Active Errata List • During UART Reception, Clearing REN May Generate Unexpected IT • Timer 2 – Baud Rate Generator – Long Start Time • C51 Core – Bad Exit of Power-down in X2 Mode • PCA – Incorrect Behavior with CPU X2 Mode Bit of HSB • Timer0/1 – Extra Interrupt • Boot process - Upper 2Kbytes execution with BLJB=0 • Flash/EEPROM - First Read after Load Disturbed Errata History 80C51 MCUs Lot Number Errata List All 1, 2, 3, 4, 5, 6, 7 AT89C51RD2 AT89C51ED2 Errata Descriptions 1. During UART Reception, Clearing REN May Generate Unexpected IT During UART reception, if the REN bit is cleared between start bit detection and Errata Sheet the end of reception, the UART will not discard the data (RI is set). Workaround Test REN at the beginning of Interrupt routine directly after CLR RI, and run the Interrupt routine code only if REN is set. 2. Timer 2 – Baud Rate Generator – Long Start Time When Timer 2 is used as a baud rate generator, TH2 is not loaded with RCAP2H at the beginning, then UART is not operational before 10,000 machine cycles. Workaround Add the initialization of TH2 and TL2 in the initialization of Timer 2. 3. C51 Core – Bad Exit of Power-down in X2 Mode When exiting power-down mode by interrupt while CPU is in X2 mode, it leads to bad execution of the first instruction run when CPU restarts. Workaround Set the CPU in X1 mode diretly before entering power-down mode. 4. PCA – Incorrect behavior with CPU X2 mode bit of HSB When starting the microcontroller in X2 mode upon reset with the X2 fuse bit of the HSB, the PCA may not work properly when configured with Timer 0 in X1 mode as clock input. Workaround Set the CPU in X2 mode by software by writing CKCON register at the begin of the application. 5. Timer0/1 – Extra Interrupt When Timer0 is in X1 mode and Timer1 in X2 mode and vice versa, extra inter- rupt may randomly occur for Timer0 or Timer1. Workaround 4257E–8051–08/07

Use the same mode for the two timers.. 6. Boot Process - Upper 2Kbytes Execution with BLJB = 0 In case of Boot process with BLJB = 0 and BSB = 00, the User Application is executed but the program space located in the upper 2KBytes of the 64KBytes on chip Flash memory cannot be executed. This is due to ENBOOT bit which is set in this Bootloader flow. Workaround Clear ENBOOT bit at the beginning of user application software. 7. Flash/EEPROM - First Read after Load Disturbed In the ‘In-Application Programming’ mode from the Flash, if the User software application loads the Column Latch Area prior to calling the programming sequence in the UART Bootloader. The ‘Read after load’ issue leads to a wrong Opcode Fetch during the column latch load sequence. Workaround Update of the Flash API Library. A NOP instruction has to be inserted after the load instruction. MOVX @DPTR,A ;Load Column latches NOP ; ADDED INSTRUCTION AT89C51RD2/ED2 2 4257E–8051–08/07

Active UART BootloaderErrata List • API program Data Byte - Incorrect Return Value • API program Data Page - Incorrect Return Value UART Bootloader Errata History Version Number Errata List 0.0 (1.0.0 displayed by FLIP) 1,2 UART Bootloader Errata Description 1. API Program Data Byte - Incorrect Return Value The PROGRAM DATA BYTE API returns the ‘0xXX’ instead of 0x00 in ACC, but the programmnig operation is sucess- fully completed. 2. API Program Data Page- Incorrect Return Value The PROGRAM DATA PAGE API returns the ‘0xXX’ instead of 0x00 in ACC, but the programmnig operation is sucess- fully completed. AT89C51RD2/ED2 3 4257E–8051–08/07

Atmel Corporation Atmel Operations 2325 Orchard Parkway Memory RF/Automotive San Jose, CA 95131, USA 2325 Orchard Parkway Theresienstrasse 2 Tel: 1(408) 441-0311 San Jose, CA 95131, USA Postfach 3535 Fax: 1(408) 487-2600 Tel: 1(408) 441-0311 74025 Heilbronn, Germany Fax: 1(408) 436-4314 Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 Regional Headquarters Microcontrollers 2325 Orchard Parkway 1150 East Cheyenne Mtn. Blvd. Europe San Jose, CA 95131, USA Colorado Springs, CO 80906, USA Atmel Sarl Tel: 1(408) 441-0311 Tel: 1(719) 576-3300 Route des Arsenaux 41 Fax: 1(408) 436-4314 Fax: 1(719) 540-1759 Case Postale 80 CH-1705 Fribourg La Chantrerie Biometrics Switzerland BP 70602 Avenue de Rochepleine Tel: (41) 26-426-5555 44306 Nantes Cedex 3, France BP 123 Fax: (41) 26-426-5500 Tel: (33) 2-40-18-18-18 38521 Saint-Egreve Cedex, France Fax: (33) 2-40-18-19-60 Tel: (33) 4-76-58-47-50 Asia Fax: (33) 4-76-58-47-60 Room 1219 ASIC/ASSP/Smart Cards Chinachem Golden Plaza Zone Industrielle 77 Mody Road Tsimshatsui 13106 Rousset Cedex, France East Kowloon Tel: (33) 4-42-53-60-00 Hong Kong Fax: (33) 4-42-53-60-01 Tel: (852) 2721-9778 Fax: (852) 2722-1369 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Japan Tel: 1(719) 576-3300 9F, Tonetsu Shinkawa Bldg. Fax: 1(719) 540-1759 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Scottish Enterprise Technology Park Japan Maxwell Building Tel: (81) 3-3523-3551 East Kilbride G75 0QR, Scotland Fax: (81) 3-3523-7581 Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise,to any intellectualproperty right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representationsor warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustainlife. ©2007 Atmel Corporation. All rights reserved. Atmel®, logo and combinations thereof, and Everywhere You Are® are the trademarks or regis- tered trademarks, of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 4257E–8051–08/07

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: M icrochip: AT89C51ED2-RDRUM AT89C51ED2-RLRUM AT89C51ED2-SLRUM AT89C51ED2-SMRUM AT89C51RD2- RLRUM AT89C51RD2-RLTUM AT89C51ED2-SLSUM AT89C51ED2-RLTUM AT89C51ED2-SMSUM AT89C51ED2- RDTUM