TVS Diode Axial Leaded – 30000W > 30KPA series 30KPA Series RoHS Pb e3 Descriptions Uni-directional The 30KPA Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Bi-directional • 30kW peak pulse • Low incremental surge capability at 10/1000μs resistance waveform, repetition rate • Typical I less than 2μA R (duty cycles):0.01% when V min>73V BR • Glass passivated chip • High temperature Agency Approvals junction in P600 package to reflow soldering • Fast response time: guaranteed: 260°C/40sec Agency Agency File Number typically less than 1.0ps / 0.375”, (9.5mm) lead from 0 Volts to BV min length, 5 lbs., (2.3kg) E230531 • Excellent clamping tension capability • V @ T= V @25°C BR J BR • Typical failure mode is x (1+αT x (T - 25)) Maximum Ratings and Thermal Characteristics J short from over-specified (αT:Temperature (T =25OC unless otherwise noted) A voltage or current Coefficient, typical value is 0.1%) • Whisker test is conducted Parameter Symbol Value Unit based on JEDEC • UL Recognized epoxy Peak Pulse Power Dissipation by 10/1000μs Test JESD201A per its table 4a meeting flammability P 30 kW Waveform (Fig.2)(Note 1) PPM and 4c rating V-0 Steady State Power Dissipation on Infinite Heat P 8.0 W • IEC-61000-4-2 ESD • Matte tin lead–free plated Sink at T=75ºC D L 30kV(Air), 30kV (Contact) • Halogen free and RoHS Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional Only (Note 2) IFSM 400 A • ESD protection of data compliant Operating Junction and Storage Temperature lines in accordance with • Pb-free E3 means 2nd T, T -55 to 175 °C Range J STG IEC 61000-4-2 level interconnect is Pb- Typical Thermal Resistance Junction to Lead RθJL 8.0 °C/W • EFT protection of data free and the terminal finish Typical Thermal Resistance Junction to Ambient R 40 °C/W lines in accordance with material is tin(Sn) (IPC/ θJA IEC 61000-4-4 JEDEC J-STD-609A.01) Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above T (initial) =25OC per Fig. 3. J 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum. Applications TVS components are ideal for the protection of I/O interfaces, V bus and other vulnerable circuits used in CC telecom, computer, industrial and consumer electronic applications. Functional Diagram Additional Infomarion Datasheet Resources Samples Bi-directional Cathode Anode Uni-directional © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/27/20

TVS Diode Axial Leaded – 30000W > 30KPA series Electrical Characteristics (T=25°C unless otherwise noted) A Breakdown Test Maximum Maximum Agency Nu(PUmanrbit) e r NuP(mBarib)t e r Roeffv eV(Vorsoltelat sgS)eta VnRd V(Vooltlatsg)e @ V BITR CurIrTe nt MPauxlsiIme uC (muAr )rPeenatk LReeavkeargsee CVlaomltapgineg Recognition (mA) pp I @V (µ A) V @ I (V) Min. Max. R R C PP 30KPA28A 30KPA28CA 28 31.28 34.41 50 606.0 5000 50.0 X 30KPA30A 30KPA30CA 30 33.51 36.86 50 548.9 5000 55.2 X 30KPA33A 30KPA33CA 33 36.90 40.59 50 517.9 5000 58.5 X 30KPA36A 30KPA36CA 36 40.20 44.22 50 490.3 5000 61.8 X 30KPA39A 30KPA39CA 39 43.60 47.96 20 450.9 2000 67.2 X 30KPA42A 30KPA42CA 42 46.90 51.59 10 420.8 1000 72.0 X 30KPA43A 30KPA43CA 43 48.00 52.80 10 415.1 1000 73.0 X 30KPA45A 30KPA45CA 45 50.30 55.33 5 391.5 250 77.4 X 30KPA48A 30KPA48CA 48 53.60 58.96 5 371.3 150 81.6 X 30KPA51A 30KPA51CA 51 57.00 62.70 5 350.7 50 86.4 X 30KPA54A 30KPA54CA 54 60.30 66.33 5 331.5 20 91.4 X 30KPA58A 30KPA58CA 58 64.80 71.28 5 327.9 20 92.4 X 30KPA60A 30KPA60CA 60 67.00 73.70 5 297.1 15 102.0 X 30KPA64A 30KPA64CA 64 71.50 78.65 5 291.3 10 104.0 X 30KPA66A 30KPA66CA 66 73.70 81.07 5 283.2 2 107.0 X 30KPA70A 30KPA70CA 70 78.20 86.02 5 278.0 2 109.0 X 30KPA71A 30KPA71CA 71 79.30 87.23 5 271.7 2 111.5 X 30KPA72A 30KPA72CA 72 80.40 88.44 5 265.8 2 114.0 X 30KPA75A 30KPA75CA 75 83.80 92.18 5 253.8 2 119.4 X 30KPA78A 30KPA78CA 78 87.10 95.81 5 234.9 2 129.0 X 30KPA84A 30KPA84CA 84 93.80 103.18 5 217.7 2 139.2 X 30KPA90A 30KPA90CA 90 100.50 110.55 5 207.0 2 146.4 X 30KPA96A 30KPA96CA 96 107.20 117.92 5 194.2 2 156.0 X 30KPA102A 30KPA102CA 102 113.90 125.29 5 183.0 2 165.6 X 30KPA108A 30KPA108CA 108 120.60 132.66 5 172.9 2 175.2 X 30KPA120A 30KPA120CA 120 134.00 147.40 5 155.9 2 194.4 X 30KPA132A 30KPA132CA 132 147.40 162.14 5 142.3 2 213.0 X 30KPA144A 30KPA144CA 144 160.80 176.88 5 135.8 2 223.2 X 30KPA150A 30KPA150CA 150 167.60 184.36 5 129.8 2 233.4 X 30KPA156A 30KPA156CA 156 174.30 191.73 5 123.7 2 245.0 X 30KPA160A 30KPA160CA 160 178.70 196.57 5 120.0 2 252.6 X 30KPA168A 30KPA168CA 168 187.70 206.47 5 111.2 2 272.4 X 30KPA170A 30KPA170CA 170 189.90 208.89 5 110.2 2 275.0 X 30KPA180A 30KPA180CA 180 201.10 221.21 5 104.3 2 290.4 X 30KPA198A 30KPA198CA 198 221.20 243.32 5 94.7 2 319.8 X 30KPA216A 30KPA216CA 216 241.30 265.43 5 86.9 2 348.6 X 30KPA240A 30KPA240CA 240 268.10 294.91 5 78.3 2 387.0 X 30KPA258A 30KPA258CA 258 288.20 317.02 5 72.8 2 416.4 X 30KPA260A 30KPA260CA 260 290.40 319.44 5 72.8 2 416.0 X 30KPA270A 30KPA270CA 270 301.60 331.76 5 69.5 2 436.2 X 30KPA280A 30KPA280CA 280 312.80 344.08 5 65.3 2 464.0 X 30KPA288A 30KPA288CA 288 321.70 353.87 5 64.5 2 469.9 X 30KPA300A 30KPA300CA 300 334.00 367.40 5 62.0 2 484.0 X 30KPA320A 30KPA320CA 320 357.40 391.40 5 57.2 2 530.0 - 30KPA350A 30KPA350CA 350 391.00 428.10 5 53.4 2 567.0 - 30KPA360A 30KPA360CA 360 402.10 440.30 5 47.3 2 640.0 - For bidirectional type having V of 60 volts and less, the I limit is double. RWM R For parts without A , the V is ± 10% and Vc is 5% higher than with A parts, the parts without A are currently available, but not recommended for new designs. The parts with A are preferred. BR © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/27/20

TVS Diode Axial Leaded – 30000W > 30KPA series I-V Curve Characteristics Uni-directional Bi-directional Ipp IT Vc VBRVR V Vc VBRVR IR V IRVF IR VRVBRVc IT IT Ipp Ipp P Peak Pulse Power Dissipation -- Max power dissipation PPM V Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation R V Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (I) BR T V Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) C I Reverse Leakage Current -- Current measured at V R R V Forward Voltage Drop for Uni-directional F Ratings and Characteristic Curves (T=25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Curve 1000 Voltage Transients W) k Voltage Across TVS wer ( 100 nt Po age or Curre Current Through TVS Peak Pulse 10 Volt P-PPM 1 0.000001 0.00001 0.0001 0.001 t-Pulse Width (sec.) d Time © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/27/20

TVS Diode Axial Leaded – 30000W > 30KPA series Ratings and Characteristic Curves (T=25°C unless otherwise noted) (Continued) A Figure 3 - Peak Pulse Power Derating Curve Figure 4 - Pulse Waveform 150 100 k Pulse Power (P) or Current (I)PPPPDerating in Percentage % 257505 I- Peak Pulse Current, % IPPMRSM 15000 tr=1PI0PeµPasMke cVaHIlPuaPelMf Va(lI Pu P1a2eTPac0sM usuJ / rd1=)ltrsh02eeee50nfi W °0tpnC dµioedeisdtnceh tabc( wyt.yds hW ) R teiosar. E ev5d .0eteAh%ffieon orpemfde IaPkP M a Pe 0 td 0 25 50 75 100 125 150 175 200 0 0 1.0 2.0 3.0 4.0 TJ - Initial Junction Temperature (ºC) t-Time (ms) Figure 5 - Typical Junction Capacitance Figure 6 - Typical Transient Thermal Impedance 10000 100 Uni-direc(cid:31)onal V=0V Bi-direc(cid:31)onal V=0V W) C/ 1000 e (° c an 10 F) Uni-direc(cid:31)onal V=VR ped p m Cj ( 100 Bi-direc(cid:31)onal V=V mal I R er Th 1 nt 10 sie n a Tr 0.1 1 0 50 100 150 200 250 300 350 400 0.01 0.1 1 10 100 1000 VBR - Reverse Breakdown Voltage (V) TP-Pulse Duration (s) Figure 7 - Maximum Non-Repetitive Peak Forward Figure 8 - Peak Forward Voltage Drop vs Peak Forward Surge Current Uni-Directional Only Current (Typical Values) 1000 nt (A) 900 100 4 stacked-die e Curr 800 A) d Surge 670000 Current( 10 5 stacked-die ar d orw 500 war k F 400 For Pea- 300 Peak 1 FSM 200 I-F I 100 0 0.1 1 10 100 0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 Number of Cycles at 60 Hz VF-Peak Forward Voltage(V) © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/27/20

TVS Diode Axial Leaded – 30000W > 30KPA series Soldering Parameters Reflow Condition Lead–free assembly - Temperature Min (Ts(min)) 150°C TP tp Pre Heat - Temperature Max (T ) 200°C Ramp-up Critical Zone - Time (min to max) (tss(m)ax) 60 – 180 secs TL tL TL to TP Average ramp up rate (Liquidus Temp (TA) to peak 3°C/second max e (T)Ts(max) RTSe(mflaox)w to TA - R-a Tmemp-puepr Ratautree (TA) (Liquidus) 231°C7°/sCe cond max emperaturTTs(min) Prethseat Ramp-down - Time (min to max) (t) 60 – 150 seconds s Peak Temperature (TP) 260+0/-5 °C 25˚C t 25˚C to Peak Time within 5°C of actual peak Temperature (t) 20 – 40 seconds Time (t) p Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (T) 8 minutes Max. P Do not exceed 260°C Flow/Wave Soldering (Solder Dipping) Peak Temperature : 265OC Dipping Time : 10 seconds Soldering : 1 time Physical Specifications Environmental Specifications Weight 0.07oz., 2.5g High Temp. Storage JESD22-A103 Case P600 molded plastic body over passivated junction. HTRB JESD22-A108 Polarity Color band denotes the cathode except Bipolar. Temperature Cycling JESD22-A104 Matte Tin axial leads, solderable per H3TRB JESD22-A101 Terminal JESD22-B102. RSH JESD22-B106 Dimensions Inches Millimeters Cathode Band Dimensions D (for uni-directional products only) Min Max Min Max A 1.000 - 25.40 - C B 0.340 0.360 8.60 9.10 C 0.048 0.054 1.22 1.36 A B A D 0.340 0.360 8.60 9.10 P600 © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/27/20

TVS Diode Axial Leaded – 30000W > 30KPA series Part Numbering System Part Marking System 30KPA xxxXX X Cathode Band (for uni-directional Option Code: products only) Blank Reel Tape F YYWW -B Bulk Packaging Littelfuse Logo Trace Code Marking Type Code: YY:Year Code A Uni-Directional (5% V Voltage Tolerance) WW: Week Code BR CA Bi-Directional (5% V Voltage Tolerance) BR 30KPAXXX Product Type VVoltage R Series Code Packing Options Part Number Component Package Quantity Packaging Option Packaging Specification 30KPAxxxXX P600 800 Tape & Reel EIA STD RS-296 30KPAxxxXX-B P600 100 Bulk Littelfuse Spec. Tape and Reel Specification Off Center (625.5.06) e0.i0th28e(r0 s.7id)e 2.0(6533+.00+.027.09//--10..00)39 0.047 0.236 (1.2) (6.0) 0.394+/-0.020 (10.0+/-0.5) Dimensions are in 13.0 inches/mm (330.2) 3.0 (76.2) 0.68 (17.27) 2.75 (69.85) Direction of Feed Recess Depth Max. 0.75 (19.05) Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/27/20