FL SWITCH SFNT… Five and Eight-Port Standard Function Ethernet Switches for Extreme Environments AUTOMATION Data Sheet 2665_en_I © PHOENIX CONTACT 2011-06-30 1 Description 2 Features and Benefits The FL SWITCH SFNT… range of Factory Line switches – -40 to 75°C operating range can be used for quick and cost-effective Ethernet network – Pretagged high priority messages are forwarded before expansion to the field level. These unmanaged switches lower priority messages during periods of high network allow operation across a wider temperature range than most traffic switches, allowing networks to expand into process industry – Auto-negotiation and autocross simplify cabling environments, such as oil/gas, chemical, water/wastewater, – Couple copper network segments with different bit rates wind energy, security, monitoring and some marine with automatic detection of the data transmission speed segments. Due to the narrow housing design, the switches of 10 or 100 Mbps are suitable for use in control cabinets and junction boxes. – Individual LEDs at each port indicate communication The FL SWITCH SFNT… switches support the auto activity and data rate negotiation function on the RJ45 ports and offer – Redundant power supply capable with local (LED) and transmission speeds of 10/100Mbps. Mixed operation for remote (dry contact) alarms to indicate failure of one or the connection of segments with different data transmission both power supplies speeds is also supported. The RJ45 ports offer an auto crossing function, which means it is not necessary to make – Switch-selectable link diagnostics indicate a distinction between 1:1 and crossover cables. Unused disconnected ports via local and remote alarms RJ45 ports can be fitted with security caps to provide – Available fiber optic options for extended distance and mechanical protection against unauthorized use. electrical noise immunity Fiber optic ports are available in an SC or ST format and – Fiber optic ports available in SC or ST formats offer speeds of 100 Mbps. The fiber optic ports extend the – Low-cost, low-complexity security by connecting segment length to 2000 m or more, depending on the quality Layer1 security elements at the RJ45 ports to restrict of the fiber optic cable. access and tampering (optional) Please note the different connection directions of the transmission media for five-port switches: copper cables are connected at the front, glass fiber cables at the bottom. This data sheet is valid for all products listed on the following page: Make sure you always use the latest documentation. It can be downloaded at www.phoenixcontact.net/catalog.

FL SWITCH SFNT… 3 Ordering Data Description Type Order No. Pcs./Pkt. Ethernet switch, wide temperature with 5 RJ45 ports for 10/100 Mbps FL SWITCH SFNT 5TX 2891003 1 Ethernet switch, wide temperature with 8 RJ45 ports for 10/100 Mbps FL SWITCH SFNT 8TX 2891005 1 Ethernet switch, wide temperature with 4 RJ45 ports and 1 fiber optic FL SWITCH SFNT 4TX/FX 2891004 1 port in SC format, for 10/100 Mbps Ethernet switch, wide temperature with 7 RJ45 ports and 1 fiber optic FL SWITCH SFNT 7TX/FX 2891006 1 port in SC format, for 10/100 Mbps Ethernet switch, wide temperature with 7 RJ45 ports and 1 fiber optic FL SWITCH SFNT 7TX/FX ST 2891007 1 port in ST format, for 10/100 Mbps Ethernet switch, wide temperature with 6 RJ45 ports and 2 fiber optic FL SWITCH SFNT 6TX/2FX 2891025 1 ports in SC format, for 10/100 Mbps Ethernet switch, wide temperature with 6 RJ45 ports and 2 fiber optic FL SWITCH SFNT 6TX/2FX ST 2891026 1 ports in ST format, for 10/100 Mbps Ethernet switch, wide temperature with 5 RJ45 ports for 10/100 Mbps, FL SWITCH SFNT 5TX-C 2891043 1 with conformal coating Ethernet switch, wide temperature with 8 RJ45 ports for 10/100 Mbps, FL SWITCH SFNT 8TX-C 2891044 1 with conformal coating Ethernet switch, wide temperature with 4 RJ45 ports and 1 fiber optic FL SWITCH SFNT 4TX/FX-C 2891045 1 port in SC format, for 10/100 Mbps, with conformal coating Ethernet switch, wide temperature with 7 RJ45 ports and 1 fiber optic FL SWITCH SFNT 7TX/FX-C 2891046 1 port in SC format, for 10/100 Mbps, with conformal coating Ethernet switch, wide temperature with 7 RJ45 ports and 1 fiber optic FL SWITCH SFNT 7TX/FX ST-C 2891047 1 port in ST format, for 10/100 Mbps, with conformal coating Ethernet switch, wide temperature with 6 RJ45 ports and 2 fiber optic FL SWITCH SFNT 6TX/2FX-C 2891048 1 ports in SC format, for 10/100 Mbps, with conformal coating Ethernet switch, wide temperature with 6 RJ45 ports and 2 fiber optic FL SWITCH SFNT 6TX/2FX ST-C 2891049 1 ports in ST format, for 10/100 Mbps, with conformal coating Accessories Description Type Order No. Pcs./Pkt. Universal end clamp E/NS 35 N 0800886 50 Patch angle with 2 ports in CAT 5e FL PF 2TX CAT5E 2891165 1 Patch angle with 8 ports in CAT 5e FL PF 8TX CAT5E 2891178 1 Patch angle with 2 ports in CAT 6 FL PF 2TX CAT6 2891068 1 Patch angle with 8 ports in CAT 6 FL PF 8TX CAT6 2891071 1 Patch angle with security elements for 2 ports in CAT 5e FL PF SEC 2TX 2832687 1 Patch angle with security elements for 8 ports in CAT 5e FL PF SEC 8TX 2832690 1 Patchbox 8 x RJ45 CAT 5e, pre-assembled, can be retrofitted FL PBX 8TX 2832496 1 Patch cable, CAT 5, pre-assembled, 0.3 m long FL CAT5 PATCH 0,3 2832250 10 Patch cable, CAT 5, pre-assembled, 0.5 m long FL CAT5 PATCH 0,5 2832263 10 Patch cable, CAT 5, pre-assembled, 1.0 m long FL CAT5 PATCH 1,0 2832276 10 Patch cable, CAT 5, pre-assembled, 1.5 m long FL CAT5 PATCH 1,5 2832221 10 Patch cable, CAT 5, pre-assembled, 2.0 m long FL CAT5 PATCH 2,0 2832289 10 Patch cable, CAT 5, pre-assembled, 3.0 m long FL CAT5 PATCH 3,0 2832292 10 Patch cable, CAT 5, pre-assembled, 5.0 m long FL CAT5 PATCH 5,0 2832580 10 Patch cable, CAT 5, pre-assembled, 7.5 m long FL CAT5 PATCH 7,5 2832616 10 Patch cable, CAT 5, pre-assembled, 10.0 m long FL CAT5 PATCH 10 2832629 10 Security frame for SFN switch and patch fields, green FL PLUG GUARD, GN 2891615 20 Security frame for SFN switch and patch fields, red FL PLUG GUARD, RD 2891712 20 Security frame for SFN switch and patch fields, white FL PLUG GUARD, WH 2891819 20 Security frame for SFN switch and patch fields FL PORT GUARD 2891220 20 Security frame for SFN switch and patch fields FL PLUG GUARD KEY 2891327 1 Security element for FL CAT patch FL PATCH SAFE CLIP 2891246 20 Mounting plate for SFNT… 5 and 8 port switches FL PA SFNT 5-8 2891012 1 Mounting plate, DIN rail, for SFNT… 5 and 8 port switches FL DA SFNT 5-8 2891017 1 2665_en_I PHOENIX CONTACT 2

FL SWITCH SFNT… 4 Technical Data General Data Function Switch/repeater; conforms to standard IEEE802.3 Latency of the communication processor 8µs plus frame time Housing dimensions (width x height x depth) 5-port switch, without connectors 30 x 130 x 100 mm 8-port switch, without connectors 50 x 130 x 100 mm Weight, without connectors FL SWITCH SFNT 5TX(-C) 271 g FL SWITCH SFNT 8TX(-C) 457 g FL SWITCH SFNT 4TX/FX(-C) 276 g FL SWITCH SFNT 7TX/FX(-C) 464 g FL SWITCH SFNT 7TX/FX ST(-C) 465 g FL SWITCH SFNT 6TX/2FX(-C) 484 g FL SWITCH SFNT 6TX/2FX ST (-C) 484 g Operating temperature -40°C to 75°C Storage temperature -40°C to 85°C Degree of protection IP20, DIN 40050, IEC 60529 Protection class Class 3 VDE 0106; IEC 60536 Humidity (operation and storage) 5% to 95%, no condensation Air pressure (operation) 62 kPa to 108 kPa, 4160 m above sea level Air pressure (storage) 62 kPa to 108 kPa, 4160 m above sea level Mounting NS 35 (EN 60715) Preferred mounting position Perpendicular to a standard mounting rail Connection to protective earth ground Snapped onto a grounded mounting rail Supply Voltage (US) Connection type Removable, screw-clamp connector Wire size (solid/stranded/AWG) 0.2 to 2.5 mm² / 0.2 to 2.5 mm² / 24 to 12 AWG Recommended PE wire size 2.5 mm2 Nominal power supply 24 V DC Permissible ripple 3.6 V within the permissible voltage range pp Permissible voltage range 9VDC to 32VDC Test voltage 500 V DC for one minute Protection against polarity reversal Present Current Consumption and Inrush Current Current Consumption (max) @ 24VDC Inrush Current FL SWITCH SFNT 5TX(-C) 120 mA 5.0 A for 68 µs FL SWITCH SFNT 8TX(-C) 153 mA 7.0 A for 30 µs FL SWITCH SFNT 4TX/FX(-C) 180 mA 8.1 A for 4 µs FL SWITCH SFNT 7TX/FX(-C) 175 mA 8.0 A for 31 µs FL SWITCH SFNT 7TX/FX ST(-C) 175 mA 8.0 A for 30 µs FL SWITCH SFNT 6TX/2FX(-C) 250 mA 11.6 A for 30 µs FL SWITCH SFNT 6TX/2FX ST(-C) 250 mA 10.8 A for 30 µs 2665_en_I PHOENIX CONTACT 3

FL SWITCH SFNT… Interfaces Total number of RJ45 Ethernet interfaces 4… 8 MAC Address Table Size (Entries) 2 K Properties of RJ45 Ports Connection format 8-pos. RJ45 female connector on the switch Connection medium Twisted-pair cable with a conductor cross section of 0.14mm2 to 0.22 mm2 Cable impedance 100 Ω Transmission speed 10/100 Mbps Maximum network segment length 100 m Properties of Fiber Optic Ports Connection format SC duplex or ST female connector Fiber type Multimode Laser protection Class 1 according to DIN EN 60825-1:2001-11 Transmission rate 100 Mbps full duplex Wavelength 1300/1310 nm Fiber optic segment length 12.1 km glass fiber with F-G 62.5/125 0.7 dB/km F1000 3.3 km glass fiber with F-G 62.5/125 2.6 dB/km F600 7.1 km glass fiber with F-G 50/125 0.7 dB/km F1200 3.1 km glass fiber with F-G 50/125 1.6 dB/km F800 Transmission power (medium type) dynamic (average) Minimum -23.5 dBm (50/125 µm) / -20 dBm (62.5/125 µm) Maximum -14 dBm (50/125 µm) / -14 dBm (62.5/125 µm) Transmission power (medium type) static Minimum -22.5 dBm (50/125 µm) / -19 dBm (62.5/125 µm) Maximum -14 dBm (50/125 µm) / -14 dBm (62.5/125 µm) Receiver sensitivity Minimum -31 dBm (dynamic) / -31 dBm (static) Maximum -14 dBm (dynamic) / -14 dBm (static) Alarm Contacts Voltage 24 V DC Current carrying capacity 100 mA maximum including inrush Mechanical Tests Shock test according to IEC 60068-2-27 Operation: 25g, 11 ms period, half-sine shock pulse Storage/transport: 50g, 11 ms period, half-sine shock pulse Vibration resistance according to IEC 60068-2-6 Operation/storage/transport: 5g, 150 Hz, Criterion 3 Free fall according to IEC 60068-2-32 1 m Conformance With EMC Directives Developed according to IEC 61000-6-2 IEC 61000-4-2 (ESD) Contact: ±4kV, Criterion B Air: ±8kV, Criterion B IEC 61000-4-3 (radiated-noise immunity) 10V/m, Criterion A IEC 61000-4-4 (burst) Ports: ±1 kV, Criterion B DC power: ±2 kV, Criterion B IEC 61000-4-5 (surge) Ports: ±1 kV, Criterion B DC power: ±500 V, Criterion B IEC 61000-4-6 (conducted noise immunity) 10V/m, Criterion A IEC 61000-4-8 (noise immunity against magnetic fields) 30 A/m, Criterion A EN 55022 (noise emission) Class A 2665_en_I PHOENIX CONTACT 4

FL SWITCH SFNT… Conformance With Environmental and EMC Directives for Marine Applications1 Developed according to IEC 60945:2002 8.2 Dry Heat 8.3 Damp Heat (including test of insulation resistance) 8.4 Cold 8.7 Vibration 9 Electromagnetic emission 9.2 Conducted emission 9.3 Radiated emission 10.3 Immunity to conducted radio frequency 10.4 Immunity to radiated radio frequencies 10.5 Immunity to fast transients 10.6 Immunity to surges 10.7 Power supply variations 10.8 Power supply failure 10.9 Electrostatic discharge IEC 60945 Standard magnetic compass Safe compass distance 1.05 m Reduced safe distance 0.65 m IEC 60945 Steering magnetic compass Safe compass distance 0.60 m Reduced safe distance 0.40 m 1 Excludes FL SWITCH SFNT…-C devices Approvals General c u ROHS EEE 2002/95/EC, WEEE 2002/96/EC Hazardous location1 U Class 1, Division 2, Groups A, B, C, D Temp Code T4 installed in minimum IP54 enclosure Marine1 2 F l x o v m 1 Excludes FL SWITCH SFNT…-C devices 2 Excludes SFNT 6TX/2FX and SFNT 6TX/2FX ST devices 2665_en_I PHOENIX CONTACT 5

FL SWITCH SFNT… 5 Overview 5.2 Data Transmission Speed LEDs (2 LEDs/Port) 10 Mbps 100 Mbps LNK/ACT ON/blinking ON/blinking Power connector Power connector 100 OFF ON Power LEDs (US) - green LNK/ACT LED: ON: indicates an electrical link FOLrd S.NWoI.T 2C8H9 1S0F0N4T 4TX/FX FOLrd S.NWoI.T 2C8H9 1S0F0N5T 8TX Flashing: indicates network traffic (at high data US1 US2 Alarm US1 US2 Alarm 100 LANCKT/ 100 LANCKT/ LANCKT/ 100 rates the blinking is in a constant rate) X1 X1 X2 6 Installation 100 LANCKT/ 100 LANCKT/ LANCKT/ 100 CAUTION: X2 X3 X4 Only qualified personnel may start up and operate this device. Qualified personnel are persons 100 LANCKT/ 100 LANCKT/ LANCKT/ 100 authorized to start up, ground and mark devices, systems, and equipment according to the X3 X5 X6 standards of safety technology. 100 LANCKT/ 100 LANCKT/ LANCKT/ 100 NOTE: The FL SWITCH SFNT… module is designed for X4 X7 X8 SELV and PELV operation according to IEC61140/EN61140. 100 LNK/ACT Port X5 100 LED LNK/ACTLED Install the FL SWITCH SFNT… on a clean NS 35 rail. To Security Frame avoid contact resistance use only clean, corrosion-free rails that meet the EN60715 standard. End clamps can be Figure1 Power Connector, LED Locations and Security mounted on both sides of the module to stop the modules Frame from slipping on the rail. 5.1 Diagnostic and Status Indicators NOTE: Des. Color Status Meaning Connect the mounting rail to protective earth US1 and green ON Supply voltage (US) in ground using a grounding terminal block. The US2 the tolerance range modules are grounded when they are snapped onto the rail. Connect protective earth ground OFF Supply voltage (US) too with low impedance. low Alarm red ON US1 or US2 is too low or 6.1 Assembly missing 1. Place the module onto the rail from above. The upper Port link failure holding keyway must be hooked onto the top edge of OFF Normal operation the rail. 2. Push the module from the front towards the mounting surface. 3. Once the module has been snapped on properly, check that it is fixed securely on the rail. 2665_en_I PHOENIX CONTACT 6

FL SWITCH SFNT… 6.2 Removal Snapping the switch onto a grounded rail connects it to the ground potential. In an environment particularly prone to 1. Insert a suitable tool (e.g.,needle-nose pliers) into the EMI, noise immunity can be increased by an additional low- arresting latch and pull it down. impedance connection to protective earth (see Figure3). 2. Pull the module slightly away from the mounting surface. 3. Lift the module from the rail. 6.3 Mounting Plate The FL PA SFNT 5-8 mounting plate provides a method for mounting SFNT 5- and 8-port switches to a flat surface in any orientation. The plate can be mounted on either side of + – + – the switch to allow the network ports to face the proper direction. FL DA SFNT 5-8 adapter allows installation of the switch on a DIN rail with a low profile. The adapter also installs on either side of the switch. US1 GND US2 GND R1 R2 FODMLarad tdPe.-eA:N1 iS4on.. F0T:2Na58i.Tw29 01a510n-8012 X9 US1 GND UUSS12 GUSN2D ALI CAlNTarRK/m1 FO LdR rS2.WN1oI0T0.C28H9 S10F0N7TA LI7CNTTK/X/FXXS2T Figure3 Psuopwpelyr connections for redundant power 100 X1 ALICNTK/ 100 ALICNTK/X4 100 X3 ALICNTK/ 100 ALICNTK/X6 100 X5 ALICNTK/ 100 ALICNTK/X8 100 X7 + – Figure2 FL PA SFNT 5-8 Mounting Plate The dimensions of the FL PA SFNT 5-8 are shown in Figure10. Additional information for the FL PA SFNT 5-8 can be found at US1 GND US2 GND R1 R2 www.phoenixcontact.net/catalog. 6.4 Power Connection Figure4 Power connections for single power supply The switch is designed for SELV and PELV operation at +24VDC according to IEC61140/EN61140. Only SELV and PELV according to the defined standards may be used for supply purposes. 2665_en_I PHOENIX CONTACT 7

FL SWITCH SFNT… Use power conductors between 0.2-2.5 mm² 6.7 Fiber Optic Connection (24-12AWG). Torque connection screws to 0.5-0.6 Nm Two different types of fiber optic connection are available. (5-7lb-in.). The fiber optic connector(s) are located on the lower front face of the 8-port models or on the bottom face of the 5-port 6.5 Alarm Contact models. The FL SWITCH SFNT… switch provides contacts (R1, R2) The ST connectors are typically individual round connectors for remote alarms if a failure is detected. Alarms are and use a 1/4-turn connection. triggered if one or both power supplies fail. An alarm can be The SC connectors have a square interface and the triggered if a port fails. Individual port alarms can be enabled “conductors” are typically locked together through the via a DIP switch located on the bottom of the switch. connector. The alarm relay is a normally closed type. When there are no faults, the contact is held open. When a fault occurs, the relay is de-energized to close the contact. The FL SWITCH SFNT 5... and FL SWITCH SFNT 4... use a five-position DIP switch. The FL SWITCH SFNT 8..., FL TD SWITCH SFNT 7... and FL SWITCH SFNT 6... use an eight- position DIP switch. Each DIP switch position corresponds RD to the port number. To enable an alarm, move the appropriate slider to the ON position. Port OFF ON Iinnd aicdadtietidon b tyo t hthee a rleamrmo tLeE aDla Ormn,. failure is also 12345 N12345O Link Monitor Alarm Failure indication of a fiber optic port can be in either the RX or TX fiber. To disable an alarm, move the appropriate slider to the off DIN Rail clamp position. Figure6 5-port fiber optic ports (SC connectors) 6.6 Ethernet Interface The FL SWITCH SFNT… has five Ethernet ports on the front in RJ45 format to which only twisted-pair cables with an X5 X6 X5 X6 impedance of 100Ω can be connected. The data transmission speed is 10/100Mbps. In addition, every port TD 100 LANCKT/ LANCKT/ 100 RD 100 LANCKT/ LANCKT/ 100 RD has an auto crossing function: it is not necessary to make a TD RD RD distinction between 1:1 or crossover Ethernet cables. RD X7 X8 TD X7 X8 TD RD TD TD Figure7 8-Port ST fiber optic ports RJ45 X5 X6 X5 X6 TD 100 LANCKT/ LANCKT/ 100 RD 100 LANCKT/ LANCKT/ 100 RD RD X7 X8 TD X7 X8 TD 8 7 6 5 4 3 2 1 n.c. TD- n.c. RD- Figure8 8-port SC fiber optic ports n.c. n.c. TD+ RD+ Figure5 RJ45 pin assignment 2665_en_I PHOENIX CONTACT 8

FL SWITCH SFNT… 7 Switching Characteristics 8 Dimensions Store and Forward All data telegrams received by the switch are saved and 14 mm their validity checked. Invalid or faulty data packets (>1522bytes or CRC errors) and fragments (<64bytes) FOLrd S.NWoI.T 2C8H9 1S0F0N4T 4TX/FX FOLrd S.NWoI.T 2C8H9 1S0F0N5T 8TX are rejected. Valid data telegrams are forwarded by the US1 US2 Alarm US1 US2 Alarm switch. The switch always forwards the data using the data 100 LANCKT/ 100 LANCKT/ LANCKT/ 100 transmission speed that is used in the destination network X1 X1 X2 segment. Multi-Address Function 100 LANCKT/ 100 LANCKT/ LANCKT/ 100 The switch independently learns the addresses for X2 X3 X4 termination devices, which are connected via a port, by m m evaluating the source addresses in the data telegrams. Only 100 LANCKT/ 0 100 LANCKT/ LANCKT/ 100 packets with unknown addresses, with a source address of 3 1 this port or with a multicast/broadcast address in the X3 X5 X6 destination address field are forwarded via the corresponding port. The switch can store addresses in its 100 LANCKT/ 100 LANCKT/ LANCKT/ 100 address table with an aging time of 5minutes. This is important when more than one termination device is X4 X7 X8 connected to one or more ports. In this way, several independent subnetworks can be connected to one switch. 100 LNK/ACT Port X5 30 mm 50 mm A restart deletes the entire address table. Depth = 100 mm Quality of Service (QoS): IEEE 802.1P/Q Figure9 Housing dimensions The FL SWITCH SFNT… switches are capable of reading 8.1 FL PA SFNT 5-8 Mounting Plate Ethernet packets that have already been assigned a priority level by a managed switch. In cases of heavy traffic, packets with a priority level between 4 and 7 are considered high m m priority and processed before packets with a priority level 5 between 0 and 3. After prioritization the packets are Ø 5 mm 10. forwarded without modification. 126.4 mm m m 140.0 mm m m 0 0 0. 0. 0 3 1 1 Figure10 FL PA SFNT 5-8 Dimensions 2665_en_I PHOENIX CONTACT 9

FL SWITCH SFNT… 8.2 FL DA SFNT 5-8 Mounting Plate 115.4 mm 5.45 mm 104.5 mm 7 1 6 0 m.4 0 m m m Figure11 FL DA SFNT 5-8 Dimensions 2665_en_I PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany • Phone: +49-(0) 5235-3-00 10 PHOENIX CONTACT • P.O.Box 4100 • Harrisburg • PA 17111-0100 • USA • Phone: +717-944-1300 www.phoenixcontact.com