=0..2] Address: 0xFFF7C01C (0)[0], 0xFFF7C05C (0)[1], 0xFFF7C09C (0)[2], 0xFFFD401C (1)[0], 0xFFFD405C (1)[1], 0xFFFD409C (1)[2] Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 RC 7 6 5 4 3 2 1 0 RC • RC: Register C RC contains the Register C value in real time. SAM9M11 [DATASHEET] 687 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.7.10TC Status Register Name: TC_SRx [x=0..2] Address: 0xFFF7C020 (0)[0], 0xFFF7C060 (0)[1], 0xFFF7C0A0 (0)[2], 0xFFFD4020 (1)[0], 0xFFFD4060 (1)[1], 0xFFFD40A0 (1)[2] Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – MTIOB MTIOA CLKSTA 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 ETRGS LDRBS LDRAS CPCS CPBS CPAS LOVRS COVFS • COVFS: Counter Overflow Status 0: No counter overflow has occurred since the last read of the Status Register. 1: A counter overflow has occurred since the last read of the Status Register. • LOVRS: Load Overrun Status 0: Load overrun has not occurred since the last read of the Status Register or WAVE = 1. 1: RA or RB have been loaded at least twice without any read of the corresponding register since the last read of the Sta- tus Register, if WAVE = 0. • CPAS: RA Compare Status 0: RA Compare has not occurred since the last read of the Status Register or WAVE = 0. 1: RA Compare has occurred since the last read of the Status Register, if WAVE = 1. • CPBS: RB Compare Status 0: RB Compare has not occurred since the last read of the Status Register or WAVE = 0. 1: RB Compare has occurred since the last read of the Status Register, if WAVE = 1. • CPCS: RC Compare Status 0: RC Compare has not occurred since the last read of the Status Register. 1: RC Compare has occurred since the last read of the Status Register. • LDRAS: RA Loading Status 0: RA Load has not occurred since the last read of the Status Register or WAVE = 1. 1: RA Load has occurred since the last read of the Status Register, if WAVE = 0. • LDRBS: RB Loading Status 0: RB Load has not occurred since the last read of the Status Register or WAVE = 1. 1: RB Load has occurred since the last read of the Status Register, if WAVE = 0. 688 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• ETRGS: External Trigger Status 0: external trigger has not occurred since the last read of the Status Register. 1: external trigger has occurred since the last read of the Status Register. • CLKSTA: Clock Enabling Status 0: clock is disabled. 1: clock is enabled. • MTIOA: TIOA Mirror 0: TIOA is low. If WAVE = 0, this means that TIOA pin is low. If WAVE = 1, this means that TIOA is driven low. 1: TIOA is high. If WAVE = 0, this means that TIOA pin is high. If WAVE = 1, this means that TIOA is driven high. • MTIOB: TIOB Mirror 0: TIOB is low. If WAVE = 0, this means that TIOB pin is low. If WAVE = 1, this means that TIOB is driven low. 1: TIOB is high. If WAVE = 0, this means that TIOB pin is high. If WAVE = 1, this means that TIOB is driven high. SAM9M11 [DATASHEET] 689 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.7.11 TC Interrupt Enable Register Name: TC_IERx [x=0..2] Address: 0xFFF7C024 (0)[0], 0xFFF7C064 (0)[1], 0xFFF7C0A4 (0)[2], 0xFFFD4024 (1)[0], 0xFFFD4064 (1)[1], 0xFFFD40A4 (1)[2] Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 ETRGS LDRBS LDRAS CPCS CPBS CPAS LOVRS COVFS • COVFS: Counter Overflow 0: No effect. 1: Enables the Counter Overflow Interrupt. • LOVRS: Load Overrun 0: No effect. 1: Enables the Load Overrun Interrupt. • CPAS: RA Compare 0: No effect. 1: Enables the RA Compare Interrupt. • CPBS: RB Compare 0: No effect. 1: Enables the RB Compare Interrupt. • CPCS: RC Compare 0: No effect. 1: Enables the RC Compare Interrupt. • LDRAS: RA Loading 0: No effect. 1: Enables the RA Load Interrupt. • LDRBS: RB Loading 0: No effect. 1: Enables the RB Load Interrupt. • ETRGS: External Trigger 0: No effect. 1: Enables the External Trigger Interrupt. 690 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.7.12TC Interrupt Disable Register Name: TC_IDRx [x=0..2] Addresses 0xFFF7C028 (0)[0], 0xFFF7C068 (0)[1], 0xFFF7C0A8 (0)[2], 0xFFFD4028 (1)[0], 0xFFFD4068 (1)[1], 0xFFFD40A8 (1)[2] Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 ETRGS LDRBS LDRAS CPCS CPBS CPAS LOVRS COVFS • COVFS: Counter Overflow 0: No effect. 1: Disables the Counter Overflow Interrupt. • LOVRS: Load Overrun 0: No effect. 1: Disables the Load Overrun Interrupt (if WAVE = 0). • CPAS: RA Compare 0: No effect. 1: Disables the RA Compare Interrupt (if WAVE = 1). • CPBS: RB Compare 0: No effect. 1: Disables the RB Compare Interrupt (if WAVE = 1). • CPCS: RC Compare 0: No effect. 1: Disables the RC Compare Interrupt. • LDRAS: RA Loading 0: No effect. 1: Disables the RA Load Interrupt (if WAVE = 0). • LDRBS: RB Loading 0: No effect. 1: Disables the RB Load Interrupt (if WAVE = 0). • ETRGS: External Trigger 0: No effect. 1: Disables the External Trigger Interrupt. SAM9M11 [DATASHEET] 691 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.7.13TC Interrupt Mask Register Name: TC_IMRx [x=0..2] Address: 0xFFF7C02C (0)[0], 0xFFF7C06C (0)[1], 0xFFF7C0AC (0)[2], 0xFFFD402C (1)[0], 0xFFFD406C (1)[1], 0xFFFD40AC (1)[2] Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 ETRGS LDRBS LDRAS CPCS CPBS CPAS LOVRS COVFS • COVFS: Counter Overflow 0: The Counter Overflow Interrupt is disabled. 1: The Counter Overflow Interrupt is enabled. • LOVRS: Load Overrun 0: The Load Overrun Interrupt is disabled. 1: The Load Overrun Interrupt is enabled. • CPAS: RA Compare 0: The RA Compare Interrupt is disabled. 1: The RA Compare Interrupt is enabled. • CPBS: RB Compare 0: The RB Compare Interrupt is disabled. 1: The RB Compare Interrupt is enabled. • CPCS: RC Compare 0: The RC Compare Interrupt is disabled. 1: The RC Compare Interrupt is enabled. • LDRAS: RA Loading 0: The Load RA Interrupt is disabled. 1: The Load RA Interrupt is enabled. • LDRBS: RB Loading 0: The Load RB Interrupt is disabled. 1: The Load RB Interrupt is enabled. • ETRGS: External Trigger 0: The External Trigger Interrupt is disabled. 1: The External Trigger Interrupt is enabled. 692 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34. DMA Controller (DMAC) 34.1 Description The DMA Controller (DMAC) is an AHB-central DMA controller core that transfers data from a source peripheral to a destination peripheral over one or more AMBA buses. One channel is required for each source/destination pair. In the most basic configuration, the DMAC has one master interface and one channel. The master interface reads the data from a source and writes it to a destination. Two AMBA transfers are required for each DMAC data transfer. This is also known as a dual-access transfer. The DMAC is programmed via the APB interface. SAM9M11 [DATASHEET] 693 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.2 Embedded Characteristics  Two Masters  Embeds 8 channels  64 bytes/FIFO for Channel Buffering  Linked List support with Status Write Back operation at End of Transfer  Word, HalfWord, Byte transfer support  Memory to memory transfer  Peripheral to memory  Memory to peripheral  Acting as two Matrix Masters  Embeds 8 unidirectional channels with programmable priority  Address Generation ̶ Source/Destination address programming ̶ Address increment, decrement or no change ̶ DMA chaining support for multiple non-contiguous data blocks through use of linked lists ̶ Scatter support for placing fields into a system memory area from a contiguous transfer. Writing a stream of data into non-contiguous fields in system memory ̶ Gather support for extracting fields from a system memory area into a contiguous transfer ̶ User enabled auto-reloading of source, destination and control registers from initially programmed values at the end of a block transfer ̶ Auto-loading of source, destination and control registers from system memory at end of block transfer in block chaining mode ̶ Unaligned system address to data transfer width supported in hardware  Channel Buffering ̶ 16-word FIFO ̶ Automatic packing/unpacking of data to fit FIFO width  Channel Control ̶ Programmable multiple transaction size for each channel ̶ Support for cleanly disabling a channel without data loss ̶ Suspend DMA operation ̶ Programmable DMA lock transfer support  Transfer Initiation ̶ Support for Software handshaking interface. Memory mapped registers can be used to control the flow of a DMA transfer in place of a hardware handshaking interface  Interrupt ̶ Programmable Interrupt generation on DMA Transfer completion Block Transfer completion, Single/Multiple transaction completion or Error condition 694 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.3 DMA Controller Peripheral Connections The DMA Controller handles the transfer between peripherals and memory and receives triggers from the peripherals connected on APB0 (see Table 34-1). Table 34-1. DMA Channel Definition Instance Name T/R DMA Channel HW Interface Number MCI0 TX/RX 0 SPI0 TX 1 SPI0 RX 2 SPI1 TX 3 SPI1 RX 4 SSC0 TX 5 SSC0 RX 6 SSC1 TX 7 SSC1 RX 8 AC97C TX 9 AC97C RX 10 AES TX 11 AES RS 12 MCI1 TX/RX 13 SAM9M11 [DATASHEET] 695 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.4 Block Diagram Figure 34-1. DMA Controller (DMAC) Block Diagram AMBA AHB Layer 1 DMA AHB Lite Master Interface 1 DMA Global Control DMA Global and Data Mux Request Arbiter DMA Write DMA Destination Datapath Bundles Requests Pool DMA Channel n DMA Destination Atmel APB rev2 Interface DMA Atmel DMA Channel 2 APB Status Interface DMA Channel 1 Registers DMA Channel 0 Configuration DMA Destination Registers DMA Channel 0 Control State Machine Write data path to destination Destination Pointer Management DMA Interrupt DMA Interrupt Controller DMA FIFO Controller DMA FIFO Trigger Manager DMA Hardware Up to 64 bytes External Handshaking Triggers DMA Interface REQ/ACK Soft Interface Triggers DMA Source DMA Channel 0 Control State Machine Read data path Source Pointer from source Management DMA Read DMA Source Datapath Bundles Requests Pool DMA Global Control DMA Global and Data Mux Request Arbiter DMA AHB Lite Master Interface 0 AMBA AHB Layer 0 696 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.5 Functional Description 34.5.1 Basic Definitions Source peripheral: Device on an AMBA layer from where the DMAC reads data, which is then stored in the channel FIFO. The source peripheral teams up with a destination peripheral to form a channel. Destination peripheral: Device to which the DMAC writes the stored data from the FIFO (previously read from the source peripheral). Memory: Source or destination that is always “ready” for a DMAC transfer and does not require a handshaking interface to interact with the DMAC. Channel: Read/Write datapath between a source peripheral on one configured AMBA layer and a destination peripheral on the same or different AMBA layer that occurs through the channel FIFO. If the source peripheral is not memory, then a source handshaking interface is assigned to the channel. If the destination peripheral is not memory, then a destination handshaking interface is assigned to the channel. Source and destination handshaking interfaces can be assigned dynamically by programming the channel registers. Master interface: DMAC is a master on the AHB bus reading data from the source and writing it to the destination over the AHB bus. Slave interface: The APB interface over which the DMAC is programmed. The slave interface in practice could be on the same layer as any of the master interfaces or on a separate layer. Handshaking interface: A set of signal registers that conform to a protocol and handshake between the DMAC and source or destination peripheral to control the transfer of a single or chunk transfer between them. This interface is used to request, acknowledge, and control a DMAC transaction. A channel can receive a request through one of two types of handshaking interface: hardware or software. Hardware handshaking interface: Uses hardware signals to control the transfer of a single or chunk transfer between the DMAC and the source or destination peripheral. Software handshaking interface: Uses software registers to contr5ol the transfer of a single or chunk transfer between the DMAC and the source or destination peripheral. No special DMAC handshaking signals are needed on the I/O of the peripheral. This mode is useful for interfacing an existing peripheral to the DMAC without modifying it. Flow controller: The device (either the DMAC or source/destination peripheral) that determines the length of and terminates a DMAC buffer transfer. If the length of a buffer is known before enabling the channel, then the DMAC should be programmed as the flow controller. If the length of a buffer is not known prior to enabling the channel, the source or destination peripheral needs to terminate a buffer transfer. In this mode, the peripheral is the flow controller. Transfer hierarchy: Figure 34-2 on page 698 illustrates the hierarchy between DMAC transfers, buffer transfers, chunk or single, and AMBA transfers (single or burst) for non-memory peripherals. Figure 34-3 on page 698 shows the transfer hierarchy for memory. SAM9M11 [DATASHEET] 697 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 34-2. DMAC Transfer Hierarchy for Non-Memory Peripheral HDMA Transfer DMA Transfer Level Buffer Transfer Buffer Buffer Buffer Level Chunk Chunk Chunk Single DMA Transaction Transfer Transfer Transfer Transfer Level AMBA AMBA AMBA AMBA AMBA Burst Burst Burst Single Single AMBA Transfer Transfer Transfer Transfer Transfer Transfer Level Figure 34-3. DMAC Transfer Hierarchy for Memory HDMA Transfer DMA Transfer Level Buffer Transfer Buffer Buffer Buffer Level AMBA AMBA AMBA AMBA AMBA Transfer Burst Burst Burst Single Transfer Transfer Transfer Transfer Level Buffer: A buffer of DMAC data. The amount of data (length) is determined by the flow controller. For transfers between the DMAC and memory, a buffer is broken directly into a sequence of AMBA bursts and AMBA single transfers. For transfers between the DMAC and a non-memory peripheral, a buffer is broken into a sequence of DMAC transactions (single and chunks). These are in turn broken into a sequence of AMBA transfers. Transaction: A basic unit of a DMAC transfer as determined by either the hardware or software handshaking interface. A transaction is only relevant for transfers between the DMAC and a source or destination peripheral if the source or destination peripheral is a non-memory device. There are two types of transactions: single transfer and chunk transfer. ̶ Single transfer: The length of a single transaction is always 1 and is converted to a single AMBA access. ̶ Chunk transfer: The length of a chunk is programmed into the DMAC. The chunk is then converted into a sequence of AHB access.DMAC executes each AMBA burst transfer by performing incremental bursts that are no longer than 16 beats. DMAC transfer: Software controls the number of buffers in a DMAC transfer. Once the DMAC transfer has completed, then hardware within the DMAC disables the channel and can generate an interrupt to signal the completion of the DMAC transfer. You can then re-program the channel for a new DMAC transfer. Single-buffer DMAC transfer: Consists of a single buffer. 698 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Multi-buffer DMAC transfer: A DMAC transfer may consist of multiple DMAC buffers. Multi-buffer DMAC transfers are supported through buffer chaining (linked list pointers), auto-reloading of channel registers, and contiguous buffers. The source and destination can independently select which method to use. ̶ Linked lists (buffer chaining) – A descriptor pointer (DSCR) points to the location in system memory where the next linked list item (LLI) exists. The LLI is a set of registers that describe the next buffer (buffer descriptor) and a descriptor pointer register. The DMAC fetches the LLI at the beginning of every buffer when buffer chaining is enabled. ̶ Replay – The DMAC automatically reloads the channel registers at the end of each buffers to the value when the channel was first enabled. ̶ Contiguous buffers – Where the address of the next buffer is selected to be a continuation from the end of the previous buffer. Picture-in-Picture Mode: DMAC contains a picture-in-picture mode support. When this mode is enabled, addresses are automatically incremented by a programmable value when the DMAC channel transfer count reaches a user defined boundary. Figure 34-4 illustrates a memory mapped image 4:2:2 encoded located at image_base_address in memory. A user defined start address is defined at Picture_start_address. The incremented value is set to memory_hole_size = image_width - picture_width, and the boundary is set to picture_width. Figure 34-4. Picture-In-Picture Mode Support Channel locking: Software can program a channel to keep the AHB master interface by locking the arbitration for the master bus interface for the duration of a DMAC transfer, buffer, or chunk. Bus locking: Software can program a channel to maintain control of the AMBA bus by asserting hmastlock for the duration of a DMAC transfer, buffer, or transaction (single or chunk). Channel locking is asserted for the duration of bus locking at a minimum. SAM9M11 [DATASHEET] 699 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.5.2 Memory Peripherals Figure 34-3 on page 698 shows the DMAC transfer hierarchy of the DMAC for a memory peripheral. There is no handshaking interface with the DMAC, and therefore the memory peripheral can never be a flow controller. Once the channel is enabled, the transfer proceeds immediately without waiting for a transaction request. The alternative to not having a transaction-level handshaking interface is to allow the DMAC to attempt AMBA transfers to the peripheral once the channel is enabled. If the peripheral slave cannot accept these AMBA transfers, it inserts wait states onto the bus until it is ready; it is not recommended that more than 16 wait states be inserted onto the bus. By using the handshaking interface, the peripheral can signal to the DMAC that it is ready to transmit/receive data, and then the DMAC can access the peripheral without the peripheral inserting wait states onto the bus. 34.5.3 Handshaking Interface Handshaking interfaces are used at the transaction level to control the flow of single or chunk transfers. The operation of the handshaking interface is different and depends on whether the peripheral or the DMAC is the flow controller. The peripheral uses the handshaking interface to indicate to the DMAC that it is ready to transfer/accept data over the AMBA bus. A non-memory peripheral can request a DMAC transfer through the DMAC using one of two handshaking interfaces:  Hardware handshaking  Software handshaking Software selects between the hardware or software handshaking interface on a per-channel basis. Software handshaking is accomplished through memory-mapped registers, while hardware handshaking is accomplished using a dedicated handshaking interface. 34.5.3.1 Software Handshaking When the slave peripheral requires the DMAC to perform a DMAC transaction, it communicates this request by sending an interrupt to the CPU or interrupt controller. The interrupt service routine then uses the software registers to initiate and control a DMAC transaction. These software registers are used to implement the software handshaking interface. The SRC_H2SEL/DST_H2SEL bit in the DMAC_CFGx channel configuration register must be set to zero to enable software handshaking. When the peripheral is not the flow controller, then the last transaction register DMAC_LAST is not used, and the values in these registers are ignored. 34.5.3.2 Chunk Transactions Writing a 1 to the DMAC_CREQ[2x] register starts a source chunk transaction request, where x is the channel number. Writing a 1 to the DMAC_CREQ[2x+1] register starts a destination chunk transfer request, where x is the channel number. Upon completion of the chunk transaction, the hardware clears the DMAC_CREQ[2x] or DMAC_CREQ[2x+1]. 34.5.3.3 Single Transactions Writing a 1 to the DMAC_SREQ[2x] register starts a source single transaction request, where x is the channel number. Writing a 1 to the DMAC_SREQ[2x+1] register starts a destination single transfer request, where x is the channel number. Upon completion of the chunk transaction, the hardware clears the DMAC_SREQ[x] or DMAC_SREQ[2x+1]. Software can poll the relevant channel bit in the DMAC_CREQ[2x]/DMAC_CREQ[2x+1] and DMAC_SREQ[x]/DMAC_SREQ[2x+1] registers. When both are 0, then either the requested chunk or single transaction has completed. 700 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.5.4 DMAC Transfer Types A DMAC transfer may consist of single or multi-buffers transfers. On successive buffers of a multi-buffer transfer, the DMAC_SADDRx/DMAC_DADDRx registers in the DMAC are reprogrammed using either of the following methods:  Buffer chaining using linked lists  Replay mode  Contiguous address between buffers On successive buffers of a multi-buffer transfer, the DMAC_CTRLAx and DMAC_CTRLBx registers in the DMAC are re-programmed using either of the following methods:  Buffer chaining using linked lists  Replay mode When buffer chaining, using linked lists is the multi-buffer method of choice, and on successive buffers, the DMAC_DSCRx register in the DMAC is re-programmed using the following method:  Buffer chaining using linked lists A buffer descriptor (LLI) consists of following registers, DMAC_SADDRx, DMAC_DADDRx, DMAC_DSCRx, DMAC_CTRLAx, DMAC_CTRLBx.These registers, along with the DMAC_CFGx register, are used by the DMAC to set up and describe the buffer transfer. 34.5.4.1 Multi-buffer Transfers 34.5.4.2 Buffer Chaining Using Linked Lists In this case, the DMAC re-programs the channel registers prior to the start of each buffer by fetching the buffer descriptor for that buffer from system memory. This is known as an LLI update. DMAC buffer chaining is supported by using a Descriptor Pointer register (DMAC_DSCRx) that stores the address in memory of the next buffer descriptor. Each buffer descriptor contains the corresponding buffer descriptor (DMAC_SADDRx, DMAC_DADDRx, DMAC_DSCRx, DMAC_CTRLAx DMAC_CTRLBx). To set up buffer chaining, a sequence of linked lists must be programmed in memory. The DMAC_SADDRx, DMAC_DADDRx, DMAC_DSCRx, DMAC_CTRLAx and DMAC_CTRLBx registers are fetched from system memory on an LLI update. The updated content of the DMAC_CTRLAx register is written back to memory on buffer completion. Figure 34-5 on page 702 shows how to use chained linked lists in memory to define multi-buffer transfers using buffer chaining. The Linked List multi-buffer transfer is initiated by programming DMAC_DSCRx with DSCRx(0) (LLI(0) base address) and DMAC_CTRLBx register with both SRC_DSCR and DST_DSCR set to 0. Other fields and registers are ignored and overwritten when the descriptor is retrieved from memory. The last transfer descriptor must be written to memory with its next descriptor address set to 0. SAM9M11 [DATASHEET] 701 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 34-5. Multi Buffer Transfer Using Linked List System Memory LLI(0) LLI(1) DSCRx(1)= DSCRx(0) + 0x10 DSCRx(2)= DSCRx(1) + 0x10 CTRLBx= DSCRx(0) + 0xC CTRLBx= DSCRx(1) + 0xC CTRLAx= DSCRx(0) + 0x8 CTRLBx= DSCRx(1) + 0x8 DADDRx= DSCRx(0) + 0x4 DADDRx= DSCRx(1) + 0x4 SADDRx= DSCRx(0) + 0x0 SADDRx= DSCRx(1) + 0x0 DSCRx(0) DSCRx(1) DSCRx(2) (points to 0 if LLI(1) is the last transfer descriptor 702 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.5.4.3 Programming DMAC for Multiple Buffer Transfers Table 34-2. Multiple Buffers Transfer Management Table Other Transfer Type AUTO SRC_REP DST_REP SRC_DSCRDST_DSCR BTSIZE SADDR DADDR Fields 1) Single Buffer or Last buffer of 0 – – 1 1 USR(1) a multiple buffer transfer 2) Multi-buffer transfer with 0 – 0 0 1 LLI(5) CONT(2) LLI(5) contiguous DADDR 3) Multi-buffer transfer with 0 0 – 1 0 LLI(5) CONT(2) LLI(5) contiguous SADDR 4) Multi-buffer transfer with 0 – – 0 0 LLI(5) LLI(5) support 5) Multi-buffer transfer with 0 – 1 0 1 LLI(5) REP(3) LLI(5) DADDR reloaded 6) Multi-buffer transfer with 0 1 – 1 0 LLI(5) REP(3) LLI(5) SADDR reloaded 7) Multi-buffer transfer with BTSIZE reloaded and 1 – 0 0 1 REP(3) LLI(5) CONT(2) LLI(5) contiguous DADDR 8) Multi-buffer transfer with BTSIZE reloaded and 1 0 – 1 0 REP(3) CONT(2) LLI(5) contiguous SADDR 9) Automatic mode channel is 1 0 0 1 1 REP(3) CONT(2) REP stalling, BTSIZE is reloaded(4) 10) Automatic mode BTSIZE, 1 1 1 1 1 REP(3) SADDR and DADDR reloaded 11) Automatic mode BTSIZE, SADDR reloaded and DADDR 1 1 0 1 1 REP(3) CONT(2) REP(3) contiguous Notes: 1. USR means that the register field is manually programmed by the user. 2. CONT means that address are contiguous. 3. REP means that the register field is updated with its previous value. If the transfer is the first one, then the user must manually program the value. 4. Channel stalled is true if the relevant BTC interrupt is not masked. 5. LLI means that the register field is updated with the content of the linked list item. 34.5.4.4 Replay Mode of Channel Registers During automatic replay mode, the channel registers are reloaded with their initial values at the completion of each buffer and the new values used for the new buffer. Depending on the row number in Table 34-2, some or all of the DMAC_SADDRx, DMAC_DADDRx, DMAC_CTRLAx and DMAC_CTRLBx channel registers are reloaded from their initial value at the start of a buffer transfer. 34.5.4.5 Contiguous Address Between Buffers In this case, the address between successive buffers is selected to be a continuation from the end of the previous buffer. Enabling the source or destination address to be contiguous between buffers is a function of DMAC_CTRLAx.SRC_DSCR, DMAC_CFGx.SRC_REP, DMAC_CTRLAx.DST_DSCR and DMAC_CFGx.DST_REP registers. SAM9M11 [DATASHEET] 703 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.5.4.6 Suspension of Transfers Between buffers At the end of every buffer transfer, an end of buffer interrupt is asserted if:  the channel buffer interrupt is unmasked, DMAC_EBCIMR.BTC[n] = ‘1’, where n is the channel number. Note: The buffer complete interrupt is generated at the completion of the buffer transfer to the destination. At the end of a chain of multiple buffers, an end of linked list interrupt is asserted if:  the channel end of chained buffer interrupt is unmasked, DMAC_EBCIMR.CBTC[n] = ‘1’, when n is the channel number. 34.5.4.7 Ending Multi-buffer Transfers All multi-buffer transfers must end as shown in Row 1 of Table 34-2 on page 703. At the end of every buffer transfer, the DMAC samples the row number, and if the DMAC is in Row 1 state, then the previous buffer transferred was the last buffer and the DMAC transfer is terminated. For rows 9, 10 and 11 of Table 34-2 on page 703, (DMAC_DSCRx = 0 and DMAC_CTRLBx.AUTO is set), multi- buffer DMAC transfers continue until the automatic mode is disabled by writing a ‘1’ in DMAC_CTRLBx.AUTO bit. This bit should be programmed to zero in the end of buffer interrupt service routine that services the next-to-last buffer transfer. This puts the DMAC into Row 1 state. For rows 2, 3, 4, 5, and 6 (DMAC_CRTLBx.AUTO cleared) the user must setup the last buffer descriptor in memory such that both LLI.DMAC_CTRLBx.SRC_DSCR and LLI.DMAC_CTRLBx.DST_DSCR are one and LLI.DMAC_DSCRx is set to 0. 34.5.5 Programming a Channel Four registers, the DMAC_DSCRx, the DMAC_CTRLAx, the DMAC_CTRLBx and DMAC_CFGx, need to be programmed to set up whether single or multi-buffer transfers take place, and which type of multi-buffer transfer is used. The different transfer types are shown in Table 34-2 on page 703. The “BTSIZE, SADDR and DADDR” columns indicate where the values of DMAC_SARx, DMAC_DARx, DMAC_CTLx, and DMAC_LLPx are obtained for the next buffer transfer when multi-buffer DMAC transfers are enabled. 704 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.5.5.1 Programming Examples 34.5.5.2 Single-buffer Transfer (Row 1) 1. Read the Channel Handler Status Register DMAC_CHSR.ENABLE Field to choose a free (disabled) channel. 2. Clear any pending interrupts on the channel from the previous DMAC transfer by reading the interrupt status register, DMAC_EBCISR. 3. Program the following channel registers: a. Write the starting source address in the DMAC_SADDRx register for channel x. b. Write the starting destination address in the DMAC_DADDRx register for channel x. c. Program DMAC_CTRLAx, DMAC_CTRLBx and DMAC_CFGx according to Row 1 as shown in Table 34-2 on page 703. Program the DMAC_CTRLBx register with both DST_DSCR and SRC_DSCR fields set to one and AUTO field set to 0. d. Write the control information for the DMAC transfer in the DMAC_CTRLAx and DMAC_CTRLBx reg- isters for channel x. For example, in the register, you can program the following: ̶ i. Set up the transfer type (memory or non-memory peripheral for source and destination) and flow control device by programming the FC of the DMAC_CTRLBx register. ̶ ii. Set up the transfer characteristics, such as: – Transfer width for the source in the SRC_WIDTH field. – Transfer width for the destination in the DST_WIDTH field. – Source AHB Master interface layer in the SIF field where source resides. – Destination AHB Master Interface layer in the DIF field where destination resides. – Incrementing/decrementing or fixed address for source in SRC_INC field. – Incrementing/decrementing or fixed address for destination in DST_INC field. e. Write the channel configuration information into the DMAC_CFGx register for channel x. ̶ i. Designate the handshaking interface type (hardware or software) for the source and destination peripherals. This is not required for memory. This step requires programming the SRC_H2SEL/DST_H2SEL bits, respectively. Writing a ‘1’ activates the hardware handshaking interface to handle source/destination requests. Writing a ‘0’ activates the software handshaking interface to handle source/destination requests. ̶ ii. If the hardware handshaking interface is activated for the source or destination peripheral, assign a handshaking interface to the source and destination peripheral. This requires programming the SRC_PER and DST_PER bits, respectively. f. If source picture-in-picture mode is enabled (DMAC_CTRLBx.SRC_PIP is enabled), program the DMAC_SPIPx register for channel x. g. If destination picture-in-picture mode is enabled (DMAC_CTRLBx.DST_PIP is enabled), program the DMAC_DPIPx register for channel x. 4. After the DMAC selected channel has been programmed, enable the channel by writing a ‘1’ to the DMAC_CHER.ENABLE[n] bit, where n is the channel number. Make sure that bit 0 of DMAC_EN.ENABLE register is enabled. 5. Source and destination request single and chunk DMAC transactions to transfer the buffer of data (assuming non-memory peripherals). The DMAC acknowledges at the completion of every transaction (chunk and single) in the buffer and carry out the buffer transfer. 6. Once the transfer completes, hardware sets the interrupts and disables the channel. At this time you can either respond to the buffer Complete or Transfer Complete interrupts, or poll for the Channel Handler Status Register (DMAC_CHSR.ENABLE[n]) bit until it is cleared by hardware, to detect when the transfer is complete. SAM9M11 [DATASHEET] 705 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.5.5.3 Multi-buffer Transfer with Linked List for Source and Linked List for Destination (Row 4) 1. Read the Channel Enable register to choose a free (disabled) channel. 2. Set up the chain of Linked List Items (otherwise known as buffer descriptors) in memory. Write the control information in the LLI.DMAC_CTRLAx and LLI.DMAC_CTRLBx registers location of the buffer descriptor for each LLI in memory (see Figure 34-6 on page 707) for channel x. For example, in the register, you can program the following: a. Set up the transfer type (memory or non-memory peripheral for source and destination) and flow con- trol device by programming the FC of the DMAC_CTRLBx register. b. Set up the transfer characteristics, such as: ̶ i. Transfer width for the source in the SRC_WIDTH field. ̶ ii. Transfer width for the destination in the DST_WIDTH field. ̶ iii. Source AHB master interface layer in the SIF field where source resides. ̶ iv. Destination AHB master interface layer in the DIF field where destination resides. ̶ v. Incrementing/decrementing or fixed address for source in SRC_INCR field. ̶ vi. Incrementing/decrementing or fixed address for destination DST_INCR field. 3. Write the channel configuration information into the DMAC_CFGx register for channel x. a. Designate the handshaking interface type (hardware or software) for the source and destination peripherals. This is not required for memory. This step requires programming the SRC_H2SEL/DST_H2SEL bits, respectively. Writing a ‘1’ activates the hardware handshaking inter- face to handle source/destination requests for the specific channel. Writing a ‘0’ activates the software handshaking interface to handle source/destination requests. b. If the hardware handshaking interface is activated for the source or destination peripheral, assign the handshaking interface to the source and destination peripheral. This requires programming the SRC_PER and DST_PER bits, respectively. 4. Make sure that the LLI.DMAC_CTRLBx register locations of all LLI entries in memory (except the last) are set as shown in Row 4 of Table 34-2 on page 703. The LLI.DMAC_CTRLBx register of the last Linked List Item must be set as described in Row 1 of Table 34-2. Figure 34-5 on page 702 shows a Linked List example with two list items. 5. Make sure that the LLI.DMAC_DSCRx register locations of all LLI entries in memory (except the last) are non-zero and point to the base address of the next Linked List Item. 6. Make sure that the LLI.DMAC_SADDRx/LLI.DMAC_DADDRx register locations of all LLI entries in memory point to the start source/destination buffer address preceding that LLI fetch. 7. Make sure that the LLI.DMAC_CTRLAx.DONE field of the LLI.DMAC_CTRLAx register locations of all LLI entries in memory are cleared. 8. If source picture-picture mode is enabled (DMAC_CTRLBx.SRC_PIP is enabled), program the DMAC_SPIPx register for channel x. 9. If destination picture-in-picture is enabled (DMAC_CTRLBx.DST_PIP is enabled), program the DMAC_DPIPx register for channel x. 10. Clear any pending interrupts on the channel from the previous DMAC transfer by reading the status register: DMAC_EBCISR. 11. Program the DMAC_CTRLBx, DMAC_CFGx registers according to Row 4 as shown in Table 34-2 on page 703. 12. Program the DMAC_DSCRx register with DMAC_DSCRx(0), the pointer to the first Linked List item. 13. Finally, enable the channel by writing a ‘1’ to the DMAC_CHER.ENABLE[n] bit, where n is the channel number. The transfer is performed. 14. The DMAC fetches the first LLI from the location pointed to by DMAC_DSCRx(0). 706 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Note: The LLI.DMAC_SADDRx, LLI. DMAC_DADDRx, LLI.DMAC_DSCRx, LLI.DMAC_CTRLAx and LLI.DMAC_CTRLBx registers are fetched. The DMAC automatically reprograms the DMAC_SADDRx, DMAC_DADDRx, DMAC_DSCRx, DMAC_CTRLBx and DMAC_CTRLAx channel registers from the DMAC_DSCRx(0). 15. Source and destination request single and chunk DMAC transactions to transfer the buffer of data (assuming non-memory peripheral). The DMAC acknowledges at the completion of every transaction (chunk and single) in the buffer and carry out the buffer transfer. 16. Once the buffer of data is transferred, the DMAC_CTRLAx register is written out to system memory at the same location and on the same layer (DMAC_DSCRx.DSCR_IF) where it was originally fetched, that is, the location of the DMAC_CTRLAx register of the linked list item fetched prior to the start of the buffer transfer. Only DMAC_CTRLAx register is written out because only the DMAC_CTRLAx.BTSIZE and DMAC_CTRLAX.DONE bits have been updated by DMAC hardware. Additionally, the DMAC_CTRLAx.DONE bit is asserted when the buffer transfer has completed. Note: Do not poll the DMAC_CTRLAx.DONE bit in the DMAC memory map. Instead, poll the LLI.DMAC_CTRLAx.DONE bit in the LLI for that buffer. If the poll LLI.DMAC_CTRLAx.DONE bit is asserted, then this buffer transfer has completed. This LLI.DMAC_CTRLAx.DONE bit was cleared at the start of the transfer. 17. The DMAC does not wait for the buffer interrupt to be cleared, but continues fetching the next LLI from the memory location pointed to by current DMAC_DSCRx register and automatically reprograms the DMAC_SADDRx, DMAC_DADDRx, DMAC_DSCRx, DMAC_CTRLAx and DMAC_CTRLBx channel registers. The DMAC transfer continues until the DMAC determines that the DMAC_CTRLBx and DMAC_DSCRx registers at the end of a buffer transfer match described in Row 1 of Table 34-2 on page 703. The DMAC then knows that the previous buffer transferred was the last buffer in the DMAC transfer. The DMAC transfer might look like that shown in Figure 34-6. Figure 34-6. Multi-buffer with Linked List Address for Source and Destination Address of Address of Source Layer Destination Layer Buffer 2 Buffer 2 SADDR(2) DADDR(2) Buffer 1 Buffer 1 SADDR(1) DADDR(1) Buffer 0 Buffer 0 DADDR(0) SADDR(0) Source Buffers Destination Buffers If the user needs to execute a DMAC transfer where the source and destination address are contiguous but the amount of data to be transferred is greater than the maximum buffer size DMAC_CTRLAx.BTSIZE, then this can be achieved using the type of multi-buffer transfer as shown in Figure 34-7. SAM9M11 [DATASHEET] 707 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 34-7. Multi-buffer with Linked Address for Source and Destination Buffers are Contiguous Address of Address of Source Layer Destination Layer Buffer 2 DADDR(3) Buffer 2 Buffer 2 SADDR(3) DADDR(2) Buffer 2 Buffer 1 SADDR(2) DADDR(1) Buffer 1 Buffer 0 SADDR(1) DADDR(0) Buffer 0 SADDR(0) Source Buffers Destination Buffers The DMAC transfer flow is shown in Figure 34-8 on page 709. 708 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 34-8. DMAC Transfer Flow for Source and Destination Linked List Address Channel enabled by software LLI Fetch Hardware reprograms SADDRx, DADDRx, CTRLA/Bx, DSCRx DMAC buffer transfer Writeback of HDMA_CTRLAx register in system memory Buffer Complete interrupt generated here Is HDMA in Row1 of no HDMA State Machine Table? HDMA Transfer Complete yes interrupt generated here Channel Disabled by hardware SAM9M11 [DATASHEET] 709 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.5.5.4 Multi-buffer Transfer with Source Address Auto-reloaded and Destination Address Auto-reloaded (Row 10) 1. Read the Channel Enable register to choose an available (disabled) channel. 2. Clear any pending interrupts on the channel from the previous DMAC transfer by reading the interrupt status register. Program the following channel registers: a. Write the starting source address in the DMAC_SADDRx register for channel x. b. Write the starting destination address in the DMAC_DADDRx register for channel x. c. Program DMAC_CTRLAx, DMAC_CTRLBx and DMAC_CFGx according to Row 10 as shown in Table 34-2 on page 703. Program the DMAC_DSCRx register with ‘0’. d. Write the control information for the DMAC transfer in the DMAC_CTRLAx and DMAC_CTRLBx reg- ister for channel x. For example, in the register, you can program the following: ̶ i. Set up the transfer type (memory or non-memory peripheral for source and destination) and flow control device by programming the FC of the DMAC_CTRLBx register. ̶ ii. Set up the transfer characteristics, such as: – Transfer width for the source in the SRC_WIDTH field. – Transfer width for the destination in the DST_WIDTH field. – Source AHB master interface layer in the SIF field where source resides. – Destination AHB master interface layer in the DIF field where destination resides. – Incrementing/decrementing or fixed address for source in SRC_INCR field. – Incrementing/decrementing or fixed address for destination in DST_INCR field. e. If source picture-in-picture mode is enabled (DMAC_CTRLBx.SPIP is enabled), program the DMAC_SPIPx register for channel x. f. If destination picture-in-picture is enabled (DMAC_CTRLBx.DPIP), program the DMAC_DPIPx regis- ter for channel x. g. Write the channel configuration information into the DMAC_CFGx register for channel x. Ensure that the reload bits, DMAC_CFGx.SRC_REP, DMAC_CFGx.DST_REP and DMAC_CTRLBx.AUTO are enabled. ̶ i. Designate the handshaking interface type (hardware or software) for the source and destination peripherals. This is not required for memory. This step requires programming the SRC_H2SEL/DST_h2SEL bits, respectively. Writing a ‘1’ activates the hardware handshaking interface to handle source/destination requests for the specific channel. Writing a ‘0’ activates the software handshaking interface to handle source/destination requests. ̶ ii. If the hardware handshaking interface is activated for the source or destination peripheral, assign handshaking interface to the source and destination peripheral. This requires programming the SRC_PER and DST_PER bits, respectively. 3. After the DMAC selected channel has been programmed, enable the channel by writing a ‘1’ to the DMAC_CHER.ENABLE[n] bit where is the channel number. Make sure that bit 0 of the DMAC_EN register is enabled. 4. Source and destination request single and chunk DMAC transactions to transfer the buffer of data (assuming non-memory peripherals). The DMAC acknowledges on completion of each chunk/single transaction and carry out the buffer transfer. 5. When the buffer transfer has completed, the DMAC reloads the DMAC_SADDRx, DMAC_DADDRx and DMAC_CTRLAx registers. Hardware sets the buffer Complete interrupt. The DMAC then samples the row number as shown in Table 34-2 on page 703. If the DMAC is in Row 1, then the DMAC transfer has completed. Hardware sets the transfer complete interrupt and disables the channel. So you can either respond to the Buffer Complete or Chained buffer transfer Complete interrupts, or poll for the Channel Enable in the Channel Status Register (DMAC_CHSR.ENABLE[n]) until it is disabled, to detect when the transfer is complete. If the DMAC is not in Row 1, the next step is performed. 710 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

6. The DMAC transfer proceeds as follows: a. If interrupts is un-masked (DMAC_EBCIMR.BTC[x] = ‘1’, where x is the channel number) hardware sets the buffer complete interrupt when the buffer transfer has completed. It then stalls until the STALLED[n] bit of DMAC_CHSR is cleared by software, writing ‘1’ to DMAC_CHER.KEEPON[n] bit where n is the channel number. If the next buffer is to be the last buffer in the DMAC transfer, then the buffer complete ISR (interrupt service routine) should clear the automatic mode bit in the DMAC_CTRLBx.AUTO bit. This put the DMAC into Row 1 as shown in Table 34-2 on page 703. If the next buffer is not the last buffer in the DMAC transfer, then the reload bits should remain enabled to keep the DMAC in Row 4. b. If the buffer complete interrupt is masked (DMAC_EBCIMR.BTC[x] = ‘1’, where x is the channel num- ber), then hardware does not stall until it detects a write to the buffer complete interrupt enable register DMAC_EBCIER but starts the next buffer transfer immediately. In this case software must clear the automatic mode bit in the DMAC_CTRLB to put the DMAC into ROW 1 of Table 34-2 on page 703 before the last buffer of the DMAC transfer has completed. The transfer is similar to that shown in Figure 34-9. The DMAC transfer flow is shown in Figure 34-10 on page 712. Figure 34-9. Multi-buffer DMAC Transfer with Source and Destination Address Auto-reloaded Address of Address of Source Layer Destination Layer Block0 Block1 Block2 SADDR DADDR BlockN Source Buffers Destination Buffers SAM9M11 [DATASHEET] 711 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 34-10. DMAC Transfer Flow for Source and Destination Address Auto-reloaded Channel Enabled by software Buffer Transfer Replay mode for SADDRx, DADDRx, CTRLAx, CTRLBx Buffer Complete interrupt generated here HDMA Transfer Complete Interrupt generated here yes Is HDMA in Row1 of HDMA State Machine table? Channel Disabled by hardware no no EBCIMR[x]=1? yes Stall until STALLED is cleared by writing to KEEPON field 34.5.5.5 Multi-buffer Transfer with Source Address Auto-reloaded and Linked List Destination Address (Row 6) 1. Read the Channel Enable register to choose a free (disabled) channel. 2. Set up the chain of linked list items (otherwise known as buffer descriptors) in memory. Write the control information in the LLI.DMAC_CTRLAx and DMAC_CTRLBx registers location of the buffer descriptor for each LLI in memory for channel x. For example, in the register you can program the following: a. Set up the transfer type (memory or non-memory peripheral for source and destination) and flow con- trol peripheral by programming the FC of the DMAC_CTRLBx register. b. Set up the transfer characteristics, such as: ̶ i. Transfer width for the source in the SRC_WIDTH field. ̶ ii. Transfer width for the destination in the DST_WIDTH field. ̶ iii. Source AHB master interface layer in the SIF field where source resides. ̶ iv. Destination AHB master interface layer in the DIF field where destination resides. ̶ v. Incrementing/decrementing or fixed address for source in SRC_INCR field. ̶ vi. Incrementing/decrementing or fixed address for destination DST_INCR field. 3. Write the starting source address in the DMAC_SADDRx register for channel x. Note: The values in the LLI.DMAC_SADDRx register locations of each of the Linked List Items (LLIs) setup up in memory, although fetched during a LLI fetch, are not used. 712 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

4. Write the channel configuration information into the DMAC_CFGx register for channel x. a. Designate the handshaking interface type (hardware or software) for the source and destination peripherals. This is not required for memory. This step requires programming the SRC_H2SEL/DST_H2SEL bits, respectively. Writing a ‘1’ activates the hardware handshaking inter- face to handle source/destination requests for the specific channel. Writing a ‘0’ activates the software handshaking interface source/destination requests. b. If the hardware handshaking interface is activated for the source or destination peripheral, assign handshaking interface to the source and destination peripheral. This requires programming the SRC_PER and DST_PER bits, respectively. 5. Make sure that the LLI.DMAC_CTRLBx register locations of all LLIs in memory (except the last) are set as shown in Row 6 of Table 34-2 on page 703 while the LLI.DMAC_CTRLBx register of the last Linked List item must be set as described in Row 1 of Table 34-2. Figure 34-5 on page 702 shows a Linked List example with two list items. 6. Make sure that the LLI.DMAC_DSCRx register locations of all LLIs in memory (except the last) are non-zero and point to the next Linked List Item. 7. Make sure that the LLI.DMAC_DADDRx register location of all LLIs in memory point to the start destination buffer address proceeding that LLI fetch. 8. Make sure that the LLI.DMAC_CTLx.DONE field of the LLI.DMAC_CTRLA register locations of all LLIs in memory is cleared. 9. If source picture-in-picture is enabled (DMAC_CTRLBx.SPIP is enabled), program the DMAC_SPIPx register for channel x. 10. If destination picture-in-picture is enabled (DMAC_CTRLBx.DPIP is enabled), program the DMAC_DPIPx register for channel x. 11. Clear any pending interrupts on the channel from the previous DMAC transfer by reading to the DMAC_EBCISR. 12. Program the DMAC_CTLx, DMAC_CFGx registers according to Row 6 as shown in Table 34-2 on page 703. 13. Program the DMAC_DSCRx register with DMAC_DSCRx(0), the pointer to the first Linked List item. 14. Finally, enable the channel by writing a ‘1’ to the DMAC_CHER.ENABLE[n] bit where n is the channel number. The transfer is performed. Make sure that bit 0 of the DMAC_EN register is enabled. 15. The DMAC fetches the first LLI from the location pointed to by DMAC_DSCRx(0). Note: The LLI.DMAC_SADDRx, LLI.DMAC_DADDRx, LLI. DMAC_LLPx LLI.DMAC_CTRLAx and LLI.DMAC_CTRLBx registers are fetched. The LLI.DMAC_SADDRx register although fetched is not used. 16. Source and destination request single and chunk DMAC transactions to transfer the buffer of data (assuming non-memory peripherals). DMAC acknowledges at the completion of every transaction (chunk and single) in the buffer and carry out the buffer transfer. 17. The DMAC_CTRLAx register is written out to system memory. The DMAC_CTRLAx register is written out to the same location on the same layer (DMAC_DSCRx.DSCR_IF) where it was originally fetched, that is the location of the DMAC_CTRLAx register of the linked list item fetched prior to the start of the buffer transfer. Only DMAC_CTRLAx register is written out, because only the DMAC_CTRLAx.BTSIZE and DMAC_CTRLAx.DONE fields have been updated by hardware within the DMAC. The LLI.DMAC_CTRLAx.DONE bit is asserted to indicate buffer completion Therefore, software can poll the LLI.DMAC_CTRLAx.DONE field of the DMAC_CTRLAx register in the LLi to ascertain when a buffer transfer has completed. Note: Do not poll the DMAC_CTRLAx.DONE bit in the DMAC memory map. Instead poll the LLI.DMAC_CTRLAx.DONE bit in the LLI for that buffer. If the polled LLI.DMAC_CTRLAx.DONE bit is asserted, then this buffer transfer has completed. This LLI.DMAC_CTRLA.DONE bit was cleared at the start of the transfer. 18. The DMAC reloads the DMAC_SADDRx register from the initial value. Hardware sets the buffer complete interrupt. The DMAC samples the row number as shown in Table 34-2 on page 703. If the DMAC is in Row 1, then the DMAC transfer has completed. Hardware sets the transfer complete interrupt and disables the SAM9M11 [DATASHEET] 713 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

channel. You can either respond to the Buffer Complete or Chained buffer Transfer Complete interrupts, or poll for the Channel Enable (DMAC_CHSR.ENABLE) bit until it is cleared by hardware, to detect when the transfer is complete. If the DMAC is not in Row 1 as shown in Table 34-2 on page 703, the following step is performed. 19. The DMAC fetches the next LLI from memory location pointed to by the current DMAC_DSCRx register, and automatically reprograms the DMAC_DADDRx, DMAC_CTRLAx, DMAC_CTRLBx and DMAC_DSCRx channel registers. Note that the DMAC_SADDRx is not re-programmed as the reloaded value is used for the next DMAC buffer transfer. If the next buffer is the last buffer of the DMAC transfer then the DMAC_CTRLBx and DMAC_DSCRx registers just fetched from the LLI should match Row 1 of Table 34-2 on page 703. The DMAC transfer might look like that shown in Figure 34-11. Figure 34-11. Multi-buffer DMAC Transfer with Source Address Auto-reloaded and Linked List Destination Address Address of Address of Source Layer Destination Layer Buffer0 DADDR(0) Buffer1 DADDR(1) SADDR Buffer2 DADDR(2) BufferN DADDR(N) Source Buffers Destination Buffers The DMAC Transfer flow is shown in Figure 34-12 on page 715. 714 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 34-12. DMAC Transfer Flow for Replay Mode at Source and Linked List Destination Address Channel Enabled by software LLI Fetch Hardware reprograms DADDRx, CTRLAx, CTRLBx, DSCRx DMA buffer transfer Writeback of control status information in LLI Reload SADDRx Buffer Complete interrupt generated here Is HDMA in yes Row1 of HDMA Transfer Complete HDMA State Machine Table? interrupt generated here Channel Disabled by no hardware 34.5.5.6 Multi-buffer Transfer with Source Address Auto-reloaded and Contiguous Destination Address (Row 11) 1. Read the Channel Enable register to choose a free (disabled) channel. 2. Clear any pending interrupts on the channel from the previous DMAC transfer by reading to the Interrupt Status Register. 3. Program the following channel registers: a. Write the starting source address in the DMAC_SADDRx register for channel x. b. Write the starting destination address in the DMAC_DADDRx register for channel x. c. Program DMAC_CTRLAx, DMAC_CTRLBx and DMAC_CFGx according to Row 11 as shown in Table 34-2 on page 703. Program the DMAC_DSCRx register with ‘0’. DMAC_CTRLBx.AUTO field is set to ‘1’ to enable automatic mode support. d. Write the control information for the DMAC transfer in the DMAC_CTRLBx and DMAC_CTRLAx reg- ister for channel x. For example, in this register, you can program the following: ̶ i. Set up the transfer type (memory or non-memory peripheral for source and destination) and flow control device by programming the FC of the DMAC_CTRLBx register. ̶ ii. Set up the transfer characteristics, such as: – Transfer width for the source in the SRC_WIDTH field. – Transfer width for the destination in the DST_WIDTH field. – Source AHB master interface layer in the SIF field where source resides. – Destination AHB master interface master layer in the DIF field where destination resides. SAM9M11 [DATASHEET] 715 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

– Incrementing/decrementing or fixed address for source in SRC_INCR field. – Incrementing/decrementing or fixed address for destination in DST_INCR field. e. If source picture-in-picture is enabled (DMAC_CTRLBx.SPIP is enabled), program the DMAC_SPIPx register for channel x. f. If destination picture-in-picture is enabled (DMAC_CTRLBx.DPIP), program the DMAC_DPIPx regis- ter for channel x. g. Write the channel configuration information into the DMAC_CFGx register for channel x. ̶ i. Designate the handshaking interface type (hardware or software) for the source and destination peripherals. This is not required for memory. This step requires programming the SRC_H2SEL/DST_H2SEL bits, respectively. Writing a ‘1’ activates the hardware handshaking interface to handle source/destination requests for the specific channel. Writing a ‘0’ activates the software handshaking interface to handle source/destination requests. ̶ ii. If the hardware handshaking interface is activated for the source or destination peripheral, assign handshaking interface to the source and destination peripheral. This requires programming the SRC_PER and DST_PER bits, respectively. 4. After the DMAC channel has been programmed, enable the channel by writing a ‘1’ to the DMAC_CHER.ENABLE[n] bit where n is the channel number. Make sure that bit 0 of the DMAC_EN.ENABLE register is enabled. 5. Source and destination request single and chunk DMAC transactions to transfer the buffer of data (assuming non-memory peripherals). The DMAC acknowledges at the completion of every transaction (chunk and single) in the buffer and carries out the buffer transfer. 6. When the buffer transfer has completed, the DMAC reloads the DMAC_SADDRx register. The DMAC_DADDRx register remains unchanged. Hardware sets the buffer complete interrupt. The DMAC then samples the row number as shown in Table 34-2 on page 703. If the DMAC is in Row 1, then the DMAC transfer has completed. Hardware sets the transfer complete interrupt and disables the channel. So you can either respond to the Buffer Complete or Transfer Complete interrupts, or poll for ENABLE field in the Channel Status Register (DMAC_CHSR.ENABLE[n] bit) until it is cleared by hardware, to detect when the transfer is complete. If the DMAC is not in Row 1, the next step is performed. 7. The DMAC transfer proceeds as follows: a. If the buffer complete interrupt is un-masked (DMAC_EBCIMR.BTC[x] = ‘1’, where x is the channel number) hardware sets the buffer complete interrupt when the buffer transfer has completed. It then stalls until STALLED[n] bit of DMAC_CHSR is cleared by writing in the KEEPON[n] field of DMAC_CHER where n is the channel number. If the next buffer is to be the last buffer in the DMAC transfer, then the buffer complete ISR (interrupt service routine) should clear the automatic mode bit, DMAC_CTRLBx.AUTO. This puts the DMAC into Row 1 as shown in Table 34-2 on page 703. If the next buffer is not the last buffer in the DMAC transfer then the automatic transfer mode bit should remain enabled to keep the DMAC in Row 11 as shown in Table 34-2 on page 703. b. If the buffer complete interrupt is masked (DMAC_EBCIMR.BTC[x] = ‘1’, where x is the channel num- ber) then hardware does not stall until it detects a write to the buffer transfer completed interrupt enable register but starts the next buffer transfer immediately. In this case software must clear the automatic mode bit, DMAC_CTRLBx.AUTO, to put the device into ROW 1 of Table 34-2 on page 703 before the last buffer of the DMAC transfer has completed. The transfer is similar to that shown in Figure 34-13 on page 717. The DMAC Transfer flow is shown in Figure 34-14 on page 718. 716 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 34-13. Multi-buffer Transfer with Source Address Auto-reloaded and Contiguous Destination Address Address of Address of Source Layer Destination Layer Buffer2 DADDR(2) Buffer1 DADDR(1) Buffer0 SADDR DADDR(0) Source Buffers Destination Buffers SAM9M11 [DATASHEET] 717 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 34-14. DMAC Transfer Replay Mode is Enabled for the Source and Contiguous Destination Address Channel Enabled by software Buffer Transfer Replay mode for SADDRx, Contiguous mode for DADDRx CTRLAx, CTRLBx Buffer Complete interrupt generated here Buffer Transfer Complete interrupt generated here yes Is HDMA in Row1of HDMA State Machine Table? Channel Disabled by no hardware no DMA_EBCIMR[x]=1? yes Stall until STALLED field is cleared by software writing KEEPON Field 34.5.5.7 Multi-buffer DMAC Transfer with Linked List for Source and Contiguous Destination Address (Row 2) 1. Read the Channel Enable register to choose a free (disabled) channel. 2. Set up the linked list in memory. Write the control information in the LLI.DMAC_CTRLAx and LLI.DMAC_CTRLBx register location of the buffer descriptor for each LLI in memory for channel x. For example, in the register, you can program the following: a. Set up the transfer type (memory or non-memory peripheral for source and destination) and flow con- trol device by programming the FC of the DMAC_CTRLBx register. b. Set up the transfer characteristics, such as: ̶ i. Transfer width for the source in the SRC_WIDTH field. ̶ ii. Transfer width for the destination in the DST_WIDTH field. ̶ iii. Source AHB master interface layer in the SIF field where source resides. ̶ iv. Destination AHB master interface layer in the DIF field where destination resides. ̶ v. Incrementing/decrementing or fixed address for source in SRC_INCR field. ̶ vi. Incrementing/decrementing or fixed address for destination DST_INCR field. 3. Write the starting destination address in the DMAC_DADDRx register for channel x. 718 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Note: The values in the LLI.DMAC_DADDRx register location of each Linked List Item (LLI) in memory, although fetched during an LLI fetch, are not used. 4. Write the channel configuration information into the DMAC_CFGx register for channel x. a. Designate the handshaking interface type (hardware or software) for the source and destination peripherals. This is not required for memory. This step requires programming the SRC_H2SEL/DST_H2SEL bits, respectively. Writing a ‘1’ activates the hardware handshaking inter- face to handle source/destination requests for the specific channel. Writing a ‘0’ activates the software handshaking interface to handle source/destination requests. b. If the hardware handshaking interface is activated for the source or destination peripheral, assign handshaking interface to the source and destination peripherals. This requires programming the SRC_PER and DST_PER bits, respectively. 5. Make sure that all LLI.DMAC_CTRLBx register locations of the LLI (except the last) are set as shown in Row 2 of Table 34-2 on page 703, while the LLI.DMAC_CTRLBx register of the last Linked List item must be set as described in Row 1 of Table 34-2. Figure 34-5 on page 702 shows a Linked List example with two list items. 6. Make sure that the LLI.DMAC_DSCRx register locations of all LLIs in memory (except the last) are non-zero and point to the next Linked List Item. 7. Make sure that the LLI.DMAC_SADDRx register location of all LLIs in memory point to the start source buffer address proceeding that LLI fetch. 8. Make sure that the LLI.DMAC_CTRLAx.DONE field of the LLI.DMAC_CTRLAx register locations of all LLIs in memory is cleared. 9. If source picture-in-picture is enabled (DMAC_CTRLBx.SPIP is enabled), program the DMAC_SPIPx register for channel x. 10. If destination picture-in-picture is enabled (DMAC_CTRLBx.DPIP is enabled), program the DMAC_DPIPx register for channel x. 11. Clear any pending interrupts on the channel from the previous DMAC transfer by reading the interrupt status register. 12. Program the DMAC_CTRLAx, DMAC_CTRLBx and DMAC_CFGx registers according to Row 2 as shown in Table 34-2 on page 703 13. Program the DMAC_DSCRx register with DMAC_DSCRx(0), the pointer to the first Linked List item. 14. Finally, enable the channel by writing a ‘1’ to the DMAC_CHER.ENABLE[n] bit. The transfer is performed. Make sure that bit 0 of the DMAC_EN register is enabled. 15. The DMAC fetches the first LLI from the location pointed to by DMAC_DSCRx(0). Note: The LLI.DMAC_SADDRx, LLI.DMAC_DADDRx, LLI.DMAC_DSCRx and LLI.DMAC_CTRLA/Bx registers are fetched. The LLI.DMAC_DADDRx register location of the LLI although fetched is not used. The DMAC_DADDRx register in the DMAC remains unchanged. 16. Source and destination requests single and chunk DMAC transactions to transfer the buffer of data (assuming non-memory peripherals). The DMAC acknowledges at the completion of every transaction (chunk and single) in the buffer and carry out the buffer transfer 17. Once the buffer of data is transferred, the DMAC_CTRLAx register is written out to system memory at the same location and on the same layer (DMAC_DSCRx.DSCR_IF) where it was originally fetched, that is, the location of the DMAC_CTRLAx register of the linked list item fetched prior to the start of the buffer transfer. Only DMAC_CTRLAx register is written out because only the DMAC_CTRLAx.BTSIZE and DMAC_CTRLAX.DONE fields have been updated by DMAC hardware. Additionally, the DMAC_CTRLAx.DONE bit is asserted when the buffer transfer has completed. Note: Do not poll the DMAC_CTRLAx.DONE bit in the DMAC memory map. Instead, poll the LLI.DMAC_CTRLAx.DONE bit in the LLI for that buffer. If the poll LLI.DMAC_CTRLAx.DONE bit is asserted, then this buffer transfer has completed. This LLI.DMAC_CTRLAx.DONE bit was cleared at the start of the transfer. SAM9M11 [DATASHEET] 719 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

18. The DMAC does not wait for the buffer interrupt to be cleared, but continues and fetches the next LLI from the memory location pointed to by current DMAC_DSCRx register and automatically reprograms the DMAC_SADDRx, DMAC_CTRLAx, DMAC_CTRLBx and DMAC_DSCRx channel registers. The DMAC_DADDRx register is left unchanged. The DMAC transfer continues until the DMAC samples the DMAC_CTRLAx, DMAC_CTRLBx and DMAC_DSCRx registers at the end of a buffer transfer match that described in Row 1 of Table 34-2 on page 703. The DMAC then knows that the previous buffer transferred was the last buffer in the DMAC transfer. The DMAC transfer might look like that shown in Figure 34-15 Note that the destination address is decrementing. Figure 34-15. DMAC Transfer with Linked List Source Address and Contiguous Destination Address Address of Address of Source Layer Destination Layer Buffer 2 SADDR(2) Buffer 2 DADDR(2) Buffer 1 Buffer 1 SADDR(1) DADDR(1) Buffer 0 DADDR(0) Buffer 0 SADDR(0) Source Buffers Destination Buffers The DMAC transfer flow is shown in Figure 34-16 on page 721. 720 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 34-16. DMAC Transfer Flow for Linked List Source Address and Contiguous Destination Address Channel Enabled by software LLI Fetch Hardware reprograms SADDRx, CTRLAx,CTRLBx, DSCRx HDMA buffer transfer Writeback of control information of LLI Buffer Complete interrupt generated here no Is HDMA in Row 1 ? HDMA Transfer Complete yes interrupt generated here Channel Disabled by hardware SAM9M11 [DATASHEET] 721 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.5.6 Disabling a Channel Prior to Transfer Completion Under normal operation, software enables a channel by writing a ‘1’ to the Channel Handler Enable Register, DMAC_CHER.ENABLE[n], and hardware disables a channel on transfer completion by clearing the DMAC_CHSR.ENABLE[n] register bit. The recommended way for software to disable a channel without losing data is to use the SUSPEND[n] bit in conjunction with the EMPTY[n] bit in the Channel Handler Status Register. 1. If software wishes to disable a channel n prior to the DMAC transfer completion, then it can set the DMAC_CHER.SUSPEND[n] bit to tell the DMAC to halt all transfers from the source peripheral. Therefore, the channel FIFO receives no new data. 2. Software can now poll the DMAC_CHSR.EMPTY[n] bit until it indicates that the channel n FIFO is empty, where n is the channel number. 3. The DMAC_CHER.ENABLE[n] bit can then be cleared by software once the channel n FIFO is empty, where n is the channel number. When DMAC_CTRLAx.SRC_WIDTH is less than DMAC_CTRLAx.DST_WIDTH and the DMAC_CHSRx.SUSPEND[n] bit is high, the DMAC_CHSRx.EMPTY[n] is asserted once the contents of the FIFO do not permit a single word of DMAC_CTRLAx.DST_WIDTH to be formed. However, there may still be data in the channel FIFO but not enough to form a single transfer of DMAC_CTLx.DST_WIDTH width. In this configuration, once the channel is disabled, the remaining data in the channel FIFO are not transferred to the destination peripheral. It is permitted to remove the channel from the suspension state by writing a ‘1’ to the DMAC_CHER.RESUME[n] field register. The DMAC transfer completes in the normal manner. n defines the channel number. Note: If a channel is disabled by software, an active single or chunk transaction is not guaranteed to receive an acknowledgement. 34.5.6.1 Abnormal Transfer Termination A DMAC transfer may be terminated abruptly by software by clearing the channel enable bit, DMAC_CHDR.ENABLE[n] where n is the channel number. This does not mean that the channel is disabled immediately after the DMAC_CHSR.ENABLE[n] bit is cleared over the APB interface. Consider this as a request to disable the channel. The DMAC_CHSR.ENABLE[n] must be polled and then it must be confirmed that the channel is disabled by reading back 0. Software may terminate all channels abruptly by clearing the global enable bit in the DMAC Configuration Register (DMAC_EN.ENABLE bit). Again, this does not mean that all channels are disabled immediately after the DMAC_EN.ENABLE is cleared over the APB slave interface. Consider this as a request to disable all channels. The DMAC_CHSR.ENABLE must be polled and then it must be confirmed that all channels are disabled by reading back ‘0’. Note: If the channel enable bit is cleared while there is data in the channel FIFO, this data is not sent to the destination peripheral and is not present when the channel is re-enabled. For read sensitive source peripherals, such as a source FIFO, this data is therefore lost. When the source is not a read sensitive device (i.e., memory), disabling a channel without waiting for the channel FIFO to empty may be acceptable as the data is available from the source peripheral upon request and is not lost. Note: If a channel is disabled by software, an active single or chunk transaction is not guaranteed to receive an acknowledgement. 722 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.6 DMAC Software Requirements  There must not be any write operation to Channel registers in an active channel after the channel enable is made HIGH. If any channel parameters must be reprogrammed, this can only be done after disabling the DMAC channel.  When destination peripheral is defined as the flow controller, source single transfer request are not serviced until Destination Peripheral has asserted its Last Transfer Flag.  When Source Peripheral is flow controller, destination single transfer request are not serviced until Source Peripheral has asserted its Last Transfer Flag.  When destination peripheral is defined as the flow controller, if the destination width is smaller than the source width, then a data loss may occur, and the loss is equal to Source Single Transfer size in bytes- destination Single Transfer size in bytes.  When a Memory to Peripheral transfer occurs if the destination peripheral is flow controller, then a prefetch operation is performed. It means that data are extracted from memory before any request from the peripheral is generated.  You must program the DMAC_SADDRx and DMAC_DADDRx channel registers with a byte, half-word and word aligned address depending on the source width and destination width.  After the software disables a channel by writing into the channel disable register, it must re-enable the channel only after it has polled a 0 in the corresponding channel enable status register. This is because the current AHB Burst must terminate properly.  If you program the BTSIZE field in the DMAC_CTRLA, as zero, and the DMAC is defined as the flow controller, then the channel is automatically disabled.  When hardware handshaking interface protocol is fully implemented, a peripheral is expected to deassert any sreq or breq signals on receiving the ack signal irrespective of the request the ack was asserted in response to.  Multiple Transfers involving the same peripheral must not be programmed and enabled on different channel, unless this peripheral integrates several hardware handshaking interface.  When a Peripheral is flow controller, the targeted DMAC Channel must be enabled before the Peripheral. If you do not ensure this the DMAC Channel might miss a Last Transfer Flag, if the First DMAC request is also the last transfer.  When AUTO Field is set to TRUE, then the BTSIZE Field is automatically reloaded from its previous value. BTSIZE must be initialized to a non zero value if the first transfer is initiated with AUTO field set to TRUE even if LLI mode is enabled because the LLI fetch operation will not update this field. SAM9M11 [DATASHEET] 723 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7 DMA Controller (DMAC) User Interface Table 34-3. Register Mapping Offset Register Name Access Reset 0x000 DMAC Global Configuration Register DMAC_GCFG Read/Write 0x10 0x004 DMAC Enable Register DMAC_EN Read/Write 0x0 0x008 DMAC Software Single Request Register DMAC_SREQ Read/Write 0x0 DMAC Software Chunk Transfer Request 0x00C DMAC_CREQ Read/Write 0x0 Register 0x010 DMAC Software Last Transfer Flag Register DMAC_LAST Read/Write 0x0 0x014 Reserved – – – DMAC Error, Chained Buffer transfer completed 0x018 and Buffer transfer completed Interrupt Enable DMAC_EBCIER Write-only – register DMAC Error, Chained Buffer transfer completed 0x01C and Buffer transfer completed Interrupt Disable DMAC_EBCIDR Write-only – register DMAC Error, Chained Buffer transfer completed 0x020 DMAC_EBCIMR Read-only 0x0 and Buffer transfer completed Mask Register DMAC Error, Chained Buffer transfer completed 0x024 DMAC_EBCISR Read-only 0x0 and Buffer transfer completed Status Register 0x028 DMAC Channel Handler Enable Register DMAC_CHER Write-only – 0x02C DMAC Channel Handler Disable Register DMAC_CHDR Write-only – 0x030 DMAC Channel Handler Status Register DMAC_CHSR Read-only 0x00FF0000 0x034 Reserved – – – 0x038 Reserved – – – 0x03C+ch_num*(0x28)+(0x0) DMAC Channel Source Address Register DMAC_SADDR Read/Write 0x0 0x03C+ch_num*(0x28)+(0x4) DMAC Channel Destination Address Register DMAC_DADDR Read/Write 0x0 0x03C+ch_num*(0x28)+(0x8) DMAC Channel Descriptor Address Register DMAC_DSCR Read/Write 0x0 0x03C+ch_num*(0x28)+(0xC) DMAC Channel Control A Register DMAC_CTRLA Read/Write 0x0 0x03C+ch_num*(0x28)+(0x10) DMAC Channel Control B Register DMAC_CTRLB Read/Write 0x0 0x03C+ch_num*(0x28)+(0x14) DMAC Channel Configuration Register DMAC_CFG Read/Write 0x01000000 DMAC Channel Source Picture in Picture 0x03C+ch_num*(0x28)+(0x18) DMAC_SPIP Read/Write 0x0 Configuration Register DMAC Channel Destination Picture in Picture 0x03C+ch_num*(0x28)+(0x1C) DMAC_DPIP Read/Write 0x0 Configuration Register 0x03C+ch_num*(0x28)+(0x20) Reserved – – – 0x03C+ch_num*(0x28)+(0x24) Reserved – – – 0x064–0x140 DMAC Channel 1 to 7 Register(1) Read/Write 0x0 0x017C–0x1FC Reserved – – – Note: 1. The addresses for the DMAC registers shown here are for DMA Channel 0. This sequence of registers is repeated successively for each DMA channel located between 0x064 and 0x140. 724 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.1 DMAC Global Configuration Register Name: DMAC_GCFG Address: 0xFFFFEC00 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – ARB_CFG – – – – Note: Bit fields 0, 1, 2, 3, have a default value of 0. This should not be changed. • ARB_CFG 0: Fixed priority arbiter. 1: Modified round robin arbiter. SAM9M11 [DATASHEET] 725 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.2 DMAC Enable Register Name: DMAC_EN Address: 0xFFFFEC04 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – ENABLE • ENABLE 0: DMA Controller is disabled. 1: DMA Controller is enabled. 726 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.3 DMAC Software Single Request Register Name: DMAC_SREQ Address: 0xFFFFEC08 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 DSREQ7 SSREQ7 DSREQ6 SSREQ6 DSREQ5 SSREQ5 DSREQ4 SSREQ4 7 6 5 4 3 2 1 0 DSREQ3 SSREQ3 DSREQ2 SSREQ2 DSREQ1 SSREQ1 DSREQ0 SSREQ0 • DSREQx Request a destination single transfer on channel i. • SSREQx Request a source single transfer on channel i. SAM9M11 [DATASHEET] 727 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.4 DMAC Software Chunk Transfer Request Register Name: DMAC_CREQ Address: 0xFFFFEC0C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 DCREQ7 SCREQ7 DCREQ6 SCREQ6 DCREQ5 SCREQ5 DCREQ4 SCREQ4 7 6 5 4 3 2 1 0 DCREQ3 SCREQ3 DCREQ2 SCREQ2 DCREQ1 SCREQ1 DCREQ0 SCREQ0 • DCREQx Request a destination chunk transfer on channel i. • SCREQx Request a source chunk transfer on channel i. 728 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.5 DMAC Software Last Transfer Flag Register Name: DMAC_LAST Address: 0xFFFFEC10 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 DLAST7 SLAST7 DLAST6 SLAST6 DLAST5 SLAST5 DLAST4 SLAST4 7 6 5 4 3 2 1 0 DLAST3 SLAST3 DLAST2 SLAST2 DLAST1 SLAST1 DLAST0 SLAST0 • DLASTx Writing one to DLASTx prior to writing one to DSREQx or DCREQx indicates that this destination request is the last trans- fer of the buffer. • SLASTx Writing one to SLASTx prior to writing one to SSREQx or SCREQx indicates that this source request is the last transfer of the buffer. SAM9M11 [DATASHEET] 729 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.6 DMAC Error, Buffer Transfer and Chained Buffer Transfer Interrupt Enable Register Name: DMAC_EBCIER Address: 0xFFFFEC18 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 ERR7 ERR6 ERR5 ERR4 ERR3 ERR2 ERR1 ERR0 15 14 13 12 11 10 9 8 CBTC7 CBTC6 CBTC5 CBTC4 CBTC3 CBTC2 CBTC1 CBTC0 7 6 5 4 3 2 1 0 BTC7 BTC6 BTC5 BTC4 BTC3 BTC2 BTC1 BTC0 • BTC[7:0] Buffer Transfer Completed Interrupt Enable Register. Set the relevant bit in the BTC field to enable the interrupt for channeli. • CBTC[7:0] Chained Buffer Transfer Completed Interrupt Enable Register. Set the relevant bit in the CBTC field to enable the interrupt for channel i. • ERR[7:0] Access Error Interrupt Enable Register. Set the relevant bit in the ERR field to enable the interrupt for channel i. 730 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.7 DMAC Error, Buffer Transfer and Chained Buffer Transfer Interrupt Disable Register Name: DMAC_EBCIDR Address: 0xFFFFEC1C Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 ERR7 ERR6 ERR5 ERR4 ERR3 ERR2 ERR1 ERR0 15 14 13 12 11 10 9 8 CBTC7 CBTC6 CBTC5 CBTC4 CBTC3 CBTC2 CBTC1 CBTC0 7 6 5 4 3 2 1 0 BTC7 BTC6 BTC5 BTC4 BTC3 BTC2 BTC1 BTC0 • BTC[7:0] Buffer transfer completed Disable Interrupt Register. When set, a bit of the BTC field disables the interrupt from the rele- vant DMAC channel. • CBTC[7:0] Chained Buffer transfer completed Disable Register. When set, a bit of the CBTC field disables the interrupt from the rele- vant DMAC channel. • ERR[7:0] Access Error Interrupt Disable Register. When set, a bit of the ERR field disables the interrupt from the relevant DMAC channel. SAM9M11 [DATASHEET] 731 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.8 DMAC Error, Buffer Transfer and Chained Buffer Transfer Interrupt Mask Register Name: DMAC_EBCIMR Address: 0xFFFFEC20 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 ERR7 ERR6 ERR5 ERR4 ERR3 ERR2 ERR1 ERR0 15 14 13 12 11 10 9 8 CBTC7 CBTC6 CBTC5 CBTC4 CBTC3 CBTC2 CBTC1 CBTC0 7 6 5 4 3 2 1 0 BTC7 BTC6 BTC5 BTC4 BTC3 BTC2 BTC1 BTC0 • BTC[7:0] 0: Buffer Transfer completed interrupt is disabled for channel i. 1: Buffer Transfer completed interrupt is enabled for channel i. • CBTC[7:0] 0: Chained Buffer Transfer interrupt is disabled for channel i. 1: Chained Buffer Transfer interrupt is enabled for channel i. • ERR[7:0] 0: Transfer Error Interrupt is disabled for channel i. 1: Transfer Error Interrupt is enabled for channel i. 732 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.9 DMAC Error, Buffer Transfer and Chained Buffer Transfer Status Register Name: DMAC_EBCISR Address: 0xFFFFEC24 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 ERR7 ERR6 ERR5 ERR4 ERR3 ERR2 ERR1 ERR0 15 14 13 12 11 10 9 8 CBTC7 CBTC6 CBTC5 CBTC4 CBTC3 CBTC2 CBTC1 CBTC0 7 6 5 4 3 2 1 0 BTC7 BTC6 BTC5 BTC4 BTC3 BTC2 BTC1 BTC0 • BTC[7:0] When BTC[i] is set, Channel i buffer transfer has terminated. • CBTC[7:0] When CBTC[i] is set, Channel i Chained buffer has terminated. LLI Fetch operation is disabled. • ERR[7:0] When ERR[i] is set, Channel i has detected an AHB Read or Write Error Access. SAM9M11 [DATASHEET] 733 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.10DMAC Channel Handler Enable Register Name: DMAC_CHER Address: 0xFFFFEC28 Access: Write-only 31 30 29 28 27 26 25 24 KEEP7 KEEP6 KEEP5 KEEP4 KEEP3 KEEP2 KEEP1 KEEP0 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 SUSP7 SUSP6 SUSP5 SUSP4 SUSP3 SUSP2 SUSP1 SUSP0 7 6 5 4 3 2 1 0 ENA7 ENA6 ENA5 ENA4 ENA3 ENA2 ENA1 ENA0 • ENA[7:0] When set, a bit of the ENA field enables the relevant channel. • SUSP[7:0] When set, a bit of the SUSPfield freezes the relevant channel and its current context. • KEEP[7:0] When set, a bit of the KEEP field resumes the current channel from an automatic stall state. 734 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.11 DMAC Channel Handler Disable Register Name: DMAC_CHDR Address: 0xFFFFEC2C Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 RES7 RES6 RES5 RES4 RES3 RES2 RES1 RES0 7 6 5 4 3 2 1 0 DIS7 DIS6 DIS5 DIS4 DIS3 DIS2 DIS1 DIS0 • DIS[7:0] Write one to this field to disable the relevant DMAC Channel. The content of the FIFO is lost and the current AHB access is terminated. Software must poll DIS[7:0] field in the DMAC_CHSR to be sure that the channel is disabled. • RES[7:0] Write one to this field to resume the channel transfer restoring its context. SAM9M11 [DATASHEET] 735 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.12DMAC Channel Handler Status Register Name: DMAC_CHSR Address: 0xFFFFEC30 Access: Read-only 31 30 29 28 27 26 25 24 STAL7 STAL6 STAL5 STAL4 STAL3 STAL2 STAL1 STAL0 23 22 21 20 19 18 17 16 EMPT7 EMPT6 EMPT5 EMPT4 EMPT3 EMPT2 EMPT1 EMPT0 15 14 13 12 11 10 9 8 SUSP7 SUSP6 SUSP5 SUSP4 SUSP3 SUSP2 SUSP1 SUSP0 7 6 5 4 3 2 1 0 ENA7 ENA6 ENA5 ENA4 ENA3 ENA2 ENA1 ENA0 • ENA[7:0] A one in any position of this field indicates that the relevant channel is enabled. • SUSP[7:0] A one in any position of this field indicates that the channel transfer is suspended. • EMPT[7:0] A one in any position of this field indicates that the relevant channel is empty. • STAL[7:0] A one in any position of this field indicates that the relevant channel is stalling. 736 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.13DMAC Channel x [x = 0..7] Source Address Register Name: DMAC_SADDRx [x = 0..7] Address: 0xFFFFEC3C [0], 0xFFFFEC64 [1], 0xFFFFEC8C [2], 0xFFFFECB4 [3], 0xFFFFECDC [4], 0xFFFFED04 [5], 0xFFFFED2C [6], 0xFFFFED54 [7] Access: Read/Write 31 30 29 28 27 26 25 24 SADDRx 23 22 21 20 19 18 17 16 SADDRx 15 14 13 12 11 10 9 8 SADDRx 7 6 5 4 3 2 1 0 SADDRx • SADDRx Channel x source address. This register must be aligned with the source transfer width. SAM9M11 [DATASHEET] 737 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.14DMAC Channel x [x = 0..7] Destination Address Register Name: DMAC_DADDRx [x = 0..7] Address: 0xFFFFEC40 [0], 0xFFFFEC68 [1], 0xFFFFEC90 [2], 0xFFFFECB8 [3], 0xFFFFECE0 [4], 0xFFFFED08 [5], 0xFFFFED30 [6], 0xFFFFED58 [7] Access: Read/Write 31 30 29 28 27 26 25 24 DADDRx 23 22 21 20 19 18 17 16 DADDRx 15 14 13 12 11 10 9 8 DADDRx 7 6 5 4 3 2 1 0 DADDRx • DADDRx Channel x destination address. This register must be aligned with the destination transfer width. 738 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.15DMAC Channel x [x = 0..7] Descriptor Address Register Name: DMAC_DSCRx [x = 0..7] Address: 0xFFFFEC44 [0], 0xFFFFEC6C [1], 0xFFFFEC94 [2], 0xFFFFECBC [3], 0xFFFFECE4 [4], 0xFFFFED0[5] 0xFFFFED34 [6], 0xFFFFED5C [7] Access: Read/Write 31 30 29 28 27 26 25 24 DSCRx 23 22 21 20 19 18 17 16 DSCRx 15 14 13 12 11 10 9 8 DSCRx 7 6 5 4 3 2 1 0 DSCRx DSCRx_IF • DSCRx_IF 00: The Buffer Transfer descriptor is fetched via AHB-Lite Interface 0. 01: The Buffer Transfer descriptor is fetched via AHB-Lite Interface 1. 10: Reserved. 11: Reserved. • DSCRx Buffer Transfer descriptor address. This address is word aligned. SAM9M11 [DATASHEET] 739 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.16DMAC Channel x [x = 0..7] Control A Register Name: DMAC_CTRLAx [x = 0..7] Address: 0xFFFFEC48 [0], 0xFFFFEC70 [1], 0xFFFFEC98 [2], 0xFFFFECC0 [3], 0xFFFFECE8 [4], 0xFFFFED10 [5], 0xFFFFED38 [6], 0xFFFFED60 [7] Access: Read/Write 31 30 29 28 27 26 25 24 DONE – DST_WIDTH – – SRC_WIDTH 23 22 21 20 19 18 17 16 – DCSIZE – SCSIZE 15 14 13 12 11 10 9 8 BTSIZE 7 6 5 4 3 2 1 0 BTSIZE • BTSIZE Buffer Transfer Size. The transfer size relates to the number of transfers to be performed, that is, for writes it refers to the number of source width transfers to perform when DMAC is flow controller. For Reads, BTSIZE refers to the number of transfers completed on the Source Interface. When this field is set to 0, the DMAC module is automatically disabled when the relevant channel is enabled. • SCSIZE Source Chunk Transfer Size. SCSIZE value Number of data transferred 000 1 001 4 010 8 011 16 100 32 101 64 110 128 111 256 740 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DCSIZE Destination Chunk Transfer size. DCSIZE Number of data transferred 000 1 001 4 010 8 011 16 100 32 101 64 110 128 111 256 • SRC_WIDTH SRC_WIDTH Single Transfer Size 00 BYTE 01 HALF-WORD 1X WORD • DST_WIDTH DST_WIDTH Single Transfer Size 00 BYTE 01 HALF-WORD 1X WORD • DONE 0: The transfer is performed. 1: If SOD field of DMAC_CFG register is set to true, then the DMAC is automatically disabled when an LLI updates the content of this register. The DONE field is written back to memory at the end of the transfer. SAM9M11 [DATASHEET] 741 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.17DMAC Channel x [x = 0..7] Control B Register Name: DMAC_CTRLBx [x = 0..7] Address: 0xFFFFEC4C [0], 0xFFFFEC74 [1], 0xFFFFEC9C [2], 0xFFFFECC4 [3], 0xFFFFECEC [4], 0xFFFFED14 [5], 0xFFFFED3C [6], 0xFFFFED64 [7] Access: Read/Write 31 30 29 28 27 26 25 24 AUTO IEN DST_INCR – – SRC_INCR 23 22 21 20 19 18 17 16 FC DST_DSCR – – – SRC_DSCR 15 14 13 12 11 10 9 8 – – DST_PIP – – – SRC_PIP 7 6 5 4 3 2 1 0 – – DIF – – SIF • SIF: Source Interface Selection Field 00: The source transfer is done via AHB-Lite Interface 0. 01: The source transfer is done via AHB-Lite Interface 1. 10: Reserved. 11: Reserved. • DIF: Destination Interface Selection Field 00: The destination transfer is done via AHB-Lite Interface 0. 01: The destination transfer is done via AHB-Lite Interface 1. 10: Reserved. 11: Reserved. • SRC_PIP 0: Picture-in-Picture mode is disabled. The source data area is contiguous. 1: Picture-in-Picture mode is enabled. When the source PIP counter reaches the programmable boundary, the address is automatically increment of a user defined amount. • DST_PIP 0: Picture-in-Picture mode is disabled. The Destination data area is contiguous. 1: Picture-in-Picture mode is enabled. When the Destination PIP counter reaches the programmable boundary the address is automatically incremented by a user-defined amount. • SRC_DSCR 0: Source address is updated when the descriptor is fetched from the memory. 1: Buffer Descriptor Fetch operation is disabled for the source. 742 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DST_DSCR 0: Destination address is updated when the descriptor is fetched from the memory. 1: Buffer Descriptor Fetch operation is disabled for the destination. • FC This field defines which device controls the size of the buffer transfer, also referred as to the Flow Controller. FC Type of transfer Flow Controller 000 Memory-to-Memory DMA Controller 001 Memory-to-Peripheral DMA Controller 010 Peripheral-to-Memory DMA Controller 011 Peripheral-to-Peripheral DMA Controller 100 Peripheral-to-Memory Peripheral 101 Memory-to-Peripheral Peripheral 110 Peripheral-to-Peripheral Source Peripheral 111 Peripheral-to-Peripheral Destination Peripheral • SRC_INCR SRC_INCR Type of addressing mode 00 INCREMENTING 01 DECREMENTING 10 FIXED • DST_INCR DST_INCR Type of addressing scheme 00 INCREMENTING 01 DECREMENTING 10 FIXED • IEN If this bit is cleared, when the buffer transfer is completed, the BTC[x] flag is set in the EBCISR status register. This bit is active low. • AUTO Automatic multiple buffer transfer is enabled. When set, this bit enables replay mode or contiguous mode when several buffers are transferred. SAM9M11 [DATASHEET] 743 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.18DMAC Channel x [x = 0..7] Configuration Register Name: DMAC_CFGx [x = 0..7] Address: 0xFFFFEC50 [0], 0xFFFFEC78 [1], 0xFFFFECA0 [2], 0xFFFFECC8 [3], 0xFFFFECF0 [4], 0xFFFFED18 [5], 0xFFFFED40 [6], 0xFFFFED68 [7] Access: Read/Write 31 30 29 28 27 26 25 24 – – FIFOCFG – AHB_PROT 23 22 21 20 19 18 17 16 – LOCK_IF_L LOCK_B LOCK_IF – – – SOD 15 14 13 12 11 10 9 8 – – DST_H2SEL DST_REP – – SRC_H2SEL SRC_REP 7 6 5 4 3 2 1 0 DST_PER SRC_PER • SRC_PER Channel x Source Request is associated with peripheral identifier coded SRC_PER handshaking interface. • DST_PER Channel x Destination Request is associated with peripheral identifier coded DST_PER handshaking interface. • SRC_REP 0: When automatic mode is activated, source address is contiguous between two buffers. 1: When automatic mode is activated, the source address and the control register are reloaded from previous transfer. • SRC_H2SEL 0: Software handshaking interface is used to trigger a transfer request. 1: Hardware handshaking interface is used to trigger a transfer request. • DST_REP 0: When automatic mode is activated, destination address is contiguous between two buffers. 1: When automatic mode is activated, the destination and the control register are reloaded from the previous transfer. • DST_H2SEL 0: Software handshaking interface is used to trigger a transfer request. 1: Hardware handshaking interface is used to trigger a transfer request. • SOD 0: STOP ON DONE disabled, the descriptor fetch operation ignores DONE Field of CTRLA register. 1: STOP ON DONE activated, the DMAC module is automatically disabled if DONE FIELD is set to 1. • LOCK_IF 0: Interface Lock capability is disabled 1: Interface Lock capability is enabled 744 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• LOCK_B 0: AHB Bus Locking capability is disabled. 1: AHB Bus Locking capability is enabled. • LOCK_IF_L 0: The Master Interface Arbiter is locked by the channel x for a chunk transfer. 1: The Master Interface Arbiter is locked by the channel x for a buffer transfer. • AHB_PROT AHB_PROT field provides additional information about a bus access and is primarily used to implement some level of protection. HPROT[3] HPROT[2] HPROT[1] HPROT[0] Description 1 Data access 0: User Access AHB_PROT[0] 1: Privileged Access 0: Not Bufferable AHB_PROT[1] 1: Bufferable 0: Not cacheable AHB_PROT[2] 1: Cacheable • FIFOCFG FIFOCFG FIFO Request 00 The largest defined length AHB burst is performed on the destination AHB interface. 01 When half FIFO size is available/filled, a source/destination request is serviced. 10 When there is enough space/data available to perform a single AHB access, then the request is serviced. SAM9M11 [DATASHEET] 745 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.19DMAC Channel x [x = 0..7] Source Picture in Picture Configuration Register Name: DMAC_SPIPx [x = 0..7] Address: 0xFFFFEC54 [0], 0xFFFFEC7C [1], 0xFFFFECA4 [2], 0xFFFFECCC [3], 0xFFFFECF4 [4], 0xFFFFED1C [5], 0xFFFFED44 [6], 0xFFFFED6C [7] Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – SPIP_BOUNDARY 23 22 21 20 19 18 17 16 SPIP_BOUNDARY 15 14 13 12 11 10 9 8 SPIP_HOLE 7 6 5 4 3 2 1 0 SPIP_HOLE • SPIP_HOLE This field indicates the value to add to the address when the programmable boundary has been reached. • SPIP_BOUNDARY This field indicates the number of source transfers to perform before the automatic address increment operation. 746 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

34.7.20DMAC Channel x [x = 0..7] Destination Picture in Picture Configuration Register Name: DMAC_DPIPx [x = 0..7] Address: 0xFFFFEC58 [0], 0xFFFFEC80 [1], 0xFFFFECA8 [2], 0xFFFFECD0 [3], 0xFFFFECF8 [4], 0xFFFFED20 [5], 0xFFFFED48 [6], 0xFFFFED70 [7] Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – DPIP_BOUNDARY 23 22 21 20 19 18 17 16 DPIP_BOUNDARY 15 14 13 12 11 10 9 8 DPIP_HOLE 7 6 5 4 3 2 1 0 DPIP_HOLE • DPIP_HOLE This field indicates the value to add to the address when the programmable boundary has been reached. • DPIP_BOUNDARY This field indicates the number of source transfers to perform before the automatic address increment operation. SAM9M11 [DATASHEET] 747 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35. Pulse Width Modulation Controller (PWM) 35.1 Description The PWM macrocell controls several channels independently. Each channel controls one square output waveform. Characteristics of the output waveform such as period, duty-cycle and polarity are configurable through the user interface. Each channel selects and uses one of the clocks provided by the clock generator. The clock generator provides several clocks resulting from the division of the PWM macrocell master clock. All PWM macrocell accesses are made through APB mapped registers. Channels can be synchronized, to generate non overlapped waveforms. All channels integrate a double buffering system in order to prevent an unexpected output waveform while modifying the period or the duty-cycle. 35.2 Embedded Characteristics  Four channels, one 16-bit counter per channel  Common clock generator, providing Thirteen Different Clocks ̶ A Modulo n counter providing eleven clocks ̶ Two independent Linear Dividers working on modulo n counter outputs  Independent channel programming ̶ Independent Enable Disable Commands ̶ Independent Clock Selection ̶ Independent Period and Duty Cycle, with Double Buffering ̶ Programmable selection of the output waveform polarity ̶ Programmable center or left aligned output waveform 748 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.3 Block Diagram Figure 35-1. Pulse Width Modulation Controller Block Diagram PWM Controller PWMx Channel Period Update PWMx Comparator Duty Cycle PWMx Clock Selector Counter PIO PWM0 Period Channel Update PWM0 Comparator Duty Cycle PWM0 Clock Selector Counter MCK PMC Clock Generator APB Interface Interrupt Generator AIC APB 35.4 I/O Lines Description Each channel outputs one waveform on one external I/O line. Table 35-1. I/O Line Description Name Description Type PWMx PWM Waveform Output for channel x Output SAM9M11 [DATASHEET] 749 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.5 Product Dependencies 35.5.1 I/O Lines The pins used for interfacing the PWM may be multiplexed with PIO lines. The programmer must first program the PIO controller to assign the desired PWM pins to their peripheral function. If I/O lines of the PWM are not used by the application, they can be used for other purposes by the PIO controller. All of the PWM outputs may or may not be enabled. If an application requires only four channels, then only four PIO lines will be assigned to PWM outputs. Table 35-2. I/O Lines Instance Signal I/O Line Peripheral PWM PWM0 PD24 B PWM PWM1 PD25 B PWM PWM1 PD31 B PWM PWM2 PD26 B PWM PWM2 PE31 A PWM PWM3 PA25 B PWM PWM3 PD0 B 35.5.2 Power Management The PWM is not continuously clocked. The programmer must first enable the PWM clock in the Power Management Controller (PMC) before using the PWM. However, if the application does not require PWM operations, the PWM clock can be stopped when not needed and be restarted later. In this case, the PWM will resume its operations where it left off. Configuring the PWM does not require the PWM clock to be enabled. 35.5.3 Interrupt Sources The PWM interrupt line is connected on one of the internal sources of the Advanced Interrupt Controller. Using the PWM interrupt requires the AIC to be programmed first. Note that it is not recommended to use the PWM interrupt line in edge sensitive mode. Table 35-3. Peripheral IDs Instance ID PWM 19 750 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.6 Functional Description The PWM macrocell is primarily composed of a clock generator module and 4 channels. ̶ Clocked by the system clock, MCK, the clock generator module provides 13 clocks. ̶ Each channel can independently choose one of the clock generator outputs. ̶ Each channel generates an output waveform with attributes that can be defined independently for each channel through the user interface registers. 35.6.1 PWM Clock Generator Figure 35-2. Functional View of the Clock Generator Block Diagram modulo n counter MCK MCK MCK/2 MCK/4 MCK/8 MCK/16 MCK/32 MCK/64 MCK/128 MCK/256 MCK/512 MCK/1024 Divider A clkA PREA DIVA PWM_MR Divider B clkB PREB DIVB PWM_MR CAUTION: Before using the PWM macrocell, the programmer must first enable the PWM clock in the Power Management Controller (PMC). The PWM macrocell master clock, MCK, is divided in the clock generator module to provide different clocks available for all channels. Each channel can independently select one of the divided clocks. The clock generator is divided in three blocks: ̶ a modulo n counter which provides 11 clocks: f , f /2, f /4, f /8, f /16, f /32, f /64, MCK MCK MCK MCK MCK MCK MCK f /128, f /256, f /512, f /1024 MCK MCK MCK MCK ̶ two linear dividers (1, 1/2, 1/3, ... 1/255) that provide two separate clocks: clkA and clkB Each linear divider can independently divide one of the clocks of the modulo n counter. The selection of the clock to be divided is made according to the PREA (PREB) field of the PWM Mode Register (PWM_MR). The resulting clock clkA (clkB) is the clock selected divided by DIVA (DIVB) field value in the PWM Mode Register (PWM_MR). SAM9M11 [DATASHEET] 751 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

After a reset of the PWM controller, DIVA (DIVB) and PREA (PREB) in the PWM Mode register are set to 0. This implies that after reset clkA (clkB) are turned off. At reset, all clocks provided by the modulo n counter are turned off except clock “clk”. This situation is also true when the PWM master clock is turned off through the Power Management Controller. 35.6.2 PWM Channel 35.6.2.1 Block Diagram Figure 35-3. Functional View of the Channel Block Diagram inputs from clock Channel generator Clock Internal Comparator PWMx Selector Counter output waveform inputs from APB bus Each of the 4 channels is composed of three blocks:  A clock selector which selects one of the clocks provided by the clock generator described in Section 35.6.1 “PWM Clock Generator” on page 751.  An internal counter clocked by the output of the clock selector. This internal counter is incremented or decremented according to the channel configuration and comparators events. The size of the internal counter is 16 bits.  A comparator used to generate events according to the internal counter value. It also computes the PWMx output waveform according to the configuration. 752 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.6.2.2 Waveform Properties The different properties of output waveforms are:  the internal clock selection. The internal channel counter is clocked by one of the clocks provided by the clock generator described in the previous section. This channel parameter is defined in the CPRE field of the PWM_CMRx register. This field is reset at 0.  the waveform period. This channel parameter is defined in the CPRD field of the PWM_CPRDx register. - If the waveform is left aligned, then the output waveform period depends on the counter source clock and can be calculated: By using the Master Clock (MCK) divided by an X given prescaler value (with X being 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, or 1024), the resulting period formula willbe: (X×CPRD) ------------------------------- MCK By using a Master Clock divided by one of both DIVA or DIVB divider, the formula becomes, respectively: (X*CPRD*DIVA) (X*CPRD*DIVB) ----------------------------------------------- or ----------------------------------------------- MCK MCK If the waveform is center aligned then the output waveform period depends on the counter source clock and can be calculated: By using the Master Clock (MCK) divided by an X given prescaler value (with X being 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, or 1024). The resulting period formula will be: (2×X×CPRD) ---------------------------------------- MCK By using a Master Clock divided by one of both DIVA or DIVB divider, the formula becomes, respectively: (2*X*CPRD*DIVA) (2*X*CPRD*DIVB) ------------------------------------------------------ or ------------------------------------------------------ MCK MCK  the waveform duty cycle. This channel parameter is defined in the CDTY field of the PWM_CDTYx register. If the waveform is left aligned then: (period–1⁄fchannel_x_clock×CDTY) duty cycle = ---------------------------------------------------------------------------------------------------- period If the waveform is center aligned, then: ((period⁄2)–1⁄fchannel_x_clock×CDTY)) duty cycle = ------------------------------------------------------------------------------------------------------------------- (period⁄2)  the waveform polarity. At the beginning of the period, the signal can be at high or low level. This property is defined in the CPOL field of the PWM_CMRx register. By default the signal starts by a low level.  the waveform alignment. The output waveform can be left or center aligned. Center aligned waveforms can be used to generate non overlapped waveforms. This property is defined in the CALG field of the PWM_CMRx register. The default mode is left aligned. SAM9M11 [DATASHEET] 753 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 35-4. Non Overlapped Center Aligned Waveforms No overlap PWM0 PWM1 Period Note: 1. See Figure 35-5 on page 755 for a detailed description of center aligned waveforms. When center aligned, the internal channel counter increases up to CPRD and.decreases down to 0. This ends the period. When left aligned, the internal channel counter increases up to CPRD and is reset. This ends the period. Thus, for the same CPRD value, the period for a center aligned channel is twice the period for a left aligned channel. Waveforms are fixed at 0 when:  CDTY = CPRD and CPOL = 0  CDTY = 0 and CPOL = 1 Waveforms are fixed at 1 (once the channel is enabled) when:  CDTY = 0 and CPOL = 0  CDTY = CPRD and CPOL = 1 The waveform polarity must be set before enabling the channel. This immediately affects the channel output level. Changes on channel polarity are not taken into account while the channel is enabled. 754 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 35-5. Waveform Properties PWM_MCKx CHIDx(PWM_SR) CHIDx(PWM_ENA) CHIDx(PWM_DIS) Center Aligned CALG(PWM_CMRx) = 1 PWM_CCNTx CPRD(PWM_CPRDx) CDTY(PWM_CDTYx) Period Output Waveform PWMx CPOL(PWM_CMRx) = 0 Output Waveform PWMx CPOL(PWM_CMRx) = 1 CHIDx(PWM_ISR) Left Aligned CALG(PWM_CMRx) = 0 PWM_CCNTx CPRD(PWM_CPRDx) CDTY(PWM_CDTYx) Period Output Waveform PWMx CPOL(PWM_CMRx) = 0 Output Waveform PWMx CPOL(PWM_CMRx) = 1 CHIDx(PWM_ISR) SAM9M11 [DATASHEET] 755 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.6.3 PWM Controller Operations 35.6.3.1 Initialization Before enabling the output channel, this channel must have been configured by the software application:  Configuration of the clock generator if DIVA and DIVB are required  Selection of the clock for each channel (CPRE field in the PWM_CMRx register)  Configuration of the waveform alignment for each channel (CALG field in the PWM_CMRx register)  Configuration of the period for each channel (CPRD in the PWM_CPRDx register). Writing in PWM_CPRDx Register is possible while the channel is disabled. After validation of the channel, the user must use PWM_CUPDx Register to update PWM_CPRDx as explained below.  Configuration of the duty cycle for each channel (CDTY in the PWM_CDTYx register). Writing in PWM_CDTYx Register is possible while the channel is disabled. After validation of the channel, the user must use PWM_CUPDx Register to update PWM_CDTYx as explained below.  Configuration of the output waveform polarity for each channel (CPOL in the PWM_CMRx register)  Enable Interrupts (Writing CHIDx in the PWM_IER)  Enable the PWM channel (Writing CHIDx in the PWM_ENA register) It is possible to synchronize different channels by enabling them at the same time by means of writing simultaneously several CHIDx bits in the PWM_ENA register.  In such a situation, all channels may have the same clock selector configuration and the same period specified. 35.6.3.2 Source Clock Selection Criteria The large number of source clocks can make selection difficult. The relationship between the value in the Period Register (PWM_CPRDx) and the Duty Cycle Register (PWM_CDTYx) can help the user in choosing. The event number written in the Period Register gives the PWM accuracy. The Duty Cycle quantum cannot be lower than 1/PWM_CPRDx value. The higher the value of PWM_CPRDx, the greater the PWM accuracy. For example, if the user sets 15 (in decimal) in PWM_CPRDx, the user is able to set a value between 1 up to 14 in PWM_CDTYx Register. The resulting duty cycle quantum cannot be lower than 1/15 of the PWM period. 35.6.3.3 Changing the Duty Cycle or the Period It is possible to modulate the output waveform duty cycle or period. To prevent unexpected output waveform, the user must use the update register (PWM_CUPDx) to change waveform parameters while the channel is still enabled. The user can write a new period value or duty cycle value in the update register (PWM_CUPDx). This register holds the new value until the end of the current cycle and updates the value for the next cycle. Depending on the CPD field in the PWM_CMRx register, PWM_CUPDx either updates PWM_CPRDx or PWM_CDTYx. Note that even if the update register is used, the period must not be smaller than the duty cycle. 756 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 35-6. Synchronized Period or Duty Cycle Update User'sWriting PWM_CUPDx Value 1 0 PWM_CMRx. CPD PWM_CPRDx PWM_CDTYx End ofCycle To prevent overwriting the PWM_CUPDx by software, the user can use status events in order to synchronize his software. Two methods are possible. In both, the user must enable the dedicated interrupt in PWM_IER at PWM Controller level. The first method (polling method) consists of reading the relevant status bit in PWM_ISR Register according to the enabled channel(s). See Figure 35-7. The second method uses an Interrupt Service Routine associated with the PWM channel. Note: Reading the PWM_ISR automatically clears CHIDx flags. Figure 35-7. Polling Method PWM_ISR Read Acknowledgement and clear previous register state Writing in CPD field Update of the Period or Duty Cycle CHIDx = 1 YES Writing in PWM_CUPDx The last write has been taken into account Note: Polarity and alignment can be modified only when the channel is disabled. 35.6.3.4 Interrupts Depending on the interrupt mask in the PWM_IMR, an interrupt is generated at the end of the corresponding channel period. The interrupt remains active until a read operation in the PWM_ISR occurs. A channel interrupt is enabled by setting the corresponding bit in the PWM_IER. A channel interrupt is disabled by setting the corresponding bit in the PWM_IDR. SAM9M11 [DATASHEET] 757 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.7 Pulse Width Modulation Controller (PWM) User Interface Table 35-4. Register Mapping(1) Offset Register Name Access Reset 0x00 PWM Mode Register PWM_MR Read/Write 0 0x04 PWM Enable Register PWM_ENA Write-only – 0x08 PWM Disable Register PWM_DIS Write-only – 0x0C PWM Status Register PWM_SR Read-only 0 0x10 PWM Interrupt Enable Register PWM_IER Write-only – 0x14 PWM Interrupt Disable Register PWM_IDR Write-only – 0x18 PWM Interrupt Mask Register PWM_IMR Read-only 0 0x1C PWM Interrupt Status Register PWM_ISR Read-only 0 0x20–0xFC Reserved – – – 0x100–0x1FC Reserved – – – 0x200 + ch_num * 0x20 + 0x00 PWM Channel Mode Register PWM_CMR Read/Write 0x0 0x200 + ch_num * 0x20 + 0x04 PWM Channel Duty Cycle Register PWM_CDTY Read/Write 0x0 0x200 + ch_num * 0x20 + 0x08 PWM Channel Period Register PWM_CPRD Read/Write 0x0 0x200 + ch_num * 0x20 + 0x0C PWM Channel Counter Register PWM_CCNT Read-only 0x0 0x200 + ch_num * 0x20 + 0x10 PWM Channel Update Register PWM_CUPD Write-only – Note: 1. Some registers are indexed with “ch_num” index ranging from 0 to 3. 758 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.7.1 PWM Mode Register Name: PWM_MR Address: 0xFFFB8000 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – PREB 23 22 21 20 19 18 17 16 DIVB 15 14 13 12 11 10 9 8 – – – – PREA 7 6 5 4 3 2 1 0 DIVA • DIVA, DIVB: CLKA, CLKB Divide Factor DIVA, DIVB CLKA, CLKB 0 CLKA, CLKB clock is turned off 1 CLKA, CLKB clock is clock selected by PREA, PREB 2–255 CLKA, CLKB clock is clock selected by PREA, PREB divided by DIVA, DIVB factor. • PREA, PREB PREA, PREB Divider Input Clock 0 0 0 0 MCK 0 0 0 1 MCK/2 0 0 1 0 MCK/4 0 0 1 1 MCK/8 0 1 0 0 MCK/16 0 1 0 1 MCK/32 0 1 1 0 MCK/64 0 1 1 1 MCK/128 1 0 0 0 MCK/256 1 0 0 1 MCK/512 1 0 1 0 MCK/1024 Other Reserved SAM9M11 [DATASHEET] 759 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.7.2 PWM Enable Register Name: PWM_ENA Address: 0xFFFB8004 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – CHID3 CHID2 CHID1 CHID0 • CHIDx: Channel ID 0: No effect. 1: Enable PWM output for channel x. 760 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.7.3 PWM Disable Register Name: PWM_DIS Address: 0xFFFB8008 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – CHID3 CHID2 CHID1 CHID0 • CHIDx: Channel ID 0: No effect. 1: Disable PWM output for channel x. SAM9M11 [DATASHEET] 761 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.7.4 PWM Status Register Name: PWM_SR Address: 0xFFFB800C Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – CHID3 CHID2 CHID1 CHID0 • CHIDx: Channel ID 0: PWM output for channel x is disabled. 1: PWM output for channel x is enabled. 762 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.7.5 PWM Interrupt Enable Register Name: PWM_IER Address: 0xFFFB8010 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – CHID3 CHID2 CHID1 CHID0 • CHIDx: Channel ID 0: No effect. 1: Enable interrupt for PWM channel x. SAM9M11 [DATASHEET] 763 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.7.6 PWM Interrupt Disable Register Name: PWM_IDR Address: 0xFFFB8014 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – CHID3 CHID2 CHID1 CHID0 • CHIDx: Channel ID 0: No effect. 1: Disable interrupt for PWM channel x. 764 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.7.7 PWM Interrupt Mask Register Name: PWM_IMR Address: 0xFFFB8018 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – CHID3 CHID2 CHID1 CHID0 • CHIDx: Channel ID 0: Interrupt for PWM channel x is disabled. 1: Interrupt for PWM channel x is enabled. SAM9M11 [DATASHEET] 765 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.7.8 PWM Interrupt Status Register Name: PWM_ISR Address: 0xFFFB801C Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – CHID3 CHID2 CHID1 CHID0 • CHIDx: Channel ID 0: No new channel period has been achieved since the last read of the PWM_ISR. 1: At least one new channel period has been achieved since the last read of the PWM_ISR. Note: Reading PWM_ISR automatically clears CHIDx flags. 766 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.7.9 PWM Channel Mode Register Name: PWM_CMR[0..3] Address: 0xFFFB8200 [0], 0xFFFB8220 [1], 0xFFFB8240 [2], 0xFFFB8260 [3] Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – CPD CPOL CALG 7 6 5 4 3 2 1 0 – – – – CPRE • CPRE: Channel Pre-scaler CPRE Channel Pre-scaler 0 0 0 0 MCK 0 0 0 1 MCK/2 0 0 1 0 MCK/4 0 0 1 1 MCK/8 0 1 0 0 MCK/16 0 1 0 1 MCK/32 0 1 1 0 MCK/64 0 1 1 1 MCK/128 1 0 0 0 MCK/256 1 0 0 1 MCK/512 1 0 1 0 MCK/1024 1 0 1 1 CLKA 1 1 0 0 CLKB Other Reserved • CALG: Channel Alignment 0: The period is left aligned. 1: The period is center aligned. • CPOL: Channel Polarity 0: The output waveform starts at a low level. 1: The output waveform starts at a high level. SAM9M11 [DATASHEET] 767 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• CPD: Channel Update Period 0: Writing to the PWM_CUPDx will modify the duty cycle at the next period start event. 1: Writing to the PWM_CUPDx will modify the period at the next period start event. 768 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.7.10PWM Channel Duty Cycle Register Name: PWM_CDTY[0..3] Address: 0xFFFB8204 [0], 0xFFFB8224 [1], 0xFFFB8244 [2], 0xFFFB8264 [3] Access: Read/Write 31 30 29 28 27 26 25 24 CDTY 23 22 21 20 19 18 17 16 CDTY 15 14 13 12 11 10 9 8 CDTY 7 6 5 4 3 2 1 0 CDTY Only the first 16 bits (internal channel counter size) are significant. • CDTY: Channel Duty Cycle Defines the waveform duty cycle. This value must be defined between 0 and CPRD (PWM_CPRx). SAM9M11 [DATASHEET] 769 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.7.11 PWM Channel Period Register Name: PWM_CPRD[0..3] Address: 0xFFFB8208 [0], 0xFFFB8228 [1], 0xFFFB8248 [2], 0xFFFB8268 [3] Access: Read/Write 31 30 29 28 27 26 25 24 CPRD 23 22 21 20 19 18 17 16 CPRD 15 14 13 12 11 10 9 8 CPRD 7 6 5 4 3 2 1 0 CPRD Only the first 16 bits (internal channel counter size) are significant. • CPRD: Channel Period If the waveform is left-aligned, then the output waveform period depends on the counter source clock and can be calculated: – By using the Master Clock (MCK) divided by an X given prescaler value (with X being 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, or 1024). The resulting period formula will be: (X×CPRD) ------------------------------- MCK – By using a Master Clock divided by one of both DIVA or DIVB divider, the formula becomes, respectively: (CRPD×DIVA) (CRPD×DIVAB) ------------------------------------------ or ---------------------------------------------- MCK MCK If the waveform is center-aligned, then the output waveform period depends on the counter source clock and can be calculated: – By using the Master Clock (MCK) divided by an X given prescaler value (with X being 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, or 1024). The resulting period formula will be: (2×X×CPRD) ---------------------------------------- MCK – By using a Master Clock divided by one of both DIVA or DIVB divider, the formula becomes, respectively: (2×CPRD×DIVA) (2×CPRD×DIVB) --------------------------------------------------- or --------------------------------------------------- MCK MCK 770 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.7.12PWM Channel Counter Register Name: PWM_CCNT[0..3] Address: 0xFFFB820C [0], 0xFFFB822C [1], 0xFFFB824C [2], 0xFFFB826C [3] Access: Read-only 31 30 29 28 27 26 25 24 CNT 23 22 21 20 19 18 17 16 CNT 15 14 13 12 11 10 9 8 CNT 7 6 5 4 3 2 1 0 CNT • CNT: Channel Counter Register Internal counter value. This register is reset when: – the channel is enabled (writing CHIDx in the PWM_ENA register). – the counter reaches CPRD value defined in the PWM_CPRDx register if the waveform is left aligned. SAM9M11 [DATASHEET] 771 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

35.7.13PWM Channel Update Register Name: PWM_CUPD[0..3] Address: 0xFFFB8210 [0], 0xFFFB8230 [1], 0xFFFB8250 [2], 0xFFFB8270 [3] Access: Write-only 31 30 29 28 27 26 25 24 CUPD 23 22 21 20 19 18 17 16 CUPD 15 14 13 12 11 10 9 8 CUPD 7 6 5 4 3 2 1 0 CUPD • CUPD: Channel Update Register This register acts as a double buffer for the period or the duty cycle. This prevents an unexpected waveform when modify- ing the waveform period or duty-cycle. Only the first 16 bits (internal channel counter size) are significant. CPD (PWM_CMRx Register) Description The duty-cycle (CDTY in the PWM_CDTYx register) is updated with the CUPD value at the 0 beginning of the next period. The period (CPRD in the PWM_CPRDx register) is updated with the CUPD value at the beginning 1 of the next period. 772 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36. High Speed Multimedia Card Interface (HSMCI) 36.1 Description The High Speed Multimedia Card Interface (HSMCI) supports the MultiMedia Card (MMC) Specification V4.3, the SD Memory Card Specification V2.0, the SDIO V2.0 specification and CE-ATA V1.1. The HSMCI includes a command register, response registers, data registers, timeout counters and error detection logic that automatically handle the transmission of commands and, when required, the reception of the associated responses and data with a limited processor overhead. The HSMCI supports stream, block and multi block data read and write, and is compatible with the DMA Controller (DMAC), minimizing processor intervention for large buffer transfers. The HSMCI operates at a rate of up to Master Clock divided by 2 and supports the interfacing of 1 slot(s). Each slot may be used to interface with a High Speed MultiMediaCard bus (up to 30 Cards) or with an SD Memory Card. Only one slot can be selected at a time (slots are multiplexed). A bit field in the SD Card Register performs this selection. The SD Memory Card communication is based on a 9-pin interface (clock, command, four data and three power lines) and the High Speed MultiMedia Card on a 7-pin interface (clock, command, one data, three power lines and one reserved for future use). The SD Memory Card interface also supports High Speed MultiMedia Card operations. The main differences between SD and High Speed MultiMedia Cards are the initialization process and the bus topology. HSMCI fully supports CE-ATA Revision 1.1, built on the MMC System Specification v4.0. The module includes dedicated hardware to issue the command completion signal and capture the host command completion signal disable. 36.2 Embedded Characteristics  Compatible with MultiMedia Card Specification Version 4.3  Compatible with SD Memory Card Specification Version 2.0  Compatible with SDIO Specification Version 2.0  Compatible with CE-ATA Specification 1.1  Cards Clock Rate Up to Master Clock Divided by 2  Boot Operation Mode Support  High Speed Mode Support  Embedded Power Management to Slow Down Clock Rate When Not Used  Supports 1 Multiplexed Slot(s) ̶ Each Slot for either a High Speed MultiMediaCard Bus (Up to 30 Cards) or an SD Memory Card  Support for Stream, Block and Multi-block Data Read and Write  Supports Connection to DMA Controller (DMAC) ̶ Minimizes Processor Intervention for Large Buffer Transfers  Built in FIFO (from 16 to 256 bytes) with Large Memory Aperture Supporting Incremental Access  Support for CE-ATA Completion Signal Disable Command  Protection Against Unexpected Modification On-the-Fly of the Configuration Registers SAM9M11 [DATASHEET] 773 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.3 Block Diagram Figure 36-1. Block Diagram APB Bridge DMAC APB MCCK (1) MCCDA (1) HSMCI Interface MCDA0 (1) MCK PMC PIO MCDA1 (1) MCDA2 (1) MCDA3 (1) MCDA4 (1) MCDA5 (1) MCDA6 (1) Interrupt Control MCDA7 (1) HSMCI Interrupt Notes: 1. When several HSMCI (x HSMCI) are embedded in a product, MCCK refers to HSMCIx_CK, MCCDA to HSMCIx_CDA, MCDAy to HSMCIx_DAy. 774 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.4 Application Block Diagram Figure 36-2. Application Block Diagram Application Layer ex: File System, Audio, Security, etc. Physical Layer HSMCI Interface 1 2 3 4 5 6 7 123456 78 9 91011 12138 MMC SDCard 36.5 Pin Name List Table 36-1. I/O Lines Description for 8-bit Configuration Pin Name(2) Pin Description Type(1) Comments MCCDA Command/response I/O/PP/OD CMD of an MMC or SDCard/SDIO MCCK Clock I/O CLK of an MMC or SD Card/SDIO DAT[0..7] of an MMC MCDA0–MCDA7 Data 0..7 of Slot A I/O/PP DAT[0..3] of an SD Card/SDIO Notes: 1. I: Input, O: Output, PP: Push/Pull, OD: Open Drain. 2. When several HSMCI (x HSMCI) are embedded in a product, MCCK refers to HSMCIx_CK, MCCDA to HSMCIx_CDA, MCDAy to HSMCIx_DAy. SAM9M11 [DATASHEET] 775 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.6 Product Dependencies 36.6.1 I/O Lines The pins used for interfacing the High Speed MultiMedia Cards or SD Cards are multiplexed with PIO lines. The programmer must first program the PIO controllers to assign the peripheral functions to HSMCI pins. Table 36-2. I/O Lines Instance Signal I/O Line Peripheral HSMCI0 MCI0_CDA PA1 A HSMCI0 MCI0_CK PA0 A HSMCI0 MCI0_DA0 PA2 A HSMCI0 MCI0_DA1 PA3 A HSMCI0 MCI0_DA2 PA4 A HSMCI0 MCI0_DA3 PA5 A HSMCI0 MCI0_DA4 PA6 A HSMCI0 MCI0_DA5 PA7 A HSMCI0 MCI0_DA6 PA8 A HSMCI0 MCI0_DA7 PA9 A HSMCI1 MCI1_CDA PA22 A HSMCI1 MCI1_CK PA31 A HSMCI1 MCI1_DA0 PA23 A HSMCI1 MCI1_DA1 PA24 A HSMCI1 MCI1_DA2 PA25 A HSMCI1 MCI1_DA3 PA26 A HSMCI1 MCI1_DA4 PA27 A HSMCI1 MCI1_DA5 PA28 A HSMCI1 MCI1_DA6 PA29 A HSMCI1 MCI1_DA7 PA30 A 36.6.2 Power Management The HSMCI is clocked through the Power Management Controller (PMC), so the programmer must first configure the PMC to enable the HSMCI clock. 36.6.3 Interrupt The HSMCI interface has an interrupt line connected to the Advanced Interrupt Controller (AIC). Handling the HSMCI interrupt requires programming the AIC before configuring the HSMCI. Table 36-3. Peripheral IDs Instance ID HSMCI0 11 HSMCI1 29 776 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.7 Bus Topology Figure 36-3. High Speed MultiMedia Memory Card Bus Topology 1 2 3 4 5 6 7 91011 12138 MMC The High Speed MultiMedia Card communication is based on a 13-pin serial bus interface. It has three communication lines and four supply lines. Table 36-4. Bus Topology HSMCI Pin Name(2) Pin Number Name Type(1) Description (Slot z) 1 DAT[3] I/O/PP Data MCDz3 2 CMD I/O/PP/OD Command/response MCCDz 3 VSS1 S Supply voltage ground VSS 4 VDD S Supply voltage VDD 5 CLK I/O Clock MCCK 6 VSS2 S Supply voltage ground VSS 7 DAT[0] I/O/PP Data 0 MCDz0 8 DAT[1] I/O/PP Data 1 MCDz1 9 DAT[2] I/O/PP Data 2 MCDz2 10 DAT[4] I/O/PP Data 4 MCDz4 11 DAT[5] I/O/PP Data 5 MCDz5 12 DAT[6] I/O/PP Data 6 MCDz6 13 DAT[7] I/O/PP Data 7 MCDz7 Notes: 1. I: Input, O: Output, PP: Push/Pull, OD: Open Drain. 2. When several HSMCI (x HSMCI) are embedded in a product, MCCK refers to HSMCIx_CK, MCCDA to HSMCIx_CDA, MCDAy to HSMCIx_DAy. SAM9M11 [DATASHEET] 777 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 36-4. MMC Bus Connections (One Slot) HSMCI MCDA0 MCCDA MCCK 1 2 3 4 5 6 7 1 2 3 4 5 6 7 1 2 3 4 5 6 7 91011 12138 91011 12138 91011 12138 MMC1 MMC2 MMC3 Note: When several HSMCI (x HSMCI) are embedded in a product, MCCK refers to HSMCIx_CK, MCCDA to HSMCIx_CDA MCDAy to HSMCIx_DAy. Figure 36-5. SD Memory Card Bus Topology 123456 78 9 SD CARD The SD Memory Card bus includes the signals listed in Table 36-5. Table 36-5. SD Memory Card Bus Signals HSMCI Pin Name(2) Pin Number Name Type(1) Description (Slot z) 1 CD/DAT[3] I/O/PP Card detect/ Data line Bit 3 MCDz3 2 CMD PP Command/response MCCDz 3 VSS1 S Supply voltage ground VSS 4 VDD S Supply voltage VDD 5 CLK I/O Clock MCCK 6 VSS2 S Supply voltage ground VSS 7 DAT[0] I/O/PP Data line Bit 0 MCDz0 8 DAT[1] I/O/PP Data line Bit 1 or Interrupt MCDz1 9 DAT[2] I/O/PP Data line Bit 2 MCDz2 Notes: 1. I: input, O: output, PP: Push Pull, OD: Open Drain. 2. When several HSMCI (x HSMCI) are embedded in a product, MCCK refers to HSMCIx_CK, MCCDA to HSMCIx_CDA, MCDAy to HSMCIx_DAy. 778 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 36-6. SD Card Bus Connections with One Slot 8 MCDA0 - MCDA3 7 6 MCCK 5 SD CARD 4 3 MCCDA 2 1 9 Note: When several HSMCI (x HSMCI) are embedded in a product, MCCK refers to HSMCIx_CK, MCCDA to HSMCIx_CDA MCDAy to HSMCIx_DAy. When the HSMCI is configured to operate with SD memory cards, the width of the data bus can be selected in the HSMCI SDCard/SDIO Register (HSMCI_SDCR). Clearing the SDCBUS bit in this register means that the width is one bit; setting it means that the width is four bits. In the case of High Speed MultiMedia cards, only the data line 0 is used. The other data lines can be used as independent PIOs. 36.8 High Speed MultiMediaCard Operations After a power-on reset, the cards are initialized by a special message-based High Speed MultiMediaCard bus protocol. Each message is represented by one of the following tokens:  Command: A command is a token that starts an operation. A command is sent from the host either to a single card (addressed command) or to all connected cards (broadcast command). A command is transferred serially on the CMD line.  Response: A response is a token which is sent from an addressed card or (synchronously) from all connected cards to the host as an answer to a previously received command. A response is transferred serially on the CMD line.  Data: Data can be transferred from the card to the host or vice versa. Data is transferred via the data line. Card addressing is implemented using a session address assigned during the initialization phase by the bus controller to all currently connected cards. Their unique CID number identifies individual cards. The structure of commands, responses and data blocks is described in the High Speed MultiMedia-Card System Specification. See also Table 36-6 on page 780. High Speed MultiMediaCard bus data transfers are composed of these tokens. There are different types of operations. Addressed operations always contain a command and a response token. In addition, some operations have a data token; the others transfer their information directly within the command or response structure. In this case, no data token is present in an operation. The bits on the DAT and the CMD lines are transferred synchronous to the clock HSMCI Clock. Two types of data transfer commands are defined:  Sequential commands: These commands initiate a continuous data stream. They are terminated only when a stop command follows on the CMD line. This mode reduces the command overhead to an absolute minimum.  Block-oriented commands: These commands send a data block succeeded by CRC bits. Both read and write operations allow either single or multiple block transmission. A multiple block transmission is terminated when a stop command follows on the CMD line similarly to the sequential read or when a multiple block transmission has a pre-defined block count (See “Data Transfer Operation” on page 783.). The HSMCI provides a set of registers to perform the entire range of High Speed MultiMedia Card operations. SAM9M11 [DATASHEET] 779 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.8.1 Command - Response Operation After reset, the HSMCI is disabled and becomes valid after setting the MCIEN bit in the HSMCI Control Register (HSMCI_CR). The PWSEN bit saves power by dividing the HSMCI clock by 2PWSDIV + 1 when the bus is inactive. The two bits, RDPROOF and WRPROOF in the HSMCI Mode Register (HSMCI_MR) allow stopping the HSMCI Clock during read or write access if the internal FIFO is full. This will guarantee data integrity, not bandwidth. All the timings for High Speed MultiMedia Card are defined in the High Speed MultiMediaCard System Specification. The two bus modes (open drain and push/pull) needed to process all the operations are defined in the HSMCI Command Register (HSMCI_CMDR). The HSMCI_CMDR allows a command to be carried out. For example, to perform an ALL_SEND_CID command: Host Command N Cycles Response High Impedance State ID CMD S T Content CRC E Z ****** Z S T CID Content Z Z Z The command ALL_SEND_CID and the fields and values for the HSMCI_CMDR are described in Table 36-6 and Table 36-7. Table 36-6. ALL_SEND_CID Command Description CMD Index Type Argument Resp Abbreviation Command Description CMD2 bcr(1) [31:0] stuff bits R2 ALL_SEND_CID Asks all cards to send their CID numbers on the CMD line Note: 1. bcr means broadcast command with response. Table 36-7. Fields and Values for HSMCI_CMDR Field Value CMDNB (command number) 2 (CMD2) RSPTYP (response type) 2 (R2: 136 bits response) SPCMD (special command) 0 (not a special command) OPCMD (open drain command) 1 MAXLAT (max latency for command to response) 0 (NID cycles ==> 5 cycles) TRCMD (transfer command) 0 (No transfer) TRDIR (transfer direction) X (available only in transfer command) TRTYP (transfer type) X (available only in transfer command) IOSPCMD (SDIO special command) 0 (not a special command) The HSMCI Argument Register (HSMCI_ARGR) contains the argument field of the command. To send a command, the user must perform the following steps:  Fill the HSMCI_ARGR with the command argument.  Set the HSMCI_CMDR (see Table 36-7). The command is sent immediately after writing the HSMCI_CMDR. While the card maintains a busy indication (at the end of a STOP_TRANSMISSION command CMD12, for example), a new command shall not be sent. The NOTBUSY flag in the HSMCI Status Register (HSMCI_SR) is asserted when the card releases the busy indication. 780 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

If the command requires a response, it can be read in the HSMCI Response Register (HSMCI_RSPR). The response size can be from 48 bits up to 136 bits depending on the command. The HSMCI embeds an error detection to prevent any corrupted data during the transfer. The following flowchart shows how to send a command to the card and read the response if needed. In this example, the status register bits are polled but setting the appropriate bits in the HSMCI Interrupt Enable Register (HSMCI_IER) allows using an interrupt method. SAM9M11 [DATASHEET] 781 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 36-7. Command/Response Functional Flow Diagram Set the command argument HSMCI_ARGR = Argument(1) Set the command HSMCI_CMDR = Command Read HSMCI_SR 0 Wait for command ready status flag CMDRDY 1 Yes Check error bits in the status register (1) Status error flags? (1) RETURN ERROR Read response if required No Does the command involve a busy indication? RETURN OK Read HSMCI_SR 0 NOTBUSY 1 RETURN OK Notes: 1. If the command is SEND_OP_COND, the CRC error flag is always present (refer to R3 response in the High Speed MultiMedia Card specification). 782 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.8.2 Data Transfer Operation The High Speed MultiMedia Card allows several read/write operations (single block, multiple blocks, stream, etc.). These kinds of transfer can be selected setting the Transfer Type (TRTYP) field in the HSMCI Command Register (HSMCI_CMDR). These operations can be done using the features of the DMA Controller. In all cases, the block length (BLKLEN field) must be defined either in the HSMCI_MR, or in the HSMCI Block Register (HSMCI_BLKR). This field determines the size of the data block. Consequent to MMC Specification 3.1, two types of multiple block read (or write) transactions are defined (the host can use either one at any time):  Open-ended/Infinite Multiple block read (or write): The number of blocks for the read (or write) multiple block operation is not defined. The card will continuously transfer (or program) data blocks until a stop transmission command is received.  Multiple block read (or write) with pre-defined block count (since version 3.1 and higher): The card will transfer (or program) the requested number of data blocks and terminate the transaction. The stop command is not required at the end of this type of multiple block read (or write), unless terminated with an error. In order to start a multiple block read (or write) with pre-defined block count, the host must correctly program the HSMCI_BLKR, otherwise, the card will start an open-ended multiple block read. The BCNT field of the HSMCI_BLKR defines the number of blocks to transfer (from 1 to 65535 blocks). Programming the value 0 in the BCNT field corresponds to an infinite block transfer. 36.8.3 Read Operation The following flowchart (Figure 36-8) shows how to read a single block with or without use of DMAC facilities. In this example, a polling method is used to wait for the end of read. Similarly, the user can configure the HSMCI_IER to trigger an interrupt at the end of read. SAM9M11 [DATASHEET] 783 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 36-8. Read Functional Flow Diagram Send SELECT/DESELECT_CARD (1) command to select the card (1) Send SET_BLOCKLEN command No Yes Read with DMAC Reset the DMAEN bit HSMCI_DMA &= ~DMAEN Set the DMAEN bit Set the block length (in bytes) HSMCI_DMA |= DMAEN HSMCI_MR l= (BlockLength<<16) (2) Set the block length (in bytes) (2) Set the block count (if neccessary) HSMCI_BLKR |= (BlockLength << 16) HSMCI_BLKR l= (BlockCount<<0) Send READ_SINGLE_BLOCK Configure the DMA channel X (1) command DMAC_SADDRx = Data Address DMAC_BTSIZE = BlockLength/4 DMACHEN[X] = TRUE Number of words to read = BlockLength/4 Send READ_SINGLE_BLOCK (1) command Yes Number of words to read = 0 ? Read status register HSMCI_SR No Read status register HSMCI_SR Poll the bit Yes XFRDONE = 0? Poll the bit Yes RXRDY = 0? No No RETURN Read data = HSMCI_RDR Number of words to read = Number of words to read -1 RETURN Notes: 1. It is assumed that this command has been correctly sent (see Figure 36-7). 2. This field is also accessible in the HSMCI Block Register (HSMCI_BLKR). 784 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.8.4 Write Operation In write operation, the HSMCI Mode Register (HSMCI_MR) is used to define the padding value when writing non- multiple block size. If the bit PADV is 0, then 0x00 value is used when padding data, otherwise 0xFF is used. If set, the bit DMAEN in the HSMCI DMA Configuration Register (HSMCI_DMA) enables DMA transfer. The following flowchart (Figure 36-9) shows how to write a single block with or without use of DMA facilities. Polling or interrupt method can be used to wait for the end of write according to the contents of the HSMCI Interrupt Mask Register (HSMCI_IMR). SAM9M11 [DATASHEET] 785 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 36-9. Write Functional Flow Diagram Send SELECT/DESELECT_CARD (1) command to select the card (1) Send SET_BLOCKLEN command No Yes Write using DMAC Reset theDMAEN bit Set the DMAEN bit HSMCI_DMA &= ~DMAEN HSMCI_DMA |= DMAEN Set the block length (in bytes) (2) Set the block length (in bytes) HSMCI_MR |= (BlockLength) <<16) (2) HSMCI_BLKR |= (BlockLength << 16) Set the block count (if necessary) HSMCI_BLKR |= (BlockCount << 0) Send WRITE_SINGLE_BLOCK Send WRITE_SINGLE_BLOCK command(1) command(1) Configure the DMA channel X Number of words to write = BlockLength/4 DMAC_DADDRx = Data Address to write DMAC_BTSIZE = BlockLength/4 DMAC_CHEN[X] = TRUE Yes Number of words to write = 0 ? Read status register HSMCI_SR No Read status register HSMCI_SR Poll the bit Yes XFRDONE = 0? Poll the bit Yes TXRDY = 0? No No HSMCI_TDR = Data to write RETURN Number of words to write = Number of words to write -1 RETURN Notes: 1. It is assumed that this command has been correctly sent (see Figure 36-7). 2. This field is also accessible in the HSMCI Block Register (HSMCI_BLKR). 786 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The following flowchart (Figure 36-10) shows how to manage read multiple block and write multiple block transfers with the DMA Controller. Polling or interrupt method can be used to wait for the end of write according to the contents of the HSMCI_IMR. Figure 36-10. Read Multiple Block and Write Multiple Block Send SELECT/DESELECT_CARD (1) command to select the card (1) Send SET_BLOCKLEN command Set the block length HSMCI_MR |= (BlockLength << 16) Set the DMAEN bit HSMCI_DMA |= DMAEN Send WRITE_MULTIPLE_BLOCK or (1) READ_MULTIPLE_BLOCK command Configure the HDMA channel X DMAC_SADDRx and DMAC_DADDRx DMAC_BTSIZE = BlockLength/4 DMAC_CHEN[X] = TRUE Read status register DMAC_EBCISR and Poll Bit CBTC[X] (2) Yes New Buffer ? No Read status register HSMCI_SR and Poll Bit FIFOEMPTY Send STOP_TRANSMISSION (1) command Poll the bit No XFRDONE = 1 Yes RETURN Notes: 1. It is assumed that this command has been correctly sent (see Figure 36-7). 2. Handle errors reported in HSMCI_SR. SAM9M11 [DATASHEET] 787 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.8.5 WRITE_SINGLE_BLOCK Operation using DMA Controller 1. Wait until the current command execution has successfully terminated. c. Check that CMDRDY and NOTBUSY fields are asserted in HSMCI_SR 2. Program the block length in the card. This value defines the value block_length. 3. Program the block length in the HSMCI configuration register with block_length value. 4. Program HSMCI_DMA register with the following fields: ̶ OFFSET field with dma_offset. ̶ CHKSIZE is user defined and set according to DMAC_DCSIZE. ̶ DMAEN is set to true to enable DMA hardware handshaking in the HSMCI. This bit was previously set to false. 5. Issue a WRITE_SINGLE_BLOCK command writing HSMCI_ARGR then HSMCI_CMDR. 6. Program the DMA Controller. a. Read the channel Register to choose an available (disabled) channel. b. Clear any pending interrupts on the channel from the previous DMAC transfer by reading the DMAC_EBCISR. c. Program the channel registers. d. The DMAC_SADDRx register for channel x must be set to the location of the source data. When the first data location is not word aligned, the two LSB bits define the temporary value called dma_offset. The two LSB bits of DMAC_SADDRx must be set to 0. e. The DMAC_DADDRx register for channel x must be set with the starting address of the HSMCI_FIFO address. f. Program DMAC_CTRLAx register of channel x with the following field’s values: –DST_WIDTH is set to WORD. –SRC_WIDTH is set to WORD. –DCSIZE must be set according to the value of HSMCI_DMA.CHKSIZE field. –BTSIZE is programmed with CEILING((block_length + dma_offset) / 4), where the ceiling function is the function that returns the smallest integer not less than x. g. Program DMAC_CTRLBx register for channel x with the following field’s values: –DST_INCR is set to INCR, the block_length value must not be larger than the HSMCI_FIFO aperture. –SRC_INCR is set to INCR. –FC field is programmed with memory to peripheral flow control mode. –both DST_DSCR and SRC_DSCR are set to 1 (descriptor fetch is disabled). –DIF and SIF are set with their respective layer ID. If SIF is different from DIF, the DMA controller is able to prefetch data and write HSMCI simultaneously. h. Program DMAC_CFGx register for channel x with the following field’s values: –FIFOCFG defines the watermark of the DMAC channel FIFO. –DST_H2SEL is set to true to enable hardware handshaking on the destination. –DST_PER is programmed with the hardware handshaking ID of the targeted HSMCI Host Controller. i. Enable Channel x, writing one to DMAC_CHER[x]. The DMAC is ready and waiting for request. 7. Wait for XFRDONE in HSMCI_SR. 788 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.8.6 READ_SINGLE_BLOCK Operation using DMA Controller 36.8.6.1 Block Length is Multiple of 4 1. Wait until the current command execution has successfully completed. a. Check that CMDRDY and NOTBUSY are asserted in HSMCI_SR. 2. Program the block length in the card. This value defines the value block_length. 3. Program the block length in the HSMCI configuration register with block_length value. 4. Set RDPROOF bit in HSMCI_MR to avoid overflow. 5. Program HSMCI_DMA register with the following fields: ̶ ROPT field is set to 0. ̶ OFFSET field is set to 0. ̶ CHKSIZE is user defined. ̶ DMAEN is set to true to enable DMAC hardware handshaking in the HSMCI. This bit was previously set to false. 6. Issue a READ_SINGLE_BLOCK command. 7. Program the DMA controller. a. Read the channel Register to choose an available (disabled) channel. b. Clear any pending interrupts on the channel from the previous DMA transfer by reading the DMAC_EBCISR. c. Program the channel registers. d. The DMAC_SADDRx register for channel x must be set with the starting address of the HSMCI_FIFO address. e. The DMAC_DADDRx register for channel x must be word aligned. f. Program DMAC_CTRLAx register of channel x with the following field’s values: –DST_WIDTH is set to WORD. –SRC_WIDTH is set to WORD. –SCSIZE must be set according to the value of HSMCI_DMA.CHKSIZE field. –BTSIZE is programmed with block_length/4. g. Program DMAC_CTRLBx register for channel x with the following field’s values: –DST_INCR is set to INCR. –SRC_INCR is set to INCR. –FC field is programmed with peripheral to memory flow control mode. –both DST_DSCR and SRC_DSCR are set to 1 (descriptor fetch is disabled). –DIF and SIF are set with their respective layer ID. If SIF is different from DIF, the DMA controller is able to prefetch data and write HSMCI simultaneously. h. Program DMAC_CFGx register for channel x with the following field’s values: –FIFOCFG defines the watermark of the DMA channel FIFO. –SRC_H2SEL is set to true to enable hardware handshaking on the destination. –SRC_PER is programmed with the hardware handshaking ID of the targeted HSMCI Host Controller. –Enable Channel x, writing one to DMAC_CHER[x]. The DMAC is ready and waiting for request. 8. Wait for XFRDONE in HSMCI_SR. SAM9M11 [DATASHEET] 789 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.8.6.2 Block Length is Not Multiple of 4 and Padding Not Used (ROPT field in HSMCI_DMA register set to 0) In the previous DMA transfer flow (block length multiple of 4), the DMA controller is configured to use only WORD AHB access. When the block length is no longer a multiple of 4 this is no longer true. The DMA controller is programmed to copy exactly the block length number of bytes using 2 transfer descriptors. 1. Use the previous step until READ_SINGLE_BLOCK then 2. Program the DMA controller to use a two descriptors linked list. a. Read the channel Register to choose an available (disabled) channel. b. Clear any pending interrupts on the channel from the previous DMA transfer by reading the DMAC_EBCISR. c. Program the channel registers in the Memory for the first descriptor. This descriptor will be word ori- ented. This descriptor is referred to as LLI_W, standing for LLI word oriented transfer. d. The LLI_W.DMAC_SADDRx field in memory must be set with the starting address of the HSMCI_FIFO address. e. The LLI_W.DMAC_DADDRx field in the memory must be word aligned. f. Program LLI_W.DMAC_CTRLAx with the following field’s values: –DST_WIDTH is set to WORD. –SRC_WIDTH is set to WORD. –SCSIZE must be set according to the value of HSMCI_DMA.CHKSIZE field. –BTSIZE is programmed with block_length/4. If BTSIZE is zero, this descriptor is skipped later. g. Program LLI_W.DMAC_CTRLBx with the following field’s values: –DST_INCR is set to INCR –SRC_INCR is set to INCR –FC field is programmed with peripheral to memory flow control mode. –SRC_DSCR is set to zero. (descriptor fetch is enabled for the SRC) –DST_DSCR is set to one. (descriptor fetch is disabled for the DST) –DIF and SIF are set with their respective layer ID. If SIF is different from DIF, DMA controller is able to prefetch data and write HSMCI simultaneously. h. Program LLI_W.DMAC_CFGx register for channel x with the following field’s values: –FIFOCFG defines the watermark of the DMA channel FIFO. –DST_REP is set to zero meaning that address are contiguous. –SRC_H2SEL is set to true to enable hardware handshaking on the destination. –SRC_PER is programmed with the hardware handshaking ID of the targeted HSMCI Host Controller. i. Program LLI_W.DMAC_DSCRx with the address of LLI_B descriptor. And set DSCRx_IF to the AHB Layer ID. This operation actually links the Word oriented descriptor on the second byte oriented descriptor. When block_length[1:0] is equal to 0 (multiple of 4) LLI_W.DMAC_DSCRx points to 0, only LLI_W is relevant. j. Program the channel registers in the Memory for the second descriptor. This descriptor will be byte oriented. This descriptor is referred to as LLI_B, standing for LLI Byte oriented. k. The LLI_B.DMAC_SADDRx field in memory must be set with the starting address of the HSMCI_FIFO address. l. The LLI_B.DMAC_DADDRx is not relevant if previous word aligned descriptor was enabled. If 1, 2 or 3 bytes are transferred that address is user defined and not word aligned. m. Program LLI_B.DMAC_CTRLAx with the following field’s values: –DST_WIDTH is set to BYTE. 790 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

–SRC_WIDTH is set to BYTE. –SCSIZE must be set according to the value of HSMCI_DMA.CHKSIZE field. –BTSIZE is programmed with block_length[1:0]. (last 1, 2, or 3 bytes of the buffer). n. Program LLI_B.DMAC_CTRLBx with the following field’s values: –DST_INCR is set to INCR –SRC_INCR is set to INCR –FC field is programmed with peripheral to memory flow control mode. –Both SRC_DSCR and DST_DSCR are set to 1 (descriptor fetch is disabled) or Next descriptor location points to 0. –DIF and SIF are set with their respective layer ID. If SIF is different from DIF, DMA Controller is able to prefetch data and write HSMCI simultaneously. o. Program LLI_B.DMAC_CFGx memory location for channel x with the following field’s values: –FIFOCFG defines the watermark of the DMA channel FIFO. –SRC_H2SEL is set to true to enable hardware handshaking on the destination. –SRC_PER is programmed with the hardware handshaking ID of the targeted HSMCI Host Controller. p. Program LLI_B.DMAC_DSCR with 0. q. Program DMAC_CTRLBx register for channel x with 0. its content is updated with the LLI fetch operation. r. Program DMAC_DSCRx with the address of LLI_W if block_length greater than 4 else with address of LLI_B. s. Enable Channel x writing one to DMAC_CHER[x]. The DMAC is ready and waiting for request. 3. Wait for XFRDONE in HSMCI_SR. 36.8.6.3 Block Length is Not Multiple of 4, with Padding Value (ROPT field in HSMCI_DMA register set to 1) When the ROPT field is set to one, The DMA Controller performs only WORD access on the bus to transfer a non- multiple of 4 block length. Unlike previous flow, in which the transfer size is rounded to the nearest multiple of 4. 1. Program the HSMCI Interface, see previous flow. ̶ ROPT field is set to 1. 2. Program the DMA Controller a. Read the channel Register to choose an available (disabled) channel. b. Clear any pending interrupts on the channel from the previous DMA transfer by reading the DMAC_EBCISR. c. Program the channel registers. d. The DMAC_SADDRx register for channel x must be set with the starting address of the HSMCI_FIFO address. e. The DMAC_DADDRx register for channel x must be word aligned. f. Program DMAC_CTRLAx register of channel x with the following field’s values: –DST_WIDTH is set to WORD –SRC_WIDTH is set to WORD –SCSIZE must be set according to the value of HSMCI_DMA.CHKSIZE field. –BTSIZE is programmed with CEILING(block_length/4). g. Program DMAC_CTRLBx register for channel x with the following field’s values: –DST_INCR is set to INCR –SRC_INCR is set to INCR SAM9M11 [DATASHEET] 791 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

–FC field is programmed with peripheral to memory flow control mode. –both DST_DSCR and SRC_DSCR are set to 1. (descriptor fetch is disabled) –DIF and SIF are set with their respective layer ID. If SIF is different from DIF, the DMA Controller is able to prefetch data and write HSMCI simultaneously. h. Program DMAC_CFGx register for channel x with the following field’s values: –FIFOCFG defines the watermark of the DMA channel FIFO. –SRC_H2SEL is set to true to enable hardware handshaking on the destination. –SRC_PER is programmed with the hardware handshaking ID of the targeted HSMCI Host Controller. –Enable Channel x writing one to DMAC_CHER[x]. The DMAC is ready and waiting for request. 3. Wait for XFRDONE in HSMCI_SR. 36.8.7 WRITE_MULTIPLE_BLOCK 36.8.7.1 One Block per Descriptor 1. Wait until the current command execution has successfully terminated. a. Check that CMDRDY and NOTBUSY are asserted in HSMCI_SR. 2. Program the block length in the card. This value defines the value block_length. 3. Program the block length in the HSMCI configuration register with block_length value. 4. Program HSMCI_DMA register with the following fields: ̶ OFFSET field with dma_offset. ̶ CHKSIZE is user defined. ̶ DMAEN is set to true to enable DMAC hardware handshaking in the HSMCI. This bit was previously set to false. 5. Issue a WRITE_MULTIPLE_BLOCK command. 6. Program the DMA Controller to use a list of descriptors. Each descriptor transfers one block of data. Block n of data is transferred with descriptor LLI(n). a. Read the channel Register to choose an available (disabled) channel. b. Clear any pending interrupts on the channel from the previous DMAC transfer by reading the DMAC_EBCISR. c. Program a List of descriptors. d. The LLI(n).DMAC_SADDRx memory location for channel x must be set to the location of the source data. When the first data location is not word aligned, the two LSB bits define the temporary value called dma_offset. The two LSB bits of LLI(n).DMAC_SADDRx must be set to 0. e. The LLI(n).DMAC_DADDRx register for channel x must be set with the starting address of the HSMCI_FIFO address. f. Program LLI(n).DMAC_CTRLAx register of channel x with the following field’s values: –DST_WIDTH is set to WORD. –SRC_WIDTH is set to WORD. –DCSIZE must be set according to the value of HSMCI_DMA.CHKSIZE field. –BTSIZE is programmed with CEILING((block_length + dma_offset)/4). g. Program LLI(n).DMAC_CTRLBx register for channel x with the following field’s values: –DST_INCR is set to INCR. –SRC_INCR is set to INCR. –DST_DSCR is set to 0 (fetch operation is enabled for the destination). 792 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

–SRC_DSCR is set to 1 (source address is contiguous). –FC field is programmed with memory to peripheral flow control mode. –Both DST_DSCR and SRC_DSCR are set to 1 (descriptor fetch is disabled). –DIF and SIF are set with their respective layer ID. If SIF is different from DIF, DMA Controller is able to prefetch data and write HSMCI simultaneously. h. Program LLI(n).DMAC_CFGx register for channel x with the following field’s values: –FIFOCFG defines the watermark of the DMA channel FIFO. –DST_H2SEL is set to true to enable hardware handshaking on the destination. –SRC_REP is set to 0. (contiguous memory access at block boundary) –DST_PER is programmed with the hardware handshaking ID of the targeted HSMCI Host Controller. i. If LLI(n) is the last descriptor, then LLI(n).DSCR points to 0 else LLI(n) points to the start address of LLI(n+1). j. Program DMAC_CTRLBx for channel register x with 0. Its content is updated with the LLI fetch operation. k. Program DMAC_DSCRx for channel register x with the address of the first descriptor LLI(0). l. Enable Channel x writing one to DMAC_CHER[x]. The DMA is ready and waiting for request. 7. Poll CBTC[x] bit in the DMAC_EBCISR. 8. If a new list of buffers shall be transferred, repeat step 6. Check and handle HSMCI errors. 9. Poll FIFOEMPTY field in the HSMCI_SR. 10. Send The STOP_TRANSMISSION command writing HSMCI_ARGR then HSMCI_CMDR. 11. Wait for XFRDONE in HSMCI_SR. 36.8.8 READ_MULTIPLE_BLOCK 36.8.8.1 Block Length is a Multiple of 4 1. Wait until the current command execution has successfully terminated. a. Check that CMDRDY and NOTBUSY are asserted in HSMCI_SR. 2. Program the block length in the card. This value defines the value block_length. 3. Program the block length in the HSMCI configuration register with block_length value. 4. Set RDPROOF bit in HSMCI_MR to avoid overflow. 5. Program HSMCI_DMA register with the following fields: ̶ ROPT field is set to 0. ̶ OFFSET field is set to 0. ̶ CHKSIZE is user defined. ̶ DMAEN is set to true to enable DMAC hardware handshaking in the HSMCI. This bit was previously set to false. 6. Issue a READ_MULTIPLE_BLOCK command. 7. Program the DMA Controller to use a list of descriptors: SAM9M11 [DATASHEET] 793 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

a. Read the channel Register to choose an available (disabled) channel. b. Clear any pending interrupts on the channel from the previous DMA transfer by reading the DMAC_EBCISR. c. Program the channel registers in the Memory with the first descriptor. This descriptor will be word ori- ented. This descriptor is referred to as LLI_W(n), standing for LLI word oriented transfer for block n. d. The LLI_W(n).DMAC_SADDRx field in memory must be set with the starting address of the HSMCI_FIFO address. e. The LLI_W(n).DMAC_DADDRx field in the memory must be word aligned. f. Program LLI_W(n).DMAC_CTRLAx with the following field’s values: –DST_WIDTH is set to WORD –SRC_WIDTH is set to WORD –SCSIZE must be set according to the value of HSMCI_DMA.CHKSIZE field. –BTSIZE is programmed with block_length/4. g. Program LLI_W(n).DMAC_CTRLBx with the following field’s values: –DST_INCR is set to INCR. –SRC_INCR is set to INCR. –FC field is programmed with peripheral to memory flow control mode. –SRC_DSCR is set to 0 (descriptor fetch is enabled for the SRC). –DST_DSCR is set to TRUE (descriptor fetch is disabled for the DST). –DIF and SIF are set with their respective layer ID. If SIF is different from DIF, the DMA Controller is able to prefetch data and write HSMCI simultaneously. h. Program LLI_W(n).DMAC_CFGx register for channel x with the following field’s values: –FIFOCFG defines the watermark of the DMA channel FIFO. –DST_REP is set to zero. Addresses are contiguous. –SRC_H2SEL is set to true to enable hardware handshaking on the destination. –SRC_PER is programmed with the hardware handshaking ID of the targeted HSMCI Host Controller. i. Program LLI_W(n).DMAC_DSCRx with the address of LLI_W(n+1) descriptor. And set the DSCRx_IF to the AHB Layer ID. This operation actually links descriptors together. If LLI_W(n) is the last descrip- tor then LLI_W(n).DMAC_DSCRx points to 0. j. Program DMAC_CTRLBx register for channel x with 0. its content is updated with the LLI Fetch operation. k. Program DMAC_DSCRx register for channel x with the address of LLI_W(0). l. Enable Channel x writing one to DMAC_CHER[x]. The DMA is ready and waiting for request. 8. Poll CBTC[x] bit in the DMAC_EBCISR. 9. If a new list of buffer shall be transferred repeat step 6. Check and handle HSMCI errors. 10. Poll FIFOEMPTY field in the HSMCI_SR. 11. Send The STOP_TRANSMISSION command writing the HSMCI_ARGR then the HSMCI_CMDR. 12. Wait for XFRDONE in HSMCI_SR. 36.8.8.2 Block Length is Not Multiple of 4. (ROPT field in HSMCI_DMA register set to 0) Two DMA Transfer descriptors are used to perform the HSMCI block transfer. 1. Use the previous step to configure the HSMCI to perform a READ_MULTIPLE_BLOCK command. 2. Issue a READ_MULTIPLE_BLOCK command. 3. Program the DMA Controller to use a list of descriptors. 794 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

a. Read the channel register to choose an available (disabled) channel. b. Clear any pending interrupts on the channel from the previous DMAC transfer by reading the DMAC_EBCISR. c. For every block of data repeat the following procedure: d. Program the channel registers in the Memory for the first descriptor. This descriptor will be word ori- ented. This descriptor is referred to as LLI_W(n) standing for LLI word oriented transfer for block n. e. The LLI_W(n).DMAC_SADDRx field in memory must be set with the starting address of the HSMCI_FIFO address. f. The LLI_W(n).DMAC_DADDRx field in the memory must be word aligned. g. Program LLI_W(n).DMAC_CTRLAx with the following field’s values: –DST_WIDTH is set to WORD. –SRC_WIDTH is set to WORD. –SCSIZE must be set according to the value of HSMCI_DMA.CHKSIZE field. –BTSIZE is programmed with block_length/4. If BTSIZE is zero, this descriptor is skipped later. h. Program LLI_W(n).DMAC_CTRLBx with the following field’s values: –DST_INCR is set to INCR. –SRC_INCR is set to INCR. –FC field is programmed with peripheral to memory flow control mode. –SRC_DSCR is set to 0 (descriptor fetch is enabled for the SRC). –DST_DSCR is set to TRUE (descriptor fetch is disabled for the DST). –DIF and SIF are set with their respective layer ID. If SIF is different from DIF, the DMA Controller is able to prefetch data and write HSMCI simultaneously. i. Program LLI_W(n).DMAC_CFGx register for channel x with the following field’s values: –FIFOCFG defines the watermark of the DMA channel FIFO. –DST_REP is set to zero. Address are contiguous. –SRC_H2SEL is set to true to enable hardware handshaking on the destination. –SRC_PER is programmed with the hardware handshaking ID of the targeted HSMCI Host Controller. j. Program LLI_W(n).DMAC_DSCRx with the address of LLI_B(n) descriptor. And set the DSCRx_IF to the AHB Layer ID. This operation actually links the Word oriented descriptor on the second byte ori- ented descriptor. When block_length[1:0] is equal to 0 (multiple of 4) LLI_W(n).DMAC_DSCRx points to 0, only LLI_W(n) is relevant. k. Program the channel registers in the Memory for the second descriptor. This descriptor will be byte oriented. This descriptor is referred to as LLI_B(n), standing for LLI Byte oriented. l. The LLI_B(n).DMAC_SADDRx field in memory must be set with the starting address of the HSMCI_FIFO address. m. The LLI_B(n).DMAC_DADDRx is not relevant if previous word aligned descriptor was enabled. If 1, 2 or 3 bytes are transferred, that address is user defined and not word aligned. n. Program LLI_B(n).DMAC_CTRLAx with the following field’s values: –DST_WIDTH is set to BYTE. –SRC_WIDTH is set to BYTE. –SCSIZE must be set according to the value of HSMCI_DMA.CHKSIZE field. –BTSIZE is programmed with block_length[1:0]. (last 1, 2, or 3 bytes of the buffer). o. Program LLI_B(n).DMAC_CTRLBx with the following field’s values: –DST_INCR is set to INCR. SAM9M11 [DATASHEET] 795 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

–SRC_INCR is set to INCR. –FC field is programmed with peripheral to memory flow control mode. –Both SRC_DSCR and DST_DSCR are set to 1 (descriptor fetch is disabled) or Next descriptor location points to 0. –DIF and SIF are set with their respective layer ID. If SIF is different from DIF, the DMA Controller is able to prefetch data and write HSMCI simultaneously. p. Program LLI_B(n).DMAC_CFGx memory location for channel x with the following field’s values: –FIFOCFG defines the watermark of the DMAC channel FIFO. –SRC_H2SEL is set to true to enable hardware handshaking on the destination. –SRC_PER is programmed with the hardware handshaking ID of the targeted HSMCI Host Controller q. Program LLI_B(n).DMAC_DSCR with address of descriptor LLI_W(n+1). If LLI_B(n) is the last descriptor, then program LLI_B(n).DMAC_DSCR with 0. r. Program DMAC_CTRLBx register for channel x with 0, its content is updated with the LLI Fetch operation. s. Program DMAC_DSCRx with the address of LLI_W(0) if block_length is greater than 4 else with address of LLI_B(0). t. Enable Channel x writing one to DMAC_CHER[x]. The DMAC is ready and waiting for request. 4. Enable DMADONE interrupt in the HSMCI_IER. 5. Poll CBTC[x] bit in the DMAC_EBCISR. 6. If a new list of buffers shall be transferred, repeat step 7. Check and handle HSMCI errors. 7. Poll FIFOEMPTY field in the HSMCI_SR. 8. Send The STOP_TRANSMISSION command writing HSMCI_ARGR then HSMCI_CMDR. 9. Wait for XFRDONE in HSMCI_SR. 36.8.8.3 Block Length is Not a Multiple of 4. (ROPT field in HSMCI_DMA register set to 1) One DMA Transfer descriptor is used to perform the HSMCI block transfer, the DMA writes a rounded up value to the nearest multiple of 4. 1. Use the previous step to configure the HSMCI to perform a READ_MULTIPLE_BLOCK. 2. Set the ROPT field to 1 in the HSMCI_DMA register. 3. Issue a READ_MULTIPLE_BLOCK command. 4. Program the DMA controller to use a list of descriptors: a. Read the channel Register to choose an available (disabled) channel. b. Clear any pending interrupts on the channel from the previous DMAC transfer by reading the DMAC_EBCISR. c. Program the channel registers in the Memory with the first descriptor. This descriptor will be word ori- ented. This descriptor is referred to as LLI_W(n), standing for LLI word oriented transfer for block n. d. The LLI_W(n).DMAC_SADDRx field in memory must be set with the starting address of the HSMCI_FIFO address. e. The LLI_W(n).DMAC_DADDRx field in the memory must be word aligned. f. Program LLI_W(n).DMAC_CTRLAx with the following field’s values: –DST_WIDTH is set to WORD. –SRC_WIDTH is set to WORD. –SCSIZE must be set according to the value of HSMCI_DMA.CHKSIZE field. –BTSIZE is programmed with Ceiling(block_length/4). 796 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

g. Program LLI_W(n).DMAC_CTRLBx with the following field’s values: –DST_INCR is set to INCR –SRC_INCR is set to INCR –FC field is programmed with peripheral to memory flow control mode. –SRC_DSCR is set to 0. (descriptor fetch is enabled for the SRC) –DST_DSCR is set to TRUE. (descriptor fetch is disabled for the DST) –DIF and SIF are set with their respective layer ID. If SIF is different from DIF, the DMA Controller is able to prefetch data and write HSMCI simultaneously. h. Program LLI_W(n).DMAC_CFGx register for channel x with the following field’s values: –FIFOCFG defines the watermark of the DMA channel FIFO. –DST_REP is set to zero. Address are contiguous. –SRC_H2SEL is set to true to enable hardware handshaking on the destination. –SRC_PER is programmed with the hardware handshaking ID of the targeted HSMCI Host Controller. i. Program LLI_W(n).DMAC_DSCRx with the address of LLI_W(n+1) descriptor. And set the DSCRx_IF to the AHB Layer ID. This operation actually links descriptors together. If LLI_W(n) is the last descrip- tor then LLI_W(n).DMAC_DSCRx points to 0. j. Program DMAC_CTRLBx register for channel x with 0. its content is updated with the LLI Fetch operation. k. Program DMAC_DSCRx register for channel x with the address of LLI_W(0). l. Enable Channel x writing one to DMAC_CHER[x]. The DMAC is ready and waiting for request. 5. Poll CBTC[x] bit in the DMAC_EBCISR. 6. If a new list of buffers shall be transferred repeat step 7. Check and handle HSMCI errors. 7. Poll FIFOEMPTY field in the HSMCI_SR. 8. Send The STOP_TRANSMISSION command writing the HSMCI_ARGR then the HSMCI_CMDR. 9. Wait for XFRDONE in HSMCI_SR. 36.9 SD/SDIO Card Operation The High Speed MultiMedia Card Interface allows processing of SD Memory (Secure Digital Memory Card) and SDIO (SD Input Output) Card commands. SD/SDIO cards are based on the Multi Media Card (MMC) format, but are physically slightly thicker and feature higher data transfer rates, a lock switch on the side to prevent accidental overwriting and security features. The physical form factor, pin assignment and data transfer protocol are forward-compatible with the High Speed MultiMedia Card with some additions. SD slots can actually be used for more than flash memory cards. Devices that support SDIO can use small devices designed for the SD form factor, such as GPS receivers, Wi-Fi or Bluetooth adapters, modems, barcode readers, IrDA adapters, FM radio tuners, RFID readers, digital cameras and more. SD/SDIO is covered by numerous patents and trademarks, and licensing is only available through the Secure Digital Card Association. The SD/SDIO Card communication is based on a 9-pin interface (Clock, Command, 4xData and 3 x Power lines). The communication protocol is defined as a part of this specification. The main difference between the SD/SDIO Card and the High Speed MultiMedia Card is the initialization process. The SD/SDIO Card Register (HSMCI_SDCR) allows selection of the Card Slot and the data bus width. SAM9M11 [DATASHEET] 797 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The SD/SDIO Card bus allows dynamic configuration of the number of data lines. After power up, by default, the SD/SDIO Card uses only DAT0 for data transfer. After initialization, the host can change the bus width (number of active data lines). 36.9.1 SDIO Data Transfer Type SDIO cards may transfer data in either a multi-byte (1 to 512 bytes) or an optional block format (1 to 511 blocks), while the SD memory cards are fixed in the block transfer mode. The TRTYP field in the HSMCI Command Register (HSMCI_CMDR) allows to choose between SDIO Byte or SDIO Block transfer. The number of bytes/blocks to transfer is set through the BCNT field in the HSMCI Block Register (HSMCI_BLKR). In SDIO Block mode, the field BLKLEN must be set to the data block size while this field is not used in SDIO Byte mode. An SDIO Card can have multiple I/O or combined I/O and memory (called Combo Card). Within a multi-function SDIO or a Combo card, there are multiple devices (I/O and memory) that share access to the SD bus. In order to allow the sharing of access to the host among multiple devices, SDIO and combo cards can implement the optional concept of suspend/resume (Refer to the SDIO Specification for more details). To send a suspend or a resume command, the host must set the SDIO Special Command field (IOSPCMD) in the HSMCI Command Register. 36.9.2 SDIO Interrupts Each function within an SDIO or Combo card may implement interrupts (Refer to the SDIO Specification for more details). In order to allow the SDIO card to interrupt the host, an interrupt function is added to a pin on the DAT[1] line to signal the card’s interrupt to the host. An SDIO interrupt on each slot can be enabled through the HSMCI Interrupt Enable Register. The SDIO interrupt is sampled regardless of the currently selected slot. 36.10 CE-ATA Operation CE-ATA maps the streamlined ATA command set onto the MMC interface. The ATA task file is mapped onto MMC register space. CE-ATA utilizes five MMC commands:  GO_IDLE_STATE (CMD0): used for hard reset.  STOP_TRANSMISSION (CMD12): causes the ATA command currently executing to be aborted.  FAST_IO (CMD39): Used for single register access to the ATA taskfile registers, 8 bit access only.  RW_MULTIPLE_REGISTERS (CMD60): used to issue an ATA command or to access the control/status registers.  RW_MULTIPLE_BLOCK (CMD61): used to transfer data for an ATA command. CE-ATA utilizes the same MMC command sequences for initialization as traditional MMC devices. 36.10.1 Executing an ATA Polling Command 1. Issue READ_DMA_EXT with RW_MULTIPLE_REGISTER (CMD60) for 8kB of DATA. 2. Read the ATA status register until DRQ is set. 3. Issue RW_MULTIPLE_BLOCK (CMD61) to transfer DATA. 4. Read the ATA status register until DRQ && BSY are set to 0. 36.10.2 Executing an ATA Interrupt Command 1. Issue READ_DMA_EXT with RW_MULTIPLE_REGISTER (CMD60) for 8kB of DATA with nIEN field set to zero to enable the command completion signal in the device. 2. Issue RW_MULTIPLE_BLOCK (CMD61) to transfer DATA. 3. Wait for Completion Signal Received Interrupt. 798 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.10.3 Aborting an ATA Command If the host needs to abort an ATA command prior to the completion signal it must send a special command to avoid potential collision on the command line. The SPCMD field of the HSMCI_CMDR must be set to 3 to issue the CE- ATA completion Signal Disable Command. 36.10.4 CE-ATA Error Recovery Several methods of ATA command failure may occur, including:  No response to an MMC command, such as RW_MULTIPLE_REGISTER (CMD60).  CRC is invalid for an MMC command or response.  CRC16 is invalid for an MMC data packet.  ATA Status register reflects an error by setting the ERR bit to one.  The command completion signal does not arrive within a host specified time out period. Error conditions are expected to happen infrequently. Thus, a robust error recovery mechanism may be used for each error event. The recommended error recovery procedure after a timeout is:  Issue the command completion signal disable if nIEN was cleared to zero and the RW_MULTIPLE_BLOCK (CMD61) response has been received.  Issue STOP_TRANSMISSION (CMD12) and successfully receive the R1 response.  Issue a software reset to the CE-ATA device using FAST_IO (CMD39). If STOP_TRANMISSION (CMD12) is successful, then the device is again ready for ATA commands. However, if the error recovery procedure does not work as expected or there is another timeout, the next step is to issue GO_IDLE_STATE (CMD0) to the device. GO_IDLE_STATE (CMD0) is a hard reset to the device and completely resets all device states. Note that after issuing GO_IDLE_STATE (CMD0), all device initialization needs to be completed again. If the CE- ATA device completes all MMC commands correctly but fails the ATA command with the ERR bit set in the ATA Status register, no error recovery action is required. The ATA command itself failed implying that the device could not complete the action requested, however, there was no communication or protocol failure. After the device signals an error by setting the ERR bit to one in the ATA Status register, the host may attempt to retry the command. 36.11 HSMCI Boot Operation Mode 36.11.1 In boot operation mode, the processor can read boot data from the slave (MMC device) by keeping the CMD line low after power-on before issuing CMD1. The data can be read from either the boot area or user area, depending on register setting. Boot Procedure, Processor Mode 1. Configure the HSMCI data bus width programming SDCBUS field in the HSMCI_SDCR. The BOOT_BUS_WIDTH field located in the device Extended CSD register must be set accordingly. 2. Set the byte count to 512 bytes and the block count to the desired number of blocks, writing BLKLEN and BCNT fields of the HSMCI_BLKR. 3. Issue the Boot Operation Request command by writing to the HSMCI_CMDR with SPCMD field set to BOOTREQ, TRDIR set to READ and TRCMD set to “start data transfer”. 4. The BOOT_ACK field located in the HSMCI_CMDR must be set to one, if the BOOT_ACK field of the MMC device located in the Extended CSD register is set to one. 5. Host processor can copy boot data sequentially as soon as the RXRDY flag is asserted. 6. When Data transfer is completed, host processor shall terminate the boot stream by writing the HSMCI_CMDR with SPCMD field set to BOOTEND. SAM9M11 [DATASHEET] 799 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.11.2 Boot Procedure DMA Mode 1. Configure the HSMCI data bus width by programming SDCBUS Field in the HSMCI_SDCR. The BOOT_BUS_WIDTH field in the device Extended CSD register must be set accordingly. 2. Set the byte count to 512 bytes and the block count to the desired number of blocks by writing BLKLEN and BCNT fields of the HSMCI_BLKR. 3. Enable DMA transfer in the HSMCI_DMA register. 4. Configure DMA controller, program the total amount of data to be transferred and enable the relevant channel. 5. Issue the Boot Operation Request command by writing to the HSMCI_CMDR with SPCND set to BOOTREQ, TRDIR set to READ and TRCMD set to “start data transfer”. 6. DMA controller copies the boot partition to the memory. 7. When DMA transfer is completed, host processor shall terminate the boot stream by writing the HSMCI_CMDR with SPCMD field set to BOOTEND. 800 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.12 HSMCI Transfer Done Timings 36.12.1 Definition The XFRDONE flag in the HSMCI_SR indicates exactly when the read or write sequence is finished. 36.12.2 Read Access During a read access, the XFRDONE flag behaves as shown in Figure 36-11. Figure 36-11. XFRDONE During a Read Access CMD line HSMCI read CMD Card response The CMDRDY flag is released 8 tbit after the end of the card response. CMDRDY flag Data 1st Block Last Block Not busy flag XFRDONE flag 36.12.3 Write Access During a write access, the XFRDONE flag behaves as shown in Figure 36-12. Figure 36-12. XFRDONE During a Write Access CMD line HSMCI write CMD Card response CMDRDY flag The CMDRDY flag is released 8 tbit after the end of the card response. D0 D0 is tied by the card D0 is released 1st Block Last Block Data bus - D0 1st Block Last Block Not busy flag XFRDONE flag SAM9M11 [DATASHEET] 801 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.13 Write Protection Registers To prevent any single software error that may corrupt HSMCI behavior, the entire HSMCI address space from address offset 0x000 to 0x00FC can be write-protected by setting the WPEN bit in the “HSMCI Write Protect Mode Register” (HSMCI_WPMR). If a write access to anywhere in the HSMCI address space from address offset 0x000 to 0x00FC is detected, then the WPVS flag in the HSMCI Write Protect Status Register (HSMCI_WPSR) is set and the field WPVSRC indicates in which register the write access has been attempted. The WPVS flag is reset by writing the HSMCI_WPMR with the appropriate access key, WPKEY. The protected registers are:  “HSMCI Mode Register” on page 805  “HSMCI Data Timeout Register” on page 807  “HSMCI SDCard/SDIO Register” on page 808  “HSMCI Completion Signal Timeout Register” on page 813  “HSMCI DMA Configuration Register” on page 827  “HSMCI Configuration Register” on page 828 802 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14 High Speed MultiMediaCard Interface (HSMCI) User Interface Table 36-8. Register Mapping Offset Register Name Access Reset 0x00 Control Register HSMCI_CR Write-only – 0x04 Mode Register HSMCI_MR Read/Write 0x0 0x08 Data Timeout Register HSMCI_DTOR Read/Write 0x0 0x0C SD/SDIO Card Register HSMCI_SDCR Read/Write 0x0 0x10 Argument Register HSMCI_ARGR Read/Write 0x0 0x14 Command Register HSMCI_CMDR Write-only – 0x18 Block Register HSMCI_BLKR Read/Write 0x0 0x1C Completion Signal Timeout Register HSMCI_CSTOR Read/Write 0x0 0x20 Response Register(1) HSMCI_RSPR Read-only 0x0 0x24 Response Register(1) HSMCI_RSPR Read-only 0x0 0x28 Response Register(1) HSMCI_RSPR Read-only 0x0 0x2C Response Register(1) HSMCI_RSPR Read-only 0x0 0x30 Receive Data Register HSMCI_RDR Read-only 0x0 0x34 Transmit Data Register HSMCI_TDR Write-only – 0x38–0x3C Reserved – – – 0x40 Status Register HSMCI_SR Read-only 0xC0E5 0x44 Interrupt Enable Register HSMCI_IER Write-only – 0x48 Interrupt Disable Register HSMCI_IDR Write-only – 0x4C Interrupt Mask Register HSMCI_IMR Read-only 0x0 0x50 DMA Configuration Register HSMCI_DMA Read/Write 0x00 0x54 Configuration Register HSMCI_CFG Read/Write 0x00 0x58–0xE0 Reserved – – – 0xE4 Write Protection Mode Register HSMCI_WPMR Read/Write – 0xE8 Write Protection Status Register HSMCI_WPSR Read-only – 0xEC–0xFC Reserved – – – 0x100–0x1FC Reserved – – – 0x200 FIFO Memory Aperture 0 HSMCI_FIFO0 Read/Write 0x0 ... ... ... ... ... 0x5FC FIFO Memory Aperture 255 HSMCI_FIFO255 Read/Write 0x0 Note: 1. The response register can be read by N accesses at the same HSMCI_RSPR or at consecutive addresses (0x20 to 0x2C). N depends on the size of the response. SAM9M11 [DATASHEET] 803 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.1 HSMCI Control Register Name: HSMCI_CR Address: 0xFFF80000 (0), 0xFFFD0000 (1) Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 SWRST – – – PWSDIS PWSEN MCIDIS MCIEN • MCIEN: Multi-Media Interface Enable 0: No effect. 1: Enables the Multi-Media Interface if MCDIS is 0. • MCIDIS: Multi-Media Interface Disable 0: No effect. 1: Disables the Multi-Media Interface. • PWSEN: Power Save Mode Enable 0: No effect. 1: Enables the Power Saving Mode if PWSDIS is 0. Warning: Before enabling this mode, the user must set a value different from 0 in the PWSDIV field (Mode Register, HSMCI_MR). • PWSDIS: Power Save Mode Disable 0: No effect. 1: Disables the Power Saving Mode. • SWRST: Software Reset 0: No effect. 1: Resets the HSMCI. A software triggered hardware reset of the HSMCI interface is performed. 804 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.2 HSMCI Mode Register Name: HSMCI_MR Address: 0xFFF80004 (0), 0xFFFD0004 (1) Access: Read/Write 31 30 29 28 27 26 25 24 BLKLEN 23 22 21 20 19 18 17 16 BLKLEN 15 14 13 12 11 10 9 8 – PADV FBYTE WRPROOF RDPROOF PWSDIV 7 6 5 4 3 2 1 0 CLKDIV This register can only be written if the WPEN bit is cleared in “HSMCI Write Protect Mode Register” on page 829. • CLKDIV: Clock Divider High Speed MultiMedia Card Interface clock (MCCK or HSMCI_CK) is Master Clock (MCK) divided by (2*(CLKDIV+1)). • PWSDIV: Power Saving Divider High Speed MultiMedia Card Interface clock is divided by 2(PWSDIV) + 1 when entering Power Saving Mode. Warning: This value must be different from 0 before enabling the Power Save Mode in the HSMCI_CR (PWSEN bit). • RDPROOF Read Proof Enable Enabling Read Proof allows to stop the HSMCI Clock during read access if the internal FIFO is full. This will guarantee data integrity, not bandwidth. 0: Disables Read Proof. 1: Enables Read Proof. • WRPROOF Write Proof Enable Enabling Write Proof allows to stop the HSMCI Clock during write access if the internal FIFO is full. This will guarantee data integrity, not bandwidth. 0: Disables Write Proof. 1: Enables Write Proof. • FBYTE: Force Byte Transfer Enabling Force Byte Transfer allow byte transfers, so that transfer of blocks with a size different from modulo 4 can be supported. Warning: BLKLEN value depends on FBYTE. 0: Disables Force Byte Transfer. 1: Enables Force Byte Transfer. SAM9M11 [DATASHEET] 805 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• PADV: Padding Value 0: 0x00 value is used when padding data in write transfer. 1: 0xFF value is used when padding data in write transfer. PADV may be only in manual transfer. • BLKLEN: Data Block Length This field determines the size of the data block. This field is also accessible in the HSMCI Block Register (HSMCI_BLKR). Bits 16 and 17 must be set to 0 if FBYTE is disabled. Note: In SDIO Byte mode, BLKLEN field is not used. 806 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.3 HSMCI Data Timeout Register Name: HSMCI_DTOR Address: 0xFFF80008 (0), 0xFFFD0008 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – DTOMUL DTOCYC This register can only be written if the WPEN bit is cleared in “HSMCI Write Protect Mode Register” on page 829. • DTOCYC: Data Timeout Cycle Number These fields determine the maximum number of Master Clock cycles that the HSMCI waits between two data block trans- fers. It equals (DTOCYC x Multiplier). • DTOMUL: Data Timeout Multiplier Multiplier is defined by DTOMUL as shown in the following table: Value Name Description 0 1 DTOCYC 1 16 DTOCYC x 16 2 128 DTOCYC x 128 3 256 DTOCYC x 256 4 1024 DTOCYC x 1024 5 4096 DTOCYC x 4096 6 65536 DTOCYC x 65536 7 1048576 DTOCYC x 1048576 If the data time-out set by DTOCYC and DTOMUL has been exceeded, the Data Time-out Error flag (DTOE) in the HSMCI Status Register (HSMCI_SR) rises. SAM9M11 [DATASHEET] 807 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.4 HSMCI SDCard/SDIO Register Name: HSMCI_SDCR Address: 0xFFF8000C (0), 0xFFFD000C (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 SDCBUS – – – – SDCSEL This register can only be written if the WPEN bit is cleared in “HSMCI Write Protect Mode Register” on page 829. • SDCSEL: SDCard/SDIO Slot Value Name Description 0 SLOTA Slot A is selected. 1 SLOTB – 2 SLOTC – 3 SLOTD – • SDCBUS: SDCard/SDIO Bus Width Value Name Description 0 1 1 bit 1 – Reserved 2 4 4 bit 3 8 8 bit 808 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.5 HSMCI Argument Register Name: HSMCI_ARGR Address: 0xFFF80010 (0), 0xFFFD0010 (1) Access: Read/Write 31 30 29 28 27 26 25 24 ARG 23 22 21 20 19 18 17 16 ARG 15 14 13 12 11 10 9 8 ARG 7 6 5 4 3 2 1 0 ARG • ARG: Command Argument SAM9M11 [DATASHEET] 809 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.6 HSMCI Command Register Name: HSMCI_CMDR Address: 0xFFF80014 (0), 0xFFFD0014 (1) Access: Write-only 31 30 29 28 27 26 25 24 – – – – BOOT_ACK ATACS IOSPCMD 23 22 21 20 19 18 17 16 – – TRTYP TRDIR TRCMD 15 14 13 12 11 10 9 8 – – – MAXLAT OPDCMD SPCMD 7 6 5 4 3 2 1 0 RSPTYP CMDNB This register is write-protected while CMDRDY is 0 in HSMCI_SR. If an Interrupt command is sent, this register is only writable by an interrupt response (field SPCMD). This means that the current command execution cannot be interrupted or modified. • CMDNB: Command Number This is the command index. • RSPTYP: Response Type Value Name Description 0 NORESP No response. 1 48_BIT 48-bit response. 2 136_BIT 136-bit response. 3 R1B R1b response type • SPCMD: Special Command Value Name Description 0 STD Not a special CMD. Initialization CMD: 1 INIT 74 clock cycles for initialization sequence. Synchronized CMD: 2 SYNC Wait for the end of the current data block transfer before sending the pending command. CE-ATA Completion Signal disable Command. 3 CE_ATA The host cancels the ability for the device to return a command completion signal on the command line. Interrupt command: 4 IT_CMD Corresponds to the Interrupt Mode (CMD40). Interrupt response: 5 IT_RESP Corresponds to the Interrupt Mode (CMD40). Boot Operation Request. 6 BOR Start a boot operation mode, the host processor can read boot data from the MMC device directly. End Boot Operation. 7 EBO This command allows the host processor to terminate the boot operation mode. 810 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• OPDCMD: Open Drain Command 0 (PUSHPULL): Push pull command. 1 (OPENDRAIN): Open drain command. • MAXLAT: Max Latency for Command to Response 0 (5): 5-cycle max latency. 1 (64): 64-cycle max latency. • TRCMD: Transfer Command Value Name Description 0 NO_DATA No data transfer 1 START_DATA Start data transfer 2 STOP_DATA Stop data transfer 3 – Reserved • TRDIR: Transfer Direction 0 (WRITE): Write. 1 (READ): Read. • TRTYP: Transfer Type Value Name Description 0 SINGLE MMC/SDCard Single Block 1 MULTIPLE MMC/SDCard Multiple Block 2 STREAM MMC Stream 4 BYTE SDIO Byte 5 BLOCK SDIO Block • IOSPCMD: SDIO Special Command Value Name Description 0 STD Not an SDIO Special Command 1 SUSPEND SDIO Suspend Command 2 RESUME SDIO Resume Command • ATACS: ATA with Command Completion Signal 0 (NORMAL): Normal operation mode. 1 (COMPLETION): This bit indicates that a completion signal is expected within a programmed amount of time (HSMCI_CSTOR). • BOOT_ACK: Boot Operation Acknowledge The master can choose to receive the boot acknowledge from the slave when a Boot Request command is issued. When set to one this field indicates that a Boot acknowledge is expected within a programmable amount of time defined with DTOMUL and DTOCYC fields located in the HSMCI_DTOR. If the acknowledge pattern is not received then an acknowl- edge timeout error is raised. If the acknowledge pattern is corrupted then an acknowledge pattern error is set. SAM9M11 [DATASHEET] 811 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.7 HSMCI Block Register Name: HSMCI_BLKR Address: 0xFFF80018 (0), 0xFFFD0018 (1) Access: Read/Write 31 30 29 28 27 26 25 24 BLKLEN 23 22 21 20 19 18 17 16 BLKLEN 15 14 13 12 11 10 9 8 BCNT 7 6 5 4 3 2 1 0 BCNT • BCNT: MMC/SDIO Block Count - SDIO Byte Count This field determines the number of data byte(s) or block(s) to transfer. The transfer data type and the authorized values for BCNT field are determined by the TRTYP field in HSMCI_CMDR): Value Name Description MMC/SDCARD Multiple Block 0 MULTIPLE From 1 to 65635: Value 0 corresponds to an infinite block transfer. SDIO Byte 4 BYTE From 1 to 512 bytes: Value 0 corresponds to a 512-byte transfer. Values from 0x200 to 0xFFFF are forbidden. SDIO Block 5 BLOCK From 1 to 511 blocks: Value 0 corresponds to an infinite block transfer. Values from 0x200 to 0xFFFF are forbidden. Warning: In SDIO Byte and Block modes, writing to the 7 last bits of BCNT field is forbidden and may lead to unpredictable results. • BLKLEN: Data Block Length This field determines the size of the data block. This field is also accessible in the HSMCI Mode Register (HSMCI_MR). Bits 16 and 17 must be set to 0 if FBYTE is disabled. Note: In SDIO Byte mode, BLKLEN field is not used. 812 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.8 HSMCI Completion Signal Timeout Register Name: HSMCI_CSTOR Address: 0xFFF8001C (0), 0xFFFD001C (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – CSTOMUL CSTOCYC This register can only be written if the WPEN bit is cleared in “HSMCI Write Protect Mode Register” on page 829. • CSTOCYC: Completion Signal Timeout Cycle Number These fields determine the maximum number of Master Clock cycles that the HSMCI waits between two data block trans- fers. Its value is calculated by (CSTOCYC x Multiplier). • CSTOMUL: Completion Signal Timeout Multiplier These fields determine the maximum number of Master Clock cycles that the HSMCI waits between two data block trans- fers. Its value is calculated by (CSTOCYC x Multiplier). These fields determine the maximum number of Master Clock cycles that the HSMCI waits between the end of the data transfer and the assertion of the completion signal. The data transfer comprises data phase and the optional busy phase. If a non-DATA ATA command is issued, the HSMCI starts waiting immediately after the end of the response until the comple- tion signal. Multiplier is defined by CSTOMUL as shown in the following table: Value Name Description 0 1 CSTOCYC x 1 1 16 CSTOCYC x 16 2 128 CSTOCYC x 128 3 256 CSTOCYC x 256 4 1024 CSTOCYC x 1024 5 4096 CSTOCYC x 4096 6 65536 CSTOCYC x 65536 7 1048576 CSTOCYC x 1048576 If the data time-out set by CSTOCYC and CSTOMUL has been exceeded, the Completion Signal Time-out Error flag (CSTOE) in the HSMCI Status Register (HSMCI_SR) rises. SAM9M11 [DATASHEET] 813 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.9 HSMCI Response Register Name: HSMCI_RSPR Address: 0xFFF80020 (0), 0xFFFD0020 (1) Access: Read-only 31 30 29 28 27 26 25 24 RSP 23 22 21 20 19 18 17 16 RSP 15 14 13 12 11 10 9 8 RSP 7 6 5 4 3 2 1 0 RSP • RSP: Response Note: 1. The response register can be read by N accesses at the same HSMCI_RSPR or at consecutive addresses (0x20 to 0x2C). N depends on the size of the response. 814 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.10 HSMCI Receive Data Register Name: HSMCI_RDR Address: 0xFFF80030 (0), 0xFFFD0030 (1) Access: Read-only 31 30 29 28 27 26 25 24 DATA 23 22 21 20 19 18 17 16 DATA 15 14 13 12 11 10 9 8 DATA 7 6 5 4 3 2 1 0 DATA • DATA: Data to Read SAM9M11 [DATASHEET] 815 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.11 HSMCI Transmit Data Register Name: HSMCI_TDR Address: 0xFFF80034 (0), 0xFFFD0034 (1) Access: Write-only 31 30 29 28 27 26 25 24 DATA 23 22 21 20 19 18 17 16 DATA 15 14 13 12 11 10 9 8 DATA 7 6 5 4 3 2 1 0 DATA • DATA: Data to Write 816 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.12 HSMCI Status Register Name: HSMCI_SR Address: 0xFFF80040 (0), 0xFFFD0040 (1) Access: Read-only 31 30 29 28 27 26 25 24 UNRE OVRE ACKRCVE ACKRCV XFRDONE FIFOEMPTY DMADONE BLKOVRE 23 22 21 20 19 18 17 16 CSTOE DTOE DCRCE RTOE RENDE RCRCE RDIRE RINDE 15 14 13 12 11 10 9 8 – – CSRCV SDIOWAIT – – – SDIOIRQA 7 6 5 4 3 2 1 0 – – NOTBUSY DTIP BLKE TXRDY RXRDY CMDRDY • CMDRDY: Command Ready 0: A command is in progress. 1: The last command has been sent. Cleared when writing in the HSMCI_CMDR. • RXRDY: Receiver Ready 0: Data has not yet been received since the last read of HSMCI_RDR. 1: Data has been received since the last read of HSMCI_RDR. • TXRDY: Transmit Ready 0: The last data written in HSMCI_TDR has not yet been transferred in the Shift Register. 1: The last data written in HSMCI_TDR has been transferred in the Shift Register. • BLKE: Data Block Ended This flag must be used only for Write Operations. 0: A data block transfer is not yet finished. Cleared when reading the HSMCI_SR. 1: A data block transfer has ended, including the CRC16 Status transmission. the flag is set for each transmitted CRC Status. Refer to the MMC or SD Specification for more details concerning the CRC Status. • DTIP: Data Transfer in Progress 0: No data transfer in progress. 1: The current data transfer is still in progress, including CRC16 calculation. Cleared at the end of the CRC16 calculation. • NOTBUSY: HSMCI Not Busy This flag must be used only for Write Operations. A block write operation uses a simple busy signalling of the write operation duration on the data (DAT0) line: during a data transfer block, if the card does not have a free data receive buffer, the card indicates this condition by pulling down the data line (DAT0) to LOW. The card stops pulling down the data line as soon as at least one receive buffer for the defined data transfer block length becomes free. SAM9M11 [DATASHEET] 817 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The NOTBUSY flag allows to deal with these different states. 0: The HSMCI is not ready for new data transfer. Cleared at the end of the card response. 1: The HSMCI is ready for new data transfer. Set when the busy state on the data line has ended. This corresponds to a free internal data receive buffer of the card. Refer to the MMC or SD Specification for more details concerning the busy behavior. For all the read operations, the NOTBUSY flag is cleared at the end of the host command. For the Infinite Read Multiple Blocks, the NOTBUSY flag is set at the end of the STOP_TRANSMISSION host command (CMD12). For the Single Block Reads, the NOTBUSY flag is set at the end of the data read block. For the Multiple Block Reads with pre-defined block count, the NOTBUSY flag is set at the end of the last received data block. • SDIOIRQA: SDIO Interrupt for Slot A 0: No interrupt detected on SDIO Slot A. 1: An SDIO Interrupt on Slot A occurred. Cleared when reading the HSMCI_SR. • SDIOWAIT: SDIO Read Wait Operation Status 0: Normal Bus operation. 1: The data bus has entered IO wait state. • CSRCV: CE-ATA Completion Signal Received 0: No completion signal received since last status read operation. 1: The device has issued a command completion signal on the command line. Cleared by reading in the HSMCI_SR. • RINDE: Response Index Error 0: No error. 1: A mismatch is detected between the command index sent and the response index received. Cleared when writing in the HSMCI_CMDR. • RDIRE: Response Direction Error 0: No error. 1: The direction bit from card to host in the response has not been detected. • RCRCE: Response CRC Error 0: No error. 1: A CRC7 error has been detected in the response. Cleared when writing in the HSMCI_CMDR. • RENDE: Response End Bit Error 0: No error. 1: The end bit of the response has not been detected. Cleared when writing in the HSMCI_CMDR. • RTOE: Response Time-out Error 0: No error. 1: The response time-out set by MAXLAT in the HSMCI_CMDR has been exceeded. Cleared when writing in the HSMCI_CMDR. 818 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DCRCE: Data CRC Error 0: No error. 1: A CRC16 error has been detected in the last data block. Cleared by reading in the HSMCI_SR. • DTOE: Data Time-out Error 0: No error. 1: The data time-out set by DTOCYC and DTOMUL in HSMCI_DTOR has been exceeded. Cleared by reading in the HSMCI_SR. • CSTOE: Completion Signal Time-out Error 0: No error. 1: The completion signal time-out set by CSTOCYC and CSTOMUL in HSMCI_CSTOR has been exceeded. Cleared by reading in the HSMCI_SR. Cleared by reading in the HSMCI_SR. • BLKOVRE: DMA Block Overrun Error 0: No error. 1: A new block of data is received and the DMA controller has not started to move the current pending block, a block over- run is raised. Cleared by reading in the HSMCI_SR. • DMADONE: DMA Transfer done 0: DMA buffer transfer has not completed since the last read of HSMCI_SR. 1: DMA buffer transfer has completed. • FIFOEMPTY: FIFO empty flag 0: FIFO contains at least one byte. 1: FIFO is empty. • XFRDONE: Transfer Done flag 0: A transfer is in progress. 1: Command register is ready to operate and the data bus is in the idle state. • ACKRCV: Boot Operation Acknowledge Received 0: No Boot acknowledge received since the last read of the status register. 1: A Boot acknowledge signal has been received. Cleared by reading the HSMCI_SR. • ACKRCVE: Boot Operation Acknowledge Error 0: No error 1: Corrupted Boot Acknowledge signal received. • OVRE: Overrun 0: No error. 1: At least one 8-bit received data has been lost (not read). Cleared when sending a new data transfer command. When FERRCTRL in HSMCI_CFG is set to 1, OVRE becomes reset after read. SAM9M11 [DATASHEET] 819 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• UNRE: Underrun 0: No error. 1: At least one 8-bit data has been sent without valid information (not written). Cleared when sending a new data transfer command or when setting FERRCTRL in HSMCI_CFG to 1. When FERRCTRL in HSMCI_CFG is set to 1, UNRE becomes reset after read. 820 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.13 HSMCI Interrupt Enable Register Name: HSMCI_IER Address: 0xFFF80044 (0), 0xFFFD0044 (1) Access: Write-only 31 30 29 28 27 26 25 24 UNRE OVRE ACKRCVE ACKRCV XFRDONE FIFOEMPTY DMADONE BLKOVRE 23 22 21 20 19 18 17 16 CSTOE DTOE DCRCE RTOE RENDE RCRCE RDIRE RINDE 15 14 13 12 11 10 9 8 – – CSRCV SDIOWAIT – – – SDIOIRQA 7 6 5 4 3 2 1 0 – – NOTBUSY DTIP BLKE TXRDY RXRDY CMDRDY • CMDRDY: Command Ready Interrupt Enable • RXRDY: Receiver Ready Interrupt Enable • TXRDY: Transmit Ready Interrupt Enable • BLKE: Data Block Ended Interrupt Enable • DTIP: Data Transfer in Progress Interrupt Enable • NOTBUSY: Data Not Busy Interrupt Enable • SDIOIRQA: SDIO Interrupt for Slot A Interrupt Enable • SDIOWAIT: SDIO Read Wait Operation Status Interrupt Enable • CSRCV: Completion Signal Received Interrupt Enable • RINDE: Response Index Error Interrupt Enable • RDIRE: Response Direction Error Interrupt Enable • RCRCE: Response CRC Error Interrupt Enable • RENDE: Response End Bit Error Interrupt Enable • RTOE: Response Time-out Error Interrupt Enable • DCRCE: Data CRC Error Interrupt Enable • DTOE: Data Time-out Error Interrupt Enable • CSTOE: Completion Signal Timeout Error Interrupt Enable • BLKOVRE: DMA Block Overrun Error Interrupt Enable • DMADONE: DMA Transfer completed Interrupt Enable SAM9M11 [DATASHEET] 821 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• FIFOEMPTY: FIFO empty Interrupt enable • XFRDONE: Transfer Done Interrupt enable • ACKRCV: Boot Acknowledge Interrupt Enable • ACKRCVE: Boot Acknowledge Error Interrupt Enable • OVRE: Overrun Interrupt Enable • UNRE: Underrun Interrupt Enable 0: No effect. 1: Enables the corresponding interrupt. 822 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.14 HSMCI Interrupt Disable Register Name: HSMCI_IDR Address: 0xFFF80048 (0), 0xFFFD0048 (1) Access: Write-only 31 30 29 28 27 26 25 24 UNRE OVRE ACKRCVE ACKRCV XFRDONE FIFOEMPTY DMADONE BLKOVRE 23 22 21 20 19 18 17 16 CSTOE DTOE DCRCE RTOE RENDE RCRCE RDIRE RINDE 15 14 13 12 11 10 9 8 – – CSRCV SDIOWAIT – – – SDIOIRQA 7 6 5 4 3 2 1 0 – – NOTBUSY DTIP BLKE TXRDY RXRDY CMDRDY • CMDRDY: Command Ready Interrupt Disable • RXRDY: Receiver Ready Interrupt Disable • TXRDY: Transmit Ready Interrupt Disable • BLKE: Data Block Ended Interrupt Disable • DTIP: Data Transfer in Progress Interrupt Disable • NOTBUSY: Data Not Busy Interrupt Disable • SDIOIRQA: SDIO Interrupt for Slot A Interrupt Disable • SDIOWAIT: SDIO Read Wait Operation Status Interrupt Disable • CSRCV: Completion Signal received interrupt Disable • RINDE: Response Index Error Interrupt Disable • RDIRE: Response Direction Error Interrupt Disable • RCRCE: Response CRC Error Interrupt Disable • RENDE: Response End Bit Error Interrupt Disable • RTOE: Response Time-out Error Interrupt Disable • DCRCE: Data CRC Error Interrupt Disable • DTOE: Data Time-out Error Interrupt Disable • CSTOE: Completion Signal Time out Error Interrupt Disable • BLKOVRE: DMA Block Overrun Error Interrupt Disable • DMADONE: DMA Transfer completed Interrupt Disable SAM9M11 [DATASHEET] 823 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• FIFOEMPTY: FIFO empty Interrupt Disable • XFRDONE: Transfer Done Interrupt Disable • ACKRCV: Boot Acknowledge Interrupt Disable • ACKRCVE: Boot Acknowledge Error Interrupt Disable • OVRE: Overrun Interrupt Disable • UNRE: Underrun Interrupt Disable 0: No effect. 1: Disables the corresponding interrupt. 824 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.15 HSMCI Interrupt Mask Register Name: HSMCI_IMR Address: 0xFFF8004C (0), 0xFFFD004C (1) Access: Read-only 31 30 29 28 27 26 25 24 UNRE OVRE ACKRCVE ACKRCV XFRDONE FIFOEMPTY DMADONE BLKOVRE 23 22 21 20 19 18 17 16 CSTOE DTOE DCRCE RTOE RENDE RCRCE RDIRE RINDE 15 14 13 12 11 10 9 8 – – CSRCV SDIOWAIT – – – SDIOIRQA 7 6 5 4 3 2 1 0 – – NOTBUSY DTIP BLKE TXRDY RXRDY CMDRDY • CMDRDY: Command Ready Interrupt Mask • RXRDY: Receiver Ready Interrupt Mask • TXRDY: Transmit Ready Interrupt Mask • BLKE: Data Block Ended Interrupt Mask • DTIP: Data Transfer in Progress Interrupt Mask • NOTBUSY: Data Not Busy Interrupt Mask • SDIOIRQA: SDIO Interrupt for Slot A Interrupt Mask • SDIOWAIT: SDIO Read Wait Operation Status Interrupt Mask • CSRCV: Completion Signal Received Interrupt Mask • RINDE: Response Index Error Interrupt Mask • RDIRE: Response Direction Error Interrupt Mask • RCRCE: Response CRC Error Interrupt Mask • RENDE: Response End Bit Error Interrupt Mask • RTOE: Response Time-out Error Interrupt Mask • DCRCE: Data CRC Error Interrupt Mask • DTOE: Data Time-out Error Interrupt Mask • CSTOE: Completion Signal Time-out Error Interrupt Mask • BLKOVRE: DMA Block Overrun Error Interrupt Mask • DMADONE: DMA Transfer Completed Interrupt Mask SAM9M11 [DATASHEET] 825 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• FIFOEMPTY: FIFO Empty Interrupt Mask • XFRDONE: Transfer Done Interrupt Mask • ACKRCV: Boot Operation Acknowledge Received Interrupt Mask • ACKRCVE: Boot Operation Acknowledge Error Interrupt Mask • OVRE: Overrun Interrupt Mask • UNRE: Underrun Interrupt Mask 0: The corresponding interrupt is not enabled. 1: The corresponding interrupt is enabled. 826 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.16 HSMCI DMA Configuration Register Name: HSMCI_DMA Address: 0xFFF80050 (0), 0xFFFD0050 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – ROPT – – – DMAEN 7 6 5 4 3 2 1 0 – – CHKSIZE – – OFFSET This register can only be written if the WPEN bit is cleared in “HSMCI Write Protect Mode Register” on page 829. • OFFSET: DMA Write Buffer Offset This field indicates the number of discarded bytes when the DMA writes the first word of the transfer. • CHKSIZE: DMA Channel Read and Write Chunk Size The CHKSIZE field indicates the number of data available when the DMA chunk transfer request is asserted. Value Name Description 00 1 1 data available 01 4 4 data available 10 8 8 data available 11 16 16 data available • DMAEN: DMA Hardware Handshaking Enable 0: DMA interface is disabled. 1: DMA Interface is enabled. Note: To avoid unpredictable behavior, DMA hardware handshaking must be disabled when CPU transfers are performed. • ROPT: Read Optimization with padding 0: BLKLEN bytes are moved from the Memory Card to the system memory, two DMA descriptors are used when the trans- fer size is not a multiple of 4. 1: Ceiling(BLKLEN/4) * 4 bytes are moved from the Memory Card to the system memory, only one DMA descriptor is used. SAM9M11 [DATASHEET] 827 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.17 HSMCI Configuration Register Name: HSMCI_CFG Address: 0xFFF80054 (0), 0xFFFD0054 (1) Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – LSYNC – – – HSMODE 7 6 5 4 3 2 1 0 – – – FERRCTRL – – – FIFOMODE This register can only be written if the WPEN bit is cleared in “HSMCI Write Protect Mode Register” on page 829. • FIFOMODE: HSMCI Internal FIFO control mode 0: A write transfer starts when a sufficient amount of data is written into the FIFO. When the block length is greater than or equal to 3/4 of the HSMCI internal FIFO size, then the write transfer starts as soon as half the FIFO is filled. When the block length is greater than or equal to half the internal FIFO size, then the write trans- fer starts as soon as one quarter of the FIFO is filled. In other cases, the transfer starts as soon as the total amount of data is written in the internal FIFO. 1: A write transfer starts as soon as one data is written into the FIFO. • FERRCTRL: Flow Error flag reset control mode 0: When an underflow/overflow condition flag is set, a new Write/Read command is needed to reset the flag. 1: When an underflow/overflow condition flag is set, a read status resets the flag. • HSMODE: High Speed Mode 0: Default bus timing mode. 1: If set to one, the host controller outputs command line and data lines on the rising edge of the card clock. The Host driver shall check the high speed support in the card registers. • LSYNC: Synchronize on the last block 0: The pending command is sent at the end of the current data block. 1: The pending command is sent at the end of the block transfer when the transfer length is not infinite. (block count shall be different from zero) 828 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.18 HSMCI Write Protect Mode Register Name: HSMCI_WPMR Address: 0xFFF800E4 (0), 0xFFFD00E4 (1) Access: Read/Write 31 30 29 28 27 26 25 24 WP_KEY (0x4D => “M”) 23 22 21 20 19 18 17 16 WP_KEY (0x43 => C”) 15 14 13 12 11 10 9 8 WP_KEY (0x49 => “I”) 7 6 5 4 3 2 1 0 – – – – – – – WP_EN • WP_EN: Write Protection Enable 0: Disables the Write Protection if WP_KEY corresponds to 0x4D4349 (“MCI” in ASCII). 1: Enables the Write Protection if WP_KEY corresponds to 0x4D4349 (“MCI” in ASCII). • WP_KEY: Write Protection Key Password Should be written at value 0x4D4349 (ASCII code for “MCI”). Writing any other value in this field has no effect. Protects the registers: • “HSMCI Mode Register” on page 805 • “HSMCI Data Timeout Register” on page 807 • “HSMCI SDCard/SDIO Register” on page 808 • “HSMCI Completion Signal Timeout Register” on page 813 • “HSMCI DMA Configuration Register” on page 827 • “HSMCI Configuration Register” on page 828 SAM9M11 [DATASHEET] 829 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.19 HSMCI Write Protect Status Register Name: HSMCI_WPSR Address: 0xFFF800E8 (0), 0xFFFD00E8 (1) Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 WP_VSRC 15 14 13 12 11 10 9 8 WP_VSRC 7 6 5 4 3 2 1 0 – – – – WP_VS • WP_VS: Write Protection Violation Status Value Name Description 0 NONE No Write Protection Violation occurred since the last read of this register (WP_SR) 1 WRITE Write Protection detected unauthorized attempt to write a control register had occurred (since the last read.) 2 RESET Software reset had been performed while Write Protection was enabled (since the last read). Both Write Protection violation and software reset with Write Protection enabled have occurred since the last 3 BOTH read. • WP_VSRC: Write Protection Violation Source When WPVS is active, this field indicates the write-protected register (through address offset or code) in which a write access has been attempted. 830 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

36.14.20 HSMCI FIFOx Memory Aperture Name: HSMCI_FIFOx[x=0..255] Access: Read/Write 31 30 29 28 27 26 25 24 DATA 23 22 21 20 19 18 17 16 DATA 15 14 13 12 11 10 9 8 DATA 7 6 5 4 3 2 1 0 DATA • DATA: Data to Read or Data to Write SAM9M11 [DATASHEET] 831 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37. Ethernet MAC 10/100 (EMAC) 37.1 Description The EMAC module implements a 10/100 Ethernet MAC compatible with the IEEE 802.3 standard using an address checker, statistics and control registers, receive and transmit blocks, and a DMA interface. The address checker recognizes four specific 48-bit addresses and contains a 64-bit hash register for matching multicast and unicast addresses. It can recognize the broadcast address of all ones, copy all frames, and act on an external address match signal. The statistics register block contains registers for counting various types of event associated with transmit and receive operations. These registers, along with the status words stored in the receive buffer list, enable software to generate network management statistics compatible with IEEE 802.3. 37.2 Embedded Characteristics  Compatibility with IEEE Standard 802.3  10 and 100 Mbits per second data throughput capability  Full- and half-duplex operations  MII or RMII interface to the physical layer  Register Interface to address, data, status and control registers  DMA Interface, operating as a master on the Memory Controller  Interrupt generation to signal receive and transmit completion  128-byte transmit and 128-byte receive FIFOs  Automatic pad and CRC generation on transmitted frames  Address checking logic to recognize four 48-bit addresses  Supports promiscuous mode where all valid frames are copied to memory  Supports physical layer management through MDIO interface  Supports Wake-on-LAN. The receiver supports Wake-on-LAN by detecting the following events on incoming receive frames: ̶ Magic packet ̶ ARP request to the device IP address ̶ Specific address 1 filter match ̶ Multicast hash filter match 832 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.3 Block Diagram Figure 37-1. EMAC Block Diagram Address Checker APB Slave Register Interface Statistics Registers MDIO Control Registers DMA Interface RX FIFO TX FIFO Ethernet Receive MII/RMII AHB Master Ethernet Transmit SAM9M11 [DATASHEET] 833 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.4 Functional Description The MACB has several clock domains:  System bus clock (AHB and APB): DMA and register blocks  Transmit clock: transmit block  Receive clock: receive and address checker block The system bus clock must run at least as fast as the receive clock and transmit clock (25 MHz at 100 Mbps, and 2.5 MHz at 10 Mbps). Figure 37-1 illustrates the different blocks of the EMAC module. The control registers drive the MDIO interface, set up DMA activity, start frame transmission and select modes of operation such as full- or half-duplex. The receive block checks for valid preamble, FCS, alignment and length, and presents received frames to the address checking block and DMA interface. The transmit block takes data from the DMA interface, adds preamble and, if necessary, pad and FCS, and transmits data according to the CSMA/CD (carrier sense multiple access with collision detect) protocol. The start of transmission is deferred if CRS (carrier sense) is active. If COL (collision) becomes active during transmission, a jam sequence is asserted and the transmission is retried after a random back off. CRS and COL have no effect in full duplex mode. The DMA block connects to external memory through its AHB bus interface. It contains receive and transmit FIFOs for buffering frame data. It loads the transmit FIFO and empties the receive FIFO using AHB bus master operations. Receive data is not sent to memory until the address checking logic has determined that the frame should be copied. Receive or transmit frames are stored in one or more buffers. Receive buffers have a fixed length of 128 bytes. Transmit buffers range in length between 0 and 2047 bytes, and up to 128 buffers are permitted per frame. The DMA block manages the transmit and receive framebuffer queues. These queues can hold multiple frames. 37.4.1 Clock Synchronization module in the EMAC requires that the bus clock (hclk) runs at the speed of the macb_tx/rx_clk at least, which is 25 MHz at 100 Mbps, and 2.5 MHz at 10 Mbps. 37.4.2 Memory Interface Frame data is transferred to and from the EMAC through the DMA interface. All transfers are 32-bit words and may be single accesses or bursts of 2, 3 or 4 words. Burst accesses do not cross sixteen-byte boundaries. Bursts of 4 words are the default data transfer; single accesses or bursts of less than four words may be used to transfer data at the beginning or the end of a buffer. The DMA controller performs six types of operation on the bus. In order of priority, these are: 1. Receive buffer manager write 2. Receive buffer manager read 3. Transmit data DMA read 4. Receive data DMA write 5. Transmit buffer manager read 6. Transmit buffer manager write 37.4.2.1 FIFO The FIFO depths are 128 bytes for receive and 128 bytes for transmit and are a function of the system clock speed, memory latency and network speed. 834 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Data is typically transferred into and out of the FIFOs in bursts of four words. For receive, a bus request is asserted when the FIFO contains four words and has space for 28 more. For transmit, a bus request is generated when there is space for four words, or when there is space for 27 words if the next transfer is to be only one or two words. Thus the bus latency must be less than the time it takes to load the FIFO and transmit or receive three words (112 bytes) of data. At 100 Mbit/s, it takes 8960 ns to transmit or receive 112 bytes of data. In addition, six master clock cycles should be allowed for data to be loaded from the bus and to propagate through the FIFOs. For a 133 MHz master clock this takes 45 ns, making the bus latency requirement 8915ns. 37.4.2.2 Receive Buffers Received frames, including CRC/FCS optionally, are written to receive buffers stored in memory. Each receive buffer is 128 bytes long. The start location for each receive buffer is stored in memory in a list of receive buffer descriptors at a location pointed to by the receive buffer queue pointer register. The receive buffer start location is a word address. For the first buffer of a frame, the start location can be offset by up to three bytes depending on the value written to bits 14 and 15 of the network configuration register. If the start location of the buffer is offset the available length of the first buffer of a frame is reduced by the corresponding number of bytes. Each list entry consists of two words, the first being the address of the receive buffer and the second being the receive status. If the length of a receive frame exceeds the buffer length, the status word for the used buffer is written with zeroes except for the “start of frame” bit and the offset bits, if appropriate. Bit zero of the address field is written to one to show the buffer has been used. The receive buffer manager then reads the location of the next receive buffer and fills that with receive frame data. The final buffer descriptor status word contains the complete frame status. Refer to Table 37-1 for details of the receive buffer descriptor list. Table 37-1. Receive Buffer Descriptor Entry Bit Function Word 0 31:2 Address of beginning of buffer 1 Wrap - marks last descriptor in receive buffer descriptor list. Ownership - needs to be zero for the EMAC to write data to the receive buffer. The EMAC sets this to one once it has 0 successfully written a frame to memory. Software has to clear this bit before the buffer can be used again. Word 1 31 Global all ones broadcast address detected 30 Multicast hash match 29 Unicast hash match 28 External address match 27 Reserved for future use 26 Specific address register 1 match 25 Specific address register 2 match 24 Specific address register 3 match 23 Specific address register 4 match 22 Type ID match 21 VLAN tag detected (i.e., type id of 0x8100) 20 Priority tag detected (i.e., type id of 0x8100 and null VLAN identifier) SAM9M11 [DATASHEET] 835 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 37-1. Receive Buffer Descriptor Entry (Continued) Bit Function 19:17 VLAN priority (only valid if bit 21 is set) 16 Concatenation format indicator (CFI) bit (only valid if bit 21 is set) End of frame - when set the buffer contains the end of a frame. If end of frame is not set, then the only other valid status are 15 bits 12, 13 and 14. Start of frame - when set the buffer contains the start of a frame. If both bits 15 and 14 are set, then the buffer contains a 14 whole frame. Receive buffer offset - indicates the number of bytes by which the data in the first buffer is offset from the word address. Updated with the current values of the network configuration register. If jumbo frame mode is enabled through bit 3 of the 13:12 network configuration register, then bits 13:12 of the receive buffer descriptor entry are used to indicate bits 13:12 of the frame length. 11:0 Length of frame including FCS (if selected). Bits 13:12 are also used if jumbo frame mode is selected. To receive frames, the buffer descriptors must be initialized by writing an appropriate address to bits 31 to 2 in the first word of each list entry. Bit zero must be written with zero. Bit one is the wrap bit and indicates the last entry in the list. The start location of the receive buffer descriptor list must be written to the receive buffer queue pointer register before setting the receive enable bit in the network control register to enable receive. As soon as the receive block starts writing received frame data to the receive FIFO, the receive buffer manager reads the first receive buffer location pointed to by the receive buffer queue pointer register. If the filter block then indicates that the frame should be copied to memory, the receive data DMA operation starts writing data into the receive buffer. If an error occurs, the buffer is recovered. If the current buffer pointer has its wrap bit set or is the 1024th descriptor, the next receive buffer location is read from the beginning of the receive descriptor list. Otherwise, the next receive buffer location is read from the next word in memory. There is an 11-bit counter to count out the 2048 word locations of a maximum length, receive buffer descriptor list. This is added with the value originally written to the receive buffer queue pointer register to produce a pointer into the list. A read of the receive buffer queue pointer register returns the pointer value, which is the queue entry currently being accessed. The counter is reset after receive status is written to a descriptor that has its wrap bit set or rolls over to zero after 1024 descriptors have been accessed. The value written to the receive buffer pointer register may be any word-aligned address, provided that there are at least 2048 word locations available between the pointer and the top of the memory. Section 3.6 of the AMBA 2.0 specification states that bursts should not cross 1K boundaries. As receive buffer manager writes are bursts of two words, to ensure that this does not occur, it is best to write the pointer register with the least three significant bits set to zero. As receive buffers are used, the receive buffer manager sets bit zero of the first word of the descriptor to indicate used. If a receive error is detected the receive buffer currently being written is recovered. Previous buffers are not recovered. Software should search through the used bits in the buffer descriptors to find out how many frames have been received. It should be checking the start-of-frame and end-of- frame bits, and not rely on the value returned by the receive buffer queue pointer register which changes continuously as more buffers are used. For CRC errored frames, excessive length frames or length field mismatched frames, all of which are counted in the statistics registers, it is possible that a frame fragment might be stored in a sequence of receive buffers. Software can detect this by looking for start of frame bit set in a buffer following a buffer with no end of frame bit set. For a properly working Ethernet system, there should be no excessively long frames or frames greater than 128 bytes with CRC/FCS errors. Collision fragments are less than 128 bytes long. Therefore, it is a rare occurrence to find a frame fragment in a receive buffer. 836 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

If bit zero is set when the receive buffer manager reads the location of the receive buffer, then the buffer has already been used and cannot be used again until software has processed the frame and cleared bit zero. In this case, the DMA block sets the buffer not available bit in the receive status register and triggers an interrupt. If bit zero is set when the receive buffer manager reads the location of the receive buffer and a frame is being received, the frame is discarded and the receive resource error statistics register is incremented. A receive overrun condition occurs when bus was not granted in time or because HRESP was not OK (bus error). In a receive overrun condition, the receive overrun interrupt is asserted and the buffer currently being written is recovered. The next frame received with an address that is recognized reuses the buffer. If bit 17 of the network configuration register is set, the FCS of received frames shall not be copied to memory. The frame length indicated in the receive status field shall be reduced by four bytes in this case. 37.4.2.3 Transmit Buffer Frames to be transmitted are stored in one or more transmit buffers. Transmit buffers can be between 0 and 2047 bytes long, so it is possible to transmit frames longer than the maximum length specified in IEEE Standard 802.3. Zero length buffers are allowed. The maximum number of buffers permitted for each transmit frame is 128. The start location for each transmit buffer is stored in memory in a list of transmit buffer descriptors at a location pointed to by the transmit buffer queue pointer register. Each list entry consists of two words, the first being the byte address of the transmit buffer and the second containing the transmit control and status. Frames can be transmitted with or without automatic CRC generation. If CRC is automatically generated, pad is also automatically generated to take frames to a minimum length of 64 bytes. Table 37-2 on page 838 defines an entry in the transmit buffer descriptor list. To transmit frames, the buffer descriptors must be initialized by writing an appropriate byte address to bits 31 to 0 in the first word of each list entry. The second transmit buffer descriptor is initialized with control information that indicates the length of the buffer, whether or not it is to be transmitted with CRC and whether the buffer is the last buffer in the frame. After transmission, the control bits are written back to the second word of the first buffer along with the “used” bit and other status information. Bit 31 is the “used” bit which must be zero when the control word is read if transmission is to happen. It is written to one when a frame has been transmitted. Bits 27, 28 and 29 indicate various transmit error conditions. Bit 30 is the “wrap” bit which can be set for any buffer within a frame. If no wrap bit is encountered after 1024 descriptors, the queue pointer rolls over to the start in a similar fashion to the receive queue. The transmit buffer queue pointer register must not be written while transmit is active. If a new value is written to the transmit buffer queue pointer register, the queue pointer resets itself to point to the beginning of the new queue. If transmit is disabled by writing to bit 3 of the network control, the transmit buffer queue pointer register resets to point to the beginning of the transmit queue. Note that disabling receive does not have the same effect on the receive queue pointer. Once the transmit queue is initialized, transmit is activated by writing to bit 9, the Transmit Start bit of the network control register. Transmit is halted when a buffer descriptor with its used bit set is read, or if a transmit error occurs, or by writing to the transmit halt bit of the network control register. (Transmission is suspended if a pause frame is received while the pause enable bit is set in the network configuration register.) Rewriting the start bit while transmission is active is allowed. Transmission control is implemented with a Tx_go variable which is readable in the transmit status register at bit location 3. The Tx_go variable is reset when: ̶ transmit is disabled ̶ a buffer descriptor with its ownership bit set is read ̶ a new value is written to the transmit buffer queue pointer register ̶ bit 10, tx_halt, of the network control register is written ̶ there is a transmit error such as too many retries or a transmit underrun. SAM9M11 [DATASHEET] 837 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

To set tx_go, write to bit 9, tx_start, of the network control register. Transmit halt does not take effect until any ongoing transmit finishes. If a collision occurs during transmission of a multi-buffer frame, transmission automatically restarts from the first buffer of the frame. If a “used” bit is read midway through transmission of a multi-buffer frame, this is treated as a transmit error. Transmission stops, tx_er is asserted and the FCS is bad. If transmission stops due to a transmit error, the transmit queue pointer resets to point to the beginning of the transmit queue. Software needs to re-initialize the transmit queue after a transmit error. If transmission stops due to a “used” bit being read at the start of the frame, the transmission queue pointer is not reset and transmit starts from the same transmit buffer descriptor when the transmit start bit is written. Table 37-2. Transmit Buffer Descriptor Entry Bit Function Word 0 31:0 Byte Address of buffer Word 1 Used. Needs to be zero for the EMAC to read data from the transmit buffer. The EMAC sets this to one for the first buffer of a frame once it has been successfully transmitted. 31 Software has to clear this bit before the buffer can be used again. Note: This bit is only set for the first buffer in a frame unlike receive where all buffers have the Used bit set once used. 30 Wrap. Marks last descriptor in transmit buffer descriptor list. 29 Retry limit exceeded, transmit error detected Transmit underrun, occurs either when hresp is not OK (bus error) or the transmit data could not be fetched in time or when 28 buffers are exhausted in mid frame. 27 Buffers exhausted in mid frame 26:17 Reserved 16 No CRC. When set, no CRC is appended to the current frame. This bit only needs to be set for the last buffer of a frame. 15 Last buffer. When set, this bit indicates the last buffer in the current frame has been reached. 14:11 Reserved 10:0 Length of buffer 37.4.3 Transmit Block This block transmits frames in accordance with the Ethernet IEEE 802.3 CSMA/CD protocol. Frame assembly starts by adding preamble and the start frame delimiter. Data is taken from the transmit FIFO a word at a time. Data is transmitted least significant nibble first. If necessary, padding is added to increase the frame length to 60 bytes. CRC is calculated as a 32-bit polynomial. This is inverted and appended to the end of the frame, taking the frame length to a minimum of 64 bytes. If the No CRC bit is set in the second word of the last buffer descriptor of a transmit frame, neither pad nor CRC are appended. In full-duplex mode, frames are transmitted immediately. Back-to-back frames are transmitted at least 96 bit times apart to guarantee the interframe gap. In half-duplex mode, the transmitter checks carrier sense. If asserted, it waits for it to de-assert and then starts transmission after the interframe gap of 96 bit times. If the collision signal is asserted during transmission, the transmitter transmits a jam sequence of 32 bits taken from the data register and then retry transmission after the back off time has elapsed. The back-off time is based on an XOR of the 10 least significant bits of the data coming from the transmit FIFO and a 10-bit pseudo random number generator. The number of bits used depends on the number of collisions seen. 838 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

After the first collision, 1 bit is used, after the second 2, and so on up to 10. Above 10, all 10 bits are used. An error is indicated and no further attempts are made if 16 attempts cause collisions. If transmit DMA underruns, bad CRC is automatically appended using the same mechanism as jam insertion and the tx_er signal is asserted. For a properly configured system, this should never happen. If the back pressure bit is set in the network control register in half duplex mode, the transmit block transmits 64 bits of data, which can consist of 16 nibbles of 1011 or in bit-rate mode 64 1s, whenever it sees an incoming frame to force a collision. This provides a way of implementing flow control in half-duplex mode. 37.4.4 Pause Frame Support The start of an 802.3 pause frame is as follows: Table 37-3. Start of an 802.3 Pause Frame Destination Address Source Address Type (Mac Control Frame) Pause Opcode Pause Time 0x0180C2000001 6 bytes 0x8808 0x0001 2 bytes The network configuration register contains a receive pause enable bit (13). If a valid pause frame is received, the pause time register is updated with the frame’s pause time, regardless of its current contents and regardless of the state of the configuration register bit 13. An interrupt (12) is triggered when a pause frame is received, assuming it is enabled in the interrupt mask register. If bit 13 is set in the network configuration register and the value of the pause time register is non-zero, no new frame is transmitted until the pause time register has decremented to zero. The loading of a new pause time, and hence the pausing of transmission, only occurs when the EMAC is configured for full-duplex operation. If the EMAC is configured for half-duplex, there is no transmission pause, but the pause frame received interrupt is still triggered. A valid pause frame is defined as having a destination address that matches either the address stored in specific address register 1 or matches 0x0180C2000001 and has the MAC control frame type ID of 0x8808 and the pause opcode of 0x0001. Pause frames that have FCS or other errors are treated as invalid and are discarded. Valid pause frames received increment the Pause Frame Received statistic register. The pause time register decrements every 512 bit times (i.e., 128 rx_clks in nibble mode) once transmission has stopped. For test purposes, the register decrements every rx_clk cycle once transmission has stopped if bit 12 (retry test) is set in the network configuration register. If the pause enable bit (13) is not set in the network configuration register, then the decrementing occurs regardless of whether transmission has stopped or not. An interrupt (13) is asserted whenever the pause time register decrements to zero (assuming it is enabled in the interrupt mask register). 37.4.5 Receive Block The receive block checks for valid preamble, FCS, alignment and length, presents received frames to the DMA block and stores the frames destination address for use by the address checking block. If, during frame reception, the frame is found to be too long or rx_er is asserted, a bad frame indication is sent to the DMA block. The DMA block then ceases sending data to memory. At the end of frame reception, the receive block indicates to the DMA block whether the frame is good or bad. The DMA block recovers the current receive buffer if the frame was bad. The receive block signals the register block to increment the alignment error, the CRC (FCS) error, the short frame, long frame, jabber error, the receive symbol error statistics and the length field mismatch statistics. The enable bit for jumbo frames in the network configuration register allows the EMAC to receive jumbo frames of up to 10240 bytes in size. This operation does not form part of the IEEE802.3 specification and is disabled by default. When jumbo frames are enabled, frames received with a frame size greater than 10240 bytes are discarded. SAM9M11 [DATASHEET] 839 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.4.6 Address Checking Block The address checking (or filter) block indicates to the DMA block which receive frames should be copied to memory. Whether a frame is copied depends on what is enabled in the network configuration register, the state of the external match pin, the contents of the specific address and hash registers and the frame’s destination address. In this implementation of the EMAC, the frame’s source address is not checked. Provided that bit 18 of the Network Configuration register is not set, a frame is not copied to memory if the EMAC is transmitting in half duplex mode at the time a destination address is received. If bit 18 of the Network Configuration register is set, frames can be received while transmitting in half-duplex mode. Ethernet frames are transmitted a byte at a time, least significant bit first. The first six bytes (48 bits) of an Ethernet frame make up the destination address. The first bit of the destination address, the LSB of the first byte of the frame, is the group/individual bit: this is One for multicast addresses and Zero for unicast. The All Ones address is the broadcast address, and a special case of multicast. The EMAC supports recognition of four specific addresses. Each specific address requires two registers, specific address register bottom and specific address register top. Specific address register bottom stores the first four bytes of the destination address and specific address register top contains the last two bytes. The addresses stored can be specific, group, local or universal. The destination address of received frames is compared against the data stored in the specific address registers once they have been activated. The addresses are deactivated at reset or when their corresponding specific address register bottom is written. They are activated when specific address register top is written. If a receive frame address matches an active address, the frame is copied to memory. The following example illustrates the use of the address match registers for a MAC address of 21:43:65:87:A9:CB. Preamble 55 SFD D5 DA (Octet0 - LSB) 21 DA(Octet 1) 43 DA(Octet 2) 65 DA(Octet 3) 87 DA(Octet 4) A9 DA (Octet5 - MSB) CB SA (LSB) 00 SA 00 SA 00 SA 00 SA 00 SA (MSB) 43 SA (LSB) 21 The sequence above shows the beginning of an Ethernet frame. Byte order of transmission is from top to bottom as shown. For a successful match to specific address 1, the following address matching registers must be set up:  Base address + 0x98 0x87654321 (Bottom)  Base address + 0x9C 0x0000CBA9 (Top) And for a successful match to the Type ID register, the following should be set up:  Base address + 0xB8 0x00004321 840 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.4.7 Broadcast Address The broadcast address of 0xFFFFFFFFFFFF is recognized if the ‘no broadcast’ bit in the network configuration register is zero. 37.4.8 Hash Addressing The hash address register is 64 bits long and takes up two locations in the memory map. The least significant bits are stored in hash register bottom and the most significant bits in hash register top. The unicast hash enable and the multicast hash enable bits in the network configuration register enable the reception of hash matched frames. The destination address is reduced to a 6-bit index into the 64-bit hash register using the following hash function. The hash function is an exclusive or of every sixth bit of the destination address. hash_index[5] = da[5] ^ da[11] ^ da[17] ^ da[23] ^ da[29] ^ da[35] ^ da[41] ^ da[47] hash_index[4] = da[4] ^ da[10] ^ da[16] ^ da[22] ^ da[28] ^ da[34] ^ da[40] ^ da[46] hash_index[3] = da[3] ^ da[09] ^ da[15] ^ da[21] ^ da[27] ^ da[33] ^ da[39] ^ da[45] hash_index[2] = da[2] ^ da[08] ^ da[14] ^ da[20] ^ da[26] ^ da[32] ^ da[38] ^ da[44] hash_index[1] = da[1] ^ da[07] ^ da[13] ^ da[19] ^ da[25] ^ da[31] ^ da[37] ^ da[43] hash_index[0] = da[0] ^ da[06] ^ da[12] ^ da[18] ^ da[24] ^ da[30] ^ da[36] ^ da[42] da[0] represents the least significant bit of the first byte received, that is, the multicast/unicast indicator, and da[47] represents the most significant bit of the last byte received. If the hash index points to a bit that is set in the hash register, then the frame is matched according to whether the frame is multicast or unicast. A multicast match is signalled if the multicast hash enable bit is set. da[0] is 1 and the hash index points to a bit set in the hash register. A unicast match is signalled if the unicast hash enable bit is set. da[0] is 0 and the hash index points to a bit set in the hash register. To receive all multicast frames, the hash register should be set with all ones and the multicast hash enable bit should be set in the network configuration register. 37.4.9 Copy All Frames (or Promiscuous Mode) If the copy all frames bit is set in the network configuration register, then all non-errored frames are copied to memory. For example, frames that are too long, too short, or have FCS errors or rx_er asserted during reception are discarded and all others are received. Frames with FCS errors are copied to memory if bit 19 in the network configuration register is set. 37.4.10Type ID Checking The contents of the type_id register are compared against the length/type ID of received frames (i.e., bytes 13 and 14). Bit 22 in the receive buffer descriptor status is set if there is a match. The reset state of this register is zero which is unlikely to match the length/type ID of any valid Ethernet frame. Note: A type ID match does not affect whether a frame is copied to memory. SAM9M11 [DATASHEET] 841 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.4.11 VLAN Support An Ethernet encoded 802.1Q VLAN tag looks like this: Table 37-4. 802.1Q VLAN Tag TPID (Tag Protocol Identifier) 16 bits TCI (Tag Control Information) 16 bits 0x8100 First 3 bits priority, then CFI bit, last 12 bits VID The VLAN tag is inserted at the 13th byte of the frame, adding an extra four bytes to the frame. If the VID (VLAN identifier) is null (0x000), this indicates a priority-tagged frame. The MAC can support frame lengths up to 1536 bytes, 18 bytes more than the original Ethernet maximum frame length of 1518 bytes. This is achieved by setting bit 8 in the network configuration register. The following bits in the receive buffer descriptor status word give information about VLAN tagged frames:  Bit 21 set if receive frame is VLAN tagged (i.e., type id of 0x8100)  Bit 20 set if receive frame is priority tagged (i.e., type id of 0x8100 and null VID). (If bit 20 is set, bit 21 is set also.)  Bit 19, 18 and 17 set to priority if bit 21 is set  Bit 16 set to CFI if bit 21 is set 37.4.12Wake-on-LAN Support The receive block supports Wake-on-LAN by detecting the following events on incoming receive frames:  Magic packet  ARP request to the device IP address  Specific address 1 filter match  Multicast hash filter match If one of these events occurs Wake-on-LAN detection is indicated by asserting the wol output pin for 64 rx_clk cycles. These events can be individually enabled through bits[19:16] of the Wake-on-LAN register. Also, for Wake- on-LAN detection to occur, receive enable must be set in the network control register, however a receive buffer does not have to be available. wol assertion due to ARP request, specific address 1 or multicast filter events occurs even if the frame is errored. For magic packet events, the frame must be correctly formed and error free. A magic packet event is detected if all of the following are true:  magic packet events are enabled through bit 16 of the Wake-on-LAN register  the frame’s destination address matches specific address 1  the frame is correctly formed with no errors  the frame contains at least 6 bytes of 0xFF for synchronization  there are 16 repetitions of the contents of specific address 1 register immediately following the synchronization An ARP request event is detected if all of the following are true:  ARP request events are enabled through bit 17 of the Wake-on-LAN register  broadcasts are allowed by bit 5 in the network configuration register  the frame has a broadcast destination address (bytes 1 to 6)  the frame has a type ID field of 0x0806 (bytes 13 and 14)  the frame has an ARP operation field of 0x0001 (bytes 21 and 22)  the least significant 16 bits of the frame’s ARP target protocol address (bytes 41 and 42) match the value programmed in bits[15:0] of the Wake-on-LAN register 842 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The decoding of the ARP fields adjusts automatically if a VLAN tag is detected within the frame. The reserved value of 0x0000 for the Wake-on-LAN target address value does not cause an ARP request event, even if matched by the frame. A specific address 1 filter match event occurs if all of the following are true:  specific address 1 events are enabled through bit 18 of the Wake-on-LAN register  the frame’s destination address matches the value programmed in the specific address 1 registers A multicast filter match event occurs if all of the following are true:  multicast hash events are enabled through bit 19 of the Wake-on-LAN register  multicast hash filtering is enabled through bit 6 of the network configuration register  the frame’s destination address matches against the multicast hash filter  the frame’s destination address is not a broadcast 37.4.13PHY Maintenance The register EMAC_MAN enables the EMAC to communicate with a PHY by means of the MDIO interface. It is used during auto-negotiation to ensure that the EMAC and the PHY are configured for the same speed and duplex configuration. The PHY maintenance register is implemented as a shift register. Writing to the register starts a shift operation which is signalled as complete when bit two is set in the network status register (about 2000 MCK cycles later when bit ten is set to zero, and bit eleven is set to one in the network configuration register). An interrupt is generated as this bit is set. During this time, the MSB of the register is output on the MDIO pin and the LSB updated from the MDIO pin with each MDC cycle. This causes transmission of a PHY management frame on MDIO. Reading during the shift operation returns the current contents of the shift register. At the end of management operation, the bits have shifted back to their original locations. For a read operation, the data bits are updated with data read from the PHY. It is important to write the correct values to the register to ensure a valid PHY management frame is produced. The MDIO interface can read IEEE 802.3 clause 45 PHYs as well as clause 22 PHYs. To read clause 45 PHYs, bits[31:28] should be written as 0x0011. For a description of MDC generation, see the network configuration register in the “Network Control Register” on page 849. 37.4.14Media Independent Interface The Ethernet MAC is capable of interfacing to both RMII and MII Interfaces. The RMII bit in the EMAC_USRIO register controls the interface that is selected. When this bit is set, the RMII interface is selected, else the MII interface is selected. The MII and RMII interface are capable of both 10Mb/s and 100Mb/s data rates as described in the IEEE 802.3u standard. The signals used by the MII and RMII interfaces are described in Table 37-5 on page 844. SAM9M11 [DATASHEET] 843 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 37-5. Pin Configuration Pin Name MII RMII ETXCK_EREFCK ETXCK: Transmit Clock EREFCK: Reference Clock ECRS ECRS: Carrier Sense ECOL ECOL: Collision Detect ERXDV ERXDV: Data Valid ECRSDV: Carrier Sense/Data Valid ERX0–ERX3 ERX0–ERX3: 4-bit Receive Data ERX0–ERX1: 2-bit Receive Data ERXER ERXER: Receive Error ERXER: Receive Error ERXCK ERXCK: Receive Clock ETXEN ETXEN: Transmit Enable ETXEN: Transmit Enable ETX0–ETX3 ETX0–ETX3: 4-bit Transmit Data ETX0–ETX1: 2-bit Transmit Data ETXER ETXER: Transmit Error The intent of the RMII is to provide a reduced pin count alternative to the IEEE 802.3u MII. It uses two bits for transmit (ETX0 and ETX1) and two bits for receive (ERX0 and ERX1). There is a Transmit Enable (ETXEN), a Receive Error (ERXER), a Carrier Sense (ECRS_DV), and a 50 MHz Reference Clock (ETXCK_EREFCK) for 100Mb/s data rate. 37.4.14.1 RMII Transmit and Receive Operation The same signals are used internally for both the RMII and the MII operations. The RMII maps these signals in a more pin-efficient manner. The transmit and receive bits are converted from a 4-bit parallel format to a 2-bit parallel scheme that is clocked at twice the rate. The carrier sense and data valid signals are combined into the ECRSDV signal. This signal contains information on carrier sense, FIFO status, and validity of the data. Transmit error bit (ETXER) and collision detect (ECOL) are not used in RMII mode. 37.5 Programming Interface 37.5.1 Initialization 37.5.1.1 Configuration Initialization of the EMAC configuration (e.g., loop-back mode, frequency ratios) must be done while the transmit and receive circuits are disabled. See the description of the network control register and network configuration register earlier in this document. To change loop-back mode, the following sequence of operations must be followed: 1. Allocate a number (n) of buffers of 128 bytes in system memory. 2. Write to network control register to change loop-back mode. 3. Write to network control register to re-enable transmit or receive circuits. Note: These writes to network control register cannot be combined in any way. 37.5.1.2 Receive Buffer List Receive data is written to areas of data (i.e., buffers) in system memory. These buffers are listed in another data structure that also resides in main memory. This data structure (receive buffer queue) is a sequence of descriptor entries as defined in “Receive Buffer Descriptor Entry” on page 835. It points to this data structure. 844 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 37-2. Receive Buffer List Receive Buffer 0 Receive Buffer Queue Pointer (MAC Register) Receive Buffer 1 Receive Buffer N Receive Buffer Descriptor List (In memory) (In memory) To create the list of buffers: 1. Allocate a number (n) of buffers of 128 bytes in system memory. 2. Allocate an area 2n words for the receive buffer descriptor entry in system memory and create n entries in this list. Mark all entries in this list as owned by EMAC, i.e., bit 0 of word 0 set to 0. 3. If less than 1024 buffers are defined, the last descriptor must be marked with the wrap bit (bit 1 in word 0 set to 1). 4. Write address of receive buffer descriptor entry to EMAC register receive_buffer queue pointer. 5. The receive circuits can then be enabled by writing to the address recognition registers and then to the network control register. 37.5.1.3 Transmit Buffer List Transmit data is read from areas of data (the buffers) in system memory These buffers are listed in another data structure that also resides in main memory. This data structure (Transmit Buffer Queue) is a sequence of descriptor entries (as defined in Table 37-2 on page 838) that points to this data structure. To create this list of buffers: 1. Allocate a number (n) of buffers of 128 bytes in system memory. 2. Allocate an area 2n words for the transmit buffer descriptor entry in system memory and create N entries in this list. Mark all entries in this list as owned by EMAC, i.e., bit 31 of word 1 set to 0. 3. If fewer than 1024 buffers are defined, the last descriptor must be marked with the wrap bit — bit 30 in word 1 set to 1. 4. Write address of transmit buffer descriptor entry to EMAC register transmit_buffer queue pointer. 5. The transmit circuits can then be enabled by writing to the network control register. 37.5.1.4 Address Matching The EMAC register-pair hash address and the four specific address register-pairs must be written with the required values. Each register-pair comprises a bottom register and top register, with the bottom register being written first. The address matching is disabled for a particular register-pair after the bottom-register has been written and re- enabled when the top register is written. See “Address Checking Block” on page 840. for details of address matching. Each register-pair may be written at any time, regardless of whether the receive circuits are enabled or disabled. SAM9M11 [DATASHEET] 845 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.5.1.5 Interrupts There are 15 interrupt conditions that are detected within the EMAC. These are ORed to make a single interrupt. Depending on the overall system design, this may be passed through a further level of interrupt collection (interrupt controller). On receipt of the interrupt signal, the CPU enters the interrupt handler (Refer to the AIC programmer datasheet). To ascertain which interrupt has been generated, read the interrupt status register. Note that this register clears itself when read. At reset, all interrupts are disabled. To enable an interrupt, write to interrupt enable register with the pertinent interrupt bit set to 1. To disable an interrupt, write to interrupt disable register with the pertinent interrupt bit set to 1. To check whether an interrupt is enabled or disabled, read interrupt mask register: if the bit is set to 1, the interrupt is disabled. 37.5.1.6 Transmitting Frames To set up a frame for transmission: 1. Allocate a number (n) of buffers of 128 bytes in system memory. 2. Allocate an area of system memory for transmit data. This does not have to be contiguous, varying byte lengths can be used as long as they conclude on byte borders. 3. Set-up the transmit buffer list. 4. Set the network control register to enable transmission and enable interrupts. 5. Write data for transmission into these buffers. 6. Write the address to transmit buffer descriptor queue pointer. 7. Write control and length to word one of the transmit buffer descriptor entry. 8. Write to the transmit start bit in the network control register. 37.5.1.7 Receiving Frames When a frame is received and the receive circuits are enabled, the EMAC checks the address and, in the following cases, the frame is written to system memory:  if it matches one of the four specific address registers.  if it matches the hash address function.  if it is a broadcast address (0xFFFFFFFFFFFF) and broadcasts are allowed.  if the EMAC is configured to copy all frames. The register receive buffer queue pointer points to the next entry (see Table 37-1 on page 835) and the EMAC uses this as the address in system memory to write the frame to. Once the frame has been completely and successfully received and written to system memory, the EMAC then updates the receive buffer descriptor entry with the reason for the address match and marks the area as being owned by software. Once this is complete an interrupt receive complete is set. Software is then responsible for handling the data in the buffer and then releasing the buffer by writing the ownership bit back to 0. If the EMAC is unable to write the data at a rate to match the incoming frame, then an interrupt receive overrun is set. If there is no receive buffer available, i.e., the next buffer is still owned by software, the interrupt receive buffer not available is set. If the frame is not successfully received, a statistic register is incremented and the frame is discarded without informing software. 846 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6 Ethernet MAC 10/100 (EMAC) User Interface Table 37-6. Register Mapping Offset Register Name Access Reset 0x00 Network Control Register EMAC_NCR Read/Write 0 0x04 Network Configuration Register EMAC_NCFG Read/Write 0x800 0x08 Network Status Register EMAC_NSR Read-only - 0x0C Reserved – – – 0x10 Reserved – – – 0x14 Transmit Status Register EMAC_TSR Read/Write 0x0000_0000 0x18 Receive Buffer Queue Pointer Register EMAC_RBQP Read/Write 0x0000_0000 0x1C Transmit Buffer Queue Pointer Register EMAC_TBQP Read/Write 0x0000_0000 0x20 Receive Status Register EMAC_RSR Read/Write 0x0000_0000 0x24 Interrupt Status Register EMAC_ISR Read/Write 0x0000_0000 0x28 Interrupt Enable Register EMAC_IER Write-only - 0x2C Interrupt Disable Register EMAC_IDR Write-only - 0x30 Interrupt Mask Register EMAC_IMR Read-only 0x0000_7FFF 0x34 Phy Maintenance Register EMAC_MAN Read/Write 0x0000_0000 0x38 Pause Time Register EMAC_PTR Read/Write 0x0000_0000 0x3C Pause Frames Received Register EMAC_PFR Read/Write 0x0000_0000 0x40 Frames Transmitted Ok Register EMAC_FTO Read/Write 0x0000_0000 0x44 Single Collision Frames Register EMAC_SCF Read/Write 0x0000_0000 0x48 Multiple Collision Frames Register EMAC_MCF Read/Write 0x0000_0000 0x4C Frames Received Ok Register EMAC_FRO Read/Write 0x0000_0000 0x50 Frame Check Sequence Errors Register EMAC_FCSE Read/Write 0x0000_0000 0x54 Alignment Errors Register EMAC_ALE Read/Write 0x0000_0000 0x58 Deferred Transmission Frames Register EMAC_DTF Read/Write 0x0000_0000 0x5C Late Collisions Register EMAC_LCOL Read/Write 0x0000_0000 0x60 Excessive Collisions Register EMAC_ECOL Read/Write 0x0000_0000 0x64 Transmit Underrun Errors Register EMAC_TUND Read/Write 0x0000_0000 0x68 Carrier Sense Errors Register EMAC_CSE Read/Write 0x0000_0000 0x6C Receive Resource Errors Register EMAC_RRE Read/Write 0x0000_0000 0x70 Receive Overrun Errors Register EMAC_ROV Read/Write 0x0000_0000 0x74 Receive Symbol Errors Register EMAC_RSE Read/Write 0x0000_0000 0x78 Excessive Length Errors Register EMAC_ELE Read/Write 0x0000_0000 0x7C Receive Jabbers Register EMAC_RJA Read/Write 0x0000_0000 0x80 Undersize Frames Register EMAC_USF Read/Write 0x0000_0000 0x84 SQE Test Errors Register EMAC_STE Read/Write 0x0000_0000 0x88 Received Length Field Mismatch Register EMAC_RLE Read/Write 0x0000_0000 SAM9M11 [DATASHEET] 847 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 37-6. Register Mapping (Continued) Offset Register Name Access Reset 0x90 Hash Register Bottom [31:0] Register EMAC_HRB Read/Write 0x0000_0000 0x94 Hash Register Top [63:32] Register EMAC_HRT Read/Write 0x0000_0000 0x98 Specific Address 1 Bottom Register EMAC_SA1B Read/Write 0x0000_0000 0x9C Specific Address 1 Top Register EMAC_SA1T Read/Write 0x0000_0000 0xA0 Specific Address 2 Bottom Register EMAC_SA2B Read/Write 0x0000_0000 0xA4 Specific Address 2 Top Register EMAC_SA2T Read/Write 0x0000_0000 0xA8 Specific Address 3 Bottom Register EMAC_SA3B Read/Write 0x0000_0000 0xAC Specific Address 3 Top Register EMAC_SA3T Read/Write 0x0000_0000 0xB0 Specific Address 4 Bottom Register EMAC_SA4B Read/Write 0x0000_0000 0xB4 Specific Address 4 Top Register EMAC_SA4T Read/Write 0x0000_0000 0xB8 Type ID Checking Register EMAC_TID Read/Write 0x0000_0000 0xC0 User Input/Output Register EMAC_USRIO Read/Write 0x0000_0000 0xC4 Wake on LAN Register EMAC_WOL Read/Write 0x0000_0000 0xC8–0xFC Reserved – – – 848 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.1 Network Control Register Name: EMAC_NCR Address: 0xFFFBC000 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – THALT TSTART BP 7 6 5 4 3 2 1 0 WESTAT INCSTAT CLRSTAT MPE TE RE LLB LB • LB: LoopBack Asserts the loopback signal to the PHY. • LLB: Loopback local Connects txd to rxd, tx_en to rx_dv, forces full duplex and drives rx_clk and tx_clk with pclk divided by 4. rx_clk and tx_clk may glitch as the EMAC is switched into and out of internal loop back. It is important that receive and transmit circuits have already been disabled when making the switch into and out of internal loop back. • RE: Receive enable When set, enables the EMAC to receive data. When reset, frame reception stops immediately and the receive FIFO is cleared. The receive queue pointer register is unaffected. • TE: Transmit enable When set, enables the Ethernet transmitter to send data. When reset transmission, stops immediately, the transmit FIFO and control registers are cleared and the transmit queue pointer register resets to point to the start of the transmit descrip- tor list. • MPE: Management port enable Set to one to enable the management port. When zero, forces MDIO to high impedance state and MDC low. • CLRSTAT: Clear statistics registers This bit is write only. Writing a one clears the statistics registers. • INCSTAT: Increment statistics registers This bit is write only. Writing a one increments all the statistics registers by one for test purposes. • WESTAT: Write enable for statistics registers Setting this bit to one makes the statistics registers writable for functional test purposes. • BP: Back pressure If set in half duplex mode, forces collisions on all received frames. SAM9M11 [DATASHEET] 849 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• TSTART: Start transmission Writing one to this bit starts transmission. • THALT: Transmit halt Writing one to this bit halts transmission as soon as any ongoing frame transmission ends. 850 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.2 Network Configuration Register Name: EMAC_NCFG Address: 0xFFFBC004 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – IRXFCS EFRHD DRFCS RLCE 15 14 13 12 11 10 9 8 RBOF PAE RTY CLK – BIG 7 6 5 4 3 2 1 0 UNI MTI NBC CAF JFRAME – FD SPD • SPD: Speed Set to 1 to indicate 100 Mbit/s operation, 0 for 10 Mbit/s. The value of this pin is reflected on the speed pin. • FD: Full Duplex If set to 1, the transmit block ignores the state of collision and carrier sense and allows receive while transmitting. Also con- trols the half_duplex pin. • CAF: Copy All Frames When set to 1, all valid frames are received. • JFRAME: Jumbo Frames Set to one to enable jumbo frames of up to 10240 bytes to be accepted. • NBC: No Broadcast When set to 1, frames addressed to the broadcast address of all ones are not received. • MTI: Multicast Hash Enable When set, multicast frames are received when the 6-bit hash function of the destination address points to a bit that is set in the hash register. • UNI: Unicast Hash Enable When set, unicast frames are received when the 6-bit hash function of the destination address points to a bit that is set in the hash register. • BIG: Receive 1536 bytes frames Setting this bit means the EMAC receives frames up to 1536 bytes in length. Normally, the EMAC would reject any frame above 1518 bytes. SAM9M11 [DATASHEET] 851 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• CLK: MDC clock divider Set according to system clock speed. This determines by what number system clock is divided to generate MDC. For con- formance with 802.3, MDC must not exceed 2.5 MHz (MDC is only active during MDIO read and write operations) . CLK MDC 00 MCK divided by 8 (MCK up to 20 MHz) 01 MCK divided by 16 (MCK up to 40 MHz) 10 MCK divided by 32 (MCK up to 80 MHz) 11 MCK divided by 64 (MCK up to 160 MHz) • RTY: Retry test Must be set to zero for normal operation. If set to one, the back off between collisions is always one slot time. Setting this bit to one helps testing the too many retries condition. Also used in the pause frame tests to reduce the pause counters decrement time from 512 bit times, to every rx_clk cycle. • PAE: Pause Enable When set, transmission pauses when a valid pause frame is received. • RBOF: Receive Buffer Offset Indicates the number of bytes by which the received data is offset from the start of the first receive buffer. RBOF Offset 00 No offset from start of receive buffer 01 One-byte offset from start of receive buffer 10 Two-byte offset from start of receive buffer 11 Three-byte offset from start of receive buffer • RLCE: Receive Length field Checking Enable When set, frames with measured lengths shorter than their length fields are discarded. Frames containing a type ID in bytes 13 and 14 — length/type ID = 0600 — are not be counted as length errors. • DRFCS: Discard Receive FCS When set, the FCS field of received frames are not be copied to memory. • EFRHD: Enable Frames to be received in half-duplex mode while transmitting. • IRXFCS: Ignore RX FCS When set, frames with FCS/CRC errors are not rejected and no FCS error statistics are counted. For normal operation, this bit must be set to 0. 852 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.3 Network Status Register Name: EMAC_NSR Address: 0xFFFBC008 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – IDLE MDIO – • MDIO Returns status of the mdio_in pin. Use the PHY maintenance register for reading managed frames rather than this bit. • IDLE 0: The PHY logic is running. 1: The PHY management logic is idle (i.e., has completed). SAM9M11 [DATASHEET] 853 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.4 Transmit Status Register Name: EMAC_TSR Address: 0xFFFBC014 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – UND COMP BEX TGO RLE COL UBR This register, when read, provides details of the status of a transmit. Once read, individual bits may be cleared by writing 1 to them. It is not possible to set a bit to 1 by writing to the register. • UBR: Used Bit Read Set when a transmit buffer descriptor is read with its used bit set. Cleared by writing a one to this bit. • COL: Collision Occurred Set by the assertion of collision. Cleared by writing a one to this bit. • RLE: Retry Limit exceeded Cleared by writing a one to this bit. • TGO: Transmit Go If high transmit is active. • BEX: Buffers exhausted mid frame If the buffers run out during transmission of a frame, then transmission stops, FCS shall be bad and tx_er asserted. Cleared by writing a one to this bit. • COMP: Transmit Complete Set when a frame has been transmitted. Cleared by writing a one to this bit. • UND: Transmit Underrun Set when transmit DMA was not able to read data from memory, either because the bus was not granted in time, because a not OK hresp(bus error) was returned or because a used bit was read midway through frame transmission. If this occurs, the transmitter forces bad CRC. Cleared by writing a one to this bit. 854 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.5 Receive Buffer Queue Pointer Register Name: EMAC_RBQP Address: 0xFFFBC018 Access: Read/Write 31 30 29 28 27 26 25 24 ADDR 23 22 21 20 19 18 17 16 ADDR 15 14 13 12 11 10 9 8 ADDR 7 6 5 4 3 2 1 0 ADDR – – This register points to the entry in the receive buffer queue (descriptor list) currently being used. It is written with the start location of the receive buffer descriptor list. The lower order bits increment as buffers are used up and wrap to their original values after either 1024 buffers or when the wrap bit of the entry is set. Reading this register returns the location of the descriptor currently being accessed. This value increments as buffers are used. Software should not use this register for determining where to remove received frames from the queue as it con- stantly changes as new frames are received. Software should instead work its way through the buffer descriptor queue checking the used bits. Receive buffer writes also comprise bursts of two words and, as with transmit buffer reads, it is recommended that bit 2 is always written with zero to prevent a burst crossing a 1K boundary, in violation of section 3.6 of the AMBA specification. • ADDR: Receive buffer queue pointer address Written with the address of the start of the receive queue, reads as a pointer to the current buffer being used. SAM9M11 [DATASHEET] 855 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.6 Transmit Buffer Queue Pointer Register Name: EMAC_TBQP Address: 0xFFFBC01C Access: Read/Write 31 30 29 28 27 26 25 24 ADDR 23 22 21 20 19 18 17 16 ADDR 15 14 13 12 11 10 9 8 ADDR 7 6 5 4 3 2 1 0 ADDR – – This register points to the entry in the transmit buffer queue (descriptor list) currently being used. It is written with the start location of the transmit buffer descriptor list. The lower order bits increment as buffers are used up and wrap to their origi- nal values after either 1024 buffers or when the wrap bit of the entry is set. This register can only be written when bit 3 in the transmit status register is low. As transmit buffer reads consist of bursts of two words, it is recommended that bit 2 is always written with zero to prevent a burst crossing a 1K boundary, in violation of section 3.6 of the AMBA specification. • ADDR: Transmit buffer queue pointer address Written with the address of the start of the transmit queue, reads as a pointer to the first buffer of the frame being transmit- ted or about to be transmitted. 856 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.7 Receive Status Register Name: EMAC_RSR Address: 0xFFFBC020 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – OVR REC BNA This register, when read, provides details of the status of a receive. Once read, individual bits may be cleared by writing 1 to them. It is not possible to set a bit to 1 by writing to the register. • BNA: Buffer Not Available An attempt was made to get a new buffer and the pointer indicated that it was owned by the processor. The DMA rereads the pointer each time a new frame starts until a valid pointer is found. This bit is set at each attempt that fails even if it has not had a successful pointer read since it has been cleared. Cleared by writing a one to this bit. • REC: Frame Received One or more frames have been received and placed in memory. Cleared by writing a one to this bit. • OVR: Receive Overrun The DMA block was unable to store the receive frame to memory, either because the bus was not granted in time or because a not OK hresp(bus error) was returned. The buffer is recovered if this happens. Cleared by writing a one to this bit. SAM9M11 [DATASHEET] 857 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.8 Interrupt Status Register Name: EMAC_ISR Address: 0xFFFBC024 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – WOL PTZ PFR HRESP ROVR – – 7 6 5 4 3 2 1 0 TCOMP TXERR RLE TUND TXUBR RXUBR RCOMP MFD • MFD: Management Frame Done The PHY maintenance register has completed its operation. Cleared on read. • RCOMP: Receive Complete A frame has been stored in memory. Cleared on read. • RXUBR: Receive Used Bit Read Set when a receive buffer descriptor is read with its used bit set. Cleared on read. • TXUBR: Transmit Used Bit Read Set when a transmit buffer descriptor is read with its used bit set. Cleared on read. • TUND: Ethernet Transmit Buffer Underrun The transmit DMA did not fetch frame data in time for it to be transmitted or hresp returned not OK. Also set if a used bit is read mid-frame or when a new transmit queue pointer is written. Cleared on read. • RLE: Retry Limit Exceeded Cleared on read. • TXERR: Transmit Error Transmit buffers exhausted in mid-frame - transmit error. Cleared on read. • TCOMP: Transmit Complete Set when a frame has been transmitted. Cleared on read. • ROVR: Receive Overrun Set when the receive overrun status bit gets set. Cleared on read. • HRESP: Hresp not OK Set when the DMA block sees a bus error. Cleared on read. 858 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• PFR: Pause Frame Received Indicates a valid pause has been received. Cleared on a read. • PTZ: Pause Time Zero • Set when the pause time register, 0x38 decrements to zero. Cleared on a read. • WOL: Wake On LAN Set when a WOL event has been triggered (This flag can be set even if the EMAC is not clocked). Cleared on a read. SAM9M11 [DATASHEET] 859 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.9 Interrupt Enable Register Name: EMAC_IER Address: 0xFFFBC028 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – WOL PTZ PFR HRESP ROVR – – 7 6 5 4 3 2 1 0 TCOMP TXERR RLE TUND TXUBR RXUBR RCOMP MFD • MFD: Management Frame sent Enable management done interrupt. • RCOMP: Receive Complete Enable receive complete interrupt. • RXUBR: Receive Used Bit Read Enable receive used bit read interrupt. • TXUBR: Transmit Used Bit Read Enable transmit used bit read interrupt. • TUND: Ethernet Transmit Buffer Underrun Enable transmit underrun interrupt. • RLE: Retry Limit Exceeded Enable retry limit exceeded interrupt. • TXERR Enable transmit buffers exhausted in mid-frame interrupt. • TCOMP: Transmit Complete Enable transmit complete interrupt. • ROVR: Receive Overrun Enable receive overrun interrupt. • HRESP: Hresp not OK Enable Hresp not OK interrupt. • PFR: Pause Frame Received Enable pause frame received interrupt. 860 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• PTZ: Pause Time Zero Enable pause time zero interrupt. • WOL: Wake On LAN Enable Wake On LAN interrupt. SAM9M11 [DATASHEET] 861 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.10Interrupt Disable Register Name: EMAC_IDR Address: 0xFFFBC02C Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – WOL PTZ PFR HRESP ROVR – – 7 6 5 4 3 2 1 0 TCOMP TXERR RLE TUND TXUBR RXUBR RCOMP MFD • MFD: Management Frame sent Disable management done interrupt. • RCOMP: Receive Complete Disable receive complete interrupt. • RXUBR: Receive Used Bit Read Disable receive used bit read interrupt. • TXUBR: Transmit Used Bit Read Disable transmit used bit read interrupt. • TUND: Ethernet Transmit Buffer Underrun Disable transmit underrun interrupt. • RLE: Retry Limit Exceeded Disable retry limit exceeded interrupt. • TXERR Disable transmit buffers exhausted in mid-frame interrupt. • TCOMP: Transmit Complete Disable transmit complete interrupt. • ROVR: Receive Overrun Disable receive overrun interrupt. • HRESP: Hresp not OK Disable Hresp not OK interrupt. • PFR: Pause Frame Received Disable pause frame received interrupt. 862 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• PTZ: Pause Time Zero Disable pause time zero interrupt. • WOL: Wake On LAN Disable Wake On LAN interrupt. SAM9M11 [DATASHEET] 863 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.11 Interrupt Mask Register Name: EMAC_IMR Address: 0xFFFBC030 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – WOL PTZ PFR HRESP ROVR – – 7 6 5 4 3 2 1 0 TCOMP TXERR RLE TUND TXUBR RXUBR RCOMP MFD • MFD: Management Frame sent Management done interrupt masked. • RCOMP: Receive Complete Receive complete interrupt masked. • RXUBR: Receive Used Bit Read Receive used bit read interrupt masked. • TXUBR: Transmit Used Bit Read Transmit used bit read interrupt masked. • TUND: Ethernet Transmit Buffer Underrun Transmit underrun interrupt masked. • RLE: Retry Limit Exceeded Retry limit exceeded interrupt masked. • TXERR Transmit buffers exhausted in mid-frame interrupt masked. • TCOMP: Transmit Complete Transmit complete interrupt masked. • ROVR: Receive Overrun Receive overrun interrupt masked. • HRESP: Hresp not OK Hresp not OK interrupt masked. • PFR: Pause Frame Received Pause frame received interrupt masked. 864 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• PTZ: Pause Time Zero Pause time zero interrupt masked. • WOL: Wake On LAN Wake On LAN interrupt masked. SAM9M11 [DATASHEET] 865 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.12PHY Maintenance Register Name: EMAC_MAN Address: 0xFFFBC034 Access: Read/Write 31 30 29 28 27 26 25 24 SOF RW PHYA 23 22 21 20 19 18 17 16 PHYA REGA CODE 15 14 13 12 11 10 9 8 DATA 7 6 5 4 3 2 1 0 DATA • DATA For a write operation this is written with the data to be written to the PHY. After a read operation this contains the data read from the PHY. • CODE Must be written to 10. Reads as written. • REGA: Register Address Specifies the register in the PHY to access. • PHYA: PHY Address • RW: Read-write 10 is read; 01 is write. Any other value is an invalid PHY management frame • SOF: Start of frame Must be written 01 for a valid frame. 866 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.13Pause Time Register Name: EMAC_PTR Address: 0xFFFBC038 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 PTIME 7 6 5 4 3 2 1 0 PTIME • PTIME: Pause Time Stores the current value of the pause time register which is decremented every 512 bit times. SAM9M11 [DATASHEET] 867 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.14Hash Register Bottom Name: EMAC_HRB Address: 0xFFFBC090 Access: Read/Write 31 30 29 28 27 26 25 24 ADDR 23 22 21 20 19 18 17 16 ADDR 15 14 13 12 11 10 9 8 ADDR 7 6 5 4 3 2 1 0 ADDR • ADDR Bits 31:0 of the hash address register. See “Hash Addressing” on page 841. 868 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.15Hash Register Top Name: EMAC_HRT Address: 0xFFFBC094 Access: Read/Write 31 30 29 28 27 26 25 24 ADDR 23 22 21 20 19 18 17 16 ADDR 15 14 13 12 11 10 9 8 ADDR 7 6 5 4 3 2 1 0 ADDR • ADDR Bits 63:32 of the hash address register. See “Hash Addressing” on page 841. SAM9M11 [DATASHEET] 869 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.16Specific Address 1 Bottom Register Name: EMAC_SA1B Address: 0xFFFBC098 Access: Read/Write 31 30 29 28 27 26 25 24 ADDR 23 22 21 20 19 18 17 16 ADDR 15 14 13 12 11 10 9 8 ADDR 7 6 5 4 3 2 1 0 ADDR • ADDR Least significant bits of the destination address. Bit zero indicates whether the address is multicast or unicast and corre- sponds to the least significant bit of the first byte received. 870 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.17Specific Address 1 Top Register Name: EMAC_SA1T Address: 0xFFFBC09C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 ADDR 7 6 5 4 3 2 1 0 ADDR • ADDR The most significant bits of the destination address, that is bits 47 to 32. SAM9M11 [DATASHEET] 871 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.18Specific Address 2 Bottom Register Name: EMAC_SA2B Address: 0xFFFBC0A0 Access: Read/Write 31 30 29 28 27 26 25 24 ADDR 23 22 21 20 19 18 17 16 ADDR 15 14 13 12 11 10 9 8 ADDR 7 6 5 4 3 2 1 0 ADDR • ADDR Least significant bits of the destination address. Bit zero indicates whether the address is multicast or unicast and corre- sponds to the least significant bit of the first byte received. 872 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.19Specific Address 2 Top Register Name: EMAC_SA2T Address: 0xFFFBC0A4 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 ADDR 7 6 5 4 3 2 1 0 ADDR • ADDR The most significant bits of the destination address, that is bits 47 to 32. SAM9M11 [DATASHEET] 873 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.20Specific Address 3 Bottom Register Name: EMAC_SA3B Address: 0xFFFBC0A8 Access: Read/Write 31 30 29 28 27 26 25 24 ADDR 23 22 21 20 19 18 17 16 ADDR 15 14 13 12 11 10 9 8 ADDR 7 6 5 4 3 2 1 0 ADDR • ADDR Least significant bits of the destination address. Bit zero indicates whether the address is multicast or unicast and corre- sponds to the least significant bit of the first byte received. 874 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.21Specific Address 3 Top Register Name: EMAC_SA3T Address: 0xFFFBC0AC Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 ADDR 7 6 5 4 3 2 1 0 ADDR • ADDR The most significant bits of the destination address, that is bits 47 to 32. SAM9M11 [DATASHEET] 875 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.22Specific Address 4 Bottom Register Name: EMAC_SA4B Address: 0xFFFBC0B0 Access: Read/Write 31 30 29 28 27 26 25 24 ADDR 23 22 21 20 19 18 17 16 ADDR 15 14 13 12 11 10 9 8 ADDR 7 6 5 4 3 2 1 0 ADDR • ADDR Least significant bits of the destination address. Bit zero indicates whether the address is multicast or unicast and corre- sponds to the least significant bit of the first byte received. 876 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.23Specific Address 4 Top Register Name: EMAC_SA4T Address: 0xFFFBC0B4 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 ADDR 7 6 5 4 3 2 1 0 ADDR • ADDR The most significant bits of the destination address, that is bits 47 to 32. SAM9M11 [DATASHEET] 877 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.24Type ID Checking Register Name: EMAC_TID Address: 0xFFFBC0B8 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 TID 7 6 5 4 3 2 1 0 TID • TID: Type ID Checking For use in comparisons with received frames TypeID/Length field. 878 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.25User Input/Output Register Name: EMAC_USRIO Address: 0xFFFBC0C0 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – CLKEN RMII • RMII When set, this bit enables the RMII operation mode. When reset, it selects the MII mode. • CLKEN When set, this bit enables the transceiver input clock. Setting this bit to 0 reduces power consumption when the treasurer is not used. SAM9M11 [DATASHEET] 879 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.26Wake-on-LAN Register Name: EMAC_WOL Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – MTI SA1 ARP MAG 15 14 13 12 11 10 9 8 IP 7 6 5 4 3 2 1 0 IP • IP: ARP request IP address Written to define the least significant 16 bits of the target IP address that is matched to generate a Wake-on-LAN event. A value of zero does not generate an event, even if this is matched by the received frame. • MAG: Magic packet event enable When set, magic packet events causes the wol output to be asserted. • ARP: ARP request event enable When set, ARP request events causes the wol output to be asserted. • SA1: Specific address register 1 event enable When set, specific address 1 events causes the wol output to be asserted. • MTI: Multicast hash event enable When set, multicast hash events causes the wol output to be asserted. 880 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27EMAC Statistic Registers These registers reset to zero on a read and stick at all ones when they count to their maximum value. They should be read frequently enough to prevent loss of data. The receive statistics registers are only incremented when the receive enable bit is set in the network control register. To write to these registers, bit 7 must be set in the network control register. The statis- tics register block contains the following registers. SAM9M11 [DATASHEET] 881 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.1 Pause Frames Received Register Name: EMAC_PFR Address: 0xFFFBC03C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 FROK 7 6 5 4 3 2 1 0 FROK • FROK: Pause Frames Received OK A 16-bit register counting the number of good pause frames received. A good frame has a length of 64 to 1518 (1536 if bit 8 set in network configuration register) and has no FCS, alignment or receive symbol errors. 882 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.2 Frames Transmitted OK Register Name: EMAC_FTO Address: 0xFFFBC040 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 FTOK 15 14 13 12 11 10 9 8 FTOK 7 6 5 4 3 2 1 0 FTOK • FTOK: Frames Transmitted OK A 24-bit register counting the number of frames successfully transmitted, i.e., no underrun and not too many retries. SAM9M11 [DATASHEET] 883 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.3 Single Collision Frames Register Name: EMAC_SCF Address: 0xFFFBC044 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 SCF 7 6 5 4 3 2 1 0 SCF • SCF: Single Collision Frames A 16-bit register counting the number of frames experiencing a single collision before being successfully transmitted, i.e., no underrun. 884 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.4 Multicollision Frames Register Name: EMAC_MCF Address: 0xFFFBC048 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 MCF 7 6 5 4 3 2 1 0 MCF • MCF: Multicollision Frames A 16-bit register counting the number of frames experiencing between two and fifteen collisions prior to being successfully transmitted, i.e., no underrun and not too many retries. SAM9M11 [DATASHEET] 885 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.5 Frames Received OK Register Name: EMAC_FRO Address: 0xFFFBC04C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 FROK 15 14 13 12 11 10 9 8 FROK 7 6 5 4 3 2 1 0 FROK • FROK: Frames Received OK A 24-bit register counting the number of good frames received, i.e., address recognized and successfully copied to mem- ory. A good frame is of length 64 to 1518 bytes (1536 if bit 8 set in network configuration register) and has no FCS, alignment or receive symbol errors. 886 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.6 Frames Check Sequence Errors Register Name: EMAC_FCSE Address: 0xFFFBC050 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 FCSE • FCSE: Frame Check Sequence Errors An 8-bit register counting frames that are an integral number of bytes, have bad CRC and are between 64 and 1518 bytes in length (1536 if bit 8 set in network configuration register). This register is also incremented if a symbol error is detected and the frame is of valid length and has an integral number of bytes. SAM9M11 [DATASHEET] 887 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.7 Alignment Errors Register Name: EMAC_ALE Address: 0xFFFBC054 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 ALE • ALE: Alignment Errors An 8-bit register counting frames that are not an integral number of bytes long and have bad CRC when their length is trun- cated to an integral number of bytes and are between 64 and 1518 bytes in length (1536 if bit 8 set in network configuration register). This register is also incremented if a symbol error is detected and the frame is of valid length and does not have an integral number of bytes. 888 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.8 Deferred Transmission Frames Register Name: EMAC_DTF Address: 0xFFFBC058 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 DTF 7 6 5 4 3 2 1 0 DTF • DTF: Deferred Transmission Frames A 16-bit register counting the number of frames experiencing deferral due to carrier sense being active on their first attempt at transmission. Frames involved in any collision are not counted nor are frames that experienced a transmit underrun. SAM9M11 [DATASHEET] 889 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.9 Late Collisions Register Name: EMAC_LCOL Address: 0xFFFBC05C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 LCOL • LCOL: Late Collisions An 8-bit register counting the number of frames that experience a collision after the slot time (512 bits) has expired. A late collision is counted twice; i.e., both as a collision and a late collision. 890 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.10 Excessive Collisions Register Name: EMAC_ECOL Address: 0xFFFBC060 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 EXCOL • EXCOL: Excessive Collisions An 8-bit register counting the number of frames that failed to be transmitted because they experienced 16 collisions. SAM9M11 [DATASHEET] 891 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.11 Transmit Underrun Errors Register Name: EMAC_TUND Address: 0xFFFBC064 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 TUND • TUND: Transmit Underruns An 8-bit register counting the number of frames not transmitted due to a transmit DMA underrun. If this register is incre- mented, then no other statistics register is incremented. 892 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.12 Carrier Sense Errors Register Name: EMAC_CSE Address: 0xFFFBC068 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 CSE • CSE: Carrier Sense Errors An 8-bit register counting the number of frames transmitted where carrier sense was not seen during transmission or where carrier sense was deasserted after being asserted in a transmit frame without collision (no underrun). Only incre- mented in half-duplex mode. The only effect of a carrier sense error is to increment this register. The behavior of the other statistics registers is unaffected by the detection of a carrier sense error. SAM9M11 [DATASHEET] 893 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.13 Receive Resource Errors Register Name: EMAC_RRE Address: 0xFFFBC06C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 RRE 7 6 5 4 3 2 1 0 RRE • RRE: Receive Resource Errors A 16-bit register counting the number of frames that were address matched but could not be copied to memory because no receive buffer was available. 894 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.14 Receive Overrun Errors Register Name: EMAC_ROV Address: 0xFFFBC070 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 ROVR • ROVR: Receive Overrun An 8-bit register counting the number of frames that are address recognized but were not copied to memory due to a receive DMA overrun. SAM9M11 [DATASHEET] 895 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.15 Receive Symbol Errors Register Name: EMAC_RSE Address: 0xFFFBC074 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 RSE • RSE: Receive Symbol Errors An 8-bit register counting the number of frames that had rx_er asserted during reception. Receive symbol errors are also counted as an FCS or alignment error if the frame is between 64 and 1518 bytes in length (1536 if bit 8 is set in the network configuration register). If the frame is larger, it is recorded as a jabber error. 896 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.16 Excessive Length Errors Register Name: EMAC_ELE Address: 0xFFFBC078 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 EXL • EXL: Excessive Length Errors An 8-bit register counting the number of frames received exceeding 1518 bytes (1536 if bit 8 set in network configuration register) in length but do not have either a CRC error, an alignment error nor a receive symbol error. SAM9M11 [DATASHEET] 897 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.17 Receive Jabbers Register Name: EMAC_RJA Address: 0xFFFBC07C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 RJB • RJB: Receive Jabbers An 8-bit register counting the number of frames received exceeding 1518 bytes (1536 if bit 8 set in network configuration register) in length and have either a CRC error, an alignment error or a receive symbol error. 898 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.18 Undersize Frames Register Name: EMAC_USF Address: 0xFFFBC080 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 USF • USF: Undersize Frames An 8-bit register counting the number of frames received less than 64 bytes in length but do not have either a CRC error, an alignment error or a receive symbol error. SAM9M11 [DATASHEET] 899 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.19 SQE Test Errors Register Name: EMAC_STE Address: 0xFFFBC084 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 SQER • SQER: SQE Test Errors An 8-bit register counting the number of frames where col was not asserted within 96 bit times (an interframe gap) of tx_en being deasserted in half duplex mode. 900 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

37.6.27.20 Received Length Field Mismatch Register Name: EMAC_RLE Address: 0xFFFBC088 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 RLFM • RLFM: Receive Length Field Mismatch An 8-bit register counting the number of frames received that have a measured length shorter than that extracted from its length field. Checking is enabled through bit 16 of the network configuration register. Frames containing a type ID in bytes 13 and 14 (i.e., length/type ID ≥ 0x0600) are not counted as length field errors, neither are excessive length frames. SAM9M11 [DATASHEET] 901 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

38. USB High Speed Host Port (UHPHS) 38.1 Description The USB High Speed Host Port (UHPHS) interfaces the USB with the host application. It handles Open HCI protocol (Open Host Controller Interface) as well as Enhanced HCI protocol (Enhanced Host Controller Interface). 38.2 Embedded Characteristics The SAM9M11 features USB communication ports as follows:  2 Ports USB Host full speed OHCI and High speed EHCI  1 Device High speed USB Host Port A is directly connected to the first UTMI transceiver. The Host Port B is multiplexed with the USB device High speed and connected to the second UTMI port. The selection between Host Port B and USB device high speed is controlled by a the UDPHS enable bit located in the UDPHS_CTRL register. Figure 38-1. USB Selection HS HS Transceiver Transceiver EN_UDPHS 0 1 PA PB HS HS EHCI USB FS OHCI DMA DMA  Compliant with Enhanced HCI Rev 1.0 Specification ̶ Compliant with USB V2.0 High-speed and Full-speed Specification ̶ Supports Both High-speed 480 Mbps and Full-speed 12 Mbps USB devices  Compliant with Open HCI Rev 1.0 Specification ̶ Compliant with USB V2.0 Full-speed and Low-speed Specification ̶ Supports Both Low-speed 1.5 Mbps and Full-speed 12 Mbps USB devices  Root Hub Integrated with 2 Downstream USB Ports  Shared Embedded USB Transceivers 38.2.1 EHCI The USB Host Port controller is fully compliant with the Enhanced HCI specification. The USB Host Port User Interface (registers description) can be found in the Enhanced HCI Rev 1.0 Specification available on www.intel.com. The standard EHCI USB stack driver can be easily ported to Atmel’s architecture in the same way all existing class drivers run, without hardware specialization. 38.2.2 OHCI The USB Host Port integrates a root hub and transceivers on downstream ports. It provides several Full-speed half-duplex serial communication ports at a baud rate of 12 Mbit/s. Up to 127 USB devices (printer, camera, mouse, keyboard, disk, etc.) and the USB hub can be connected to the USB host in the USB “tiered star” topology. 902 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The USB Host Port controller is fully compliant with the Open HCI specification. The USB Host Port User Interface (registers description) can be found in the Open HCI Rev 1.0 Specification available on www.hp.com. The standard OHCI USB stack driver can be easily ported to Atmel’s architecture, in the same way all existing class drivers run without hardware specialization. This means that all standard class devices are automatically detected and available to the user’s application. As an example, integrating an HID (Human Interface Device) class driver provides a plug & play feature for all USB keyboards and mouses. 38.3 Block Diagram Figure 38-2. Block Diagram Root HCI List Processor Hub Registers Slave Block Block OHCI Control ED & TD AHB Slave Registers Regsisters PORT S/M 1 Root Hub and Host SIE PORT S/M 0 Embedded USB HCI Data AHB FIFO 64 x 8 v2.0 High-speed Transceiver Master Block Master HFSDPB HFSDMB USB transceiver HHSDPB HHSDMB HFSDPA HFSDMA USB transceiver SOF HHSDPA generator HHSDMA HCI Packet Slave Block Buffer EHCI Control FIFO AHB Registers Slave List Processor HCI Data AHB Master Block Master Access to the USB host operational registers is achieved through the AHB bus slave interface. The Open HCI host controller and Enhanced HCI host controller initialize master DMA transfers through the AHB bus master interface as follows:  Fetches endpoint descriptors and transfer descriptors  Access to endpoint data from system memory  Access to the HC communication area  Write status and retire transfer descriptor Memory access errors (abort, misalignment) lead to an “Unrecoverable Error” indicated by the corresponding flag in the host controller operational registers. SAM9M11 [DATASHEET] 903 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The USB root hub is integrated in the USB host. Several USB downstream ports are available. The number of downstream ports can be determined by the software driver reading the root hub’s operational registers. Device connection is automatically detected by the USB host port logic. USB physical transceivers are integrated in the product and driven by the root hub’s ports. Over current protection on ports can be activated by the USB host controller. Atmel’s standard product does not dedicate pads to external over current protection. 38.4 Product Dependencies 38.4.1 I/O Lines HFSDPs, HFSDMs, HHSDPs and HHSDMs are not controlled by any PIO controllers. The embedded USB High Speed physical transceivers are controlled by the USB host controller. One transceiver is shared with USB Device (UDP) High Speed. In this case USB Host High Speed Controller uses only Port A, ie, the signals HFSDPA, HFSDMA, HHSDPA and HHSDMA. The port B is driven by the UDP High Speed, the output signals are DFSDP, DFSDM, DHSDP and DHSDM. The transceiver is automatically selected for Device operation once the UDP High Speed is enabled. 38.4.2 Power Management The USB Host High Speed requires a 48 MHz clock for the embedded High-speed transceivers. This clock is provided by the UTMI PLL, it is UPLLCK. To further reduce power consumption the user can stop UTMI PLL (in this case USB high-speed operations are not possible). Nevertheless, as the USB OHCI input clock PLLACK can be selected with the USBS bit in the PMC_USB register, OHCI full-speed operation remains possible. The High-speed transceiver returns a 30 MHz clock to the USB Host controller. The user must program the USB OHCI Input Clock and the USBDIV divider in the PMC_USB register to generate a 48 MHz and a 12 MHz signal with an accuracy of ± 0.25%. Thus the USB Host peripheral receives three clocks from the Power Management Controller (PMC): the Peripheral Clock (MCK domain), the UHP48M and the UHP12M (built-in UHP48M divided by four) used by the OHCI to interface with the bus USB signals (recovered 12 MHz domain) in Full-speed operations. For High-speed operations, the user has to perform the following:  Enable UHP peripheral clock in PMC_PCER  Write PLLCOUNT field in CKGR_UCKR  Enable UPLL with UPLLEN bit in CKGR_UCKR  Wait until UTMI_PLL is locked (LOCKU bit in PMC_SR)  Enable BIAS, with BIASEN bit in CKGR_UCKR  Select UPLLCK as Input clock of OHCI part (USBS bit in PMC_USB register)  Program OHCI clocks (UHP48M and UHP12M) with USBDIV field in PMC_USB register. USBDIV must be 9 (division by 10) if UPLLCK is selected.  Enable OHCI clocks with UHP bit in PMC_SCER 904 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

For OHCI Full-speed operations only, the user has to perform the following:  Enable UHP peripheral clock in PMC_PCER  Select PLLACK as Input clock of OHCI part (USBS bit in PMC_USB register)  Program OHCI clocks (UHP48M and UHP12M) with USBDIV field in PMC_USB register. USBDIV value is to calculated regarding the PLLACK value and USB Full-speed accuracy.  Enable the OHCI clocks with UHP bit in PMC_SCER Figure 38-3. UHP Clock trees UPLL (480 MHz) EHCI 30 MHz AHB Master UTMI transceiver Interface USB 2.0 EHCI Port Host Controller Router EHCI 30 MHz User UTMI transceiver Interface MCK OHCI Master Interface Root Hub USB 1.1 OHCI and Host Controller Host SIE OHCI User Interface M M 2 8 1 4 P P H H U U OHCI clocks 38.4.3 Interrupt The USB host interface has an interrupt line connected to the Advanced Interrupt Controller (AIC). Handling USB host interrupts requires programming the AIC before configuring the UHP HS. SAM9M11 [DATASHEET] 905 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

38.5 Typical Connection Figure 38-4. Board Schematic to Interface UHP High-speed Device Controller PIO (VBUS DETECT) "A" Receptacle 1 = VBUS HHSDM 2 = D- 3 = D+ 39 ± 5% Ω 15k Ω(1) 4 = GND HFSDM 3 4 Shell = Shield (1) HHSDP 22kΩ CRPB 1 2 39 ± 5% Ω HFSDP C : 1µF to 10µF RPB 6K8 ± 1% Ω VBG 10 pF GNDUTMI Note: 1. The values shown on the 22k Ω and 15k Ω resistors are only valid for 3v3 supplied PIOs. 906 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39. USB High Speed Device Port (UDPHS) 39.1 Description The USB High Speed Device Port (UDPHS) is compliant with the Universal Serial Bus (USB), rev 2.0 High Speed device specification. Each endpoint can be configured in one of several USB transfer types. It can be associated with one, two or three banks of a dual-port RAM used to store the current data payload. If two or three banks are used, one DPR bank is read or written by the processor, while the other is read or written by the USB device peripheral. This feature is mandatory for isochronous endpoints. 39.2 Embedded Characteristics The device features USB communication ports as follows:  2 Ports USB Host full speed OHCI and High speed EHCI  1 Device High speed USB Host Port A is directly connected to the first UTMI transceiver. The Host Port B is multiplexed with the USB device High speed and connected to the second UTMI port. The selection between Host Port B and USB device high speed is controlled by a the UDPHS enable bit located in the UDPHS_CTRL register. Figure 39-1. USB Selection HS HS Transceiver Transceiver EN_UDPHS 0 1 PA PB HS HS EHCI USB FS OHCI DMA DMA  USB V2.0 high-speed compliant, 480 Mbits per second  Embedded USB V2.0 UTMI+ high-speed transceiver shared with UHP HS.  Embedded 4-Kbyte dual-port RAM for endpoints  Embedded 6 channels DMA controller  Suspend/Resume logic  Up to 2 or 3 banks for isochronous and bulk endpoints  Seven endpoints: ̶ Endpoint 0: 64 bytes, 1 bank mode ̶ Endpoint 1 & 2: 1024 bytes, 2 banks mode, High Bandwidth, DMA ̶ Endpoint 3 & 4: 1024 bytes, 3 banks mode, DMA ̶ Endpoint 5 & 6: 1024 bytes, 3 banks mode, High Bandwidth, DMA SAM9M11 [DATASHEET] 907 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 39-1. UDPHS Endpoint Description High Endpoint # Mnemonic Nb Bank DMA BandWidth Max. Endpoint Size Endpoint Type 0 EPT_0 1 N N 64 Control 1 EPT_1 2 Y Y 1024 Ctrl/Bulk/Iso(1)/Interrupt 2 EPT_2 2 Y Y 1024 Ctrl/Bulk/Iso(1)/Interrupt 3 EPT_3 3 Y N 1024 Ctrl/Bulk/Iso(1)/Interrupt 4 EPT_4 3 Y N 1024 Ctrl/Bulk/Iso(1)/Interrupt 5 EPT_5 3 Y Y 1024 Ctrl/Bulk/Iso(1)/Interrupt 6 EPT_6 3 Y Y 1024 Ctrl/Bulk/Iso(1)/Interrupt Note: 1. In Isochronous Mode (Iso), it is preferable that High Band Width capability is available. The size of internal DPRAM is 4 Kbyte. Suspend and resume are automatically detected by the UDPHS device, which notifies the processor by raising an interrupt. 908 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.3 Block Diagram Figure 39-2. Block Diagram APB APB bus Interface ctrl DHSDP status DHSDM AHB1 Rd/Wr/Ready AHB bus DMA USB2.0 UTMI DFSDP DP AHB0 CORE DFSDM DM Master APB bus AHB Multiplexer Slave Local AHB Slave EPT interface Alloc 32 bits 16/8 bits DPRAM System Clock USB Clock Domain Domain PMC SAM9M11 [DATASHEET] 909 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.4 Typical Connection Figure 39-3. Board Schematic PIO (VBUS DETECT) "B" Receptacle 1 = VBUS DHSDM 2 = D- 3 = D+ 39 ± 5% Ω 15k Ω(1) 4 = GND DFSDM 1 2 Shell = Shield (1) DHSDP 22kΩ CRPB 3 4 39 ± 5% Ω DFSDP C :1µF to 10µF RPB 6K8 ± 1% Ω VBG 10 pF GNDUTMI Note: 1. The values shown on the 22kΩ and 15kΩ resistors are only valid with 3V3 supplied PIOs. 910 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.5 Functional Description 39.5.1 USB V2.0 High Speed Device Port Introduction The USB V2.0 High Speed Device Port provides communication services between host and attached USB devices. Each device is offered with a collection of communication flows (pipes) associated with each endpoint. Software on the host communicates with a USB Device through a set of communication flows. 39.5.2 USB V2.0 High Speed Transfer Types A communication flow is carried over one of four transfer types defined by the USB device. A device provides several logical communication pipes with the host. To each logical pipe is associated an endpoint. Transfer through a pipe belongs to one of the four transfer types:  Control Transfers: Used to configure a device at attach time and can be used for other device-specific purposes, including control of other pipes on the device.  Bulk Data Transfers: Generated or consumed in relatively large burst quantities and have wide dynamic latitude in transmission constraints.  Interrupt Data Transfers: Used for timely but reliable delivery of data, for example, characters or coordinates with human-perceptible echo or feedback response characteristics.  Isochronous Data Transfers: Occupy a prenegotiated amount of USB bandwidth with a prenegotiated delivery latency. (Also called streaming real time transfers.) As indicated below, transfers are sequential events carried out on the USB bus. Endpoints must be configured according to the transfer type they handle. Table 39-2. USB Communication Flow Transfer Direction Bandwidth Endpoint Size Error Detection Retrying Control Bidirectional Not guaranteed 8,16,32,64 Yes Automatic Isochronous Unidirectional Guaranteed 8–1024 Yes No Interrupt Unidirectional Not guaranteed 8–1024 Yes Yes Bulk Unidirectional Not guaranteed 8–512 Yes Yes SAM9M11 [DATASHEET] 911 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.5.3 USB Transfer Event Definitions A transfer is composed of one or several transactions. Table 39-3. USB Transfer Events Transfer Direction Type Transaction Setup transaction → Data IN transactions → Status OUT transaction CONTROL (bidirectional) Control(1) Setup transaction → Data OUT transactions → Status IN transaction Setup transaction → Status IN transaction Bulk IN IN (device toward host) Interrupt IN Data IN transaction → Data IN transaction Isochronous IN(2) Bulk OUT OUT (host toward device) Interrupt OUT Data OUT transaction → Data OUT transaction Isochronous OUT (2) Notes: 1. Control transfer must use endpoints with one bank and can be aborted using a stall handshake. 2. Isochronous transfers must use endpoints configured with two or three banks. An endpoint handles all transactions related to the type of transfer for which it has been configured. 39.5.4 USB V2.0 High Speed BUS Transactions Each transfer results in one or more transactions over the USB bus. There are five kinds of transactions flowing across the bus in packets: 1. Setup Transaction 2. Data IN Transaction 3. Data OUT Transaction 4. Status IN Transaction 5. Status OUT Transaction 912 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 39-4. Control Read and Write Sequences Setup Stage Data Stage Status Stage Setup TX Data OUT TX Data OUT TX Status IN TX Control Write Setup Stage Data Stage Status Stage Control Read Setup TX Data IN TX Data IN TX Status OUT TX Setup Stage Status Stage No Data Setup TX Status IN TX Control A status IN or OUT transaction is identical to a data IN or OUT transaction. 39.5.5 Endpoint Configuration The endpoint 0 is always a control endpoint, it must be programmed and active in order to be enabled when the End Of Reset interrupt occurs. To configure the endpoints:  Fill the configuration register (UDPHS_EPTCFG) with the endpoint size, direction (IN or OUT), type (CTRL, Bulk, IT, ISO) and the number of banks.  Fill the number of transactions (NB_TRANS) for isochronous endpoints. Note: For control endpoints the direction has no effect.  Verify that the EPT_MAPD flag is set. This flag is set if the endpoint size and the number of banks are correct compared to the FIFO maximum capacity and the maximum number of allowed banks.  Configure control flags of the endpoint and enable it in UDPHS_EPTCTLENBx according to “UDPHS Endpoint Control Register” on page 952. Control endpoints can generate interrupts and use only 1 bank. All endpoints (except endpoint 0) can be configured either as Bulk, Interrupt or Isochronous. See Table 39-1. UDPHS Endpoint Description. The maximum packet size they can accept corresponds to the maximum endpoint size. Note: The endpoint size of 1024 is reserved for isochronous endpoints. SAM9M11 [DATASHEET] 913 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The size of the DPRAM is 4 Kbyte. The DPR is shared by all active endpoints. The memory size required by the active endpoints must not exceed the size of the DPRAM. SIZE_DPRAM = SIZE _EPT0 + NB_BANK_EPT1 x SIZE_EPT1 + NB_BANK_EPT2 x SIZE_EPT2 + NB_BANK_EPT3 x SIZE_EPT3 + NB_BANK_EPT4 x SIZE_EPT4 + NB_BANK_EPT5 x SIZE_EPT5 + NB_BANK_EPT6 x SIZE_EPT6 +... (refer to Section 39.6.8 ”UDPHS Endpoint Configuration Register”) If a user tries to configure endpoints with a size the sum of which is greater than the DPRAM, then the EPT_MAPD is not set. The application has access to the physical block of DPR reserved for the endpoint through a 64 Kbyte logical address space. The physical block of DPR allocated for the endpoint is remapped all along the 64 Kbyte logical address space. The application can write a 64 Kbyte buffer linearly. Figure 39-5. Logical Address Space for DPR Access DPR x banks Logical address 8 to 64 B 8 to 64 B 64 KB 8 to 64 B 8 to1024 B y banks EP0 8 to 64 B ... 8 to1024 B z banks 64 KB 8 to1024 B 8 to1024 B EP1 8 to1024 B ... 8 to1024 B 64 KB EP2 64 KB EP3 ... Configuration examples of UDPHS_EPTCTLx (UDPHS Endpoint Control Register) for Bulk IN endpoint type follow below.  With DMA ̶ AUTO_VALID: Automatically validate the packet and switch to the next bank. ̶ EPT_ENABL: Enable endpoint.  Without DMA: ̶ TX_BK_RDY: An interrupt is generated after each transmission. ̶ EPT_ENABL: Enable endpoint. 914 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Configuration examples of Bulk OUT endpoint type follow below.  With DMA ̶ AUTO_VALID: Automatically validate the packet and switch to the next bank. ̶ EPT_ENABL: Enable endpoint.  Without DMA ̶ RX_BK_RDY: An interrupt is sent after a new packet has been stored in the endpoint FIFO. ̶ EPT_ENABL: Enable endpoint. 39.5.6 Transfer With DMA USB packets of any length may be transferred when required by the UDPHS Device. These transfers always feature sequential addressing. Packet data AHB bursts may be locked on a DMA buffer basis for drastic overall AHB bus bandwidth performance boost with paged memories. These clock-cycle consuming memory row (or bank) changes will then likely not occur, or occur only once instead of dozens times, during a single big USB packet DMA transfer in case another AHB master addresses the memory. This means up to 128-word single-cycle unbroken AHB bursts for Bulk endpoints and 256-word single-cycle unbroken bursts for isochronous endpoints. This maximum burst length is then controlled by the lowest programmed USB endpoint size (EPT_SIZE bit in the UDPHS_EPTCFGx register) and DMA Size (BUFF_LENGTH bit in the UDPHS_DMACONTROLx register). The USB 2.0 device average throughput may be up to nearly 60 MBytes. Its internal slave average access latency decreases as burst length increases due to the 0 wait-state side effect of unchanged endpoints. If at least 0 wait- state word burst capability is also provided by the external DMA AHB bus slaves, each of both DMA AHB busses need less than 50% bandwidth allocation for full USB 2.0 bandwidth usage at 30 MHz, and less than 25% at 60 MHz. The UDPHS DMA Channel Transfer Descriptor is described in “UDPHS DMA Channel Transfer Descriptor” on page 962. Note: In case of debug, be careful to address the DMA to an SRAM address even if a remap is done. SAM9M11 [DATASHEET] 915 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 39-6. Example of DMA Chained List: Transfer Descriptor UDPHS Registers (Current Transfer Descriptor) Next Descriptor Address Transfer Descriptor DMA Channel Address UDPHS Next Descriptor Next Descriptor Address DMA Channel Control DMA Channel Address DMA Channel Address Transfer Descriptor DMA Channel Control Next Descriptor Address DMA Channel Control DMA Channel Address DMA Channel Control Null Memory Area Data Buff 1 Data Buff 2 Data Buff 3 39.5.7 Transfer Without DMA IMPORTANT: If the DMA is not to be used, it is necessary that it be disabled because otherwise it can be enabled by previous versions of software without warning. If this should occur, the DMA can process data before an interrupt without knowledge of the user. The recommended means to disable DMA is as follows: // Reset IP UDPHS AT91C_BASE_UDPHS->UDPHS_CTRL &= ~AT91C_UDPHS_EN_UDPHS; AT91C_BASE_UDPHS->UDPHS_CTRL |= AT91C_UDPHS_EN_UDPHS; // With OR without DMA !!! for( i=1; i<=((AT91C_BASE_UDPHS->UDPHS_IPFEATURES & AT91C_UDPHS_DMA_CHANNEL_NBR)>>4); i++ ) { // RESET endpoint canal DMA: // DMA stop channel command AT91C_BASE_UDPHS->UDPHS_DMA[i].UDPHS_DMACONTROL = 0; // STOP command // Disable endpoint AT91C_BASE_UDPHS->UDPHS_EPT[i].UDPHS_EPTCTLDIS |= 0XFFFFFFFF; // Reset endpoint config AT91C_BASE_UDPHS->UDPHS_EPT[i].UDPHS_EPTCTLCFG = 0; // Reset DMA channel (Buff count and Control field) AT91C_BASE_UDPHS->UDPHS_DMA[i].UDPHS_DMACONTROL = 0x02; // NON STOP command // Reset DMA channel 0 (STOP) AT91C_BASE_UDPHS->UDPHS_DMA[i].UDPHS_DMACONTROL = 0; // STOP command // Clear DMA channel status (read the register for clear it) AT91C_BASE_UDPHS->UDPHS_DMA[i].UDPHS_DMASTATUS = AT91C_BASE_UDPHS->UDPHS_DMA[i].UDPHS_DMASTATUS; } 916 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.5.8 Handling Transactions with USB V2.0 Device Peripheral 39.5.8.1 Setup Transaction The setup packet is valid in the DPR while RX_SETUP is set. Once RX_SETUP is cleared by the application, the UDPHS accepts the next packets sent over the device endpoint. When a valid setup packet is accepted by the UDPHS:  the UDPHS device automatically acknowledges the setup packet (sends an ACK response)  payload data is written in the endpoint  sets the RX_SETUP interrupt  the BYTE_COUNT field in the UDPHS_EPTSTAx register is updated An endpoint interrupt is generated while RX_SETUP in the UDPHS_EPTSTAx register is not cleared. This interrupt is carried out to the microcontroller if interrupts are enabled for this endpoint. Thus, firmware must detect RX_SETUP polling UDPHS_EPTSTAx or catching an interrupt, read the setup packet in the FIFO, then clear the RX_SETUP bit in the UDPHS_EPTCLRSTA register to acknowledge the setup stage. If STALL_SNT was set to 1, then this bit is automatically reset when a setup token is detected by the device. Then, the device still accepts the setup stage. (See Section 39.5.8.5 “STALL” on page 927). 39.5.8.2 NYET NYET is a High Speed only handshake. It is returned by a High Speed endpoint as part of the PING protocol. High Speed devices must support an improved NAK mechanism for Bulk OUT and control endpoints (except setup stage). This mechanism allows the device to tell the host whether it has sufficient endpoint space for the next OUT transfer (see USB 2.0 spec 8.5.1 NAK Limiting via Ping Flow Control). The NYET/ACK response to a High Speed Bulk OUT transfer and the PING response are automatically handled by hardware in the UDPHS_EPTCTLx register (except when the user wants to force a NAK response by using the NYET_DIS bit). If the endpoint responds instead to the OUT/DATA transaction with an NYET handshake, this means that the endpoint accepted the data but does not have room for another data payload. The host controller must return to using a PING token until the endpoint indicates it has space available. Figure 39-7. NYET Example with Two Endpoint Banks data 0 ACK data 1 NYET PING ACK data 0 NYET PING NACK PING ACK t = 0 t = 125 µs t = 250 µs t = 375 µs t = 500 µs t = 625 µs E: empty E': begin to empty F: full Bank 1 E Bank 1 F Bank 1 F Bank 1 F Bank 1 F Bank 1 E' Bank 1 E Bank 0 F Bank 0 E' Bank 0 E Bank 0 E Bank 0 F Bank 0 F Bank 0 F SAM9M11 [DATASHEET] 917 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.5.8.3 Data IN Bulk IN or Interrupt IN Data IN packets are sent by the device during the data or the status stage of a control transfer or during an (interrupt/bulk/isochronous) IN transfer. Data buffers are sent packet by packet under the control of the application or under the control of the DMA channel. There are three ways for an application to transfer a buffer in several packets over the USB:  packet by packet (see below)  64 Kbyte (see below)  DMA (see below) Bulk IN or Interrupt IN: Sending a Packet Under Application Control (Device to Host) The application can write one or several banks. A simple algorithm can be used by the application to send packets regardless of the number of banks associated to the endpoint. Algorithm Description for Each Packet:  The application waits for TX_PK_RDY flag to be cleared in the UDPHS_EPTSTAx register before it can perform a write access to the DPR.  The application writes one USB packet of data in the DPR through the 64 Kbyte endpoint logical memory window.  The application sets TX_PK_RDY flag in the UDPHS_EPTSETSTAx register. The application is notified that it is possible to write a new packet to the DPR by the TX_PK_RDY interrupt. This interrupt can be enabled or masked by setting the TX_PK_RDY bit in the UDPHS_EPTCTLENB/UDPHS_EPTCTLDIS register. Algorithm Description to Fill Several Packets: Using the previous algorithm, the application is interrupted for each packet. It is possible to reduce the application overhead by writing linearly several banks at the same time. The AUTO_VALID bit in the UDPHS_EPTCTLx must be set by writing the AUTO_VALID bit in the UDPHS_EPTCTLENBx register. The auto-valid-bank mechanism allows the transfer of data (IN and OUT) without the intervention of the CPU. This means that bank validation (set TX_PK_RDY or clear the RX_BK_RDY bit) is done by hardware.  The application checks the BUSY_BANK_STA field in the UDPHS_EPTSTAx register. The application must wait that at least one bank is free.  The application writes a number of bytes inferior to the number of free DPR banks for the endpoint. Each time the application writes the last byte of a bank, the TX_PK_RDY signal is automatically set by the UDPHS.  If the last packet is incomplete (i.e., the last byte of the bank has not been written) the application must set the TX_PK_RDY bit in the UDPHS_EPTSETSTAx register. The application is notified that all banks are free, so that it is possible to write another burst of packets by the BUSY_BANK interrupt. This interrupt can be enabled or masked by setting the BUSY_BANK flag in the UDPHS_EPTCTLENB and UDPHS_EPTCTLDIS registers. This algorithm must not be used for isochronous transfer. In this case, the ping-pong mechanism does not operate. A Zero Length Packet can be sent by setting just the TX_PKTRDY flag in the UDPHS_EPTSETSTAx register. 918 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Bulk IN or Interrupt IN: Sending a Buffer Using DMA (Device to Host) The UDPHS integrates a DMA host controller. This DMA controller can be used to transfer a buffer from the memory to the DPR or from the DPR to the processor memory under the UDPHS control. The DMA can be used for all transfer types except control transfer. Example DMA configuration: 1. Program UDPHS_DMAADDRESS x with the address of the buffer that should be transferred. 2. Enable the interrupt of the DMA in UDPHS_IEN 3. Program UDPHS_ DMACONTROLx: ̶ Size of buffer to send: size of the buffer to be sent to the host. ̶ END_B_EN: The endpoint can validate the packet (according to the values programmed in the AUTO_VALID and SHRT_PCKT fields of UDPHS_EPTCTLx.) (See “UDPHS Endpoint Control Register” on page 952 and Figure 39-12. Autovalid with DMA) ̶ END_BUFFIT: generate an interrupt when the BUFF_COUNT in UDPHS_DMASTATUSx reaches 0. ̶ CHANN_ENB: Run and stop at end of buffer The auto-valid-bank mechanism allows the transfer of data (IN & OUT) without the intervention of the CPU. This means that bank validation (set TX_PK_RDY or clear the RX_BK_RDY bit) is done by hardware. A transfer descriptor can be used. Instead of programming the register directly, a descriptor should be programmed and the address of this descriptor is then given to UDPHS_DMANXTDSC to be processed after setting the LDNXT_DSC field (Load Next Descriptor Now) in UDPHS_DMACONTROLx register. The structure that defines this transfer descriptor must be aligned. Each buffer to be transferred must be described by a DMA Transfer descriptor (see “UDPHS DMA Channel Transfer Descriptor” on page 962). Transfer descriptors are chained. Before executing transfer of the buffer, the UDPHS may fetch a new transfer descriptor from the memory address pointed by the UDPHS_DMANXTDSCx register. Once the transfer is complete, the transfer status is updated in the UDPHS_DMASTATUSx register. To chain a new transfer descriptor with the current DMA transfer, the DMA channel must be stopped. To do so, INTDIS_DMA and TX_BK_RDY may be set in the UDPHS_EPTCTLENBx register. It is also possible for the application to wait for the completion of all transfers. In this case the LDNXT_DSC field in the last transfer descriptor UDPHS_DMACONTROLx register must be set to 0 and CHANN_ENB set to 1. Then the application can chain a new transfer descriptor. The INTDIS_DMA can be used to stop the current DMA transfer if an enabled interrupt is triggered. This can be used to stop DMA transfers in case of errors. The application can be notified at the end of any buffer transfer (ENB_BUFFIT bit in the UDPHS_DMACONTROLx register). SAM9M11 [DATASHEET] 919 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 39-8. Data IN Transfer for Endpoint with One Bank Prevous Data IN TX Microcontroller Loads Data in FIFO Data is Sent on USB Bus USB Bus Token IN Data IN 1 ACK Token IN NAK Token IN Data IN 2 ACK Packets TX_PK_RDY Flag (UDPHS_EPTSTAx)Set by firmware Cleared by hardware Set by the firmware Cleared by hardware Interrupt Pending Interrupt Pending TX_COMPLT Flag Payload in FIFO (UDPHS_EPTSTAx) Set by hardware Cleared by firmware Cleared by firmware DPR access by firmware DPR access by hardware FIFO Data IN 1 Load in progress Data IN 2 Content Figure 39-9. Data IN Transfer for Endpoint with Two Banks Microcontroller Microcontroller Load Data IN Bank 1 Microcontroller Load Data IN Bank 0 Load Data IN Bank 0 UDPHS Device Send Bank 0 UDPHS Device Send Bank 1 USB Bus Token IN Data IN ACK Token IN Data IN ACK Packets Set by Firmware, Cleared by Hardware Data Payload Written switch to next bank in FIFO Bank 0 Virtual TX_PK_RDY bank 0 Cleared by Hardware (UDPHS_EPTSTAx) Data Payload Fully Transmitted Virtual TX_PK_RDY bank 1 Set by Firmware, (UDPHS_EPTSTAx) Data Payload Written in FIFO Bank 1 Interrupt Pending TX_COMPLT Set by Hardware Set by Hardware Flag (UDPHS_EPTSTAx) Interrupt Cleared by Firmware FIFO Written by Written by (DPR) Microcontroller Read by USB Device Microcontroller Bank 0 FIFO Written by (DPR) Microcontroller Read by UDPHS Device Bank1 920 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 39-10. Data IN Followed By Status OUT Transfer at the End of a Control Transfer Device Sends the Last Device Sends a Data Payload to Host Status OUT to Host USB Bus Packets Token IN Data IN ACK Token OUT Data OUT (ZLP) ACK Token OUT Data OUT (ZLP) ACK Interrupt Pending RX_BK_RDY (UDPHS_EPTSTAx) Set by Hardware Cleared by Firmware TX_COMPLT (UDPHS_EPTSTAx) Set by Hardware Cleared by Firmware Note: A NAK handshake is always generated at the first status stage token. Figure 39-11. Data OUT Followed by Status IN Transfer Host Sends the Last Device Sends a Status IN Data Payload to the Device to the Host USB Bus Token OUT Data OUT ACK Token IN Data IN ACK Packets Interrupt Pending RX_BK_RDY Cleared by Firmware (UDPHS_EPTSTAx) Set by Hardware TX_PK_RDY (UDPHS_EPTSTAx) Set by Firmware Clear by Hardware Note: Before proceeding to the status stage, the software should determine that there is no risk of extra data from the host (data stage). If not certain (non-predictable data stage length), then the software should wait for a NAK-IN interrupt before proceeding to the status stage. This precaution should be taken to avoid collision in the FIFO. SAM9M11 [DATASHEET] 921 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 39-12. Autovalid with DMA Bank (system) Bank 0 Bank 1 Bank 0 Bank 1 Write write bank 0 write bank 1 write bank 0 bank 0 is full bank 1 is full bank 0 is full Bank 1 Bank 0 IN data 0 IN data 1 IN data 0 Bank (usb) Bank 0 Bank 1 Bank 0 Bank 1 Virtual TX_PK_RDY Bank 0 Virtual TX_PK_RDY Bank 1 TX_PK_RDY (Virtual 0 & Virtual 1) Note: In the illustration above Autovalid validates a bank as full, although this might not be the case, in order to continue processing data and to send to DMA. Isochronous IN Isochronous-IN is used to transmit a stream of data whose timing is implied by the delivery rate. Isochronous transfer provides periodic, continuous communication between host and device. It guarantees bandwidth and low latencies appropriate for telephony, audio, video, etc. If the endpoint is not available (TX_PK_RDY = 0), then the device does not answer to the host. An ERR_FL_ISO interrupt is generated in the UDPHS_EPTSTAx register and once enabled, then sent to the CPU. The STALL_SNT command bit is not used for an ISO-IN endpoint. High Bandwidth Isochronous Endpoint Handling: IN Example For high bandwidth isochronous endpoints, the DMA can be programmed with the number of transactions (BUFF_LENGTH field in UDPHS_DMACONTROLx) and the system should provide the required number of packets per microframe, otherwise, the host will notice a sequencing problem. 922 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

A response should be made to the first token IN recognized inside a microframe under the following conditions:  If at least one bank has been validated, the correct DATAx corresponding to the programmed Number Of Transactions per Microframe (NB_TRANS) should be answered. In case of a subsequent missed or corrupted token IN inside the microframe, the USB 2.0 Core available data bank(s) that should normally have been transmitted during that microframe shall be flushed at its end. If this flush occurs, an error condition is flagged (ERR_FLUSH is set in UDPHS_EPTSTAx).  If no bank is validated yet, the default DATA0 ZLP is answered and underflow is flagged (ERR_FL_ISO is set in UDPHS_EPTSTAx). Then, no data bank is flushed at microframe end.  If no data bank has been validated at the time when a response should be made for the second transaction of NB_TRANS = 3 transactions microframe, a DATA1 ZLP is answered and underflow is flagged (ERR_FL_ISO is set in UDPHS_EPTSTAx). If and only if remaining untransmitted banks for that microframe are available at its end, they are flushed and an error condition is flagged (ERR_FLUSH is set in UDPHS_EPTSTAx).  If no data bank has been validated at the time when a response should be made for the last programmed transaction of a microframe, a DATA0 ZLP is answered and underflow is flagged (ERR_FL_ISO is set in UDPHS_EPTSTAx). If and only if the remaining untransmitted data bank for that microframe is available at its end, it is flushed and an error condition is flagged (ERR_FLUSH is set in UDPHS_EPTSTAx).  If at the end of a microframe no valid token IN has been recognized, no data bank is flushed and no error condition is reported. At the end of a microframe in which at least one data bank has been transmitted, if less than NB_TRANS banks have been validated for that microframe, an error condition is flagged (ERR_TRANS is set in UDPHS_EPTSTAx). Cases of Error (in UDPHS_EPTSTAx)  ERR_FL_ISO: There was no data to transmit inside a microframe, so a ZLP is answered by default.  ERR_FLUSH: At least one packet has been sent inside the microframe, but the number of token IN received is lesser than the number of transactions actually validated (TX_BK_RDY) and likewise with the NB_TRANS programmed.  ERR_TRANS: At least one packet has been sent inside the microframe, but the number of token IN received is lesser than the number of programmed NB_TRANS transactions and the packets not requested were not validated.  ERR_FL_ISO + ERR_FLUSH: At least one packet has been sent inside the microframe, but the data has not been validated in time to answer one of the following token IN.  ERR_FL_ISO + ERR_TRANS: At least one packet has been sent inside the microframe, but the data has not been validated in time to answer one of the following token IN and the data can be discarded at the microframe end.  ERR_FLUSH + ERR_TRANS: The first token IN has been answered and it was the only one received, a second bank has been validated but not the third, whereas NB_TRANS was waiting for three transactions.  ERR_FL_ISO + ERR_FLUSH + ERR_TRANS: The first token IN has been treated, the data for the second Token IN was not available in time, but the second bank has been validated before the end of the microframe. The third bank has not been validated, but three transactions have been set in NB_TRANS. 39.5.8.4 Data OUT Bulk OUT or Interrupt OUT Like data IN, data OUT packets are sent by the host during the data or the status stage of control transfer or during an interrupt/bulk/isochronous OUT transfer. Data buffers are sent packet by packet under the control of the application or under the control of the DMA channel. SAM9M11 [DATASHEET] 923 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Bulk OUT or Interrupt OUT: Receiving a Packet Under Application Control (Host to Device) Algorithm Description for Each Packet:  The application enables an interrupt on RX_BK_RDY.  When an interrupt on RX_BK_RDY is received, the application knows that UDPHS_EPTSTAx register BYTE_COUNT bytes have been received.  The application reads the BYTE_COUNT bytes from the endpoint.  The application clears RX_BK_RDY. Note: If the application does not know the size of the transfer, it may not be a good option to use AUTO_VALID. Because if a zero-length-packet is received, the RX_BK_RDY is automatically cleared by the AUTO_VALID hardware and if the endpoint interrupt is triggered, the software will not find its originating flag when reading the UDPHS_EPTSTAx register. Algorithm to Fill Several Packets:  The application enables the interrupts of BUSY_BANK and AUTO_VALID.  When a BUSY_BANK interrupt is received, the application knows that all banks available for the endpoint have been filled. Thus, the application can read all banks available. If the application does not know the size of the receive buffer, instead of using the BUSY_BANK interrupt, the application must use RX_BK_RDY. Bulk OUT or Interrupt OUT: Sending a Buffer Using DMA (Host To Device) To use the DMA setting, the AUTO_VALID field is mandatory. See Bulk IN or Interrupt IN: Sending a Buffer Using DMA (Device to Host) for more information. DMA Configuration Example: 1. First program UDPHS_DMAADDRESSx with the address of the buffer that should be transferred. 2. Enable the interrupt of the DMA in UDPHS_IEN 3. Program the DMA Channelx Control Register: ̶ Size of buffer to be sent. ̶ END_B_EN: Can be used for OUT packet truncation (discarding of unbuffered packet data) at the end of DMA buffer. ̶ END_BUFFIT: Generate an interrupt when BUFF_COUNT in the UDPHS_DMASTATUSx register reaches 0. ̶ END_TR_EN: End of transfer enable, the UDPHS device can put an end to the current DMA transfer, in case of a short packet. ̶ END_TR_IT: End of transfer interrupt enable, an interrupt is sent after the last USB packet has been transferred by the DMA, if the USB transfer ended with a short packet. (Beneficial when the receive size is unknown.) ̶ CHANN_ENB: Run and stop at end of buffer. For OUT transfer, the bank will be automatically cleared by hardware when the application has read all the bytes in the bank (the bank is empty). Note: When a zero-length-packet is received, RX_BK_RDY bit in UDPHS_EPTSTAx is cleared automatically by AUTO_VALID, and the application knows of the end of buffer by the presence of the END_TR_IT. Note: If the host sends a zero-length packet, and the endpoint is free, then the device sends an ACK. No data is written in the endpoint, the RX_BY_RDY interrupt is generated, and the BYTE_COUNT field in UDPHS_EPTSTAx is null. 924 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 39-13. Data OUT Transfer for Endpoint with One Bank Microcontroller Transfers Data Host Sends Data Payload Host Sends the Next Data Payload Host Resends the Next Data Payload USB Bus Token OUT Data OUT 1 ACK Token OUT Data OUT 2 NAK Token OUT Data OUT 2 ACK Packets Interrupt Pending RX_BK_RDY (UDPHS_EPTSTAx) Set by Hardware Cleared by Firmware, Data Payload Written in FIFO FIFO (DPR) Data OUT 1 Data OUT 1 Data OUT 2 Content Written by UDPHS Device Microcontroller Read Written by UDPHS Device Figure 39-14. Data OUT Transfer for an Endpoint with Two Banks Microcontroller reads Data1 in bank 0, Microcontroller reads Data 2 in bank 1, Host sends first data payload Host sends second data payload Host sends third data payload USB Bus Packets Token OUT Data OUT 1 ACK Token OUT Data OUT 2 ACK Token OUT Data OUT 3 Cleared by Firmware Virtual RX_BK_RDY Interrupt pending Bank 0 Set by Hardware, Data payload written Set by Hardware Cleared by Firmware in FIFO endpoint bank 0 Data Payload written Virtual RX_BK_RDY in FIFO endpoint bank 1 Interrupt pending Bank 1 RX_BK_RDY = (virtual bank 0 | virtual bank 1) (UDPHS_EPTSTAx) FIFO (DPR) Bank 0 Data OUT 1 Data OUT 1 Data OUT 3 Write by UDPHS Device Read by Microcontroller Write in progress FIFO (DPR) Bank 1 Data OUT 2 Data OUT 2 Write by Hardware Read by Microcontroller SAM9M11 [DATASHEET] 925 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

High Bandwidth Isochronous Endpoint OUT Figure 39-15. Bank Management, Example of Three Transactions per Microframe USB bus MDATA0 MDATA1 DATA2 MDATA0 MDATA1 DATA2 Transactions t = 0 t = 52.5 µs t = 125 µs USB line RX_BK_RDY (40% of 125 µs) RX_BK_RDY Microcontroller FIFO Read Bank 1 Read Bank 2 Read Bank 3 Read Bank 1 (DPR) Access USB 2.0 supports individual High Speed isochronous endpoints that require data rates up to 192 Mb/s (24 MB/s): 3x1024 data bytes per microframe. To support such a rate, two or three banks may be used to buffer the three consecutive data packets. The microcontroller (or the DMA) should be able to empty the banks very rapidly (at least 24 MB/s on average). NB_TRANS field in UDPHS_EPTCFGx register = Number Of Transactions per Microframe. If NB_TRANS > 1 then it is High Bandwidth. Example:  If NB_TRANS = 3, the sequence should be either ̶ MData0 ̶ MData0/Data1 ̶ MData0/Data1/Data2  If NB_TRANS = 2, the sequence should be either ̶ MData0 ̶ MData0/Data1  If NB_TRANS = 1, the sequence should be ̶ Data0 Isochronous Endpoint Handling: OUT Example The user can ascertain the bank status (free or busy), and the toggle sequencing of the data packet for each bank with the UDPHS_EPTSTAx register in the three bit fields as follows:  TOGGLESQ_STA: PID of the data stored in the current bank  CURRENT_BANK: Number of the bank currently being accessed by the microcontroller.  BUSY_BANK_STA: Number of busy bank This is particularly useful in case of a missing data packet. If the inter-packet delay between the OUT token and the Data is greater than the USB standard, then the ISO-OUT transaction is ignored. (Payload data is not written, no interrupt is generated to the CPU.) If there is a data CRC (Cyclic Redundancy Check) error, the payload is, none the less, written in the endpoint. The ERR_CRISO flag is set in UDPHS_EPTSTAx register. If the endpoint is already full, the packet is not written in the DPRAM. The ERR_FL_ISO flag is set in UDPHS_EPTSTAx. If the payload data is greater than the maximum size of the endpoint, then the ERR_OVFLW flag is set. It is the task of the CPU to manage this error. The data packet is written in the endpoint (except the extra data). 926 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

If the host sends a Zero Length Packet, and the endpoint is free, no data is written in the endpoint, the RX_BK_RDY flag is set, and the BYTE_COUNT field in UDPHS_EPTSTAx register is null. The FRCESTALL command bit is unused for an isochonous endpoint. Otherwise, payload data is written in the endpoint, the RX_BK_RDY interrupt is generated and the BYTE_COUNT in UDPHS_EPTSTAx register is updated. 39.5.8.5 STALL STALL is returned by a function in response to an IN token or after the data phase of an OUT or in response to a PING transaction. STALL indicates that a function is unable to transmit or receive data, or that a control pipe request is not supported.  OUT To stall an endpoint, set the FRCESTALL bit in UDPHS_EPTSETSTAx register and after the STALL_SNT flag has been set, set the TOGGLE_SEG bit in the UDPHS_EPTCLRSTAx register.  IN Set the FRCESTALL bit in UDPHS_EPTSETSTAx register. Figure 39-16. Stall Handshake Data OUT Transfer USB Bus Token OUT Data OUT Stall PID Packets FRCESTALL Set by Firmware Cleared by Firmware Interrupt Pending STALL_SNT Set by Hardware Cleared by Firmware Figure 39-17. Stall Handshake Data IN Transfer USB Bus Token IN Stall PID Packets FRCESTALL Cleared by Firmware Set by Firmware Interrupt Pending STALL_SNT Set by Hardware Cleared by Firmware 39.5.9 Speed Identification The high speed reset is managed by the hardware. At the connection, the host makes a reset which could be a classic reset (full speed) or a high speed reset. At the end of the reset process (full or high), the ENDRESET interrupt is generated. Then the CPU should read the SPEED bit in UDPHS_INTSTAx to ascertain the speed mode of the device. SAM9M11 [DATASHEET] 927 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.5.10USB V2.0 High Speed Global Interrupt Interrupts are defined in Section 39.6.3 ”UDPHS Interrupt Enable Register” (UDPHS_IEN) and in Section 39.6.4 ”UDPHS Interrupt Status Register” (UDPHS_INTSTA). 39.5.11 Endpoint Interrupts Interrupts are enabled in UDPHS_IEN (see Section 39.6.3 ”UDPHS Interrupt Enable Register”) and individually masked in UDPHS_EPTCTLENBx (see Section 39.6.9 ”UDPHS Endpoint Control Enable Register”). Table 39-4. Endpoint Interrupt Source Masks SHRT_PCKT Short Packet Interrupt BUSY_BANK Busy Bank Interrupt NAK_OUT NAKOUT Interrupt NAK_IN/ERR_FLUSH NAKIN/Error Flush Interrupt STALL_SNT/ERR_CRISO/ERR_NB_TRA Stall Sent/CRC error/Number of Transaction Error Interrupt RX_SETUP/ERR_FL_ISO Received SETUP/Error Flow Interrupt TX_PK_RD /ERR_TRANS TX Packet Read/Transaction Error Interrupt TX_COMPLT Transmitted IN Data Complete Interrupt RX_BK_RDY Received OUT Data Interrupt ERR_OVFLW Overflow Error Interrupt MDATA_RX MDATA Interrupt DATAX_RX DATAx Interrupt 928 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 39-18. UDPHS Interrupt Control Interface (UDPHS_IEN) Global IT mask DET_SUSPD Global IT sources MICRO_SOF INT_SOF USB Global IT Sources ENDRESET WAKE_UP ENDOFRSM UPSTR_RES (UDPHS_EPTCTLENBx) SHRT_PCKT EP mask (UDPHS_IEN) BUSY_BANK EPT_0 EP sources NAK_OUT husb2dev NAK_IN/ERR_FLUSH interrupt STALL_SNT/ERR_CRISO/ERR_NBTRA EPT0 IT RX_SETUP/ERR_FL_ISO Sources TX_BK_RDY/ERR_TRANS TX_COMPLT RX_BK_RDY ERR_OVFLW MDATA_RX DATAX_RX EP mask (UDPHS_IEN) EPT_x EP sources EPT1-6 IT (UDPHS_EPTCTLx) Sources INTDIS_DMA disable DMA channelx request mask (UDPHS_DMACONTROLx) (UDPHS_IEN) EN_BUFFIT DMA_x mask DMA CH x END_TR_IT mask DESC_LD_IT SAM9M11 [DATASHEET] 929 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.5.12Power Modes 39.5.12.1 Controlling Device States A USB device has several possible states. Refer to Chapter 9 (USB Device Framework) of the Universal Serial Bus Specification, Rev 2.0. Figure 39-19. UDPHS Device State Diagram Attached Hub Reset Hub or Configured Deconfigured Bus Inactive Powered Suspended Bus Activity Power Interruption Reset Bus Inactive Suspended Default Bus Activity Reset Address Assigned Bus Inactive Address Suspended Bus Activity Device Device Deconfigured Configured Bus Inactive Configured Suspended Bus Activity Movement from one state to another depends on the USB bus state or on standard requests sent through control transactions via the default endpoint (endpoint 0). After a period of bus inactivity, the USB device enters Suspend Mode. Accepting Suspend/Resume requests from the USB host is mandatory. Constraints in Suspend Mode are very strict for bus-powered applications; devices may not consume more than 500 µA on the USB bus. While in Suspend Mode, the host may wake up a device by sending a resume signal (bus activity) or a USB device may send a wake-up request to the host, e.g., waking up a PC by moving a USB mouse. The wake-up feature is not mandatory for all devices and must be negotiated with the host. 930 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.5.12.2 Not Powered State Self powered devices can detect 5V VBUS using a PIO. When the device is not connected to a host, device power consumption can be reduced by the DETACH bit in UDPHS_CTRL. Disabling the transceiver is automatically done. HSDM, HSDP, FSDP and FSDP lines are tied to GND pull-downs integrated in the hub downstream ports. 39.5.12.3 Entering Attached State When no device is connected, the USB FSDP and FSDM signals are tied to GND by 15 KΩ pull-downs integrated in the hub downstream ports. When a device is attached to a hub downstream port, the device connects a 1.5 KΩ pull-up on FSDP. The USB bus line goes into IDLE state, FSDP is pulled-up by the device 1.5 KΩ resistor to 3.3V and FSDM is pulled-down by the 15 KΩ resistor to GND of the host. After pull-up connection, the device enters the powered state. The transceiver remains disabled until bus activity is detected. In case of low power consumption need, the device can be stopped. When the device detects the VBUS, the software must enable the USB transceiver by enabling the EN_UDPHS bit in UDPHS_CTRL register. The software can detach the pull-up by setting DETACH bit in UDPHS_CTRL register. 39.5.12.4 From Powered State to Default State (Reset) After its connection to a USB host, the USB device waits for an end-of-bus reset. The unmasked flag ENDRESET is set in the UDPHS_IEN register and an interrupt is triggered. Once the ENDRESET interrupt has been triggered, the device enters Default State. In this state, the UDPHS software must:  Enable the default endpoint, setting the EPT_ENABL flag in the UDPHS_EPTCTLENB[0] register and, optionally, enabling the interrupt for endpoint 0 by writing 1 in EPT_0 of the UDPHS_IEN register. The enumeration then begins by a control transfer.  Configure the Interrupt Mask Register which has been reset by the USB reset detection  Enable the transceiver. In this state, the EN_UDPHS bit in UDPHS_CTRL register must be enabled. 39.5.12.5 From Default State to Address State (Address Assigned) After a Set Address standard device request, the USB host peripheral enters the address state. Warning: before the device enters address state, it must achieve the Status IN transaction of the control transfer, i.e., the UDPHS device sets its new address once the TX_COMPLT flag in the UDPHS_EPTCTL[0] register has been received and cleared. To move to address state, the driver software sets the DEV_ADDR field and the FADDR_EN flag in the UDPHS_CTRL register. 39.5.12.6 From Address State to Configured State (Device Configured) Once a valid Set Configuration standard request has been received and acknowledged, the device enables endpoints corresponding to the current configuration. This is done by setting the BK_NUMBER, EPT_TYPE, EPT_DIR and EPT_SIZE fields in the UDPHS_EPTCFGx registers and enabling them by setting the EPT_ENABL flag in the UDPHS_EPTCTLENBx registers, and, optionally, enabling corresponding interrupts in the UDPHS_IEN register. 39.5.12.7 Entering Suspend State (Bus Activity) When a Suspend (no bus activity on the USB bus) is detected, the DET_SUSPD signal in the UDPHS_STA register is set. This triggers an interrupt if the corresponding bit is set in the UDPHS_IEN register. This flag is cleared by writing to the UDPHS_CLRINT register. Then the device enters Suspend Mode. SAM9M11 [DATASHEET] 931 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

In this state bus powered devices must drain less than 500 µA from the 5V VBUS. As an example, the microcontroller switches to slow clock, disables the PLL and main oscillator, and goes into Idle Mode. It may also switch off other devices on the board. The UDPHS device peripheral clocks can be switched off. Resume event is asynchronously detected. 39.5.12.8 Receiving a Host Resume In Suspend mode, a resume event on the USB bus line is detected asynchronously, transceiver and clocks disabled (however the pull-up should not be removed). Once the resume is detected on the bus, the signal WAKE_UP in the UDPHS_INTSTA is set. It may generate an interrupt if the corresponding bit in the UDPHS_IEN register is set. This interrupt may be used to wake-up the core, enable PLL and main oscillators and configure clocks. 39.5.12.9 Sending an External Resume In Suspend State it is possible to wake-up the host by sending an external resume. The device waits at least 5 ms after being entered in Suspend State before sending an external resume. The device must force a K state from 1 to 15 ms to resume the host. 39.5.13Test Mode A device must support the TEST_MODE feature when in the Default, Address or Configured High Speed device states. TEST_MODE can be:  Test_J  Test_K  Test_Packet  Test_SEO_NAK (See Section 39.6.7 “UDPHS Test Register” on page 944 for definitions of each test mode.) const char test_packet_buffer[] = { 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // JKJKJKJK * 9 0xAA,0xAA,0xAA,0xAA,0xAA,0xAA,0xAA,0xAA, // JJKKJJKK * 8 0xEE,0xEE,0xEE,0xEE,0xEE,0xEE,0xEE,0xEE, // JJKKJJKK * 8 0xFE,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF, // JJJJJJJKKKKKKK * 8 0x7F,0xBF,0xDF,0xEF,0xF7,0xFB,0xFD, // JJJJJJJK * 8 0xFC,0x7E,0xBF,0xDF,0xEF,0xF7,0xFB,0xFD,0x7E // {JKKKKKKK * 10}, JK }; 932 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6 USB High Speed Device Port (UDPHS) User Interface Table 39-5. Register Mapping Offset Register Name Access Reset 0x00 UDPHS Control Register UDPHS_CTRL Read/Write 0x0000_0200 0x04 UDPHS Frame Number Register UDPHS_FNUM Read-only 0x0000_0000 0x08–0x0C Reserved – – – 0x10 UDPHS Interrupt Enable Register UDPHS_IEN Read/Write 0x0000_0010 0x14 UDPHS Interrupt Status Register UDPHS_INTSTA Read-only 0x0000_0000 0x18 UDPHS Clear Interrupt Register UDPHS_CLRINT Write-only – 0x1C UDPHS Endpoints Reset Register UDPHS_EPTRST Write-only – 0x20–0xCC Reserved – – – 0xE0 UDPHS Test Register UDPHS_TST Read/Write 0x0000_0000 0xE4–0xF8 Reserved – – – 0x100 + endpoint * 0x20 + 0x00 UDPHS Endpoint Configuration Register UDPHS_EPTCFG Read/Write 0x0000_0000 UDPHS Endpoint Control Enable 0x100 + endpoint * 0x20 + 0x04 UDPHS_EPTCTLENB Write-only – Register UDPHS Endpoint Control Disable 0x100 + endpoint * 0x20 + 0x08 UDPHS_EPTCTLDIS Write-only – Register 0x100 + endpoint * 0x20 + 0x0C UDPHS Endpoint Control Register UDPHS_EPTCTL Read-only 0x0000_0000(1) 0x100 + endpoint * 0x20 + 0x10 Reserved (for endpoint) – – – 0x100 + endpoint * 0x20 + 0x14 UDPHS Endpoint Set Status Register UDPHS_EPTSETSTA Write-only – 0x100 + endpoint * 0x20 + 0x18 UDPHS Endpoint Clear Status Register UDPHS_EPTCLRSTA Write-only – 0x100 + endpoint * 0x20 + 0x1C UDPHS Endpoint Status Register UDPHS_EPTSTA Read-only 0x0000_0040 0x120–0x1DC UDPHS Endpoint1 to 6 (2) Registers 0x1E0–0x300 Reserved – – – 0x300–0x30C Reserved – – – UDPHS DMA Next Descriptor Address 0x310 + channel * 0x10 + 0x00 UDPHS_DMANXTDSC Read/Write 0x0000_0000 Register 0x310 + channel * 0x10 + 0x04 UDPHS DMA Channel Address Register UDPHS_DMAADDRESS Read/Write 0x0000_0000 0x310 + channel * 0x10 + 0x08 UDPHS DMA Channel Control Register UDPHS_DMACONTROL Read/Write 0x0000_0000 0x310 + channel * 0x10 + 0x0C UDPHS DMA Channel Status Register UDPHS_DMASTATUS Read/Write 0x0000_0000 0x320–0x370 DMA Channel2 to 5 (3) Registers Notes: 1. The reset value for UDPHS_EPTCTL0 is 0x0000_0001. 2. The addresses for the UDPHS Endpoint registers shown here are for UDPHS Endpoint0. The structure of this group of registers is repeated successively for each endpoint according to the consecution of endpoint registers located between 0x120 and 0x1DC. 3. The addresses for the UDPHS DMA registers shown here are for UDPHS DMA Channel1. (There is no Channel0) The structure of this group of registers is repeated successively for each DMA channel according to the consecution of DMA registers located between 0x320 and 0x370. SAM9M11 [DATASHEET] 933 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.1 UDPHS Control Register Name: UDPHS_CTRL Address: 0xFFF78000 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – PULLD_DIS REWAKEUP DETACH EN_UDPHS 7 6 5 4 3 2 1 0 FADDR_EN DEV_ADDR • DEV_ADDR: UDPHS Address Read: This field contains the default address (0) after power-up or UDPHS bus reset. Write: This field is written with the value set by a SET_ADDRESS request received by the device firmware. • FADDR_EN: Function Address Enable Read: 0: Device is not in address state. 1: Device is in address state. Write: 0: Only the default function address is used (0). 1: This bit is set by the device firmware after a successful status phase of a SET_ADDRESS transaction. When set, the only address accepted by the UDPHS controller is the one stored in the UDPHS Address field. It will not be cleared after- wards by the device firmware. It is cleared by hardware on hardware reset, or when UDPHS bus reset is received (see above). • EN_UDPHS: UDPHS Enable Read: 0: UDPHS is disabled. 1: UDPHS is enabled. Write: 0: Disable and reset the UDPHS controller. Switch the host to UTMI. 1: Enables the UDPHS controller. Switch the host to UTMI. 934 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DETACH: Detach Command Read: 0: UDPHS is attached. 1: UDPHS is detached, UTMI transceiver is suspended. Write: 0: Pull up the DP line (attach command). 1: Simulate a detach on the UDPHS line and force the UTMI transceiver into suspend state (Suspend M = 0). (See PULLD_DIS description below.) • REWAKEUP: Send Remote Wake Up Read: 0: Remote Wake Up is disabled. 1: Remote Wake Up is enabled. Write: 0: No effect. 1: Force an external interrupt on the UDPHS controller for Remote Wake UP purposes. An Upstream Resume is sent only after the UDPHS bus has been in SUSPEND state for at least 5 ms. This bit is automatically cleared by hardware at the end of the Upstream Resume. • PULLD_DIS: Pull-down Disable When set, there is no pull-down on DP & DM. (DM Pull-Down = DP Pull-Down = 0). Note: If the DETACH bit is also set, device DP & DM are left in high impedance state. (See DETACH description above.) DETACH PULLD_DIS DP DM Condition 0 0 Pull up Pull down not recommended 0 1 Pull up High impedance state VBUS present 1 0 Pull down Pull down No VBUS 1 1 High impedance state High impedance state VBUS present & software disconnect SAM9M11 [DATASHEET] 935 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.2 UDPHS Frame Number Register Name: UDPHS_FNUM Address: 0xFFF78004 Access: Read 31 30 29 28 27 26 25 24 FNUM_ERR – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – FRAME_NUMBER 7 6 5 4 3 2 1 0 FRAME_NUMBER MICRO_FRAME_NUM • MICRO_FRAME_NUM: Microframe Number Number of the received microframe (0 to 7) in one frame.This field is reset at the beginning of each new frame (1 ms). One microframe is received each 125 microseconds (1 ms/8). • FRAME_NUMBER: Frame Number as defined in the Packet Field Formats This field is provided in the last received SOF packet (see INT_SOF in the UDPHS Interrupt Status Register). • FNUM_ERR: Frame Number CRC Error This bit is set by hardware when a corrupted Frame Number in Start of Frame packet (or Micro SOF) is received. This bit and the INT_SOF (or MICRO_SOF) interrupt are updated at the same time. 936 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.3 UDPHS Interrupt Enable Register Name: UDPHS_IEN Address: 0xFFF78010 Access: Read/Write 31 30 29 28 27 26 25 24 – DMA_6 DMA_5 DMA_4 DMA_3 DMA_2 DMA_1 – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – EPT_6 EPT_5 EPT_4 EPT_3 EPT_2 EPT_1 EPT_0 7 6 5 4 3 2 1 0 UPSTR_RES ENDOFRSM WAKE_UP ENDRESET INT_SOF MICRO_SOF DET_SUSPD – • DET_SUSPD: Suspend Interrupt Enable Read: 0: Suspend Interrupt is disabled. 1: Suspend Interrupt is enabled. Write: 0: Disable Suspend Interrupt. 1: Enable Suspend Interrupt. • MICRO_SOF: Micro-SOF Interrupt Enable Read: 0: Micro-SOF Interrupt is disabled. 1: Micro-SOF Interrupt is enabled. Write: 0: Disable Micro-SOF Interrupt. 1: Enable Micro-SOF Interrupt. • INT_SOF: SOF Interrupt Enable Read: 0: SOF Interrupt is disabled. 1: SOF Interrupt is enabled. Write: 0: Disable SOF Interrupt. 1: Enable SOF Interrupt. SAM9M11 [DATASHEET] 937 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• ENDRESET: End Of Reset Interrupt Enable Read: 0: End Of Reset Interrupt is disabled. 1: End Of Reset Interrupt is enabled. Write: 0: Disable End Of Reset Interrupt. 1: Enable End Of Reset Interrupt. Automatically enabled after USB reset. • WAKE_UP: Wake Up CPU Interrupt Enable Read: 0: Wake Up CPU Interrupt is disabled. 1: Wake Up CPU Interrupt is enabled. Write 0: Disable Wake Up CPU Interrupt. 1: Enable Wake Up CPU Interrupt. • ENDOFRSM: End Of Resume Interrupt Enable Read: 0: Resume Interrupt is disabled. 1: Resume Interrupt is enabled. Write: 0: Disable Resume Interrupt. 1: Enable Resume Interrupt. • UPSTR_RES: Upstream Resume Interrupt Enable Read: 0: Upstream Resume Interrupt is disabled. 1: Upstream Resume Interrupt is enabled. Write: 0: Disable Upstream Resume Interrupt. 1: Enable Upstream Resume Interrupt. • EPT_x: Endpoint x Interrupt Enable Read: 0: The interrupts for this endpoint are disabled. 1: The interrupts for this endpoint are enabled. Write: 0: Disable the interrupts for this endpoint. 1: Enable the interrupts for this endpoint. 938 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DMA_x: DMA Channel x Interrupt Enable Read: 0: The interrupts for this channel are disabled. 1: The interrupts for this channel are enabled. Write: 0: Disable the interrupts for this channel. 1: Enable the interrupts for this channel. SAM9M11 [DATASHEET] 939 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.4 UDPHS Interrupt Status Register Name: UDPHS_INTSTA Address: 0xFFF78014 Access: Read-only 31 30 29 28 27 26 25 24 – DMA_6 DMA_5 DMA_4 DMA_3 DMA_2 DMA_1 – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – EPT_6 EPT_5 EPT_4 EPT_3 EPT_2 EPT_1 EPT_0 7 6 5 4 3 2 1 0 UPSTR_RES ENDOFRSM WAKE_UP ENDRESET INT_SOF MICRO_SOF DET_SUSPD SPEED • SPEED: Speed Status 0: Reset by hardware when the hardware is in Full Speed mode. 1: Set by hardware when the hardware is in High Speed mode • DET_SUSPD: Suspend Interrupt 0: Cleared by setting the DET_SUSPD bit in UDPHS_CLRINT register 1: Set by hardware when a UDPHS Suspend (Idle bus for three frame periods, a J state for 3 ms) is detected. This triggers a UDPHS interrupt when the DET_SUSPD bit is set in UDPHS_IEN register. • MICRO_SOF: Micro Start Of Frame Interrupt 0: Cleared by setting the MICRO_SOF bit in UDPHS_CLRINT register. 1: Set by hardware when an UDPHS micro start of frame PID (SOF) has been detected (every 125 µs) or synthesized by the macro. This triggers a UDPHS interrupt when the MICRO_SOF bit is set in UDPHS_IEN. In case of detected SOF, the MICRO_FRAME_NUM field in UDPHS_FNUM register is incremented and the FRAME_NUMBER field does not change. Note: The Micro Start Of Frame Interrupt (MICRO_SOF), and the Start Of Frame Interrupt (INT_SOF) are not generated at the same time. • INT_SOF: Start Of Frame Interrupt 0: Cleared by setting the INT_SOF bit in UDPHS_CLRINT. 1: Set by hardware when an UDPHS Start Of Frame PID (SOF) has been detected (every 1 ms) or synthesized by the macro. This triggers a UDPHS interrupt when the INT_SOF bit is set in UDPHS_IEN register. In case of detected SOF, in High Speed mode, the MICRO_FRAME_NUMBER field is cleared in UDPHS_FNUM register and the FRAME_NUMBER field is updated. • ENDRESET: End Of Reset Interrupt 0: Cleared by setting the ENDRESET bit in UDPHS_CLRINT. 1: Set by hardware when an End Of Reset has been detected by the UDPHS controller. This triggers a UDPHS interrupt when the ENDRESET bit is set in UDPHS_IEN. 940 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• WAKE_UP: Wake Up CPU Interrupt 0: Cleared by setting the WAKE_UP bit in UDPHS_CLRINT. 1: Set by hardware when the UDPHS controller is in SUSPEND state and is re-activated by a filtered non-idle signal from the UDPHS line (not by an upstream resume). This triggers a UDPHS interrupt when the WAKE_UP bit is set in UDPHS_IEN register. When receiving this interrupt, the user has to enable the device controller clock prior to operation. Note: this interrupt is generated even if the device controller clock is disabled. • ENDOFRSM: End Of Resume Interrupt 0: Cleared by setting the ENDOFRSM bit in UDPHS_CLRINT. 1: Set by hardware when the UDPHS controller detects a good end of resume signal initiated by the host. This triggers a UDPHS interrupt when the ENDOFRSM bit is set in UDPHS_IEN. • UPSTR_RES: Upstream Resume Interrupt 0: Cleared by setting the UPSTR_RES bit in UDPHS_CLRINT. 1: Set by hardware when the UDPHS controller is sending a resume signal called “upstream resume”. This triggers a UDPHS interrupt when the UPSTR_RES bit is set in UDPHS_IEN. • EPT_x: Endpoint x Interrupt 0: Reset when the UDPHS_EPTSTAx interrupt source is cleared. 1: Set by hardware when an interrupt is triggered by the UDPHS_EPTSTAx register and this endpoint interrupt is enabled by the EPT_x bit in UDPHS_IEN. • DMA_x: DMA Channel x Interrupt 0: Reset when the UDPHS_DMASTATUSx interrupt source is cleared. 1: Set by hardware when an interrupt is triggered by the DMA Channelx and this endpoint interrupt is enabled by the DMA_x bit in UDPHS_IEN. SAM9M11 [DATASHEET] 941 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.5 UDPHS Clear Interrupt Register Name: UDPHS_CLRINT Address: 0xFFF78018 Access: Write only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 UPSTR_RES ENDOFRSM WAKE_UP ENDRESET INT_SOF MICRO_SOF DET_SUSPD – • DET_SUSPD: Suspend Interrupt Clear 0: No effect. 1: Clear the DET_SUSPD bit in UDPHS_INTSTA. • MICRO_SOF: Micro Start Of Frame Interrupt Clear 0: No effect. 1: Clear the MICRO_SOF bit in UDPHS_INTSTA. • INT_SOF: Start Of Frame Interrupt Clear 0: No effect. 1: Clear the INT_SOF bit in UDPHS_INTSTA. • ENDRESET: End Of Reset Interrupt Clear 0: No effect. 1: Clear the ENDRESET bit in UDPHS_INTSTA. • WAKE_UP: Wake Up CPU Interrupt Clear 0: No effect. 1: Clear the WAKE_UP bit in UDPHS_INTSTA. • ENDOFRSM: End Of Resume Interrupt Clear 0: No effect. 1: Clear the ENDOFRSM bit in UDPHS_INTSTA. • UPSTR_RES: Upstream Resume Interrupt Clear 0: No effect. 1: Clear the UPSTR_RES bit in UDPHS_INTSTA. 942 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.6 UDPHS Endpoints Reset Register Name: UDPHS_EPTRST Address: 0xFFF7801C Access: Write only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – EPT_6 EPT_5 EPT_4 EPT_3 EPT_2 EPT_1 EPT_0 • EPT_x: Endpoint x Reset 0: No effect. 1: Reset the Endpointx state. Setting this bit clears the Endpoint status UDPHS_EPTSTAx register, except for the TOGGLESQ_STA field. SAM9M11 [DATASHEET] 943 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.7 UDPHS Test Register Name: UDPHS_TST Address: 0xFFF780E0 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – OPMODE2 TST_PKT TST_K TST_J SPEED_CFG • SPEED_CFG: Speed Configuration Read/Write: Speed Configuration: Normal Mode: The macro is in Full Speed mode, ready to make a High Speed identification, if the host supports it and then 00 to automatically switch to High Speed mode 01 Reserved 10 Force High Speed: Set this value to force the hardware to work in High Speed mode. Only for debug or test purpose. Force Full Speed: Set this value to force the hardware to work only in Full Speed mode. In this configuration, the macro will 11 not respond to a High Speed reset handshake • TST_J: Test J Mode Read and write: 0: No effect. 1: Set to send the J state on the UDPHS line. This enables the testing of the high output drive level on the D+ line. • TST_K: Test K Mode Read and write: 0: No effect. 1: Set to send the K state on the UDPHS line. This enables the testing of the high output drive level on the D- line. • TST_PKT: Test Packet Mode Read and write: 0: No effect. 1: Set to repetitively transmit the packet stored in the current bank. This enables the testing of rise and fall times, eye pat- terns, jitter, and any other dynamic waveform specifications. 944 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• OPMODE2: OpMode2 Read and write: 0: No effect. 1: Set to force the OpMode signal (UTMI interface) to “10”, to disable the bit-stuffing and the NRZI encoding. Note: For the Test mode, Test_SE0_NAK (see Universal Serial Bus Specification, Revision 2.0: 7.1.20, Test Mode Sup- port). Force the device in High Speed mode, and configure a bulk-type endpoint. Do not fill this endpoint for sending NAK to the host. Upon command, a port’s transceiver must enter the High Speed receive mode and remain in that mode until the exit action is taken. This enables the testing of output impedance, low level output voltage and loading characteristics. In addition, while in this mode, upstream facing ports (and only upstream facing ports) must respond to any IN token packet with a NAK handshake (only if the packet CRC is determined to be correct) within the normal allowed device response time. This enables testing of the device squelch level circuitry and, additionally, provides a general purpose stimulus/response test for basic functional testing. SAM9M11 [DATASHEET] 945 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.8 UDPHS Endpoint Configuration Register Name: UDPHS_EPTCFGx [x=0..6] Address: 0xFFF78100 [0], 0xFFF78120 [1], 0xFFF78140 [2], 0xFFF78160 [3], 0xFFF78180 [4], 0xFFF781A0 [5], 0xFFF781C0 [6] Access: Read/Write 31 30 29 28 27 26 25 24 EPT_MAPD – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – NB_TRANS 7 6 5 4 3 2 1 0 BK_NUMBER EPT_TYPE EPT_DIR EPT_SIZE • EPT_SIZE: Endpoint Size Read and write: Set this field according to the endpoint size in bytes (see Section 39.5.5 ”Endpoint Configuration”). Endpoint Size 000 8 bytes 001 16 bytes 010 32 bytes 011 64 bytes 100 128 bytes 101 256 bytes 110 512 bytes 111 1024 bytes(1) Note: 1. 1024 bytes is only for isochronous endpoint. • EPT_DIR: Endpoint Direction Read and write: 0: Clear this bit to configure OUT direction for Bulk, Interrupt and Isochronous endpoints. 1: Set this bit to configure IN direction for Bulk, Interrupt and Isochronous endpoints. For Control endpoints this bit has no effect and should be left at zero. 946 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• EPT_TYPE: Endpoint Type Read and write: Set this field according to the endpoint type (see Section 39.5.5 ”Endpoint Configuration”). (Endpoint 0 should always be configured as control) :Endpoint Type 00 Control endpoint 01 Isochronous endpoint 10 Bulk endpoint 11 Interrupt endpoint • BK_NUMBER: Number of Banks Read and write: Set this field according to the endpoint’s number of banks (see Section 39.5.5 ”Endpoint Configuration”). Number of Banks 00 Zero bank, the endpoint is not mapped in memory 01 One bank (bank 0) 10 Double bank (Ping-Pong: bank 0/bank 1) 11 Triple bank (bank 0/bank 1/bank 2) • NB_TRANS: Number Of Transaction per Microframe Read and Write: The Number of transactions per microframe is set by software. Note: Meaningful for high bandwidth isochronous endpoint only. • EPT_MAPD: Endpoint Mapped Read-only: 0: The user should reprogram the register with correct values. 1: Set by hardware when the endpoint size (EPT_SIZE) and the number of banks (BK_NUMBER) are correct regarding: – the fifo max capacity (FIFO_MAX_SIZE in UDPHS_IPFEATURES register) – the number of endpoints/banks already allocated – the number of allowed banks for this endpoint SAM9M11 [DATASHEET] 947 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.9 UDPHS Endpoint Control Enable Register Name: UDPHS_EPTCTLENBx [x=0..6] Address: 0xFFF78104 [0], 0xFFF78124 [1], 0xFFF78144 [2], 0xFFF78164 [3], 0xFFF78184 [4], 0xFFF781A4 [5], 0xFFF781C4 [6] Access: Write-only 31 30 29 28 27 26 25 24 SHRT_PCKT – – – – – – – 23 22 21 20 19 18 17 16 – – – – – BUSY_BANK – – 15 14 13 12 11 10 9 8 STALL_SNT/ NAK_IN/ RX_SETUP/ TX_PK_RDY/ NAK_OUT ERR_CRISO/ TX_COMPLT RX_BK_RDY ERR_OVFLW ERR_FLUSH ERR_FL_ISO ERR_TRANS ERR_NBTRA 7 6 5 4 3 2 1 0 MDATA_RX DATAX_RX – NYET_DIS INTDIS_DMA – AUTO_VALID EPT_ENABL For additional Information, see “UDPHS Endpoint Control Register” on page 952. • EPT_ENABL: Endpoint Enable 0: No effect. 1: Enable endpoint according to the device configuration. • AUTO_VALID: Packet Auto-Valid Enable 0: No effect. 1: Enable this bit to automatically validate the current packet and switch to the next bank for both IN and OUT transfers. • INTDIS_DMA: Interrupts Disable DMA 0: No effect. 1: If set, when an enabled endpoint-originated interrupt is triggered, the DMA request is disabled. • NYET_DIS: NYET Disable (Only for High Speed Bulk OUT endpoints) 0: No effect. 1: Forces an ACK response to the next High Speed Bulk OUT transfer instead of a NYET response. • DATAX_RX: DATAx Interrupt Enable (Only for high bandwidth Isochronous OUT endpoints) 0: No effect. 1: Enable DATAx Interrupt. • MDATA_RX: MDATA Interrupt Enable (Only for high bandwidth Isochronous OUT endpoints) 0: No effect. 1: Enable MDATA Interrupt. 948 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• ERR_OVFLW: Overflow Error Interrupt Enable 0: No effect. 1: Enable Overflow Error Interrupt. • RX_BK_RDY: Received OUT Data Interrupt Enable 0: No effect. 1: Enable Received OUT Data Interrupt. • TX_COMPLT: Transmitted IN Data Complete Interrupt Enable 0: No effect. 1: Enable Transmitted IN Data Complete Interrupt. • TX_PK_RDY/ERR_TRANS: TX Packet Ready/Transaction Error Interrupt Enable 0: No effect. 1: Enable TX Packet Ready/Transaction Error Interrupt. • RX_SETUP/ERR_FL_ISO: Received SETUP/Error Flow Interrupt Enable 0: No effect. 1: Enable RX_SETUP/Error Flow ISO Interrupt. • STALL_SNT/ERR_CRISO/ERR_NBTRA: Stall Sent /ISO CRC Error/Number of Transaction Error Interrupt Enable 0: No effect. 1: Enable Stall Sent/Error CRC ISO/Error Number of Transaction Interrupt. • NAK_IN/ERR_FLUSH: NAKIN/Bank Flush Error Interrupt Enable 0: No effect. 1: Enable NAKIN/Bank Flush Error Interrupt. • NAK_OUT: NAKOUT Interrupt Enable 0: No effect. 1: Enable NAKOUT Interrupt. • BUSY_BANK: Busy Bank Interrupt Enable 0: No effect. 1: Enable Busy Bank Interrupt. • SHRT_PCKT: Short Packet Send/Short Packet Interrupt Enable For OUT endpoints: 0: No effect. 1: Enable Short Packet Interrupt. For IN endpoints: Guarantees short packet at end of DMA Transfer if the UDPHS_DMACONTROLx register END_B_EN and UDPHS_EPTCTLx register AUTOVALID bits are also set. SAM9M11 [DATASHEET] 949 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.10UDPHS Endpoint Control Disable Register Name: UDPHS_EPTCTLDISx [x=0..6] Address: 0xFFF78108 [0], 0xFFF78128 [1], 0xFFF78148 [2], 0xFFF78168 [3], 0xFFF78188 [4], 0xFFF781A8 [5], 0xFFF781C8 [6] Access: Write-only 31 30 29 28 27 26 25 24 SHRT_PCKT – – – – – – – 23 22 21 20 19 18 17 16 – – – – – BUSY_BANK – – 15 14 13 12 11 10 9 8 STALL_SNT/ NAK_IN/ RX_SETUP/ TX_PK_RDY/ NAK_OUT ERR_CRISO/ TX_COMPLT RX_BK_RDY ERR_OVFLW ERR_FLUSH ERR_FL_ISO ERR_TRANS ERR_NBTRA 7 6 5 4 3 2 1 0 MDATA_RX DATAX_RX – NYET_DIS INTDIS_DMA – AUTO_VALID EPT_DISABL For additional Information, see “UDPHS Endpoint Control Register” on page 952. • EPT_DISABL: Endpoint Disable 0: No effect. 1: Disable endpoint. • AUTO_VALID: Packet Auto-Valid Disable 0: No effect. 1: Disable this bit to not automatically validate the current packet. • INTDIS_DMA: Interrupts Disable DMA 0: No effect. 1: Disable the “Interrupts Disable DMA”. • NYET_DIS: NYET Enable (Only for High Speed Bulk OUT endpoints) 0: No effect. 1: Let the hardware handle the handshake response for the High Speed Bulk OUT transfer. • DATAX_RX: DATAx Interrupt Disable (Only for High Bandwidth Isochronous OUT endpoints) 0: No effect. 1: Disable DATAx Interrupt. • MDATA_RX: MDATA Interrupt Disable (Only for High Bandwidth Isochronous OUT endpoints) 0: No effect. 1: Disable MDATA Interrupt. 950 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• ERR_OVFLW: Overflow Error Interrupt Disable 0: No effect. 1: Disable Overflow Error Interrupt. • RX_BK_RDY: Received OUT Data Interrupt Disable 0: No effect. 1: Disable Received OUT Data Interrupt. • TX_COMPLT: Transmitted IN Data Complete Interrupt Disable 0: No effect. 1: Disable Transmitted IN Data Complete Interrupt. • TX_PK_RDY/ERR_TRANS: TX Packet Ready/Transaction Error Interrupt Disable 0: No effect. 1: Disable TX Packet Ready/Transaction Error Interrupt. • RX_SETUP/ERR_FL_ISO: Received SETUP/Error Flow Interrupt Disable 0: No effect. 1: Disable RX_SETUP/Error Flow ISO Interrupt. • STALL_SNT/ERR_CRISO/ERR_NBTRA: Stall Sent/ISO CRC Error/Number of Transaction Error Interrupt Disable 0: No effect. 1: Disable Stall Sent/Error CRC ISO/Error Number of Transaction Interrupt. • NAK_IN/ERR_FLUSH: NAKIN/bank flush error Interrupt Disable 0: No effect. 1: Disable NAKIN/Bank Flush Error Interrupt. • NAK_OUT: NAKOUT Interrupt Disable 0: No effect. 1: Disable NAKOUT Interrupt. • BUSY_BANK: Busy Bank Interrupt Disable 0: No effect. 1: Disable Busy Bank Interrupt. • SHRT_PCKT: Short Packet Interrupt Disable For OUT endpoints: 0: No effect. 1: Disable Short Packet Interrupt. For IN endpoints: Never automatically add a zero length packet at end of DMA transfer. SAM9M11 [DATASHEET] 951 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.11 UDPHS Endpoint Control Register Name: UDPHS_EPTCTLx [x=0..6] Address: 0xFFF7810C [0], 0xFFF7812C [1], 0xFFF7814C [2], 0xFFF7816C [3], 0xFFF7818C [4], 0xFFF781AC [5], 0xFFF781CC [6] Access: Read-only 31 30 29 28 27 26 25 24 SHRT_PCKT – – – – – – – 23 22 21 20 19 18 17 16 – – – – – BUSY_BANK – – 15 14 13 12 11 10 9 8 STALL_SNT/ NAK_IN/ RX_SETUP/ TX_PK_RDY/ NAK_OUT ERR_CRISO/ TX_COMPLT RX_BK_RDY ERR_OVFLW ERR_FLUSH ERR_FL_ISO ERR_TRANS ERR_NBTRA 7 6 5 4 3 2 1 0 MDATA_RX DATAX_RX – NYET_DIS INTDIS_DMA – AUTO_VALID EPT_ENABL • EPT_ENABL: Endpoint Enable 0: If cleared, the endpoint is disabled according to the device configuration. Endpoint 0 should always be enabled after a hardware or UDPHS bus reset and participate in the device configuration. 1: If set, the endpoint is enabled according to the device configuration. • AUTO_VALID: Packet Auto-Valid Enabled (Not for CONTROL Endpoints) Set this bit to automatically validate the current packet and switch to the next bank for both IN and OUT endpoints. For IN Transfer: If this bit is set, then the UDPHS_EPTSTAx register TX_PK_RDY bit is set automatically when the current bank is full and at the end of DMA buffer if the UDPHS_DMACONTROLx register END_B_EN bit is set. The user may still set the UDPHS_EPTSTAx register TX_PK_RDY bit if the current bank is not full, unless the user wants to send a Zero Length Packet by software. For OUT Transfer: If this bit is set, then the UDPHS_EPTSTAx register RX_BK_RDY bit is automatically reset for the current bank when the last packet byte has been read from the bank FIFO or at the end of DMA buffer if the UDPHS_DMACONTROLx register END_B_EN bit is set. For example, to truncate a padded data packet when the actual data transfer size is reached. The user may still clear the UDPHS_EPTSTAx register RX_BK_RDY bit, for example, after completing a DMA buffer by software if UDPHS_DMACONTROLx register END_B_EN bit was disabled or in order to cancel the read of the remaining data bank(s). • INTDIS_DMA: Interrupt Disables DMA If set, when an enabled endpoint-originated interrupt is triggered, the DMA request is disabled regardless of the UDPHS_IEN register EPT_x bit for this endpoint. Then, the firmware will have to clear or disable the interrupt source or clear this bit if transfer completion is needed. If the exception raised is associated with the new system bank packet, then the previous DMA packet transfer is normally completed, but the new DMA packet transfer is not started (not requested). 952 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

If the exception raised is not associated to a new system bank packet (NAK_IN, NAK_OUT, ERR_FL_ISO...), then the request cancellation may happen at any time and may immediately stop the current DMA transfer. This may be used, for example, to identify or prevent an erroneous packet to be transferred into a buffer or to complete a DMA buffer by software after reception of a short packet, or to perform buffer truncation on ERR_FL_ISO interrupt for adaptive rate. • NYET_DIS: NYET Disable (Only for High Speed Bulk OUT endpoints) 0: If clear, this bit lets the hardware handle the handshake response for the High Speed Bulk OUT transfer. 1: If set, this bit forces an ACK response to the next High Speed Bulk OUT transfer instead of a NYET response. Note: According to the Universal Serial Bus Specification, Rev 2.0 (8.5.1.1 NAK Responses to OUT/DATA During PING Protocol), a NAK response to an HS Bulk OUT transfer is expected to be an unusual occurrence. • DATAX_RX: DATAx Interrupt Enabled (Only for High Bandwidth Isochronous OUT endpoints) 0: No effect. 1: Send an interrupt when a DATA2, DATA1 or DATA0 packet has been received meaning the whole microframe data pay- load has been received. • MDATA_RX: MDATA Interrupt Enabled (Only for High Bandwidth Isochronous OUT endpoints) 0: No effect. 1: Send an interrupt when an MDATA packet has been received and so at least one packet of the microframe data payload has been received. • ERR_OVFLW: Overflow Error Interrupt Enabled 0: Overflow Error Interrupt is masked. 1: Overflow Error Interrupt is enabled. • RX_BK_RDY: Received OUT Data Interrupt Enabled 0: Received OUT Data Interrupt is masked. 1: Received OUT Data Interrupt is enabled. • TX_COMPLT: Transmitted IN Data Complete Interrupt Enabled 0: Transmitted IN Data Complete Interrupt is masked. 1: Transmitted IN Data Complete Interrupt is enabled. • TX_PK_RDY/ERR_TRANS: TX Packet Ready/Transaction Error Interrupt Enabled 0: TX Packet Ready/Transaction Error Interrupt is masked. 1: TX Packet Ready/Transaction Error Interrupt is enabled. Caution: Interrupt source is active as long as the corresponding UDPHS_EPTSTAx register TX_PK_RDY flag remains low. If there are no more banks available for transmitting after the software has set UDPHS_EPTSTAx/TX_PK_RDY for the last transmit packet, then the interrupt source remains inactive until the first bank becomes free again to transmit at UDPHS_EPTSTAx/TX_PK_RDY hardware clear. • RX_SETUP/ERR_FL_ISO: Received SETUP/Error Flow Interrupt Enabled 0: Received SETUP/Error Flow Interrupt is masked. 1: Received SETUP/Error Flow Interrupt is enabled. SAM9M11 [DATASHEET] 953 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• STALL_SNT/ERR_CRISO/ERR_NBTRA: Stall Sent/ISO CRC Error/Number of Transaction Error Interrupt Enabled 0: Stall Sent/ISO CRC error/number of Transaction Error Interrupt is masked. 1: Stall Sent /ISO CRC error/number of Transaction Error Interrupt is enabled. • NAK_IN/ERR_FLUSH: NAKIN/Bank Flush Error Interrupt Enabled 0: NAKIN Interrupt is masked. 1: NAKIN/Bank Flush Error Interrupt is enabled. • NAK_OUT: NAKOUT Interrupt Enabled 0: NAKOUT Interrupt is masked. 1: NAKOUT Interrupt is enabled. • BUSY_BANK: Busy Bank Interrupt Enabled 0: BUSY_BANK Interrupt is masked. 1: BUSY_BANK Interrupt is enabled. For OUT endpoints: an interrupt is sent when all banks are busy. For IN endpoints: an interrupt is sent when all banks are free. • SHRT_PCKT: Short Packet Interrupt Enabled For OUT endpoints: send an Interrupt when a Short Packet has been received. 0: Short Packet Interrupt is masked. 1: Short Packet Interrupt is enabled. For IN endpoints: a Short Packet transmission is guaranteed upon end of the DMA Transfer, thus signaling a BULK or INTERRUPT end of transfer or an end of isochronous (micro-)frame data, but only if the UDPHS_DMACONTROLx register END_B_EN and UDPHS_EPTCTLx register AUTO_VALID bits are also set. 954 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.12UDPHS Endpoint Set Status Register Name: UDPHS_EPTSETSTAx [x=0..6] Address: 0xFFF78114 [0], 0xFFF78134 [1], 0xFFF78154 [2], 0xFFF78174 [3], 0xFFF78194 [4], 0xFFF781B4 [5], 0xFFF781D4 [6] Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – TX_PK_RDY – KILL_BANK – 7 6 5 4 3 2 1 0 – – FRCESTALL – – – – – • FRCESTALL: Stall Handshake Request Set 0: No effect. 1: Set this bit to request a STALL answer to the host for the next handshake Refer to chapters 8.4.5 (Handshake Packets) and 9.4.5 (Get Status) of the Universal Serial Bus Specification, Rev 2.0 for more information on the STALL handshake. • KILL_BANK: KILL Bank Set (for IN Endpoint) 0: No effect. 1: Kill the last written bank. • TX_PK_RDY: TX Packet Ready Set 0: No effect. 1: Set this bit after a packet has been written into the endpoint FIFO for IN data transfers – This flag is used to generate a Data IN transaction (device to host). – Device firmware checks that it can write a data payload in the FIFO, checking that TX_PK_RDY is cleared. – Transfer to the FIFO is done by writing in the “Buffer Address” register. – Once the data payload has been transferred to the FIFO, the firmware notifies the UDPHS device setting TX_PK_RDY to one. – UDPHS bus transactions can start. – TXCOMP is set once the data payload has been received by the host. – Data should be written into the endpoint FIFO only after this bit has been cleared. – Set this bit without writing data to the endpoint FIFO to send a Zero Length Packet. SAM9M11 [DATASHEET] 955 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.13UDPHS Endpoint Clear Status Register Name: UDPHS_EPTCLRSTAx [x=0..6] Address: 0xFFF78118 [0], 0xFFF78138 [1], 0xFFF78158 [2], 0xFFF78178 [3], 0xFFF78198 [4], 0xFFF781B8 [5], 0xFFF781D8 [6] Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 NAK_IN/ STALL_SNT/ RX_SETUP/ NAK_OUT – TX_COMPLT RX_BK_RDY – ERR_FLUSH ERR_NBTRA ERR_FL_ISO 7 6 5 4 3 2 1 0 – TOGGLESQ FRCESTALL – – – – – • FRCESTALL: Stall Handshake Request Clear 0: No effect. 1: Clear the STALL request. The next packets from host will not be STALLed. • TOGGLESQ: Data Toggle Clear 0: No effect. 1: Clear the PID data of the current bank For OUT endpoints, the next received packet should be a DATA0. For IN endpoints, the next packet will be sent with a DATA0 PID. • RX_BK_RDY: Received OUT Data Clear 0: No effect. 1: Clear the RX_BK_RDY flag of UDPHS_EPTSTAx. • TX_COMPLT: Transmitted IN Data Complete Clear 0: No effect. 1: Clear the TX_COMPLT flag of UDPHS_EPTSTAx. • RX_SETUP/ERR_FL_ISO: Received SETUP/Error Flow Clear 0: No effect. 1: Clear the RX_SETUP/ERR_FL_ISO flags of UDPHS_EPTSTAx. • STALL_SNT/ERR_NBTRA: Stall Sent/Number of Transaction Error Clear 0: No effect. 1: Clear the STALL_SNT/ERR_NBTRA flags of UDPHS_EPTSTAx. 956 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• NAK_IN/ERR_FLUSH: NAKIN/Bank Flush Error Clear 0: No effect. 1: Clear the NAK_IN/ERR_FLUSH flags of UDPHS_EPTSTAx. • NAK_OUT: NAKOUT Clear 0: No effect. 1: Clear the NAK_OUT flag of UDPHS_EPTSTAx. SAM9M11 [DATASHEET] 957 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.14UDPHS Endpoint Status Register Name: UDPHS_EPTSTAx [x=0..6] Address: 0xFFF7811C [0], 0xFFF7813C [1], 0xFFF7815C [2], 0xFFF7817C [3], 0xFFF7819C [4], 0xFFF781BC [5], 0xFFF781DC [6] Access: Read-only 31 30 29 28 27 26 25 24 SHRT_PCKT BYTE_COUNT 23 22 21 20 19 18 17 16 CURRENT_BANK/ BYTE_COUNT BUSY_BANK_STA CONTROL_DIR 15 14 13 12 11 10 9 8 STALL_SNT/ NAK_IN/ RX_SETUP/ TX_PK_RDY/ RX_BK_RDY/ NAK_OUT ERR_CRISO/ TX_COMPLT ERR_OVFLW ERR_FLUSH ERR_FL_ISO ERR_TRANS KILL_BANK ERR_NBTRA 7 6 5 4 3 2 1 0 TOGGLESQ_STA FRCESTALL – – – – – • FRCESTALL: Stall Handshake Request 0: No effect. 1: If set a STALL answer will be done to the host for the next handshake. This bit is reset by hardware upon received SETUP. • TOGGLESQ_STA: Toggle Sequencing Toggle Sequencing: – IN endpoint: It indicates the PID Data Toggle that will be used for the next packet sent. This is not relative to the current bank. – CONTROL and OUT endpoint: These bits are set by hardware to indicate the PID data of the current bank: 00 Data0 01 Data1 10 Data2 (only for High Bandwidth Isochronous Endpoint) 11 MData (only for High Bandwidth Isochronous Endpoint) Note 1: In OUT transfer, the Toggle information is meaningful only when the current bank is busy (Received OUT Data=1). Note 2: These bits are updated for OUT transfer: – A new data has been written into the current bank. – The user has just cleared the Received OUT Data bit to switch to the next bank. Note 3: For High Bandwidth Isochronous Out endpoint, it is recommended to check the UDPHS_EPTSTAx/ERR_TRANS bit to know if the toggle sequencing is correct or not. Note 4: This field is reset to DATA1 by the UDPHS_EPTCLRSTAx register TOGGLESQ bit, and by UDPHS_EPTCTLDISx (disable endpoint). 958 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• ERR_OVFLW: Overflow Error This bit is set by hardware when a new too-long packet is received. Example: If the user programs an endpoint 64 bytes wide and the host sends 128 bytes in an OUT transfer, then the Over- flow Error bit is set. This bit is updated at the same time as the BYTE_COUNT field. This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint) and by UDPHS_EPTCTLDISx (disable endpoint). • RX_BK_RDY/KILL_BANK: Received OUT Data/KILL Bank – Received OUT Data: (For OUT endpoint or Control endpoint) This bit is set by hardware after a new packet has been stored in the endpoint FIFO. This bit is cleared by the device firmware after reading the OUT data from the endpoint. For multi-bank endpoints, this bit may remain active even when cleared by the device firmware, this if an other packet has been received meanwhile. Hardware assertion of this bit may generate an interrupt if enabled by the UDPHS_EPTCTLx register RX_BK_RDY bit. This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint) and by UDPHS_EPTCTLDISx (disable endpoint). – KILL Bank: (For IN endpoint) – The bank is really cleared or the bank is sent, BUSY_BANK_STA is decremented. – The bank is not cleared but sent on the IN transfer, TX_COMPLT – The bank is not cleared because it was empty. The user should wait that this bit is cleared before trying to clear another packet. Note: “Kill a packet” may be refused if at the same time, an IN token is coming and the current packet is sent on the UDPHS line. In this case, the TX_COMPLT bit is set. Take notice however, that if at least two banks are ready to be sent, there is no problem to kill a packet even if an IN token is coming. In fact, in that case, the current bank is sent (IN transfer) and the last bank is killed. • TX_COMPLT: Transmitted IN Data Complete This bit is set by hardware after an IN packet has been transmitted for isochronous endpoints and after it has been accepted (ACK’ed) by the host for Control, Bulk and Interrupt endpoints. This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint), and by UDPHS_EPTCTLDISx (disable endpoint). • TX_PK_RDY/ERR_TRANS: TX Packet Ready/Transaction Error – TX Packet Ready: This bit is cleared by hardware, as soon as the packet has been sent for isochronous endpoints, or after the host has acknowledged the packet for Control, Bulk and Interrupt endpoints. For Multi-bank endpoints, this bit may remain clear even after software is set if another bank is available to transmit. Hardware clear of this bit may generate an interrupt if enabled by the UDPHS_EPTCTLx register TX_PK_RDY bit. This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint), and by UDPHS_EPTCTLDISx (disable endpoint). – Transaction Error: (For high bandwidth isochronous OUT endpoints) (Read-Only) This bit is set by hardware when a transaction error occurs inside one microframe. If one toggle sequencing problem occurs among the n-transactions (n = 1, 2 or 3) inside a microframe, then this bit is still set as long as the current bank contains one “bad” n-transaction. (see “CURRENT_BANK/CONTROL_DIR: Current Bank/Control Direction” on page 961) As soon as the current bank is relative to a new “good” n-transactions, then this bit is reset. SAM9M11 [DATASHEET] 959 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Note1: A transaction error occurs when the toggle sequencing does not respect the Universal Serial Bus Specification, Rev 2.0 (5.9.2 High Bandwidth Isochronous endpoints) (Bad PID, missing data....) Note2: When a transaction error occurs, the user may empty all the “bad” transactions by clearing the Received OUT Data flag (RX_BK_RDY). If this bit is reset, then the user should consider that a new n-transaction is coming. This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint), and by UDPHS_EPTCTLDISx (disable endpoint). • RX_SETUP/ERR_FL_ISO: Received SETUP/Error Flow – Received SETUP: (for Control endpoint only) This bit is set by hardware when a valid SETUP packet has been received from the host. It is cleared by the device firmware after reading the SETUP data from the endpoint FIFO. This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint), and by UDPHS_EPTCTLDISx (disable endpoint). – Error Flow: (for isochronous endpoint only) This bit is set by hardware when a transaction error occurs. – Isochronous IN transaction is missed, the micro has no time to fill the endpoint (underflow). – Isochronous OUT data is dropped because the bank is busy (overflow). This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint) and by UDPHS_EPTCTLDISx (disable endpoint). • STALL_SNT/ERR_CRISO/ERR_NBTRA: Stall Sent/CRC ISO Error/Number of Transaction Error – STALL_SNT: (for Control, Bulk and Interrupt endpoints) This bit is set by hardware after a STALL handshake has been sent as requested by the UDPHS_EPTSTAx register FRCESTALL bit. This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint) and by UDPHS_EPTCTLDISx (disable endpoint). – ERR_CRISO: (for Isochronous OUT endpoints) (Read-only) This bit is set by hardware if the last received data is corrupted (CRC error on data). This bit is updated by hardware when new data is received (Received OUT Data bit). – ERR_NBTRA: (for High Bandwidth Isochronous IN endpoints) This bit is set at the end of a microframe in which at least one data bank has been transmitted, if less than the number of transactions per micro-frame banks (UDPHS_EPTCFGx register NB_TRANS) have been validated for transmission inside this microframe. This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint) and by UDPHS_EPTCTLDISx (disable endpoint). • NAK_IN/ERR_FLUSH: NAK IN/Bank Flush Error – NAK_IN: This bit is set by hardware when a NAK handshake has been sent in response to an IN request from the Host. This bit is cleared by software. – ERR_FLUSH: (for High Bandwidth Isochronous IN endpoints) This bit is set when flushing unsent banks at the end of a microframe. This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint) and by EPT_CTL_DISx (disable endpoint). • NAK_OUT: NAK OUT This bit is set by hardware when a NAK handshake has been sent in response to an OUT or PING request from the Host. This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint) and by EPT_CTL_DISx (disable endpoint). 960 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• CURRENT_BANK/CONTROL_DIR: Current Bank/Control Direction – Current Bank: (all endpoints except Control endpoint) These bits are set by hardware to indicate the number of the current bank. 00 Bank 0 (or single bank) 01 Bank 1 10 Bank 2 11 Invalid Note: The current bank is updated each time the user: – Sets the TX Packet Ready bit to prepare the next IN transfer and to switch to the next bank. – Clears the received OUT data bit to access the next bank. This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint) and by UDPHS_EPTCTLDISx (disable endpoint). – Control Direction: (for Control endpoint only) 0: A Control Write is requested by the Host. 1: A Control Read is requested by the Host. Note1: This bit corresponds with the 7th bit of the bmRequestType (Byte 0 of the Setup Data). Note2: This bit is updated after receiving new setup data. • BUSY_BANK_STA: Busy Bank Number These bits are set by hardware to indicate the number of busy banks. IN endpoint: it indicates the number of busy banks filled by the user, ready for IN transfer. OUT endpoint: it indicates the number of busy banks filled by OUT transaction from the Host. 00 All banks are free 01 1 busy bank 10 2 busy banks 11 3 busy banks • BYTE_COUNT: UDPHS Byte Count Byte count of a received data packet. This field is incremented after each write into the endpoint (to prepare an IN transfer). This field is decremented after each reading into the endpoint (OUT transfer). This field is also updated at RX_BK_RDY flag clear with the next bank. This field is also updated at TX_PK_RDY flag set with the next bank. This field is reset by EPT_x of UDPHS_EPTRST register. • SHRT_PCKT: Short Packet An OUT Short Packet is detected when the receive byte count is less than the configured UDPHS_EPTCFGx register EPT_Size. This bit is updated at the same time as the BYTE_COUNT field. This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint) and by UDPHS_EPTCTLDISx (disable endpoint). SAM9M11 [DATASHEET] 961 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.15UDPHS DMA Channel Transfer Descriptor The DMA channel transfer descriptor is loaded from the memory. Be careful with the alignment of this buffer. The structure of the DMA channel transfer descriptor is defined by three parameters as described below: Offset 0: The address must be aligned: 0xXXXX0 Next Descriptor Address Register: UDPHS_DMANXTDSCx Offset 4: The address must be aligned: 0xXXXX4 DMA Channelx Address Register: UDPHS_DMAADDRESSx Offset 8: The address must be aligned: 0xXXXX8 DMA Channelx Control Register: UDPHS_DMACONTROLx To use the DMA channel transfer descriptor, fill the structures with the correct value (as described in the following pages). Then write directly in UDPHS_DMANXTDSCx the address of the descriptor to be used first. Then write 1 in the LDNXT_DSC bit of UDPHS_DMACONTROLx (load next channel transfer descriptor). The descriptor is automatically loaded upon Endpointx request for packet transfer. 962 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.16UDPHS DMA Next Descriptor Address Register Name: UDPHS_DMANXTDSCx [x = 1..5] Address: 0xFFF78320 [1], 0xFFF78330 [2], 0xFFF78340 [3], 0xFFF78350 [4], 0xFFF78360 [5] Access: Read/Write 31 30 29 28 27 26 25 24 NXT_DSC_ADD 23 22 21 20 19 18 17 16 NXT_DSC_ADD 15 14 13 12 11 10 9 8 NXT_DSC_ADD 7 6 5 4 3 2 1 0 NXT_DSC_ADD • NXT_DSC_ADD This field points to the next channel descriptor to be processed. This channel descriptor must be aligned, so bits 0 to 3 of the address must be equal to zero. SAM9M11 [DATASHEET] 963 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.17UDPHS DMA Channel Address Register Name: UDPHS_DMAADDRESSx [x = 1..5] Address: 0xFFF78324 [1], 0xFFF78334 [2], 0xFFF78344 [3], 0xFFF78354 [4], 0xFFF78364 [5] Access: Read/Write 31 30 29 28 27 26 25 24 BUFF_ADD 23 22 21 20 19 18 17 16 BUFF_ADD 15 14 13 12 11 10 9 8 BUFF_ADD 7 6 5 4 3 2 1 0 BUFF_ADD • BUFF_ADD This field determines the AHB bus starting address of a DMA channel transfer. Channel start and end addresses may be aligned on any byte boundary. The firmware may write this field only when the UDPHS_DMASTATUS register CHANN_ENB bit is clear. This field is updated at the end of the address phase of the current access to the AHB bus. It is incrementing of the access byte width. The access width is 4 bytes (or less) at packet start or end, if the start or end address is not aligned on a word boundary. The packet start address is either the channel start address or the next channel address to be accessed in the channel buffer. The packet end address is either the channel end address or the latest channel address accessed in the channel buffer. The channel start address is written by software or loaded from the descriptor, whereas the channel end address is either determined by the end of buffer or the UDPHS device, USB end of transfer if the UDPHS_DMACONTROLx register END_TR_EN bit is set. 964 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.18UDPHS DMA Channel Control Register Name: UDPHS_DMACONTROLx [x = 1..5] Address: 0xFFF78328 [1], 0xFFF78338 [2], 0xFFF78348 [3], 0xFFF78358 [4], 0xFFF78368 [5] Access: Read/Write 31 30 29 28 27 26 25 24 BUFF_LENGTH 23 22 21 20 19 18 17 16 BUFF_LENGTH 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 BURST_LCK DESC_LD_IT END_BUFFIT END_TR_IT END_B_EN END_TR_EN LDNXT_DSC CHANN_ENB • CHANN_ENB (Channel Enable Command) 0: DMA channel is disabled at and no transfer will occur upon request. This bit is also cleared by hardware when the chan- nel source bus is disabled at end of buffer. If the UDPHS_DMACONTROL register LDNXT_DSC bit has been cleared by descriptor loading, the firmware will have to set the corresponding CHANN_ENB bit to start the described transfer, if needed. If the UDPHS_DMACONTROL register LDNXT_DSC bit is cleared, the channel is frozen and the channel registers may then be read and/or written reliably as soon as both UDPHS_DMASTATUS register CHANN_ENB and CHANN_ACT flags read as 0. If a channel request is currently serviced when this bit is cleared, the DMA FIFO buffer is drained until it is empty, then the UDPHS_DMASTATUS register CHANN_ENB bit is cleared. If the LDNXT_DSC bit is set at or after this bit clearing, then the currently loaded descriptor is skipped (no data transfer occurs) and the next descriptor is immediately loaded. 1: UDPHS_DMASTATUS register CHANN_ENB bit will be set, thus enabling DMA channel data transfer. Then any pend- ing request will start the transfer. This may be used to start or resume any requested transfer. • LDNXT_DSC: Load Next Channel Transfer Descriptor Enable (Command) 0: No channel register is loaded after the end of the channel transfer. 1: The channel controller loads the next descriptor after the end of the current transfer, i.e., when the UDPHS_DMASTATUS/CHANN_ENB bit is reset. If the UDPHS_DMA CONTROL/CHANN_ENB bit is cleared, the next descriptor is immediately loaded upon transfer request. DMA Channel Control Command Summary LDNXT_DSC CHANN_ENB Description 0 0 Stop now 0 1 Run and stop at end of buffer 1 0 Load next descriptor now 1 1 Run and link at end of buffer SAM9M11 [DATASHEET] 965 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• END_TR_EN: End of Transfer Enable (Control) Used for OUT transfers only. 0: USB end of transfer is ignored. 1: UDPHS device can put an end to the current buffer transfer. When set, a BULK or INTERRUPT short packet or the last packet of an ISOCHRONOUS (micro) frame (DATAX) will close the current buffer and the UDPHS_DMASTATUSx register END_TR_ST flag will be raised. This is intended for UDPHS non-prenegotiated end of transfer (BULK or INTERRUPT) or ISOCHRONOUS microframe data buffer closure. • END_B_EN: End of Buffer Enable (Control) 0: DMA Buffer End has no impact on USB packet transfer. 1: Endpoint can validate the packet (according to the values programmed in the UDPHS_EPTCTLx register AUTO_VALID and SHRT_PCKT fields) at DMA Buffer End, i.e., when the UDPHS_DMASTATUS register BUFF_COUNT reaches 0. This is mainly for short packet IN validation initiated by the DMA reaching end of buffer, but could be used for OUT packet truncation (discarding of unwanted packet data) at the end of DMA buffer. • END_TR_IT: End of Transfer Interrupt Enable 0: UDPHS device initiated buffer transfer completion will not trigger any interrupt at UDPHS_STATUSx/END_TR_ST rising. 1: An interrupt is sent after the buffer transfer is complete, if the UDPHS device has ended the buffer transfer. Use when the receive size is unknown. • END_BUFFIT: End of Buffer Interrupt Enable 0: UDPHS_DMA_STATUSx/END_BF_ST rising will not trigger any interrupt. 1: An interrupt is generated when the UDPHS_DMASTATUSx register BUFF_COUNT reaches zero. • DESC_LD_IT: Descriptor Loaded Interrupt Enable 0: UDPHS_DMASTATUSx/DESC_LDST rising will not trigger any interrupt. 1: An interrupt is generated when a descriptor has been loaded from the bus. • BURST_LCK: Burst Lock Enable 0: The DMA never locks bus access. 1: USB packets AHB data bursts are locked for maximum optimization of the bus bandwidth usage and maximization of fly- by AHB burst duration. • BUFF_LENGTH: Buffer Byte Length (Write-only) This field determines the number of bytes to be transferred until end of buffer. The maximum channel transfer size (64 Kbytes) is reached when this field is 0 (default value). If the transfer size is unknown, this field should be set to 0, but the transfer end may occur earlier under UDPHS device control. When this field is written, The UDPHS_DMASTATUSx register BUFF_COUNT field is updated with the write value. Note: Bits [31:2] are only writable when issuing a channel Control Command other than “Stop Now”. Note: For reliability it is highly recommended to wait for both UDPHS_DMASTATUSx register CHAN_ACT and CHAN_ENB flags are at 0, thus ensuring the channel has been stopped before issuing a command other than “Stop Now”. 966 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

39.6.19UDPHS DMA Channel Status Register Name: UDPHS_DMASTATUSx [x = 1..5] Address: 0xFFF7832C [1], 0xFFF7833C [2], 0xFFF7834C [3], 0xFFF7835C [4], 0xFFF7836C [5] Access: Read/Write 31 30 29 28 27 26 25 24 BUFF_COUNT 23 22 21 20 19 18 17 16 BUFF_COUNT 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – DESC_LDST END_BF_ST END_TR_ST – – CHANN_ACT CHANN_ENB • CHANN_ENB: Channel Enable Status 0: If cleared, the DMA channel no longer transfers data, and may load the next descriptor if the UDPHS_DMACONTROLx register LDNXT_DSC bit is set. When any transfer is ended either due to an elapsed byte count or a UDPHS device initiated transfer end, this bit is auto- matically reset. 1: If set, the DMA channel is currently enabled and transfers data upon request. This bit is normally set or cleared by writing into the UDPHS_DMACONTROLx register CHANN_ENB bit field either by software or descriptor loading. If a channel request is currently serviced when the UDPHS_DMACONTROLx register CHANN_ENB bit is cleared, the DMA FIFO buffer is drained until it is empty, then this status bit is cleared. • CHANN_ACT: Channel Active Status 0: The DMA channel is no longer trying to source the packet data. When a packet transfer is ended this bit is automatically reset. 1: The DMA channel is currently trying to source packet data, i.e., selected as the highest-priority requesting channel. When a packet transfer cannot be completed due to an END_BF_ST, this flag stays set during the next channel descriptor load (if any) and potentially until UDPHS packet transfer completion, if allowed by the new descriptor. • END_TR_ST: End of Channel Transfer Status 0: Cleared automatically when read by software. 1: Set by hardware when the last packet transfer is complete, if the UDPHS device has ended the transfer. Valid until the CHANN_ENB flag is cleared at the end of the next buffer transfer. • END_BF_ST: End of Channel Buffer Status 0: Cleared automatically when read by software. 1: Set by hardware when the BUFF_COUNT downcount reach zero. Valid until the CHANN_ENB flag is cleared at the end of the next buffer transfer. SAM9M11 [DATASHEET] 967 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DESC_LDST: Descriptor Loaded Status 0: Cleared automatically when read by software. 1: Set by hardware when a descriptor has been loaded from the system bus. Valid until the CHANN_ENB flag is cleared at the end of the next buffer transfer. • BUFF_COUNT: Buffer Byte Count This field determines the current number of bytes still to be transferred for this buffer. This field is decremented from the AHB source bus access byte width at the end of this bus address phase. The access byte width is 4 by default, or less, at DMA start or end, if the start or end address is not aligned on a word boundary. At the end of buffer, the DMA accesses the UDPHS device only for the number of bytes needed to complete it. This field value is reliable (stable) only if the channel has been stopped or frozen (UDPHS_EPTCTLx register NT_DIS_DMA bit is used to disable the channel request) and the channel is no longer active CHANN_ACT flag is 0. Note: For OUT endpoints, if the receive buffer byte length (BUFF_LENGTH) has been defaulted to zero because the USB transfer length is unknown, the actual buffer byte length received will be 0x10000-BUFF_COUNT. 968 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40. Image Sensor Interface (ISI) 40.1 Description The Image Sensor Interface (ISI) connects a CMOS-type image sensor to the processor and provides image capture in various formats. It does data conversion, if necessary, before the storage in memory through DMA. The ISI supports color CMOS image sensor and grayscale image sensors with a reduced set of functionalities. In grayscale mode, the data stream is stored in memory without any processing and so is not compatible with the LCD controller. Internal FIFOs on the preview and codec paths are used to store the incoming data. The RGB output on the preview path is compatible with the LCD controller. This module outputs the data in RGB format (LCD compatible) and has scaling capabilities to make it compliant to the LCD display resolution (See Table 40-3 on page 972). Several input formats such as preprocessed RGB or YCbCr are supported through the data bus interface. It supports two modes of synchronization: 1. The hardware with ISI_VSYNC and ISI_HSYNC signals 2. The International Telecommunication Union Recommendation ITU-R BT.656-4 Start-of-Active-Video (SAV) and End-of-Active-Video (EAV) synchronization sequence. Using EAV/SAV for synchronization reduces the pin count (ISI_VSYNC, ISI_HSYNC not used). The polarity of the synchronization pulse is programmable to comply with the sensor signals. Table 40-1. I/O Description Signal Dir Description ISI_VSYNC IN Vertical Synchronization ISI_HSYNC IN Horizontal Synchronization ISI_DATA[11..0] IN Sensor Pixel Data ISI_MCK OUT Master Clock Provided to the Image Sensor ISI_PCK IN Pixel Clock Provided by the Image Sensor 40.2 Embedded Characteristics  ITU-R BT. 601/656 8-bit mode external interface support  Support for ITU-R BT.656-4 SAV and EAV synchronization  Vertical and horizontal resolutions up to 2048 x 2048  Preview Path up to 640*480  Support for packed data formatting for YCbCr 4:2:2 formats  Preview scaler to generate smaller size image SAM9M11 [DATASHEET] 969 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 40-1. ISI Connection Example Image Sensor Image Sensor Interface data[11..0] ISI_DATA[11..0] CLK ISI_MCK PCLK ISI_PCK VSYNC ISI_VSYNC HSYNC ISI_HSYNC 40.3 Block Diagram Figure 40-2. Image Sensor Interface Block Diagram s Hsync/Len Timing Signals u Vsync/Fen Interface Config APB B b Camera Registers Interface P Interrupt A Controller Camera Interrupt Request Line APB CCIR-656 Clock Domain Embedded Timing From Decoder(SAV/EAV) Rx buffers Pixel AHB CMOS Clock Domain Clock Domain sensor Frame Rate Pupix etol i1n2p ubtit CliCppoinnvge +rs iCoonlor 2-D Image Pixel RDxi sDpilraeyct Camera Scaler Formatter AHB s YCbCr 4:2:2 Pixel Sampling YCC to RGB FIFO Core Master bu 8:8:8 Module Video Interface B RGB 5:6:5 Arbiter Scatter AH Clipping + Color Packed Rx Direct Mode Conversion Formatter Capture Support RGB to YCC FIFO CMOS sensor pixel clock codec_on input 970 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.4 Functional Description The Image Sensor Interface (ISI) supports direct connection to the ITU-R BT. 601/656 8-bit mode compliant sensors and up to 12-bit grayscale sensors. It receives the image data stream from the image sensor on the 12-bit data bus. This module receives up to 12 bits for data, the horizontal and vertical synchronizations and the pixel clock. The reduced pin count alternative for synchronization is supported for sensors that embed SAV (start of active video) and EAV (end of active video) delimiters in the data stream. The Image Sensor Interface interrupt line is connected to the Advanced Interrupt Controller and can trigger an interrupt at the beginning of each frame and at the end of a DMA frame transfer. If the SAV/EAV synchronization is used, an interrupt can be triggered on each delimiter event. For 8-bit color sensors, the data stream received can be in several possible formats: YCbCr 4:2:2, RGB 8:8:8, RGB 5:6:5 and may be processed before the storage in memory. The data stream may be sent on both preview path and codec path if the bit ISI_CDC in the ISI_CTRL is one. To optimize the bandwidth, the codec path should be enabled only when a capture is required. In grayscale mode, the input data stream is stored in memory without any processing. The 12-bit data, which represent the grayscale level for the pixel, is stored in memory one or two pixels per word, depending on the GS_MODE bit in the ISI_CFG2 register. The codec datapath is not available when grayscale image is selected. A frame rate counter allows users to capture all frames or 1 out of every 2 to 8 frames. 40.4.1 Data Timing The two data timings using horizontal and vertical synchronization and EAV/SAV sequence synchronization are shown in Figure 40-3 and Figure 40-4. In the VSYNC/HSYNC synchronization, the valid data is captured with the active edge of the pixel clock (ISI_PCK), after SFD lines of vertical blanking and SLD pixel clock periods delay programmed in the control register. The ITU-RBT.656-4 defines the functional timing for an 8-bit wide interface. There are two timing reference signals, one at the beginning of each video data block SAV (0xFF000080) and one at the end of each video data block EAV(0xFF00009D). Only data sent between EAV and SAV is captured. Horizontal blanking and vertical blanking are ignored. Use of the SAV and EAV synchronization eliminates the ISI_VSYNC and ISI_HSYNC signals from the interface, thereby reducing the pin count. In order to retrieve both frame and line synchronization properly, at least one line of vertical blanking is mandatory. Figure 40-3. HSYNC and VSYNC Synchronization Frame ISI_VSYNC 1 line ISI_HSYNC ISI_PCK DATA[7..0] Y Cb Y Cr Y Cb Y Cr Y Cb Y Cr SAM9M11 [DATASHEET] 971 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 40-4. SAV and EAV Sequence Synchronization ISII_PCK DATA[7..0] FF 00 00 80 Y Cb Y Cr Y Cb Y Cr Y Y Cr Y Cb FF 00 00 9D SAV Active Video EAV 40.4.2 Data Ordering The RGB color space format is required for viewing images on a display screen preview, and the YCbCr color space format is required for encoding. All the sensors do not output the YCbCr or RGB components in the same order. The ISI allows the user to program the same component order as the sensor, reducing software treatments to restore the right format. Table 40-2. Data Ordering in YCbCr Mode Mode Byte 0 Byte 1 Byte 2 Byte 3 Default Cb(i) Y(i) Cr(i) Y(i+1) Mode1 Cr(i) Y(i) Cb(i) Y(i+1) Mode2 Y(i) Cb(i) Y(i+1) Cr(i) Mode3 Y(i) Cr(i) Y(i+1) Cb(i) Table 40-3. RGB Format in Default Mode, RGB_CFG = 00, No Swap Mode Byte D7 D6 D5 D4 D3 D2 D1 D0 Byte 0 R7(i) R6(i) R5(i) R4(i) R3(i) R2(i) R1(i) R0(i) Byte 1 G7(i) G6(i) G5(i) G4(i) G3(i) G2(i) G1(i) G0(i) RGB 8:8:8 Byte 2 B7(i) B6(i) B5(i) B4(i) B3(i) B2(i) B1(i) B0(i) Byte 3 R7(i+1) R6(i+1) R5(i+1) R4(i+1) R3(i+1) R2(i+1) R1(i+1) R0(i+1) Byte 0 R4(i) R3(i) R2(i) R1(i) R0(i) G5(i) G4(i) G3(i) Byte 1 G2(i) G1(i) G0(i) B4(i) B3(i) B2(i) B1(i) B0(i) RGB 5:6:5 Byte 2 R4(i+1) R3(i+1) R2(i+1) R1(i+1) R0(i+1) G5(i+1) G4(i+1) G3(i+1) Byte 3 G2(i+1) G1(i+1) G0(i+1) B4(i+1) B3(i+1) B2(i+1) B1(i+1) B0(i+1) Table 40-4. RGB Format, RGB_CFG = 10 (Mode 2), No Swap Mode Byte D7 D6 D5 D4 D3 D2 D1 D0 Byte 0 G2(i) G1(i) G0(i) R4(i) R3(i) R2(i) R1(i) R0(i) Byte 1 B4(i) B3(i) B2(i) B1(i) B0(i) G5(i) G4(i) G3(i) RGB 5:6:5 Byte 2 G2(i+1) G1(i+1) G0(i+1) R4(i+1) R3(i+1) R2(i+1) R1(i+1) R0(i+1) Byte 3 B4(i+1) B3(i+1) B2(i+1) B1(i+1) B0(i+1) G5(i+1) G4(i+1) G3(i+1) 972 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 40-5. RGB Format in Default Mode, RGB_CFG = 00, Swap Activated Mode Byte D7 D6 D5 D4 D3 D2 D1 D0 Byte 0 R0(i) R1(i) R2(i) R3(i) R4(i) R5(i) R6(i) R7(i) Byte 1 G0(i) G1(i) G2(i) G3(i) G4(i) G5(i) G6(i) G7(i) RGB 8:8:8 Byte 2 B0(i) B1(i) B2(i) B3(i) B4(i) B5(i) B6(i) B7(i) Byte 3 R0(i+1) R1(i+1) R2(i+1) R3(i+1) R4(i+1) R5(i+1) R6(i+1) R7(i+1) Byte 0 G3(i) G4(i) G5(i) R0(i) R1(i) R2(i) R3(i) R4(i) Byte 1 B0(i) B1(i) B2(i) B3(i) B4(i) G0(i) G1(i) G2(i) RGB 5:6:5 Byte 2 G3(i+1) G4(i+1) G5(i+1) R0(i+1) R1(i+1) R2(i+1) R3(i+1) R4(i+1) Byte 3 B0(i+1) B1(i+1) B2(i+1) B3(i+1) B4(i+1) G0(i+1) G1(i+1) G2(i+1) The RGB 5:6:5 input format is processed to be displayed as RGB 5:6:5 format, compliant with the 16-bit mode of the LCD controller. 40.4.3 Clocks The sensor master clock (ISI_MCK) can be generated either by the Advanced Power Management Controller (APMC) through a Programmable Clock output or by an external oscillator connected to the sensor. None of the sensors embed a power management controller, so providing the clock by the APMC is a simple and efficient way to control power consumption of the system. Care must be taken when programming the system clock. The ISI has two clock domains, the system bus clock and the pixel clock provided by sensor. The two clock domains are not synchronized, but the system clock must be faster than pixel clock. SAM9M11 [DATASHEET] 973 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.4.4 Preview Path 40.4.4.1 Scaling, Decimation (Subsampling) This module resizes captured 8-bit color sensor images to fit the LCD display format. The resize module performs only downscaling. The same ratio is applied for both horizontal and vertical resize, then a fractional decimation algorithm is applied. The decimation factor is a multiple of 1/16 and values 0 to 15 are forbidden. Table 40-6. Decimation Factor Dec value 0->15 16 17 18 19 ... 124 125 126 127 Dec Factor X 1 1.063 1.125 1.188 ... 7.750 7.813 7.875 7.938 Table 40-7. Decimation and Scaler Offset Values INPUT 352*288 640*480 800*600 1280*1024 1600*1200 2048*1536 OUTPUT VGA F NA 16 20 32 40 51 640*480 QVGA F 16 32 40 64 80 102 320*240 CIF F 16 26 33 56 66 85 352*288 QCIF F 32 53 66 113 133 170 176*144 Example: Input 1280*1024 Output = 640*480 Hratio = 1280/640 = 2 Vratio = 1024/480 = 2.1333 The decimation factor is 2 so 32/16. 974 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 40-5. Resize Examples 1280 32/16 decimation 640 1024 480 1280 56/16 decimation 352 1024 288 40.4.4.2 Color Space Conversion This module converts YCrCb or YUV pixels to RGB color space. Clipping is performed to ensure that the samples value do not exceed the allowable range. The conversion matrix is defined below and is fully programmable: C 0 C Y–Y R 0 1 off G = C –C –C × C –C 0 2 3 b boff B C C 0 C –C 0 4 r roff Example of programmable value to convert YCrCb to RGB: R = 1.164⋅(Y–16)+1.596⋅(Cr–128)  G = 1.164⋅(Y–16)–0.813⋅(Cr–128)–0.392⋅(Cb–128)  B = 1.164⋅(Y–16)+2.107⋅(Cb–128) An example of programmable value to convert from YUV to RGB: R = Y+1.596⋅V  G = Y–0.394⋅U–0.436⋅V B = Y+2.032⋅U  SAM9M11 [DATASHEET] 975 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.4.4.3 Memory Interface Preview datapath contains a data formatter that converts 8:8:8 pixel to RGB 5:6:5 format compliant with 16-bit format of the LCD controller. In general, when converting from a color channel with more bits to one with fewer bits, formatter module discards the lower-order bits. Example: Converting from RGB 8:8:8 to RGB 5:6:5, it discards the three LSBs from the red and blue channels, and two LSBs from the green channel. When grayscale mode is enabled, two memory formats are supported. One mode supports two pixels per word, and the other mode supports one pixel per word. Table 40-8. Grayscale Memory Mapping Configuration for 12-bit Data GS_MODE DATA[31:24] DATA[23:16] DATA[15:8] DATA[7:0] 0 P_0[11:4] P_0[3:0], 0000 P_1[11:4] P_1[3:0], 0000 1 P_0[11:4] P_0[3:0], 0000 0 0 40.4.4.4 FIFO and DMA Features Both preview and codec datapaths contain FIFOs. These asynchronous buffers are used to safely transfer formatted pixels from Pixel clock domain to AHB clock domain. A video arbiter is used to manage FIFO thresholds and triggers a relevant DMA request through the AHB master interface. Thus, depending on FIFO state, a specified length burst is asserted. Regarding AHB master interface, it supports Scatter DMA mode through linked list operation. This mode of operation improves flexibility of image buffer location and allows the user to allocate two or more frame buffers. The destination frame buffers are defined by a series of Frame Buffer Descriptors (FBD). Each FBD controls the transfer of one entire frame and then optionally loads a further FBD to switch the DMA operation at another frame buffer address. The FBD is defined by a series of three words. The first one defines the current frame buffer address (named DMA_X_ADDR register), the second defines control information (named DMA_X_CTRL register) and the third defines the next descriptor address (named DMA_X_DSCR). DMA transfer mode with linked list support is available for both codec and preview datapath. The data to be transferred described by an FBD requires several burst accesses. In the example below, the use of two ping-pong frame buffers is described. 976 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.4.4.5 Example The first FBD, stored at address 0x00030000, defines the location of the first frame buffer. This address is programmed in the ISI user interface DMA_P_DSCR. To enable Descriptor fetch operation DMA_P_CTRL register must be set to 0x00000001. LLI_0 and LLI_1 are the two descriptors of the Linked list. Destination Address: frame buffer ID0 0x02A000 (LLI_0.DMA_P_ADDR) Transfer 0 Control Information, fetch and writeback: 0x00000003 (LLI_0.DMA_P_CTRL) Next FBD address: 0x00030010 (LLI_0.DMA_P_DSCR) Second FBD, stored at address 0x00030010, defines the location of the second frame buffer. Destination Address: frame buffer ID1 0x0003A000 (LLI_1.DMA_P_ADDR Transfer 1 Control information fetch and writeback: 0x00000003 (LLI_1.DMA_P_CTRL) Next FBD address: 0x00030000, wrapping to first FBD (LLI_1.DMA_P_DSCR) Using this technique, several frame buffers can be configured through the linked list. Figure 40-6 illustrates a typical three frame buffer application. Frame n is mapped to frame buffer 0, frame n+1 is mapped to frame buffer 1, frame n+2 is mapped to Frame buffer 2, further frames wrap. A codec request occurs, and the full-size 4:2:2 encoded frame is stored in a dedicated memory space. Figure 40-6. Three Frame Buffers Application and Memory Mapping Codec Done Codec Request frame n-1 frame n frame n+1 frame n+2 frame n+3 frame n+4 Memory Space Frame Buffer 3 Frame Buffer 0 LCD Frame Buffer 1 ISI config Space 4:2:2 Image Full ROI SAM9M11 [DATASHEET] 977 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.4.5 Codec Path 40.4.5.1 Color Space Conversion Depending on user selection, this module can be bypassed so that input YCrCb stream is directly connected to the format converter module. If the RGB input stream is selected, this module converts RGB to YCrCb color space with the formulas given below: Y C0 C1 C2 R Yoff Cr = C3 –C4 –C5 × G + Croff C –C –C C B Cb b 6 7 8 off An example of coefficients is given below: Y = 0.257⋅R+0.504⋅G+0.098⋅B+16 Cr = 0.439⋅R–0.368⋅G–0.071⋅B+128 C = –0.148⋅R–0.291⋅G+0.439⋅B+128  b 40.4.5.2 Memory Interface Dedicated FIFOs are used to support packed memory mapping. YCrCb pixel components are sent in a single 32- bit word in a contiguous space (packed). Data is stored in the order of natural scan lines. Planar mode is not supported. 40.4.5.3 DMA Features Like preview datapath, codec datapath DMA mode uses linked list operation. 978 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5 Image Sensor Interface (ISI) User Interface Table 40-9. Register Mapping Offset Register Name Register Access Reset Value 0x00 ISI Configuration 1 Register ISI_CFG1 Read/Write 0x00000000 0x04 ISI Configuration 2 Register ISI_CFG2 Read/Write 0x00000000 0x08 ISI Preview Size Register ISI_PSIZE Read/Write 0x00000000 0x0C ISI Preview Decimation Factor Register ISI_PDECF Read/Write 0x00000010 0x10 ISI CSC YCrCb To RGB Set 0 Register ISI_Y2R_SET0 Read/Write 0x6832CC95 0x14 ISI CSC YCrCb To RGB Set 1 Register ISI_Y2R_SET1 Read/Write 0x00007102 0x18 ISI CSC RGB To YCrCb Set 0 Register ISI_R2Y_SET0 Read/Write 0x01324145 0x1C ISI CSC RGB To YCrCb Set 1 Register ISI_R2Y_SET1 Read/Write 0x01245E38 0x20 ISI CSC RGB To YCrCb Set 2 Register ISI_R2Y_SET2 Read/Write 0x01384A4B 0x24 ISI Control Register ISI_CTRL Write-only – 0x28 ISI Status Register ISI_STATUS Read-only 0x00000000 0x2C ISI Interrupt Enable Register ISI_INTEN Write-only – 0x30 ISI Interrupt Disable Register ISI_INTDIS Write-only – 0x34 ISI Interrupt Mask Register ISI_INTMASK Read-only 0x00000000 0x38 DMA Channel Enable Register DMA_CHER Write-only – 0x3C DMA Channel Disable Register DMA_CHDR Write-only – 0x40 DMA Channel Status Register DMA_CHSR Read-only 0x00000000 0x44 DMA Preview Base Address Register DMA_P_ADDR Read/Write 0x00000000 0x48 DMA Preview Control Register DMA_P_CTRL Read/Write 0x00000000 0x4C DMA Preview Descriptor Address Register DMA_P_DSCR Read/Write 0x00000000 0x50 DMA Codec Base Address Register DMA_C_ADDR Read/Write 0x00000000 0x54 DMA Codec Control Register DMA_C_CTRL Read/Write 0x00000000 0x58 DMA Codec Descriptor Address Register DMA_C_DSCR Read/Write 0x00000000 0x5C–0xE0 Reserved – – – 0xE4 Write Protection Control Register ISI_WPCR Read/Write 0x00000000 0xE8 Write Protection Status Register ISI_WPSR Read-only 0x00000000 0xEC–0xF8 Reserved – – – 0xFC Reserved – – – Note: Several parts of the ISI controller use the pixel clock provided by the image sensor (ISI_PCK). Thus the user must first program the image sensor to provide this clock (ISI_PCK) before programming the Image Sensor Controller. SAM9M11 [DATASHEET] 979 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.1 ISI Configuration 1 Register Name: ISI_CFG1 Access: Read/Write 31 30 29 28 27 26 25 24 SFD 23 22 21 20 19 18 17 16 SLD 15 14 13 12 11 10 9 8 – THMASK FULL DISCR FRATE 7 6 5 4 3 2 1 0 CRC_SYNC EMB_SYNC – PIXCLK_POL VSYNC_POL HSYNC_POL – – • HSYNC_POL: Horizontal Synchronization Polarity 0: HSYNC active high. 1: HSYNC active low. • VSYNC_POL: Vertical Synchronization Polarity 0: VSYNC active high. 1: VSYNC active low. • PIXCLK_POL: Pixel Clock Polarity 0: Data is sampled on rising edge of pixel clock. 1: Data is sampled on falling edge of pixel clock. • EMB_SYNC: Embedded Synchronization 0: Synchronization by HSYNC, VSYNC. 1: Synchronization by embedded synchronization sequence SAV/EAV. • CRC_SYNC: Embedded Synchronization Correction 0: No CRC correction is performed on embedded synchronization. 1: CRC correction is performed. if the correction is not possible, the current frame is discarded and the CRC_ERR is set in the status register. • FRATE: Frame Rate [0..7] 0: All the frames are captured, else one frame every FRATE+1 is captured. • DISCR: Disable Codec Request 0: Codec datapath DMA interface requires a request to restart. 1: Codec datapath DMA automatically restarts. • FULL: Full Mode is Allowed 1: Both codec and preview datapaths are working simultaneously. 980 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• THMASK: Threshold Mask 0: Only 4 beats AHB burst are allowed. 1: Only 4 and 8 beats AHB burst are allowed. 2: 4, 8 and 16 beats AHB burst are allowed. • SLD: Start of Line Delay SLD pixel clock periods to wait before the beginning of a line. • SFD: Start of Frame Delay SFD lines are skipped at the beginning of the frame. SAM9M11 [DATASHEET] 981 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.2 ISI Configuration 2 Register Name: ISI_CFG2 Access: Read/Write 31 30 29 28 27 26 25 24 RGB_CFG YCC_SWAP - IM_HSIZE 23 22 21 20 19 18 17 16 IM_HSIZE 15 14 13 12 11 10 9 8 COL_SPACE RGB_SWAP GRAYSCALE RGB_MODE GS_MODE IM_VSIZE 7 6 5 4 3 2 1 0 IM_VSIZE • IM_VSIZE: Vertical Size of the Image Sensor [0..2047] Vertical size = IM_VSIZE + 1. • GS_MODE 0: 2 pixels per word. 1: 1 pixel per word. • RGB_MODE: RGB Input Mode 0: RGB 8:8:8 24 bits. 1: RGB 5:6:5 16 bits. • GRAYSCALE 0: Grayscale mode is disabled. 1: Input image is assumed to be grayscale coded. • RGB_SWAP 0: D7 -> R7. 1: D0 -> R7. The RGB_SWAP has no effect when the grayscale mode is enabled. • COL_SPACE: Color Space for the Image Data 0: YCbCr. 1: RGB. • IM_HSIZE: Horizontal Size of the Image Sensor [0..2047] Horizontal size = IM_HSIZE + 1. 982 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• YCC_SWAP: Defines the YCC Image Data YCC_SWAP Byte 0 Byte 1 Byte 2 Byte 3 00: Default Cb(i) Y(i) Cr(i) Y(i+1) 01: Mode1 Cr(i) Y(i) Cb(i) Y(i+1) 10: Mode2 Y(i) Cb(i) Y(i+1) Cr(i) 11: Mode3 Y(i) Cr(i) Y(i+1) Cb(i) • RGB_CFG: Defines RGB Pattern when RGB_MODE is set to 1 RGB_CFG Byte 0 Byte 1 Byte 2 Byte 3 00: Default R/G(MSB) G(LSB)/B R/G(MSB) G(LSB)/B 01: Mode1 B/G(MSB) G(LSB)/R B/G(MSB) G(LSB)/R 10: Mode2 G(LSB)/R B/G(MSB) G(LSB)/R B/G(MSB) 11: Mode3 G(LSB)/B R/G(MSB) G(LSB)/B R/G(MSB) If RGB_MODE is set to RGB 8:8:8, then RGB_CFG = 0 implies RGB color sequence, else it implies BGR color sequence. SAM9M11 [DATASHEET] 983 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.3 ISI Preview Register Name: ISI_PSIZE Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – PREV_HSIZE 23 22 21 20 19 18 17 16 PREV_HSIZE 15 14 13 12 11 10 9 8 – – – – – – PREV_VSIZE 7 6 5 4 3 2 1 0 PREV_VSIZE • PREV_VSIZE: Vertical Size for the Preview Path Vertical Preview size = PREV_VSIZE + 1 (480 max only in RGB mode). • PREV_HSIZE: Horizontal Size for the Preview Path Horizontal Preview size = PREV_HSIZE + 1 (640 max only in RGB mode). 984 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.4 ISI Preview Decimation Factor Register Name: ISI_PDECF Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 DEC_FACTOR • DEC_FACTOR: Decimation Factor DEC_FACTOR is 8-bit width, range is from 16 to 255. Values from 0 to 16 do not perform any decimation. SAM9M11 [DATASHEET] 985 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.5 ISI Color Space Conversion YCrCb to RGB Set 0 Register Name: ISI_Y2R_SET0 Access: Read/Write 31 30 29 28 27 26 25 24 C3 23 22 21 20 19 18 17 16 C2 15 14 13 12 11 10 9 8 C1 7 6 5 4 3 2 1 0 C0 • C0: Color Space Conversion Matrix Coefficient C0 C0 element default step is 1/128, ranges from 0 to 1.9921875. • C1: Color Space Conversion Matrix Coefficient C1 C1 element default step is 1/128, ranges from 0 to 1.9921875. • C2: Color Space Conversion Matrix Coefficient C2 C2 element default step is 1/128, ranges from 0 to 1.9921875. • C3: Color Space Conversion Matrix Coefficient C3 C3 element default step is 1/128, ranges from 0 to 1.9921875. 986 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.6 ISI Color Space Conversion YCrCb to RGB Set 1 Register Name: ISI_Y2R_SET1 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – Cboff Croff Yoff – – – C4 C4 • C4: Color Space Conversion Matrix Coefficient C4 C4 element default step is 1/128, ranges from 0 to 3.9921875. • Yoff: Color Space Conversion Luminance Default Offset 0: No offset. 1: Offset = 128. • Croff: Color Space Conversion Red Chrominance Default Offset 0: No offset. 1: Offset = 16. • Cboff: Color Space Conversion Blue Chrominance Default Offset 0: No offset. 1: Offset = 16. SAM9M11 [DATASHEET] 987 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.7 ISI Color Space Conversion RGB to YCrCb Set 0 Register Name: ISI_R2Y_SET0 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – Roff 23 22 21 20 19 18 17 16 C2 15 14 13 12 11 10 9 8 C1 7 6 5 4 3 2 1 0 C0 • C0: Color Space Conversion Matrix Coefficient C0 C0 element default step is 1/256, from 0 to 0.49609375. • C1: Color Space Conversion Matrix Coefficient C1 C1 element default step is 1/128, from 0 to 0.9921875. • C2: Color Space Conversion Matrix Coefficient C2 C2 element default step is 1/512, from 0 to 0.2480468875. • Roff: Color Space Conversion Red Component Offset 0: No offset. 1: Offset = 16. 988 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.8 ISI Color Space Conversion RGB to YCrCb Set 1 Register Name: ISI_R2Y_SET1 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – Goff 23 22 21 20 19 18 17 16 C5 15 14 13 12 11 10 9 8 C4 7 6 5 4 3 2 1 0 C3 • C3: Color Space Conversion Matrix Coefficient C3 C0 element default step is 1/128, ranges from 0 to 0.9921875. • C4: Color Space Conversion Matrix Coefficient C4 C1 element default step is 1/256, ranges from 0 to 0.49609375. • C5: Color Space Conversion Matrix Coefficient C5 C1 element default step is 1/512, ranges from 0 to 0.2480468875. • Goff: Color Space Conversion Green Component Offset 0: No offset. 1: Offset = 128. SAM9M11 [DATASHEET] 989 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.9 ISI Color Space Conversion RGB to YCrCb Set 2 Register Name: ISI_R2Y_SET2 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – Boff 23 22 21 20 19 18 17 16 C8 15 14 13 12 11 10 9 8 C7 7 6 5 4 3 2 1 0 C6 • C6: Color Space Conversion Matrix Coefficient C6 C6 element default step is 1/512, ranges from 0 to 0.2480468875. • C7: Color Space Conversion Matrix Coefficient C7 C7 element default step is 1/256, ranges from 0 to 0.49609375. • C8: Color Space Conversion Matrix Coefficient C8 C8 element default step is 1/128, ranges from 0 to 0.9921875. • Boff: Color Space Conversion Blue Component Offset 0: No offset. 1: Offset = 128. 990 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.10ISI Control Register Name: ISI_CTRL Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – ISI_CDC 7 6 5 4 3 2 1 0 – – – – – ISI_SRST ISI_DIS ISI_EN • ISI_EN: ISI Module Enable Request Write one to this field to enable the module. Software must poll ENABLE field in the ISI_STATUS register to verify that the command has successfully completed. • ISI_DIS: ISI Module Disable Request Write one to this field to disable the module. If both ISI_EN and ISI_DIS are asserted at the same time, the disable request is not taken into account. Software must poll DIS_DONE field in the ISI_STATUS register to verify that the command has successfully completed. • ISI_SRST: ISI Software Reset Request Write one to this field to request a software reset of the module. Software must poll SRST field in the ISI_STATUS register to verify that the software request command has terminated. • ISI_CDC: ISI Codec Request Write one to this field to enable the codec datapath and capture a Full resolution Frame. A new request cannot be taken into account while CDC_PND bit is active in the ISI_STATUS register. SAM9M11 [DATASHEET] 991 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.11 ISI Status Register Name: ISI_SR Access: Read-only 31 30 29 28 27 26 25 24 – – – – FR_OVR CRC_ERR C_OVR P_OVR 23 22 21 20 19 18 17 16 – – – – SIP – CXFR_DONE PXFR_DONE 15 14 13 12 11 10 9 8 – – – – – VSYNC – CDC_PND 7 6 5 4 3 2 1 0 – – – – – SRST DIS_DONE ENABLE • ENABLE (this bit is a status bit) 0: Module is enabled. 1: Module is disabled. • DIS_DONE: Module Disable Request has Terminated 1: Disable request has completed. This flag is reset after a read operation. • SRST: Module Software Reset Request has Terminated 1: Software reset request has completed. This flag is reset after a read operation. • CDC_PND: Pending Codec Request (this bit is a status bit) 0: Indicates that no Codec request is pending. 1: Indicates that the request has been taken into account but cannot be serviced within the current frame. The operation is postponed to the next frame. • VSYNC: Vertical Synchronization 1: Indicates that a Vertical synchronization has been detected since the last read of the status register. • PXFR_DONE: Preview DMA Transfer has Terminated. When set to one, this bit indicates that the DATA transfer on the preview channel has completed. This flag is reset after a read operation. • CXFR_DONE: Codec DMA Transfer has Terminated. When set to one, this bit indicates that the DATA transfer on the codec channel has completed. This flag is reset after a read operation. • SIP: Synchronization in Progress (this is a status bit) When the status of the preview or codec DMA channel is modified, a minimum amount of time is required to perform the clock domain synchronization. This bit is set when this operation occurs. No modification of the channel status is allowed when this bit is set, to guarantee data integrity. 992 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• P_OVR: Preview Datapath Overflow 0: No overflow 1: An overrun condition has occurred in input FIFO on the preview path. The overrun happens when the FIFO is full and an attempt is made to write a new sample to the FIFO. This flag is reset after a read operation. • C_OVR: Codec Datapath Overflow 0: No overflow 1: An overrun condition has occurred in input FIFO on the codec path. The overrun happens when the FIFO is full and an attempt is made to write a new sample to the FIFO. This flag is reset after a read operation. • CRC_ERR: CRC Synchronization Error 0: No CRC error in the embedded synchronization frame (SAV/EAV) 1: The CRC_SYNC is enabled in the control register and an error has been detected and not corrected. The frame is dis- carded and the ISI waits for a new one. This flag is reset after a read operation. • FR_OVR: Frame Rate Overrun 0: No frame overrun. 1: Frame overrun, the current frame is being skipped because a vsync signal has been detected while flushing FIFOs. This flag is reset after a read operation. SAM9M11 [DATASHEET] 993 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.12ISI Interrupt Enable Register Name: ISI_IER Access: Read/Write 31 30 29 28 27 26 25 24 – – – – FR_OVR CRC_ERR C_OVR P_OVR 23 22 21 20 19 18 17 16 – – – – – – CXFR_DONE PXFR_DONE 15 14 13 12 11 10 9 8 – – – – – VSYNC – – 7 6 5 4 3 2 1 0 – – – – – SRST DIS_DONE – • DIS_DONE: Disable Done Interrupt Enable • SRST: Software Reset Interrupt Enable • VSYNC: Vertical Synchronization Interrupt Enable • PXFR_DONE: Preview DMA Transfer Done Interrupt Enable • CXFR_DONE: Codec DMA Transfer Done Interrupt Enable • P_OVR: Preview Datapath Overflow Interrupt Enable • C_OVR: Codec Datapath Overflow Interrupt Enable • CRC_ERR: Embedded Synchronization CRC Error Interrupt Enable • FR_OVR: Frame Rate Overflow Interrupt Enable 994 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.13ISI Interrupt Disable Register Name: ISI_IDR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – FR_OVR CRC_ERR C_OVR P_OVR 23 22 21 20 19 18 17 16 – – – – – – CXFR_DONE PXFR_DONE 15 14 13 12 11 10 9 8 – – – – – VSYNC – – 7 6 5 4 3 2 1 0 – – – – – SRST DIS_DONE – • DIS_DONE: Disable Done Interrupt Disable • SRST: Software Reset Interrupt Disable • VSYNC: Vertical Synchronization Interrupt Disable • PXFR_DONE: Preview DMA Transfer Done Interrupt Disable • CXFR_DONE: Codec DMA Transfer Done Interrupt Disable • P_OVR: Preview Datapath Overflow Interrupt Disable • C_OVR: Codec Datapath Overflow Interrupt Disable • CRC_ERR: Embedded Synchronization CRC Error Interrupt Disable • FR_OVR: Frame Rate Overflow Interrupt Disable SAM9M11 [DATASHEET] 995 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.14ISI Interrupt Mask Register Name: ISI_IMR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – FR_OVR CRC_ERR C_OVR P_OVR 23 22 21 20 19 18 17 16 – – – – – – CXFR_DONE PXFR_DONE 15 14 13 12 11 10 9 8 – – – – – VSYNC – – 7 6 5 4 3 2 1 0 – – – – – SRST DIS_DONE – • DIS_DONE: Module Disable Operation Completed 0: The disable completed interrupt is disabled. 1: The disable completed interrupt is enabled. • SRST: Software Reset Completed 0: The software reset completed interrupt is disabled. 1: The software reset completed interrupt is enabled. • VSYNC: Vertical Synchronization 0: The vertical synchronization interrupt is enabled. 1: The vertical synchronization interrupt is disabled. • PXFR_DONE: Preview DMA Transfer Interrupt 0: The Preview DMA transfer completed interrupt is enabled 1: The Preview DMA transfer completed interrupt is disabled • CXFR_DONE: Codec DMA Transfer Interrupt 0: The Codec DMA transfer completed interrupt is enabled 1: The Codec DMA transfer completed interrupt • P_OVR: FIFO Preview Overflow 0: The preview FIFO overflow interrupt is disabled. 1: The preview FIFO overflow interrupt is enabled. • P_OVR: FIFO Codec Overflow 0: The codec FIFO overflow interrupt is disabled. 1: The codec FIFO overflow interrupt is enabled. • CRC_ERR: CRC Synchronization Error 0: The crc error interrupt is disabled. 1: The crc error interrupt is enabled. 996 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• FR_OVR: Frame Rate Overrun 0: The frame overrun interrupt is disabled. 1: The frame overrun interrupt is enabled. SAM9M11 [DATASHEET] 997 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.15DMA Channel Enable Register Name: DMA_CHER Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – C_CH_EN P_CH_EN • P_CH_EN: Preview Channel Enable Write one to this field to enable the preview DMA channel. • C_CH_EN: Codec Channel Enable Write one to this field to enable the codec DMA channel. 998 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.16DMA Channel Disable Register Name: DMA_CHDR Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – C_CH_DIS P_CH_DIS • P_CH_DIS Write one to this field to disable the channel. Poll P_CH_S in DMA_CHSR to verify that the preview channel status has been successfully modified. • C_CH_DIS Write one to this field to disabled the channel. Poll C_CH_S in DMA_CHSR to verify that the codec channel status has been successfully modified. SAM9M11 [DATASHEET] 999 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.17DMA Channel Status Register Name: DMA_CHSR Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – C_CH_S P_CH_S • P_CH_S: 0: indicates that the Preview DMA channel is disabled 1: indicates that the Preview DMA channel is enabled. • C_CH_S: 0: indicates that the Codec DMA channel is disabled. 1: indicates that the Codec DMA channel is enabled. 1000 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.18DMA Preview Base Address Register Name: DMA_P_ADDR Access: Read/Write 31 30 29 28 27 26 25 24 P_ADDR 23 22 21 20 19 18 17 16 P_ADDR 15 14 13 12 11 10 9 8 P_ADDR 7 6 5 4 3 2 1 0 P_ADDR – – • P_ADDR: Preview Image Base Address. (This address is word aligned.) SAM9M11 [DATASHEET] 1001 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.19DMA Preview Control Register Name: DMA_P_CTRL Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – P_DONE P_IEN P_WB P_FETCH • P_FETCH: Descriptor Fetch Control Field 0: Preview channel fetch operation is disabled. 1: Preview channel fetch operation is enabled. • P_WB: Descriptor Writeback Control Field 0: Preview channel writeback operation is disabled. 1: Preview channel writeback operation is enabled. • P_IEN: Transfer Done Flag Control 0: Preview Transfer done flag generation is enabled. 1: Preview Transfer done flag generation is disabled. • P_DONE: (This field is only updated in the memory.) 0: The transfer related to this descriptor has not been performed. 1: The transfer related to this descriptor has completed. This field is updated in memory at the end of the transfer, when writeback operation is enabled. 1002 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.20DMA Preview Descriptor Address Register Name: DMA_P_DSCR Access: Read/Write 31 30 29 28 27 26 25 24 P_DSCR 23 22 21 20 19 18 17 16 P_DSCR 15 14 13 12 11 10 9 8 P_DSCR 7 6 5 4 3 2 1 0 P_DSCR – – • P_DSCR: Preview Descriptor Base Address (This address is word aligned.) SAM9M11 [DATASHEET] 1003 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.21DMA Codec Base Address Register Name: DMA_C_ADDR Access: Read/Write 31 30 29 28 27 26 25 24 C_ADDR 23 22 21 20 19 18 17 16 C_ADDR 15 14 13 12 11 10 9 8 C_ADDR 7 6 5 4 3 2 1 0 C_ADDR – – • C_ADDR: Codec Image Base Address (This address is word aligned.) 1004 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.22DMA Codec Control Register Name: DMA_C_CTRL Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – C_DONE C_IEN C_WB C_FETCH • C_FETCH: Descriptor Fetch Control Field 0: Codec channel fetch operation is disabled. 1: Codec channel fetch operation is enabled. • C_WB: Descriptor Writeback Control Field 0: Codec channel writeback operation is disabled. 1: Codec channel writeback operation is enabled. • C_IEN: Transfer Done flag control 0: Codec Transfer done flag generation is enabled. 1: Codec Transfer done flag generation is disabled. • C_DONE: (This field is only updated in the memory.) 0: The transfer related to this descriptor has not been performed. 1: The transfer related to this descriptor has completed. This field is updated in memory at the end of the transfer, when. writeback operation is enabled. SAM9M11 [DATASHEET] 1005 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.23DMA Codec Descriptor Address Register Name: DMA_C_DSCR Access: Read/Write 31 30 29 28 27 26 25 24 C_DSCR 23 22 21 20 19 18 17 16 C_DSCR 15 14 13 12 11 10 9 8 C_DSCR 7 6 5 4 3 2 1 0 C_DSCR – – • C_DSCR: Codec Descriptor Base Address (This address is word aligned.) 1006 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.24ISI Write Protection Control Name: ISI_WPCR Access: Read/Write 31 30 29 28 27 26 25 24 WP_KEY (0x49 => “I”) 23 22 21 20 19 18 17 16 WP_KEY (0x53 => “S”) 15 14 13 12 11 10 9 8 WP_KEY (0x49 => “I”) 7 6 5 4 3 2 1 0 WP_EN • WP_PEN: Write Protection Enable 0: Disables the Write Protection if WP_KEY corresponds. 1: Enables the Write Protection if WP_KEY corresponds. • WP_KEY: Write Protection KEY Password Should be written at value 0x495349 (ASCII code for “ISI”). Writing any other value in this field has no effect. SAM9M11 [DATASHEET] 1007 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

40.5.25ISI Write Protection Status Name: ISI_WPSR Access: Read/Write 31 30 29 28 27 26 25 24 - - - - - - - - 23 22 21 20 19 18 17 16 WP_VSRC 15 14 13 12 11 10 9 8 WP_VSRC 7 6 5 4 3 2 1 0 - - - - WP_VS • WP_VS: Write Protection Violation Status Value Description 0 0 0 0 No Write Protection Violation occurred since the last read of this register (WP_SR). 0 0 0 1 Write Protection detected unauthorized attempt to write a control register had occurred (since the last read). 0 0 1 0 Software reset had been performed while Write Protection was enabled (since the last read). 0 0 1 1 Both Write Protection violation and software reset with Write Protection enabled had occurred since the last read. Other value Reserved • WP_VSRC: Write Protection Violation Source Value Description 0 0 0 0 No Write Protection Violation occurred since the last read of this register (WP_SR). 0 0 0 1 Write access in ISI_CFG1 while Write Protection was enabled (since the last read). 0 0 1 0 Write access in ISI_CFG2 while Write Protection was enabled (since the last read). 0 0 1 1 Write access in ISI_PSIZE while Write Protection was enabled (since the last read). 0 1 0 0 Write access in ISI_PDECF while Write Protection was enabled (since the last read). 0 1 0 1 Write access in ISI_Y2R_SET0 while Write Protection was enabled (since the last read). 0 1 1 0 Write access in ISI_Y2R_SET1 while Write Protection was enabled (since the last read). 0 1 1 1 Write access in ISI_R2Y_SET0 while Write Protection was enabled (since the last read). 1 0 0 0 Write access in ISI_R2Y_SET1 while Write Protection was enabled (since the last read). 1 0 0 1 Write access in ISI_R2Y_SET2 while Write Protection was enabled (since the last read). Other value Reserved 1008 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41. Touchscreen ADC Controller (TSADCC) 41.1 Description The Touchscreen ADC Controller is based on a Successive Approximation Register (SAR) 10-bit Analog-to-Digital Converter (ADC). It also integrates:  an 8-to-1 analog multiplexer for analog-to-digital conversions of up to 8 analog lines  4 power switches that measure both axis positions on the resistive touchscreen panel  1 additional power switch and an embedded resistor that detects pen-interrupt and pen loss The conversions extend from 0V to TSADVREF. The TSADCC supports an 8-bit or 10-bit resolution mode, and conversion results are reported in a common register for all channels, as well as in a channel-dedicated register. Conversions can be started for all enabled channels, either by a software trigger, by detection of a rising edge on the external trigger pin TSADTRG or by an integrated programmable timer. When the Touchscreen is enabled, a timer-triggered sequencer automatically configures the power switches, performs the conversions and stores the results in dedicated registers. The TSADCC also integrates a Sleep Mode and a Pen-Detect Mode and connects with one PDC channel. These features reduce both power consumption and processor intervention. The TSADCC timings, like the Startup Time and Sample and Hold Time, are fully configurable. SAM9M11 [DATASHEET] 1009 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.2 Embedded Characteristics  8-channel 10-bit Analog-to-Digital Converter  Glueless interface with Resistive Touchscreen Panel, Allowing ̶ Touchscreen Position Measurement ̶ Pressure Measurement ̶ Pen Detection and Pen Loss Detection  Embeds ̶ 8-to-1 Multiplexer for Selection of the Analog Input ̶ Five Low-resistance Power Switches ̶ Pull-down Resistance for Pen-interrupt Detection  Integrated Enhanced Sequencer Supporting ̶ ADC Mode ̶ Touchscreen Mode ̶ Interleaved Mode ̶ Manual Mode  Sleep Mode ̶ Automatic Wakeup on Trigger and Back to Sleep Mode when sequence is performed  Numerous Trigger Sources ̶ Software ̶ Embedded 16-bit Timer for Periodic Trigger ̶ Pen Detect Trigger ̶ Continuous Trigger ̶ External Trigger, Rising, Falling or Any-edge Trigger  Programmable ADC Timings ̶ Programmable ADC Clock ̶ Programmable Startup Time ̶ Programmable Sample and Hold Time, Independent for Analog and Touchscreen Inputs 1010 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.3 Block Diagram Figure 41-1. TSADCC Block Diagram TSADC VDDANA TSADCC Memory Controller Trigger TSADTRG Selection Timer PDC PIO Touchscreen ADC Control Sequencer Logic User Peripheral Interface Bridge APB AD0X P n AAADDD132XYYMMP eercshcuoTsehctiwS og Multiplexer AAnSpaCpluRoorcegoncg-xvetiioemss-trsDeatievrtiigreointal TCSlAocDkC PMC al n GPAD4 A .... GPADx TSADC Interrupt TSADVREF AIC GND GPADx: last general-purpose ADC channel defined by the number of channels 41.4 Signal Description Table 41-1. TSADCC Pin Description Pin Name Description VDDANA Analog power supply TSADVREF Reference voltage AD0X Analog input channel 0 or Touchscreen Top channel P AD1X Analog input channel 1 or Touchscreen Bottom channel M AD2Y Analog input channel 2 or Touchscreen Right channel P AD3Y Analog input channel 3 or Touchscreen Left channel M GPAD4–GPAD7 General-purpose analog input channels 4 to 7 TSADTRG External trigger SAM9M11 [DATASHEET] 1011 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.5 Product Dependencies 41.5.1 Power Management The TSADC controller is not continuously clocked. The programmer must first enable the TSADC controller Clock in the Power Management Controller (PMC) before using the TSADC controller. However, if the application does not require TSADC controller operations, the TSADC controller clock can be stopped when not needed and be restarted later. Configuring the TSADC controller does not require the TSADC controller clock to be enabled. 41.5.2 Interrupt Sources The TSADCC interrupt line is connected on one of the internal sources of the Advanced Interrupt Controller. Using the TSADCC interrupt requires the AIC to be programmed first. Table 41-2. Peripheral IDs Instance ID TSADCC 20 41.5.3 Analog Inputs The analog input pins can be multiplexed with PIO lines. In this case, the assignment of the TSADCC input is automatically done as soon as the corresponding channel is enabled by writing the register TSADCC_CHER. By default, after reset, the PIO lines are configured as input with its pull-up enabled and the TSADCC inputs are connected to the GND. 41.5.4 I/O Lines The pin TSADTRG may be shared with other peripheral functions through the PIO Controller. In this case, the PIO Controller should be set accordingly to assign the pin TSADTRG to the TSADCC function. Table 41-3. I/O Lines Instance Signal I/O Line Peripheral TSADCC TSADTRG PD28 A 41.5.5 Conversion Performances For performance and electrical characteristics of the TSADCC, see the section “Electrical Characteristics” of the datasheet. 41.6 Analog-to-digital Converter Functional Description The TSADCC embeds a Successive Approximation Register (SAR) Analog-to-Digital Converter (ADC). The ADC supports 8-bit or 10-bit resolutions. The conversion is performed on a full range between 0V and the reference voltage pin TSADVREF. Analog inputs between these voltages convert to values based on a linear conversion. 41.6.1 ADC Resolution The ADC supports 8-bit or 10-bit resolutions. The 8-bit selection is performed by setting the bit LOWRES in the TSADCC Mode Register. See Section 41.11.2 “TSADCC Mode Register” on page 1029. By default, after a reset, the resolution is the highest and the DATA field in the “TSADCC Channel Data Register x (x = 0..7)” are fully used. 1012 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

By setting the bit LOWRES, the ADC switches in the lowest resolution and the conversion results can be read in the eight lowest significant bits of the data registers. The two highest bits of the DATA field in the corresponding TSADCC_CDR and of the LDATA field in the TSADCC_LCDR read 0. Moreover, when a PDC channel is connected to the TSADCC, 10-bit resolution sets the transfer request sizes to 16-bit. Setting the bit LOWRES automatically switches to 8-bit data transfers. In this case, the destination buffers are optimized. All the conversions for the Touchscreen forces the ADC in 10-bit resolution, regardless of the LOWRES setting. Further details are given in the section “Operating Modes” on page 1020. 41.6.2 ADC Clock The TSADCC uses the ADC Clock to perform conversions. Converting a single analog value to a 10-bit digital data requires Sample and Hold Clock cycles as defined in the field SHTIM of the “TSADCC Mode Register” and 10 ADC Clock cycles. The ADC Clock frequency is selected in the PRESCAL field of the “TSADCC Mode Register”. The ADC clock range is between MCK/2, if PRESCAL is 0, and MCK/128, if PRESCAL is set to 63 (0x3F). PRESCAL must be programmed in order to provide an ADC clock frequency according to the maximum sampling rate parameter given in the “Electrical Characteristics” section. 41.6.3 Sleep Mode The TSADCC Sleep Mode maximizes power saving by automatically deactivating the Analog-to-Digital Converter cell when it is not being used for conversions. Sleep Mode is enabled by setting the bit SLEEP in “TSADCC Mode Register”. The SLEEP of the ADC is automatically managed by the conversion sequencer, which can automatically process the conversions of all channels at lowest power consumption. When a trigger occurs, the Analog-to-Digital Converter cell is automatically activated. As the analog cell requires a start-up time, the logic waits during this time and then starts the conversion on the enabled channels. When all conversions are complete, the ADC is deactivated until the next trigger. 41.6.4 Startup Time The Touchscreen ADC has a minimal Startup Time when it exits the Sleep Mode. As the ADC Clock depends on the application, the user has to program the field STARTUP in the “TSADCC Mode Register”, which defines how many ADC Clock cycles to wait before performing the first conversion of the sequence. The field STARTUP can define a Startup Time between 8 and 1024 ADC Clock cycles by steps of 8. The user must assure that ADC Startup Time given in the section “Electrical Characteristics” is covered by this wait time. 41.6.5 Sample and Hold Time In the same way, a minimal Sample and Hold Time is necessary for the TSADCC to guarantee the best converted final value between selection of two channels. This time depends on the input impedance of the analog input, but also on the output impedance of the driver providing the signal to the analog input, as there is no input buffer amplifier. The Sample and Hold time has to be programmed through the bitfields SHTIM in the “TSADCC Mode Register” and TSSHTIM in the “TSADCC Touchscreen Register”. The field SHTIM defines the number of ADC Clock cycles for an analog input, while the field TSSHTIM defines the number of ADC Clock cycles for a Touchscreen input. These both fields can define a Sample and Hold time between 1 and 16 ADC Clock cycles. SAM9M11 [DATASHEET] 1013 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The field TSSHTIM defines also the time the power switches of the Touchscreen are closed when the TSADCC performs a conversion for the Touchscreen. 41.7 Touchscreen 41.7.1 Resistive Touchscreen Principles A resistive touchscreen is based on two resistive films, each one being fitted with a pair of electrodes, placed at the top and bottom on one film, and on the right and left on the other. Between the two, there is a layer that acts as an insulator, but also enables contact when you press the screen. This is illustrated in Figure 41-2. The TSADC controller has the ability to perform without external components:  Position Measurement  Pressure Measurement  Pen Detection Figure 41-2. Touchscreen Position Measurement Pen Contact X P YM YP X M VDD VDD X Y P P Y X P P Volt Volt X Y M M GND GND Vertical Position Detection Horizontal Position Detection 41.7.2 Position Measurement Method As shown in Figure 41-2, to detect the position of a contact, a supply is first applied from top to bottom. Due to the linear resistance of the film, there is a voltage gradient from top to bottom. When a contact is performed on the screen, the voltage propagates at the point the two surfaces come into contact with the second film. If the input impedance on the right and left electrodes sense is high enough, the film does not affect this voltage, despite its resistive nature. For the horizontal direction, the same method is used, but by applying supply from left to right. The range depends on the supply voltage and on the loss in the switches that connect to the top and bottom electrodes. In an ideal world (linear, with no loss through switches), the horizontal position is equal to: VY / VDD or VY / VDD. M P The proposed implementation with on-chip power switches is shown in Figure 41-3. The voltage measurement at the output of the switch compensates for the switches loss. 1014 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

It is possible to correct for the switch loss by performing the operation: [VY - VX ] / [VX - VX ]. P M P M This requires additional measurements, as shown in Figure 41-3. Figure 41-3. Touchscreen Switches Implementation XP VDDANA X M GND To the ADC Y P VDDANA Y M GND VDDANA VDDANA Switch Switch Resistor Resistor XP YP YP XP XM YM Switch Switch Resistor Resistor GND GND Horizontal Position Detection Vertical Position Detection SAM9M11 [DATASHEET] 1015 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.7.3 Pressure Measurement Method The method to measure the pressure (Rp) applied to the touchscreen is based on the knowledge of the X-Panel resistance (Rxp). Three conversions (Xpos,Z1,Z2) are necessary to determine the value of Rp (Zaxis resistance). Rp = Rxp*(Xpos/1024)*[(Z2/Z1)-1] VDDANA VDDANA VDDANA Switch Switch Switch Resistor Resistor Resistor Open circuit XP YP XP YP XP YP Rp Rp Rp XM YM XM YM XM YM Open Open Switch circuit Switch circuit Switch Resistor Resistor Resistor GND GND GND XPos Measure(Yp) Z1 Measure(Xp) Z2 Measure(Xp) 1016 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.7.4 Pen Detect Method When there is no contact, it is not necessary to perform conversion. However, it is important to detect a contact by keeping the power consumption as low as possible. The proposed implementation polarizes the vertical panel by closing the switch on X and ties the horizontal panel P by an embedded resistor connected to Y . This resistor is enabled by a fifth switch. Since there is no contact, no M current is flowing and there is no related power consumption. As soon as a contact occurs, a current is flowing in the touchscreen and a schmitt trigger detects the voltage in the resistor. The Touchscreen Interrupt configuration is entered by programming the bit PENDET in the “TSADCC Mode Register”. If this bit is written at 1, the switch on X and the switch on the resistor are both closed, except when a P touchscreen conversion is in progress. To complete the circuit, a programmable debouncer is placed at the output of the schmitt trigger. This debouncer is programmable at 1 ADC Clock period, useful when the system is running at Slow Clock, or at up to 215 ADC Clock periods, but better used to filter noise on the Touchscreen panel when the system is running at high speed. The debouncer length can be selected by programming the field PENDBC in “TSADCC Mode Register”. Figure 41-4. Touchscreen Pen Detect XP VDDANA X M GND To the ADC Y P VDDANA Y M GND PENDBC Debouncer Pen Interrupt GND The Touchscreen Pen Detect can be used to generate a TSADCC interrupt to wake up the system or it can be programmed to trig a conversion, so that a position can be measured as soon as a contact is detected if the TSADCC is programmed for an operating mode involving the Touchscreen. The Pen Detect generates two types of status, reported in the “TSADCC Status Register”:  the bit PENCNT is set as soon as a current flows for a time over the debouncing time as defined by PENDBC and remains set until TSADCC_SR is read.  the bit NOCNT is set as soon as no current flows for a time over the debouncing time as defined by PENDBC and remains set until TSADCC_SR is read. Both bits are automatically cleared as soon as the Status Register TSADCC_SR is read, and can generate an interrupt by writing accordingly the “TSADCC Interrupt Enable Register”. SAM9M11 [DATASHEET] 1017 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.8 Conversion Results When a conversion is completed, the resulting 8-bit or 10-bit digital value is right-aligned and stored in the “TSADCC Channel Data Register x (x = 0..7)” of the current channel and in the “TSADCC Last Converted Data Register”. The channel EOC bit and the bit DRDY in the “TSADCC Status Register” are both set. If the PDC channel is enabled, DRDY rising triggers a data transfer. In any case, either EOC and DRDY can trigger an interrupt. Reading one of the “TSADCC Channel Data Register x (x = 0..7)” registers clears the corresponding EOC bit. Reading “TSADCC Last Converted Data Register” clears the DRDY bit and the EOC bit corresponding to the last converted channel. Figure 41-5. EOCx and DRDY Flag Behavior W writiteh tSheT AARDTC =_ C1R Read the ADC_CDRx W writiteh tSheT AARDTC =_ C1R Read the ADC_LCDR CHx (ADC_CHSR) EOCx (ADC_SR) SHTIM Conversion SHTIM Conversion Time Time DRDY (ADC_SR) If the “TSADCC Channel Data Register x (x = 0..7)” is not read before further incoming data is converted, the corresponding Overrun Error (OVRE) flag is set in the “TSADCC Status Register”. In the same way, new data converted when DRDY is high sets the bit GOVRE (General Overrun Error) in the “TSADCC Status Register”. The OVRE and GOVRE flags are automatically cleared when the “TSADCC Status Register”is read. 1018 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 41-6. GOVRE and OVREx Flag Behavior Read ADC_SR ADTRG CH0 (ADC_CHSR) CH1 (ADC_CHSR) ADC_LCDR Undefined Data Data A Data B Data C ADC_CDR0 Undefined Data Data A Data C ADC_CDR1 Undefined Data Data B EOC0 SHTIM Conversion Read ADC_CDR0 (ADC_SR) SHTIM Conversion EOC1 SHTIM Conversion Read ADC_CDR1 (ADC_SR) GOVRE (ADC_SR) DRDY (ADC_SR) OVRE0 (ADC_SR) WARNING: If the corresponding channel is disabled during a conversion or if it is disabled and then reenabled during a conversion, its associated data and its corresponding EOC and OVRE flags in TSADCC_SR are unpredictable. 41.9 Conversion Triggers Conversions of the active analog channels are started with a software or a hardware trigger. The software trigger is provided by writing the “TSADCC Control Register” with the bit START at 1. The hardware trigger can be selected by the filed TRGMOD in the TSADCC Trigger Register (TSADCC_TRGR) between:  an edge, either rising or falling or any, detected on the external trigger pin TSADTRG  the Pen Detect, depending on how the PENDET bit is set in the “TSADCC Mode Register”  a continuous trigger, meaning the TSADCC restarts the next sequence as soon as it finishes the current one, in this case, only one software trigger is required at the beginning  a periodic trigger, which is defined by programming the field TRGPER in the “TSADCC Trigger Register” Enabling hardware triggers does not disable the software trigger functionality. Thus, if a hardware trigger is selected, the start of a conversion can still be initiated by the software trigger. SAM9M11 [DATASHEET] 1019 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.10 Operating Modes The Touchscreen ADC Controller features several operating modes, each defining a conversion sequence:  The ADC Mode: at each trigger, all the enabled channels are converted  The Touchscreen Mode: at each trigger, the touchscreen inputs are converted with the switches accordingly set and the results are processed and stored in the corresponding data registers  The Interleaved Mode: at each trigger, the 8 conversions for the touchscreen and the analog inputs conversions are performed. Only the analog inputs results are managed by the PDC and the touchscreen conversions can be performed less often than the analog inputs. The Operating Mode of the TSADCC is programmed in the field TSAMOD in the “TSADCC Mode Register”. The conversion sequences for each Operating Mode are described in the following paragraphs. The conversion sequencer, combined with the Sleep Modes, allows automatic processing with minimum processor intervention and optimized power consumption. In any case, the sequence starts with a trigger event. Note: The reference voltage pins always remain connected in normal mode as in sleep mode. 41.10.1 ADC Mode In the ADC Mode, the active channels are defined by the “TSADCC Channel Status Register”, which is defined by writing the “TSADCC Channel Enable Register” and “TSADCC Channel Disable Register”. The results are stored in the “TSADCC Channel Data Register x (x = 0..7)” and in the “TSADCC Last Converted Data Register”, so that data transfers by using the PDC are possible. At each trigger, the following sequence is performed: 1. If SLEEP is set, wake up the ADC cell and wait for the Startup Time. 2. If Channel 0 is enabled, convert Channel 0 and store result in both TSADCC_CDR0 and TSADCC_LCDR. 3. If Channel 1 is enabled, convert Channel 1 and store result in both TSADCC_CDR1 and TSADCC_LCDR. 4. If Channel 2 is enabled, convert Channel 2 and store result in both TSADCC_CDR2 and TSADCC_LCDR. 5. If Channel 3 is enabled, convert Channel 3 and store result in both TSADCC_CDR3 and TSADCC_LCDR. 6. If Channel 4 to Channel 7 are enabled, convert the Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. 7. If SLEEP is set, sleep down the ADC cell. If the PDC is enabled, all the converted data are transferred contiguously in the memory buffer. The bit LOWRES defines which resolution is used, either 8-bit or 10-bit, and thus the width of the PDC memory buffer. 1020 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.10.2 Touchscreen Mode Writing TSAMOD to “Touchscreen Only Mode” automatically enables the touchscreen pins as analog inputs, and thus disables the digital function of the corresponding pins. In Touchscreen Mode, the channels 0 to 3 corresponding to the Touchscreen inputs are automatically activated and the bits CH0 to CH3 are automatically set in the “TSADCC Channel Status Register”. The remaining channels can be either enabled or disabled by the user and their conversions are performed at the end of each touchscreen sequence. The resolution is forced to 10 bits, regardless of the LOWRES bit setting. At each trigger, if the bit PRES in “TSADCC Mode Register” is disabled, the following sequence is performed to measure only position. 1. If SLEEP is set, wake up the ADC cell and wait for the Startup Time. 2. Close the switches on the inputs X and X during the Sample and Hold Time. P M 3. Convert Channel X and store the result in TSADCC_CDR1. M 4. Close the switches on the inputs X and X during the Sample and Hold Time. P M 5. Convert Channel X , subtract TSADCC_CDR1 from the result and store the subtraction result in both P TSADCC_CDR0 and TSADCC_LCDR. 6. Close the switches on the inputs X and X during the Sample and Hold Time. P M 7. Convert Channel Y , subtract TSADCC_CDR1 from the result and store the subtraction result in both P TSADCC_CDR1 and TSADCC_LCDR. 8. Close the switches on the inputs Y and Y during the Sample and Hold Time. P M 9. Convert Channel Y and store the result in TSADCC_CDR3. M 10. Close the switches on the inputs Y and Y during the Sample and Hold Time. P M 11. Convert Channel Y , subtract TSADCC_CDR3 from the result and store the subtraction result in both P TSADCC_CDR2 and TSADCC_LCDR. 12. Close the switches on the inputs Y and Y during the Sample and Hold Time. P M 13. Convert Channel X , subtract TSADCC_CDR3 from the result and store the subtraction result in both P TSADCC_CDR3 and TSADCC_LCDR. 14. If Channel 4 to Channel 7 are enabled, convert the Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. 15. If SLEEP is set, sleep down the ADC cell. The resulting buffer is 16 bits wide and its structure stored in memory is: 1. X - X P M 2. Y - X P M 3. Y - Y P M 4. X - Y P M 5. AD4 to AD7 if enabled. The vertical position can be easily calculated by dividing the data at offset 0 (X - X ) by the data at offset 1 (Y - P M P X ). M The horizontal position can be easily calculated by dividing the data at offset 2 (Y - Y ) by the data at offset 3 (X P M P - Y ). M SAM9M11 [DATASHEET] 1021 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

If the bit PRES in “TSADCC Mode Register” is enabled, the following sequence is performed to measure both position and pressure. 1. If SLEEP is set, wake up the ADC cell and wait for the Startup Time. 2. Close the switches on the inputs X and Y during the Sample and Hold Time. M p 3. Convert Channel X and store the result in both TSADCC_Z1DR and TSADCC_LCDR. p 4. Close the switches on the inputs X and Y during the Sample and Hold Time. M P 5. Convert Channel Y and store the result in both TSADCC_Z2DR and TSADCC_LCDR. M 6. Close the switches on the inputs X and X during the Sample and Hold Time. P M 7. Convert Channel X and store the result in TSADCC_CDR1. M 8. Close the switches on the inputs X and X during the Sample and Hold Time. P M 9. Convert Channel X subtract TSADCC_CDR1 from the result and store the subtraction result in both p, TSADCC_CDR0 and TSADCC_LCDR. 10. Close the switches on the inputs X and X during the Sample and Hold Time. P M 11. Convert Channel Y and store the result in TSADCC_XPDR, subtract TSADCC_CDR1 from the result and P store the subtraction result in both TSADCC_CDR1 and TSADCC_LCDR. 12. Close the switches on the inputs Y and Y during the Sample and Hold Time. P M 13. Convert Channel Y and store the result in TSADCC_CDR3 while storing content of TSADCC_XPDR in M TSADCC_LCDR. 14. Close the switches on the inputs Y and Y during the Sample and Hold Time. P M 15. Convert Channel Y subtract TSADCC_CDR3 from the result and store the subtraction result in both p TSADCC_CDR2 and TSADCC_LCDR. 16. Close the switches on the inputs Y and Y during the Sample and Hold Time. P M 17. Convert Channel X subtract TSADCC_CDR3 from the result and store the subtraction result in both p TSADCC_CDR3 and TSADCC_LCDR. 18. if Channel 4 to channel 7are enabled, convert the channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR 19. If SLEEP is set, sleep down the ADC cell. The resulting buffer is 16 bits wide and its structure stored in memory is: 1. Z1 2. Z2 3. X - X P M 4. Y - X P M 5. Xpos 6. Y - Y P M 7. X - Y P M 8. AD4 to AD7 if enabled. The vertical position can be easily calculated by dividing the data at offset 2 (X - X ) by the data at offset 3(Y - P M P X ). M The horizontal position can be easily calculated by dividing the data at offset 5 (Y - Y ) by the data at offset 7 (X P M P - Y ). M The Pressure measure can be calculated using the following formula Rp = Rxp*(Xpos/1024)*[(Z2/Z1)-1] 1022 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.10.3 Interleaved Mode In the Interleaved Mode, the conversion of the touchscreen channels are made in parallel to each channel. In addition to interleaving, the analog channels 4 and 5 can be converted more often than the touchscreen channels depending on the TSFREQ field in the register TSADCC_MR. In the interleaved mode at least one ADC channel must be enabled. In the Interleaved Mode, the channels 0 to 3 corresponding to the Touchscreen inputs are automatically activated and the bits CH0 to CH3 are automatically set in the “TSADCC Channel Status Register”. This mode allows periodic conversion of the remaining channels at high sampling rate and converted data transferred in memory with the PDC while the touchscreen conversions are performed at low rate. The PDC transfers only analog channel data and touchscreen data must be read in the “TSADCC Channel Data Register x (x = 0..7)”. The resolution can be configured for the channel 4 to 7 only, through the LOWRES bit. The resolution for the conversion made on channels 0 to 3 is forced to 10 bits. At each trigger, the sequence performed depends on a Trigger Counter, which is compared at the end to the Touchscreen Frequency, as defined by the field TSFREQ in the register TSADCC_MR: Touchscreen Frequency = Trigger Frequency / (2TSFREQ+1) unless TSFREQ is programmed at 0 or 1. In such cases, the Touchscreen Frequency is one-sixth of the Trigger Frequency. As TSFREQ varies between 0 and 15, this results in the ADC channels being converted between 6 to 65536 less often than the Touchscreen channels. If the bit PRES in “TSADCC Mode Register” is disabled (measure only position), the sequences are as follow:  For Trigger Counter at 0: 1. Close the switches on the inputs X and X during the Sample and Hold Time. P M 2. Convert Channel X and store the result in TSADCC_CDR1. M 3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. 4. Set Trigger Counter to 1.  For Trigger Counter at 1: 1. Close the switches on the inputs X and X during the Sample and Hold Time. P M 2. Convert Channel X , subtract TSADCC_CDR1 from the result and store the subtraction result in P TSADCC_CDR0 (and also in TSADCC_LCDR if PDCEN is enabled). 3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. 4. Set Trigger Counter to 2.  For Trigger Counter at 2: 1. Close the switches on the inputs X and X during the Sample and Hold Time. P M 2. Convert Channel Y , subtract TSADCC_CDR1 from the result and store the subtraction result in P TSADCC_CDR1 (and also in TSADCC_LCDR if PDCEN is enabled). 3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. 4. Set Trigger Counter to 3. SAM9M11 [DATASHEET] 1023 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

 For Trigger Counter at 3: 1. Close the switches on the inputs Y and Y during the Sample and Hold Time. P M 2. Convert Channel Y and store the result in TSADCC_CDR3. M 3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. 4. Set Trigger Counter to 4.  For Trigger Counter at 4: 1. Close the switches on the inputs Y and Y during the Sample and Hold Time. P M 2. Convert Channel Y , subtract TSADCC_CDR3 from the result and store the subtraction result in P TSADCC_CDR2 (and also in TSADCC_LCDR if PDCEN is enabled). 3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. 4. Set Trigger Counter to 5.  For Trigger Counter at 5: 1. Close the switches on the inputs Y and Y during the Sample and Hold Time P M 2. Convert Channel X , subtract TSADCC_CDR3 from the result and store the subtraction result in P TSADCC_CDR3 (and also in TSADCC_LCDR if PDCEN is enabled). 3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. 4. Set Trigger Counter to 6.  For Trigger Counter between 6 and (2TSFREQ+1): 1. Increment Trigger Counter. 2. If Trigger Counter equals (2TSFREQ+1), then set Trigger Counter to 0. 3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. If the bit PRES in “TSADCC Mode Register” is enabled (measure both position and pressure), the sequences are as follow:  For Trigger Counter at 0: 1. Close the switches on the inputs X and Y during the Sample and Hold Time. P M 2. Convert Channel X and store the result in TSADCC_Z1DR (and also in TSADCC_LCDR if PDCEN is P enabled). 3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. 4. Set Trigger Counter to 1.  For Trigger Counter at 1: 1. Close the switches on the inputs X and Y during the Sample and Hold Time. P M 2. Convert Channel Y and store the result in TSADCC_Z2DR (and also in TSADCC_LCDR if PDCEN is M enabled). 3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. 4. Set Trigger Counter to 2. 1024 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

 For Trigger Counter at 2: 1. Close the switches on the inputs X and X during the Sample and Hold Time. P M 2. Convert Channel X and store the result in TSADCC_CDR1. M 3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. 4. Set Trigger Counter to 3.  For Trigger Counter at 3: 1. Close the switches on the inputs X and X during the Sample and Hold Time. P M 2. Convert Channel X , subtract TSADCC_CDR1 from the result and store the subtraction result in P TSADCC_CDR0 (and also in TSADCC_LCDR if PDCEN is enabled). 3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. 4. Set Trigger Counter to 4.  For Trigger Counter at 4: 1. Close the switches on the inputs X and X during the Sample and Hold Time. P M 2. Convert Channel Y and store the result in TSADCC_XPDR, subtract TSADCC_CDR1 from the result and P store the subtraction result in TSADCC_CDR1 (and also in TSADCC_LCDR if PDCEN is enabled). 3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. 4. Set Trigger Counter to 5.  For Trigger Counter at 5: 1. Close the switches on the inputs Y and Y during the Sample and Hold Time. P M 2. Convert Channel Y and store the result in TSADCC_CDR3 (and store content of TSADCC_XPDR in M TSADCC_LCDR if PDCEN is enabled). 3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. 4. Set Trigger Counter to 6.  For Trigger Counter at 6: 1. Close the switches on the inputs Y and Y during the Sample and Hold Time. P M 2. Convert Channel Y , subtract TSADCC_CDR3 from the result and store the subtraction result in P TSADCC_CDR2 (and also in TSADCC_LCDR if PDCEN is enabled). 3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. 4. Set Trigger Counter to 7.  For Trigger Counter at 7: 1. Close the switches on the inputs Y and Y during the Sample and Hold Time P M 2. Convert Channel X , subtract TSADCC_CDR3 from the result and store the subtraction result in P TSADCC_CDR3 (and also in TSADCC_LCDR if PDCEN is enabled). 3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. 4. Set Trigger Counter to 8. SAM9M11 [DATASHEET] 1025 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

 For Trigger Counter between 8 and (2TSFREQ+1): 1. Increment Trigger Counter. 2. If Trigger Counter equals (2TSFREQ+1), then set Trigger Counter to 0. 3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corresponding TSADCC_CDRx and TSADCC_LCDR. The Trigger Counter is cleared when TSAMOD is written to define the Interleaved Mode, then it simply rolls over. 41.10.4 Manual Mode The TSADCC features a manual mode allowing to control the state (open/close) of the four switches. Writing TSAMOD to “Manual Mode” automatically enables the ADC pins as analog inputs.The switches positions are controlled through the “TSADCC Manual Switch Command Register”. In this mode, the “Sample and Hold Time” used is the one defined for the Touchscreen mode (TSSHTIM). To perform a measurement, the following sequence must be followed 1. Select the switch (switches) to close. 2. If SLEEP is set, wake up the ADC cell and wait for the Startup Time. 3. Enable the Channel to convert and start a conversion. If SLEEP is set, wake up the ADC cell and wait for the Startup Time are performed before the conversion.The result is stored in TSADCC_CDRx (and TSADCC_LCDR if PDCEN is enabled). 4. If SLEEP is set, sleep down the ADC cell. 5. Open the switches to reduce power consumption. 1026 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11 Touchscreen ADC Controller (TSADCC) User Interface Table 41-4. Register Mapping Offset Register Name Access Reset 0x00 Control Register TSADCC_CR Write-only – 0x04 Mode Register TSADCC_MR Read/Write 0x0000_0000 0x08 Trigger Register TSADCC_TRGR Read/Write 0x0000_0000 0x0C Touchscreen Register TSADCC_TSR Read/Write 0x0000_0000 0x10 Channel Enable Register TSADCC_CHER Write-only – 0x14 Channel Disable Register TSADCC_CHDR Write-only – 0x18 Channel Status Register TSADCC_CHSR Read-only 0x0000_0000 0x1C Status Register TSADCC_SR Read-only 0x000C_0000 0x20 Last Converted Data Register TSADCC_LCDR Read-only 0x0000_0000 0x24 Interrupt Enable Register TSADCC_IER Write-only – 0x28 Interrupt Disable Register TSADCC_IDR Write-only – 0x2C Interrupt Mask Register TSADCC_IMR Read-only 0x0000_0000 0x30 Channel Data Register 0 TSADCC_CDR0 Read-only 0x0000_0000 0x34 Channel Data Register 1 TSADCC_CDR1 Read-only 0x0000_0000 0x38 Channel Data Register 2 TSADCC_CDR2 Read-only 0x0000_0000 0x3C Channel Data Register 3 TSADCC_CDR3 Read-only 0x0000_0000 0x40 Channel Data Register 4 TSADCC_CDR4 Read-only 0x0000_0000 0x44 Channel Data Register 5 TSADCC_CDR5 Read-only 0x0000_0000 0x48 Channel Data Register 6 TSADCC_CDR6 Read-only 0x0000_0000 0x4C Channel Data Register 7 TSADCC_CDR7 Read-only 0x0000_0000 0x50 X Position Data Register TSADCC_XPDR Read-only 0x0000_0000 0x54 Z1 Data Register TSADCC_Z1DR Read-only 0x0000_0000 0x58 Z2 Data Register TSADCC_Z2DR Read-only 0x0000_0000 0X5C Reserved – – – 0X60 Manual Switch Command Register TSADCC_MSCR Read/Write 0x0000_0000 0x64–0xE0 Reserved – – – 0xE4 Write Protection Mode Register TSADCC_WPMR Read/Write 0x0000_0000 0xE8 Write Protection Status Register TSADCC_WPSR Write-only – SAM9M11 [DATASHEET] 1027 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.1 TSADCC Control Register Name: TSADCC_CR Address: 0xFFFB0000 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – START SWRST • SWRST: Software Reset 0: No effect. 1: Resets the TSADCC simulating a hardware reset. • START: Start Conversion 0: No effect. 1: Begins analog-to-digital conversion. 1028 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.2 TSADCC Mode Register Name: TSADCC_MR Address: 0xFFFB0004 Access: Read/Write 31 30 29 28 27 26 25 24 PENDBC SHTIM 23 22 21 20 19 18 17 16 – STARTUP 15 14 13 12 11 10 9 8 PRESCAL 7 6 5 4 3 2 1 0 PRES PENDET SLEEP LOWRES PDCEN - TSAMOD • TSAMOD: Touchscreen ADC Mode TSAMOD Touchscreen ADC Operating Mode 0 ADC Mode 1 Touchscreen Only Mode 2 Interleaved Mode 3 Manual Mode • PDCEN: PDC transfer in Touchscreen/Interleaved mode or Manual mode 0: Disable the PDC transfer in Touchscreen/Interleaved mode or Manual mode 1: In Touchscreen/Interleaved mode or Manual mode, the data conversion is transferred in the TSADCC_LCDR allowing PDC transfer to memory. • LOWRES: Resolution Selection LOWRES Selected Resolution 0 10-bit resolution 1 8-bit resolution This option is only valid in ADC mode. • SLEEP: Sleep Mode SLEEP Selected Mode 0 Normal Mode 1 Sleep Mode • PRESCAL: Prescaler Rate Selection ADCCLK = MCK / ( (PRESCAL+1) * 2 ) • PENDET: Pen Detect Selection 0: Disable the Touchscreen pins as analog inputs 1: enable the Touchscreen pins as analog inputs SAM9M11 [DATASHEET] 1029 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• PRES: Pressure Measurement Selection 0: Disable the pressure measurement function 1: enable the pressure measurement function • STARTUP: Start Up Time Startup Time = (STARTUP+1) * 8/ADCCLK • SHTIM: Sample & Hold Time for ADC Channels Programming 0 for SHTIM gives a Sample & Hold Time equal to 1/ADCCLK. Sample & Hold Time = SHTIM/ADCCLK • PENDBC: Pen Detect debouncing period Period = 2PENDBC/ADCCLK 1030 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.3 TSADCC Trigger Register Name: TSADCC_TRGR Address: 0xFFFB0008 Access: Read/Write 31 30 29 28 27 26 25 24 TRGPER 23 22 21 20 19 18 17 16 TRGPER 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – TRGMOD • TRGMOD: Trigger Mode TRGMOD Selected Trigger Mode 0 0 0 No trigger, only software trigger can start conversions 0 0 1 External Trigger Rising Edge 0 1 0 External Trigger Falling Edge 0 1 1 External Trigger Any Edge 1 0 0 Pen Detect Trigger (shall be selected only if PENDET is set and TSAMOD = Touchscreen only mode) 1 0 1 Periodic Trigger (TRGPER shall be initiated appropriately) 1 1 0 Continuous Mode 1 1 1 Reserved • TRGPER: Trigger Period Effective only if TRGMOD defines a Periodic Trigger Defines the periodic trigger period, with the following equations: Trigger Period = (TRGPER+1) /ADCCLK SAM9M11 [DATASHEET] 1031 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.4 TSADCC Touchscreen Register Name: TSADCC_TSR Address: 0xFFFB000C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – TSSHTIM 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – TSFREQ • TSFREQ: Touchscreen Frequency in Interleaved Mode Effective only if the Touchscreen Interleaved Mode is selected. Defines the Touchscreen Frequency compared to the Trig- ger Frequency. If TSFREQ is 0 or 1, the Touchscreen Frequency is a sixth of the Trigger Frequency. Otherwise: Touchscreen Frequency = Trigger Frequency / (2TSFREQ+1) • TSSHTIM: Sample & Hold Time for Touchscreen Channels Programming 0 for TSSHTIM gives a Touchscreen Sample & Hold Time equal to 1/ADCCLK. Touchscreen Sample & Hold Time = TSSHTIM/ADCCLK 1032 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.5 TSADCC Channel Enable Register Name: TSADCC_CHER Address: 0xFFFB0010 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 CH7 CH6 CH5 CH4 CH3 CH2 CH1 CH0 • CHx: Channel x Enable 0: No effect. 1: Enables the corresponding channel. SAM9M11 [DATASHEET] 1033 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.6 TSADCC Channel Disable Register Name: TSADCC_CHDR Address: 0xFFFB0014 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 CH7 CH6 CH5 CH4 CH3 CH2 CH1 CH0 • CHx: Channel x Disable 0: No effect. 1: Disables the corresponding channel. Warning: If the corresponding channel is disabled during a conversion or if it is disabled then reenabled during a conver- sion, its associated data and its corresponding EOC and OVRE flags in TSADCC_SR are unpredictable. 1034 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.7 TSADCC Channel Status Register Name: TSADCC_CHSR Address: 0xFFFB0018 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 CH7 CH6 CH5 CH4 CH3 CH2 CH1 CH0 • CHx: Channel x Status 0: Corresponding channel is disabled. 1: Corresponding channel is enabled. SAM9M11 [DATASHEET] 1035 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.8 TSADCC Status Register Name: TSADCC_SR Address: 0xFFFB001C Access: Read-only 31 30 29 28 27 26 25 24 – OVREZ2 OVREZ1 OVREXP – EOCZ2 EOCZ1 EOCXP 23 22 21 20 19 18 17 16 – – NOCNT PENCNT RXBUFF ENDRX GOVRE DRDY 15 14 13 12 11 10 9 8 OVRE7 OVRE6 OVRE5 OVRE4 OVRE3 OVRE2 OVRE1 OVRE0 7 6 5 4 3 2 1 0 EOC7 EOC6 EOC5 EOC4 EOC3 EOC2 EOC1 EOC0 • EOCx: End of Conversion x 0: Corresponding analog channel is disabled, or the conversion is not finished. 1: Corresponding analog channel is enabled and conversion is complete. • OVREx: Overrun Error x 0: No overrun error on the corresponding channel since the last read of TSADCC_SR. 1: There has been an overrun error on the corresponding channel since the last read of TSADCC_SR. • DRDY: Data Ready 0: No data has been converted since the last read of TSADCC_LCDR. 1: At least one data has been converted and is available in TSADCC_LCDR. • GOVRE: General Overrun Error 0: No General Overrun Error occurred since the last read of TSADCC_SR. 1: At least one General Overrun Error has occurred since the last read of TSADCC_SR. • ENDRX: End of RX Buffer 0: The Receive Counter Register has not reached 0 since the last write in TSADCC_RCR or TSADCC_RNCR. 1: The Receive Counter Register has reached 0 since the last write in TSADCC_RCR or TSADCC_RNCR. • RXBUFF: RX Buffer Full 0: TSADCC_RCR or TSADCC_RNCR have a value other than 0. 1: Both TSADCC_RCR and TSADCC_RNCR have a value of 0. • PENCNT: Pen Contact 0: No contact has been detected since the last read of TSADCC_SR or PENDET is at 0. 1: At least one contact has been detected since the last read of TSADCC_SR. • NOCNT: No Contact 0: No contact loss has been detected since the last read of TSADCC_SR or PENDET is at 0. 1: At least one contact loss has been detected since the last read of TSADCC_SR. 1036 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• EOCXp: End of Conversion X Position 0: The pressure measurement is disabled or the Xp conversion is not finished. 1: The pressure measurement is enabled and the Xp conversion is complete • EOCZ1: End of Conversion Z1 Measure 0: The pressure measurement is disabled or the Z1 conversion is not finished. 1: The pressure measurement is enabled and the Z1 conversion is complete • EOCZ2: End of Conversion Z2 Measure 0: The pressure measurement is disabled or the Z2 conversion is not finished. 1: The pressure measurement is enabled and the Z2 conversion is complete • OVREXP: Overrun Error on X Position 0: No overrun error on the XP measure channel. 1: There has been an overrun error on the XP measure channel. • OVREZ1: Overrun Error on Z1 Measure 0: No overrun error on the Z1 measure channel. 1: There has been an overrun error on the Z1 measure channel. • OVREZ2: Overrun Error on Z2 Measure 0: No overrun error on the Z2 measure channel. 1: There has been an overrun error on the Z2 measure channel. SAM9M11 [DATASHEET] 1037 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.9 TSADCC Channel Data Register x (x = 0..7) Name: TSADCC_CDR0..TSADCC_CDR7 Address: 0xFFFB0030 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – DATA 7 6 5 4 3 2 1 0 DATA • DATA: Channel Data The analog-to-digital conversion data is placed into this register at the end of a conversion of the corresponding channel and remains until a new conversion on the same channel is completed. 1038 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.10 TSADCC Last Converted Data Register Name: TSADCC_LCDR Address: 0xFFFB0020 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – LDATA 7 6 5 4 3 2 1 0 LDATA • LDATA: Last Data Converted The analog-to-digital conversion data is placed into this register at the end of a conversion on any analog channel and remains until a new conversion on any analog channel is completed. SAM9M11 [DATASHEET] 1039 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.11 TSADCC Interrupt Enable Register Name: TSADCC_IER Address: 0xFFFB0024 Access: Write-only 31 30 29 28 27 26 25 24 – OVREZ2 OVREZ1 OVREXP – EOCZ2 EOCZ1 EOCXP 23 22 21 20 19 18 17 16 – – NOCNT PENCNT RXBUFF ENDRX GOVRE DRDY 15 14 13 12 11 10 9 8 OVRE7 OVRE6 OVRE5 OVRE4 OVRE3 OVRE2 OVRE1 OVRE0 7 6 5 4 3 2 1 0 EOC7 EOC6 EOC5 EOC4 EOC3 EOC2 EOC1 EOC0 • EOCx: End of Conversion Interrupt Enable x • OVREx: Overrun Error Interrupt Enable x • DRDY: Data Ready Interrupt Enable • GOVRE: General Overrun Error Interrupt Enable • ENDRX: End of Receive Buffer Interrupt Enable • RXBUFF: Receive Buffer Full Interrupt Enable • PENCNT: Pen Contact • NOCNT: No Contact • EOCXp: End of Conversion X Position • EOCZ1: End of Conversion Z1 Measure • EOCZ2: End of Conversion Z2 Measure • OVREXP: Overrun Error Interrupt Enable X Position • OVREZ1: Overrun Error Interrupt Enable Z1 Measure • OVREZ2: Overrun Error Interrupt Enable Z2 Measure 0: No effect. 1: Enables the corresponding interrupt. 1040 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.12 TSADCC Interrupt Disable Register Name: TSADCC_IDR Address: 0xFFFB0028 Access: Write-only 31 30 29 28 27 26 25 24 – OVREZ2 OVREZ1 OVREXP – EOCZ2 EOCZ1 EOCXP 23 22 21 20 19 18 17 16 – – NOCNT PENCNT RXBUFF ENDRX GOVRE DRDY 15 14 13 12 11 10 9 8 OVRE7 OVRE6 OVRE5 OVRE4 OVRE3 OVRE2 OVRE1 OVRE0 7 6 5 4 3 2 1 0 EOC7 EOC6 EOC5 EOC4 EOC3 EOC2 EOC1 EOC0 • EOCx: End of Conversion Interrupt Disable x • OVREx: Overrun Error Interrupt Disable x • DRDY: Data Ready Interrupt Disable • GOVRE: General Overrun Error Interrupt Disable • ENDRX: End of Receive Buffer Interrupt Disable • RXBUFF: Receive Buffer Full Interrupt Disable • PENCNT: Pen Contact • NOCNT: No Contact • EOCXp: End of Conversion X Position • EOCZ1: End of Conversion Z1 Measure • EOCZ2: End of Conversion Z2 Measure • OVREXP: Overrun Error Interrupt Disable X Position • OVREZ1: Overrun Error Interrupt Disable Z1 Measure • OVREZ2: Overrun Error Interrupt Disable Z2 Measure 0: No effect. 1: Disables the corresponding interrupt. SAM9M11 [DATASHEET] 1041 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.13 TSADCC Interrupt Mask Register Name: TSADCC_IMR Address: 0xFFFB002C Access: Read-only 31 30 29 28 27 26 25 24 – OVREZ2 OVREZ1 OVREXP – EOCZ2 EOCZ1 EOCXP 23 22 21 20 19 18 17 16 – – NOCNT PENCNT RXBUFF ENDRX GOVRE DRDY 15 14 13 12 11 10 9 8 OVRE7 OVRE6 OVRE5 OVRE4 OVRE3 OVRE2 OVRE1 OVRE0 7 6 5 4 3 2 1 0 EOC7 EOC6 EOC5 EOC4 EOC3 EOC2 EOC1 EOC0 • EOCx: End of Conversion Interrupt Mask x • OVREx: Overrun Error Interrupt Mask x • DRDY: Data Ready Interrupt Mask • GOVRE: General Overrun Error Interrupt Mask • ENDRX: End of Receive Buffer Interrupt Mask • RXBUFF: Receive Buffer Full Interrupt Mask • PENCNT: Pen Contact • NOCNT: No Contact • EOCXp: End of Conversion X Position • EOCZ1: End of Conversion Z1 Measure • EOCZ2: End of Conversion Z2 Measure • OVREXP: Overrun Error Interrupt Mask X Position • OVREZ1: Overrun Error Interrupt Mask Z1 Measure • OVREZ2: Overrun Error Interrupt Mask Z2 Measure 0: The corresponding interrupt is disabled. 1: The corresponding interrupt is enabled. 1042 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.14 TSADCC X Position Data Register Name: TSADCC_XPDR Address: 0xFFFB0050 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – DATA 7 6 5 4 3 2 1 0 DATA • DATA: X Position Data SAM9M11 [DATASHEET] 1043 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.15 TSADCC Z1 Data Register Name: TSADCC_Z1DR Address: 0xFFFB0054 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – DATA 7 6 5 4 3 2 1 0 DATA • DATA: Z1 Measurement Data 1044 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.16 TSADCC Z2 Data Register Name: TSADCC_Z2DR Address: 0xFFFB0058 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – Z2 7 6 5 4 3 2 1 0 Z2 • DATA: Z2 Measurement Data SAM9M11 [DATASHEET] 1045 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.17 TSADCC Manual Switch Command Register Name: TSADCC_MSCR Address: 0xFFFB0060 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – 7 6 5 4 3 2 1 0 – – – – Y Y X X M P M P • Y Y X X : Switch Command M, P, M, P If bit is set the related switch is closed If bit is cleared the related switch is open 1046 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.18 TSADCC Write Protection Mode Register Name: TSADCC_WPMR Address: 0xFFFB00E4 Access: Read/Write 31 30 29 28 27 26 25 24 KEY 23 22 21 20 19 18 17 16 KEY 15 14 13 12 11 10 9 8 KEY 7 6 5 4 3 2 1 0 – – – – – – – WPEN • WPEN: Write Protection of TSADCC_MR, TSADCC_TRGR and TSADCC_TSR 0: Disables the write protection if KEY value corresponds to 0x545341 (“TSA” in ASCII). 1: Enables the write protection if KEY value corresponds to 0x545341 (“TSA” in ASCII). • KEY: Write Protection Key Value Name Description Writing any other value in this field aborts the write operation of the WPEN bit. 0x545341 PASSWD Always reads as 0. SAM9M11 [DATASHEET] 1047 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

41.11.19 TSADCC Write Protection Status Register Name: TSADCC_WPSR Address: 0xFFFB00E8 Access: Read/Write 31 30 29 28 27 26 25 24 OFFSET_ERR 23 22 21 20 19 18 17 16 OFFSET_ERR 15 14 13 12 11 10 9 8 OFFSET_ERR 7 6 5 4 3 2 1 0 – – – – – – – WPS • WPS: Write Protection Status 0: Write protection is disabled. 1: Write Protection is enabled. • OFFSET_ERR: Offset Error Offset where the last unauthorized access occurred. 1048 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42. AC97 Controller (AC97C) 42.1 Description The AC97 Controller is the hardware implementation of the AC97 digital controller (DC’97) compliant with AC97 Component Specification 2.2. The AC97 Controller communicates with an audio codec (AC97) or a modem codec (MC’97) via the AC-link digital serial interface. All digital audio, modem and handset data streams, as well as control (command/status) informations are transferred in accordance to the AC-link protocol. The AC97 Controller features a Peripheral DMA Controller (PDC) for audio streaming transfers. It also supports variable sampling rate and four Pulse Code Modulation (PCM) sample resolutions of 10, 16, 18 and 20 bits. 42.2 Embedded Characteristics  Compatible with AC97 Component Specification V2.2  Capable to Interface with a Single Analog Front end  Three independent RX Channels and three independent TX Channels ̶ One RX and one TX channel dedicated to the AC97 Analog Front end control ̶ One RX and one TX channel for data transfers, associated with a PDC ̶ One RX and one TX channel for data transfers with no PDC  Time Slot Assigner allowing to assign up to 12 time slots to a channel  Channels support mono or stereo up to 20 bit sample length ̶ Variable sampling rate AC97 Codec Interface (48 kHz and below) SAM9M11 [DATASHEET] 1049 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.3 Block Diagram Figure 42-1. Functional Block Diagram MCK Clock Domain Slot Number SYNC AC97 Slot Controller Slot Number 16/20 bits Slot #0 Transmit Shift Register M AC97 Tag Controller Receive Shift Register Slot #0,1 U AC97 CODEC Channel SDATA_OUT X Transmit Shift Register AC97C_COTHR Slot #1,2 AC97C_CORHR Receive Shift Register Slot #2 SDATA_IN AC97 Channel A D Transmit Shift Register AC97C_CATHR Slot #3...12 E AC97C_CARHR Receive Shift Register BITCLK AC97C Interrupt M AC97 Channel B U AC97C_CBTHR Transmit Shift Register Slot #3...12 AC97C_CBRHR X Receive Shift Register MCK User Interface Bit Clock Domain APB Interface 1050 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.4 Pin Name List Table 42-1. I/O Lines Description Pin Name Pin Description Type AC97CK 12.288-MHz bit-rate clock Input AC97RX Receiver Data (Referred as SDATA_IN in AC-link spec) Input AC97FS 48-kHz frame indicator and synchronizer Output AC97TX Transmitter Data (Referred as SDATA_OUT in AC-link spec) Output The AC97 reset signal provided to the primary codec can be generated by a PIO. 42.5 Application Block Diagram Figure 42-2. Application Block diagram AC 97 Controller AC-link AC'97 Primary Codec AC97_RESET PIOx AC97_SYNC AC97FS AC97_BITCLK AC97CK AC97_SDATA_OUT AC97TX AC97_SDATA_IN AC97RX SAM9M11 [DATASHEET] 1051 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.6 Product Dependencies 42.6.1 I/O Lines The pins used for interfacing the compliant external devices may be multiplexed with PIO lines. Before using the AC97 Controller receiver, the PIO controller must be configured in order for the AC97C receiver I/O lines to be in AC97 Controller peripheral mode. Before using the AC97 Controller transmitter, the PIO controller must be configured in order for the AC97C transmitter I/O lines to be in AC97 Controller peripheral mode. Table 42-2. I/O Lines Instance Signal I/O Line Peripheral AC97C AC97CK PD9 A AC97C AC97FS PD8 A AC97C AC97RX PD6 A AC97C AC97TX PD7 A 42.6.2 Power Management The AC97 Controller is not continuously clocked. Its interface may be clocked through the Power Management Controller (PMC), therefore the programmer must first configure the PMC to enable the AC97 Controller clock. The AC97 Controller has two clock domains. The first one is supplied by PMC and is equal to MCK. The second one is AC97CK which is sent by the AC97 Codec (Bit clock). Signals that cross the two clock domains are re-synchronized. MCK clock frequency must be higher than the AC97CK (Bit Clock) clock frequency. 42.6.3 Interrupt The AC97 Controller interface has an interrupt line connected to the Advanced Interrupt Controller (AIC). Handling interrupts requires programming the AIC before configuring the AC97C. All AC97 Controller interrupts can be enabled/disabled by writing to the AC97 Controller Interrupt Enable/Disable Registers. Each pending and unmasked AC97 Controller interrupt will assert the interrupt line. The AC97 Controller interrupt service routine can get the interrupt source in two steps:  Reading and ANDing AC97 Controller Interrupt Mask Register (AC97C_IMR) and AC97 Controller Status Register (AC97C_SR).  Reading AC97 Controller Channel x Status Register (AC97C_CxSR). Table 42-3. Peripheral IDs Instance ID AC97C 24 1052 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.7 Functional Description 42.7.1 Protocol overview AC-link protocol is a bidirectional, fixed clock rate, serial digital stream. AC-link handles multiple input and output Pulse Code Modulation PCM audio streams, as well as control register accesses employing a Time Division Multiplexed (TDM) scheme that divides each audio frame in 12 outgoing and 12 incoming 20-bit wide data slots. Figure 42-3. Bidirectional AC-link Frame with Slot Assignment Slot # 0 1 2 3 4 5 6 7 8 9 10 11 12 AC97FS CMD CMD PCM PCM LINE 1 PCM PCM PCM PCM LINE 2 HSET IO AC97TX TAG ADDR DATA L Front R Front DAC Center L SURR R SURR LFE DAC DAC CTRL (Controller Output) STATUS STATUS PCM PCM LINE 1 PCM LINE 2 HSET IO AC97RX TAG ADDR DATA LEFT RIGHT DAC MIC RSVED RSVED RSVED ADC ADC STATUS (Codec output) Table 42-4. AC-link Output Slots Transmitted from the AC97C Controller Slot # Pin Description 0 TAG 1 Command Address Port 2 Command Data Port 3,4 PCM playback Left/Right Channel 5 Modem Line 1 Output Channel 6, 7, 8 PCM Center/Left Surround/Right Surround 9 PCM LFE DAC 10 Modem Line 2 Output Channel 11 Modem Handset Output Channel 12 Modem GPIO Control Channel Table 42-5. AC-link Input Slots Transmitted from the AC97C Controller Slot # Pin Description 0 TAG 1 Status Address Port 2 Status Data Port 3,4 PCM playback Left/Right Channel 5 Modem Line 1 ADC 6 Dedicated Microphone ADC 7, 8, 9 Vendor Reserved 10 Modem Line 2 ADC 11 Modem Handset Input ADC 12 Modem IO Status SAM9M11 [DATASHEET] 1053 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.7.2 Slot Description 42.7.2.1 Tag Slot The tag slot, or slot 0, is a 16-bit wide slot that always goes at the beginning of an outgoing or incoming frame. Within tag slot, the first bit is a global bit that flags the entire frame validity. The next 12 bit positions sampled by the AC97 Controller indicate which of the corresponding 12 time slots contain valid data. The slot’s last two bits (combined) called Codec ID, are used to distinguish primary and secondary codec. The 16-bit wide tag slot of the output frame is automatically generated by the AC97 Controller according to the transmit request of each channel and to the SLOTREQ from the previous input frame, sent by the AC97 Codec, in Variable Sample Rate mode. 42.7.2.2 Codec Slot 1 The command/status slot is a 20-bit wide slot used to control features, and monitors status for AC97 Codec functions. The control interface architecture supports up to sixty-four 16-bit wide read-write registers. Only the even registers are currently defined and addressed. Slot 1’s bitmap is the following:  Bit 19 is for read-write command, 1 = read, 0 = write.  Bits [18:12] are for control register index.  Bits [11:0] are reserved. 42.7.2.3 Codec Slot 2 Slot 2 is a 20-bit wide slot used to carry 16-bit wide AC97 Codec control register data. If the current command port operation is a read, the entire slot time is stuffed with zeros. Its bitmap is the following:  Bits [19:4] are the control register data  Bits [3:0] are reserved and stuffed with zeros. 42.7.2.4 Data Slots [3:12] Slots [3:12] are 20-bit wide data slots, they usually carry audio PCM and/or modem I/O data. 1054 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.7.3 AC97 Controller Channel Organization The AC97 Controller features a Codec channel and 2 logical channels: Channel A, Channel B. The Codec channel controls AC97 Codec registers, it enables write and read configuration values in order to bring the AC97 Codec to an operating state. The Codec channel always runs slot 1 and slot 2 exclusively, in both input and output directions. Channel A, Channel B transfer data to/from AC97 codec. All audio samples and modem data must transit by these 2 channels. However, Channels A and B are connected to PDC channels thus making it suitable for audio streaming applications. Each slot of the input or the output frame that belongs to this range [3 to 12] can be operated by Channel A or Channel B. The slot to channel assignment is configured by two registers:  AC97 Controller Input Channel Assignment Register (AC97C_ICA)  AC97 Controller Output Channel Assignment Register (AC97C_OCA) The AC97 Controller Input Channel Assignment Register (AC97C_ICA) configures the input slot to channel assignment. The AC97 Controller Output Channel Assignment Register (AC97C_OCA) configures the output slot to channel assignment. A slot can be left unassigned to a channel by the AC97 Controller. Slots 0, 1,and 2 cannot be assigned to Channel A or to Channel B through the AC97C_OCA and AC97C_ICA Registers. The width of sample data, that transit via the Channel varies and can take one of these values; 10, 16, 18 or 20 bits. Figure 42-4. Logical Channel Assignment Slot # 0 1 2 3 4 5 6 7 8 9 10 11 12 AC97FS AC97TX CMD CMD PCM PCM LINE 1 PCM PCM PCM PCM LINE 2 HSET IO TAG (Controller Output) ADDR DATA L Front R Front DAC Center L SURR R SURR LFE DAC DAC CTRL Codec Channel Channel A AC97C_OCA = 0x0000_0209 AC97RX STATUS STATUS PCM PCM LINE 1 PCM LINE 2 HSET IO (Codec output) TAG ADDR DATA LEFT RIGHT DAC MIC RSVED RSVED RSVED ADC ADC STATUS Codec Channel Channel A AC97C_ICA = 0x0000_0009 SAM9M11 [DATASHEET] 1055 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.7.3.1 AC97 Controller Setup The following operations must be performed in order to bring the AC97 Controller into an operating state: 1. Enable the AC97 Controller clock in the PMC controller. 2. Turn on AC97 function by enabling the ENA bit in AC97 Controller Mode Register (AC97C_MR). 3. Configure the input channel assignment by controlling the AC97 Controller Input Assignment Register (AC97C_ICA). 4. Configure the output channel assignment by controlling the AC97 Controller Input Assignment Register (AC97C_OCA). 5. Configure sample width for Channel A, Channel B by writing the SIZE bit field in AC97C Channel x Mode Register (AC97C_CAMR), (AC97C_CBMR). The application can write 10, 16, 18,or 20-bit wide PCM samples through the AC97 interface and they will be transferred into 20-bit wide slots. 6. Configure data Endianness for Channel A, Channel B by writing CEM bit field in (AC97C_CAMR), (AC97C_CBMR) register. Data on the AC-link are shifted MSB first. The application can write little- or big- endian data to the AC97 Controller interface. 7. Configure the PIO controller to drive the RESET signal of the external Codec. The RESET signal must fulfill external AC97 Codec timing requirements. 8. Enable Channel A and/or Channel B by writing CEN bit field in AC97C_CxMR. 42.7.3.2 Transmit Operation The application must perform the following steps in order to send data via a channel to the AC97 Codec:  Check if previous data has been sent by polling TXRDY flag in the AC97C Channel x Status Register (AC97_CxSR). x being one of the 2 channels.  Write data to the AC97 Controller Channel x Transmit Holding Register (AC97C_CxTHR). Once data has been transferred to the Channel x Shift Register, the TXRDY flag is automatically set by the AC97 Controller which allows the application to start a new write action. The application can also wait for an interrupt notice associated with TXRDY in order to send data. The interrupt remains active until TXRDY flag is cleared. Figure 42-5. Audio Transfer (PCM L Front, PCM R Front) on Channel x Slot # 0 1 2 3 4 5 6 7 8 9 10 11 12 AC97FS AC97TX CMD CMD PCM PCM LINE 1 PCM PCM PCM PCM LINE 2 HSET IO TAG (Controller Output) ADDR DATA L Front R Front DAC Center L SURR R SURR LFE DAC DAC CTRL TXRDYCx (AC97C_SR) TXEMPTY (AC97C_SR) Write access to AC97C_THRx PCM L Front transfered to the shift register PCM R Front transfered to the shift register The TXEMPTY flag in the AC97 Controller Channel x Status Register (AC97C_CxSR) is set when all requested transmissions for a channel have been shifted on the AC-link. The application can either poll TXEMPTY flag in AC97C_CxSR or wait for an interrupt notice associated with the same flag. 1056 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

In most cases, the AC97 Controller is embedded in chips that target audio player devices. In such cases, the AC97 Controller is exposed to heavy audio transfers. Using the polling technique increases processor overhead and may fail to keep the required pace under an operating system. In order to avoid these polling drawbacks, the application can perform audio streams by using PDC connected to channel A, which reduces processor overhead and increases performance especially under an operating system. The PDC transmit counter values must be equal to the number of PCM samples to be transmitted, each sample goes in one slot. 42.7.3.3 AC97 Output Frame The AC97 Controller outputs a thirteen-slot frame on the AC-Link. The first slot (tag slot or slot 0) flags the validity of the entire frame and the validity of each slot; whether a slot carries valid data or not. Slots 1 and 2 are used if the application performs control and status monitoring actions on AC97 Codec control/status registers. Slots [3:12] are used according to the content of the AC97 Controller Output Channel Assignment Register (AC97C_OCA). If the application performs many transmit requests on a channel, some of the slots associated to this channel or all of them will carry valid data. 42.7.3.4 Receive Operation The AC97 Controller can also receive data from AC97 Codec. Data is received in the channel’s shift register and then transferred to the AC97 Controller Channel x Read Holding Register. To read the newly received data, the application must perform the following steps:  Poll RXRDY flag in AC97 Controller Channel x Status Register (AC97C_CxSR). x being one of the 2 channels.  Read data from AC97 Controller Channel x Read Holding Register. The application can also wait for an interrupt notice in order to read data from AC97C_CxRHR. The interrupt remains active until RXRDY is cleared by reading AC97C_CxSR. The RXRDY flag in AC97C_CxSR is set automatically when data is received in the Channel x shift register. Data is then shifted to AC97C_CxRHR. Figure 42-6. Audio Transfer (PCM L Front, PCM R Front) on Channel x Slot # 0 1 2 3 4 5 6 7 8 9 10 11 12 AC97FS STATUS STATUS PCM PCM LINE 1 PCM LINE 2 HSET IO AC97RX TAG ADDR DATA LEFT RIGHT DAC MIC RSVED RSVED RSVED ADC ADC STATUS (Codec output) RXRDYCx (AC97C_SR) Read access to AC97C_RHRx If the previously received data has not been read by the application, the new data overwrites the data already waiting in AC97C_CxRHR, therefore the OVRUN flag in AC97C_CxSR is raised. The application can either poll the OVRUN flag in AC97C_CxSR or wait for an interrupt notice. The interrupt remains active until the OVRUN flag in AC97C_CxSR is set. The AC97 Controller can also be used in sound recording devices in association with an AC97 Codec. The AC97 Controller may also be exposed to heavy PCM transfers. The application can use the PDC connected to channel A in order to reduce processor overhead and increase performance especially under an operating system. The PDC receive counter values must be equal to the number of PCM samples to be received, each sample goes in one slot. SAM9M11 [DATASHEET] 1057 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.7.3.5 AC97 Input Frame The AC97 Controller receives a thirteen slot frame on the AC-Link sent by the AC97 Codec. The first slot (tag slot or slot 0) flags the validity of the entire frame and the validity of each slot; whether a slot carries valid data or not. Slots 1 and 2 are used if the application requires status informations from AC97 Codec. Slots [3:12] are used according to AC97 Controller Output Channel Assignment Register (AC97C_ICA) content. The AC97 Controller will not receive any data from any slot if AC97C_ICA is not assigned to a channel in input. 42.7.3.6 Configuring and Using Interrupts Instead of polling flags in AC97 Controller Global Status Register (AC97C_SR) and in AC97 Controller Channel x Status Register (AC97C_CxSR), the application can wait for an interrupt notice. The following steps show how to configure and use interrupts correctly:  Set the interruptible flag in AC97 Controller Channel x Mode Register (AC97C_CxMR).  Set the interruptible event and channel event in AC97 Controller Interrupt Enable Register (AC97C_IER). The interrupt handler must read both AC97 Controller Global Status Register (AC97C_SR) and AC97 Controller Interrupt Mask Register (AC97C_IMR) and AND them to get the real interrupt source. Furthermore, to get which event was activated, the interrupt handler has to read AC97 Controller Channel x Status Register (AC97C_CxSR), x being the channel whose event triggers the interrupt. The application can disable event interrupts by writing in AC97 Controller Interrupt Disable Register (AC97C_IDR). The AC97 Controller Interrupt Mask Register (AC97C_IMR) shows which event can trigger an interrupt and which one cannot. 42.7.3.7 Endianness Endianness can be managed automatically for each channel, except for the Codec channel, by writing to Channel Endianness Mode (CEM) in AC97C_CxMR. This enables transferring data on AC-link in Big Endian format without any additional operation. 42.7.3.8 To Transmit a Word Stored in Big Endian Format on AC-link Word to be written in AC97 Controller Channel x Transmit Holding Register (AC97C_CxTHR) (as it is stored in memory or microprocessor register). 31 24 23 16 15 8 7 0 Byte0[7:0] Byte1[7:0] Byte2[7:0] Byte3[7:0] Word stored in Channel x Transmit Holding Register (AC97C_CxTHR) (data to transmit). 31 24 23 20 19 16 15 8 7 0 – – Byte2[3:0] Byte1[7:0] Byte0[7:0] Data transmitted on appropriate slot: data[19:0] = {Byte2[3:0], Byte1[7:0], Byte0[7:0]}. 42.7.3.9 To Transmit A Halfword Stored in Big Indian Format on AC-link Halfword to be written in AC97 Controller Channel x Transmit Holding Register (AC97C_CxTHR). 31 24 23 16 15 8 7 0 – – Byte0[7:0] Byte1[7:0] Halfword stored in AC97 Controller Channel x Transmit Holding Register (AC97C_CxTHR) (data to transmit). 31 24 23 16 15 8 7 0 – – Byte1[7:0] Byte0[7:0] Data emitted on related slot: data[19:0] = {0x0, Byte1[7:0], Byte0[7:0]}. 1058 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.7.3.10 To Transmit a10-bit Sample Stored in Big Endian Format on AC-link Halfword to be written in AC97 Controller Channel x Transmit Holding Register (AC97C_CxTHR). 31 24 23 16 15 8 7 0 – – Byte0[7:0] {0x00, Byte1[1:0]} Halfword stored in AC97 Controller Channel x Transmit Holding Register (AC97C_CxTHR) (data to transmit). 31 24 23 16 15 10 9 8 7 0 Byte1 – – – Byte0[7:0] [1:0] Data emitted on related slot: data[19:0] = {0x000, Byte1[1:0], Byte0[7:0]}. 42.7.3.11 To Receive Word transfers Data received on appropriate slot: data[19:0] = {Byte2[3:0], Byte1[7:0], Byte0[7:0]}. Word stored in AC97 Controller Channel x Receive Holding Register (AC97C_CxRHR) (Received Data). 31 24 23 20 19 16 15 8 7 0 – – Byte2[3:0] Byte1[7:0] Byte0[7:0] Data is read from AC97 Controller Channel x Receive Holding Register (AC97C_CxRHR) when Channel x data size is greater than 16 bits and when big-endian mode is enabled (data written to memory). 31 24 23 16 15 8 7 0 Byte0[7:0] Byte1[7:0] {0x0, Byte2[3:0]} 0x00 42.7.3.12 To Receive Halfword Transfers Data received on appropriate slot: data[19:0] = {0x0, Byte1[7:0], Byte0[7:0]}. Halfword stored in AC97 Controller Channel x Receive Holding Register (AC97C_CxRHR) (Received Data). 31 24 23 16 15 8 7 0 – – Byte1[7:0] Byte0[7:0] Data is read from AC97 Controller Channel x Receive Holding Register (AC97C_CxRHR) when data size is equal to 16 bits and when big-endian mode is enabled. 31 24 23 16 15 8 7 0 – – Byte0[7:0] Byte1[7:0] 42.7.3.13 To Receive 10-bit Samples Data received on appropriate slot: data[19:0] = {0x000, Byte1[1:0], Byte0[7:0]}.Halfword stored in AC97 Controller Channel x Receive Holding Register (AC97C_CxRHR) (Received Data) 31 24 23 16 15 10 9 8 7 0 Byte1 – – – Byte0[7:0] [1:0] Data read from AC97 Controller Channel x Receive Holding Register (AC97C_CxRHR) when data size is equal to 10 bits and when big-endian mode is enabled. 31 24 23 16 15 8 7 3 1 0 Byte1 – – Byte0[7:0] 0x00 [1:0] SAM9M11 [DATASHEET] 1059 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.7.4 Variable Sample Rate The problem of variable sample rate can be summarized by a simple example. When passing a 44.1 kHz stream across the AC-link, for every 480 audio output frames that are sent across, 441 of them must contain valid sample data. The new AC97 standard approach calls for the addition of “on-demand” slot request flags. The AC97 Codec examines its sample rate control register, the state of its FIFOs, and the incoming SDATA_OUT tag bits (slot 0) of each output frame and then determines which SLOTREQ bits to set active (low). These bits are passed from the AC97 Codec to the AC97 Controller in slot 1/SLOTREQ in every audio input frame. Each time the AC97 controller sees one or more of the newly defined slot request flags set active (low) in a given audio input frame, it must pass along the next PCM sample for the corresponding slot(s) in the AC-link output frame that immediately follows. The variable Sample Rate mode is enabled by performing the following steps:  Setting the VRA bit in the AC97 Controller Mode Register (AC97C_MR).  Enable Variable Rate mode in the AC97 Codec by performing a transfer on the Codec channel. Slot 1 of the input frame is automatically interpreted as SLOTREQ signaling bits. The AC97 Controller will automatically fill the active slots according to both SLOTREQ and AC97C_OCA register in the next transmitted frame. 42.7.5 Power Management 42.7.5.1 Powering Down the AC-Link The AC97 Codecs can be placed in low power mode. The application can bring AC97 Codec to a power down state by performing sequential writes to AC97 Codec powerdown register. Both the bit clock (clock delivered by AC97 Codec, AC97CK) and the input line (AC97RX) are held at a logic low voltage level. This puts AC97 Codec in power down state while all its registers are still holding current values. Without the bit clock, the AC-link is completely in a power down state. The AC97 Controller should not attempt to play or capture audio data until it has awakened AC97 Codec. To set the AC97 Codec in low power mode, the PR4 bit in the AC97 Codec powerdown register (Codec address 0x26) must be set to 1. Then the primary Codec drives both AC97CK and AC97RX to a low logic voltage level. The following operations must be done to put AC97 Codec in low power mode:  Disable Channel A clearing CEN field in the AC97C_CAMR.  Disable Channel B clearing CEN field in the AC97C_CBMR.  Write 0x2680 value in the AC97C_COTHR.  Poll the TXEMPTY flag in AC97C_CxSRs for the 2 channels. At this point AC97 Codec is in low power mode. 42.7.5.2 Waking up the AC-link There are two methods to bring the AC-link out of low power mode. Regardless of the method, it is always the AC97 Controller that performs the wake-up. 42.7.5.3 Wake-up Triggered by the AC97 Controller The AC97 Controller can wake up the AC97 Codec by issuing either a cold or a warm reset. The AC97 Controller can also wake up the AC97 Codec by asserting AC97FS signal, however this action should not be performed for a minimum period of four audio frames following the frame in which the powerdown was issued. 42.7.5.4 Wake-up Triggered by the AC97 Codec This feature is implemented in AC97 modem codecs that need to report events such as Caller-ID and wake-up on ring. 1060 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The AC97 Codec can drive AC97RX signal from low to high level and holding it high until the controller issues either a cold or a worm reset. The AC97RX rising edge is asynchronously (regarding AC97FS) detected by the AC97 Controller. If WKUP bit is enabled in AC97C_IMR, an interrupt is triggered that wakes up the AC97 Controller which should then immediately issue a cold or a warm reset. If the processor needs to be awakened by an external event, the AC97RX signal must be externally connected to the WAKEUP entry of the system controller. Figure 42-7. AC97 Power-Down/Up Sequence Wake Event Power Down Frame Sleep State Warm Reset New Audio Frame AC97CK AC97FS AC97TX TAG Write to Data TAG Slot1 Slot2 0x26 PR4 Write to Data AC97RX TAG TAG Slot1 Slot2 0x26 PR4 42.7.5.5 AC97 Codec Reset There are three ways to reset an AC97 Codec. 42.7.5.6 Cold AC97 Reset A cold reset is generated by asserting the RESET signal low for the minimum specified time (depending on the AC97 Codec) and then by de-asserting RESET high. AC97CK and AC97FS is reactivated and all AC97 Codec registers are set to their default power-on values. Transfers on AC-link can resume. The RESET signal will be controlled via a PIO line. This is how an application should perform a cold reset:  Clear and set ENA flag in the AC97C_MR to reset the AC97 Controller  Clear PIO line output controlling the AC97 RESET signal  Wait for the minimum specified time  Set PIO line output controlling the AC97 RESET signal AC97CK, the clock provided by AC97 Codec, is detected by the controller. 42.7.5.7 Warm AC97 Reset A warm reset reactivates the AC-link without altering AC97 Codec registers. A warm reset is signaled by driving AC97FX signal high for a minimum of 1us in the absence of AC97CK. In the absence of AC97CK, AC97FX is treated as an asynchronous (regarding AC97FX) input used to signal a warm reset to AC97 Codec. This is the right way to perform a warm reset:  Set WRST in the AC97C_MR.  Wait for at least 1us  Clear WRST in the AC97C_MR. The application can check that operations have resumed by checking SOF flag in the AC97C_SR or wait for an interrupt notice if SOF is enabled in AC97C_IMR. SAM9M11 [DATASHEET] 1061 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8 AC97 Controller (AC97C) User Interface Table 42-6. Register Mapping Offset Register Name Access Reset 0x0–0x4 Reserved – – – 0x8 Mode Register AC97C_MR Read/Write 0x0 0xC Reserved – – – 0x10 Input Channel Assignment Register AC97C_ICA Read/Write 0x0 0x14 Output Channel Assignment Register AC97C_OCA Read/Write 0x0 0x18–0x1C Reserved – – – 0x20 Channel A Receive Holding Register AC97C_CARHR Read-only 0x0 0x24 Channel A Transmit Holding Register AC97C_CATHR Write-only – 0x28 Channel A Status Register AC97C_CASR Read-only 0x0 0x2C Channel A Mode Register AC97C_CAMR Read/Write 0x0 0x30 Channel B Receive Holding Register AC97C_CBRHR Read-only 0x0 0x34 Channel B Transmit Holding Register AC97C_CBTHR Write-only – 0x38 Channel B Status Register AC97C_CBSR Read-only 0x0 0x3C Channel B Mode Register AC97C_CBMR Read/Write 0x0 0x40 Codec Channel Receive Holding Register AC97C_CORHR Read-only 0x0 0x44 Codec Channel Transmit Holding Register AC97C_COTHR Write-only – 0x48 Codec Status Register AC97C_COSR Read-only 0x0 0x4C Codec Mode Register AC97C_COMR Read/Write 0x0 0x50 Status Register AC97C_SR Read-only 0x0 0x54 Interrupt Enable Register AC97C_IER Write-only – 0x58 Interrupt Disable Register AC97C_IDR Write-only – 0x5C Interrupt Mask Register AC97C_IMR Read-only 0x0 0x60–0xFB Reserved – – – Reserved for Peripheral DMA Controller (PDC) 0x100–0x124 – – – registers related to channel transfers 1062 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.1 AC97 Controller Mode Register Name: AC97C_MR Address: 0xFFFAC008 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – VRA WRST ENA • VRA: Variable Rate (for Data Slots 3-12) 0: Variable Rate is inactive. (48 kHz only) 1: Variable Rate is active. • WRST: Warm Reset 0: Warm Reset is inactive. 1: Warm Reset is active. • ENA: AC97 Controller Global Enable 0: No effect. AC97 function as well as access to other AC97 Controller registers are disabled. 1: Activates the AC97 function. SAM9M11 [DATASHEET] 1063 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.2 AC97 Controller Input Channel Assignment Register Name: AC97C_ICA Address: 0xFFFAC010 Access: Read/Write 31 30 29 28 27 26 25 24 – – CHID12 CHID11 23 22 21 20 19 18 17 16 CHID10 CHID9 CHID8 15 14 13 12 11 10 9 8 CHID8 CHID7 CHID6 CHID5 7 6 5 4 3 2 1 0 CHID5 CHID4 CHID3 • CHIDx: Channel ID for the input slot x CHIDx Selected Receive Channel 0x0 None. No data will be received during this slot time 0x1 Channel A data will be received during this slot time. 0x2 Channel B data will be received during this slot time 1064 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.3 AC97 Controller Output Channel Assignment Register Name: AC97C_OCA Address: 0xFFFAC014 Access: Read/Write 31 30 29 28 27 26 25 24 – – CHID12 CHID11 23 22 21 20 19 18 17 16 CHID10 CHID9 CHID8 15 14 13 12 11 10 9 8 CHID8 CHID7 CHID6 CHID5 7 6 5 4 3 2 1 0 CHID5 CHID4 CHID3 • CHIDx: Channel ID for the output slot x CHIDx Selected Transmit Channel 0x0 None. No data will be transmitted during this slot time 0x1 Channel A data will be transferred during this slot time. 0x2 Channel B data will be transferred during this slot time SAM9M11 [DATASHEET] 1065 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.4 AC97 Controller Codec Channel Receive Holding Register Name: AC97C_CORHR Address: 0xFFFAC040 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 SDATA 7 6 5 4 3 2 1 0 SDATA • SDATA: Status Data Data sent by the CODEC in the third AC97 input frame slot (Slot 2). 1066 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.5 AC97 Controller Codec Channel Transmit Holding Register Name: AC97C_COTHR Address: 0xFFFAC044 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 READ CADDR 15 14 13 12 11 10 9 8 CDATA 7 6 5 4 3 2 1 0 CDATA • READ: Read-write Command 0: Write operation to the CODEC register indexed by the CADDR address. 1: Read operation to the CODEC register indexed by the CADDR address. This flag is sent during the second AC97 frame slot • CADDR: CODEC Control Register Index Data sent to the CODEC in the second AC97 frame slot. • CDATA: Command Data Data sent to the CODEC in the third AC97 frame slot (Slot 2). SAM9M11 [DATASHEET] 1067 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.6 AC97 Controller Channel A, Channel B, Receive Holding Register Name: AC97C_CARHR, AC97C_CBRHR Address: 0xFFFAC020 Address: 0xFFFAC030 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – RDATA 15 14 13 12 11 10 9 8 RDATA 7 6 5 4 3 2 1 0 RDATA • RDATA: Receive Data Received Data on channel x. 1068 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.7 AC97 Controller Channel A, Channel B, Transmit Holding Register Name: AC97C_CATHR, AC97C_CBTHR Address: 0xFFFAC024 Address: 0xFFFAC034 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – TDATA 15 14 13 12 11 10 9 8 TDATA 7 6 5 4 3 2 1 0 TDATA • TDATA: Transmit Data Data to be sent on channel x. SAM9M11 [DATASHEET] 1069 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.8 AC97 Controller Channel A Status Register Name: AC97C_CASR Address: 0xFFFAC028 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 RXBUFF ENDRX – – TXBUFE ENDTX – – 7 6 5 4 3 2 1 0 – – OVRUN RXRDY – UNRUN TXEMPTY TXRDY • TXRDY: Channel Transmit Ready 0: Data has been loaded in Channel Transmit Register and is waiting to be loaded in the Channel Transmit Shift Register. 1: Channel Transmit Register is empty. • TXEMPTY: Channel Transmit Empty 0: Data remains in the Channel Transmit Register or is currently transmitted from the Channel Transmit Shift Register. 1: Data in the Channel Transmit Register have been loaded in the Channel Transmit Shift Register and sent to the codec. • UNRUN: Transmit Underrun Active only when Variable Rate Mode is enabled (VRA bit set in the AC97C_MR). Automatically cleared by a processor read operation. 0: No data has been requested from the channel since the last read of the Status Register, or data has been available each time the CODEC requested new data from the channel since the last read of the Status Register. 1: Data has been emitted while no valid data to send has been previously loaded into the Channel Transmit Shift Register since the last read of the Status Register. • RXRDY: Channel Receive Ready 0: Channel Receive Holding Register is empty. 1: Data has been received and loaded in Channel Receive Holding Register. • OVRUN: Receive Overrun Automatically cleared by a processor read operation. 0: No data has been loaded in the Channel Receive Holding Register while previous data has not been read since the last read of the Status Register. 1: Data has been loaded in the Channel Receive Holding Register while previous data has not yet been read since the last read of the Status Register. • ENDTX: End of Transmission for Channel A 0: The register AC97C_CATCR has not reached 0 since the last write in AC97C_CATCR or AC97C_CANCR. 1: The register AC97C_CATCR has reached 0 since the last write in AC97C_CATCR or AC97C_CATNCR. 1070 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• TXBUFE: Transmit Buffer Empty for Channel A 0: AC97C_CATCR or AC97C_CATNCR have a value other than 0. 1: Both AC97C_CATCR and AC97C_CATNCR have a value of 0. • ENDRX: End of Reception for Channel A 0: The register AC97C_CARCR has not reached 0 since the last write in AC97C_CARCR or AC97C_CARNCR. 1: The register AC97C_CARCR has reached 0 since the last write in AC97C_CARCR or AC97C_CARNCR. • RXBUFF: Receive Buffer Full for Channel A 0: AC97C_CARCR or AC97C_CARNCR have a value other than 0. 1: Both AC97C_CARCR and AC97C_CARNCR have a value of 0. SAM9M11 [DATASHEET] 1071 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.9 AC97 Controller Channel B Status Register Name: AC97C_CBSR Address: 0xFFFAC038 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 RXBUFF ENDRX – – – TXBUFE ENDTX – 7 6 5 4 3 2 1 0 – – OVRUN RXRDY – UNRUN TXEMPTY TXRDY • TXRDY: Channel Transmit Ready 0: Data has been loaded in Channel Transmit Register and is waiting to be loaded in the Channel Transmit Shift Register. 1: Channel Transmit Register is empty. • TXEMPTY: Channel Transmit Empty 0: Data remains in the Channel Transmit Register or is currently transmitted from the Channel Transmit Shift Register. 1: Data in the Channel Transmit Register have been loaded in the Channel Transmit Shift Register and sent to the codec. • UNRUN: Transmit Underrun Active only when Variable Rate Mode is enabled (VRA bit set in the AC97C_MR). Automatically cleared by a processor read operation. 0: No data has been requested from the channel since the last read of the Status Register, or data has been available each time the CODEC requested new data from the channel since the last read of the Status Register. 1: Data has been emitted while no valid data to send has been previously loaded into the Channel Transmit Shift Register since the last read of the Status Register. • RXRDY: Channel Receive Ready 0: Channel Receive Holding Register is empty. 1: Data has been received and loaded in Channel Receive Holding Register. • OVRUN: Receive Overrun Automatically cleared by a processor read operation. 0: No data has been loaded in the Channel Receive Holding Register while previous data has not been read since the last read of the Status Register. 1: Data has been loaded in the Channel Receive Holding Register while previous data has not yet been read since the last read of the Status Register. • ENDTX: End of Transmission for Channel B 0: The register AC97C_CBTCR has not reached 0 since the last write in AC97C_CBTCR or AC97C_CBNCR. 1: The register AC97C_CBTCR has reached 0 since the last write in AC97C_CBTCR or AC97C_CBTNCR. 1072 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• TXBUFE: Transmit Buffer Empty for Channel B 0: AC97C_CBTCR or AC97C_CBTNCR have a value other than 0. 1: Both AC97C_CBTCR and AC97C_CBTNCR have a value of 0. • ENDRX: End of Reception for Channel B 0: The register AC97C_CBRCR has not reached 0 since the last write in AC97C_CBRCR or AC97C_CBRNCR. 1: The register AC97C_CBRCR has reached 0 since the last write in AC97C_CBRCR or AC97C_CBRNCR. • RXBUFF: Receive Buffer Full for Channel B 0: AC97C_CBRCR or AC97C_CBRNCR have a value other than 0. 1: Both AC97C_CBRCR and AC97C_CBRNCR have a value of 0. SAM9M11 [DATASHEET] 1073 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.10AC97 Controller Codec Status Register Name: AC97C_COSR Address: 0xFFFAC048 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – OVRUN RXRDY – UNRUN TXEMPTY TXRDY • TXRDY: Channel Transmit Ready 0: Data has been loaded in Channel Transmit Register and is waiting to be loaded in the Channel Transmit Shift Register. 1: Channel Transmit Register is empty. • TXEMPTY: Channel Transmit Empty 0: Data remains in the Channel Transmit Register or is currently transmitted from the Channel Transmit Shift Register. 1: Data in the Channel Transmit Register have been loaded in the Channel Transmit Shift Register and sent to the codec. • UNRUN: Transmit Underrun Active only when Variable Rate Mode is enabled (VRA bit set in the AC97C_MR). Automatically cleared by a processor read operation. 0: No data has been requested from the channel since the last read of the Status Register, or data has been available each time the CODEC requested new data from the channel since the last read of the Status Register. 1: Data has been emitted while no valid data to send has been previously loaded into the Channel Transmit Shift Register since the last read of the Status Register. • RXRDY: Channel Receive Ready 0: Channel Receive Holding Register is empty. 1: Data has been received and loaded in Channel Receive Holding Register. • OVRUN: Receive Overrun Automatically cleared by a processor read operation. 0: No data has been loaded in the Channel Receive Holding Register while previous data has not been read since the last read of the Status Register. 1: Data has been loaded in the Channel Receive Holding Register while previous data has not yet been read since the last read of the Status Register. 1074 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.11 AC97 Controller Channel A Mode Register Name: AC97C_CAMR Address: 0xFFFAC02C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – PDCEN CEN – – CEM SIZE 15 14 13 12 11 10 9 8 RXBUFF ENDRX – – TXBUFE ENDTX – – 7 6 5 4 3 2 1 0 – – OVRUN RXRDY – UNRUN TXEMPTY TXRDY • TXRDY: Channel Transmit Ready Interrupt Enable • TXEMPTY: Channel Transmit Empty Interrupt Enable • UNRUN: Transmit Underrun Interrupt Enable • RXRDY: Channel Receive Ready Interrupt Enable • OVRUN: Receive Overrun Interrupt Enable • ENDTX: End of Transmission for Channel A Interrupt Enable • TXBUFE: Transmit Buffer Empty for Channel A Interrupt Enable 0: Read: the corresponding interrupt is disabled. Write: disables the corresponding interrupt. 1: Read: the corresponding interrupt is enabled. Write: enables the corresponding interrupt. • ENDRX: End of Reception for Channel A Interrupt Enable 0: Read: the corresponding interrupt is disabled. Write: disables the corresponding interrupt. 1: Read: the corresponding interrupt is enabled. Write: enables the corresponding interrupt. • RXBUFF: Receive Buffer Full for Channel A Interrupt Enable 0: Read: the corresponding interrupt is disabled. Write: disables the corresponding interrupt. 1: Read: the corresponding interrupt is enabled. Write: enables the corresponding interrupt. • SIZE: Channel A Data Size SIZE Encoding SIZE Selected Data Size 0x0 20 bits 0x1 18 bits 0x2 16 bits 0x3 10 bits Note: Each time slot in the data phase is 20 bit long. For example, if a 16-bit sample stream is being played to an AC 97 DAC, the first 16 bit positions are presented to the DAC MSB-justified. They are followed by the next four bit positions that the AC97 Controller fills with zeroes. This process ensures that the least significant bits do not introduce any DC biasing, regardless of the implemented DAC’s resolution (16-, 18-, or 20-bit) SAM9M11 [DATASHEET] 1075 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• CEM: Channel A Endian Mode 0: Transferring Data through Channel A is straight forward (Little-Endian). 1: Transferring Data through Channel A from/to a memory is performed with from/to Big-Endian format translation. • CEN: Channel A Enable 0: Data transfer is disabled on Channel A. 1: Data transfer is enabled on Channel A. • PDCEN: Peripheral Data Controller Channel Enable 0: Channel A is not transferred through a Peripheral Data Controller Channel. Related PDC flags are ignored or not generated. 1: Channel A is transferred through a Peripheral Data Controller Channel. Related PDC flags are taken into account or generated. 1076 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.12AC97 Controller Channel B Mode Register Name: AC97C_CBMR Address: 0xFFFAC03C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – PDCEN CEN – – CEM SIZE 15 14 13 12 11 10 9 8 RXBUFF ENDRX – – TXBUFE ENDTX – – 7 6 5 4 3 2 1 0 – – OVRUN RXRDY – UNRUN TXEMPTY TXRDY • TXRDY: Channel Transmit Ready Interrupt Enable • TXEMPTY: Channel Transmit Empty Interrupt Enable • UNRUN: Transmit Underrun Interrupt Enable • RXRDY: Channel Receive Ready Interrupt Enable • OVRUN: Receive Overrun Interrupt Enable • ENDTX: End of Transmission for Channel B Interrupt Enable • TXBUFE: Transmit Buffer Empty for Channel B Interrupt Enable 0: Read: the corresponding interrupt is disabled. Write: disables the corresponding interrupt. 1: Read: the corresponding interrupt is enabled. Write: enables the corresponding interrupt. • ENDRX: End of Reception for Channel B Interrupt Enable 0: Read: the corresponding interrupt is disabled. Write: disables the corresponding interrupt. 1: Read: the corresponding interrupt is enabled. Write: enables the corresponding interrupt. • RXBUFF: Receive Buffer Full for Channel B Interrupt Enable 0: Read: the corresponding interrupt is disabled. Write: disables the corresponding interrupt. 1: Read: the corresponding interrupt is enabled. Write: enables the corresponding interrupt. • SIZE: Channel B Data Size SIZE Encoding SIZE Selected Data Size 0x0 20 bits 0x1 18 bits 0x2 16 bits 0x3 10 bits Note: Each time slot in the data phase is 20 bit long. For example, if a 16-bit sample stream is being played to an AC 97 DAC, the first 16 bit positions are presented to the DAC MSB-justified. They are followed by the next four bit positions that the AC97 Controller fills with zeroes. This process ensures that the least significant bits do not introduce any DC biasing, regardless of the implemented DAC’s resolution (16-, 18-, or 20-bit). SAM9M11 [DATASHEET] 1077 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• CEM: Channel B Endian Mode 0: Transferring Data through Channel B is straight forward (Little-Endian). 1: Transferring Data through Channel B from/to a memory is performed with from/to Big-Endian format translation. • CEN: Channel B Enable 0: Data transfer is disabled on Channel B. 1: Data transfer is enabled on Channel B. • PDCEN: Peripheral Data Controller Channel Enable 0: Channel B is not transferred through a Peripheral Data Controller Channel. Related PDC flags are ignored or not generated. 1: Channel B is transferred through a Peripheral Data Controller Channel. Related PDC flags are taken into account or generated. 1078 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.13AC97 Controller Codec Mode Register Name: AC97C_COMR Address: 0xFFFAC04C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – OVRUN RXRDY – UNRUN TXEMPTY TXRDY • TXRDY: Channel Transmit Ready Interrupt Enable • TXEMPTY: Channel Transmit Empty Interrupt Enable • UNRUN: Transmit Underrun Interrupt Enable • RXRDY: Channel Receive Ready Interrupt Enable • OVRUN: Receive Overrun Interrupt Enable SAM9M11 [DATASHEET] 1079 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.14AC97 Controller Status Register Name: AC97C_SR Address: 0xFFFAC050 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – CBEVT CAEVT COEVT WKUP SOF WKUP and SOF flags in AC97C_SR are automatically cleared by a processor read operation. • SOF: Start Of Frame 0: No Start of Frame has been detected since the last read of the Status Register. 1: At least one Start of frame has been detected since the last read of the Status Register. • WKUP: Wake Up detection 0: No Wake-up has been detected. 1: At least one rising edge on SDATA_IN has been asynchronously detected. That means AC97 Codec has notified a wake-up. • COEVT: CODEC Channel Event A Codec channel event occurs when AC97C_COSR AND AC97C_COMR is not 0. COEVT flag is automatically cleared when the channel event condition is cleared. 0: No event on the CODEC channel has been detected since the last read of the Status Register. 1: At least one event on the CODEC channel is active. • CAEVT: Channel A Event A channel A event occurs when AC97C_CASR AND AC97C_CAMR is not 0. CAEVT flag is automatically cleared when the channel event condition is cleared. 0: No event on the channel A has been detected since the last read of the Status Register. 1: At least one event on the channel A is active. • CBEVT: Channel B Event A channel B event occurs when AC97C_CBSR AND AC97C_CBMR is not 0. CBEVT flag is automatically cleared when the channel event condition is cleared. 0: No event on the channel B has been detected since the last read of the Status Register. 1: At least one event on the channel B is active. 1080 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.15AC97 Codec Controller Interrupt Enable Register Name: AC97C_IER Address: 0xFFFAC054 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – CBEVT CAEVT COEVT WKUP SOF • SOF: Start Of Frame • WKUP: Wake Up • COEVT: Codec Event • CAEVT: Channel A Event • CBEVT: Channel B Event 0: No effect. 1: Enables the corresponding interrupt. SAM9M11 [DATASHEET] 1081 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.16AC97 Controller Interrupt Disable Register Name: AC97C_IDR Address: 0xFFFAC058 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – CBEVT CAEVT COEVT WKUP SOF • SOF: Start Of Frame • WKUP: Wake Up • COEVT: Codec Event • CAEVT: Channel A Event • CBEVT: Channel B Event 0: No effect. 1: Disables the corresponding interrupt. 1082 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

42.8.17AC97 Controller Interrupt Mask Register Name: AC97C_IMR Address: 0xFFFAC05C Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – CBEVT CAEVT COEVT WKUP SOF • SOF: Start Of Frame • WKUP: Wake Up • COEVT: Codec Event • CAEVT: Channel A Event • CBEVT: Channel B Event 0: The corresponding interrupt is disabled. 1: The corresponding interrupt is enabled. SAM9M11 [DATASHEET] 1083 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

43. Advanced Encryption Standard (AES) 43.1 Description The Advanced Encryption Standard (AES) is compliant with the American FIPS (Federal Information Processing Standard) Publication 197 specification. The AES supports all five confidentiality modes of operation for symmetrical key block cipher algorithms (ECB, CBC, OFB, CFB and CTR), as specified in the NIST Special Publication 800-38A Recommendation. It is compatible with all these modes via Peripheral DMA Controller channels, minimizing processor intervention for large buffer transfers. The 128-bit/192-bit/256-bit key is stored in four/six/eight 32-bit registers (AES_KEYWRx) which are all write-only. The 128-bit input data and initialization vector (for some modes) are each stored in four 32-bit registers (AES_IDATARx and AES_IVRx) which are all write-only. As soon as the initialization vector, the input data and the key are configured, the encryption/decryption process may be started. Then the encrypted/decrypted data is ready to be read out on the four 32-bit output data registers (AES_ODATARx) or through the DMA channels. 43.2 Embedded Characteristics  Compliant with FIPS Publication 197, Advanced Encryption Standard (AES)  256-bit Cryptographic Key  16 Clock Cycles Encryption/Decryption Processing Time with a 256-bit Cryptographic Key  Support of the Five Standard Modes of Operation Specified in the NIST Special Publication 800- 38A, Recommendation for Block Cipher Modes of Operation - Methods and Techniques: ̶ Electronic Code Book (ECB) ̶ Cipher Block Chaining (CBC) ̶ Cipher Feedback (CFB) ̶ Output Feedback (OFB) ̶ Counter (CTR)  8-, 16-, 32-, 64- and 128-bit Data Sizes Possible in CFB Mode  Last Output Data Mode Allows Optimized Message Authentication Code (MAC) Generation  Hardware Countermeasures  Connected to the DMA Controller to Optimize Data Transfers for all Operating Modes ̶ One Channel for the Receiver, One Channel for the Transmitter ̶ Next Buffer Support 1084 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

43.3 Product Dependencies 43.3.1 Power Management The AES may be clocked through the Power Management Controller (PMC), so the programmer must first to configure the PMC to enable the AES clock. 43.3.2 Interrupt The AES interface has an interrupt line connected to the Interrupt Controller. Handling the AES interrupt requires programming the Interrupt Controller before configuring the AES. Table 43-1. Peripheral IDs Instance ID AES 28 43.4 Functional Description The Advanced Encryption Standard (AES) specifies a FIPS-approved cryptographic algorithm that can be used to protect electronic data. The AES algorithm is a symmetric block cipher that can encrypt (encipher) and decrypt (decipher) information. Encryption converts data to an unintelligible form called ciphertext. Decrypting the ciphertext converts the data back into its original form, called plaintext. The CIPHER bit in the AES Mode Register (AES_MR) allows selection between the encryption and the decryption processes. The AES is capable of using cryptographic keys of 128/192/256 bits to encrypt and decrypt data in blocks of 128 bits. This 128-bit/192-bit/256-bit key is defined in the Key Registers (AES_KEYWRx). The input to the encryption processes of the CBC, CFB, and OFB modes includes, in addition to the plaintext, a 128-bit data block called the initialization vector (IV), which must be set in the Initialization Vector Registers (AES_IVRx). The initialization vector is used in an initial step in the encryption of a message and in the corresponding decryption of the message. The Initialization Vector Registers are also used by the CTR mode to set the counter value. 43.4.1 Operation Modes The AES supports the following modes of operation:  ECB: Electronic Code Book  CBC: Cipher Block Chaining  OFB: Output Feedback  CFB: Cipher Feedback ̶ CFB8 (CFB where the length of the data segment is 8 bits) ̶ CFB16 (CFB where the length of the data segment is 16 bits) ̶ CFB32 (CFB where the length of the data segment is 32 bits) ̶ CFB64 (CFB where the length of the data segment is 64 bits) ̶ CFB128 (CFB where the length of the data segment is 128 bits)  CTR: Counter The data pre-processing, post-processing and data chaining for the concerned modes are automatically performed. Refer to the NIST Special Publication 800-38A Recommendation for more complete information. These modes are selected by setting the OPMOD field in the AES Mode Register (AES_MR). SAM9M11 [DATASHEET] 1085 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

In CFB mode, five data sizes are possible (8, 16, 32, 64 or 128 bits), configurable by means of the CFBS field in the mode register. (See “AES Mode Register” on page 1093.). In CTR mode, the size of the block counter embedded in the module is 16 bits. Therefore, there is a rollover after processing 1 megabyte of data. 43.4.2 Start Modes The SMOD field in the AES Mode Register (AES_MR) allows selection of the encryption (or decryption) start mode. 43.4.2.1 Manual Mode The sequence order is as follows:  Write the Mode Register (AES_MR) with all required fields, including but not limited to SMOD and OPMOD.  Write the 128-bit/192-bit/256-bit key in the Key Registers (AES_KEYWRx).  Write the initialization vector (or counter) in the Initialization Vector Registers (AES_IVRx). Note: The Initialization Vector Registers concern all modes except ECB.  Set the bit DATRDY (Data Ready) in the AES Interrupt Enable register (AES_IER), depending on whether an interrupt is required or not at the end of processing.  Write the data to be encrypted/decrypted in the authorized Input Data Registers (See Table 43-2). Table 43-2. Authorized Input Data Registers Operation Mode Input Data Registers to Write ECB All CBC All OFB All 128-bit CFB All 64-bit CFB AES_IDATAR0 and AES_IDATAR1 32-bit CFB AES_IDATAR0 16-bit CFB AES_IDATAR0 8-bit CFB AES_IDATAR0 CTR All Note: In 64-bit CFB mode, writing to AES_IDATAR2 and AES_IDATAR3 registers is not allowed and may lead to errors in processing. Note: In 32-, 16- and 8-bit CFB modes, writing to AES_IDATAR1, AES_IDATAR2 and AES_IDATAR3 registers is not allowed and may lead to errors in processing.  Set the START bit in the AES Control register AES_CR to begin the encryption or the decryption process.  When processing completes, the bit DATRDY in the AES Interrupt Status Register (AES_ISR) raises. If an interrupt has been enabled by setting the bit DATRDY in AES_IER, the interrupt line of the AES is activated.  When the software reads one of the Output Data Registers (AES_ODATARx), the DATRDY bit is automatically cleared. 43.4.2.2 Auto Mode The Auto Mode is similar to the manual one, except that in this mode, as soon as the correct number of Input Data registers is written, processing is automatically started without any action in the Control Register. 1086 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

43.4.2.3 DMA Mode The DMA Controller can be used in association with the AES to perform an encryption/decryption of a buffer without any action by the software during processing. The SMOD field of the AES_MR must be set either to 0x1 or 0x2 depending on how the DMA is configured. The start address of any transfer descriptor must be set to AES_IDATAR0 register. The DMA chunk size can be set either to single data or to 4 data per request.  If the entire AES message to be processed requires only a single DMA transfer descriptor, or if the message is transferred using several DMA transfer descriptors which sizes are greater than 128bits (4 words), the DMA must be configured with non incremental addresses. Then, the SMOD field of the AES_MR must be set to 0x2.  If the AES message is described using DMA transfer descriptors having a transfer size equal to 128bits (4 words), the DMA must be configured to perform non incremental addresses. Then, the SMOD field of the AES_MR must be set to 0x1. When DMA is used, the type of data transfer (byte, half-word or word) depends on the operation mode. Table 43-3. Data Transfer Type for the Different Operation Modes Operation Mode Data Transfer Type ECB Word CBC Word OFB Word CFB 128-bit Word CFB 64-bit Word CFB 32-bit Word CFB 16-bit Half-word CFB 8-bit Byte CTR Word 43.4.3 Last Output Data Mode This mode is used to generate cryptographic checksums on data (MAC) by means of cipher block chaining encryption algorithm (CBC-MAC algorithm for example). After each end of encryption/decryption, the output data is available either on the output data registers for Manual and Auto mode or at the address specified in the receive buffer pointer for DMA mode (See Table 43-4). The Last Output Data bit (LOD) in the AES Mode Register (AES_MR) allows retrieval of only the last data of several encryption/decryption processes. Therefore, there is no need to define a read buffer in DMA mode. This data is only available on the Output Data Registers (AES_ODATARx). SAM9M11 [DATASHEET] 1087 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

43.4.3.1 Manual and Auto Modes If LOD = 0 The DATRDY flag is cleared when at least one of the Output Data Registers is read (See Figure 43-1). Figure 43-1. Manual and Auto Modes with LOD = 0 Write START bit in AES_CR (Manual mode) or Write AES_IDATARx register(s) (Auto mode) Read the AES_ODATARx DATRDY Encryption or Decryption Process If the user does not want to read the output data registers between each encryption/decryption, the DATRDY flag will not be cleared. If the DATRDY flag is not cleared, the user cannot know the end of the following encryptions/decryptions. If LOD = 1 The DATRDY flag is cleared when at least one Input Data Register is written, so before the start of a new transfer (See Figure 43-2). No more Output Data Register reads are necessary between consecutive encryptions/decryptions. Figure 43-2. Manual and Auto Modes with LOD = 1 Write START bit in AES_CR (Manual mode) or Write AES_IDATARx register(s) (Auto mode) Write AES_IDATARx register(s) DATRDY Encryption or Decryption Process 1088 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

43.4.3.2 DMA Mode If LOD = 0 This mode may be used for all AES operating modes except CBC-MAC where LOD=1 mode is recommended. The end of the encryption/decryption is notified by the end of DMA transfer associated to AES_ODATARx registers (see Figure 43-3). 2 channels DMA are required, 1 for writing message blocks to AES_IDATARx registers and the other one to get back the processed from AES_ODATARx registers. Figure 43-3. DMA transfer with LOD = 0 Enable DMA Channels associated to AES_IDATARx and AES_ODATARx Multiple Encryption or Decryption Processes Write accesses into AES_IDATARx BTC /channel 0 Read accesses into AES_ODATARx Message fully processed BTC /channel 1 (cipher or decipher) last block can be read If LOD = 1 This mode is recommended to process AES CBC-MAC operating mode. The user must first wait for the DMA flag (BTC = Buffer Transfer Complete) to rise, then for DATRDY to ensure that the encryption/decryption is completed (see Figure 43-4). In this case, no receive buffers are required. The output data is only available on the Output Data Registers (AES_ODATARx). Figure 43-4. DMA transfer with LOD = 1 Enable DMA Channels associated with AES_IDATARx and AES_ODATARx registers Multiple Encryption or Decryption Processes Write accesses into AES_IDATARx BTC / channel 0 DATRDY Message fully processed (cipher or decipher) Message fully transferred MAC result can be read SAM9M11 [DATASHEET] 1089 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 43-3 summarizes the different cases. Table 43-4. Last Output Data Mode Behavior versus Start Modes Manual and Auto Modes DMA Transfer Sequence LOD = 0 LOD = 1 LOD = 0 LOD = 1 At least one Output DATRDY Flag Clearing At least one Input Data Data Register must be Not used Managed by the DMA Condition (1) Register must be written read Encrypted/Decrypted In the Output Data In the Output Data In the Output Data Not available Data Result Location Registers Registers Registers End of 2 DMA flags DMA flag (BTC[n]) DATRDY DATRDY Encryption/Decryption (BTC[n/m]) then AES DATRDY Note: 1. Depending on the mode, there are other ways of clearing the DATRDY flag. See “AES Interrupt Status Register” on page 1099. Warning: In DMA mode, reading to the Output Data registers before the last data transfer may lead to unpredictable result. 43.4.4 Security Features 43.4.4.1 Countermeasures The AES also features hardware countermeasures that can be used to make more difficult the unexpected data recovery. These countermeasures can be enabled through the CTYPE field in the AES Mode Register. This field is write- only, and all changes to it are taken into account if, at the same time, the Countermeasure Key (CKEY field) is correctly written (see “AES Mode Register” on page 1093). Note: Enabling countermeasures has an impact on the AES encryption/decryption throughput. By default, all the countermeasures are enabled. The best throughput is achieved with all the countermeasures disabled. On the other hand, the best protection is achieved with all of them enabled. The LOADSEED bit in the AES Control Register (AES_CR) restarts the countermeasures generator to an internal pre-defined value. 43.4.4.2 Unspecified Register Access Detection When an unspecified register access occurs, the URAD bit in the Interrupt Status Register (AES_ISR) raises. Its source is then reported in the Unspecified Register Access Type field (URAT). Only the last unspecified register access is available through the URAT field. Several kinds of unspecified register accesses can occur:  Input Data Register written during the data processing when SMOD=IDATAR0_START  Output Data Register read during data processing  Mode Register written during data processing  Output Data Register read during sub-keys generation  Mode Register written during sub-keys generation  Write-only register read access The URAD bit and the URAT field can only be reset by the SWRST bit in the AES_CR. 1090 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

43.5 Advanced Encryption Standard (AES) User Interface Table 43-5. Register Mapping Offset Register Name Access Reset 0x00 Control Register AES_CR Write-only – 0x04 Mode Register AES_MR Read/Write 0x0 0x08–0x0C Reserved – – – 0x10 Interrupt Enable Register AES_IER Write-only – 0x14 Interrupt Disable Register AES_IDR Write-only – 0x18 Interrupt Mask Register AES_IMR Read-only 0x0 0x1C Interrupt Status Register AES_ISR Read-only 0x0 0x20 Key Word Register 0 AES_KEYWR0 Write-only – 0x24 Key Word Register 1 AES_KEYWR1 Write-only – 0x28 Key Word Register 2 AES_KEYWR2 Write-only – 0x2C Key Word Register 3 AES_KEYWR3 Write-only – 0x30 Key Word Register 4 AES_KEYWR4 Write-only – 0x34 Key Word Register 5 AES_KEYWR5 Write-only – 0x38 Key Word Register 6 AES_KEYWR6 Write-only – 0x3C Key Word Register 7 AES_KEYWR7 Write-only – 0x40 Input Data Register 0 AES_IDATAR0 Write-only – 0x44 Input Data Register 1 AES_IDATAR1 Write-only – 0x48 Input Data Register 2 AES_IDATAR2 Write-only – 0x4C Input Data Register 3 AES_IDATAR3 Write-only – 0x50 Output Data Register 0 AES_ODATAR0 Read-only 0x0 0x54 Output Data Register 1 AES_ODATAR1 Read-only 0x0 0x58 Output Data Register 2 AES_ODATAR2 Read-only 0x0 0x5C Output Data Register 3 AES_ODATAR3 Read-only 0x0 0x60 Initialization Vector Register 0 AES_IVR0 Write-only – 0x64 Initialization Vector Register 1 AES_IVR1 Write-only – 0x68 Initialization Vector Register 2 AES_IVR2 Write-only – 0x6C Initialization Vector Register 3 AES_IVR3 Write-only – 0x70–0xFC Reserved – – – SAM9M11 [DATASHEET] 1091 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

43.5.1 AES Control Register Name: AES_CR Address: 0xFFFC0000 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – LOADSEED 15 14 13 12 11 10 9 8 – – – – – – – SWRST 7 6 5 4 3 2 1 0 – – – – – – – START • START: Start Processing 0: No effect 1: Starts manual encryption/decryption process. • SWRST: Software Reset 0: No effect. 1: Resets the AES. A software triggered hardware reset of the AES interface is performed. • LOADSEED: Random Number Generator Seed Loading 0: No effect. 1: Restarts the countermeasures generator to an internal pre-defined value. 1092 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

43.5.2 AES Mode Register Name: AES_MR Address: 0xFFFC0004 Access: Read/Write 31 30 29 28 27 26 25 24 – – – CMTYP5 CMTYP4 CMTYP3 CMTYP2 CMTYP1 23 22 21 20 19 18 17 16 CKEY – CFBS 15 14 13 12 11 10 9 8 LOD OPMOD KEYSIZE SMOD 7 6 5 4 3 2 1 0 PROCDLY – – – CIPHER • CIPHER: Processing Mode 0: Decrypts data. 1: Encrypts data. • PROCDLY: Processing Delay Processing Time = 12×(PROCDLY+1) The Processing Time represents the number of clock cycles that the AES needs in order to perform one encryption/decryp- tion with no countermeasures activated. Note: The best performance is achieved with PROCDLY equal to 0. • SMOD: Start Mode Value Name Description 0x0 MANUAL_START Manual Mode 0x1 AUTO_START Auto Mode 0x2 IDATAR0_START AES_IDATAR0 access only Auto Mode Values which are not listed in the table must be considered as “reserved”. In case DMA transfer is used, either 0x1 or 0x2 must be configured. Refer to “DMA Mode” on page 1087 for more details. • KEYSIZE: Key Size Value Name Description 0x0 AES128 AES Key Size is 128 bits 0x1 AES192 AES Key Size is 192 bits 0x2 AES256 AES Key Size is 256 bits Values which are not listed in the table must be considered as “reserved”. SAM9M11 [DATASHEET] 1093 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• OPMOD: Operation Mode Value Name Description 0x0 ECB ECB: Electronic Code Book mode 0x1 CBC CBC: Cipher Block Chaining mode 0x2 OFB OFB: Output Feedback mode 0x3 CFB CFB: Cipher Feedback mode 0x4 CTR CTR: Counter mode (16-bit internal counter) Values which are not listed in the table must be considered as “reserved”. For CBC-MAC operating mode, please set OPMOD to CBC and LOD to 1. • LOD: Last Output Data Mode 0: No effect. After each end of encryption/decryption, the output data is available either on the output data registers (Manual and Auto modes). In Manual and Auto modes, the DATRDY flag is cleared when at least one of the Output Data registers is read. 1: The DATRDY flag is cleared when at least one of the Input Data Registers is written. No more Output Data Register reads is necessary between consecutive encryptions/decryptions (see “Last Output Data Mode” on page 1087). Warning: In DMA mode, reading to the Output Data registers before the last data encryption/decryption process may lead to unpredictable results. • CFBS: Cipher Feedback Data Size Value Name Description 0x0 SIZE_128BIT 128-bit 0x1 SIZE_64BIT 64-bit 0x2 SIZE_32BIT 32-bit 0x3 SIZE_16BIT 16-bit 0x4 SIZE_8BIT 8-bit Values which are not listed in table must be considered as “reserved”. • CKEY: Countermeasure Key This field should be written with the value 0xE to allow CTYPE field changes. If the field is written with a different value, changes made through the CTYPE field will not be taken into account. Note: CKEY field is write-only. • CMTYP1: CounterMeasure Type 1 0 (NOPROT_EXTXKEY): Counter-Measure type 1 is disabled 1 (PROT_EXTKEY): Counter-Measure type 1 is enabled • CMTYP2: CounterMeasure Type 2 0 (NO_PAUSE): Counter-Measure type 2 is disabled 1 (PAUSE): Counter-Measure type 2 is enabled 1094 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• CMTYP3: CounterMeasure Type 3 0 (NO_DUMMY): Counter-Measure type 3 is disabled 1 (DUMMY): Counter-Measure type 3 is enabled • CMTYP4: CounterMeasure Type 4 0 (NO_RESTART): Counter-Measure type 4 is disabled 1 (RESTART): Counter-Measure type 4 is enabled • CMTYP5: CounterMeasure Type 5 0 (NO_ADDACCESS): Counter-Measure type 5 is disabled 1 (ADDACCESS): Counter-Measure type 5 is enabled Note: All the countermeasures are enabled by default. Note: CTYPE field is write-only and can only be modified if CKEY is correctly set. SAM9M11 [DATASHEET] 1095 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

43.5.3 AES Interrupt Enable Register Name: AES_IER Address: 0xFFFC0010 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – URAD 7 6 5 4 3 2 1 0 – – – – – – – DATRDY • DATRDY: Data Ready Interrupt Enable • URAD: Unspecified Register Access Detection Interrupt Enable 0: No effect. 1: Enables the corresponding interrupt. 1096 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

43.5.4 AES Interrupt Disable Register Name: AES_IDR Address: 0xFFFC0014 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – URAD 7 6 5 4 3 2 1 0 – – – – – – – DATRDY • DATRDY: Data Ready Interrupt Disable • URAD: Unspecified Register Access Detection Interrupt Disable 0: No effect. 1: Disables the corresponding interrupt. SAM9M11 [DATASHEET] 1097 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

43.5.5 AES Interrupt Mask Register Name: AES_IMR Address: 0xFFFC0018 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – URAD 7 6 5 4 3 2 1 0 – – – – – – – DATRDY • DATRDY: Data Ready Interrupt Mask • URAD: Unspecified Register Access Detection Interrupt Mask 0: The corresponding interrupt is not enabled. 1: The corresponding interrupt is enabled. 1098 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

43.5.6 AES Interrupt Status Register Name: AES_ISR Address: 0xFFFC001C Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 URAT – – – URAD 7 6 5 4 3 2 1 0 – – – – – – – DATRDY • DATRDY: Data Ready 0: Output data is not valid. 1: Encryption or decryption process is completed. DATRDY is cleared when a Manual encryption/decryption occurs (START bit in AES_CR) or when a software triggered hardware reset of the AES interface is performed (SWRST bit in AES_CR). LOD = 0 (AES_MR): In Manual and Auto mode, the DATRDY flag can also be cleared when at least one of the Output Data Registers is read. In DMA mode, DATRDY is set and cleared automatically. LOD = 1 (AES_MR): In Manual and Auto mode, the DATRDY flag can also be cleared when at least one of the Input Data Registers is written. In DMA mode, DATRDY is set and cleared automatically. • URAD: Unspecified Register Access Detection Status 0: No unspecified register access has been detected since the last SWRST. 1: At least one unspecified register access has been detected since the last SWRST. URAD bit is reset only by the SWRST bit in the AES_CR. • URAT: Unspecified Register Access Type Value Name Description 0x0 IDR_WR_PROCESSING Input Data Register written during the data processing when SMOD=0x2 mode. 0x1 ODR_RD_PROCESSING Output Data Register read during the data processing. 0x2 MR_WR_PROCESSING Mode Register written during the data processing. 0x3 ODR_RD_SUBKGEN Output Data Register read during the sub-keys generation. 0x4 MR_WR_SUBKGEN Mode Register written during the sub-keys generation. 0x5 WOR_RD_ACCESS Write-only register read access. Only the last Unspecified Register Access Type is available through the URAT field. URAT field is reset only by the SWRST bit in the AES_CR. SAM9M11 [DATASHEET] 1099 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

43.5.7 AES Key Word Register x Name: AES_KEYWRx Address: 0xFFFC0020 Access: Write-only 31 30 29 28 27 26 25 24 KEYW 23 22 21 20 19 18 17 16 KEYW 15 14 13 12 11 10 9 8 KEYW 7 6 5 4 3 2 1 0 KEYW • KEYW: Key Word The four/six/eight 32-bit Key Word registers set the 128-bit/192-bit/256-bit cryptographic key used for encryption/decryption. AES_KEYWR0 corresponds to the first word of the key and respectively AES_KEYWR3/AES_KEYWR5/AES_KEYWR7 to the last one. These registers are write-only to prevent the key from being read by another application. 1100 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

43.5.8 AES Input Data Register x Name: AES_IDATARx Address: 0xFFFC0040 Access: Write-only 31 30 29 28 27 26 25 24 IDATA 23 22 21 20 19 18 17 16 IDATA 15 14 13 12 11 10 9 8 IDATA 7 6 5 4 3 2 1 0 IDATA • IDATA: Input Data Word The four 32-bit Input Data registers set the 128-bit data block used for encryption/decryption. AES_IDATAR0 corresponds to the first word of the data to be encrypted/decrypted, and AES_IDATAR3 to the last one. These registers are write-only to prevent the input data from being read by another application. SAM9M11 [DATASHEET] 1101 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

43.5.9 AES Output Data Register x Name: AES_ODATARx Address: 0xFFFC0050 Access: Read-only 31 30 29 28 27 26 25 24 ODATA 23 22 21 20 19 18 17 16 ODATA 15 14 13 12 11 10 9 8 ODATA 7 6 5 4 3 2 1 0 ODATA • ODATA: Output Data The four 32-bit Output Data registers contain the 128-bit data block that has been encrypted/decrypted. AES_ODATAR0 corresponds to the first word, AES_ODATAR3 to the last one. 1102 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

43.5.10AES Initialization Vector Register x Name: AES_IVRx Address: 0xFFFC0060 Access: Write-only 31 30 29 28 27 26 25 24 IV 23 22 21 20 19 18 17 16 IV 15 14 13 12 11 10 9 8 IV 7 6 5 4 3 2 1 0 IV • IV: Initialization Vector The four 32-bit Initialization Vector registers set the 128-bit Initialization Vector data block that is used by some modes of operation as an additional initial input. AES_IVR0 corresponds to the first word of the Initialization Vector, AES_IVR3 to the last one. These registers are write-only to prevent the Initialization Vector from being read by another application. For CBC, OFB and CFB modes, the Initialization Vector corresponds to the initialization vector. For CTR mode, it corresponds to the counter value. Note: These registers are not used in ECB mode and must not be written. SAM9M11 [DATASHEET] 1103 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44. Triple Data Encryption Standard (TDES) The Triple Data Encryption Standard (TDES) is compliant with the American FIPS (Federal Information Processing Standard) Publication 46-3 specification. The TDES supports the four different confidentiality modes of operation (ECB, CBC, OFB and CFB), specified in the FIPS (Federal Information Processing Standard) Publication 81 and is compatible with the Peripheral Data Controller channels for all of these modes, minimizing processor intervention for large buffer transfers. The 64-bit long keys and input data (and initialization vector for some modes) are each stored in two corresponding 32-bit write-only registers: Key x Word Registers TDES_KEYxWR0 and TDES_KEYxWR1 Input Data Registers TDES_IDATAR0 and TDES_IDATAR1 Initialization Vector Registers TDES_IVR0 and TDES_IVR1 As soon as the initialization vector, the input data and the key are configured, the encryption/decryption process may be started. Then the encrypted/decrypted data is ready to be read out on the two 32-bit output data registers (TDES_ODATARx) or through the PDC channels. 44.1 Embedded Characteristics  Supports Single Data Encryption Standard (DES) and Triple Data Encryption Algorithm (TDEA or TDES)  Compliant with FIPS Publication 46-3, Data Encryption Standard (DES)  64-bit Cryptographic Key for TDES  Two-key or Three-key Algorithms for TDES  18-clock Cycles Encryption/Decryption Processing Time for DES  50-clock Cycles Encryption/Decryption Processing Time for TDES  Supports eXtended Tiny Encryption Algorithm (XTEA)  128-bit key for XTEA and Programmable Round Number up to 64  Support the Four Standard Modes of Operation specified in the FIPS Publication 81, DES Modes of Operation ̶ Electronic Code Book (ECB) ̶ Cipher Block Chaining (CBC) ̶ Cipher Feedback (CFB) ̶ Output Feedback (OFB)  8-, 16-, 32- and 64-bit Data Sizes Possible in CFB Mode  Last Output Data Mode Allowing Optimized Message (Data) Authentication Code (MAC) Generation  Connection to PDC Channel Capabilities Optimizes Data Transfers for all Operating Modes ̶ One Channel for the Receiver, One Channel for the Transmitter ̶ Next Buffer Support 1104 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.2 Product Dependencies 44.2.1 Power Management The TDES may be clocked through the Power Management Controller (PMC), so the programmer must first configure the PMC to enable the TDES clock. 44.2.2 Interrupt The TDES interface has an interrupt line connected to the Advanced Interrupt Controller (AIC). Handling the TDES interrupt requires programming the AIC before configuring the TDES. 44.3 Functional Description The Data Encryption Standard (DES) and the Triple Data Encryption Algorithm (TDES) specify FIPS-approved cryptographic algorithms that can be used to protect electronic data. The TDES bit in the TDES Mode Register (TDES_MR) is used to select either the single DES or the Triple DES mode. Encryption (enciphering) converts data to an unintelligible form called ciphertext. Decrypting (deciphering) the ciphertext converts the data back into its original form, called plaintext. The CIPHER bit in the TDES_MR is used to choose between encryption and decryption. A DES is capable of using cryptographic keys of 64 bits to encrypt and decrypt data in blocks of 64 bits. This 64-bit key is defined in the Key 1 Word Registers (TDES_KEY1WRx). A TDES key consists of three DES keys, which is also referred to as a key bundle. These three 64-bit keys are defined, respectively, in the Key 1, 2 and 3 Word Registers (TDES_KEY1WRx, TDES_KEY2WRx and TDES_KEY3WRx). In Triple DES mode (TDESMOD = 1 in TDES_MR), the KEYMOD bit in the TDES_MR is used to choose between a two- and a three-key algorithm as summarized in Table 44-1. Table 44-1. TDES Algorithms Summary Data Processing Sequence Steps Algorithm Mode First Second Third Encryption Encryption with Key 1 Decryption with Key 2 Encryption with Key 3 Three-key Decryption Decryption with Key 3 Encryption with Key 2 Decryption with Key 1 Encryption Encryption with Key 1 Decryption with Key 2 Encryption with Key 1 Two-key Decryption Decryption with Key 1 Encryption with Key 2 Decryption with Key 1 The input to the encryption processes of the CBC, CFB, and OFB modes includes, in addition to the plaintext, a 64-bit data block called the initialization vector (IV), which must be set in the Initialization Vector Registers (TDES_IVRx). The initialization vector is used in an initial step in the encryption of a message and in the corresponding decryption of the message. XTEA algorithm can be used instead of DES/TDES by configuring the TDESMOD field in the TDES_MR with the appropriate value 0x2. An XTEA key consists of a 128-bit key. They are defined in the Key 1 and 2 Word Registers (TDES_KEY1WRx, TDES_KEY2WRx). The number of rounds of XTEA is defined in the TDES_XTEA_RNDR and can be programmed up to 64 (1 round = 2 Feistel network rounds). All the start and operating modes of the TDES algorithm can be applied to the XTEA algorithm. SAM9M11 [DATASHEET] 1105 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.3.1 Operation Modes The TDES supports the following modes of operation:  ECB—Electronic Code Book  CBC—Cipher Block Chaining  OFB—Output Feedback  CFB—Cipher Feedback ̶ CFB8 (CFB where the length of the data segment is 8 bits) ̶ CFB16 (CFB where the length of the data segment is 16 bits) ̶ CFB32 (CFB where the length of the data segment is 32 bits) ̶ CFB64 (CFB where the length of the data segment is 64 bits) The data pre-processing, post-processing and data chaining for each mode are automatically performed. Refer to the FIPS Publication 81 for more complete information. These modes are selected by setting the OPMOD field in the TDES_MR. In CFB mode, four data sizes are possible (8, 16, 32 and 64 bits), configurable by means of the CFBS field in the TDES_MR (see Section 44.4.2 ”TDES Mode Register” on page 1113). The OFB and CFB modes of operation are only available if 2-key mode is selected (KEYMOD=1 in TDES_MR). 44.3.2 Start Modes The SMOD field in the TDES_MR selects the encryption (or decryption) start mode. 44.3.2.1Manual Mode The sequence is as follows: 1. Write the TDES_MR with all required fields, including but not limited to SMOD and OPMOD. 2. Write the 64-bit key(s) in the different Key Word Registers (TDES_KEYxWRx), depending on whether one, two or three keys are required. 3. Write the initialization vector (or counter) in the Initialization Vector Registers (TDES_IVRx). Note: The Initialization Vector Registers concern all modes except ECB. 4. Set the bit DATRDY (Data Ready) in the TDES Interrupt Enable register (TDES_IER), depending on whether an interrupt is required or not at the end of processing. 5. Write the data to be encrypted/decrypted in the authorized Input Data Registers (see Table 44-2). 6. Set the START bit in the TDES Control Register (TDES_CR) to begin the encryption or the decryption process. 7. When the processing completes, the bit DATRDY in the TDES Interrupt Status Register (TDES_ISR) rises. If an interrupt has been enabled by setting the bit DATRDY in TDES_IER, the interrupt line of the TDES is activated. 8. When the software reads one of the Output Data Registers (TDES_ODATARx), the DATRDY bit is automatically cleared. . Table 44-2. Authorized Input Data Registers Operation Mode Input Data Registers to Write ECB All CBC All OFB All CFB 64-bit All 1106 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 44-2. Authorized Input Data Registers (Continued) Operation Mode Input Data Registers to Write CFB 32-bit TDES_IDATAR0 CFB 16-bit TDES_IDATAR0 CFB 8-bit TDES_IDATAR0 Note: In 32-, 16- and 8-bit CFB mode, writing to TDES_IDATAR1 is not allowed and may lead to errors in processing. 44.3.2.2Auto Mode The Auto Mode is similar to Manual Mode, except that, as soon as the correct number of Input Data registers is written, processing is automatically started without any action in the TDES_CR. 44.3.2.3PDC Mode The Peripheral DMA Controller (PDC) can be used in association with the TDES to perform an encryption/decryption of a buffer without any action by the software during processing. The SMOD field in the TDES_MR must be configured to 0x2. The sequence is as follows: 1. Write the TDES_MR with all required fields, including but not limited to SMOD and OPMOD. 2. Write the key in the Key Registers (TDES_KEYxWRx). 3. Write the initialization vector (or counter) in the Initialization Vector Registers (TDES_IVRx). Note: The Initialization Vector Registers concern all modes except ECB. 4. Set the PDC Transmit Pointer Register to the address where the data buffer to encrypt/decrypt is stored and the PDC Receive Pointer Register where it must be encrypted/decrypted. Note: Transmit and receive buffers can be identical. 5. Set the PDC Transmit Counter Register and PDC Receive Counter Register to the same value. This value must be a multiple of the data transfer type size (see Table 44-3 “Data Transfer Type for the Different Operation Modes”). Note: The same requirements are necessary for the Next Pointer(s) and Counter(s) of the PDC (Transmit Next Pointer Register, Receive Next Pointer Register, Transmit Next Counter Register, Receive Next Counter Register). 6. If not already done, set the ENDRX bit (or RXBUFF if the next pointers and counters are used) in the TDES_IER, depending on whether an interrupt is required or not at the end of processing. 7. Enable the PDC in transmission and reception to start the processing (PDC Transfer Control Register). 8. When the processing completes, the bit ENDRX (or RXBUFF) in the TDES_ISR rises. If an interrupt has been enabled by setting the corresponding bit in TDES_IER, the interrupt line of the TDES is activated. When PDC is used, the data size to transfer (byte, half-word or word) depends on the TDES mode of operations. This size is automatically configured by the TDES. Table 44-3. Data Transfer Type for the Different Operation Modes Operation Mode Data Transfer Type ECB Word CBC Word OFB Word CFB 64-bit Word CFB 32-bit Word CFB 16-bit Half-word CFB 8-bit Byte SAM9M11 [DATASHEET] 1107 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.3.3 Last Output Data Mode This mode is used to generate cryptographic checksums on data (MAC) using a CBC-MAC or a CFB encryption algorithm (See FIPS Publication 81 Appendix F). After each end of encryption/decryption, the output data is available either on the output data registers for Manual and Auto mode or at the address specified in the receive buffer pointer for PDC mode (See Table 44-4 “Last Output Mode Behavior versus Start Modes”). The Last Output Data bit (LOD) in the TDES_MR allows retrieval of only the last data of several encryption/decryption processes. This data is only available on the Output Data Registers (TDES_ODATARx). Therefore, there is no need to define a read buffer in PDC mode. 44.3.3.1Manual and Auto Modes TDES_MR.LOD = 0 The DATRDY flag is cleared when at least one of the Output Data Registers is read. See Figure 44-1. Figure 44-1. Manual and Auto Modes with LOD = 0 Write START bit in TDES_CR (Manual mode) or Write TDES_IDATARx register(s) (Auto mode) Read the TDES_ODATARx DATRDY Encryption or Decryption Process If the user does not want to read the output data registers between each encryption/decryption, the DATRDY flag will not be cleared. If the DATRDY flag is not cleared, the user will not be informed of the end of the encryptions/decryptions that follow. TDES_MR.LOD = 1 The DATRDY flag is cleared when at least one Input Data Register is written, before the start of a new transfer. See Figure 44-2. No further Output Data Register reads are necessary between consecutive encryptions/decryptions. Figure 44-2. Manual and Auto Modes with LOD = 1 Write START bit in TDES_CR (Manual mode) or Write TDES_IDATARx register(s) (Auto mode) Write TDES_IDATARx register(s) DATRDY Encryption or Decryption Process 1108 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.3.3.2PDC Mode TDES_MR.LOD = 0 The end of the encryption/decryption is indicated by the ENDRX (or RXBUFF) flag rise in the TDES_ISR. See Figure 44-3. Figure 44-3. PDC Mode with LOD = 0: Enable PDC Channels (Receive and Transmit Channels) Multiple Encryption or Decryption Process ENDRX (or RXBUFF) TDES_MR.LOD = 1 The user must first wait for the ENDTX (or TXBUFE) flag to rise in the TDES_ISR, then for DATRDY to ensure that the encryption/decryption is completed. See Figure 44-4. In this case, no receive buffers are required. The output data is only available on the Output Data Registers (TDES_ODATARx). Figure 44-4. PDC Mode with LOD = 1 Enable PDC Channels (only Transmit Channels) DATRDY Multiple Encryption or Decryption Process ENDTX (or TXBUFE) Table 44-4 summarizes the different cases. Table 44-4. Last Output Mode Behavior versus Start Modes Manual and Auto Modes PDC Mode Sequence LOD = 0 LOD = 1 LOD = 0 LOD = 1 DATRDY Flag At least one Output Data At least one Input Data Not used Managed by the PDC Clearing Condition (1) Register must be read Register must be written At the address Encrypted/Decrypted In the Output Data In the Output Data specified in the Receive In the Output Data Data Result Location Registers Registers Pointer Register Registers (TDES_RPR) End of ENDTX (or TXBUFE) DATRDY DATRDY ENDRX (or RXBUFF) Encryption/Decryption then DATRDY Note: 1. Depending on the mode, there are other ways of clearing the DATRDY flag. See “TDES Interrupt Status Register” on page 1118. SAM9M11 [DATASHEET] 1109 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Warning: In PDC mode, reading to the Output Data registers before the last data transfer may lead to unpredictable results. 44.3.4 Security Features 44.3.4.1Unspecified Register Access Detection When an unspecified register access occurs, the URAD bit in the TDES_ISR is set. Its source is then reported in the Unspecified Register Access Type field (URAT). Only the last unspecified register access is available through the URAT field. Several kinds of unspecified register accesses can occur:  Input Data Register written during the data processing in PDC mode  Output Data Register read during the data processing  Mode Register written during the data processing  Write-only register read access The URAD bit and the URAT field can only be reset by the SWRST bit in the TDES_CR. 1110 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.4 Triple Data Encryption Standard (TDES) User Interface Table 44-5. Register Mapping Offset Register Name Access Reset 0x00 Control Register TDES_CR Write-only – 0x04 Mode Register TDES_MR Read/Write 0x2 0x08–0x0C Reserved – – – 0x10 Interrupt Enable Register TDES_IER Write-only – 0x14 Interrupt Disable Register TDES_IDR Write-only – 0x18 Interrupt Mask Register TDES_IMR Read-only 0x0 0x1C Interrupt Status Register TDES_ISR Read-only 0x0000001E 0x20 Key 1 Word Register 0 TDES_KEY1WR0 Write-only – 0x24 Key 1 Word Register 1 TDES_KEY1WR1 Write-only – 0x28 Key 2 Word Register 0 TDES_KEY2WR0 Write-only – 0x2C Key 2 Word Register 1 TDES_KEY2WR1 Write-only – 0x30 Key 3 Word Register 0 TDES_KEY3WR0 Write-only – 0x34 Key 3 Word Register 1 TDES_KEY3WR1 Write-only – 0x38–0x3C Reserved – – – 0x40 Input Data Register 0 TDES_IDATAR0 Write-only – 0x44 Input Data Register 1 TDES_IDATAR1 Write-only – 0x48–0x4C Reserved – – – 0x50 Output Data Register 0 TDES_ODATAR0 Read-only 0x0 0x54 Output Data Register 1 TDES_ODATAR1 Read-only 0x0 0x58–0x5C Reserved – – – 0x60 Initialization Vector Register 0 TDES_IVR0 Write-only – 0x64 Initialization Vector Register 1 TDES_IVR1 Write-only – 0x70 XTEA Rounds Register TDES_XTEA_RNDR – – 0x68–0xFC Reserved – – – 0x100–0x124 Reserved for the PDC – – – SAM9M11 [DATASHEET] 1111 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.4.1 TDES Control Register Name: TDES_CR Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – SWRST 7 6 5 4 3 2 1 0 – – – – – – – START • START: Start Processing 0: No effect 1: Starts Manual encryption/decryption process. • SWRST: Software Reset 0: No effect. 1: Resets the TDES. A software triggered hardware reset of the TDES interface is performed. 1112 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.4.2 TDES Mode Register Name: TDES_MR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – CFBS 15 14 13 12 11 10 9 8 LOD – OPMOD – – SMOD 7 6 5 4 3 2 1 0 – – – KEYMOD – TDESMOD CIPHER • CIPHER: Processing Mode 0 (DECRYPT): Decrypts data. 1 (ENCRYPT): Encrypts data. • TDESMOD: ALGORITHM mode Value Name Description 0x0 SINGLE_DES Single DES processing using TDES_KEY1WRx registers 0x1 TRIPLE_DES Triple DES processing using TDES_KEY1WRx, TDES_KEY2WRx and TDES_KEY3WRx registers 0x2 XTEA XTEA processing using TDES_KEY1WRx, TDES_KEY2WRx Values which are not listed in table must be considered as “reserved”. • KEYMOD: Key Mode 0: Three-key algorithm is selected. 1: Two-key algorithm is selected. There is no need to write TDES_KEY3WRx registers. • SMOD: Start Mode Value Name Description 0x0 MANUAL_START Manual Mode 0x1 AUTO_START Auto Mode 0x2 IDATAR0_START TDES_IDATAR0 access only Auto Mode Values which are not listed in the table must be considered as “reserved”. If a PDC transfer is used, it is mandatory to set SMOD to 0x2. Refer to Section 44.3.3.2 ”PDC Mode” for more details. • OPMOD: Operation Mode Value Name Description 0x0 ECB Electronic Code Book mode 0x1 CBC Cipher Block Chaining mode 0x2 OFB Output Feedback mode 0x3 CFB Cipher Feedback mode For CBC-MAC operating mode, please set OPMOD to CBC and LOD to 1. The OFB and CFB modes of operation are only available if 2-key mode is selected (KEYMOD = 1). SAM9M11 [DATASHEET] 1113 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• LOD: Last Output Data Mode 0: No effect. After each end of encryption/decryption, the output data is available either on the output data registers (Manual and Auto modes) or at the address specified in the receive buffer pointer (PDC mode). In Manual and Auto modes, the DATRDY flag is cleared when at least one of the Output Data registers is read. 1: The DATRDY flag is cleared when at least one of the Input Data Registers is written. No more Output Data Register reads are necessary between consecutive encryptions/decryptions (See “Last Output Data Mode” on page 1108.). Warning: In PDC mode, reading to the Output Data registers before the last data encryption/decryption process may lead to unpredictable result. • CFBS: Cipher Feedback Data Size Value Name Description 0x0 SIZE_64BIT 64-bit 0x1 SIZE_32BIT 32-bit 0x2 SIZE_16BIT 16-bit 0x3 SIZE_8BIT 8-bit 1114 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.4.3 TDES Interrupt Enable Register Name: TDES_IER Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – URAD 7 6 5 4 3 2 1 0 – – – TXBUFE RXBUFF ENDTX ENDRX DATRDY • DATRDY: Data Ready Interrupt Enable 0: No effect. 1: Enables the corresponding interrupt. • ENDRX: End of Receive Buffer Interrupt Enable 0: No effect. 1: Enables the corresponding interrupt. • ENDTX: End of Transmit Buffer Interrupt Enable 0: No effect. 1: Enables the corresponding interrupt. • RXBUFF: Receive Buffer Full Interrupt Enable 0: No effect. 1: Enables the corresponding interrupt. • TXBUFE: Transmit Buffer Empty Interrupt Enable 0: No effect. 1: Enables the corresponding interrupt. • URAD: Unspecified Register Access Detection Interrupt Enable 0: No effect. 1: Enables the corresponding interrupt. SAM9M11 [DATASHEET] 1115 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.4.4 TDES Interrupt Disable Register Name: TDES_IDR Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – URAD 7 6 5 4 3 2 1 0 – – – TXBUFE RXBUFF ENDTX ENDRX DATRDY • DATRDY: Data Ready Interrupt Disable 0: No effect. 1: Disables the corresponding interrupt. • ENDRX: End of Receive Buffer Interrupt Disable 0: No effect. 1: Disables the corresponding interrupt. • ENDTX: End of Transmit Buffer Interrupt Disable 0: No effect. 1: Disables the corresponding interrupt. • RXBUFF: Receive Buffer Full Interrupt Disable 0: No effect. 1: Disables the corresponding interrupt. • TXBUFE: Transmit Buffer Empty Interrupt Disable 0: No effect. 1: Disables the corresponding interrupt. • URAD: Unspecified Register Access Detection Interrupt Disable 0: No effect. 1: Disables the corresponding interrupt. 1116 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.4.5 TDES Interrupt Mask Register Name: TDES_IMR Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – URAD 7 6 5 4 3 2 1 0 – – – TXBUFE RXBUFF ENDTX ENDRX DATRDY • DATRDY: Data Ready Interrupt Mask 0: The corresponding interrupt is not enabled. 1: The corresponding interrupt is enabled. • ENDRX: End of Receive Buffer Interrupt Mask 0: The corresponding interrupt is not enabled. 1: The corresponding interrupt is enabled. • ENDTX: End of Transmit Buffer Interrupt Mask 0: The corresponding interrupt is not enabled. 1: The corresponding interrupt is enabled. • RXBUFF: Receive Buffer Full Interrupt Mask 0: The corresponding interrupt is not enabled. 1: The corresponding interrupt is enabled. • TXBUFE: Transmit Buffer Empty Interrupt Mask 0: The corresponding interrupt is not enabled. 1: The corresponding interrupt is enabled. • URAD: Unspecified Register Access Detection Interrupt Mask 0: The corresponding interrupt is not enabled. 1: The corresponding interrupt is enabled. SAM9M11 [DATASHEET] 1117 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.4.6 TDES Interrupt Status Register Name: TDES_ISR Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 URAT – – – URAD 7 6 5 4 3 2 1 0 – – – TXBUFE RXBUFF ENDTX ENDRX DATRDY • DATRDY: Data Ready 0: Output data is not valid. 1: Encryption or decryption process is completed. DATRDY is cleared when a Manual encryption/decryption occurs (START bit in TDES_CR) or when a software triggered hardware reset of the TDES interface is performed (SWRST bit in TDES_CR). LOD = 0 (TDES_MR): In Manual and Auto mode, the DATRDY flag can also be cleared when at least one of the Output Data Registers is read. In PDC mode, DATRDY is set and cleared automatically. LOD = 1 (TDES_MR): In Manual and Auto mode, the DATRDY flag can also be cleared when at least one of the Input Data Registers is written. In PDC mode, DATRDY is set and cleared automatically. • ENDRX: End of RX Buffer 0: The Receive Counter Register has not reached 0 since the last write in TDES_RCR or TDES_RNCR. 1: The Receive Counter Register has reached 0 since the last write in TDES_RCR or TDES_RNCR. Note: This flag must be used only in PDC mode with LOD bit cleared. • ENDTX: End of TX Buffer 0: The Transmit Counter Register has not reached 0 since the last write in TDES_TCR or TDES_TNCR. 1: The Transmit Counter Register has reached 0 since the last write in TDES_TCR or TDES_TNCR. Note: This flag must be used only in PDC mode with LOD bit set. • RXBUFF: RX Buffer Full 0: TDES_RCR or TDES_RNCR has a value other than 0. 1: Both TDES_RCR and TDES_RNCR have a value of 0. Note: This flag must be used only in PDC mode with LOD bit cleared. • TXBUFE: TX Buffer Empty 0: TDES_TCR or TDES_TNCR has a value other than 0. 1: Both TDES_TCR and TDES_TNCR have a value of 0. Note: This flag must be used only in PDC mode with LOD bit set. 1118 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• URAD: Unspecified Register Access Detection Status 0: No unspecified register access has been detected since the last write of bit TDES_CR.SWRST. 1: At least one unspecified register access has been detected since the last write of bit TDES_CR.SWRST. URAD bit is reset only by the SWRST bit in the TDES_CR. • URAT: Unspecified Register Access Value Name Description 0x0 IDR_WR_PROCESSING Input Data Register written during the data processing when SMOD = 0x2 mode. 0x1 ODR_RD_PROCESSING Output Data Register read during the data processing. 0x2 MR_WR_PROCESSING Mode Register written during the data processing. 0x3 WOR_RD_ACCESS Write-only register read access. Only the last Unspecified Register Access Type is available through the URAT field. URAT field is reset only by the SWRST bit in the TDES_CR. SAM9M11 [DATASHEET] 1119 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.4.7 TDES Key 1 Word Register x Name: TDES_KEY1WRx Access: Write-only 31 30 29 28 27 26 25 24 KEY1W 23 22 21 20 19 18 17 16 KEY1W 15 14 13 12 11 10 9 8 KEY1W 7 6 5 4 3 2 1 0 KEY1W • KEY1W: Key 1 Word The two 32-bit Key 1 Word Registers allow to set the 64-bit cryptographic key used for encryption/decryption. KEY1W0 corresponds to the first word of the key and KEY1W1 to the last one. These registers are write-only to prevent the key from being read by another application. In XTEA mode, the key is defined on 128 bits. These registers contain the 64 LSB bits of the encryption/decryption key. 1120 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.4.8 TDES Key 2 Word Register x Name: TDES_KEY2WRx Access: Write-only 31 30 29 28 27 26 25 24 KEY2W 23 22 21 20 19 18 17 16 KEY2W 15 14 13 12 11 10 9 8 KEY2W 7 6 5 4 3 2 1 0 KEY2W • KEY2W: Key 2 Word The two 32-bit Key 2 Word Registers allow to set the 64-bit cryptographic key used for encryption/decryption. KEY2W0 corresponds to the first word of the key and KEY2W1 to the last one. These registers are write-only to prevent the key from being read by another application. Note: KEY2WRx registers are not used in DES mode. In XTEA mode, the key is defined on 128 bits. These registers contain the 64 MSB bits of the encryption/decryption key. SAM9M11 [DATASHEET] 1121 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.4.9 TDES Key 3 Word Register x Name: TDES_KEY3WRx Access: Write-only 31 30 29 28 27 26 25 24 KEY3W 23 22 21 20 19 18 17 16 KEY3W 15 14 13 12 11 10 9 8 KEY3W 7 6 5 4 3 2 1 0 KEY3W • KEY3W: Key 3 Word The two 32-bit Key 3 Word Registers allow to set the 64-bit cryptographic key used for encryption/decryption. KEY3W0 corresponds to the first word of the key and KEY3W1 to the last one. These registers are write-only to prevent the key from being read by another application. Note: KEY3WRx registers are not used in DES mode, TDES with two-key algorithm selected and XTEA Mode. 1122 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.4.10TDES Input Data Register x Name: TDES_IDATARx Access: Write-only 31 30 29 28 27 26 25 24 IDATA 23 22 21 20 19 18 17 16 IDATA 15 14 13 12 11 10 9 8 IDATA 7 6 5 4 3 2 1 0 IDATA • IDATA: Input Data The two 32-bit Input Data registers allow to set the 64-bit data block used for encryption/decryption. IDATA0 corresponds to the first word of the data to be encrypted/decrypted, and IDATA1 to the last one. These registers are write-only to prevent the input data from being read by another application. SAM9M11 [DATASHEET] 1123 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.4.11 TDES Output Data Register x Name: TDES_ODATARx Access: Read-only 31 30 29 28 27 26 25 24 ODATA 23 22 21 20 19 18 17 16 ODATA 15 14 13 12 11 10 9 8 ODATA 7 6 5 4 3 2 1 0 ODATA • ODATA: Output Data The two 32-bit Output Data registers contain the 64-bit data block which has been encrypted/decrypted. ODATA1 corresponds to the first word, ODATA2 to the last one. 1124 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.4.12TDES Initialization Vector Register x Name: TDES_IVRx Access: Write-only 31 30 29 28 27 26 25 24 IV 23 22 21 20 19 18 17 16 IV 15 14 13 12 11 10 9 8 IV 7 6 5 4 3 2 1 0 IV • IV: Initialization Vector The two 32-bit Initialization Vector registers are used to set the 64-bit initialization vector data block, which is used by some modes of operation as an additional initial input. IV1 corresponds to the first word of the Initialization Vector, IV2 to the last one. These registers are write-only to prevent the Initialization Vector from being read by another application. Note: These registers are not used for ECB mode and must not be written. SAM9M11 [DATASHEET] 1125 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.4.13TDES XTEA Rounds Register Name: TDES_XTEA_RNDR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – XTEA_RNDS • XTEA_RNDS: Number of Rounds This 6-bit field is used to define the number of complete rounds (1 complete round = 2 Feistel rounds) processed in XTEA algorithm. The value, XTEA_RNDS has no effect if TDESMOD field of TDES_MR is set to 0x0 or 0x1. Note: 0x00 corresponds to 1 complete round, 0x01 corresponds to 2 complete rounds, etc... 1126 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

45. Secure Hash Algorithm (SHA) 45.1 Description The Secure Hash Algorithm (SHA) is compliant with the American FIPS (Federal Information Processing Standard) Publication 180-2 specification. The 512-bit block of message is stored in 16 x 32-bit registers (SHA_IDATAxR) which are all write-only, by software or through PDC channels. As soon as the input data (512-bit block) is written, the hash processing may be started. The registers comprising the 512-bit block of a padded message must be entered consecutively. Then the message digest is ready to be read out on the 5 up to 8 x 32-bit output data registers (SHA_ODATAxR), by software only. 45.2 Embedded Characteristics  Supports Secure Hash Algorithm (SHA1 and SHA256)  Compliant with FIPS Publication 180-2  Configurable Processing Period: ̶ 85 Clock Cycles to Maximize the Bandwidth for SHA1 or 386 Clock Cycles or Other Applications in PDC (Peripheral DMA) ̶ 72 Clock Cycles to Maximize the Bandwidth for SHA256 or 265 Clock Cycles or Other Applications in PDC (Peripheral DMA)  Connection to PDC Channel Capabilities Optimizes Data Transfers ̶ One Channel for the Transmitter ̶ Next Buffer Support 45.3 Product Dependencies 45.3.1 Power Management The SHA may be clocked through the Power Management Controller (PMC), so the programmer must first configure the PMC to enable the SHA clock. 45.3.2 Interrupt The SHA interface has an interrupt line connected to the Advanced Interrupt Controller (AIC). Handling the SHA interrupt requires programming the AIC before configuring the SHA. SAM9M11 [DATASHEET] 1127 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

45.4 Functional Description The Secure Hash Algorithm (SHA) module requires a padded message according to FIPS180-2 specification. The first block of the message must be indicated to the module. The SHA module produces a 160-bit message digest each time a block is written in SHA1 mode or a 256-bit message digest each time a block is written in SHA256 mode. 45.4.1 SHA Algorithm The module can process SHA1 or SHA256 by means of a configuration bit. 45.4.2 Processing Period The processing period can be configured. The short processing period allows to allocate bandwidth to the SHA module whereas the long processing period allocates more bandwidth to other applications (example: PDC). In SHA1 mode, the short processing period is 85 clock cycles + 2 clock cycles for start command synchronization. The long period is 326 clock cycles + 2 clock cycles. In SHA256 mode, the short processing period is 72 clock cycles + 2 clock cycles for start command synchronization. The long period is 265 clock cycles + 2 clock cycles. 45.4.3 Start Modes The SMOD field in the SHA Mode Register (SHA_MR) is used to select the hash processing start mode. 45.4.3.1Manual Mode The sequence is as follows:  Set the bit DATRDY (Data Ready) in the SHA Interrupt Enable Register (SHA_IER), depending on whether an interrupt is required or not at the end of processing.  For the first 512-bit block of a message, the FIRST command must be set by writing a 1 into the corresponding bit of the Control Register (SHA_CR). For the other blocks, there is nothing to write in this Control Register.  Write the 512-bit block to be processed in the Input Data Registers.  Set the START bit in the SHA Control Register SHA_CR to begin the processing.  When the processing completes, the bit DATRDY in the SHA Interrupt Status Register (SHA_ISR) raises. If an interrupt has been enabled by setting the bit DATRDY in SHA_IER, the interrupt line of the SHA is activated.  Repeat the write procedure for each 512-bit block, start procedure and wait for the interrupt procedure up to the last 512-bit block of the entire message. Each time the start procedure is complete, the DATRDY flag is cleared.  After the last block is processed (DATRDY flag is set, if an interrupt has been enabled by setting the bit DATRDY in SHA_IER, the interrupt line of the SHA is activated), read the message digest in the Output Data Registers. The DATRDY flag is automatically cleared when reading the SHA_ODATAxR read only registers. 45.4.3.2Auto Mode Auto Mode is similar to Manual Mode, except that in this mode, as soon as the correct number of Input Data Registers is written, processing is automatically started without any action in the control register. 45.4.3.3PDC Mode The Peripheral Data Controller (PDC or Peripheral DMA) can be used in association with the SHA to perform the algorithm on a complete message without any action by the software during processing. In this starting mode, the type of the data transfer is set in words: 1128 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The sequence is as follows:  Set the Transmit Pointer Register (SHA_TPR) to the address where the data buffer to process is stored.  Set the Transmit Counter Registers (SHA_TCR) to the same value. This value must be a multiple of words. Note: The same requirements are necessary for the Next Pointer(s) and Counter(s) of the PDC (SHA_TNPR, SHA_TNCR).  If not already done, set the bit ENDTX (or TXBUFF if the next pointers and counters are used) in the SHA Interrupt Enable Register (SHA_IER), depending on whether an interrupt is required or not at the end of processing.  If not already done, set the bit DATRDY in SHA Interrupt Enable Register (SHA_IER).  Enable the PDC in transmission to start the processing (SHA_PTCR).  When the processing completes, the bit ENDTX (or TXBUFF) in the SHA Interrupt Status Register (SHA_ISR) raises. If an interrupt has been enabled by setting the corresponding in SHA_IER, the interrupt line of the SHA is activated.  As soon as bit ENDTX (or TXBUFF) or interrupt is triggered, the DATRDY bit or interrupt line must be triggered.  The message digest can be read from the Output Data Registers (SHA_ODATAxR read only registers). 45.4.4 Security Features When an unspecified register access occurs, the URAD bit in the Interrupt Status Register (SHA_ISR) raises. Its source is then reported in the Unspecified Register Access Type field (URAT). Only the last unspecified register access is available through the URAT field. Several kinds of unspecified register accesses can occur:  Input Data Register written during the data processing in PDC mode  Output Data Register read during the data processing  Mode Register written during the data processing  Write-only register read access The URAD bit and the URAT field can only be reset by the SWRST bit in the SHA_CR. SAM9M11 [DATASHEET] 1129 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

45.5 Secure Hash Algorithm (SHA) User Interface Table 45-1. Register Mapping Offset Register Name Access Reset 0x00 Control Register SHA_CR Write-only – 0x04 Mode Register SHA_MR Read/Write 0x1 0x08–0x0C Reserved – – – 0x10 Interrupt Enable Register SHA_IER Write-only – 0x14 Interrupt Disable Register SHA_IDR Write-only – 0x18 Interrupt Mask Register SHA_IMR Read-only 0x0 0x1C Interrupt Status Register SHA_ISR Read-only 0x0000000A 0x20–0x3C Reserved – 0x40 Input Data 1 Register SHA_IDATA1R Write-only – 0x44 Input Data 2 Register SHA_IDATA2R Write-only – 0x48 Input Data 3 Register SHA_IDATA3R Write-only – 0x4C Input Data 4 Register SHA_IDATA4R Write-only – 0x50 Input Data 5 Register SHA_IDATA5R Write-only – 0x54 Input Data 6Register SHA_IDATA6R Write-only – 0x58 Input Data 7 Register SHA_IDATA7R Write-only – 0x5C Input Data 8 Register SHA_IDATA8R Write-only – 0x60 Input Data 9 Register SHA_IDATA9R Write-only – 0x64 Input Data 10 Register SHA_IDATA10R Write-only – 0x68 Input Data 11 Register SHA_IDATA11R Write-only – 0x6C Input Data 12 Register SHA_IDATA12R Write-only – 0x70 Input Data 13 Register SHA_IDATA13R Write-only – 0x74 Input Data 14 Register SHA_IDATA14R Write-only – 0x78 Input Data 15 Register SHA_IDATA15R Write-only – 0x7C Input Data 16 Register SHA_IDATA16R Write-only – 0x80 Output Data 1 Register SHA_ODATA1R Read-only 0x0 0x84 Output Data 2 Register SHA_ODATA2R Read-only 0x0 0x88 Output Data 3 Register SHA_ODATA3R Read-only 0x0 0x8C Output Data 4 Register SHA_ODATA4R Read-only 0x0 0x90 Output Data 5Register SHA_ODATA5R Read-only 0x0 0x94 Output Data 6Register SHA_ODATA6R Read-only 0x0 0x98 Output Data 7Register SHA_ODATA7R Read-only 0x0 0x9C Output Data 8Register SHA_ODATA8R Read-only 0x0 0x94–0xFC Reserved – – – 0x100–0x124 Reserved for the PDC – – – 1130 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

45.5.1 SHA Control Register Name: SHA_CR Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – SWRST 7 6 5 4 3 2 1 0 – – – FIRST – – – START • START: Start Processing 0: No effect 1: Starts Manual hash algorithm process • FIRST: First Block of a Message 0: No effect 1: Indicates that the next 512-block to process is the first one of a message. • SWRST: Software Reset 0: No effect. 1: Resets the SHA. A software triggered hardware reset of the SHA interface is performed. SAM9M11 [DATASHEET] 1131 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

45.5.2 SHA Mode Register Name: SHA_MR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – ALGO 7 6 5 4 3 2 1 0 – PROCDLY – – SMOD • SMOD: Start Mode Value Description 0 0 Manual Mode 0 1 Auto Mode 1 0 PDC Mode 1 1 Reserved • PROCDLY: Processing Delay 0: The processing period is 85 or 72clock cycles. The bandwidth allocated for the SHA on the system bus is maximized in PDC mode. 1: The processing period is 326 or 265 clock cycles. The bandwidth allocated for the other applications on the system bus is maximized in particular when PDC mode is set to SHA. When SHA1 algorithm is processed, processing periods are either 85 or 326 clock cycles. When SHA256 algorithm is processed, processing periods are either 72 or 265clock cycles. • ALGO: SHA Algorithm 0: The SHA1 algorithm is selected. 1: The SHA256 algorithm is selected. 1132 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

45.5.3 SHA Interrupt Enable Register Name: SHA_IER Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – URAD 7 6 5 4 3 2 1 0 – – – – – TXBUFE ENDTX DATRDY • DATRDY: Data Ready Interrupt Enable • ENDTX: End of Transmit Buffer Interrupt Enable • TXBUFE: Transmit Buffer Empty Interrupt Enable • URAD: Unspecified Register Access Detection Interrupt Enable 0: No effect. 1: Enables the corresponding interrupt. SAM9M11 [DATASHEET] 1133 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

45.5.4 SHA Interrupt Disable Register Name: SHA_IDR Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – URAD 7 6 5 4 3 2 1 0 – – – – – TXBUFE ENDTX DATRDY • DATRDY: Data Ready Interrupt Disable • ENDTX: End of Transmit Buffer Interrupt Disable • TXBUFE: Transmit Buffer Empty Interrupt Disable • URAD: Unspecified Register Access Detection Interrupt Disable 0: No effect. 1: Disables the corresponding interrupt. 1134 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

45.5.5 SHA Interrupt Mask Register Name: SHA_IMR Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – URAD 7 6 5 4 3 2 1 0 – – – – – TXBUFE ENDTX DATRDY • DATRDY: Data Ready Interrupt Mask • ENDTX: End of Transmit Buffer Interrupt Mask • TXBUFE: Transmit Buffer Empty Interrupt Mask • URAD: Unspecified Register Access Detection Interrupt Mask 0: The corresponding interrupt is not enabled. 1: The corresponding interrupt is enabled. SAM9M11 [DATASHEET] 1135 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

45.5.6 SHA Interrupt Status Register Name: SHA_ISR Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 URAT – – – URAD 7 6 5 4 3 2 1 0 – – – – – TXBUFE ENDTX DATRDY • DATRDY: Data Ready 0: Output data is not valid. 1: 512-bit block process is completed. DATRDY is cleared when a Manual process occurs (START bit in SHA_CR) or when a software triggered hardware reset of the SHA interface is performed (SWRST bit in SHA_CR). • ENDTX: End of TX Buffer 0: The Transmit Counter Register has not reached 0 since the last write in SHA_TCR or SHA_TNCR. 1: The Transmit Counter Register has reached 0 since the last write in SHA_TCR or SHA_TNCR. • TXBUFE: TX Buffer Empty 0: SHA_TCR or SHA_TNCR has a value other than 0. 1: Both SHA_TCR and SHA_TNCR have a value of 0. • URAD: Unspecified Register Access Detection Status 0: No unspecified register access has been detected since the last SWRST. 1: At least one unspecified register access has been detected since the last SWRST. URAD bit is reset only by the SWRST bit in the SHA_CR. • URAT: Unspecified Register Access Type Value Description 0 0 0 Input Data Register written during the data processing in PDC mode 0 0 1 Output Data Register read during the data processing 0 1 0 Mode Register written during the data processing 1 0 1 Write-only register read access. Only the last Unspecified Register Access Type is available through the URAT field. URAT field is reset only by the SWRST bit in the SHA_CR. 1136 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

45.5.7 SHA Input Data x Register Name: SHA_IDATAxR Access: Write-only 31 30 29 28 27 26 25 24 IDATAx 23 22 21 20 19 18 17 16 IDATAx 15 14 13 12 11 10 9 8 IDATAx 7 6 5 4 3 2 1 0 IDATAx • IDATAx: Input Data x The two 32-bit Input Data registers allow to set the 512-bit data block used for hash processing. IDATA1 corresponds to the first word of the 512-bit block, and IDATA16 to the last one. These registers are write-only to prevent the input data from being read by another application. SAM9M11 [DATASHEET] 1137 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

45.5.8 SHA Output Data x Register Name: SHA_ODATAxR Access: Read-only 31 30 29 28 27 26 25 24 ODATAx 23 22 21 20 19 18 17 16 ODATAx 15 14 13 12 11 10 9 8 ODATAx 7 6 5 4 3 2 1 0 ODATAx • ODATAx: Output Data x The 5 up to 8 32-bit Output Data registers contain the 160-bit or 256-bit message digest depending on the SHA algorithm selected. ODATA1 corresponds to the first word, ODATA7 to the last one in SHA256 mode or ODATA5 is the last one in SHA1 mode. 1138 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

46. True Random Number Generator (TRNG) 46.1 Description The True Random Number Generator (TRNG) passes the American NIST Special Publication 800-22 and Diehard Random Tests Suites. As soon as the TRNG is enabled (TRNG_CTRL register), the generator provides one 32-bit value every 84 clock cycles. Interrupt trng_int can be enabled through the TRNG_IER (respectively disabled in TRNG_IDR). This interrupt is set when a new random value is available and is cleared when the status register is read (TRNG_SR). The flag DATRDY of the status register (TRNG_ISR) is set when the random data is ready to be read out on the 32-bit output data register (TRNG_ODATA). The normal mode of operation checks that the status register flag equals 1 before reading the output data register when a 32-bit random value is required by the software application. Figure 46-1. TRNG Data Generation Sequence clock trng_cr enable 84 clock cycles 84 clock cycles 84 clock cycles trng_int Read TRNG_ISR Read TRNG_ISR Read TRNG_ODATA Read TRNG_ODATA SAM9M11 [DATASHEET] 1139 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

46.2 True Random Number Generator (TRNG) User Interface Table 46-1. Register Mapping Offset Register Name Access Reset 0x00 Control Register TRNG_CR Write-only – 0x10 Interrupt Enable Register TRNG_IER Write-only – 0x14 Interrupt Disable Register TRNG_IDR Write-only – 0x18 Interrupt Mask Register TRNG_IMR Read-only 0x0000 0x1C Interrupt Status Register TRNG_ISR Read-only 0x0000 0x50 Output Data Register TRNG_ODATA Read-only 0x0000 1140 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

46.2.1 TRNG Control Register Name: TRNG_CR Address: 0xFFFCC000 Access: Write-only 31 30 29 28 27 26 25 24 KEY 23 22 21 20 19 18 17 16 KEY 15 14 13 12 11 10 9 8 KEY 7 6 5 4 3 2 1 0 – – – – – – – ENABLE • ENABLE: Enables the TRNG to provide random values 0: Disables the TRNG. 1: Enables the TRNG. • KEY: Security Key KEY = 0x524e47 (RNG in ASCII). This key is to be written when the ENABLE bit is set or cleared. SAM9M11 [DATASHEET] 1141 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

46.2.2 TRNG Interrupt Enable Register Name: TRNG_IER Address: 0xFFFCC010 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – DATRDY • DATRDY: Data Ready Interrupt Enable 0: No effect. 1: Enables the corresponding interrupt. 1142 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

46.2.3 TRNG Interrupt Disable Register Name: TRNG_IDR Address: 0xFFFCC014 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – DATRDY • DATRDY: Data Ready Interrupt Disable 0: No effect. 1: Disables the corresponding interrupt. SAM9M11 [DATASHEET] 1143 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

46.2.4 TRNG Interrupt Mask Register Name: TRNG_IMR Address: 0xFFFCC018 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – DATRDY • DATRDY: Data Ready Interrupt Mask 0: The corresponding interrupt is not enabled. 1: The corresponding interrupt is enabled. 1144 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

46.2.5 TRNG Interrupt Status Register Name: TRNG_ISR Address: 0xFFFCC01C Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – DATRDY • DATRDY: Data Ready 0: Output data is not valid or TRNG is disabled. 1: New Random value is completed. DATRDY is cleared when this register is read. SAM9M11 [DATASHEET] 1145 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

46.2.6 TRNG Output Data Register Name: TRNG_ODATA Address: 0xFFFCC050 Access: Read-only 31 30 29 28 27 26 25 24 ODATA 23 22 21 20 19 18 17 16 ODATA 15 14 13 12 11 10 9 8 ODATA 7 6 5 4 3 2 1 0 ODATA • ODATA: Output Data The 32-bit Output Data register contains the 32-bit random data. 1146 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47. LCD Controller (LCDC) 47.1 Description The LCD Controller (LCDC) consists of logic for transferring LCD image data from an external display buffer to an LCD module with integrated common and segment drivers. The LCD Controller supports single and double scan monochrome and color passive STN LCD modules and single scan active TFT LCD modules. On monochrome STN displays, up to 16 gray shades are supported using a time-based dithering algorithm and Frame Rate Control (FRC) method. This method is also used in color STN displays to generate up to 4096 colors. The LCD Controller has a display input buffer (FIFO) to allow a flexible connection of the external AHB master interface, and a lookup table to allow palettized display configurations. The LCD Controller is programmable in order to support many different requirements such as resolutions up to 2048 x 2048; pixel depth (1, 2, 4, 8, 16, 24 bits per pixel); data line width (4, 8, 16 or 24 bits) and interface timing. The LCD Controller is connected to the ARM Advanced High Performance Bus (AHB) as a master for reading pixel data. However, the LCD Controller interfaces with the AHB as a slave in order to configure its registers. 47.2 Embedded Characteristics  Single and Dual scan color and monochrome passive STN LCD panels supported  Single scan active TFT LCD panels supported.  4-bit single scan, 8-bit single or dual scan, 16-bit dual scan STN interfaces supported  Up to 24-bit single scan TFT interfaces supported  Up to 16 gray levels for mono STN and up to 4096 colors for color STN displays  1, 2 bits per pixel (palettized), 4 bits per pixel (non-palettized) for mono STN  1, 2, 4, 8 bits per pixel (palettized), 16 bits per pixel (non-palettized) for color STN  1, 2, 4, 8 bits per pixel (palettized), 16, 24 bits per pixel (non-palettized) for TFT  Single clock domain architecture  Resolution supported up to 2048 x 2048 SAM9M11 [DATASHEET] 1147 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.3 Block Diagram Figure 47-1. LCD Macrocell Block Diagram AHB MASTER AHB SLAVE DMA Controller SPLIT AHB IF CFG AHB SLAVE DMA Data Dvalid Dvalid CTRL CH-U CH-L Upper Push Lower Push Input Interface LCD Controller Core FIFO Configuration IF CFG AHB SLAVE SERIALIZER H T A LUT Mem Interface AP PALETTE LUT Mem Interface T FIFO Mem Interface A D Control Interface DITHERING FIFO LUT MEM MEM OUTPUT Time SHIFTER Generator DISPLAY IF LCDD Control signals Display PWM DISPLAY IF 1148 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.4 I/O Lines Description Table 47-1. I/O Lines Description Name Description Type LCDCC Contrast control signal Output LCDHSYNC Line synchronous signal (STN) or Horizontal synchronous signal (TFT) Output LCDDOTCK LCD clock signal (STN/TFT) Output LCDVSYNC Frame synchronous signal (STN) or Vertical synchronization signal (TFT) Output LCDDEN Data enable signal Output LCDMOD LCD Modulation signal Output LCDPWR LCD panel power enable control signal Output LCDD[23:0] LCD Data Bus output Output 47.5 Product Dependencies 47.5.1 I/O Lines The pins used for interfacing the LCD Controller may be multiplexed with PIO lines. The programmer must first program the PIO Controller to assign the pins to their peripheral function. If I/O lines of the LCD Controller are not used by the application, they can be used for other purposes by the PIO Controller. Table 47-2. I/O Lines Instance Signal I/O Line Peripheral LCDC LCDCC PE2 A LCDC LCDDEN PE6 A LCDC LCDDOTCK PE5 A LCDC LCDD0 PE7 A LCDC LCDD1 PE8 A LCDC LCDD2 PE7 B LCDC LCDD2 PE9 A LCDC LCDD3 PE8 B LCDC LCDD3 PE10 A LCDC LCDD4 PE9 B LCDC LCDD4 PE11 A LCDC LCDD5 PE10 B LCDC LCDD5 PE12 A LCDC LCDD6 PE11 B LCDC LCDD6 PE13 A LCDC LCDD7 PE12 B LCDC LCDD7 PE14 A LCDC LCDD8 PE15 A LCDC LCDD9 PE16 A SAM9M11 [DATASHEET] 1149 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 47-2. I/O Lines (Continued) Instance Signal I/O Line Peripheral LCDC LCDD10 PE13 B LCDC LCDD10 PE17 A LCDC LCDD11 PE14 B LCDC LCDD11 PE18 A LCDC LCDD12 PE15 B LCDC LCDD12 PE19 A LCDC LCDD13 PE16 B LCDC LCDD13 PE20 A LCDC LCDD14 PE17 B LCDC LCDD14 PE21 A LCDC LCDD15 PE18 B LCDC LCDD15 PE22 A LCDC LCDD16 PE23 A LCDC LCDD17 PE24 A LCDC LCDD18 PE19 B LCDC LCDD18 PE25 A LCDC LCDD19 PE20 B LCDC LCDD19 PE26 A LCDC LCDD20 PE21 B LCDC LCDD20 PE27 A LCDC LCDD21 PE22 B LCDC LCDD21 PE28 A LCDC LCDD22 PE23 B LCDC LCDD22 PE29 A LCDC LCDD23 PE24 B LCDC LCDD23 PE30 A LCDC LCDHSYNC PE4 A LCDC LCDMOD PE1 A LCDC LCDPWR PE0 A LCDC LCDVSYNC PE3 A 47.5.2 Power Management The LCD Controller is not continuously clocked. The user must first enable the LCD Controller clock in the Power Management Controller before using it (PMC_PCER). 1150 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.5.3 Interrupt Sources The LCD Controller interrupt line is connected to one of the internal sources of the Advanced Interrupt Controller. Using the LCD Controller interrupt requires prior programming of the AIC. Table 47-3. Peripheral IDs Instance ID LCDC 23 47.6 Functional Description The LCD Controller consists of two main blocks (Figure 47-1 on page 1148), the DMA controller and the LCD controller core (LCDC core). The DMA controller reads the display data from an external memory through a AHB master interface. The LCD controller core formats the display data. The LCD controller core continuously pumps the pixel data into the LCD module via the LCD data bus (LCDD[23:0]); this bus is timed by the LCDDOTCK, LCDDEN, LCDHSYNC, and LCDVSYNC signals. 47.6.1 DMA Controller 47.6.1.1 Configuration Block The configuration block is a set of programmable registers that are used to configure the DMA controller operation. These registers are written via the AHB slave interface. Only word access is allowed. For details on the configuration registers, see “LCD Controller (LCDC) User Interface” on page 1174. 47.6.1.2 AHB Interface This block generates the AHB transactions. It generates undefined-length incrementing bursts as well as 4-, 8- or 16-beat incrementing bursts. The size of the transfer can be configured in the BRSTLN field of the DMAFRMCFG register. For details on this register, see “DMA Frame Configuration Register” on page 1182. 47.6.1.3 Channel-U This block stores the base address and the number of words transferred for this channel (frame in single scan mode and Upper Panel in dual scan mode) since the beginning of the frame. It also generates the end of frame signal. It has two pointers, the base address and the number of words to transfer. When the module receives a new_frame signal, it reloads the number of words to transfer pointer with the size of the frame/panel. When the module receives the new_frame signal, it also reloads the base address with the base address programmed by the host. The size of the frame/panel can be programmed in the FRMSIZE field of the DMAFRMCFG Register. This size is calculated as follows: X_size*Y_size Frame_size = ------------------------------------ 32 where: X_size = ((LINESIZE+1)*Bpp+PIXELOFF)/32 Y_size = (LINEVAL+1)  LINESIZE is the horizontal size of the display in pixels, minus 1, as programmed in the LINESIZE field of the LCDFRMCFG register of the LCD Controller.  Bpp is the number of bits per pixel configured.  PIXELOFF is the pixel offset for 2D addressing, as programmed in the DMA2DCFG register. Applicable only if 2D addressing is being used. SAM9M11 [DATASHEET] 1151 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

 LINEVAL is the vertical size of the display in pixels, minus 1, as programmed in the LINEVAL field of the LCDFRMCFG register of the LCD Controller. Note: X_size is calculated as an up-rounding of a division by 32. (This can also be done adding 31 to the dividend before using an integer division by 32). When using the 2D-addressing mode (see “2D Memory Addressing” on page 1172), it is important to note that the above calculation must be executed and the FRMSIZE field programmed with every movement of the displaying window, since a change in the PIXELOFF field can change the resulting FRMSIZE value. 47.6.1.4 Channel-L This block has the same functionality as Channel-U, but for the Lower Panel in dual scan mode only. 47.6.1.5 Control This block receives the request signals from the LCDC core and generates the requests for the channels. 47.6.2 LCD Controller Core 47.6.2.1 Configuration Block The configuration block is a set of programmable registers that are used to configure the LCDC core operation. These registers are written via the AHB slave interface. Only word access is allowed. The description of the configuration registers can be found in “LCD Controller (LCDC) User Interface” on page 1174. 47.6.2.2 Datapath The datapath block contains five submodules: FIFO, Serializer, Palette, Dithering and Shifter. The structure of the datapath is shown in Figure 47-2. 1152 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 47-2. Datapath Structure Input Interface FIFO Serializer Configuration IF Palette Control Interface Dithering Output Shifter Output Interface This module transforms the data read from the memory into a format according to the LCD module used. It has four different interfaces: the input interface, the output interface, the configuration interface and the control interface.  The input interface connects the datapath with the DMA controller. It is a dual FIFO interface with a data bus and two push lines that are used by the DMA controller to fill the FIFOs.  The output interface is a 24-bit data bus. The configuration of this interface depends on the type of LCD used (TFT or STN, Single or Dual Scan, 4-bit, 8-bit, 16-bit or 24-bit interface).  The configuration interface connects the datapath with the configuration block. It is used to select between the different datapath configurations.  The control interface connects the datapath with the timing generation block. The main control signal is the data-request signal, used by the timing generation module to request new data from the datapath. The datapath can be characterized by two parameters: initial_latency and cycles_per_data. The parameter initial_latency is defined as the number of LCDC Core Clock cycles until the first data is available at the output of the datapath. The parameter cycles_per_data is the minimum number of LCDC Core clock cycles between two consecutive data at the output interface. SAM9M11 [DATASHEET] 1153 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

These parameters are different for the different configurations of the LCD Controller and are shown in Table 47-4. Table 47-4. Datapath Parameters Configuration DISTYPE SCAN IFWIDTH initial_latency cycles_per_data TFT 9 1 STN Mono Single 4 13 4 STN Mono Single 8 17 8 STN Mono Dual 8 17 8 STN Mono Dual 16 25 16 STN Color Single 4 11 2 STN Color Single 8 12 3 STN Color Dual 8 14 4 STN Color Dual 16 15 6 47.6.2.3 FIFO The FIFO block buffers the input data read by the DMA module. It contains two input FIFOs to be used in Dual Scan configuration that are configured as a single FIFO when used in single scan configuration. The size of the FIFOs allows a wide range of architectures to be supported. The upper threshold of the FIFOs can be configured in the FIFOTH field of the LCDFIFO register. The LCDC core will request a DMA transfer when the number of words in each FIFO is less than FIFOTH words. To avoid overwriting in the FIFO and to maximize the FIFO utilization, the FIFOTH should be programmed with: FIFOTH (in Words) = 512 - (2 x DMA_BURST_LENGTH + 3) where:  512 is the effective size of the FIFO in Words. It is the total FIFO memory size in single scan mode and half that size in dual scan mode.  DMA_burst_length is the burst length of the transfers made by the DMA in Words. 47.6.2.4 Serializer This block serializes the data read from memory. It reads words from the FIFO and outputs pixels (1 bit, 2 bits, 4 bits, 8 bits, 16 bits or 24 bits wide) depending on the format specified in the PIXELSIZE field of the LCDCON2 register. It also adapts the memory-ordering format. Both big-endian and little-endian formats are supported. They are configured in the MEMOR field of the LCDCON2 register. The organization of the pixel data in the memory depends on the configuration and is shown in Table 47-5 and Table 47-6. Note: For a color depth of 24 bits per pixel there are two different formats supported: packed and unpacked. The packed format needs less memory but has some limitations when working in 2D addressing mode (See “2D Memory Addressing” on page 1172.). 1154 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 47-5. Little Endian Memory Organization Mem Addr 0x3 0x2 0x1 0x0 Bit 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Pixel 1bpp 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Pixel 2bpp 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Pixel 4bpp 7 6 5 4 3 2 1 0 Pixel 8bpp 3 2 1 0 Pixel 1 0 16bpp Pixel 24bpp 1 0 packed Pixel 24bpp 2 1 packed Pixel 24bpp 3 2 packed Pixel 24bpp not used 0 unpacked Table 47-6. Big Endian Memory Organization Mem Addr 0x3 0x2 0x1 0x0 Bit 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Pixel 1bpp 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Pixel 2bpp 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Pixel 4bpp 0 1 2 3 4 5 6 7 Pixel 8bpp 0 1 2 3 Pixel 0 1 16bpp Pixel 24bpp 0 1 packed Pixel 24bpp 1 2 packed Pixel 24bpp 2 3 packed Pixel 24bpp 4 5 packed Pixel 24bpp not used 0 unpacked SAM9M11 [DATASHEET] 1155 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 47-7. WinCE Pixel Memory Organization Mem Addr 0x3 0x2 0x1 0x0 Bit 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Pixel 1bpp 24 25 26 27 28 29 30 31 16 17 18 19 20 21 22 23 8 9 10 11 12 13 14 15 0 1 2 3 4 5 6 7 Pixel 2bpp 12 13 14 15 8 9 10 11 4 5 6 7 0 1 3 3 Pixel 4bpp 6 7 4 5 2 3 0 1 Pixel 8bpp 3 2 1 0 Pixel 1 0 16bpp Pixel 24bpp 1 0 packed Pixel 24bpp 2 1 packed Pixel 24bpp 3 2 packed Pixel 24bpp not used 0 unpacked 47.6.2.5 Palette This block is used to generate the pixel gray or color information in palettized configurations. The different modes with the palettized/non-palettized configuration can be found in Table 47-8. In these modes, 1, 2, 4 or 8 input bits index an entry in the lookup table. The corresponding entry in the lookup table contains the color or gray shade information for the pixel. Table 47-8. Palette Configurations Configuration DISTYPE PIXELSIZE Palette TFT 1, 2, 4, 8 Palettized TFT 16, 24 Non-palettized STN Mono 1, 2 Palettized STN Mono 4 Non-palettized STN Color 1, 2, 4, 8 Palettized STN Color 16 Non-palettized The lookup table can be accessed by the host in R/W mode to allow the host to program and check the values stored in the palette. It is mapped in the LCD controller configuration memory map. The LUT is mapped as 16-bit half-words aligned at word boundaries, only word write access is allowed (the 16 MSB of the bus are not used). For the detailed memory map, see Table 47-15 on page 1174. The lookup table contains 256 16-bit wide entries. The 256 entries are chosen by the programmer from the 216 possible combinations. 1156 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

For the structure of each LUT entry, see Table 47-9. Table 47-9. Lookup Table Structure in the Memory Address Data Output [15:0] 00 Red_value_0[4:0] Green_value_0[5:0] Blue_value_0[4:0] 01 Red_value_1[4:0] Green_value_1[5:0] Blue_value_1[4:0] ... FE Red_value_254[4:0] Green_value_254[5:0] Blue_value_254[4:0] FF Red_value_255[4:0] Green_value_255[5:0] Blue_value_255[4:0] In STN Monochrome, only the four most significant bits of the red value are used (16 gray shades). In STN Color, only the four most significant bits of the blue, green and red value are used (4096 colors). In TFT mode, all the bits in the blue, green and red values are used. The LCDD unused bits are tied to 0 when TFT palettized configurations are used (LCDD[18:16], LCDD[9:8], LCDD[2:0]). 47.6.2.6 Dithering The dithering block is used to generate the shades of gray or color when the LCD Controller is used with an STN LCD Module. It uses a time-based dithering algorithm and Frame Rate Control method. The Frame Rate Control varies the duty cycle for which a given pixel is turned on, giving the display an appearance of multiple shades. In order to reduce the flicker noise caused by turning on and off adjacent pixels at the same time, a time-based dithering algorithm is used to vary the pattern of adjacent pixels every frame. This algorithm is expressed in terms of Dithering Pattern registers (DP_i) and considers not only the pixel gray level number, but also its horizontal coordinate. Table 47-10 shows the correspondences between the gray levels and the duty cycle. Table 47-10. Dithering Duty Cycle Gray Level Duty Cycle Pattern Register 15 1 – 14 6/7 DP6_7 13 4/5 DP4_5 12 3/4 DP3_4 11 5/7 DP5_7 10 2/3 DP2_3 9 3/5 DP3_5 8 4/7 DP4_7 7 1/2 ~DP1_2 6 3/7 ~DP4_7 5 2/5 ~DP3_5 4 1/3 ~DP2_3 3 1/4 ~DP3_4 2 1/5 ~DP4_5 1 1/7 ~DP6_7 0 0 – SAM9M11 [DATASHEET] 1157 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The duty cycles for gray levels 0 and 15 are 0 and 1, respectively. The same DP_i register can be used for the pairs for which the sum of duty cycles is 1 (e.g., 1/7 and 6/7). The dithering pattern for the first pair member is the inversion of the one for the second. The DP_i registers contain a series of 4-bit patterns. The (3-m)th bit of the pattern determines if a pixel with horizontal coordinate x = 4n + m (n is an integer and m ranges from 0 to 3) should be turned on or off in the current frame. The operation is shown by the examples below. Consider the pixels a, b, c and d with the horizontal coordinates 4*n+0, 4*n+1, 4*n+2 and 4*n+3, respectively. The four pixels should be displayed in gray level 9 (duty cycle 3/5) so the register used is DP3_5 =”1010 0101 1010 0101 1111”. The output sequence obtained in the data output for monochrome mode is shown in Table 47-11. Table 47-11. Dithering Algorithm for Monochrome Mode Frame Number Pattern Pixel a Pixel b Pixel c Pixel d N 1010 ON OFF ON OFF N+1 0101 OFF ON OFF ON N+2 1010 ON OFF ON OFF N+3 0101 OFF ON OFF ON N+4 1111 ON ON ON ON N+5 1010 ON OFF ON OFF N+6 0101 OFF ON OFF ON N+7 1010 ON OFF ON OFF ... ... ... ... ... ... Consider now color display mode and two pixels p0 and p1 with the horizontal coordinates 4*n+0, and 4*n+1. A color pixel is composed of three components: {R, G, B}. Pixel p0 will be displayed sending the color components {R0, G0, B0} to the display. Pixel p1 will be displayed sending the color components {R1, G1, B1}. Suppose that the data read from memory and mapped to the lookup tables corresponds to shade level 10 for the three color components of both pixels, with the dithering pattern to apply to all of them being DP2_3 = “1101 1011 0110”. Table 47-12 shows the output sequence in the data output bus for single scan configurations. (In Dual Scan Configuration, each panel data bus acts like in the equivalent single scan configuration.) Table 47-12. Dithering Algorithm for Color Mode Frame Signal Shadow Level Bit used Dithering Pattern 4-bit LCDD 8-bit LCDD Output N red_data_0 1010 3 1101 LCDD[3] LCDD[7] R0 N green_data_0 1010 2 1101 LCDD[2] LCDD[6] G0 N blue_data_0 1010 1 1101 LCDD[1] LCDD[5] b0 N red_data_1 1010 0 1101 LCDD[0] LCDD[4] R1 N green_data_1 1010 3 1101 LCDD[3] LCDD[3] G1 N blue_data_1 1010 2 1101 LCDD[2] LCDD[2] B1 … … … … … … … … N+1 red_data_0 1010 3 1011 LCDD[3] LCDD[7] R0 N+1 green_data_0 1010 2 1011 LCDD[2] LCDD[6] g0 N+1 blue_data_0 1010 1 1011 LCDD[1] LCDD[5] B0 1158 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 47-12. Dithering Algorithm for Color Mode (Continued) Frame Signal Shadow Level Bit used Dithering Pattern 4-bit LCDD 8-bit LCDD Output N+1 red_data_1 1010 0 1011 LCDD[0] LCDD[4] R1 N+1 green_data_1 1010 3 1011 LCDD[3] LCDD[3] G1 N+1 blue_data_1 1010 2 1011 LCDD[2] LCDD[2] b1 … … … … … … … … N+2 red_data_0 1010 3 0110 LCDD[3] LCDD[7] r0 N+2 green_data_0 1010 2 0110 LCDD[2] LCDD[6] G0 N+2 blue_data_0 1010 1 0110 LCDD[1] LCDD[5] B0 N+2 red_data_1 1010 0 0110 LCDD[0] LCDD[4] r1 N+2 green_data_1 1010 3 0110 LCDD[3] LCDD[3] g1 N+2 blue_data_1 1010 2 0110 LCDD[2] LCDD[2] B1 … … … … … … … … Note: Ri = red pixel component ON. Gi = green pixel component ON. Bi = blue pixel component ON. ri = red pixel component OFF. gi = green pixel component OFF. bi = blue pixel component OFF. 47.6.2.7 Shifter The FIFO, Serializer, Palette and Dithering modules process one pixel at a time in monochrome mode and three sub-pixels at a time in color mode (R,G,B components). This module packs the data according to the output interface. This interface can be programmed in the DISTYPE, SCANMOD, and IFWIDTH fields of the LDCCON3 register. The DISTYPE field selects between TFT, STN monochrome and STN color display. The SCANMODE field selects between single and dual scan modes; in TFT mode, only single scan is supported. The IFWIDTH field configures the width of the interface in STN mode: 4-bit (in single scan mode only), 8-bit and 16-bit (in dual scan mode only). For a more detailed description of the fields, see “LCD Controller (LCDC) User Interface” on page 1174. For a more detailed description of the LCD Interface, see “LCD Interface” on page 1164. 47.6.2.8 Time Generator The time generator block generates the control signals LCDDOTCK, LCDHSYNC, LCDVSYNC, LCDDEN, and LCDMOD, used by the LCD module. This block is programmable in order to support different types of LCD modules and obtain the output clock signals, which are derived from the LCDC Core clock. The LCDMOD signal provides an AC signal for the display. It is used by the LCD to alternate the polarity of the row and column voltages used to turn the pixels on and off. This prevents the liquid crystal from degradation. It can be configured to toggle every frame (bit MMODE = 0 in LCDMVAL register) or to toggle every programmable number of LCDHSYNC pulses (bit MMODE = 1, number of pulses defined in MVAL field of LCDMVAL register). f f = --------L---C---D----_--H----S--Y----N---C-------- LCD_MOD 2×(MVAL+1) Figure 47-3 and Figure 47-4 show the timing of LCDMOD in both configurations. SAM9M11 [DATASHEET] 1159 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 47-3. Full Frame Timing, MMODE = 1, MVAL = 1 LCDVSYNC LCDMOD LCDDOTCK Line1 Line2 Line3 Line4 Line5 Figure 47-4. Full Frame Timing, MMODE = 0 LCDVSYNC LCDMOD LCDDOTCK Line1 Line2 Line3 Line4 Line5 The LCDDOTCK signal is used to clock the data into the LCD drivers' shift register. The data is sent through LCDD[23:0] synchronized by default with LCDDOTCK falling edge (rising edge can be selected). The CLKVAL field of LCDCON1 register controls the rate of this signal. The divisor can also be bypassed with the BYPASS bit in the LCDCON1 register. In this case, the rate of LCDDOTCK is equal to the frequency of the LCDC Core clock. The minimum period of the LCDDOTCK signal depends on the configuration. This information can be found in Table 47-13. f f = ------L---C---D---C---_---c--l-o---c--k---- LCDDOTCK CLKVAL+1 The LCDDOTCK signal has two different timings that are selected with the CLKMOD field of the LCDCON2 register:  Always Active (used with TFT LCD Modules)  Active only when data is available (used with STN LCD Modules) Table 47-13. Minimum LCDDOTCK Period in LCDC Core Clock Cycles Configuration DISTYPE SCAN IFWIDTH LCDDOTCK Period TFT 1 STN Mono Single 4 4 STN Mono Single 8 8 STN Mono Dual 8 8 STN Mono Dual 16 16 STN Color Single 4 2 STN Color Single 8 2 STN Color Dual 8 4 STN Color Dual 16 6 1160 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The LCDDEN signal indicates valid data in the LCD Interface. After each horizontal line of data has been shifted into the LCD, the LCDHSYNC is asserted to cause the line to be displayed on the panel. The following timing parameters can be configured:  Vertical to Horizontal Delay (VHDLY): The delay between the falling edge of LCDVSYNC and the generation of LCDHSYNC is configurable in the VHDLY field of the LCDTIM1 register. The delay is equal to (VHDLY+1) LCDDOTCK cycles.  Horizontal Pulse Width (HPW): The LCDHSYNC pulse width is configurable in HPW field of LCDTIM2 register. The width is equal to (HPW + 1) LCDDOTCK cycles.  Horizontal Back Porch (HBP): The delay between the LCDHSYNC falling edge and the first LCDDOTCK rising edge with valid data at the LCD Interface is configurable in the HBP field of the LCDTIM2 register. The delay is equal to (HBP+1) LCDDOTCK cycles.  Horizontal Front Porch (HFP): The delay between end of valid data and the generation of the next LCDHSYNC is configurable in the HFP field of the LCDTIM2 register. The delay is equal to (HFP+VHDLY+2) LCDDOTCK cycles. There is a limitation in the minimum values of VHDLY, HPW and HBP parameters imposed by the initial latency of the datapath. The total delay in LCDC clock cycles must be higher than or equal to the latency column in Table 47- 4 on page 1154. This limitation is given by the following formula: Equation 1 (VHDLY+HPW+HBP+3)×PCLK_PERIOD≥DPATH_LATENCY where:  VHDLY, HPW, HBP are the value of the fields of LCDTIM1 and LCDTIM2 registers  PCLK_PERIOD is the period of LCDDOTCK signal measured in LCDC Clock cycles  DPATH_LATENCY is the datapath latency of the configuration, given in Table 47-4 on page 1154 The LCDVSYNC is asserted once per frame. This signal is asserted to cause the LCD's line pointer to start over at the top of the display. The timing of this signal depends on the type of LCD: STN or TFT LCD. In STN mode, the high phase corresponds to the complete first line of the frame. In STN mode, this signal is synchronized with the first active LCDDOTCK rising edge in a line. In TFT mode, the high phase of this signal starts at the beginning of the first line. The following timing parameters can be selected:  Vertical Pulse Width (VPW): LCDVSYNC pulse width is configurable in VPW field of the LCDTIM1 register. The pulse width is equal to (VPW+1) lines.  Vertical Back Porch: Number of inactive lines at the beginning of the frame is configurable in VBP field of LCDTIM1 register. The number of inactive lines is equal to VBP. This field should be programmed with 0 in STN Mode.  Vertical Front Porch: Number of inactive lines at the end of the frame is configurable in VFP field of LCDTIM2 register. The number of inactive lines is equal to VFP. This field should be programmed with 0 in STN mode. There are two other parameters to configure in this module, the HOZVAL and the LINEVAL fields of the LCDFRMCFG:  HOZVAL configures the number of active LCDDOTCK cycles in each line. The number of active cycles in each line is equal to (HOZVAL+1) cycles. The minimum value of this parameter is 1.  LINEVAL configures the number of active lines per frame. This number is equal to (LINEVAL+1) lines. The minimum value of this parameter is 1. SAM9M11 [DATASHEET] 1161 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 47-5, Figure 47-6 and Figure 47-7 show the timing of LCDDOTCK, LCDDEN, LCDHSYNC and LCDVSYNC signals: Figure 47-5. STN Panel Timing, CLKMOD 0 Frame Period LCDVSYNC LCDHSYNC LCDDEN LCDDOTCK LCDD Line Period VHDLY+ HPW+1 HBP+1 HOZVAL+1 HFP+VHDLY+2 LCDVSYNC LCDHSYNC LCDDEN LCDDOTCK LCDD 1 PCLK 1/2 PCLK 1/2 PCLK Figure 47-6. TFT Panel Timing, CLKMOD = 0, VPW = 2, VBP = 2, VFP = 1 Frame Perio d (VPW+1) Lines LCDVSYNC Vertical Back Porch = VBP Lines Vertical Front Porch = VFP Lines VHDLY+1 LCDHSYNC LCDDEN LCDDOTCK LCDD Line Period VHDLY+1 HPW+1 HBP+1 HOZVAL+1 HFP+VHDLY+2 LCDVSYNC LCDHSYNC LCDDEN LCDDOTCK LCDD 1 PCLK 1/2 PCLK 1/2 PCLK 1162 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 47-7. TFT Panel Timing (Line Expanded View), CLKMOD = 1 Line Period VHDLY+1 HPW+1 HBP+1 HOZVAL+1 HFP+VHDLY+2 LCDVSYNC LCDHSYNC LCDDEN LCDDOTCK LCDD 1PCLK 1/2 PCLK 1/2 PCLK Usually the LCD_FRM rate is about 70 Hz to 75 Hz. It is given by the following equation: -------------1--------------- = V-----H----D-----L---Y------+-----H----P----W-------+-----H----B----P-----+-----H----O----Z----V----A-----L-----+-----H----F---P-----+-----(--4----)-(VBP+LINEVAL+VFP+1) f  f  LCDVSYNC LCDDOTCK where:  HOZVAL determines de number of LCDDOTCK cycles per line  LINEVAL determines the number of LCDHSYNC cycles per frame, according to the expressions shown below: In STN Mode: Horizontal_display_size HOZVAL = ----------------------------------------------------------–1 Number_data_lines LINEVAL = Vertical_display_size–1 In monochrome mode, Horizontal_display_size is equal to the number of horizontal pixels. The number_data_lines is equal to the number of bits of the interface in single scan mode; number_data_lines is equal to half the bits of the interface in dual scan mode. In color mode, Horizontal_display_size equals three times the number of horizontal pixels. In TFT Mode: HOZVAL = Horizontal_display_size–1 LINEVAL = Vertical_display_size–1 The frame rate equation is used first without considering the clock periods added at the end beginning or at the end of each line to determine, approximately, the LCDDOTCK rate: f = (HOZVAL+5)×(f ×(LINEVAL+1)) lcd_pclk lcd_vsync With this value, the CLKVAL is fixed, as well as the corresponding LCDDOTCK rate. Then select VHDLY, HPW and HBP according to the type of LCD used and “Equation 1” on page 1161. Finally, the frame rate is adjusted to 70–75 Hz with the HFP value: 1 HFP = f × -------------------------------------------------------------------------------------------------------------- –(VHDLY+HPW+HPB+HOZVAL+4) LCDDOTCK f ×(LINEVAL+VBP+VFP+1) LCDVSYNC The line counting is controlled by the read-only field LINECNT of LCDCON1 register. The LINECNT field decreases by one unit at each falling edge of LCDHSYNC. SAM9M11 [DATASHEET] 1163 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.6.2.9 Display This block is used to configure the polarity of the data and control signals. The polarity of all clock signals can be configured by LCDCON2[12:8] register setting. This block also generates the lcd_pwr signal internally used to control the state of the LCD pins and to turn on and off by software the LCD module. It is also available on the LCDPWR pin. This signal is controlled by the PWRCON register and respects the number of frames configured in the GUARD_TIME field of PWRCON register (PWRCON[7:1]) between the write access to LCD_PWR field (PWRCON[0]) and the activation/deactivation of lcd_pwr signal. The minimum value for the GUARD_TIME field is one frame. This gives the DMA Controller enough time to fill the FIFOs before the start of data transfer to the LCD. 47.6.2.10 PWM This block generates the LCD contrast control signal (LCDCC) to make possible the control of the display's contrast by software. This is an 8-bit PWM (Pulse Width Modulation) signal that can be converted to an analog voltage with a simple passive filter. The PWM module has a free-running counter whose value is compared against a compare register (CONSTRAST_VAL register). If the value in the counter is less than that in the register, the output brings the value of the polarity (POL) bit in the PWM control register: CONTRAST_CTR. Otherwise, the opposite value is output. Thus, a periodic waveform with a pulse width proportional to the value in the compare register is generated. Due to the comparison mechanism, the output pulse has a width between zero and 255 PWM counter cycles. Thus by adding a simple passive filter outside the chip, an analog voltage between 0 and (255/256) × VDD can be obtained (for the positive polarity case, or between (1/256) × VDD and VDD for the negative polarity case). Other voltage values can be obtained by adding active external circuitry. For PWM mode, the frequency of the counter can be adjusted to four different values using field PS of CONTRAST_CTR. 47.6.3 LCD Interface The LCD Controller interfaces with the LCD Module through the LCD Interface (Table 47-14 on page 1169). The Controller supports the following interface configurations: 24-bit TFT single scan, 16-bit STN Dual Scan Mono (Color), 8-bit STN Dual (Single) Scan Mono (Color), 4-bit single scan Mono (Color). A 4-bit single scan STN display uses 4 parallel data lines to shift data to successive single horizontal lines one at a time until the entire frame has been shifted and transferred. The 4 LSB pins of LCD Data Bus (LCDD [3:0]) can be directly connected to the LCD driver; the 20 MSB pins (LCDD [23:4]) are not used. An 8-bit single scan STN display uses 8 parallel data lines to shift data to successive single horizontal lines one at a time until the entire frame has been shifted and transferred. The 8 LSB pins of LCD Data Bus (LCDD [7:0]) can be directly connected to the LCD driver; the 16 MSB pins (LCDD [23:8]) are not used. An 8-bit Dual Scan STN display uses two sets of 4 parallel data lines to shift data to successive upper and lower panel horizontal lines one at a time until the entire frame has been shifted and transferred. The bus LCDD[3:0] is connected to the upper panel data lines and the bus LCDD[7:4] is connected to the lower panel data lines. The rest of the LCD Data Bus lines (LCDD[23:8]) are not used. A 16-bit Dual Scan STN display uses two sets of 8 parallel data lines to shift data to successive upper and lower panel horizontal lines one at a time until the entire frame has been shifted and transferred. The bus LCDD[7:0] is connected to the upper panel data lines and the bus LCDD[15:8] is connected to the lower panel data lines. The rest of the LCD Data Bus lines (LCDD[23:16]) are not used. STN Mono displays require one bit of image data per pixel. STN Color displays require three bits (Red, Green and Blue) of image data per pixel, resulting in a horizontal shift register of length three times the number of pixels per 1164 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

horizontal line. This RGB or Monochrome data is shifted to the LCD driver as consecutive bits via the parallel data lines. A TFT single scan display uses up to 24 parallel data lines to shift data to successive horizontal lines one at a time until the entire frame has been shifted and transferred. The 24 data lines are divided in three bytes that define the color shade of each color component of each pixel. The LCDD bus is split as LCDD[23:16] for the blue component, LCDD[15:8] for the green component and LCDD[7:0] for the red component. If the LCD Module has lower color resolution (fewer bits per color component), only the most significant bits of each component are used. All these interfaces are shown in Figure 47-8 to Figure 47-12. Figure 47-8 shows the 24-bit single scan TFT display timing. Figure 47-9 shows the 4-bit single scan STN display timing for monochrome and color modes. Figure 47-10 on page 1166 shows the 8-bit single scan STN display timing for monochrome and color modes. Figure 47-11 on page 1167 shows the 8-bit Dual Scan STN display timing for monochrome and color modes. Figure 47-12 on page 1168 shows the 16-bit Dual Scan STN display timing for monochrome and color modes. Figure 47-8. TFT Timing (First Line Expanded View) LCDVSYNC LCDDEN LCDHSYNC LCDDOTCK LCDD [24:16] B0 B1 LCDD [15:8] G0 G1 LCDD [7:0] R0 R1 Figure 47-9. Single Scan Monochrome and Color 4-bit Panel Timing (First Line Expanded View) LCDVSYNC LCDDEN LCDHSYNC LCDDOTCK LCDD [3] P0 P4 LCDD [2] P1 P5 LCDD [1] P2 P6 LCDD [0] P3 P7 LCDVSYNC LCDDEN LCDHSYNC LCDDOTCK LCDD [3] R0 G1 LCDD [2] G0 B1 LCDD [1] B0 R2 LCDD [0] R1 G2 SAM9M11 [DATASHEET] 1165 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 47-10. Single Scan Monochrome and Color 8-bit Panel Timing (First Line Expanded View) LCDVSYNC LCDDEN LCDHSYNC LCDDOTCK LCDD [7] P0 P8 LCDD [6] P1 P9 LCDD [5] P2 P10 LCDD [4] P3 P11 LCDD [3] P4 P12 LCDD [2] P5 P13 LCDD [1] P6 P14 LCDD [0] P7 P15 LCDVSYNC LCDDEN LCDHSYNC LCDDOTCK LCDD [7] R0 B2 LCDD [6] G0 R3 LCDD [5] B0 G3 LCDD [4] R1 B3 LCDD [3] G1 R4 LCDD [2] B1 G4 LCDD [1] R2 B4 LCDD [0] G2 R5 1166 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 47-11. Dual Scan Monochrome and Color 8-bit Panel Timing (First Line Expanded View) LCDVSYNC LCDDEN LCDHSYNC LCDDOTCK Lower Pane LCDD [7] LP0 LP4 LCDD [6] LP1 LP5 LCDD [5] L2 LP6 LCDD [4] L3 LP7 Upper Pane LCDD [3] UP0 UP4 LCDD [2] UP1 UP5 LCDD [1] UP2 UP6 LCDD [0] UP3 UP7 LCDVSYNC LCDDEN LCDHSYNC LCDDOTCK Lower Pane LCDD [7] LR0 LG1 LCDD [6] LG0 LB1 LCDD [5] LB0 LR2 LCDD [4] LR1 LG2 Upper Pane LCDD [3] UR0 UG1 LCDD [2] UG0 UB1 LCDD [1] UB0 UR2 LCDD [0] UR1 UG2 SAM9M11 [DATASHEET] 1167 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 47-12. Dual Scan Monochrome and Color 16-bit Panel Timing (First Line Expanded View) LCDVSYNC LCDDEN LCDHSYNC LCDDOTCK Lower Pane l LCDD [15] LP0 LP8 LCDD [14] LP1 LP9 LCDD [13] LP2 LP10 LCDD [12] LP3 LP11 LCDD [11] LP4 LP12 LCDD [10] LP5 LP13 LCDD [9] LP6 LP14 LCDD [8] LP7 LP15 Upper Pane l LCDD [7] UP0 UP8 LCDD [6] UP1 UP9 LCDD [5] UP2 UP10 LCDD [4] UP3 UP11 LCDD [3] UP4 UP12 LCDD [2] UP5 UP13 LCDD [1] UP6 UP14 LCDD [0] UP7 UP15 LCDVSYNC LCDDEN LCDHSYNC LCDDOTCK Lower Pane l LCDD [15] LR0 LB2 LCDD [14] LG0 LR3 LCDD [13] LB0 LG3 LCDD [12] LR1 LB3 LCDD [11] LG1 LR4 LCDD [10] LB1 LG4 LCDD [9] LR2 LB4 LCDD [8] LG2 LR5 Upper Pane l LCDD [7] UR0 UB2 LCDD [6] UG0 UR3 LCDD [5] UB0 UG3 LCDD [4] UR1 UB3 LCDD [3] UG1 UR4 LCDD [2] UB1 UG4 LCDD [1] UR2 UB4 LCDD [0] UG2 UR5 1168 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 47-14. LCD Signal Multiplexing 4-bit STN Single 8-bit STN Single 8-bit STN Dual 16-bit STN Dual LCD Data Scan Scan Scan Scan Bus (mono, color) (mono, color) (mono, color) (mono, color) 24-bit TFT 16-bit TFT LCDD[23] LCD_BLUE7 LCD_BLUE4 LCDD[22] LCD_BLUE6 LCD_BLUE3 LCDD[21] LCD_BLUE5 LCD_BLUE2 LCDD[20] LCD_BLUE4 LCD_BLUE1 LCDD[19] LCD_BLUE3 LCD_BLUE0 LCDD[18] LCD_BLUE2 LCDD[17] LCD_BLUE1 LCDD[16] LCD_BLUE0 LCDD[15] LCDLP7 LCD_GREEN7 LCD_GREEN5 LCDD[14] LCDLP6 LCD_GREEN6 LCD_GREEN4 LCDD[13] LCDLP5 LCD_GREEN5 LCD_GREEN3 LCDD[12] LCDLP4 LCD_GREEN4 LCD_GREEN2 LCDD[11] LCDLP3 LCD_GREEN3 LCD_GREEN1 LCDD[10] LCDLP2 LCD_GREEN2 LCD_GREEN0 LCDD[9] LCDLP1 LCD_GREEN1 LCDD[8] LCDLP0 LCD_GREEN0 LCDD[7] LCD7 LCDLP3 LCDUP7 LCD_RED7 LCD_RED4 LCDD[6] LCD6 LCDLP2 LCDUP6 LCD_RED6 LCD_RED3 LCDD[5] LCD5 LCDLP1 LCDUP5 LCD_RED5 LCD_RED2 LCDD[4] LCD4 LCDLP0 LCDUP4 LCD_RED4 LCD_RED1 LCDD[3] LCD3 LCD3 LCDUP3 LCDUP3 LCD_RED3 LCD_RED0 LCDD[2] LCD2 LCD2 LCDUP2 LCDUP2 LCD_RED2 LCDD[1] LCD1 LCD1 LCDUP1 LCDUP1 LCD_RED1 LCDD[0] LCD0 LCD0 LCDUP0 LCDUP0 LCD_RED0 SAM9M11 [DATASHEET] 1169 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.7 Interrupts The LCD Controller generates six different IRQs. All the IRQs are synchronized with the internal LCD Core Clock. The IRQs are:  DMA Memory error IRQ. Generated when the DMA receives an error response from an AHB slave while it is doing a data transfer.  FIFO underflow IRQ. Generated when the Serializer tries to read a word from the FIFO when the FIFO is empty.  FIFO overwrite IRQ. Generated when the DMA Controller tries to write a word in the FIFO while the FIFO is full.  DMA end of frame IRQ. Generated when the DMA controller updates the Frame Base Address pointers. This IRQ can be used to implement a double-buffer technique. For more information, see “Double-buffer Technique” on page 1171.  End of Line IRQ. This IRQ is generated when the LINEBLANK period of each line is reached and the DMA Controller is in inactive state.  End of Last Line IRQ. This IRQ is generated when the LINEBLANK period of the last line of the current frame is reached and the DMA Controller is in inactive state. Each IRQ can be individually enabled, disabled or cleared, in the LCD_IER (Interrupt Enable Register), LCD_IDR (Interrupt Disable Register) and LCD_ICR (Interrupt Clear Register) registers. The LCD_IMR contains the mask value for each IRQ source and the LDC_ISR contains the status of each IRQ source. A more detailed description of these registers can be found in “LCD Controller (LCDC) User Interface” on page 1174. 47.8 Configuration Sequence The DMA Controller starts to transfer image data when the LCDC Core is activated (Write to LCD_PWR field of PWRCON register). Thus, the user should configure the LCDC Core and configure and enable the DMA Controller prior to activation of the LCD Controller. In addition, the image data to be shows should be available when the LCDC Core is activated, regardless of the value programmed in the GUARD_TIME field of the PWRCON register. To disable the LCD Controller, the user should disable the LCDC Core and then disable the DMA Controller. The user should not enable LIP again until the LCDC Core is in IDLE state. This is checked by reading the LCD_BUSY bit in the PWRCON register. The initialization sequence that the user should follow to make the LCDC work is:  Create or copy the first image to show in the display buffer memory.  If a palettized mode is used, create and store a palette in the internal LCD Palette memory (See “Palette” on page 1156.  Configure the LCD Controller Core without enabling it: ̶ LCDCON1 register: Program the CLKVAL and BYPASS fields: these fields control the pixel clock divisor that is used to generate the pixel clock LCDDOTCK. The value to program depends on the LCD Core clock and on the type and size of the LCD Module used. There is a minimum value of the LCDDOTCK clock period that depends on the LCD Controller Configuration, this minimum value can be found in Table 47-13 on page 1160. The equations that are used to calculate the value of the pixel clock divisor can be found at the end of the section “Time Generator” on page 1159. ̶ LCDCON2 register: Program its fields following their descriptions in the LCD Controller User Interface section below and considering the type of LCD module used and the desired working mode. Consider that not all combinations are possible. ̶ LCDTIM1 and LCDTIM2 registers: Program their fields according to the datasheet of the LCD module used and with the help of the “Time Generator” on page 1159. Note that some fields are not applicable to STN modules and must be programmed with 0 values. Note also that there is a limitation on the minimum value of VHDLY, HPW, HBP that depends on the configuration of the LCDC. 1170 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

̶ LCDFRMCFG register: program the dimensions of the LCD module used. ̶ LCDFIFO register: To program it, use the formula in section “FIFO” on page 1154. ̶ LCDMVAL register: Its configuration depends on the LCD Module used and should be tuned to improve the image quality in the display (See “Time Generator” on page 1159.) ̶ DP1_2 to DP6_7 registers: they are only used for STN displays. They contain the dithering patterns used to generate gray shades or colors in these modules. They are loaded with recommended patterns at reset, so it is not necessary to write anything on them. They can be used to improve the image quality in the display by tuning the patterns in each application. ̶ PWRCON Register: this register controls the power-up sequence of the LCD, so take care to use it properly. Do not enable the LCD (writing a 1 in LCD_PWR field) until the previous steps and the configuration of the DMA have been finished. ̶ CONTRAST_CTR and CONTRAST_VAL: use this registers to adjust the contrast of the display, when the LCDCC line is used.  Configure the DMA Controller. The user should configure the base address of the display buffer memory, the size of the AHB transaction and the size of the display image in memory. When the DMA is configured the user should enable the DMA. To do so the user should configure the following registers: ̶ DMABADDR1 and DMABADDR2 registers: In single scan mode only DMABADDR1 register must be configured with the base address of the display buffer in memory. In dual scan mode DMABADDR1 should be configured with the base address of the Upper Panel display buffer and DMABADDR2 should be configured with the base address of the Lower Panel display buffer. ̶ DMAFRMCFG register: Program the FRMSIZE field. Note that in dual scan mode the vertical size to use in the calculation is that of each panel. Respect to the BRSTLN field, a recommended value is a 4- word burst. ̶ DMACON register: Once both the LCD Controller Core and the DMA Controller have been configured, enable the DMA Controller by writing a “1” to the DMAEN field of this register. If using a dual scan module or the 2D addressing feature, do not forget to write the DMAUPDT bit after every change to the set of DMA configuration values. ̶ DMA2DCFG register: Required only in 2D memory addressing mode (see “2D Memory Addressing” on page 1172).  Finally, enable the LCD Controller Core by writing a “1” in the LCD_PWR field of the PWRCON register and do any other action that may be required to turn the LCD module on. 47.9 Double-buffer Technique The double-buffer technique is used to avoid flickering while the frame being displayed is updated. Instead of using a single buffer, there are two different buffers, the back buffer (background buffer) and the primary buffer (the buffer being displayed). The host updates the back buffer while the LCD Controller is displaying the primary buffer. When the back buffer has been updated the host updates the DMA Base Address registers. When using a Dual Panel LCD Module, both base address pointers should be updated in the same frame. There are two possibilities:  Check the DMAFRMPTx register to ensure that there is enough time to update the DMA Base Address registers before the end of frame.  Update the Frame Base Address Registers when the End Of Frame IRQ is generated. Once the host has updated the Frame Base Address Registers and the next DMA end of frame IRQ arrives, the back buffer and the primary buffer are swapped and the host can work with the new back buffer. When using a dual-panel LCD module, both base address pointers should be updated in the same frame. In order to achieve this, the DMAUPDT bit in DMACON register must be used to validate the new base address. SAM9M11 [DATASHEET] 1171 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.10 2D Memory Addressing The LCDC can be configured to work on a frame buffer larger than the actual screen size. By changing the values in a few registers, it is easy to move the displayed area along the frame buffer width and height. Figure 47-13. Frame Buffer Addressing Frame Buffer Displayed Image Base word address & pixel offset Line-to-line address increment In order to locate the displayed window within a larger frame buffer, the software must:  Program the DMABADDR1 (DMABADDR2) register(s) to make them point to the word containing the first pixel of the area of interest.  Program the PIXELOFF field of DMA2DCFG register to specify the offset of this first pixel within the 32-bit memory word that contains it.  Define the width of the complete frame buffer by programming in the field ADDRINC of DMA2DCFG register the address increment between the last word of a line and the first word of the next line (in number of 32-bit words).  Enable the 2D addressing mode by writing the DMA2DEN bit in DMACON register. If this bit is not activated, the values in the DMA2DCFG register are not considered and the controller assumes that the displayed area occupies a continuous portion of the memory. The above configuration can be changed frame to frame, so the displayed window can be moved rapidly. Note that the FRMSIZE field of DMAFRMCFG register must be updated with any movement of the displaying window. Note also that the software must write bit DMAUPDT in DMACON register after each configuration for it to be accepted by LCDC. Note: In 24 bpp packed mode, the DMA base address must point to a word containing a complete pixel (possible values of PIXELOFF are 0 and 8). This means that the horizontal origin of the displaying window must be a multiple of 4 pixels or a multiple of 4 pixels minus 1 (x = 4n or x = 4n-1, valid origins are pixel 0,3,4,7,8,11,12, etc.). 1172 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.11 Register Configuration Guide Program the PIO Controller to enable LCD signals. Enable the LCD controller clock in the Power Management Controller. 47.11.1 STN Mode Example STN color(R,G,B) 320*240, 8-bit single scan, 70 frames/sec, Master clock = 60 MHz Data rate: 320*240*70*3/8 = 2.016 MHz HOZVAL = ((3*320)/8) - 1 LINEVAL = 240 -1 CLKVAL = (60 MHz/2.016 MHz) - 1 = 29 LCDCON1 = CLKVAL << 12 LCDCON2 = LITTLEENDIAN | SINGLESCAN | STNCOLOR | DISP8BIT| PS8BPP; LCDTIM1 = 0; LCDTIM2 = 10 | (10 << 21); LCDFRMCFG = (HOZVAL << 21) | LINEVAL; LCDMVAL = 0x80000004; DMAFRMCFG = (7 << 24) + (320 * 240 * 8) / 32; 47.11.2 TFT Mode Example This example is based on the NEC TFT color LCD module NL6448BC20-08. TFT 640*480, 16-bit single scan, 60 frames/sec, pixel clock frequency = [21 MHz..29 MHz] with a typical value = 25.175 MHz. The Master clock must be (n + 1)*pixel clock frequency HOZVAL = 640 - 1 LINEVAL = 480 - 1 If Master clock is 100 MHz CLKVAL = (100 MHz / 25.175 MHz) - 1 = 3 VFP = (12 -1), VBP = (31-1), VPW = (2-1), VHDLY = (2-1) HFP = (16-1), HBP = (48 -1), HPW = (96-1) LCDCON1 = CLKVAL << 12 LCDCON2 = LITTLEENDIAN | CLKMOD | INVERT_CLK | INVERT_LINE | INVERT_FRM | PS16BPP | SINGLESCAN | TFT LCDTIM1 = VFP | (VBP << 8) | (VPW << 16) | (VHDLY << 24) LCDTIM2 = HBP | (HPW << 8) | (HFP << 21) LCDFRMCFG = (HOZVAL << 21) | LINEVAL LCDMVAL = 0 DMAFRMCFG = (7 << 24) + (640 * 480* 16) / 32; SAM9M11 [DATASHEET] 1173 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12 LCD Controller (LCDC) User Interface Table 47-15. Register Mapping Offset Register Name Access Reset 0x0 DMA Base Address Register 1 DMABADDR1 Read/Write 0x00000000 0x4 DMA Base Address Register 2 DMABADDR2 Read/Write 0x00000000 0x8 DMA Frame Pointer Register 1 DMAFRMPT1 Read-only 0x00000000 0xC DMA Frame Pointer Register 2 DMAFRMPT2 Read-only 0x00000000 0x10 DMA Frame Address Register 1 DMAFRMADD1 Read-only 0x00000000 0x14 DMA Frame Address Register 2 DMAFRMADD2 Read-only 0x00000000 0x18 DMA Frame Configuration Register DMAFRMCFG Read/Write 0x00000000 0x1C DMA Control Register DMACON Read/Write 0x00000000 0x20 DMA Control Register DMA2DCFG Read/Write 0x00000000 0x800 LCD Control Register 1 LCDCON1 Read/Write 0x00002000 0x804 LCD Control Register 2 LCDCON2 Read/Write 0x00000000 0x808 LCD Timing Register 1 LCDTIM1 Read/Write 0x00000000 0x80C LCD Timing Register 2 LCDTIM2 Read/Write 0x00000000 0x810 LCD Frame Configuration Register LCDFRMCFG Read/Write 0x00000000 0x814 LCD FIFO Register LCDFIFO Read/Write 0x00000000 0x818 LCDMOD Toggle Rate Value Register LCDMVAL Read/Write 0x00000000 0x81C Dithering Pattern DP1_2 DP1_2 Read/Write 0xA5 0x820 Dithering Pattern DP4_7 DP4_7 Read/Write 0x5AF0FA5 0x824 Dithering Pattern DP3_5 DP3_5 Read/Write 0xA5A5F 0x828 Dithering Pattern DP2_3 DP2_3 Read/Write 0xA5F 0x82C Dithering Pattern DP5_7 DP5_7 Read/Write 0xFAF5FA5 0x830 Dithering Pattern DP3_4 DP3_4 Read/Write 0xFAF5 0x834 Dithering Pattern DP4_5 DP4_5 Read/Write 0xFAF5F 0x838 Dithering Pattern DP6_7 DP6_7 Read/Write 0xF5FFAFF 0x83C Power Control Register PWRCON Read/Write 0x0000000e 0x840 Contrast Control Register CONTRAST_CTR Read/Write 0x00000000 0x844 Contrast Value Register CONTRAST_VAL Read/Write 0x00000000 0x848 LCD Interrupt Enable Register LCD_IER Write-only – 0x84C LCD Interrupt Disable Register LCD_IDR Write-only – 0x850 LCD Interrupt Mask Register LCD_IMR Read-only 0x0 0x854 LCD Interrupt Status Register LCD_ISR Read-only 0x0 0x858 LCD Interrupt Clear Register LCD_ICR Write-only – 0x860 LCD Interrupt Test Register LCD_ITR Write-only – 0x864 LCD Interrupt Raw Status Register LCD_IRR Read-only 0 0x8E4 Write Protection Control Register LCD_WPCR Read/Write 0 1174 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 47-15. Register Mapping (Continued) Offset Register Name Access Reset 0x8E8 Write Protection Status Register LCD_WPSR Read-only 0 0xC00 Palette entry 0 LUT ENTRY 0 Read/Write 0xC04 Palette entry 1 LUT ENTRY 1 Read/Write 0xC08 Palette entry 2 LUT ENTRY 2 Read/Write 0xC0C Palette entry 3 LUT ENTRY 3 Read/Write … … 0xFFC Palette entry 255 LUT ENTRY 255 Read/Write SAM9M11 [DATASHEET] 1175 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.1 DMA Base Address Register 1 Name: DMABADDR1 Address: 0x00500000 Access: Read/Write 31 30 29 28 27 26 25 24 BADDR-U 23 22 21 20 19 18 17 16 BADDR-U 15 14 13 12 11 10 9 8 BADDR-U 7 6 5 4 3 2 1 0 BADDR-U 0 0 • BADDR-U Base Address for the upper panel in dual scan mode. Base Address for the complete frame in single scan mode. If a dual scan configuration is selected in LCDCON2 register or bit DMA2DEN in register DMACON is set, the bit DMAUPDT in that same register must be written after writing any new value to this field in order to make the DMA control- ler use this new value. 1176 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.2 DMA Base Address Register 2 Name: DMABADDR2 Address: 0x00500004 Access: Read/Write 31 30 29 28 27 26 25 24 BADDR-L 23 22 21 20 19 18 17 16 BADDR-L 15 14 13 12 11 10 9 8 BADDR-L 7 6 5 4 3 2 1 0 BADDR-L • BADDR-L Base Address for the lower panel in dual scan mode only. If a dual scan configuration is selected in LCDCON2 register or bit DMA2DEN in register DMACON is set, the bit DMAUPDT in that same register must be written after writing any new value to this field in order to make the DMA control- ler use this new value. SAM9M11 [DATASHEET] 1177 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.3 DMA Frame Pointer Register 1 Name: DMAFRMPT1 Address: 0x00500008 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – FRMPT-U 15 14 13 12 11 10 9 8 FRMPT-U 7 6 5 4 3 2 1 0 FRMPT-U • FRMPT-U Current value of frame pointer for the upper panel in dual scan mode. Current value of frame pointer for the complete frame in single scan mode. Down count from FRMSIZE to 0. Note: This register is read-only and contains the current value of the frame pointer (number of words to the end of the frame). It can be used as an estimation of the number of words transferred from memory for the current frame. 1178 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.4 DMA Frame Pointer Register 2 Name: DMAFRMPT2 Address: 0x0050000C Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 - FRMPT-L 15 14 13 12 11 10 9 8 FRMPT-L 7 6 5 4 3 2 1 0 FRMPT-L • FRMPT-L Current value of frame pointer for the Lower panel in dual scan mode only. Down count from FRMSIZE to 0. Note: This register is read-only and contains the current value of the frame pointer (number of words to the end of the frame). It can be used as an estimation of the number of words transferred from memory for the current frame. SAM9M11 [DATASHEET] 1179 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.5 DMA Frame Address Register 1 Name: DMAFRMADD1 Address: 0x00500010 Access: Read-only 31 30 29 28 27 26 25 24 FRMADD-U 23 22 21 20 19 18 17 16 FRMADD-U 15 14 13 12 11 10 9 8 FRMADD-U 7 6 5 4 3 2 1 0 FRMADD-U • FRMADD-U Current value of frame address for the upper panel in dual scan mode. Current value of frame address for the complete frame in single scan. Note: This register is read-only and contains the current value of the last DMA transaction in the bus for the panel/frame. 1180 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.6 DMA Frame Address Register 2 Name: DMAFRMADD2 Address: 0x00500014 Access: Read-only 31 30 29 28 27 26 25 24 FRMADD-L 23 22 21 20 19 18 17 16 FRMADD-L 15 14 13 12 11 10 9 8 FRMADD-L 7 6 5 4 3 2 1 0 FRMADD-L • FRMADD-L Current value of frame address for the lower panel in single scan mode only. Note: This register is read-only and contains the current value of the last DMA transaction in the bus for the panel. SAM9M11 [DATASHEET] 1181 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.7 DMA Frame Configuration Register Name: DMAFRMCFG Address: 0x00500018 Access: Read/Write 31 30 29 28 27 26 25 24 – BRSTLN 23 22 21 20 19 18 17 16 – FRMSIZE 15 14 13 12 11 10 9 8 FRMSIZE 7 6 5 4 3 2 1 0 FRMSIZE • FRMSIZE: Frame Size In single scan mode, this is the frame size in words. In dual scan mode, this is the size of each panel. If a dual scan configuration is selected in LCDCON2 register or bit DMA2DEN in register DMACON is set, the bit DMAUPDT in that same register must be written after writing any new value to this field in order to make the DMA control- ler use this new value. • BRSTLN: Burst Length in Words Program with the desired burst length - 1 1182 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.8 DMA Control Register Name: DMACON Address: 0x0050001C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – DMA2DEN DMAUPDT DMABUSY DMARST DMAEN • DMAEN: DMA Enable 0: DMA is disabled. 1: DMA is enabled. • DMARST: DMA Reset (Write-only) 0: No effect. 1: Reset DMA module. DMA Module should be reset only when disabled and in idle state. • DMABUSY: DMA Busy 0: DMA module is idle. 1: DMA module is busy (doing a transaction on the AHB bus). • DMAUPDT: DMA Configuration Update 0: No effect 1: Update DMA Configuration. Used for simultaneous updating of DMA parameters in dual scan mode or when using 2D addressing. The values written in the registers DMABADDR1, DMABADDR2 and DMA2DCFG, and in the field FRMSIZE of register DMAFRMCFG, are accepted by the DMA controller and are applied at the next frame. This bit is used only if a dual scan configuration is selected (bit SCANMOD of LCDCON2 register) or 2D addressing is enabled (bit DMA2DEN in this register). Otherwise, the LCD controller accepts immediately the values written in the registers referred to above. • DMA2DEN: DMA 2D Addressing Enable 0: 2D addressing is disabled (values in register DMA2DCFG are “don’t care”). 1: 2D addressing is enabled. SAM9M11 [DATASHEET] 1183 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.9 LCD DMA 2D Addressing Register Name: DMA2DCFG Address: 0x00500020 Access: Read/Write 31 30 29 28 27 26 25 24 – – – PIXELOFF 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 ADDRINC 7 6 5 4 3 2 1 0 ADDRINC • ADDRINC: DMA 2D Addressing Address increment When 2-D DMA addressing is enabled (bit DMA2DEN is set in register DMACON), this field specifies the number of bytes that the DMA controller must jump between screen lines. Itb must be programmed as: [({address of first 32-bit word in a screen line} - {address of last 32-bit word in previous line})]. In other words, it is equal to 4*[number of 32-bit words occu- pied by each line in the complete frame buffer minus the number of 32-bit words occupied by each displayed line]. Bit DMAUPDT in register DMACON must be written after writing any new value to this field in order to make the DMA control- ler use this new value. • PIXELOFF: DAM2D Addressing Pixel offset When 2D DMA addressing is enabled (bit DMA2DEN is set in register DMACON), this field specifies the offset of the first pixel in each line within the memory word that contains this pixel. The offset is specified in number of bits in the range 0– 31, so for example a value of 4 indicates that the first pixel in the screen starts at bit 4 of the 32-bit word pointed by register DMABADDR1. Bits 0 to 3 of that word are not used. This example is valid for little endian memory organization. When using big endian memory organization, this offset is considered from bit 31 downwards, or equivalently, a given value of this field always selects the pixel in the same relative position within the word, independently of the memory ordering con- figuration. Bit DMAUPDT in register DMACON must be written after writing any new value to this field in order to make the DMA controller use this new value. 1184 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.10 LCD Control Register 1 Name: LCDCON1 Address: 0x00500800 Access: Read/Write, except LINECNT: Read-only 31 30 29 28 27 26 25 24 LINECNT 23 22 21 20 19 18 17 16 LINECNT CLKVAL 15 14 13 12 11 10 9 8 CLKVAL – – – – 7 6 5 4 3 2 1 0 – – – – – – – BYPASS • BYPASS: Bypass LCDDOTCK Divider 0: The divider is not bypassed. LCDDOTCK frequency defined by the CLKVAL field. 1: The LCDDOTCK divider is bypassed. LCDDOTCK frequency is equal to the LCDC Clock frequency. • CLKVAL: Clock Divider 9-bit divider for pixel clock (LCDDOTCK) frequency. Pixel_clock = system_clock⁄(CLKVAL +1) • LINECNT: Line Counter (Read-only) Current Value of 11-bit line counter. Down count from LINEVAL to 0. SAM9M11 [DATASHEET] 1185 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.11 LCD Control Register 2 Name: LCDCON2 Address: 0x00500804 Access: Read/Write 31 30 29 28 27 26 25 24 MEMOR – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 CLKMOD – – INVDVAL INVCLK INVLINE INVFRAME INVVD 7 6 5 4 3 2 1 0 PIXELSIZE IFWIDTH SCANMOD DISTYPE • DISTYPE: Display Type DISTYPE 0 0 STN Monochrome 0 1 STN Color 1 0 TFT 1 1 Reserved • SCANMOD: Scan Mode 0: Single Scan 1: Dual Scan • IFWIDTH: Interface width (STN) IFWIDTH 0 0 4-bit (Only valid in single scan STN mono or color) 0 1 8-bit (Only valid in STN mono or Color) 1 0 16-bit (Only valid in dual scan STN mono or color) 1 1 Reserved • PIXELSIZE: Bits per pixel PIXELSIZE 0 0 0 1 bit per pixel 0 0 1 2 bits per pixel 0 1 0 4 bits per pixel 0 1 1 8 bits per pixel 1 0 0 16 bits per pixel 1 0 1 24 bits per pixel, packed (Only valid in TFT mode) 1 1 0 24 bits per pixel, unpacked (Only valid in TFT mode) 1 1 1 Reserved 1186 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• INVVD: LCDD polarity 0: Normal 1: Inverted • INVFRAME: LCDVSYNC polarity 0: Normal (active high) 1: Inverted (active low) • INVLINE: LCDHSYNC polarity 0: Normal (active high) 1: Inverted (active low) • INVCLK: LCDDOTCK polarity 0: Normal (LCDD fetched at LCDDOTCK falling edge) 1: Inverted (LCDD fetched at LCDDOTCK rising edge) • INVDVAL: LCDDEN polarity 0: Normal (active high) 1: Inverted (active low) • CLKMOD: LCDDOTCK mode 0: LCDDOTCK only active during active display period 1: LCDDOTCK always active • MEMOR: Memory Ordering Format 00: Big Endian 10: Little Endian 11: WinCE format SAM9M11 [DATASHEET] 1187 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.12 LCD Timing Configuration Register 1 Name: LCDTIM1 Address: 0x00500808 Access: Read/Write 31 30 29 28 27 26 25 24 1 – – – VHDLY 23 22 21 20 19 18 17 16 – – VPW 15 14 13 12 11 10 9 8 VBP 7 6 5 4 3 2 1 0 VFP • VFP: Vertical Front Porch In TFT mode, these bits equal the number of idle lines at the end of the frame. In STN mode, these bits should be set to 0. • VBP: Vertical Back Porch In TFT mode, these bits equal the number of idle lines at the beginning of the frame. In STN mode, these bits should be set to 0. • VPW: Vertical Synchronization pulse width In TFT mode, these bits equal the vertical synchronization pulse width, given in number of lines. LCDVSYNC width is equal to (VPW+1) lines. In STN mode, these bits should be set to 0. • VHDLY: Vertical to horizontal delay In TFT mode, this is the delay between LCDVSYNC rising or falling edge and LCDHSYNC rising edge. Delay is (VHDLY+1) LCDDOTCK cycles. Bit 31 must be written to 1. In STN mode, these bits should be set to 0. 1188 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.13 LCD Timing Configuration Register 2 Name: LCDTIM2 Address: 0x0050080C Access: Read/Write 31 30 29 28 27 26 25 24 HFP 23 22 21 20 19 18 17 16 HFP – – – – – 15 14 13 12 11 10 9 8 – – HPW 7 6 5 4 3 2 1 0 HBP • HBP: Horizontal Back Porch Number of idle LCDDOTCK cycles at the beginning of the line. Idle period is (HBP+1) LCDDOTCK cycles. • HPW: Horizontal synchronization pulse width Width of the LCDHSYNC pulse, given in LCDDOTCK cycles. Width is (HPW+1) LCDDOTCK cycles. • HFP: Horizontal Front Porch Number of idle LCDDOTCK cycles at the end of the line. Idle period is (HFP+1) LCDDOTCK cycles. SAM9M11 [DATASHEET] 1189 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.14 LCD Frame Configuration Register Name: LCDFRMCFG Address: 0x00500810 Access: Read/Write 31 30 29 28 27 26 25 24 LINESIZE 23 22 21 20 19 18 17 16 LINESIZE – – – – – 15 14 13 12 11 10 9 8 – – – – – LINEVAL 7 6 5 4 3 2 1 0 LINEVAL • LINEVAL: Vertical size of LCD module In single scan mode: vertical size of LCD Module, in pixels, minus 1 In dual scan mode: vertical display size of each LCD panel, in pixels, minus 1 • LINESIZE: Horizontal size of LCD module, in pixels, minus 1 1190 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.15 LCD FIFO Register Name: LCDFIFO Address: 0x00500814 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 FIFOTH 7 6 5 4 3 2 1 0 FIFOTH • FIFOTH: FIFO Threshold Must be programmed with: FIFOTH (in Words) = 512 - (2 x DMA_BURST_LENGTH + 3) where: (cid:129) 512 is the effective size of the FIFO in Words. It is the total FIFO memory size in single scan mode and half that size in dual scan mode. (cid:129) DMA_burst_length is the burst length of the transfers made by the DMA (in Words). Refer to “BRSTLN: Burst Length in Words” on page 1182. SAM9M11 [DATASHEET] 1191 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.16 LCDMOD Toggle Rate Value Register Name: LCDMVAL Access: Read/Write 31 30 29 28 27 26 25 24 MMODE – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 MVAL • MVAL: LCDMOD toggle rate value LCDMOD toggle rate if MMODE = 1. Toggle rate is MVAL + 1 line periods. • MMODE: LCDMOD toggle rate select 0: Each Frame 1: Rate defined by MVAL 1192 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.17 Dithering Pattern DP1_2 Register Name: DP1_2 Address: 0x0050081C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 DP1_2 • DP1_2: Pattern value for ½ duty cycle SAM9M11 [DATASHEET] 1193 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.18 Dithering Pattern DP4_7 Register Name: DP4_7 Address: 0x00500820 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – DP4_7 23 22 21 20 19 18 17 16 DP4_7 15 14 13 12 11 10 9 8 DP4_7 7 6 5 4 3 2 1 0 DP4_7 • DP4_7: Pattern value for 4/7 duty cycle 1194 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.19 Dithering Pattern DP3_5 Register Name: DP3_5 Address: 0x00500824 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – DP3_5 15 14 13 12 11 10 9 8 DP3_5 7 6 5 4 3 2 1 0 DP3_5 • DP3_5: Pattern value for 3/5 duty cycle SAM9M11 [DATASHEET] 1195 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.20 Dithering Pattern DP2_3 Register Name: DP2_3 Address: 0x00500828 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – DP2_3 7 6 5 4 3 2 1 0 DP2_3 • DP2_3: Pattern value for 2/3 duty cycle 1196 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.21 Dithering Pattern DP5_7 Register Name: DP5_7 Address: 0x0050082C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – DP5_7 23 22 21 20 19 18 17 16 DP5_7 15 14 13 12 11 10 9 8 DP5_7 7 6 5 4 3 2 1 0 DP5_7 • DP5_7: Pattern value for 5/7 duty cycle SAM9M11 [DATASHEET] 1197 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.22 Dithering Pattern DP3_4 Register Name: DP3_4 Address: 0x00500830 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 DP3_4 7 6 5 4 3 2 1 0 DP3_4 • DP3_4: Pattern value for 3/4 duty cycle 1198 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.23 Dithering Pattern DP4_5 Register Name: DP4_5 Address: 0x00500834 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – DP4_5 15 14 13 12 11 10 9 8 DP4_5 7 6 5 4 3 2 1 0 DP4_5 • DP4_5: Pattern value for 4/5 duty cycle SAM9M11 [DATASHEET] 1199 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.24 Dithering Pattern DP6_7 Register Name: DP6_7 Address: 0x00500838 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – DP6_7 23 22 21 20 19 18 17 16 DP6_7 15 14 13 12 11 10 9 8 DP6_7 7 6 5 4 3 2 1 0 DP6_7 • DP6_7: Pattern value for 6/7 duty cycle 1200 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.25 Power Control Register Name: PWRCON Address: 0x0050083C Access: Read/Write 31 30 29 28 27 26 25 24 LCD_BUSY – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 GUARD_TIME LCD_PWR • LCD_PWR: LCD module power control 0 = lcd_pwr signal is low, other lcd_* signals are low. 0->1 = lcd_* signals activated, lcd_pwr is set high with the delay of GUARD_TIME frame periods. 1 = lcd_pwr signal is high, other lcd_* signals are active. 1->0 = lcd_pwr signal is low, other lcd_* signals are active, but are set low after GUARD_TIME frame periods. • GUARD_TIME Delay in frame periods between applying control signals to the LCD module and setting LCD_PWR high, and between set- ting LCD_PWR low and removing control signals from LCD module • LCD_BUSY Read-only field. If 1, it indicates that the LCD is busy (active and displaying data, in power on sequence or in power off sequence). SAM9M11 [DATASHEET] 1201 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.26 Contrast Control Register Name: CONTRAST_CTR Address: 0x00500840 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – ENA POL PS • PS This 2-bit value selects the configuration of a counter prescaler. The meaning of each combination is as follows: PS 0 0 The counter advances at a rate of f = f . COUNTER LCDC_CLOCK 0 1 The counter advances at a rate of f = f /2. COUNTER LCDC_CLOCK 1 0 The counter advances at a rate of f = f /4. COUNTER LCDC_CLOCK 1 1 The counter advances at a rate of f = f /8. COUNTER LCDC_CLOCK • POL This bit defines the polarity of the output. If 1, the output pulses are high level (the output will be high whenever the value in the counter is less than the value in the compare register CONSTRAST_VAL). If 0, the output pulses are low level. • ENA When 1, this bit enables the operation of the PWM generator. When 0, the PWM counter is stopped. 1202 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.27 Contrast Value Register Name: CONSTRAST_VAL Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 CVAL • CVAL PWM compare value. Used to adjust the analog value obtained after an external filter to control the contrast of the display. SAM9M11 [DATASHEET] 1203 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.28 LCD Interrupt Enable Register Name: LCD_IER Address: 0x00500848 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – MERIE OWRIE UFLWIE - EOFIE LSTLNIE LNIE • LNIE: Line interrupt enable 0: No effect 1: Enable each line interrupt • LSTLNIE: Last line interrupt enable 0: No effect 1: Enable last line interrupt • EOFIE: DMA End of frame interrupt enable 0: No effect 1: Enable End Of Frame interrupt • UFLWIE: FIFO underflow interrupt enable 0: No effect 1: Enable FIFO underflow interrupt • OWRIE: FIFO overwrite interrupt enable 0: No effect 1: Enable FIFO overwrite interrupt • MERIE: DMA memory error interrupt enable 0: No effect 1: Enable DMA memory error interrupt 1204 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.29 LCD Interrupt Disable Register Name: LCD_IDR Address: 0x0050084C Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – MERID OWRID UFLWID – EOFID LSTLNID LNID • LNID: Line interrupt disable 0: No effect 1: Disable each line interrupt • LSTLNID: Last line interrupt disable 0: No effect 1: Disable last line interrupt • EOFID: DMA End of frame interrupt disable 0: No effect 1: Disable End Of Frame interrupt • UFLWID: FIFO underflow interrupt disable 0: No effect 1: Disable FIFO underflow interrupt • OWRID: FIFO overwrite interrupt disable 0: No effect 1: Disable FIFO overwrite interrupt • MERID: DMA Memory error interrupt disable 0: No effect 1: Disable DMA Memory error interrupt SAM9M11 [DATASHEET] 1205 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.30 LCD Interrupt Mask Register Name: LCD_IMR Address: 0x00500850 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – MERIM OWRIM UFLWIM – EOFIM LSTLNIM LNIM • LNIM: Line interrupt mask 0: Line Interrupt disabled 1: Line interrupt enabled • LSTLNIM: Last line interrupt mask 0: Last Line Interrupt disabled 1: Last Line Interrupt enabled • EOFIM: DMA End of frame interrupt mask 0: End Of Frame interrupt disabled 1: End Of Frame interrupt enabled • UFLWIM: FIFO underflow interrupt mask 0: FIFO underflow interrupt disabled 1: FIFO underflow interrupt enabled • OWRIM: FIFO overwrite interrupt mask 0: FIFO overwrite interrupt disabled 1: FIFO overwrite interrupt enabled • MERIM: DMA Memory error interrupt mask 0: DMA Memory error interrupt disabled 1: DMA Memory error interrupt enabled 1206 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.31 LCD Interrupt Status Register Name: LCD_ISR Address: 0x00500854 Access: Read-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – MERIS OWRIS UFLWIS – EOFIS LSTLNIS LNIS • LNIS: Line interrupt status 0: Line Interrupt not active 1: Line Interrupt active • LSTLNIS: Last line interrupt status 0: Last Line Interrupt not active 1: Last Line Interrupt active • EOFIS: DMA End of frame interrupt status 0: End Of Frame interrupt not active 1: End Of Frame interrupt active • UFLWIS: FIFO underflow interrupt status 0: FIFO underflow interrupt not active 1: FIFO underflow interrupt active • OWRIS: FIFO overwrite interrupt status 0: FIFO overwrite interrupt not active 1: FIFO overwrite interrupt active • MERIS: DMA Memory error interrupt status 0: DMA Memory error interrupt not active 1: DMA Memory error interrupt active SAM9M11 [DATASHEET] 1207 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.32 LCD Interrupt Clear Register Name: LCD_ICR Address: 0x00500858 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – MERIC OWRIC UFLWIC – EOFIC LSTLNIC LNIC • LNIC: Line interrupt clear 0: No effect 1: Clear each line interrupt • LSTLNIC: Last line interrupt clear 0: No effect 1: Clear Last line Interrupt • EOFIC: DMA End of frame interrupt clear 0: No effect 1: Clear End Of Frame interrupt • UFLWIC: FIFO underflow interrupt clear 0: No effect 1: Clear FIFO underflow interrupt • OWRIC: FIFO overwrite interrupt clear 0: No effect 1: Clear FIFO overwrite interrupt • MERIC: DMA Memory error interrupt clear 0: No effect 1: Clear DMA Memory error interrupt 1208 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.33 LCD Interrupt Test Register Name: LCD_ITR Address: 0x00500860 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – MERIT OWRIT UFLWIT – EOFIT LSTLNIT LNIT • LNIT: Line interrupt test 0: No effect 1: Set each line interrupt • LSTLNIT: Last line interrupt test 0: No effect 1: Set Last line interrupt • EOFIT: DMA End of frame interrupt test 0: No effect 1: Set End Of Frame interrupt • UFLWIT: FIFO underflow interrupt test 0: No effect 1: Set FIFO underflow interrupt • OWRIT: FIFO overwrite interrupt test 0: No effect 1: Set FIFO overwrite interrupt • MERIT: DMA Memory error interrupt test 0: No effect 1: Set DMA Memory error interrupt SAM9M11 [DATASHEET] 1209 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.34 LCD Interrupt Raw Status Register Name: LCD_IRR Address: 0x00500864 Access: Write-only 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – MERIR OWRIR UFLWIR – EOFIR LSTLNIR LNIR • LNIR: Line interrupt raw status 0: No effect 1: Line interrupt condition present • LSTLNIR: Last line interrupt raw status 0: No effect 1: Last line Interrupt condition present • EOFIR: DMA End of frame interrupt raw status 0: No effect 1: End Of Frame interrupt condition present • UFLWIR: FIFO underflow interrupt raw status 0: No effect 1: FIFO underflow interrupt condition present • OWRIR: FIFO overwrite interrupt raw status 0: No effect 1: FIFO overwrite interrupt condition present • MERIR: DMA Memory error interrupt raw status 0: No effect 1: DMA Memory error interrupt condition present 1210 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.35 LCD Write Protect Mode Register Name: LCD_WPMR Access: Read/Write 31 30 29 28 27 26 25 24 WPKEY 23 22 21 20 19 18 17 16 WPKEY 15 14 13 12 11 10 9 8 WPKEY 7 6 5 4 3 2 1 0 — — — — — — — WPEN • WPEN: Write Protect Enable 0: Disables the Write Protect if WPKEY corresponds to0x4C4344 (“LCD” in ASCII). 1: Enables the Write Protect if WPKEY corresponds to0x4C4344 (“LCD” in ASCII). Protects the registers: • “LCD Control Register 1” on page 1185 • “LCD Control Register 2” on page 1186 • “LCD Timing Configuration Register 1” on page 1188 • “LCD Timing Configuration Register 2” on page 1189 • “LCD Frame Configuration Register” on page 1190 • “LCD FIFO Register” on page 1191 • “LCDMOD Toggle Rate Value Register” on page 1192 • “Dithering Pattern DP1_2 Register” on page 1193 • “Dithering Pattern DP4_7 Register” on page 1194 • “Dithering Pattern DP3_5 Register” on page 1195 • “Dithering Pattern DP2_3 Register” on page 1196 • “Dithering Pattern DP5_7 Register” on page 1197 • “Dithering Pattern DP3_4 Register” on page 1198 • “Dithering Pattern DP4_5 Register” on page 1199 • “Dithering Pattern DP6_7 Register” on page 1200 • WPKEY: Write Protect Key Should be written at value 0x4C4344 (“LCD” in ASCII). Writing any other value in this field aborts the write operation of the WPEN bit. Always reads as 0. SAM9M11 [DATASHEET] 1211 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

47.12.36 LCD Write Protect Status Register Name: LCD_WPSR Address: 0x005008E8 Access: Read-only 31 30 29 28 27 26 25 24 — — — — — — — — 23 22 21 20 19 18 17 16 WPVSRC 15 14 13 12 11 10 9 8 WPVSRC 7 6 5 4 3 2 1 0 — — — — — — — WPVS • WPVS: Write Protect Enable 0: No Write Protect Violation has occurred since the last read of the LCD_WPSR. 1: A Write Protect Violation occurred since the last read of the LCD_WPSR. If this violation is an unauthorized attempt to write a protected register, the associated violation is reported into field WPVSRC. • WPVSRC: Write Protect Violation Source When WPVS is active, this field indicates the write-protected register (through address offset or code) in which a write access has been attempted. Note: Reading LCD_WPSR automatically clears all fields 1212 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48. Video Decoder (VDEC) 48.1 Description The multi-format Video Decoder (VDEC) enables compression or decompression of digital video signals for the formats H.264, MPEG-4/H.263, MPEG-2, MPEG-1, JPEG and VC-1. A prior introduction to these format standards is recommended and helpful in understanding the functionality of the decoder. 48.2 Embedded Characteristics  Little-endian and Big-endian support. Decoder supported standards:  MPEG-4 Simple and Advanced Profile, levels 0-5  H.264 Baseline Profile, levels 1-3.1  H.263 Profile 0, levels 10-70  VC-1 ̶ Simple Profile, Low and Medium Levels ̶ Main Profile, Low, Medium and High Levels ̶ Advanced Profile, Levels 0-3  MPEG-2 Main Profile, Low, Medium and High Levels  JPEG Profile Baseline DCT (sequential) and JFIF 1.02 file form Post-processor features:  Image up-scaling  Image down-scaling  YCbCr to RGB conversion  Dithering  Deinterlacing  Programmable alpha channel  Alpha blending  De-blocking filter for MPEG-4 simple profile/H.263  Image cropping / digital zoom  Picture in picture  Supported display size for picture in picture  Image rotation SAM9M11 [DATASHEET] 1213 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.3 Block Diagram Figure 48-1. Block Diagram Decoder Control Software Application Programming Interface MPEG-4/H.263 MPEG-2 Strm. H.264 Strm. VC-1 Strm JPEG Strm Strm. Header Header Header Header Header Decode Decode Decode Decode Decode Hardware Drivers y or m e System Bus M al n er xt E Bus Interface Alpha Output Inter/Intra MV VLC Blending Formatting Prediction Decode Decode De-blocking Overlap Inverse RLC Dithering Filter Smoothing Transformation Decode RGB AC/DC Scaling De-Interlace Rotation Conversion Prediction Decoder and Post-Processor Hardware 1214 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.3.1 Decoding Features 48.3.1.1 H.264 Features Table 48-1. H.264 Features Feature Decoder Support Input data format H.264 byte or NAL unit stream Output data format YCbCr 4:2:0 semi-planar 48 x 48 to 1280 x 720 Supported image size Step size 16 pixels Maximum frame rate 30 fps at 720*576 (1) Maximum bit rate 57.2 Mbps Error detection and concealment Supported Note: 1. Actual maximum frame rate is given for logic clock frequency and system bus frequency at 133MHz. 48.3.1.2 MPEG-4 / H.263 Features Table 48-2. MPEG-4 / H.263 Feature Decoder support Input data format MPEG-4 / H.263 elementary video stream Output data format YCbCr 4:2:0 semi-planar 48 x 48 to 1280 x 720(MPEG-4) Supported image size 48 x 48 to 720 x 576 (H.263) Step size 16 pixels Maximum frame rate 30 fps at 720*576 (1) Maximum bit rate 38.4 Mbps Error detection and concealment Supported Note: 1. Actual maximum frame rate is given for logic clock frequency and system bus frequency at 133MHz. 48.3.1.3 MPEG-2 Features Table 48-3. MPEG-2 Features Feature Decoder support Input data format MPEG-2 / MPEG-1 elementary video stream Output data format YCbCr 4:2:0 semi-planar 48 x 48 to 1280*720 Supported image size Step size 16 pixels Maximum frame rate 30 fps at 720*576 (1) Maximum bit rate 38.4 Mbps Error detection and concealment Supported Note: 1. Actual maximum frame rate is given for logic clock frequency and system bus frequency at 133MHz. SAM9M11 [DATASHEET] 1215 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.3.1.4 JPEG Features Table 48-4. JPEG Features Feature Decoder support JFIF file format 1.02 Input data format YCbCr 4:0:0, 4:2:0, 4:2:2 and 4:4:0 sampling formats Output data format YCbCr 4:0:0, 4:2:0, 4:2:2 and 4:4:0 semiplanar 48x48 to 4672 x 3504 (16.4 million pixels) Supported image size Step size 16 pixels Maximum data rate Up to 38 million pixels per second (1) Thumbnail decoding JPEG compressed thumbnails supported Error detection Supported Note: 1. Actual maximum data rate is given for a logic clock frequency at 133 MHz and for medium quality JPEG 48.3.1.5 VC-1 Features Table 48-5. VC-1 Features Feature Decoder support Input data format VC-1 stream Output data format YCbCr 4:2:0 semi-planar 48 x 48 to 1280 x 720 Supported image size Step size 16 pixels Maximum frame rate 30 fps at 720*576 (1) Maximum bit rate 45 Mbps Error detection and concealment Supported Note: 1. Actual maximum frame rate is given for logic clock frequency and system bus frequency at 133MHz. 1216 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.3.1.6 Post-processing Features Table 48-6. Post-processing Features Feature Post-processor Support YCbCr 4:2:0 planar Input data format YCbCr 4:2:0 planar YCbCr 4:2:2 (YUYV) Internal source: VDEC decoder Input image source External source: e.g., a software decoder or camera interface YCbCr 4:2:0 semi-planar YCbCr 4:2:2 (YUYV) Output data format Fully configurable ARGB channel lengths and locations inside 32 bits, e.g., ARGB 32-bit (8-8-8-8), RGB 16-bit (5-6-5), ARGB 16-bit (4-4-4-4) Input image size 48 x 48 to 4672 x 3504 (16 Mpixels) (combined mode) Step size 16 pixels Input image size (stand- 48 x 48 to 2048 x 2048 (4 Mpixels) alone mode) Step size 16 pixels 16 x 16 to 1280 x 720 Output image size Horizontal step size 8 Vertical step size 2 Bicubic polynomial interpolation with a four-tap horizontal kernel and a twotap vertical kernel Arbitrary, non-integer scaling ratio separately for both dimensions Image up-scaling Maximum output width is 3x the input width (within the maximum output image size limit) Maximum output height is 3x the input height – 2 pixels (within the maximum output image size limit) Proprietary averaging filter Image down-scaling Arbitrary, non-integer scaling ratio separately for both dimensions Unlimited down-scaling ratio (e.g., from 16Mpixel to QVGA) BT.601-5 compliant [12] YCbCr to RGB color BT.709 compliant [13] conversion User definable conversion coefficient Dithering 2x2 ordered dithering for 4-, 5- and 6-bit RGB channel precision Deinterlacing (2) Conditional area-based deinterlace filtering Constant eight bit value can be set to the alpha channel of the 24-bit RGB output data to control the Programmable alpha transparency of the output picture. The resulting 32-bit ARGB data can be used as input data for later channel alpha blending. Output image can be alpha blended with two rectangular areas.(1) YCbCr semi-planar 4:2:0 PP output format is not supported when performing alpha blending. Alpha blending The supported overlay input formats are following: - 8 bit alpha value + YCbCr 4:4:4, big endian channel order being A-Y-Cb-Cr, 8 bits each - 8 bit alpha value + 24 bit RGB, big endian channel order being A-R-G-B, 8 bits each RGB image contrast Segmented linear adjustment RGB image brightness Linear adjustment SAM9M11 [DATASHEET] 1217 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 48-6. Post-processing Features (Continued) Feature Post-processor Support RGB image color saturation Linear adjustment De-blocking filter for MPEG- Using a modified H.264 in-loop filter as a post-processing filter. Filtering has to be performed in 4 simple profile/H.263 combined mode. User definable start position, height and width. Can be used with scaling to perform digital zoom. Image cropping/digital zoom Usable only for JPEG or standalone mode. Picture in picture Output image can be written to any location inside video memory (1) Supported display size for Up to 1280 x 720 picture in picture Output image writing can be prevented on two rectangular areas in the image (1). The masking feature Output image masking is exclusive with alpha blending however it is possible to have one masking area and one blending area. Rotation 90, 180 or 270 degrees Image rotation(2) Horizontal flip Vertical flip Notes: 1. Step size in the start and end coordinates depends on the output picture format and the width of the data bus. 2. Usable in stand-alone post-processing mode only. 1218 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.3.2 Decoder Data Flow, Hardware Performs Entropy Decoding (VLC Mode) Note: Numbered references in the following text are illustrated in Figure 48-2. The decoder software starts decoding the first picture by parsing the stream headers (1). Software then setups the hardware control registers (picture size, stream start address etc.) and enables the hardware (2). In JPEG case, software parses VLC and QP tables from the stream and writes them to a contiguous memory area. In VC-1 case, software parses bitplane macroblock control from the stream and writes it to memory. Hardware decodes the picture by reading stream, VLC and QP tables for JPEG (3), and the reference pictures (4) (required for inter picture decoding) from the external memory. Hardware writes the decoded output picture to memory (5) one macroblock at a time. When the picture has been fully decoded, or the hardware has run out of stream data, it gives an interrupt with a proper status flag and provides stream end address for software to continue and returns to initial state. In case the hardware detects erroneous stream during decoding, it will return an error interrupt, and software will start concealing errors for the current picture. Depending on the selected concealment method, software may re- initialize the hardware in the SW entropy decode mode. The pictures following the corrupted one are decoded in the normal mode until the next error is detected. If post-processing is enabled, one or two additional image transfer operations will take place. If the decoded images are in display order (i.e., no picture re-ordering has been made when encoding the sequence), and rotation is not used, PP will process the pictures in pipeline with the decoder. Otherwise, it will first have to read the decoded image that is to be displayed next from the memory (6), and then write back the processed image (7). Figure 48-2. Multi-format Decoder and External Memory Data Flow in VLC Mode External Memory ARM Processor Core H.264 NAL 1 Unit Stream 3 2 AHB Bus 4 Decoded 5 Picture Buffer (6) Post-Processed 7 Picture Buffer Multiformat HW Decoder Core SAM9M11 [DATASHEET] 1219 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.3.3 Decoder Data Flow, Software Performs Entropy Decoding (RLC Mode) Note: Numbered references in the following text are illustrated in Figure 48-3 on page 1221. In this case, the decoder software starts decoding the first picture by parsing the stream headers (1), and by performing entropy decoding. Software then writes the following items to external memory:  Run-length-coded (RLC) data (2)  Differential motion vectors (3)  Intra 4x4 prediction modes (in H.264) or separate DC coefficients (in MPEG-4, if the stream is using data partitioning) (4)  Macroblock control data (5) Last step for the software is to write the hardware control registers and to enable the hardware (6). Hardware decodes the picture by buffering control data for several macroblocks at a time, and then reads appropriate amount of RLC data, differential motion vectors and intra modes depending on each macroblock type (7)–(10). Hardware will also read the reference pictures (previously decoded pictures) as required (11). Hardware writes decoded (in-loop filtered, if H.264) output picture to memory one macroblock at a time (12). When the picture has been fully decoded, hardware gives an interrupt and returns to initial state. If post-processing is enabled, one or two additional image transfer operations will take place. If the decoded images are in display order (i.e., no picture re-ordering has been made when encoding the sequence), and rotation is not used, PP will process the pictures in pipeline with the decoder. Otherwise, it will first have to read the decoded image that is to be displayed next from the memory (13), and then write back the processed image (14). 1220 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 48-3. Multi-format Decoder and External Memory Data Flow in RLC Mode External Memory ARM Processor Core H.264 NAL 1 Unit Stream 2 RLC Data 7 6 3 Differential AHB Bus Motion Vectors 8 4 Intra 4x4 9 Modes 5 Macroblock 10 Control Multiformat HW Decoder Core 11 Decoded 12 Picture Buffer (13) 14 Post-Processed Picture Buffer 48.4 Product Dependencies 48.4.1 Power Management The Video Decoder requires a peripheral clock. The user must enable the VDEC peripheral clock by setting the corresponding PIDx bit in the PMC Peripheral Clock Enable Register (PMC_PCER). Software can reset the hardware synchronically by writing separate decoder and post-processor enable bits to zero. These enable bits are located in the memory-mapped registers and they can be used for terminating or restarting the decoding or post-processing at any time. 48.4.2 Interrupt The Video Decoder has an interrupt line connected to the Advanced Interrupt Controller (AIC). The AIC must be programmed prior to handling Video Decoder interrupts. Table 48-7. Peripheral IDs Instance ID VDEC 30 SAM9M11 [DATASHEET] 1221 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.5 Video Decoder User Interface (VDEC) User Interface The VDEC User interface is split into two interfaces.  One that concerns Post Processor and is common to all Decoder Modes, described by Video Post Processor Register Mapping.  One in which registers and fields depend on the Decoder Mode used. For best readability this document describes one Register Mapping for each Decoder Mode. The relations are given in Table 48-8. Table 48-8. Register Mapping vs. Decoder Mode Decoder Mode Refer to the following Register Mapping H264 Video Decoder Register Mapping (H264) MPEG4 Video Decoder Register Mapping (MPEG4H263) H263 Video Decoder Register Mapping (MPEG4H263) JPEG Video Decoder Register Mapping (JPEG) VC1 Video Decoder Register Mapping (VC1) MPEG2 Video Decoder Register Mapping (MPEG2MPEG1) MPEG1 Video Decoder Register Mapping (MPEG2MPEG1) Note: The decoder mode is defined by the field DEC_MODE in Decoder Control Register 0. Table 48-9. Video Decoder Register Mapping (All Decoders) Offset Register (1) (2) (3) (4) (5) Name Access Reset 0x0000 ID Register X X X X X VDEC_IDR Read-only 0x81700880 0x0004 Decoder Interrupt Register X X X X X VDEC_DIR Read/Write 0x00000000 0x0008 Decoder Device Configuration Register X X X X X VDEC_DDCR Read/Write 0x00000400 0x000C Decoder Control Register 0 X X X X X VDEC_CTLR0 Read/Write 0x00000000 0x0010 Decoder Control Register 1 X X X X X VDEC_CTLR1 Read/Write 0x00000000 0x0014 Decoder Control Register 2 X X X X X VDEC_CTLR2 Read/Write 0x00000000 0x0018 Decoder Control Register 3 X X X X X VDEC_CTLR3 Read/Write 0x00000000 0x001C Decoder Control Register 4 X – – X – VDEC_CTLR4 Read/Write 0x00000000 0x0020 Decoder Control Register 5 X – – X – VDEC_CTLR5 Read/Write 0x00000000 0x0024 Decoder Control Register 6 X X – X – VDEC_CTLR6 Read/Write 0x00000000 0x0028 Base Address for Differential Motion Vector X X – X – VDEC_DMVBA Read/Write 0x00000000 0x002C Decoder Control Register 7 X X – X – VDEC_CTLR7 Read/Write 0x00000000 0x0030 RLC/VLC Data Base Address X X X X X VDEC_RLCVLCBA Read/Write 0x00000000 0x0034 Decoded Picture Base Address X X X X X VDEC_PICTBA Read/Write 0x00000000 0x0038 Reference Picture Index 0 Base Address X X X X X VDEC_PIDXBA0 Read/Write 0x00000000 0x003C Reference Picture Index 1 Base Address X X X X X VDEC_PIDXBA1 Read/Write 0x00000000 0x0040 Reference Picture Index 2 Base Address X X X X X VDEC_PIDXBA2 Read/Write 0x00000000 0x0044 Reference Picture Index 3 Base Address X X X X X VDEC_PIDXBA3 Read/Write 0x00000000 0x0048 Reference Picture Index 4 Base Address X X X X X VDEC_PIDXBA4 Read/Write 0x00000000 0x004C Reference Picture Index 5 Base Address X X X X – VDEC_PIDXBA5 Read/Write 0x00000000 1222 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 48-9. Video Decoder Register Mapping (All Decoders) (Continued) Offset Register (1) (2) (3) (4) (5) Name Access Reset 0x0050 Reference Picture Index 6 Base Address X X X X – VDEC_PIDXBA6 Read/Write 0x00000000 0x0054 Reference Picture Index 7 Base Address X X X – – VDEC_PIDXBA7 Read/Write 0x00000000 0x0058 Reference Picture Index 8 Base Address X – X – – VDEC_PIDXBA8 Read/Write 0x00000000 0x005C Reference Picture Index 9 Base Address X – X – – VDEC_PIDXBA9 Read/Write 0x00000000 0x0060 Reference Picture Index 10 Base Address X – X – – VDEC_PIDXBA10 Read/Write 0x00000000 0x0064 Reference Picture Index 11 Base Address X – X – – VDEC_PIDXBA11 Read/Write 0x00000000 0x0068 Reference Picture Index 12 Base Address X – X – – VDEC_PIDXBA12 Read/Write 0x00000000 0x006C Reference Picture Index 13 Base Address X – X X – VDEC_PIDXBA13 Read/Write 0x00000000 0x0070 Reference Picture Index 14 Base Address X – – – – VDEC_PIDXBA14 Read/Write 0x00000000 0x0074 Reference Picture Index 15 Base Address X – – – – VDEC_PIDXBA15 Read/Write 0x00000000 0x0078 Reference Picture Numbers Register 0 X – – – – VDEC_PNR0 Read/Write 0x00000000 0x007C Reference Picture Numbers Register 1 X – – – – VDEC_PNR1 Read/Write 0x00000000 0x0080 Reference Picture Numbers Register 2 X – – – – VDEC_PNR2 Read/Write 0x00000000 0x0084 Reference Picture Numbers Register 3 X – – – – VDEC_PNR3 Read/Write 0x00000000 0x0088 Reference Picture Numbers Register 4 X – – – – VDEC_PNR4 Read/Write 0x00000000 0x008C Reference Picture Numbers Register 5 X – – – – VDEC_PNR5 Read/Write 0x00000000 0x0090 Reference Picture Numbers Register 6 X – – – – VDEC_PNR6 Read/Write 0x00000000 0x0094 Reference Picture Numbers Register 7 X – – – – VDEC_PNR7 Read/Write 0x00000000 0x0098 Reference Picture Long Term Flag Register X – – – – VDEC_PLTFR Read/Write 0x00000000 0x009C Reference Picture Valid Flag Register X – – – – VDEC_PVFR Read/Write 0x00000000 0x00A0 Standard Dependent Tables Base Address X X X – X VDEC_SDTBA Read/Write 0x00000000 0x00A4 Direct Mode Motion Vector Base Address X X – X X VDEC_DMMVBA Read/Write 0x00000000 0x00A8 H264 Initial Reference Picture List Register 0 X – – – – VDEC_IRPLR0 Read/Write 0x00000000 0x00AC H264 Initial Reference Picture List Register 1 X – – – – VDEC_IRPLR1 Read/Write 0x00000000 0x00B0 H264 Initial Reference Picture List Register 2 X – – – – VDEC_IRPLR2 Read/Write 0x00000000 0x00B4 H264 Initial Reference Picture List Register 3 X – – – – VDEC_IRPLR3 Read/Write 0x00000000 0x00B8 H264 Initial Reference Picture List Register 4 X – – – – VDEC_IRPLR4 Read/Write 0x00000000 0x00BC H264 Initial Reference Picture List Register 5 X – – – – VDEC_IRPLR5 Read/Write 0x00000000 0x00C0 Error Concealment Register X X – X X VDEC_ECR Read/Write 0x00000000 0x00C4 Reserved – – – – – – – – 0x00C8 Reserved – – – – – – – – Notes: 1. Used in H.264 mode. 2. Used in MPEG-4/H.263 decoder mode. 3. Used in JPEG decoder mode. 4. Used in VC-1 decoder mode. 5. Used in MPEG-2/MPEG-1 mode. SAM9M11 [DATASHEET] 1223 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6 Video Decoder Register Mapping (H.264) Table 48-10. Video Decoder Register Mapping (H264) Offset Register Name Access Reset 0x0000 ID Register VDEC_IDR Read-Only 0x81700880 0x0004 Decoder Interrupt Register VDEC_DIR Read/Write 0x00000000 0x0008 Decoder Device Configuration Register VDEC_DDCR Read/Write 0x00000400 0x000C Decoder Control Register 0 VDEC_CTLR0 Read/Write 0x00000000 0x0010 Decoder Control Register 1 VDEC_CTLR1 Read/Write 0x00000000 0x0014 Decoder Control Register 2 VDEC_CTLR2 Read/Write 0x00000000 0x0018 Decoder Control Register 3 VDEC_CTLR3 Read/Write 0x00000000 0x001C Decoder Control Register 4 VDEC_CTLR4 Read/Write 0x00000000 0x0020 Decoder Control Register 5 VDEC_CTLR5 Read/Write 0x00000000 0x0024 Decoder Control Register 6 VDEC_CTLR6 Read/Write 0x00000000 0x0028 Base Address for Differential Motion Vector VDEC_DMVBA Read/Write 0x00000000 0x002C Decoder Control Register 7 VDEC_CTLR7 Read/Write 0x00000000 0x0030 RLC/VLC Data Base Address VDEC_RLCVLCBA Read/Write 0x00000000 0x0034 Decoded Picture Base Address VDEC_PICTBA Read/Write 0x00000000 0x0038 Reference Picture Index 0 Base Address VDEC_PIDXBA0 Read/Write 0x00000000 0x003C Reference Picture Index 1 Base Address VDEC_PIDXBA1 Read/Write 0x00000000 0x0040 Reference Picture Index 2 Base Address VDEC_PIDXBA2 Read/Write 0x00000000 0x0044 Reference Picture Index 3 Base Address VDEC_PIDXBA3 Read/Write 0x00000000 0x0048 Reference Picture Index 4 Base Address VDEC_PIDXBA4 Read/Write 0x00000000 0x004C Reference Picture Index 5 Base Address VDEC_PIDXBA5 Read/Write 0x00000000 0x0050 Reference Picture Index 6 Base Address VDEC_PIDXBA6 Read/Write 0x00000000 0x0054 Reference Picture Index 7 Base Address VDEC_PIDXBA7 Read/Write 0x00000000 0x0058 Reference Picture Index 8 Base Address VDEC_PIDXBA8 Read/Write 0x00000000 0x005C Reference Picture Index 9 Base Address VDEC_PIDXBA9 Read/Write 0x00000000 0x0060 Reference Picture Index 10 Base Address VDEC_PIDXBA10 Read/Write 0x00000000 0x0064 Reference Picture Index 11 Base Address VDEC_PIDXBA11 Read/Write 0x00000000 0x0068 Reference Picture Index 12 Base Address VDEC_PIDXBA12 Read/Write 0x00000000 0x006C Reference Picture Index 13 Base Address VDEC_PIDXBA13 Read/Write 0x00000000 0x0070 Reference Picture Index 14 Base Address VDEC_PIDXBA14 Read/Write 0x00000000 0x0074 Reference Picture Index 15 Base Address VDEC_PIDXBA15 Read/Write 0x00000000 0x0078 Reference Picture Numbers Register 0 VDEC_PNR0 Read/Write 0x00000000 0x007C Reference Picture Numbers Register 1 VDEC_PNR1 Read/Write 0x00000000 0x0080 Reference Picture Numbers Register 2 VDEC_PNR2 Read/Write 0x00000000 0x0084 Reference Picture Numbers Register 3 VDEC_PNR3 Read/Write 0x00000000 0x0088 Reference Picture Numbers Register 4 VDEC_PNR4 Read/Write 0x00000000 1224 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 48-10. Video Decoder Register Mapping (H264) (Continued) Offset Register Name Access Reset 0x008C Reference Picture Numbers Register 5 VDEC_PNR5 Read/Write 0x00000000 0x0090 Reference Picture Numbers Register 6 VDEC_PNR6 Read/Write 0x00000000 0x0094 Reference Picture Numbers Register 7 VDEC_PNR7 Read/Write 0x00000000 0x0098 Reference Picture Long Term Flag Register VDEC_PLTFR Read/Write 0x00000000 0x009C Reference Picture Valid Flag Register VDEC_PVFR Read/Write 0x00000000 0x00A0 Standard Dependent Tables Base Address VDEC_SDTBA Read/Write 0x00000000 0x00A4 Direct Mode Motion Vector Base Address VDEC_DMMVBA Read/Write 0x00000000 0x00A8 H264 Initial Reference Picture List Register 0 VDEC_IRPLR0 Read/Write 0x00000000 0x00AC H264 Initial Reference Picture List Register 1 VDEC_IRPLR1 Read/Write 0x00000000 0x00B0 H264 Initial Reference Picture List Register 2 VDEC_IRPLR2 Read/Write 0x00000000 0x00B4 H264 Initial Reference Picture List Register 3 VDEC_IRPLR3 Read/Write 0x00000000 0x00B8 H264 Initial Reference Picture List Register 4 VDEC_IRPLR4 Read/Write 0x00000000 0x00BC H264 Initial Reference Picture List Register 5 VDEC_IRPLR5 Read/Write 0x00000000 0x00C0 Error Concealment Register VDEC_ECR Read/Write 0x00000000 0x00C4 Reserved – – – 0x00C8 Reserved – – – SAM9M11 [DATASHEET] 1225 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.1 Video Decoder ID Register Name: VDEC_IDR Address: 0x00900000 Access: Read-Only 31 30 29 28 27 26 25 24 PROD_ID 23 22 21 20 19 18 17 16 PROD_ID 15 14 13 12 11 10 9 8 MAJOR_VER MINOR_VER 7 6 5 4 3 2 1 0 MINOR_VER BUILD_VER • BUILD_VER: Build Version Build Version is 0x0. • MINOR_VER: Minor Version Minor Version is 0x88 • MAJOR_VER: Major Version Major Version is 0x0. • PROD_ID: Product ID Product ID is 0x8170. 1226 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.2 Decoder Interrupt Register Name: VDEC_DIR Address: 0x00900004 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – TO JPEGSD ISE 15 14 13 12 11 10 9 8 ASOD SBE BE DR – – – ISET 7 6 5 4 3 2 1 0 – – – ID – – – DE • DE: Decoder Enable 0: Disables Decoder. 1: Enables Decoder. Setting this bit high will start the decoding operation. Hardware will reset this bit when a picture is processed, a stream error or ASO is detected or a bus error is received. • ID: Interrupt Disable 0: Enables Interrupts for decoder. 1: Disables Interrupts for decoder. When high, there will be no interrupts issued by the decoder. Polling must be used to see the hardware status. • ISET: Decoder Interrupt Set 0: Clears the Decoder Interrupt. Software will reset this after the interrupt is handled. 1: Sets the decoder interrupt. This bit drives the interrupt line, OR gated with the post-processor interrupt bit. The interrupt line is not used for the decoder if the interrupt disable bit for decoder is high. • DR: Decoder Ready 0: Decoding in progress. 1: Decoder is ready. When high, the hardware has decoded a picture. Hardware will self-reset. • BE: Bus Error 0: No error. 1: A bus error has occurred. When high, hardware has received an error response from the bus while accessing external memory. This is a fatal error possibly caused by the incorrect allocation of decoder linear memory. Hardware will self-reset. SAM9M11 [DATASHEET] 1227 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• SBE: Stream Buffer Empty 0: Stream Buffer is not empty. 1: Input Stream Buffer is empty but the picture is not ready. Software must provide a new stream pointer to hardware. Hardware will not self-reset. • ASOD: ASO Detected 0: No ASO detected. 1: Interrupt status flag ASO detected. Hardware has encountered Arbitrary Slice Order tool in the input H.264 stream data, and software must perform entropy decoding. Hardware will self-reset. • ISE: Input Stream Error 0: No Error. 1: Interrupt Stream Error occurs. When high, hardware has encountered a bit error in the input stream data, and software must perform error concealment. Hardware will self-reset. • JPEGSD: JPEG Slice Decoded 0: No Decoding. 1: JPEG slice decoded. Hardware has decoded the requested amount of macroblock rows of a JPEG picture. When high, the SW must set a new base addresses for the decoder output. Hardware will not self-reset. • TO: Timeout 0: No Timeout. 1: Timeout occurs. When high, decoder has made no bus transactions in 218-1 clock cycles and has not set an interrupt. Possible only if time- out interrupting is enabled. This should be considered as an encountered error in the input stream. Note: Post-processor transactions affect this feature; running stand-alone post-processing while decoding may prevent decoder timeout interrupts. 1228 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.3 Decoder Device Configuration Register Name: VDEC_DDCR Address: 0x00900008 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 HTI – DI_LE – – AHB_BURST DOPF LAT_COMP 15 14 13 12 11 10 9 8 LAT_COMP DDCGE INTCE_LE DO_LE 7 6 5 4 3 2 1 0 PRIOR MAX_BURST_LEN • MAX_BURST_LEN: Maximum Burst Length for Decoder Bus Transactions Valid values for AHB are 0, 1, 4, 8, 16 and 17. 0: INCR transfer type is used always. 1: SINGLE transfer type is used always. 4: INCR4, INCR and SINGLE transfers are allowed. INCR used for 2 and 3 bursts. 8: INCR8, INCR4, INCR and SINGLE transfers are allowed. INCR used for 2 and 3 bursts. 16: INCR16, INCR8, INCR4, INCR and SINGLE transfers are allowed. INCR used for 2 and 3 bursts. 17: INCR16, INCR8, INCR4, INCR and SINGLE transfers are allowed. INCR used for 2, 3, 5, 6, 7, 9, 10, 11, 12, 13, 14 and 15 bursts. • PRIOR: Decoder Core Internal Bus Service Priority 0: Dynamic priority depending on stream content. 1: Post-processor output write has highest priority. 2: Input stream read has highest priority. 3: Reference picture read has highest priority, then post-processor transactions. 4: Reference picture read has highest priority, then decoder output write. • DO_LE: Decoder Output Endian Mode 0: Big endian 1: Little endian • INTCE_LE: Interface Endian Mode 0: Big endian 1: Little endian SAM9M11 [DATASHEET] 1229 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DDCGE: Decoder Dynamic Clock Gating Enable 0: Clock is running for all structures. 1: Clock is gated for decoder structures that are not used. Clock gating value should be changed only when the decoder is disabled. • LAT_COMP: Decoder Latency Compensation Decoder latency compensation value in clock cycles. If the best case latency (from bus request to bus grant, or from data request to data receive) is known, the value can be written to these register bits used to compensate the delay. If the latency value is unknown, these bits should be written to zero. Note: Setting the compensation value higher than the best case latency can cause data corruption. • DOPF: Decoder Output Picture Format 0: Output format is raster scan, i.e., pixel rows are written in consecutive memory. 1: Output format is tiled, i.e., macroblocks are written in consecutive memory addresses. • AHB_BURST: AHB Precise Burst and Data Discard Enable 0: INCR bursts of undefined length 2 or 3 may be issued when necessary. 1: Only the precise AHB bursts (SINGLE, INCR4, INCR8 and INCR16) are used in SDRAM read accesses. Extra data is discarded internally. • DI_LE: Decoder Input Endian Mode 0: Big endian. 1: Little endian. • HTI: Hardware Timeout Interrupt Enable 0:Hardware Timeout Interrupt Disable. 1: Hardware Timeout Interrupt Enable. 1230 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.4 Decoder Control Register 0 (Decoder Mode and Picture Type) Name: VDEC_CTLR0 Address: 0x0090000C Access: Read/Write 31 30 29 28 27 26 25 24 DEC_MODE RLCEN – – – 23 22 21 20 19 18 17 16 PICMODE PICSTRUCT PICBEN PICTYPE PICFIELD FORWMODE – REFFIELD 15 14 13 12 11 10 9 8 OUTDIS FILTDIS QUANT MV REFFIRST – – HLOCK 7 6 5 4 3 2 1 0 – – – – – – – – • HLOCK: HLOCK Enable 0: locked transfers disabled. 1: locked transfers enabled. When a locked transfer is granted, bus grant cannot be lost even if a higher priority master requests the bus. • REFFIRST: Reference Field First Indicates which FWD reference field has been decoded first. 0: FWD reference bottom field. 1: FWD reference top field. • MV: MPEG-2 Motion Vector Write Enable Direct mode motion vector write enable / MPEG2 motion vector write enable for error concealment purposes: 0: Writing disabled for current picture. 1: The direct mode motion vectors are written to external memory starting from MV_BASE in Direct mode motion vector write/read base address register (offset 0x00a8). • QUANT: Quantization 0: Quantization parameter can vary inside picture. 1: Quantization parameter is fixed (pquant). • FILTDIS: De-block Filtering Disable 0: Filtering is enabled for current picture. 1: Filtering is disabled for current picture. • OUTDIS: Disable Decoder Output Picture Writing 0: Decoder output picture is written to external memory. 1: Decoder output picture is not written to external memory. SAM9M11 [DATASHEET] 1231 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• REFFIELD: Indicates Which Field Should Be Used As Reference Used only if REF_FRAMES =’0’ in Decoder control register 1 (picture parameters). 0: Bottom field 1: Top field • FORWMODE: Coding Mode of Forward Reference Picture 0: Progressive 1: Interlaced Note: For backward reference picture the coding mode is always the same as for current picture. • PICFIELD: Picture Field If field structure is enabled this bit informs which one of the fields is being decoded: 0: Bottom field 1: Top field • PICTYPE: Picture Type 0: Intra type (I) 1: Inter type (P) • PICBEN: B Picture Enable B picture enable for current picture: 0: Picture type is I or P depending on PICTYPE. 1: Picture type is BI (vc1)/D (mpeg1) or B depending on PICTYPE. • PICSTRUCT: Structure of the Current Picture Structure of the current picture (residual structure). 0: Frame structure, For H.264 this means MBAFF structured picture for interlaced sequence. 1: Field structure • PICMODE: Coding mode of Current Picture 0: Progressive 1: Interlaced • RLCEN: RLC Mode Enable 0: Decode from input stream (VLC mode). 1: Decode from RLC input data. 1232 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DEC_MODE: Decoding Mode 0: H.264 1: MPEG-4 2: H.263 3: JPEG 4: VC-1 5: MPEG2 6: MPEG1 7: Reserved SAM9M11 [DATASHEET] 1233 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.5 Decoder Control Register 1 (Picture Parameters) Name: VDEC_CTLR1 Address: 0x00900010 Access: Read/Write 31 30 29 28 27 26 25 24 PIC_WIDTH 23 22 21 20 19 18 17 16 PIC_WIDTH WIDTH_OFF PIC_HEIGHT 15 14 13 12 11 10 9 8 PIC_HEIGHT HEIGHT_OFF 7 6 5 4 3 2 1 0 HEIGHT_OFF AVSM TOPF REF_FRAMES • REF_FRAMES: Number of Reference Frames/Semantics H.264: maximum number of short and long term reference frames in decoded picture buffer. VC-1: maximum number of semantics. • TOPF: Top Field Top field is first information for MPEG4 or VC-1. • AVSM: Alternative Vertical Scan Method indicates alternative vertical scan method used for interlaced frames • HEIGHT_OFF: Height Offset In VC-1 decoding mode only. The amount of meaningful vertical pixels in last macroblock (height offset) 0 if exactly 16 pix- els multiple picture and all the vertical pixels in last macroblock are meaningful. • PIC_HEIGHT: Picture Height Picture height in macroblocks = ((height in pixels+15)/16). Picture height is informed as size of the (progressive) frame even though a single field (of interlaced content) is being decoded. • WIDTH_OFF: Width Offset In VC-1 decoding mode only. The amount of meaningful horizontal pixels in last macroblock (width offset) 0 if exactly 16pixels multiple picture and all the horizontal pixels in last macroblock are meaningful. • PIC_WIDTH: Picture Width Picture width in macroblocks = ((width in pixels + 15) /16). 1234 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.6 Decoder Control Register 2 (H.264 Stream Decoding Table Selects) Name: VDEC_CTLR2 Address: 0x00900014 Access: Read/Write 31 30 29 28 27 26 25 24 STREAM_START_BIT – – 23 22 21 20 19 18 17 16 QPFILT_CB_OFF QPFILT_CR_OFF 15 14 13 12 11 10 9 8 QPFILT_CR_OFF – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – FIELDPIC • FIELDPIC: Flag for Stream 1: Field picture flag exists in stream. • QPFILT_CR_OFF: Chrominance Offset Chroma Qp filter offset for Cr type. • QPFILT_CB_OFF: Chrominance Offset Chroma Qp filter offset for Cb type. • STREAM_START_BIT: Stream Start Bit Exact bit of stream start word where decoding can be started. SAM9M11 [DATASHEET] 1235 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.7 Decoder Control Register 3 (Stream Buffer Information) Name: VDEC_CTLR3 Address: 0x00900018 Access: Read/Write 31 30 29 28 27 26 25 24 ST_COD_EN INIT_QP – 23 22 21 20 19 18 17 16 STREAM_LEN 15 14 13 12 11 10 9 8 STREAM_LEN 7 6 5 4 3 2 1 0 STREAM_LEN • STREAM_LEN: Stream Length Amount of stream data bytes in input buffer. If the given buffer size is not enough for finishing the picture the corresponding interrupt is given and new stream buffer base address and stream buffer size information should be given. For VC-1 the buffer must include data for one picture/slice of the picture. For H264/MPEG4/H263/MPEG2/MPEG1 the buffer must include at least data for one slice/VP of the picture. For JPEG the buffer size must be a multiple of 256 bytes or the amount of data for one picture. • INIT_QP: Quantization Initialization Initial value for quantization parameter (picture quantizer). • ST_COD_EN: Stream Start Code Stream start codes exist: 0: Stream does not contain start codes. 1: Stream contains start codes. 1236 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.8 Decoder Control Register 4 (H.264 Control) Name: VDEC_CTLR4 Address: 0x0090001C Access: Read/Write 31 30 29 28 27 26 25 24 CABAC BW DIRMV_PRED W_PRED W_BIPR – – 23 22 21 20 19 18 17 16 – – – FRAME_NUM_LEN 15 14 13 12 11 10 9 8 FRAME_NUM 7 6 5 4 3 2 1 0 FRAME_NUM • FRAME_NUM: Frame Number Current Frame Number, used to identify short-term reference frames. Used in reference picture reordering. • FRAME_NUM_LEN: Frame Number length Bit length of frame_num in data stream. • W_BIPR: Weight Prediction for B Slices H.264 weighted prediction specification for B slices. • W_PRED: Weight Prediction H.264 weighted prediction enable for P slices. • DIRMV_PRED: Derive Luma Method Specifies the method to use to derive luma motion vectors. • BW: Black and White Enable 0: 4:2:0 sampling format 1: 4:0:0 sampling format • CABAC: H.264 CABAC Enable 0: CABAC disable. 1: CABAC enable. SAM9M11 [DATASHEET] 1237 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.9 Decoder Control Register 5 (H.264 Control) Name: VDEC_CTLR5 Address: 0x00900020 Access: Read/Write 31 30 29 28 27 26 25 24 CONS_INTRA FILT_CTRL RD_PIC T8X8FE REF_PIC_LEN 23 22 21 20 19 18 17 16 REF_PIC_LEN IDREN 15 14 13 12 11 10 9 8 IDR_PIC_ID 7 6 5 4 3 2 1 0 IDR_PIC_ID • IDR_PIC_ID: IDR Picture Identifies IDR (instantaneous decoding refresh) picture. • IDREN: IDR Picture Enable IDR (instantaneous decoding refresh) picture flag. • REF_PIC_LEN: Reference Picture Length Length of decoded reference picture marking bits. • T8X8FE: 8x8 Transform Flag Enable 8x8 transform flag enable • RD_PIC: Redundant Picture Present Specifies whether redundant picture count syntax elements are present in the slice header. • FILT_CTRL: Extra Variables Controlling Characteristics of The Deblocking Filter Indicates whether extra variables controlling characteristics of the deblocking filter are present in the slice header. • CONS_INTRA: Intra in Prediction 1: Specifies that intra prediction uses only neighboring intra macroblocks in prediction. 0: Also neighboring inter macroblocks are used in intra prediction process. 1238 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.10 Decoder Control Register 6 (H.264 RLC Mode) Name: VDEC_CTLR6 Address: 0x00900024 Access: Read/Write 31 30 29 28 27 26 25 24 PPS_ID 23 22 21 20 19 18 17 16 REF_IDX1 REF_IDX0 15 14 13 12 11 10 9 8 REF_IDX0 – – – – – – 7 6 5 4 3 2 1 0 POC_LEN • POC_LEN: Picture Order length Length of picture order count field in stream. • REF_IDX0: Maximum Reference Index 0 Specifies the maximum reference index that can be used while decoding inter predicted macro blocks. This is same as in previous decoders (width increased with q bit). • REF_IDX1: Maximum Reference Index 1 Specifies the maximum reference index that can be used while decoding inter predicted macro blocks. • PPS_ID: Picture Parameter pic_parameter_set_id, identifies the picture parameter set that is referred to in the slice header. SAM9M11 [DATASHEET] 1239 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.11 Decoder Control Register 6 (H.264 VLC Mode) Name: VDEC_CTLR6 Address: 0x00900024 Access: Read/Write 31 30 29 28 27 26 25 24 MB_CONTROL_BASE 23 22 21 20 19 18 17 16 MB_CONTROL_BASE 15 14 13 12 11 10 9 8 MB_CONTROL_BASE 7 6 5 4 3 2 1 0 MB_CONTROL_BASE – – • MB_CONTROL_BASE: Macroblock Control Base Address 1240 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.12 Differential Motion Vector Base Address (H.264, MPEG-4/H.263) Name: VDEC_DMVBA Address: 0x00900028 Access: Read/Write 31 30 29 28 27 26 25 24 MV_CONTROL_BASE 23 22 21 20 19 18 17 16 MV_CONTROL_BASE 15 14 13 12 11 10 9 8 MV_CONTROL_BASE 7 6 5 4 3 2 1 0 MV_CONTROL_BASE • MV_CONTROL_BASE: Differential Motion Vector Base Address SAM9M11 [DATASHEET] 1241 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.13 Decoder Control Register 7 (H264, MPEG-4/H.263) Name: VDEC_CTLR7 Address: 0x0090002C Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address H.264: Intra prediction 4x4 mode base address MPEG-4: DC component base address 1242 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.14 RLC/VLC Data Base Address Name: VDEC_RLCVLCBA Address: 0x00900030 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address RLC_mode: Base address for RLC data (RLCEN = 1 in Decoder Control Register 0). VLC_mode: Stream start address/end address with byte precision (RLCEN = 0 in Decoder Control Register 0) STREAM_START_BIT field in Decoder Control Register 0. When SBE = 1 or DE = 0 in Decoder Interrupt Register, this register contains HW return value of last byte address (not valid for jpeg) where stream has been read (and used) in accu- racy of byte. For debug purposes, the last byte address is also written when stream error/ASO is detected even though it may not be accurate. SAM9M11 [DATASHEET] 1243 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.15 Decoded Picture Base Address (Video, JPEG Decoder Output Luma Picture) Name: VDEC_PICTBA Address: 0x00900034 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Video: Base address for decoder output picture. Points directly to start of decoder output picture or field. 1244 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.16 Reference Picture Index Base Address (H.264) Name: VDEC_PIDXBAx [x=0..15] Address: 0x00900038 [0], 0x0090003C [1], 0x00900040 [2], 0x00900044 [3], 0x00900048 [4], 0x0090004C [5], 0x00900050 [6], 0x00900054 [7], 0x00900058 [8], 0x0090005C [9], 0x00900060 [10], 0x00900064 [11], 0x00900068 [12], 0x0090006C [13], 0x00900070 [14], 0x00900074 [15] Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for reference picture index 0..15. SAM9M11 [DATASHEET] 1245 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.17 Reference Picture Number Register 0 (H.264) Name: VDEC_PNR0 Address: 0x00900078 Access: Read/Write 31 30 29 28 27 26 25 24 REFER1 23 22 21 20 19 18 17 16 REFER1 15 14 13 12 11 10 9 8 REFER0 7 6 5 4 3 2 1 0 REFER0 • REFERx: Reference Picture Number for Index x 1246 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.18 Reference Picture Number Register 1 (H.264) Name: VDEC_PNR1 Address: 0x0090007C Access: Read/Write 31 30 29 28 27 26 25 24 REFER3 23 22 21 20 19 18 17 16 REFER3 15 14 13 12 11 10 9 8 REFER2 7 6 5 4 3 2 1 0 REFER2 • REFERx: Reference Picture Number for Index x SAM9M11 [DATASHEET] 1247 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.19 Reference Picture Number Register 2 (H.264) Name: VDEC_PNR2 Address: 0x00900080 Access: Read/Write 31 30 29 28 27 26 25 24 REFER5 23 22 21 20 19 18 17 16 REFER5 15 14 13 12 11 10 9 8 REFER4 7 6 5 4 3 2 1 0 REFER4 • REFERx: Reference Picture Number for Index x 1248 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.20 Reference Picture Number Register 3 (H.264) Name: VDEC_PNR3 Address: 0x00900084 Access: Read/Write 31 30 29 28 27 26 25 24 REFER7 23 22 21 20 19 18 17 16 REFER7 15 14 13 12 11 10 9 8 REFER6 7 6 5 4 3 2 1 0 REFER6 • REFERx: Reference Picture Number for Index x SAM9M11 [DATASHEET] 1249 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.21 Reference Picture Number Register 4 (H.264) Name: VDEC_PNR4 Address: 0x00900088 Access: Read/Write 31 30 29 28 27 26 25 24 REFER9 23 22 21 20 19 18 17 16 REFER9 15 14 13 12 11 10 9 8 REFER8 7 6 5 4 3 2 1 0 REFER8 • REFERx: Reference Picture Number for Index x 1250 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.22 Reference Picture Number Register 5 (H.264) Name: VDEC_PNR5 Address: 0x0090008C Access: Read/Write 31 30 29 28 27 26 25 24 REFER11 23 22 21 20 19 18 17 16 REFER11 15 14 13 12 11 10 9 8 REFER10 7 6 5 4 3 2 1 0 REFER10 • REFERx: Reference Picture Number for Index x SAM9M11 [DATASHEET] 1251 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.23 Reference Picture Number Register 6 (H.264) Name: VDEC_PNR6 Address: 0x00900090 Access: Read/Write 31 30 29 28 27 26 25 24 REFER13 23 22 21 20 19 18 17 16 REFER13 15 14 13 12 11 10 9 8 REFER12 7 6 5 4 3 2 1 0 REFER12 • REFERx: Reference Picture Number for Index x 1252 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.24 Reference Picture Number Register 7 (H.264) Name: VDEC_PNR7 Address: 0x00900094 Access: Read/Write 31 30 29 28 27 26 25 24 REFER15 23 22 21 20 19 18 17 16 REFER15 15 14 13 12 11 10 9 8 REFER14 7 6 5 4 3 2 1 0 REFER14 • REFERx: Reference Picture Number for Index x SAM9M11 [DATASHEET] 1253 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.25 Reference Picture Long Term Flag Register (H.264) Name: VDEC_PLTFR Address: 0x00900098 Access: Read/Write 31 30 29 28 27 26 25 24 LTF 23 22 21 20 19 18 17 16 LTF 15 14 13 12 11 10 9 8 LTF 7 6 5 4 3 2 1 0 LTF • LTF: Long Term Flag Long term reference picture index. 1254 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.26 Reference Picture Valid Flag Register (H.264) Name: VDEC_PVFR Address: 0x0090009C Access: Read/Write 31 30 29 28 27 26 25 24 VF 23 22 21 20 19 18 17 16 VF 15 14 13 12 11 10 9 8 VF 7 6 5 4 3 2 1 0 VF • VF: Valid Flag Valid flag for reference picture index. SAM9M11 [DATASHEET] 1255 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.27 Standard Dependent Tables Base Address Name: VDEC_SDTBA Address: 0x009000A0 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for standard dependent tables 1256 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.28 Direct Mode Motion Vector Base Address Name: VDEC_DMMVBA Address: 0x009000A4 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Not used in JPEG mode. SAM9M11 [DATASHEET] 1257 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.29 H264 Initial Reference Picture List Register 0 (H.264) Name: VDEC_IRPLR0 Address: 0x009000A8 Access: Read/Write 31 30 29 28 27 26 25 24 – – IREFL_BW2 IREFL_FW2 23 22 21 20 19 18 17 16 IREFL_FW2 IREFL_BW1 15 14 13 12 11 10 9 8 IREFL_BW1 IREFL_FW1 IREFL_BW0 7 6 5 4 3 2 1 0 IREFL_BW0 IREFL_FW0 • IREFL_FWx: Initial Reference Picture List for Forward Picid x • IREFL_BWy: Initial Reference Picture List for Backward Picid y 1258 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.30 H264 Initial Reference Picture List Register 1 (H.264) Name: VDEC_IRPLR1 Address: 0x009000AC Access: Read/Write 31 30 29 28 27 26 25 24 – – IREFL_BW5 IREFL_FW5 23 22 21 20 19 18 17 16 IREFL_FW5 IREFL_BW4 15 14 13 12 11 10 9 8 IREFL_BW4 IREFL_FW4 IREFL_BW3 7 6 5 4 3 2 1 0 IREFL_BW3 IREFL_FW3 • IREFL_FWx: Initial Reference Picture List for Forward Picid x • IREFL_BWy: Initial Reference Picture List for Backward Picid y SAM9M11 [DATASHEET] 1259 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.31 H264 Initial Reference Picture List Register 2 (H.264) Name: VDEC_IRPLR2 Address: 0x009000B0 Access: Read/Write 31 30 29 28 27 26 25 24 – – IREFL_BW8 IREFL_FW8 23 22 21 20 19 18 17 16 IREFL_FW8 IREFL_BW7 15 14 13 12 11 10 9 8 IREFL_BW7 IREFL_FW7 IREFL_BW6 7 6 5 4 3 2 1 0 IREFL_BW6 IREFL_FW6 • IREFL_FWx: Initial Reference Picture List for Forward Picid x • IREFL_BWy: Initial Reference Picture List for Backward Picid y 1260 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.32 H264 Initial Reference Picture List Register 3 (H.264) Name: VDEC_IRPLR3 Address: 0x009000B4 Access: Read/Write 31 30 29 28 27 26 25 24 – – IREFL_BW11 IREFL_FW11 23 22 21 20 19 18 17 16 IREFL_FW11 IREFL_BW10 15 14 13 12 11 10 9 8 IREFL_BW10 IREFL_FW10 IREFL_BW9 7 6 5 4 3 2 1 0 IREFL_BW9 IREFL_FW9 • IREFL_FWx: Initial Reference Picture List for Forward Picid x • IREFL_BWy: Initial Reference Picture List for Backward Picid y SAM9M11 [DATASHEET] 1261 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.33 H264 Initial Reference Picture List Register 4 (H.264) Name: VDEC_IRPLR4 Address: 0x009000B8 Access: Read/Write 31 30 29 28 27 26 25 24 – – IREFL_BW14 IREFL_FW14 23 22 21 20 19 18 17 16 IREFL_FW14 IREFL_BW13 15 14 13 12 11 10 9 8 IREFL_BW13 IREFL_FW13 IREFL_BW12 7 6 5 4 3 2 1 0 IREFL_BW12 IREFL_FW12 • IREFL_FWx: Initial Reference Picture List for Forward Picid x • IREFL_BWy: Initial Reference Picture List for Backward Picid y 1262 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.34 H264 Initial Reference Picture List Register 5 (H.264) Name: VDEC_IRPLR5 Address: 0x009000BC Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – IREFL_BW15 7 6 5 4 3 2 1 0 IREFL_BW15 IREFL_FW15 • IREFL_FW15: Initial Reference Picture List for Forward Picid 15 • IREFL_BW15: Initial Reference Picture List for Backward Picid 15 SAM9M11 [DATASHEET] 1263 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.6.35 Error Concealment Register Name: VDEC_ECR Address: 0x009000C0 Access: Read/Write 31 30 29 28 27 26 25 24 STARTMB_X 23 22 21 20 19 18 17 16 STARTMB_X STARTMB_Y 15 14 13 12 11 10 9 8 STARTMB_Y – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – – • STARTMB_Y: Start MB from SW for Y Dimension Used in error concealment case. Not used in JPEG mode. • STARTMB_X: Start MB from SW for X Dimension Used in error concealment case. Not used in JPEG mode. 1264 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7 Video Decoder Register Mapping (MPEG-4/H.263) Table 48-11. Video Decoder Register Mapping (MPEG4H263) Offset Register Name Access Reset 0x0000 ID Register VDEC_IDR Read-Only 0x81700880 0x0004 Decoder Interrupt Register VDEC_DIR Read/Write 0x00000000 0x0008 Decoder Device Configuration Register VDEC_DDCR Read/Write 0x00000400 0x000C Decoder Control Register 0 VDEC_CTLR0 Read/Write 0x00000000 0x0010 Decoder Control Register 1 VDEC_CTLR1 Read/Write 0x00000000 0x0014 Decoder Control Register 2 VDEC_CTLR2 Read/Write 0x00000000 0x0018 Decoder Control Register 3 VDEC_CTLR3 Read/Write 0x00000000 0x001C–0x0020 Reserved – – – 0x0024 Decoder Control Register 6 VDEC_CTLR6 Read/Write 0x00000000 0x0028 Base Address for Differential Motion Vector VDEC_DMVBA Read/Write 0x00000000 0x002C Decoder Control Register 7 VDEC_CTLR7 Read/Write 0x00000000 0x0030 RLC/VLC Data Base Address VDEC_RLCVLCBA Read/Write 0x00000000 0x0034 decoded picture Base Address VDEC_PICTBA Read/Write 0x00000000 0x0038 Reference Picture Index 0 Base Address VDEC_PIDXBA0 Read/Write 0x00000000 0x003C Reference Picture Index 1 Base Address VDEC_PIDXBA1 Read/Write 0x00000000 0x0040 Reference Picture Index 2 Base Address VDEC_PIDXBA2 Read/Write 0x00000000 0x0044 Reference Picture Index 3 Base Address VDEC_PIDXBA3 Read/Write 0x00000000 0x0048 Reference Picture Index 4 Base Address VDEC_PIDXBA4 Read/Write 0x00000000 0x004C Reference Picture Index 5 Base Address VDEC_PIDXBA5 Read/Write 0x00000000 0x0050 Reference Picture Index 6 Base Address VDEC_PIDXBA6 Read/Write 0x00000000 0x0054 Reference Picture Index 7 Base Address VDEC_PIDXBA7 Read/Write 0x00000000 0x0058–0x009C Reserved – – – 0x00A0 Standard Dependent Tables Base Address VDEC_SDTBA Read/Write 0x00000000 0x00A4 Direct Mode Motion Vector Base Address VDEC_DMMVBA Read/Write 0x00000000 0x00A8–0x00BC Reserved – – – 0x00C0 Error Concealment Register VDEC_ECR Read/Write 0x00000000 0x00C4 Reserved – – – 0x00C8 Reserved – – – SAM9M11 [DATASHEET] 1265 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.1 Video Decoder ID Register Name: VDEC_IDR Address: 0x00900000 Access: Read-Only 31 30 29 28 27 26 25 24 PROD_ID 23 22 21 20 19 18 17 16 PROD_ID 15 14 13 12 11 10 9 8 MAJOR_VER MINOR_VER 7 6 5 4 3 2 1 0 MINOR_VER BUILD_VER • BUILD_VER: Build Version Build Version is 0x0. • MINOR_VER: Minor Version Minor Version is 0x88. • MAJOR_VER: Major Version Major Version is 0x0. • PROD_ID: Product ID Product ID is 0x8170. 1266 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.2 Decoder Interrupt Register Name: VDEC_DIR Address: 0x00900004 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – TO JPEGSD ISE 15 14 13 12 11 10 9 8 ASOD SBE BE DR – – – ISET 7 6 5 4 3 2 1 0 – – – ID – – – DE • DE: Decoder Enable 0: Disables Decoder. 1: Enables Decoder. Setting this bit high will start the decoding operation. Hardware will reset this bit when a picture is processed, a stream error or ASO is detected or a bus error is received. • ID: Interrupt Disable 0: Enables Interrupts for decoder. 1: Disables Interrupts for decoder. When high, there will be no interrupts issued by the decoder. Polling must be used to see the hardware status. • ISET: Decoder Interrupt Set 0:Clears the decoder interrupt. Software will reset this after the interrupt is handled. 1: Set the decoder interrupt. This bit drives the interrupt line, OR gated with the post-processor interrupt bit. The interrupt line is not used for the decoder if the interrupt disable bit for decoder is high. • DR: Decoder Ready 0: Decoding in progress. 1: Decoder is ready. When high, the hardware has decoded a picture. Hardware will self-reset. • BE: Bus Error 0: No error. 1: A bus error has occurred. When high, hardware has received an error response from the bus while accessing external memory. This is a fatal error possibly caused by the incorrect allocation of decoder linear memory. Hardware will self-reset. SAM9M11 [DATASHEET] 1267 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• SBE: Stream Buffer Empty 0: Stream Buffer is not empty. 1: Input Stream Buffer is empty but the picture is not ready. Software must provide a new stream pointer to hardware. Hardware will not self-reset. • ASOD: ASO Detected 0: No ASO detected 1: Interrupt status flag ASO detected. Hardware has encountered Arbitrary Slice Order tool in the input H.264 stream data, and software must perform entropy decoding. Hardware will self-reset. • ISE: Input Stream Error 0: No error. 1: Interrupt stream error occurs. When high, hardware has encountered a bit error in the input stream data, and software must perform error concealment. Hardware will self-reset. • JPEGSD: JPEG Slice Decoded 0: No encoding 1: JPEG slice decoded Hardware has decoded the requested amount of macroblock rows of a JPEG picture. When high, the SW must set a new base addresses for the decoder output. Hardware will not self-reset. • TO: Timeout 0: No timeout 1: Timeout occurs When high, decoder has made no bus transactions in 218-1 clock cycles and has not set an interrupt. Possible only if time- out interrupting is enabled. This should be considered as an encountered error in the input stream. Note: Post-processor transactions affect this feature; running stand-alone post-processing while decoding may prevent decoder timeout interrupts. 1268 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.3 Decoder Device Configuration Register Name: VDEC_DDCR Address: 0x00900008 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 HTI – DI_LE – – AHB_BURST DOPF LAT_COMP 15 14 13 12 11 10 9 8 LAT_COMP DDCGE INTCE_LE DO_LE 7 6 5 4 3 2 1 0 PRIOR MAX_BURST_LEN • MAX_BURST_LEN: Maximum Burst Length for Decoder Bus Transactions Valid values for AHB are 0, 1, 4, 8, 16 and 17. 0: INCR transfer type is used always. 1: SINGLE transfer type is used always. 4: INCR4, INCR and SINGLE transfers are allowed. INCR used for 2 and 3 bursts. 8: INCR8, INCR4, INCR and SINGLE transfers are allowed. INCR used for 2 and 3 bursts. 16: INCR16, INCR8, INCR4, INCR and SINGLE transfers are allowed. INCR used for 2 and 3 bursts. 17: INCR16, INCR8, INCR4, INCR and SINGLE transfers are allowed. INCR used for 2, 3, 5, 6, 7, 9, 10, 11, 12, 13, 14 and 15 bursts. • PRIOR: Decoder Core Internal Bus Service Priority 0: Dynamic priority depending on stream content. 1: Post-processor output write has highest priority. 2: Input stream read has highest priority. 3: Reference picture read has highest priority, then post-processor transactions. 4: Reference picture read has highest priority, then decoder output write. • DO_LE: Decoder Output Endian Mode 0: Big endian 1: Little endian • INTCE_LE: Interface Endian Mode 0: Big endian 1: Little endian SAM9M11 [DATASHEET] 1269 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DDCGE: Decoder Dynamic Clock Gating Enable 0: Clock is running for all structures. 1: clock is gated for decoder structures that are not used. Clock gating value should be changed only when the decoder is disabled. • LAT_COMP: Decoder Latency Compensation Decoder latency compensation value in clock cycles. If the best case latency (from bus request to bus grant, or from data request to data receive) is known, the value can be written to these register bits used to compensate the delay. If the latency value is unknown, these bits should be written to zero. Note: Setting the compensation value higher than the best case latency can cause data corruption. • DOPF: Decoder Output Picture Format 0: Output format is raster scan, i.e., pixel rows are written in consecutive memory. 1: Output format is tiled, i.e., macroblocks are written in consecutive memory addresses. • AHB_BURST: AHB Precise Burst and Data Discard Enable 0: INCR bursts of undefined length 2 or 3 may be issued when necessary. 1: Only the precise AHB bursts (SINGLE, INCR4, INCR8 and INCR16) are used in SDRAM read accesses. Extra data is discarded internally. • DI_LE: Decoder Input Endian Mode 0: Big endian 1: Little endian • HTI: Hardware Timeout Interrupt Enable 0: Hardware timeout interrupt disable. 1: Hardware timeout interrupt enable. 1270 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.4 Decoder Control Register 0 (Decoder Mode and Picture Type) Name: VDEC_CTLR0 Address: 0x0090000C Access: Read/Write 31 30 29 28 27 26 25 24 DEC_MODE RLCEN – – – 23 22 21 20 19 18 17 16 PICMODE PICSTRUCT PICBEN PICTYPE PICFIELD FORWMODE – REFFIELD 15 14 13 12 11 10 9 8 OUTDIS FILTDIS QUANT MV REFFIRST – – HLOCK 7 6 5 4 3 2 1 0 – – – – – – – – • HLOCK: HLOCK Enable 0: Locked transfers disabled. 1: Locked transfers enabled. When a locked transfer is granted, bus grant cannot be lost even if a higher priority master requests the bus. • REFFIRST: Reference Field First Indicates which FWD reference field has been decoded first. 0: FWD reference bottom field. 1: FWD reference top field. • MV: MPEG-2 Motion Vector Write Enable Direct mode motion vector write enable / MPEG2 motion vector write enable for error concealment purposes: 0: Writing disabled for current picture. 1: The direct mode motion vectors are written to external memory starting from MV_BASE in direct mode motion vector write/read base address register (offset 0x00a8). • QUANT: Quantization 0: Quantization parameter can vary inside picture. 1: Quantization parameter is fixed (pquant). • FILTDIS: De-block Filtering Disable 0: Filtering is enabled for current picture. 1: Filtering is disabled for current picture. • OUTDIS: Disable Decoder Output Picture Writing 0: Decoder output picture is written to external memory. 1: Decoder output picture is not written to external memory. SAM9M11 [DATASHEET] 1271 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• REFFIELD: Indicates Which Field Should Be Used As Reference Used only if REF_FRAMES =’0’ in Decoder control register 1 (picture parameters). 0: Bottom field 1: Top field • FORWMODE: Coding mode of forward reference picture 0: Progressive 1: Interlaced Note: For backward reference picture the coding mode is always same as for current picture. • PICFIELD: Picture field If field structure is enabled this bit informs which one of the fields is being decoded: 0: Bottom field 1: Top field • PICTYPE: Picture type 0: Intra type (I) 1: Inter type (P) • PICBEN: B Picture Enable B picture enable for current picture: 0: Picture type is I or P depending on PICTYPE. 1: Picture type is BI (vc1)/D (mpeg1) or B depending on PICTYPE. • PICSTRUCT: Structure of the current picture Structure of the current picture (residual structure.) 0: Frame structure, For H.264 this means MBAFF structured picture for interlaced sequence. 1: Field structure • PICMODE: Coding mode of current picture 0: Progressive 1: Interlaced • RLCEN: RLC Mode Enable 0: Decode from input stream (VLC mode). 1: Decode from RLC input data. 1272 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DEC_MODE: Decoding Mode 0: H.264 1: MPEG-4 2: H.263 3: JPEG 4: VC-1 5: MPEG2 6: MPEG1 7: Reserved SAM9M11 [DATASHEET] 1273 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.5 Decoder Control Register 1 (Picture Parameters) Name: VDEC_CTLR1 Address: 0x00900010 Access: Read/Write 31 30 29 28 27 26 25 24 PIC_WIDTH 23 22 21 20 19 18 17 16 PIC_WIDTH WIDTH_OFF PIC_HEIGHT 15 14 13 12 11 10 9 8 PIC_HEIGHT HEIGHT_OFF 7 6 5 4 3 2 1 0 HEIGHT_OFF AVSM TOPF REF_FRAMES • REF_FRAMES: Number of Reference Frames/Semantics H.264: maximum number of short and long term reference frames in decoded picture buffer. VC-1: maximum number of semantics. • TOPF: Top Field Top field is first information for MPEG4 or VC-1. • AVSM: Alternative Vertical Scan Method indicates alternative vertical scan method used for interlaced frames. • HEIGHT_OFF: Height Offset In VC-1 decoding mode only. The amount of meaningful vertical pixels in last macroblock (height offset) 0 if exactly 16 pix- els multiple picture and all the vertical pixels in last macroblock are meaningful. • PIC_HEIGHT: Picture Height Picture height in macroblocks =((height in pixels+15)/16). Picture height is informed as size of the (progressive) frame even though a single field (of interlaced content) is being decoded. • WIDTH_OFF: Width Offset In VC-1 decoding mode only. The amount of meaningful horizontal pixels in last macroblock (width offset) 0 if exactly 16 pixels multiple picture and all the horizontal pixels in last macroblock are meaningful. • PIC_WIDTH: Picture Width Picture width in macroblocks = ((width in pixels + 15) /16). 1274 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.6 Decoder Control Register 2 (MPEG-4/H.263 Stream Decoding Table Selects) Name: VDEC_CTLR2 Address: 0x00900014 Access: Read/Write 31 30 29 28 27 26 25 24 STREAM_START_BIT SYNCMAREN QUANTYPE 23 22 21 20 19 18 17 16 QPFILT_OFF VLC_THR 15 14 13 12 11 10 9 8 VOP_TIME_INC 7 6 5 4 3 2 1 0 VOP_TIME_INC • VOP_TIME_INC: VOP Time Increment VOP time increment resolution. • VLC_THR: VLC Threshold Intra DC VLC threshold. This signal sets QP limits when DC components should be coded separately or like AC components. • QPFILT_OFF: Chrominance Offset Chroma Qp filter offset. • QUANTYPE: Quantization Type Type 1 quantization enable: 0: type 2 inverse Q method. 1: type 1 inverse Q method (Q-tables used). • SYNCMAREN: Synchronization Markers enable 0: Synch markers are not used. 1: Synch markers are used. • STREAM_START_BIT: Stream Start Bit Exact bit of stream start word where decoding can be started. SAM9M11 [DATASHEET] 1275 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.7 Decoder Control Register 3 (Stream Buffer Information) Name: VDEC_CTLR3 Address: 0x00900018 Access: Read/Write 31 30 29 28 27 26 25 24 ST_COD_EN INIT_QP – 23 22 21 20 19 18 17 16 STREAM_LEN 15 14 13 12 11 10 9 8 STREAM_LEN 7 6 5 4 3 2 1 0 STREAM_LEN • STREAM_LEN: Stream Length Amount of stream data bytes in input buffer. If the given buffer size is not enough for finishing the picture, the correspond- ing interrupt is given and new stream buffer base address and stream buffer size information should be given. For VC-1 the buffer must include data for one picture/slice of the picture. For H264/MPEG4/H263/MPEG2/MPEG1 the buffer must include at least data for one slice/VP of the picture. For JPEG the buffer size must be a multiple of 256 bytes or the amount of data for one picture. • INIT_QP: Quantization initialization Initial value for quantization parameter (picture quantizer). • ST_COD_EN: Stream start code Stream start codes exist: 0: Stream does not contain start codes. 1: Stream contains start codes. 1276 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.8 Decoder Control Register 6 (MPEG-4/H.263 Base Address for MB-control) Name: VDEC_CTLR6 Address: 0x00900024 Access: Read/Write 31 30 29 28 27 26 25 24 MB_CONTROL_BASE 23 22 21 20 19 18 17 16 MB_CONTROL_BASE 15 14 13 12 11 10 9 8 MB_CONTROL_BASE 7 6 5 4 3 2 1 0 MB_CONTROL_BASE – – • MB_CONTROL_BASE: Macroblock Control Base Address SAM9M11 [DATASHEET] 1277 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.9 Differential Motion Vector Base Address (H.264, MPEG-4/H.263) Name: VDEC_DMVBA Address: 0x00900028 Access: Read/Write 31 30 29 28 27 26 25 24 MV_CONTROL_BASE 23 22 21 20 19 18 17 16 MV_CONTROL_BASE 15 14 13 12 11 10 9 8 MV_CONTROL_BASE 7 6 5 4 3 2 1 0 MV_CONTROL_BASE • MV_CONTROL_BASE: Differential Motion Vector Base Address 1278 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.10 Decoder Control Register 7 (H264, MPEG-4/H.263) Name: VDEC_CTLR7 Address: 0x0090002C Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address H.264: Intra prediction 4x4 mode base address MPEG-4: DC component base address SAM9M11 [DATASHEET] 1279 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.11 RLC/VLC Data Base Address Name: VDEC_RLCVLCBA Address: 0x00900030 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address RLC_mode: Base address for RLC data (RLCEN = 1 in Decoder Control Register 0). VLC_mode: Stream start address/end address with byte precision (RLCEN = 0 in Decoder Control Register 0) STREAM_START_BIT field in Decoder Control Register 0. When SBE = 1 or DE = 0 in Decoder Interrupt Register, this register contains HW return value of last byte address (not valid for jpeg) where stream has been read (and used) in accu- racy of byte. For debug purposes, the last byte address is also written when stream error/ASO is detected even though it may not be accurate. 1280 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.12 Decoded Picture Base Address (Video, JPEG Decoder Output Luma Picture) Name: VDEC_PICTBA Address: 0x00900034 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Video: Base address for decoder output picture. Points directly to start of decoder output picture or field. SAM9M11 [DATASHEET] 1281 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.13 Reference Picture Index 0 Base Address Name: VDEC_PIDXBA0 Address: 0x00900038 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Video: Base address for reference picture index 0. 1282 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.14 Reference Picture Index 1 Base Address (Video) Name: VDEC_PIDXBA1 Address: 0x0090003C Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for reference picture index 1. SAM9M11 [DATASHEET] 1283 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.15 Reference Picture Index 2 Base Address (Video) Name: VDEC_PIDXBA2 Address: 0x00900040 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for reference picture index 2. 1284 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.16 Reference Picture Index 3 Base Address (Video) Name: VDEC_PIDXBA3 Address: 0x00900044 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for reference picture index 3. SAM9M11 [DATASHEET] 1285 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.17 Reference Picture Index 4 Base Address (MPEG-4/H.263 MVD Control) Name: VDEC_PIDXBA4 Address: 0x00900048 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – SCANF FW_BN 15 14 13 12 11 10 9 8 FW_BN – – – – BW_BN 7 6 5 4 3 2 1 0 BW_BN – – – – ACC_FW RCB ANC • ANC: Anchor Picture Type Previous anchor picture type: 0: intra 1: inter • RCB: Rounding Control Bit When low, 1/2 pixel motion compensation sum is rounded, otherwise clipped. • ACC_FW: Forward Motion Vector Forward motion vector Y resolution: 0: 1/2 accuracy 1: 1/4 accuracy • BW_BN: Backward Bit Number Bit amount for representing backward motion vector for both axes. • FW_BN: Forward Bit Number Bit amount for representing forward motion vector for both axes. • SCANF: Alternate Scan Flag 1286 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.18 Reference Picture Index 5 Base Address (MPEG-4/H.263 TRB/TRD Delta 0) Name: VDEC_PIDXBA5 Address: 0x0090004C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – TRB_PER_TRD 23 22 21 20 19 18 17 16 TRB_PER_TRD 15 14 13 12 11 10 9 8 TRB_PER_TRD 7 6 5 4 3 2 1 0 TRB_PER_TRD • TRB_PER_TRD: TRB per TRD Defines MPEG-4 reference distance syntax TRB/TRD when delta value 0 is used. SAM9M11 [DATASHEET] 1287 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.19 Reference Picture Index 6 Base Address (MPEG-4/H.263 TRB/TRD Delta -1) Name: VDEC_PIDXBA6 Address: 0x00900050 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – TRB_PER_TRD 23 22 21 20 19 18 17 16 TRB_PER_TRD 15 14 13 12 11 10 9 8 TRB_PER_TRD 7 6 5 4 3 2 1 0 TRB_PER_TRD • TRB_PER_TRD: TRB per TRD Defines MPEG-4 reference distance syntax TRB/TRD when delta value -1 is used. 1288 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.20 Reference Picture Index 7 Base Address (MPEG-4/H.263 TRB/TRD Delta 1) Name: VDEC_PIDXBA7 Address: 0x00900054 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – TRB_PER_TRD 23 22 21 20 19 18 17 16 TRB_PER_TRD 15 14 13 12 11 10 9 8 TRB_PER_TRD 7 6 5 4 3 2 1 0 TRB_PER_TRD • TRB_PER_TRD: TRB per TRD Defines MPEG-4 reference distance syntax TRB/TRD when delta value 1 is used. SAM9M11 [DATASHEET] 1289 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.21 Standard Dependent Tables Base Address Name: VDEC_SDTBA Address: 0x009000A0 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for standard dependent tables: 1290 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.22 Direct Mode Motion Vector Base Address Name: VDEC_DMMVBA Address: 0x009000A4 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Not used in JPEG mode. SAM9M11 [DATASHEET] 1291 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.7.23 Error Concealment Register Name: VDEC_ECR Address: 0x009000C0 Access: Read/Write 31 30 29 28 27 26 25 24 STARTMB_X 23 22 21 20 19 18 17 16 STARTMB_X STARTMB_Y 15 14 13 12 11 10 9 8 STARTMB_Y – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – – • STARTMB_Y: Start MB from SW for Y Dimension. Used in error concealment case. Not used in JPEG mode. • STARTMB_X: Start MB from SW for X Dimension. Used in error concealment case. Not used in JPEG mode. 1292 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8 Video Decoder Register Mapping (JPEG) Table 48-12. Video Decoder Register Mapping (JPEG) Offset Register Name Access Reset 0x0000 ID Register VDEC_IDR Read-Only 0x81700880 0x0004 Decoder Interrupt Register VDEC_DIR Read/Write 0x00000000 0x0008 Decoder Device Configuration Register VDEC_DDCR Read/Write 0x00000400 0x000C Decoder Control Register 0 VDEC_CTLR0 Read/Write 0x00000000 0x0010 Decoder Control Register 1 VDEC_CTLR1 Read/Write 0x00000000 0x0014 Decoder Control Register 2 VDEC_CTLR2 Read/Write 0x00000000 0x0018 Decoder Control Register 3 VDEC_CTLR3 Read/Write 0x00000000 0x001C–0x002C Reserved – – – 0x0030 RLC/VLC Data Base Address VDEC_RLCVLCBA Read/Write 0x00000000 0x0034 Decoded Picture Base Address VDEC_PICTBA Read/Write 0x00000000 0x0038 Reference Picture Index 0 Base Address VDEC_PIDXBA0 Read/Write 0x00000000 0x003C Reference Picture Index 1 Base Address VDEC_PIDXBA1 Read/Write 0x00000000 0x0040 Reference Picture Index 2 Base Address VDEC_PIDXBA2 Read/Write 0x00000000 0x0044 Reference Picture Index 3 Base Address VDEC_PIDXBA3 Read/Write 0x00000000 0x0048 Reference Picture Index 4 Base Address VDEC_PIDXBA4 Read/Write 0x00000000 0x004C Reference Picture Index 5 Base Address VDEC_PIDXBA5 Read/Write 0x00000000 0x0050 Reference Picture Index 6 Base Address VDEC_PIDXBA6 Read/Write 0x00000000 0x0054 Reference Picture Index 7 Base Address VDEC_PIDXBA7 Read/Write 0x00000000 0x0058 Reference Picture Index 8 Base Address VDEC_PIDXBA8 Read/Write 0x00000000 0x005C Reference Picture Index 9 Base Address VDEC_PIDXBA9 Read/Write 0x00000000 0x0060 Reference Picture Index 10 Base Address VDEC_PIDXBA10 Read/Write 0x00000000 0x0064 Reference Picture Index 11 Base Address VDEC_PIDXBA11 Read/Write 0x00000000 0x0068 Reference Picture Index 12 Base Address VDEC_PIDXBA12 Read/Write 0x00000000 0x006C Reference Picture Index 13 Base Address VDEC_PIDXBA13 Read/Write 0x00000000 0x0070–0x009C Reserved – – – 0x00A0 Standard Dependent Tables Base Address VDEC_SDTBA Read/Write 0x00000000 0x00A4–0x00C4 Reserved – – – 0x00C8 Reserved – – – SAM9M11 [DATASHEET] 1293 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.1 Video Decoder ID Register Name: VDEC_IDR Address: 0x00900000 Access: Read-Only 31 30 29 28 27 26 25 24 PROD_ID 23 22 21 20 19 18 17 16 PROD_ID 15 14 13 12 11 10 9 8 MAJOR_VER MINOR_VER 7 6 5 4 3 2 1 0 MINOR_VER BUILD_VER • BUILD_VER: Build Version Build Version is 0x0 • MINOR_VER: Minor Version Minor Version is 0x88. • MAJOR_VER: Major Version Major Version is 0x0. • PROD_ID: Product ID Product ID is 0x8170. 1294 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.2 Decoder Interrupt Register Name: VDEC_DIR Address: 0x00900004 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – TO JPEGSD ISE 15 14 13 12 11 10 9 8 ASOD SBE BE DR – – – ISET 7 6 5 4 3 2 1 0 – – – ID – – – DE • DE: Decoder Enable 0: Disables decoder. 1: Enables decoder. Setting this bit high will start the decoding operation. Hardware will reset this bit when a picture is processed, a stream error or ASO is detected or a bus error is received. • ID: Interrupt Disable 0: Enables interrupts for decoder. 1: Disables interrupts for decoder. When high, there will be no interrupts issued by the decoder. Polling must be used to see the hardware status. • ISET: Decoder Interrupt Set 0: Clears the decoder interrupt. Software will reset this after the interrupt is handled. 1: Sets the decoder interrupt. This bit drives the interrupt line, OR gated with the post-processor interrupt bit. The interrupt line is not used for the decoder if the interrupt disable bit for decoder is high. • DR: Decoder Ready 0: Decoding in progress. 1: Decoder is ready. When high, the hardware has decoded a picture. Hardware will self-reset. • BE: Bus Error 0: No error. 1: A bus error has occurred. When high, hardware has received an error response from the bus while accessing external memory. This is a fatal error possibly caused by the incorrect allocation of decoder linear memory. Hardware will self-reset. SAM9M11 [DATASHEET] 1295 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• SBE: Stream Buffer Empty 0: Stream Buffer is not empty. 1: Input Stream Buffer is empty but the picture is not ready. Software must provide a new stream pointer to hardware. Hardware will not self-reset. • ASOD: ASO Detected 0: No ASO detected. 1: Interrupt status flag ASO detected. Hardware has encountered Arbitrary Slice Order tool in the input H.264 stream data, and software must perform entropy decoding. Hardware will self-reset. • ISE: Input Stream Error 0: No Error. 1: Interrupt Stream Error occurs. When high, hardware has encountered a bit error in the input stream data, and software must perform error concealment. Hardware will self-reset. • JPEGSD: JPEG slice Decoded 0: No Decoding. 1: JPEG slice decoded. Hardware has decoded the requested amount of macroblock rows of a JPEG picture. When high, the SW must set a new base addresses for the decoder output. Hardware will not self-reset. • TO: Timeout 0: No Timeout 1: Timeout occurs When high, decoder has made no bus transactions in 218-1 clock cycles and has not set an interrupt. Possible only if time- out interrupting is enabled. This should be considered as an encountered error in the input stream. Note: Post-processor transactions affect this feature; running stand-alone post-processing while decoding may prevent decoder timeout interrupts. 1296 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.3 Decoder Device Configuration Register Name: VDEC_DDCR Address: 0x00900008 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 HTI – DI_LE – – AHB_BURST DOPF LAT_COMP 15 14 13 12 11 10 9 8 LAT_COMP DDCGE INTCE_LE DO_LE 7 6 5 4 3 2 1 0 PRIOR MAX_BURST_LEN • MAX_BURST_LEN: Maximum burst length for decoder bus transactions Valid values for AHB are 0, 1, 4, 8, 16 and 17. 0: INCR transfer type is used always 1: SINGLE transfer type is used always 4: INCR4, INCR and SINGLE transfers are allowed. INCR used for 2 and 3 bursts. 8: INCR8, INCR4, INCR and SINGLE transfers are allowed. INCR used for 2 and 3 bursts. 16: INCR16, INCR8, INCR4, INCR and SINGLE transfers are allowed. INCR used for 2 and 3 bursts. 17: INCR16, INCR8, INCR4, INCR and SINGLE transfers are allowed. INCR used for 2, 3, 5, 6, 7, 9, 10, 11, 12, 13, 14 and 15 bursts. • PRIOR: Decoder core internal bus service priority 0: Dynamic priority depending on stream content. 1: Post-processor output write has highest priority. 2: Input stream read has highest priority. 3: Reference picture read has highest priority, then post-processor transactions. 4: Reference picture read has highest priority, then decoder output write. • DO_LE: Decoder Output Endian Mode 0: Big endian 1: Little endian • INTCE_LE: Interface Endian Mode 0: Big endian 1: Little endian SAM9M11 [DATASHEET] 1297 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DDCGE: Decoder Dynamic Clock Gating Enable 0: Clock is running for all structures. 1: Clock is gated for decoder structures that are not used. Clock gating value should be changed only when the decoder is disabled. • LAT_COMP: Decoder Latency Compensation Decoder latency compensation value in clock cycles. If the best case latency (from bus request to bus grant, or from data request to data receive) is known, the value can be written to these register bits used to compensate the delay. If the latency value is unknown, these bits should be written to zero. Note: Setting the compensation value higher than the best case latency can cause data corruption. • DOPF: Decoder Output Picture Format 0: Output format is raster scan, i.e., pixel rows are written in consecutive memory. 1: Output format is tiled, i.e., macroblocks are written in consecutive memory addresses. • AHB_BURST: AHB precise burst and data discard enable 0: INCR bursts of undefined length 2 or 3 may be issued when necessary. 1: Only the precise AHB bursts (SINGLE, INCR4, INCR8 and INCR16) are used in SDRAM read accesses. Extra data is discarded internally. • DI_LE: Decoder Input Endian Mode 0: Big endian 1: Little endian • HTI: Hardware Timeout Interrupt Enable 0: Hardware Timeout Interrupt Disable 1: Hardware Timeout Interrupt Enable 1298 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.4 Decoder Control Register 0 (Decoder Mode and Picture Type) Name: VDEC_CTLR0 Address: 0x0090000C Access: Read/Write 31 30 29 28 27 26 25 24 DEC_MODE RLCEN – – – 23 22 21 20 19 18 17 16 PICMODE PICSTRUCT PICBEN PICTYPE PICFIELD FORWMODE – REFFIELD 15 14 13 12 11 10 9 8 OUTDIS FILTDIS QUANT MV REFFIRST – – HLOCK 7 6 5 4 3 2 1 0 – – – – – – – – • HLOCK: HLOCK Enable 0: Locked transfers disabled. 1: Locked transfers enabled. When a locked transfer is granted, bus grant cannot be lost even if a higher priority master requests the bus. • REFFIRST: Reference Field First Indicates which FWD reference field has been decoded first. 0: FWD reference bottom field. 1: FWD reference top field. • MV: MPEG-2 Motion Vector Write Enable Direct mode motion vector write enable / MPEG2 motion vector write enable for error concealment purposes: 0: Writing disabled for current picture. 1: The direct mode motion vectors are written to external memory starting from MV_BASE in Direct mode motion vector write/read base address register (offset 0x00a8). • QUANT: Quantization 0: Quantization parameter can vary inside picture. 1: Quantization parameter is fixed (pquant). • FILTDIS: De-block Filtering Disable 0: Filtering is enabled for current picture. 1: Filtering is disabled for current picture. • OUTDIS: Disable Decoder Output Picture Writing 0: Decoder output picture is written to external memory 1: Decoder output picture is not written to external memory SAM9M11 [DATASHEET] 1299 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• REFFIELD: Indicates Which Field Should Be Used As Reference Used only if REF_FRAMES =’0’ in Decoder control register 1 (picture parameters). 0: Bottom field 1: Top field • FORWMODE: Coding Mode of Forward Reference Picture 0: Progressive 1: Interlaced Note: For backward reference picture the coding mode is always the same as for current picture. • PICFIELD: Picture Field If field structure is enabled this bit informs which one of the fields is being decoded: 0: Bottom field 1: Top field • PICTYPE: Picture Type 0: Intra type (I) 1: Inter type (P) • PICBEN: B Picture Enable B picture enable for current picture: 0: Picture type is I or P depending on PICTYPE. 1: Picture type is BI (vc1)/D (mpeg1) or B depending on PICTYPE. • PICSTRUCT: Structure of the Current Picture Structure of the current picture (residual structure). 0: Frame structure. For H.264 this means MBAFF structured picture for interlaced sequence. 1: Field structure • PICMODE: Coding mode of CURRENT PICTure 0: Progressive 1: Interlaced • RLCEN: RLC Mode Enable 0: Decode from input stream (VLC mode). 1: Decode from RLC input data. 1300 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DEC_MODE: Decoding Mode 0: H.264 1: MPEG-4 2: H.263 3: JPEG 4: VC-1 5: MPEG2 6: MPEG1 7: Reserved SAM9M11 [DATASHEET] 1301 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.5 Decoder Control Register 1 (Picture Parameters) Name: VDEC_CTLR1 Address: 0x00900010 Access: Read/Write 31 30 29 28 27 26 25 24 PIC_WIDTH 23 22 21 20 19 18 17 16 PIC_WIDTH WIDTH_OFF PIC_HEIGHT 15 14 13 12 11 10 9 8 PIC_HEIGHT HEIGHT_OFF 7 6 5 4 3 2 1 0 HEIGHT_OFF AVSM TOPF REF_FRAMES • REF_FRAMES: Number of reference frames/semantics H.264: maximum number of short and long term reference frames in decoded picture buffer. VC-1: maximum number of semantics. • TOPF: Top Field Top field is first information for MPEG4 or VC-1. • AVSM: Alternative Vertical Scan Method indicates alternative vertical scan method used for interlaced frames • HEIGHT_OFF: Height Offset In VC-1 decoding mode only. The amount of meaningful vertical pixels in last macroblock (height offset) 0 if exactly 16 pix- els multiple picture and all the vertical pixels in last macroblock are meaningful. • PIC_HEIGHT: Picture Height Picture height in macroblocks =((height in pixels+15)/16). Picture height is informed as size of the (progressive) frame even though a single field (of interlaced content) is being decoded. • WIDTH_OFF: Width Offset In VC-1 decoding mode only. The amount of meaningful horizontal pixels in last macroblock (width offset) 0 if exactly 16 pixels multiple picture and all the horizontal pixels in last macroblock are meaningful. • PIC_WIDTH: Picture Width Picture width in macroblocks = ((width in pixels + 15) /16). 1302 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.6 Decoder Control Register 2 (JPEG Stream Decoding Table Selects) Name: VDEC_CTLR2 Address: 0x00900014 Access: Read/Write 31 30 29 28 27 26 25 24 STREAM_START_BIT – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – QTABLE MODE 7 6 5 4 3 2 1 0 FILL END ACCR ACCB DCCR DCCB – – • DCCB: DC Component of the Cb Defines which VLC table should be used for decoding DC components of the Cb. 0: First 1: Second Note: For luminance the first table is always used • DCCR: DC Component of the Cr Defines which VLC table should be used for decoding DC components of the Cr. 0: First 1: Second Note: For luminance the first table is always used. • ACCB: AC Component of the Cb Defines which VLC table should be used for decoding AC components of the Cb. 0: First 1: Second Note: For luminance the first table is always used. • ACCR: AC Component of the Cr Defines which VLC table should be used for decoding AC components of the Cr. 0: First 1: Second Note: For luminance the first table is always used. SAM9M11 [DATASHEET] 1303 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• END: End of JPEG Image in the Stream 0: Current stream buffer does not contain the end of a JPEG image. HW will not flush the stream data pipeline after a buffer empty request. 1: Current stream buffer contains the end of a JPEG image. HW will flush data pipeline and will not request more stream providing it finds the EOI pattern at the end. • FILL: JPEG Fill Right 0: JPEG picture width is a multiple of 16. 1: JPEG picture width is a multiple of 8 pixels but not a multiple of 16 pixels. Can be set to 1 only for JPEG sampling format 0. HW must fill one block of zero pixel data to the right border of the picture. • MODE: JPEG Mode Input picture sampling format 0: single type, MB 1 block, 1: single type, MB 4 blocks (not supported), 2: three types, MB 6 blocks (4:2:0), 3: three types, MB 4 blocks (4:2:2), 4: three types, MB 3 blocks (4:4:4) (Not supported) 5: three types, MB 4 blocks (4:4:0) • QTABLES: Amount of Quantization Tables in External Memory 0: No quantization tables. (not supported) 1: One quantization table. Used when picture is single type. 2: Two quantization tables. One for luminance and one for Chrominance. (not supported) 3: Three quantization tables. Each type (Lu, Cr, Cb) has own QP-table. Base address for tables is defined in “Base address for standard dependent tables” register, offset 0x00a0. • STREAM_START_BIT: Stream Start Bit Exact bit of stream start word where decoding can be started. 1304 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.7 Decoder Control Register 3 (Stream Buffer Information) Name: VDEC_CTLR3 Address: 0x00900018 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 STREAM_LEN 15 14 13 12 11 10 9 8 STREAM_LEN 7 6 5 4 3 2 1 0 STREAM_LEN • STREAM_LEN: Stream Length Amount of stream data bytes in input buffer. If the given buffer size is not enough for finishing the picture, the correspond- ing interrupt is given and new stream buffer base address and stream buffer size information should be given. The buffer size must be a multiple of 256 bytes or the amount of data for one picture. SAM9M11 [DATASHEET] 1305 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.8 RLC/VLC Data Base Address Name: VDEC_RLCVLCBA Address: 0x00900030 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address RLC_mode: Base address for RLC data (RLCEN = 1 in Decoder Control Register 0). VLC_mode: Stream start address/end address with byte precision (RLCEN = 0 in Decoder Control Register 0) STREAM_START_BIT field in Decoder Control Register 0. When SBE = 1 or DE = 0 in Decoder Interrupt Register, this register contains HW return value of last byte address (not valid for jpeg) where stream has been read (and used) in accu- racy of byte. For debug purposes, the last byte address is also written when stream error/ASO is detected even though it may not be accurate. 1306 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.9 Decoded Picture Base Address (JPEG Decoder Output Luma Picture) Name: VDEC_PICTBA Address: 0x00900034 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for decoder output luminance picture. SAM9M11 [DATASHEET] 1307 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.10 Reference Picture Index 0 Base Address (JPEG Decoder Output Chroma Picture) Name: VDEC_PIDXBA0 Address: 0x00900038 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address JPEG: Base address for decoder output chrominance picture (not needed if decoder output is not written). 1308 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.11 Reference Picture Index 1 Base Address (JPEG Control) Name: VDEC_PIDXBA1 Address: 0x0090003C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 JPEG_SLICE • JPEG_SLICE: Base Address Height of the slice (multiple of 16 pixels) that HW decodes before interrupt. When slice is decoded, HW will raise an inter- rupt and reset external addresses back to base address. Note, value 0 disables JPEG slice mode. SAM9M11 [DATASHEET] 1309 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.12 Reference Picture Index 2 Base Address (JPEG VLC Code Length First AC Table) Name: VDEC_PIDXBA2 Address: 0x00900040 Access: Read/Write 31 30 29 28 27 26 25 24 – AC1_CODE6 23 22 21 20 19 18 17 16 – – AC1_CODE5 15 14 13 12 11 10 9 8 AC1_CODE4 AC1_CODE3 7 6 5 4 3 2 1 0 AC1_CODE3 – AC1_CODE2 – AC1_CODE1 • AC1_CODEx: Amount of Code Words of Length x 1310 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.13 Reference Picture Index 3 Base Address (JPEG VLC Code length First AC Table) Name: VDEC_PIDXBA3 Address: 0x00900044 Access: Read/Write 31 30 29 28 27 26 25 24 AC1_CODE10 23 22 21 20 19 18 17 16 AC1_CODE9 15 14 13 12 11 10 9 8 AC1_CODE8 7 6 5 4 3 2 1 0 AC1_CODE7 • AC1_CODEx: Amount of Code Words of Length x SAM9M11 [DATASHEET] 1311 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.14 Reference Picture Index 4 Base Address (JPEG VLC Code Length First ACTable) Name: VDEC_PIDXBA4 Address: 0x00900048 Access: Read/Write 31 30 29 28 27 26 25 24 AC1_CODE14 23 22 21 20 19 18 17 16 AC1_CODE13 15 14 13 12 11 10 9 8 AC1_CODE12 7 6 5 4 3 2 1 0 AC1_CODE11 • AC1_CODEx: Amount of Code Words of Length x 1312 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.15 Reference Picture Index 5 Base Address (JPEG VLC Code Length First/Second AC Table) Name: VDEC_PIDXBA5 Address: 0x0090004C Access: Read/Write 31 30 29 28 27 26 25 24 AC2_CODE4 AC2_CODE3 23 22 21 20 19 18 17 16 AC2_CODE3 – AC2_CODE2 – AC2_CODE1 15 14 13 12 11 10 9 8 AC1_CODE16 7 6 5 4 3 2 1 0 AC1_CODE15 • AC1_CODEx: Amount of Code Words of Length x (first table) • AC2_CODEy: Amount of Code Words of Length y (second table) SAM9M11 [DATASHEET] 1313 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.16 Reference Picture Index 6 Base Address (JPEG VLC Code Length Second AC Table) Name: VDEC_PIDXBA6 Address: 0x00900050 Access: Read/Write 31 30 29 28 27 26 25 24 AC2_CODE8 23 22 21 20 19 18 17 16 AC2_CODE7 15 14 13 12 11 10 9 8 – AC2_CODE6 7 6 5 4 3 2 1 0 – – AC2_CODE5 • AC2_CODEy: Amount of Code Words of Length y 1314 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.17 Reference Picture Index 7 Base Address (JPEG VLC Code Length Second AC Table) Name: VDEC_PIDXBA7 Address: 0x00900054 Access: Read/Write 31 30 29 28 27 26 25 24 AC2_CODE12 23 22 21 20 19 18 17 16 AC2_CODE11 15 14 13 12 11 10 9 8 AC2_CODE10 7 6 5 4 3 2 1 0 AC2_CODE9 • AC2_CODEy: Amount of Code Words of Length y SAM9M11 [DATASHEET] 1315 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.18 Reference Picture Index 8 Base Address (JPEG VLC Code Length Second AC Table) Name: VDEC_PIDXBA8 Address: 0x00900058 Access: Read/Write 31 30 29 28 27 26 25 24 AC2_CODE16 23 22 21 20 19 18 17 16 AC2_CODE15 15 14 13 12 11 10 9 8 AC2_CODE14 7 6 5 4 3 2 1 0 AC2_CODE13 • AC2_CODEy: Amount of Code Words of Length y 1316 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.19 Reference Picture Index 9 Base Address (JPEG VLC Code Length First DC Table) Name: VDEC_PIDXBA9 Address: 0x0090005C Access: Read/Write 31 30 29 28 27 26 25 24 DC1_CODE8 DC1_CODE7 23 22 21 20 19 18 17 16 DC1_CODE6 DC1_CODE5 15 14 13 12 11 10 9 8 DC1_CODE4 DC1_CODE3 7 6 5 4 3 2 1 0 – DC1_CODE2 – – DC1_CODE1 • DC1_CODEx: Amount of Code Words of Length x SAM9M11 [DATASHEET] 1317 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.20 Reference Picture Index 10 Base Address (JPEG VLC Code Length First DC Table) Name: VDEC_PIDXBA10 Address: 0x00900060 Access: Read/Write 31 30 29 28 27 26 25 24 DC1_CODE16 DC1_CODE15 23 22 21 20 19 18 17 16 DC1_CODE14 DC1_CODE13 15 14 13 12 11 10 9 8 DC1_CODE12 DC1_CODE11 7 6 5 4 3 2 1 0 DC1_CODE10 DC1_CODE9 • DC1_CODEx: Amount of Code Words of Length x 1318 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.21 Reference Picture Index 11 Base Address (JPEG VLC Code Length Second DC Table) Name: VDEC_PIDXBA11 Address: 0x00900064 Access: Read/Write 31 30 29 28 27 26 25 24 DC2_CODE8 DC2_CODE7 23 22 21 20 19 18 17 16 DC2_CODE6 DC2_CODE5 15 14 13 12 11 10 9 8 DC2_CODE4 DC2_CODE3 7 6 5 4 3 2 1 0 – DC2_CODE2 – – DC2_CODE1 • DC2_CODEy: Amount of Code Words of Length y SAM9M11 [DATASHEET] 1319 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.22 Reference Picture Index 12 Base Address (JPEG VLC Code Length Second DC Table) Name: VDEC_PIDXBA12 Address: 0x00900068 Access: Read/Write 31 30 29 28 27 26 25 24 DC2_CODE16 DC2_CODE15 23 22 21 20 19 18 17 16 DC2_CODE14 DC2_CODE13 15 14 13 12 11 10 9 8 DC2_CODE12 DC2_CODE11 7 6 5 4 3 2 1 0 DC2_CODE10 DC2_CODE9 • DC2_CODEy: Amount of Code Words of Length y 1320 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.8.23 Standard Dependent Tables Base Address Name: VDEC_SDTBA Address: 0x009000A0 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for standard dependent tables: SAM9M11 [DATASHEET] 1321 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9 Video Decoder Register Mapping (VC-1) Table 48-13. Video Decoder Register Mapping (VC1) Offset Register Name Access Reset 0x0000 ID Register VDEC_IDR Read-Only 0x81700880 0x0004 Decoder Interrupt Register VDEC_DIR Read/Write 0x00000000 0x0008 Decoder Device Configuration Register VDEC_DDCR Read/Write 0x00000400 0x000C Decoder Control Register 0 VDEC_CTLR0 Read/Write 0x00000000 0x0010 Decoder Control Register 1 VDEC_CTLR1 Read/Write 0x00000000 0x0014 Decoder Control Register 2 VDEC_CTLR2 Read/Write 0x00000000 0x0018 Decoder Control Register 3 VDEC_CTLR3 Read/Write 0x00000000 0x001C Decoder Control Register 4 VDEC_CTLR4 Read/Write 0x00000000 0x0020 Decoder Control Register 5 VDEC_CTLR5 Read/Write 0x00000000 0x0024 Decoder Control Register 6 VDEC_CTLR6 Read/Write 0x00000000 0x0028 Base Address for Differential Motion Vector VDEC_DMVBA Read/Write 0x00000000 0x002C Decoder Control Register 7 VDEC_CTLR7 Read/Write 0x00000000 0x0030 RLC/VLC Data Base Address VDEC_RLCVLCBA Read/Write 0x00000000 0x0034 Decoded Picture Base Address VDEC_PICTBA Read/Write 0x00000000 0x0038 Reference Picture Index 0 Base Address VDEC_PIDXBA0 Read/Write 0x00000000 0x003C Reference Picture Index 1 Base Address VDEC_PIDXBA1 Read/Write 0x00000000 0x0040 Reference Picture Index 2 Base Address VDEC_PIDXBA2 Read/Write 0x00000000 0x0044 Reference Picture Index 3 Base Address VDEC_PIDXBA3 Read/Write 0x00000000 0x0048 Reference Picture Index 4 Base Address VDEC_PIDXBA4 Read/Write 0x00000000 0x004C Reference Picture Index 5 Base Address VDEC_PIDXBA5 Read/Write 0x00000000 0x0050 Reference Picture Index 6 Base Address VDEC_PIDXBA6 Read/Write 0x00000000 0x0054–0x0068 Reserved – – – 0x006C Reference Picture Index 13 Base Address VDEC_PIDXBA13 Read/Write 0x00000000 0x0070–0x00A0 Reserved – – – 0x00A4 Direct Mode Motion Vector Base Address VDEC_DMMVBA Read/Write 0x00000000 0x00A8–0x00BC Reserved – – – 0x00C0 Error Concealment Register VDEC_ECR Read/Write 0x00000000 0x00C4 Reserved – – – 0x00C8 Reserved – – – 1322 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.1 Video Decoder ID Register Name: VDEC_IDR Address: 0x00900000 Access: Read-Only 31 30 29 28 27 26 25 24 PROD_ID 23 22 21 20 19 18 17 16 PROD_ID 15 14 13 12 11 10 9 8 MAJOR_VER MINOR_VER 7 6 5 4 3 2 1 0 MINOR_VER BUILD_VER • BUILD_VER: Build Version Build Version is 0x0. • MINOR_VER: Minor Version Minor Version is 0x88. • MAJOR_VER: Major Version Major Version is 0x0. • PROD_ID: Product ID Product ID is 0x8170. SAM9M11 [DATASHEET] 1323 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.2 Decoder Interrupt Register Name: VDEC_DIR Address: 0x00900004 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – TO JPEGSD ISE 15 14 13 12 11 10 9 8 ASOD SBE BE DR – – – ISET 7 6 5 4 3 2 1 0 – – – ID – – – DE • DE: Decoder Enable 0: Disables decoder. 1: Enables decoder. Setting this bit high will start the decoding operation. Hardware will reset this bit when a picture is processed, a stream error or ASO is detected or a bus error is received. • ID: Interrupt Disable 0: Enables interrupts for decoder. 1: Disables interrupts for decoder. When high, there will be no interrupts issued by the decoder. Polling must be used to see the hardware status. • ISET: Decoder Interrupt Set 0: Clears the decoder interrupt. Software will reset this after the interrupt is handled. 1: Set the decoder interrupt. This bit drives the interrupt line, OR gated with the post-processor interrupt bit. The interrupt line is not used for the decoder if the interrupt disable bit for decoder is high. • DR: Decoder Ready 0: Decoding in progress. 1: Decoder is ready. When high, the hardware has decoded a picture. Hardware will self-reset. • BE: Bus Error 0: No error. 1: A bus error has occurred. When high, hardware has received an error response from the bus while accessing external memory. This is a fatal error possibly caused by the incorrect allocation of decoder linear memory. Hardware will self-reset. 1324 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• SBE: Stream Buffer Empty 0: Stream Buffer is not empty 1: Input Stream Buffer is empty but the picture is not ready. Software must provide a new stream pointer to hardware. Hardware will not self-reset. • ASOD: ASO Detected 0: No ASO detected. 1: Interrupt status flag ASO detected. Hardware has encountered Arbitrary Slice Order tool in the input H.264 stream data, and software must perform entropy decoding. Hardware will self-reset. • ISE: Input Stream Error 0: No error. 1: Interrupt stream error occurs. When high, hardware has encountered a bit error in the input stream data, and software must perform error concealment. Hardware will self-reset. • JPEGSD: JPEG Slice Decoded 0: No decoding. 1: JPEG slice decoded. Hardware has decoded the requested amount of macroblock rows of a JPEG picture. When high, the SW must set a new base address for the decoder output. Hardware will not self-reset. • TO: Timeout 0: No timeout. 1: Timeout occurs. When high, decoder has made no bus transactions in 218-1 clock cycles and has not set an interrupt. Possible only if time- out interrupting is enabled. This should be considered as an encountered error in the input stream. Note: Post-processor transactions affect this feature; running stand-alone post-processing while decoding may prevent decoder timeout interrupts. SAM9M11 [DATASHEET] 1325 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.3 Decoder Device Configuration Register Name: VDEC_DDCR Address: 0x00900008 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 HTI – DI_LE – – AHB_BURST DOPF LAT_COMP 15 14 13 12 11 10 9 8 LAT_COMP DDCGE INTCE_LE DO_LE 7 6 5 4 3 2 1 0 PRIOR MAX_BURST_LEN • MAX_BURST_LEN: Maximum Burst Length for Decoder Bus Transactions Valid values for AHB are 0, 1, 4, 8, 16 and 17. 0: INCR transfer type is used always. 1: SINGLE transfer type is used always. 4: INCR4, INCR and SINGLE transfers are allowed. INCR used for 2 and 3 bursts. 8: INCR8, INCR4, INCR and SINGLE transfers are allowed. INCR used for 2 and 3 bursts. 16: INCR16, INCR8, INCR4, INCR and SINGLE transfers are allowed. INCR used for 2 and 3 bursts. 17: INCR16, INCR8, INCR4, INCR and SINGLE transfers are allowed. INCR used for 2, 3, 5, 6, 7, 9, 10, 11, 12, 13, 14 and 15 bursts. • PRIOR: Decoder Core Internal Bus Service Priority 0: Dynamic priority depending on stream content. 1: Post-processor output write has highest priority. 2: Input stream read has highest priority. 3: Reference picture read has highest priority, then post-processor transactions. 4: Reference picture read has highest priority, then decoder output write. • DO_LE: Decoder Output Endian Mode 0: Big endian 1: Little endian • INTCE_LE: Interface Endian Mode 0: Big endian 1: Little endian 1326 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DDCGE: Decoder Dynamic Clock Gating Enable 0: Clock is running for all structures. 1: Clock is gated for decoder structures that are not used. Clock gating value should be changed only when the decoder is disabled. • LAT_COMP: Decoder Latency Compensation Decoder latency compensation value in clock cycles. If the best case latency (from bus request to bus grant, or from data request to data receive) is known, the value can be written to these register bits used to compensate the delay. If the latency value is unknown, these bits should be written to zero. Note: Setting the compensation value higher than the best case latency can cause data corruption. • DOPF: Decoder Output Picture Format 0: Output format is raster scan, i.e., pixel rows are written in consecutive memory. 1: Output format is tiled, i.e., macroblocks are written in consecutive memory addresses. • AHB_BURST: AHB Precise Burst and Data Discard Enable 0: INCR bursts of undefined length 2 or 3 may be issued when necessary. 1: Only the precise AHB bursts (SINGLE, INCR4, INCR8 and INCR16) are used in SDRAM read accesses. Extra data is discarded internally. • DI_LE: Decoder Input Endian Mode 0: Big endian 1: Little endian • HTI: Hardware Timeout Interrupt Enable 0: Hardware Timeout Interrupt Disable 1: Hardware Timeout Interrupt Enable SAM9M11 [DATASHEET] 1327 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.4 Decoder Control Register 0 (Decoder Mode and Picture Type) Name: VDEC_CTLR0 Address: 0x0090000C Access: Read/Write 31 30 29 28 27 26 25 24 DEC_MODE RLCEN – – – 23 22 21 20 19 18 17 16 PICMODE PICSTRUCT PICBEN PICTYPE PICFIELD FORWMODE – REFFIELD 15 14 13 12 11 10 9 8 OUTDIS FILTDIS QUANT MV REFFIRST – – HLOCK 7 6 5 4 3 2 1 0 – – – – – – – – • HLOCK: HLOCK Enable 0: Locked transfers disabled. 1: Locked transfers enabled. When a locked transfer is granted, bus grant cannot be lost even if a higher priority master requests the bus. • REFFIRST: Reference Field First Indicates which FWD reference field has been decoded first. 0: FWD reference bottom field. 1: FWD reference top field. • MV: MPEG-2 motion vector write enable Direct mode motion vector write enable/MPEG2 motion vector write enable for error concealment purposes: 0: Writing disabled for current picture. 1:The direct mode motion vectors are written to external memory starting from MV_BASE in Direct mode motion vector write/read base address register (offset 0x00a8). • QUANT: Quantization 0: Quantization parameter can vary inside picture. 1: Quantization parameter is fixed (pquant). • FILTDIS: De-block filtering disable 0: Filtering is enabled for current picture. 1: Filtering is disabled for current picture • OUTDIS: Disable decoder output picture writing 0: Decoder output picture is written to external memory 1: Decoder output picture is not written to external memory 1328 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• REFFIELD: Indicates Which Field Should Be Used As Reference Used only if REF_FRAMES =’0’ in Decoder control register 1 (picture parameters) 0: Bottom field 1: Top field • FORWMODE: Coding Mode of Forward Reference Picture 0: Progressive 1: Interlaced Note: For backward reference picture the coding mode is always same as for current picture. • PICFIELD: Picture Field If field structure is enabled this bit informs which one of the fields is being decoded: 0: Bottom field 1: Top field • PICTYPE: Picture Type 0: Intra type (I) 1: Inter type (P) • PICBEN: B Picture Enable B picture enable for current picture: 0: Picture type is I or P depending on PICTYPE. 1: Picture type is BI (vc1)/D (mpeg1) or B depending on PICTYPE. • PICSTRUCT: Structure of The Current Picture Structure of the current picture (residual structure) 0: Frame structure, For H.264 this means MBAFF structured picture for interlaced sequence. 1: Field structure. • PICMODE: Coding Mode of Current Picture 0: Progressive 1: Interlaced • RLCEN: RLC Mode Enable 0: Decode from input stream (VLC mode). 1: Decode from RLC input data. SAM9M11 [DATASHEET] 1329 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DEC_MODE: Decoding Mode 0: H.264 1: MPEG-4 2: H.263 3: JPEG 4: VC-1 5: MPEG2 6: MPEG1 7: Reserved 1330 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.5 Decoder Control Register 1 (Picture Parameters) Name: VDEC_CTLR1 Address: 0x00900010 Access: Read/Write 31 30 29 28 27 26 25 24 PIC_WIDTH 23 22 21 20 19 18 17 16 PIC_WIDTH WIDTH_OFF PIC_HEIGHT 15 14 13 12 11 10 9 8 PIC_HEIGHT HEIGHT_OFF 7 6 5 4 3 2 1 0 HEIGHT_OFF AVSM TOPF REF_FRAMES • REF_FRAMES: Number of Reference Frames/Semantics VC-1: maximum number of semantics. • TOPF: Top Field Top field is first information for VC-1. • AVSM: Alternative Vertical Scan Method Indicates alternative vertical scan method used for interlaced frames. • HEIGHT_OFF: Height Offset The amount of meaningful vertical pixels in last macroblock (height offset) 0 if exactly 16 pixels multiple picture and all the vertical pixels in last macroblock are meaningful. • PIC_HEIGHT: Picture Height Picture height in macroblocks = ((height in pixels+15)/16). Picture height is informed as size of the (progressive) frame even though a single field (of interlaced content) is being decoded. • WIDTH_OFF: Width Offset The amount of meaningful horizontal pixels in last macroblock (width offset) 0 if exactly 16 pixels multiple picture and all the horizontal pixels in last macroblock are meaningful. • PIC_WIDTH: Picture Width Picture width in macroblocks = ((width in pixels + 15) /16). SAM9M11 [DATASHEET] 1331 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.6 Decoder Control Register 2 (VC-1 Stream Decoding Table Selects) Name: VDEC_CTLR2 Address: 0x00900014 Access: Read/Write 31 30 29 28 27 26 25 24 STREAM_START_BIT SYNCMAREN Q_PROFILE 23 22 21 20 19 18 17 16 DQBI IS_REDU – FAST_UVMC – – TDC_TAB CAC_TAB 15 14 13 12 11 10 9 8 CAC_TAB YAC_TAB MB_MODE_TAB MV_TAB 7 6 5 4 3 2 1 0 MV_TAB MB_TAB 2MV_TAB 4MV_TAB • 4MV_TAB: 4MV Block Pattern Block pattern table select in interlaced pictures when 4mv macroblock. • 2MV_TAB: 2MV Block Pattern Block pattern table select in interlaced pictures when 2mv macroblock. • MB_TAB: MB Table Selection In MB layer specifies which of four tables is used to decode the CPBCY data. • MV_TAB: MV Table Selection In MB layer specifies which table is used to decode the MV data. Range: 0-3 for progressive content. 0-7 for interlaced content. • MB_MODE_TAB: MB Mode Syntax Table Selection MB mode syntax element table selection. • YAC_TAB: Luma AC table Specifies which of three table sets are used in decoding luma AC coefficients in block level. • CAC_TAB: Chroma AC table Specifies which of three table sets are used in decoding Chroma AC coefficients in block level. • TDC_TAB: Transform DC table Specifies in block level which of two tables is used to decode the Transform DC coefficients in intra-coded blocks. • FAST_UVMC: Chroma Interpolation Accuracy Information about chrominance interpolation accuracy (MVD): 0: 1/4pel chroma motion compensation is used. 1: 1/2pel chroma motion compensation is used. 1332 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• IS_REDU: Picture Range Reduction Is current picture range reduced: 0: No 1: Yes • DQBI: Quantization Step Size 0: Each macroblock may take on any quantization step size (STREAMD). 1: Only PQUANT and ALT_PQUANT allowed in Decoder control register 4. Used if DQUANT =1 in Decoder control register 4 and Q_PROFILE =1. • Q_PROFILE: Quantization Profile 0: Picture edges 1: All macroblocks • SYNCMAREN: Synchronization Markers Enable 0: Synch markers are not used. 1: Synch markers are used. • STREAM_START_BIT: Stream Start Bit Exact bit of stream start word where decoding can be started. SAM9M11 [DATASHEET] 1333 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.7 Decoder Control Register 3 (Stream Buffer Information) Name: VDEC_CTLR3 Address: 0x00900018 Access: Read/Write 31 30 29 28 27 26 25 24 ST_COD_EN INIT_QP – 23 22 21 20 19 18 17 16 STREAM_LEN 15 14 13 12 11 10 9 8 STREAM_LEN 7 6 5 4 3 2 1 0 STREAM_LEN • STREAM_LEN: Stream Length Amount of stream data bytes in input buffer. If the given buffer size is not enough for finishing the picture, the correspond- ing interrupt is given and new stream buffer base address and stream buffer size information should be given. For VC-1 the buffer must include data for one picture/slice of the picture. • INIT_QP: Quantization Initialization Initial value for quantization parameter (picture quantizer). • ST_COD_EN: Stream Start Code Stream start codes exist: 0: Stream does not contain start codes. 1: Stream contains start codes. 1334 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.8 Decoder Control Register 4 (VC-1 Control) Name: VDEC_CTLR4 Address: 0x0090001C Access: Read/Write 31 30 29 28 27 26 25 24 BIT_PLAN0 BIT_PLAN1 BIT_PLAN2 ALT_PQUANT 23 22 21 20 19 18 17 16 DQ_EDGES TTMBF PQ_INDEX 15 14 13 12 11 10 9 8 PQ_INDEX – BILIN UNIQ HALFQP TTFRM 7 6 5 4 3 2 1 0 – DQUANT VC1_ADV – – – – – • VC1_ADV: VC-1 Advance Profile 1: VC-1 advanced profile enable. • DQUANT: Data Quantization Does quantization parameter change inside frame enable: 0: PQUANT used throughout. 1: Yes. • TTFRM: VC-1 Frame Level Transformation Type 0: 8x8 transform 1: 8x4 transform 2: 4x8 transform 3: 4x4 transform • HALFQP: Inverse Quantization 1: HALFQP enable. Used for VC-1 inverse quantization. • UNIQ: Uniform Quantization 1: Uniform quantizer enable. Used for VC-1 inverse quantization. • BILIN: Bilinear Enable Bilinear motion compensation enable: 0: Bicubic interpolation used. 1: Bilinear interpolation used. • PQ_INDEX: Pre Quantization index Value of pqindex, used for forming pquant. SAM9M11 [DATASHEET] 1335 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• TTMBF: TTMB Flag 0: TTMB is present in MB header. 1: TTFRM syntax element exists in the picture layer. TTMB is not present. • DQ_EDGES: Quantized Edge Specifies which edges will be quantized using ALT_PQUANT, if Q_PROFILE set to picture edges in Video Decoder Con- trol Register 3. 0: Left edge 2: Top edge 4: Right edge 8: Bottom edge Other: Reserved • ALT_PQUANT: Alternative PQUANT Used if DQUANT = 1. • BIT_PLAN2: Bitplane Mode Enable 2 Bitplane mode enable for corresponding element. • BIT_PLAN1: Bitplane Mode Enable 1 Bitplane mode enable for corresponding element. • BIT_PLAN0: Bitplane Mode Enable 0 Bitplane mode enable for corresponding element. 1336 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.9 Decoder Control Register 5 (VC-1 Control) Name: VDEC_CTLR5 Address: 0x0090001C Access: Read/Write 31 30 29 28 27 26 25 24 SCALE_FACTOR 23 22 21 20 19 18 17 16 REF-DIST_FWD REF_DIST_BWD 15 14 13 12 11 10 9 8 REF_DIST_BWD – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – – • REF_DIST_BWD: VC-1 Reference Distance for BWD Direction VC-1 reference distance for BWD direction (used for B type pictures). • REF_DIST_FWD: VC-1 Reference Distance for FWD Direction VC-1 reference distance for FWD direction. • SCALE_FACTOR: Scale Factor Scaling factor for B picture direct mode motion vectors Used only for B pictures. SAM9M11 [DATASHEET] 1337 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.10 Decoder Control Register 6 (VC-1 Intensity Control 0) Name: VDEC_CTLR6 Address: 0x00900024 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – ICOMP0 23 22 21 20 19 18 17 16 IScale0 15 14 13 12 11 10 9 8 ISHIFT0 7 6 5 4 3 2 1 0 ISHIFT0 • ISHIFT0: IShift Value IShift value used for VC-1 intensity compensation. • IScale0: IScale Value IScale value used for VC-1 intensity compensation. • ICOMP0: Intensity Compensation Value Intensity compensation 0 enable. 1338 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.11 Differential Motion Vector Base Address (VC-1 Intensity Control 1) Name: VDEC_DMVBA Address: 0x00900028 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – ICOMP1 23 22 21 20 19 18 17 16 IScale1 15 14 13 12 11 10 9 8 ISHIFT1 7 6 5 4 3 2 1 0 ISHIFT1 • ISHIFT1: IShift Value IShift value used for VC-1 intensity compensation. • IScale1: IScale Value IScale value used for VC-1 intensity compensation. • ICOMP1: Intensity Compensation Value Intensity compensation 1 enable. SAM9M11 [DATASHEET] 1339 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.12 Decoder Control Register 7 (VC-1 Intensity Control 2) Name: VDEC_CTLR7 Address: 0x0090002C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – ICOMP2 23 22 21 20 19 18 17 16 IScale2 15 14 13 12 11 10 9 8 ISHIFT2 7 6 5 4 3 2 1 0 ISHIFT2 • ISHIFT2: Ishift Value IShift value used for VC-1 intensity compensation. • IScale2: IScale Value IScale value used for VC-1 intensity compensation. • ICOMP2: Intensity Compensation Value Intensity compensation 2 enable. 1340 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.13 RLC/VLC Data Base Address Name: VDEC_RLCVLCBA Address: 0x00900030 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address RLC_mode: Base address for RLC data (RLCEN = 1 in Decoder Control Register 0). VLC_mode: Stream start address/end address with byte precision (RLCEN = 0 in Decoder Control Register 0) STREAM_START_BIT field in Decoder Control Register 0. When SBE = 1 or DE = 0 in Decoder Interrupt Register, this register contains HW return value of last byte address (not valid for jpeg) where stream has been read (and used) in accu- racy of byte. For debug purposes, the last byte address is also written when stream error/ASO is detected even though it may not be accurate. SAM9M11 [DATASHEET] 1341 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.14 Decoded Picture Base Address (Video, JPEG Decoder Output Luma Picture) Name: VDEC_PICTBA Address: 0x00900034 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Video: Base address for decoder output picture. Points directly to start of decoder output picture or field. 1342 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.15 Reference Picture Index 0 Base Address (Video, JPEG Decoder Output Chroma Picture) Name: VDEC_PIDXBA0 Address: 0x00900038 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Video: Base address for reference picture index 0. SAM9M11 [DATASHEET] 1343 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.16 Reference Picture Index 1 Base Address (Video) Name: VDEC_PIDXBA1 Address: 0x0090003C Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for reference picture index 1. 1344 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.17 Reference Picture Index 2 Base Address (Video) Name: VDEC_PIDXBA2 Address: 0x00900040 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for reference picture index 2. SAM9M11 [DATASHEET] 1345 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.18 Reference Picture Index 3 Base Address (Video) Name: VDEC_PIDXBA3 Address: 0x00900044 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for reference picture index 3. 1346 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.19 Reference Picture Index 4 Base Address Name: VDEC_PIDXBA4 Address: 0x00900048 Access: Read/Write 31 30 29 28 27 26 25 24 HEADER_LEN 23 22 21 20 19 18 17 16 HEADER_LEN 15 14 13 12 11 10 9 8 – – PIC_4M – RED_REF_EN DIFF_MV_RANGE – 7 6 5 4 3 2 1 0 MV_RANGE OVERLAP_EN OVERLAP_MET ACC_FW RCB ANC • ANC: Anchor Picture Type Previous anchor picture type: 0: Intra 1: Inter • RCB: Rounding Control Bit When low, 1/2 pixel motion compensation sum is rounded, otherwise clipped. • ACC_FW: Forward Motion Vector Forward motion vector Y resolution: 0: 1/2 accuracy 1: 1/4 accuracy • OVERLAP_SM: Overlap Smoothing Method Overlap smoothing method for macroblocks where PQUANT <= 8: 0: No overlap smoothing. 1: All macroblocks overlap smoothed. 2: Overlap smoothing depends on overflagmb syntax element per macroblock. • OVERLAP_EN: Overlap Smoothing Enable Overlap smoothing enable. Defines if overlap smoothing is enabled for current picture (includes information about PQUANT which must be >= 9). SAM9M11 [DATASHEET] 1347 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• MV_RANGE: Motion Vector Range This control gives range to motion vectors: 0: Range is [-64,63.f],[-32,31.f]. 1: Range is [-128,127.f],[-64,63.f]. 2: Range is [-512,511.f],[-128,127.f]. 3: Range is [-1024,1023.f],[-256,255.f]. • DIFF_MV_RANGE: Differential Motion Vector Range Specifies maximum differential motion vector length (advanced profile only). • RED_REF_EN: Range Reduce Enable Reference picture range reduce enable: 0: Disabled 1: Enabled • PIC_4M: 4M Pictures Allowed 0: Only 1 MV/MB. 1: 4 MV/MB allowed. • HEADER_LEN: Header Length Length of picture header in bits. 1348 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.20 Reference Picture Index 5 Base Address Name: VDEC_PIDXBA5 Address: 0x0090004C Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – ICOMP3 23 22 21 20 19 18 17 16 IScale3 15 14 13 12 11 10 9 8 ISHIFT3 7 6 5 4 3 2 1 0 ISHIFT3 • ISHIFT3: Ishift Value IShift value used for VC-1 intensity compensation. • IScale3: IScale Value IScale value used for VC-1 intensity compensation. • ICOMP3: Intensity Compensation Value Intensity compensation 3 enable. SAM9M11 [DATASHEET] 1349 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.21 Reference Picture Index 6 Base Address (VC-1 Intensity Control 4) Name: VDEC_PIDXBA6 Address: 0x00900050 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – ICOMP4 23 22 21 20 19 18 17 16 IScale4 15 14 13 12 11 10 9 8 ISHIFT4 7 6 5 4 3 2 1 0 ISHIFT4 • ISHIFT4: Ishift Value IShift value used for VC-1 intensity compensation. • IScale4: IScale Value IScale value used for VC-1 intensity compensation. • ICOMP4: Intensity Compensation Value Intensity compensation 4 enable. 1350 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.22 Reference Picture Index 13 Base Address (VC-1) Name: VDEC_PIDXBA13 Address: 0x0090006C Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address VC-1: Base address for VC-1 bitplane mb control. SAM9M11 [DATASHEET] 1351 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.23 Direct Mode Motion Vector Base Address Name: VDEC_DMMVBA Address: 0x009000A4 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Not used in JPEG mode. 1352 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.9.24 Error Concealment Register Name: VDEC_ECR Address: 0x009000C0 Access: Read/Write 31 30 29 28 27 26 25 24 STARTMB_X 23 22 21 20 19 18 17 16 STARTMB_X STARTMB_Y 15 14 13 12 11 10 9 8 STARTMB_Y – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – – • STARTMB_Y: Start MB from SW for Y Dimension. Used in error concealment case. Not used in JPEG mode. • STARTMB_X: Start MB from SW for X Dimension. Used in error concealment case. Not used in JPEG mode. SAM9M11 [DATASHEET] 1353 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10 Video Decoder Register Mapping (MPEG-2/MPEG-1) Table 48-14. Video Decoder Register Mapping (MPEG-2/MPEG-1) Offset Register Name Access Reset 0x0000 ID Register VDEC_IDR Read-only 0x81700880 0x0004 Decoder Interrupt Register VDEC_DIR Read/Write 0x00000000 0x0008 Decoder Device Configuration Register VDEC_DDCR Read/Write 0x00000400 0x000C Decoder Control Register 0 VDEC_CTLR0 Read/Write 0x00000000 0x0010 Decoder Control Register 1 VDEC_CTLR1 Read/Write 0x00000000 0x0014 Decoder Control Register 2 VDEC_CTLR2 Read/Write 0x00000000 0x0018 Decoder Control Register 3 VDEC_CTLR3 Read/Write 0x00000000 0x001C–0x002C Reserved – – – 0x0030 RLC/VLC Data Base Address VDEC_RLCVLCBA Read/Write 0x00000000 0x0034 Decoded Picture Base Address VDEC_PICTBA Read/Write 0x00000000 0x0038 Reference Picture Index 0 Base Address VDEC_PIDXBA0 Read/Write 0x00000000 0x003C Reference Picture Index 1 Base Address VDEC_PIDXBA1 Read/Write 0x00000000 0x0040 Reference Picture Index 2 Base Address VDEC_PIDXBA2 Read/Write 0x00000000 0x0044 Reference Picture Index 3 Base Address VDEC_PIDXBA3 Read/Write 0x00000000 0x0048 Reference Picture Index 4 Base Address VDEC_PIDXBA4 Read/Write 0x00000000 0x004C–0x009C Reserved – – – 0x00A0 Standard Dependent Tables Base Address VDEC_SDTBA Read/Write 0x00000000 0x00A4 Direct Mode Motion Vector Base Address VDEC_DMMVBA Read/Write 0x00000000 0x00A8–0x00BC Reserved – – – 0x00C0 Error Concealment Register VDEC_ECR Read/Write 0x00000000 0x00C4 Reserved – – – 0x00C8 Reserved – – – 1354 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.1 Video Decoder ID Register Name: VDEC_IDR Address: 0x00900000 Access: Read-Only 31 30 29 28 27 26 25 24 PROD_ID 23 22 21 20 19 18 17 16 PROD_ID 15 14 13 12 11 10 9 8 MAJOR_VER MINOR_VER 7 6 5 4 3 2 1 0 MINOR_VER BUILD_VER • BUILD_VER: Build Version Build Version is 0x0. • MINOR_VER: Minor Version Minor Version is 0x88. • MAJOR_VER: Major Version Major Version is 0x0. • PROD_ID: Product ID Product ID is 0x8170. SAM9M11 [DATASHEET] 1355 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.2 Decoder Interrupt Register Name: VDEC_DIR Address: 0x00900004 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – TO – ISE 15 14 13 12 11 10 9 8 ASOD SBE BE DR – – – ISET 7 6 5 4 3 2 1 0 – – – ID – – – DE • DE: Decoder Enable 0: Disables decoder. 1: Enables decoder. Setting this bit high will start the decoding operation. Hardware will reset this bit when a picture is processed, a stream error or ASO is detected or a bus error is received. • ID: Interrupt Disable 0: Enables interrupts for decoder. 1: Disables interrupts for decoder. When high, there will be no interrupts issued by the decoder. Polling must be used to see the hardware status. • ISET: Decoder Interrupt Set 0: Clears the decoder interrup.t Software will reset this after the interrupt is handled. 1: Set the decoder interrupt. This bit drives the interrupt line, OR gated with the post-processor interrupt bit. The interrupt line is not used for the decoder if the interrupt disable bit for decoder is high. • DR: Decoder Ready 0: Decoding in progress. 1: Decoder is ready. When high, the hardware has decoded a picture. Hardware will self-reset. • BE: Bus Error 0: No error. 1: A bus error has occurred. When high, hardware has received an error response from the bus while accessing external memory. This is a fatal error possibly caused by the incorrect allocation of decoder linear memory. Hardware will self-reset. 1356 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• SBE: Stream Buffer Empty 0: Stream Buffer is not empty 1: Input Stream Buffer is empty but the picture is not ready. Software must provide a new stream pointer to hardware. Hardware will not self-reset. • ASOD: ASO Detected 0: No ASO detected. 1: Interrupt status flag ASO detected. Hardware has encountered Arbitrary Slice Order tool in the input H.264 stream data, and software must perform entropy decoding. Hardware will self-reset. • ISE: Input Stream Error 0: No error. 1: Interrupt stream error occurs. When high, hardware has encountered a bit error in the input stream data, and software must perform error concealment. Hardware will self-reset. • TO: Timeout 0: No timeout 1: Timeout occurs When high, decoder has made no bus transactions in 218-1 clock cycles and has not set an interrupt. Possible only if time- out interrupting is enabled. This should be considered as an encountered error in the input stream. Note: Post-processor transactions affect this feature; running stand-alone post-processing while decoding may prevent decoder timeout interrupts. SAM9M11 [DATASHEET] 1357 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.3 Decoder Device Configuration Register Name: VDEC_DDCR Address: 0x00900008 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 HTI – DI_LE – – AHB_BURST DOPF LAT_COMP 15 14 13 12 11 10 9 8 LAT_COMP DDCGE INTCE_LE DO_LE 7 6 5 4 3 2 1 0 PRIOR MAX_BURST_LEN • MAX_BURST_LEN: Maximum burst length for decoder bus transactions Valid values for AHB are 0, 1, 4, 8, 16 and 17. 0: INCR transfer type is used always. 1: SINGLE transfer type is used always. 4: INCR4, INCR and SINGLE transfers are allowed. INCR used for 2 and 3 bursts. 8: INCR8, INCR4, INCR and SINGLE transfers are allowed. INCR used for 2 and 3 bursts. 16: INCR16, INCR8, INCR4, INCR and SINGLE transfers are allowed. INCR used for 2 and 3 bursts. 17: INCR16, INCR8, INCR4, INCR and SINGLE transfers are allowed. INCR used for 2, 3, 5, 6, 7, 9, 10, 11, 12, 13, 14 and 15 bursts. • PRIOR: Decoder core internal bus service priority 0: Dynamic priority depending on stream content. 1: Post-processor output write has highest priorit.y 2: Input stream read has highest priority. 3: Reference picture read has highest priority, then post-processor transactions. 4: Reference picture read has highest priority, then decoder output write. • DO_LE: Decoder Output Endian Mode 0: Big endian 1: Little endian • INTCE_LE: Interface Endian Mode 0: Big endian 1: Little endian 1358 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• DDCGE: Decoder Dynamic Clock Gating Enable 0: Clock is running for all structures. 1: Clock is gated for decoder structures that are not used. Clock gating value should be changed only when the decoder is disabled. • LAT_COMP: Decoder Latency Compensation Decoder latency compensation value in clock cycles. If the best case latency (from bus request to bus grant, or from data request to data receive) is known, the value can be written to these register bits used to compensate the delay. If the latency value is unknown, these bits should be written to zero. Note: Setting the compensation value higher than the best case latency can cause data corruption. • DOPF: Decoder Output Picture Format 0: Output format is raster scan, i.e., pixel rows are written in consecutive memory 1: Output format is tiled, i.e., macroblocks are written in consecutive memory addresses. • AHB_BURST: AHB Precise Burst and Data Discard Enable 0: INCR bursts of undefined length 2 or 3 may be issued when necessary. 1: Only the precise AHB bursts (SINGLE, INCR4, INCR8 and INCR16) are used in SDRAM read accesses. Extra data is discarded internally. • DI_LE: Decoder Input Endian Mode 0: Big endian 1: Little endian • HTI: Hardware Timeout Interrupt Enable 0: Hardware timeout interrupt disable. 1: Hardware timeout interrupt enable. SAM9M11 [DATASHEET] 1359 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.4 Decoder Control Register 0 (Decoder Mode And Picture Type) Name: VDEC_CTLR0 Address: 0x0090000C Access: Read/Write 31 30 29 28 27 26 25 24 DEC_MODE – – – – 23 22 21 20 19 18 17 16 PICMODE PICSTRUCT PICBEN PICTYPE PICFIELD FORWMODE – – 15 14 13 12 11 10 9 8 OUTDIS FILTDIS QUANT MV REFFIRST – – HLOCK 7 6 5 4 3 2 1 0 – – – – – – – – • HLOCK: HLOCK Enable 0: Locked transfers disabled. 1: Locked transfers enabled. When a locked transfer is granted, bus grant cannot be lost even if a higher priority master requests the bus. • REFFIRST: Reference Field First Indicates which FWD reference field has been decoded first. 0: FWD reference bottom field. 1: FWD reference top field. • MV: MPEG-2 Motion Vector Write Enable Direct mode motion vector write enable / MPEG2 motion vector write enable for error concealment purposes: 0: Writing disabled for current picture. 1: The direct mode motion vectors are written to external memory starting from MV_BASE in Direct mode motion vector write/read base address register (offset 0x00a8). • QUANT: Quantization 0: Quantization parameter can vary inside picture. 1: Quantization parameter is fixed (pquant). • FILTDIS: De-block Filtering Disable 0: Filtering is enabled for current picture. 1: Filtering is disabled for current picture. • OUTDIS: Disable Decoder Output Picture Writing 0: Decoder output picture is written to external memory. 1: Decoder output picture is not written to external memory. 1360 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• FORWMODE: Coding Mode Of Forward Reference Picture 0: Progressive 1: Interlaced Note: For backward reference picture, the coding mode is always same as for current picture. • PICFIELD: Picture Field If field structure is enabled, this bit informs which one of the fields is being decoded: 0: Bottom field 1: Top field • PICTYPE: Picture Type 0: Intra type (I) 1: Inter type (P) • PICBEN: B Picture Enable B picture enable for current picture: 0: Picture type is I or P depending on PICTYPE. 1: Picture type is BI (vc1)/D (mpeg1) or B depending on PICTYPE. • PICSTRUCT: Structure of the Current Picture Structure of the current picture (residual structure): 0: Frame structure. For H.264 this means MBAFF structured picture for interlaced sequence. 1: Field structure. • PICMODE: Coding Mode Of Current Picture 0: Progressive 1: Interlaced • DEC_MODE: Decoding Mode 0: H.264 1: MPEG-4 2: H.263 3: JPEG 4: VC-1 5: MPEG2 6: MPEG1 7: Reserved SAM9M11 [DATASHEET] 1361 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.5 Decoder Control Register 1 (Picture Parameters) Name: VDEC_CTLR1 Address: 0x00900010 Access: Read/Write 31 30 29 28 27 26 25 24 PIC_WIDTH 23 22 21 20 19 18 17 16 PIC_WIDTH – – – – PIC_HEIGHT 15 14 13 12 11 10 9 8 PIC_HEIGHT – – – 7 6 5 4 3 2 1 0 – AVSM – – – – – – • AVSM: Alternative Vertical Scan Method Indicates alternative vertical scan method used for interlaced frames. • PIC_HEIGHT: Picture Height Picture height in macroblocks = ((height in pixels+15)/16). Picture height is informed as size of the (progressive) frame even though a single field (of interlaced content) is being decoded. • PIC_WIDTH: Picture Width Picture width in macroblocks = ((width in pixels + 15) /16). 1362 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.6 Decoder Control Register 2 (MPEG-2/MPEG-1 Stream Decoding Table Selects) Name: VDEC_CTLR2 Address: 0x00900014 Access: Read/Write 31 30 29 28 27 26 25 24 STREAM_START_BIT – Q_SCALE 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – CON_MV INTRA_DC VLC_TAB PRED_DCT • PRED_DCT: Frame Prediction Semantics Defines frame prediction semantics for MPEG2/MPEG1. • VLC_TAB: Intra VLC Table Selection Intra VLC table selection. • INTRA_DC: Intra DC Precision Determines intra DC precision. • CON_MV: Concealed Motion in Stream Presence of concealed motion vectors in stream: 0: No concealed motion vectors in stream. 1: Concealed motion vectors present in stream. • SYNCMAREN: Synchronization Markers Enable 0: Synch markers are not used. 1: Synch markers are used. • Q_SCALE: Q Scale Type Semantics Defines Q scale type semantics. • STREAM_START_BIT: Stream Start Bit Exact bit of stream start word where decoding can be started. SAM9M11 [DATASHEET] 1363 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.7 Decoder Control Register 3 (Stream Buffer Information) Name: VDEC_CTLR3 Address: 0x00900018 Access: Read/Write 31 30 29 28 27 26 25 24 ST_COD_EN INIT_QP – 23 22 21 20 19 18 17 16 STREAM_LEN 15 14 13 12 11 10 9 8 STREAM_LEN 7 6 5 4 3 2 1 0 STREAM_LEN • STREAM_LEN: Stream Length Amount of stream data bytes in input buffer. If the given buffer size is not enough for finishing the picture the corresponding interrupt is given and new stream buffer base address and stream buffer size information should be given. For VC-1 the buffer must include data for one picture/slice of the picture. For H264/MPEG4/H263/MPEG2/MPEG1 the buffer must include at least data for one slice/VP of the picture. For JPEG the buffer size must be a multiple of 256 bytes or the amount of data for one picture. • INIT_QP: Quantization Initialization Initial value for quantization parameter (picture quantizer). • ST_COD_EN: Stream Start Code Stream start codes exist: 0: Stream does not contain start codes. 1: Stream contains start codes. 1364 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.8 RLC/VLC Data Base Address Name: VDEC_RLCVLCBA Address: 0x00900030 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address RLC_mode: Base address for RLC data (RLCEN = 1 in Decoder Control Register 0). VLC_mode: Stream start address/end address with byte precision (RLCEN = 0 in Decoder Control Register 0) STREAM_START_BIT field in Decoder Control Register 0. When SBE = 1 or DE = 0 in Decoder Interrupt Register, this register contains HW return value of last byte address (not valid for jpeg) where stream has been read (and used) in accu- racy of byte. For debug purposes, the last byte address is also written when stream error/ASO is detected even though it may not be accurate. SAM9M11 [DATASHEET] 1365 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.9 Decoded Picture Base Address (Video) Name: VDEC_PICTBA Address: 0x00900034 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Video: Base address for decoder output picture. Points directly to start of decoder output picture or field. 1366 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.10 Reference Picture Index 0 Base Address (Video) Name: VDEC_PIDXBA0 Address: 0x00900038 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Video: Base address for reference picture index 0. SAM9M11 [DATASHEET] 1367 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.11 Reference Picture Index 1 Base Address (Video) Name: VDEC_PIDXBA1 Address: 0x0090003C Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for reference picture index 1. 1368 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.12 Reference Picture Index 2 Base Address (Video) Name: VDEC_PIDXBA2 Address: 0x00900040 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for reference picture index 2. SAM9M11 [DATASHEET] 1369 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.13 Reference Picture Index 3 Base Address (Video) Name: VDEC_PIDXBA3 Address: 0x00900044 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for reference picture index 3. 1370 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.14 Reference Picture Index 4 Base Address (MPEG-2/MPEG-1) Name: VDEC_PIDXBA4 Address: 0x00900048 Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – SCANF FW_HOR_BN 15 14 13 12 11 10 9 8 FW_HOR_BN FW_VER_BN BW_HOR_BN 7 6 5 4 3 2 1 0 BW_HOR_BN BW_VER_BN ACC_FW ACC_BW – • ACC_BW: Forward Motion Vector Backward motion vector Y resolution. 0: 1 pel 1: 1/2 pel • ACC_FW: Forward Motion Vector Forward motion vector Y resolution. 0: 1 pel 1: 1/2 pel • BW_VER_BN: Backward Vertical Bit Number Bit amount for representing backward motion vector fin vertical axis. • BW_HOR_BN: Backward Horizontal Bit Number Bit amount for representing backward motion vector fin horizontal axis. • FW_VER_BN: Forward Vertical Bit Number Bit amount for representing forward motion vector fin vertical axis. • FW_HOR_BN: Forward Horizontal Bit Number Bit amount for representing forward motion vector fin horizontal axis. • SCANF: Alternate Scan Flag SAM9M11 [DATASHEET] 1371 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.15 Standard Dependent Tables Base Address Name: VDEC_SDTBA Address: 0x009000A0 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for standard dependent tables 1372 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.16 Direct Mode Motion Vector Base Address Name: VDEC_DMMVBA Address: 0x009000A4 Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address SAM9M11 [DATASHEET] 1373 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.10.17 Error Concealment Register Name: VDEC_ECR Address: 0x009000C0 Access: Read/Write 31 30 29 28 27 26 25 24 STARTMB_X 23 22 21 20 19 18 17 16 STARTMB_X STARTMB_Y 15 14 13 12 11 10 9 8 STARTMB_Y – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – – • STARTMB_Y: Start MB from SW for Y Dimension. Used in error concealment case. Not used in JPEG mode. • STARTMB_X: Start MB from SW for X Dimension. Used in error concealment case. Not used in JPEG mode. 1374 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11 Video Post-processor Register Mapping (All Decoders) Table 48-15. Video Post-processor Register Mapping Offset Register Name Access Reset 0x00F0 Post Processor Interrupt Register VDEC_PPIR Read/Write 0x00000000 0x00F4 Post Processor Device Configuration Register VDEC_PPCR Read/Write 0x00000200 0x00F8 Post Processor Deinterlace Control Register VDEC_PPDCR Read/Write 0x00000000 0x00FC Post Processor Input Y Top Field Picture Base Address VDEC_PIYTBA Read/Write 0x00000000 0x0100 Post Processor Input Cb Top Field Picture Base Address VDEC_PICBTBA Read/Write 0x00000000 0x0104 Post Processor Input Cr Picture Base Address VDEC_PICRBA Read/Write 0x00000000 0x0108 Post Processor Output Y Picture Base Address VDEC_POYBA Read/Write 0x00000000 0x010C Post Processor Output C Picture Base Address VDEC_POCBA Read/Write 0x00000000 0x0110 Post Processor Contrast Adjustment Register VDEC_CAR Read/Write 0x00000000 Post Processor Contrast Adjustment and Color Conversion 0x0114 VDEC_CACCR Read/Write 0x00000000 Register 0x0118 Post Processor Color Conversion Register VDEC_CCR Read/Write 0x00000000 0x011C Post Processor Color Conversion and Rotation Mode Register VDEC_CCRMR Read/Write 0x00000000 0x0120 Post Processor Input Picture Size and Cropping Register VDEC_PISCR Read/Write 0x00000000 0x0124 Post Processor Input Y Bottom Field Picture Base Address VDEC_PIYBBA Read/Write 0x00000000 0x0128 Post Processor Input Cb Bottom Field Picture Base Address VDEC_PICBBBA Read/Write 0x00000000 0x012C–0x0138 Reserved – – – 0x013C Post Processor R and G Padding and Scaling Ratio Register 0 VDEC_RGPSRR0 Read/Write 0x00000000 0x0140 Post Processor B Padding and Scaling Ratio Register 1 VDEC_BPSRR1 Read/Write 0x00000000 0x0144 Post Processor Scaling Ratio Register 2 VDEC_SRR2 Read/Write 0x00000000 0x0148 Post Processor Red Channel Mask Register VDEC_REDMR Read/Write 0x00000000 0x014C Post Processor Green Channel Mask Register VDEC_GREMR Read/Write 0x00000000 0x0150 Post Processor Blue Channel Mask Register VDEC_BLUMR Read/Write 0x00000000 0x0154 Post Processor Control Register VDEC_CTLR Read/Write 0x00000000 0x0158 Post Processor Mask 1 Start Coordinate Register VDEC_M1STR Read/Write 0x00000000 0x015C Post Processor Mask 2 Start Coordinate Register VDEC_M2STR Read/Write 0x00000000 0x0160 Post Processor Mask 1 Size And Pp Original Width Register VDEC_M1SZOWR Read/Write 0x00000000 0x0164 Post Processor Mask 2 Size Register VDEC_M2SZR Read/Write 0x00000000 0x0168 Post Processor Picture-in-picture Register 0 VDEC_PIPR0 Read/Write 0x00000000 0x016C Post Processor Dithering and Picture-in-picture Register 1 VDEC_DPIPR1 Read/Write 0x00000000 0x0170 Post Processor Display Width Register VDEC_DWR Read/Write 0x00000000 Post Processor Alpha Blending GUI Component 1 Base 0x0174 VDEC_ABGUI1BA Read/Write 0x00000000 Address Post Processor Alpha Blending GUI Component 2 Base 0x0178 VDEC_ABGUI2BA Read/Write 0x00000000 Address 0x017C–0x018C Reserved – – – 0x0190 Reserved – – – SAM9M11 [DATASHEET] 1375 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.1 Post-Processor Interrupt Register Name: VDEC_PPIR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – BE PPR – – – ISET 7 6 5 4 3 2 1 0 – – – ID – – PIPE PPE • PPE: Post-processor Standalone Enable 0: Disables post-processor. 1: Enables post-processor. Setting this bit high will start the post-processing operation. Hardware will reset this bit when a picture is processed. • PIPE: Decoder Post-processing Pipeline Enable 0: Disables the pipeline. 1: Enables the pipeline. When high, post-processing is performed in pipeline with decoder. When low, post-processor is processing different pic- ture than the decoder. • ID: Interrupt Disable 0: Enables Interrupts for post-processor. 1: Disables Interrupts for post-processor. When high, there will be no interrupts issued by the post-processor. Polling must be used to see the hardware status. • ISET: Post-processor Interrupt Set 0: Clears the post-processor Interrupt. Software will reset this after the interrupt is handled. 1: Set the post-processor interrupt. This bit drives the interrupt line, OR gated with the decoder interrupt bit. Software will reset this after the interrupt is handled. The interrupt line is not used if the interrupt disable bit for post-proces- sor is high. • PPR: Post-processor Ready 0: Post processing in progress. 1: Post-processor is ready. If decoder and post-processor are running in pipeline, this bit is not used. When high, the hardware has post-processed a picture. Hardware will self-reset. 1376 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• BE: Bus Error 0: No error. 1: A bus error has occurred. When high, hardware has received an error response from the bus while accessing external memory. This is a fatal error possibly caused by the incorrect allocation of post-processor linear memory. Hardware will self-reset. SAM9M11 [DATASHEET] 1377 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.2 Post Processor Device Configuration Register Name: VDEC_PPCR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 HLOCK – – – – – AHB_BURST PPDCGE 7 6 5 4 3 2 1 0 PPI_LE PPO_LE – MAX_BURST_LEN • MAX_BURST_LEN: Maximum burst length for post-processor bus transactions Valid values for AHB are 0, 1, 4, 8 and 16. 0: AHB INCR transfer type is used always. 1: AHB SINGLE transfer type is used always. 4, 8, 16: Set AHB maximum burst length to INCR4, INCR8 or INCR16. Also INCR and SINGLE types are allowed. • PPO_LE: Post-processor Output Endian Mode (for Y Cb Cr) 0: Big endian 1: Little endian For 16-bit RGB data, this bit woks as a pixel swapping bit. • PPI_LE: Post-processor Input Endian Mode 0: Big endian 1: Little endian • PPDCGE: Post-processor Dynamic Clock Gating Enable 0: Clock is running for all post-processor structures. 1: Clock is gated for post-processor structures that are not used. Clock gating value should be changed only when the post-processor is disabled. • AHB_BURST: AHB precise burst and data discard enable 0: INCR bursts of undefined length 2 or 3 may be issued when necessary. 1: Only the precise AHB bursts (SINGLE, INCR4, INCR8 and INCR16) are used in SDRAM read accesses. Extra data is discarded internally. • HLOCK: HLOCK enable 0: Locked transfers disabled. 1: Locked transfers enabled. When a locked transfer is granted, bus grant cannot be lost even if a higher priority master requests the bus. 1378 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.3 Post Processor Deinterlace Control Register Name: VDEC_PPDCR Access: Read/Write 31 30 29 28 27 26 25 24 DEINT_EN – DEINT_THRD 23 22 21 20 19 18 17 16 DEINT_THRD 15 14 13 12 11 10 9 8 BLEND_EN EDGE_DET_VAL 7 6 5 4 3 2 1 0 EDGE_DET_VAL • EDGE_DET_VAL: Edge Detect Value Used for deinterlacing. • BLEND_EN: Blend Enable for Deinterlacing • DEINT_THRD: Threshold Value Used in Deinterlacing • DEINT_EN: Deinterlace Enable. Input data is in interlaced format and deinterlacing needs to be performed. SAM9M11 [DATASHEET] 1379 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.4 Post Processor Input Y Top Field Picture Base Address Name: VDEC_PIYTBA Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for post-processing input luminance picture. If PP input picture is fetched from fields, this base address is used to point to top field of the picture. Used in external mode only. 1380 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.5 Post Processor Input Cb Top Field Picture Base Address Name: VDEC_PICBTBA Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for post-processing input Cb picture or for both chrominance pictures (if Chrominance interleaved). If PP input picture is fetched from fields, this base address is used to point to top field of the picture. Used in external mode only. SAM9M11 [DATASHEET] 1381 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.6 Post Processor Input Cr Picture Base Address Name: VDEC_PICRBA Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for post-processing input cr picture. Used in external mode only 1382 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.7 Post Processor Output Y Picture Base Address Name: VDEC_POYBA Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for post-processing output picture (luminance/YUYV/RGB). SAM9M11 [DATASHEET] 1383 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.8 Post Processor Output C Picture Base Address Name: VDEC_POCBA Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address Base address for post-processing output chrominance picture (interleaved chrominance). 1384 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.9 Post Processor Contrast Adjustment Register Name: VDEC_CAR Access: Read/Write 31 30 29 28 27 26 25 24 THRD1 23 22 21 20 19 18 17 16 BA – – – OFFSET2 15 14 13 12 11 10 9 8 OFFSET2 OFFSET1 7 6 5 4 3 2 1 0 OFFSET1 • OFFSET1: Offset Value 1 Used with contrast adjusting. • OFFSET2: Offset Value 2 Used with contrast adjusting. • THRD1: Threshold Value 1 Used with contrast adjusting. SAM9M11 [DATASHEET] 1385 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.10 Post Processor Contrast Adjustment and Color Conversion Register Name: VDEC_CACCR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – COEFF_A2 23 22 21 20 19 18 17 16 COEFF_A2 COEFF_A1 15 14 13 12 11 10 9 8 COEFF_A1 7 6 5 4 3 2 1 0 THRD2 • THRD2: Threshold Value 2 Used with contrast adjusting. • COEFF_A1: Coefficient a1 Coefficient a1, used with Y pixel to calculate all color components. • COEFF_A2: Coefficient a2 Coefficient a2, used with Y pixel to calculate all color components. 1386 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.11 Post Processor Color Conversion Register Name: VDEC_CCR Access: Read/Write 31 30 29 28 27 26 25 24 – – COEFF_D 23 22 21 20 19 18 17 16 COEFF_D COEFF_C 15 14 13 12 11 10 9 8 COEFF_C COEFF_B 7 6 5 4 3 2 1 0 COEFF_B • COEFF_B: Coefficient b Coefficient b, used with Cr to calculate red component value. • COEFF_C: Coefficient c Coefficient c, used with Cr to calculate green component value. • COEFF_D: Coefficient d Coefficient d, used with Cb to calculate green component value. SAM9M11 [DATASHEET] 1387 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.12 Post Processor Color Conversion and Rotation Mode Register Name: VDEC_CCRMR Access: Read/Write 31 30 29 28 27 26 25 24 – – CROPSTART_X 23 22 21 20 19 18 17 16 CROPSTART_X ROT_MODE COEFF_F 15 14 13 12 11 10 9 8 COEFF_F COEFF_E 7 6 5 4 3 2 1 0 COEFF_E • COEFF_E: Coefficient e Coefficient e, used with Cb to calculate blue component value. • COEFF_F: Coefficient f Coefficient f, used with Y to adjust brightness • ROT_MODE: Rotation Mode 0: Rotation disabled 1: Rotate + 90 2: Rotate – 90 3: Horizontal flip (mirror) 4: Vertical flip 5: Rotate 180 Other: Reserved • CROPSTART_X: Crop Area X Start coordinate x for the cropped area in macroblocks. 1388 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.13 Post Processor Input Picture Size and Cropping Register Name: VDEC_PISCR Access: Read/Write 31 30 29 28 27 26 25 24 CROPSTART_Y 23 22 21 20 19 18 17 16 – RANGEMAP_COEFF – – 15 14 13 12 11 10 9 8 IN_PICT_H 7 6 5 4 3 2 1 0 IN_PICT_W • IN_PICT_W: Input Picture Width PP input picture width in MBs. Can be cropped from a bigger input picture in external mode. • IN_PICT_H: Input Picture Height PP input picture height in MBs. Can be cropped from a bigger input picture in external mode. • RANGEMAP_COEFF: Range Map Value Range map value for Y component (RANGE_MAPY+9 in VC-1 standard). • CROPSTART_Y: Crop Area Y Start coordinate y for the cropped area in macroblocks. SAM9M11 [DATASHEET] 1389 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.14 Post Processor Input Y Bottom Field Picture Base Address Name: VDEC_PIYBBA Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address PP input Y base for bottom field. 1390 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.15 Post Processor Input Cb Bottom Field Picture Base Address Name: VDEC_PICBBBA Access: Read/Write 31 30 29 28 27 26 25 24 BA 23 22 21 20 19 18 17 16 BA 15 14 13 12 11 10 9 8 BA 7 6 5 4 3 2 1 0 BA – – • BA: Base Address PP input C base for bottom field (mixed chrominance). SAM9M11 [DATASHEET] 1391 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.16 Post Processor R and G Padding and Scaling Ratio Register 0 Name: VDEC_RGPSRR0 Access: Read/Write 31 30 29 28 27 26 25 24 MAP_Y_EN MAP_C_EN YCBCR_RAN RGBBY32 RGB_R_PADD 23 22 21 20 19 18 17 16 RGB_R_PADD RGB_G_PADD SCALE_W_RATIO 15 14 13 12 11 10 9 8 SCALE_W_RATIO 7 6 5 4 3 2 1 0 SCALE_W_RATIO • SCALE_W_RATIO: Scaling Ratio for Width (outputw-1/inputw-1) • RGB_G_PADD: Padding for G-component Amount of ones that will be padded in front of the G-component. • RGB_R_PADD: Padding for R-component Amount of ones that will be padded in front of the R-component. • RGBBY32: RGB Pixel Amount/32-bit Word 0: 1 RGB pixel/32-bit 1: 2 RGB pixels/32-bit • YCBCR_RAN: Defines the YCbCr Range in RGB Conversion 0: 16…235 for Y, 16…240 for Chrominance. 1: 0…255 for all components. • MAP_C_EN: Range map enable for chrominance component (RANGE_MAPUV_FLAG in VC-1 standard) • MAP_Y_EN: Range map enable for luminance component (RANGE_MAPY_FLAG in VC-1 standard). For VC1 main profile, this bit is used as range expansion enable. 1392 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.17 Post Processor B Padding and Scaling Ratio Register 1 Name: VDEC_BPSRR1 Access: Read/Write 31 30 29 28 27 26 25 24 – – PP_IN_STRUCT H_SCAL_MOD V_SCAL_MOD 23 22 21 20 19 18 17 16 V_SCAL_MOD RGB_B_PADD SCALE_H_RATIO 15 14 13 12 11 10 9 8 SCALE_H_RATIO 7 6 5 4 3 2 1 0 SCALE_H_RATIO • SCALE_H_RATIO: Scaling Ratio for Height (outputh-1/inputh-1) • RGB_B_PADD: Padding for B-component Amount of ones that will be padded in front of the B-component. • V_SCAL_MOD: Vertical Scaling Mode 0: Off 1: Upscale 2: Downscale • H_SCAL_MOD: Horizontal Scaling Mode 0: Off 1: Upscale 2: Downscale • PP_IN_STRUCT: PP Input Data Picture Structure 0: Top field/progressive frame structure: Read input data from top field base address/frame base address and read every line. 1: Bottom field structure: Read input data from bottom field base address and read every line. 2: Interlaced field structure: Read input data from both top and bottom field base address and take every line from each field. 3: Interlaced frame structure: Read input data from both top and bottom field base address and take every second line from each field. 4: Ripped top field structure: Read input data from top field base address and read every second line. 5: Ripped bottom field structure: Read input data from bottom field base address and read every second line. SAM9M11 [DATASHEET] 1393 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.18 Post Processor Scaling Ratio Register 2 Name: VDEC_SRR2 Access: Read/Write 31 30 29 28 27 26 25 24 W_SCALE_INV 23 22 21 20 19 18 17 16 W_SCALE_INV 15 14 13 12 11 10 9 8 H_SCALE_INV 7 6 5 4 3 2 1 0 H_SCALE_INV • H_SCALE_INV: Inverse Scaling for Height Inverse scaling ratio for height or cv (inputh-1 / outputh-1). • W_SCALE_INV: Inverse Scaling for Width Inverse scaling ratio for width, or ch (inputw-1 / outputw-1). 1394 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.19 Post Processor Red Channel Mask Register Name: VDEC_REDMR Access: Read/Write 31 30 29 28 27 26 25 24 MASK 23 22 21 20 19 18 17 16 MASK 15 14 13 12 11 10 9 8 MASK 7 6 5 4 3 2 1 0 MASK • MASK: Bit Mask for R Component (and Alpha Channel) SAM9M11 [DATASHEET] 1395 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.20 Post Processor Green Channel Mask Register Name: VDEC_GREMR Access: Read/Write 31 30 29 28 27 26 25 24 MASK 23 22 21 20 19 18 17 16 MASK 15 14 13 12 11 10 9 8 MASK 7 6 5 4 3 2 1 0 MASK • MASK: Bit Mask for G Component (and Alpha Channel) 1396 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.21 Post Processor Blue Channel Mask Register Name: VDEC_BLUMR Access: Read/Write 31 30 29 28 27 26 25 24 MASK 23 22 21 20 19 18 17 16 MASK 15 14 13 12 11 10 9 8 MASK 7 6 5 4 3 2 1 0 MASK • MASK: Bit Mask for B Component (and Alpha Channel) SAM9M11 [DATASHEET] 1397 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.22 Post Processor Control Register Name: VDEC_CTLR Access: Read/Write 31 30 29 28 27 26 25 24 IN_FORMAT OUT_FORMAT OUT_H 23 22 21 20 19 18 17 16 OUT_H 15 14 13 12 11 10 9 8 OUT_H OUT_W 7 6 5 4 3 2 1 0 OUT_W – – CROP8_R_EN CROP8_D_EN • CROP8_D_EN: Crop 8 Down Pixel PP input picture height is not 16 pixels multiple. Only 8 pixel rows of the most down MB of the unrotated input picture is used for PP input. • CROP8_D_EN: Crop 8 Right Pixel PP input picture width is not 16 pixels multiple. Only 8 pixels of the most right MB of the unrotated input picture is used for PP input. • OUT_W: Scaled Picture Width in Pixels Must be dividable by 8. Max scaled picture width is 1920 pixels or maximum three times the input source width minus 8pixels. • OUT_H: Scaled Picture Height in Pixels Must be dividable by 2. Max scaled picture height is 1920 pixels or maximum three times the input source height minus 8pixels. • OUT_FORMAT: PP Output Picture Data Format 0: RGB 1: YCbCr 4:2:0 planar (Not supported). 2: YCbCr 4:2:2 planar (Not supported). 3: YUYV 4:2:2 interleaved. 4: YCbCr 4:4:4 planar (Not supported). 5: YCh 4:2:0 chrominance interleaved. 6: YCh 4:2:2 (Not supported). 7: YCh 4:4:4 (Not supported). 1398 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

• IN_FORMAT: PP Input Picture Data Format 0: YUYV 4:2:2 interleaved (supported only in external mode). 1: YCbCr 4:2:0 Semi-planar in linear raster-scan format. 2: YCbCr 4:2:0 planar (supported only in external mode). 3: YCbCr 4:0:0 (supported only in pipelined mode). 4: YCbCr 4:2:2 Semi-planar (supported only in pipelined mode). 5: YCbCr 4:2:0 Semi-planar in tiled format (supported only in external mode). 6: YCbCr 4:4:0 Semi-planar (supported only in pipelined mode, possible for jpeg only). SAM9M11 [DATASHEET] 1399 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.23 Post Processor Mask 1 Start Coordinate Register Name: VDEC_M1STR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – RMV 23 22 21 20 19 18 17 16 MAP_COEFF M1_AB_EN M1_START_Y 15 14 13 12 11 10 9 8 M1_START_Y M1_START_X 7 6 5 4 3 2 1 0 M1_START_X • M1_START_X: Mask 1 X Start Horizontal start pixel for mask area 1. Defines the x coordinate. Coordinate 0, 0 means the up-left corner in PP output lumi- nance picture. • M1_START_Y: Mask 1 Y start Vertical start pixel for mask area 1. Defines the y coordinate. Coordinate 0, 0 means the up-left corner in PP output lumi- nance picture. • M1_AB_EN: Mask 1 Alpha Blending Enable Instead of masking the output picture the alpha blending is performed. Alpha blending source can be found from alpha blend 1 base address. Alpha blending can be enabled only for RGB/YUYV 422 data. • RMV: Range Map Value Range map value for chrominance component (RANGE_MAPUV+9 in VC-1 standard). 1400 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.24 Post Processor Mask 2 Start Coordinate Register Name: VDEC_M2STR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – M2_AB_EN M2_START_Y 15 14 13 12 11 10 9 8 M2_START_Y M2_START_X 7 6 5 4 3 2 1 0 M2_START_X • M2_START_X: Mask 2 X Start Horizontal start pixel for mask area 2. Defines the x coordinate. Coordinate 0,0 means the up-left corner in PP output lumi- nance picture. • M2_START_Y: Mask 2 Y Start Vertical start pixel for mask area 2. Defines the y coordinate. Coordinate 0,0 means the up-left corner in PP output lumi- nance picture. • M2_AB_EN: Mask 2 Alpha Blending Enable Instead of masking the output picture the alpha blending is performed. Alpha blending source can be found from alpha blend 1 base address. Alpha blending can be enabled only for RGB/YUYV 422 data. SAM9M11 [DATASHEET] 1401 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.25 Post Processor Mask 1 Size and PP Original Width Register Name: VDEC_M1SZOWR Access: Read/Write 31 30 29 28 27 26 25 24 PP_ORIG_W 23 22 21 20 19 18 17 16 PP_ORI_W M1_EN M1_END_Y 15 14 13 12 11 10 9 8 M1_END_Y M1_END_X 7 6 5 4 3 2 1 0 M1_END_X • M1_END_X: Mask 1 X End Mask 1 end coordinate x in pixels (inside of PPD output picture). Range must be between [Mask1StartCoordinateX, ScaledWidth]. • M1_END_Y: Mask 1 Y Start Mask 1 end coordinate y in pixels (inside of PPD output picture). Range must be between [Mask1StartCoordinateY, ScaledHeight]. • M1_EN: Mask 1 Enable Mask 1 enable. If mask 1 is used this bit is high. • PP_ORIG_W: PP Input Picture Original Width In macro blocks. 1402 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.26 Post Processor Mask 2 Size Register Name: VDEC_M2SZR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – M2_EN M2_END_Y 15 14 13 12 11 10 9 8 M2_END_Y M2_END_X 7 6 5 4 3 2 1 0 M2_END_X • M2_END_X: Mask 2 X end Mask 2 end coordinate x in pixels (inside of PP output picture). Range must be between [Mask2StartCoordinateX, ScaledWidth]. • M2_START_Y: Mask 2 Y end Mask 2 end coordinate y in pixels (inside of PP output picture). Range must be between [Mask2StartCoordinateY, ScaledHeight]. • M2_EN: Mask 2 enable. If mask 1 is used this bit is high. SAM9M11 [DATASHEET] 1403 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.27 Post Processor Picture-in-Picture Register 0 Name: VDEC_PIPR0 Access: Read/Write 31 30 29 28 27 26 25 24 – – RIGHT_EN LEFT_EN UP_EN DOWN_EN UP_CROSS 23 22 21 20 19 18 17 16 UP_CROSS 15 14 13 12 11 10 9 8 UP_CROSS – – – – DOWN_CROSS 7 6 5 4 3 2 1 0 DOWN_CROSS • DOWN_CROSS: Down Cross Amount of downward overcross (vertical pixels outside of display from the down side). Range must be between [0, ScaledHeight]. • UP_CROSS: Up Cross Amount of upward overcross (vertical pixels outside of display from the upper side). Range must be between [0, ScaledHeight]. • DOWN_EN: Downward overcross enable 0: No downward overcross. 1: Downward overcross. • UP_EN: Upward overcross enable 0: No upward overcross. 1: Upward overcross. • LEFT_EN: Left side overcross enable 0: No left side overcross. 1: Left side overcross. • RIGHT_EN: Right side overcross enable 0: No right side overcross. 1: Right side overcross. 1404 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.28 Post Processor Dithering and Picture-in-Picture Register 1 Name: VDEC_DPIPR1 Access: Read/Write 31 30 29 28 27 26 25 24 DITH_SEL_R DITH_SEL_G DITH_SEL_B – – 23 22 21 20 19 18 17 16 – – RIGHT_CROSS 15 14 13 12 11 10 9 8 RIGHT_CROSS LEFT_CROSS 7 6 5 4 3 2 1 0 LEFT_CROSS • LEFT_CROSS: Left Cross Amount of left side overcross (Horizontal pixels outside of display from the left side). Range must be between [0, ScaledWidth]. • RIGHT_CROSS: Right Cross Amount of right side overcross (Horizontal pixels outside of display from the right side). Range must be between [0, ScaledWidth]. • DITH_SEL_x: Dithering Control for xChannel 0: Dithering disabled. 1: Use four-bit dither matrix. 2: Use five-bit dither matrix. 3: Use six-bit dither matrix. SAM9M11 [DATASHEET] 1405 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.29 Post Processor Display Width Register Name: VDEC_DWR Access: Read/Write 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – DISP_WIDTH 7 6 5 4 3 2 1 0 DISP_WIDTH • DISP_WIDTH: Display Width Width of the display in pixels. Maximum is 1920 (HDTV). 1406 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.30 Post Processor Alpha Blending GUI 1 Component Base Address Name: VDEC_ABGUI1BA Access: Read/Write 31 30 29 28 27 26 25 24 AB_GUI1_BA 23 22 21 20 19 18 17 16 AB_GUI1_BA 15 14 13 12 11 10 9 8 AB_GUI1_BA 7 6 5 4 3 2 1 0 AB_GUI1_BA – – • AB_GUI1_BA: Alpha Blending GUI 1 Base Address Base address for alpha blending input 1 (if mask1 is used in alpha blending mode). Format of data is 24-bit RGB/YCbCr and endian/swap -mode is as in PP input. Amount of data is informed with mask 1 size. SAM9M11 [DATASHEET] 1407 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

48.11.31 Post Processor Alpha Blending GUI 2 Component Base Address Name: VDEC_ABGUI2BA Access: Read/Write 31 30 29 28 27 26 25 24 AB_GUI2_BA 23 22 21 20 19 18 17 16 AB_GUI2_BA 15 14 13 12 11 10 9 8 AB_GUI2_BA 7 6 5 4 3 2 1 0 AB_GUI1_BA – – • AB_GUI2_BA: Alpha Blending GUI 2 Base Address Base address for alpha blending input 2 (if mask2 is used in alpha blending mode). Format of data is 24-bit RGB/YCbCr and endian/swap -mode is as in PP input. Amount of data is informed with mask 2 size. 1408 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

SAM9M11 [DATASHEET] 1409 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49. SAM9M11 Electrical Characteristics 49.1 Absolute Maximum Ratings Table 49-1. Absolute Maximum Ratings* Junction Temperature...................................................125°C *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Storage Temperature.....................................60°C to +150°C This is a stress rating only and functional operation of the device at these or other conditions beyond those Voltage on Input Pins indicated in the operational sections of this specification with Respect to Ground....-0.3V to VDDIO + 0.3V (+4V max) is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reli- Maximum Operating Voltage ability. (VDDCORE, VDDPLLA, VDDUTMIC, VDDPLLUTMI)....1.2V (VDDIOM0).....................................................................2.0V (VDDIOM1, VDDIOPx, VDDUTMII, VDDOSC, VDDANA and VDDBU)...................................................4.0V Total DC Output Current on all I/O lines.....................350 mA 49.2 DC Characteristics The following characteristics are applicable to the operating temperature range: T = -40°C to +85°C, unless otherwise A specified. Table 49-2. DC Characteristics Symbol Parameter Conditions Min Typ Max Unit V DC Supply Core – 0.9 1.0 1.1 V DDCORE V VDDCORE ripple – – – 20 mVrms DDCORErip DC Supply UDPHS and V – 0.9 1.0 1.1 V DDUTMIC UHPHS UTMI+ Core DC Supply UDPHS and V – 3.0 3.3 3.6 V DDUTMII UHPHS UTMI+ Interface V DC Supply Backup – 1.8 – 3.6 V DDBU V VDDBU ripple – – – 30 mVrms DDBUrip V DC Supply PLLA – 0.9 1.0 1.1 V DDPLLA V VDDPLLA ripple – – – 10 mVrms DDPLLArip V DC Supply PLLUTMI – 0.9 1.0 1.1 V DDPLLUTMI V VDDPLLUTMI ripple – – – 10 mVrms DDPLLUTMIrip V DC Supply Oscillator – 1.65 – 3.6 V DDOSC V VDDOSC ripple – – – 30 mVrms DDOSCrip V DC Supply DDR I/Os – 1.65 1.8 1.95 V DDIOM0 V DC Supply EBI I/Os – 1.65/3.0 1.8/3.3 1.95/3.6 V DDIOM1 V DC Supply Peripheral I/Os – 1.65 – 3.6 V DDIOP0 V DC Supply Peripheral I/Os – 1.65 – 3.6 V DDIOP1 1410 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 49-2. DC Characteristics (Continued) Symbol Parameter Conditions Min Typ Max Unit V DC Supply ISI – 1.65 – 3.6 V DDIOP2 V DC Supply Analog – 3.0 3.3 3.6 V DDANA V 3.0–3.6 V -0.3 – 0.8 V DDIO V Input Low-level Voltage IL V 1.65–1.95 V -0.3 – 0.3 × V V DDIO DDIO V 3.0–3.6 V 2 – V + 0.3 V DDIO DDIO V Input High-level Voltage IH V 1.65–1.95 V 0.7 × V – V + 0.3 V DDIO DDIO DDIO I Max, V 3.0–3.6 V – – 0.4 V O DDIO V Output Low-level Voltage CMOS (I < 0.3 mA), V 1.65–1.95 V – – 0.1 V OL O DDIO TTL (I Max), V 1.65–1.95 V – – 0.4 V O DDIO I Max, V 3.0–3.6 V V - 0.4 – – V O DDIO DDIO V Output High-level Voltage CMOS (I < 0.3 mA), V 1.65–1.95 V V - 0.1 – – V OH O DDIO DDIO TTL (I Max), V 1.65–1.95 V V - 0.4 – – V O DDIO DDIO Schmitt trigger Negative IO Max, VDDIO 3.0–3.6 V 0.8 1.1 – V V T- going threshold Voltage TTL (I Max), V 1.65–1.95 V – – 0.3 × V V O DDIO DDIO Schmitt trigger Positive going IO Max, VDDIO 3.0–3.6 V – 1.6 2.0 V V T+ threshold Voltage TTL (I Max), V 1.65–1.95 V 0.3 × V – – V O DDIO DDIO V 3.0–3.6 V 0.5 – 0.75 V DDIO V Schmitt trigger Hysteresis hys V 1.65–1.95 V 0.28 – 0.6 V DDIO PA0–PA31 PB0–PB31 PD0–PD31 PE0–PE31 40 75 190 NTRST and NRST R Pull-up Resistance kΩ PULLUP PC0–PC31 V in 1.8V range 240 – 1000 DDIOM1 PC0–PC31 V in 3.3V range 120 – 350 DDIOM1 PA0–PA31 PB0–PB31 PD0–PD31 – – 8 PE0–PE31 I Output Current mA O PC0–PC31 V in 1.8V range – – 2 DDIOM1 PC0–PC31 V in 3.3V range – – 4 DDIOM1 On V = 1.0V, DDCORE T = 25°C – 30 – A MCK = 0 Hz, excluding POR mA All inputs driven TMS, TDI, T = 85°C – – 120 TCK, NRST = 1 A I Static Current SC On V = 3.3V, DDBU Logic cells consumption, TA = 25°C – 9 – µA excluding POR All inputs driven WKUP=0 T = 85°C – – 25 A SAM9M11 [DATASHEET] 1411 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.3 Power Consumption  Typical power consumption of PLLs, Slow Clock and Main Oscillator  Power consumption of power supply in four different modes: Active, Idle, Ultra Low-power and Backup  Power consumption by peripheral: calculated as the difference in current measurement after having enabled then disabled the corresponding clock 49.3.1 Power Consumption versus Modes The values in Table 49-3 and Table 49-4 are estimated values of the power consumption with operating conditions as follows:  V = 1.8V DDIOM0  V = 3.3V DDIOP0 and 1  V = 1.0V DDPLLA  V = 1.0V DDCORE  VDDBU = 3.3V  TA = 25°C  There is no consumption on the I/Os of the device. Figure 49-1. Measures Schematics VDDBU AMP1 VDDCORE AMP2 These figures represent the power consumption estimated on the power supplies. Table 49-3. Power Consumption for Different Modes Mode Conditions Consumption Unit ARM Core clock is 400 MHz. MCK is 133 MHz. Active All peripheral clocks activated. 130 mA onto AMP2 Idle state, waiting an interrupt. Idle All peripheral clocks de-activated. 55 mA onto AMP2 ARM Core clock is 500 Hz. Ultra low power All peripheral clocks de-activated. 30 mA onto AMP2 Device only V powered DDBU Backup 8 µA onto AMP1 1412 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 49-4. Power Consumption by Peripheral in Active Mode Peripheral Consumption Unit AC97 5.3 AES 4.0 DMA 0.2 EMAC 34.8 HSMCI 25.6 ISI 4.8 LCD 20.4 PIO Controller 2.2 PWM 3.8 SHA 3.0 µA/MHz SPI 4.7 SSC 6.6 Timer Counter Channels 6.9 TRNG 0.9 TSADCC 0.1 TWI 1.3 UDPHS 21.7 UHPHS 53.2 USART 7.2 VDEC decoding H.264 854x480 video on WindowsCE 22.6 49.4 Clock Characteristics 49.4.1 Processor Clock Characteristics Table 49-5. Processor Clock Waveform Parameters Symbol Parameter Conditions Min Max Unit VDDCORE = 0.9V 1/(t ) Processor Clock Frequency 125(1) 400 MHz CPPCK T = 85°C A Note: 1. For DDR2 usage, there are no limitations to LDDDR, SDRAM and mobile SDRAM. 49.4.2 Master Clock Characteristics The master clock is the maximum clock at which the system is able to run. It is given by the smallest value of the internal bus clock and EBI clock. Table 49-6. Master Clock Waveform Parameters Symbol Parameter Conditions Min Max Unit VDDCORE = 0.9V 1/(t ) Master Clock Frequency 125(1) 133 MHz CPMCK T = 85°C A Note: 1. For DDR2 usage, there are no limitations to LDDDR, SDRAM and mobile SDRAM. SAM9M11 [DATASHEET] 1413 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.5 Main Oscillator Characteristics Table 49-7. Main Oscillator Characteristics Symbol Parameter Conditions Min Typ Max Unit 1/(t ) Crystal Oscillator Frequency – 8 12 16 MHz CPMAIN C (1) Crystal Load Capacitance – 15 – 20 pF CRYSTAL C (1) Internal Load Capacitance – – 4 – pF INT C = 15 pF(1) – 22 – pF CRYSTAL C External Load Capacitance LEXT C = 20 pF(1) – 32 – Pf CRYSTAL Duty Cycle – 40 50 60 % t Startup Time – – – 2 ms START I Standby Current Consumption Standby mode – – 1 µA DDSTDBY P Drive Level – – – 150 µW ON @ 8 MHz 0.35 – 0.55 mA I Current Dissipation DD ON @ 16 MHz 0.7 – 1.1 mA Note: 1. The C value is specified by the crystal manufacturer. In our case, C must be between 15 pF and 20 pF. All CRYSTAL CRYSTAL parasitic capacitance, package and board, must be calculated in order to reach 15 pF (minimum targeted load for the oscillator) by taking into account the internal load C . So, to target the minimum oscillator load of 15 pF, external INT capacitance must be: 15 pF - 4 pF = 11 pF which means that 22 pF is the target value (22 pF from XIN to GNDOSC and 22pF from XOUT to GNDOSC). If 20 pF load is targeted, the sum of pad, package, board and external capacitances must be 20 pF - 4 pF = 16 pF which means 32 pF (32 pF from XIN to GNDOSC and 32 pF from XOUT to GNDOSC). Figure 49-2. Main Oscillator Schematics SAM9M11 XIN XOUT GNDOSC C CRYSTAL C C LEXT LEXT 49.5.1 Crystal Oscillator Characteristics The following characteristics are applicable to the operating temperature range T = -40°C to 85°C and worst case A of power supply, unless otherwise specified. Table 49-8. Crystal Characteristics Symbol Parameter Conditions Min Typ Max Unit ESR Equivalent Series Resistor Rs – – – 80 Ω C Motional Capacitance – – – 9 fF m C Shunt Capacitance – – – 7 pF SHUNT 1414 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.5.2 XIN Clock Characteristics Table 49-9. XIN Clock Electrical Characteristics Symbol Parameter Conditions Min Max Unit 1/(t ) XIN Clock Frequency – – 50 MHz CPXIN t XIN Clock Period – 20 – ns CPXIN t XIN Clock High Half-period – 0.4 × t 0.6 × t ns CHXIN CPXIN CPXIN t XIN Clock Low Half-period – 0.4 × t 0.6 × t ns CLXIN CPXIN CPXIN C XIN Input Capacitance Main oscillator in Bypass mode, i.e., when – 25 pF IN CKGR_MOR.MOSCEN = 0 and R XIN Pulldown Resistor – 500 kΩ IN CKGR_MOR.OSCBYPASS =1.(see Section 25.12.8 “PMC Clock Generator Main Oscillator V XIN Voltage V V V IN Register”) DDOSC DDOSC 49.6 32 kHz Oscillator Characteristics Table 49-10. 32 kHz Oscillator Characteristics Symbol Parameter Conditions Min Typ Max Unit 1/(t ) Crystal Oscillator Frequency – – 32.768 – kHz CP32KHz C Load Capacitance Crystal @ 32.768 kHz 6 – 12.5 pF CRYSTAL32 C = 6 pF – 6 – pF C (2) External Load Capacitance CRYSTAL32 LEXT32 C = 12.5 pF – 19 – pF CRYSTAL32 Duty Cycle – 40 – 60 % C = 6 pF – – 400 ms R = 50 kΩ(1) CRYSTAL32 S C = 12.5 pF – – 900 ms CRYSTAL32 t Startup Time START C = 6 pF – – 600 ms R = 100 kΩ(1) CRYSTAL32 S C = 12.5 pF – – 1200 ms CRYSTAL32 Notes: 1. R is the equivalent series resistance. S 2. C is determined by taking into account internal, parasitic and package load capacitance. LEXT32 Figure 49-3. 32 kHz Oscillator Schematics SAM9M11 XIN32 XOUT32 GNDBU C CRYSTAL32 C C LEXT32 LEXT32 SAM9M11 [DATASHEET] 1415 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.6.1 32 kHz Crystal Characteristics Table 49-11. 32 kHz Crystal Characteristics Symbol Parameter Conditions Min Typ Max Unit ESR Equivalent Series Resistor Rs Crystal @ 32.768 kHz – 50 100 kΩ C Motional Capacitance Crystal @ 32.768 kHz – – 3 fF m C Shunt Capacitance Crystal @ 32.768 kHz – – 2 pF SHUNT 49.6.2 XIN32 Clock Characteristics Table 49-12. XIN32 Clock Electrical Characteristics Symbol Parameter Conditions Min Max Unit 1/(t ) XIN32 Clock Frequency – – 44 kHz CPXIN32 t XIN32 Clock Period – 22 – µs CPXIN32 t XIN32 Clock High Half-period – 11 – µs CHXIN32 t XIN32 Clock Low Half-period – 11 – µs CLXIN32 t XIN32 Clock Rise time – 400 – ns CLCH32 t XIN32 Clock Fall time – 400 – ns CLCL32 C XIN32 Input Capacitance – 6 pF IN32 32.768 kHz oscillator in Bypass mode, i.e., R XIN32 Pulldown Resistor when RCEN = 0, OSC32EN = 0, – 4 MΩ IN32 OSC32BYP = 1 and OSCSEL = 1 in Slow V XIN32 Voltage V V V IN32 Clock Controller Configuration Register DDBU DDBU V XIN32 Input Low Level Voltage (SCKCR). See Section 24.5 “Slow Clock -0.3 0.3 × V V INIL32 DDBU Selection”. V XIN32 Input High Level Voltage 0.7 × V V + 0.3 V INIH32 DDBU DDBU 49.7 32 kHz RC Oscillator Characteristics Table 49-13. RC Oscillator Characteristics Symbol Parameter Conditions Min Typ Max Unit 1/(t ) Crystal Oscillator Frequency – 22 – 42 kHz CPRCz – Duty Cycle – 45 – 55 % t Startup Time – – – 75 µs START 49.8 PLL Characteristics Table 49-14. PLLA Characteristics Symbol Parameter Conditions Min Typ Max Unit f Output Frequency Refer to following table 400 – 800 MHz OUT f Input Frequency – 2 – 32 MHz IN Active mode – 7 9 mA I Current Consumption PLL Standby mode – – 1 µA t Startup Time – – – 50 µs START 1416 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

The following configuration of fields PMC_PLLICPR.ICPLLA and CKGR_PLLAR.OUTA must be done for each PLLA frequency range. Table 49-15. PLLA Frequency Configuration PLL Frequency Range (MHz) PMC_PLLICPR.ICPLLA CKGR_PLLAR.OUTA 745–800 0 00 695–750 0 01 645–700 0 10 595–650 0 11 545–600 1 00 495–550 1 01 445–500 1 10 400–450 1 11 49.8.1 UTMI PLL Characteristics Table 49-16. Phase Lock Loop Characteristics Symbol Parameter Conditions Min Typ Max Unit f Input Frequency – 4 12 32 MHz IN f Output Frequency – 450 480 600 MHz OUT Active mode – 5 8 mA I Current Consumption PLL Standby mode – – 1.5 µA t Startup Time – – – 50 µs START 49.9 I/Os Criteria used to define the maximum frequency of the I/Os:  Output duty cycle (40%–60%)  Minimum output swing: 100 mV to VDDIO - 100 mV  Addition of rising and falling time inferior to 75% of the period Table 49-17. I/O Characteristics Symbol Parameter Conditions Min Max Unit Max. external load = 20pF 66 3.3V domain (1) – Max. external load = 40pF 34 f VDDIOP-powered pins frequency MHz max Max. external load = 20pF 35 1.8V domain (2) – Max. external load = 40pF 18 Notes: 1. V from 3.0V to 3.6V DDIOP 2. V from 1.65V to 1.95V DDIOP SAM9M11 [DATASHEET] 1417 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.10 USB HS Characteristics 49.10.1USB HS Electrical Characteristics Table 49-18. USB HS Electrical Parameters Symbol Parameter Conditions Min Typ Max Unit R Bus Pull-up Resistor on Upstream Port (idle bus) In LS or FS Mode – 1.5 – kΩ PUI R Bus Pull-up Resistor on Upstream Port (upstream port receiving) In LS or FS Mode – 15 – kΩ PUA t Bias settling time – – – 20 µs BIAS t Oscillator settling time With Crystal 12 MHz – – 2 ms OSC t Settling time f = 12 MHz – 0.3 0.5 ms SETTLING IN 49.10.2Static Power Consumption Table 49-19. Static Power Consumption Symbol Parameter Conditions Min Typ Max Unit I Bias current consumption on VBG – – – 1 µA BIAS HS Transceiver and I/O current consumption – – – 8 µA I VDDUTMII LS / FS Transceiver and I/O current consumption No connection(1) – – 3 µA I Core, PLL, and Oscillator current consumption – – – 2 µA VDDUTMIC Note: 1. If cable is connected add 200 µA (typical) due to Pull-up/Pull-down current consumption. 49.10.3Dynamic Power Consumption Table 49-20. Dynamic Power Consumption Symbol Parameter Conditions Min Typ Max Unit I Bias current consumption on VBG – – 0.7 0.8 mA BIAS HS Transceiver current consumption HS transmission – 47 60 mA HS Transceiver current consumption HS reception – 18 27 mA I LS / FS Transceiver current consumption FS transmission 0m cable (1) – 4 6 mA VDDUTMII LS / FS Transceiver current consumption FS transmission 5m cable (1) – 26 30 mA LS / FS Transceiver current consumption FS reception(1) – 3 4.5 mA I PLL, Core and Oscillator current consumption – – 5.5 9 mA VDDUTMIC Note: 1. Including 1 mA due to Pull-up/Pull-down current consumption. 1418 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.11 Touchscreen ADC Controller (TSADCC) Table 49-21. Channel Conversion Time and ADC Clock Parameter Conditions Min Typ Max Unit ADC Clock Frequency 10-bit resolution mode – – 13.2 MHz Startup Time Return from Idle Mode – – 40 µs Track and Hold Acquisition Time (TTH) ADC Clock = 13.2 MHz(1) 0.5 – – µs Conversion Time (TCT) ADC Clock = 13.2 MHz(1) – – 1.75 µs Throughput Rate ADC Clock = 13.2 MHz(1) – – 440 ksps Note: 1. The Track and Hold Acquisition Time is given by: TTH (ns) = 500+(0.12×Z )(Ω) IN The ADC internal clock is divided by 2 in order to generate a clock with a duty cycle of 75%. So the maximum conversion time is give by: 23 TCT(µs) = --------(MHz) f clk The full speed is obtained for an input source impedance of < 50 ohms maximum, or TTH = 500 ns. To achieve optimal performance of the TSADC, the SHTIM field in TSADCC Mode Register is to be calculated according to this Track and Hold Acquisition Time, also called Sampled and Hold Time. Table 49-22. External Voltage Reference Input Parameter Conditions Min Typ Max Unit TSADVREF Input Voltage Range – 2.4 – V V DDANA TSADVREF Average Current – – 600 µA Current Consumption on VDDANA – – 300 µA Table 49-23. Analog Inputs Parameter Min Typ Max Unit Input Voltage Range 0 – ADVREF V Input Leakage Current – – 1 µA Input Capacitance – 7 10 pF Input Source Impedance – 50 – Ω Table 49-24. Transfer Characteristics Symbol Parameter Min Typ Max Unit Resolution – 10 bit INL Integral Non-linearity – – ±2 LSB DNL Differential Non-linearity -0.9 – +0.9 LSB E Offset Error -1.5 0.5 ±10 mV O E Gain Error – – ±2 LSB G SAM9M11 [DATASHEET] 1419 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.12 Core Power Supply POR Characteristics Table 49-25. Power-On-Reset Characteristics Symbol Parameter Conditions Min Typ Max Unit V Threshold Voltage Rising Minimum Slope of +2.0V/30ms 0.5 0.7 0.89 V T+ V Threshold Voltage Falling – 0.4 0.6 0.85 V T- t Reset Time – 30 70 130 µs RST Table 49-26. Power-down Timing Specification Symbol Parameter Conditions Min Max Unit t Reset Delay at Power-down From NRST low to the first supply turn-off 0 – V RSTPD 49.13 SMC Timings 49.13.1Timing Conditions SMC Timings are given for MAX corners. Timings are given assuming a capacitance load on data, control and address pads as defined in Table 49-27. Table 49-27. Capacitance Load Corner VDDIOM Supply Max Min 3.3V 50 pF 5 pF 1.8V 30 pF 5 pF In the following tables, t is MCK period. CPMCK 49.13.2Timing Extraction 49.13.2.1 Zero Hold Mode Restrictions Table 49-28. Zero Hold Mode Use Maximum System Clock Frequency (MCK) Min Symbol Parameter 1.8V VDDIOM Supply 3.3V VDDIOM Supply Unit f MCK Frequency 66 66 MHz max 1420 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.13.2.2 Read Timings Table 49-29. SMC Read Signals - NRD Controlled (READ_MODE = 1) Min Symbol Parameter 1.8V VDDIOM Supply 3.3V VDDIOM Supply Unit NO HOLD SETTINGS (nrd hold = 0) SMC Data Setup before NRD High 12.0 11.2 ns 1 SMC Data Hold after NRD High 0 0 ns 2 HOLD SETTINGS (nrd hold ≠ 0) SMC Data Setup before NRD High 8.7 8.2 ns 3 SMC Data Hold after NRD High 0 0 ns 4 HOLD or NO HOLD SETTINGS (nrd hold ≠ 0, nrd hold = 0) NBS0/A0, NBS1, NBS2/A1, NBS3, A2–A25 (nrd setup + nrd pulse) × t (nrd setup + nrd pulse) × t SMC CPMCK CPMCK ns 5 Valid before NRD High - 15.4 - 15.5 (nrd setup + nrd pulse - ncs rd (nrd setup + nrd pulse - ncs rd SMC NCS low before NRD High ns 6 setup) × t - 14.7 setup) × t - 14.7 CPMCK CPMCK SMC NRD Pulse Width nrd pulse × t - 0.5 nrd pulse × t - 0.2 ns 7 CPMCK CPMCK Table 49-30. SMC Read Signals - NCS Controlled (READ_MODE = 0) Min Symbol Parameter 1.8V VDDIOM Supply 3.3V VDDIOM Supply Unit NO HOLD SETTINGS (ncs rd hold = 0) SMC Data Setup before NCS High 15.0 14.1 ns 8 SMC Data Hold after NCS High 0 0 ns 9 HOLD SETTINGS (ncs rd hold ≠ 0) SMC Data Setup before NCS High 11.4 10.9 ns 10 SMC Data Hold after NCS High 0 0 ns 11 HOLD or NO HOLD SETTINGS (ncs rd hold ≠ 0, ncs rd hold = 0) NBS0/A0, NBS1, NBS2/A1, NBS3, A2–A25 (ncs rd setup + ncs rd pulse) × (ncs rd setup + ncs rd pulse) × SMC ns 12 valid before NCS High t - 3.7 t - 4.4 CPMCK CPMCK (ncs rd setup + ncs rd pulse - (ncs rd setup + ncs rd pulse - SMC NRD low before NCS High ns 13 nrd setup) × t - 0.8 nrd setup) × t - 1.1 CPMCK CPMCK ncs rd pulse length × t - ncs rd pulse length × t - SMC NCS Pulse Width CPMCK CPMCK ns 14 0.5 0.2 SAM9M11 [DATASHEET] 1421 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.13.2.3 Write Timings Table 49-31. SMC Write Signals - NWE Controlled (WRITE_MODE = 1) Min Symbol Parameter 1.8V VDDIOM Supply 3.3V VDDIOM Supply Unit HOLD or NO HOLD SETTINGS (nwe hold ≠ 0, nwe hold = 0) SMC Data Out Valid before NWE High nwe pulse × t - 2.9 nwe pulse × t - 3.6 ns 15 CPMCK CPMCK SMC NWE Pulse Width nwe pulse × t - 0.7 nwe pulse × t - 0.3 ns 16 CPMCK CPMCK NBS0/A0 NBS1, NBS2/A1, NBS3, A2–A25 SMC nwe setup × t - 3.3 nwe setup × t - 4.1 ns 17 valid before NWE low CPMCK CPMCK (nwe setup - ncs wr setup + nwe (nwe setup - ncs wr setup + nwe SMC NCS low before NWE high ns 18 pulse) × t - 3.1 pulse) × t - 3.4 CPMCK CPMCK HOLD SETTINGS (nwe hold ≠ 0) NWE High to Data OUT, NBS0/A0 NBS1, SMC nwe hold × t - 4.0 nwe hold × t - 4.6 ns 19 NBS2/A1, NBS3, A2–A25 change CPMCK CPMCK (nwe hold - ncs wr hold) × (nwe hold - ncs wr hold) × SMC NWE High to NCS Inactive(1) ns 20 t - 3.2 t - 4.0 CPMCK CPMCK NO HOLD SETTINGS (nwe hold = 0) NWE High to Data OUT, NBS0/A0 NBS1, SMC 1.6 1.4 ns 21 NBS2/A1, NBS3, A2–A25, NCS change(1) Notes: 1. hold length = total cycle duration - setup duration - pulse duration. “hold length” is for “ncs wr hold length” or “NWE hold length”. Table 49-32. SMC Write NCS Controlled (WRITE_MODE = 0) Min Symbol Parameter 1.8V VDDIOM Supply 3.3V VDDIOM Supply Unit SMC Data Out Valid before NCS High ncs wr pulse × t - 2.8 ncs wr pulse × t - 3.5 ns 22 CPMCK CPMCK SMC NCS Pulse Width ncs wr pulse × t - 0.5 ncs wr pulse × t - 0.2 ns 23 CPMCK CPMCK NBS0/A0 NBS1, NBS2/A1, NBS3, A2–A25 SMC ncs wr setup × t - 3.3 ncs wr setup × t - 4.1 ns 24 valid before NCS low CPMCK CPMCK (ncs wr setup - nwe setup + ncs (ncs wr setup - nwe setup + ncs SMC NWE low before NCS high ns 25 pulse) × t - 2.4 pulse) × t - 2.7 CPMCK CPMCK NCS High to Data Out, NBS0/A0, NBS1, SMC ncs wr hold × t - 4.1 ncs wr hold × t - 4.6 ns 26 NBS2/A1, NBS3, A2–A25, change CPMCK CPMCK (ncs wr hold - nwe hold) × (ncs wr hold - nwe hold) × SMC NCS High to NWE Inactive ns 27 t - 2.0 t - 2.8 CPMCK CPMCK 1422 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 49-4. SMC Timings - NCS Controlled Read and Write SMC12 SMC12 SMC24 SMC26 A0/A1/NBS[3:0]/A2–A25 SMC13 SMC13 NRD NCS SMC14 SMC14 SMC23 SMC8 SMC9 SMC10 SMC11 SMC22 SMC26 D0–D15 SMC25 SMC27 NWE NCS Controlled READ NCS Controlled READ NCS Controlled WRITE with NO HOLD with HOLD Figure 49-5. SMC Timings - NRD Controlled Read and NWE Controlled Write SMC5 SMC17 SMC21 SMC5 SMC17 SMC19 A0/A1/NBS[3:0]/A2–A25 SMC6 SMC18 SMC21SMC6 SMC18 SMC20 NCS NRD SMC7 SMC7 SMC1 SMC2 SMC15 SMC21 SMC3 SMC4 SMC15 SMC19 D0–D31 NWE SMC16 SMC16 NRD Controlled READ NWE Controlled WRITE NRD Controlled READ NWE Controlled WRITE with NO HOLD with NO HOLD with HOLD with HOLD SAM9M11 [DATASHEET] 1423 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.14 DDRSDRC Timings The DDRSDRC controller satisfies the timings of standard DDR2, LPDDR, SDR and LPSDR modules. DDR2, LPDDR and SDR timings are specified by the JEDEC standard. Supported speed grade limitations:  DDR2-400 limited at 133 MHz clock frequency (1.8V, 30 pF on data/control, 10 pF on CK/CK#)  LPDDR (1.8V, 30 pF on data/control, 10 pF on CK) ̶ t = 5.0 ns, f = 125 MHz a max ̶ t = 6.0 ns, f = 110 MHz a max ̶ t = 7.5 ns, f = 95 MHz a max  SDR-100 (3.3V, 50 pF on data/control, 10 pF on CK)  SDR-133 (3.3V, 50 pF on data/control, 10 pF on CK)  LPSDR-133 (1.8V, 30 pF on data/control, 10 pF on CK) 49.15 Peripheral Timings 49.15.1SPI 49.15.1.1 Maximum SPI Frequency The following formulas give maximum SPI frequency in Master read and write modes and in Slave read and write modes. Master Write Mode The SPI is only sending data to a slave device such as an LCD, for example. The limit is given by SPI (or 2 SPI ) timing. Since it gives a maximum frequency above the maximum pad speed (see Section 49.9 “I/Os”), 5 the max SPI frequency is the one from the pad. Master Read Mode 1 f Max = --------------------------------------------------------- SPCK SPI (orSPI )+t 0 3 valid t is the slave time response to output data after deleting an SPCK edge. For a non-volatile memory with valid t (or t ) = 12 ns Max, f Max = 38.5 MHz @ V = 3.3V. valid v SPCK DDIO Slave Read Mode In slave mode, SPCK is the input clock for the SPI. The max SPCK frequency is given by setup and hold timings SPI /SPI (or SPI /SPI ). Since this gives a frequency well above the pad limit, the limit in slave 7 8 10 11 read mode is given by SPCK pad. Slave Write Mode 1 f Max = ----------------------------------------------------------- SPCK SPI (orSPI )+t 6 9 setup For 3.3V I/O domain and SPI6, f Max = 33 MHz. t is the setup time from the master before sampling SPCK setup data. 1424 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.15.1.2 Timing Conditions Timings are given assuming a capacitance load on MISO, SPCK and MOSI as defined in Table 49-33. Table 49-33. Capacitance Load for MISO, SPCK and MOSI (product dependent) Corner Supply Max Min 3.3V 40 pF 5 pF 1.8V 20 pF 5 pF 49.15.1.3 Timing Extraction In Figure 49-7 “SPI Master Mode 1 and 2” and Figure 49-8 “SPI Master Mode 0 and 3”, the MOSI line shifting edge is represented with a hold time = 0. However, it is important to note that for this device, the MISO line is sampled prior to the MOSI line shifting edge. As shown in Figure 49-6 “MISO Capture in Master Mode”, the device sampling point extends the propagation delay (tp) for slave and routing delays to more than half the SPI clock period, whereas the common sampling point allows only less than half the SPI clock period. As an example, an SPI Slave working in Mode 0 is safely driven if the SPI Master is configured in Mode 0. Figure 49-6. MISO Capture in Master Mode 0 < delay < SPI or SPI 0 3 SPCK (generated by the master) MISO Bit N Bit N+1 (slave answer) MISO cannot be provided t p before the edge Common sampling point Device sampling point Safe margin, always > 0 Extended t Internal p shift register Bit N Figure 49-7. SPI Master Mode 1 and 2 SPCK SPI0 SPI1 MISO SPI2 MOSI SAM9M11 [DATASHEET] 1425 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 49-8. SPI Master Mode 0 and 3 SPCK SPI3 SPI4 MISO SPI 5 MOSI Figure 49-9. SPI Slave Mode 0 and 3 NPCS0 SPI12 SPI13 SPCK SPI 6 MISO SPI SPI 7 8 MOSI Figure 49-10. SPI Slave Mode 1 and 2 NPCS0 SPI 13 SPI 12 SPCK SPI 9 MISO SPI SPI 10 11 MOSI 1426 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 49-11. SPI Slave Mode - NPCS Timings SPI14 SPI6 SPI15 SPCK (CPOL = 0) SPI12 SPI9 SPI13 SPCK (CPOL = 1) SPI 16 MISO Table 49-34. SPI Timings with 3.3V Peripheral Supply Symbol Parameter Conditions Min Max Unit SPI SPI Clock – 66 MHz SPCK SPI MISO Setup time before SPCK rises 14.6 – ns 0 SPI MISO Hold time after SPCK rises 0 – ns 1 SPI SPCK rising to MOSI Master Mode 0 0.2 ns 2 SPI MISO Setup time before SPCK falls 14.3 – ns 3 SPI MISO Hold time after SPCK falls 0 – ns 4 SPI SPCK falling to MOSI 0 0.6 ns 5 SPI SPCK falling to MISO 4.6 15.1 ns 6 SPI MOSI Setup time before SPCK rises 0.7 – ns 7 SPI MOSI Hold time after SPCK rises 1.9 – ns 8 SPI SPCK rising to MISO 4.6 15.2 ns 9 SPI MOSI Setup time before SPCK falls 0.9 – ns 10 SPI MOSI Hold time after SPCK falls Slave Mode 1.4 – ns 11 SPI NPCS0 setup to SPCK rising 17.3 – ns 12 SPI NPCS0 hold after SPCK falling 15.1 – ns 13 SPI NPCS0 setup to SPCK falling 18 – ns 14 SPI NPCS0 hold after SPCK rising 15.0 – ns 15 SPI NPCS0 falling to MISO valid 4.4 14.5 ns 16 SAM9M11 [DATASHEET] 1427 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 49-35. SPI Timings with 1.8V Peripheral Supply Symbol Parameter Conditions Min Max Unit SPI SPI Clock – 66 MHz SPCK SPI MISO Setup time before SPCK rises 18.0 – ns 0 SPI MISO Hold time after SPCK rises 0 – ns 1 SPI SPCK rising to MOSI Master Mode 0 0.2 ns 2 SPI MISO Setup time before SPCK falls 17.6 – ns 3 SPI MISO Hold time after SPCK falls 0 – ns 4 SPI SPCK falling to MOSI 0 0.7 ns 5 SPI SPCK falling to MISO 6.0 18.9 ns 6 SPI MOSI Setup time before SPCK rises 0.7 – ns 7 SPI MOSI Hold time after SPCK rises 1.7 – ns 8 SPI SPCK rising to MISO 5.5 18.7 ns 9 SPI MOSI Setup time before SPCK falls 0.5 – ns 10 SPI MOSI Hold time after SPCK falls Slave Mode 1.4 – ns 11 SPI NPCS0 setup to SPCK rising 17.4 – ns 12 SPI NPCS0 hold after SPCK falling 15.5 – ns 13 SPI NPCS0 setup to SPCK falling 17.8 – ns 14 SPI NPCS0 hold after SPCK rising 15.3 – ns 15 SPI NPCS0 falling to MISO valid 5.4 17.7 ns 16 Figure 49-12. Min and Max Access Time for SPI Output Signal SPCK SPI0 SPI1 MISO SPI2max MOSI SPI2min 1428 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.15.2SSC 49.15.2.1 Timing Conditions Timings are given assuming a capacitance load as defined in Table 49-36. Table 49-36. Capacitance Load Corner Supply Max Min 3.3V 30 pF 0 pF 1.8V 20 pF 0 pF 49.15.2.2 Timing Extraction Figure 49-13. SSC Transmitter, TK and TF in Output TK (CKI =0) TK (CKI =1) SSC0 TF/TD Figure 49-14. SSC Transmitter, TK in Input and TF in Output TK (CKI =0) TK (CKI =1) SSC1 TF/TD SAM9M11 [DATASHEET] 1429 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 49-15. SSC Transmitter, TK in Output and TF in Input TK (CKI=0) TK (CKI=1) SSC2 SSC3 TF SSC4 TD Figure 49-16. SSC Receiver RK and RF in Input RK (CKI=0) RK (CKI=1) SSC8 SSC9 RF/RD Figure 49-17. SSC Receiver, RK in Input and RF in Output RK (CKI=1) RK (CKI=0) SSC8 SSC9 RD SSC10 RF Figure 49-18. SSC Receiver, RK and RF in Output RK (CKI=1) RK (CKI=0) SSC11 SSC12 RD SSC13 RF 1430 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Figure 49-19. SSC Receiver, RK in Output and RF in Input RK (CKI=0) RK (CKI=1) SSC11 SSC12 RF/RD Table 49-37. SSC Timings with 3.3V Peripheral Supply Symbol Parameter Conditions Min Max Unit Transmitter SSC TK edge to TF/TD (TK output, TF output) – 0(1) 4.0(1) ns 0 SSC TK edge to TF/TD (TK input, TF output) – 3.7(1) 13.6(1) ns 1 SSC TF setup time before TK edge (TK output) – 14.3 - t – ns 2 CPMCK SSC TF hold time after TK edge (TK output) – t - 3.9 – ns 3 CPMCK – -2.6(1) 4.0(1) SSC4 TK edge to TF/TD (TK output, TF input) STTDLY = 0 -2.6 + (2 × t )(1) 4.0 + (2 × t )(1) ns START = 4, 5 or 7 CPMCK CPMCK SSC TF setup time before TK edge (TK input) – 0 – ns 5 SSC TF hold time after TK edge (TK input) – t – ns 6 CPMCK – 3.8(1) 13.6(1) SSC7 TK edge to TF/TD (TK input, TF input) STTDLY = 0 3.8 + (3 × t )(1) 13.6 + (3 × t )(1) ns START = 4, 5 or 7 CPMCK CPMCK Receiver SSC RF/RD setup time before RK edge (RK input) – 1.9 – ns 8 SSC RF/RD hold time after RK edge (RK input) – t – ns 9 CPMCK SSC RK edge to RF (RK input) – 4.3(1) 16.9(1) ns 10 RF/RD setup time before RK edge (RK SSC – 14.2 - t – ns 11 output) CPMCK SSC RF/RD hold time after RK edge (RK output) – t - 3.9 – ns 12 CPMCK SSC RK edge to RF (RK output) – 0(1) 5.2(1) ns 13 Notes: 1. For output signals (TF, TD, RF), Min and Max access times are defined. The Min access time is the time between the TK (or RK) edge and the signal change. The Max access time is the time between the TK edge and the signal stabilization. Figure 49-20 illustrates Min and Max accesses for SSC . The same applies to SSC , SSC , and SSC , SSC and SSC . 0 1 4 7 10 13 SAM9M11 [DATASHEET] 1431 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 49-38. SSC Timings with 1.8V Peripheral Supply Symbol Parameter Conditions Min Max Unit Transmitter SSC TK edge to TF/TD (TK output, TF output) – 0(1) 4.2(1) ns 0 SSC TK edge to TF/TD (TK input, TF output) – 4.8(1) 18.4(1) ns 1 SSC TF setup time before TK edge (TK output) – 18.4 - t – ns 2 CPMCK SSC TF hold time after TK edge (TK output) – t - 5.1 – ns 3 CPMCK – 2.8(1) 4.2(1) SSC4 TK edge to TF/TD (TK output, TF input) STTDLY = 0 -2.8 + (2 × t )(1) 4.2 + (2 × t )(1) ns START = 4, 5 or 7 CPMCK CPMCK SSC TF setup time before TK edge (TK input) – 0.6 – ns 5 SSC TF hold time after TK edge (TK input) – t – ns 6 CPMCK – 5.0(1) 18.3(1) SSC7 TK edge to TF/TD (TK input, TF input) STTDLY = 0 5.0 + (3 × t )(1) 18.3 + (3 Unit ns START = 4, 5 or 7 CPMCK t )(1) CPMCK Receiver SSC RF/RD setup time before RK edge (RK input) – 2.4 – ns 8 SSC RF/RD hold time after RK edge (RK input) – t – ns 9 CPMCK SSC RK edge to RF (RK input) – 5.4(1) 21.5(1) ns 10 RF/RD setup time before RK edge (RK SSC – 18.6 - t – ns 11 output) CPMCK SSC RF/RD hold time after RK edge (RK output) – t - 5.1 – ns 12 CPMCK SSC RK edge to RF (RK output) – 0(1) 5.3(1) ns 13 Notes: 1. For output signals (TF, TD, RF), Min and Max access times are defined. The Min access time is the time between the TK (or RK) edge and the signal change. The Max access time is the time between the TK edge and the signal stabilization. Figure 49-20 illustrates Min and Max accesses for SSC . The same applies to SSC , SSC , and SSC , SSC and SSC . 0 1 4 7 10 13 Figure 49-20. Min and Max Access Time of Output Signals TK (CKI = 1) TK (CKI = 0) SSC0min SSC0max TF/TD 1432 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.15.3ISI 49.15.3.1 Timing Conditions Timings are given assuming capacitance loads as defined in Table 49-39. Table 49-39. Capacitance Load Corner Supply Max Min 3.3V 30 pF 0 pF 1.8V 20 pF 0 pF 49.15.3.2 Timing Extraction Figure 49-21. ISI Timing Diagram PIXCLK ISI 3 DATA[7:0] Valid Data Valid Data Valid Data VSYNC HSYNC ISI ISI 1 2 Table 49-40. ISI Timings with 3.3V Peripheral Supply Symbol Parameter Min Max Unit ISI DATA/VSYNC/HSYNC setup time 1.1 – ns 1 ISI DATA/VSYNC/HSYNC hold time 2.0 – ns 2 ISI PIXCLK frequency – 80 MHz 3 Table 49-41. ISI Timings with 1.8V Peripheral Supply Symbol Parameter Min Max Unit ISI DATA/VSYNC/HSYNC setup time 1.1 – ns 1 ISI DATA/VSYNC/HSYNC hold time 2.2 – ns 2 ISI PIXCLK frequency – 80 MHz 3 49.15.4HSMCI The High Speed MultiMedia Card Interface (HSMCI) supports the MultiMedia Card (MMC) Specification V4.3, the SD Memory Card Specification V2.0, the SDIO V2.0 specification and CE-ATA V1.1. SAM9M11 [DATASHEET] 1433 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.15.5EMAC 49.15.5.1 Timing Conditions Timings are given assuming a capacitance load on data and clock as defined in Table 49-42. Table 49-42. Capacitance Load on Data, Clock Pads Corner Supply Max Min 3.3V 20 pF 0 pF 1.8V 20 pF 0 pF 49.15.5.2 Timing Constraints The Ethernet controller satisfies the timings of the standards given in Table 49-43, Table 49-44 and Table 49-45. Table 49-43. EMAC Signals Relative to EMDC Symbol Parameter Min Max Unit EMAC Setup for EMDIO from EMDC rising 13.5 ns 1 EMAC Hold for EMDIO from EMDC rising 10 ns 2 EMAC EMDIO toggling from EMDC falling 0 (1) 2 (1) ns 3 Notes: 1. For EMAC output signals, Min and Max access time are defined. The Min access time is the time between the EMDC falling edge and the signal change. The Max access time is the time between the EMDC falling edge and the signal stabilization. Figure 49-22 illustrates Min and Max accesses for EMAC3. Figure 49-22. Min and Max Access Time of EMAC Output Signals EMDC EMAC1 EMAC2 EMAC3 max EMDIO EMAC EMAC 4 5 EMAC 3 min 49.15.5.3 MII Mode Table 49-44. EMAC MII Specific Signals Symbol Parameter Min Max Unit EMAC Setup for ECOL from ETXCK rising 10 – ns 4 EMAC Hold for ECOL from ETXCK rising 10 – ns 5 EMAC Setup for ECRS from ETXCK rising 10 – ns 6 EMAC Hold for ECRS from ETXCK rising 10 – ns 7 EMAC ETXER toggling from ETXCK rising 3 25 ns 8 EMAC ETXEN toggling from ETXCK rising 4.7 25 ns 9 EMAC ETX toggling from ETXCK rising 3 25 ns 10 EMAC Setup for ERX from ERXCK 10 – ns 11 EMAC Hold for ERX from ERXCK 10 – ns 12 1434 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 49-44. EMAC MII Specific Signals (Continued) Symbol Parameter Min Max Unit EMAC Setup for ERXER from ERXCK 10 – ns 13 EMAC Hold for ERXER from ERXCK 10 – ns 14 EMAC Setup for ERXDV from ERXCK 10 – ns 15 EMAC Hold for ERXDV from ERXCK 10 – ns 16 Figure 49-23. EMAC MII Mode EMDC EMAC EMAC EMAC 3 1 2 EMDIO EMAC EMAC 4 5 ECOL EMAC EMAC 6 7 ECRS ETXCK EMAC 8 ETXER EMAC 9 ETXEN EMAC 10 ETX[3:0] ERXCK EMAC EMAC 11 12 ERX[3:0] EMAC EMAC 13 14 ERXER EMAC EMAC 15 16 ERXDV SAM9M11 [DATASHEET] 1435 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.15.5.4 RMII Mode Table 49-45. RMII Mode Symbol Parameter Min Max Unit EMAC ETXEN toggling from EREFCKrising 2 16 ns 21 EMAC ETX toggling from EREFCK rising 2 16 ns 22 EMAC Setup for ERX from EREFCK rising 4 ns 23 EMAC Hold for ERX from EREFCK rising 2 ns 24 EMAC Setup for ERXER from EREFCK rising 4 ns 25 EMAC Hold for ERXER from EREFCK rising 2 ns 26 EMAC Setup for ECRSDV from EREFCK rising 4 ns 27 Figure 49-24. EMAC RMII Timings EREFCK EMAC 21 ETXEN EMAC 22 ETX[1:0] EMAC EMAC 23 24 ERX[1:0] EMAC EMAC 25 26 ERXER EMAC EMAC 27 28 ECRSDV 49.15.6USART in SPI Mode 49.15.6.1 Timing Conditions Timings are given assuming a capacitance load on MISO, SPCK and MOSI as defined in Table 49-46. Table 49-46. Capacitance Load for MISO, SPCK and MOSI (product dependent) Corner Supply Max Min 3.3V 40 pF 0 pF 1.8V 20 pF 0 pF 1436 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.15.6.2 Timing Extraction Figure 49-25. USART SPI Master Mode NPCSx SPI 5 SPI 3 CPOL = 1 SPI 0 SPCK = 0 CPOL = 0 SPI 4 SPI SPI SPI 4 1 2 MISO MSB LSB MOSI Figure 49-26. USART SPI Slave Mode NPCS0 SPI12 SPI13 SPCK SPI 6 MISO SPI SPI 7 8 MOSI Figure 49-27. SPI Slave Mode - NPCS Timings SPI14 SPI6 SPI15 SPCK (CPOL = 0) SPI12 SPI9 SPI13 SPCK (CPOL = 1) SPI 16 MISO SAM9M11 [DATASHEET] 1437 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 49-47. USART SPI Timings with 3.3V Peripheral Supply Symbol Parameter Conditions Min Max Unit SPI SPCK Period – – ns 0 SPI Input Data Setup Time 17.2 – ns 1 SPI Input Data Hold Time 0 – ns 2 Master Mode SPI Chip Select Active to Serial Clock – 3.5 ns 3 SPI Output Data Setup Time – 0.2 ns 4 SPI Serial Clock to Chip Select Inactive – -0.3 ns 5 SPI SPCK falling to MISO 13.8 (1) 16.9 (1) ns 6 SPI MOSI Setup time before SPCK rises 7.5 – ns 7 SPI MOSI Hold time after SPCK rises 2.9 – ns 8 SPI SPCK rising to MISO 4.7 (1) 17.1 (1) ns 9 SPI MOSI Setup time before SPCK falls 0.4 – ns 10 SPI MOSI Hold time after SPCK falls Slave Mode 0 – ns 11 SPI NPCS0 setup to SPCK rising 10.3 – ns 12 SPI NPCS0 hold after SPCK falling 2.0 – ns 13 SPI NPCS0 setup to SPCK falling 10.7 – ns 14 SPI NPCS0 hold after SPCK rising 2.0 – ns 15 SPI NPCS0 falling to MISO valid – 16.0 ns 16 Notes: 1. For output signals, Min and Max access time must be extracted. The Min access time is the time between the SPCK rising or falling edge and the signal change. The Max access time is the time between the SPCK rising or falling edge and the signal stabilization. Figure 49-11 illustrates Min and Max accesses for SPI . The same applies to SPI , SPI , and SPI . 2 5 6 9 1438 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 49-48. USART SPI Timings with 1.8V Peripheral Supply Symbol Parameter Conditions Min Max Unit SPI SPCK Period – – ns 0 SPI Input Data Setup Time 20.6 – ns 1 SPI Input Data Hold Time 0 – ns 2 Master Mode SPI Chip Select Active to Serial Clock – 6.0 ns 3 SPI Output Data Setup Time – 0.2 ns 4 SPI Serial Clock to Chip Select Inactive – 0 ns 5 SPI SPCK falling to MISO 4.4(1) 20.7(1) ns 6 SPI MOSI Setup time before SPCK rises 7.6 – ns 7 SPI MOSI Hold time after SPCK rises 3.1 – ns 8 SPI SPCK rising to MISO 5.6(1) 20.6(1) ns 9 SPI MOSI Setup time before SPCK falls 0.8 – ns 10 SPI MOSI Hold time after SPCK falls Slave Mode 0 – ns 11 SPI NPCS0 setup to SPCK rising 10.2 – ns 12 SPI NPCS0 hold after SPCK falling 1.9 – ns 13 SPI NPCS0 setup to SPCK falling 11.0 – ns 14 SPI NPCS0 hold after SPCK rising 2.2 – ns 15 SPI NPCS0 falling to MISO valid – 18.9 ns 16 Notes: 1. For output signals, Min and Max access time must be extracted. The Min access time is the time between the SPCK rising or falling edge and the signal change. The Max access time is the time between the SPCK rising or falling edge and the signal stabilization. Figure 49-11 illustrates Min and Max accesses for SPI . The same applies to SPI , SPI , and SPI . 2 5 6 9 SAM9M11 [DATASHEET] 1439 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

50. Mechanical Characteristics 50.1 Package Drawings Figure 50-1. 324-ball TFBGA Package Drawing 1440 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 50-1. Package Information Ball Land 0.375 mm +/- 0.05 Soldering Mask Opening 0.275 mm +/- 0.03 Solder Mask Definition Solder Mask Defined Table 50-2. Device and 324-ball TFBGA Package Maximum Weight 400 mg Table 50-3. 324-ball TFBGA Package Characteristics Moisture Sensitivity Level 3 Table 50-4. Package Reference JEDEC Drawing Reference MO-210 JESD97 Classification e1 This package respects the recommendations of the NEMI User Group. 50.2 Soldering Profile Table 50-5 gives the recommended soldering profile from J-STD-020C. Table 50-5. Soldering Profile Profile Feature Green Package Average Ramp-up Rate (217°C to Peak) 3°C/sec. max. Preheat Temperature 175°C ±25°C 180 sec. max. Temperature Maintained Above 217°C 60 sec. to 150 sec. Time within 5°C of Actual Peak Temperature 20 sec. to 40 sec. Peak Temperature Range 260 +0 °C Ramp-down Rate 6°C/sec. max. Time 25°C to Peak Temperature 8 min. max. Note: It is recommended to apply a soldering temperature higher than 250°C. A maximum of three reflow passes is allowed per component. SAM9M11 [DATASHEET] 1441 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

51. Marking All devices are marked with the Atmel logo and the ordering code. Additional marking may be in one of the following formats: where  “YY”: manufactory year  “WW”: manufactory week  “V”: revision  “XXXXXXXXX”: lot number 1442 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

52. SAM9M11 Ordering Information Table 52-1. SAM9M11 Ordering Information Operating Temperature Ordering Code Package Carrier Type Range Industrial AT91SAM9M11B-CU TFBGA324 Tray -40°C to 85°C SAM9M11 [DATASHEET] 1443 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

53. SAM9M11 Errata 53.1 SAM9M11 Errata - Rev. A Parts 53.1.1 Boot ROM 53.1.1.1 Boot ROM: NAND Flash boot does not support ECC Correction The boot ROM allows booting from block 0 of a NAND Flash connected on CS3. However, the boot ROM does not feature ECC correction on a NAND Flash. Most of the NAND Flash vendors do not guarantee anymore that block 0 is error free. Therefore we advise to locate the bootstrap program into another device supported by the boot ROM (DataFlash, Serial Flash, SDCARD or EEPROM), and to implement a NAND Flash access with ECC. Problem Fix/Workaround None. 53.1.1.2 Boot ROM: Boot issue on AT45-series SPI Dataflash The boot from AT45-series SPI DataFlash is not functional except for the AT45DB321D. Future revisions of the AT45DB321D might not be functional either. Problem Fix/Workaround Use AT25-series Serial Flash instead. 53.1.2 Reset Controller (RSTC) 53.1.2.1 RSTC: Software reset during DDRAM accesses When a software reset (CPU and peripherals) occurs during DDRAM read access, the CPU will stop the DDRAM clock. The DDRAM maintains the data on the bus until the clock restarts. This will create a bus conflict if another memory sharing the external bus with the DDRAM is accessed prior to completion of the read access to the DDRAM. Such a conflict will occur when the device boots out of an external NAND or NOR Flash following the software reset. Problem Fix/Workaround 1. Boot from Serial Flash 2. Before generating the software reset, the user must ensure that all the accesses to DDRAM are completed and then put the DDRAM in self-refresh mode. The routine to generate the software reset must be located in internal SRAM or in the ARM cache memory. 53.1.3 Error Corrected Code Controller (ECC) 53.1.3.1 ECC: Computation with a 1 clock cycle long NRD/NWE pulse If the SMC is programmed with NRD/NWE pulse length equal to 1 clock cycle, ECC cannot compute the parity. Problem Fix/Workaround It is recommended to program SMC with a value superior to 1. 53.1.3.2 ECC: Incomplete parity status when error in ECC parity When a single correctable error is detected in ECC value, the error is located in ECC Parity register's field which contains a 1 in the 24 least significant bits except when the error is located in the 12th or the 24th bit. In this case, these bits are always stuck at 0. A Single correctable error is detected but it is impossible to correct it. Problem Fix/Workaround None. 1444 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

53.1.3.3 ECC: Unsupported ECC per 512 words 1 bit ECC per 512 words is not functional. Problem Fix/Workaround Perform the ECC computation by software. 53.1.3.4 ECC: Unsupported hardware ECC on 16-bit Nand Flash Hardware ECC on 16-bit Nand Flash is not supported. Problem Fix/Workaround Perform the ECC by software. 53.1.4 Static Memory Controller (SMC) 53.1.4.1 SMC Delay: Access In this document, the Access is “Read-write” in the Register Mapping Table (SMC_DELAY1 to SMC_DELAY8 rows), and in the SMC DELAY I/O Register. The current access is “Write-only”. Problem Fix/Workaround None 53.1.5 Pulse Width Modulation Controller (PWM) 53.1.5.1 PWM: Zero Period It is impossible to update a period equal to 0 by using the PWM_CUPD register. Problem Fix/Workaround None 53.1.6 Serial Synchronous Controller (SSC) 53.1.6.1 SSC: Data sent without any frame synchro When SSC is configured with the following conditions:  RF is in input,  TD is synchronized on a receive START (any condition: START field = 2 to 7)  TF toggles at each start of data transfer  Transmit STTDLY = 0  Check TD and TF after a receive START, The data is sent but there is not any toggle of the TF line Problem Fix/Workaround Transmit STTDLY must be different from 0. 53.1.6.2 SSC: Unexpected delay on TD output When SSC is configured with the following conditions:  TCMR.STTDLY more than 0  RCMR.START = Start on falling edge/Start on Rising edge/Start on any edge  RFMR.FSOS = None (input)  TCMR.START = Receive Start Unexpected delay of 2 or 3 system clock cycles is added to TD output. Problem Fix/Workaround None SAM9M11 [DATASHEET] 1445 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

53.1.7 Touch Screen (TSADCC) 53.1.7.1 TSADCC: Pen detect accuracy is not good Depending on LCD panels, the pen detect is noisy, leading to an unpredictable behavior. Problem Fix/Workaround An additional resistor solves the problem. Its value (between 100kOhm and 250kOhm) is to be tuned for the LCD panel. 53.1.8 USB High Speed Host Port (UHPHS) 53.1.8.1 UHPHS: Packet Loss Issue in the UTMI Transceivers High-Speed USB Host may lose incoming packets when connected to an external USB Hub. A high data transfer error rate has been observed on the High-Speed USB Host interface when connected to an external USB Hub. The USB remains functional but the errors may require a reset of the USB interface to recover. The Full-Speed USB Host operation is not affected by this problem. Problem Fix/Workaround A workaround consists of implementing a timeout on the USB communication using one of the timers in the device and trigger a reset of the USB Host interface via software and restart the communication. The impact of the workaround on the data rate is dependent on the error rate observed in the application but can be such that streaming data at high rates becomes impractical. 53.1.9 USB High Speed Host Port (UHPHS) and Device Port (UDPHS) 53.1.9.1 UHPHS/UDPHS: USB does not start after power-up The USB may not start properly at first use after power-up. If the device boots out of the internal ROM, SAM-BA will not be functional. Problem Fix/Workaround 1. Apply a hardware reset (NRST) after power-up. Or 2. Activate the PLLUTMI twice, following the procedure below: ̶ a- Start The UTMI PLL and wait for the PLL lock bit ̶ b- Disable the UTMI PLL and wait 10 µseconds minimum ̶ c- Restart the UTMIPLL and wait for the PLL Lock bit 1446 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Warning: When booting out of the internal ROM, this workaround is not implemented and therefore SAMBA will not be functional. Below is a possible implementation of the workaround: /* First enable the UTMI PLL */ AT91C_BASE_PMC->CKGR_UCKR |= (AT91C_CKGR_UCKR_PLLCOUNT & (0x3 << 20)) | AT91C_CKGR_UCKR_UPLLEN; tmp =0; while (((AT91C_BASE_PMC->PMC_SR & AT91C_PMC_SR_LOCKU) == 0) && (tmp++ < DELAY)); /* Disable the PLLUTMI and wait 10µs min*/ AT91C_BASE_PMC->CKGR_UCKR &= ~AT91C_CKGR_UCKR_UPLLEN; tmp = 0; while(tmp++ < DELAY2); // DELAY2 must be defined to fit the 10µs min; /* Re- enable the UTMI PLL and wait for the PLL lock status*/ AT91C_BASE_PMC->CKGR_UCKR |= (AT91C_CKGR_UCKR_PLLCOUNT & (0x3 << 20)) | AT91C_CKGR_UCKR_UPLLEN; tmp =0; while (((AT91C_BASE_PMC->PMC_SR & AT91C_PMC_SR_LOCKU) == 0) && (tmp++ < DELAY)); 53.1.9.2 UHPHS/UDPHS: Bad Lock of the USB High speed transceiver DLL The DLL used to oversample the incoming bitstream may not lock in the correct phase, leading to a bad reception of the incoming packets. This issue may occur after the USB device resumes from the Suspend mode. The DLL is used only in the High Speed mode, meaning the Full Speed mode is not impacted by this issue. This issue may occur on the USB device after a reset leading to a SAM-BA connection issue. Problem Fix/Workaround: To prevent a SAM-BA execution issue, the USB device must be connected via a USB Full Speed hub to the PC. At application level, the DLL can be re-initialized in the correct state by toggling the BIASEN bit (high -> low -> high) when resuming from the Suspend mode. The BIASEN bit is located in the CKGR_UCKR register in PMC user interface. The function below can be used to generate the pulse on the bias signal. void generate_pulse_bias(void) { unsigned int * pckgr_uckr = (unsigned int *) 0xFFFFFC1C; * pckgr_uckr &= ~AT91_PMC_BIASEN; * pckgr_uckr |= AT91_PMC_BIASEN; } In the USB device driver, the generate_pulse_bias function must be implemented in the “USB end of reset” and “USB end of resume” interrupts. SAM9M11 [DATASHEET] 1447 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

53.2 SAM9M11 Errata - Rev. B Parts 53.2.1 Boot ROM 53.2.1.1 Boot ROM: NAND Flash boot does not support ECC Correction The boot ROM allows booting from block 0 of a NAND Flash connected on CS3. However, the boot ROM does not feature ECC correction on a NAND Flash. Most of the NAND Flash vendors do not guarantee anymore that block 0 is error free. Therefore we advise to locate the bootstrap program into another device supported by the boot ROM (DataFlash, Serial Flash, SDCARD or EEPROM), and to implement a NAND Flash access with ECC. Problem Fix/Workaround None. 53.2.1.2 Boot ROM: SD Card Boot is not functional The SD card boot functionality does not work due to an issue in the ROM Code. Problem Fix/Workaround The SD card boot functionality can be restored by connecting EBI_D0 and EBI_D6 via 10 kΩ resistors: 1. EBI_D0 should be connected to ground. 2. EBI_D6 should be connected to VDDIOM. 53.2.2 RSTC 53.2.2.1 RSTC: Software reset during DDRAM accesses When a software reset (CPU and peripherals) occurs during DDRAM read access, the CPU will stop the DDRAM clock. The DDRAM maintains the data on the bus until the clock restarts. This will create a bus conflict if another memory sharing the external bus with the DDRAM is accessed prior to completion of the read access to the DDRAM. Such a conflict will occur when the device boots out of an external NAND or NOR Flash following the software reset. Problem Fix/Workaround 1. Boot from serial Flash 2. Before generating the software reset, the user must ensure that all the accesses to DDRAM are completed and then put the DDRAM in self-refresh mode. The routine to generate the software reset must be located in internal SRAM or in the ARM cache memory. 53.2.3 Error Corrected Code Controller (ECC) 53.2.3.1 ECC: Computation with a 1 clock cycle long NRD/NWE pulse If the SMC is programmed with NRD/NWE pulse length equal to 1 clock cycle, ECC cannot compute the parity. Problem Fix/Workaround It is recommended to program SMC with a value superior to 1. 53.2.3.2 Incomplete parity status when error in ECC parity When a single correctable error is detected in ECC value, the error is located in ECC Parity register's field which contains a 1 in the 24 least significant bits except when the error is located in the 12th or the 24th bit. In this case, these bits are always stuck at 0. A Single correctable error is detected but it is impossible to correct it. Problem Fix/Workaround None. 1448 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

53.2.3.3 Unsupported ECC per 512 words 1 bit ECC per 512 words is not functional. Problem Fix/Workaround Perform the ECC computation by software. 53.2.3.4 Unsupported hardware ECC on 16-bit Nand Flash Hardware ECC on 16-bit Nand Flash is not supported. Problem Fix/Workaround Perform the ECC by software. 53.2.4 Pulse Width Modulation Controller (PWM) 53.2.4.1 PWM: Zero Period It is impossible to update a period equal to 0 by using the PWM_CUPD register. Problem Fix/Workaround None 53.2.5 Static Memory Controller (SMC) 53.2.5.1 SMC Delay: Access In this document, the Access is “Read-write” in the Register Mapping Table (SMC_DELAY1 to SMC_DELAY8 rows), and in the SMC DELAY I/O Register. The current access is “Write-only”. Problem Fix/Workaround None 53.2.6 Serial Synchronous Controller (SSC) 53.2.6.1 SSC: Data sent without any frame synchro When SSC is configured with the following conditions:  RF is in input,  TD is synchronized on a receive START (any condition: START field = 2 to 7)  TF toggles at each start of data transfer  Transmit STTDLY = 0  Check TD and TF after a receive START, The data is sent but there is not any toggle of the TF line Problem Fix/Workaround Transmit STTDLY must be different from 0. 53.2.6.2 SSC: Unexpected delay on TD output When SSC is configured with the following conditions:  TCMR.STTDLY more than 0  RCMR.START = Start on falling edge/Start on Rising edge/Start on any edge  RFMR.FSOS = None (input)  TCMR.START = Receive Start Unexpected delay of 2 or 3 system clock cycles is added to TD output. Problem Fix/Workaround None. SAM9M11 [DATASHEET] 1449 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

53.2.7 Touch Screen (TSADCC) 53.2.7.1 TSADCC: Pen detect accuracy is not good Depending on LCD panels, the pen detect is noisy, leading to an unpredictable behavior. Problem Fix/Workaround An additional resistor solves the problem. Its value (between 100kOhm and 250kOhm) is to be tuned for the LCD panel. 53.2.8 Ethernet MAC 10/100 (EMAC) 53.2.8.1 EMAC: setup timing violation with 1.8V I/Os A setup timing violation occurs, when using EMAC in RMII mode only with 1.8V I/Os and 20pF load. The RMII mode is fully functional with 3.3V I/Os. Problem Fix/Workaround None 53.2.9 USB High Speed Host Port (UHPHS) 53.2.9.1 UHPHS: Packet Loss Issue in the UTMI Transceivers High-Speed USB Host may lose incoming packets when connected to an external USB Hub. A high data transfer error rate has been observed on the High-Speed USB Host interface when connected to an external USB Hub. The USB remains functional but the errors may require a reset of the USB interface to recover. The Full-Speed USB Host operation is not affected by this problem. Problem Fix/Workaround A workaround consists of implementing a timeout on the USB communication using one of the timers in the device and trigger a reset of the USB Host interface via software and restart the communication. The impact of the workaround on the data rate is dependent on the error rate observed in the application but can be such that streaming data at high rates becomes impractical. 1450 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

53.2.10USB High Speed Host Port (UHPHS) and Device Port (UDPHS) 53.2.10.1 UHPHS/UDPHS: USB does not start after power-up The USB may not start properly at first use after power-up. If the device boots out of the internal ROM, SAM-BA will not be functional. Problem Fix/Workaround 1. Apply a hardware reset (NRST) after power-up. Or 2. Activate the PLLUTMI twice, following the procedure below: ̶ a- Start The UTMI PLL and wait for the PLL lock bit ̶ b- Disable the UTMI PLL and wait 10 µseconds minimum ̶ c- Restart the UTMIPLL and wait for the PLL Lock bit Warning: When booting out of the internal ROM, this workaround is not implemented and therefore SAMBA will not be functional. Below is a possible implementation of the workaround: /* First enable the UTMI PLL */ AT91C_BASE_PMC->CKGR_UCKR |= (AT91C_CKGR_UCKR_PLLCOUNT & (0x3 << 20)) | AT91C_CKGR_UCKR_UPLLEN; tmp =0; while (((AT91C_BASE_PMC->PMC_SR & AT91C_PMC_SR_LOCKU) == 0) && (tmp++ < DELAY)); /* Disable the PLLUTMI and wait 10µs min*/ AT91C_BASE_PMC->CKGR_UCKR &= ~AT91C_CKGR_UCKR_UPLLEN; tmp = 0; while(tmp++ < DELAY2); // DELAY2 must be defined to fit the 10µs min; /* Re- enable the UTMI PLL and wait for the PLL lock status*/ AT91C_BASE_PMC->CKGR_UCKR |= (AT91C_CKGR_UCKR_PLLCOUNT & (0x3 << 20)) | AT91C_CKGR_UCKR_UPLLEN; tmp =0; while (((AT91C_BASE_PMC->PMC_SR & AT91C_PMC_SR_LOCKU) == 0) && (tmp++ < DELAY)); SAM9M11 [DATASHEET] 1451 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

54. Revision History In the tables that follow, the most recent version appears first. Table 54-1. SAM9M11 Datasheet Rev. 6355I Revision History Date Changes General formatting, editorial and organizational changes throughout Updated Features Section 2. “Signal Description” Section 2-1 “Signal Description List”: - “DDR Memory Interface - DDR2/LPDDR Controller” renamed to “DDR Memory Interface - DDR2/LPDDR Controller - DDRSDRC0” - “DDR2/SDRAM/LPDDR Controller” renamed to “EBI - DDR2/SDRAM/LPDDR Controller - DDRSDRC1” Section 4. “Power Considerations” Added Section 4.2 “Power Sequence Requirements” (transferred and updated content previously in Section 49.12 “Core Power Supply POR Characteristics”) Section 5. “Memories” Section 5.2.2 “TCM Interface”: in first sentence, “can be allocated to two areas” corrected to “can be allocated to three areas Section 5.3.1 “I/O Drive Selection”: “EBI_CSA register” corrected to “CCFG_EBICSA register” Section 7. “Peripherals” Section 7.4 “Peripheral Signals Multiplexing on I/O Lines”: below last paragraph, deleted sentence “To amend EMC, programmable delay has been inserted on PIO lines able to run at high speed” Section 8. “ARM926EJ-S Processor Overview” Table 8-1 “ARM9TDMI Modes and Registers Layout” renamed to “ARM9EJ-S Modes and Registers Layout” Section 8.4.10 “Thumb Instruction Set Overview”: sentence “Table 5 shows the Thumb instruction set, for further details, see the ARM Technical Reference Manual” changed to “For further details, see the ARM Technical Reference Manual.” 17-Dec-15 Section 10. “Boot Strategies” Inserted heading Section 10.1 “Overview” and updated associated text Section 10.5.2.1 “ARM Exception Vectors Check”: updated example at end of section Section 13. “Real-time Clock (RTC)” Section 13.2 “Embedded Characteristics”: deleted bullet “Control of alarm and update Time/Calendar Data In” Table 13-1 “Register Mapping”: RTC_CALR reset value ‘0x01819819’ corrected to ‘0x01210720’; defined offset 0xFC as reserved Section 18. “Bus Matrix (MATRIX)” Removed reset value from register description sections in Section 18.7.6 “Chip Configuration User Interface” (reset values provided in Table 18-7 “Register Mapping (Chip Configuration User Interface)”) Section 19. “External Memories” “EBI_CSA register” corrected to “CCFG_EBICSA register” Table 19-4 “EBI Pins and External Static Devices Connections”: added footnote to pins BE0–BE3 Section “CFCE1 and CFCE2 Signals”: updated content describing DBW field configuration Added Figure 19-9 “NAND Flash Signal Multiplexing on EBI Pins” Section 21. “DDR SDR SDRAM Controller (DDRSDRC)” Added Section 21.2 “Embedded Characteristics” “Product Dependencies” renamed to Section 21.4 “Initialization Sequence” Updated Section 21.4.1 “SDR-SDRAM Initialization” Updated Section 21.4.2 “Low-power DDR1-SDRAM Initialization” 1452 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 54-1. SAM9M11 Datasheet Rev. 6355I Revision History (Continued) Date Changes Section 21. “DDR SDR SDRAM Controller (DDRSDRC)” (cont’d) Updated Section 21.4.3 “DDR2-SDRAM Initialization” Figure 21-12 “Single Read Access, Row Closed, Latency = 3, DDR2-SDRAM Device”: in diagram, inserted additional cycle (“Latency = 2” corrected to “Latency = 3”) Removed “Reset” line from register description sections Section 21.8.3 “DDRSDRC Configuration Register”: bit DQMS changed to EBISHARE and associated description modified Section 21.8.4 “DDRSDRC Timing Parameter 0 Register”: updated TWTR field description Section 21.8.5 “DDRSDRC Timing Parameter 1 Register”: updated TXSRD field description Section 22. “Error Correction Code Controller (ECC)” Table 22-1 “Register Mapping”: removed reset value from ECC_CR (register is write-only) Section 23. “Peripheral DMA Controller (PDC)” Table 23-2 “Register Mapping”: removed reset value from PERIPH_PTCR (register is write-only) Section 24. “Clock Generator” Section 24.5 “Slow Clock Selection”: “Slow Clock Configuration Register” renamed to “Slow Clock Controller Configuration Register” Section 25. “Power Management Controller (PMC)” Table 25-2 “Register Mapping”: - “UTMI Clock Register” corrected to “UTMI Clock Configuration Register” - access for PMC_PLLICPR changed from “Write-only” to “Read/Write” Section 25.12.18 “PLL Charge Pump Current Register”: access changed from “Write-only” to “Read/Write” Section 26. “Serial Peripheral Interface (SPI)” 17-Dec-15 Section 26.8.5 “SPI Status Register”: added four bits ENDTX, ENDRX, RXBUFF, and TXBUFE Section 26.8.6 “SPI Interrupt Enable Register”: added four bits ENDTX, ENDRX, RXBUFF, and TXBUFE Section 26.8.7 “SPI Interrupt Disable Register”: added four bits ENDTX, ENDRX, RXBUFF, and TXBUFE Section 26.8.8 “SPI Interrupt Mask Register”: added four bits ENDTX, ENDRX, RXBUFF, and TXBUFE Section 27. “Advanced Interrupt Controller (AIC)” Removed reset value from register description sections (reset values provided in Table 27-3 “Register Mapping”) Section 30. “Universal Synchronous Asynchronous Receiver Transmitter (USART)” Table 30-8 “Possible Values for the Fi/Di Ratio”: in top row, “774” corrected to “744” Table 30-13 “IrDA Baud Rate Error”: in header row, added “bit/s” to Baud Rate and added “µs” to Pulse Time Section 30.7.8.7 “Slave Node Synchronization”: in list of parameters, “Over=0 => 8X” corrected to “OVER=1 => 8X” Table 30-17 “Register Mapping”: added reset value 0x0 to US_MR, US_CSR, US_NER Removed reset value from Section 30.8.12 “USART FI DI RATIO Register” (reset values provided in Table 30-17 “Register Mapping”) Section 31. “Two-wire Interface (TWI)” Table 31-6 “Register Mapping”: removed reset value from TWI_THR (register is write-only) Removed reset value from register description sections (reset values provided in Table 31-6 “Register Mapping”) Section 32. “Synchronous Serial Controller (SSC)” Section 32.7.1.1 “Clock Divider”: at end of section, deleted irrelevant and untitled Table 35-4 Section 34. “DMA Controller (DMAC)” Inserted heading Section 34.3 “DMA Controller Peripheral Connections” and updated text Removed reset value from register description sections (reset values provided in Table 34-3 “Register Mapping”) SAM9M11 [DATASHEET] 1453 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 54-1. SAM9M11 Datasheet Rev. 6355I Revision History (Continued) Date Changes Section 36. “High Speed Multimedia Card Interface (HSMCI)” Table 36-8 “Register Mapping”: defined offset range 0x100–0x1FC as reserved; offset range for FIFO Memory Aperture registers updated to 0x200–0x5FC Section 36. “High Speed Multimedia Card Interface (HSMCI)” (cont’d) Section 36.14.12 “HSMCI Status Register”: in bitmap, “MCI_SDIOIRQA” corrected to “SDIOIRQA” Section 36.14.13 “HSMCI Interrupt Enable Register”: in bitmap, “MCI_SDIOIRQA” corrected to “SDIOIRQA” Section 36.14.14 “HSMCI Interrupt Disable Register”: in bitmap, “MCI_SDIOIRQA” corrected to “SDIOIRQA” Section 36.14.15 “HSMCI Interrupt Mask Register”: in bitmap, “MCI_SDIOIRQA” corrected to “SDIOIRQA” Section 36.14.20 “HSMCI FIFOx Memory Aperture”: name “HSMCI_FIFO” updated to “HSMCI_FIFOx[x=0..255]” Section 38. “USB High Speed Host Port (UHPHS)” Updated Section 38.4.2 “Power Management” Section 39. “USB High Speed Device Port (UDPHS)” Deleted three notes below Figure 39-2 “Block Diagram” Table 39-5 “Register Mapping”: removed UDPHS Name1 Register / UDPHS_IPNAME1, UDPHS Name2 Register / UDPHS_IPNAME2, and UDPHS Features Register / UDPHS_IPFEATURES; defined offset range 0xE4–0xF8 as reserved Deleted three sections “UDPHS Name1 Register”, “UDPHS Name2 Register”, and “UDPHS Features Register” Section 40. “Image Sensor Interface (ISI)” Table 40-9 “Register Mapping”: removed reset values from write-only registers; defined offset ranges 0x5C–0xE0 and 0xEC–0xF8 as reserved Removed reset value from register description sections (reset values provided in Table 40-9 “Register Mapping”) Section 41. “Touchscreen ADC Controller (TSADCC)” 17-Dec-15 Updated Section 41.2 “Embedded Characteristics” Figure 41-1 “TSADCC Block Diagram”: “ADTRG” corrected to “TSADTRG”; “ADVREF” corrected to “TSADVREF” Table 41-4 “Register Mapping”: defined offset range 0x64–0xE0 as “Reserved” Section 41.11.18 “TSADCC Write Protection Mode Register”: updated WPEN bit description; added KEY field description Section 46. “True Random Number Generator (TRNG)” Removed reset value from Section 46.2.4 “TRNG Interrupt Mask Register”, Section 46.2.5 “TRNG Interrupt Status Register”, and Section 46.2.6 “TRNG Output Data Register” (reset values provided in Table 46-1 “Register Mapping”) Section 47. “LCD Controller (LCDC)” Table 47-15 “Register Mapping”: removed reset value from write-only registers Removed reset value from register description sections (reset values provided in Table 47-15 “Register Mapping”) Section 48. “Video Decoder (VDEC)” Updated Section 48.1 “Description” Section 48.4.1 “Power Management”: updated text in first paragraph Table 48-9 “Video Decoder Register Mapping (All Decoders)”: - VDEC_IDR reset value ‘0x81701000’ corrected to ‘0x81700880’ - removed reset value from reserved offset 0x00C8 Table 48-10 “Video Decoder Register Mapping (H264)”: removed reset value from reserved offset 0x00C8 Table 48-11 “Video Decoder Register Mapping (MPEG4H263)”: removed reset value from reserved offset 0x00C8 Table 48-12 “Video Decoder Register Mapping (JPEG)”: removed reset value from reserved offset 0x00C8 Table 48-13 “Video Decoder Register Mapping (VC1)”: removed reset value from reserved offset 0x00C8 1454 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table 54-1. SAM9M11 Datasheet Rev. 6355I Revision History (Continued) Date Changes Section 48. “Video Decoder (VDEC)” (cont’d) Table 48-14 “Video Decoder Register Mapping (MPEG-2/MPEG-1)”: removed reset value from reserved offset 0x00C8 Table 48-15 “Video Post-processor Register Mapping”: added row for reserved offset 0x0190 Section 48.9.9 “Decoder Control Register 5 (VC-1 Control)”: name VDEC_CTRL4 corrected to VDEC_CTRL5 Section 49. “SAM9M11 Electrical Characteristics” Table 49-1 “Absolute Maximum Ratings*”: removed “Operating Temperature” line Table 49-4 “Power Consumption by Peripheral in Active Mode”: added peripherals AES and SHA Table 49-22 “External Voltage Reference Input”: “ADVREF” corrected to “TSADVREF” Section 49.12 “Core Power Supply POR Characteristics”: transferred sections “Power Sequence Requirements”, “Power- Up Sequence” and “Power-Down Sequence” to Section 4.2 “Power Sequence Requirements” Table 49-31 “SMC Write Signals - NWE Controlled (WRITE_MODE = 1)”: in row SMC , “ncs rd setup” corrected to 18 17-Dec-15 “ncswr setup” Section 49.15.1.1 “Maximum SPI Frequency”: under Master Write Mode, “SPI frequency is defined by the pin FreqMax value” changed to “SPI frequency is the one from the pad” Section 49.15.1.3 “Timing Extraction”: added content relative to MISO and MOSI sampling; inserted Figure 49-6 “MISO Capture in Master Mode” Section 49.15.5.2 “Timing Constraints”: updated first sentence Section 49.15.6 “USART in SPI Mode”: instances of “UART” corrected to “USART” Table 49-48 “USART SPI Timings with 1.8V Peripheral Supply”: added footnote relating to SPCK access times Section 50. “Mechanical Characteristics” Replaced Table 47-5 “Soldering Information” with Table 50-1 “Package Information” Section 52. “SAM9M11 Ordering Information” Table 52-1 “SAM9M11 Ordering Information”: “Package Type” column replaced by “Carrier Type” column Doc. Rev. Date Changes Minor editorial and formatting changes throughout Section “Description” Added paragraph relating to low-power modes Section “Features” Added several peripheral acronyms Added bullet “Three Low-power Modes: Idle, Ultra Low-power, and Backup” Section 1. “Block Diagram” 6437G 09-Jun-15 Figure 1-1 “SAM9M11 Block Diagram”: added label “Backup Section” in System Controller block Section 5. “Memories” Figure 5-1 “SAM9M11 Memory Mapping”: updated acronyms under “Peripheral Mapping” and “System Controller Mapping” Section 10. “Boot Strategies” Section 10.4.3.3 “SPI Flash Boot”: changed instance of “Atmel DataFlash devices” to “DataFlash devices” Section 10.5.3.2 “USB class”: changed “from Windows 98SE® to Windows XP®” to “beginning with Windows 98SE®” SAM9M11 [DATASHEET] 1455 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Doc. Rev. Date Changes (Continued) Section 49. “SAM9M11 Electrical Characteristics” Updated parameter symbols throughout Added Section 49.12.3 “Power-Down Sequence” Table 49-5 “Processor Clock Waveform Parameters”: added footnote “For DDR2 usage, there are no limitations to LPDDR, SDRAM and mobile SDRAM.” Table 49-27 “Capacitance Load” : specified “VDDIOM” as supply Table 49-31 “SMC Write Signals - NWE Controlled (WRITE_MODE = 1)”: specified “VDDIOM” as supply Table 49-32 “SMC Write NCS Controlled (WRITE_MODE = 0)”: specified “VDDIOM” as supply In Section 49.15.1.1 “Maximum SPI Frequency”, updated description under Master Write Mode and 6437G 09-Jun-15 Master Read Mode Updated Table 49-37 “SSC Timings with 3.3V Peripheral Supply” and Table 49-38 “SSC Timings with 1.8V Peripheral Supply” Table 49-45 “RMII Mode”: updated max value for EMAC ; deleted stray footnote “See Note (2) of Table 49- 21 42” Section 50. “Mechanical Characteristics” Figure 50-1 “324-ball TFBGA Package Drawing”: corrected ‘E’ min dimension in inches to 0.5886 Inserted Section 51. “Marking” Section 53. “SAM9M11 Errata” Removed subsection 52.1 “Marking” Doc. Rev 6437F Changes Updated document format Added “Write protected registers” in Features Added one sentence for NRST in Table 2-1, “Signal Description List” Updated Section 44. “Triple Data Encryption Standard (TDES)” Modified I values in Table 49-14, “PLLA Characteristics” PLL Updated Section 49.12.2 “Power-Up Sequence” (added one sentence at the end of the section) Added Section 53.2.1.2 “Boot ROM: SD Card Boot is not functional” in Section 53.2 “SAM9M11 Errata - Rev. B Parts” Change Doc. Rev Request 6437E Comments Ref.(1) In “Description” on page1, added mention of DBGU. rfo 8809 Corrected acesses to DDR Port 2 in Table 18-3 “SAM9M11 Masters to Slaves Access with VDEC_SEL = 0”and Table 18-4 “SAM9M11 Masters to Slaves Access with VDEC_SEL = 1 (default)”. Corrected reset value for EBI Chip Select Assignment Registerin Table 18-7 “Register Mapping (Chip 8007 Configuration User Interface)”and in Section 18.7.6.3 “EBI Chip Select Assignment Register” 1456 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Change Doc. Rev Request 6437E Comments (Continued) Ref.(1) 8551 Update with Rev. B ordering code in Table 52-1 “SAM9M11 Ordering Information” Insert Section 53.2 “SAM9M11 Errata - Rev. B Parts” on page 1448. 8372 In Section 53.1 “SAM9M11 Errata - Rev. A Parts” replace errata Section 52.3.11.1 “PMC: Bad Lock of the USB High speed transceiver DLL” with updated errata Section 53.1.9.2 “UHPHS/UDPHS: Bad Lock of the USB High speed transceiver DLL”. Change Doc. Rev Request 6437D Comments Ref.(1) Boot Strategies 8268 Table 10-1 added. SPI rfo Blank pages deleted. Errata Section 53.1.1.2 “Boot ROM: Boot issue on AT45-series SPI Dataflash” added. 8080 Section 53.1.2 “Reset Controller (RSTC)” added. 8111 Revision History Doc. rev number was 6355C, replaced by 6437C. rfo Reference to SAM9M10 replaced by SAM9M11. Change Doc. Rev Request 6437C Comments Ref.(1) Introduction Product Line/Product naming convention changed - AT91SAM ARM-based MPU / SAM9M11 rfo Section 5. “Memories”, replaced ground pin names by GNDIOM, GNDCORE, GNDANA, GNDIOP, 7332 GNDBU, GNDOSC, GNDUTMI. Reorganized text describing GND association to power supply pins rfo Clock Generator 7332 Figure 24-2 and Figure 24-5, GND changed to GNDOSC. DDRSDRC 7462 “DDRSDRC Timing 1 Parameter Register",TXSNR field, “Number of cycles is between 0 and 255”. PMC 7392 Section 25.5 “Processor Clock Controller”, 2nd and 3rd paragraphs edited. RTC 7569 Section 13.6 “Real-time Clock (RTC) User Interface”, typo in section title fixed. SPI 7509 WDRBT variable and conditional text shown, now appearing in Section 26.8.2 “SPI Mode Register” SAM9M11 [DATASHEET] 1457 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Change Doc. Rev Request 6437C Comments (Continued) Ref.(1) TRNG 7531 KEY bitfield added to “TRNG Control Register”. TWI 7266 Section 30.2 “Embedded Characteristics”, PDC feature removed from the list. UDPHS 7332 Figure 39-3 “Board Schematic”, GND changed to GNDUTMI. UHPHS Figure 38-4 “Board Schematic to Interface UHP High-speed Device Controller”, GND changed to 7332 GNDUTMI. Electrical Characteristics Table 49-23, “Analog Inputs”, ’ Input Impedance’ changed to ‘Input Source Impedance’. 7519 In the footnote below Table 49-7 “Main Oscillator Characteristics” , gnd changed to gndosc. 7332 In the figure below, GNDPLL changed to GNDOSC. ‘pF’ value has to be written this way: ‘Pf’ and ‘pf’ removed. rfo Errata 7384 Section 53.1.3.1 “ECC: Computation with a 1 clock cycle long NRD/NWE pulse”, HECC changed to ECC. Section 53.1.8.1 “UHPHS: Packet Loss Issue in the UTMI Transceivers” added. 7595 Section 53.1.9.1 “UHPHS/UDPHS: USB does not start after power-up”, a clarifying “Or” added to 7352 choices in “Workaround”. Change Doc. Rev Request 6437B Comments Ref.(1) DDRSDRC In Section 21.4.4.1 “Self Refresh Mode”, UDP_EN replaced by UPD_MR. In Section 21.7.7 “DDRSDRC Low-power Register”, UPD_MR bitfield added to the table at [21:20]. 7089 In Section 21.7.6 “DDRSDRC Timing 2 Parameter Register”: - TRTP bitfield reset value (0 --> 2) changed. 7146 - 0 and 15’ cycles changed into ‘0 and 7’ in ”TRTP: Read to Precharge”. - TXARD (-->2) and TXARDS (-->6) reset values changed. HSMCI: Updated bifields in User Interface. RFO Electrical Characteristics Section 49.14 “DDRSDRC Timings” edited. 7134 Section 49.15.1.1 “Maximum SPI Frequency” added. 7173 Section 49.14 “DDRSDRC Timings” edited. 7193 Ultra low power Mode value changed in Table 49-3 “Power Consumption for Different Modes” . 7195 1458 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Change Doc. Rev Request 6437B Comments (Continued) Ref.(1) ERRATA - Boot ROM errata added. 7148 - 3 Error Corrected Code Controller (ECC)errata added: ECC: Incomplete parity status when error in 7192 ECC parity, ECC: Unsupported ECC per 512 wordsand ECC: Unsupported hardware ECC on 16-bit Nand Flash. 7165 - Touch Screen (TSADCC)errata added. 7194 - USB High Speed Host Port (UHPHS)errata added. 6437A First issue Note: 1. “rfo” indicates changes requested during document review and approval loop. SAM9M11 [DATASHEET] 1459 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

Table of Contents Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1. Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. Package and Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.1 Mechanical Overview of the 324-ball TFBGA Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.2 324-ball TFBGA Package Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4. Power Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4.1 Power Supplies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4.2 Power Sequence Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5. Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5.1 Memory Mapping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5.2 Embedded Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5.3 I/O Drive Selection and Delay Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6. System Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 6.1 System Controller Mapping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 6.2 System Controller Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 6.3 Chip Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 6.4 Backup Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 7. Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 7.1 Peripheral Mapping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 7.2 Peripheral Identifiers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 7.3 Peripheral Interrupts and Clock Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 7.4 Peripheral Signals Multiplexing on I/O Lines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 8. ARM926EJ-S Processor Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 8.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 8.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 8.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 8.4 ARM9EJ-S Processor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 8.5 CP15 Coprocessor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 8.6 Memory Management Unit (MMU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 8.7 Caches and Write Buffer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 8.8 Tightly-Coupled Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 8.9 Bus Interface Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 9. SAM9M11 Debug and Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 9.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 9.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 9.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 9.4 Application Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 9.5 Debug and Test Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 9.6 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 1460 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

10. Boot Strategies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 10.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 10.2 Boot Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 10.3 Flow Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 10.4 Device Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 10.5 NVM Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 10.6 SAM-BA Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 11. Reset Controller (RSTC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 11.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 11.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 11.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 11.4 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 11.5 Reset Controller (RSTC) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 12. Real-time Timer (RTT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 12.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 12.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 12.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 12.4 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 12.5 Real-time Timer (RTT) User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 13. Real-time Clock (RTC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 13.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 13.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 13.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 13.4 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 13.5 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 13.6 Real-time Clock (RTC) User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 14. Periodic Interval Timer (PIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 14.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 14.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 14.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 14.4 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 14.5 Periodic Interval Timer (PIT) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 15. Watchdog Timer (WDT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 15.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 15.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 15.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 15.4 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 15.5 Watchdog Timer (WDT) User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 16. Shutdown Controller (SHDWC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 16.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 16.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 16.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 16.4 I/O Lines Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 16.5 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 16.6 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 16.7 Shutdown Controller (SHDWC) User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 SAM9M11 [DATASHEET] 1461 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

17. General Purpose Backup Registers (GPBR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 17.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 17.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 17.3 General Purpose Backup Registers (GPBR) User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 18. Bus Matrix (MATRIX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 18.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 18.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 18.3 Memory Mapping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 18.4 Special Bus Granting Mechanism. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 18.5 Arbitration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 18.6 Write Protect Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 18.7 Bus Matrix (MATRIX) User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 19. External Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 19.1 DDRSDRC0 Multi-port DDRSDR Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 19.2 External Bus Interface (EBI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 20. Static Memory Controller (SMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 20.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 20.2 I/O Lines Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 20.3 Multiplexed Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 20.4 Application Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188 20.5 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188 20.6 External Memory Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189 20.7 Connection to External Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189 20.8 Standard Read and Write Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 20.9 Automatic Wait States. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 20.10 Data Float Wait States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 20.11 External Wait. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 20.12 Slow Clock Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 20.13 Asynchronous Page Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 20.14 Programmable IO Delays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219 20.15 Static Memory Controller (SMC) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 21. DDR SDR SDRAM Controller (DDRSDRC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 21.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 21.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 21.3 DDRSDRC Module Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 21.4 Initialization Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 21.5 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 21.6 Software Interface/SDRAM Organization, Address Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252 21.7 Programmable IO Delays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254 21.8 DDR SDR SDRAM Controller (DDRSDRC) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 22. Error Correction Code Controller (ECC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273 22.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273 22.2 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273 22.3 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 22.4 Error Correction Code Controller (ECC) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 22.5 Registers for 1 ECC for a page of 512/1024/2048/4096 bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289 22.6 Registers for 1 ECC per 512 bytes for a page of 512/2048/4096 bytes, 8-bit word . . . . . . . . . . . . 291 1462 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

22.7 Registers for 1 ECC per 256 bytes for a page of 512/2048/4096 bytes, 8-bit word . . . . . . . . . . . . 299 23. Peripheral DMA Controller (PDC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315 23.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315 23.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315 23.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317 23.4 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318 23.5 Peripheral DMA Controller (PDC) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 24. Clock Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331 24.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331 24.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331 24.3 Slow Clock Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332 24.4 Slow Clock RC Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332 24.5 Slow Clock Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332 24.6 Main Oscillator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 24.7 Divider and PLLA Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336 24.8 UTMI Bias and Phase Lock Loop Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337 25. Power Management Controller (PMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338 25.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338 25.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338 25.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339 25.4 Master Clock Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340 25.5 Processor Clock Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340 25.6 USB Device and Host clocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341 25.7 LPDDR/DDR2 Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341 25.8 Peripheral Clock Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341 25.9 Programmable Clock Output Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342 25.10 Programming Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342 25.11 Clock Switching Details. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345 25.12 Power Management Controller (PMC) User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348 26. Serial Peripheral Interface (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368 26.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368 26.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368 26.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369 26.4 Application Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 26.5 Signal Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 26.6 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371 26.7 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372 26.8 Serial Peripheral Interface (SPI) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385 27. Advanced Interrupt Controller (AIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398 27.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398 27.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398 27.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399 27.4 Application Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399 27.5 AIC Detailed Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399 27.6 I/O Line Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 27.7 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 27.8 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401 SAM9M11 [DATASHEET] 1463 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

27.9 Advanced Interrupt Controller (AIC) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410 28. Debug Unit (DBGU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429 28.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429 28.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429 28.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430 28.4 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431 28.5 UART Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431 28.6 Debug Unit (DBGU) User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438 29. Parallel Input/Output Controller (PIO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454 29.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454 29.2 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455 29.3 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456 29.4 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457 29.5 I/O Lines Programming Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463 29.6 Parallel Input/Output Controller (PIO) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464 30. Universal Synchronous Asynchronous Receiver Transmitter (USART) . . . . . . . . . 498 30.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 498 30.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 498 30.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499 30.4 Application Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 30.5 I/O Lines Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 30.6 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 501 30.7 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503 30.8 Universal Synchronous Asynchronous Receiver Transmitter (USART) User Interface . . . . . . . . . 547 31. Two-wire Interface (TWI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 576 31.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 576 31.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 576 31.3 List of Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 577 31.4 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 577 31.5 Application Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578 31.6 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578 31.7 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 579 31.8 Two-wire Interface (TWI) User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 601 32. Synchronous Serial Controller (SSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 616 32.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 616 32.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 616 32.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 617 32.4 Application Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 618 32.5 Pin Name List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 619 32.6 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 619 32.7 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 621 32.8 SSC Application Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 632 32.9 Synchronous Serial Controller (SSC) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 634 33. Timer Counter (TC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 659 33.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 659 33.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 659 1464 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

33.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 660 33.4 Pin Name List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 661 33.5 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 661 33.6 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 662 33.7 Timer Counter (TC) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 674 34. DMA Controller (DMAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693 34.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693 34.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 694 34.3 DMA Controller Peripheral Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 695 34.4 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 696 34.5 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 697 34.6 DMAC Software Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723 34.7 DMA Controller (DMAC) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 724 35. Pulse Width Modulation Controller (PWM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 748 35.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 748 35.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 748 35.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 749 35.4 I/O Lines Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 749 35.5 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 750 35.6 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 751 35.7 Pulse Width Modulation Controller (PWM) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 758 36. High Speed Multimedia Card Interface (HSMCI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 773 36.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 773 36.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 773 36.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 774 36.4 Application Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 775 36.5 Pin Name List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 775 36.6 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 776 36.7 Bus Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 777 36.8 High Speed MultiMediaCard Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 779 36.9 SD/SDIO Card Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 797 36.10 CE-ATA Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 798 36.11 HSMCI Boot Operation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 799 36.12 HSMCI Transfer Done Timings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 801 36.13 Write Protection Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 802 36.14 High Speed MultiMediaCard Interface (HSMCI) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 803 37. Ethernet MAC 10/100 (EMAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 832 37.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 832 37.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 832 37.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 833 37.4 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 834 37.5 Programming Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 844 37.6 Ethernet MAC 10/100 (EMAC) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 847 38. USB High Speed Host Port (UHPHS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 902 38.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 902 38.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 902 38.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 903 SAM9M11 [DATASHEET] 1465 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

38.4 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 904 38.5 Typical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 906 39. USB High Speed Device Port (UDPHS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 907 39.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 907 39.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 907 39.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 909 39.4 Typical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 910 39.5 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 911 39.6 USB High Speed Device Port (UDPHS) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 933 40. Image Sensor Interface (ISI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 969 40.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 969 40.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 969 40.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 970 40.4 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 971 40.5 Image Sensor Interface (ISI) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 979 41. Touchscreen ADC Controller (TSADCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1009 41.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1009 41.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1010 41.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1011 41.4 Signal Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1011 41.5 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1012 41.6 Analog-to-digital Converter Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1012 41.7 Touchscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1014 41.8 Conversion Results. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1018 41.9 Conversion Triggers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1019 41.10 Operating Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1020 41.11 Touchscreen ADC Controller (TSADCC) User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1027 42. AC97 Controller (AC97C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1049 42.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1049 42.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1049 42.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1050 42.4 Pin Name List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1051 42.5 Application Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1051 42.6 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1052 42.7 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1053 42.8 AC97 Controller (AC97C) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1062 43. Advanced Encryption Standard (AES) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1084 43.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1084 43.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1084 43.3 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1085 43.4 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1085 43.5 Advanced Encryption Standard (AES) User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1091 44. Triple Data Encryption Standard (TDES) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1104 44.1 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1104 44.2 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1105 44.3 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1105 1466 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

44.4 Triple Data Encryption Standard (TDES) User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1111 45. Secure Hash Algorithm (SHA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1127 45.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1127 45.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1127 45.3 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1127 45.4 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1128 45.5 Secure Hash Algorithm (SHA) User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1130 46. True Random Number Generator (TRNG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1139 46.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1139 46.2 True Random Number Generator (TRNG) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1140 47. LCD Controller (LCDC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1147 47.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1147 47.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1147 47.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1148 47.4 I/O Lines Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1149 47.5 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1149 47.6 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1151 47.7 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1170 47.8 Configuration Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1170 47.9 Double-buffer Technique. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1171 47.10 2D Memory Addressing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1172 47.11 Register Configuration Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1173 47.12 LCD Controller (LCDC) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1174 48. Video Decoder (VDEC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1213 48.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1213 48.2 Embedded Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1213 48.3 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1214 48.4 Product Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1221 48.5 Video Decoder User Interface (VDEC) User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1222 48.6 Video Decoder Register Mapping (H.264) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1224 48.7 Video Decoder Register Mapping (MPEG-4/H.263) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1265 48.8 Video Decoder Register Mapping (JPEG). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1293 48.9 Video Decoder Register Mapping (VC-1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1322 48.10 Video Decoder Register Mapping (MPEG-2/MPEG-1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1354 48.11 Video Post-processor Register Mapping (All Decoders). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1375 49. SAM9M11 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1410 49.1 Absolute Maximum Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1410 49.2 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1410 49.3 Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1412 49.4 Clock Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1413 49.5 Main Oscillator Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1414 49.6 32 kHz Oscillator Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1415 49.7 32 kHz RC Oscillator Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1416 49.8 PLL Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1416 49.9 I/Os . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1417 49.10 USB HS Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1418 49.11 Touchscreen ADC Controller (TSADCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1419 SAM9M11 [DATASHEET] 1467 Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

49.12 Core Power Supply POR Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1420 49.13 SMC Timings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1420 49.14 DDRSDRC Timings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1424 49.15 Peripheral Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1424 50. Mechanical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1440 50.1 Package Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1440 50.2 Soldering Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1441 51. Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1442 52. SAM9M11 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1443 53. SAM9M11 Errata . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1444 53.1 SAM9M11 Errata - Rev. A Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1444 53.2 SAM9M11 Errata - Rev. B Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1448 54. Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1452 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1460 1468 SAM9M11 [DATASHEET] Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15

ARM Connected Logo X X X X X X Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com © 2015 Atmel Corporation. / Rev.: Atmel-6437H-ATARM-SAM9M11-Datasheet_17-Dec-15. Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation in U.S. and other countries. ARM®, ARM Connected® logo, and others are the registered trademarks or trademarks of ARM Ltd. Windows® and others are registered trademarks or trademarks of Microsoft Corporation in the US and/or other countries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: M icrochip: AT91SAM9M11B-CU