F E D C B A NOTES: n1,04 (15x) 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI ( 5 : 1 ) FOR 30 MINUTES AFTER SOLDERING 4. METALSHELL: ZINC DIE CAST; min. 50µin NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0, BLACK D 6. O-RING: SILICONE PER ASTM D2000 70 SHORE A D 7. RUBBER GASKET: TPE 43 8. SEALING COMPOUND: EPOXY RESIN UL 94 V-0; BLACK 0,+-0, 9 . CPLOANTTINACGT (SS:E CEO PPAPRETR N AOL)L:OY 2,1 0,4+-0,3 1 6 o PLEASE ADD 1 for 30µin HARD GOLD over min. 50µin NICKEL 9, o PLEASE ADD 3 for 8µin HARD GOLD over min. 50µin NICKEL SOLDER CUP ACCEPTS CABLE AWG 22 10. HEXLOCKING SCREWS: STAINLESS STEEL 11. RECOMMENDED PANEL CUT-OUT ON SHEET 2 12. RECOMMENDED TORQUE FOR MOUNTING SCREW b 35Ncm (3.1 in.LB) / max.67Ncm (6 in.LB) 5 13. CONNECTOR IS PART MARKED: 15-00065o CONEC ABC 1218 0,20 0,0, +- +- 6 6 3, 8,23+0,25 -0 39,4+-00,3 b POS. 1 RUBBER GASKET 25+0,12 -0,13 PLACED ON TOP SURFACE POS. 6 C 16,81+0,23 OF MALE INSULATOR C -0,02 POS. 11 3 0,0 +- 1 1, 2 10° SEALING COMPOUND O-RING 15-00065o B CONEC ABC B 4-40 UNC 6 4, SEE NOTE 13 4 9, SW 4,8 4-40 UNC b AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. Directive 2002/95/EC RoHS compliant A I IIL##L#APPRVAFREABEDEBCAEAUTRZACNOGOGOO CNC UAOAAMPPSMPPTEPRRO:AOOMNVVEAAYLLR N ## AA FFPMRRPEEERII:GGOAABBVEEA L## DDDEEABBTLLEOO:CC AAT GGITEEL ##E AA:UUTTOORRIIZZAACCIIOONN ## AAPPPPRROOVVAALL APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION IIITYTEPEHSDRANGANBCDRMOOOW , IEPEYYYTRRDUCDNANAANDANOMOW IIEPETTPTYTTBASSDNAHRDARHUOOOW .IIITTEPERNRSSNMOW IIEPPYTFEbNRSHANDCRGHCNCGHOOOOWm I LTATERCARABYADONODDNGHNDW 3re axv b. desÄOc 3rri4gip3int5ion 30d.a09te.09 naHmSe nddaopr-aorptmwldodn.ler12 73ad..11an00te.c.00e88 dimF nPisae.cm tkhineeerr mmR smtdpicwataalregltte:e nn:riooa::l: D11w-55iStphKoU 1hs1e.B5 AxS-l oO20McL802ksIDAnie:00nEv1egL6e R n(En s5 5octCo to:reHUer1 sw 1P)(D0see notseDh 9A:I)N31- A F E D C B A

F E D C B A D D Solder Instruction 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350°C, 50 Watt max. and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. C C RECOMMENDED PANEL CUT-OUT 20,5`0,1 i0,26A B 1 0, B ` B 4 1, 1 ) x 2 ( 5 0 0, ` 1 R 3, 10°`1° 3, i0,26B n 4 ` 0, 1 25`0,1 3 A A I IIL##L#APPRVAFREABEDEBCAEAUTRZACNOGOGOO CNC UAOAAMPPSMPPTEPRRO:AOOMNVVEAAYLLR N ## AA FFPMRRPEEERII:GGOAABBVEEA L## DDDEEABBTLLEOO:CC AAT GGITEEL ##E AA:UUTTOORRIIZZAACCIIOONN ## AAPPPPRROOVVAALL APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION IIITYTEPEHSDRANGANBCDRMOOOW , IEPEYYYTRRDUCDNANAANDANOMOW IIEPETTPTYTTBASSDNAHRDARHUOOOW .IIITTEPERNRSSNMOW IIEPPYTFEbNRSHANDCRGHCNCGHOOOOWm I LTATERCARABYADONODDNGHNDW rea v. desOcrri gipintion da te nam e nddaopr-aorptmwldodn.ler12 73ad..11an00te.c.00e88 dimF nPisae.cm tkhineeerr mmR smtdpicwataalregltte:e Dnn:r-iooaS::lU:B PM1wAA5iLtNhEKs hEeH1eeLDAx l o1s2Ccs5h8kepIUnie0enov gTse5se. hn : st-S 1eOct1oOreertUL w11D0TER CUsPDhA:IN32- A F E D C B A