Transient Voltage Suppression Diodes Axial Leaded – 5 kW > 5KP series 5KP Series RoHS Pb e3 Description The 5KP Series is designed specifically to protect sensitive Uni-directional electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Bi-directional • 5 kW peak pulse • Typical I less than 2μA R capability at 10/1000μs when V min>12V BR waveform, repetition rate • High temperature (duty cycles):0.01% to reflow soldering Agency Approvals • Glass passivated chip guaranteed: 260°C/40sec junction in P600 package / 0.375”, (9.5mm) lead AGENCY AGENCY FILE NUMBER • Fast response time: length, 5 lbs., (2.3kg) E230531 typically less than 1.0ps tension from 0 Volts to BV min • V @ T= V @25°C BR J BR Maximum Ratings and Thermal Characteristics • Excellent clamping x (1+αT x (TJ - 25)) (T =25OC unless otherwise noted) capability (αT:Temperature A Coefficient, typical value • Typical failure mode is is 0.1%) Parameter Symbol Value Unit short from over-specified voltage or current • UL Recognized compound Peak Pulse Power Dissipation by meeting flammability 10/1000μs Test Waveform (Fig.2) P 5 kW • Whisker test is conducted (Note 1) PPM based on JEDEC rating V-0 Steady State Power Dissipation on JESD201A per its table 4a • Matte tin lead–free plated P 8.0 W Infinite Heat Sink at T=75ºC D and 4c • Halogen free and RoHS L Peak Forward Surge Current, 8.3ms • IEC 61000-4-2 ESD compliant Single Half Sine Wave Unidirectional I 400 A FSM 30kV(Air), 30kV (Contact) • Pb-free E3 indicates that Only (Note 2) Maximum Instantaneous Forward • EFT protection of data 2nd level interconnect is Voltage at 100A for Unidirectional V 3.5/5.0 V lines in accordance with Pb-free and the terminal F Only (Note 3) IEC 61000-4-4 finish material is tin(Sn) Operating Junction and Storage T, T -55 to 175 °C • Low incremental surge (IPC/JEDEC J-STD- Temperature Range J STG 609A.01) resistance Typical Thermal Resistance R 8.0 °C/W Junction to Lead θJL Typical Thermal Resistance R 40 °C/W Applications Junction to Ambient θJA Notes: TVS componants are ideal for the protection of I/O 1. Non-repetitive current pulse , per Fig. 4 and derated above T (initial) =25OC per Fig. 3. J interfaces, V bus and other vulnerable circuits used in 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per CC telecom, computer, industrial and consumer electronic minute maximum. applications. 3. V < 3.5V for single die parts and V< 5.0V for stacked-die parts. F F Functional Diagram Additional Infomarion Bi-directional Datasheet Resources Samples Cathode Anode Uni-directional © 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/08/18

Transient Voltage Suppression Diodes Axial Leaded – 5 kW > 5KP series Electrical Characteristics (T=25°C unless otherwise noted) A Reverse Breakdown Test Maximum Maximum Maximum Agency NuPmarbt e r NuPmarbt e r VSotlatangde o Vff V(Vooltlatsg)e @ V BIR CurIre nt CVlaomltapgineg PPuelaske LReeavkeargsee Recognition (Uni) (Bi) R T T V @ I Current I I @ V (Volts) (mA) C PP PP R R MIN MAX (V) (A) (µ A) 5KP5.0A 5KP5.0CA 5.0 6.40 7.00 50 9.2 554.3 5000 X 5KP6.0A 5KP6.0CA 6.0 6.67 7.37 50 10.3 495.1 5000 X 5KP6.5A 5KP6.5CA 6.5 7.22 7.98 50 11.2 455.4 2000 X 5KP7.0A 5KP7.0CA 7.0 7.78 8.60 50 12.0 425.0 1000 X 5KP7.5A 5KP7.5CA 7.5 8.33 9.21 5 12.9 395.3 250 X 5KP8.0A 5KP8.0CA 8.0 8.89 9.83 5 13.6 375.0 150 X 5KP8.5A 5KP8.5CA 8.5 9.44 10.40 5 14.4 354.2 50 X 5KP9.0A 5KP9.0CA 9.0 10.00 11.10 5 15.4 331.2 20 X 5KP10A 5KP10CA 10.0 11.10 12.30 5 17.0 300.0 15 X 5KP11A 5KP11CA 11.0 12.20 13.50 5 18.2 280.2 2 X 5KP12A 5KP12CA 12.0 13.30 14.70 5 19.9 256.3 2 X 5KP13A 5KP13CA 13.0 14.40 15.90 5 21.5 237.2 2 X 5KP14A 5KP14CA 14.0 15.60 17.20 5 23.2 219.8 2 X 5KP15A 5KP15CA 15.0 16.70 18.50 5 24.4 209.0 2 X 5KP16A 5KP16CA 16.0 17.80 19.70 5 26.0 196.2 2 X 5KP17A 5KP17CA 17.0 18.90 20.90 5 27.6 184.8 2 X 5KP18A 5KP18CA 18.0 20.00 22.10 5 29.2 174.7 2 X 5KP20A 5KP20CA 20.0 22.20 24.50 5 32.4 157.4 2 X 5KP22A 5KP22CA 22.0 24.00 26.90 5 35.5 143.7 2 X 5KP24A 5KP24CA 24.0 26.70 29.50 5 38.9 131.1 2 X 5KP26A 5KP26CA 26.0 28.90 31.90 5 42.1 121.1 2 X 5KP28A 5KP28CA 28.0 31.10 34.40 5 45.4 112.3 2 X 5KP30A 5KP30CA 30.0 33.30 36.80 5 48.4 105.4 2 X 5KP33A 5KP33CA 33.0 36.70 40.60 5 53.3 95.7 2 X 5KP36A 5KP36CA 36.0 40.00 44.20 5 58.1 87.8 2 X 5KP40A 5KP40CA 40.0 44.40 49.10 5 64.5 79.1 2 X 5KP43A 5KP43CA 43.0 47.80 52.80 5 69.4 73.5 2 X 5KP45A 5KP45CA 45.0 50.00 55.30 5 72.7 70.2 2 X 5KP48A 5KP48CA 48.0 53.30 58.90 5 77.4 65.9 2 X 5KP51A 5KP51CA 51.0 56.70 62.70 5 82.4 61.9 2 X 5KP54A 5KP54CA 54.0 60.00 66.30 5 87.1 58.6 2 X 5KP58A 5KP58CA 58.0 64.40 71.20 5 93.6 54.5 2 X 5KP60A 5KP60CA 60.0 66.70 73.70 5 96.8 52.7 2 X 5KP64A 5KP64CA 64.0 71.10 78.60 5 103.0 49.5 2 X 5KP70A 5KP70CA 70.0 77.80 86.00 5 113.0 45.1 2 X 5KP75A 5KP75CA 75.0 83.30 92.10 5 121.0 42.1 2 X 5KP78A 5KP78CA 78.0 86.70 95.80 5 126.0 40.5 2 X 5KP85A 5KP85CA 85.0 94.40 104.00 5 137.0 37.2 2 X 5KP90A 5KP90CA 90.0 100.00 111.00 5 146.0 34.9 2 X 5KP100A 5KP100CA 100.0 110.00 123.00 5 162.0 31.5 2 X 5KP110A 5KP110CA 110.0 122.00 135.00 5 177.0 28.8 2 X 5KP120A 5KP120CA 120.0 133.00 147.00 5 193.0 26.4 2 X 5KP130A 5KP130CA 130.0 144.00 159.00 5 209.0 24.4 2 X 5KP150A 5KP150CA 150.0 167.00 185.00 5 243.0 21.0 2 X 5KP160A 5KP160CA 160.0 178.00 197.00 5 259.0 19.7 2 X 5KP170A 5KP170CA 170.0 189.00 209.00 5 275.0 18.5 2 X 5KP180A 5KP180CA 180.0 200.00 221.00 5 292.0 17.5 2 X 5KP190A 5KP190CA 190.0 211.00 233.00 5 310.0 16.5 2 - 5KP200A 5KP200CA 200.0 222.00 246.00 5 329.2 15.5 2 X 5KP210A 5KP210CA 210.0 233.00 258.00 5 349.5 14.6 2 - 5KP220A 5KP220CA 220.0 244.00 270.00 5 371.1 13.7 2 X 5KP250A 5KP250CA 250.0 277.00 306.00 5 425.0 12.0 2 X For bidirectional type having V of 10 volts and less, the I limit is double. R R For parts without A , the V is ± 10% and V is 5% higher than with A parts BR C © 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/08/18

Transient Voltage Suppression Diodes Axial Leaded – 5 kW > 5KP series I-V Curve Characteristics Uni-directional Bi-directional Ipp IT Vc VBRVR V Vc VBRVR IR V IRVF IR VRVBRVc IT IT Ipp Ipp P Peak Pulse Power Dissipation -- Max power dissipation PPM V Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation R V Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (I) BR T V Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) C I Reverse Leakage Current -- Current measured at V R R V Forward Voltage Drop for Uni-directional F Ratings and Characteristic Curves (T=25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Curve 1000 Voltage Transients W) TJ initial = Tamb K Voltage Across TVS wer ( 100 nt Po 5kW at 10x1000µs, 25°C Curre Current Through TVS ulse Voltage or -Peak PM 10 PPP 1 0.001 0.01 0.1 1 10 t-Pulse Width (ms) Time d continues on next page. © 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/08/18

Transient Voltage Suppression Diodes Axial Leaded – 5 kW > 5KP series Ratings and Characteristic Curves (T=25°C unless otherwise noted) (Continued) A Figure 3 - Peak Pulse Power Derating Curve Figure 4 - Pulse Waveform 150 100 k Pulse Power (P) or Current (I)PPPPDerating in Percentage % 257505 I- Peak Pulse Current, % IPPMRSM 15000 tr=1PI0PeµPasMke cVaHIlPuaPelMf Va(lI Pu P1a2eTPac0sM usuJ / rd1=)ltrsh02eeee50nfi W °0tpnC dµioedeisdtnceh tabc( wyt.yds hW ) R teiosar. E ev5d .0eteAh%ffieon orpemfde IaPkP M a Pe 0 td 0 25 50 75 100 125 150 175 200 0 0 1.0 2.0 3.0 4.0 TJ - Initial Junction Temperature (ºC) t-Time (ms) Figure 5 - Typical Junction Capacitance Figure 6 - Typical Transient Thermal Impedance 100 100000 Uni-direc(cid:31)onal V=0V W) C/ 10000 Bi-direc(cid:31)onal V=0V e (° c an 10 pF) 1000 Uni-direc(cid:31)onal V=VR ped Cj ( al Im m 100 Bi-direc(cid:31)onal V=VR Ther 1 nt 10 sie n a Tr 1 0.1 1 10 100 1000 0.01 0.1 1 10 100 1000 V - Reverse Breakdown Voltage (V) BR TP-Pulse Duration (s) Figure 7 - Maximum Non-Repetitive Peak Forward Figure 8 - Peak Forward Voltage Drop vs Peak Forward Surge Current Uni-Directional Only Current (Typical Values) 500 100 Single die A) 450 Surge Current ( 334050000 d Current(A) 10 Stacked-die ard 250 war 1 Forw 200 For ak ak Pe 150 Pe 0.1 -FSM 100 I-F I 50 0.01 0 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 1 10 100 Number of Half Cycles at 60 Hz VF-Peak Forward Voltage(V) © 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/08/18

Transient Voltage Suppression Diodes Axial Leaded – 5 kW > 5KP series Soldering Parameters Lead–free Reflow Condition assembly TP tp - Temperature Min (T ) 150°C Ramp-up Critical Zone Pre Heat - Temperature Max (Tss(m(mina)x)) 200°C T) TL tL TL to TP Atov epreaagke ram- pT iumpe r a(mtei n(L tioq umidauxs) T(tes)mp (TA) 630°C –/ s1e8c0o nsde cmsax (Temperature TTss((mmainx)) Prethseat Ramp-down T to T - Ramp-up Rate 3°C/second max S(max) A - Temperature (T ) (Liquidus) 217°C 25˚C t 25˚C to Peak Reflow A Time (t) - Time (min to max) (t) 60 – 150 seconds s Peak Temperature (T) 260+0/-5 °C P Time within 5°C of actual peak Flow/Wave Soldering (Solder Dipping) 20 – 40 seconds Temperature (t) p Ramp-down Rate 6°C/second max Peak Temperature : 265OC Time 25°C to peak Temperature (T) 8 minutes Max. Dipping Time : 10 seconds P Do not exceed 260°C Soldering : 1 time Physical Specifications Environmental Specifications Weight 0.07oz., 2.1g High Temp. Storage JESD22-A103 P600 molded plastic body over Case passivated junction. HTRB JESD22-A108 Color band denotes the cathode except Polarity Temperature Cycling JESD22-A104 Bipolar. Matte Tin axial leads, solderable per H3TRB JESD22-A101 Terminal JESD22-B102. RSH JESD22-B106 Dimensions Inches Millimeters Cathode Band Dimensions D (for uni-directional products only) Min Max Min Max A 1.000 - 25.40 - C B 0.340 0.360 8.60 9.10 A B A C 0.048 0.054 1.22 1.36 D 0.340 0.360 8.60 9.10 P600 © 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/08/18

Transient Voltage Suppression Diodes Axial Leaded – 5 kW > 5KP series Part Numbering System Part Marking System 5KPxxxXXX Cathode Band OPTION CODE: (for uni-directional BLANK Reel Tape products only) F -B Bulk Packaging YYWW Littelfuse Logo Trace Code Marking TYPE CODE: YY:Year Code A Uni-Directional (5% VBR Voltage Tolerance) WW: Week Code CA Bi-Directional (5% V Voltage Tolerance) BR 5KPXXX Product Type V VOLTAGE R SERIES CODE Packing Options Component Packaging Part Number Quantity Packaging Specification Package Option 5KPxxxXX P600 800 Tape & Reel EIA STD RS-296 5KPxxxXX-B P600 100 BULK Littelfuse Spec. Tape and Reel Specification Off Center 2.56 either side 2.063+0.079/-0.039 (65.0) (53.0+2.0/-1.0) 0.028(0.7) 0.047 0.236 (1.2) (6.0) 0.394+/-0.020 (10.0+/-0.5) Dimensions are in 13.0 inches/mm (330.2) 3.0 (76.2) 0.68 (17.27) 2.75 (69.85) Direction of Feed Recess Depth Max. 0.75 (19.05) Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. © 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/08/18