02/11/2015 www.crouzet.com DIN Rail Mount 35 mm HPC Part number 84874200 Allows control and monitoring of single phase and 3-phase pumps Monitors phase sequence and phase failure Checks for undercurrent to protect against running dry Checks for overcurrent to protect against overload Digitial inputs for operation control logic True RMS current measurement Part numbers Type Measurement ranges Nominal voltage (V) 84874200 HPC 1 A →10 A in DC 208 →480 V AC 3-phase 230 V monophase Specifications Supply Supply voltage Un 208 V.480 V 3-phase *230 V monophase Voltage supply tolerance -12 % / +10 % Operating range 183 →528 V AC AC supply voltage frequency 50/60 Hz ± 10 % Galvanic isolation of power supply/measurement No Power consumption at Un 5 VA in AC Immunity from micro power cuts 500 ms Inputs and measuring circuit Measurement ranges 1 →10 A AC E1-L2 : 1 →10 A Input resistance E1-L2 : 0,01 Ω Permanent overload at 25 °C E1-L2 : 11 A Pulse overload < 1 sec at 25 °C E1-L2 : 50 A Frequency of measured signal 50 / 60 Hz : ± 10 % Max. measuring cycle time 150 ms/True RMS measurement Adjustment of upper threshold 1 →10 A Adjustment of lower threshold 1 →10 A Fixed hysteresis 5 % of displayed treshold Display precision ±10 % of full scale Repetition accuracy with constant parameters ± 0,5 % Measuring error with voltage drift < ± 1 % across the whole range Measuring error with temperature drift ± 0,05 % / °C Timing Delays on power up (Ti) 1 →60 s (0, + 10 %) Delay on thresold crossing Tt 0,1 →10 s (0, + 10 %) Repetition accuracy with constant parameters ± 1 % Reset time 2 s Y2 minimum reset time 300 ms Delay on pick-up 500 ms Alarm on delay time max. 300 ms Output Type of output 1 single pole changeover relay Type of contacts No cadmium Maximum breaking voltage 250 V AC/DC Max. breaking current 5 A AC/DC Min. breaking current 10 mA / 5 V DC Electrical life (number of operations) 1 x 105 Breaking capacity (resistive) 1250 VA AC Maximum rate 360 operations/hour at full load Operating categories acc. to IEC/EN 60947-5-1 AC 12, AC 13, AC 14, AC 15, DC 12, DC 13 Mechanical life (operations) DC 14, 30 x 106 Insulation Nominal insulation voltage IEC/EN 60664-1 400 V Insulation coordination (IEC/EN 60664-1) Overvoltage category III : degree of pollution 3 Rated impulse withstand voltage (IEC/EN 60664-1) 4 kV (1,2 / 50 μs) Dielectric strength (IEC/EN 60664-1) 2 kV AC 50 Hz 1 min Insulation resistance (IEC/EN 60664-1) > 500 MΩ 500 V DC Unless otherwise specified, the characteristics given are applicable to all or part of the product range selected

02/11/2015 www.crouzet.com General characteristics Display power supply Green LED Display relay Yellow LED "Fault" indication Yellow LED Casing 35 mm Mounting On 35 mm symmetrical DIN rail, IEC/EN 60715 Mounting position All positions Material : enclosure plastic type VO to UL94 standard Incandescent wire test according to IEC 60695-2-11 & NF EN 60695-2-11 Protection (IEC/EN 60529) Terminal block : IP 20 Casing : IP 30 Weight 100 g Connecting capacity IEC/EN 60947-1 Rigid : 1 x 42 - 2 x 2.52 mm2 1 x 11 AWG - 2 x 14 AWG Flexible with ferrules : 1 x 2.52 - 2 x 1.52 mm2 1 x 14 AWG - 2 x 16 AWG Max. tightening torques IEC/EN 60947-1 0,6 →1 Nm / 5,3 →8,8 Lbf.In Operating temperature IEC/EN 60068-2 -20 →+50 °C Storage temperature IEC/EN 60068-2 -40 →+70 °C Humidity IEC/EN 60068-2-30 2 x 24 hr cycle 95 % RH max. without condensation 55 °C Vibrations according to IEC/EN60068-2-6 10 →150 Hz, A = 0.035 mm Shocks IEC/EN 60068-2-6 5 g Standards Marking CE (LVD) 73/23/EEC - EMC 89/336/EEC Product standard NF EN 60255-6 / IEC 60255-6 / UL 508 / CSA C22.2 N°14 Electromagnetic compatibility (EMC) Immunity EN 61000-6-2/IEC 61000-6-2 Emission EN 61000-6-4/EN 61000-6-3 IEC 61000-6-4/IEC 61000-6-3 Emission EN 55022 class B Certifications UL, CSA, GL Conformity with environmental directives RoHS, WEEE Comments Accessories Description Code Removable sealable cover for 35 mm casing 84800001 Principles Overview The pump controller can operate on a single phase or 3-phase network. It provides 3 functions in one unit : Checking current, Checking phase presence (in 3-phase mode), Checking phase sequence (in 3-phase mode). It has two operating modes whose purposes is to control a pump based on two external signal inputs (Y1 Y2). These two signals are controlled by volt-free contacts. Faults are signalled via LEDs, distinguishing the origin of the fault. Operating principle HPC Selecting the operating mode A rotary switch on the front is used to select : - single control mode, - dual control mode, - single-phase or 3-phase network. The position of this selector switch is only taken into account when the unit is powered up. If the switch position changes while the unit is operating, all the LEDs flash but the product continues to work normally with the mode selected on energisation prior to the change of position. The LEDs return to their normal state if the switch is reset to its initial position defined before the last energisation. Principles Unless otherwise specified, the characteristics given are applicable to all or part of the product range selected

02/11/2015 www.crouzet.com This mode is for controlling a pump based on one external signal (Y1). The relay output is closed when the signal is present at Y1 (contact closed). After a fault the relay remains open (even if the current returns to normal) and the module can be reclosed in two different ways : - By a reset : cutting of power supply, - Or by a reset through pressing an external contact (pushbutton for example) entering the second control input (Y2). No Legend Current fault Relay Fault monitoring inhibit time on pump start-up (Ti) Delay timing in case of fault (Tt) Principles This mode is for controlling a pump based on two external signals (Y1 and Y2). The output relay closes when both input signals are present (Y1 and Y2 closed). It will open as soon as either of these two signals is absent. If the controller is configured in single phase, it monitors the current drawn by the pump. If the controller is configured in 3-phase, it monitors current, phase sequence and phase failure. If a phase fault is detected, the output relay opens immediately. On energisation, the output relay cannot be closed if there is a phase fault or phase failure. No Legend Current fault Relay Fault monitoring inhibit time on pump start-up (Ti) Delay timing in case of fault (Tt) Principles Unless otherwise specified, the characteristics given are applicable to all or part of the product range selected

02/11/2015 www.crouzet.com Current control The under and overcurrent values are set by two independent potentiometers graduated from 1 to 10 A. In case of a control error (low threshold higher than high threshold), the output relay opens and all the LEDs flash to signal the error. If a current fault occurs (under or overcurrent) the relay opens if the fault persists beyond the preset threshold delay. When the current returns to a correct value, the output relay remains open. It can only be closed by a reset : either by de-energisation or by closing on external contact Y2 (in single control mode) An inhibit delay (Ti) on energisation allows current peaks due to start-up of the motor to be disregarded. No Legend Overcurrent Hysteresis Relay Fault monitoring inhibit time on pump start-up (Ti) Delay timing in case of fault (Tt) Principles Current control The under and overcurrent values are set by two independent potentiometers graduated from 1 to 10 A. In case of a control error (low threshold higher than high threshold), the output relay opens and all the LEDs flash to signal the error. If a current fault occurs (under or overcurrent) the relay opens if the fault persists beyond the preset threshold delay. When the current returns to a correct value, the output relay remains open. It can only be closed by a reset : either by de-energisation or by closing on external contact Y2 (in single control mode) An inhibit delay (Ti) on energisation allows current peaks due to start-up of the motor to be disregarded. No Legend Undercurrent Hysteresis Relay Fault monitoring inhibit time on pump start-up (Ti) Delay timing in case of fault (Tt) Dimensions (mm) HPC Unless otherwise specified, the characteristics given are applicable to all or part of the product range selected

02/11/2015 www.crouzet.com mm Connections 3 ph < 10 A No Legend 100 mA fast-blow fuse or cut-out Connections 1 ph AC 230 V < 10 A Unless otherwise specified, the characteristics given are applicable to all or part of the product range selected

02/11/2015 www.crouzet.com No Legend 100 mA fast-blow fuse or cut-out Connections 3 ph > 10 A No Legend 100 mA fast-blow fuse or cut-out Connections 1 ph AC 230 V > 10 A Unless otherwise specified, the characteristics given are applicable to all or part of the product range selected

02/11/2015 www.crouzet.com No Legend 100 mA fast-blow fuse or cut-out Connections CA 84874200 CA 84874200 Product adaptations Customisable colours and labels Fixed or adjustable time delay Fixed threshold in the generic range Unless otherwise specified, the characteristics given are applicable to all or part of the product range selected