Y5V Dielectric General Specifications Y5V formulations are for general-purpose use in a limited temperature range. They have a wide temperature characteristic of +22% –82% capacitance change over the operating temperature range of –30°C to +85°C. These characteristics make Y5V ideal for decoupling applications within limited temperature range. PART NUMBER (see page 2 for complete part number explanation) 0805 3 G 104 Z A T 2 A Size Voltage Dielectric Capacitance Capacitance Failure Terminations Packaging Special (L" x W") 6.3V = 6 Y5V = G Code (In pF) Tolerance Rate T = Plated Ni 2 = 7" Reel Code 10V = Z 2 Sig. Digits + Z = +80 –20% A = Not and Sn 4 = 13" Reel A = Std. 16V = Y Number of Applicable Product 25V = 3 Zeros 50V = 5 Temperature Coefficient Capacitance Change Insulation Resistance vs. Temperature vs. DC Bias Voltage s)10,000 d ++2100 +40 Fara nce -100 +20 Ohm- 1,000 (cid:2)% Capacita -----6543200000 (cid:2) c/c (%) ---6420000 n Resistance ( 100 -70 o -80 -80 ulati -55 -35 -15 +5 +25 +45 +65 +85+105+125 -1000 20 40 60 80 100 Ins 0 +20 +30 +40 +50 +60 +70 +80 +90 Temperature °C % DC Bias Voltage Temperature °C 0.1 (cid:4)F - 0603 0.22 (cid:4)F - 0805 1 (cid:4)F - 1206 Impedance vs. Frequency Impedance vs. Frequency Impedance vs. Frequency 10,000 1,000 1,000 1,000 100 100 ms) 100 ms) 10 ms) 10 Oh 10 Oh Oh |Z| ( 1 |Z| ( 1 |Z| ( 1 0.1 0.1 0.1 0.01 0.01 0.01 10,000 100,000 1,000,000 10,000,000 10,000 100,000 1,000,000 10,000,000 10,000 100,000 1,000,000 10,000,000 Frequency (Hz) Frequency (Hz) Frequency (Hz) 30 101316

Y5V Dielectric Specifications and Test Methods Parameter/Test Y5V Specification Limits Measuring Conditions Operating Temperature Range -30ºC to +85ºC Temperature Cycle Chamber Capacitance Within specified tolerance ≤ 5.0% for ≥ 50V DC rating Freq.: 1.0 kHz ± 10% ≤ 7.0% for 25V DC rating Voltage: 1.0Vrms ± .2V Dissipation Factor ≤ 9.0% for 16V DC rating For Cap > 10 μF, 0.5Vrms @ 120Hz ≤ 12.5% for ≤ 10V DC rating 10,000MΩ or 500MΩ - μF, Charge device with rated voltage for Insulation Resistance whichever is less 120 ± 5 secs @ room temp/humidity Charge device with 250% of rated voltage for Dielectric Strength No breakdown or visual defects 1-5 seconds, w/charge and discharge current limited to 50 mA (max) Appearance No defects Deflection: 2mm Capacitance Test Time: 30 seconds ≤ ±30% Resistance to Variation Flexure Dissipation Meets Initial Values (As Above) Stresses Factor Insulation ≥ Initial Value x 0.1 Resistance ≥ 95% of each terminal should be covered Dip device in eutectic solder at 230 ± 5ºC Solderability with fresh solder for 5.0 ± 0.5 seconds Appearance No defects, <25% leaching of either end terminal Capacitance ≤ ±20% Variation Dip device in eutectic solder at 260ºC for 60 Dissipation Resistance to Meets Initial Values (As Above) seconds. Store at room temperature for 24 ± 2 Factor Solder Heat hours before measuring electrical properties. Insulation Meets Initial Values (As Above) Resistance Dielectric Meets Initial Values (As Above) Strength Appearance No visual defects Step 1: -30ºC ± 2º 30 ± 3 minutes Capacitance ≤ ±20% Step 2: Room Temp ≤ 3 minutes Variation Dissipation Thermal Meets Initial Values (As Above) Step 3: +85ºC ± 2º 30 ± 3 minutes Factor Shock Insulation Meets Initial Values (As Above) Step 4: Room Temp ≤ 3 minutes Resistance Dielectric Repeat for 5 cycles and measure after Meets Initial Values (As Above) Strength 24 ±2 hours at room temperature Appearance No visual defects Capacitance Charge device with twice rated voltage in ≤ ±30% Variation test chamber set at 85ºC ± 2ºC Dissipation for 1000 hours (+48, -0) ≤ Initial Value x 1.5 (See Above) Load Life Factor Insulation Remove from test chamber and stabilize ≥ Initial Value x 0.1 (See Above) Resistance at room temperature for 24 ± 2 hours Dielectric before measuring. Meets Initial Values (As Above) Strength Appearance No visual defects Store in a test chamber set at 85ºC ± 2ºC/ Capacitance ≤ ±30% 85% ± 5% relative humidity for 1000 hours Variation (+48, -0) with rated voltage applied. Load Dissipation ≤ Initial Value x 1.5 (See above) Humidity Factor Remove from chamber and stabilize at Insulation ≥ Initial Value x 0.1 (See Above) room temperature and humidity for Resistance 24 ± 2 hours before measuring. Dielectric Meets Initial Values (As Above) Strength 31 101316

Y5V Dielectric Capacitance Range PREFERRED SIZES ARE SHADED Size 0201 0402 0603 0805 1206 1210 Soldering Reflow Only Reflow/Wave Reflow/Wave Reflow/Wave Reflow/Wave Reflow/Wave Packaging All Paper All Paper All Paper Paper/Embossed Paper/Embossed Paper/Embossed mm 0.60 ± 0.09 1.00 ± 0.10 1.60 ± 0.15 2.01 ± 0.20 3.20 ± 0.20 3.20 ± 0.20 (L) Length (in.) (0.024 ± 0.004) (0.040 ± 0.004) (0.063 ± 0.006) (0.079 ± 0.008) (0.126 ± 0.008) (0.126 ± 0.008) mm 0.30 ± 0.09 0.50 ± 0.10 .81 ± 0.15 1.25 ± 0.20 1.60 ± 0.20 2.50 ± 0.20 (W) Width (in.) (0.011 ± 0.004) (0.020 ± 0.004) (0.032 ± 0.006) (0.049 ± 0.008) (0.063 ± 0.008) (0.098 ± 0.008) mm 0.15 ± 0.05 0.25 ± 0.15 0.35 ± 0.15 0.50 ± 0.25 0.50 ± 0.25 .50 ± 0.25 (t) Terminal (in.) (0.006 ± 0.002) (0.010 ± 0.006) (0.014 ± 0.006) (0.020 ± 0.010) (0.020 ± 0.010) (0.020 ± 0.010) WVDC 6.3 10 6 10 16 25 50 10 16 25 50 10 16 25 50 10 16 25 50 10 16 25 50 Cap 820 (pF) 1000 A 2200 A 4700 A Cap 0.010 A A (µF) 0.022 A 0.047 A C 0.10 C C G G K 0.22 G 0.33 G 0.47 C G G 1.0 C C G G J N N N M M M N 2.2 C J N N K Q 4.7 N N N P Q N N 10.0 N P Q Q X X Q Q X 22.0 Q X Z 47.0 WVDC 6.3 10 6 10 16 25 50 10 16 25 50 10 16 25 50 10 16 25 50 10 16 25 50 Size 0201 0402 0603 0805 1206 1210 Letter A C E G J K M N P Q X Y Z Max. 0.33 0.56 0.71 0.90 0.94 1.02 1.27 1.40 1.52 1.78 2.29 2.54 2.79 Thickness (0.013) (0.022) (0.028) (0.035) (0.037) (0.040) (0.050) (0.055) (0.060) (0.070) (0.090) (0.100) (0.110) PAPER EMBOSSED 32 012319