AFBR-5701Z and AFBR-5705Z Families of Multi-Mode Small Form Factor Pluggable (SFP) Optical Transceivers with Optional DMI for Gigabit Ethernet (1.25 GBd) and Fibre Channel (1.0625 GBd) Data Sheet Description Features The AFBR-570xZ family of SFP optical transceivers offers • ROHS-6 Compliant the customer a wide range of design options, including • Compliant to IEEE 802.3 Gigabit Ethernet (1.25GBd) optional DMI features (further described later), two 1000BaseSX & Fiber Channel FC-PI 100-M5-SN-I & 100- temperature ranges (extended or industrial), and choice M6-SN-I of standard or bail delatch. The AFBR-5705Z family • Optional Digital Diagnostic Monitoring available targets those applications requiring DMI features. The - AFBR-5701Z family: without DMI AFBR-5701Z family is a streamlined product designed - AFBR-5705Z family: with DMI for those applications where DMI features are not • Per SFF-8472, diagnostic features on AFBR-5705Z family needed. Throughout this document, AFBR-570xZ will enable Diagnostic Monitoring Interface for optical be used to refer collectively to the product family transceivers with real-time monitoring of: encompassing this entire range of product options. - Transmitted optical power Part Number Options - Received optical power - Laser bias current The AFBR-570xZ SFP family includes the following - Temperature products: - Supply voltage Part Number DMI Temperature Latch • Transceiver specifications according to SFP Multi-Source AFBR-5701LZ No Extended Standard Agreement (SFF-8074i) and SFF-8472, Revision 9.3 AFBR-5701PZ No Extended Bail • Manufactured in an ISO 9001 compliant facility AFBR-5701ALZ No Industrial Standard • Hot-pluggable AFBR-5701APZ No Industrial Bail • Temperature options AFBR-5705LZ Yes Extended Standard - (Extended) -10°C to +85°C AFBR-5705PZ Yes Extended Bail - (Industrial) -40°C to +85°C AFBR-5705ALZ Yes Industrial Standard • +3.3 V DC power supply AFBR-5705APZ Yes Industrial Bail • Industry leading EMI performance for high port density • 850 nm Vertical Cavity Surface Emitting Laser (VCSEL) * Extended Temperature Range is -10 to 85 °C Industrial Temperature Range is -40 to 85 ° C • Eye safety certified • LC-Duplex fiber connector compliant Related Products Applications • AFBR-5715Z family: 1.25 GBd Ethernet (1000BASE-SX) SFP with DMI • Ethernet Switch • AFBR-5710Z family : 1.25 GBd Ethernet (1000BASE-SX) • Enterprise Router SFP without DMI • Broadband aggregation and wireless infrastructure • AFCT-5705Z family: 1.25 GBd Ethernet (1000BASE-LX) & • Storage applications including Fiber Channel and iSCSCI 1.0265 GBd Fiber-Channel SFP with DMI • AFCT-5701Z family: 1.25 GBd Ethernet (1000BASE-LX) & 1.0265 GBd Fiber-Channel SFP without DMI

OPTICAL INTERFACE ELECTRICAL INTERFACE RECEIVER RD+ (RECEIVE DATA) AMPLIFICATION LIGHT FROM FIBER PHOTO-DETECTOR & QUANTIZATION RD(cid:151) (RECEIVE DATA) Rx LOSS OF SIGNAL MOD-DEF2 (SDA) CONTROLLER & MEMORY MOD-DEF1 (SCL) MOD-DEF0 TRANSMITTER TX_DISABLE LASER DRIVER & TD+ (TRANSMIT DATA) LIGHT TO FIBER VCSEL SAFETY TD(cid:151) (TRANSMIT DATA) CIRCUITRY TX_FAULT Figure 1. SFP Block Diagram Overview 3 2 1 3 2 1 ENGAGEMENT The AFBR-570xZ family of optical transceivers are 20 VEET SEQUENCE 1 VEET compliant with the specifications set forth in the 19 TD– 2 TX FAULT IEEE802.3 (1000BASE-SX), Fibre Channel (100-M5-SN-I, 100-M6-SN-I), and the Small Form-Factor Pluggable 18 TD+ 3 TX DISABLE (SFP) Multi-Source Agreement (MSA). This family of transceivers is qualified in accordance with Telcordia 17 VEET 4 MOD-DEF(2) GR-468-CORE. Its primary application is servicing Gigabit 16 VCCT 5 MOD-DEF(1) Ethernet and Fibre Channel links between optical networking equipment. 15 VCCR 6 MOD-DEF(0) The AFBR-570xZ offers maximum flexibility to designers, 14 VEER 7 RATE SELECT manufacturers, and operators of Gigabit Ethernet 13 RD+ 8 LOS networking equipment. A pluggable architecture allows the module to be installed into MSA standard SFP ports at any 12 RD– 9 VEER time – even with the host equipment operating and online. This facilitates the rapid configuration of equipment to 11 VEER 10 VEER precisely the user’s needs – reducing inventory costs and TOP OF BOARD BOTTOM OF BOARD network downtime. Compared with traditional transceivers, (AS VIEWED THROUGH TOP OF BOARD) the size of the Small Form Factor package enables higher port densities. Figure 2. Pin description of the SFP electrical interface. Module Diagrams Figure 1 illustrates the major functional components of the AFBR-570xZ. The external configuration of the module is depicted in Figure 7. Figure 8 depicts the panel and host board footprints. 2

Installation Transmit Fault (Tx_Fault) The AFBR-570xZ can be installed in or removed from any A catastrophic laser fault will activate the transmitter signal, MSA-compliant Pluggable Small Form Factor port TX_FAULT, and disable the laser. This signal is an open regardless of whether the host equipment is operating or collector output (pull-up required on the host board). A not. The module is simply inserted, electrical-interface first, low signal indicates normal laser operation and a high under finger-pressure. Controlled hot-plugging is ensured signal indicates a fault. The TX_FAULT will be latched high by 3-stage pin sequencing at the electrical interface. This when a laser fault occurs and is cleared by toggling the printed circuit board card-edge connector is depicted in TX_DISABLE input or power cycling the transceiver. The Figure 2. transmitter fault condition can also be monitored via the 2-wire serial interface (address A2, byte 110, bit 2). As the module is inserted, first contact is made by the housing ground shield, discharging any potentially Eye Safety Circuit component-damaging static electricity. Ground pins The AFBR-570xZ provides Class 1 eye safety by design engage next and are followed by Tx and Rx power supplies. and has been tested for compliance with the requirements Finally, signal lines are connected. Pin functions and listed in Table 1. The eye safety circuit continuously sequencing are listed in Table 2. monitors optical output power levels and will disable the Transmitter Section transmitter and assert a TX_FAULT signal upon detecting an unsafe condition. Such unsafe conditions can be created The transmitter section includes the Transmitter Optical by inputs from the host board (Vcc fluxuation, unbalanced Subassembly (TOSA) and laser driver circuitry. The TOSA, code) or faults within the module. containing an 850 nm VCSEL (Vertical Cavity Surface Emitting Laser) light source, is located at the optical Receiver Section interface and mates with the LC optical connector. The The receiver section includes the Receiver Optical TOSA is driven by a custom IC, which converts differential Subassembly (ROSA) and amplification/quantization logic signals into an analog laser diode drive current. This circuitry. The ROSA, containing a PIN photodiode and Tx driver circuit regulates the optical power at a constant custom trans-impedance preamplifier, is located at the level provided the data pattern is DC balanced (8B10B optical interface and mates with the LC optical connector. code for example). The ROSA is mated to a custom IC that provides post- Transmit Disable (Tx_Disable) amplification and quantization. Also included is a Loss Of Signal (LOS) detection circuit. The AFBR-570xZ accepts a TTL and CMOS compatible transmit disable control signal input (pin 3) which shuts Receiver Loss of Signal (Rx_LOS) down the transmitter optical output. A high signal The Loss Of Signal (LOS) output indicates an unusable implements this function while a low signal allows normal optical input power level. The Loss Of Signal thresholds transceiver operation. In the event of a fault (e.g. eye safety are set to indicate a definite optical fault has occurred circuit activated), cycling this control signal resets the (e.g., disconnected or broken fiber connection to module as depicted in Figure 6. An internal pull-up resistor receiver, failed transmitter, etc.). disables the transceiver transmitter until the host pulls the input low. Host systems should allow a 10ms interval The post-amplification IC includes transition detection between successive assertions of this control signal. circuitry which monitors the ac level of incoming optical Tx_Disable can also be asserted via the 2-wire serial signals and provides a TTL/CMOS compatible status interface (address A2h, byte 110, bit 6) and monitored signal to the host (pin 8). An adequate optical input (address A2h, byte 110, bit 7). results in a low Rx_LOS output while a high Rx_LOS output indicates an unusable optical input. The Rx_LOS The contents of A2h, byte 110, bit 6 are logic OR’d with thresholds are factory-set so that a high output indicates hardware Tx_Disable (pin 3) to control transmitter a definite optical fault has occurred. For the AFBR-5705Z operation. family, Rx_LOS can also be monitored via the 2-wire serial interface (address A2h, byte 110, bit 1). 3

Functional I/O Digital Diagnostic Interface and Serial Identification (EEPROM) The AFBR-570xZ accepts industry standard differential signals such as LVPECL and CML within the scope of the The entire AFBR-570xZ family complies with the SFF- SFP MSA. To simplify board requirements, transmitter 8074i SFP specification. The AFBR-5705Z family further bias resistors and ac coupling capacitors are complies with SFF-8472, the SFP specification for Digital incorporated, per SFF-8074i, and hence are not required Diagnostic Monitoring Interface. Both specifications can on the host board. The module is AC-coupled and be found at http://www.sffcommittee.org. internally terminated. The AFBR-570xZ features an EEPROM for Serial ID, which Figure 3 illustrates a recommended interface circuit to contains the product data stored for retrieval by host link the AFBR-570xZ to the supporting Physical Layer equipment. This data is accessed via the 2-wire serial integrated circuits. EEPROM protocol of the ATMEL AT24C01A or similar, in compliance with the industry standard SFP Multi-Source Timing diagrams for the MSA compliant control signals Agreement. The base EEPROM memory, bytes 0-255 at implemented in this module are depicted in Figure 6. memory address 0xA0, is organized in compliance with The AFBR-570xZ interfaces with the host circuit board SFF-8074i. Contents of this serial ID memory are shown through twenty I/O pins (SFP electrical connector) in Table 10. identified by function in Table 2. The AFBR-570xZ high speed transmit and receive interfaces require SFP MSA compliant signal lines on the host board. The Tx_Disable, Tx_Fault, and Rx_LOS lines require TTL lines on the host board (per SFF-8074i) if used. If an application chooses not to take advantage of the functionality of these pins, care must be taken to ground Tx_Disable (for normal operation). 1 µH VCCT,R HOUSING 10 µF 0.1 µF 1 µH GROUND VCCT AVAGO *RES AFBR-570xZ 0.1 µF *RES TX_DISABLE GP04 TX_FAULT TX_FAULT VREFR 50 Ω TD+ SO1+ C R LASER DRIVER TX[0:9] 50 Ω C & EYE SAFETY SO1– TD– CIRCUITRY TBC SYNC VEET EWRAP LOOP AVAGO VCCR MAC HDMP-1687 10 0.1 ASIC RX[0:9] µF µF 50 Ω RD+ SYN1 SI1+ RX_RRABTCE RRCC1M(00:1) SI1– R 50 Ω CC RD– AMPLIF&ICATION RFCT QUANTIZATION RX_LOS VCCT,R REF_RATE *RES *RES *RES *RES RX_LOS GPIO(X) GPIO(X) MOD_DEF2 GP14 MOD_DEF1 EEPROM REFCLK MOD_DEF0 125 MHz VEER NOTE: * 4.7 k Ω < RES < 10 kΩ Figure 3. Typical application configuration. 4

As an enhancement to the conventional SFP interface potential component compliance issues. Received defined in SFF-8074i, the AFBR-5705Z family is compliant optical power is also available to assess compliance of a to SFF-8472 (digital diagnostic interface for optical cable plant and remote transmitter. When operating out transceivers). This new digital diagnostic information is of requirements, the link cannot guarantee error free stored in bytes 0-255 at memory address 0xA2.Using transmission. the 2-wire serial interface defined in the MSA, the AFBR- Fault Isolation 5705Z provides real time temperature, supply voltage, laser bias current, laser average output power and The fault isolation feature allows a host to quickly received input power. These parameters are internally pinpoint the location of a link failure, minimizing calibrated, per the MSA. downtime. For optical links, the ability to identify a fault at a local device, remote device or cable plant is crucial The digital diagnostic interface also adds the ability to to speeding service of an installation. AFBR-5705Z real- disable the transmitter (TX_DISABLE), monitor for time monitors of Tx_Bias, Tx_Power, Vcc, Temperature Transmitter Faults (TX_FAULT), and monitor for Receiver and Rx_Power can be used to assess local transceiver Loss of Signal (RX_LOS). current operating conditions. In addition, status flags The new diagnostic information provides the Tx_Disable and Rx Loss of Signal (LOS) are mirrored in opportunity for Predictive Failure Identification, memory and available via the two-wire serial interface. Compliance Prediction, Fault Isolation and Component Component Monitoring Monitoring. Component evaluation is a more casual use of the Predictive Failure Identification AFBR-5705Z real-time monitors of Tx_Bias, Tx_Power, The predictive failure feature allows a host to identify Vcc, Temperature and Rx_Power. Potential uses are as potential link problems before system performance is debugging aids for system installation and design, and impacted. Prior identification of link problems enables transceiver parametric evaluation for factory or field a host to service an application via “fail over” to a qualification. For example, temperature per module can redundant link or replace a suspect device, maintaining be observed in high density applications to facilitate system uptime in the process. For applications where thermal evaluation of blades, PCI cards and systems. ultra-high system uptime is required, a digital SFP Required Host Board Components provides a means to monitor two real-time laser metrics associated with observing laser degradation and The MSA power supply noise rejection filter is required predicting failure: average laser bias current (Tx_Bias) on the host PCB to meet data sheet performance. The and average laser optical power (Tx_Power). MSA filter incorporates an inductor which should be rated 400 mADC and 1 Ω series resistance or better. It Compliance Prediction should not be replaced with a ferrite. The required filter Compliance prediction is the ability to determine if an is illustrated in Figure 4. optical transceiver is operating within its operating and The MSA also specifies that 4.7 K to 10 KΩ pull-up environmental requirements. AFBR-5705Z devices resistors for TX_FAULT, LOS, and MOD_DEF0,1,2 are provide real-time access to transceiver internal supply required on the host PCB. voltage and temperature, allowing a host to identify 1 µH V T CC 0.1 µF 1 µH V R 3.3 V CC 0.1 µF 10 µF 0.1 µF 10 µF SFP MODULE HOST BOARD Figure 4. MSA required power supply filter. 5

Fiber Compatibility The AFBR-570xZ transciever is capable of transmission precautions. These precautions include using grounded at 2 to 550 meters with 50/125 µm fiber, and at 2 to wrist straps, work benches, and floor mats in ESD 275 meters with 62.5 125 µm fiber, for 1.25 GBd controlled areas. The ESD sensitivity of the AFBR-570xZ Ethernet. It is capable of transmission up to 500m with is compatible with typical industry production 50/125 µm fiber and up to 300m with 62.5/125 µm environments. fiber, for 1.0625 GBd Fiber Channel. The second case to consider is static discharges to the Application Support exterior of the host equipment chassis after installation. To the extent that the optical interface is exposed to To assist in the transceiver evaluation process, Agilent the outside of the host equipment chassis, it may be offers a 1.25 Gbd Gigabit Ethernet evaluation board subject to system-level ESD requirements. which facilitates testing of the AFBR-570xZ. It can be obtained through the Agilent Field Organization by Electromagnetic Interference (EMI) referencing Agilent part number HFBR-0571. Equipment using the AFBR-570xZ family of transceivers A Reference Design including the AFBR-570xZ and the is typically required to meet the requirements of the HDMP-1687 GigaBit Quad SerDes is available. It may FCC in the United States, CENELEC EN55022 (CISPR 22) be obtained through the Agilent Field Sales in Europe, and VCCI in Japan. organization. The metal housing and shielded design of the AFBR- Regulatory Compliance 570xZ minimize the EMI challenge facing the host equipment designer. See Table 1 for transceiver Regulatory Compliance. Certification level is dependent on the overall EMI Immunity configuration of the host equipment. The transceiver Equipment hosting AFBR-570xZ modules will be performance is offered as a figure of merit to assist the subjected to radio-frequency electromagnetic fields in designer. some environments. The transceiver has excellent Electrostatic Discharge (ESD) immunity to such fields due to its shielded design. The AFBR-570xZ exceeds typical industry standards Flammability and is compatible with ESD levels found in typical The AFBR-570xZ transceiver is made of metal and high manufacturing and operating environments as strength, heat resistant, chemically resistant, and UL described in Table 1. 94V-0 flame retardant plastic. There are two design cases in which immunity to ESD Customer Manufacturing Processes damage is important. This module is pluggable and is not designed for The first case is during handling of the transceiver prior aqueous wash, IR reflow, or wave soldering processes. to insertion into the transceiver port. To protect the transceiver, it’s important to use normal ESD handling 6

Table 1. Regulatory Compliance Feature Test Method Performance Electrostatic Discharge JEDEC/EIA Class 2 (> +2000 Volts) (ESD)to the Electrical Pins JESD22-A114-A Electrostatic Discharge Variation of IEC 6100-4-2 Typically withstands at least 25 kV without (ESD) to the Duplex LC damage when the duplex LC connector Reseptacle receptacle is contacted by a Human Body Model probe Electromagnetic FCC Class B CENELEC EN55022 Applications with high SFP port counts are Interference(EMI) Class B (CISPR 22A) VCCI Class 1 expected to be compliant; however, margins are dependent on customer board and chassis design. Immunity Variation of IEC 61000-4-3 Typically shows a negligible effect from a 10 V/m field swept from 80 to 1000 MHz applied to the transceiver without a chassis enclosure. Eye Safety US FDA CDRH AEL Class 1 CDRH certification #9720151-57 EN(IEC)60825-1,2, EN60950 Class 1 TUV file R 72050685 Component Recognition Underwriters Laboratories and Canadian UL File #E173874 Standards Association Joint Component Recognition for Information Technology Equipment Including Electrical Business Equipment ROHS Compliance Less than 1000ppm of: cadmium, lead, mercury, hexavalent chromium, polybrominated biphenyls, and polybrominated biphenyl ethers. Caution There are no user serviceable parts nor any maintenance required for the AFBR-570xZ. All adjustments are made at the factory before shipment to our customers. Tampering with, modifying, misusing or improperly handling the AFBR-570xZ will void the product warranty. It may also result in improper operation of the AFBR-570xZ circuitry, and possible overstress of the laser source. Device degradation or product failure may result. Connection of the AFBR- 570xZ to a non-Gigabit Ethernet compliant or non-Fiber Channel compliant optical source, operating above the recommended absolute maximum conditions or operating the AFBR-570xZ in a manner inconsistent with its design and function may result in hazardous radiation exposure and may be considered an act of modifying or manufacturing a laser product. The person(s) performing such an act is required by law to re-certify and re-identify the laser product under the provisions of U.S. 21 CFR (Subchapter J). 7

Table 2. Pin Description Engagement Pin Name Function/Description Order(insertion) Notes 1 VeeT Transmitter Ground 1 2 TX Fault Transmitter Fault Indication 3 1 3 TX Disable Transmitter Disable - Module disables on high or open 3 2 4 MOD-DEF2 Module Definition 2 - Two wire serial ID interface 3 3 5 MOD-DEF1 Module Definition 1 - Two wire serial ID interface 3 3 6 MOD-DEF0 Module Definition 0 - Grounded in module 3 3 7 Rate Selection Not Connected 3 8 LOS Loss of Signal 3 4 9 VeeR Receiver Ground 1 10 VeeR Receiver Ground 1 11 VeeR Receiver Ground 1 12 RD- Inverse Received Data Out 3 5 13 RD+ Received Data Out 3 5 14 VeeR Reciver Ground 1 15 VccR Receiver Power -3.3 V ±5% 2 6 16 VccT Transmitter Power -3.3 V ±5% 2 6 17 VeeT Transmitter Ground 1 18 TD+ Transmitter Data In 3 7 19 TD- Inverse Transmitter Data In 3 7 20 VeeT Transmitter Ground 1 Notes: 1. TX Fault is an open collector/drain output which should be pulled up externally with a 4.7KΩ – 10 KΩ resistor on the host board to a supply <VccT+0.3 V or VccR+0.3 V. When high, this output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8 V. 2. TX disable input is used to shut down the laser output per the state table below. It is pulled up within the module with a 4.7-10 KΩ resistor. Low (0 – 0.8 V): Transmitter on Between (0.8 V and 2.0 V): Undefined High (2.0 – 3.465 V): Transmitter Disabled Open: Transmitter Disabled 3. Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7-10 KΩ resistor on the host board to a supply less than VccT +0.3 V or VccR+0.3 V. Mod-Def 0 is grounded by the module to indicate that the module is present Mod-Def 1 is clock line of two wire serial interface for optional serial ID Mod-Def 2 is data line of two wire serial interface for optional serial ID 4. LOS (Loss of Signal) is an open collector/drain output which should be pulled up externally with a 4.7 K – 10 KΩ resistor on the host board to a supply < VccT,R+0.3 V. When high, this output indicates the received optical power is below the worst case receiver sensitivity (as defined by the standard in use). Low indicates normal operatio0n. In the low state, the output will be pulled to < 0.8 V. 5. RD-/+: These are the differential receiver outputs. They are AC coupled 100 Ω differential lines which should be terminated with 100 Ω differential at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines must be between 370 and 2000 mV differential (185 – 1000 mV single ended) according to the MSA. Typically it will be 1500mv differential. 6. VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.135 – 3.465 V at the SFP connector pin. The in-rush current will typically be no more than 30 mA above steady state supply current after 500 nanoseconds. 7. TD-/+: These are the differential transmitter inputs. They are AC coupled differential lines with 100 Ω differential termination inside the module. The AC coupling is done inside the module and is thus not required on the host board. The inputs will accept differential swings of 500 – 2400 mV (250 – 1200 mV single ended). However, the applicable recommended differential voltage swing is found in Table 5. 8

Table 3. Absolute Maximum Ratings Parameter Symbol Minimum Maximum Unit Notes Ambient Storage Temperature(Non- operating) Ts -40 +100 °C 1, 2 Case Temperature T -40 +85 °C 1, 2 C Relative Humidity RH 5 95 % 1 Supply Voltage V -0.5 3.8 V 1, 2, 3 CCT,R Low Speed Input Voltage V -0.5 V +0.5 V 1 IN CC Notes: 1. Absolute Maximum Ratings are those values beyond which damage to the device may occur if these limits are exceeded. See Reliability Data Sheet for specific reliability performance. 2. Between Absolute Maximum Ratings and the Recommended Operating Conditions functional performance is not intended, device reliability is not implied, and damage to the device may occur. 3. The module supply voltages, VCCT and VCCR, must not differ by more than 0.5V or damage to the device may occur. Table 4. Recommended Operating Conditions Parameter Symbol Minimum Typical Maximum Unit Notes Case Temperature AFBR-570xLZ/PZ T -10 25 85 °C 1, 2 C AFBR-570xALZ/APZ T -40 25 85 °C 1, 2 C Supply Voltage V 3.135 3.3 3.465 V 1 CC Data Rate 1.0625 1.25 Gb/s 1,3, 4 Notes: 1. Recommended Operating Conditions are those within which functional performance within data sheet characteristics is intended. 2. Refer to the Reliability Data Sheet for specific reliability performance predictions. 3. IEEE802.3 Gigabit Ethernet. 4. ANSIX3.230 (FC-PI). 9

Table 5. Transceiver Electrical Characteristics Parameter Symbol Minimum Typical Maximum Unit Notes Module Supply Current I 160 220 mA CC Power Dissipation P 530 765 mW DISS Power Supply Noise PSNR 100 mV 1 PP Rejection(peak-peak) Data input: V 500 2400 mV 2 I PP Transmitter Differential Input Voltage (TD +/-) Data Output: V 370 1500 2000 mV 3 O PP Receiver Differential Output Voltage (RD +/-) Receive Data Rise & Fall Times T 220 ps RF Low Speed Outputs: V 2.0 V T,R+0.3 V 4 OH CC Transmit Fault (TX_FAULT) Loss V 0 0.8 V of Signal (LOS), MOD_DEF2 OL Low Speed Inputs: V 2.0 V V 5 IH CC Transmitter Disable (TX_DISABLE), MOD_DEF 1, V 0 0.8 V IL MOD_DEF 2 Notes: 1. Measured at the input of the required MSA Filter on host board. 2. Internally AC coupled and terminated to 100 Ω differential load. 3. Internally AC coupled, but requires a 100 Ω differential termination at or internal to Serializer/Deserializer. 4. Pulled up externally with a 4.7-10 KΩ resistor on the host board to VCCT,R. 5. Mod_Def1 and Mod_Def2 must be pulled up externally with a 4.7-10 KΩ resistor on the host board to VCCT,R. 10

Table 6. Transmitter Optical Characteristics Parameter Symbol Minimum Typical Maximum Unit Notes Output Optical Power (Average) P -9.5 -6.5 -3 dBm 1,2,3 OUT Optical Extinction Ratio ER 9 12 dB 1 Center Wavelength λ 830 850 860 nm 1 C Spectral Width - rms σ 0.85 nm 1 Optical Rise/Fall Time (1.25GBd) T 150 260 ps 1 RISE/FALL Optical Rise/Fall Time (1.0625GBd) T 150 300 ps 1,4 RISE/FALL Relative Intensity Noise RIN -117 dB/Hz 1 Total Jitter TJ 227 ps 1 (TP1 to TP2 Contribution 1.25 GBd) 0.284 UI 1 (TP1 to TP2 contribution 1.0625 GBd) 252 ps 4 0.267 UI 4 Deterministic Jitter DJ 85 ps 4 (TP1 to TP2 Contribution 1.0625 GBd) 0.09 UI 4 Pout TX_DISABLE Assorted P -35 dBm 1 OFF Optical Modulation Amplitude OMA 156 µW 4 Notes: 1. IEEE 802.3. 2. Max. Pout is the lesser of 0 dBm or Maximum allowable per Eye Safety Standard. 3. 50/125 µm fiber with NA = 0.2, 62.5/125 µm fiber with NA = 0.275. 4. ANSIX3.230 (FC-PI). NORMALIZED TIME (UNIT INTERVAL) 0 0.22 0.375 0.625 0.78 1.0 130 1.30 %) 100 1.00 PLITUDE ( 80 0.80 MPLITUDE M A A 50 0.50 D D ZE ALIZE 20 0.20 MALI M R OR NO N 0 0 –20 –0.20 0 22 37.5 62.5 78 100 NORMALIZED TIME (% OF UNIT INTERVAL) Figure 5a. Gigabit Ethernet transmitter eye mask diagram Figure 5b. Typical AFBR-570xZ eye mask diagram 11

Table 7. Receiver Optical Characteristics Parameter Symbol Minimum Typical Maximum Unit Notes Optical Input Power P -17 0 dBm 1 R Receiver Sensitivity P -21 -17 dBm 1 RMIN (Optical Input Power) Stressed Receiver Sensitivity -12.5 dBm 1,2 1.25GBd(GBE) -13.5 dBm 1,3 Stressed Receiver Sensitivity 67 µW 2,4 1.0625GBd (FC-PI) OMA 55 µW 3,4 Total Jitter TJ 266 ps 1 (TP3 to TP4 Contribution 1.25GBd) 0.332 UI 1 Total Jitter TJ 205 ps 4 (TP3 to TP4 Contribution 1.0625GBd) 0.218 UI 4 Deterministic Jitter DJ 113 ps 4 (TP3 to TP4 Contribution 1.0625GBd) 0.12 UI 4 Return Loss -12 dB 1 LOS De-Asserted P - -17 dBm 1 D LOS Asserted P -30 dBm 1 A LOS Hysterisis P -P 3 dB 1 D A Optical Modulation Amplitude OMA 31 µW 4 Notes: 1. IEEE 802.3. 2. 62.5/125 µm fiber. 3. 50/125 µm fiber. 4. ANSIX3.230 (FC-PI). 12

Table 8. Transceiver SOFT DIAGNOSTIC Timing Characteristics Parameter Symbol Minimum Maximum Unit Notes Hardware TX_DISABLE Assert Time t_off 10 µs Note 1 Hardware TX_DISABLE Negate Time t_on 1 ms Note 2 Time to initialize, including reset of TX_FAULT t_init 300 ms Note 3 Hardware TX_FAULT Assert Time t_fault 100 µs Note 4 Hardware TX_DISABLE to Reset t_reset 10 µs Note 5 Hardware RX_LOS Assert Time t_loss_on 100 µs Note 6 Hardware RX_LOS De-Assert Time t_loss_off 100 µs Note 7 Software TX_DISABLE Assert Time t_off_soft 100 ms Note 8 Software TX_DISABLE Negate Time t_on_soft 100 ms Note 9 Software Tx_FAULT Assert Time t_fault_soft 100 ms Note 10 Software Rx_LOS Assert Time t_loss_on_soft 100 ms Note 11 Software Rx_LOS De-Assert Time t_loss_off_soft 100 ms Note 12 Analog parameter data ready t_data 1000 ms Note 13 Serial bus hardware ready t_serial 300 ms Note 14 Write Cycle Time t_write 10 ms Note 15 Serial ID Clock Rate f_serial_clock 400 kHz Notes: 1. Time from rising edge of TX_DISABLE to when the optical output falls below 10% of nominal. 2. Time from falling edge of TX_DISABLE to when the modulated optical output rises above 90% of nominal. 3. Time from power on or falling edge of Tx_Disable to when the modulated optical output rises above 90% of nominal. 4. From power on or negation of TX_FAULT using TX_DISABLE. 5. Time TX_DISABLE must be held high to reset the laser fault shutdown circuitry. 6. Time from loss of optical signal to Rx_LOS Assertion. 7. Time from valid optical signal to Rx_LOS De-Assertion. 8. Time from two-wire interface assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the optical output falls below 10% of nominal. Measured from falling clock edge after stop bit of write transaction. 9. Time from two-wire interface de-assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the modulated optical output rises above 90% of nominal. 10.Time from fault to two-wire interface TX_FAULT (A2h, byte 110, bit 2) asserted. 11.Time for two-wire interface assertion of Rx_LOS (A2h, byte 110, bit 1) from loss of optical signal. 12.Time for two-wire interface de-assertion of Rx_LOS (A2h, byte 110, bit 1) from presence of valid optical signal. 13.From power on to data ready bit asserted (A2h, byte 110, bit 0). Data ready indicates analog monitoring circuitry is functional. 14.Time from power on until module is ready for data transmission over the serial bus (reads or writes over A0h and A2h). 15.Time from stop bit to completion of a 1-8 byte write command. 13

Table 9. Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics Parameter Symbol Min. Units Notes Transceiver Internal Temperature T ±3.0 ˚C Temperature is measured internal to the transceiver. INT Accuracy Valid from = -40˚C to 85˚C case temperature. Transceiver Internal Supply V ±0.1 V Supply voltage is measured internal to the transceiver INT Voltage Accuracy and can, with less accuracy, be correlated to voltage at the SFP Vcc pin. Valid over 3.3 V ±5%. Transmitter Laser DC Bias Current I ±10 % I is better than ±10% of the nominal value. INT INT Accuracy Transmitted Average Optical P ±3.0 dB Coupled into 50/125 µm multi-mode fiber. T Output Power Accuracy Valid from100 µW to 500 µW, avg. Received Average Optical Input P ±3.0 dB Coupled from 50/125 µm multi-mode fiber. R Power Accuracy Valid from 31 µW to 500 µW, avg. VCC > 3.15 V VCC > 3.15 V TX_FAULT TX_FAULT TX_DISABLE TX_DISABLE TRANSMITTED SIGNAL TRANSMITTED SIGNAL t_init t_init t-init: TX DISABLE NEGATED t-init: TX DISABLE ASSERTED VCC > 3.15 V TX_FAULT TX_FAULT TX_DISABLE TX_DISABLE TRANSMITTED SIGNAL TRANSMITTED SIGNAL t_off t_on t_init INSERTION t-init: TX DISABLE NEGATED, MODULE HOT PLUGGED t-off & t-on: TX DISABLE ASSERTED THEN NEGATED OCCURANCE OF FAULT OCCURANCE OF FAULT TX_FAULT TX_FAULT TX_DISABLE TX_DISABLE TRANSMITTED SIGNAL TRANSMITTED SIGNAL t_fault * SFP SHALL CLEAR TX_FAULT IN t_reset t_init* t_init IF THE FAILURE IS TRANSIENT t-fault: TX FAULT ASSERTED, TX SIGNAL NOT RECOVERED t-reset: TX DISABLE ASSERTED THEN NEGATED, TX SIGNAL RECOVERED OCCURANCE OF FAULT OPTICAL SIGNAL TX_FAULT OCCURANCE OF LOSS TX_DISABLE TRANSMITTED SIGNAL LOS t_fault2 t_reset t_loss_on t_loss_off * SFP SHALL CLEAR Tx_FAULT IN t_init* t_init IF THE FAILURE IS TRANSIENT t-fault2: TX DISABLE ASSERTED THEN NEGATED, t-loss-on & t-loss-off TX SIGNAL NOT RECOVERED NOTE: t_fault2 timing is typically 1.7 to 2 ms. Figure 6. Transceiver timing diagrams (Module installed except where noted). 14

Table 10. EEPROM Serial ID Memory Contents, Page A0h Byte # Data Byte # Data Decimal Hex Notes Decimal Hex Notes 0 03 SFP physical device 37 00 Vendor OUI (Note 4) 1 04 SFP function defined by serial ID only 38 17 Vendor OUI (Note 4) 2 07 LC optical connector 39 6A Vendor OUI (Note 4) 3 00 40 41 "A" - Vendor Part Number ASCII character 4 00 41 46 "F" - Vendor Part Number ASCII character 5 00 42 42 "B" - Vendor Part Number ASCII character 6 01 1000BaseSX 43 52 "R" - Vendor Part Number ASCII character 7 20 Intermediate distance (per FC-PI) 44 2D "-" - Vendor Part Number ASCII character 8 40 Shortwave laser without OFC (open fiber control) 45 35 "5" - Vendor Part Number ASCII character 9 0C Multi-mode 50 m and 62.5 m optical media 46 37 "7" - Vendor Part Number ASCII character 10 01 100 Mbytes/sec FC-PI speed[1] 47 30 "0" - Vendor Part Number ASCII character 11 01 Compatible with 8B/10B encoded data 48 Note 5 12 0C 1200Mbps nominal bit rate (1.25Gbps) 49 Note 5 13 00 50 Note 5 14 00 51 Note 5 15 00 52 20 " " - Vendor Part Number ASCII character 16 37 550m of 50/125µm fiber @ 1.25Gbps (Note 2) 53 20 " " - Vendor Part Number ASCII character 17 1B 275m of 62.5/125µm fiber @ 1.25Gbps (Note 3 54 20 " " - Vendor Part Number ASCII character 18 00 55 20 " " - Vendor Part Number ASCII character 19 00 56 20 " " - Vendor Revision Number ASCII character 20 41 'A' - Vendor Name ASCII character 57 20 " " - Vendor Revision Number ASCII character 21 56 "V" - Vendor Name ASCII character 58 20 " " - Vendor Revision Number ASCII character 22 41 "A" - Vendor Name ASCII character 59 20 " " - Vendor Revision Number ASCII character 23 47 "G"- Vendor Name ASCII character 60 03 Hex Byte of Laser Wavelength (Note 6) 24 4F "O" - Vendor Name ASCII character 61 52 Hex Byte of Laser Wavelength (Note 6) 25 20 " " - Vendor Name ASCII character 62 00 26 20 " " - Vendor Name ASCII character 63 Checksum for bytes 0-62 (Note 7) 27 20 " " - Vendor Name ASCII character 64 00 28 20 " " - Vendor Name ASCII character 65 1A Hardware SFP TX_DISABLE, TX_FAULT, & RX_LOS 29 20 " " - Vendor Name ASCII character 66 00 30 20 " " - Vendor Name ASCII character 67 00 31 20 " " - Vendor Name ASCII character 68-83 Vendor Serial Number, ASCII (Note 8) 32 20 " " - Vendor Name ASCII character 84-91 Vendor Date Code, ASCII (Note 9) 33 20 " " - Vendor Name ASCII character 92 Note 5 34 20 " " - Vendor Name ASCII character 93 Note 5 35 20 " " - Vendor Name ASCII character 94 Note 5 36 00 95 Checksum for bytes 64-94 (Note 7) 96 - 255 00 Notes: 1. FC-PI speed 100 MBytes/sec is a serial bit rate of 1.0625 GBit/sec. 2. Link distance with 50/125µm cable at 1.25Gbps is 550m. 3. Link distance with 62.5/125µm cable at 1.25Gbps is 275m. 4. The IEEE Organizationally Unique Identifier (OUI) assigned to Avago Technologies is 00-17-6A (3 bytes of hex). 5. See Table 11 for part number extensions and data-fields. 6. Laser wavelength is represented in 16 unsigned bits. The hex representation of 850nm is 0352. 7. Addresses 63 and 95 are checksums calculated per SFF-8472 and SFF-8074, and stored prior to product shipment. 8. Addresses 68-83 specify the module’s ASCII serial number and will vary by unit. 9. Addresses 84-91 specify the module’s ASCII date code and will vary according to manufactured date-code. 15

Table 11. Part Number Extensions AFBR-5701ALZ AFBR-5701APZ AFBR-5701LZ AFBR-5701PZ Address Hex ASCII Address Hex ASCII Address Hex ASCII Address Hex ASCII 48 31 1 48 31 1 48 31 1 48 31 1 49 41 A 49 41 A 49 4C L 49 50 P 50 4C L 50 50 P 50 5A Z 50 5A Z 51 5A Z 51 5A Z 51 20 51 20 92 00 92 00 92 00 92 00 93 00 93 00 93 00 93 00 94 00 94 00 94 00 94 00 AFBR-5705ALZ AFBR-5705APZ AFBR-5705LZ AFBR-5705PZ Address Hex ASCII Address Hex ASCII Address Hex ASCII Address Hex ASCII 48 35 5 48 35 5 48 35 5 48 35 5 49 41 A 49 41 A 49 4C L 49 50 P 50 4C L 50 50 P 50 5A Z 50 5A Z 51 5A Z 51 5A Z 51 20 51 20 92 68 92 68 92 68 92 68 93 F0 93 F0 93 F0 93 F0 94 01 94 01 94 01 94 01 16

Table 12. EEPROM Serial ID Memory Contents - Address A2h (AFBR-5705Z family only) Byte # Notes Byte # Notes Byte # Notes Decimal Decimal Decimal 0 Temp H Alarm MSB1 26 Tx Pwr L Alarm MSB4 104 Real Time Rx P MSB5 AV 1 Temp H Alarm LSB1 27 Tx Pwr L Alarm LSB4 105 Real Time Rx P LSB5 AV 2 Temp L Alarm MSB1 28 Tx Pwr H Warning MSB4 106 Reserved 3 Temp L Alarm LSB1 29 Tx Pwr H Warning LSB4 107 Reserved 4 Temp H Warning MSB1 30 Tx Pwr L Warning MSB4 108 Reserved 5 Temp H Warning LSB1 31 Tx Pwr L Warning LSB4 109 Reserved 6 Temp L Warning MSB1 32 Rx Pwr H Alarm MSB5 110 Status/Control - see Table 13 7 Temp L Warning LSB1 33 Rx Pwr H Alarm LSB5 111 Reserved 8 V H Alarm MSB2 34 Rx Pwr L Alarm MSB5 112 Flag Bits - see Table 14 CC 9 V H Alarm LSB2 35 Rx Pwr L Alarm LSB5 113 Flag Bit - see Table 14 CC 10 V L Alarm MSB2 36 Rx Pwr H Warning MSB5 114 Reserved CC 11 V L Alarm LSB2 37 Rx Pwr H Warning LSB5 115 Reserved CC 12 V H Warning MSB2 38 Rx Pwr L Warning MSB5 116 Flag Bits - see Table 14 CC 13 V H Warning LSB2 39 Rx Pwr L Warning LSB5 117 Flag Bits - see Table 14 CC 14 V L Warning MSB2 40-55 Reserved 118 Reserved CC 15 V L Warning LSB2 56-94 External Calibration Constants6 119 Reserved CC 16 Tx Bias H Alarm MSB3 95 Checksum for Bytes 0-947 120-122 Reserved 17 Tx Bias H Alarm LSB3 96 Real Time Temperature MSB1 123 18 Tx Bias L Alarm MSB3 97 Real Time Temperature LSB1 124 19 Tx Bias L Alarm LSB3 98 Real Time Vcc MSB2 125 20 Tx Bias H Warning MSB3 99 Real Time Vcc LSB2 126 21 Tx Bias H Warning LSB3 100 Real Time Tx Bias MSB3 127 Reserved8 22 Tx Bias L Warning MSB3 101 Real Time Tx Bias LSB3 128-247 Customer Writable9 23 Tx Bias L Warning LSB3 102 Real Time Tx Power MSB4 248-255 Vendor Specific 24 Tx Pwr H Alarm MSB4 103 Real Time Tx Power LSB4 25 Tx Pwr H Alarm LSB4 Notes: 1. Temperature (Temp) is decoded as a 16 bit signed twos compliment integer in increments of 1/256 °C. 2. Supply voltage (VCC) is decoded as a 16 bit unsigned integer in increments of 100 µV. 3. Laser bias current (Tx Bias) is decoded as a 16 bit unsigned integer in increments of 2 µA. 4. Transmitted average optical power (Tx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 µW. 5. Received average optical power (Rx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 µW. 6. Bytes 55-94 are not intended from use with AFBR-5705Z, but have been set to default values per SFF-8472. 7. Bytes 95 is a checksum calculated (per SFF-8472) and stored prior to product shipment. 8. Byte 127 accepts a write but performs no action (reserved legacy byte). 9. Bytes 128-247 are write enabled (customer writable). 17

Table 13. EEPROM Serial ID Memory Contents - Address A2h, Byte 110 (AFBR-5705Z family only) Bit # Status/Control Name Description 7 Tx Disable State Digital state of SFP Tx Disable Input Pin (1 = Tx_ Disable asserted) 6 Soft Tx Disable Read/write bit for changing digital state of SFP Tx_Disable function1 5 Reserved 4 Rx Rate Select State Digital state of SFP Rate Select Input Pin (1 = full bandwidth of 155 Mbit)2 3 Reserved 2 Tx Fault State Digital state of the SFP Tx Fault Output Pin (1 = Tx Fault asserted) 1 Rx LOS State Digital state of the SFP LOS Output Pin (1 = LOS asserted) 0 Data Ready (Bar) Indicates transceiver is powered and real time sense data is ready (0 = Ready) Notes: 1. Bit 6 is logic OR’d with the SFP Tx_Disable input pin 3 ... either asserted will disable the SFP transmitter. 2. AFBR-5705Z does not respond to state changes on Rate Select Input Pin. It is internally hardwired to full bandwidth. Table 14. EEPROM Serial ID Memory Contents - Address A2h, Bytes 112, 113, 116, 117 (AFBR-5705Z family only) Byte Bit # Flag Bit Name Description 112 7 Temp High Alarm Set when transceiver nternal temperature exceeds high alarm threshold. 6 Temp Low Alarm Set when transceiver internal temperature exceeds alarm threshold. 5 V High Alarm Set when transceiver internal supply voltage exceeds high alarm threshold. CC 4 V Low Alarm Set when transceiver internal supply voltage exceeds low alarm threshold. CC 3 Tx Bias High Alarm Set when transceiver laser bias current exceeds high alarm threshold. 2 Tx Bias Low Alarm Set when transceiver laser bias current exceeds low alarm threshold. 1 Tx Power High Alarm Set when transmitted average optical power exceeds high alarm threshold. 0 Tx Power Low Alarm Set when transmitted average optical power exceeds low alarm threshold. 113 7 Rx Power High Alarm Set when received P_Avg optical power exceeds high alarm threshold. 6 Rx Power Low Alarm Set when received P_Avg optical power exceeds low alarm threshold. 0-5 Reserved 116 7 Temp High Warning Set when transceiver internal temperature exceeds high warning threshold. 6 Temp Low Warning Set when transceiver internal temperature exceeds low warning threshold. 5 V High Warning Set when transceiver internal supply voltage exceeds high warning threshold. CC 4 V Low Warning Set when transceiver internal supply voltage exceeds low warning threshold. CC 3 Tx Bias High Warning Set when transceiver laser bias current exceeds high warning threshold. 2 Tx Bias Low Warning Set when transceiver laser bias current exceeds low warning threshold. 1 Tx Power High Warning Set when transmitted average optical power exceeds high warning threshold. 0 Tx Power Low Warning Set when transmitted average optical power exceeds low warning threshold. 117 7 Rx Power High Warning Set when received P_Avg optical power exceeds high warning threshold. 9 Rx Power Low Warning Set when received P_Avg optical power exceeds low warning threshold. 0-5 Reserved 18

AVAGO AFBR-570xZ 850 nm LASER PROD 21CFR(J) CLASS 1 COUNTRY OF ORIGIN YYWW TUV XXXXXX UL 13.8±0.1 13.4±0.1 [0.541±0.004] [0.528±0.004] DEVICE SHOWN WITH DUST CAP AND BAIL 2.60 WIRE DELATCH [0.10] 55.2±0.2 [2.17±0.01] FRONT EDGE OF SFP TRANSCEIVER CAGE 6.25±0.05 0.7 MAX. UNCOMPRESSED [0.246±0.002] [0.028] 13.0±0.2 8.5±0.1 [0.512±0.008] [0.335±0.004] TX RX AREA FOR PROCESS PLUG 6.6 [0.261] 13.50 [0.53] 14.8 MAX. UNCOMPRESSED [0.583] STANDARD DELATCH 12.1±0.2 [0.48±0.01] DIMENSIONS ARE IN MILLIMETERS (INCHES) Figure 7. Module drawing 19

X Y 34.5 3x 10 7.2 7.1 10x 1.05 ± 0.01 16.25 Æ 0.1 S X A S 2.5 Æ 0.85 ± 0.05 MIN .PITCH B 1 2.5 Æ 0.1 S X Y PCB A 1 EDGE 3.68 5.68 PIN 1 20 8.58 2x 1.7 8.48 11.08 11.93 16.2514.25 9.6 REF. 4.8 11 10 SEE DETAIL 1 11x 2.0 9x 0.95 ± 0.05 11x 2.0 Æ 0.1 L X A S 26.8 5 2 3 3x 10 41.3 42.3 5 20x 0.5 ± 0.03 3.2 0.9 0.06 S A S B S PIN 1 20 10.93 10.53 11.93 NOTES 9.6 0.8 1. PADS AND VIAS ARE CHASSIS GROUND TYP. 2. THROUGH HOLES, PLATING OPTIONAL. 11 10 3. HATCHED AREA DENOTES COMPONENT AND TRACE KEEPOUT (EXCEPT CHASSIS GROUND). 4. AREA DENOTES COMPONENT KEEPOUT 4 (TRACES ALLOWED). 2 ± 0.05 TYP. 2x 1.55 ± 0.05 0.06 L A S B S DIMENSIONS IN MILLIMETERS Æ 0.1 L A S B S DETAIL 1 Figure 8. SFP host board mechanical layout 20

1.7 ± 0.9 (0.07 ± 0.04) 3.5 ± 0.3 (0.14 ± 0.01) 41.73 ± 0.5 PCB (1.64 ± 0.02) BEZEL AREA 15 MAX. FOR (0.59) PROCESS PLUG CAGE ASSEMBLY 15.25 ± 0.1 (0.60 ± 0.004) 11 REF. (0.43) 9.8 10.4 ± 0.1 MAX. (0.39) (0.41 ± 0.004) 10 REF 1.5 REF. (0.39) (0.06) TO PCB 16.25 ± 0.1 MIN. PITCH BELOW PCB (0.64 ± 0.004) 0.4 ± 0.1 (0.02 ± 0.004) MSA-SPECIFIED BEZEL BELOW PCB DIMENSIONS ARE IN MILLIMETERS (INCHES). Figure 9. Assembly drawing. 21

Ordering Information Please contact your local field sales engineer or one of Avago Technologies franchised distributors for ordering information. For technical information, please visit Avago Technologies’ web-page at www.avagotech.com or contact one of Avago Technologies’ regional Technical Response Centers. For information related to SFF Committee documentation visit www.sffcommittee.org. AFBR-5705LZ DMI Extended Temperature (-10°C to 85°C) Standard Delatch AFBR-5705PZ DMI Extended Temperature (-10°C to 85°C) Bail Delatch AFBR-5705ALZ DMI Industrial Temperature (-40°C to 85°C) Standard Delatch AFBR-5705APZ DMI Industrial Temperature (-40°C to 85°C) Bail Delatch AFBR-5701LZ No DMI Extended Temperature (-10°C to 85°C) Standard Delatch AFBR-5701PZ No DMI Extended Temperature (-10°C to 85°C) Bail Delatch AFBR-5701ALZ No DMI Industrial Temperature (-40°C to 85°C) Standard Delatch AFBR-5701APZ No DMI Industrial Temperature (-40°C to 85°C) Bail Delatch For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Pte. in the United States and other countries. Data subject to change. Copyright © 2006 Avago Technologies Pte. All rights reserved. AV01-0093EN - May 7, 2006 22