X7R Dielectric General Specifications X7R formulations are called “temperature stable” ceramics and fall into EIA Class II materials. X7R is the most popular of these intermediate dielectric constant materials. Its temperature variation of capacitance is within ±15% from -55°C to +125°C. This capacitance change is non-linear. Capacitance for X7R varies under the influence of electrical operating con-ditions such as voltage and frequency. X7R dielectric chip usage covers the broad spectrum of industrial applications where known changes in capacitance due to applied voltages are acceptable. PART NUMBER (see page 2 for complete part number explanation) 0805 5 C 103 M A T 2 A Size Voltage Dielectric Capacitance Capacitance Failure Terminations Packaging Special (L” x W”) 4V = 4 X7R = C Code (In pF) Tolerance Rate T = Plated Ni and Sn 2 = 7” Reel Code 2 Sig. Digits + A = Not 7 = Gold Plated* 4 = 13” Reel A = Std. 6.3V = 6 J = ± 5%* Number of Zeros Applicable Z= FLEXITERM®** Product 10V = Z K = ±10% Contact 16V = Y M = ± 20% *Optional termination Factory For 25V = 3 Multiples 50V = 5 *≤1µF only, **See FLEXITERM® X7R section 100V = 1 contact factory for 200V = 2 additional values 500V = 7 NOTE: Contact factory for availability of Termination and Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values. 042718 1199

X7R Dielectric Specifications and Test Methods Parameter/Test X7R Specification Limits Measuring Conditions Operating Temperature Range -55ºC to +125ºC Temperature Cycle Chamber Capacitance Within specified tolerance ≤ 10% for ≥ 50V DC rating≤ 12.5% for 25V DC rating Freq.: 1.0 kHz ± 10% ≤ 12.5% for 25V and 16V DC rating Voltage: 1.0Vrms ± .2V Dissipation Factor ≤ 12.5% for ≤ 10V DC rating For Cap > 10µF, 05Vrm @ 120Hz Contact Factory for DF by PN 100,000MΩ or 1000MΩ - µF, Charge device with rated voltage for Insulation Resistance whichever is less 120 ± 5 secs @ room temp/humidity Charge device with 250% of rated voltage for 1-5 seconds, w/charge and discharge current Dielectric Strength No breakdown or visual defects limited to 50 mA (max) Note: Charge device with 150% of rated voltage for 500V devices. Appearance No defects Deflection: 2mm Capacitance Test Time: 30 seconds ≤ ±12% Variation Resistance to Flexure Dissipation Meets Initial Values (As Above) Stresses Factor Insulation ≥ Initial Value x 0.3 Resistance ≥ 95% of each terminal should be covered Dip device in eutectic solder at 230 ± 5ºC Solderability with fresh solder for 5.0 ± 0.5 seconds Appearance No defects, <25% leaching of either end terminal Capacitance ≤ ±7.5% Variation Dissipation Dip device in eutectic solder at 260ºC for 60seconds. Store Resistance to Factor Meets Initial Values (As Above) at room temperature for 24 ± 2hours before Solder Heat Insulation measuring electrical properties. Meets Initial Values (As Above) Resistance Dielectric Meets Initial Values (As Above) Strength Appearance No visual defects Step 1: -55ºC ± 2º 30 ± 3 minutes Capacitance ≤ ±7.5% Step 2: Room Temp ≤ 3 minutes Variation Dissipation Thermal Factor Meets Initial Values (As Above) Step 3: +125ºC ± 2º 30 ± 3 minutes Shock Insulation Meets Initial Values (As Above) Step 4: Room Temp ≤ 3 minutes Resistance Dielectric Repeat for 5 cycles and measure after Meets Initial Values (As Above) Strength 24 ± 2 hours at room temperature Appearance No visual defects Capacitance ≤ ±12.5% Charge device with 1.5 rated voltage (≤ 10V) in Variation test chamber set at 125ºC ± 2ºC for 1000 hours (+48, Dissipation ≤ Initial Value x 2.0 (See Above) -0) Factor Insulation If RV > 10V then Life Test voltage will be 2xRV but Load Life Resistance ≥ Initial Value x 0.3 (See Above) there are exceptions (please contact AVX for further details on exceptions) Dielectric Remove from test chamber and stabilize at room Meets Initial Values (As Above) Strength temperature for 24 ± 2 hours before measuring. Appearance No visual defects Capacitance ≤ ±12.5% Variation Store in a test chamber set at 85ºC ± 2ºC/ 85% ± 5% relative humidity for 1000 hours Dissipation Load Factor ≤ Initial Value x 2.0 (See Above) (+48, -0) with rated voltage applied. Humidity Remove from chamber and stabilize at room Insulation ≥ Initial Value x 0.3 (See Above) temperature and humidity for Resistance 24 ± 2 hours before measuring. Dielectric Meets Initial Values (As Above) Strength 20 051319

X7R Dielectric Capacitance Range PREFERRED SIZES ARE SHADED SIZE 0101* 0201 0402 0603 0805 1206 Soldering Reflow Only Reflow Only Reflow/Wave Reflow/Wave Reflow/Wave Reflow/Wave Packaging Paper/Embossed All Paper All Paper All Paper Paper/Embossed Paper/Embossed mm 0.40 ± 0.02 0.60 ± 0.03 1.00 ± 0.10 1.60 ± 0.15 2.01 ± 0.20 3.20 ± 0.20 (L) Length (in) (0.016 ± 0.0008) (0.024 ± 0.001) (0.040 ± 0.004) (0.063 ± 0.006) (0.079 ± 0.008) (0.126 ± 0.008) mm 0.20 ± 0.02 0.30 ± 0.03 0.50 ± 0.10 0.81 ± 0.15 1.25 ± 0.20 1.60 ± 0.20 (W) Width (in) (0.008 ± 0.0008) (0.011 ± 0.001) (0.020 ± 0.004) (0.032 ± 0.006) (0.049 ± 0.008) (0.063 ± 0.008) mm 0.10± 0.04 0.15 ± 0.05 0.25 ± 0.15 0.35 ± 0.15 0.50 ± 0.25 0.50 ± 0.25 (t) Terminal (in) (0.004 ± 0.0016) (0.006 ± 0.002) (0.010 ± 0.006) (0.014 ± 0.006) (0.020 ± 0.010) (0.020 ± 0.010) WVDC 16 6.3 10 16 25 50 6.3 10 16 25 50 6.310 16 25 50 100200250 6.3 10 16 25 50 1002002506.3 10 16 25 50100200250500 Cap 100101 B A A A A A C C C G G G (pF) 150151 B A A A A A C C C G G G 220221 B A A A A A C C C G G G E E E E E E E 330331 B A A A A A C C C G G G J J J J J J K 470471 B A A A A A C C C G G G J J J J J J K 680681 B A A A A C C C G G G J J J J J J K 1000102 B A A A A C C C C G G G G J J J J J J J J K 1500152 B A A A A C C C C G G J G J J J J J J J J J J J J J J M 2200222 B A A A A C C C C G G J G J J J J J J J J J J J J J J M 3300332 A A A A C C C C G G J G J J J J J J J J J J J J J J M 4700472 A A A A C C C C G G J G J J J J J J J J J J J J J J M 6800682 A A A A C C C C G G J G J J J J J J J J J J J J J J P Cap 0.01103 A A A A C C C C G G G J G J J J J J J J J J J J J J J P (µF) 0.015153 C C C C G G G J J J J J J J N J J J J J M J Q 0.022223 C C C C G G G J J J J J N N J J J J J M J Q 0.033333 C C C C G G J J J J J N N N J J J J J M J Q 0.047473 C C C C G G G J J J J J N N N J J J J J M M 0.068683 C C C C G G G J J J J J N N J J J J J P M 0.1104 C C C C G G G G J J J J J N N J J J J P P P 0.15154 G G G G J J J J N N J J J J Q Q Q 0.22224 C C C G G J J J J J N N N J J J J Q Q Q 0.33334 J J J J J N N N N N J J M P Q 0.47474 C C J J J J J N N N N N M M M P Q 0.68684 J J J N N N M M 1.0105 C J J J J J N N N N M M 2.2225 J J J P P P P** Q Q Q Q Q** 4.7475 J P P P Q Q Q Z 10106 P P P Q Q X X 22226 X Q Q 47476 Q Q 100107 WVDC 16 6.3 10 16 25 50 6.3 10 16 25 50 6.310 16 25 50 100200250 6.3 10 16 25 50 1002002506.3 10 16 25 50100200250500 SIZE 0101 0201 0402 0603 0805 1206 Letter A B C E G J K M N P Q X Y Z Max. 0.33 0.22 0.56 0.71 0.90 0.94 1.02 1.27 1.40 1.52 1.78 2.29 2.54 2.79 Thickness (0.013) (0.009) (0.022) (0.028) (0.035) (0.037) (0.040) (0.050) (0.055) (0.060) (0.070) (0.090) (0.100) (0.110) PAPER EMBOSSED NOTE: Contact factory for non-specified capacitance values *EIA 01005 **Contact Factory for Specifications 21 041719

X7R Dielectric Capacitance Range PREFERRED SIZES ARE SHADED SIZE 1210 1812 1825 2220 2225 Soldering Reflow Only Reflow Only Reflow Only Reflow Only Reflow Only Packaging Paper/Embossed All Embossed All Embossed All Embossed All Embossed mm 3.30 ± 0.4 4.50 ± 0.30 4.50 ± 0.30 5.70 ± 0.40 5.72 ± 0.25 (L) Length (in.) (0.130± 0.016) (0.177 ± 0.012) (0.177 ± 0.012) (0.225 ± 0.016) (0.225 ± 0.010) mm 2.50 ± 0.20 3.20 ± 0.20 6.40 ± 0.40 5.00 ± 0.40 6.35 ± 0.25 (W) Width (in.) (0.098 ± 0.008) (0.126 ± 0.008) (0.252 ± 0.016) (0.197 ± 0.016) (0.250 ± 0.010) mm 0.50 ± 0.25 0.61 ± 0.36 0.61 ± 0.36 0.64 ± 0.39 0.64 ± 0.39 (t) Terminal (in.) (0.020 ± 0.010) (0.024 ± 0.014) (0.024 ± 0.014) (0.025 ± 0.015) (0.025 ± 0.015) WVDC 10 16 25 50 100 200 500 16 25 50 100 200 500 50 100 200 25 50 100 200 500 50 100 200 Cap 100 101 (pF) 150 151 220 221 330 331 470 471 680 681 1000 102 1500 152 J J J J J J M 2200 222 J J J J J J M 3300 332 J J J J J J M 4700 472 J J J J J J M 6800 682 J J J J J J M Cap 0.01 103 J J J J J J M K K K K K M M M X X X X M P P (µF) 0.015 153 J J J J J J P K K K K P M M M X X X X M P P 0.022 223 J J J J J J Q K K K K P M M M X X X X M P P 0.033 333 J J J J J J Q K K K K X M M M X X X X M P P 0.047 473 J J J J J J Q K K K K Z M M M X X X X M P P 0.058 683 J J J J J M Q K K K K Z M M M X X X X M P P 0.1 104 J J J J J M X K K K K Z M M M X X X X M P P 0.15 154 J J J J M Z K K K P Z M M M X X X X M P X 0.22 224 J J J J P Z K K K P Z M M M X X X X M P X 0.33 334 J J J J Q K K M X M M X X X X M P X 0.47 474 M M M M Q K K P X M M X X X X M P X 0.68 684 M M P X X M M Q M P X X M P X 1.0 105 N N P X Z M M X Z M P X X M P X 1.5 155 N N Z Z Z Z Z Z Q X X M X Z 2.2 225 X X Z Z Z Z Z Z X X M X Z 3.3 335 X X Z Z Z Z Z Z X Z 4.7 475 Z Z Z Z Z Z Z X Z 10 106 Z Z Z Z Z Z Z 22 226 Z Z Z Z 47 476 Z 100 107 WVDC 10 16 25 50 100 200 500 16 25 50 100 200 500 50 100 200 25 50 100 200 500 50 100 200 SIZE 1210 1812 1825 2220 2225 Letter A B C E G J K M N P Q X Y Z Max. 0.33 0.22 0.56 0.71 0.90 0.94 1.02 1.27 1.40 1.52 1.78 2.29 2.54 2.79 Thickness (0.013) (0.009) (0.022) (0.028) (0.035) (0.037) (0.040) (0.050) (0.055) (0.060) (0.070) (0.090) (0.100) (0.110) PAPER EMBOSSED NOTE: Contact factory for non-specified capacitance values 22 101618