CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Surface Mount PXH NPCAPTM- Series ・Super low ESR, impedance and high heat resistance have been obtained by using con- ductive polymer as electrolyte. PXH ・Suitable for DC-DC converters, voltage regulators and decoupling applications. ・Endurance : 125℃ 1,000 hours ・Rated voltage range : 2.5 to 20Vdc, Capacitance range : 22 to 1,000μF Higher temperature ・Case size range :φ6.3×5.7L to φ10×7.7L PXA ・Solvent resistant type (see PRECAUTIONS AND GUIDELINES) ・RoHS2 Compliant ・Halogen Free ◆SPECIFICATIONS Items Characteristics Category -55 to +125℃ Temperature Range Rated Voltage Range 2.5 to 20Vdc Capacitance Tolerance ±20% (M) (at 20℃, 120Hz) Leakage Current Shall not exceed values shown in STANDARD RATINGS. *Note (at 20℃ after 2 minutes) Dissipation Factor 0.12 max. (tanδ) (at 20℃, 120Hz) Low Temperature Z(-25℃)/Z(+20℃)≦1.15 Characteristics (Max. Impedance Ratio) Z(-55℃)/Z(+20℃)≦1.25 (at 100kHz) Endurance The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 1,000 hours at 125℃. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦200% of the initial specified value ESR ≦200% of the initial specified value Leakage current ≦The initial specified value Bias Humidity The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to the DC rated voltage at 60℃, 90 to 95% RH for 1,000 hours. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦150% of the initial specified value ESR ≦150% of the initial specified value Leakage current ≦The initial specified value Surge Voltage The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 125℃ for 30 seconds through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds. Rated voltage (Vdc) 2.5 4.0 6.3 10 16 20 Surge voltage (Vdc) 2.9 4.6 7.2 12 18 23 Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦150% of the initial specified value ESR ≦150% of the initial specified value Leakage current ≦The initial specified value Soldering Heat The following specifications shall be satisfied when the solder temperature is reduced back to 20°C to measure dip resistance after soldering has been performed under the recommended soldering conditions. Appearance No significant damage Capacitance value Within the specified tolerance range D.F. (tanδ) ≦The initial specified value ESR ≦The initial specified value Leakage current ≦The initial specified value (Voltage treatment) Failure Rate 0.5% per 1,000 hours maximum (Confidence level 60% at 125℃) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 125℃. ◆DIMENSIONS [mm] ◆MARKING EX) 20V22µF ●Terminal Code : A W H39F 22 0.5± 0.2± P 0.2± Size code φD L A B C W P 20V Dφ B C F60 6.3 5.7 6.6 6.6 7.2 0.5 to 0.8 1.9 H70 8 6.7 8.3 8.3 9.0 0.7 to 1.1 3.1 J80 10 7.7 10.3 10.3 11.0 0.7 to 1.1 4.5 0.3max. A±0.2 L±0.3 Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. CAT. No. E1001U

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Surface Mount PXH NPCAPTM- Series ◆PART NUMBERING SYSTEM 1 2 3 4 5 6 7 89 10 11 12 13 14 15 16 17 18 A PXH A RA M G Supplement code Size code Capacitance tolerance code Capacitance code (ex. 22µF:220,100µF:101) Taping code Terminal code Voltage code (ex. 6.3V:6R3,10V:100) Series code Category Please refer to "Product code guide (conductive polymer type)" ◆STANDARD RATINGS Rated ripple current WV Cap Size code Leakage current ESR (mArms/100kHz) Part No. (Vdc) (µF) (µA max./after 2min.) (mΩ max./20℃, 100k to 300kHz) -55℃≦Tx≦+105℃*1 +105℃＜Tx≦+125℃*1 220 F60 110 35 2,500 770 APXH2R5ARA221MF60G 2.5 560 H70 280 30 3,100 960 APXH2R5ARA561MH70G 1,000 J80 500 25 3,700 1,100 APXH2R5ARA102MJ80G 150 F60 120 35 2,450 770 APXH4R0ARA151MF60G 4 220 H70 176 30 3,020 960 APXH4R0ARA221MH70G 680 J80 544 25 3,700 1,100 APXH4R0ARA681MJ80G 82 F60 103 40 2,400 720 APXH6R3ARA820MF60G 100 F60 126 40 2,400 720 APXH6R3ARA101MF60G 6.3 150 H70 189 30 3,020 960 APXH6R3ARA151MH70G 220 H70 277 30 3,020 960 APXH6R3ARA221MH70G 470 J80 592 25 3,700 1,100 APXH6R3ARA471MJ80G 56 F60 112 45 2,250 680 APXH100ARA560MF60G 120 H70 240 35 2,800 880 APXH100ARA121MH70G 10 150 H70 300 35 2,800 880 APXH100ARA151MH70G 330 J80 660 30 3,700 1,010 APXH100ARA331MJ80G 39 F60 125 50 2,050 650 APXH160ARA390MF60G 82 H70 262 40 2,700 830 APXH160ARA820MH70G 16 150 J80 480 35 3,020 930 APXH160ARA151MJ80G 180 J80 576 35 3,020 930 APXH160ARA181MJ80G 22 F60 88.0 60 1,650 590 APXH200ARA220MF60G 20 47 H70 188 45 2,000 780 APXH200ARA470MH70G 82 J80 328 45 2,400 820 APXH200ARA820MJ80G *1　Tx : Ambient temperature（℃） ◆RATED RIPPLE CURRENT MULTIPLIERS ・Frequency Multipliers Frequency（Hz） 120 1k 10k 50k 100k to 500k 2.5 to 6.3Vdc 0.05 0.30 0.55 0.70 1.00 10 to 20Vdc 0.05 0.25 0.55 0.55 1.00 Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. CAT. No. E1001U