597D www.vishay.com Vishay Sprague Solid Tantalum Chip Capacitors, TANTAMOUNT™, Ultra-Low ESR, Conformal Coated, Maximum CV FEATURES • New case size offerings • Terminations: 100 % tin (2) standard; tin / lea d available Available • Extremely low ESR Available • Mounting: surface mount • Ripple current up to 4.1 A PERFORMANCE CHARACTERISTICS • Material categorization: for definitions of complianc e www.vishay.com/doc?40194 please see www.vishay.com/doc?99912 Operating Temperature: -55 °C to +125 °C (above 85 °C, voltage derating is required) Note Capacitance Range: 10 μF to 2200 μF * This datasheet provides information about parts that are Capacitance Tolerance: ± 10 %, ± 20 % standard RoHS-compliant and / or parts that are non RoHS-compliant. For Voltage Rating: 4 V to 75 V example, parts with lead (Pb) terminations are not RoHS-compliant. DC DC Please see the information / tables in this datasheet for details Moisture Sensitivity Level 2a ORDERING INFORMATION 597D 687 X0 6R3 E 2 T TYPE CAPACITANCE CAPACITANCE DC VOLTAGE RATING CASE CODE TERMINATION REEL SIZE AND TOLERANCE AT +85 °C PACKAGING This is expressed in pF. X0 = ± 20 % This is expressed in V. See Ratings 2 = 100 % tin T = tape and reel The first two digits are X9 = ± 10 % To complete the three-digit and Case 8 = solder plated 7" [178 mm] reel the significant figures. block, zeros precede the Codes table (60/40) The third is the number voltage rating. A decimal special order of zeros to follow. point is indicated by an “R” (6R3 = 6.3 V). Note • Preferred tolerance and reel sizes are in bold. We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. Low ESR solid tantalum chip capacitors allow delta ESR of 1.25 times the datasheet limits after mounting DIMENSIONS in inches [millimeters] Tantalum wire nib identifies J anode (+) W terminal L H D B A CASE CODE L (MAX.) W H A B D (REF.) J (MAX.) 0.299 0.173 ± 0.016 0.079 0.051 ± 0.012 0.181 ± 0.024 0.252 0.004 V [7.6] [4.4 ± 0.4] [2.0 max.] [1.3 ± 0.3] [4.6 ± 0.6] [6.4] [0.1] 0.299 0.173 ± 0.016 0.138 0.051 ± 0.012 0.181 ± 0.024 0.252 0.004 D [7.6] [4.4 ± 0.4] [3.5 max.] [1.3 ± 0.3] [4.6 ± 0.6] [6.4] [0.1] 0.299 0.173 ± 0.016 0.157 ± 0.016 0.051 ± 0.012 0.181 ± 0.024 0.252 0.004 E [7.6] [4.4 ± 0.4] [4.0 ± 0.4] [1.3 ± 0.3] [4.6 ± 0.6] [6.4] [0.1] 0.299 0.238 ± 0.016 0.142 ± 0.016 0.051 ± 0.012 0.181 ± 0.024 0.244 0.004 R [7.6] [6.0 ± 0.4] [3.6 ± 0.4] [1.3 ± 0.3] [4.6 ± 0.6] [6.2] [0.1] 0.299 0.238 ± 0.016 0.185 ± 0.016 0.055 ± 0.016 0.181 ± 0.024 0.244 0.004 F [7.6] [6.0 ± 0.4] [4.7 ± 0.4] [1.4 ± 0.4] [4.6 ± 0.6] [6.2] [0.1] 0.299 0.238 ± 0.016 0.236 ± 0.016 0.055 ± 0.016 0.181 ± 0.024 0.244 0.004 Z [7.6] [6.0 ± 0.4] [6.0 ± 0.4] [1.4 ± 0.4] [4.6 ± 0.6] [6.2] [0.1] 0.315 0.260 + 0.016 / - 0.024 0.142 ± 0.016 0.051 ± 0.012 0.197 ± 0.024 0.260 0.004 M [8.0] [6.6 + 0.4 / - 0.6] [3.6 ± 0.4] [1.3 ± 0.3] [5.0 ± 0.6] [6.6] [0.1] 0.315 0.260 + 0.016 / - 0.024 0.205 ± 0.016 0.055 ± 0.016 0.197 ± 0.024 0.260 0.004 H [8.0] [6.6 + 0.4 / - 0.6] [5.2 ± 0.4] [1.4 ± 0.4] [5.0 ± 0.6] [6.6] [0.1] Note • The anode termination (D less B) will be a minimum of 0.012" [0.3 mm] Revision: 16-Jul-2019 1 Document Number: 40047 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

597D www.vishay.com Vishay Sprague RATINGS AND CASE CODES μF 4 V 6.3 V 10 V 16 V 20 V 25 V 35 V 40 V 50 V 63 V 75 V 10 D R 15 E / R R R / F 22 R F Z / H 33 F H / Z 47 R H / Z 68 R F 100 F F / H H 150 F 220 E R M 330 V E F H 470 V E E H H 680 E E R H 1000 E / R R F 1500 R F 2200 R STANDARD RATINGS MAX. DF MAX. ESR MAX. RIPPLE MAX. DCL CAPACITANCE AT +25 °C AT +25 °C 100 kHz CASE CODE PART NUMBER AT +25 °C (μF) 120 Hz 100 kHz I (μA) (%) (mΩ) R(AM)S 4 V AT +85 °C; 2.7 V AT +125 °C DC DC 470 V 597D477(1)004V(2)(3) 19 8 60 2.2 680 E 597D687(1)004E(2)(3) 27 6 25 2.9 1000 E 597D108(1)004E(2)(3) 40 8 20 3.3 1000 R 597D108(1)004R(2)(3) 40 8 18 3.7 1500 R 597D158(1)004R(2)(3) 60 8 24 2.9 2200 R 597D228(1)004R(2)(3) 88 30 35 2.7 6.3 V AT +85 °C; 4 V AT +125 °C DC DC 330 V 597D337(1)6R3V(2)(3) 21 8 56 2.0 470 E 597D477(1)6R3E(2)(3) 30 6 30 2.7 680 E 597D687(1)6R3E(2)(3) 43 6 25 2.9 1000 R 597D108(1)6R3R(2)(3) 63 8 31 2.8 1500 F 597D158(1)6R3F(2)(3) 94 30 35 2.7 10 V AT +85 °C; 7 V AT +125 °C DC DC 330 E 597D337(1)010E(2)(3) 33 6 35 2.5 470 E 597D477(1)010E(2)(3) 47 6 28 2.8 680 R 597D687(1)010R(2)(3) 68 6 28 3.0 1000 F 597D108(1)010F(2)(3) 100 20 120 1.4 16 V AT +85 °C; 10 V AT +125 °C DC DC 220 E 597D227(1)016E(2)(3) 35 8 60 2.3 330 F 597D337(1)016F(2)(3) 53 10 100 1.6 470 H 597D477(1)016H(2)(3) 75 14 100 1.4 680 H 597D687(1)016H(2)(3) 100 20 80 1.8 Note • Part number definitions: (1) Tolerance: for 10 % tolerance, specify “X9”, for 20 % tolerance, change to “X0” (2) Termination: for 100 % tin specify “2”, for solder plated 60/40 specify “8” (3) Packaging code: for 7" reels specify “T” Revision: 16-Jul-2019 2 Document Number: 40047 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

597D www.vishay.com Vishay Sprague STANDARD RATINGS MAX. DF MAX. ESR MAX. RIPPLE MAX. DCL CAPACITANCE AT +25 °C AT +25 °C 100 kHz CASE CODE PART NUMBER AT +25 °C (μF) 120 Hz 100 kHz I (μA) (%) (mΩ) R(AM)S 20 V AT +85 °C; 13 V AT +125 °C DC DC 220 R 597D227(1)020R(2)(3) 44 8 80 1.8 330 H 597D337(1)020H(2)(3) 66 10 100 1.6 470 H 597D477(1)020H(2)(3) 94 14 100 1.6 25 V AT +85 °C; 17 V AT +125 °C DC DC 68 R 597D686(1)025R(2)(3) 17 6 100 1.6 100 F 597D107(1)025F(2)(3) 25 8 100 1.6 150 F 597D157(1)025F(2)(3) 38 8 80 1.8 220 M 597D227(1)025M(2)(3) 55 8 100 1.6 35 V AT +85 °C; 23 V AT +125 °C DC DC 47 R 597D476(1)035R(2)(3) 17 6 100 1.6 68 F 597D686(1)035F(2)(3) 24 6 100 1.6 100 F 597D107X0035F(2)(3) 35 8 100 1.6 100 H 597D107(1)035H(2)(3) 35 8 100 1.4 40 V AT +85 °C; 26 V AT +125 °C DC DC 100 H 597D107X0040H(2)(3) 40 10 150 1.3 50 V AT +85 °C; 33 V AT +125 °C DC DC 15 E 597D156(1)050E(2)(3) 8 6 300 0.9 15 R 597D156(1)050R(2)(3) 8 6 250 1.0 22 R 597D226(1)050R(2)(3) 11 6 220 1.1 33 F 597D336(1)050F(2)(3) 17 6 150 1.3 47 H 597D476X(1)050H(2)(3) 23.5 8 400 0.8 47 Z 597D476(1)050Z(2)(3) 24 6 240 1.1 63 V AT +85 °C; 42 V AT +125 °C DC DC 10 D 597D106(1)063D(2)(3) 10 6 400 0.6 15 R 597D156(1)063R(2)(3) 10 6 400 0.8 22 F 597D226(1)063F(2)(3) 14 6 250 1.0 33 H 597D336X(1)063H(2)(3) 20.8 8 500 0.7 33 Z 597D336(1)063Z(2)(3) 20.8 8 500 0.7 75 V AT +85 °C; 50 V AT +125 °C DC DC 10 R 597D106(1)075R(2)(3) 8 6 500 0.7 15 R 597D156X0075R(2)(3) 12 6 500 0.7 15 F 597D156X0075F(2)(3) 12 6 500 0.7 22 Z 597D226(1)075Z(2)(3) 16.5 6 400 0.8 22 H 597D226(1)075H(2)(3) 16.5 6 400 0.8 Note • Part number definitions: (1) Tolerance: for 10 % tolerance, specify “X9”, for 20 % tolerance, change to “X0” (2) Termination: for 100 % tin specify “2”, for solder plated 60/40 specify “8” (3) Packaging code: for 7" reels specify “T” Revision: 16-Jul-2019 3 Document Number: 40047 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

597D www.vishay.com Vishay Sprague TYPICAL CURVES ESR AND Z VS. FREQUENCY 1500 μF -4 V, Case Size “R” 330 μF -10 V, Case Size “E” 1 10000 1 10000 R (Ω) Z 1000 R (Ω) 1000 2nd lineance / ES 0.1 1st line2nd line 2nd lineance / ES 0.1 Z 1st line2nd line ed 100 ed 100 p p Im ESR Im ESR 0.01 10 0.01 10 0.1 1 10 100 1000 0.1 1 10 100 1000 Frequency (kHz) Frequency (kHz) 330 μF -6.3 V, Case Size “V” 1000 μF -6.3 V, Case Size “R” 10 10000 1 10000 R (Ω) 1 1000 R (Ω) 1000 2nd lineance / ES Z 1st line2nd line 2nd lineance / ES 0.1 Z 1st line2nd line ed 0.1 100 ed 100 p p m ESR m ESR I I 0.01 10 0.01 10 0.1 1 10 100 1000 0.1 1 10 100 1000 Frequency (kHz) Frequency (kHz) 470 μF -4 V, Case Size “V” 10 10000 R (Ω) 1 1000 2nd lineance / ES Z 1st line2nd line ed 0.1 100 p ESR m I 0.01 10 0.1 1 10 100 1000 Frequency (kHz) Revision: 16-Jul-2019 4 Document Number: 40047 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

597D www.vishay.com Vishay Sprague POWER DISSIPATION CASE CODE MAXIMUM PERMISSIBLE POWER DISSIPATION AT +25 °C (W) IN FREE AIR V 0.141 D 0.215 E 0.240 R, F, M 0.250 Z 0.265 H 0.265 STANDARD PACKAGING QUANTITY CASE CODE UNITS PER 7" REEL V 1000 D 400 E 500 R 300 F 250 Z 250 M 200 H 200 PRODUCT INFORMATION Conformal Coated Guide Pad Dimensions www.vishay.com/doc?40150 Packaging Dimensions Moisture Sensitivity (MSL) www.vishay.com/doc?40135 SELECTOR GUIDES Solid Tantalum Selector Guide www.vishay.com/doc?49053 FAQ Frequently Asked Questions www.vishay.com/doc?40110 Revision: 16-Jul-2019 5 Document Number: 40047 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague Guide for Conformal Coated Tantalum Capacitors INTRODUCTION Rating for rating, tantalum capacitors tend to have as much as three times better capacitance / volume efficiency than Tantalum electrolytic capacitors are the preferred choice in aluminum electrolytic capacitors. An approximation of the applications where volumetric efficiency, stable electrical capacitance / volume efficiency of other types of capacitor s parameters, high reliability, and long service life are primary may be inferred from the following table, which shows the considerations. The stability and resistance to elevated dielectric constant ranges of the various materials used i n temperatures of the tantalum / tantalum oxide / manganes e each type. Note that tantalum pentoxide has a dielectri c dioxide system make solid tantalum capacitors an constant of 26, some three times greater than that of appropriate choice for today's surface mount assembly aluminum oxide. This, in addition to the fact that extremel y technology. thin films can be deposited during the electrolytic proces s Vishay Sprague has been a pioneer and leader in this field, mentioned earlier, makes the tantalum capacitor extremely producing a large variety of tantalum capacitor types for efficient with respect to the number of microfarads available consumer, industrial, automotive, military, and aerospac e per unit volume. The capacitance of any capacitor i s electronic applications. determined by the surface area of the two conducting Tantalum is not found in its pure state. Rather, it is plates, the distance between the plates, and the dielectric commonly found in a number of oxide minerals, often in constant of the insulating material between the plates. combination with Columbium ore. This combination is known as “tantalite” when its contents are more than COMPARISON OF CAPACITOR one-half tantalum. Important sources of tantalite include DIELECTRIC CONSTANTS Australia, Brazil, Canada, China, and several African countries. Synthetic tantalite concentrates produced from e DIELECTRIC tin slags in Thailand, Malaysia, and Brazil are also a DIELECTRIC CONSTANT significant raw material for tantalum production. Air or vacuum 1.0 Electronic applications, and particularly capacitors , Paper 2.0 to 6.0 consume the largest share of world tantalum production . Other important applications for tantalum include cuttin g Plastic 2.1 to 6.0 tools (tantalum carbide), high temperature super alloys , Mineral oil 2.2 to 2.3 chemical processing equipment, medical implants, and military ordnance. Silicone oil 2.7 to 2.8 Vishay Sprague is a major user of tantalum materials in the Quartz 3.8 to 4.4 form of powder and wire for capacitor elements and rod an d Glass 4.8 to 8.0 sheet for high temperature vacuum processing. Porcelain 5.1 to 5.9 THE BASICS OF TANTALUM CAPACITORS Mica 5.4 to 8.7 Most metals form crystalline oxides which are Aluminum oxide 8.4 non-protecting, such as rust on iron or black oxide on copper. A few metals form dense, stable, tightly adhering, Tantalum pentoxide 26 electrically insulating oxides. These are the so-called “valve” Ceramic 12 to 400K metals and include titanium, zirconium, niobium, tantalum, hafnium, and aluminum. Only a few of these permit the In the tantalum electrolytic capacitor, the distance betwee n accurate control of oxide thickness by electrochemical the plates is very small since it is only the thickness of the means. Of these, the most valuable for the electronic s tantalum pentoxide film. As the dielectric constant of th e industry are aluminum and tantalum. tantalum pentoxide is high, the capacitance of a tantalu m Capacitors are basic to all kinds of electrical equipment, capacitor is high if the area of the plates is large: from radios and television sets to missile controls and eA C = ------- automobile ignitions. Their function is to store an electrical t charge for later use. where Capacitors consist of two conducting surfaces, usually C = capacitance metal plates, whose function is to conduct electricity. They e = dielectric constant are separated by an insulating material or dielectric. The dielectric used in all tantalum electrolytic capacitors is A = surface area of the dielectric tantalum pentoxide. t = thickness of the dielectric Tantalum pentoxide compound possesses high-dielectri c Tantalum capacitors contain either liquid or solid strength and a high-dielectric constant. As capacitors are electrolytes. In solid electrolyte capacitors, a dry material being manufactured, a film of tantalum pentoxide is applied (manganese dioxide) forms the cathode plate. A tantalum to their electrodes by means of an electrolytic process. Th e lead is embedded in or welded to the pellet, which is in turn film is applied in various thicknesses and at various voltage s connected to a termination or lead wire. The drawings sho w and although transparent to begin with, it takes on differen t the construction details of the surface mount types o f colors as light refracts through it. This coloring occurs on the tantalum capacitors shown in this catalog. tantalum electrodes of all types of tantalum capacitors. Revision: 10-Mar-2020 1 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague SOLID ELECTROLYTE TANTALUM CAPACITORS TYPE 194D Solid electrolyte capacitors contain manganese dioxide , which is formed on the tantalum pentoxide dielectric laye r SnPb or Gold Plated Ni Cathode by impregnating the pellet with a solution of manganous End Cap Termination Encapsulation nitrate. The pellet is then heated in an oven, and the manganous nitrate is converted to manganese dioxide. SnPb or Gold Plated Ni Anode End Cap Termination The pellet is next coated with graphite, followed by a laye r Cathode of metallic silver, which provides a conductive surface Backfill between the pellet and the can in which it will be enclosed. After assembly, the capacitors are tested and inspected to assure long life and reliability. It offers excellent reliability and high stability for consumer and commercial electronic s Conductive Silver with the added feature of low cost. Epoxy Adhesive Surface mount designs of “Solid Tantalum” capacitors us e Sintered Tantalum Sponge Teflon lead frames or lead frameless designs as shown in the Pellet accompanying drawings. MnO/Carbon/ Anode Backfill 2 Silver Coating TANTALUM CAPACITORS FOR ALL DESIGN CONSIDERATIONS TYPE T96 Solid electrolyte designs are the least expensive for a given rating and are used in many applications where their very Intermediate Fuse small size for a given unit of capacitance is of importance. Cathode They will typically withstand up to about 10 % of the rated Silver DC working voltage in a reverse direction. Also importan t are their good low temperature performance characteristic s and freedom from corrosive electrolytes. Vishay Sprague patented the original solid electrolyt e capacitors and was the first to market them in 1956. Visha y Sprague has the broadest line of tantalum capacitors and has continued its position of leadership in this field. Data sheets covering the various types and styles of Visha y Cathode Termination MnO/Carbon/ Sprague capacitors for consumer and entertainment (Silver + Ni/Sn or 2 Silver Coating electronics, industry, and military applications are availabl e Ni/SnPb Plating) where detailed performance characteristics must be Encapsulation Epoxy Tower/ specified. Anode Termination Sponge Teflon (Silver + Ni/Sn or Sintered Tantalum TYPE 195D, 572D, 591D, 592D / W, 594D, Ni/SnPb Plating) Pellet 595D, 695D, T95, 14002 Cathode Termination TYPE T98 (Silver + Ni/Sn/Plating) Encapsulation Fuse Anode Termination Intermediate (Silver + Ni/Sn/Plating) Cathode Silver MnO2/Carbon/Silver Coating Sintered Tantalum Pellet Sponge Teflon/Epoxy Tower TYPE 597D / T97 / 13008 Cathode Termination (Silver + Ni/Sn or MnO/Carbon/ Cathode Termination Ni/SnPb Plating) Silve2r Coating (Silver + Ni/Sn/Plating) Encapsulation Encapsulation Anode Termination Epoxy Tower/ (Silver + Ni/Sn/Plating) Anode Termination Sponge Teflon (Silver + Ni/Sn or Sintered Tantalum Ni/SnPb Plating) Pellet MnO/Carbon/Silver 2 Coating Sintered Tantalum Silver Epoxy Pellet Sponge Teflon/Epoxy Tower Revision: 10-Mar-2020 2 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague COMMERCIAL PRODUCTS SOLID TANTALUM CAPACITORS - CONFORMAL COATED SERIES 592W 592D 591D 595D 594D PRODUCT IMAGE TYPE Surface mount TANTAMOUNT™ chip, conformal coated Low profile, robust Low profile, Low profile, low ESR, Low ESR, FEATURES design for use in Maximum CV maximum CV maximum CV maximum CV pulsed applications -55 °C to +125 °C TEMPERATURE (above 40 °C, voltage -55 °C to +125 °C (above 85 °C, voltage derating is required) RANGE deratig is required) CAPACITANCE 330 μF to 2200 μF 1 μF to 2200 μF 1 μF to 1500 μF 0.1 μF to 1500 μF 1 μF to 1500 μF RANGE VOLTAGE RANGE 6 V to 10 V 4 V to 50 V 4 V to 50 V 4 V to 50 V 4 V to 50 V CAPACITANCE ± 20 % ± 10 %, ± 20 % ± 10 %, ± 20 % ± 10 %, ± 20 % ± 10 %, ± 20 % TOLERANCE LEAKAGE 0.01 CV or 0.5 μA, whichever is greater CURRENT DISSIPATION 14 % to 45 % 4 % to 50 % 4 % to 50 % 4 % to 20 % 4 % to 20 % FACTOR T, S, A, B, C, CASE CODES C, M, X S, A, B, C, D, R, M, X A, B, C, D, R, M B, C, D, R D, G, M, R TERMINATION 100 % matte tin 100 % matte tin standard, tin / lead and gold plated available SOLID TANTALUM CAPACITORS - CONFORMAL COATED SERIES 597D 572D 695D 195D 194D PRODUCT IMAGE TYPE TANTAMOUNT™ chip, conformal coated Ultra low ESR, Low profile, Pad compatible with US and European Industrial version of FEATURES maximum CV, maximum CV 194D and CWR06 case sizes CWR06 / CWR16 multi-anode TEMPERATURE -55 °C to +125 °C (above 85 °C, voltage derating is required) RANGE CAPACITANCE 10 μF to 2200 μF 2.2 μF to 220 μF 0.1 μF to 270 μF 0.1 μF to 330 μF 0.1 μF to 330 μF RANGE VOLTAGE RANGE 4 V to 75 V 4 V to 35 V 4 V to 50 V 2 V to 50 V 4 V to 50 V CAPACITANCE ± 10 %, ± 20 % TOLERANCE LEAKAGE 0.01 CV or 0.5 μA, whichever is greater CURRENT DISSIPATION 6 % to 20 % 6 % to 26 % 4 % to 8 % 4 % to 8 % 4 % to 10 % FACTOR C, S, V, X, Y, Z, R, CASE CODES V, D, E, R, F, Z, M, H P, Q, S, A, B, T A, B, D, E, F, G, H A, B, C, D, E, F, G, H A, B, D, E, F, G, H 100 % matte tin Gold plated standard; 100 % matte tin standard, tin / lead 100 % matte tin standard, tin / lead solder plated TERMINATION standard, gold plated solder plated tin / lead and gold plated available and hot solder available available dipped available Revision: 10-Mar-2020 3 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague HIGH RELIABILITY PRODUCTS SOLID TANTALUM CAPACITORS - CONFORMAL COATED SERIES CWR06 CWR16 CWR26 13008 14002 PRODUCT IMAGE TYPE TANTAMOUNT™ chip, conformal coated MIL-PRF-55365/4 MIL-PRF-55365/13 MIL-PRF-55365/13 FEATURES DLA approved qualified qualified qualified TEMPERATURE RANGE -55 °C to +125 °C (above 85 °C, voltage derating is required) CAPACITANCE RANGE 0.10 μF to 100 μF 0.33 μF to 330 μF 10 μF to 100 μF 10 μF to 1500 μF 4.7 μF to 680 μF VOLTAGE RANGE 4 V to 50 V 4 V to 35 V 15 V to 35 V 4 V to 63 V 4 V to 50 V ± 5 %, ± 10 %, ± 5 %, ± 10 %, ± 5 %, ± 10 %, CAPACITANCE TOLERANCE ± 10 %, ± 20 % ± 10 %, ± 20 % ± 20 % ± 20 % ± 20 % LEAKAGE CURRENT 0.01 CV or 1.0 μA, whichever is greater 0.01 CV or 0.5 μA, whichever is greater DISSIPATION FACTOR 6 % to 10 % 6 % to 10 % 6 % to 12 % 6 % to 20 % 6 % to 14 % A, B, C, D, E, F, G, A, B, C, D, E, F, G, V, E, F, R, Z, D, M, CASE CODES F, G, H B, C, D, R H H H, N TERMINATION Gold plated; tin / lead; tin / lead solder fused Tin / lead SOLID TANTALUM CAPACITORS - CONFORMAL COATED SERIES T95 T96 T97 T98 PRODUCT IMAGE TYPE TANTAMOUNT™ chip, Hi-Rel COTS, conformal coated High reliability, High reliability, High reliability, FEATURES High reliability ultra low ESR, ultra low ESR, built in built in fuse multi-anode fuse, multi-anode TEMPERATURE RANGE -55 °C to +125 °C (above 85 °C, voltage derating is required) CAPACITANCE RANGE 0.15 μF to 680 μF 10 μF to 680 μF 10 μF to 2200 μF 10 μF to 1500 μF VOLTAGE RANGE 4 V to 50 V 4 V to 50 V 4 V to 75 V 4 V to 75 V CAPACITANCE TOLERANCE ± 10 %, ± 20 % ± 10 %, ± 20 % ± 10 %, ± 20 % ± 10 %, ± 20 % LEAKAGE CURRENT 0.01 CV or 0.5 μA, whichever is greater DISSIPATION FACTOR 4 % to 14 % 6 % to 14 % 6 % to 20 % 6 % to 10 % CASE CODES A, B, C, D, R, S, V, X, Y, Z R V, E, F, R, Z, D, M, H, N V, E, F, R, Z, M, H TERMINATION 100 % matte tin, tin / lead Revision: 10-Mar-2020 4 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague TAPE AND REEL PACKAGING in inches [millimeters] 0.157 ± 0.004 (m Ta2x.) [4.0 ± 0.10] 1to0l epri atcnhcees o cnu tmapuelative Deformation 0.059 + 0.004 - 0.0 ± 0.008 [0.200] between [1.5 + 0.10 - 0.0] Embossment 0.024 embossments 0.079 ± 0.002 0.069 ± 0.004 [0.600] [2.0 ± 0.05] [1.75 ± 0.10] max. Top ctaopveer A0 0.0m30in .[0 (3.7)5] F W 20° B1 (max.) (6) K0Top B0 0.030 [0.75] Mcrooatmaxtipimoonunment cover min. (4) tape (Side or front sectional view) Center lines P For tape feeder 0.004 [0.10] of cavity 1 D1 (min.) for components reference only max. 0.079 x 0.047 [2.0 x 1.2] and l.arger (5) including draft. USER DIRECTION Concentric around B0 OF FEED Mcaavxitimy suimze (1) Cathode (-) R minimum: Anode (+) R 8 mm = 0.984" (25 mm) min. 12 mm and 16 mm = 1.181" (30 mm) DIRECTION OF FEED Bending radius (2) Tape and reel specifications: all case sizes are 3.937 [100.0] available on plastic embossed tape per EIA-481. 20° maximum Standard reel diameter is 7" (178 mm). component rotation 0.039 [1.0] Typical max. Lengthwise orientation at capacitors in tape component Tape cavity 0.039 [1.0] Cathode (-) B0 center line max. 0.9843 [250.0] Typical Camber component (Top view) A0 center line Allowable camber to be 0.039/3.937 [1/100] (Top view) Non-cumulative over 9.843 [250.0] Anode (+) DIRECTION OF FEED H-Case only Notes • Metric dimensions will govern. Dimensions in inches are rounded and for reference only (1) A , B , K , are determined by the maximum dimensions to the ends of the terminals extending from the component body and / or the bod y 0 0 0 dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the cavity (A , B , K ) must be within 0.002" (0.05 mm) minimum and 0.020" (0.50 mm) maximum. The clearance allowed must also prevent 0 0 0 rotation of the component within the cavity of not more than 20° (2) Tape with components shall pass around radius “R” without damage. The minimum trailer length may require additional length to provide “R” minimum for 12 mm embossed tape for reels with hub diameters approaching N minimum (3) This dimension is the flat area from the edge of the sprocket hole to either outward deformation of the carrier tape between the embosse d cavities or to the edge of the cavity whichever is less (4) This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier tape between the embossed cavity or to the edge of the cavity whichever is less (5) The embossed hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location shall be applied independent of each other (6) B dimension is a reference dimension tape feeder clearance only 1 Revision: 10-Mar-2020 5 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague CARRIER TAPE DIMENSIONS in inches [millimeters] TAPE WIDTH W D P F E E 0 2 1 2 min. 0.315 0.14 ± 0.0019 0.246 8 mm + 0.012 / - 0.004 [3.5 ± 0.05] [6.25] [8.0 + 0.3 / - 0.1] 0.078 ± 0.0019 0.479 [2.0 ± 0.05] 0.216 ± 0.0019 0.403 12 mm [1+2 0.0.0 +12 0 /.3 - /0 -. 000.41] + 0.00.0045 9/ - 0 [5.5 ± 0.05] 0.324 ± 0.004 [10.25] [1.75 ± 0.1] 0.635 [1.5 + 0.1 / - 0] 0.295 ± 0.004 0.570 16 mm + 0.012 / - 0.004 [16.0 + 0.3 / - 0.1] 0.078 ± 0.004 [7.5 ± 0.1] [14.25] [2.0 ± 0.1] 0.945 ± 0.012 0.453 ± 0.004 0.876 24 mm [24.0 ± 0.3] [11.5 ± 0.1] [22.25] CARRIER TAPE DIMENSIONS in inches [millimeters] TAPE WIDTH TYPE CASE CODE W P K B 1 0 max. 1 max. IN mm A 8 0.157 ± 0.004 0.058 [1.47] 0.149 [3.78] B 12 [4.0 ± 0.10] 0.088 [2.23] 0.166 [4.21] C 12 0.088 [2.23] 0.290 [7.36] D 12 0.315 ± 0.004 0.088 [2.23] 0.300 [7.62] 592D M 16 [8.0 ± 0.10] 0.091 [2.30] 0.311 [7.90] 592W 591D R 12 0.088 [2.23] 0.296 [7.52] S 8 0.157 ± 0.004 0.058 [1.47] 0.139 [3.53] T 12 [4.0 ± 0.10] 0.088 [2.23] 0.166 [4.21] 0.472 ± 0.004 X 24 0.011 [2.72] 0.594 [15.1] [12.0 ± 0.10] A 8 0.157 ± 0.004 0.063 [1.60] 0.152 [3.86] B 12 [4.0 ± 0.10] 0.088 [2.23] 0.166 [4.21] C 12 0.118 [2.97] 0.290 [7.36] D 12 0.315 ± 0.004 0.119 [3.02] 0.296 [7.52] G 12 [8.0 ± 0.10] 0.111 [2.83] 0.234 [5.95] 595D H 12 0.098 [2.50] 0.232 [5.90] 594D 0.157 ± 0.004 M 12 0.085 [2.15] 0.152 [3.85] [4.0 ± 0.10] 0.315 ± 0.004 R 12 0.148 [3.78] 0.296 [7.52] [8.0 ± 0.10] S 8 0.157 ± 0.004 0.058 [1.47] 0.149 [3.78] T 8 [4.0 ± 0.10] 0.054 [1.37] 0.093 [2.36] A 8 0.058 [1.47] 0.139 [3.53] B 12 0.157 ± 0.004 0.059 [1.50] 0.189 [4.80] D 12 [4.0 ± 0.10] 0.063 [1.62] 0.191 [4.85] E 12 0.074 [1.88] 0.239 [6.07] 695D 0.315 ± 0.004 F 12 0.075 [1.93] 0.259 [6.58] [8.0 ± 0.10] 0.157 ± 0.004 G 12 0.109 [2.77] 0.301 [7.65] [4.0 ± 0.10] 0.315 ± 0.004 H 16 0.124 [3.15] 0.31 [7.87] [8.0 ± 0.10] Revision: 10-Mar-2020 6 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague CARRIER TAPE DIMENSIONS in inches [millimeters] TAPE WIDTH TYPE CASE CODE W P K B 1 0 max. 1 max. IN mm A 8 0.058 [1.47] 0.139 [3.53] B 12 0.059 [1.50] 0.189 [4.80] 0.157 ± 0.004 C 8 0.054 [1.37] 0.093 [2.36] [4.0 ± 0.10] D 12 0.067 [1.70] 0.179 [4.55] E 12 0.074 [1.88] 0.239 [6.07] 0.315 ± 0.004 F 12 0.076 [1.93] 0.259 [6.58] [8.0 ± 0.10] 0.157 ± 0.004 G 12 0.109 [2.77] 0.301 [7.65] [4.0 ± 0.10] 195D 0.472 ± 0.004 H (1) 12 0.122 [3.11] 0.163 [4.14] [12.0 ± 0.1] 0.315 ± 0.004 R 12 0.149 [3.78] 0.296 [7.52] [8.0 ± 0.10] S 8 0.058 [1.47] 0.149 [3.78] V 8 0.060 [1.52] 0.150 [3.80] 0.157 ± 0.004 X 12 0.069 [1.75] 0.296 [7.52] [4.0 ± 0.10] Y 12 0.089 [2.26] 0.296 [7.52] Z 12 0.114 [2.89] 0.288 [7.31] A 8 0.058 [1.47] 0.149 [3.78] B 12 0.087 [2.20] 0.166 [4.21] P 8 0.043 [1.10] 0.102 [2.60] 0.157 ± 0.004 572D P 8 0.052 [1.32] 0.106 [2.70] [4.0 ± 0.10] Q 8 0.054 [1.37] 0.140 [3.55] S 8 0.058 [1.47] 0.149 [3.78] T 12 0.061 [1.55] 0.164 [4.16] A 8 0.069 [1.75] 0.139 [3.53] B 12 0.073 [1.85] 0.189 [4.80] 0.157 ± 0.004 194D C 12 [4.0 ± 0.10] 0.069 [1.75] 0.244 [6.20] CWR06 D 12 0.068 [1.72] 0.191 [4.85] CWR16 E 12 0.074 [1.88] 0.239 [6.07] CWR26 F 12 0.091 [2.31] 0.262 [6.65] 0.315 ± 0.004 G 16 0.134 [3.40] 0.289 [7.34] [8.0 ± 0.10] H 16 0.129 [3.28] 0.319 [8.10] D 16 0.317 ± 0.004 0.150 [3.80] 0.313 [7.95] E 16 [8.0 ± 0.10] 0.173 [4.40] 0.343 [8.70] F 16 0.205 [5.20] 0.309 [7.85] H 16 0.224 [5.70] 0.313 [7.95] 0.476 ± 0.004 597D M 16 0.193 [4.90] 0.339 [8.60] [12.0 ± 0.1] T97 N 16 0.283 [7.20] 0.323 [8.20] 13008 R 16 0.159 [4.05] 0.313 [7.95] 0.317 ± 0.004 V 12 0.088 [2.23] 0.300 [7.62] [8.0 ± 0.10] 0.476 ± 0.004 Z 16 0.239 [6.06] 0.311 [7.90] [12.0 ± 0.1] A 8 0.063 [1.60] 0.152 [3.86] 0.157 ± 0.004 B 12 0.088 [2.23] 0.166 [4.21] [4.0 ± 0.10] C 12 0.117 [2.97] 0.290 [7.36] D 12 0.317 ± 0.004 0.119 [3.02] 0.296 [7.52] R 12 [8.0 ± 0.10] 0.149 [3.78] 0.296 [7.52] T95 S 8 0.058 [1.47] 0.149 [3.78] V 8 0.060 [1.52] 0.150 [3.80] 0.157 ± 0.004 X 12 0.069 [1.75] 0.296 [7.52] [4.0 ± 0.10] Y 12 0.089 [2.26] 0.296 [7.52] Z 12 0.114 [2.89] 0.288 [7.31] B 12 0.157 ± 0.004 0.088 [2.23] 0.166 [4.21] C 12 [4.0 ± 0.10] 0.117 [2.97] 0.290 [7.36] 14002 D 12 0.317 ± 0.004 0.119 [3.02] 0.296 [7.52] R 12 [8.0 ± 0.10] 0.149 [3.78] 0.296 [7.52] 0.476 ± 0.004 T96 R 16 0.159 [4.05] 0.313 [7.95] [12.0 ± 0.1] F 16 0.239 [6.06] 0.311 [7.90] 0.476 ± 0.004 T98 M 16 0.193 [4.90] 0.339 [8.60] [12.0 ± 0.1] Z 16 0.272 [6.90] 0.307 [7.80] Note (1) H case only, packaging code T: lengthwise orientation at capacitors in tape Revision: 10-Mar-2020 7 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague PAD DIMENSIONS in inches [millimeters] B C B A CASE CODE WIDTH (A) PAD METALLIZATION (B) SEPARATION (C) 592D / W - 591D A 0.075 [1.9] 0.050 [1.3] 0.050 [1.3] B 0.118 [3.0] 0.059 [1.5] 0.059 [1.5] C 0.136 [3.5] 0.090 [2.3] 0.122 [3.1] D 0.180 [4.6] 0.090 [2.3] 0.134 [3.4] Anode pad: 0.095 [2.4] M 0.256 [6.5] 0.138 [3.5] Cathode pad: 0.067 [1.7] Anode pad: 0.095 [2.4] R 0.240 [6.1] 0.118 [3.0] Cathode pad: 0.067 [1.7] S 0.067 [1.7] 0.032 [0.8] 0.043 [1.1] X 0.310 [7.9] 0.120 [3.0] 0.360 [9.2] 595D - 594D T 0.059 [1.5] 0.028 [0.7] 0.024 [0.6] S 0.067 [1.7] 0.032 [0.8] 0.043 [1.1] A 0.083 [2.1] 0.050 [1.3] 0.050 [1.3] B 0.118 [3.0] 0.059 [1.5] 0.059 [1.5] C 0.136 [3.5] 0.090 [2.3] 0.122 [3.1] D 0.180 [4.6] 0.090 [2.3] 0.134 [3.4] G 0.156 [4.05] 0.090 [2.3] 0.082 [2.1] M 0.110 [2.8] 0.087 [2.2] 0.134 [3.4] R 0.248 [6.3] 0.090 [2.3] 0.140 [3.6] 195D A 0.067 [1.7] 0.043 [1.1] 0.028 [0.7] B 0.063 [1.6] 0.047 [1.2] 0.047 [1.2] C 0.059 [1.5] 0.031 [0.8] 0.024 [0.6] D 0.090 [2.3] 0.055 [1.4] 0.047 [1.2] E 0.090 [2.3] 0.055 [1.4] 0.079 [2.0] F 0.140 [3.6] 0.063 [1.6] 0.087 [2.2] G 0.110 [2.8] 0.059 [1.5] 0.126 [3.2] H 0.154 [3.9] 0.063 [1.6] 0.140 [3.6] N 0.244 [6.2] 0.079 [2.0] 0.118 [3.0] R 0.248 [6.3] 0.090 [2.3] 0.140 [3.6] S 0.079 [2.0] 0.039 [1.0] 0.039 [1.0] V 0.114 [2.9] 0.039 [1.0] 0.039 [1.0] X 0.118 [3.0] 0.067 [1.7] 0.122 [3.1] Y 0.118 [3.0] 0.067 [1.7] 0.122 [3.1] Z 0.118 [3.0] 0.067 [1.7] 0.122 [3.1] Revision: 10-Mar-2020 8 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague PAD DIMENSIONS in inches [millimeters] B C B A CASE CODE WIDTH (A) PAD METALLIZATION (B) SEPARATION (C) CWR06 / CWR16 / CWR26 - 194D - 695D A 0.065 [1.6] 0.50 [1.3] 0.040 [1.0] B 0.065 [1.6] 0.70 [1.8] 0.055 [1.4] C 0.065 [1.6] 0.70 [1.8] 0.120 [3.0] D 0.115 [2.9] 0.70 [1.8] 0.070 [1.8] E 0.115 [2.9] 0.70 [1.8] 0.120 [3.0] F 0.150 [3.8] 0.70 [1.8] 0.140 [3.6] G 0.125 [3.2] 0.70 [1.8] 0.170 [4.3] H 0.165 [4.2] 0.90 [2.3] 0.170 [4.3] T95 B 0.120 [3.0] 0.059 [1.5] 0.059 [1.5] C 0.136 [3.5] 0.090 [2.3] 0.120 [3.1] D 0.180 [4.6] 0.090 [2.3] 0.136 [3.47] R 0.248 [6.3] 0.090 [2.3] 0.140 [3.6] S 0.080 [2.03] 0.040 [1.02] 0.040 [1.02] V 0.114 [2.9] 0.040 [1.02] 0.040 [1.02] X, Y, Z 0.114 [2.9] 0.065 [1.65] 0.122 [3.1] 14002 B 0.120 [3.0] 0.059 [1.5] 0.059 [1.5] C 0.136 [3.5] 0.090 [2.3] 0.120 [3.1] D 0.180 [4.6] 0.090 [2.3] 0.136 [3.47] R 0.248 [6.3] 0.090 [2.3] 0.140 [3.6] T96 R 0.248 [6.3] 0.090 [2.3] 0.140 [3.6] 597D - T97 - T98 - 13008 D, E, V 0.196 [4.9] 0.090 [2.3] 0.140 [3.6] F, R, Z 0.260 [6.6] 0.090 [2.3] 0.140 [3.6] M, H, N 0.284 [7.2] 0.090 [2.3] 0.140 [3.6] PAD DIMENSIONS in inches [millimeters] B C B 1 A CASE CODE WIDTH (A) PAD METALLIZATION (B) PAD METALLIZATION (B ) SEPARATION (C) 1 572D A 0.079 [2.0] 0.039 [1.0] 0.035 [0.9] 0.047 [1.2] Q 0.079 [2.0] 0.039 [1.0] 0.035 [0.9] 0.047 [1.2] S 0.079 [2.0] 0.039 [1.0] 0.035 [0.9] 0.047 [1.2] B 0.110 [2.8] 0.039 [1.0] 0.035 [0.9] 0.055 [1.4] P 0.055 [1.4] 0.024 [0.6] 0.024 [0.6] 0.035 [0.9] T 0.110 [2.8] 0.035 [0.9] 0.031 [0.8] 0.055 [1.4] Revision: 10-Mar-2020 9 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague RECOMMENDED REFLOW PROFILES Capacitors should withstand reflow profile as per J-STD-020 standard, three cycles. T p T - 5 °C Max. ramp-up rate = 3 °C/s tp C Max. ramp-down rate = 6 °C/s C) T RE (° L Ts max. Preheat area tL U T A R T E s min. P M TE ts 25 Time 25 °C to peak TIME (s) PROFILE FEATURE SnPb EUTECTIC ASSEMBLY LEAD (Pb)-FREE ASSEMBLY Preheat / soak Temperature min. (T ) 100 °C 150 °C s min. Temperature max. (T ) 150 °C 200 °C s max. Time (t) from (T to T ) 60 s to 120 s 60 s to 120 s s smin. s max. Ramp-up Ramp-up rate (T to T ) 3 °C/s max. 3 °C/s max. L p Liquidus temperature (T ) 183 °C 217 °C L Time (t ) maintained above T 60 s to 150 s 60 s to 150 s L L Peak package body temperature (T ) Depends on type and case – see table below p Time (tp)* within 5 °C of the specified 20 s 30 s classification temperature (T ) c Ramp-down Ramp-down rate (T to T ) 6 °C/s max. 6 °C/s max. p L Time 25 °C to peak temperature 6 min max. 8 min max. PEAK PACKAGE BODY TEMPERATURE (T ) p PEAK PACKAGE BODY TEMPERATURE (T ) p TYPE / CASE CODE SnPb EUTECTIC PROCESS LEAD (Pb)-FREE PROCESS 591D / 592D - all cases, except X25H, M and R cases 235 °C 260 °C 591D / 592D - X25H, M and R cases 220 °C 250 °C 594D / 595D - all cases except C, D, and R 235 °C 260 °C 594D / 595D - C, D, and R case 220 °C 250 °C 572D all cases n/a 260 °C T95 A, B, S, V, X, Y cases 235 °C 260 °C T95 C, D, R, and Z cases 220 °C 250 °C 14002 B case 235 °C n/a 14002 C, D, and R cases 220 °C n/a T96 R case 220 °C 250 °C 195D all cases, except G, H, R, and Z 235 °C 260 °C 195D G, H, R, and Z cases 220 °C 250 °C 695D all cases, except G and H cases 235 °C 260 °C 695D G, H cases 220 °C 250 °C 597D, T97, T98 all cases, except V case 220 °C 250 °C 597D, T97, T98 V case 235 °C 260 °C 194D all cases, except H and G cases 235 °C 260 °C 194D H and G cases 220 °C 250 °C Revision: 10-Mar-2020 10 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague GUIDE TO APPLICATION 1. AC Ripple Current: the maximum allowable rippl e 5. Power Dissipation: power dissipation will b e current shall be determined from the formula: affected by the heat sinking capability of th e mounting surface. Non-sinusoidal ripple current ma y P I = ------------ produce heating effects which differ from those RMS RESR shown. It is important that the equivalent IRMS value be established when calculating permissible where, operating levels. (Power dissipation calculated using P = power dissipation in W at +25 °C as given i n derating factor (see paragraph 4)). the tables in the product datasheets (Power Dissipation). 6. Attachment: 6.1 Soldering: capacitors can be attached b y R = the capacitor equivalent series resistance at ESR conventional soldering techniques: vapor phase, the specified frequency convection reflow, infrared reflow, and hot plate methods. The soldering profile charts show 2. AC Ripple Voltage: the maximum allowable ripple recommended time / temperature conditions fo r voltage shall be determined from the formula: soldering. Preheating is recommended. The VRMS = IRMS x Z recommended maximum ramp rate is 2 °C pe r or, from the formula: second. Attachment with a soldering iron is not recommended due to the difficulty of controllin g P temperature and time at temperature. The solderin g V = Z ------------ RMS R iron must never come in contact with the capacitor . ESR For details see www.vishay.com/doc?40214. where, 7. Recommended Mounting Pad Geometries: the ni b P = power dissipation in W at +25 °C as given i n must have sufficient clearance to avoid electrical the tables in the product datasheets (Power contact with other components. The width Dissipation). dimension indicated is the same as the maximum width of the capacitor. This is to minimize lateral R = the capacitor equivalent series resistance at ESR movement. the specified frequency Z = the capacitor impedance at the specified 8. Cleaning (Flux Removal) After Soldering: frequency TANTAMOUNT™ capacitors are compatible with all commonly used solvents such as TES, TMS, Prelete, 2.1 The sum of the peak AC voltage plus the applied DC Chlorethane, Terpene and aqueous cleaning media . voltage shall not exceed the DC voltage rating of the However, CFC / ODS products are not used in the capacitor. production of these devices and are not recommended. Solvents containing methylene 2.2 The sum of the negative peak AC voltage plu s chloride or other epoxy solvents should be avoide d the applied DC voltage shall not allow a voltage since these will attack the epoxy encapsulation reversal exceeding 10 % of the DC working voltage material. at +25 °C. 3. Reverse Voltage: solid tantalum capacitors are not intended for use with reverse voltage applied . However, they have been shown to be capable o f withstanding momentary reverse voltage peaks of u p to 10 % of the DC rating at 25 °C and 5 % of the DC rating at +85 °C. 4. Temperature Derating: if these capacitors are to be operated at temperatures above +25 °C, the permissible RMS ripple current shall be calculated using the derating factors as shown: TEMPERATURE DERATING FACTOR +25 °C 1.0 +85 °C 0.9 +125 °C 0.4 Revision: 10-Mar-2020 11 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Typical Performance Characteristics www.vishay.com Vishay Sprague Conformal Coated Tantalum Capacitors ELECTRICAL PERFORMANCE CHARACTERISTICS ITEM PERFORMANCE CHARACTERISTICS Category temperature range -55 °C to +85 °C (to +125 °C with voltage derating) Capacitance tolerance ± 20 %, ± 10 %, tested via bridge method, at 25 °C, 120 Hz Dissipation factor Limits per Standard Ratings table. Tested via bridge method, at 25 °C, 120 Hz ESR Limits per Standard Ratings table. Tested via bridge method, at 25 °C, 100 kHz Leakage current After application of rated voltage applied to capacitors for 5 min using a steady source of power with 1 kΩ resistor in series with the capacitor under test, leakage current at 25 °C is not more than 0.01 CV or 0.5 μA, whichever is greater. Note that the leakage current varies with temperature and applied voltage. See graph below for the appropriate adjustment factor. Capacitance change by For capacitance value ≤ 300 μF For capacitance value > 300 μF temperature +12 % max. (at +125 °C) +20 % max. (at +125 °C) +10 % max. (at +85 °C) +15 % max. (at +85 °C) -10 % max. (at -55 °C) -15 % max. (at -55 °C) Reverse voltage Capacitors are capable of withstanding peak voltages in the reverse direction equal to: 10 % of the DC rating at +25 °C 5 % of the DC rating at +85 °C 1 % of the DC rating at +125 °C Vishay does not recommend intentional or repetitive application of reverse voltage. Ripple current For maximum ripple current values (at 25 °C) refer to relevant datasheet. If capacitors are to be used at temperatures above +25 °C, the permissible RMS ripple current (or voltage) shall be calculated using the derating factors: 1.0 at +25 °C 0.9 at +85 °C 0.4 at +125 °C Maximum operating and surge +85 °C +125 °C voltages vs. temperature RATED VOLTAGE SURGE VOLTAGE CATEGORY VOLTAGE SURGE VOLTAGE (V) (V) (V) (V) 2.0 2.7 1.3 1.7 4.0 5.2 2.7 3.4 6.3 8.0 4.0 5.0 10 13 7.0 8.0 15 / 16 20 10 12 20 26 13 16 25 32 17 20 35 46 23 28 40 52 26 31 50 65 33 40 50 (1) 60 33 40 63 (2) 75 42 50 75 (2) 75 50 50 Recommended voltage VOLTAGE RAIL CAPACITOR VOLTAGE RATING derating guidelines ≤ 3.3 6.3 (below 85 °C) 5 10 10 20 12 25 15 35 ≥ 24 50 or series configuration Notes • All information presented in this document reflects typical performance characteristics (1) Capacitance value 15 μF and higher (2) For 597D only Revision: 21-Jun-17 1 Document Number: 40194 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Typical Performance Characteristics www.vishay.com Vishay Sprague TYPICAL LEAKAGE CURRENT TEMPERATURE FACTOR 100 +125 °C +85 °C ctor 10 +55 °C a nt F 1.0 +25 °C urre 0 °C C e 0.1 g a -55 °C k a e L 0.01 0.001 0 10 20 30 40 50 60 70 80 90 100 Percent of Rated Voltage Notes • At +25 °C, the leakage current shall not exceed the value listed in the Standard Ratings table • At +85 °C, the leakage current shall not exceed 10 times the value listed in the Standard Ratings table • At +125 °C, the leakage current shall not exceed 12 times the value listed in the Standard Ratings table ENVIRONMENTAL PERFORMANCE CHARACTERISTICS ITEM CONDITION POST TEST PERFORMANCE Surge voltage Post application of surge voltage (as specified Capacitance change Within ± 10 % of initial value in the table above) in series with a 33 Ω resistor Dissipation factor Initial specified limit at the rate of 30 s ON, 30 s OFF, for 1000 Leakage current Initial specified limit successive test cycles at 85 °C MIL-PRF-55365 Life test at +85 °C 2000 h application of rated voltage at 85 °C Capacitance change Within ± 10 % of initial value MIL-STD-202, method 108 Dissipation factor Initial specified limit Leakage current Shall not exceed 125 % of initial limit Life test at +125 °C 1000 h application 2/3 of rated voltage at 125 °C Capacitance change: MIL-STD-202, method 108 Cap. ≤ 600 μF Within ± 10 % of initial value Cap. > 600 μF Within ± 20 % of initial value Dissipation factor Initial specified limit Leakage current Shall not exceed 125 % of initial limit Humidity test At 40 °C / 90 % RH, 1000 h, no voltage applied Capacitance change: MIL-STD-202, method 103 Cap. ≤ 600 μF Within ± 10 % of initial value Cap. > 600 μF Within ± 20 % of initial value Dissipation factor Not to exceed 150 % of initial limit Leakage current Shall not exceed 200 % of initial limit Moisture resistance MIL-STD-202, method 106 at rated voltage, Capacitance change: 20 cycles Cap. ≤ 600 μF Within ± 15 % of initial value Cap. > 600 μF Within ± 20 % of initial value Dissipation factor Shall not exceed 150 % of initial limit Leakage current Shall not exceed 200 % of initial limit Thermal shock At -55 °C / +125 °C, for 5 cycles, Capacitance change: 30 min at each temperature Cap. ≤ 600 μF Within ± 10 % of initial value MIL-STD-202, method 107 Cap. > 600 μF Within ± 20 % of initial value Dissipation factor Initial specified limit Leakage current Initial specified limit Revision: 21-Jun-17 2 Document Number: 40194 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Typical Performance Characteristics www.vishay.com Vishay Sprague MECHANICAL PERFORMANCE CHARACTERISTICS ITEM CONDITION POST TEST PERFORMANCE Terminal strength / Apply a pressure load of 5 N for 10 s ± 1 s horizontally Capacitance change Within ± 10 % of initial value Shear force test to the center of capacitor side body AEC-Q200-006 Dissipation factor Initial specified limit Leakage current Initial specified limit There shall be no mechanical or visual damage to capacitors post-conditioning. Vibration MIL-STD-202, method 204, condition D, Electrical measurements are not applicable, since the 10 Hz to 2000 Hz, 20 g peak, 8 h, at rated voltage same parts are used for shock (specified pulse) test. There shall be no mechanical or visual damage to capacitors post-conditioning. Shock MIL-STD-202, method 213, condition I, Capacitance change: (specified pulse) 100 g peak Cap. ≤ 600 μF Within ± 10 % of initial value Cap. > 600 μF Within ± 20 % of initial value Dissipation factor Initial specified limit Leakage current Initial specified limit There shall be no mechanical or visual damage to capacitors post-conditioning. Resistance MIL-STD-202, method 210, condition J Capacitance change Within ± 10 % of initial value to solder heat (SnPb terminations) and K (lead (Pb)-free terminations), Dissipation factor Initial specified limit one heat cycle Leakage current Initial specified limit Solderability EIA / IPC / JEDEC J-STD-002 Solder coating of all capacitors shall meet specified Test B (SnPb) and B1 (lead (Pb)-free). requirements. Preconditioning per category C. There shall be no mechanical or visual damage to Capacitors with SnPb and lead (Pb)-free terminations capacitors post-conditioning. are backward and forward compatible. Does not apply to gold terminations. Flammability Encapsulation materials meet UL 94 V-0 with an oxygen index of 32 % Revision: 21-Jun-17 3 Document Number: 40194 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROV E RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose o r the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustainin g applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk . Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this documen t or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2019 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2019 1 Document Number: 91000