85-0322 Design Cover Sheet 1/7/2009 ACS7xx Demo Board Page 1 of 1 Originator: Shawn Upton Design Rev -> OI A B C Doc Size Format Name, Description Sub-Document Revision 000 - - Final Assembly 1 2 OBS 000-REV A pdf Revision Control 3 4 000-TOP A pdf Top Level Instructions 3 3 000-OPT A pdf Build Options 3 3 000-ASY A pdf Assembly Instructions 3 4 000-TST A pdf Test and Verification 3 3 Bare Board 000-BOM - - Bill of Materials 1 2 OBS 000-SCH A pdf Schematic 1 2 2 2 000-BD1 B pdf Board Outline 1 3 3 3 000-SS1 A pdf Top Silkscreen 1 3 3 3 000-SM1 A pdf Top Soldermask 1 3 3 3 000-SM2 A pdf Bottom Soldermask 1 3 3 3 000-CU1 A pdf Top Layer 1 3 3 3 000-CU2 A pdf Bottom Layer 1 3 3 3 000-GD1 A pdf Drill Drawing 1 3 3 3 000-GG1 A pdf Drill Guide 1 3 3 3 000-ZIP - zip Gerber Files 1 3 3 3 000-NTS - - Construction Notes 1 2 OBS Assembled board, no sensor 001-BOM A pdf Bill of Materials 3 3 ACS712ELC-05B-T 010-BOM A pdf Bill of Materials 3 3 ACS712ELC-20A-T 011-BOM A pdf Bill of Materials 3 3 ACS712ELC-30A-T 012-BOM A pdf Bill of Materials 3 3 ACS713ELC-20A-T 013-BOM A pdf Bill of Materials 3 3 ACS713ELC-30A-T 014-BOM A pdf Bill of Materials 3 3

ACS7xx Demo Board Revision Control Rev 4 85-0322-000-REV Page 1 of 1 1/7/2009 Originator: Shawn Upton Rev OI to Rev A Changes: 1. Not documented. How to convert Rev OI to Rev A: 1. Not possible. Rev A to Rev B Changes: 1. This update was to change TED paperwork to latest standards. 2. No PCB or schematic changes. 3. REV, ASY, OPT, TOP pages added. 4. The BOM for the board, minus sensor, moved to -001 (from -000). This was done to fit into the "no -000 assembly" method of multiple build option demo boards. How to convert Rev A to Rev B: 1. No changes necessary. Rev B to Rev C Changes: 1. Assembly Instructions fixed: Step 5 had RJ installed as 0.125" and 0.25" in error. Changed to be 0.125" installation height. 2. No other changes. How to convert Rev B to Rev C: 1. No changes necessary.

ACS7xx Demo Board Top Level Instructions Rev 3 85-0322-000-TOP PAGE 1 OF 1 5/28/2008 Originator: Shawn Upton 1. RoHS Compliance Required? Yes. All components and assembly practices must be RoHS Compliant. Certificates of RoHS compliance must be sent to Allegro for record keeping. 2. Other TED Packs and/or outside Specifictions required for build: none required. 3. Are there optional ways to build this TED pack? Yes. Please read 85-0322-000-OPT for build options. 4. Pages with the descriptor "-ASY" are expected to be followed by the assembly person / assembly house. These are the Construction Notes / Assembly Notes pages, and are used to convey building instructions. 5. The notes on the -TST pages are expected to be followed by Allegro; product shall not be sold to customers until the steps on the -TST pages are completed. These are test and verification steps, and are used to test assembly(s) prior to usage and/or selling. They are not "calibration" procedures as used on production equipment. 6. All photos provided are for reference only; slight variations may result from component second sourcing or later design changes. Photos are intended to convey roughly what completed assembly should look like. 7. As multiple boards exist under this TED pack number (85-0322), there is no -000 assembly. 8. All boards use the -000-ASY Assembly Instructions.

ACS7xx Demo Board Build Options Rev 3 85-0322-000-OPT PAGE 1 OF 1 5/28/2008 Originator: Shawn Upton There are several different assemblies listed under this TED pack. Build according to Request Number / Option Number / Description / TBD, as explained below: # Request: Build (1) each of these: Description: 1 ACS712ELC-05B-T 85-0322-010 ACS712ELC-05B-T 85-0322-010 85-0322-010 ACS712ELC-05B-T 2 ACS712ELC-20A-T 85-0322-011 ACS712ELC-20A-T 85-0322-011 85-0322-011 ACS712ELC-20A-T 3 ACS712ELC-30A-T 85-0322-012 ACS712ELC-30A-T 85-0322-012 85-0322-012 ACS712ELC-30A-T 4 ACS713ELC-20A-T 85-0322-013 ACS713ELC-20A-T 85-0322-013 85-0322-013 ACS713ELC-20A-T 5 ACS713ELC-30A-T 85-0322-014 ACS713ELC-30A-T 85-0322-014 85-0322-014 ACS713ELC-30A-T All boards must be labeled after construction (see -000-ASY)

ACS7xx Demo Board Test and Verification Rev 3 85-0322-000-TST Page 1 of 1 5/28/2008 Originator: Shawn Upton 1. These boards do not require testing prior to shipping to customers.

ACS7xx Demo Board Assembly Instructions Rev 4 85-0322-000-ASY Page 1 of 1 1/7/2009 Originator: Shawn Upton 1. All 85-0322 assemblies require a sticker to be applied post-construction. This sticker shall be applied by whomever constructs the boards. This sticker shall be as such: # Allegro Part: Label 1 85-0322-010 ACS712ELC-05B-T ASEK712ELC-05B-T 2 85-0322-011 ACS712ELC-20A-T ASEK712ELC-20A-T 3 85-0322-012 ACS712ELC-30A-T ASEK712ELC-30A-T 4 85-0322-013 ACS713ELC-20A-T ASEK713ELC-20A-T 5 85-0322-014 ACS713ELC-30A-T ASEK713ELC-30A-T 2. This sticker may be applied onto the top of the board, if it can be. If the sticker is topside, it shall be located between U1 and the silkscreen text "Current Sensor". This is if it will fit, without overlaying any silkscreen text or solderpads. If the sticker is larger than that area, the sticker shall be located on the backside of the PCB. 3. Any sticker applied by the assembly house (not of the type above) shall be installed on the backside of the pcb. [This may be a tracking number, or the assembly house P/N.] The label shall not cover any holes used for soldering. 4. The Allegro sensor may be installed at any time. That is, all the parts required to build an 85-0322-010 (for example) may be installed at the same time. 5. RJ: 22g jumper. Use 22g buss wire, 0.5 inch body, with 0.25 inch leads bent 90 degree. Install 0.125 inch above PCB (not critical). Solder and trim. This component will be used for scope ground clips. 0.5" LS 0.25" leads Intial bending: 0.125" above PCB 6. It is recommended that the SMT parts be installed first, then thro-hole, then banana jacks and standoffs, lastly the sticker(s). Any order of operations may be performed, however.

ACS7xx Demo Board Construction Notes Rev 2 85-0322-000-NTS Page 1 of 1 9/21/2006 Originator: Shawn Upton All components and assembly practices must be RoHS Compliant Certificates of RoHS compliance must be sent to Allegro for record keeping To Install RJ: use buss wire, approx 22-24g. Bend a 1 inch length to 0.5 inch lead spacing, just like as if forming leads for a conventional resistor. Install approximately 0.25 inch above the PCB. This jumper is scope ground clips and must have ample space under it! 85-0322 Rev A.xls

1 2 3 4 IP- A A U1 1 8 IP+ IP+ VCC R1 2 7 IP+ VIout Vout 3 6 CF IP- N/C zero ohm 4 5 C4 IP- GND DNI ACS7xx AGND C5 TP5 DNI AGND AGND +Vin U2 1 +5.0 Vin B AGND 2 GND Vout 5 B C1 3 On/OFF 10uF C2 C3 LP2980AIM5-5 10uF 0.1uF AGND AGND AGND TP1 +Vin J1 +Vin TP2 L1 1 +5.0 +5.0 INDUCTOR AGND 23 TP3 AGND Vout CF 4 TP4 5 Vout 6 Molex 22-11-2061 C RJ C AGND AGND JB1 zero ohm IP+ H1 0 BANANA JACK JB2 4-40 MOUNTING HOLE H2 0 IP- 4-40 MOUNTING HOLE BANANA JACK H3 TP1 - TP4: Testpoints for 0.063 hole: Keystone Electronics 5005 or equivalent JB3 0 JB1 - JB4: use Johnson Components 111-2223-001 Banana jack C1, C2: 1206 16V 10uF: Panasonice ECJ-HVB1C106M 4-40 MOUNTING HOLE C3: 0603 16V 0.1uF: Panasonic ECJ-1VB1C104K GND H4 L1: 0603 Murata BLM18BB471SN1D 0 R1: 0603 zero ohm: Panasonic ERJ-3GEY0R00V BANANA JACK RJ: Use buss wire, 0.5inch long and 0.25inch above PCB D JB4 4-40 MOUNTING HOLE RoHS/Pb-free Label D Logo Title ACS7xx Demo Board GND Allegro Logo Size: A Number: 85-0322-000-SCH Revision:2 Allegro MicroSystems, Inc 955 Perimeter Rd BANANA JACK ALLEGRO LOGO Date: 9/21/2006 Time: 2:29:13 PM Sheet1 of 1 Manchester NH 03103 File: C:\Documents and Settings\supton\My Documents\DXP\85-0322\85-0322 Rev 2.SchDoc 1 2 3 4

None

None

None

None

None

None

None

None

ACS7xx Demo Board Bill of Materials Rev 3 85-0322-001-BOM Page 1 of 3 5/28/2008 Originator: Shawn Upton ITEM QTY S Manufacturer P/N DESCRIPTION REF 1 2 6 Panasonic ECJ-HVB1C106M capacitor, monolythic, 1206, X5R, 10uF, 16V C1, C2 2 1 6 Panasonic ECJ-1VB1C104K capacitor, monolythic, 0603, X5R, 0.1uF, 16V C3 3 Do Not Install C4, C5 4 1 6 Panasonic ERJ-3GEY0R00V resistor, metal film, 0603, 5%, zero ohm R1 5 1 6 Murata BLM18BB471SN1D inductor, 0603 L1 6 1 10 National Semi LP2980AIM5-5.0 IC, voltage regulator, 5V, SOT-23-5 U2 7 4 10 Johnson Components 111-2223-001 connector, banana plug IP+, IP-, IPGND, IPGND 8 5 10 Keystone Electronics 5005K testpoint, 0.063 inch diameter, red TP1 through TP5 9 4 screw, zinc metal plated, 4-40, 0.5 inch, Philips see construction notes 10 4 6 Keystone Electronics 1450C standoff, male/male, zinc metal plated, 4-40, see construction notes 0.5 inch long, hex shaped 11 1 10 Molex 22-11-2062 connector, friction lock header, 6 pin J1 12 1 buss wire, tinned, 22 or 24 gauge RJ 0.5 inch long. See construction notes 13 1 10 PCB, as from gerber files marked "85-0322" 14 1 10 Allegro Current Sensor IC, SOIC8, as provided by Allegro U1 All components and assembly practices must be RoHS Compliant Certificates of RoHS compliance must be sent to Allegro for record keeping

ACS7xx Demo Board Bill of Materials Rev 3 85-0322-001-BOM Page 2 of 3 5/28/2008 Originator: Shawn Upton BOM Explanation Item: each distinct component has a "line item" (but may span multiple lines). When questions arise to a component parameter/designation/etc, please refer to line item number first when inquiring. QTY: the quantity of items to be ordered per finished assembly. Note: higher level documents may call this BOM multiple times S: BOM Substitution Instructions. See below Manufacturer: Recommended (or required) Manufacturer for the part(s). Note: multiple manufacturers may be listed per line item. Note: if no manufacturer part number is given, the the item is considered generic enough that that any manufacturer should work. Ie, 1N4001 in a DO-41 P/N: The manufacturers part number. Note: if multiple manufacturers are listed, this P/N will correspond only to the manufacturer to the immediate left of the P/N Note: Manufacturer part number may be incomplete; if not enough information is given, see below. Description: this is a generic description of the part. Package size, part type, minimum/maximum requirements are listed. Note: this is generic and may not exactly reflect the suggested/required part. For example, "capacitor, 25V" while the manufacturer P/N is actually 50V. The capacitor is required to a minimum of 25V rated (important only if second sourcing) Ref: This is the list of component designators. If "see construction notes" is listed, the construction notes must be used to determine component location (not marked on board etc) Note: surface mount components may have a designator listed but not marked on PCB silkscreen; if so then refer to -CPG (or similar) drawing for location and/or the pick and place file (as found in the gerber files) If a line item has multiple part numbers, they are not to be interpreted as any order of preference If a line item has multiple part numbers, and the substitution code is 10, then only use parts as listed. Mixing is allowed (for example, if 2 manufacturers are listed, and qty is 5, then 2 parts may be from vendor A and 3 parts from vendor B) regardless of code. BOM Substitution Notes: The third column nomenclature is to be used for second sourcing components as follows: 1. Any substitution allowed, as long as mechanically identical (non-electrical items only) (visually different ok) 2. Any susbstitution allowed, as long as mechanically similar (non-electrical items only) (visually different ok) 3. Any substitution, as long as mechanically and visually identical (non-electrical items only) 4. Any substitution allowed, as long as mechanically and visually similar (non-electrical items only) 5. Any substitution allowed, as long as mechanically and visually identical and electrically similar 6. Any substitution allowed, as long as mechanically, electrically and visually similar 7. Reserved for future usage. 8. Reserved for future usage 9. Substitution not recommended, but allowed if mechanically, electrically and visually similar. Only substitute if no alternative. 10. No substitution allowed. "Identical" is to be interpreted as "meeting the same specifications" with no deviation from the specifications. If no manufacturer is given, then do not deviate from stated specifications in the Description field. If a manufacturer is given, do not deviate from the specifications from the manufacturer--the Description field is for reference only then. "Similar" is to be interpreted as "meeting or exceeding the stated specifications, in regards to electrical and/or mechanical parameters (see Substitution code).

ACS7xx Demo Board Bill of Materials Rev 3 85-0322-001-BOM Page 3 of 3 5/28/2008 Originator: Shawn Upton If no manufacturer is given, then do not deviate from stated specifications in the Description field. If a manufacturer is given, do not deviate from the specifications from the manufacturer--the Description field is for reference only then. "Similar" as applied to visual means different colors may be used, unless otherwise noted. For example, an item with Substitution code 6 can typically be any color. However, if the description states "red" and the substitution code is 4, 6 or similar, then a red item must be used--but it may be any shade of red. For example, if a capacitor is to be "identical", it must have the same voltage and tempco etc ratings as stated in the description. If a capacitor is to be similar, the voltage rating may be higher, the tempco lower, etc. Unless if the Substitution code is 10, "identical" parts may be sourced from different manufacturers and may have slight differences in appearance. These subtle differences are ok. Substituting for "Similar" parts: Capacitors: -tempco must be same or go down. Alternately, go up in this order: Z5U, X5R, X7R, NP0, C0G -tolerance must be same or go down -voltage rating must be same or go up -unless otherwise stated, capacitance value must be identical -unless otherwise stated, lead spacing must be same; external dimensions must be the same or smaller Resistors: -tempco must same or go down -tolerance must be same or go down -unless otherwise stated, resistance value must be identical Note: when going from 5% to 1%, use nearest value size -power dissapation must be same or greater -unless otherwise stated, package size must be the same -unless otherwise stated, coloring and marking can vary Diodes and Transistors: -unless otherwise stated, package size must be the same IC's, Connectors, and all other parts:: -unless otherwise stated, package size must be the same (DIP16, SOIC-8, etc) Manufacturer Part Number Discrepencies Every attempt will be made to provide a workable part number. However, prefixes and suffixes can vary over time. If second sourcing from a different manufacturer, make sure that the requirements as noted under the Description column are met. In general, if temperature option(s) are not noted, parts specified to work from 0-85C will be sufficent. If package information is not given, please check the manufacturer datasheet for package type. Any and all descrepencies should be reported to Allegro MicroSystems for correction and updates.

ACS7xx Demo Board Bill of Materials Rev 3 85-0322-010-BOM Page 1 of 1 5/28/2008 Originator: Shawn Upton ITEM QTY S Manufacturer P/N DESCRIPTION REF 1 1 10 Allegro 85-0322-001 board 2 1 10 Allegro ACS712ELC-05B-T IC, SOIC8, current sensor U1 All components and assembly practices must be RoHS Compliant Certificates of RoHS compliance must be sent to Allegro for record keeping

ACS7xx Demo Board Bill of Materials Rev 3 85-0322-011-BOM Page 1 of 1 5/28/2008 Originator: Shawn Upton ITEM QTY S Manufacturer P/N DESCRIPTION REF 1 1 10 Allegro 85-0322-001 board 2 1 10 Allegro ACS712ELC-20A-T IC, SOIC8, current sensor U1 All components and assembly practices must be RoHS Compliant Certificates of RoHS compliance must be sent to Allegro for record keeping

ACS7xx Demo Board Bill of Materials Rev 3 85-0322-012-BOM Page 1 of 1 5/28/2008 Originator: Shawn Upton ITEM QTY S Manufacturer P/N DESCRIPTION REF 1 1 10 Allegro 85-0322-001 board 2 1 10 Allegro ACS712ELC-30A-T IC, SOIC8, current sensor U1 All components and assembly practices must be RoHS Compliant Certificates of RoHS compliance must be sent to Allegro for record keeping

ACS7xx Demo Board Bill of Materials Rev 3 85-0322-013-BOM Page 1 of 1 5/28/2008 Originator: Shawn Upton ITEM QTY S Manufacturer P/N DESCRIPTION REF 1 1 10 Allegro 85-0322-001 board 2 1 10 Allegro ACS713ELC-20A-T IC, SOIC8, current sensor U1 All components and assembly practices must be RoHS Compliant Certificates of RoHS compliance must be sent to Allegro for record keeping

ACS7xx Demo Board Bill of Materials Rev 3 85-0322-014-BOM Page 1 of 1 5/28/2008 Originator: Shawn Upton ITEM QTY S Manufacturer P/N DESCRIPTION REF 1 1 10 Allegro 85-0322-001 board 2 1 10 Allegro ACS713ELC-30A-T IC, SOIC8, current sensor U1 All components and assembly practices must be RoHS Compliant Certificates of RoHS compliance must be sent to Allegro for record keeping