Microprocessor Supervisory Circuits in 3-Lead SC70 and SOT-23 Data Sheet ADM803/ADM809/ADM810 FEATURES FUNCTIONAL BLOCK DIAGRAMS Specified over temperature Low power consumption: 17 μA ADM803 Precision voltage monitor: 2.5 V, 3 V, 3.3 V, 5 V options VCC RESET Reset assertion down to 1 V VCC GENERATOR RESET 140 ms minimum power-on reset VREF 240ms Open-drain RESET output (ADM803) Push-pull RESET output (ADM809) GND Push-pull RESET output (ADM810) SC70 and SOT-23 packages ADM809/ADM810 APPLICATIONS Microprocessor systems VCC GENREERSAETTOR RESET Computers VREF 240ms (RESET) Controllers Intelligent instruments GND VCC VCC *RPULL-UP VCC MICROPROCESSOR ADM803/ADM809 SYSTEM RESET RESET INPUT GND GND *ADM803 ONLY 03736-001 Figure 1. GENERAL DESCRIPTION The ADM803/ADM809/ADM810 supervisory circuits monitor Seven reset threshold voltage options are available, suitable for the power supply voltage in microprocessor systems. They monitoring a variety of supply voltages (see Table 3). provide a reset output during power-up, power-down, and The reset comparator features built-in glitch immunity, making brownout conditions. On power-up, an internal timer holds it immune to fast transients on V . CC reset asserted for 240 ms. This holds the microprocessor in a The ADM803/ADM809/ADM810 consume only 17 μA, making reset state until conditions have stabilized. The reset output them suitable for low power, portable equipment. The ADM803 remains operational with V as low as 1 V. The ADM803 and CC is available in a 3-lead SC70; the ADM809/ADM810 are available ADM809 provide an active low reset signal (RESET), whereas in 3-lead SOT-23 and 3-lead SC70 packages. the ADM810 provides an active high signal (RESET) output. The ADM809 and ADM810 have push-pull outputs, whereas the ADM803 has an open-drain output, which requires an external pull-up resistor. Rev. I Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Tel: 781.329.4700 ©1997–2014 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. Technical Support www.analog.com

ADM803/ADM809/ADM810 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Pin Configurations and Function Descriptions ............................5 Applications ....................................................................................... 1 Typical Performance Characteristics ..............................................6 Functional Block Diagrams ............................................................. 1 Interfacing to Other Devices ............................................................8 General Description ......................................................................... 1 Ensuring a Valid Reset Output Down to V = 0 V .................8 CC Revision History ............................................................................... 2 Benefits of an Accurate Reset Threshold ...................................8 Specifications ..................................................................................... 3 Interfacing to Microprocessors with Multiple Interrupts ........8 Absolute Maximum Ratings ............................................................ 4 Outline Dimensions ..........................................................................9 ESD Caution .................................................................................. 4 Ordering Guide .......................................................................... 10 REVISION HISTORY 10/14—Rev. H to Rev. I 5/03—Rev. B to Rev. C. Changes to Applications Section .................................................... 1 Added ADM803 ................................................................. Universal Changes to Table 2 ............................................................................ 4 Changes to Features .......................................................................... 1 Updated Outline Dimensions ......................................................... 9 Changes to General Description ..................................................... 1 Changes to Ordering Guide .......................................................... 10 Changes to Figure 1 ........................................................................... 1 Changes to Specifications ................................................................. 2 8/08—Rev. G to Rev. H Changes to Table I ............................................................................. 3 Added Figure 4; Renumbered Sequentially .................................. 5 Updated Ordering Guide ................................................................. 4 Changes to Figure 8 .......................................................................... 6 Updated Outline Dimensions ......................................................... 9 1/03—Rev. A to Rev. B. Changes to Ordering Guide .......................................................... 10 Changes to Specifications ................................................................. 2 Changes to Table I ............................................................................. 3 9/06—Rev. F to Rev. G Changes to Ordering Guide ............................................................. 4 Updated Outline Dimensions ......................................................... 9 Changes to TPCs 1–3, and TPC 7 ................................................... 5 Changes to Ordering Guide ............................................................ 9 Updated Outline Dimensions .......................................................... 7 6/05—Rev. E to Rev. F. 10/02—Rev. 0 to Rev. A. Changes to Ordering Guide ............................................................ 4 Addition of SC70 package ................................................. Universal Updated Outline Dimensions ......................................................... 9 Change to General Description ....................................................... 1 Changes to Specifications ................................................................. 2 2/05—Rev. D to Rev. E. Changes to Absolute Maximum Ratings ........................................ 3 Changes to Ordering Guide ............................................................ 4 Change to Table I ............................................................................... 3 Change to Ordering Guide ............................................................... 4 2/05—Rev. C to Rev. D. Change to TPC 1 ............................................................................... 5 Changes to Ordering Guide ............................................................ 4 Updated Outline Dimensions .......................................................... 7 Updated Outline Dimensions ......................................................... 8 4/97—Revision 0: Initial Version Rev. I | Page 2 of 11

Data Sheet ADM803/ADM809/ADM810 SPECIFICATIONS V = full operating range, T = T to T , V typical = 5 V for L/M/J models, 3.3 V for T/S models, 3 V for R models, and 2.5 V for CC A MIN MAX CC Z models, unless otherwise noted. Table 1. Parameter Min Typ Max Unit Test Conditions/Comments V OPERATING VOLTAGE RANGE 1.0 5.5 V T = 0°C to 70°C CC A 1.2 5.5 V T = −40°C to +125°C A Supply Current 24 35 μA V < 5.5 V, ADM8xxL/M/J, T = −40°C to +85°C CC A 17 30 μA V < 3.6 V, ADM8xxR/S/T/Z, T = −40°C to +85°C CC A 60 μA V < 5.5 V, ADM8xxL/M/J, T = 85°C to 125°C CC A 60 μA V < 3.6 V, ADM8xxR/S/T/Z, T = 85°C to 125° C CC A RESET VOLTAGE THRESHOLD ADM8xxL 4.56 4.63 4.70 V T = 25°C A 4.50 4.75 V T = −40°C to +85°C A 4.44 4.82 V T = −40°C to +125°C A ADM8xxM 4.31 4.38 4.45 V T = 25°C A 4.25 4.50 V T = −40°C to +85°C A 4.20 4.56 V T = −40°C to +125°C A ADM8xxJ 3.93 4.00 4.06 V T = 25°C (ADM809/ADM810 only) A 3.89 4.10 V T = −40°C to +85°C (ADM809/ADM810 only) A 3.80 4.20 V T = −40°C to +125°C (ADM809/ADM810 only) A ADM8xxT 3.04 3.08 3.11 V T = 25°C A 3.00 3.15 V T = −40°C to +85°C A 2.95 3.21 V T = −40°C to +125°C A ADM8xxS 2.89 2.93 2.96 V T = 25°C A 2.85 3.00 V T = −40°C to +85°C A 2.81 3.05 V T = −40°C to +125°C A ADM8xxR 2.59 2.63 2.66 V T = 25°C A 2.55 2.70 V T = −40°C to +85°C A 2.52 2.74 V T = −40°C to +125°C A ADM8xxZ 2.28 2.32 2.35 V T = 25°C A 2.25 2.38 V T = −40°C to +85°C A 2.22 2.42 V T = −40°C to +125°C A RESET THRESHOLD TEMPERATURE COEFFICIENT 30 ppm/°C V to Reset Delay 20 μs V = V to (V − 100 mV) CC CC TH TH RESET ACTIVE TIMEOUT PERIOD 140 240 460 ms T = −40°C to +85°C A 100 840 ms T = 85°C to 125°C A RESET OUTPUT VOLTAGE LOW (ADM803/ADM809) 0.3 V V = V min, I = 1.2 mA, ADM803R/S/T/Z, CC TH SINK ADM809R/S/T/Z 0.4 V V = V min, I = 3.2 mA, ADM803L/M/J, CC TH SINK ADM809L/M/J 0.3 V V > 1.0 V, I = 50 μA CC SINK RESET OUTPUT VOLTAGE HIGH (ADM809) 0.8 V V V > V max, I = 500 μA, ADM809R/S/T/Z CC CC TH SOURCE V − 1.5 V V > V max, I = 800 μA, ADM809L/M/J CC CC TH SOURCE RESET OUTPUT VOLTAGE LOW (ADM810) 0.3 V V = V min, I = 1.2 mA, ADM810R/S/T/Z CC TH SINK 0.4 V V = V min, I = 3.2 mA, ADM810L/M/J CC TH SINK RESET OUTPUT VOLTAGE HIGH (ADM810) 0.8 V V 1.8 V < V < V min, I = 150 μA CC CC TH SOURCE RESET OPEN-DRAIN OUTPUT Leakage Current (ADM803) 1 μA V > V , RESET deasserted CC TH Rev. I | Page 3 of 11

ADM803/ADM809/ADM810 Data Sheet ABSOLUTE MAXIMUM RATINGS T = 25°C, unless otherwise noted. A Table 3. Reset Threshold Options RESET Model Threshold (V) Table 2. ADM8xxL 4.63 Parameter Ratings ADM8xxM 4.38 V −0.3 V to +6 V CC ADM8xxJ (ADM809/ADM810 Only) 4.00 RESET, RESET (Push-Pull) −0.3 V to VCC + 0.5 V ADM8xxT 3.08 RESET (Open-Drain) −0.3 V to +6.0 V ADM8xxS 2.93 Input Current ADM8xxR 2.63 V 20 mA CC ADM8xxZ 2.32 Output Current RESET, RESET 20 mA Rate of Rise, V 100 V/μs CC θJA Thermal Impedance VCC VREF VREF VREF VREF SC70 146°C/W SOT-23 270°C/W RESET t1 t1 Lead Temperature (Soldering, 10 sec) 300°C VInafpraorre Pdh (a1s5e s (e6c0) sec) 221250°°CC tV1R=E FR =E SREETS ETTIM VEO =L T24A0GmEs TTHYRPESHOLD 03736-003 Storage Temperature Range −65°C to +150°C Figure 2. Power Fail Reset Timing ESD CAUTION Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. Rev. I | Page 4 of 11

Data Sheet ADM803/ADM809/ADM810 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS GND 1 ADM803/ GND 1 ADM809/ ADM810 TOP VIEW 3 VCC TOP VIEW 3 VCC RESET 2 (Not to Scale) 03736-002 RESET 2 (Not to Scale) 03736-102 Figure 3. ADM803/ADM809 Pin Configuration Figure 4. ADM810 Pin Configuration Table 4. Pin Function Descriptions Pin No. ADM803/ADM809 ADM810 Mnemonic Description 1 1 GND Ground Reference for All Signals; 0 V. N/A 2 RESET Active High Logic Output. RESET remains high while V is below the reset threshold CC and remains high for 240 ms (typical) after V rises above the reset threshold. CC 2 N/A RESET Active Low Logic Output. RESET remains low while VCC is below the reset threshold and remains low for 240 ms (typical) after V rises above the reset threshold. CC 3 3 V Supply Voltage Being Monitored. CC Rev. I | Page 5 of 11

ADM803/ADM809/ADM810 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS 30 240.0 VCC = 5V 239.5 25 ms) 239.0 A) UT ( 238.5 NT (µ 20 VCC = 3V MEO 238.0 E TI CURR 15 ESET 237.5 UPPLY 10 R-UP R 223367..50 S E W O 236.0 5 P 235.5 0–40 –20 0TEMPER2A0TURE (°4C0) 60 8085 03736-004 235.0–40 –20 0TEMPER20ATURE (°4C0) 60 8085 03736-007 Figure 5. Supply Current vs. Temperature (No Load) Figure 8. Power-Up Reset Timeout vs. Temperature, ADM8xxR 200 1.0020 VOD = VTH – VCC 180 VOD = 10mV D1.0015 s)160 HOL WN RESET (µ111420000 VOD = 20mV ESET THRES11..00001005 O R POWER-D 8600 RMALIZED 1.0000 40 VOD = 100mV NO0.9995 20 VOD = 200mV 0–40 –20 0TEMPER20ATURE (°4C0) 60 8085 03736-005 0.9990–40 –20 0TEMPER20ATURE (°4C0) 60 8085 03736-008 Figure 6. Power-Down Reset Delay vs. Temperature, ADM8xxL/M/J Figure 9. Normalized Reset Voltage Threshold vs. Temperature 180 VOD = VTH – VCC 160 SUPPLYVOLTAGE VOD = 10mV 5V p-p s)140 µ ET (120 T S E WN R100 VOD = 20mV 1 RVOESLTEATGOEUTPUT DO 80 R- ADM809T WE 60 ADM809R O P 40 VOD = 100mV 2 T 20 0–40 –20 0TEVMOPDE R2=0 A2T00UmREV (°4C0) 60 8085 03736-006 CH1 2.00V CH2 2.00V M 200ms CH1 2.00V 03736-009 Figure 7. Power-Down Reset Delay vs. Temperature, ADM8xxT/S/R/Z Figure 10. Reset Output Voltage vs. Supply Voltage Rev. I | Page 6 of 11

Data Sheet ADM803/ADM809/ADM810 400 s)350 µ N ( O300 TI RA U250 D T N E200 NSI A R150 M T ADM8xxL/M/J U XIM100 A ADM8xxR/S/T/Z M 50 01 RESET COMPA1R0ATOR OVERDRIVE1,0 V0TH–VCC(mV) 1000 03736-010 Figure 11. Maximum Transient Duration Without Causing a Reset Pulse vs. Reset Comparator Overdrive Rev. I | Page 7 of 11

ADM803/ADM809/ADM810 Data Sheet INTERFACING TO OTHER DEVICES The ADM803/ADM809/ADM810 series is designed to integrate ADM803/ADM809/ADM810, the possibility of a malfunction with as many devices as possible and, therefore, has a standard during a power failure is greatly reduced because the devices output dependent on V . This enables the parts to be used in can operate effectively even when there are large degradations CC both 3 V and 5 V, or any nominal voltage within the minimum of the supply voltages. Another advantage is the very accurate and maximum specifications for V . This design simplifies internal voltage reference circuit of the ADM803/ADM809/ CC interfacing the ADM803/ADM809/ADM810 to other devices. ADM810. These benefits combine to produce an exceptionally reliable voltage monitor circuit. ENSURING A VALID RESET OUTPUT DOWN TO V = 0 V INTERFACING TO MICROPROCESSORS WITH CC MULTIPLE INTERRUPTS When V falls below 0.8 V, the ADM803/ADM809 RESET no CC longer sinks current. A high impedance CMOS logic input In a number of cases, it is necessary to interface many interrupts connected to RESET may, therefore, drift to undetermined logic from different devices (for example, thermal, altitude, and levels. To eliminate this problem, a 100 kΩ resistor should be velocity sensors). The ADM803/ADM809/ADM810 can easily connected from RESET to ground. be integrated into existing interrupt-handling circuits, as shown in Figure 13, or can be used as standalone devices. VCC VCC PRIORITY ENCODER 4-LINE BCDTO 74LS147 MICROPROCESSOR ADM809 VCC RESET VCC ADM809 GND 03736-011 RESET OTHDEERV SICEENSSING Figure 12. Ensuring a Valid Reset Output Down to VCC = 0 V GND BENEFITS OF AN ACCURATE RESET THRESHOLD In other microprocessors, tolerances in supply voltages lead 03736-012 Figure 13. Interfacing to Microprocessors with Multiple Interrupts to an overall increase in reset tolerance levels due to the deterioration of the reset circuit’s power supply. In the Rev. I | Page 8 of 11

Data Sheet ADM803/ADM809/ADM810 OUTLINE DIMENSIONS 3.04 2.90 2.80 1.40 1.30 1.20 3 2.64 2.10 1 2 0.60 1.03 0.45 0.89 2.05 1.78 1.02 0.95 0.54 REF 0.88 1.12 GAUGE PLANE 0.89 0.100 0.180 0.013 0.085 0.51 SEPALTAINNGE 0.37 0.25 0.60 MAX 0.30 MIN C COMPLIANTTO JEDEC STANDARDSTO-236-AB 011909- Figure 14. 3-Lead Small Outline Transistor Package [SOT-23-3] (RT-3) Dimensions shown in millimeters 2.20 2.00 1.80 1.35 1.25 1.15 3 2.40 2.10 1 2 1.80 0.65BSC 1.00 1.10 0.40 0.80 0.80 0.10 0.30 0.10MAX 0.40 SEATING 00..2160 0.20 0.25 PLANE COPLANARITY 0.10 0.10 A ALLDIMENSIONSCOMPLIANTWITHEIAJSC70 072809- Figure 15. 3-Lead Thin Shrink Small Outline Transistor Package [SC70] (KS-3) Dimensions shown in millimeters Rev. I | Page 9 of 11

ADM803/ADM809/ADM810 Data Sheet ORDERING GUIDE Package Package Model1 Reset Threshold (V) Temperature Range Branding2, 3 Quantity Description Option ADM803LAKSZ-REEL 4.63 −40°C to +125°C M6L 10,000 3-Lead SC70 KS-3 ADM803LAKSZ-REEL7 4.63 −40°C to +125°C M6L 3,000 3-Lead SC70 KS-3 ADM803MAKS-REEL7 4.38 −40°C to +125°C M03 3,000 3-Lead SC70 KS-3 ADM803MAKSZ-REEL7 4.38 −40°C to +125°C M6J 3,000 3-Lead SC70 KS-3 ADM803RAKSZ-REEL7 2.63 −40°C to +125°C M6M 3,000 3-Lead SC70 KS-3 ADM803SAKS-REEL7 2.93 −40°C to +125°C M06 3,000 3-Lead SC70 KS-3 ADM803SAKSZ-REEL 2.93 −40°C to +125°C M50 10,000 3-Lead SC70 KS-3 ADM803SAKSZ-REEL7 2.93 −40°C to +125°C M50 3,000 3-Lead SC70 KS-3 ADM803TAKS-REEL7 3.08 −40°C to +125°C M05 3,000 3-Lead SC70 KS-3 ADM803TAKSZ-REEL7 3.08 −40°C to +125°C M4M 3,000 3-Lead SC70 KS-3 ADM803ZAKSZ-REEL7 2.32 −40°C to +125°C M6N 3,000 3-Lead SC70 KS-3 ADM809JAKS-REEL7 4.00 −40°C to +125°C M9C or 9JXX 3,000 3-Lead SC70 KS-3 ADM809JAKSZ-REEL 4.00 −40°C to +125°C M6P 10,000 3-Lead SC70 KS-3 ADM809JAKSZ-REEL7 4.00 −40°C to +125°C M6P 3,000 3-Lead SC70 KS-3 ADM809JARTZ-REEL7 4.00 −40°C to +125°C M6P 3,000 3-Lead SOT-23 RT-3 ADM809LAKS-REEL7 4.63 −40°C to +125°C M9A 3,000 3-Lead SC70 KS-3 ADM809LAKSZ-REEL 4.63 −40°C to +125°C M6R 10,000 3-Lead SC70 KS-3 ADM809LAKSZ-REEL7 4.63 −40°C to +125°C M6R 3,000 3-Lead SC70 KS-3 ADM809LART-REEL7 4.63 −40°C to +125°C 9LXX 3,000 3-Lead SOT-23 RT-3 ADM809LARTZ-REEL 4.63 −40°C to +125°C 9LXX 10,000 3-Lead SOT-23 RT-3 ADM809LARTZ-REEL7 4.63 −40°C to +125°C 9LXX 3,000 3-Lead SOT-23 RT-3 ADM809MAKS-REEL7 4.38 −40°C to +125°C M9B 3,000 3-Lead SC70 KS-3 ADM809MAKSZ-REEL 4.38 −40°C to +125°C M51 10,000 3-Lead SC70 KS-3 ADM809MAKSZ-REEL7 4.38 −40°C to +125°C M51 3,000 3-Lead SC70 KS-3 ADM809MART-REEL7 4.38 −40°C to +125°C 9MXX 3,000 3-Lead SOT-23 RT-3 ADM809MARTZ-REEL 4.38 −40°C to +125°C M51 10,000 3-Lead SOT-23 RT-3 ADM809MARTZ-REEL7 4.38 −40°C to +125°C M51 3,000 3-Lead SOT-23 RT-3 ADM809RAKS-REEL 2.63 −40°C to +125°C M9F 10,000 3-Lead SC70 KS-3 ADM809RAKS-REEL7 2.63 −40°C to +125°C M9F 3,000 3-Lead SC70 KS-3 ADM809RAKSZ-REEL 2.63 −40°C to +125°C M4D 10,000 3-Lead SC70 KS-3 ADM809RAKSZ-REEL7 2.63 −40°C to +125°C M4D 3,000 3-Lead SC70 KS-3 ADM809RART-REEL 2.63 −40°C to +125°C 9RXX 10,000 3-Lead SOT-23 RT-3 ADM809RART-REEL7 2.63 −40°C to +125°C 9RXX 3,000 3-Lead SOT-23 RT-3 ADM809RARTZ-REEL 2.63 −40°C to +125°C M4D 10,000 3-Lead SOT-23 RT-3 ADM809RARTZ-REEL7 2.63 −40°C to +125°C M4D 3,000 3-Lead SOT-23 RT-3 ADM809SAKS-REEL 2.93 −40°C to +125°C M9E 10,000 3-Lead SC70 KS-3 ADM809SAKS-REEL7 2.93 −40°C to +125°C M9E 3,000 3-Lead SC70 KS-3 ADM809SAKSZ-REEL 2.93 −40°C to +125°C M53 10,000 3-Lead SC70 KS-3 ADM809SAKSZ-REEL7 2.93 −40°C to +125°C M53 3,000 3-Lead SC70 KS-3 ADM809SART-REEL7 2.93 −40°C to +125°C 9SXX 3,000 3-Lead SOT-23 RT-3 ADM809SARTZ-REEL 2.93 −40°C to +125°C M53 10,000 3-Lead SOT-23 RT-3 ADM809SARTZ-REEL7 2.93 −40°C to +125°C M53 3,000 3-Lead SOT-23 RT-3 ADM809TAKS-REEL7 3.08 −40°C to +125°C M9D 3,000 3-Lead SC70 KS-3 ADM809TAKSZ-REEL 3.08 −40°C to +125°C M4K 10,000 3-Lead SC70 KS-3 ADM809TAKSZ-REEL7 3.08 −40°C to +125°C M4K 3,000 3-Lead SC70 KS-3 ADM809TART-REEL7 3.08 −40°C to +125°C 9TXX 3,000 3-Lead SOT-23 RT-3 ADM809TARTZ-REEL 3.08 −40°C to +125°C 9TXX 10,000 3-Lead SOT-23 RT-3 ADM809TARTZ-REEL7 3.08 −40°C to +125°C 9TXX 3,000 3-Lead SOT-23 RT-3 ADM809ZAKS-REEL 2.32 −40°C to +125°C M9G 10,000 3-Lead SC70 KS-3 ADM809ZAKS-REEL7 2.32 −40°C to +125°C M9G 3,000 3-Lead SC70 KS-3 ADM809ZAKSZ-REEL 2.32 −40°C to +125°C M4P 10,000 3-Lead SC70 KS-3 Rev. I | Page 10 of 11

Data Sheet ADM803/ADM809/ADM810 Package Package Model1 Reset Threshold (V) Temperature Range Branding2, 3 Quantity Description Option ADM809ZAKSZ-REEL7 2.32 −40°C to +125°C M4P 3,000 3-Lead SC70 KS-3 ADM809ZART-REEL 2.32 −40°C to +125°C 9ZXX 10,000 3-Lead SOT-23 RT-3 ADM809ZARTZ-REEL 2.32 −40°C to +125°C M4P 10,000 3-Lead SOT-23 RT-3 ADM809ZARTZ-REEL7 2.32 −40°C to +125°C M4P 3,000 3-Lead SOT-23 RT-3 ADM810JAKSZ-REEL7 4.00 −40°C to +125°C M6V 3,000 3-Lead SC70 KS-3 ADM810JARTZ-REEL7 4.00 −40°C to +125°C M6V 3,000 3-Lead SOT-23 RT-3 ADM810LAKSZ-REEL7 4.63 −40°C to +125°C M6W or ALXX 3,000 3-Lead SC70 KS-3 ADM810LARTZ-REEL 4.63 −40°C to +125°C M6W or ALXX 10,000 3-Lead SOT-23 RT-3 ADM810LARTZ-REEL7 4.63 −40°C to +125°C M6W or ALXX 3,000 3-Lead SOT-23 RT-3 ADM810MAKSZ-REEL7 4.38 −40°C to +125°C M6S 3,000 3-Lead SC70 KS-3 ADM810MARTZ-REEL7 4.38 −40°C to +125°C M6S 3,000 3-Lead SOT-23 RT-3 ADM810RAKSZ-REEL7 2.63 −40°C to +125°C M52 or ARXX 3,000 3-Lead SC70 KS-3 ADM810RARTZ-REEL7 2.63 −40°C to +125°C M52 or ARXX 3,000 3-Lead SOT-23 RT-3 ADM810SAKSZ-REEL7 2.93 −40°C to +125°C M6T 3,000 3-Lead SC70 KS-3 ADM810SARTZ-REEL7 2.93 −40°C to +125°C M6T 3,000 3-Lead SOT-23 RT-3 ADM810TAKSZ-REEL7 3.08 −40°C to +125°C M4V 3,000 3-Lead SC70 KS-3 ADM810TARTZ-REEL7 3.08 −40°C to +125°C M4V 3,000 3-Lead SOT-23 RT-3 ADM810ZAKSZ-REEL7 2.32 −40°C to +125°C M6U 3,000 3-Lead SC70 KS-3 ADM810ZARTZ-REEL7 2.32 −40°C to +125°C M6U 3,000 3-Lead SOT-23 RT-3 1 Z = RoHS Compliant Part. 2 XX = Date code, may be top or bottom marked. 3 RoHS compliant part has XX branded on the bottom of the device. ©1997–2014 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D03736-0-10/14(I) Rev. I | Page 11 of 11

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: A nalog Devices Inc.: ADM810LARTZ-REEL7 ADM809-5LART-REEL ADM803TAKS-REEL7 ADM803LAKSZ-REEL7 ADM809ZAKS- REEL7 ADM809JAKS-REEL7 ADM803MAKS-REEL7 ADM809ZAKS-REEL ADM809-5LAKS-REEL ADM803SAKSZ- REEL ADM809-5LAKSZ-REEL ADM809RAKS-REEL7 ADM809-5SAKS-REEL ADM810MAKSZ-REEL7 ADM810JARTZ-REEL7 ADM810ZARTZ-REEL7 ADM810LARTZ-REEL ADM810RAKSZ-REEL7 ADM810RARTZ- REEL7 ADM809ZART-REEL ADM809SAKS-REEL ADM809RAKS-REEL ADM809SAKSZ-REEL ADM809JAKSZ- REEL ADM803TAKSZ-REEL7 ADM809TAKSZ-REEL ADM810MARTZ-REEL7 ADM810SAKSZ-REEL7 ADM810LAKSZ-REEL7 ADM810ZAKSZ-REEL7 ADM803SAKSZ-REEL7 ADM809MAKSZ-REEL ADM803SAKS- REEL7 ADM809-5SAKSZ-RL ADM803LAKSZ-REEL ADM809LAKSZ-REEL ADM810SARTZ-REEL7 ADM809RART- REEL ADM809-5LARTZ-REEL ADM803RAKSZ-REEL7 ADM809TAKS-REEL7 ADM809ZAKSZ-REEL ADM809LAKS-REEL7 ADM809SAKS-REEL7 ADM809-5SAKS-REEL7 ADM809-5LAKS-REEL7 ADM809MAKS- REEL7 ADM803MAKSZ-REEL7 ADM809ZARTZ-REEL ADM810JAKSZ-REEL7 ADM810TAKSZ-REEL7 ADM810TARTZ-REEL7