Coin Vibration Motor Coin Vibrating Motors Coin Vibrator Motors Home | Product Info | About us | Factory tour | ISO Certifications | RoHS Info | Sample Request | Contact us | Email us Part No. C1026B002F 1. General This specification applies to coin permanent-magnetic motors DC model C1026B series. 2. Operating condition Item Specification 2-1 Rated voltage 3.0 V DC 2-2 Operating voltage 2.7~3.3 V DC http://www.vibratormotor.com/vib/c1026b002f.html (1 of 4) [11/9/2009 12:59:24 PM]

Coin Vibration Motor Coin Vibrating Motors Coin Vibrator Motors 2-3 Rotation CW(clockwise) or CCW(contrary clockwise) 2-4 Operating environment -20°C ~+60°C, Ordinary Humidity 2-5 Storage environment -30°C ~+70°C, Ordinary Humidity 3. Measuring condition Item Specification 3-1 Temperature 25±3°C 3-2 Humidity 65±20% RH 3-2 Air pressure 1013±40 hPa 3-4 Power supply DC power supply or battery 3.0V 4. Electrical initial characteristics Item Specification Condition 4-1 Rated speed 9,000 rpm Min At rated voltage 4-2 Rated current 90 mA Max 4-3 Starting current 120 mA Max Motor is rotating at min starting voltage. 4-4 Starting voltage 2.3 V DC Max 4-5 Insulation resistance 10 MW Min At DC 100V between lead wire and case. 31 W ± 15% 4-6 Terminal resistance At 25C° 59 W ± 15% 5. Mechanical characteristics Item Specification 5-1 Bracket deflection strength 9.8 N or more 5-2 Mechanical noise 50 dB(A)Max At rated voltage, back ground noise 28dB(A) Max http://www.vibratormotor.com/vib/c1026b002f.html (2 of 4) [11/9/2009 12:59:24 PM]

Coin Vibration Motor Coin Vibrating Motors Coin Vibrator Motors 6. Durability characteristics Item Specification Requirements After the test, motors shall be approved as specified in 6-1 Lifetime item 7-1. Test cycle 50,000 cycles 6-2 Low temp Temperature : -30°C exposure Time : 96 h 6-3 High temp Temperature : +70°C exposure Time : 96 h After 4 hours exposure in ordinary temperature and humidity, motors shall be approved as specified in item 7-2. Temperature : +40°C 6-4 Humidity Humidity : 95%RH exposure Exposure time : 96 h No condensation of moisture Displacement : 1.5mm (p-p) Frequency: 10~55Hz 6-5 Vibration Acceleration: 22m/s2 After the test motors shall be approved as specified in item 7-2. Period: 10 Minutes log sweep (10~55~10Hz) Condition : This motion shall be applied for a period of 10 minutes in each of 3 mutually perpendicular axes. Test state: Set the motor to the approximately 100 g (include the motor) weight of block drop the motor on the concrete floor. After the test motors shall be approved as specified in 6-6 Free fall Height :1.5 m item 7-2. Direction : ±x, ±y, ±z Number of times: Each 3 times Shock : 29,420 N m/s2 Equivalent (3,000 G) After the test motors shall be approved as specified in 6-7 Heat stock test item 7-2. Test cycle: 15 cycles. 7. Requirements http://www.vibratormotor.com/vib/c1026b002f.html (3 of 4) [11/9/2009 12:59:24 PM]

Coin Vibration Motor Coin Vibrating Motors Coin Vibrator Motors Item Requirements 1) Rated speed: data-30 % Initial Min/ data+50 % Initial Max 2) Rated current: data-30 % Initial Min/ data+50 % Initial Max 7-1 Table A 3) Starting voltage: 2.5 V DC Max 4) Insulation resistance: 10 MW Min 1) Rated speed: Initial data±20 % Max 2) Rated current: Initial data±20 % Max 7-2 Table B 3) Starting voltage: 2.5 V DC Max 4) Terminal resistance: Initial data±15% Max 8. Matters to be paid attention to when using motor 8-1 Unless it is used in accordance with the specifications, the performance and life may be considerably reduced . Due attention should be paid to voltage and range for use 8-2 Avoid use or save the motor in the following environment. 1. High temperature and high humidity area. 2. Corrosive gas such as H S•SO •NO •Cl 2 2 2 2. 3. Dusty area. 8-3 Due attention must be paid to the handling and working environments because such objects as iron powder if attracted by the motor magnent, will cause noise, characteristic deterioration thus reducing the reliability. 8-4 Please confirm enough no problem of standards and laws and ordinances on your cellular. 8-5 To handle the motor, hold the motor case softly. 8-6 Rust of plate (steel) and similar edge should be OK. Home | Product Info | About us | Factory tour | ISO Certifications | RoHS Info | Sample Request | Contact us | Email us Copyright 2009 © VibratorMotor.com http://www.vibratormotor.com/vib/c1026b002f.html (4 of 4) [11/9/2009 12:59:24 PM]